Information Update Memory Module Installation Guidelines The following information updates the memory module installation guidelines. • If only DIMM_1 is installed in your system, its capacity must be 512 MB or 1 GB. A single 2-GB DIMM installation is not supported. SATA Optical Drive Support in SUSE Linux SUSE® Linux Enterprise Server 10 Service Pack 1 does not support internal SATA optical drives on systems with more than 4 GB of system memory.
System Board Update Figure 6-1 in the Hardware Owner’s Manual incorrectly illustrated the system jumpers and the PCI slot (slot 3). Figure 1-1 shows the correct illustration. Figure 1-1. System Board Jumpers Expansion Card Update The following updates incorrect expansion card information. The system board can accommodate up to four expansion cards: • One 3.3-V, half-length 32-bit, 33-MHz PCI (slot 3) • One 2.5-Gb/sec PCIe x1 (slot 4) • Two 2.
System Features Update The following system features are new or updated. • A DVD-RW drive has been added to the list of supported optical drives. • The amount of graphics memory for the ATI ES 1000 2D graphics controller is 32 MB instead of 16 MB. Technical Specifications Update A DVD-RW drive has been added to the list of supported optical drives.
信息更新 内存模块安装原则 以下信息是对内存模块安装原则的更新 。 • 如果系统安装 DIMM_1,则其容量必须是 512 MB 或 1 GB。不支持单 个 2 GB DIMM 的安装。 SUSE Linux 中的 SATA 光盘驱动器支持 对于系统内存大于 4 GB 的系统,SUSE® Linux Enterprise Server 10 Service Pack 1 不支持内置 SATA 光盘驱动器。 由于 sata_nv 驱动程序的问题,安装过程中以及安装后无法识别连接至 SATA 控制器的 SATA 光盘驱动器。在将来的服务软件包中将提供对此问 题的修正。 要解决此问题,必须加载 sata_nv 驱动器以及在启动过程中禁用 adma 模式。 将以下文本添加至 /boot/grup/menu.1st 文件中的内核行 sata_nv.adma=0 以下是一个 menu.1st 文件示例: root (hd0,1) kernel /boot/vmlinuz root=/dev/sda2 vga=0x317 resuem=/dev/sda1 splash=silent showopts sata_nv.
系统板更新 硬件用户手册中的图 6-1 所示的系统跳线和 PCI 插槽(插槽 3)有误。 图 1-1 的是正确的图示。 图 1-1. 系统板跳线 扩充卡更新 以下是对扩充卡错误信息的更新。 系统板最多可以容纳四块扩充卡。 • 一个 3.3 V、半长、32 位、33 MHz PCI(插槽 3) • 一个 2.5-Gb/ 秒 PCIe x1(插槽 4) • 两个 2.
系统功能更新 以下为新增的或更新的系统功能。 • 支持的光盘驱动器列表中增加了 DVD-RW 驱动器。 • ATI ES 1000 2D 图形控制器的图形内存是 32 MB 而非 16 MB。 技术规格更新 支持的光盘驱动器列表中增加了 DVD-RW 驱动器。 驱动器 光盘驱动器 最多两个可选的内置 DVD-ROM、组合 CD-RW/DVD 或 DVD-RW 光盘驱动器 (仅限 SATA 接口) 注:DVD 设备仅用于数据。 系统的物理尺寸已更正如下。 物理规格 高度 41.3 厘米(16.25 英寸) 宽度 18.7 厘米(7.36 英寸) 厚度 45.8 厘米(18 英寸) 重量(最大配置) 13 千克(28.6 磅) ___________________ 本说明文件中的信息如有更改,恕不另行通知。 © 2007 – 2008 Dell Inc. 版权所有,翻印必究。 未经 Dell Inc. 书面许可,严禁以任何形式进行复制。 本文使用的商标:Dell 、Dell 徽标和 PowerEdge 是 Dell Inc. 的商标; SUSE 是 Novell Inc.
Mise à jour des informations Consignes d'installation des barrettes de mémoire Les informations suivantes mettent à jour les consignes d'installation du module de mémoire. • Si seule la barrette DIMM_1 est installée dans le système, elle doit avoir une capacité de 512 Mo ou de 1 Go. L'installation d'une seule barrette DIMM de 2 Go n'est pas prise en charge.
Mise à jour de la carte système L'illustration des cavaliers de la carte système et du logement PCI (logement 3) de la figure 6-1 du manuel du propriétaire était incorrecte. La figure 1-1 montre l'illustration correcte. Figure 1-1. Cavaliers de la carte système Mise à jour de la carte d'extension Les informations correctes concernant la carte d'extension sont indiquées ci-dessous.
Mise à jour des caractéristiques du système Les caractéristiques suivantes du système sont nouvelles ou ont été mises à jour. • Un lecteur DVD-RW a été ajouté à la liste des lecteurs optiques pris en charge. • La mémoire graphique de la carte graphique ATI ES 1000 2D est désormais 32 Mo au lieu de 16 Mo. Mise à jour des spécifications techniques Un lecteur DVD-RW a été ajouté à la liste des lecteurs optiques pris en charge.
Aktuelle Informationen Installationsrichtlinien für Speichermodule Die nachstehenden Hinweise ergänzen die Anweisungen für die Installation von Speichermodulen. • Wenn nur DIMM_1 im System installiert ist, muss die Kapazität 512 MB oder 1 GB betragen. Die Installation eines einzelnen 2-GB-DIMM wird nicht unterstützt.
Aktualisierung der Informationen zur Systemplatine Auf Abbildung 6-1 im Hardware-Benutzerhandbuch sind die System-Jumper und der PCI-Steckplatz (Steckplatz 3) falsch dargestellt. Abbildung 1-1 zeigt die korrekte Darstellung. Abbildung 1-1.
Aktualisierung der Informationen zur Erweiterungskarte Die nachstehenden Hinweise korrigieren fehlerhafte Informationen zu den Erweiterungskarten.
Aktualisierung der technischen Daten Die Liste der unterstützten optischen Laufwerke wurde um ein DVD-RWLaufwerk erweitert. Laufwerke Optische Laufwerke Bis zu zwei optionale interne SATALaufwerke vom Typ DVD-ROM, CDRW/DVD-Combo oder DVD-RW (nur SATA-Schnittstelle) ANMERKUNG: DVD-Geräte sind reine Datenlaufwerke.
アップデート情報 メモリモジュール取り付けガイドライン 以下は、メモリモジュールの取り付けガイドラインに関するアップデー ト情報です。 • お使いのシステムに DIMM_1 のみを取り付ける場合、メモリモ ジュールの容量は 512 MB または 1 GB でなければなりません。 2 GB DIMM を 1 枚だけ取り付ける構成はサポートされていません。 SUSE Linux における SATA オプティカルドラ イブのサポート 4 GB を超えるシステムメモリを搭載したシステムに SUSE® Linux Enterprise Server 10 Service Pack 1 をインストールした場合、内蔵 SATA オプティカルドライブはサポートされません。 SATA コントローラに接続されている SATA オプティカルドライブは、 インストール中もインストール後も認識されません。これは、sata_nv ドライバの問題が原因です。この問題を修正するパッチは、将来のサー ビスパックで用意される見込みです。 この問題を回避するには、起動中に adma モードを無効にした状態で、 sata_nv ドライバをロード
システム基板に関するアップデート情報 『ハードウェアオーナーズマニュアル』の図 6-1 では、システムジャン パと PCI スロット(スロット 3)の位置が間違っていました。図 1-1 が 正しい図です。 図 1-1 システム基板のジャンパ 拡張カードに関するアップデート情報 以下は、拡張カードに関する情報の訂正です。 システム基板には、次の構成で拡張カードを 4 枚まで取り付けること ができます。 • 3.3 V、ハーフレングス 32 ビット、33 MHz PCI カード 1 枚 (スロット 3) • 2.5 Gb/ 秒 PCIe x1 カード 1 枚(スロット 4) • 2.
システムの機能に関するアップデート情報 以下のシステム機能が追加または更新されています。 • サポートされるオプティカルドライブのリストに DVD-RW ドライブ が追加されました。 • ATI ES 1000 2D グラフィックコントローラのグラフィックメモリの 容量が、従来の 16 MB から 32 MB に増えました。 仕様に関するアップデート情報 サポートされるオプティカルドライブのリストに DVD-RW ドライブが 追加されました。 ドライブ オプティカルドライブ オプションの内蔵 DVD-ROM、CDRW/DVD コンボドライブ、または DVD-RW オプティカルドライブ (SATA インタフェースのみ)2 台まで メモ:DVD デバイスはデータ専用。 システムのサイズと重量は、正しくは以下のとおりです。 サイズと重量 縦幅 41.3 cm 横幅 18.7 cm 奥行 45.8 cm 重量(最大構成) 13 kg ___________________ 本書の内容は予告なく変更されることがあります。 © 2007 ~ 2008 すべての著作権は Dell Inc.
정보 갱신본 메모리 모듈 설치 지침 다음 정보는 메모리 모듈 설치 지침을 업데이트합니다. • DIMM_1만 시스템에 설치되어 있을 경우 용량은 512 MB 또는 1 GB이 어야 합니다. 2-GB DIMM은 하나만 설치할 수 없습니다. SUSE Linux에서의 SATA 광학 드라이브 지원 SUSE® Linux Enterprise Server 10 Service Pack 1은 시스템 메모리가 4GB 이상 장착된 시스템의 내장형 SATA 광학 드라이브를 지원하지 않습니다. SATA 컨트롤러에 연결된 SATA 광학 드라이브는 sata_nv 드라이버 문제로 인해 설치 도중이나 설치 후에도 인식되지 않습니다. 이 문제에 대한 해결 방법이 추후 서비스 팩을 통해 제공됩니다. 이 문제를 해결하려면 부팅하는 도중 adma 모드가 비활성화된 상태에서 sata_nv 드라이버를 로드해야 합니다. 다음 텍스트를 /boot/grup/menu.1st 파일의 커널 라인에 추가하십시오. sata_nv.adma=0 다음은 menu.
시스템 보드 업데이트 하드웨어 소유자 설명서의 그림 6-1은 잘못된 시스템 점퍼 및 PCI 슬롯 (슬롯 3)을 설명하고 있습니다. 그림 1-1이 올바른 설명을 보여 줍니다. 그림 1-1. 시스템 보드 점퍼 확장 카드 업데이트 다음은 잘못된 확장 카드 정보를 업데이트합니다. 시스템 보드는 최대 4 개의 확장 카드를 수용할 수 있습니다 . • 3.3V, 절반 길이, 32비트, 33MHz PCI(슬롯 3) 1개 • 2.5-Gb/sec PCIe x1(슬롯 4) 1개 • 2.
시스템 특징 업데이트 다음과 같은 시스템 특징이 새로 제공되거나 업데이트됩니다. • DVD-RW 드라이브가 지원되는 광학 드라이브 목록에 추가되었습 니다. • ATI ES 1000 2D 그래픽 컨트롤러의 그래픽 메모리 양은 16MB 대신 32MB입니다. 기술 사양 업데이트 DVD-RW 드라이브가 지원되는 광학 드라이브 목록에 추가되었습니다. 드라이브 광학 드라이브 내장형 DVD-ROM, CD-RW/DVD 콤보 드라이브 또는 DVD-RW 광학 드라이브 (SATA 인터페이스 전용 ) 옵션 최대 2 개 주 : DVD 장치는 데이터 전용입니다 . 시스템 규격은 다음과 같이 수정되었습니다 . 규격 높이 41.3cm(16.25 인치 ) 너비 18.7cm(7.36 인치 ) 깊이 45.8cm(18 인치 ) 무게 ( 최대 구성시 ) 13kg(28.6lb) ___________________ 이 문서의 정보는 사전 통보 없이 변경될 수 있습니다 . © 2007–2008 Dell Inc.
Actualización de información Pautas para la instalación de módulos de memoria La información siguiente es una actualización de las pautas para la instalación de módulos de memoria. • Si el sistema sólo tiene instalado un DIMM_1, su capacidad debe ser de 512 MB o 1 GB. No se admite la instalación de un único DIMM de 2 GB.
Actualización de la placa base En la ilustración 6-1 del Manual del propietario del hardware se identifican incorrectamente los puentes del sistema y la ranura PCI (ranura 3). En la ilustración 1-1 se muestra el contenido correcto. Ilustración 1-1. Puentes de la placa base Actualización de la tarjeta de expansión La información siguiente actualiza los datos incorrectos sobre la tarjeta de expansión.
Actualización de los componentes del sistema Los componentes del sistema siguientes son nuevos o se han actualizado. • Se ha añadido una unidad de DVD-RW a la lista de unidades ópticas admitidas. • La cantidad de memoria gráfica para la controladora gráfica ATI ES1000 en 2D es 32 MB en lugar de 16 MB. Actualización de las especificaciones técnicas Se ha añadido una unidad de DVD-RW a la lista de unidades ópticas admitidas.