Owner's Manual
Table Of Contents
- Dell PowerEdge R920 System Owner's Manual
- About Your System
- Using The System Setup and Boot Manager
- Installing System Components
- Recommended Tools
- Front Bezel (Optional)
- Opening And Closing The System
- Inside The System
- Cable Management Tray
- System Memory
- General Memory Module Installation Guidelines
- Mode-Specific Guidelines
- Advanced ECC (Lockstep)
- Memory Optimized (Independent Channel) Mode
- Memory Sparing
- Memory Mirroring
- Fault Resilient Memory
- Sample Memory Configurations
- Removing A Memory-Riser Blank
- Installing A Memory-Riser Blank
- Removing A Memory Riser
- Installing A Memory Riser
- Removing Memory Modules From The Memory Riser
- Installing Memory Modules
- Memory Riser And Fan Cage
- Hard Drives
- Optical Drive (Optional)
- Cooling Fans
- Internal USB Memory Key (Optional)
- Expansion Cards And Expansion-Card Risers
- Expansion Card Installation Guidelines
- Removing The Left Expansion Card Riser Blank
- Installing The Left Expansion Card Riser Blank
- Removing The Right Expansion Card Riser Blank
- Removing An Expansion Card From Expansion-Card Risers 2 and 3
- Installing An Expansion Card Into The Expansion-Card Riser 2 and 3
- NDC Riser (I/O Riser 1)
- Network Daughter Card
- SD vFlash Card
- Internal Dual SD Module
- Internal SD Card
- Integrated Storage Controller Card
- RAID Battery
- Processors
- Power Supplies
- Hot Spare Feature
- Removing An AC Power Supply
- Installing An AC Power Supply
- Wiring Instructions For A DC Power Supply
- Assembling And Connecting The Safety Ground Wire
- Assembling The DC Input Power Wires
- Removing A DC Power Supply
- Installing A DC Power Supply
- Removing The Power Supply Blank
- Installing The Power Supply Blank
- Power Distribution Board
- System Battery
- Hard-Drive Backplane
- SAS Expander Daughter Card
- Control Panel Board
- System Board
- Troubleshooting Your System
- Safety First—For You And Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting The Video Subsystem
- Troubleshooting A USB Device
- Troubleshooting A Serial I/O Device
- Troubleshooting A Wet System
- Troubleshooting A Damaged System
- Troubleshooting The System Battery
- Troubleshooting Power Supplies
- Troubleshooting Cooling Problems
- Troubleshooting Cooling Fans
- Troubleshooting System Memory
- Troubleshooting An Internal USB Key
- Troubleshooting An SD Card
- Troubleshooting An Optical Drive
- Troubleshooting A Hard Drive
- Troubleshooting A Storage Controller
- Troubleshooting Expansion Cards
- Troubleshooting Processors
- Using System Diagnostics
- Jumpers And Connectors
- Technical Specifications
- System Messages
- Getting Help
Installing The RAID Battery
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
2. Open the system.
3. Remove the storage controller card.
4. Connect the RAID battery cable connector on the storage controller card.
5. Align the RAID battery module (battery and carrier) with the slots on the storage controller card.
6. Push the battery module into the slots, so that it snaps in place.
7. Connect the SAS data cables to the data cable connectors on the integrated storage controller card.
8. Insert the storage controller card into the connector on system board.
9. Close the system.
10. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.
Processors
Use the following procedure when:
• Installing an additional processor
• Replacing a processor
Your system supports two types of processor configurations:
• Four-processor configuration
• Two-processor configuration
NOTE: To ensure proper system cooling, you must install a processor blank and a heat-sink blank in any empty
processor socket.
Removing A Heat Sink Blank
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
2. Open the system.
3. Remove the following:
a) memory risers
b) cooling fans
c) memory riser and fan cage
d) cable management tray
e) fan tray
4. Locate the heat sink blank seated on the processor blank.
82