Dell EMC PowerEdge R940xa Installations- und Service-Handbuch Vorschriftenmodell: E54S Series Vorschriftentyp: E54S001 Juni 2021 Rev.
Hinweise, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS warnt vor möglichen Beschädigungen der Hardware oder vor Datenverlust und zeigt, wie diese vermieden werden können. WARNUNG: Mit WARNUNG wird auf eine potenziell gefährliche Situation hingewiesen, die zu Sachschäden, Verletzungen oder zum Tod führen kann. © 2019– 2021 Dell Inc. oder ihre Tochtergesellschaften.
Inhaltsverzeichnis Kapitel 1: Über dieses Dokument.......................................................................................................7 Kapitel 2: Übersicht des PowerEdge R940xa-Systems....................................................................... 8 Frontansicht des Systems.................................................................................................................................................... 8 Bedienfelder...............................................
Einsetzen eines Kühlungslüfters.................................................................................................................................. 37 Lüfterbaugruppe..................................................................................................................................................................38 Entfernen der Lüfterbaugruppe...................................................................................................................................
M.2-SSD-Modul..................................................................................................................................................................118 Entfernen des M.2-BOSS-Moduls..............................................................................................................................118 Installieren des M.2-BOSS-Moduls.............................................................................................................................
Integrierte Dell Systemdiagnose.................................................................................................................................150 Kapitel 7: Wie Sie Hilfe bekommen................................................................................................ 152 Kontaktaufnahme mit Dell................................................................................................................................................ 152 Feedback zur Dokumentation...............
1 Über dieses Dokument Dieses Dokument bietet eine Übersicht über das System, Informationen zur Installation und zum Austausch von Komponenten, zu technischen Daten und zu Diagnosetools sowie Richtlinien, die bei der Installation bestimmter Komponenten zu beachten sind.
2 Übersicht des PowerEdge R940xa-Systems Das PowerEdge R940xa-System ist ein 4HE-Rack-Server, der maximal Folgendes unterstützt: ● Vier Intel Xeon-Prozessoren der skalierbaren Reihe ● 48 DIMM-Steckplätze ● Vier Wechselstrom- oder Gleichstrom-Stromversorgungseinheiten mit 2+2-Redundanz, automatischer Erkennung und AutoswitchingFunktion. ● 32 x 2,5-Zoll-SAS/SATA-HDD/SSDs, einschließlich 4 NVMe-SSDs.
Bedienfelder Ansicht des linken Bedienfelds Abbildung 2. Ansicht des linken Bedienfelds 1. Status-LEDs 2. Systemzustands- und System-ID-Anzeige 3. iDRAC Quick Sync 2 Wireless-Anzeige (optional) Ansicht des rechten Bedienfelds Abbildung 3. Ansicht des rechten Bedienfelds 1. 2. 3. 4. 5. Netzschalter USB 2.0-Anschluss (2) iDRAC Direct-Port iDRAC Direct-LED VGA-Port ANMERKUNG: Weitere Informationen finden Sie in den technischen Daten des Dell EMC PowerEdge R940xa auf der Seite mit der Produktdokumentation.
● Wenn das System Aufmerksamkeit erfordert, leuchtet die LCD-Anzeige gelb und es wird ein entsprechender Fehlercode mit Beschreibung angezeigt. ANMERKUNG: Wenn das System an eine Stromquelle angeschlossen ist und ein Fehler festgestellt wurde, leuchtet die LCDAnzeige gelb, unabhängig davon, ob das System eingeschaltet ist oder nicht. ● Wenn das System ausgeschaltet wird und keine Fehler vorliegen, wechselt das LCD nach fünf Minuten ohne Benutzereingabe in den Stand-by-Modus.
Option Beschreibung iDRAC Wählen Sie DHCP oder Statische IP aus, um den Netzwerkmodus zu konfigurieren. Wenn Static IP ausgewählt ist, sind die verfügbaren Felder IP, Subnet (Sub) und Gateway (Gtw). Wählen Sie DNS einrichten aus, um DNS zu aktivieren und Domänenadressen anzuzeigen. Zwei separate DNS-Einträge sind verfügbar. Set error (Fehler einstellen) Wählen Sie SEL aus, um LCD-Fehlermeldungen in einem Format entsprechend der IPMI-Beschreibung im SEL anzuzeigen.
Rückansicht des Systems Abbildung 5. Rückansicht des Systems 1. 3. 5. 7. 9. 11. Erweiterungs-Riser mit voller Höhe 1 Netzteile (4) Kabelanschluss für Systemstatusanzeige (Kabelführungsarm) USB 3.0-Anschlüsse (2) Serielle Schnittstelle NIC-Ports (4) 2. 4. 6. 8. 10.
Das Systeminnere Abbildung 6. Das Systeminnere 1. 2. 3. 4. 5. Laufwerks-Rückwandplatine Lüfterbaugruppe Systemplatine Riser 2 Riser 1 Ausfindigmachen des Informationsanhängers für Ihr System Sie können Ihr System anhand des eindeutigen Express-Servicecodes und der Service-Tag-Nummer identifizieren. Ziehen Sie den Informationsanhänger an der Vorderseite des Systems heraus, um den Express-Servicecode und die Service-Tag-Nummer sehen zu können.
3. OpenManage Mobile (OMM)-Etikett 4. Etikett mit iDRAC-MAC-Adresse und sicherem iDRAC-Kennwort ANMERKUNG: Wenn Sie sich für den sicheren Standardzugriff auf iDRAC entschieden haben, ist das sichere iDRACStandardkennwort auf der Rückseite des Systeminformationsanhängers vermerkt. Diese Kennzeichnung ist leer, falls sie sich nicht für den sicheren Standardzugriff auf iDRAC entschieden haben, und der Standardbenutzername und das Standardkennwort lauten dann root und calvin. 5.
Abbildung 9. Konfiguration und Layout Abbildung 10.
Abbildung 11. Symbollegende PowerEdge R940xa – Serviceinformationen Abbildung 12.
Abbildung 13. Rückansicht der Konfiguration Abbildung 14.
Abbildung 15. Informationen zum Arbeitsspeicher Abbildung 16. Systemaufgaben Abbildung 17.
Abbildung 18.
3 Anfängliche Systemeinrichtung und Erstkonfiguration Themen: • • • Einrichten des Systems iDRAC-Konfiguration Optionen zum Installieren des Betriebssystems Einrichten des Systems Führen Sie die folgenden Schritte aus, um das System einzurichten: Schritte 1. Packen Sie das System aus. 2. Installieren Sie das System im Rack. Weitere Informationen zum Einsetzen des Systems in das Rack finden Sie im Schieneninstallationshandbuch unter www.dell.com/poweredgemanuals. 3.
Schnittstellen Dokument/Abschnitt Dell Lifecycle Controller Benutzerhandbuch für den Dell Lifecycle Controller unter www.dell.com/poweredgemanuals Server-LCDDisplay Abschnitt LCD-Display iDRAC Direct und Quick Sync 2 (optional) Siehe Benutzerhandbuch zum Integrated Dell Remote Access Controller unter www.dell.com/poweredgemanuals ANMERKUNG: Für den Zugriff auf iDRAC, stellen Sie sicher, dass Sie das Ethernet-Kabel an den dedizierten iDRAC9Netzwerkanschluss anschließen.
Tabelle 3. Firmware und Treiber Methoden Speicherort Über die Dell EMC Support-Website www.dell.com/support/home Verwendung von Dell Remote Access Controller Lifecycle Controller (iDRAC mit LC) www.dell.com/idracmanuals Verwendung von Dell Repository Manager (DRM) www.dell.com/openmanagemanuals > Repository Manager Verwendung von Dell OpenManage Enterprise www.dell.com/openmanagemanuals > OpenManage Essentials Verwendung von Dell OpenManage Enterprise www.dell.
4 Installieren und Entfernen von Systemkomponenten VORSICHT: Manche Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Maßnahmen zur Fehlerbehebung oder einfache Reparaturen sollten Sie nur dann selbst durchführen, wenn dies laut Produktdokumentation genehmigt ist, oder wenn Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsarbeiten werden durch die Garantie nicht abgedeckt.
VORSICHT: Manche Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Maßnahmen zur Fehlerbehebung oder einfache Reparaturen sollten Sie nur dann selbst durchführen, wenn dies laut Produktdokumentation genehmigt ist, oder wenn Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsarbeiten werden durch die Garantie nicht abgedeckt. Lesen und befolgen Sie die mit dem Produkt gelieferten Sicherheitshinweise.
● Erdungsband Frontblende Ein Schloss an der Blende dient zum Schutz vor unbefugtem Zugriff auf die Laufwerke. Der Systemstatus kann auf der Blende mit dem LCD-Display angezeigt werden. Weitere Informationen finden Sie unter LCD-Display. Entfernen der optionalen Frontverkleidung (Blende) Voraussetzungen Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Schritte 1. Entriegeln Sie die Frontverkleidung mit dem zugehörigen Schlüssel. 2.
2. Machen Sie den Schlüssel der Frontverkleidung ausfindig und entfernen Sie ihn. ANMERKUNG: Der Blendenschlüssel ist Teil der optionalen Frontverkleidung. Schritte 1. Richten Sie das rechte Ende der Frontverkleidung am System aus und setzen Sie sie ein. 2. Drücken Sie auf die Entriegelungstaste und bringen Sie das linke Ende der Frontverkleidung am System an. 3. Verriegeln Sie die Verkleidung (Blende) mit dem Schlüssel. Abbildung 20.
● System mit 32 Laufwerken - Bis zu 24 vorne zugängliche 2,5-Zoll-Laufwerke (SAS, SATA oder Nearline-SAS) einschließlich vier NVMe-Laufwerke in den Steckplätzen 0 bis 23 des oberen Laufwerkschachts und bis zu acht vorne zugängliche 2,5-Zoll-Laufwerke (SAS, SATA oder Nearline-SAS) in den Steckplätzen 24 bis 31 des unteren Laufwerkschachts. Entfernen eines Laufwerkplatzhalters Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2.
Abbildung 22. Einsetzen des Laufwerkplatzhalters Nächste Schritte 1. Bringen Sie die Frontblende wieder an. Entfernen eines Laufwerksträgers Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. 3. Bereiten Sie das Laufwerk mit der Verwaltungssoftware für das Entfernen vor. Wenn das Laufwerk online ist, blinkt die grüne Aktivitäts-/Fehleranzeige, während das Laufwerk ausgeschaltet wird.
Abbildung 23. Entfernen eines Laufwerksträgers Nächste Schritte 1. Setzen Sie den Laufwerksträger oder einen Laufwerkplatzhalter ein. Installieren des Laufwerksträgers Voraussetzungen VORSICHT: Bevor Sie bei laufendem System ein Laufwerk entfernen oder installieren, vergewissern Sie sich in der Dokumentation zur Speichercontrollerkarte, dass der Hostadapter korrekt für das Entfernen und Einsetzen von Laufwerken konfiguriert ist.
Schritte 1. Schieben Sie den Laufwerksträger in den Laufwerkssteckplatz, bis das Laufwerk in der Rückwandplatine einrastet. ANMERKUNG: Um den Bügel zu öffnen, drücken Sie auf die Freigabetaste auf der Vorderseite des Laufwerksträgers. 2. Schließen Sie den Bügel des Laufwerkträgers, um das Laufwerk zu verriegeln. Abbildung 24. Installieren des Laufwerksträgers Nächste Schritte 1. Bringen Sie die Frontblende wieder an. Laufwerk aus Laufwerkträger entfernen Voraussetzungen 1.
Abbildung 25. Laufwerk aus Laufwerkträger entfernen Nächste Schritte 1. Setzen Sie das Laufwerk wieder in den Laufwerkträger ein. Einsetzen des Laufwerks in den Laufwerkträger Voraussetzungen 1. Entfernen Sie die Frontblende. ANMERKUNG: Stellen Sie beim Einsetzen eines Laufwerks in den Laufwerkträger sicher, dass die Schrauben mit einem Anzugsmoment von 4 in-lbs angezogen werden. Schritte 1.
Abbildung 26. Einsetzen eines Laufwerks in den Laufwerkträger Nächste Schritte 1. Bringen Sie die Frontverkleidung wieder an. Systemabdeckung Die Systemabdeckung bietet Sicherheit für das gesamte System und unterstützt außerdem die Aufrechterhaltung eines ausreichenden Luftstroms im Inneren des Systems. Entfernen der Systemabdeckung Voraussetzungen 1. Befolgen Sie die Hinweise, die im Abschnitt Sicherheitshinweise aufgeführt sind. 2. Schalten Sie das System und alle angeschlossenen Peripheriegeräte aus.
Abbildung 27. Entfernen der Systemabdeckung Nächste Schritte 1. Bringen Sie die Systemabdeckung wieder an. Installieren der Systemabdeckung Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Vergewissern Sie sich, dass alle internen Kabel angeschlossen und verlegt sind. Achten Sie darauf, dass keine Werkzeuge oder zusätzliche Bauteile im System zurückbleiben. Schritte 1. Bringen Sie die Systemabdeckung am System an. 2.
Abbildung 28. Installieren der Systemabdeckung Nächste Schritte 1. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Stützleiste Die Stützleiste sorgt für eine Abstützung der Gehäusewände. Entfernen der Stützleiste Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Schritte 1. Lösen Sie die Fingerschrauben von der Stützleiste. 2.
Abbildung 29. Entfernen der Stützleiste Nächste Schritte 1. Bringen Sie die Stützleiste wieder an. Installieren der Stützleiste Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Schritte 1. Richten Sie die Aussparungen der Stützleiste an den Laschen am Systemgehäuse aus. 2. Ziehen Sie an den blauen Freigabestiften und senken Sie die Stützleiste in das System ab, bis sie einrastet. 3.
Abbildung 30. Anbringen der Stützleiste Nächste Schritte Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Lüfter Die Lüfter sind in das System integriert, um die durch den Betrieb des Systems erzeugte Wärme abzuführen. Diese Lüfter sorgen für die Kühlung der Prozessoren, Erweiterungskarten und Speichermodule.
2. Heben Sie den Lüfter aus der Lüfterbaugruppe. Abbildung 31. Entfernen des Kühlungslüfters Nächste Schritte 1. Setzen Sie den Lüfter wieder ein. Einsetzen eines Kühlungslüfters Voraussetzungen VORSICHT: Durch das Öffnen oder Entfernen der System bei eingeschaltetem System setzen Sie sich möglicherweise dem Risiko eines Stromschlags aus. Gehen Sie beim Entfernen oder Installieren von Lüftern äußerst vorsichtig vor. VORSICHT: Die Lüfter sind hot-swap-fähig.
Abbildung 32. Installieren des Lüfters Nächste Schritte 1. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Lüfterbaugruppe Die Lüfterbaugruppe enthält eine Reihe von Lüftern. Eine Störung im Kühlsystem des Servers kann zu einer Überhitzung des Servers und zu Schäden führen. Entfernen der Lüfterbaugruppe Voraussetzungen 1. Befolgen Sie die Hinweise, die im Abschnitt Sicherheitshinweise aufgeführt sind. 2.
Abbildung 33. Entfernen der Lüfterbaugruppe Nächste Schritte 1. Setzen Sie die Lüfterbaugruppe wieder ein. Installieren der Lüfterbaugruppe Voraussetzungen 1. Befolgen Sie die Hinweise, die im Abschnitt Sicherheitshinweise aufgeführt sind. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. VORSICHT: Merken Sie sich, wie das Kabel verlegt ist, wenn Sie es aus dem System entfernen.
Abbildung 34. Installieren der Lüfterbaugruppe Nächste Schritte 1. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Optionales USB 3.0-Modul Auf der Vorderseite des System kann ein zusätzlicher USB 3.0-Anschluss hinzugefügt werden. Das Kabel des USB 3.0-Moduls wird mit dem internen USB-Anschluss auf der Systemplatine verbunden. Der interne USB-Standardanschluss befindet sich unter dem Erweiterungskarten-Riser 2.
3. ANMERKUNG: Merken Sie sich, wie das Kabel verlegt ist, wenn Sie es aus dem System entfernen. Sie müssen das Kabel später wieder korrekt verlegen, damit es nicht abgeklemmt oder gequetscht wird. Ziehen Sie das USB 3.0-Modul aus dem System. Abbildung 35. Entfernen des USB 3.0-Moduls Nächste Schritte 1. Setzen Sie das USB 3.0-Modul oder den USB 3.0 Platzhalter wieder ein. ANMERKUNG: Das Entfernen eines USB 3.0-Platzhalters erfolgt auf ähnliche Weise wie das Entfernen des USB 3.0-Moduls.
Abbildung 36. Installieren des USB 3.0-Moduls ANMERKUNG: Informationen zur Position des Anschlusses finden Sie unter Anschlüsse auf der Systemplatine. Nächste Schritte 1. 2. 3. 4. 5. Setzen Sie die Lüfterbaugruppe wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Bringen Sie die Frontblende wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems.
ANMERKUNG: Notieren Sie das Routing von Strom- und Datenkabel, wenn Sie diese von der Systemplatine und vom optischen Laufwerk trennen. Schritte 1. Drücken Sie die Freigabelasche nach unten, um das optische Laufwerk zu entriegeln. 2. Schieben Sie das optische Laufwerk aus dem System. Abbildung 37.
Abbildung 38. Einsetzen des Platzhalters für das optische Laufwerk Nächste Schritte 1. Bauen Sie das optische Laufwerk wieder ein. Installieren des optischen Laufwerks Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Frontblende. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse. Entfernen Sie die Kühlungslüfterbaugruppe. Schritte 1.
Abbildung 39. Entfernen des Platzhalters für das optische Laufwerk 2. Richten Sie das optische Laufwerk mit dem Steckplatz für das optische Laufwerk auf der Systemvorderseite aus. 3. Schieben Sie das optische Laufwerk so weit rein, bis die Freigabelasche einrastet. Abbildung 40.
Nächste Schritte 1. Verbinden Sie die Strom- und Datenkabel mit dem Anschluss am optischen Laufwerk und dem Anschluss auf der Systemplatine. ANMERKUNG: Verlegen Sie das Kabel sorgfältig seitlich am System, damit es nicht eingeklemmt oder gequetscht wird. 2. 3. 4. 5. 6. Setzen Sie die Lüfterbaugruppe wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Bringen Sie die Frontblende wieder an.
Abbildung 41. Entfernen des linken Bedienfelds Nächste Schritte 1. Bauen Sie das linke Bedienfeld wieder ein. Installieren des linken Bedienfelds Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Frontblende. Entfernen Sie die Stützleiste. Entfernen Sie die Kühlgehäuse. Entfernen Sie die Kühlungslüfterbaugruppe. Schritte 1.
Abbildung 42. Installieren des linken Bedienfelds Nächste Schritte 1. 2. 3. 4. 5. Setzen Sie die Lüfterbaugruppe wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Bringen Sie die Frontblende wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Entfernen des rechten Bedienfelds Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise.
Abbildung 43. Entfernen des Bedienfelds Nächste Schritte 1. Bauen Sie das rechte Bedienfeld wieder ein. Installieren des rechten Bedienfelds Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Frontblende. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse. Entfernen Sie die Kühlungslüfterbaugruppe. Schritte 1.
Abbildung 44. Installieren des rechten Bedienfelds Nächste Schritte 1. 2. 3. 4. 5. 50 Setzen Sie die Lüfterbaugruppe wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Bringen Sie die Frontblende wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems.
Kühlgehäuse Das Kühlgehäuse leitet den Luftstrom durch das gesamte System. Die Kühlgehäuse sorgen für einen gleichmäßigen Luftstrom im Inneren des Systems. Das PowerEdge R940xa-System verfügt über vier Kühlgehäuse, die im Folgenden aufgeführt sind: ANMERKUNG: Stellen Sie sicher, dass Sie die Kühlgehäuse in der nachfolgend angegebenen Reihenfolge installieren oder entfernen: 1. 2. 3. 4.
Kühlgehäuse A Entfernen des Kühlgehäuses A Voraussetzungen VORSICHT: Betreiben Sie das System niemals ohne Kühlgehäuse. Das System kann andernfalls schnell überhitzen, was zum Abschalten des Systems und zu Datenverlust führt. 1. Befolgen Sie die Hinweise, die im Abschnitt Sicherheitshinweise aufgeführt sind. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. 3. Entfernen Sie den Haltebügel. Schritte 1. Drücken Sie auf die blauen Freigaberiegel. 2.
3. Entfernen Sie den Haltebügel. 4. Führen Sie die Kabel nach Bedarf im Inneren des Systems entlang der Wand und befestigen Sie die Kabel mit dem Kabelriegel. Schritte 1. Richten Sie die Schlitze auf dem Gehäuse A an den Führungen an der Verkleidung B aus. 2. Senken Sie das Kühlgehäuse in das System ab, bis die blauen Freigabelaschen einrasten. Abbildung 46. Installieren des Kühlgehäuses A Nächste Schritte 1. Bringen Sie den Haltebügel wieder an. 2.
GPU-Kühlgehäuse Entfernen des GPU-Kühlgehäuses Voraussetzungen ANMERKUNG: Das GPU-Kühlgehäuse muss nur entfernt werden, wenn eine GPU im System installiert ist. 1. 2. 3. 4. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse A. Schritte 1. Halten Sie das GPU-Kühlgehäuse auf beiden Seiten der Griffstellen an den Rändern fest. 2.
2. 3. 4. 5. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse A. Führen Sie die Kabel im Inneren des Systems entlang der Gehäusewand und befestigen Sie die Kabel mit der Kabelklemme. Schritte 1. Richten Sie die Aussparungen am GPU-Kühlgehäuse an den Laschen an Kühlgehäuse B aus. 2. Senken Sie das GPU-Kühlgehäuse in das System ab, bis es fest eingesetzt ist. Abbildung 48.
Kühlgehäuse B Entfernen von Kühlgehäuse B Voraussetzungen 1. 2. 3. 4. 5. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse A. Entfernen Sie die NVDIMM-N-Batterie, falls sie installiert ist. Schritte 1. Halten Sie das Kühlgehäuse an den blauen Griffstellen. 2. Heben Sie es aus dem System. Abbildung 49.
2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. 3. Führen Sie die Kabel gegebenenfalls im Inneren des Systems entlang der Gehäusewand, und befestigen Sie die Kabel mit der Kabelklemme. 4. Entfernen Sie die Stützleiste. 5. Entfernen Sie das Kühlgehäuse A. Schritte 1. Richten Sie die Aussparungen am Kühlgehäuse an den Laschen am Systemgehäuse und an Kühlgehäuse C aus. 2. Senken Sie das Kühlgehäuse ins System ab, bis es fest eingesteckt ist. Abbildung 50.
Kühlgehäuse C Entfernen von Kühlgehäuse C Voraussetzungen VORSICHT: Stellen Sie sicher, dass die Kabel von Riser 1 beim Platzieren von Kühlgehäuse C nicht eingeklemmt oder gequetscht werden. 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse A. Entfernen Sie die NVDIMM-N-Batterie, falls sie installiert ist.
Installieren von Kühlgehäuse C Voraussetzungen 1. 2. 3. 4. 5. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie das Kühlgehäuse A. Entfernen Sie das Kühlgehäuse B. Schritte 1. Richten Sie die Metalllasche am Kühlgehäuse an den Aussparungen in der Gehäusewand aus. 2.
Entfernen der NVDIMM-N-Batterie Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. VORSICHT: NVDIMM-N Akku ist nicht hot-swap-fähig. Um Datenverlust zu vermeiden und auf mögliche Schäden an Ihrem System beginnen, vergewissern Sie sich, dass Ihr System-LEDs auf der LEDs NVDIMM-N und LEDs auf NVDIMM-N Akku ausgeschaltet sind vor dem Entfernen des NVDIMM-N Akku.
VORSICHT: NVDIMM-N Akku ist nicht hot-swap-fähig. Um Datenverlust zu vermeiden und auf mögliche Schäden an Ihrem System beginnen, vergewissern Sie sich, dass Ihr System-LEDs auf der LEDs NVDIMM-N und LEDs auf NVDIMM-N Akku ausgeschaltet sind, bevor Sie mit der Installation der NVDIMM-N Akku. VORSICHT: Um Beschädigungen am Batteriesockel zu vermeiden, müssen Sie den Sockel fest abstützen, wenn Sie eine Batterie installieren oder entfernen. 2.
Tabelle 4. Unterstützte Rückwandplatinen für das PowerEdge R940xa-System System- Unterstützte Rückwandplatinenoptionen 2,5-Zoll(x24)SAS/SATA-Rückwandplatine PowerEdge R940xa 2,5-Zoll(x24)-Rückwanderweiterungskarte, die 4 SAS/SATA/NVMe Festplattenlaufwerke unterstützt 2,5-Zoll(x8)SAS/SATA-Rückwandplatine Untere 2,5-Zoll(x8)SAS/SATA-Rückwandplatine Abbildung 55. 2,5-Zoll(x24)SAS/SATA-Rückwandplatine 1. Slimline-SAS-Kabelanschluss 3. Netzkabelanschluss 5. Netzkabelanschluss Abbildung 56.
Abbildung 57. 2,5-Zoll(x8)SAS/SATA-Rückwandplatine 1. Mini-SAS-Festplatte B 1 3. Netzkabelanschluss 2. Signalanschluss der Rückwandplatine 4. Mini-SAS-Festplatte A 1 Abbildung 58. Untere 2,5-Zoll(x8)SAS/SATA-Rückwandplatine 1. Mini-SAS-Festplatte B 1 3. Netzkabelanschluss 2. Mini-SAS-Festplatte A 1 4.
Schritte 1. Lösen Sie die beiden Flügelschrauben auf der Rückwanderweiterungsplatine. 2. Halten Sie die blauen Freigabelaschen gedrückt und heben Sie die Rückwanderweiterungsplatine an, um die Schlitze aus den Führungen am System zu lösen. 3. Heben Sie die Rückwanderweiterungsplatine aus dem System. Abbildung 59. Entfernen der Rückwanderweiterungsplatine 4. Halten Sie die blauen Freigabelaschen gedrückt und heben Sie die unteren Rückwandplatine an, um die Schlitze aus den Führungen am System zu lösen. 5.
Abbildung 60. Entfernen der unteren Rückwandplatine Nächste Schritte 1. Setzen Sie die Rückwandplatine wieder ein. Installieren der Rückwandplatine Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. 3. Ziehen Sie die Kabel ab. a. Ziehen Sie ggf. dass Slimline-Kabel, das I2C-Kabel und das Netzkabel von der Rückwandplatine ab. b.
Abbildung 61. Installieren der unteren Rückwandplatine 3. Richten Sie die Aussparungen an der Rückwandplatine an den Führungen am System aus und halten Sie dabei die blauen Freigabelaschen fest. 4. Ziehen Sie die beiden Flügelschrauben fest, mit denen die Rückwanderweiterungsplatine befestigt ist. Abbildung 62.
Nächste Schritte 1. Schließen Sie die Kabel an. a. Schließen Sie ggf. dass Slimline-Kabel, das I2C-Kabel und das Netzkabel von der Rückwandplatine an. b. Schließen Sie das I2C-Kabel und das Netzkabel von der Systemplatine an. 2. Setzen Sie die Lüfterbaugruppe wieder ein. 3. Bauen Sie die Kühlgehäuse wieder ein. 4. Bringen Sie die Stützleiste wieder an. 5. Setzen Sie die Laufwerke wieder ein. 6. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems.
Abbildung 65. 8 x Chipsatz SATA Abbildung 66.
Abbildung 67. 32 x 2 P-Single-PERC/GPU/Kein NVMe Abbildung 68.
Abbildung 69. 32 x 4 P-Single-PERC/GPU/NVMe Abbildung 70. 32 x 2 P-Single-PERC/Keine GPU/NVMe Systemspeicher Das System enthält 48 Speichersockel, die in vier Sätze zu 12 Sockeln aufgeteilt sind, also ein Satz für jeden Prozessor. Jeder Satz von zwölf Speichersockeln ist in vier Kanäle organisiert. Jedem Prozessor sind sechs Speicherkanäle zugewiesen. In den einzelnen Kanälen sind die Auswurfhebel am jeweils ersten Sockel weiß und am jeweils zweiten Sockel schwarz.
Abbildung 71. Positionen der Speichersockel Die Speicherkanäle sind folgendermaßen organisiert: Tabelle 5.
Tabelle 5. Speicherkanäle (fortgesetzt) Prozessor Kanal 0 Kanal 1 Kanal 2 Kanal 3 Kanal 4 Kanal 5 Prozessor 4 Steckplätze D1 und D7 Steckplätze D2 und D8 Steckplätze D3 und D9 Steckplätze D4 und D10 Steckplätze D5 und D11 Steckplätze D6 und D12 Allgemeine Richtlinien zur Installation von Speichermodulen Um eine optimale Leistung des Systems zu gewährleisten, sollten Sie bei der Konfiguration des Systemspeichers die nachfolgend beschriebenen allgemeinen Richtlinien beachten.
● Unausgeglichene Arbeitsspeicherkonfigurationen führen zu Leistungseinbußen. Für optimale Leistung sollten Sie die Speicherkanäle also immer identisch bestücken, mit identischen DIMMs. ● Setzen Sie für maximale Leistung pro Prozessor jeweils sechs identische Speichermodule gleichzeitig ein (ein DIMM pro Kanal). Aktualisierung der DIMM-Bestückung im Modus „Performance Optimized“ (Leistungsoptimiert) bei vier bzw.
Tabelle 6. Unterstützte NVDIMM-Ns für Konfigurationen mit zwei Prozessoren (fortgesetzt) Konfiguration Beschreibung Regeln für die Arbeitsspeicherbestückung RDIMMs NVDIMM-N 22x 32 GB RDIMMs, 4x NVDIMM-Ns Dasselbe gilt für alle 12x RDIMM-Konfigurationen. Siehe Konfiguration 1.
Tabelle 7.
Tabelle 7.
Tabelle 8. 2-Sockel-PMem-Konfigurationen (fortgesetzt) Anzahl PMem DRAM DRAM der -Bestü -Bestü -Kapa CPUs ckung ckung zität im (GB) Server PMem -Kapa zität (GB) Betriebssy stemspeic her im Speicherm odus (GB) Gesam tspeic her (GB) Gesam tspeic her pro CPU (GB) Verhältnis DRAM zu OptaneSpeicher Erfordert eine Moder LCPU Unterstütz t im AppDirectModus Unterstütz t im Speicherm odus 2 128 GB x 4 16 GB x 8 128 512 512 640 320 1:4 Nein Ja Ja 2 128 GB x 4 16 192 GB x 12 512 k. A.
Tabelle 8. 2-Sockel-PMem-Konfigurationen (fortgesetzt) Anzahl PMem DRAM DRAM der -Bestü -Bestü -Kapa CPUs ckung ckung zität im (GB) Server PMem -Kapa zität (GB) Betriebssy stemspeic her im Speicherm odus (GB) Gesam tspeic her (GB) Gesam tspeic her pro CPU (GB) Verhältnis DRAM zu OptaneSpeicher Erfordert eine Moder LCPU Unterstütz t im AppDirectModus Unterstütz t im Speicherm odus 2 256 GB x 8 64 768 GB x 12 2.048 k. A. 2.816 1.408 1:2,7 L SKU Ja Nein 2 256 64 768 GB x 12 GB x 12 3.
Tabelle 9. 4-Sockel-PMem-Konfigurationen (fortgesetzt) Anzahl PMemder Bestück CPUs im ung Server DRAM- DRAM- PMem- Betriebs Gesamt Gesamt Bestück Kapazitä Kapazitä systems speicher speicher ung t (GB) t (GB) peicher (GB) pro CPU im (GB) Speiche rmodus (GB) Verhältn Erforder is DRAM t eine zu M- oder Optane- L-CPU Speiche r Unterst ützt im AppDirectModus Unterst ützt im Speiche rmodus 4 256 GB x 16 64 GB x 24 1.536 4.096 k. A. 5.632 1.408 1:2,7 L SKU Ja Nein 4 256 GB x 24 64 GB x 24 1.
Tabelle 11. Betriebsmodi des Arbeitsspeichers (fortgesetzt) Memory Operating Mode Beschreibung Mirror Mode Ist der Mirror Mode (Spiegelungsmodus) aktiviert, hält das System zwei identische Kopien der Daten im Arbeitsspeicher vor und der insgesamt verfügbare Systemspeicher beträgt 50 % des insgesamt installierten physischen Speichers. Die restlichen 50 % werden zur Spiegelung der aktiven Speichermodule verwendet.
Tabelle 12. Regeln für die Arbeitsspeicherbestückung Prozessor Konfiguration Speicherbestückung Informationen zur Arbeitsspeicherbestückung 2 Prozessoren (Mit Prozessor 1 beginnen. Prozessor 1 und Prozessor 2 sollten identisch sein.) Bestückungsreihenfolge im Optimierungsmodus (unabhängige Kanäle) A{1}, B{1}, A{2}, B{2}, A{3}, B{3}, A{4}, B{4}, A{5}, B{5}, A{6}, B{6} Eine ungerade Anzahl von DIMM-Bestückung pro Prozessor ist zulässig.
Tabelle 12. Regeln für die Arbeitsspeicherbestückung (fortgesetzt) Prozessor Konfiguration Speicherbestückung Informationen zur Arbeitsspeicherbestückung ANMERKUNG: Um eine optimale Leistung zu gewährleisten, werden 6 DIMMs oder 12 DIMMs pro Prozessor empfohlen. Die Bestückungsreihenfolge im Optimierungsmodus weicht bei Konfigurationen mit 16 oder 32 DIMMs und 2 Prozessoren von der herkömmlichen Reihenfolge ab.
3. Entfernen Sie die Stützleiste. 4. Entfernen Sie die Kühlgehäuse. WARNUNG: Lassen Sie die Speichermodule ausreichend lange abkühlen nach dem Ausschalten des Systems. Fassen Sie Speichermodule an den Rändern an und vermeiden Sie den Kontakt mit Komponenten auf den Speichermodulen. VORSICHT: Um eine ordnungsgemäße Kühlung zu gewährleisten, müssen in allen nicht belegten Speichersockeln Speichermodulplatzhalter installiert werden.
1. Befolgen Sie die Sicherheitshinweise unter Sicherheitshinweise. 2. Befolgen Sie die Anweisungen im Kapitel Before working inside your system (Vor der Arbeit an Komponenten im Inneren des Systems). VORSICHT: Um Datenverlust zu vermeiden und auf mögliche Schäden an Ihrem System beginnen, vergewissern Sie sich, dass Ihr System-LEDs auf der LEDs NVDIMM-N und LEDs auf NVDIMM-N Akku ausgeschaltet sind vor dem Entfernen des NVDIMM-N Akku. 3. Entfernen Sie die Abstützleiste. 4. Entfernen Sie die Kühlgehäuse.
6. Führen Sie die Systemspeicherüberprüfung in der Systemdiagnose durch. Prozessoren und Kühlkörper Der Prozessor verwaltet steuert Speicher, periphere Schnittstellen und andere Komponenten des Systems. Das System kann mehr als eine Prozessorkonfiguration haben. Der Kühlkörper nimmt die Wärme erzeugt durch den Prozessor und hilft dem Prozessor zur Aufrechterhaltung des optimalen Temperaturniveau.
Abbildung 74. Entfernen eines PKM von CPU 1 oder 2 Abbildung 75. Entfernen eines PKM von CPU 3 oder 4 Nächste Schritte 1. Setzen Sie das Prozessor- und Kühlkörpermodul wieder ein.
Entfernen des Prozessors aus dem Prozessor- und Kühlkörpermodul Voraussetzungen WARNUNG: Kühlkörper sind auch nach dem Ausschalten des Systems eine Zeitlang zu heiß zum Anfassen. Lassen Sie den Kühlkörper einen Moment abkühlen, bevor Sie ihn entfernen. ANMERKUNG: Entfernen Sie den Prozessor nur dann vom Prozessor- und Kühlkörpermodul, wenn Sie den Prozessor oder den Kühlkörper austauschen. Beim Austausch einer Systemplatine ist dieses Verfahren nicht erforderlich. 1.
Abbildung 77. Lösen der Prozessorhalterung von CPU 3/4 3. Heben Sie die Halterung und den Prozessor vom Kühlkörper, und legen Sie den Prozessor mit der Anschlussseite nach unten auf die Prozessorablage. 4. Biegen Sie die äußeren Kanten der Halterung, um den Prozessor aus der Halterung zu lösen. ANMERKUNG: Stellen Sie sicher, dass der Prozessor und der Halterung sind in das Fach eingelegt nach dem Entfernen des Kühlkörpers. Abbildung 78. Entfernen der Prozessorhalterung Nächste Schritte 1.
Installieren des Prozessors im Prozessor- und Kühlkörpermodul Voraussetzungen WARNUNG: Kühlkörper sind auch nach dem Ausschalten des Systems eine Zeitlang zu heiß zum Anfassen. Lassen Sie den Kühlkörper einen Moment abkühlen, bevor Sie ihn entfernen. ANMERKUNG: Entfernen Sie den Prozessor nur dann vom Prozessor- und Kühlkörpermodul, wenn Sie den Prozessor oder den Kühlkörper austauschen. Beim Austausch einer Systemplatine ist dieses Verfahren nicht erforderlich. 1.
Abbildung 80. Auftragen von Wärmeleitpaste auf der Oberseite des Prozessors 5. Setzen Sie den Kühlkörper auf den Prozessor und drücken Sie den unteren Teil des Kühlkörpers nach unten, bis die Halterung auf dem Kühlkörper einrastet. ANMERKUNG: ● Stellen Sie sicher, dass die beiden Löcher für Führungsstifte an Halterung mit Führungslöchern auf dem Kühlkörper übereinstimmen. ● Drücken Sie nicht auf die Lamellen des Kühlkörpers.
VORSICHT: Um eine Beschädigung der Lamellen des Kühlkörpers zu vermeiden, drücken Sie nicht auf die Kühlkörperlamellen. ANMERKUNG: Stellen Sie sicher, dass Sie das PKM parallel zur Systemplatine halten, um Beschädigungen an den Komponenten zu vermeiden. 2. Drücken Sie die blauen Halteklammern nach innen, damit der Kühlkörper nach unten einrasten kann. 3. Ziehen Sie mit dem Torx-Schraubenzieher der Größe T30 die Schrauben am Kühlkörper in der nachfolgend angegebenen Reihenfolge fest: a.
Abbildung 82. Installieren des PKM auf CPU 3 oder 4 Nächste Schritte 1. 2. 3. 4. Setzen Sie die Lüfterbaugruppe wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems.
Abbildung 83. Nummerierung der PCIe-Steckplätze Die folgende Tabelle enthält ausführliche Angaben zu den technischen Daten der Erweiterungskarten-Riser: Tabelle 13.
Tabelle 14. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) in einer Konfiguration mit zwei Prozessoren Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Intel 25 Gbit-NICs 11,4 2 Intel 25 Gbit-NICs 6.7 2 Nvidia-GPU 4.11 2 Intel FPGA 11,4 2 Xilinx-FPGA ANMERKUNG: Verwenden Sie für die Installation oder das Entfernen der Xilinx-Karte einen Beschleuniger mit doppelter Breite. 11,4 2 Dell Design PERC10 7 1 Mellanox Infiniband HCA EDR 6.
Tabelle 14. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) in einer Konfiguration mit zwei Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Emulex FC16-HBA 6.7 2 Qlogic FC16-HBA 11,4 2 Qlogic FC16-HBA 6.7 2 Broadcom 10 Gigabit-NICs 6.7 2 Broadcom 10 Gigabit-NICs 11,4 2 INTEL 10 Gigabit-NICs 6.7 2 INTEL 10 Gigabit-NICs 11,4 2 Mellanox 10 Gigabit-NICs 6.
Tabelle 15. Riser-Konfiguration (PCIe-x8-Riser 1 + PCIe-x8-Riser 2) in einer Konfiguration mit zwei Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten INTEL Omni-Path HFI 6.7 2 BOSS (Dell Design) 3,4,10,11 1 BOSS (Dell Design) 6.7 1 Externes RAID (Dell Design) 6.7 2 Externes RAID (Dell Design) 3,4,10,11 2 Mellanox Infiniband HCA FDR 6.7 2 INTEL 40 Gigabit-NICs 3,4,10,11 4 INTEL 40 Gigabit-NICs 6.7 2 Mellanox 40 Gigabit-NICs 6.
Tabelle 15. Riser-Konfiguration (PCIe-x8-Riser 1 + PCIe-x8-Riser 2) in einer Konfiguration mit zwei Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Emulex FC8-HBA 3,4,10,11 4 Qlogic FC8-HBA 6.7 2 Qlogic FC8-HBA 3,4,10,11 4 Broadcom 1 Gigabit-NICs 3,4,10,11 4 Broadcom 1 Gigabit-NICs 6.7 2 INTEL 1 Gigabit-NICs 6.7 2 INTEL 1 Gigabit-NICs 3,4,10,11 4 Nicht-RAID (Dell Design) 6.
Tabelle 16. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten INTEL 40 Gigabit-NICs 5,12,9,11,2,4 6 INTEL 40 Gigabit-NICs 6.7 2 Mellanox 40 Gigabit-NICs 6.7 2 Mellanox 40 Gigabit-NICs 5,12,9,11,2,4 6 Emulex FC32-HBA 5,12,9,11,2,4 6 Emulex FC32-HBA 6.7 2 Qlogic FC32-HBA 5,12,9,11,2,4 6 Qlogic FC32-HBA 6.7 2 Broadcom 25 Gigabit-NICs 6.
Tabelle 16. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten INTEL 1 Gigabit-NICs 5,12,9,11,2,4 6 Nicht-RAID (Dell Design) 6.
Tabelle 17. Riser-Konfiguration (PCIe-x8-Riser 1 + PCIe-x8-Riser 2) in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Qlogic 25 Gigabit-NICs 1,2,3,4,5,8,9,10,11,12 10 Qlogic 25 Gigabit-NICs 6.7 2 Emulex FC16-HBA 1,2,3,4,5,8,9,10,11,12 10 Emulex FC16-HBA 6.7 2 Qlogic FC16-HBA 1,2,3,4,5,8,9,10,11,12 10 Qlogic FC16-HBA 6.7 2 Broadcom 10 Gigabit-NICs 6.
Tabelle 18. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) mit NVMe in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Intel FPGA 9,11,2,4 4 Xilinx-FPGA ANMERKUNG: Verwenden Sie für die Installation oder das Entfernen der Xilinx-Karte einen Beschleuniger mit doppelter Breite. 9,11,2,4 4 Dell Design PERC10 7 1 Mellanox Infiniband HCA EDR 6.
Tabelle 18. Riser-Konfiguration (PCIe-x16-Riser 1 + PCIe-x16-Riser 2) mit NVMe in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Emulex FC16-HBA 6.7 2 Qlogic FC16-HBA 9,11,2,4 4 Qlogic FC16-HBA 6.7 2 Broadcom 10 Gigabit-NICs 6.7 2 Broadcom 10 Gigabit-NICs 9,11,2,4 4 INTEL 10 Gigabit-NICs 6.7 2 INTEL 10 Gigabit-NICs 9,11,2,4 4 Mellanox 10 Gigabit-NICs 6.
Tabelle 19. Riser-Konfiguration (PCIe-x8-Riser 1 + PCIe-x8-Riser 2) mit NVMe in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten INTEL Omni-Path HFI 6.7 2 BOSS (Dell Design) 1,2,3,4,8,9,10,11 1 BOSS (Dell Design) 6.7 1 Externes RAID (Dell Design) 6.7 2 Externes RAID (Dell Design) 1,2,3,4,8,9,10,11 2 Mellanox Infiniband HCA FDR 6.7 2 INTEL 40 Gigabit-NICs 1,2,3,4,8,9,10,11 8 INTEL 40 Gigabit-NICs 6.
Tabelle 19. Riser-Konfiguration (PCIe-x8-Riser 1 + PCIe-x8-Riser 2) mit NVMe in einer Konfiguration mit vier Prozessoren (fortgesetzt) Kartentyp Steckplatzpriorität Maximale Anzahl von Karten Emulex FC8-HBA 1,2,3,4,8,9,10,11 8 Qlogic FC8-HBA 6.7 2 Qlogic FC8-HBA 1,2,3,4,8,9,10,11 8 Broadcom 1 Gigabit-NICs 1,2,3,4,8,9,10,11 8 Broadcom 1 Gigabit-NICs 6.7 2 INTEL 1 Gigabit-NICs 6.7 2 INTEL 1 Gigabit-NICs 1,2,3,4,8,9,10,11 8 Nicht-RAID (Dell Design) 6.
Abbildung 84.
Abbildung 85. Entfernen von PCIe-x8-Riser 2 ANMERKUNG: Der Einbau eines Abdeckblechs über einem leeren Erweiterungskartensteckplatz ist erforderlich, damit die FCC-Bestimmungen bezüglich der Funkentstörung eingehalten werden. Die Abdeckungen halten auch Staub und Schmutz vom System fern und helfen, die korrekte Kühlung und den Luftstrom innerhalb des Systems aufrechtzuerhalten. Nächste Schritte 1. Setzen Sie den Erweiterungskarten-Riser wieder ein.
Abbildung 86.
Abbildung 87. Installieren von PCIe-x8-Riser 2 Nächste Schritte 1. Bauen Sie die Kühlgehäuse wieder ein. 2. Bringen Sie die Stützleiste wieder an. 3. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Entfernen der Erweiterungskarte aus dem Riser Voraussetzungen 1. 2. 3. 4. 5. Befolgen Sie die Hinweise, die im Abschnitt Sicherheitshinweise aufgeführt sind. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie den Haltebügel.
Abbildung 88. Entfernen der Erweiterungskarte aus dem Riser Nächste Schritte 1. Wenn Sie die Erweiterungskarte nicht wieder einbauen, installieren Sie ein Abdeckblech. ANMERKUNG: Der Einbau eines Abdeckblechs über einem leeren Erweiterungskartensteckplatz ist erforderlich, damit die FCC-Bestimmungen bezüglich der Funkentstörung eingehalten werden. Die Abdeckungen halten auch Staub und Schmutz vom System fern und helfen, die korrekte Kühlung und den Luftstrom innerhalb des Systems aufrechtzuerhalten. 2.
Abbildung 89. Installieren des Erweiterungskarten-Risers Nächste Schritte 1. 2. 3. 4. Installieren Sie den Erweiterungskarten-Riser. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie den Haltebügel wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. Entfernen der Erweiterungskarte von der Systemplatine Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise.
Abbildung 90. Entfernen der Erweiterungskarte Abbildung 91. Installieren des Abdeckblechs eines Risers Nächste Schritte 1. Wenn Sie die Erweiterungskarte nicht wieder einsetzen, installieren Sie ein Abdeckblech.
ANMERKUNG: Bewahren Sie den Abdeckbleche für den zukünftigen Gebrauch auf. Für leere Erweiterungskartensteckplätzen sind Abdeckbleche erforderlich, um die FCC-Bestimmungen (Federal Communications Commission) einzuhalten. Die Abdeckungen halten auch Staub und Schmutz vom System fern und helfen, die korrekte Kühlung und den Luftstrom innerhalb des Systems aufrechtzuerhalten. 2. Setzen Sie den Erweiterungskarten-Riser wieder ein. Installieren der Erweiterungskarte auf der Systemplatine Voraussetzungen 1. 2.
Abbildung 92. Entfernen eines Abdeckblechs von einem Riser 3. Fassen Sie die Karte an den Rändern an und richten Sie sie am Erweiterungskartenanschluss auf der Systemplatine aus. Abbildung 93. Installieren der Erweiterungskarte 4. Drücken Sie fest auf die Erweiterungskarte, bis die Karte vollständig eingesetzt ist. 5. Drücken Sie auf die blaue Erweiterungskartenverriegelung, bis die Verriegelung einrastet.
6. Ziehen Sie die Kabel von der Stromzwischenplatine (PIB), der Systemplatine und der Rückwandplatine ab. ANMERKUNG: Stellen Sie sicher, dass Sie auch die Kabel entfernen, die mit der Kabelhalterung befestigt und entlang der Gehäusewand verlegt sind. ANMERKUNG: Entfernen Sie das Laufwerkskabel und die Systemplatinenkabel. Nächste Schritte 1. 2. 3. 4. Setzen Sie den Erweiterungskarten-Riser wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an.
5. Öffnen Sie den Erweiterungskartenriegel. 6. Fassen Sie die Karte an den Rändern an, drücken Sie auf den Entriegelungsriegel des PCIe-Anschlusses und heben Sie die Karte aus dem Anschluss des Risers. VORSICHT: Stellen Sie sicher, dass Sie das GPU-Stromkabel trennen, bevor Sie die GPU aus dem System entfernen. 7. Entfernen Sie das Slimline-Kabel der Systemplatine aus dem Kabelhalter am Riser. 8. Trennen Sie das GPU-Stromkabel von der GPU. 9. Entfernen Sie die GPU aus dem Riser. Abbildung 94.
Abbildung 95. Installieren der GPU-Platzhalterkarte 14. Schließen Sie die Abdeckung. 15. Schließen Sie die Kartenverriegelung, indem Sie sie nach unten drücken, bis sie einrastet. Nächste Schritte Bauen Sie das GPU-Gehäuse wieder ein. Einbauen der GPU Voraussetzungen ANMERKUNG: Die GPU-Karte kann nur in eine X16 PCIe-Riser-Konfiguration eingebaut werden. ANMERKUNG: Die GPU-Verkleidung darf nur entfernt werden, wenn eine GPU im System installiert wird. 1.
Schritte 1. Nehmen Sie die Erweiterungskarte aus der Verpackung und bereiten Sie sie für den Einbau vor. ANMERKUNG: Anweisungen dazu finden Sie in der Dokumentation, die mit der Karte geliefert wurde. 2. Drücken und schieben Sie die Entriegelungstaste nach oben, um die Abdeckung abzuheben. 3. Öffnen Sie den Kartenriegel. 4. Entfernen Sie das Abdeckblech vom Erweiterungskartenhalter. ANMERKUNG: Bewahren Sie den Abdeckbleche für den zukünftigen Gebrauch auf.
Abbildung 97. Einbauen der GPU Nächste Schritte 1. 2. 3. 4. 5. Installieren Sie den Erweiterungskarten-Riser. Schließen Sie das GPU-Netzkabel, das Slimline-Kabel der Systemplatine und das Netzkabel des Riser an. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie den Haltebügel wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems. M.2-SSD-Modul Die BOSS-Karte ist eine einfache Karte mit RAID-Lösung, die speziell für den Start des Betriebssystems konzipiert wurde.
Schritte 1. Lösen Sie die Schraube und heben Sie die Haltebänder an, mit denen das M.2-BOSS-Modul auf der BOSS-Karte befestigt ist. 2. Ziehen Sie das M.2-BOSS-Modul von der BOSS-Karte. Abbildung 98. Entfernen des M.2-BOSS-Moduls Nächste Schritte Setzen Sie das M.2-BOSS-Modul wieder ein. Installieren des M.2-BOSS-Moduls Voraussetzungen 1. 2. 3. 4. 5. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Entfernen Sie die Stützleiste. Entfernen Sie die Kühlgehäuse.
Abbildung 99. Installieren des M.2-BOSS-Moduls Nächste Schritte 1. Setzen Sie die BOSS-Karte wieder ein. ANMERKUNG: Das Einsetzen der BOSS-Karte erfolgt auf ähnliche Weise wie das Installieren einer Erweiterungskarte. 2. 3. 4. 5. Setzen Sie den Erweiterungskarten-Riser wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an. Befolgen Sie die Schritte unter Nach der Arbeit an Komponenten im Inneren des Systems.
Abbildung 100. Entfernen der Mikro-SD-Karte Nächste Schritte 1. Setzen Sie die Mikro-SD-Karte wieder ein. Einsetzen der MicroSD-Karte Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie die Kühlgehäuse. Entfernen Sie den Erweiterungskarten-Riser. Entfernen Sie das IDSDM- oder vFlash-Modul.
Entfernen des IDSDM- oder vFlash-Moduls Voraussetzungen 1. 2. 3. 4. 5. 6. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Entfernen Sie die Stützleiste. Entfernen Sie die Kühlgehäuse. Entfernen Sie den Erweiterungskarten-Riser. Entfernen Sie die MicroSD-Karten, wenn Sie das IDSDM- oder vFlash-Modul austauschen.
4. Entfernen Sie die Kühlgehäuse. 5. Entfernen Sie den Erweiterungskarten-Riser. 6. Entfernen Sie die MicroSD-Karten, wenn Sie das IDSDM- oder vFlash-Modul austauschen. ANMERKUNG: Vermerken Sie nach dem Entfernen auf jeder microSD-Karte die Nummer des zugehörigen Steckplatzes. Schritte 1. Machen Sie den IDSDM- oder vFlash-Anschluss auf Riser 1 ausfindig. 2. Richten Sie das IDSDM- oder vFlash-Modul am Anschluss auf der Systemplatine aus. 3.
3. Entfernen Sie die Stützleiste. 4. Entfernen Sie die Kühlgehäuse. 5. Entfernen Sie den Erweiterungskarten-Riser 1. Schritte 1. Lösen Sie mit einem Kreuzschlitzschraubendreher der Größe 2 die zwei unverlierbaren Schrauben, mit denen die Netzwerktochterkarte (NDC) auf der Systemplatine befestigt ist. 2. Halten Sie die Netzwerktochterkarte an den Rändern und heben Sie sie an, um sie aus dem Anschluss auf der Systemplatine zu entfernen. 3.
2. Drücken Sie auf die blauen Griffstellen, bis der Kartenstecker fest im Anschluss der Systemplatine eingesetzt ist. 3. Ziehen Sie mit einem Kreuzschlitzschraubendreher Nr. 2 die unverlierbaren Schrauben fest, mit denen die Netzwerkzusatzkarte an der Systemplatine befestigt wird. Abbildung 104. Einsetzen der Netzwerkzusatzkarte Nächste Schritte 1. 2. 3. 4. Setzen Sie den Erweiterungskarten-Riser wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an.
Schritte 1. Suchen Sie den Batteriesockel. Weitere Informationen finden Sie unter Anschlüsse auf der Systemplatine. VORSICHT: Um Beschädigungen am Batteriesockel zu vermeiden, müssen Sie den Sockel fest abstützen, wenn Sie eine Batterie installieren oder entfernen. 2. Hebeln Sie die Systembatterie mit einem Stift aus Kunststoff heraus. Abbildung 105. Entfernen der Systembatterie 3.
Austauschen des optionalen internen USB-Speichersticks Voraussetzungen VORSICHT: Damit der USB-Speicherstick andere Komponenten im Servermodul nicht behindert, darf er die folgenden maximalen Abmessungen nicht überschreiten: 15,9 mm Breite x 57,15 mm Länge x 7,9 mm Höhe. 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. 3. Entfernen Sie die Kühlgehäuse. Schritte 1.
ANMERKUNG: Überprüfen Sie unbedingt, ob in dem System mehrere Hot-Spare-Netzteile installiert sind. Entfernen eines Netzteilplatzhalters Voraussetzungen Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Schritte Wenn Sie ein zusätzliches Netzteil installieren, entfernen Sie den Netzteilplatzhalter im Schacht, indem sie den Platzhalter nach außen ziehen.
Entfernen eines Netzteils Die Verfahren für das Installieren von Wechselstrom- bzw. Gleichstrom-Netzteilen sind identisch. Voraussetzungen VORSICHT: Das System benötigt für den Normalbetrieb ein Netzteil (PSU). Entfernen und ersetzen Sie bei Systeme mit redundanter Stromversorgung nur ein Netzteil auf einmal, wenn das System eingeschaltet ist. 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2.
2. Lösen Sie die Verriegelung, damit es einrastet. Abbildung 110. Einbauen des Netzteils Nächste Schritte 1. Wenn Sie die Zugentlastungsleiste und deren Halterung entfernt haben, bringen Sie diese wieder an. Weitere Informationen zur Zugentlastungsleiste und deren Halterung finden Sie im Schieneninstallationshandbuch unter Dell.com/poweredgemanuals. 2. Verbinden Sie das Stromkabel mit dem Netzteil und mit einer Steckdose. VORSICHT: Sichern Sie das Netzkabel beim Anschließen mit dem Band.
Eingangsanforderungen ● Netzspannung: –(48–60) V Gleichstrom ● Stromverbrauch: 32 A (maximal) Inhalt des Kits ● Dell-Teilenummer 6RYJ9 Klemmenblock oder gleichwertiges Produkt (1) ● Mutter 6-32 mit Sicherungsscheibe (1) Erforderliche Werkzeuge Abisolierzangen, mit denen Isolierung der Größe 10 AWG von festem oder verdrilltem, isoliertem Kupferdraht entfernt werden kann ANMERKUNG: Verwenden Sie Alpha Wire-Draht mit der Teilenummer 3080 oder einen gleichwertigen Draht (Verlitzung 65/30).
Abbildung 111. Entfernen der Stromzwischenplatine Nächste Schritte 1. Setzen Sie die Stromzwischenplatine wieder ein. Installieren der Stromzwischenplatine Voraussetzungen 1. 2. 3. 4. 5. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. Entfernen Sie die Stützleiste. Entfernen Sie die Kühlgehäuse. Entfernen Sie die Netzteileinheiten. Entfernen Sie den Erweiterungskarten-Riser 2. ANMERKUNG: Merken Sie sich, wie das Kabel verlegt ist, wenn Sie es aus dem System entfernen.
Abbildung 112. Installieren der Stromzwischenplatine 3. Führen Sie die Kabel in den Halteklammern. 4. Schließen Sie die Kabel der Stromzwischenplatine an. 5. Schließen Sie die Stromkabel an die Systemplatine und die Festplattenrückwandplatine an. Nächste Schritte 1. 2. 3. 4. 5. Setzen Sie den Erweiterungskarten-Riser 2 wieder ein. Setzen Sie die Netzteile wieder ein. Bauen Sie die Kühlgehäuse wieder ein. Bringen Sie die Stützleiste wieder an.
Info über diese Aufgabe VORSICHT: Sobald das TPM-Plug-in-Modul eingesetzt ist, ist es kryptografisch an diese bestimmte Systemplatine gebunden. Wenn Sie versuchen, ein installiertes TPM-Steckmodul zu entfernen, wird die kryptografische Bindung gebrochen. Das entfernte TPM lässt sich dann nicht wieder auf der Systemplatine installieren und kann auch auf keiner anderen Systemplatine installiert werden. Entfernen des TPM Schritte 1. Machen Sie den TPM-Anschluss auf der Systemplatine ausfindig. 2.
Initialisieren des TPM für BitLocker-Benutzer Schritte 1. Initialisieren Sie das TPM. Weitere Informationen finden Sie unter Initialisieren des TPM für Intel TXT-Benutzer. 2. Die TPM Status (TPM-Status) ändert sich zu Enabled (Aktiviert). Initialisieren des TPM 1.2 für TXT-Benutzer Schritte 1. Drücken Sie beim Starten des System auf , um das System-Setup aufzurufen. 2.
Entfernen der Systemplatine Voraussetzungen VORSICHT: Wenn Sie das TPM (Trusted Program Module) mit Verschlüsselung verwenden, werden Sie möglicherweise aufgefordert, während des System- oder Programm-Setups einen Wiederherstellungsschlüssel zu erstellen. Diesen Wiederherstellungsschlüssel sollten Sie unbedingt erstellen und sicher speichern.
Abbildung 114. Entfernen der Systemplatine Nächste Schritte 1. Bauen Sie die Systemplatine ein. Einsetzen der Systemplatine Voraussetzungen 1. Befolgen Sie die Sicherheitsrichtlinien unter Sicherheitshinweise. 2. Befolgen Sie die Schritte unter Vor der Arbeit an Komponenten im Innern des Systems. Schritte 1. Nehmen Sie die Austausch-Systemplatinenbaugruppe aus der Verpackung. VORSICHT: Heben Sie die Systemplatinenbaugruppe nicht an einem Speichermodul, einem Prozessor oder anderen Komponenten an.
Abbildung 115. Einsetzen der Systemplatine Nächste Schritte 1. Installieren Sie die folgenden Komponenten: a. Trusted Platform Module (TPM) ANMERKUNG: Das TPM-Modul muss nur bei Installation einer neuen Systemplatine ausgetauscht werden. 2. 3. 4. 5. 6. 138 ANMERKUNG: Das TPM-Plug-in-Modul ist mit der Systemplatine verbunden und kann nicht entfernt werden. Für den Austausch einer Systemplatine, auf der ein TPM-Plug-in-Modul installiert war, wird stets ein Ersatz-TPM-Plug-in-Modul bereitgestellt. b.
b. Geben Sie die Service-Tag-Nummer manuell ein, wenn sie nicht im Backup-Flash-Gerät gesichert wurde. Weitere Informationen finden Sie unter Manuelles Aktualisieren der Service-Tag-Nummer. c. Aktualisieren Sie die BIOS- und iDRAC-Versionen. d. Aktivieren Sie erneut das Trusted Platform Module (TPM). Weitere Informationen finden Sie unter Aktualisieren des Trusted Platform Module (TPM). 7. Importieren Sie Ihre neue oder vorhandene Lizenz für iDRAC Enterprise.
5 Jumper und Anschlüsse Dieses Thema enthält spezifische Informationen über die Jumper. Außerdem finden Sie hier einige grundlegende Informationen zu Jumpern und Switches und die Anschlüsse auf den verschiedenen Platinen im System. Mit den Jumpern auf der Systemplatine können System- und Setup-Kennwörter deaktiviert werden. Sie müssen die Anschlüsse auf der Systemplatine kennen, um Komponenten und Kabel korrekt zu installieren.
Systemplatinenanschlüsse Abbildung 116. Systemplatinenanschlüsse Tabelle 20.
Tabelle 20.
Tabelle 20.
Voraussetzungen VORSICHT: Manche Reparaturarbeiten dürfen nur von qualifizierten Servicetechnikern durchgeführt werden. Maßnahmen zur Fehlerbehebung oder einfache Reparaturen sollten Sie nur dann selbst durchführen, wenn dies laut Produktdokumentation genehmigt ist, oder wenn Sie vom Team des Online- oder Telefonsupports dazu aufgefordert werden. Schäden durch nicht von Dell genehmigte Wartungsarbeiten werden durch die Garantie nicht abgedeckt.
6 Systemdiagnose und Anzeigecodes Die Diagnoseanzeigen auf der Vorderseite geben beim Systemstart den Status des Systems wieder. Themen: • • • • • • • • Status-LED-Anzeigen Anzeigecodes für Systemzustand und System-ID iDRAC Quick Sync 2-Anzeigecodes iDRAC Direct-LED-Anzeigecodes NIC-Anzeigecodes Netzteil-Anzeigecodes Laufwerksanzeigecodes Systemdiagnose Status-LED-Anzeigen ANMERKUNG: Die Anzeigen leuchten stetig gelb, wenn ein Fehler auftritt. Tabelle 22.
Tabelle 22. LED-Statusanzeigen und Beschreibungen (fortgesetzt) Symb ol Beschreibun Zustand g Fehlerbehebung PCIe-Anzeige Die Anzeige blinkt gelb, wenn ein Fehler bei einer PCIe-Karte aufgetreten ist. Starten Sie das System neu. Aktualisieren Sie ggf. erforderliche Treiber für die PCIe-Karte. Setzen Sie die Karte wieder ein. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt Wie Sie Hilfe bekommen.
Tabelle 24. iDRAC Quick Sync 2-Anzeigen und Beschreibungen (fortgesetzt) Anzeigecode Beschreibung Fehlerbehebung Stetig weiß leuchtend Zeigt an, dass iDRAC Quick Sync 2 zur Übertragung bereit ist. Drücken Sie auf die iDRAC Quick Sync 2-Taste, um die Funktion zu starten. Wenn sich die LED nicht ausschalten lässt, starten Sie das System neu. Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt Wie Sie Hilfe bekommen. Schnell weiß blinkend Weist auf Datenübertragungsaktivität hin.
Abbildung 119. NIC-Anzeigecodes 1. LED-Verbindungsanzeige 2. LED-Aktivitätsanzeige Tabelle 26. NIC-Anzeigecodes Status Zustand Verbindungsanzeige und Aktivitätsanzeige leuchten nicht. Die NIC ist nicht mit dem Netzwerk verbunden. Die Verbindungsanzeige leuchtet grün und die Aktivitätsanzeige blinkt grün. Der NIC ist mit einem gültigen Netzwerk bei seiner maximalen PortGeschwindigkeit verbunden und es werden Daten gesendet oder empfangen.
Tabelle 27. Codes für die Statusanzeige des Wechselstromnetzteils Betriebsanzeigeco des Zustand Grün Eine zulässige Stromquelle ist mit dem Netzteil verbunden und das Netzteil ist in Betrieb. Gelb blinkend Zeigt ein Problem mit dem Netzteil an. Nicht leuchtend Das Netzteil ist nicht an eine Stromquelle angeschlossen. Grün blinkend Wenn die Firmware des Netzteils aktualisiert wird, blinkt der Netzteilgriff grün. VORSICHT: Trennen Sie während der Aktualisierung der Firmware nicht das Netzkabel bzw.
Abbildung 121. Laufwerkanzeigen auf dem Laufwerk und der Festplattenträger an der Rückwandplatine 1. LED-Laufwerksaktivitätsanzeige 2. LED-Laufwerksstatusanzeige 3. Kennzeichnung der Laufwerkskapazität ANMERKUNG: Wenn sich das Laufwerk im AHCI-Modus (Advanced Host Controller Interface) befindet, funktioniert die LEDStatusanzeige nicht und bleibt aus. Tabelle 28.
● Gründliche Tests durchführen, um weitere Testoptionen für Zusatzinformationen über die fehlerhaften Geräte zu erhalten ● Statusmeldungen anzeigen, die angeben, ob Tests erfolgreich abgeschlossen wurden ● Fehlermeldungen über Probleme während des Testvorgangs anzeigen Ausführen der integrierten Systemdiagnose vom Start-Manager Führen Sie die integrierte Systemdiagnose (ePSA) durch, wenn Ihr System nicht startet. Schritte 1. Wenn das System startet, drücken Sie die Taste F11. 2.
7 Wie Sie Hilfe bekommen Themen: • • • • • Kontaktaufnahme mit Dell Feedback zur Dokumentation Zugriff auf Systeminformationen mithilfe von QRL Automatische Unterstützung mit SupportAssist Informationen zum Recycling oder End-of-Life-Service Kontaktaufnahme mit Dell Dell stellt verschiedene online-basierte und telefonische Support- und Serviceoptionen bereit.
Der QRL umfasst die folgenden Informationen zu Ihrem System: ● Anleitungsvideos ● Referenzmaterialien, einschließlich dem Benutzerhandbuch, eine LCD-Diagnose und eine mechanische Übersicht ● Eine direkte Verbindung zu Dell für die Kontaktaufnahme mit dem technischen Support und den Vertriebsteams Schritte 1. Rufen Sie www.dell.com/qrl auf und navigieren Sie zu Ihrem spezifischen Produkt oder 2. Verwenden Sie Ihr Smartphone bzw.
Die Vorteile können je nach für das Gerät erworbener Dell EMC Serviceberechtigung variieren. Weitere Informationen über SupportAssist erhalten Sie auf www.dell.com/supportassist. Informationen zum Recycling oder End-of-Life-Service In bestimmten Ländern werden Rücknahme- und Recyclingservices für dieses Produkt angeboten. Wenn Sie Systemkomponenten entsorgen möchten, rufen Sie www.dell.com/recyclingworldwide auf und wählen Sie das entsprechende Land aus.
8 Dokumentationsangebot In diesem Abschnitt finden Sie Informationen zum Dokumentationsangebot für Ihr System. So zeigen Sie das Dokument an, dass in der Tabelle der Dokumentationsressourcen aufgeführt ist: ● Über die Dell EMC Support-Website: 1. Klicken Sie auf den Dokumentations-Link in der Spalte Standort der Tabelle. 2. Klicken Sie auf das benötigte Produkt oder die Produktversion. ANMERKUNG: Den Produktnamen und das Modell finden Sie auf der Vorderseite des Systems. 3.
Tabelle 29. Dokumentationsangebot (fortgesetzt) Task Dokument Speicherort Informationen über das Installieren des Betriebssystems finden Sie in der Dokumentation zum Betriebssystem. https://www.dell.com/operatingsystemmanuals Weitere Informationen über das Aktualisieren von Treibern und Firmware finden Sie im Abschnitt „Methoden zum Herunterladen von Firmware und Treibern“ in diesem Dokument. www.dell.