Setup Guide
Table Of Contents
- Rack Installation Guide
- Contents
- Four-Post Rack Installation
- Safety Instructions
- General Installation Instructions
- Removing the Rack Doors
- Marking the Rack
- Configuring the Sliding Rail Assemblies (Sliding Rail Kits Only)
- Installing Chassis Static Rail Modules (Static Rail Kits Only)
- Installing the Mounting Rails in the Rack
- Installing the System in the Rack
- Replacing the Rack Doors
- Installing the Tray and Cable-Management Arm (Sliding Rail Kits Only)
- Removing the System From the Rack
- Two-Post Rack Installation
- Index
- Guide d'installation du rack
- Sommaire
- Installation dans un rack à quatre montants
- Consignes de sécurité
- Consignes générales d'installation
- Retrait des portes du rack
- Marquage du rack
- Configuration des assemblages à glissière (kits avec rails coulissants uniquement)
- Installation des modules de rails statiques pour le châssis (kits avec rails statiques uniquement)
- Installation des rails de montage dans le rack
- Installation du système dans l'armoire rack
- Remise en place des portes du rack
- Installation du chemin de câbles et du passe-câbles (kits avec rails coulissants uniquement)
- Retrait du système de l'armoire rack
- Installation dans un rack à deux montants
- Index
- Rack-Installationsanleitung
- Inhalt
- Montage in einem Rack mit vier Stützen
- Sicherheitshinweise
- Allgemeine Installationsanleitung
- Abnehmen der Rack-Türen
- Markieren des Racks
- Konfiguration der Gleitschienensätze (nur bei Kits mit Gleitschienen)
- Installation der festen Schienenmodule am Gehäuse (nur bei Kits mit festen Schienen)
- Installation der Montageschienen im Rack
- Installation des Systems im Rack
- Wiederanbringen der Rack-Türen
- Installation der Ablage und des Kabelführungsarms (nur bei Kits mit Gleitschienen)
- Entfernen des Systems aus dem Rack
- Montage in einem Zwei-Stützen-Rack
- Index
- ラック取り付けガイド
- Guía de instalación del rack
- Contenido
- Instalación del rack de cuatro postes
- Instrucciones de seguridad
- Instrucciones generales de instalación
- Extracción de las puertas del rack
- Marcado del rack
- Configuración de los ensamblajes de rieles deslizantes (únicamente en los kits de rieles deslizantes)
- Instalación de los módulos de rieles estáticos del chasis (únicamente en los kits de rieles estáticos)
- Instalación de los rieles de montaje en el rack
- Instalación del sistema en el rack
- Colocación de las puertas del rack
- Instalación de la bandeja y el brazo para tendido de cables (únicamente en los kits de rieles deslizantes)
- Extracción del sistema del rack
- Instalación del rack de dos postes
- Índice
Two-Post Rack Installation 37
Installing the System in the Rack
CAUTION: If you are installing more than one system, install the first system in the lowest available position
in the rack.
1
Place one hand on the front-bottom of the system and the other hand on the back-bottom of the
system.
2
Lift the system into position so that the side rails at the back of the system are aligned with the
mounting rails in the rack.
CAUTION: Because of the size and weight of the system, never attempt to install the system in the mounting rails
by yourself.
3
Push the system into the mounting rails until the system stops.
4
Push in and turn the thumbscrews on each side of the front chassis panel to secure the system to the
rack.
Removing the System From the Rack
To remove the system from the rack, perform the following procedure:
1
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
2
Loosen the thumbscrews on each side of the front chassis panel that secures the system to the rack.
3
Disconnect all cables from the system.
4
Pull the system out of the rack until it stops because of the release latches.
5
Push down on the release latches on each side of the system (see Figure 1-10).
6
Pull the system completely out of the rack.