Dell™ PowerEdge™ R905 Manuel du propriétaire
Remarques, avis et précautions REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : Un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION : Une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document peuvent être modifiées sans préavis.
Sommaire 1 À propos du système . Autres informations utiles . . . . . . . . . . . . . . . 11 . . . . . . . . . . . . . . . 11 Fonctions du système accessibles au démarrage . . . 12 . . . . 14 . . . . . . . . 16 Voyants et caractéristiques du panneau avant . Codes des voyants de disques durs Voyants et caractéristiques du panneau arrière . . . . 18 . . . . . . . 19 . . . . . . . . . . . . 19 . . . . . . . . . . . . . . .
2 Utilisation du programme de configuration du système . . . . . . . . . . . . . . . . . . . . . . . 49 Accès au programme de configuration du système . . . . . . . . . . . . . . . . . . . . . . . . 49 Réponse aux messages d'erreur . . . . . . . . . . 50 Utilisation du programme de configuration du système . . . . . . . . . . . . . . . . . . . . . 50 . . . . . . . . . . 51 . . . . . . . . . . . . . . . . . . .
3 Installation des composants du système . . . . . . . . . . . . . . Outils recommandés . . . . . . . . . 71 . . . . . . . . . . . . . . . . . . 72 À l'intérieur du système . . . . . . . . . . . . . . . . . Retrait et réinstallation du cadre avant en option Ouverture et fermeture du système 72 . . . 74 . . . . . . . . . . . 75 Ouverture du système . . . . . . . . . . . . . . . 75 Fermeture du système . . . . . . . . . . . . . . . 77 . . . . . . . . . . . . . . . . . . . . . . .
Retrait de la carte de montage . . . . . . . . . . . . . . . . . . 94 . . . . . . . . . . . . . . . . . . . . . . . . 94 Réinstallation de la carte de montage Carte RAC Installation d'une carte RAC en option . Clé de mémoire USB interne (en option) . . . . . . 94 . . . . . . . . 96 Installation de la clé de mémoire USB interne en option . . . . . . . . . . . . . . . . . . . . . . 98 . . . . . . . . . . . . . . . . 99 Carte mémoire SD . . . . . . . . . . . . . . . . . . . .
Installation d'un disque dur enfichable à chaud . . . . . . . . . . . . . . . . . . . . . . . 124 . . . . . . . . 125 . . . . . . . . . . . . . . . . . 127 Réinstallation d'un disque dur dans un support . . . . . . . . . . . . . Cartes contrôleurs SAS Retrait d'une carte contrôleur SAS . . . . . . . . Installation d'une carte contrôleur SAS . . . . . . Installation de la batterie de la carte contrôleur RAID SAS . . . . . . . . . . . . . . . . . . . . . 127 . 129 . . . . 129 . . . . . . .
Carte adaptatrice pour les ventilateurs . . . . . . . . . Retrait d'une carte adaptatrice pour les ventilateurs . . . . . . . . . . . . . . . . . . . Installation d'une carte adaptatrice pour les ventilateurs . . . . . . . . . . . . . . Carte système 148 . . . . . . . . . . . . . . . . . . . . . . 149 . . . . . . . . . . . . . Installation de la carte système . . . . . . . . . . Carte de distribution de l'alimentation . . . . . . . . . Retrait de la carte de distribution de l'alimentation . . .
Dépannage d'un NIC Dépannage d'un système mouillé . Dépannage de la pile du système . . . . . . . . . . 171 . . . . . . . . . . . 172 Dépannage des blocs d'alimentation . . . . . 174 . . . . . . . . . . . . 174 Dépannage de la mémoire système . . . . . . . . . . . 176 . . . . . . . . . . . . 178 . . . . . . . . . . . . . . . 179 Dépannage d'un lecteur optique Dépannage d'un disque dur 173 . . . . . . . . . Dépannage des problèmes de refroidissement du système . . . . . . . . . . . . .
Utilisation des options de test personnalisées . . . . . 191 . . . . . . . . 191 Sélection d'options de diagnostic . . . . . . . . . 192 Visualisation des informations et des résultats . . . . . . . . . . . . . . . . . . . . 192 Sélection de périphériques à tester 6 Cavaliers et connecteurs Cavaliers de la carte système . . . . . . . . . . . . . . . . . . . . . . . . . Désactivation d'un mot de passe oublié Connecteurs de la carte système 193 . . . . . . . . 194 . . . . . . . . . . . .
À propos du système Cette section décrit les caractéristiques essentielles au fonctionnement du système (matériel, micrologiciel et interface logicielle). Les connecteurs situés sur les panneaux avant et arrière du système permettent au système de bénéficier d'une connectivité optimale et de nombreuses possibilités d'extension. Le micrologiciel, le système d'exploitation et les applications gèrent le système ainsi que l'état des composants. Ils vous alertent lorsqu'un incident survient.
• Les CD fournis avec le système contiennent des documents et des outils relatifs à la configuration et à la gestion du système. • La documentation des logiciels de gestion de systèmes contient des informations sur les fonctionnalités, l'installation et l'utilisation de base de ces logiciels, ainsi que sur la configuration requise. • La documentation du système d'exploitation indique comment installer (au besoin), configurer et utiliser le système d'exploitation.
Tableau 1-1. Touches d'accès aux fonctions du système Touche(s) Description Permet d'accéder au programme de configuration du système. Voir “Utilisation du programme de configuration du système”, à la page 49. Ouvre le menu principal de la partition d'utilitaires, qui permet d'accéder aux diagnostics du système. Voir “Exécution des diagnostics du système”, à la page 190. Permet d'accéder à l'écran de sélection d'un périphérique d'amorçage.
Voyants et caractéristiques du panneau avant La figure 1-1 présente les boutons, les voyants et les connecteurs situés derrière le cadre de rack (en option) sur le panneau avant. Figure 1-1. Voyants et caractéristiques du panneau avant 1 Tableau 1-2. 2 3 5 6 7 8 Connecteurs et caractéristiques du panneau avant Numéro Composant 1 4 Icône Voyant et bouton d'alimentation Description Le bouton d'alimentation contrôle la sortie du bloc d'alimentation en CC qui alimente le système.
Tableau 1-2. Connecteurs et caractéristiques du panneau avant (suite) Numéro Composant 2 Bouton NMI Icône Description Ce bouton est utilisé pour la résolution de certains incidents liés aux logiciels et aux pilotes de périphériques avec certains systèmes d'exploitation. Pour l'activer, utilisez la pointe d'un trombone. Appuyez sur ce bouton uniquement si un technicien de support qualifié vous demande de le faire, ou si cela est préconisé dans la documentation du système d'exploitation.
Tableau 1-2. Connecteurs et caractéristiques du panneau avant (suite) Numéro Composant Icône Description 5 Connecteurs USB (2) Permettent de connecter des périphériques compatibles USB 2.0 au système. 6 Connecteur vidéo Permet de connecter un moniteur au système. 7 Disques durs (en option) Cinq lecteurs 3,5 pouces ou huit lecteurs 2,5 pouces. 8 Lecteur optique (en option) Lecteur optique slim (en option) REMARQUE : Les périphériques DVD sont uniquement des périphériques de données.
Le tableau 1-3 répertorie les codes des voyants de disques durs connectés à une carte contrôleur avec fonction RAID (carte PERC6i, par exemple). Ces codes varient en fonction des événements affectant les lecteurs du système. Par exemple, si un disque dur tombe en panne, la séquence “Échec du disque” apparaît. Lorsque vous avez sélectionné le lecteur à retirer, la séquence “Préparation au retrait” apparaît, suivie de la séquence “Lecteur prêt à être inséré ou retiré”.
Voyants et caractéristiques du panneau arrière La figure 1-3 présente les boutons, les voyants et les connecteurs situés sur le panneau arrière du système. Figure 1-3.
Connexion de périphériques externes Appliquez les consignes suivantes lorsque vous connectez des périphériques externes au système : • La plupart des périphériques doivent être reliés à un connecteur spécifique et requièrent l'installation de pilotes pour pouvoir fonctionner correctement. Les pilotes sont généralement fournis avec le système d'exploitation ou avec le périphérique lui-même.
Tableau 1-5. Voyants des blocs d'alimentation Voyant Fonction État du bloc d'alimentation Un voyant vert indique que le bloc d'alimentation fonctionne normalement. Panne du bloc d'alimentation Un voyant orange indique qu'un incident lié au bloc d'alimentation s'est produit. État de l'alimentation en CA Un voyant vert indique qu'une source de courant alternatif valide est reliée au bloc d'alimentation. Figure 1-4.
Codes des voyants de NIC Chaque NIC du panneau arrière est équipé d'un voyant qui fournit des informations sur l'activité du réseau et l'état du lien. Voir figure 1-5. Le tableau 1-6 répertorie les codes des voyants de NIC. Figure 1-5. Voyants de NIC 1 1 2 Voyant de lien Tableau 1-6. 2 Voyant d'activité Codes des voyants de NIC Voyant Code du voyant Les voyants de lien et d'activité sont éteints. Le NIC n'est pas connecté au réseau. Le voyant de lien est vert.
Messages d'état affichés sur l'écran LCD L'écran LCD du panneau de commande affiche des messages d'état indiquant si le système fonctionne correctement ou s'il requiert une intervention. Il s'allume en bleu en cas de fonctionnement normal et en orange si une erreur est détectée. Dans ce dernier cas, il affiche un message comprenant un code d'état suivi d'un texte descriptif. Le tableau 1-7 répertorie les messages d'état qui peuvent s'afficher sur l'écran LCD et indique leur cause probable.
Tableau 1-7. Messages d'état affichés sur l'écran LCD Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives N/A Chaîne de 62 caractères pouvant être définie par l'utilisateur dans le programme de configuration du système. Ce message est affiché uniquement pour information. NOM DU SYSTÈME Vous pouvez modifier la chaîne système dans le Ce nom s'affiche dans les programme de configuracas suivants : tion du système.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E12nn n PwrGd Panne du régulateur de tension indiqué. voir “Obtention d'aide”, à la page 203. E1229 CPU n VCORE Panne du régulateur de tension VCORE du processeur n. voir “Obtention d'aide”, à la page 203. E122A CPU n VTT La tension VTT du voir “Obtention d'aide”, à processeur n a dépassé les la page 203. limites autorisées.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E123C Planar LOM PwrGd Panne du régulateur de tension pour le NIC intégré. Mettez le système hors tension et rallumez-le ou effacez le journal d'événements. Si l'incident persiste, voir “Obtention d'aide”, à la page 203. E1310 RPM Fan nn Le nombre de tours par minute du ventilateur indiqué est en dehors des limites autorisées.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E1414 La température du microprocesseur spécifié est en dehors des limites autorisées et celui-ci s'est arrêté. voir “Dépannage des problèmes de refroidissement du système”, à la page 174. Si l'incident persiste, assurez-vous que les dissipateurs de chaleur du microprocesseur sont correctement installés.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E141C CPU Mismatch La configuration des pro- Vérifiez que les procescesseurs n'est pas prise en seurs sont de même type charge. et conformes aux spécifications décrites dans le document Getting Started Guide (Guide de mise en route) du système. E141F CPU Protocol Le BIOS du système a voir “Obtention d'aide”, à renvoyé une erreur de pro- la page 203.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E161C PS n Input Lost La source d'alimentation du bloc d'alimentation indiqué est indisponible ou en dehors des limites autorisées. Vérifiez la source de CA du bloc d'alimentation indiqué. Si l'incident persiste, voir “Dépannage des blocs d'alimentation”, à la page 173.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E1711 PCI PERR Bnn Le BIOS du système a Dnn Fnn renvoyé une erreur de parité PCI liée à un PCI PERR composant résidant dans Slot n l'espace de configuration PCI du bus nn, périphérique nn, fonction nn.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes E171F Le BIOS du système a renvoyé une erreur fatale PCIe liée à un composant résidant dans l'espace de configuration PCI du bus nn, périphérique nn, fonction n. PCIE Fatal Err Bnn Dnn Fnn PCIE Fatal Err Slot n Mesures correctives Retirez la carte d'extension PCI indiquée et remboîtez-la dans son connecteur.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E1A15 SAS Cable B Le câble SAS B est mal inséré, manquant ou endommagé. Vérifiez la connexion du câble au niveau du fond de panier SAS. Voir “Connecteurs de la carte de fond de panier SAS”, à la page 199. E1A1C LOM Mezz Missing La carte réseau fille est manquante. Installez la carte réseau fille ou remboîtez-la dans le connecteur.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E2016 Int Controller Échec du contrôleur d'interruptions. voir “Obtention d'aide”, à la page 203. E2017 Timer Fail Échec de rafraîchissement du temporisateur. voir “Obtention d'aide”, à la page 203. E2018 Prog Timer Échec du temporisateur d'intervalle programmable. voir “Obtention d'aide”, à la page 203. E2019 Parity Error Erreur de parité.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E201F DRAC Config Échec de la configuration Vérifiez si l'écran affiche du contrôleur d'accès des messages d'erreur distant (RAC). spécifiques. Assurez-vous que la carte RAC et les câbles correspondants sont correctement emboîtés dans les connecteurs appropriés. Voir “Carte RAC”, à la page 94.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives E2111 SBE Log Disable DIMM nn Le BIOS du système a voir “Dépannage de la désactivé la consignation mémoire système”, à la des erreurs de mémoire page 176. portant sur un seul bit (SBE) jusqu'au prochain redémarrage du système. “nn” représente la barrette DIMM indiquée par le BIOS.
Tableau 1-7. Messages d'état affichés sur l'écran LCD (suite) Message Message affiché affiché sur sur la ligne 2 la ligne 1 Causes Mesures correctives I1915 Video Off La vidéo a été désactivée Ce message s'affiche par l'utilisateur du conuniquement à titre (L'écran LCD trôleur RAC. d'information. affiche un arrièreplan bleu ou orange.) I1916 Video Off in La vidéo sera désactivée Ce message s'affiche nn dans nn secondes par uniquement à titre l'utilisateur du contrôleur d'information.
Résolution des incidents décrits par les messages d'état de l'écran LCD Le code et le texte affichés sur l'écran LCD permettent souvent d'identifier une panne précise pouvant facilement être corrigée. Par exemple, le code E0708 PROC_1_Presence indique qu'aucun microprocesseur n'est installé dans le support 1. En outre, il est possible de déterminer la cause de l'incident si plusieurs erreurs de même type surviennent.
Messages système Le système affiche des messages d'erreur pour informer l'utilisateur qu'un incident s'est produit. Le tableau 1-8 répertorie les messages qui peuvent s'afficher et indique leur cause probable, ainsi que les mesures correctives appropriées. REMARQUE : Si vous recevez un message du système qui n'est pas répertorié dans le tableau 1-8, vérifiez la documentation de l'application que vous utilisiez au moment où le message est apparu.
Tableau 1-8. Messages système (suite) Message Causes BIOS Manufacturing Le système est en mode mode detected. assemblage. MANUFACTURING MODE will be cleared before the next boot. System reboot required for normal operation. BIOS Update Attempt Failed! Mesures correctives Redémarrez le système pour lui faire quitter le mode assemblage. La tentative de mise à Faites une nouvelle tentative jour à distance du BIOS a de mise à jour du BIOS. Si échoué.
Tableau 1-8. Messages système (suite) Message Causes !*** Error: Remote Échec de l'initialisation Access Controller du contrôleur d'accès initialization distant (DRAC). failure *** RAC virtual USB devices may not be available... Mesures correctives Assurez-vous que le contrôleur DRAC est correctement installé. Voir “Installation d'une carte RAC en option”, à la page 94. Gate A20 failure Contrôleur du clavier défectueux ; carte système défectueuse.
Tableau 1-8. Messages système (suite) Message Causes Mesures correctives Keyboard Contrôleur du clavier Controller failure défectueux ; carte système défectueuse. voir “Obtention d'aide”, à la page 203. Manufacturing mode Le système est en mode detected assemblage. Redémarrez le système pour lui faire quitter le mode assemblage. Barrette(s) de mémoire défectueuse(s) ou mal installée(s). voir “Dépannage de la mémoire système”, à la page 176.
Tableau 1-8. Messages système (suite) Message Causes Mesures correctives No boot device available Sous-système du lecteur optique ou du disque dur défectueux ou manquant ; disque dur défectueux ou manquant ; aucune disquette d'amorçage dans le lecteur A. Utilisez une disquette, un CD ou un disque dur amorçable. Si l'incident persiste, voir “Dépannage d'un lecteur optique”, à la page 178 et “Dépannage d'un disque dur”, à la page 179.
Tableau 1-8. Messages système (suite) Message Causes PCIe Degraded Link Carte PCIe défectueuse Width Error: ou mal installée dans le Embedded support spécifié. Bus#nn/Dev#nn/Func n Expected Link Width is n Mesures correctives Remboîtez la carte PCIe dans le support dont le numéro est indiqué. Voir “Installation d'une carte d'extension”, à la page 89. Si l'incident persiste, voir “Obtention d'aide”, à la page 203.
Tableau 1-8. Messages système (suite) Message Causes Mesures correctives Plug & Play Configuration Error Erreur d'initialisation d'un périphérique PCI ; carte système défectueuse. Installez la fiche du cavalier NVRAM_CLR et redémarrez le système. Voir figure 6-1 pour identifier l'emplacement des cavaliers. Si l'incident persiste, voir “Dépannage des cartes d'extension”, à la page 184.
Tableau 1-8. Messages système (suite) Message Causes ROM bad checksum = Carte d'extension défecaddress tueuse ou mal installée. Mesures correctives Remboîtez les cartes d'extension dans leur logement. Vérifiez que tous les câbles sont correctement enfichés dans les cartes d'extension. Si l'incident persiste, voir “Dépannage des cartes d'extension”, à la page 184. Disque dur défectueux. voir “Dépannage d'un disque dur”, à la page 179. Shutdown failure Échec du test d'arrêt.
Tableau 1-8. Messages système (suite) Message Causes Time-of-day not set - please run SETUP program Paramètres d'heure ou de Vérifiez les paramètres de date incorrects ; pile du l'heure et de la date. système défectueuse. Voir “Utilisation du programme de configuration du système”, à la page 49. Si l'incident persiste, remplacez la pile du système. Voir “Pile du système”, à la page 131. Timer chip counter Carte système défectu2 failed euse. Mesures correctives voir “Obtention d'aide”, à la page 203.
Tableau 1-8. Messages système (suite) Message Causes Mesures correctives Warning! No microcode update loaded for processor n La mise à jour du microcode a échoué. Mettez le micrologiciel du BIOS à jour. Si l'incident persiste, voir “Obtention d'aide”, à la page 203. Warning: One or more faulty DIMMs found on CPUn Les barrettes de mémoire voir “Dépannage de la mémutilisées par le processeur oire système”, à la page 176. n sont défectueuses ou mal installées.
Messages d'avertissement Un message d'avertissement signale un problème possible et vous demande une réponse avant de laisser le système poursuivre son exécution. Par exemple, lorsque vous lancez le formatage d'une disquette, un message vous avertit que vous allez perdre toutes les données qu'elle contient. Les messages d'avertissement interrompent la tâche en cours et vous demandent de répondre en tapant y (pour oui) ou n (pour non).
À propos du système
Utilisation du programme de configuration du système Après avoir installé le système, lancez le programme de configuration pour vous familiariser avec la configuration et les paramètres facultatifs disponibles. Notez ces informations pour pouvoir vous y reporter ultérieurement.
Réponse aux messages d'erreur Vous pouvez accéder au programme de configuration du système en répondant à certains messages d'erreur. Si un message d'erreur s'affiche quand le système démarre, prenez-en note. Avant d'accéder au programme de configuration du système, voir “Messages système”, à la page 37 pour trouver une explication du message et des suggestions de correction.
Tableau 2-1. Touches de navigation du programme de configuration du système (suite) Touches Action Affiche l'aide du programme de configuration du système. REMARQUE : Pour la plupart des options, les modifications effectuées sont enregistrées mais ne prennent effet qu'au redémarrage du système. Options de configuration du système Écran principal Lorsque vous accédez au programme de configuration du système, son écran principal apparaît (voir figure 2-1). Figure 2-1.
Le tableau 2-2 répertorie les options et les descriptions des champs qui apparaissent dans l'écran principal du programme de configuration du système. Pour plus d'informations, voir “Options de l'écran System Security (Sécurité du système)”, à la page 60. REMARQUE : Les options disponibles varient en fonction de la configuration du système. REMARQUE : Les valeurs par défaut sont répertoriées sous l'option correspondante, le cas échéant. Tableau 2-2.
Tableau 2-2. Options du programme de configuration du système (suite) Option Description USB Flash Drive Emulation Type (Option par défaut : Auto) Détermine le type d'émulation pour le lecteur flash USB. L'option Hard disk (Disque dur) permet au lecteur flash USB de fonctionner comme un disque dur. L'option Floppy (Lecteur de disquette) permet au lecteur flash USB de se comporter comme un lecteur de disquette amovible.
Tableau 2-2. Options du programme de configuration du système (suite) Option Description Keyboard NumLock (Option par défaut : On [Activé]) Détermine si le système démarre en mode VERR NUM s'il est équipé d'un clavier à 101 ou 102 touches (cette option ne s'applique pas aux claviers à 84 touches). Report Keyboard Errors (Option par défaut : Report [Signaler]) Active ou désactive la consignation des erreurs liées au clavier pendant l'auto-test de démarrage.
Tableau 2-3. Écran Memory Information (Informations sur la mémoire) (suite) Option Description Node Interleaving Lorsque ce champ est activé, l'imbrication de mémoire est (Option par défaut : prise en charge si une configuration de mémoire symétrique Disabled [Désactivé]) est installée. Si ce champ est défini sur Disabled (Désactivé), le système peut prendre en charge l'accès mémoire NUMA (Non-Uniform Memory Architecture [Architecture mémoire non uniforme]).
Écran CPU Information (Informations sur le processeur) Le tableau 2-4 répertorie les options et les descriptions des champs qui apparaissent dans l'écran CPU Information (Informations sur le processeur). Tableau 2-4. Écran CPU Information (Informations sur le processeur) Option Description 64-bit Indique si le ou les processeurs installés prennent en charge les extensions 64 bits. Core Speed Affiche la vitesse d'horloge du ou des processeurs.
Activation de la technologie AMD PowerNow!™ La technologie AMD PowerNow! contrôle les performances du processeur du système en réglant automatiquement sa fréquence de fonctionnement et sa tension en fonction de la tâche exécutée. Elle permet d'économiser une quantité considérable d'énergie lorsqu'une application ne requiert pas des performances optimales.
Tableau 2-5. Options de l'écran Integrated Devices (Périphériques intégrés) (suite) Option Description Internal USB Port (Option par défaut : On [Activé]) Active ou désactive le port USB interne du système. SD Card Port Active ou désactive le port de carte SD interne du système. REMARQUE : Ce port est réservé à un hyperviseur, s'il est installé. Embedded Gb NICx (Option par défaut : NIC 1 = Enabled with PXE [Activé avec PXE], autres NIC = Enabled [Activé]) Active ou désactive les NIC intégrés.
Écran Serial Communication (Communication série) Le tableau 2-6 répertorie les options et les descriptions des champs qui apparaissent dans l'écran Serial Communication (Communication série). Tableau 2-6.
Écran System Security (Sécurité du système) Le tableau 2-7 répertorie les options et les descriptions des champs qui apparaissent dans l'écran System Security (Sécurité du système). Tableau 2-7. Options de l'écran System Security (Sécurité du système) Option Description System Password Affiche l'état actuel de la fonction de protection par mot de passe et permet d'attribuer et de confirmer un nouveau mot de passe système.
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option Description TPM Security (Option par défaut : Off [Désactivé]) REMARQUE : La fonction TPM n'est pas disponible en Chine. Définit les modalités de déclaration de la puce TPM (Trusted Platform Module) dans le système. Lorsque l'option Off (Désactivé) est sélectionnée, la présence de la puce TPM n'est pas signalée au système d'exploitation.
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option Description TPM Clear (Option par défaut : No) AVIS : L'effacement de la puce TPM entraîne la perte de toutes les clés de cryptage qu'elle contient. Cette opération empêche le démarrage du système d'exploitation. Si les clés de cryptage ne peuvent pas être restaurées, des données risquent d'être perdues. Vous devez donc impérativement créer une copie de sauvegarde des clés TPM avant d'activer cette option.
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option Description AC Power Recovery (Option par défaut : Last [Dernier]) Détermine le comportement du système au retour de l'alimentation secteur. L'option Last (Dernier) indique que le système doit revenir au même état qu'avant la coupure d'alimentation. Avec l'option On (Marche), le système démarre dès que l'alimentation en CA est rétablie.
Vous ne pouvez changer ou supprimer un mot de passe que si vous le connaissez (voir “Suppression ou modification d'un mot de passe système existant”, à la page 66). Si vous avez oublié votre mot de passe, vous ne pourrez pas faire fonctionner le système ni modifier sa configuration tant qu'un technicien de maintenance qualifié n'aura pas désactivé et effacé les mots de passe en déplaçant le cavalier approprié sur la carte mère.
3 Tapez le nouveau mot de passe système. Le mot de passe peut contenir jusqu'à 32 caractères. Les caractères entrés ne sont pas affichés dans le champ ; ils sont remplacés (y compris les espaces) par des caractères génériques. Le mot de passe ne tient pas compte de la différence entre majuscules et minuscules. Cependant, certaines combinaisons de touches ne sont pas valides.
Pour désactiver la protection par mot de passe : 1 Démarrez le système ou redémarrez-le en appuyant sur . 2 Tapez le mot de passe et appuyez sur . Si l'option Password Status (État du mot de passe) a la valeur Locked (Verrouillé) lorsque vous allumez ou redémarrez le système (en appuyant sur ), tapez votre mot de passe et appuyez sur à l'invite.
5 Vérifiez que l'option System Password (Mot de passe système) est définie sur Not Enabled (Non activé). Si tel est le cas, le mot de passe système a été supprimé. Si l'option System Password (Mot de passe système) est définie sur Enabled (Activé), appuyez sur pour redémarrer le système, puis recommencez les étapes 2 à 5. Utilisation du mot de passe de configuration Lisez les sections suivantes pour attribuer ou modifier le mot de passe de configuration.
Une fois le mot de passe confirmé, le paramètre Setup Password (Mot de passe de configuration) prend la valeur Enabled (Activé). La prochaine fois que vous accéderez au programme de configuration, le système vous demandera d'entrer le mot de passe de configuration. La modification du mot de passe de configuration prend effet immédiatement (il n'est pas nécessaire de redémarrer le système).
Désactivation d'un mot de passe oublié voir “Désactivation d'un mot de passe oublié”, à la page 194. Configuration du contrôleur BMC Le contrôleur BMC (Baseboard Management Controller) permet de configurer, contrôler et restaurer les systèmes à distance.
Options du module de configuration du contrôleur BMC Pour plus d'informations concernant les options du module de configuration du contrôleur BMC et du port EMP (port de gestion d'urgence), consultez le document BMC User's Guide (Contrôleur BMC - Guide d'utilisation).
Installation des composants du système Cette section décrit l'installation des composants suivants : • Cadre avant • Capot du système • Modules de ventilation • Assemblage du protecteur de ventilation • Blocs d'alimentation • Module d'extension processeurs (PEM) • Cartes d'extension • Carte de montage • Carte RAC • Clé de mémoire USB interne • Clé TOE/iSCSI • Carte mémoire SD • Carte réseau fille • Mémoire système • Processeurs • Lecteur optique • Disques durs • Carte cont
• Commutateur d'intrusion du châssis • Carte de fond de panier SAS • Carte adaptatrice pour les périphériques • Carte adaptatrice pour les ventilateurs • Carte système • Carte de distribution de l'alimentation • Carte du module d'extension processeurs Outils recommandés Vous pouvez avoir besoin des éléments suivants pour exécuter les procédures décrites dans cette section : • Clé du verrou du système • Tournevis cruciforme n°2 • Tournevis Torx T10 • Petit tournevis plat • Bracelet ant
Figure 3-1.
La carte système contient les circuits de contrôle du système et d'autres composants électroniques. Les processeurs et les barrettes de mémoire sont installés sur la carte système et sur le module d'extension processeurs (Processor Expansion Module ou “PEM”) disponible en option. Les baies de disque dur peuvent accueillir huit disques 2,5 pouces, ou bien cinq disques SAS 3,5 pouces. Tous ces disques sont disponibles en option.
Pour réinstaller le cadre en option, accrochez sa partie droite sur le châssis, puis remboîtez le cache sur le système. Fermez le verrou pour verrouiller le cadre. Voir figure 3-2. Ouverture et fermeture du système PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique.
Figure 3-3.
Fermeture du système 1 Soulevez le loquet du capot. 2 Alignez le capot avec les bords gauche et droit du système. Décalez-le légèrement vers l'arrière de façon que les plots situés sur le bord interne du capot s'alignent sur les crochets. Voir figure 3-3. 3 Rabattez le capot sur le châssis et refermez le loquet. 4 Tournez le verrou du loquet de fermeture dans le sens des aiguilles d'une montre pour verrouiller le capot.
Figure 3-4.
Réinstallation d'un ventilateur REMARQUE : La procédure d'installation est la même pour tous les ventilateurs. 1 Vérifiez que la poignée du ventilateur est relevée et enfoncez ce dernier sur le support jusqu'à ce qu'il soit correctement emboîté. Abaissez la poignée du ventilateur jusqu'à ce que vous entendiez un déclic. Voir figure 3-4. 2 Refermez le système. Voir “Fermeture du système”, à la page 77.
Figure 3-5.
Réinstallation de l'assemblage du protecteur de ventilation 1 Abaissez doucement le protecteur de ventilation dans le système. Les rivets situés aux quatre coins du protecteur de ventilation doivent s'emboîter dans les plots d'alignement correspondants de la carte système. Voir figure 3-5. 2 Appuyez doucement sur l'assemblage du protecteur de ventilation jusqu'à ce qu'il soit correctement emboîté.
Figure 3-6. Retrait et réinstallation d'un bloc d'alimentation 1 2 3 1 Bloc d'alimentation 3 Loquet du levier d'éjection 2 Levier d'éjection Réinstallation d'un bloc d'alimentation 1 Tout en maintenant le levier ouvert, insérez le nouveau bloc d'alimentation dans le châssis jusqu'à ce que le levier touche le châssis. Voir figure 3-6. 2 Refermez le levier d'éjection jusqu'à ce que le bloc d'alimentation soit positionné correctement. Le levier doit alors s'enclencher derrière le loquet.
AVIS : Lorsque vous connectez le câble d'alimentation, faites-le passer dans la boucle du serre-câble. REMARQUE : Après avoir installé un nouveau bloc d'alimentation dans un système équipé de deux modules, patientez quelques secondes pour que le système reconnaisse ce module et détermine son état. Le voyant du bloc d'alimentation s'allume en vert si ce dernier fonctionne normalement (voir figure 1-4).
Figure 3-7. Installation et retrait d'un module PEM 1 2 3 4 1 Module d'extension processeurs 2 Poignée 3 Broches de guidage (6) 4 Fentes (6) AVIS : Utilisez vos deux mains pour retirer le module PEM du châssis.
4 Sortez le module PEM du châssis en le soulevant. 5 Si le module PEM retiré contient quatre processeurs, retournez-le doucement et faites pivoter la poignée pour la fermer avant de placer le module PEM sur un plan de travail. Voir figure 3-8. Figure 3-8.
Pour accéder à la carte du module PEM, retirez le protecteur de ventilation. Voir figure 3-9. Figure 3-9.
Réinstallation du module PEM ou de son boîtier 1 Réinstallez le protecteur de ventilation. 2 Tournez le module PEM de façon à placer la carte interne (systèmes à quatre processeurs) ou la chicane d'air (systèmes biprocesseurs) vers le bas. 3 Ouvrez complètement la poignée du module PEM. 4 Alignez les trois broches de guidage situées de chaque côté du module PEM avec les fentes correspondantes, sur les côtés du châssis. Voir figure 3-7.
Figure 3-10.
Installation d'une carte d'extension PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Figure 3-11. Installation ou retrait d'une carte d'extension 2 1 3 1 Carte d'extension 3 Connecteur latéral 2 Dispositif de fixation des cartes d'extension 7 Connectez tous les câbles requis sur la carte d'extension. • Si vous installez une carte RAC, voir “Carte RAC”, à la page 94. • Si vous installez une carte contrôleur SAS, voir “Installation d'une carte contrôleur SAS”, à la page 127. 8 Refermez le système. Voir “Fermeture du système”, à la page 77.
Retrait d'une carte d'extension PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Carte de montage Deux cartes de montage sont disponibles pour votre système : • Une carte de montage 2P (deux processeurs) • Une carte de montage 4P (quatre processeurs) Figure 3-12. Cartes de montage 1 2 1 Carte de montage 4P 2 Carte de montage 2P Retrait de la carte de montage PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
1 Éteignez le système et les périphériques connectés, puis débranchez-le de la prise secteur. 2 Ouvrez le système. Voir “Ouverture du système”, à la page 75. 3 Retirez le module PEM. Voir “Retrait du module PEM ou de son boîtier”, à la page 83. 4 Pour retirer la carte de montage, soulevez les deux loquets de fixation correspondants jusqu'à ce que la carte sorte de son support. Soulevez ensuite la carte pour l'extraire du châssis. Voir figure 3-13. Figure 3-13.
1 Carte de montage 2 Loquets de fixation (2) 3 Support de la carte de montage 4 Plots de guidage (2) Réinstallation de la carte de montage 1 Le cas échéant, déposez les capuchons de protection des connecteurs sur la carte de montage. 2 Ouvrez les deux loquets de retenue sur la carte de montage, et orientez la carte comme indiqué sur la figure 3-13.
2 Ouvrez le système. Voir “Ouverture du système”, à la page 75. 3 Retirez l'obturateur de prise en plastique du panneau arrière du système. Voir figure 1-3. 4 Retirez temporairement la carte contrôleur de stockage du logement INTERNAL_STORAGE : a Déconnectez tous les câbles de la carte. b Tenez la carte contrôleur de stockage par les coins et retirez-la doucement de son connecteur.
1 Connecteur de NIC RJ-45 de la carte RAC 3 Connecteur du câble de gestion (50 broches) 2 Connecteur du câble MII (44 broches) 7 Réinstallez la carte contrôleur de stockage. 8 Reconnectez tous les câbles à la carte contrôleur de stockage. 9 Refermez le système. Voir “Fermeture du système”, à la page 77. 10 Rebranchez le système et les périphériques sur leur source d'alimentation, puis allumez-les.
système. Voir “Utilisation du programme de configuration du système”, à la page 49. Pour obtenir les instructions permettant de créer un fichier d'amorçage sur la clé de mémoire USB, consultez la documentation fournie avec cette dernière.
Installation de la clé de mémoire USB interne en option PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
7 Accédez au programme de configuration du système et vérifiez que la clé USB a été détectée. Voir “Utilisation du programme de configuration du système”, à la page 49. Clé TOE/iSCSI (en option) Le moteur TOE, les fonctions iSCSI et d'autres fonctionnalités qui seront disponibles à l'avenir pour les NIC intégrés du système sont activés via l'installation d'une clé de NIC matérielle (en option) dans le connecteur TOE_KEY de la carte système.
Figure 3-16. Installation d'une clé TOE/iSCSI 1 2 1 Clé TOE/iSCSI 2 Connecteur de clé TOE/iSCSI 5 Le cas échéant, réinstallez la carte d'extension dans le logement 7. Voir “Installation d'une carte d'extension”, à la page 89. 6 Refermez le système. Voir “Ouverture du système”, à la page 75. 7 Rebranchez le système sur la prise secteur et redémarrez-le.
Carte mémoire SD Vous pouvez installer une carte mémoire SD (en option) dans un connecteur de la carte système. PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique.
1 Éteignez le système et les périphériques connectés, puis débranchez-le de la prise secteur. 2 Ouvrez le système. Voir “Ouverture du système”, à la page 75. 3 Si des cartes d'extension sont installées dans les logements 6 et 7, retirezles temporairement afin d'installer la carte. Voir “Retrait d'une carte d'extension”, à la page 91. 4 Placez la carte de sorte que ses connecteurs de NIC se trouvent face à l'ouverture appropriée du panneau arrière. Voir figure 3-17. Figure 3-17.
6 Repoussez légèrement la carte vers l'arrière. Alignez le bord avant de la carte NIC avec les deux picots de fixation avant en plastique, qui se trouvent à côté du connecteur de la carte système. Appuyez sur le côté de la carte jusqu'à ce qu'elle soit correctement emboîtée. Voir figure 3-17. Lorsque l'avant de la carte est en place, le picot de plastique se referme sur son rebord.
7 Le cas échéant, réinstallez les cartes d'extension dans les logements 6 et 7. Voir “Installation d'une carte d'extension”, à la page 89. 8 Refermez le système. Voir “Ouverture du système”, à la page 75. 9 Rebranchez le système sur la prise secteur et redémarrez-le. Retrait de la carte réseau fille PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
Mémoire système Vous pouvez ajouter de la mémoire supplémentaire au système (maximum autorisé : 128 Go pour les systèmes biprocesseur ou 256 Go pour les systèmes quadriprocesseur). Pour ce faire, installez des paires de barrettes de mémoire de 512 Mo, 1 Go, 2 Go, 4 Go ou 8 Go. Les barrettes de 8 Go seront prises en charge lorsqu'elles seront disponibles. Les barrettes de mémoires DDR-II à registres et cadencées à 667 MHz sont prises en charge dans toutes les capacités.
La mémoire peut être installée dans une configuration comprenant deux processeurs (voir tableau 3-1) ou quatre processeurs (voir tableau 3-2). Tableau 3-1.
Tableau 3-2.
Tableau 3-2.
Installation de barrettes de mémoire PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Figure 3-18. Installation et retrait d'une barrette de mémoire 1 2 3 1 Barrette de mémoire 3 Détrompeur 2 Dispositifs d'éjection (2) 8 Alignez le connecteur latéral de la barrette avec le détrompeur du support, puis insérez la barrette dans le support. REMARQUE : Le détrompeur permet de s'assurer que la barrette sera insérée dans le bon sens.
11 Réinstallez l'assemblage du protecteur de ventilation : – Si vous installez des barrettes de mémoire sur la carte système, voir “Réinstallation de l'assemblage du protecteur de ventilation”, à la page 81. – Si vous installez des barrettes de mémoire dans le module PEM, voir figure 3-9. 12 Réinstallez le module PEM. Voir “Réinstallation du module PEM ou de son boîtier”, à la page 87. 13 Refermez le système. Voir “Fermeture du système”, à la page 77.
3 Retirez le module PEM. Voir “Retrait du module PEM ou de son boîtier”, à la page 83. 4 Retirez l'assemblage du protecteur de ventilation : – Si vous retirez des barrettes de mémoire de la carte système, voir “Retrait de l'assemblage du protecteur de ventilation”, à la page 79. – Si vous retirez des barrettes de mémoire du module PEM, voir figure 3-9. 5 Repérez les supports mémoire. Voir figure 6-1.
Processeurs Le système peut prendre en charge deux ou quatre processeurs. Pour tirer parti des futures options en matière de vitesse et des nouvelles fonctionnalités émergentes, vous pouvez mettre les processeurs existants à niveau. Chaque processeur et sa mémoire cache interne sont contenus dans une matrice LGA (Land Grid Array) installée dans un support situé sur la carte système ou le module d'extension processeurs.
AVIS : Ne retirez jamais le dissipateur de chaleur d'un processeur si vous n'avez pas l'intention de retirer le processeur lui-même. Le dissipateur de chaleur est indispensable pour maintenir les conditions de température adéquates. 6 Desserrez l'une des vis de fixation du dissipateur de chaleur. Voir figure 3-19. Figure 3-19.
9 Si le dissipateur de chaleur ne s'est pas détaché du processeur, faites-le doucement tourner dans le sens des aiguilles d'une montre, puis dans l'autre sens jusqu'à ce qu'il se décolle. Ne tirez pas sur le dissipateur de chaleur pour l'arracher du processeur. 10 Soulevez le dissipateur de chaleur pour le retirer du processeur et retournez-le avant de le poser. 11 À l'aide d'un chiffon propre et non pelucheux, retirez la pâte thermique qui recouvre la surface du cadre de protection du processeur.
13 Ouvrez le cadre de protection du processeur puis retirez le processeur de son support. Laissez le levier relevé afin de pouvoir installer le nouveau processeur. AVIS : Veillez à ne pas tordre les broches du support lors du retrait du processeur. Vous risqueriez d'endommager définitivement le support et la carte système. Installation d'un processeur 1 Déballez le nouveau processeur. 2 Alignez le processeur avec les deux détrompeurs du support. Voir figure 3-20.
5 Installez le dissipateur de chaleur. REMARQUE : Si aucun nouveau dissipateur de chaleur n'est fourni, utilisez celui que vous avez retiré à l'étape 10. a Si un nouveau dissipateur de chaleur vous a été fourni avec le kit du processeur, retirez le feuillet de protection de la couche de pâte thermique déjà appliquée sur le dessus du dissipateur. Voir figure 3-19.
11 Exécutez les diagnostics du système pour vérifier que le nouveau processeur fonctionne correctement. voir “Exécution des diagnostics du système”, à la page 189 pour plus d'informations concernant l'exécution des diagnostics. Installation d'un lecteur optique Il est possible de monter un lecteur optique slim (en option) sur un plateau qui s'installe dans le panneau avant et se connecte au contrôleur de la carte système par l'intermédiaire du fond de panier SAS.
Figure 3-21.
5 Installez le nouveau lecteur optique dans le support. Voir figure 3-21. Les plots du support doivent s'engager dans les trous correspondants, sur le côté du lecteur. 6 Fixez la carte d'interface sur l'arrière du support, à l'aide des deux rivets de plastique. Voir figure 3-21. 7 Réinstallez le loquet et serrez la vis moletée. 8 Insérez le support contenant le lecteur jusqu'à ce que le plateau s'enclenche. Voir figure 3-19. 9 Réinstallez le cadre avant, le cas échéant.
Figure 3-22. ID des disques durs ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 0 ID 1 ID 2 ID 3 ID 4 Avant de commencer AVIS : Avant de tenter de retirer ou d'installer un lecteur pendant que le système est en cours de fonctionnement, reportez-vous à la documentation de la carte contrôleur RAID SAS (en option) pour vérifier que la configuration de l'adaptateur hôte lui permet de prendre en charge le retrait et l'insertion de lecteurs à chaud.
Il vous faudra peut-être utiliser des programmes autres que ceux fournis avec le système d'exploitation pour partitionner et formater les disques durs. AVIS : Pendant le formatage du lecteur, vous ne devez pas éteindre ni redémarrer le système. Cela risquerait d'endommager le lecteur. Lorsque vous formatez un disque dur à haute capacité, prévoyez suffisamment de temps pour que le formatage s'exécute entièrement. De longs délais de formatage sont normaux pour ces lecteurs.
Installation d'un cache de lecteur Le cache de lecteur est muni d'un détrompeur permettant de s'assurer qu'il sera correctement inséré dans la baie. Pour installer un cache de lecteur, insérez et faites pivoter le côté avec détrompeur dans la baie de lecteur. Appuyez de manière égale sur l'autre côté du cache jusqu'à ce qu'il soit correctement emboîté. Retrait d'un disque dur enfichable à chaud 1 Retirez le cadre. Voir “Retrait et réinstallation du cadre avant en option”, à la page 74.
Figure 3-23. Retrait et installation d'un disque dur enfichable à chaud 1 2 3 1 Disque dur 3 Poignée d'éjection du support 2 Support de disque Installation d'un disque dur enfichable à chaud AVIS : Lorsque vous installez un disque dur, assurez-vous que les lecteurs adjacents ne sont pas en cours d'installation.
1 Retirez le cadre. Voir “Retrait et réinstallation du cadre avant en option”, à la page 74. 2 Si la baie est fermée par un cache, retirez-le. Voir “Retrait d'un cache de lecteur”, à la page 122. 3 Installez le disque dur enfichable à chaud. a Ouvrez la poignée du support de disque dur. b Insérez le support de disque dans la baie jusqu'à ce qu'il touche le fond de panier. c Refermez la poignée pour maintenir le disque dur en place. 4 Réinstallez le cadre avant, le cas échéant.
Figure 3-24.
Cartes contrôleurs SAS Retrait d'une carte contrôleur SAS PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
4 Connectez la carte au fond de panier SAS. a Enfichez le connecteur du câble de données SAS marqué “Controller 0” dans le connecteur blanc de la carte. Enfichez ensuite le connecteur “Controller 1” dans le connecteur noir de la carte. Voir figure 3-25.
1 Support de la batterie RAID 2 Batterie RAID 3 Câble de la batterie RAID 4 Câble de données SAS 5 Carte contrôleur RAID SAS Installation de la batterie de la carte contrôleur RAID SAS Installez la pile RAID dans le support en plastique correspondant qui se trouve à l'intérieur du châssis. Enfichez le câble de la batterie dans le connecteur situé sur la carte contrôleur RAID SAS, à côté de la barrette de mémoire RAID. Voir figure 3-25.
10 Rebranchez le système et les périphériques sur les prises secteur, puis allumez-les. 11 Effectuez une sauvegarde sur bande et un test de vérification de l'unité, en suivant les instructions de la documentation correspondante. Connexion d'un périphérique de stockage Fibre Channel externe Cette sous-section décrit le raccordement de périphériques Fibre Channel externes et d'un adaptateur HBA Fibre Channel (en option).
Pile du système La pile du système est une pile bouton de 3,0 volts (V). Remplacement de la pile du système PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique.
b Tout en continuant à appuyer, poussez la pile vers le côté positif et extrayez-la des pattes de fixation du côté négatif du connecteur. Figure 3-26. Remplacement de la pile du système 1 2 3 1 Côté positif du connecteur de pile 3 Côté négatif du connecteur de pile 2 Pile du système AVIS : Pour ne pas endommager le connecteur de pile, maintenez-le en place lorsque vous installez ou retirez une pile. 7 Installez la nouvelle pile.
12 Accédez au programme de configuration du système pour vérifier que la pile fonctionne correctement. Voir “Utilisation du programme de configuration du système”, à la page 49. 13 Entrez l'heure et la date exactes dans les champs Time (Heure) et Date du programme de configuration du système. 14 Quittez le programme de configuration du système. 15 Pour tester la pile qui vient d'être installée, éteignez le système et débranchez-le de la prise secteur pendant au moins une heure.
6 Retirez les trois vis Torx qui fixent la carte du panneau de commande au châssis, puis retirez cette carte.
7 Retirez le module d'affichage : a Insérez le bout d'un trombone dans l'orifice situé sur le côté droit du module d'affichage, puis retirez doucement l'étiquette. b Retirez les deux vis Torx qui fixent le module d'affichage au châssis. 8 Retirez le module d'affichage. Figure 3-27.
Installation du panneau de commande 1 Insérez le module d'affichage du panneau de commande dans l'ouverture du châssis et fixez-le à l'aide des deux vis Torx. 2 Collez l'étiquette du panneau de commande sur le module d'affichage. 3 Installez la carte du panneau de commande dans le châssis et fixez-la à l'aide des trois vis Torx. Voir figure 3-27. 4 Enfichez le câble du module d'affichage dans la carte du panneau de commande. Voir figure 3-27.
4 Tirez doucement sur le commutateur d'intrusion pour le dégager de son clip. Figure 3-28. Retrait et installation du commutateur d'intrusion du châssis 1 2 1 Commutateur d'intrusion 2 Câble du commutateur d'intrusion Installation du commutateur d'intrusion du châssis 1 Enfichez le câble du commutateur d'intrusion dans le connecteur approprié de la carte système. Voir figure 3-28.
4 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. Fond de panier SAS Retrait du fond de panier SAS PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique.
8 Si vous retirez un fond de panier pour lecteurs 3,5 pouces, débranchez le câble du panneau de commande enfiché dans le connecteur situé à l'avant du fond de panier. Voir figure 3-29. 9 Déconnectez les câbles d'alimentation et de données SAS enfichés dans l'arrière du fond de panier SAS. 10 Retirez le fond de panier SAS du système : a Si vous retirez un fond de panier pour lecteurs 2,5 pouces, poussez la patte de fixation bleue vers l'avant du système, puis soulevez le fond de panier. Voir figure 3-29.
Figure 3-29.
Figure 3-30.
Installation d'un fond de panier SAS 1 Installez le fond de panier SAS : a Insérez doucement le fond de panier dans le système, en prenant garde de ne pas endommager ses composants. b Positionnez la fente d'alignement (au bas du fond de panier) sur le plot d'alignement situé au fond du châssis. Voir figure 3-30. c Emboîtez les fentes de fixation du fond de panier sur les crochets correspondants du châssis. d Abaissez le fond de panier jusqu'à ce que le plot de fixation bleu s'enclenche.
Carte adaptatrice pour les périphériques Retrait d'une carte adaptatrice pour les périphériques PRÉCAUTION : Toute procédure d'installation nécessitant le retrait du capot du système doit être effectuée uniquement par des techniciens de maintenance qualifiés. Consultez le document Product Information Guide (Guide d'information sur le produit) pour obtenir des informations complètes sur les consignes de sécurité, les interventions dans l'ordinateur et la protection contre les décharges électrostatiques.
Figure 3-31.
10 Retirez la carte adaptatrice pour les périphériques : a Appuyez sur la patte de fixation bleue et soulevez la carte. Voir figure 3-31. b Lorsque la carte est au niveau le plus haut possible, tirez-la vers l'arrière du système pour la dégager des crochets de fixation. c Retirez la carte du système, en prenant garde de ne pas endommager les composants situés sur celle-ci. d Posez la carte adaptatrice sur un plan de travail, face vers le bas.
Carte adaptatrice pour les ventilateurs Retrait d'une carte adaptatrice pour les ventilateurs PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Figure 3-32.
Installation d'une carte adaptatrice pour les ventilateurs 1 Insérez les deux pattes de fixation de la carte adaptatrice dans les fentes correspondantes, sur le côté de la baie de ventilateurs. Voir figure 3-32. 2 Fixez la carte adaptatrice à l'aide des deux vis. 3 Réinstallez le fond de panier SAS (systèmes avec disques durs 3,5 pouces) ou la carte adaptatrice pour les périphériques (systèmes avec disques durs 2,5 pouces).
Carte système Retrait de la carte système PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Figure 3-33. Retrait et installation du compartiment de la batterie RAID 1 2 3 4 1 3 Compartiment de la batterie RAID Pattes de fixation (2) 2 4 Patte d'éjection Fentes de fixation (2) 13 Retirez la carte système : 150 a Tirez sur le plot de fixation bleu situé au milieu de la carte système, puis faites glisser cette dernière vers l'avant du châssis jusqu'à ce qu'elle bute. Voir figure 3-34. b Saisissez la carte système en la tenant par les dissipateurs de chaleur ou la carte de montage.
Figure 3-34.
Installation de la carte système 1 Transférez les processeurs et les dissipateurs de chaleur sur la nouvelle carte système. Voir “Retrait d'un processeur”, à la page 113 et “Installation d'un processeur”, à la page 116. 2 Retirez les barrettes de mémoire de l'ancienne carte et installez-les sur la nouvelle, aux mêmes emplacements. Voir “Retrait de barrettes de mémoire”, à la page 111 et “Installation de barrettes de mémoire”, à la page 109. 3 Transférez la carte de montage sur la nouvelle carte système.
7 Branchez les câbles dans l'ordre indiqué ci-dessous (voir figure 6-1 et figure 6-3 pour identifier l'emplacement des connecteurs sur la carte système et sur le fond de panier SAS) : • Trois câbles de distribution de l'alimentation • Câble d'alimentation SAS (à enficher sur le connecteur d'alimentation du fond de panier SAS) • Câble du commutateur d'intrusion du châssis • Câble d'interface SATA 8 Installez toutes les cartes d'extension. Voir “Installation d'une carte d'extension”, à la page 89.
Carte de distribution de l'alimentation Retrait de la carte de distribution de l'alimentation PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie.
Figure 3-35.
Installation de la carte de distribution de l'alimentation 1 Alignez les trois fentes de fixation de la carte de distribution de l'alimentation avec les trois pattes correspondantes situées au fond du châssis. Voir figure 3-35. 2 Fixez la carte à l'aide des sept vis. 3 Installez la carte système. Voir la procédure décrite de l'étape 4 à l'étape 14 dans la section “Installation de la carte système”. 4 Installez les blocs d'alimentation. Voir “Réinstallation d'un bloc d'alimentation”, à la page 82.
Figure 3-36.
Remplacement de la carte du module PEM 1 Installez la nouvelle carte du module PEM : a Faites descendre la carte dans le boîtier du module PEM. b Vérifiez que la carte est totalement parallèle avec le fond du boîtier du module PEM et que tous les crochets de fixation situés au fond du boîtier passent dans les fentes de fixation de la carte. Voir figure 3-34. c Poussez la carte vers l'arrière du boîtier jusqu'à ce que le plot de fixation bleu s'enclenche.
Installation des composants du système 159
Installation des composants du système
Dépannage du système La sécurité d'abord, pour vous et pour le système Pour effectuer certaines des procédures décrites ici, vous devez retirer le capot du système et intervenir à l'intérieur. Lorsque vous intervenez sur le système, suivez strictement les opérations décrites dans ce guide ou dans une autre documentation accompagnant le système. PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
Tableau 4-1. Indications fournies par la procédure de démarrage (suite) Symptôme Action Comportement du voyant d'activité du voir “Dépannage d'un périphérique lecteur de CD USB. USB”, à la page 167. Comportement du voyant d'activité du voir “Dépannage d'un lecteur optique”, lecteur de CD. à la page 178. Comportement du voyant d'activité du voir “Dépannage d'un disque dur”, disque dur. à la page 179. Un bruit inhabituel de raclement ou de voir “Obtention d'aide”, à la page 203.
Vérification du matériel Cette section contient les procédures de dépannage des périphériques externes directement connectés au système, comme le moniteur, le clavier ou la souris. Avant de suivre l'une de ces procédures, voir “Dépannage des connexions externes”, à la page 163.
3 Vérifiez si des moniteurs sont reliés à la fois au connecteur vidéo avant et au connecteur vidéo arrière du système Le système prend en charge un seul moniteur, qui doit être connecté soit à l'avant, soit à l'arrière du système. Si un moniteur est connecté au panneau avant, le connecteur vidéo arrière est désactivé. Si deux moniteurs sont reliés au système, déconnectez-en un. Si l'incident persiste, passez à l'étape suivante. 4 Exécutez le test de diagnostic en ligne approprié.
4 Si d'autres périphériques USB sont enfichés dans les ports situés près de ceux utilisés pour le clavier et la souris, éteignez ces périphériques et déconnectez-les du système. Si une surtension se produit sur un autre périphérique USB, le clavier et la souris peuvent cesser de fonctionner. Si le clavier et la souris ne fonctionnent toujours pas alors que vous avez déconnecté les autres périphériques USB, redémarrez le système. Si l'incident persiste, passez à l'étape suivante.
e Rebranchez le système sur la prise secteur, ainsi que les périphériques, puis redémarrez-le. Si le clavier et la souris fonctionnent correctement, passez à l'étape suivante. Si le clavier et la souris ne fonctionnent toujours pas correctement, voir “Obtention d'aide”, à la page 203. f Recommencez l'étape 2 et l'étape b. g Placez le cavalier NVRAM_CLR sur la position de désactivation. h Refermez le système.
Dépannage d'un périphérique d'E/S série Incident • Le périphérique connecté au port série ne fonctionne pas correctement. Action 1 Éteignez le système et les périphériques connectés au port série. 2 Remplacez le câble d'interface série par un câble fiable, puis allumez le système et le périphérique série. Si l'incident est résolu, remplacez le câble d'interface. 3 Éteignez le système et le périphérique série, puis remplacez ce dernier par un périphérique similaire.
c Éteignez le périphérique USB et remplacez son câble d'interface par un câble fiable. Allumez le périphérique. Si l'incident est résolu, remplacez le câble d'interface. d Éteignez le périphérique USB, branchez-le sur un autre port USB du système et rallumez-le. Si le périphérique USB fonctionne, le port USB du système est probablement défectueux. Sinon, le périphérique USB est défectueux et doit être remplacé. Voir “Obtention d'aide”, à la page 203.
e Rebranchez le système sur la prise secteur, ainsi que les périphériques, puis redémarrez-le. Si tous les périphériques USB sont opérationnels, passez à l'étape suivante. Si les périphériques USB ne fonctionnent toujours pas, voir “Obtention d'aide”, à la page 203. f Recommencez l'étape 2 et l'étape b. g Placez le cavalier NVRAM_CLR sur la position de désactivation. h Refermez le système. i Rebranchez le système sur la prise secteur, ainsi que les périphériques, puis redémarrez-le.
• Si possible, modifiez le paramétrage de négociation automatique. • Utilisez un autre connecteur sur le commutateur ou le concentrateur. Si vous utilisez une carte réseau au lieu d'un NIC intégré, consultez la documentation fournie avec celle-ci. 3 Vérifiez que les pilotes appropriés sont installés et que les protocoles sont liés. Consultez la documentation du NIC. 4 Accédez au programme de configuration du système et vérifiez que les interfaces réseau sont activées.
3 Retirez toutes les cartes d'extension du système. Voir “Retrait d'une carte d'extension”, à la page 91. 4 Laissez le système sécher complètement pendant au moins 24 heures. 5 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. 6 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. Si le système ne démarre pas normalement, voir “Obtention d'aide”, à la page 203.
• Processeurs et dissipateurs de chaleur • Barrettes de mémoire • Connexions des supports de lecteurs sur la carte de fond de panier 3 Vérifiez que tous les câbles sont correctement connectés. 4 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. 5 Lancez les tests System board (Carte système) des diagnostics du système. Voir “Utilisation de Dell PowerEdge Diagnostics”, à la page 189. Si les tests échouent, voir “Obtention d'aide”, à la page 203.
REMARQUE : Certains logiciels peuvent provoquer une accélération ou un ralentissement de l'heure système. Si le système semble fonctionner normalement à l'exception de l'heure qui est conservée dans le programme de configuration du système, l'incident peut être causé par un logiciel plutôt que par une pile défectueuse. Dépannage des blocs d'alimentation Incident • Les voyants d'état du système sont orange. • Les voyants de panne des blocs d'alimentation sont orange.
Dépannage des problèmes de refroidissement du système Incident • Le logiciel de gestion de systèmes a émis un message d'erreur concernant les ventilateurs. Action Vérifiez qu'aucune des conditions suivantes n'est présente : • Le capot du système, le protecteur de ventilation, un cache de lecteur ou une plaque de recouvrement avant ou arrière a été retiré. • La température ambiante est trop élevée. • La circulation de l'air extérieur est bloquée.
Action PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique. Les dommages causés par des interventions de maintenance non autorisées par Dell ne sont pas couverts par votre garantie. Consultez et respectez les consignes de sécurité livrées avec le produit.
Dépannage de la mémoire système Incident • Barrette de mémoire défectueuse. • Carte système défectueuse. • L'écran LCD du panneau avant indique qu'un incident lié à la mémoire système s'est produit. Action PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé. Vous devez uniquement procéder aux dépannages et réparations simples autorisés dans le manuel de votre produit, ou selon les directives du service et du support en ligne ou téléphonique.
6 Vérifiez les bancs de mémoire et assurez-vous que l'installation des barrettes de mémoire est correcte. Voir “Consignes générales pour l'installation des barrettes de mémoire”, à la page 105. Si les connecteurs mémoire sont remplis correctement, passez à l'étape suivante. 7 Remboîtez les barrettes de mémoire dans leurs supports. Voir “Installation de barrettes de mémoire”, à la page 109. 8 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75.
17 Si l'incident persiste, recommencez la procédure décrite de l'étape 11 à l'étape 16 pour chaque barrette installée. Si l'incident persiste alors que vous avez vérifié toutes les barrettes de mémoire, voir “Obtention d'aide”, à la page 203. Dépannage d'un lecteur optique Incident • Le système ne peut pas lire les données d'un CD ou d'un DVD placé dans le lecteur. • Le voyant du lecteur optique ne clignote pas au démarrage du système.
8 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. 9 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. Si l'incident persiste, voir “Obtention d'aide”, à la page 203. Dépannage d'un disque dur Incident • Erreur de pilote de périphérique. • Un ou plusieurs disques durs ne sont pas reconnus par le système. Action PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
5 Si le système contient une carte contrôleur RAID SAS, effectuez les opérations suivantes. a Redémarrez le système et appuyez sur pour ouvrir l'utilitaire de configuration de l'adaptateur hôte. Consultez la documentation fournie avec la carte contrôleur pour obtenir des informations sur cet utilitaire. b Assurez-vous que le disque dur a été configuré correctement. c Quittez l'utilitaire de configuration et laissez le système d'exploitation démarrer.
d Vérifiez que les câbles de données sont correctement emboîtés dans leurs connecteurs. e Vérifiez que le connecteur d'alimentation du fond de panier SAS est correctement emboîté dans son connecteur. f Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. g Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. Si l'incident persiste, voir “Obtention d'aide”, à la page 203.
3 Redémarrez le système et appuyez sur pour ouvrir l'utilitaire de configuration. Consultez la documentation du contrôleur pour obtenir des informations sur les paramètres de configuration. 4 Vérifiez les paramètres de configuration, corrigez-les au besoin et redémarrez le système. Si l'incident persiste, passez à l'étape suivante. 5 Éteignez le système et les périphériques connectés, puis débranchez-le de la prise secteur. 6 Ouvrez le système.
Dépannage d'un lecteur de bande SAS externe Incident • Lecteur de bande défectueux • Cartouche défectueuse • Logiciel de sauvegarde sur bande ou pilote du lecteur de bande manquant ou altéré • Contrôleur SAS défectueux Action 1 Retirez la cartouche que vous utilisiez lorsque l'incident s'est produit, et remplacez-la par une autre cartouche fiable. 2 Assurez-vous que les pilotes correspondant au lecteur de bande sont installés et configurés correctement.
10 Si l'incident persiste, consultez la documentation du lecteur de bande pour obtenir des instructions de dépannage supplémentaires. 11 Réinstallez le logiciel de sauvegarde sur bande en suivant les instructions de sa documentation. 12 Si vous ne parvenez pas à résoudre l'incident, voir “Obtention d'aide”, à la page 203. Dépannage des cartes d'extension REMARQUE : Pour dépanner une carte d'extension, reportez-vous également à sa documentation et à celle du système d'exploitation.
Si l'incident persiste, passez à l'étape suivante. 7 Éteignez le système et les périphériques connectés, puis débranchez-le de la prise secteur. 8 Ouvrez le système. Voir “Ouverture et fermeture du système”, à la page 75. 9 Retirez toutes les cartes d'extension du système. Voir “Retrait d'une carte d'extension”, à la page 91. 10 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. 11 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés.
Dépannage des microprocesseurs Incident • Un message d'erreur signale un incident lié au processeur. • L'écran LCD du panneau avant indique qu'un incident lié aux processeurs ou à la carte système s'est produit. • Un dissipateur de chaleur n'est pas installé pour chaque processeur. Action PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
9 Ouvrez le système. Voir “Ouverture et fermeture du système”, à la page 75. 10 Remplacez le processeur 1 par un autre de même type. Voir “Retrait d'un processeur”, à la page 113 et “Installation d'un processeur”, à la page 116. 11 Refermez le système. Voir “Ouverture et fermeture du système”, à la page 75. 12 Exécutez le test de diagnostic en ligne approprié. Si les tests réussissent, remplacez le processeur 1. Voir “Obtention d'aide”, à la page 203.
Dépannage du système
Exécution des diagnostics du système Si vous rencontrez des difficultés lors de l'utilisation du système, lancez les diagnostics avant de demander une assistance technique. Le but des diagnostics est de tester le matériel du système sans nécessiter d'équipement supplémentaire et sans risque de perte de données. Si vous ne réussissez pas à corriger le problème, le personnel de service et de support peut s'aider des résultats des tests de diagnostic.
• Interrompre temporairement un test quand une erreur est détectée ou l'arrêter lorsqu'une limite d'erreur définie par l'utilisateur est atteinte. • Afficher des messages d'aide qui décrivent brièvement chaque test et ses paramètres. • Afficher des messages d'état qui vous indiquent si les tests ont abouti. • Afficher des messages d'erreur qui vous indiquent si des incidents sont survenus pendant les tests.
Options de test des diagnostics du système Cliquez sur l'option de test voulue dans la fenêtre Main Menu (Menu principal). Le Tableau 5-1 contient une brève explication sur les options de test disponibles. Tableau 5-1. Options de test des diagnostics du système Option de test Fonction Express Test (Test rapide) Effectue une vérification rapide du système. Cette option exécute les tests de périphériques qui ne requièrent pas d'action de l'utilisateur.
Sélection d'options de diagnostic Le champ Diagnostics Options (Options de diagnostic) permet de sélectionner la façon dont le périphérique sera testé. Vous pouvez définir les options suivantes : • Non-Interactive Tests Only (Tests non-interactifs uniquement) : cette option permet d'exécuter uniquement les tests ne nécessitant aucune intervention de l'utilisateur. • Quick Tests Only (Tests rapides uniquement) : cette option permet d'exécuter uniquement les tests rapides sur le périphérique sélectionné.
Cavaliers et connecteurs Cette section contient des informations spécifiques sur les cavaliers du système. Elle contient également des informations générales sur les cavaliers et les commutateurs et décrit les connecteurs des différentes cartes du système. Cavaliers de la carte système La figure 6-1 présente l'emplacement des cavaliers de configuration sur la carte système. Le Tableau 6-1 répertorie les réglages des cavaliers. Tableau 6-1.
Désactivation d'un mot de passe oublié Les fonctionnalités logicielles de protection du système comprennent un mot de passe système et un mot de passe de configuration, qui sont présentés en détail dans la section “Utilisation du programme de configuration du système”, à la page 49. Le cavalier de mot de passe active ces fonctions ou les désactive, et efface le(s) mot(s) de passe utilisé(s). PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de service agréé.
6 Éteignez le système et les périphériques connectés, puis débranchez-le de la prise secteur. 7 Ouvrez le système. Voir “Ouverture et fermeture du système”, à la page 75. 8 Déplacez le cavalier du mot de passe sur les broches 4-6 pour restaurer la protection par mot de passe. 9 Refermez le système. 10 Rebranchez le système et les périphériques sur les prises secteur, puis allumez le système. 11 Attribuez un nouveau mot de passe système et/ou de configuration.
Figure 6-1.
Tableau 6-2.
Connecteurs de la carte du module d'extension processeurs voir figure 6-2 et Tableau 6-3 pour obtenir la description et l'emplacement des connecteurs situés sur la carte du module PEM. Figure 6-2. Connecteurs de la carte du module d'extension processeurs 2 1 5 Tableau 6-3.
Connecteurs de la carte de fond de panier SAS La figure 6-3 montre l'emplacement des connecteurs sur la carte de fond de panier. Figure 6-3.
Figure 6-4.
Carte adaptatrice SAS 2,5 pouces pour les périphériques En plus du fond de panier, les systèmes équipés de lecteurs 2,5 pouces sont dotés d'une carte adaptatrice pour les périphériques. Figure 6-5.
Cavaliers et connecteurs
Obtention d'aide Contacter Dell Aux États-Unis, appelez le 800-WWW-DELL (800-999-3355). REMARQUE : Si vous ne disposez pas d'une connexion Internet active, vous pouvez utiliser les coordonnées figurant sur votre preuve d'achat, votre bordereau de livraison, votre facture ou encore sur le catalogue des produits Dell. Dell fournit plusieurs options de service et de support en ligne et par téléphone.
Obtention d'aide
Glossaire Cette section définit ou identifie les termes techniques, abréviations et sigles utilisés dans la documentation fournie avec le système. A : Ampère(s). ACPI : Acronyme de “Advanced Configuration and Power Interface”. Interface standard qui permet au système d'exploitation de contrôler les paramètres relatifs à la configuration et à la gestion de l'alimentation. adaptateur hôte : Carte assurant la communication entre le bus du système et le contrôleur d'un périphérique.
bus : Chemin d'informations entre les différents composants du système. Le système contient un bus d'extension qui permet au processeur de communiquer avec les contrôleurs des différents périphériques connectés au système. Il contient également un bus d'adresse et un bus de données pour les communications entre le microprocesseur et la RAM. bus d'extension : Votre système contient un bus d'extension qui permet au processeur de communiquer avec les contrôleurs des périphériques (NIC, etc.).
combinaison de touches : Commande exécutée lorsque l'utilisateur appuie sur plusieurs touches en même temps (exemple : ). composant : Dans le contexte de l'interface DMI, un composant est un élément compatible DMI, comme un système d'exploitation, un ordinateur, une carte d'extension ou un périphérique. Chaque composant est constitué de groupes et d'attributs définis comme caractéristiques de ce composant.
DNS : Acronyme de “Domain Name System”, système de noms de domaines. Méthode de conversion des noms de domaines Internet (par exemple www.dell.com) en adresses IP (par exemple 143.166.83.200). DRAM : Acronyme de “Dynamic Random-Access Memory”, mémoire vive dynamique. Normalement, la mémoire vive d'un système est composée entièrement de puces DRAM. DVD : Acronyme de “Digital Versatile Disc”, disque numérique polyvalent. E/S : Entrée/sortie.
G : Gravité. Gb : Gigabit(s) ; 1 024 mégabits, soit 1 073 741 824 bits. Go : Giga-octet(s) ; 1 024 méga-octets, soit 1 073 741 824 octets. La mesure est souvent arrondie à 1 000 000 000 octets lorsqu'elle fait référence à la capacité d'un disque dur. groupe : Dans le contexte de l'interface DMI, un groupe est une structure de données qui définit les informations courantes, ou attributs, d'un composant gérable.
Ko/s : Kilo-octets par seconde. KVM : Acronyme de “Keyboard/Video/Mouse”, ensemble clavier/moniteur/souris. Le terme KVM désigne un commutateur qui permet de sélectionner le système correspondant à la sortie vidéo affichée et auquel s'applique l'utilisation du clavier et de la souris. lame : Module équipé d'un processeur, de mémoire et d'un disque dur. Ces modules sont montés dans une baie qui dispose d'alimentations et de ventilateurs. LAN : Acronyme de “Local Area Network”, réseau local.
mémoire flash : Type de puce EEPROM pouvant être reprogrammée à partir d'un utilitaire stocké sur disquette alors qu'elle est en place dans le système. La plupart des puces EEPROM ne peuvent être reprogrammées qu'avec un équipement de programmation spécial. mémoire système : voir RAM. mémoire vidéo : La plupart des cartes vidéo VGA et SVGA contiennent des puces de mémoire qui viennent s'ajouter à la RAM du système.
NIC : Acronyme de “Network Interface Controller”. Dispositif intégré ou installé sur un système afin de permettre sa connexion à un réseau. NMI : Acronyme de “NonMaskable Interrupt”, interruption non masquable. Un matériel envoie une NMI pour signaler des erreurs matérielles au processeur. ns : Nanoseconde(s). NTFS : Option du système de fichiers NT dans le système d'exploitation Windows 2000.
pilote de périphérique : Programme qui permet au système d'exploitation ou à un autre programme de communiquer correctement avec un périphérique ou un matériel donné. Certains pilotes de périphériques, comme les pilotes réseau, doivent être chargés par le fichier config.sys ou en tant que programmes résidant en mémoire (en général par le fichier autoexec.bat). D'autres, comme le pilote vidéo, se chargent lorsque vous démarrez le programme pour lequel ils sont conçus.
RAM : Acronyme de “Random-Access Memory”, mémoire vive. Zone principale de stockage temporaire du système pour les instructions d'un programme et les données. Toutes les informations stockées dans la RAM sont perdues lorsque vous éteignez le système. RAS : Acronyme de “Remote Access Service”, service d'accès à distance. Sous Microsoft Windows, ce service permet d'accéder à un réseau distant à l'aide d'un modem.
sauvegarde : Copie d'un programme ou de données. Par précaution, il convient de sauvegarder régulièrement le disque dur du système. Avant de modifier la configuration du système, il est conseillé de sauvegarder les fichiers de démarrage importants du système d'exploitation. SCSI : Acronyme de “Small Computer System Interface”, interface pour petits systèmes informatiques. Interface de bus d'E/S autorisant des transmissions de données plus rapides que les ports standard.
système “sans tête” : Système ou périphérique qui fonctionne sans moniteur, souris ni clavier. Habituellement, les systèmes sans tête sont gérés via un réseau à l'aide d'un navigateur Internet. TCP/IP : Acronyme de “Transmission Control Protocol/Internet Protocol”. température ambiante : Température de l'endroit ou de la pièce où se trouve le système.
win.ini : Fichier de démarrage du système d'exploitation Windows. Au démarrage de Windows, le système d'exploitation consulte le fichier win.ini afin de déterminer les options à utiliser dans l'environnement Windows. Ce fichier comprend généralement aussi des sections qui contiennent les paramètres facultatifs pour les programmes Windows installés sur le disque dur.
Glossaire
Index A C Alerte, messages, 47 Cache de lecteur Installation, 123 Retrait, 122 Assemblage du panneau de commande Installation, 136 Retrait, 133 Avertissement, messages, 47 B Barrettes de mémoire (DIMM) Configuration, 105 Dépannage, 176 Installation, 109 Retrait, 111 Batterie (RAID) Dépannage, 181 Installation, 129 Cadre, 74 Capot Fermeture, 77 Ouverture, 75 Carte adaptatrice pour les ventilateurs Installation, 148 Retrait, 146 Carte contrôleur SAS Installation, 127 Retrait, 127 Batterie RAID, 129 Ca
Installation, 101 Retrait, 104 Carte SD Installation, 101 Carte système Cavaliers, 193 Connecteurs, 195 Installation, 152, 158 Retrait, 149 Cartes d'extension Contrôleur SAS, 127 Dépannage, 184 Installation, 89 Retrait, 91 Cavaliers (carte système), 193 Clavier Dépannage, 164 Commutateur d'intrusion du châssis Installation, 137 Retrait, 136 Connecteurs Carte de fond de panier SAS, 199 Carte système, 195 Module PEM, 198 Panneau arrière, 19 Panneau avant, 14 Consignes Installation de cartes d'extension, 87 In
Périphériques intégrés, 57 Sécurité du système, 60 Système endommagé, 171 Système mouillé, 170 Ventilateurs, 174 Vidéo, 163 Diagnostics Contexte d'utilisation, 190 messages, 47 Options de test, 191 Options de test avancées, 191 I Dissipateur de chaleur, 114 Installation, 114 Assemblage du panneau de commande, 136 Barrettes de mémoire, 109 Batterie RAID, 129 Cache de disque dur, 123 Carte adaptatrice pour les ventilateurs, 148 Carte d'extension, 89 Carte de distribution de l'alimentation, 156 Carte de fo
Voir Lecteur optique. Lecteur optique Dépannage, 178 Installation, 118 Support de lecteur, 118-119 Logements Voir Logements d'extension.
Réinstallation, 81 Retrait, 79 P Panneau arrière, caractéristiques, 18 Panneau avant, caractéristiques, 14 Périphérique d'amorçage Configuration, 122 Périphérique d'E/S série Dépannage, 167 Périphérique de stockage Fibre Channel, 130 Périphérique USB Connecteurs du panneau arrière, 18 Connecteurs du panneau avant, 14 Dépannage, 167 Pile du système Dépannage, 172 Remplacement, 131 PowerNow!, 57 Processeur Dépannage, 186 Installation, 115 Remplacement, 113 Programme de configuration du système Accès, 49 Opti
Disques durs, 123 Module PEM, 83 Protecteur de ventilation, 79 Ventilateur, 77 S Sécurité, 161 Support Contacter Dell, 203 Support de lecteur Disque dur, 124 Lecteur optique, 118 Support ZIF, 113 Système Fermeture, 77 Ouverture, 75 Système mouillé Dépannage, 170 Système, messages, 37 T Touches Démarrage, 12 Fonctions de la carte RAC, 13 Programme de configuration du système, 49 Touches accessibles pendant l'auto-test de démarrage, 12 224 Index V Ventilateur Dépannage, 174 Réinstallation, 79 Retrait, 77