Owners Manual
Table Of Contents
- Dell PowerEdge R930 Owner's Manual
- Contents
- About the PowerEdge R930
- Documentation resources
- Technical specifications
- Initial system setup and configuration
- Pre-operating system management applications
- Options to manage the pre-operating system applications
- System Setup
- Viewing System Setup
- System Setup details
- System BIOS
- Viewing System BIOS
- System BIOS Settings details
- Boot Settings
- Network Settings
- System Security
- System Information
- Memory Settings
- Processor Settings
- SATA Settings
- Integrated Devices
- Serial Communication
- System Profile Settings
- Miscellaneous Settings
- iDRAC Settings utility
- Device Settings
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Front bezel (optional)
- System cover
- Inside the system
- System memory
- Memory riser
- Memory riser and fan cage
- Cooling fans
- Cable management tray
- Hard drives
- Optical drive (optional)
- Internal USB memory key (optional)
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the left or right expansion card riser blank
- Installing the left or right expansion card riser blank
- Removing the left or right expansion card riser
- Installing the left or right expansion card riser
- Removing an expansion card from expansion card risers
- Installing an expansion card into the expansion card risers
- Network Daughter Card riser
- Network daughter card
- Chassis intrusion switch
- SD vFlash card (optional)
- Internal dual SD module (optional)
- Integrated storage controller card
- Processors and heat sinks
- Power supply units
- Power distribution board
- System battery
- Hard drive backplane
- SAS expander daughter card
- Control panel
- System board
- Trusted Platform Module
- Troubleshooting your system
- Troubleshooting system startup failure
- Troubleshooting external connections
- Troubleshooting the video subsystem
- Troubleshooting a USB device
- Troubleshooting a serial input and output device
- Troubleshooting a NIC
- Troubleshooting a wet system
- Troubleshooting a damaged system
- Troubleshooting the system battery
- Troubleshooting power supply units
- Troubleshooting cooling problems
- Troubleshooting cooling fans
- Troubleshooting system memory
- Troubleshooting an internal USB key
- Troubleshooting a micro SD card
- Troubleshooting an optical drive
- Troubleshooting a drive or SSD
- Troubleshooting a storage controller
- Troubleshooting expansion cards
- Troubleshooting processors
- Using system diagnostics
- Jumpers and connectors
- Getting help
Table 3. Back panel features of the PowerEdge R930 system
Item Indicator, Button, or
Connector
Icon Description
● Two 100 Mbps/1 Gbps/10 Gbps and two SFP+/10 GbE T
connectors
● Four SFP+/10 GbE T connectors
7 USB port (2)
The USB ports are 4-pin, 2.0-compliant. These ports enable
you to connect USB devices to the system.
8 Serial port
Enables you to connect a serial device to the system. For
more information, see the Technical specifications section.
9 System identification port
The System identification port connects the optional system
status indicator assembly to the system through the optional
cable management arm.
10 System identification button
NOTE: To reset the iDRAC (if not disabled in System
Setup), press and hold the button for more than 15
seconds.
Diagnostic indicators
The diagnostic indicators on the system indicate operation and error status.
Hard drive indicator codes
Each hard drive carrier has an activity indicator and a status indicator. The indicators provide information about the current
status of the hard drive. The activity LED indicates whether hard drive is currently in use or not. The status LED indicates the
power condition of the hard drive.
Figure 5. Hard drive indicators
1. Hard drive activity indicator
2. Hard drive status indicator
3. Hard drive
About the PowerEdge R930
15