Owner's Manual
Table Of Contents
- Dell PowerEdge R920 System Owner's Manual
- About Your System
- Using The System Setup and Boot Manager
- Installing System Components
- Recommended Tools
- Front Bezel (Optional)
- Opening And Closing The System
- Inside The System
- Cable Management Tray
- System Memory
- General Memory Module Installation Guidelines
- Mode-Specific Guidelines
- Advanced ECC (Lockstep)
- Memory Optimized (Independent Channel) Mode
- Memory Sparing
- Memory Mirroring
- Fault Resilient Memory
- Sample Memory Configurations
- Removing A Memory-Riser Blank
- Installing A Memory-Riser Blank
- Removing A Memory Riser
- Installing A Memory Riser
- Removing Memory Modules From The Memory Riser
- Installing Memory Modules
- Memory Riser And Fan Cage
- Hard Drives
- Optical Drive (Optional)
- Cooling Fans
- Internal USB Memory Key (Optional)
- Expansion Cards And Expansion-Card Risers
- Expansion Card Installation Guidelines
- Removing The Left Expansion Card Riser Blank
- Installing The Left Expansion Card Riser Blank
- Removing The Right Expansion Card Riser Blank
- Removing An Expansion Card From Expansion-Card Risers 2 and 3
- Installing An Expansion Card Into The Expansion-Card Riser 2 and 3
- NDC Riser (I/O Riser 1)
- Network Daughter Card
- SD vFlash Card
- Internal Dual SD Module
- Internal SD Card
- Integrated Storage Controller Card
- RAID Battery
- Processors
- Power Supplies
- Hot Spare Feature
- Removing An AC Power Supply
- Installing An AC Power Supply
- Wiring Instructions For A DC Power Supply
- Assembling And Connecting The Safety Ground Wire
- Assembling The DC Input Power Wires
- Removing A DC Power Supply
- Installing A DC Power Supply
- Removing The Power Supply Blank
- Installing The Power Supply Blank
- Power Distribution Board
- System Battery
- Hard-Drive Backplane
- SAS Expander Daughter Card
- Control Panel Board
- System Board
- Troubleshooting Your System
- Safety First—For You And Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting The Video Subsystem
- Troubleshooting A USB Device
- Troubleshooting A Serial I/O Device
- Troubleshooting A Wet System
- Troubleshooting A Damaged System
- Troubleshooting The System Battery
- Troubleshooting Power Supplies
- Troubleshooting Cooling Problems
- Troubleshooting Cooling Fans
- Troubleshooting System Memory
- Troubleshooting An Internal USB Key
- Troubleshooting An SD Card
- Troubleshooting An Optical Drive
- Troubleshooting A Hard Drive
- Troubleshooting A Storage Controller
- Troubleshooting Expansion Cards
- Troubleshooting Processors
- Using System Diagnostics
- Jumpers And Connectors
- Technical Specifications
- System Messages
- Getting Help
3. Disconnect the cables connected to the control panel board.
NOTE: Note the routing of the cables on the side of the system as you remove them from the control panel
board. You must route these cables properly when you replace them inside the shim stock pieces to prevent
them from being pinched or crimped.
4. Using a Phillips screwdriver, remove the two screws that secure the control panel board to the chassis.
5. Slide the control panel board toward the back of the system and remove.
Figure 67. Removing and Installing the Control Panel Board
1. screw securing the control panel board (2) 2. control panel connector cable
3. display module cable 4. USB connector cable
5. control panel board
Installing The Control Panel Board
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1. Align the screw holes on the control panel board with the holes on the chassis.
2. Using a Phillips driver, tighten the screws that secure the control panel board to the chassis.
111