Integrated Dell Remote Access Controller 8 (iDRAC8) et iDRAC7 Guide d'utilisation v2.20.20.
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION indique un risque d'endommagement du matériel ou de perte de données et vous indique comment éviter le problème. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessures corporelles ou même de mort. Copyright © 2015 Dell Inc. Tous droits réservés.
Table des matières 1 Présentation......................................................................................................... 17 Avantages de l'utilisation d'iDRAC avec Lifecycle Controller.............................................................17 Fonctions clés......................................................................................................................................18 Nouveautés de cette version....................................................................
Modification du mot de passe d'ouverture de session par défaut à l'aide de l'interface Web................................................................................................................................................ 45 Modification du mot de passe d'ouverture de session par défaut à l'aide de RACADM............ 45 Modification du mot de passe de connexion par défaut à l'aide de l'utilitaire Paramètres iDRAC...................................................................................
Affichage et gestion des mises à jour intermédiaires à l'aide de RACADM.................................87 Restauration du micrologiciel du périphérique................................................................................. 87 Restauration du micrologiciel à l'aide de l'interface Web d'iDRAC.............................................88 Restauration du micrologiciel à l'aide de l'interface Web CMC..................................................
Définition du premier périphérique de démarrage..........................................................................106 Définition du premier périphérique de démarrage à l'aide de l'interface Web........................ 106 Définition du premier périphérique de démarrage à l'aide de RACADM.................................. 107 Définition du premier périphérique de démarrage à l'aide de la console virtuelle.................. 107 Activation du dernier écran de blocage.....................................
Configuration du seuil d’avertissement de température d’entrée............................................. 131 Affichage des interfaces réseau disponibles sur le SE hôte.............................................................132 Affichage des interfaces réseau disponibles sur le SE hôte à l’aide de l’interface Web............132 Affichage des interfaces réseau disponibles sur le SE hôte à l’aide de RACADM.....................
Présentation d'Active Directory avec le schéma standard........................................................ 162 Configuration d'Active Directory avec le schéma standard...................................................... 164 Présentation d'Active Directory avec schéma étendu............................................................... 167 Configuration du schéma étendu Active Directory................................................................... 169 Test des paramètres Active Directory........
Filtrage des alertes à l'aide de l'interface RACADM....................................................................193 Définition d'alertes d'événement......................................................................................................193 Définition d'alertes d'événements à l'aide de l'interface Web................................................... 193 Définition d'alertes d'événement à l'aide de l'interface RACADM.............................................
Définition du seuil d’avertissement de consommation d'énergie à l’aide de l’interface Web.. 211 Exécution d'opérations de contrôle de l'alimentation.....................................................................212 Exécution des opérations de contrôle de l'alimentation à l'aide de l'interface Web................212 Exécution d'opérations de contrôle de l'alimentation à l'aide de l'interface RACADM............212 Plafonnement de l'alimentation............................................................
Inventaire et surveillance des périphériques de stockage.............................................................. 246 Surveillance des périphériques de stockage à l'aide de l'interface Web ..................................247 Surveillance d'un périphérique de stockage à l'aide de l'interface RACADM........................... 247 Surveillance d'un fond de panier à l'aide de l’utilitaire de paramètres d'iDRAC....................... 247 Affichage de la topologie des périphériques de stockage.............
Affichage et application des opérations en attente à l’aide de RACADM.................................280 Périphériques de stockage : scénarios d'opérations d’application ...............................................
Lancement de Média Virtuel sans utiliser la console virtuelle...................................................301 Ajout d'images Média Virtuel...................................................................................................... 302 Affichage des informations détaillées d'un périphérique virtuel...............................................303 Réinitialisation USB.....................................................................................................................
Exemples d'utilisation........................................................................................................................327 Gestion de l'alimentation du serveur......................................................................................... 328 Gestion du journal SEL................................................................................................................328 Navigation dans la cible MAP......................................................................
Installation d'un système d'exploitation depuis plusieurs disques............................................350 Déploiement d'un système d'exploitation intégré sur une carte SD...............................................351 Activation du module SD et de la redondance dans le BIOS.................................................... 351 23 Dépannage d'un système géré à l'aide d'iDRAC....................................... 352 Utilisation de la console de diagnostic........................................
Périphériques de stockage................................................................................................................377 iDRAC Service Module...................................................................................................................... 377 RACADM........................................................................................................................................... 380 Divers........................................................................
Présentation 1 iDRAC (Integrated Dell Remote Access Controller) a pour vocation d'améliorer la productivité des administrateurs et la disponibilité générale des serveurs Dell. iDRAC signale aux administrateurs les incidents des serveurs, les aide à gérer à distance les serveurs et réduit le besoin d'accéder physiquement au serveur.
• Amélioration de la productivité et réduction du coût total de possession : comme les administrateurs peuvent accéder à un plus grand nombre de serveurs distants, le personnel informatique est plus productif et les coûts opérationnels, tels que les déplacements, sont réduits. • Environnement sécurisé : en fournissant un accès sécurisé aux serveurs distants les administrateurs peuvent exécuter des fonctions de gestion importantes sans affecter la sécurité des serveurs et du réseau.
• Déploiement de systèmes d'exploitation en utilisant le partage de fichier à distance, média virtuel et VMCLI. • Activation de l'auto-détection. • Effectuez la configuration du serveur à l'aide de la fonction d'exportation ou d'importation du profil XML via RACADM et WS-MAN. Pour en savoir plus, voir le Lifecycle Controller Remote Services Quick Start Guide (Guide de démarrage rapide des services à distance du Lifecycle Controller).
• Configurer l’iDRAC à l’aide des Profils de configuration de serveur sur le périphérique USB. Maintenance et dépannage • Exécution d'opérations d'alimentation et surveillance de la consommation d'énergie. • Optimisez les performances du système et la consommation d’énergie en modifiant les paramètres thermiques. • Aucune dépendance de l'administrateur de serveur pour la génération d'alertes.
• Modification du mot de passe d'ouverture de session par défaut. • Définissez les mots de passe utilisateur et les mots de passe du BIOS en utilisant un format crypté unidirectionnel pour une sécurité renforcée. • Interfaces SMCLP et Web prenant en charge le cryptage 128 bits et 40 bits (dans les pays où le cryptage 128 bits n'est pas accepté) à l'aide de la norme SSL 3.
• Safari Pour consulter la liste des versions, voir le fichier iDRAC8 Release Notes (Notes de mise à jour iDRAC8) disponible à l'adresse dell.com/idracmanuals. Gestion des licences Les fonctions iDRAC sont disponibles en fonction de la licence (Gestion de base, iDRAC Express ou iDRAC Enterprise) achetée.
• Importer : après l'acquisition d'une licence, stockez la licence dans un emplacement de stockage local et importez-la vers iDRAC en utilisant l'une des interfaces prises en charge. La licence est importée si les vérifications de validation auxquelles elle est soumise aboutissent. REMARQUE : Pour un nombre limité de fonctions, il est nécessaire de redémarrer le système pour activer les fonctions.
État/Condition ou état du composant Importer Exportation Supprimer Remplacer En savoir plus Licence expirée Non Oui Oui Oui Oui License installée, mais composant manquant Oui Oui Non Oui Non REMARQUE : Dans l’interface Web iDRAC, sur la page Licences, développez le périphérique afin de voir l’option Remplacer dans le menu déroulant.
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Telnet Non Oui Oui Oui Oui Oui Oui Oui SSH Non Oui Oui Oui Oui Oui Oui Oui WS-MAN Oui Oui Oui Oui Oui Oui Oui Oui Non Oui Oui Oui Oui Oui Oui NTP (Protocole de Non temps du réseau) Connectivité Carte d’interface réseau partagée (LOM) Oui Oui Oui Oui S/O S/O Oui Oui NIC2 dédié Non Oui
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Services de répertoire (AD, LDAP) .
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Discussion console virtuelle Non Non Non Non Non Non Oui Oui Partitions Virtual Flash Non Non Non Non Non Non Oui Oui 1.
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Surveillance de panne prédictive Non Oui Non Oui Non Oui Non Oui SNMP v1, v2 et v3 (interruptions et gets) Non Oui Oui Oui Oui Oui Oui Oui Alertes par e-mail Non Non Oui Oui Oui Oui Oui Oui Seuils configurables Non Oui Non Oui Non Oui Non Oui Surveillance du ventilateur Non Oui Non Oui No
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Synchroniser avec une logithèque (mises à jour planifiées) Non Non Non Non Non Non Oui Oui Mise à jour automatique Non Non Non Non Non Non Non Oui Déploiement et configuration Outils de Non déploiement du SE intégrés Oui Non Oui Non Oui Non Oui Outils de configuration intégrés (utilitaire de paramètres
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Système hors service/recyclé Non Non Oui Non Oui Non Oui Oui Diagnostics, Service et Journalisation Outils de Oui diagnostic intégrés Oui Oui Oui Oui Oui Oui Oui Remplacement de pièce Non Oui Oui Oui Oui Oui Oui Oui Sauvegarde de la configuration du serveur Non Non Non Non Non Non Oui Oui Resta
Fonction Gestio iDRAC n de 8 Basic base (iDRA C7) iDRAC 7 Expres s iDRAC 8 Expres s iDRAC 7 Expre ss pour lames iDRAC8 Express pour lames iDRAC7 Enterprise iDRAC8 Enterprise Capture à l'amorçage Non Non Non Non Non Non Oui Oui Réinitialisation manuelle de l’iDRAC Non Oui Non Oui Non Oui Non Oui NMI virtuel Non Oui Non Oui Non Oui Non Oui Surveillance du SE Non Oui Non Oui Non Oui Non Oui Rapport d'intégrité Non intégré Oui Non Oui Non Oui Non Oui Journal d
Tableau 2. Interfaces et protocoles d'accès à iDRAC Interface ou protocole Description Utilitaire iDRAC Settings (Configuration iDRAC) Utilisez l'utilitaire Paramètres iDRAC pour exécuter des opérations de pré-système d'exploitation. Il inclut un sous-groupe de fonctions disponibles dans l'interface Web d'iDRAC et d'autres fonctions. Interface Web d'iDRAC Utilisez l'interface Web d'iDRAC pour gérer l'iDRAC et surveiller le système géré. Le navigateur se connecte au serveur Web via le port HTTPS.
Interface ou protocole Description • • • • • mettre à jour le micrologiciel iDRAC configurer les paramètres réseau iDRAC vous connecter à l'interface Web iDRAC démarrer, arrêter ou réinitialiser le système géré ; mettre à jour le BIOS, PERC et les adaptateurs réseau pris en charge. Lifecycle Controller Utilisez le Lifecycle Controller pour configurer les iDRAC.
Interface ou protocole Description la fonctionnalité LC-Remote Services. Vous pouvez également utiliser Power Shell et Python pour exécuter des scripts vers l'interface WS-MAN. Web Services for Management (WS-Management) est un protocole SOAP (Simple Object Access Protocol) qui permet de gérer les systèmes. L'iDRAC utilise WS– Management pour transporter les informations de gestion CIM (Common Information Model) DMTF (Distributed Management Task Force).
Numéro de port Fonction 5901 VNC Lorsque la fonctionnalité VNC est activée, le port 5901 s'ouvre. * Port configurable La liste suivante répertorie les ports qu'iDRAC utilise comme client. Tableau 4.
• Le Dell Lifecycle Controller Graphical User Interface For 13th Generation Dell PowerEdge Servers User’s Guide (Guide d'utilisation de l'interface utilisateur graphique du Dell Lifecycle Controller pour les serveurs Dell PowerEdge de 13e génération) fournit des informations sur l’utilisation de l’interface utilisateur graphique (GUI) du Lifecycle Controller.
Pour consulter des documents concernant iDRAC ou d'autres micrologiciels associés, voir dell.com/ esmmanuals. Contacter Dell REMARQUE : Si vous ne disposez pas d'une connexion Internet, les informations de contact figurent sur la facture d'achat, le borderau de colisage, la facture le catalogue des produits Dell. Dell propose diverses options d'assistance et de maintenance en ligne et téléphonique.
• Avec les moteurs de recherche : – Saisissez le nom et la version du document dans la zone de recherche .
Ouverture de session dans iDRAC 2 Vous pouvez ouvrir une session dans iDRAC comme utilisateur iDRAC, utilisateur Microsoft Active Directory ou utilisateur LDAP. Le nom d'utilisateur et le mot de passe par défaut sont respectivement root et calvin. Vous pouvez également ouvrir la session en utilisant la connexion directe (SSO) ou une carte à puce. REMARQUE : Vous devez disposer du privilège de connexion à iDRAC pour pouvoir ouvrir une session dans iDRAC.
d'utilisateur peut être \, / ou @. Par exemple, dell.com\jean_douart ou JEAN_DOUART@DELL.COM. Si le domaine n'est pas défini dans le nom d'utilisateur, sélectionnez le domaine Active Directory dans le menu déroulant Domaine. 5. Pour un utilisateur LDAP, dans les champs de nom d'utilisateur et de mot de passe, entrez votre nom d'utilisateur et votre mot de passe LDAP. Le nom de domaine n'est pas nécessaire pour la connexion LDAP.
La page Ouverture de session iDRAC qui apparaît vous invite à insérer la carte à puce. REMARQUE : Si le numéro de port HTTPS par défaut (443) a été changé, tapez https://[IP address]:[port number] , où [IP address] est l'adresse IP d'iDRAC et [port number] est le numéro de port HTTPS. 2. Insérez la carte à puce dans le lecteur et cliquez sur Ouvrir une session. Une invite demande le code PIN de la carte. Aucun mot de passe n'est nécessaire. 3.
Concepts connexes Activation ou désactivation de l'ouverture de session par carte à puce Tâches connexes Configuration de la connexion par carte à puce iDRAC pour les utilisateurs Active Directory Ouverture d'une session iDRAC à l'aide de la connexion directe Lorsque la connexion directe (SSO) est activée, vous pouvez ouvrir une session dans iDRAC sans entrer vos références d'utilisateur de domaine, telles que le nom d'utilisateur et le mot de passe.
Pour plus d'informations, voir le Chassis Management Controller User’s Guide (Guide d'utilisation de Chassis Management Controller) disponible à l'adresse dell.com/support/manuals. Accès à l'iDRAC à l'aide de l'interface distante RACADM Vous pouvez utiliser l'interface distante RACADM pour accéder à l'iDRAC à l'aide de l'utilitaire RACADM.
Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC) disponible à l'adresse dell.com/idracmanuals. Accès à l'iDRAC à l'aide de SMCLP SMCLP est l'invite de ligne de commande par défaut lorsque vous ouvrez une session dans l'iDRAC à l'aide de Telnet ou SSH. Pour en savoir plus, voir Utilisation de SMCLP. Connexion à l'iDRAC à l'aide de l'authentification par clé publique Vous pouvez vous connecter à l'iDRAC sur SSH sans entrer de mot de passe.
Modification du mot de passe d'ouverture de session par défaut Le message d'avertissement qui vous permet de modifier le mot de passe par défaut s'affiche si : • Vous vous connectez à iDRAC avec le privilège de Configuration. • La fonction d'avertissement de mot de passe par défaut est activée. • Les coordonnées de tout compte actuellement activé sont root/calvin.
Modification du mot de passe de connexion par défaut à l'aide de l'utilitaire Paramètres iDRAC Pour modifier le mot de passe de connexion par défaut à l'aide de l'utilitaire Paramètres iDRAC : 1. Dans l'utilitaire de configuration iDRAC, accédez à Configuration de l'utilisateur. La page Paramètres iDRAC - Configuration de l'utilisateur s'affiche. 2. Dans le champ Modifier le mot de passe, saisissez le nouveau mot de passe. 3. Cliquez successivement sur Retour, Terminer et Oui.
• Série d’erreurs de connexion et alertes • Augmentation des intervalles de temps à chaque tentative séquentielle de connexion incorrecte • Entrées de journal REMARQUE : Il est possible de consulter les erreurs et alertes de connexion, les augmentations des intervalles à chaque connexion incorrecte et les entrées de journal à l'aide de n'importe laquelle des interfaces iDRAC, notamment l’interface Web, Telnet, SSH, RACADM à distance, WS-MAN et VMCLI. Tableau 6.
Installation du système géré et de la station de gestion 3 Pour pouvoir effectuer la gestion de systèmes hors bande à l'aide d'iDRAC, vous devez configurer l'iDRAC pour l'accès à distance, installer la station de gestion et le système géré et configurer les navigateurs Web compatibles. REMARQUE : S'il s'agit de serveurs lames, installez les modules CMC et E/S dans le châssis et installez physiquement le système dans le châssis avant d'exécuter les configurations.
• Lifecycle Controller (voir le Guide d'utilisation de Lifecycle Controller) • Dell Deployment Toolkit (voir le Guide d'utilisation Dell Deployment Toolkit) • Panneau LCD du châssis ou du serveur (voir le Manuel du propriétaire du matériel) du système REMARQUE : S'il s'agit de serveurs lames, vous pouvez configurer les paramètres réseau à l'aide du panneau LCD du châssis uniquement au cours de la configuration initiale de CMC.
6. • Paramètres IPv6 • Paramètres IPMI • Paramètres VLAN Cliquez successivement sur Retour, Terminer et Oui. Les informations réseau sont enregistrées et le système redémarre. Tâches connexes Paramètres réseau Paramètres communs Paramètres IPv4 Paramètres IPv6 Paramètres IPMI Paramètres VLAN Paramètres réseau Pour configurer les paramètres réseau : REMARQUE : Pour plus d'informations sur les options, voir l'aide en ligne de l'utilitaire de configuration d'iDRAC. 1.
REMARQUE : L'option LOM partagé n’est pas prise en charge sur les cartes bNDC suivantes si elles sont utilisées dans un serveur pleine hauteur - avec deux cartes fille réseau (NDC) parce qu’elles ne prennent pas en charge l’arbitrage de matériel : • 3. bNDC Intel 2P X520-k 2P 10 G • bNDC Emulex OCM14102-N6-D 10 Gbits • bNDC Emulex OCm14102-U4-D 10 Gbits • bNDC Emulex OCm14102-U2-D 10 Gbits • bNDC QLogic QMD8262-k DP 10 G Dans le menu Réseau de basculement, sélectionnez l'une des LOM restantes.
Paramètres communs Si l'infrastructure réseau contient un serveur DNS, enregistrez iDRAC dans le DNS. Il s'agit des paramètres initiaux nécessaires aux fonctions avancées, telles que les services d'annuaires : Active Directory ou LDAP, Connexion directe (SSO) et carte à puce. Pour enregistrer iDRAC : 1. Sélectionnez Enregistrer le DRAC auprès du DNS 2. Entrez le nom DRC DNS. 3.
Paramètres IPMI Pour activer les paramètres IPMI : 1. Sous Enable IPMI Over LAN (Activer IPMI sur LAN), sélectionnez Activé. 2. Sous Channel Privilege Limit (Limite de privilège de canal), sélectionnez Administrateur, Opérateur ou Utilisateur. 3. Dans la zone Encryption Key (Clé de cryptage), entrez la clé de cryptage en utilisant entre 0 et 40 caractères hexadécimaux (sans espaces). Par défaut, la valeur correspond à des zéros.
7. Pour enregistrer les informations réseau, cliquez sur Appliquer. Pour plus d'informations, voir le Chassis Management Controller User’s Guide (Guide d'utilisation de Chassis Management Controller) disponible à l'adresse dell.com/support/manuals. Activation du serveur de provisionnement La fonction de Serveur de provisionnement permet aux serveurs nouvellement installés de découvrir automatiquement la console de gestion à distance qui héberge le serveur de provisionnement.
REMARQUE : L'étape 7 est facultative si l'adresse IP du serveur d'approvisionnement (étape 3) est fournie. Configuration des serveurs et des composants du serveur à l'aide de la Configuration automatique La fonction Configuration automatique configure et met à disposition tous les composants d'un serveur (par exemple, le BIOS, l'iDRAC et PERC) en une seule opération en important automatiquement un profil XML de profil de configuration de serveur (SCP) contenant tous les paramètres configurables.
1. Le nom de fichier spécifié dans l'option DHCP 60. 2. -config.xml : si un nom de fichier n'est pas spécifié dans l'option DHCP 60, utilisez le numéro de service du système pour identifier de manière unique le fichier SCP correspondant au système. Par exemple, CDVH7R1-config.xml 3. -config.xml : si le nom de fichier de l'option 60 n'est pas spécifié et que le fichier -config.
identifier; option myname "-f system_config.xml -i 192.168.0.130 -u user -p password -n cifs -s 2 -d 0 -t 500"; où, -i est l'emplacement du partage de fichiers à distance et -f est le nom de fichier dans la chaîne avec les informations d'identification pour le partage de fichiers à distance. L'option DHCP 60 identifie et associe un client DHCP à un fournisseur particulier. Tout serveur DHCP configuré pour agir sur la base d'un ID de fournisseur du client doit avoir l'option 60 et l'option 43 configurées.
9. Dans la fenêtre DHCP, cliquez avec le bouton droit sur IPv4 et sélectionnez Configurer les options prédéfinies . 10. Dans le menu déroulant Option de classe, sélectionnez iDRAC (créé à l'étape 4), puis cliquez sur Ajouter. 11. Dans la boîte de dialogue Type d'option, entrez les informations suivantes : • Nom : iDRAC • Type de données : chaîne • Code : 060 • Description : identifiant de classe de fournisseur Dell 12. Cliquez sur OK pour revenir à la fenêtre DHCP. 13.
CIFS: -f system_config.xml -i 192.168.1.101 -n cifs_share -s 2 -u -p -d 1 -t 400 Configuration de l'option 43 et de l'option 60 sur Linux Mettez à jour le fichier /etc/dhcpd.conf. Les étapes de configuration des options sont similaires aux étapes réservées à Windows : 1. Mettez de côté un bloc ou pool d'adresses que ce serveur DHCP peut allouer. 2. Définissez l'option 43 et utilisez l'identifiant de classe de fournisseur pour l'option 60. option myname code 43 = text; subnet 192.
REMARQUE : ShutdownType ( -d), Timetowait ( -t) et EndHostPowerState ( -e), sont des attributs facultatifs. Ce qui suit est un exemple de réservation DHCP statique à partir d'un fichier dhcpd.conf : host my_host { hardware ethernet b8:2a:72:fb:e6:56; fixed-address 192.168.0.211; option host-name "my_host"; option myname " -f r630_raid.xml -i 192.168.0.1 -n /nfs -s 0 -d 0 -t 300 "; } REMARQUE : Après avoir modifié le fichier dhcpd.
Activation de la configuration automatique à l'aide de RACADM Pour activer la fonctionnalité Configuration automatique à l'aide de RACADM, utilisez l'objet iDRAC.NIC.AutoConfig. Pour en savoir plus, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de la ligne de commande RACADM iDRAC8).
Utilisez la commande suivante pour inclure le mot de passe crypté dans le profil de configuration de serveur exporté : racadm get -f -l -u -p -t --includePH Vous devez définir l’attribut Salt lorsque le mot de passe crypté est défini. REMARQUE : Les attributs ne s'appliquent pas au fichier de configuration INI.
• Client SSH • TFTP • Dell OpenManage Essentials Concepts connexes Installation et utilisation de l'utilitaire VMCLI Tâches connexes Configuration des navigateurs Web pris en charge Accès à distance à l'iDRAC Pour accéder à distance à l'interface Web iDRAC depuis une station de gestion, veillez à ce que cette dernière soit dans le même réseau qu'iDRAC. Par exemple : • Serveurs lames : la station de gestion doit se trouver dans le même réseau que CMC.
La page Paramètres iDRAC - Configuration de l'utilisateur s'affiche. 2. Spécifiez les informations pour le nom d'utilisateur, les privilèges de l'utilisateur LAN, les privilèges de l'utilisateur du port série et le changement du mot de passe. Pour plus d'informations sur les options, voir l'Aide en ligne de l'utilitaire de configuration d'iDRAC. 3. Cliquez successivement sur Retour, Terminer et Oui. Les paramètres du compte d'administrateur sont définis.
• Optimiser la puissance minimale • Définir la température maximale d'évent • Augmenter la ventilation via une compensation du ventilateur, si nécessaire • Augmenter la ventilation via l’augmentation de la vitesse minimale du ventilateur Modification des paramètres thermiques à l’aide de l’interface Web iDRAC Pour modifier les paramètres thermiques : 1. Dans l'interface Web iDRAC, accédez à Présentation → Matériel → Ventilateurs → Configuration. La page Configuration du ventilateur s’affiche. 2.
– Vitesse de ventilateur moyenne : ramène la vitesse des ventilateurs à une vitesse moyenne. – Haute vitesse de ventilateur : ramène la vitesse des ventilateurs à une vitesse de ventilation maximale. – Vitesse maximale de ventilation : ramène la vitesse des ventilateurs à la vitesse maximale. – Désactivé : le décalage de vitesse de ventilateur est désactivé. Il s’agit de la valeur par défaut. Lorsque cette option est désactivée, le pourcentage ne s’affiche pas.
l'utilisateur. Si les options ne sont pas prises en charge, elles ne s’affichent pas ou vous ne pouvez pas fournir une valeur personnalisée. 3. Cliquez sur Appliquer pour appliquer les paramètres. Le message suivant s'affiche : It is recommended to reboot the system when a thermal profile change has been made. This is to ensure all power and thermal settings are activated. Cliquez sur Redémarrer ultérieurement ou Redémarrer maintenant.
Objet Description Utilisation Exemple Assurez-vous de spécifier la valeur en fonction du type d’objet. Pour en savoir plus, reportez-vous à l'aide RACADM. Pour définir la limite par défaut : racadm set system.thermalsettings.AirE xhaustTemp 255 FanSpeedHig hOffsetVal • • • FanSpeedLow OffsetVal • • • FanSpeedMax OffsetVal • • • 68 L'obtention de cette variable lit la valeur de décalage de vitesse de ventilateur en %PWM pour le paramètre Décalage de vitesse de ventilateur élevée.
Objet Description Utilisation Exemple l'augmentation des vitesses des ventilateurs à la vitesse maximale. racadm set system.thermalsettings FanSpeedOffset 3 FanSpeedMed iumOffsetVa l • • • FanSpeedOff set • • • MFSMaximumL imit L'obtention de cette variable lit la valeur de décalage de vitesse de ventilateur en %PWM pour le paramètre Décalage de vitesse de ventilateur moyenne. Cette valeur dépend du système.
Objet Description Utilisation Exemple MFSMinimumL imit Limite minimum de lecture pour MFS Les valeurs comprises entre 0 et MFSMaximumLimi t Pour afficher la valeur la moins élevée qui peut être définie à l’aide de l’option MinimumFanSpeed : La valeur par défaut est 255 (Aucun) MinimumFanS peed • • • ThermalProf ile • • Permet de configurer la vitesse de ventilateur minimum requise pour que le système puisse fonctionner.
Modification des paramètres thermiques à l'aide de l'utilitaire de paramètres d'iDRAC Pour modifier les paramètres thermiques : 1. Dans l'utilitaire de configuration d'iDRAC, accédez à Thermique La page Paramètres thermiques iDRAC s'affiche. 2.
• Contrôles ActiveX reconnus sûrs pour l'écriture de scripts : Activé Téléchargements : • Demander confirmation pour les téléchargements de fichiers : Activé • Téléchargement de fichiers : Activé • Téléchargement de polices : Activé Sous Divers : • Autoriser l'actualisation des métafichiers : Activé • Autoriser les scripts de contrôle du navigateur Web Internet Explorer : Activé • Autoriser les fenêtres initiées par des scripts sans contraintes de taille ou de position : Activé • Ne pas deman
• Afficher les images : sélectionné Sous Sécurité : • Vérifier la révocation des certificats de l'éditeur : désélectionné • Vérifier les signatures des programmes téléchargés : sélectionné • Utiliser SSL 2.0 : désélectionné • Utiliser SSL 3.0 : sélectionné • Utiliser TLS 1.
Pour ajouter l'adresse IP d'iDRAC à la liste des domaines de confiance dans IE8, procédez comme suit : 1. Sélectionnez Outils → Options Internet → Sécurité → Site de confiance → Sites. 2. Entrez l'adresse IP d'iDRAC dans Ajouter ce site Web à la zone. 3. Cliquez successivement sur Ajouter, OK et Fermer. 4. Cliquez sur OK, puis actualisez votre navigateur.
Mise à jour du micrologiciel de périphérique Avec iDRAC, vous pouvez mettre à jour les micrologiciels d'iDRAC, du BIOS et des périphériques pris en charge via la mise à jour Lifecycle Controller, tels que : • Lifecycle Controller • Diagnostics • Pack de pilotes de système d'exploitation • Carte d'interface réseau (NIC) • Contrôleur RAID • Unité d'alimentation (PSU) • Lecteurs SSD (Solid State Drives) PCIe • Disques durs SAS Vous devez mettre à jour le micrologiciel requis vers iDRAC.
Repository Manager User's Guide (Guide d'utilisation de Repository Manager). L'iDRAC fournit automatiquement une différence entre le BIOS et le micrologiciel installé sur le serveur et l'emplacement de l'espace de stockage ou le site FTP. Toutes les mises à jour applicables contenues dans l'espace de stockage s'appliquent au système. Cette fonction est disponible avec la licence iDRAC Enterprise.
** Lorsque l'iDRAC est mis à jour à partir de la version 1.30.30 ou ultérieure, un redémarrage du système n'est pas nécessaire. Cependant, pour les versions de micrologiciel antérieures à l'iDRAC 1.30.30, un redémarrage du système est nécessaire lorsque l'application se fait à l'aide d'interfaces hors bande.
La page Mise à jour de micrologiciel s'affiche. 2. Sur l'onglet Mise à jour , sélectionnez Local comme emplacement des fichiers. 3. Cliquez sur Parcourir, sélectionnez le fichier image du micrologiciel pour le composant requis, puis cliquez sur Téléverser. 4. Une fois le téléversement terminé, la section Détails de la mise à jour affiche chaque fichier de micrologiciel téléversé sur iDRAC et son état.
La page Mise à jour de micrologiciel s'affiche. 2. Sur l'onglet Mise à jour, sélectionnez Partage réseau comme emplacement des fichiers. 3. Dans la section Emplacement du catalogue, entrez les détails de paramétrage du réseau. Lorsque vous indiquez les paramètres de partage du réseau, il est conseillé d’éviter l’utilisation des caractères spéciaux dans le nom d’utilisateur et mot de passe ou de crypter en pourcentage les caractères spéciaux.
3. Dans la section Paramètres du serveur FTP, entrez les détails FTP. Pour plus d'informations sur les champs, voir l'Aide en ligne d'iDRAC. 4. Cliquez sur Vérifier les mises à jour. 5. Une fois le téléversement terminé, la section Détails de la mise à jour affiche un rapport de comparaison montrant les versions actuelles du micrologiciel et les versions de micrologiciel disponibles dans l'espace de stockage.
REMARQUE : Toutes les mises à jour de l'espace de stockage qui ne sont pas applicables au système ou au matériel installé ou qui ne sont pas prises en charge ne sont pas incluses dans le rapport de comparaison. 6. Sélectionnez les mises à jour requises et effectuez l'une des opérations suivantes : • Pour les images de micrologiciel qui ne nécessitent pas un redémarrage du système hôte, cliquez sur Installer (par exemple, le fichier micrologiciel .d7).
• Pour les images de micrologiciel qui ne nécessitent pas un redémarrage du système hôte, cliquez sur Installer (par exemple, le fichier micrologiciel .d7). • Pour les images de micrologiciel qui nécessitent un redémarrage du système hôte, cliquez sur Installer et redémarrer ou Installer au prochain redémarrage. • Pour annuler la mise à jour du micrologiciel, cliquez sur Annuler.
REMARQUE : L'adresse IPv6 n'est pas prise en charge pour programmer les mises à jour automatiques du micrologiciel.
] -time < hh:mm> [-dom < 1 – 28,L,’*’> -wom <1-4,L,’*’> -dow ] -rp <1-366> -a Par exemple : – Pour mettre à jour automatiquement le micrologiciel à l'aide d'un partage CIFS : racadm AutoUpdateScheduler create -u admin -p pwd -l //1.2.3.4/CIFS-share –f cat.xml -time 14:30 -wom 1 -dow sun -rp 5 -a 1 – Pour mettre à jour automatiquement le micrologiciel à l'aide de FTP : racadm AutoUpdateScheduler create -u admin -p pwd -l ftp.mytest.
Le micrologiciel est mis à jour. Il n'est pas nécessaire de redémarrer le système à la fin de la mise à jour. Mise à jour du micrologiciel à l'aide de l'interface RACADM Pour effectuer la mise à jour en utilisant l'interface RACADM : 1. 2. Téléchargez l'image du micrologiciel vers le serveur TFTP ou FTP. Par exemple, C:\downloads \firmimg.
Les mises à jour des composants tels que la PSoC (Programmable System-on-Chip) de module d’E/S exigent que tous les serveurs soient à l’état inactif, la mise à jour est appliquée au cours du prochain cycle de mise sous tension du châssis. Paramétrage du CMC pour effectuer la mise à jour du micrologiciel du CMC depuis l’iDRAC Dans les châssis PowerEdge FX2/FX2s, avant d’effectuer la mise à jour du micrologiciel depuis l’iDRAC pour le CMC et ses composants partagés, procédez comme suit : 1.
Affichage et gestion des mises à jour intermédiaires à l'aide de RACADM Pour afficher les mises à jour intermédiaires à l'aide de RACADM, utilisez la sous-commande jobqueue. Pour en savoir plus, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8) disponible à l'adresse dell.com/ idracmanuals.
• Interface Web iDRAC • Interface Web CMC • CLI RACADM (iDRAC et CMC) • Lifecycle Controller • les services à distance Liffecycle Controller.
Restauration du micrologiciel à l'aide de l'interface Web CMC Pour effectuer la restauration en utilisant l'interface Web CMC : 1. Ouvrez une session dans l'interface Web CMC. 2. Accédez à Présentation du serveur → . La page Condition du serveur s'affiche. 3. Cliquez sur Lancer l'iDRAC et effectuez la restauration du micrologiciel du périphérique tel que mentionné dans la section Restauration du micrologiciel à l'aide de l'interface Web de l'iDRAC.
• Le chargeur de démarrage détecte la carte SD, active le voyant LED fixe orange, lit firmimg.d7, reprogramme iDRAC et démarre iDRAC. Utilisation du serveur TFTP Vous pouvez utiliser le serveur TFTP (Trivial File Transfer Protocol) pour effectuer une mise à niveau vers une version ultérieure ou antérieure du micrologiciel iDRAC ou installer des certificats. Il est utilisé dans les interfaces de ligne de commande SM-CLP et RACADM pour transférer des fichiers vers et depuis l'iDRAC.
Importation du profil du serveur Sauvegarde du profil du serveur à l'aide de l'interface Web iDRAC Pour sauvegarder le profil du serveur à l'aide de l'interface Web iDRAC : 1. Accédez à Présentation générale → Paramètres iDRAC → Profil du serveur. La page Sauvegarde et exportation du profil du serveur s'affiche. 2. Sélectionnez un des éléments suivants pour enregistrer l'image du fichier de sauvegarde : • Réseau pour enregistrer l'image du fichier de sauvegarde sur un partage CIFS ou NFS. 3.
La page Sauvegarde et exportation du profil du serveur s'affiche. 2. Cliquez sur l'onglet de sauvegarde automatique . 3. Sélectionnez l'option Activer la sauvegarde automatique . 4. Sélectionnez un des éléments suivants pour enregistrer l'image du fichier de sauvegarde : • Réseau pour enregistrer l'image du fichier de sauvegarde sur un partage CIFS ou NFS. 5. • vFlash pour enregistrer le fichier image de sauvegarde sur la carte vFlash.
Dans les serveurs de 13e génération, cette fonctionnalité automatise l’ensemble du processus de remplacement de la carte mère. Après le remplacement de la carte mère et la réinstallation de la mémoire, des disques durs et de tout autre matériel, un écran de démarrage spécial s’affiche. Il contient une option de restauration de toutes les configurations enregistrées, du numéro de service, des paramètres de licence et des programmes de diagnostic.
• 6. Supprimer et remplacer : supprime et remplace les informations sur le niveau de RAID, le disque virtuel, les attributs de contrôleur et la configuration du disque dur dans le système à l'aide des données du fichier image de sauvegarde. Cliquez sur Importer. L'importation de profil de serveur est lancée. Importation du profil du serveur à l'aide de RACADM Pour importer le profil du serveur à l'aide de RACADM, utilisez la commande systemconfig restore.
Configuration de l'iDRAC 4 iDRAC permet de configurer les propriétés iDRAC et de définir des utilisateurs et des alertes pour exécuter les tâches de gestion à distance. Avant de configurer l'iDRAC, veillez à configurer les paramètres réseau iDRAC et le navigateur pris en charge et à mettre à jour les licences nécessaires. Pour plus d'informations sur les fonctions utilisables sous licence dans l'iDRAC, voir Gestion de licences.
Concepts connexes Ouverture de session dans iDRAC Modification des paramètres réseau Configuration des services Configuration de l'écran du panneau avant Définition de l'emplacement du système géré Configuration du fuseau horaire et NTP Configuration de la communication iDRAC Configuration des comptes et des privilèges des utilisateurs Surveillance et gestion de l'alimentation Activation du dernier écran de blocage Configuration et utilisation de la console virtuelle Gestion de Média Virtuel Gestion de la c
Controller, Dell Deployment Toolkit et Server Administrator (après avoir démarré dans le système d'exploitation). Pour plus d'informations sur les outils et les paramètres de privilèges, voir les guides d'utilisation correspondants. Pour pouvoir modifier les paramètres réseau à l'aide de l'interface Web d'iDRAC ou RACADM, vous devez disposer des privilèges de Configuration. REMARQUE : La modification des paramètres réseau peut mettre fin aux connexions réseau en cours à iDRAC.
cfgLanNetworking -o cfgNicUseDHCP 0 racadm config -g cfgLanNetworking -o cfgDNSServersFromDHCP 0 racadm config -g cfgLanNetworking -o cfgDNSServer1 192.168.0.5 racadm config -g cfgLanNetworking -o cfgDNSServer2 192.168.0.
Configuration du filtrage des IP à l'aide de RACADM Vous devez détenir le privilège de configuration pour effectuer ces étapes. Pour configurer le filtrage des IP, utilisez les objets RACADM suivants : • Avec la commande config : – cfgRacTuneIpRangeEnable – cfgRacTuneIpRangeAddr – cfgRacTuneIpRangeMask • Avec la commande set, utilisez les objets du groupe iDRAC.
Configuration des services Vous pouvez configurer et activer les services suivants sur iDRAC : • Configuration locale : désactiver l'accès à la configuration iDRAC (depuis le système hôte) à l'aide de l'interface locale RACADM et l'utilitaire de configuration iDRAC. • Serveur Web : activer l'accès à l'interface Web iDRAC. Si vous désactivez l'option, utilisez l'interface locale RACADM pour réactiver le Serveur Web, puisque la désactivation du Serveur Web désactive aussi l'interface distante RACADM.
– cfgOobSnmpAgentEnable – cfgOobSnmpAgentCommunity • Utilisez les objets dans les groupes de l'objet suivants à l'aide de la commande set : – iDRAC.LocalSecurity – iDRAC.LocalSecurity – iDRAC.SSH – iDRAC.Webserver – iDRAC.Telnet – iDRAC.Racadm – iDRAC.SNMP Pour plus d'informations sur ces objets, voir l' iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8), disponible à l'adresse dell.com/idracmanuals.
d'attente. Il est possible de configurer ces paramètres à l'aide de RACADM ou de l'interface Web de l'iDRAC. REMARQUE : La fonction VNC est sous licence et est disponible sous la licence iDRAC Enterprise. Vous pouvez choisir parmi plusieurs applications VNC ou clients bureau tels que ceux de RealVNC ou Dell Wyse PocketCloud. Une seule session de client VNC peut être active à la fois.
REMARQUE : La prise en charge du cryptage SSL n'est pas intégrée à la plupart des clients VNC. Pour configurer l'application de tunnel SSL : 1. Configurez le tunnel SSL pour qu'il accepte la connexion sur :. Par exemple, 127.0.0.1:5930. 2. Configurez le tunnel SSL pour qu'il se connecte à :. Par exemple, 192.168.0.120:5901. 3. Démarrez l'application de tunnel.
Définition des paramètres de l'écran LCD en utilisant l'interface Web Pour configurer l'écran LCD du panneau avant : 1. Dans l'interface Web d'iDRAC, accédez à Présentation → Matériel → Panneau avant. 2.
Configuration du paramétrage LED d'ID système Pour identifier un serveur, activez ou désactivez le clignotement du voyant d'identification du système sur le système géré. Définition des paramètres LED d'identification du système à l'aide de l'interface Web Pour configurer l'afficheur LED d'identification du système : 1. Dans l'interface Web d'iDRAC, accédez à Présentation → Matériel → Panneau avant. La page Panneau avant s'affiche. 2.
RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8) disponible à l'adresse dell.com/idracmanuals. Définition du premier périphérique de démarrage Vous pouvez définir le premier périphérique de démarrage ou du démarrage suivant uniquement ou pour tous les démarrages suivants. En fonction de cette sélection, vous pouvez définir le premier périphérique de démarrage du système.
Définition du premier périphérique de démarrage à l'aide de RACADM • Pour définir le premier périphérique de démarrage, utilisez l'objet cfgServerFirstBootDevice. • Pour activer un seul démarrage pour un périphérique, utilisez l'objet cfgServerBootOnce. Pour plus d'informations sur ces objets, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8), disponible à l'adresse dell.com/idracmanuals.
Activation ou désactivation de la connexion directe entre le SE et l'iDRAC Dans les serveurs dotés d'une carte réseau fille (NDC) ou de périphériques LOM ( LAN sur carte réseau), vous pouvez activer la fonction Connexion directe entre le SE et iDRAC qui fournit une communication haute vitesse bidirectionnelle intrabande entre l'iDRAC et le système d'exploitation hôte via un LOM partagé (serveurs en rack ou de type tour), une carte NIC dédiée (serveurs en rack, de type tour ou lame) ou la carte NIC USB.
Systèmes d'exploitation pris en charge pour la carte réseau USB Activation ou désactivation de la connexion directe à l'iDRAC à l'aide de l'interface Web Activation ou désactivation de la connexion directe entre le SE et iDRAC à l'aide de RACADM Activation ou désactivation de la connexion directe à l'iDRAC à l'aide de l'utilitaire de paramètres iDRAC Cartes prises en charge pour la connexion directe entre le système d'exploitation et l'iDRAC Le tableau suivant fournit une liste des cartes qui prennent en c
• RHEL 6.7 • vSphere v5.0 U2 ESXi • vSphere v5.1 U3 • vSphere v5.1 U1 ESXi • vSphere v5.5 ESXi • vSphere v5.5 U3 • vSphere 6.0 • VSphere 6.0 U1 • CentOS 6.5 • CentOS 7.0 • Ubuntu 14.04.1 LTS • Ubuntu 12.04.04 LTS • Debian 7.6 (Wheezy) • Debian 8.0 Sur les serveurs dotés de Windows 2008 SP2 64 bits, le périphérique USB CD virtuel iDRAC n'est pas détecté automatiquement (ou activé). Vous devez l'activer manuellement.
l'interface réseau correspondant au périphérique de carte réseau USB n'est pas active automatiquement. Vous pouvez effectuer l'une des opérations suivantes pour activer le périphérique de carte réseau USB : • Configurez l'interface de la carte réseau USB à l'aide de l'outil Network Manager. Naviguez vers Système → Administrateur → Réseau → Périphériques → Nouveau → Connexion Ethernet et sélectionnez Dell computer corp.Périphérique USB de carte réseau iDRAC virtuelle.
• LOM : le lien de transfert du SE à l'iDRAC entre l'iDRAC et le système d'exploitation hôte est établi via le périphérique LOM ou NDC. • USB : le lien de transfert du SE à l'iDRAC entre l'iDRAC et le système d'exploitation hôte est établi via le bus USB interne. Pour désactiver cette fonction sélectionnez Désactivée. 3. Si vous sélectionnez LOM en tant que configuration de transfert, et que le serveur est connecté à l'aide du mode dédié, saisissez l'adresse IPv4 du système d'exploitation.
REMARQUE : Si le serveur est connecté en mode LOM partagé, le champ Adresse IP du SE est désactivé. 4. Si vous choisissez Carte réseau USB comme configuration de connexion directe, entrez l'adresse IP de la carte réseau USB. La valeur par défaut est 169.254.0.1. Toutefois, si cette adresse IP entre en conflit avec une adresse IP d’autres interfaces du système hôte ou du réseau local, vous devez la modifier. Ne saisissez pas les adresses IP 169.254.0.3 et 169.254.0.4.
Type de connexion Type de certificat Mode d'obtention Les certificats SHA-2 sont également pris en charge. Concepts connexes Certificats de serveur SSL Génération d'une nouvelle demande de signature de certificat Certificats de serveur SSL iDRAC inclut un serveur Web configuré pour utiliser le protocole de sécurité standard SSL pour transférer des données cryptées dans un réseau.
Le certificat SSL de serveur Web de l'iDRAC prend en charge le caractère astérisque (*) comme une partie du composant le plus à gauche du nom commun lors de la génération d'une requête de signature de certificat (CSR). Par exemple,*.qa.com ou *.company.qa.com. Cela s'appelle un certificat générique.
Génération d'un fichier CSR à l'aide de l'interface RACADM Pour générer un CSR à l'aide de RACADM, utilisez les objets du groupe cfgRacSecurity avec la commande config ou utilisez les objets du groupe iDRAC.Security avec la commande set, puis utilisez la commande sslcsrgen pour générer le CSR. Pour en savoir plus, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8) disponible à l'adresse dell.com/idracmanuals.
4. Exécutez la commande racadm racreset pour réinitialiser l’iDRAC. Après la réinitialisation d’iDRAC, le nouveau certificat est appliqué. L’iDRAC devient indisponible pendant quelques minutes lors de la réinitialisation. REMARQUE : Vous devez réinitialiser l’iDRAC pour appliquer le nouveau certificat. Tant que l’iDRAC n'est pas réinitialisé, le certificat existant est actif. Affichage du certificat de serveur Vous pouvez afficher le certificat de serveur SSL actuel utilisé dans iDRAC.
REMARQUE : Vous devez réinitialiser l’iDRAC pour appliquer le nouveau certificat. Tant que l’iDRAC n'est pas réinitialisé, le certificat existant est actif. Téléversement d'un certificat de signature de certificat SSL personnalisé à l'aide de RACADM Pour téléverser le certificat de signature de certificat SSL personnalisé à l’aide de RACADM, utilisez la sous-commande sslcertupload, puis utilisez la commande racreset pour réinitialiser l’iDRAC.
Suppression d'un certificat de signature SSL personnalisé à l'aide de RACADM Pour supprimer le certificat de signature de certificat SSL personnalisé à l’aide de RACADM, utilisez la sous-commande sslcertdelete . Ensuite, utilisez la commande racreset pour réinitialiser l’iDRAC. Pour en savoir plus, voir le iDRAC RACADM Command Line Reference Guide (Guide de référence de la ligne de commande RACADM iDRAC disponible à l'adresse www.dell.com/esmmanuals.
4. Réinitialisez l'iDRAC cible en utilisant la commande racadm racreset Création d'un fichier de configuration iDRAC Le fichier de configuration .cfg peut être : • Créé • Obtenu depuis la commande racadm getconfig -f .cfg ou la commande racadm get -f .cfg • Obtenu depuis la commande racadm getconfig -f .cfg ou la commande racadm get -f .
PRÉCAUTION : Utilisez la sous-commande racresetcfg pour restaurer les paramètres par défaut de la base de données et de la NIC iDRAC, et pour supprimer tous les utilisateurs et configurations d'utilisateurs. Bien que l'utilisateur root soit disponible, d'autres paramètres utilisateur par défaut sont également restaurés. Règles d'analyse • Toutes les lignes qui commencent par '#' sont considérées correspondre à des commentaires. Une ligne de commentaire doit commencer dans la colonne 1.
Si vous tapez racadm getconfig -f < myexample >.cfg, la commande génère un fichier .cfg pour la configuration iDRAC actuelle. Ce fichier de configuration peut être utilisé comme exemple et comme modèle pour votre propre fichier . cfg. Modification de l'adresse IP d'iDRAC Lorsque vous modifiez l'adresse IP d'iDRAC dans le fichier de configuration, supprimez toutes les entrées =value inutiles.
Désactivation de l'accès pour modifier les paramètres de configuration iDRAC sur un système hôte Vous pouvez désactiver l'accès pour modifier les paramètres de configuration iDRAC via l'interface locale RACADM ou l'utilitaire de configuration d'iDRAC. Cependant, vous pouvez afficher ces paramètres de configuration. Pour ce faire : 1. Dans l'interface Web d'iDRAC, accédez à Présentation → Paramètres iDRAC → Réseau → Services. 2.
Affichage des informations d'iDRAC et d'un système géré 5 Vous pouvez afficher l'intégrité et les propriétés d'iDRAC et d'un système géré, l'inventaire matériel et logiciel, l'intégrité des capteurs, les périphériques de stockage, les périphériques réseau et afficher les sessions utilisateur et y mettre fin. Pour les serveurs lames, vous pouvez également afficher les informations FlexAddress.
Affichage de l'inventaire du système Vous pouvez afficher des informations sur les composants matériels et logiciels installés sur le système géré. Pour ce faire, dans l'interface Web d'iDRAC, accédez à Présentation → Serveur → Propriétés → Inventaire du système. Pour des informations sur les propriétés affichées, voir l'aide en ligne d'iDRAC.
système au redémarrage) pour collecter l'inventaire du système lors du redémarrage. Au bout de quelques minutes, ouvrez une session dans l'iDRAC et accédez à la page de Inventaire du système pour afficher les détails. Il se peut que les informations soient disponibles au bout de cinq minutes en fonction du matériel installé sur le serveur. REMARQUE : L'option CSIOR est activée par défaut.
REMARQUE : Sur les serveurs Dell PowerEdge de 13e génération, l’opération de reconstruction IDSDM est effectuée en arrière-plan et le système n’est pas interrompu pendant le processus de reconstruction. Vous pouvez vérifier les journaux Lifecycle Controller pour afficher l’état de l’opération de reconstruction. Sur un serveur Dell PowerEdge de 12e génération, le système est arrêté pendant que l’opération de reconstruction est effectuée.
Affichage des informations des capteurs Utilisation de l'interface Web Température Présentation → Serveur → Alimentation/Thermique → Températures Tension Présentation → Serveur → Alimentation/Thermique → Tensions Utilisation de l'interface RACADM Surveillance de l'indice de performances de l’UC, de la mémoire et des modules d’E/S Dans les serveurs Dell PowerEdge de 13e génération, l’option Intel ME offre la prise en charge de la fonction CUPS (Compute Usage Per Second, Calcul d'utilisation par second
compteurs sont alors agrégés pour mesurer le trafic PCI Express de tous les segments PCI Express provenant du progiciel. Il s’agit de la mesure de l’utilisation de la bande passante des E/S du système. • Indice de CUPS au niveau système : l'indice de CUPS est calculé en regroupant l'indice d’UC, de la mémoire et des E/S, prenant en compte un facteur de charge prédéfini de chaque ressource système. Le facteur de charge dépend de la nature de la charge de travail exécutée sur le système.
Pour plus d'informations sur les propriétés affichées, voir l'aide en ligne d'iDRAC. Surveillance de l'indice de performances de l’UC, de la mémoire et des modules d’E/S à l’aide de RACADM Utilisez la sous-commande SystemPerfStatistics pour surveiller l'indice de performances de l'UC, de la mémoire et des modules d’E/S. Pour en savoir plus, voir le iDRAC RACADM Command Line Reference Guide (Guide de référence de ligne de commande RACADM iDRAC) disponible à l'adresse dell.com/ esmmanuals.
Les données collectées sont représentées sous forme graphique pour suivre les niveaux de 10 % et 1 %. Les données de température enregistrées ne peuvent être effacées qu'avant l'expédition de l'usine. Un événement est généré si le système continue de fonctionner au-dessus du seuil de température normalement toléré durant une durée de fonctionnement spécifiée.
Configuration du seuil d’avertissement de température d’entrée à l’aide de l’interface Web Pour configurer le seuil d’avertissement de la température d’entrée : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → Alimentation / Thermique → Températures. 2. Dans la section Capteurs de température, pour la Température d’entrée de la carte système, entrez les valeurs minimale et maximale du Seuil d’avertissement en degrés Celsius ou Fahrenheit.
La page Interfaces réseau affiche toutes les interfaces réseau disponibles sur le système d’exploitation hôte. 2. Pour afficher la liste des interfaces réseau associées à un périphérique réseau, à partir du menu déroulant FQDD de périphérique réseau, sélectionnez un périphérique réseau, puis cliquez sur Appliquer. Les détails de l'adresse IP du SE sont affichés dans la section Interfaces réseau du SE hôte. 3. Dans la colonne FQDD de périphérique, cliquez sur le lien du périphérique réseau.
stockée dans la mémoire non volatile CMC et elle est envoyée à iDRAC pendant son démarrage ou lorsque CMC FlexAddress est activé. Si CMC permet d'utiliser des adresses MAC affectées par le châssis, iDRAC affiche l'adresse MAC dans les pages suivantes : • Présentation → Serveur → Propriétés Détails → Informations iDRAC. • Présentation → Serveur → Propriétés WWN/MAC. • Présentation générale → Paramètres iDRAC → Propriétés Informations iDRAC → Paramètres réseau actuels.
Configuration de la communication iDRAC 6 Vous pouvez communiquer avec iDRAC en utilisant les modes suivants : • Interface Web iDRAC • Connexion série en utilisant un câble DB9 (RAC série ou IPMI sériel). S'applique aux serveurs en rack et de type tour uniquement.
Mode de communication Protocole pris en charge Commandes prises en charge Conditions requises Interface RACADM distante HTTPS Interface RACADM distante L'interface distance RACADM est installée et activée. Micrologiciel RACADM SSH Micrologiciel RACADM Le micrologiciel RACADM est installé et activé. Telnet Interface RACADM locale IPMI Interface RACADM locale L'interface RACADM locale est installée.
• Linux Minicom dans un Xterm • HyperTerminal Private Edition (version 6.3) de Hilgraeve Selon le point en cours du processus de démarrage du système géré, vous pouvez voir l'écran du POST ou celui du système d'exploitation. Ceci dépend de la configuration : SAC pour Windows et des écrans du mode texte Linux pour Linux. 4. Activez les connexions RAC série ou IPMI série dans iDRAC.
Activation des modes de base et terminal de connexion série IPMI Pour activer l'acheminement série IPMI du BIOS vers iDRAC, configurez IPMI série dans les modes suivants dans iDRAC : REMARQUE : Ces informations s'appliquent uniquement à iDRAC sur des serveurs en rack et de type tour. • Mode de base IPMI — Prend en charge une interface binaire pour l'accès au programme, telle que IPMI shell (ipmish) qui est inclus dans BMU (Baseboard Management Utility).
2. • Avec la commande config : racadm config -g cfgSerial -o cfgSerialConsoleEnable 0 • Avec la commande set : racadm set iDRAC.Serial.Enable 0 Configurez le débit en bauds des communications IPMI série : • Avec la commande config : racadm config -g cfgIpmiSerial -o cfgIpmiSerialBaudRate • Avec la commande set : racadm set iDRAC.IPMISerial.BaudRate où est égal à 9 600, 19 200, 57 600 ou 115 200 b/s. 3. 4.
6. Vérifiez que le connecteur MUX (connecteur série externe) est correctement défini sur le périphérique d'accès à distance dans le programme de configuration du BIOS pour configurer le BIOS pour la connexion série.
Pour définir le mode de communication SOL : 1. Configurez le BIOS pour une connexion série. 2. Configurez iDRAC pour utiliser SOL. 3. Activez un protocole pris en charge (SSH, Telnet, IPMItool).
L'écran Communications série sur le LAN apparaît. 2. Activez SOL, définissez les valeurs et cliquez sur Appliquer. Les paramètres SOL IPMI sont définis. 3. Pour définir la fréquence d'accumulation de caractères et le seuil d'envoi de caractères, sélectionnez Paramètres avancés. L'écran Paramètres avancés Communication série sur LAN s'affiche. 4. Définissez les valeurs des attributs et cliquez sur Appliquer. Les paramètres avancés SOL IPMI sont définis. Ces valeurs améliorent les performances.
Activation d'un protocole pris en charge à l'aide de l'interface Web Pour activer SSH ou Telnet, accédez à Présentation générale → Paramètres iDRAC → Réseau → Services et sélectionnez Activé pour SSH ou Telnet. Pour activer IPMI, accédez à Présentation → Paramètres iDRAC → Réseau et sélectionnez Activer IPMI sur le LAN. Vérifiez que la valeur Clé de cryptage correspond à des zéros ou appuyez sur la touche Retour arrière pour remplacer la valeur par des caractères NULL.
REMARQUE : Si nécessaire, vous pouvez changer le délai d'attente SOL par défaut dans Présentation → Paramètres iDRAC → Réseau → Services. 1. Installez IPMITool depuis le DVD Dell Systems Management Tools and Documentation. Pour les instructions d'installation, voir le Guide d'installation rapide du logiciel. 2.
REMARQUE : Si nécessaire, vous pouvez changer le délai d'attente SSH ou Telnet par défaut dans Présentation générale → Paramètres iDRAC → Réseau → Services. 1. Exécutez la commande suivante pour vous connecter à iDRAC: putty.exe [-ssh | -telnet] @ REMARQUE : Le numéro de port est facultatif. Il est nécessaire uniquement lorsque le numéro de port est réaffecté. 2. Exécutez la commande console com2 ou connect pour démarrer SOL et le système géré.
La commande console -h com2 affiche le contenu du tampon de l'historique série avant d'attendre une entrée à partir du clavier ou de nouveaux caractères du port série. La taille par défaut (et maximale) du tampon de l'historique est de 8 192 caractères. Vous pouvez définir une plus petite valeur en utilisant la commande suivante : racadm config -g cfgSerial -o cfgSerialHistorySize 4. Quittez la session SOL pour fermer une session SOL active.
• Pour quitter la redirection SOL, appuyez sur , <Échap>, puis sur . La session SOL se ferme. • Pour quitter une session SOL depis Telnet sur Linux, appuyez sur +] et maintenez les touches enfoncées. Une invite Telnet s'affiche. Entrez quit pour quitter Telnet. • Si une session SOL n'est pas terminée complètement dans l'utilitaire, d'autres sessions SOL peuvent ne pas être disponibles.
• Avec la commande set : racadm set iDRAC.IPMILan.PrivLimit où correspond à l'une des valeurs suivantes : 2 (Utilisateur), 3 (Opérateur) ou 4 (Administrateur) 3. Définissez la clé de cryptage du canal LAN IPMI, si nécessaire : • Avec la commande config : racadm config -g cfgIpmiLan -o cfgIpmiEncryptionKey • Avec la commande set : racadm set iDRAC.IPMILan.EncryptionKey où est une clé de cryptage de 20 caractères au format hexadécimal valide.
Désactivation de l'interface locale RACADM Par défaut, l'interface locale RACADM est activée. Pour la désactiver, voir Désactivation de l'accès pour modifier les paramètres de configuration d'iDRAC sur le système hôte. Activation d'IPMI sur un système géré Sur un système géré, utilisez Dell Open Manage Server Administrator pour activer ou désactiver IPMI.
Activation de l'ouverture de session dans la console virtuelle après le démarrage Dans le fichier /etc/inittab, ajoutez une nouvelle ligne pour configurer agetty sur le port série COM2 : co:2345:respawn:/sbin/agetty -h -L 57600 ttyS1 ansi L'exemple suivant montre un fichier avec la nouvelle ligne. #inittab This file describes how the INIT process should set up #the system in a certain run-level. #Author:Miquel van Smoorenburg #Modified for RHS Linux by Marc Ewing and Donnie Barnes #Default runlevel.
Tableau 12.
Génération de clés publiques pour Windows Pour utiliser l'application PuTTY Key Generator pour créer la clé de base : 1. Démarrez l'application et sélectionnez SSH-2 RSA ou SSH-2 DSA comme type de clé à générer (SSH-1 n'est pas pris en charge). Les algorithmes de génération de clé compatibles sont RSA et DSA uniquement. 2. Entrez le nombre de bits de la clé. Pour RSA, il doit être compris entre 768 et 4 096 bits et pour DSA, il doit être de 1 024 bits. 3.
La page Utilisateurs s'affiche. 2. Dans la colonne Réf. utilisateur, cliquez sur un numéro de référence utilisateur. La page Menu principal utilisateur s'affiche. 3. Sous Configurations de clés SSH, sélectionnez Téléverser une ou des clés SSH, puis cliquez sur Suivant. La page Téléverser une ou des clés SSH s'affiche. 4. Téléversez les clés SSH de l'une des manières suivantes : • Téléversez le fichier de clé. • Copiez le contenu du fichier de clé dans zone de texte.
Suppression des clés SSH Avant de supprimer des clés publiques, affichez les clés si elles sont définies afin de ne pas les supprimer par inadvertance. Suppression de clés SSH à l'aide de l'interface Web Pour supprimer des clés SSH : 1. Dans l'interface Web, accédez à Overview → iDRAC Settings → Network → User Authentication → Local Users(Présentation, Paramètres iDRAC, Réseau, Authentification des utilisateurs, Utilisateurs locaux). La page Utilisateurs s'affiche. 2. Dans la colonne Réf.
Configuration des comptes et des privilèges des utilisateurs 7 Vous pouvez configurer des comptes d'utilisateur avec des privilèges spécifiques (droit basé sur un rôle) pour gérer le système à l'aide d'iDRAC et maintenir la sécurité du système. Par défaut, iDRAC est configuré avec un compte d'administrateur local. Ce nom par défaut est racine et le mot de passe est calvin. En tant qu'administrateur, vous pouvez configurer des comptes d'utilisateur pour autoriser d'autres utilisateurs à accéder à iDRAC.
REMARQUE : L'utilisateur 1 est réservé à l'utilisateur anonyme IPMI ; vous ne pouvez pas changer cette configuration. La page Menu principal utilisateur s'affiche. 3. Sélectionnez Configurer, puis cliquez sur Suivant. La page Configuration de l'utilisateur s'affiche. 4. Activez l'ID utilisateur et spécifiez le nom d'utilisateur, le mot de passe et les droits d'accès de l'utilisateur. Vous pouvez également activer l'authentification SNMPv3 pour cet utilisateur.
• Si vous avez utilisé la commande get : iDRAC.Users.UserName= Si l'objet cfgUserAdminUserName n'a pas de valeur, le numéro d'index, indiqué par l'objet cfgUserAdminIndex, peut être utilisé. Si un nom est affiché après « = », cet index est pris par ce nom d'utilisateur. Lorsque vous activez ou désactivez manuellement un utilisateur avec la sous-commande racadm config, vous devez spécifier l'index avec l'option -i.
Pour vérifier, utilisez l'une des commandes suivantes : racadm getconfig -u jean racadm getconfig –g cfgUserAdmin –i 3 Pour plus d'informations sur les commandes RACADM, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8), disponible à l'adresse dell.com/idracmanuals.
Tableau 13.
Génération en cours Génération antérieure Description Debug (Débogage) Exécuter des commandes de diagnostic Permet à l'utilisateur d'exécuter des commandes de diagnostic.
3. Cliquez sur Suivant et sélectionnez Contrôleur de domaine. 4. Cliquez sur Suivant et sur Terminer. Le certificat SSL est installé. Exportation d'un certificat CA racine de contrôleur de domaine vers l'iDRAC REMARQUE : Si votre système fonctionne sous Windows 2000 ou que vous utilisez une autorité de certification autonome, les étapes suivantes peuvent être différentes. Pour exporter le certificat CA racine du contrôleur de domaine vers iDRAC : 1.
4. Cliquez sur Suivant et accédez au fichier de certificat SSL. 5. Installez le certificat SSL d'iDRAC dans l'Autorité de certification racine de confiance de chaque contrôleur de domaine. Si vous avez installé votre propre certificat, vérifiez que l'autorité de certification signataire du certificat se trouve dans la liste des autorités de certification racines de confiance. Si elle n'y figure pas, vous devez l'installer sur tous les contrôleurs de domaine. 6.
configurer jusqu'à cinq groupes de rôles dans chaque iDRAC. Le tableau répertorie les privilèges par défaut des groupes de rôles. Tableau 15.
Configuration d'Active Directory avec le schéma standard Pour configurer l'iDRAC pour l'accès à une connexion Active Directory : 1. Sur un serveur Active Directory (contrôleur de domaine), ouvrez le snap-in Utilisateurs et ordinateurs Active Directory. 2. Créez un groupe ou sélectionnez un groupe existant. Ajoutez l'utilisateur Active Directory comme membre du groupe Active Directory pour accéder à iDRAC. 3.
Les paramètres sont appliqués et la page Configuration et gestion d'Active Directory - Étape 4a sur 4 s'affiche. 12. Cliquez sur Terminer. Les paramètres Active Directory pour le schéma standard sont définis. Configuration d'Active Directory avec le schéma standard à l'aide de RACADM Pour configurer iDRAC Active Directory avec le schéma standard à l'aide de l'interface RACADM : 1.
Le serveur de catalogue global est uniquement nécessaire pour le schéma standard lorsque les comptes d'utilisateur et les groupes de rôles se trouvent dans des domaines différents. S'il existe plusieurs domaines, seul le groupe Universel peut être utilisé. Le nom de domaine complet qualifié ou l'adresse IP que vous spécifiez dans ce champ doit correspondre au champ Objet ou Autre nom de l'objet de votre certificat de contrôleur de domaine si la validation de certificat est activée.
• Avec la commande config : racadm config -g cfgUserDomain -o cfgUserDomainName -i • Avec la commande set : racadm set iDRAC.UserDomain..Name Vous pouvez configurer jusqu'à 40 domaines d'utilisateur avec des numéros d'index compris entre 1 et 40.
L'objet Périphérique iDRAC est le lien au micrologiciel iDRAC pour interroger Active Directory pour l'authentification et l'autorisation. Lorsqu'iDRAC est ajouté au réseau, l'administrateur doit configurer iDRAC et son objet Périphérique avec son nom Active Directory pour que les utilisateurs puissent exécuter l'authentification et l'autorisation avec Active Directory. En outre, l'administrateur doit ajouter iDRAC à au moins un objet Association pour que les utilisateurs puissent s'authentifier.
L'illustration suivante montre un exemple d'accumulation de privilèges à l'aide du schéma étendu. Figure 3. Accumulation de privilèges pour un utilisateur L'illustration montre deux objets Association, A01 et A02. L'utilisateur 1 est associé à iDRAC2 via les deux objets associés.
Extension du schéma Active Directory L'extension du schéma Active Directory ajoute une unité organisationnelle Dell, des classes et des attributs de schéma, des exemples de privilèges et des objets Association au schéma Active Directory. Avant d'étendre le schéma, vérifiez que vous disposez des privilèges d'administration de schéma dans le rôle de propriétaire FSMO (Flexible Single Master Operation) du contrôleur de domaine principal dans la forêt de domaines.
Classes et attributs Tableau 16. Définitions de classe pour les classes ajoutées au schéma Active Directory Nom de classe Numéro d'identification d'objet (OID) attribué delliDRACDevice 1.2.840.113556.1.8000.1280.1.7.1.1 delliDRACAssociation 1.2.840.113556.1.8000.1280.1.7.1.2 dellRAC4Privileges 1.2.840.113556.1.8000.1280.1.1.1.3 dellPrivileges 1.2.840.113556.1.8000.1280.1.1.1.4 dellProduct 1.2.840.113556.1.8000.1280.1.1.1.5 Tableau 17. DelliDRACdevice class OID 1.2.840.113556.1.8000.1280.1.7.
Tableau 19. dellRAC4Privileges Class OID 1.2.840.113556.1.8000.1280.1.1.1.3 Description Définit les privilèges (droits d'autorisation) d'iDRAC Type de classe Classe auxiliaire SuperClasses Aucun Attributs dellIsLoginUser dellIsCardConfigAdmin dellIsUserConfigAdmin dellIsLogClearAdmin dellIsServerResetUser dellIsConsoleRedirectUser dellIsVirtualMediaUser dellIsTestAlertUser dellIsDebugCommandAdmin Tableau 20. dellPrivileges class OID 1.2.840.113556.1.8000.1280.1.1.1.
Tableau 22. Liste des attributs ajoutés au schéma Active Directory Nom/Description de l'attribut OID attribué/Identifiant d'objet de syntaxe Valeur unique dellPrivilegeMember 1.2.840.113556.1.8000.1280.1.1.2.1 FALSE Liste des objets dellPrivilege qui appartiennent à cet attribut. Nom distingué (LDAPTYPE_DN 1.3.6.1.4.1.1466.115.121.1.12) dellProductMembers 1.2.840.113556.1.8000.1280.1.1.2.2 FALSE Liste des objets dellRacDevice et DelliDRACDevice qui appartiennent à ce rôle.
Nom/Description de l'attribut OID attribué/Identifiant d'objet de syntaxe dellIsVirtualMediaUser 1.2.840.113556.1.8000.1280.1.1.2.9 TRUE TRUE si l'utilisateur a les droits Média Virtuel sur le périphérique. Booléen (LDAPTYPE_BOOLEAN 1.3.6.1.4.1.1466.115.121.1.7) dellIsTestAlertUser 1.2.840.113556.1.8000.1280.1.1.2.1 TRUE 0 TRUE si l'utilisateur a les droits Utilisateur pour l'alerte test sur le périphérique. dellIsDebugCommandAdmin Valeur unique Booléen (LDAPTYPE_BOOLEAN 1.3.6.1.4.1.1466.115.121.
et ordinateurs Active Directory pendant l'installation. Consultez le guide d'installation rapide de Dell OpenManage pour plus d'instructions sur l'installation du logiciel de gestion de systèmes. Pour les systèmes d'exploitation Windows 64 bits, le propramme d'installation du snap-in se trouve sous : :\SYSMGMT\ManagementStation\support\OMActiveDirectory_SnapIn64 Pour des informations supplémentaires sur le snap-in Utilisateurs et ordinateurs Active Directory, consultez la documentation Microsof
6. Cliquez sur l'onglet Privilèges de gestion à distance pour l'utilisateur ou le groupe. Création d'un objet Association Pour créer un objet Association : REMARQUE : L'objet Association iDRAC provient d'un groupe et son étendue est définie sur Domaine local. 1. Dans la fenêtre Racine de la console (MMC), cliquez avec le bouton droit de la souris sur un conteneur. 2. Sélectionnez Nouveau → Dell Remote Management Object Advanced. 3. Entrez le nom du nouvel objet et sélectionnez Objet Association. 4.
Cliquez sur l'onglet Objet Privilège pour ajouter l'objet Privilège à l'association qui définit les privilèges de l'utilisateur ou du groupe d'utilisateurs lors de l'authentification sur un périphérique iDRAC. Un seul objet Privilège peut être ajouté à un objet Association. 1. Sélectionnez l'onglet Objet Privilège et cliquez sur Ajouter. 2. Entrez le nom de l'objet Privilège et cliquez sur OK. 3.
Les paramètres Active Directory du mode Schéma étendu sont configurés. Configuration d'Active Directory avec le schéma étendu à l'aide de l'interface RACADM Pour configurer Active Directory avec le schéma étendu en utilisant l'interface RACADM : 1.
L'utilisation de la commanRACADM suivante peut être facultative : racadm sslcertdownload -t 0x1 -f 2. 3. 4. Si DHCP est activé sur iDRAC et que vous voulez utiliser le nom DNS fourni par le serveur DHCP, entrez la commande RACADM suivante : • Avec la commande config : racadm config -g cfgLanNetworking -o cfgDNSServersFromDHCP 1 • Avec la commande set : racadm set iDRAC.IPv4.
REMARQUE : Lorsque vous testez les paramètres Active Directory avec la validation de certificat activée, iDRAC impose que le serveur Active Directory soit identifié par le nom de domaine complet qualifié (FQDN) et non pas par une adresse IP. S'il est identifié par une adresse IP, la validation de certificat échoue, car iDRAC ne peut pas communiquer avec le serveur Active Directory.
REMARQUE : Si la validation de certificat est activée, définissez le nom de domaine complet qualifié du serveur LDAP et vérifiez qu'il est correctement défini sous Présentation générale → Paramètres iDRAC → Réseau. REMARQUE : Dans cette version, les groupes imbriqués ne sont pas pris en charge. Le micrologiciel recherche le membre direct du groupe pour le faire correspondre au nom de domaine d'utilisateur. En outre, un seul domaine est pris en charge. Les domaines croisés ne sont pas pris en charge. 6.
REMARQUE : Lors du test des paramètres LDAP avec l'option d'activation de la validation des certificats activée, iDRAC nécessite que le serveur LDAP soit identifié par le nom de domaine complet qualifié (FQDN) et non pas par une adresse IP. Si le serveur est identifié par une adresse IP, la validation de certificat échoue, car iDRAC ne peut pas communiquer avec le serveur LDAP. REMARQUE : Lorsque LDAP générique est activé, iDRAC tente d'abord de connecter l'utilisateur comme utilisateur de répertoire.
Configuration de l'iDRAC pour la connexion directe ou par carte à puce 8 Cette section fournit des informations sur la configuration d'iDRAC pour la connexion à l'aide d'une carte à puce (pour les utilisateurs locaux et Active Directory) et pour la connexion directe (SSO) (pour les utilisateurs Active Directory.) La connexion directe et la connexion avec une carte à puce sont des fonctions disponibles sous licence.
Tâches connexes Enregistrement d'iDRAC en tant qu'ordinateur dans un domaine racine Active Directory Génération d'un fichier Keytab Kerberos Création d'objets Active Directory et fourniture de privilèges Enregistrement d'iDRAC en tant qu'ordinateur dans un domaine racine Active Directory Pour enregistrer iDRAC dans un domaine racine Active Directory : 1. Cliquez sur Présentation générale → Paramètres iDRAC → Réseau → Réseau. La page Réseau s'affiche. 2.
Le type de cryptage est AES256-SHA1. Le type de principal est KRB5_NT_PRINCIPAL. La propriété Utiliser les types de cryptage AES 256 pour ce compte doit être activée dans les propriétés du compte d'utilisateur auquel le nom de principal de service est adressé. REMARQUE : Utilisez des minuscules pour le Nom iDRAC et le Nom principal de service. Utilisez des majuscules pour le nom de domaine, comme indiqué dans l'exemple. 3. Exécutez la commande suivante : C:\>setspn -a HTTP/iDRACname.domainname.
Configuration de Firefox pour activer la connexion directe (SSO) Active Directory Pour configurer les paramètres du navigateur pour Firefox : 1. Dans la barre d'adresses, entrez about:config. 2. Dans Filtre, entrez network.negotiate. 3. Ajoutez le nom de domaine à network.negotiate-auth.trusted-uris (en utilisant une liste d'éléments séparés par des virgules). 4. Ajoutez le nom de domaine à network.negotiate-auth.trusted-uris (en utilisant une liste d'éléments séparés par des virgules).
• Utilisation de la commande config : racadm config -g cfgActiveDirectory -o cfgADSSOEnable 1 • Avec la commande set : racadm set iDRAC.ActiveDirectory.SSOEnable 1 Configuration d'ouverture de session iDRAC par carte à puce pour les utilisateurs locaux Pour configurer un utilisateur local iDRAC pour la connexion par carte à puce : 1. Téléchargez le certificat d'utilisateur de carte à puce et le certificat CA autorisé vers l'iDRAC. 2.
Téléversement d'un certificat d'autorité de certification pour une carte à puce Avant de téléverser le certificat d'autorité de certification, vérifiez que vous disposez d'un certificat autosigné d'autorité de certification. Concepts connexes Obtention de certificats Téléversement d'un certificat d'autorité de certification de confiance pour une carte à puce à l'aide de l'interface Web Pour téléverser un certificat d'autorité de certification de confiance pour une connexion avec une carte à puce : 1.
Obtention de certificats Génération d'un fichier Keytab Kerberos Configuration d'Active Directory avec le schéma standard à l'aide de l'interface Web d'iDRAC Configuration d'Active Directory avec le schéma standard à l'aide de RACADM Configuration d'Active Directory avec le schéma étendu à l'aide de l'interface Web iDRAC Configuration d'Active Directory avec le schéma étendu à l'aide de l'interface RACADM Activation ou désactivation de l'ouverture de session par carte à puce Avant d'activer ou désactiver l
Pour en savoir plus, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l’interface de ligne de commande RACADM iDRAC8), disponible à l’adresse dell.com/ idracmanuals. Activation ou désactivation de l'ouverture de session par carte à puce à l'aide de l'utilitaire de configuration d'iDRAC Pour activer ou désactiver la fonction d'ouverture de session par carte à puce : 1. Dans l'utilitaire de configuration d'iDRAC, accédez à Carte à puce.
9 Configuration d'iDRAC pour envoyer des alertes Vous pouvez définir des alertes et des actions pour certains événements qui se produisent sur le système géré. Un événement se produit lorsque l'état d'un composant du système est supérieur à l'état prédéfini.
Activation ou désactivation des alertes à l'aide de l'interface Web Pour activer ou désactiver la génération d'alertes : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → Alertes. La page Alertes s'affiche. 2. Dans la section Alertes : 3. • Sélectionnez Désactiver pour désactiver la génération d'alerte ou une action d'événement. Cliquez sur Appliquer pour enregistrer le paramètre. • Sélectionnez Activer pour activer la génération d'alertes ou exécuter une action d'événement.
REMARQUE : Même si vous disposez de privilèges d'écriture uniquement, vous pouvez filtrer les alertes. 1. Dans l'interface Web d'iDRAC, accédez à Présentation → Serveur → Alertes. La page Alertes s'affiche. 2. Dans la section Filtre d'alertes sélectionnez une ou plusieurs des catégories suivantes : • 3. 4.
4. • Alerte par e-mail • Interruption SNMP • Alerte IPMI • Journal système distant • Journal du SE • Événements WS Cliquez sur Appliquer. Le paramétrage est enregistré. 5. Dans la section Alertes, sélectionnez Activer pour envoyer des alertes aux destinations définies. 6. Facultativement, vous pouvez envoyer un événement test. Dans le champ ID de message pour tester l'événement, saisissez l'ID de message pour tester si l'alerte est générée, puis cliquez sur Tester.
Définition d'actions d'événement Vous pouvez définir des actions d'événement, telles qu'un redémarrage, un cycle d'alimentation, une mise hors tension, ou n'exécuter aucune action sur le système. Concepts connexes Filtrage des alertes Activation ou désactivation des alertes Définition d'actions d'événement à l'aide de l'interface Web Pour configurer une action : 1. Dans l'interface Web d'iDRAC, accédez à Présentation → Serveur → Alertes. La page Alertes s'affiche. 2.
• Vous disposez de l'autorisation de configuration RAC. • Vous avez défini des filtres d'événements. Concepts connexes Configuration des destinations d'alerte IP Configuration des paramètres d'alerte par e-mail Configuration des destinations d'alerte IP Vous pouvez configurer des adresses IPv6 ou IPv4 pour recevoir les alertes IPMI ou les interruptions SNMP.
• Pour une adresse IPv6 : racadm config -g cfgIpmiPetIpv6 -o cfgIpmiPetIpv6AlertEnable -i (index) (0|1) , où (index) est l'index de destination et 0 ou 1 désactive ou active l'interruption. Par exemple, pour activer l'interruption avec l'index 4, entrez la commande suivante : racadm config -g cfgIpmiPet -o cfgIpmiPetAlertEnable -i 4 1 2.
Configuration des paramètres d'alerte par e-mail Vous pouvez configurer l'adresse e-mail destinataire des alertes par e-mail. Configurez également les paramètres d'adresse du serveur SMTP. REMARQUE : Si vous utilisez le serveur de messagerie Microsoft Exchange Server 2007, veillez à ce que le nom de domaine d'iDRAC soit configuré pour que le serveur de messagerie puisse recevoir les alertes par e-mail d'iDRAC. REMARQUE : Les alertes par e-mail prennent en charge les adresses iPv4 et IPv6.
3. où 1 est l'index de destination de l'e-mail et [email-address] est l'adresse e-mail de destination qui reçoit les alertes d'événements de la plate-forme. Pour configurer un message personnalisé : • Avec la commande config : racadm config -g cfgEmailAlert -o cfgEmailAlertCustomMsg -i [index] [message personnalisé] où [index] est l'index de destination de l'e-mail et [custom-message], le message personnalisé. • 4. Avec la commande set : racadm set iDRAC.EmailAlert.CustomMsg.
Configuration des événements WS Le protocole des événements WS est utilisé pour un service client (abonné) pour enregistrer l'intérêt (abonnement) sur un serveur (source d'événement) pour recevoir les messages contenant les événements de serveur (notifications ou messages d'événement). Les clients souhaitant recevoir des messages d'événement WS peuvent s'inscrire à iDRAC et recevoir des événements de tâche du Lifecycle Controller.
REMARQUE : Cette section s’affiche uniquement pour des châssis PowerEdge FX2/FX2s et si le mode de Gestion du châssis basé sur le serveur est défini sur Écran ou Gérer et surveiller dans le CMC. 1. Sur l’interface CMC, cliquez sur Présentation du châssis → Configuration → Généralités. 2. Depuis le menu déroulant Gestion du châssis en mode serveur, sélectionnez Gérer et surveiller, puis cliquez sur Appliquer. 3. Lancement de l’interface Web iDRAC, cliquez sur Présentation → Paramètres iDRAC → CMC. 4.
ID du message Description DIS Découverte automatique ENC Enceinte stockage FAN Événement ventilateur FSD Debug (Débogage) HWC Configuration matérielle IPA Changement d'adresse IP DRAC ITR Intrusion JCP Contrôle des tâches LC Lifecycle Contr LIC Licences LNK Condition de la liaison LOG Événement journal MEM Mémoire NDR Pilote SE NIC Carte réseau Configuration NIC OSD Déploiement du SE OSE Événement OS PCI Périphérique PCI PDR Disque physique PR Changement composant P
ID du message Description RDU Redondance RED Téléchargement FW RFL Média IDSDM RFLA IDSDM Absent RFM SD FlexAddress RRDU Redondance IDSDM RSI Service à distance SEC Événement sécurité Journal d'évènements système Journal des événements système SRD RAID logiciel SSD SSD PCIe STOR Stockage SUP Tâche de mise à jour FW SWC Configuration logicielle SWU Changement logiciel SYS Infos système TMP Température TST Alerte test UEFI Événement UEFI USR Suivi utilisateur VDR Dis
ID du message Description VME Média virtuel VRM Console virtuelle WRK Note de travail 204
Gestion des journaux 10 iDRAC fournit un journal Lifecycle qui contient les événements liés au système, aux périphériques de stockage, aux périphériques de réseau, aux mises à jour de micrologiciel, aux modifications de configuration, aux messages de licence, etc. Cependant, les événements du système sont également disponibles comme journal distinct appelé SEL (System Event Log). Le journal Lifecycle est accessible via l'interface Web iDRAC, l'interface RACADM et l'interface WS-MAN.
Une fois que le journal SEL est effacé, une entrée est consignée dans le journal du Lifecycle Controller. L'entrée de journal inclut le nom d'utilisateur et l'adresse IP de l'emplacement où le journal SEL a été effacé. Affichage du journal des événements système à l'aide de l'interface RACADM Pour afficher le journal SEL : racadm getsel Si aucun argument n'est spécifié, le journal est affiché dans son intégralité.
• SSH • Interface Web • RACADM • SM-CLP • IPMI sur le LAN • Série • Console virtuelle • Média virtuel Vous pouvez filtrer les journaux en fonction de la catégorie et du niveau gravité et afficher, exporter et ajouter une note de travail à un événement de journal.
Exportation des journaux du Lifecycle Controller Vous pouvez exporter le journal du Lifecycle Controller entier (entrées actives et archivées) dans un seul fichier compressé XML sur un partage réseau ou sur le système local. L'extension de fichier XML compacté est .xml.gz. Les entrées de fichier sont commandées de façon séquentielle en fonction de leurs numéros de séquence, commandées à partir du numéro de séquence le plus bas jusqu'au plus élevé.
Configuration de la journalisation d'un système distant Vous pouvez envoyer des journaux Lifecycle à un système distant. Auparavant, vérifiez que : • Il existe une connectivité réseau entre iDRAC et le système distant. • Le système distant et iDRAC se trouvent dans le même réseau. Configuration de la journalisation d'un système distant à l'aide de l'interface Web Pour configurer les paramètres d'un serveur syslog distant : 1.
11 Surveillance et gestion de l'alimentation Vous pouvez utiliser iDRAC pour surveiller et gérer l'alimentation du système géré afin de protéger le système contre les surtensions en distribuant et en régulant de manière appropriée la consommation d'alimentation du système. Les principales fonctions sont les suivantes : • Surveillance de l'alimentation : affichage de l'état de l'alimentation, historique des mesures d'alimentation, moyennes de courant, pics, etc. associés au système géré.
Surveillance de l'alimentation à l'aide de l'interface Web Pour afficher les informations de surveillance de l'alimentation, dans l'interface Web iDRAC, accédez à Présentation → Serveur → Alimentation/Thermique → Surveillance de l'alimentation. La page Surveillance de l'alimentation s'affiche. Pour en savoir plus, voir l'Aide en ligne d'iDRAC. Surveillance de l'alimentation à l'aide de RACADM Pour afficher les informations de surveillance de l'alimentation, utilisez les objets du groupe System.
Exécution d'opérations de contrôle de l'alimentation iDRAC permet d'exécuter à distance une mise sous tension, une mise hors tension, une réinitialisation, un arrêt normal, une interruption NMI (Non-Masking Interrupt) ou un cycle d'alimentation à l'aide de l'interface Web ou RACADM. Vous pouvez également exécuter ces opérations à l'aide des services à distance Lifecycle Controller ou de WS-Management.
consommation d'alimentation augmente au fil du temps et que le serveur atteint presque sa consommation d'alimentation maximale, l'iDRAC peut demander une augmentation de la consommation d'alimentation potentielle maximale, ce qui augmente l'enveloppe d'alimentation. L'iDRAC augmente uniquement sa demande de consommation d'alimentation potentielle maximale au CMC. Il ne demande pas une alimentation minimale potentielle inférieure si la consommation diminue.
La page Configuration de l'alimentation s'affiche. La limite de la stratégie d'alimentation actuelle figure dans la section Stratégie de limite d'alimentation active. 2. Sélectionnez Activer sous Stratégie de limite d'alimentation iDRAC. 3. Dans la section Limites définies par l'utilisateur, entrez la limite de puissance maximale en watts et en BTU/h ou le pourcentage maximal de limite système recommandée. 4. Cliquez sur Appliquer pour appliquer les valeurs.
restantes de fonctionner avec une charge plus élevée et plus efficacement. Pour cela, il est nécessaire que les unités d'alimentation prennent en charge cette fonction pour qu'elles se mettent sous tension rapidement lorsque cela est nécessaire. Dans un système à deux UC, l'UC1 ou UC2 peut être configurée en tant qu'UC principale. Dans un système à quatre UC, vous devez définir la paire d'UC (1+1 ou 2+2) en tant qu'UC principale.
Configuration des options d'alimentation à l'aide de l'utilitaire de configuration d'iDRAC Pour configurer les options d'alimentation : 1. Dans l'utilitaire de configuration d'iDRAC, accédez à Configuration de l'alimentation. REMARQUE : Le lien Configuration de l'alimentation est disponible uniquement si l'unité d'alimentation du serveur prend en charge la surveillance de l'alimentation. La page Paramètres iDRAC - Configuration de l'alimentation s'affiche. 2.
12 Configuration, surveillance et inventaire des périphériques réseau Vous pouvez inventorier, surveiller et configurer les périphériques réseau suivants : • • • • • Cartes d'interface réseau (NIC) Adaptateurs réseau de convergence (CNA) Cartes LOM (LAN On Motherboard) Cartes NCD (Network Daughter Card) Cartes mezzanines (uniquement pour les serveurs lames) Concepts connexes Inventaire et surveillance des périphériques HBA FC Configuration dynamique des adresses virtuelles, de l’initiateur et de la cible
(Guide de référence de l'interface de ligne de commande RACADM iDRAC8) à l'adresse dell.com/ idracmanuals. D'autres propriétés peuvent être affichées lors de l'utilisation de l'interface RACADM ou de WS-MAN en plus des propriétés affichées dans l'interface Web iDRAC. Inventaire et surveillance des périphériques HBA FC Vous pouvez surveiller l'intégrité à distance et afficher l'inventaire des adaptateurs de bus hôte Fibre Channel (HBA FC) dans le système géré.
• WWPN virtuel REMARQUE : Lorsque vous désactivez la stratégie de persistance, toutes les adresses virtuelles sont réinitialisées à l’adresse permanente par défaut définie en usine. REMARQUE : Sur les cartes avec des attributs FIP virtuel, WWN virtuel et MAC WWPN virtuel, les attributs de MAC WWPN et de WWN virtuels sont configurés automatiquement lorsque vous configurez le FIP virtuel.
Fabricant Type • 5720 bNDC 1 Go Intel • • • • • • • • • • i350 Mezz 1 Gbit x520+i350 rNDC 10 Gbit+1 Gbit I350 bNDC 1 Gbit x540 PCIe 10 Gbit x520 PCIe 10 Gbit i350 PCIe 1 Gbit x540+i350 rNDC 10 Gbit+1 Gbit i350 rNDC 1 Gbit x520 bNDC 10 Gbit 40G 2P XL710 rNDC QSFP+ Mellanox • • • • • • ConnectX-3 10G ConnectX-3 40G ConnectX-3 10G ConnectX-3 Pro 10G ConnectX-3 Pro 40G ConnectX-3 Pro 10G QLogic • • • QME2662 Mezz FC16 QLE2660 PCIe FC16 QLE2662 PCIe FC16 Emulex • • • • • • • • • • • • • • • • • • •
REMARQUE : L'optimisation d'identité d'E/S n'est pas prise en charge sur la carte suivante : • Intel x520 Mezz 10 Go Version du BIOS prise en charge pour l'optimisation d'identité des E/S Dans les serveurs Dell PowerEdge de 13e génération, la version du BIOS est disponible par défaut. Le tableau suivant répertorie la version BIOS minimale prise en charge sur les serveurs PowerEdge de 12e génération.
État de la fonction FlexAddress dans le CMC Mode défini dans la configuration iDRAC État de la Configuration fonction XML d’identité d’E/S dans l’iDRAC Stratégie de persistance Effacer la stratégie de persistance : adresses virtuelles virtuelles (VAM) configurée FlexAddress activé Mode FlexAddress Activé VAM non configuré Définir sur Flex Address Pas de persistance Défini sur Flex Address FlexAddress activé Mode Flex Address Désactivé Configuré à l’aide du chemin défini dans le Lifecycle Contr
État de la fonction FlexAddress dans le CMC Mode défini dans la configuration iDRAC État de la Configuration fonction XML d’identité d’E/S dans l’iDRAC Stratégie de persistance Effacer la stratégie de persistance : adresses virtuelles Flex Address activé Mode console Activé VAM non configuré Définir sur l’adresse MAC du matériel Définir sur l’adresse MAC du matériel Flex Address activé Mode console Désactivé Configuré à l’aide du chemin défini dans le Lifecycle Controller La configuration du
Serveur avec fonction de stratégie de persistance VAM État de la fonction FlexAddress dans le CMC État de la fonction d’identité d’E/S dans l’iDRAC Activée Désactivée Activée Activée Désactivée Désactivée Activée Disponibilité de Source de VA d’agent à programmatio distance pour n VA le cycle de redémarrage Comportement de persistance de VA de cycle de redémarrage FlexAddress depuis CMC Spécification par FlexAddress Oui : Nouveau ou persistant Adresse virtuelle de l’agent distant Paramètre d
Activation ou désactivation de l'optimisation d'identité d'E/S via l'interface Web Pour activer ou désactiver l'optimisation d'identité d'E/S : 1. Dans l'interface Web iDRAC, accédez à Présentation générale → Matériel → Périphériques réseau. La page Périphériques réseau s'affiche. 2. Cliquez sur l’onglet Optimisation d’identité d’E/S et sélectionnez l’option Optimisation d’identité d’E/S pour activer cette fonction. Pour la désactiver, désélectionnez cette option. 3.
• Activer l'optimisation d'identité d'E/S Les événements sont journalisés dans le journal du Lifecycle Controller dans les cas suivants : • L'optimisation de l’identité d’E/S est activée ou désactivée. • La stratégie de persistance est modifiée. • L'adresse virtuelle, l’initiateur et les valeurs cibles sont définies selon la stratégie.
• Pour les adresses virtuelles, utilisez les objets iDRAC.IOIDOpt.VirtualAddressPersistencePolicyAuxPwrd et iDRAC.IOIDOpt.VirtualAddressPersistencePolicyNonAuxPwrd • Pour l'initiateur, utilisez l'objet iDRAC.IOIDOPT.InitiatorPersistencePolicy • Pour les cibles de stockage, utilisez l'objet iDRAC.IOIDOpt.
Tableau 25. Valeurs par défaut des attributs de cibles de stockage iSCSI Attributs de cibles de stockage iSCSI Valeurs par défaut en mode IPv4 Valeurs par défaut en mode IPv6 ConnectFirstTgt Désactivée Désactivée FirstTgtIpAddress 0.0.0.
Gestion de périphériques de stockage 13 Dans la version 2.00.00.00 de l’iDRAC, iDRAC développe sa gestion sans agent pour inclure la configuration directe des nouveaux contrôleurs PERC 9. Il vous permet de configurer à distance les composants de stockage connectés à votre système au moment de l’exécution. Ces composants comprennent des contrôleurs RAID et non RAID et les ports, canaux, boîtiers et disques qui leur sont associés.
• Boîtier : il est relié au système en externe tandis que le fond de panier et ses disques physiques sont internes. • Fond de panier : similaire à un boîtier. Dans un fond de panier, le connecteur de contrôleur et les disques physiques sont reliés au boîtier, mais il ne dispose pas des fonctionnalités de gestion (capteurs de température, alarmes, etc.) associées aux boîtiers externes. Les disques physiques peuvent faire partie d’un boîtier ou être connectés au fond de panier d'un système.
Clignotement ou annulation du clignotement des LED des composants Références connexes Contrôleurs pris en charge Boîtiers pris en charge Récapitulatif des fonctions prises en charge pour les périphériques de stockage Présentation des concepts RAID Storage Management utilise la technologie RAID (Redundant Array of Independent Disks) pour fournir une capacité de Storage Management.
Concepts de RAID La technologie RAID utilise des techniques particulières pour l'écriture des données sur les disques. Ces techniques permettent au RAID de fournir une redondance des données ou de meilleures performances. Ces techniques comprennent : • Mise en miroir : duplication des données d'un disque physique à un autre. La mise en miroir fournit une redondance des données en conservant deux copies des mêmes données sur différents disques physiques.
largement suffire, comparé à un autre selon les applications dans l'environnement de fonctionnement et la nature des données stockées. Lorsque vous choisissez un niveau de RAID, vous pouvez vous attendre aux performances et aux éléments à prendre en compte en matière de coût suivants : • Disponibilité et tolérance aux pannes : cela fait référence à la capacité d'un système à maintenir ses opérations et fournir un accès aux données même lorsque l'un de ses composants est en panne.
RAID 0 • Disques des groupes n comme disque virtuel important doté d'une capacité de (taille de disque la plus petite) *n disques. • Les données sont stockées sur les disques de manières alternative. • Aucune donnée de redondance n'est conservée. Lorsqu'un disque échoue, le disque virtuel important échoue sans pouvoir recréer les données de quelque façon que ce soit. • Les performances de lecture-écriture sont meilleures.
Caractéristiques de RAID 1 : • Disques des groupes n + n comme disque virtuel d'une capacité de n disques. Les contrôleurs actuellement pris en charge par Storage Management permettent de sélectionner deux disques au moment de la création d'un RAID 1. Étant donné que ces disques sont en miroir, la capacité totale de stockage correspond à un disque. • Les données sont répliquées sur les deux disques. • Lorsqu'un disque échoue, le disque virtuel fonctionne toujours.
Caractéristiques de RAID 5 : • Disques des groupes n comme disque virtuel important d'une capacité de (n-1) disques. • Les informations redondantes (parité) sont stockées de manière alternative sur tous les disques. • Si un disque échoue, le disque virtuel fonctionne encore, cependant il fonctionne en mode dégradé. Les données sont reconstruites à partir des disques restants. • Meilleures performances de lecture, mais performances d'écriture plus lentes. • Redondance pour la protection des données.
Caractéristiques de RAID 6 : • Disques des groupes n comme disque virtuel important d'une capacité de (n-2) disques. • Les informations redondantes (parité) sont stockées de manière alternative sur tous les disques. • Le disque virtuel demeure fonctionnel avec jusqu'à deux pannes de disque. Les données sont reconstruites à l'aide des disques restants. • Meilleures performances de lecture, mais performances d'écriture plus lentes. • Redondance accrue pour la protection des données.
Caractéristiques de RAID 50 : • Disques de groupes n*s comme disque virtuel important avec une capacité de s*(n-1), où s correspond au nombre de répartitions et n au nombre de disques sur chaque répartition. • Les informations redondantes (parité) sont stockées de manière alternative sur tous les disques de chaque répartition RAID 5. • Meilleures performances de lecture, mais performances d'écriture plus lentes. • Nécessite autant d'informations de parité que RAID 5 standard.
Caractéristiques de RAID 60 : • Regroupe les disques n*s comme disque virtuel important avec une capacité de s*(n-2), où s correspond au nombre de répartitions et n au nombre de disques sur chaque répartition. • Les informations redondantes (parité) sont stockées de manière alternative sur tous les disques de chaque répartition RAID 6. • Meilleures performances de lecture, mais performances d'écriture plus lentes.
Caractéristiques de RAID 10 : • Disques de groupes n comme disque virtuel important avec une capacité de (n/2) disques, où n est un nombre entier pair. • Les images miroir des données sont segmentées sur les ensembles de disques physiques. Ce niveau fournit la redondance via la mise en miroir. • Lorsqu'un disque échoue, le disque virtuel fonctionne encore. Les données sont lues à partir du disque en miroir restant. • Meilleures performances de lecture et d'écriture.
Tableau 26. Comparaison des performances des niveaux RAID Adresse RAID Disponibilité Performanc Performanc des données es de lecture es d'écriture Performanc es de recréaction Nombre minimal de disques requis Usages suggérés RAID 0 Aucun Très bon Très bon S/O N Données non critiques RAID 1 Excellent Très bon Bon Bon 2N (N = 1) Petites bases de données, journaux de base de données et informations critiques RAID 5 Bon Lectures séquentielles : bon.
Adresse RAID Disponibilité Performanc Performanc des données es de lecture es d'écriture Performanc es de recréaction Nombre minimal de disques requis RAID 60 Excellent Médiocre X x (N + 2) (N Informations = au moins 2) critiques.
Boîtiers pris en charge iDRAC prend en charge les boîtiers MD1400 et MD1420.. Récapitulatif des fonctions prises en charge pour les périphériques de stockage Le tableau suivant fournit les fonctions prises en charge par les périphériques de stockage par le biais d’iDRAC. REMARQUE : Les fonctionnalités telles que la préparation au retrait et l'activation ou la désactivation du clignotement LED de composant ne s'appliquent pas aux cartes SSD PCIe HHHL.
Nom de la fonction Contrôleurs PERC 9 Contrôleurs PERC 8 SSD PCIe H83 H73 0 0P H730 H330 FD33 xS FD33 xD H810 H710P H710 H310 Annuler l’initialisation En tem ps réel En tem ps réel En temp s réel En temp s réel En temp s réel En temp s réel Sans objet Sans objet Sans objet Sans objet Cryptez des disques virtuels En tem ps réel En tem ps réel En temp s réel En temp s réel En temp s réel En temp s réel Interm Interm édiair édiaire e Interm Inter Sans édiair média objet e ire Af
Nom de la fonction Contrôleurs PERC 9 H83 H73 0 0P Contrôleurs PERC 8 H730 H330 FD33 xS FD33 xD H810 H710P H710 H310 SSD PCIe Mode de recopie En tem ps réel En tem ps réel En temp s réel En temp s réel En temp s réel En temp s réel Interm Interm édiair édiaire e Interm Inter Sans édiair média objet e ire Mode d’équilibrage de charge En tem ps réel En tem ps réel En temp s réel En temp s réel En temp s réel En temp s réel Interm Interm édiair édiaire e Interm Inter Sans édiair médi
Nom de la fonction Contrôleurs PERC 9 H83 H73 0 0P Contrôleurs PERC 8 H730 H330 FD33 xS FD33 xD H810 En temp s réel En temp s réel En temp s réel En temp s réel Interm Interm édiair édiaire e Interm Inter Sans édiair média objet e ire Faire l'inventaire et surveiller à distance l’intégrité des périphériques SSD PCIe Sans Sans Sans obje obje objet t t Sans objet Sans objet Sans objet Sans objet Sans objet Sans objet Sans objet En temps réel Préparez le retrait du SSD PCIe Sans Sans Sa
Toutefois, RACADM et WS-MAN affichent des informations pour la plupart des périphériques de stockage du système. Les derniers événements de stockage et la topologie des périphériques de stockage sont également affichés. Des alertes et des interruptions SNMP sont générées pour les événements de stockage. Les événements sont consignés dans le journal Lifecycle.
Pour afficher la topologie des périphériques de stockage, accédez à Présentation → Stockage → Topologie. La page Topologie affiche une représentation hiérarchique des composants de stockage dans le système. Cliquez sur les liens pour afficher les détails des composants respectifs.
• • • • Assurez-vous que le Lifecycle Controller est activé. Si aucun disque n'est à l’état Prêt, insérez d’autres disques et assurez-vous que les disques sont à l’état Prêt. Si aucun disque virtuel n'est présent, créez au moins un disque virtuel. Si les disques physiques sont en mode non RAID, convertissez-les en mode RAID avec les interfaces iDRAC, notamment l’interface Web, RACADM ou WS-MAN, ou avec .
Vous pouvez convertir les disques physiques en disques RAID ou non RAID : • • en utilisant les interfaces iDRAC telles que l'interface Web, RACADM ou WS-Man. en appuyant sur la combinaison de touches Ctrl+R lors du redémarrage du serveur, puis en sélectionnant le contrôleur requis. REMARQUE : La conversion du mode n’est pas prise en charge sur les contrôleurs matériels PERC fonctionnant en mode HBA .
• Supprimer • Modifier les règles • Initialiser • Vérifier la cohérence • Annuler la vérification de cohérence • Cryptez des disques virtuels • Affecter ou annuler l’affectation de disques de secours dédiés • Faire clignoter la LED et Arrêter le clignotement de la LED de disques virtuels Concepts connexes Création de disques virtuels Modification des règles de cache des disques virtuels Suppression de disques virtuels Vérification de cohérence de disque virtuel Initialisation des disques vir
REMARQUE : Si vous créez un disque virtuel en mode Ajouter à une opération en attente et qu'une tâche n'est pas créée, puis si vous supprimez le disque virtuel, l'opération de création de disque virtuel en attente est désactivée.
3. Dans la section Sélectionner les disques virtuels, sélectionnez le nombre de disques physiques. Pour plus d'informations sur les champs, voir l'Aide en ligne d'iDRAC. 4. Depuis le menu déroulant Appliquer le mode de fonctionnement, sélectionnez le moment auquel vous souhaitez appliquer les paramètres. 5. Cliquez sur Create Virtual Disk (Créer un disque virtuel). Les paramètres sont appliqués en fonction du mode de fonctionnement sélectionné.
problèmes lorsque des mesures sont prises en supposant que les données sont disponibles sur le disque. • Forcer l'écriture différée : la mémoire cache d'écriture est activée, que le contrôleur dispose ou non d'une batterie. Si le contrôleur ne dispose pas d'une batterie et que la mise en mémoire cache d'écriture différée est utilisée, une perte de données peut survenir en cas de panne d'alimentation. La règle de cache de disque s’applique aux lectures d’un disque virtuel particulier.
Vous devez disposer du privilège de connexion et de contrôle du serveur pour vérifier la cohérence des disques virtuels. Initialisation des disques virtuels L’initialisation des disques virtuels efface toutes les données sur le disque, mais ne modifie pas la configuration du disque virtuel. Vous devez initialiser un disque virtuel qui est configuré avant de pouvoir l’utiliser. REMARQUE : N'initialisez pas les disques virtuels si vous tentez de recréer une configuration existante.
Si l’initialisation complète d’un disque virtuel est effectuée, l’initialisation en arrière-plan n’est pas obligatoire. Au cours de l’initialisation complète, l’hôte ne peut pas accéder au disque virtuel. Si vous redémarrez le système pendant une initialisation complète, l’opération se termine et une initialisation en arrière-plan démarre sur le disque virtuel. Il est recommandé de toujours faire une initialisation complète sur les disques qui contenaient des données auparavant.
Gestion de disques virtuels à l’aide de l’interface Web 1. Dans l’interface Web d’iDRAC, accédez à Présentation → Stockage → Disques virtuels → Gérer. La page Gestion de disques virtuels s’affiche. 2. Dans le menu déroulant Contrôleur, sélectionnez le contrôleur dont vous souhaitez gérer les disques virtuels. 3. Pour un ou plusieurs disques virtuels, à partir de chaque menu déroulant Action, sélectionnez une action. Vous pouvez spécifier plusieurs actions pour un lecteur virtuel.
• Vérifier la cohérence • Crypter le disque virtuel : crypte le disque virtuel. Si le contrôleur est doté de capacités de cryptage, vous pouvez créer, modifier ou supprimer les clés de sécurité. REMARQUE : L'option Crypter le disque virtuel est disponible uniquement si le disque virtuel est créé à l'aide de disques à cryptage automatique (SED). • Gérer les disques de secours dédiés : attribue ou annule l’attribution d’un disque physique en tant que disque de secours dédié.
• Mode de lecture cohérente (automatique ou manuelle) • Démarrer ou arrêter la lecture cohérente si le mode de lecture cohérente est Manuel • Zones non configurées de la lecture cohérente • Mode de vérification de cohérence • Mode de recopie • Mode d’équilibrage de charge • Taux de vérification de cohérence • Taux de recréation • Taux d'initialisation en arrière-plan (BGI) • Taux de reconstruction • Configuration étrangère d'importation automatique optimisée • Créez ou modifiez les cl
Équilibrage de charge La propriété d’équilibrage de charge vous permet d’utiliser automatiquement les deux ports ou connecteurs de contrôleur connectés au même boîtier pour acheminer les requêtes d’E/S. Cette propriété est disponible uniquement sur les contrôleurs SAS. Taux d'initialisation en arrière-plan (BGI) L'initialisation en arrière-plan d'un disque virtuel redondant sur les contrôleurs PERC débute automatiquement dans un délai de 0 à 5 minutes après la création d'un disque virtuel.
(SED). Vous ne pouvez créer qu’une seule clé de cryptage pour chaque contrôleur doté de la capacité de cryptage. La clé de sécurité est gérée à l’aide de fonction LKM (Local Key Management, Gestion de clés locale). LKM sert à générer l’ID de clé et le mot de passe ou la clé nécessaire pour sécuriser le disque virtuel. Si vous utilisez la fonction LKM, vous devez créer la clé de cryptage en spécifiant l’Identifiant de clé de sécurité et la Phrase de passe.
• Pour spécifier le pourcentage des ressources du contrôleur dédiées à l’exécution de l’initialisation en arrière-plan (BGI) d’un disque virtuel après sa création, utilisez l'objet Storage.Controller.BackgroundInitializationRate • Pour spécifier le pourcentage des ressources du contrôleur dédiées à la reconstruction d'un groupe de disques après l'ajout d'un disque physique ou la modification du niveau de RAID d'un disque virtuel résidant sur le groupe de disques, utilisez l'objet Storage.Controller.
l'état Étranger, il contient alors la totalité ou une partie d'un disque virtuel, ou est attribué en tant que disque de secours. REMARQUE : La tâche Importer la configuration étrangère importe tous les disques virtuels résidant sur les disques physiques qui ont été ajoutés au contrôleur. Si plusieurs disques virtuels étrangers sont présents, toutes les configurations étrangères sont importées.
Pour importer automatiquement les configurations étrangères, dans la section Configurer les propriétés du contrôleur, activez l’option Importation étrangère optimisée de configuration étrangère, sélectionnez l'option Appliquer le mode de fonctionnement, puis cliquez sur Appliquer. REMARQUE : Vous devez redémarrer le système après avoir activé l’option Importation étrangère optimisée de configuration étrangère pour que les configurations étrangères prennent effet.
Réinitialisation de la configuration d'un contrôleur Vous pouvez réinitialiser la configuration d’un contrôleur. Cette opération supprime les disques virtuels et désattribue tous les disques de secours du contrôleur. Cela ne supprime que les disques de la configuration et n’efface aucune autre donnée. La réinitialisation de la configuration ne supprime pas de configurations étrangères. Le support en temps réel de cette fonctionnalité est uniquement disponible dans le micrologiciel PERC 9.1.
• Toute clé de sécurité locale associée à des disques autocryptables (SED) doit être supprimée. • Le contrôleur ne doit pas avoir un cache préservé. • Vous disposez de privilèges de contrôle du serveur pour basculer le mode du contrôleur. REMARQUE : Assurez-vous de sauvegarder la configuration étrangère, la clé de sécurité, les disques virtuels et les disques de secours avant de changer le mode car les données sont supprimées.
Redémarrez le système pour que la modification prenne effet. Basculement du mode de contrôleur à l’aide de RACADM Pour basculer le mode du contrôleur à l’aide de RACADM, exécutez les commandes suivantes : • Pour afficher le mode actuel du contrôleur, à l’invite RACADM, exécutez la commande $ racadm get Storage.Controller.1.RequestedControllerMode[key=. La sortie suivante s’affiche : RequestedControllerMode = NONE.
Surveillance de l'analyse de la prédiction d'échec sur des disques Storage Management prend en charge la technologie SMART (Self Monitoring Analysis and Reporting Technology) sur les disques physiques compatibles SMART. SMART effectue une analyse qui prédit les échecs sur chaque disque et envoie des alertes si un échec de disque est prévu. Les contrôleurs vérifient si les disques physiques risquent d’échouer et, le cas échéant, transmettent ces informations à l’iDRAC.
• Planifier plusieurs tâches à exécuter ultérieurement à l’aide des options de planification. Gestion des SSD PCIe Le disque SSD (solid state device) PCIe (Peripheral Component Interconnect Express) est un périphérique de stockage hautes performances conçu pour des solutions exigeant une faible latence, des IOPS (Opérations d'entrée/sortie par seconde) élevées et une fiabilité et facilité de stockage de niveau entreprise.
Inventaire et surveillance de SSD PCIe En intermédiaire ou en temps réel, les informations d’inventaire et de surveillance suivantes sont disponibles pour les SSD PCIe : • Informations relatives au matériel : – Carte de l'extenseur SSD PCIe – Fond de panier SSD PCIe • L’inventaire des logiciels inclut uniquement la version du micrologiciel du SSD PCIe.
REMARQUE : • Le remplacement à chaud ordonné est pris en charge uniquement lorsque des SSD PCIe sont installés sur un système pris en charge exécutant un système d'exploitation pris en charge. Pour vous assurer de disposer de la bonne configuration pour votre SSD PCIe, consultez le Manuel du propriétaire. • La tâche Préparation au retrait n'est pas prise en charge pour les SSD PCIe sur les systèmes VMware vSphere (ESXi) et les périphériques SSD PCIe HHHL.
Si la tâche est créée avec succès, un message indiquant que l’ID de tâche est créée sur le contrôleur sélectionné s’affiche. Cliquez sur File d’attente pour visualiser l’avancement de la tâche dans la page File d’attente. Si l’opération en attente n’est pas créée, un message d’erreur s’affiche. Si l’opération en attente réussit et la création de tâche n’est pas exécutée avec succès, un message d’erreur s’affiche.
Si vous avez sélectionné Effacement sécurisé et que vous souhaitez afficher les autres options du menu déroulant, sélectionnez Action, puis cliquez sur le menu déroulant pour afficher les autres options. 4. Dans le menu déroulant Appliquer le mode de fonctionnement, sélectionnez l'une des options suivantes : • • Au prochain redémarrage : sélectionnez cette option pour appliquer les actions au cours du prochain redémarrage du système. Il s’agit de l’option par défaut pour les contrôleurs PERC 8.
• • • • Afficher les propriétés Configurer le mode universel ou mode divisé Afficher les informations sur le logement (universel ou partagé) Définir le mode SGPIO Concepts connexes Récapitulatif des fonctions prises en charge pour les périphériques de stockage Boîtiers pris en charge Configuration du mode du fond de panier Affichage des logements universels Définition du mode SGPIO Configuration du mode du fond de panier Les serveurs Dell PowerEdge de 13e génération prennent en charge une nouvelle topolo
démarrage car le second contrôleur ne voit aucun disque. En outre, le premier contrôleur voit une configuration étrangère. Si vous ignorez cette erreur, les disques virtuels existants sont perdus. Configuration du mode du fond de panier à l’aide de l’interface Web Pour configurer le mode du fond de panier à l’aide de l’interface Web iDRAC : 1. Dans l'interface Web iDRAC, allez à Présentation → Stockage → Boîtiers → Configuration. La page Configuration du boîtier s’affiche. 2.
6. Exécutez la commande suivante pour créer une tâche : jobqueue create -s TIME_NOW --realtime Un ID de tâche est renvoyé. 7. Exécutez la commande suivante pour interroger l’état de la tâche : jobqueue view -i JID_xxxxxxxx où JID_xxxxxxxx est l’ID de la tâche de l’étape 6. L’état est affiché comme En attente. Continuez à interroger l’ID de tâche jusqu’à ce que l'état Terminé s'affiche (ce processus peut prendre jusqu’à trois minutes). 8.
L'état d’intégrité cumulative du boîtier fournit l’état de l’intégrité de tous les lecteurs de l’enceinte. Le lien du boîtier sur la page Topologie affiche l’ensemble des informations du boîtier, peu importe le contrôleur auquel il est associé. Comme deux contrôleurs de stockage (PERC et extenseur PCIe) peuvent être connectés au même fond de panier, seul le fond de panier associé au contrôleur PERC s’affiche dans la page Inventaire du système.
Choix du mode de fonctionnement pour l'application des paramètres Lors de la création et la gestion des disques virtuels, la configuration des disques physiques, contrôleurs et boîtiers ou la réinitialisation des contrôleurs, avant d’appliquer les paramètres, vous devez sélectionner le mode de fonctionnement.
• Ajouter aux opérations en attente : sélectionnez cette option pour créer une opération en attente pour appliquer les paramètres. Vous pouvez afficher tous les opérations en attente d'un contrôleur dans la page Présentation → Stockage → Opérations en attente. REMARQUE : • 3. L’option Ajouter aux opérations en attente n’est pas applicable à la page Opérations en attente pour les SSD PCIe sur la page Disques physiques → Configuration.
• • • Appliquer maintenant : sélectionnez cette option pour enregistrer toutes les opérations immédiatement. Cette option est disponible pour les contrôleurs PERC 9 équipés de la dernière version de micrologiciel. Au prochain redémarrage : sélectionnez cette option pour valider toutes les opérations au cours du prochain redémarrage du système. Il s’agit de l’option par défaut pour les contrôleurs PERC 8. Cette option est uniquement applicable pour PERC 8 et les versions ultérieures.
• Si l’opération en attente réussit et qu’aucune opération antérieure n'est en attente, la tâche est créée. Si la création de la tâche réussit, un message indiquant que l’ID de tâche est créé pour le périphérique sélectionné s’affiche. Cliquez sur File d’attente des tâches pour afficher la progression de la tâche dans la page File d’attente des tâches. Si la tâche n’est pas créée, un message indiquant que la création de la tâche a échoué s'affiche.
– Cliquez sur Opérations en attente pour afficher les opérations en attente du périphérique. Tant que la tâche n'est pas créée sur le contrôleur sélectionné, ces opérations en attente ne sont pas appliquées. • Si l’opération en attente n’est pas créée correctement et qu’il n'existe aucune opération en attente, un message d’erreur s’affiche.
Faire clignoter ou arrêter le clignotement des LED des composants à l’aide de l’interface Web Pour activer ou désactiver le clignotement d’un LED de composant : 1. Dans l’interface Web d’iDRAC, accédez à l’une des pages suivantes selon vos besoins : • Présentation → Stockage → Identifier : affiche la page Identification des LED des composants, où vous pouvez activer ou désactiver le clignotement des disques physiques, des disques virtuels et des SSD PCIe.
14 Configuration et utilisation de la console virtuelle Vous pouvez utiliser la console virtuelle pour gérer un système distant en utilisant le clavier, la vidéo et la souris sur la station de gestion pour contrôler les périphériques correspondants sur un serveur géré. Il s'agit d'une fonction disponible sous licence pour les serveurs en rack et de type tour. Elle est disponible par défaut dans les serveurs lames.
Tableau 27. Résolutions d'écran prises en charge et taux de rafraîchissement correspondants Résolution d'écran Taux de rafraîchissement (Hz) 720 x 400 70 640 x 480 60, 72, 75, 85 800 x 600 60, 70, 72, 75, 85 1 024 x 768 60, 70, 72, 75, 85 1 280 x 1 024 60 Il est recommandé de configurer la résolution d'affichage minimale 1 280 x 1 024 sur le moniteur.
Configuration du navigateur Web pour utiliser le plug-in Java Installez un environnement JRE (Java Runtime Environment) si vous utilisez Firefox ou IE et voulez utiliser le visualiseur Java. REMARQUE : Installez une version JRE 32 bits ou 64 bits sur un système d'exploitation 64 bits ou une version 32 bits sur un système d'exploitation 32 bits. Pour configurer IE pour utiliser le plug-in Java : • Désactivez les invites automatiques des téléchargements de fichiers dans Internet Explorer.
• Sélectionnez Demander pour Télécharger les contrôles ActiveX signés. • Sélectionnez Activé ou Demander pour Exécuter les contrôles ActiveX et les plug-ins. • 7. Sélectionnez Activé ou Demander pour Contrôles ActiveX reconnus sûrs pour l'écriture de scripts. Cliquez sur OK pour fermer la fenêtre Paramètres de sécurité. 8. Cliquez sur OK pour fermer la fenêtre Options Internet.
Suppression des versions ActiveX antérieures dans IE7 Pour supprimer les anciennes versions du Visualiseur ActiveX pour IE7, procédez comme suit : 1. Fermez Video Viewer et le navigateur Internet Explorer. 2. Rouvrez Internet Explorer et accédez à Internet Explorer → Outils → Gérer les modules complémentaires et cliquez sur Activer ou désactiver les modules complémentaires. La fenêtre Gérer les modules complémentaires s'affiche. 3.
4. Cliquez sur Importer, accédez au certificat CA (dans le format codé en base 64), sélectionnez-le et cliquez sur Ouvrir. Le certificat sélectionné est importé dans la banque de certificats de confiance de démarrage Web. 5. Cliquez sur Fermer puis sur OK. La fenêtre du Panneau de configuration Java se ferme.
• Utilisez les objets suivants avec la commande config : – – – – – cfgRACTuneConRedirEnable cfgRACTuneConRedirPort cfgRACTuneConRedirEncryptEnable cfgRacTunePluginType cfgRacTuneVirtualConsoleAuthorizeMultipleSessions Pour plus d'informations sur ces objets, voir l'iDRAC8 RACADM Command Line Interface Reference Guide (Guide de référence de l'interface de ligne de commande RACADM iDRAC8) disponible à l'adresse dell.com/idracmanuals.
ce site Web et sur Installer pour installer les contrôles ActiveX dans la fenêtre Avertissement de sécurité. La session de console virtuelle est lancée.
• • Si la connexion directe est désactivée et que la connexion locale, Active Directory, LDAP ou par carte à puce est activée, la page Ouverture de session correspondante s'affiche. Si la connexion directe est activée, le Visualiseur de console virtuelle s'ouvre et la page Console virtuelle s'affiche en arrière-plan. REMARQUE : Internet Explorer prend en charge les ouvertures de session locales, Active Directory, LDAP, par carte à puce (SC) et par connexion directe.
• Pour les serveurs en rack et de type tour : , , User: , • Pour les serveurs lames : , , , User: , Il peut arriver que le Visualiseur de console virtuelle affiche une vidéo de mauvaise qualité. Ceci est dû à la lenteur de la connectivité réseau qui provoque une perte d'une ou de deux trames vidéo lorsque vous démarrez la session de console virtuelle.
Remplacez les valeurs de motion_threshold et de motion_acceleration par -1. Si vous désactivez l'accélération de la souris dans le bureau GNOME, dans le Visualiseur de console virtuelle, accédez à Outils → Options de session → Souris. Dans l'onglet Accélération de la souris, sélectionnez Aucune. Pour un accès exclusif à la console du serveur géré, vous devez désactiver la console locale et reconfigurer les Sessions max. sur la valeur 1 dans la page Console Virtuelle.
Session de console virtuelle Java-sur le système d'exploitation Windows • La touche Ctrl+Alt+Suppr n'est pas envoyée au système géré, mais elle est toujours interprétée par la station de gestion.
– Ajoutez une entrée à /etc/sysctl.conf – echo 1 > /proc/sys/kernel/sysrq • Lorsque l'envoi de toutes les touches au serveur est activé, les touches magiques SysRq sont envoyées au système d'exploitation du système géré.
REMARQUE : Il n’est donc pas nécessaire d’exécuter une séquence d’interruption avant d’utiliser la touche magique SysRq.
Gestion de Média Virtuel 15 Média Virtuel permet au serveur géré d'accéder aux périphériques de support sur la station de gestion ou aux images de CD/DVD ISO sur un partage de réseau comme s'il s'agissait de périphériques sur le serveur géré.
Figure 4. Configuration Média Virtuel Lecteur et périphériques pris en charge Le tableau suivant répertorie les lecteurs pris en charge via Média Virtuel. Tableau 28.
3. Cliquez sur Appliquer pour enregistrer les paramètres. Configuration de média virtuel à l'aide de RACADM Pour configurer le média virtuel : • Utilisez les objets du groupe iDRAC.VirtualMedia avec la commande set. • Utilisez les objets du groupe cfgRacVirtual avec la commande config. Pour en savoir plus, voir le RACADM Command Line Reference Guide for iDRAC (Guide de référence de ligne de commande RACADM pour iDRAC) à l'adresse dell.com/idracmanuals.
Le média virtuel et RFS sont mutuellement exclusifs. Si la connexion RFS est active et que vous tentez de lancer le client média virtuel, le message d'erreur suivant s'affiche : Le média virtuel est actuellement indisponible. Une session média virtuel ou de partage de fichiers à distance est en cours d'utilisation. Si la connexion RFS n'est pas active, et que vous tentez de lancer le client média virtuel, celui-ci est lancé avec succès.
Pour lancer Média Virtuel lorsque la console virtuelle est désactivée : 1. Dans l'interface Web d'iDRAC, allez à Présentation → Serveur → Console virtuelle. La page Console virtuelle s'affiche. 2. Cliquez sur Lancer Console virtuelle. Le message suivant s'affiche : Virtual Console has been disabled. Do you want to continue using Virtual Media redirection? 3. Cliquez sur OK. La fenêtre Média virtuel s'affiche. 4. Dans le menu Média virtuel , cliquez sur Mappage du CD/DVD ou Mappage de disque amovible.
Lorsque le dossier est ajouté comme image, un fichier .img est créé sur le bureau de la station de gestion d'où la fonction est utilisée. Si ce fichier .img est déplacé ou supprimé, l'entrée correspondante du dossier dans le menu Média Virtuel ne fonctionne pas. Par conséquent, il est recommandé de ne pas déplacer ni de supprimer le fichier .img lorsque l'image est en cours d'utilisation. Toutefois, le fichier .
REMARQUE : L'élément de menu Mappage du lecteur de disquette apparaît dans la liste si l'option Émulation de disquette est activée sur la page de média connecté. Quand Émulation de disquette est activée, Mappage du disque amovible est remplacé par Mappage du lecteur de disquette. L'option Mappage de DVD/CD peut être utilisée pour les fichiers ISO et l’option Mappage de disque amovible peut être utilisée pour les images. 2. Cliquez sur le type de périphérique que vous souhaitez mapper.
4. Accédez à la fenêtre du Client de Média Virtuel. Elle contient les lecteurs corrects qui peuvent être mappés. Concepts connexes Mappage d'un lecteur virtuel Dissociation d'un lecteur virtuel Pour dissocier un lecteur virtuel : 1. Dans le menu Média virtuel, effectuez l'une des opérations suivantes : • Cliquez sur le périphérique dont vous voulez supprimer le mappage. • Cliquez sur Déconnecter le média virtuel. Un message s'affiche vous demandant de confirmer. 2. Cliquez sur Oui.
Activation du démarrage unique pour Média Virtuel Vous pouvez changer la séquence de démarrage uniquement une fois lorsque vous démarrez le système après avoir connecté un périphérique Média Virtuel distant. Avant d'activer l'option de démarrage unique : • Vérifiez que vous disposez du privilège de configuration d'utilisateur. • Associez les lecteurs locaux ou virtuels (CD/DVD, lecteur de disquette ou lecteur Flash USB) au média ou à l'image amorçable en utilisant les options Média Virtuel.
Installation et utilisation de l'utilitaire VMCLI 16 L'utilitaire WMCLI (Virtual Media Command Line Interface) est une interface qui fournit des fonctions de média virtuel de la station de gestion vers iDRAC sur le système géré. Utilisez cet utilitaire pour accéder aux fonctions de média virtuel, notamment aux fichiers images et aux lecteurs physiques, pour déployer un système d'exploitation sur plusieurs systèmes distants dans un réseau.
les commandes VMCLI. Toutefois, pour ajouter ou modifier des utilisateurs dans le groupe Administrateurs VMCLI, utilisez la commande visudo. Syntaxe VMCLI L'interface VMCLI est identique sur les systèmes Windows et Linux. La syntaxe VMCLI est la suivante : VMCLI [paramètre] [options d'environnement du système d'exploitation] Par exemple, vmcli -r iDRAC-IP-address:iDRAC-SSL-port Le paramètre permet à VMCLI de se connecter au serveur défini, d'accéder à iDRAC et de s'adresser au support virtuel spécifié.
Si le fichier n'est pas protégé contre l'écriture, Média Virtuel peut écrire dans le fichier image. Pour que Média Virtuel n'écrive pas sur le support : • Configurez le système d'exploitation pour protéger contre l'écriture un fichier image de disquette qui ne doit pas être remplacé. • Utilisez la fonction de protection contre l'écriture du périphérique. Lors de la virtualisation des fichiers images en lecture seule, plusieurs sessions peuvent utiliser simultanément le même support d'image.
Gestion de la carte SD vFlash 17 La carte SD vFlash est une carte Secure Digital (SD) qui se connecte dans le logement de carte SD vFlash du système. Vous pouvez utiliser une carte de 16 Go maximum. Après avoir inséré la carte, vous devez activer la fonctionnalité vFlash pour créer et gérer des partitions. vFlash est une fonction sous licence.
Affichage des propriétés d'une carte SD vFlash Après avoir activé la fonctionnalité vFlash, vous pouvez afficher les propriétés d'une carte SD à l'aide de l'interface Web iDRAC ou RACADM. Affichage des propriétés d'une carte SD vFlash à l'aide de l'interface Web Pour afficher les propriétés d'une carte SD vFlash, dans l'interface Web d'iDRAC, accédez à Présentation → Serveur → vFlash. La page Propriétés de la carte SD s'affiche.
Activation ou désactivation de la fonctionnalité vFlash à l'aide de l'interface Web Pour activer ou désactiver la fonctionnalité vFlash : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → vFlash. La page Propriétés de la carte SD s'affiche. 2. Sélectionnez ou désélectionnez l'option vFLASH activé pour activer ou désactiver la fonctionnalité vFlash. Si une partition vFlash est connectée, vous ne pouvez pas désactiver vFlash et un message d'erreur s'affiche.
Initialisation d'une carte SD vFlash à l'aide de l'interface Web Pour initialiser une carte vFlash SD : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → vFlash. La page Propriétés de la carte SD s'affiche. 2. Activez vFLASH et cliquez sur Initialiser. Tout le contenu existant est supprimé et la carte est reformatée avec les nouvelles informations système vFlash. Si une partition vFlash est connectée, l'opération d'initialisation échoue et un message d'erreur s'affiche.
REMARQUE : Si iDRAC est réinitialisé, l'état de la dernière opération de partition est perdue. Gestion des partitions vFlash Vous pouvez exécuter les opérations suivantes dans l'interface Web d'iDRAC ou RACADM : REMARQUE : Un administrateur peut exécuter toutes les opérations sur les partitions vFlash. Autrement, vous devez disposer du privilège d'Accès à Média Virtuel pour pouvoir créer, supprimer, formater, connecter ou copier le contenu de la partition.
Une nouvelle partition vide non formatée est créée en lecture seule par défaut. Une page s'affiche pour indiquer le pourcentage d'avancement. Un message d'erreur s'affiche : • La carte est protégée contre l'écriture. • Le nom d'étiquette correspond à l'étiquette d'une partition existante. • Une valeur autre qu'un entier est entrée pour la taille de partition, la valeur dépasse l'espace disponible sur la carte ou la taille de partition est supérieure à 4 Go.
Une partition est créée. Pour le type d'émulation CD, une partition en lecture seule est crée. Pour le type d'émulation Disquette ou Disque dur, une partition lisible et inscriptible est créée. Un message d'erreur s'affiche si : • La carte est protégée contre l'écriture. • Le nom d'étiquette correspond à l'étiquette d'une partition existante. • La taille du fichier image est supérieure à 4 Go ou excède l'espace disponible sur la carte. • Le fichier image n'existe pas ou son extension n'est ni .
• Une opération d'initialisation est déjà en cours d'exécution sur la carte. Affichage des partitions disponibles Vérifiez que la fonctionnalité vFlash est activée pour pouvoir afficher la liste des partitions disponibles. Affichage des partitions disponibles à l'aide de l'interface Web Pour afficher les partitions vFlash, dans l'interface Web iDRAC, accédez à Présentation → Serveur → vFlash → Gérer.
Modification d'une partition à l'aide de RACADM Pour afficher les partitions disponibles et leurs propriétés sur la carte : 1. Ouvrez une console Telnet, SSH ou série sur le système et ouvrez une session. 2.
• Désélectionnez la case de la ou des partitions et cliquez sur Appliquer pour déconnecter les partitions. Les partitions sont connectées ou déconnectées en fonction des sélections effectuées. Connexion ou déconnexion de partitions à l'aide de l'interface RACADM Pour connecter ou déconnecter des partitions : 1. Ouvrez une console Telnet, SSH ou série sur le système et ouvrez une session. 2.
Suppression de partitions existantes à l'aide de l'interface Web Pour supprimer une partition existante : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → vFlash → Gérer. La page Gérer les partitions s'affiche. 2. Dans la colonne Supprimer, cliquez sur l'icône de suppression de la partition à supprimer. Un message s'affiche pour indiquer que l'action va supprimer définitivement la partition. 3. Cliquez sur OK. La partition est supprimée.
Démarrage à partir d'une partition Vous pouvez définir une partition vFlash connectée en tant que périphérique de démarrage pour le démarrage suivant. Avant de démarrer dans une partition,vérifiez que : • La partition vFlash contient une image amorçable (de format .img ou .iso) à démarrer depuis le périphérique. • La fonctionnalité vFlash est activée. • Vous disposez des privilèges d'accès à Média Virtuel.
Utilisation de SMCLP 18 La spécification SMCLP (Server Management Command Line Protocol) permet de gérer les systèmes CLI. Elle définit un protocole pour les commandes de gestion envoyées dans des flux orientés caractère standard. Ce protocole accède à un Gestionnaire CIMOM (Common Information Model Object Manager) en utilisant un groupe de commandes manuelles.
Exécution des commandes SMCLP Vous pouvez exécuter les commandes SMCLP à l'aide d'une interface SSH ou Telnet. Ouvrez une interface SSH ou Telnet et ouvrez une session dans iDRAC comme administrateur. L'invite SMCLP (admin ->) s'affiche. Invites SMCLP : • serveurs lames yx1x, utilisez -$. • serveurs en rack et de type tour yx1x, utilisez admin->. • serveurs lames, en rack et de type tour yx2x, utilisez admin->.
Verbe Définition exit Quitte la session dans l'environnement SMCLP version Affiche les attributs de version d'une cible load Transfère une image binaire d'une URL vers une adresse cible spécifiée Le tableau suivant répertorie les cibles. Tableau 32.
Cible Définitions admin1/system1/sp1/capabilities1/ pwrmgtcap1 Fonctions de service de gestion de l'état de l'alimentation sur le système admin1/system1/sp1/capabilities1/ acctmgtcap* Fonctions de service de gestion de comptes admin1/system1/sp1/capabilities1/ rolemgtcap* Fonctions de gestion basées sur les rôles locaux admin1/system1/sp1/capabilities/ PwrutilmgtCap1 Fonctions de gestion de l'utilisation de l'alimentation admin1/system1/sp1/capabilities1/ elecap1 Fonctions d'authentification adm
Cible Définitions admin1/system1/sp1/rolesvc1 Service d'autorisation basée sur des rôles (RBA) locaux admin1/system1/sp1/rolesvc1/Role1-16 Rôle local admin1/system1/sp1/rolesvc1/Role1-16/ privilege1 Privilège de rôle local admin1/system1/sp1/rolesvc2 Service RBA IPMI admin1/system1/sp1/rolesvc2/Role1-3 Rôle IPMI admin1/system1/sp1/rolesvc2/Role4 Rôle Série sur LAN (SOL) IPMI admin1/system1/sp1/rolesvc3 Service RBA CLP admin1/system1/sp1/rolesvc3/Role1-3 Rôle CLP admin1/system1/sp1/rolesvc3
Utilisation du verbe show Pour en savoir plus sur une cible, utilisez le verbe show. Ce verbe permet d'afficher les propriétés de la cible, des sous-cibles, des associations et la liste des verbes SM-CLP autorisés dans l'emplacement. Utilisation de l'option -display L'option show –display permet de limiter la sortie de la commande à une ou plusieurs propriétés, cibles, associations et un ou plusieurs verbes.
Gestion de l'alimentation du serveur Les exemples suivants expliquent comment utiliser SMCLP pour exécuter des opérations de gestion de l'alimentation sur un système géré.
InstanceID = IPMI:BMC1 SEL Log MaxNumberOfRecords = 512 CurrentNumberOfRecords = 5 Name = IPMI SEL EnabledState = 2 OperationalState = 2 HealthState = 2 Caption = IPMI SEL Description = IPMI SEL ElementName = IPMI SEL Commands: cd show help exit version • Pour afficher l'enregistrement SEL : show/system1/logs1/log1 La sortie suivante s'affiche : /system1/logs1/log1/record4 Properties: LogCreationClassName= CIM_RecordLog CreationClassName= CIM_LogRecord LogName= IPMI SEL RecordID= 1 MessageTimeStamp= 200506
ElementName= IPMI SEL Record Commands: cd show help exit version • Pour effacer le journal SEL : delete /system1/logs1/log1/record* La sortie suivante s'affiche : All records deleted successfully (Tous les enregistrements ont été correctement supprimés). Navigation dans la cible MAP Les exemples suivants montrent comment utiliser le verbe cd pour naviguer dans MAP. Dans tous les exemples, la cible par défaut initiale est supposée être /.
Utilisation de l'iDRAC Service Module 19 L'iDRAC Service Module est une application logicielle recommandée pour une installation sur le serveur (elle n'est pas installée par défaut). Ce module complète iDRAC avec les données de surveillance du système d'exploitation. Elle n'est pas équipée d'une interface, mais complète l'iDRAC en fournissant des données supplémentaires pour fonctionner avec des interfaces iDRAC telles que les interfaces Web, RACADM et WSMAN.
Fonctionnalités de surveillance de l'iDRAC Service Module Le module du service iDRAC fournit les fonctionnalités de surveillance suivantes : • Afficher des informations sur le système d'exploitation (SE) • Réplication des journaux Lifecycle Controller dans les journaux du système d'exploitation. • Options de récupération automatique du système • Remplir les fournisseurs de gestion WMI (Windows Management Instrumentation) • Intégrer avec le rapport pour le Support technique.
L'iDRAC Service Module consigne également les événements qui se produisent lorsque le système d'exploitation ne fonctionne pas. La journalisation du système d'exploitation effectuée par l'iDRAC Service Module suit les normes de journalisation système IETF pour les systèmes d'exploitation Linux. REMARQUE : En commençant par liDRAC Service Module version 2.
Interface CIM WinRM WMIC PowerShell Énumérer les instances d’une classe winrm e wmi/root/ cimv2/dcim/ dcim_account wmic /namespace:\ \root\cimv2\dcim PATH dcim_account Get-WmiObject dcim_account namespace root/ cimv2/dcim winrm g wmi/root/ Obtenir une instance particulière d’une classe cimv2/dcim/ DCIM_Account? CreationClassName= DCIM_Account +Name=iDRAC.Embedd ed.1#Users. 2+SystemCreationCl assName=DCIM_SPCom puterSystem +SystemName=system mc wmic /namespace:\ \root\cimv2\dcim PATH dcim_account wh
Si vous avez activé les fonctions de surveillance iDRAC au cours de l'installation de l'iDRAC Service Module, une fois l'installation terminée, si l'iDRAC Service Module détecte la présence d'OpenManage Server Administrator, il désactive l'ensemble de fonctionnalités de surveillance qui se chevauchent.
20 Utilisation d'un port USB pour la gestion de serveur Sur les serveurs Dell PowerEdge de 12e génération, tous les ports USB sont dédiés au serveur. Dans le cas des serveurs de 13e génération, l’un des ports USB du panneau avant est utilisé par l'iDRAC à des fins de gestion telles que le pré-provisionnement et le dépannage. Le port possède une icône pour indiquer qu’il s’agit d’un port de gestion. Tous les serveurs de 13e génération avec écran LCD prennent en charge cette fonctionnalité.
Pour accéder à l’interface iDRAC via le port USB : 1. Mettez hors tension tous les réseaux sans fil et déconnectez-les de tout autre réseau filaire. 2. Assurez-vous que le port USB est activé. Pour en savoir plus, voir Configuration des paramètres de port de gestion USB. 3. Connectez un câble de type A/A de l’ordinateur portable au port USB de l’iDRAC. Le voyant LED de gestion (le cas échéant) s’allume en vert et reste allumé pendant deux secondes. 4.
d'iDRAC et connecté au serveur. Lorsqu’un périphérique est supprimé du serveur, la configuration du port est réinitialisée et peut être utilisée par iDRAC. – Utilisation SE standard : le périphérique USB est toujours utilisé par le système d’exploitation. – iDRAC direct uniquement : le périphérique USB est toujours utilisé par iDRAC. Vous devez disposer des privilèges de contrôle du serveur pour configurer le port de gestion USB.
4. Cliquez sur Appliquer pour appliquer les paramètres. Configuration du port de gestion USB à l’aide de RACADM Pour configurer le port de gestion USB, utilisez les objets et sous-commandes RACADM : • Pour afficher l’état du port USB : racadm get iDRAC.USB.ManagementPortStatus • Pour afficher la configuration du port USB : racadm get iDRAC.USB.ManagementPortMode • Pour modifier la configuration du port USB : racadm set iDRAC.USB.
configurer un attribut du serveur. Le nom du fichier peut être -config.xml, -config.xml ou config.xml. • Fichier XML de contrôle : comprend des paramètres de contrôle afin de contrôler l’opération d’importation et ne possède pas les attributs d’iDRAC ou d’un autre composant du système. Le fichier de contrôle contient trois paramètres : – ShutdownType : Normal, Forcé, Ne pas redémarrer. – TimeToWait (en secondes) : 300 minimum et 3 600 maximum.
est déjà sous tension que la configuration préparée s’applique même si l’option Ne pas redémarrer est spécifiée. 7. Une fois l’importation terminée, le LCD/LED indique que la tâche est terminée. Si un redémarrage est nécessaire, l’écran LCD affiche l’état de la tâche comme « En suspend, en attente de redémarrage ». 8. Si le périphérique USB reste inséré sur le serveur, le résultat de l’opération d’importation est enregistré dans le fichier results.xml dans le périphérique USB.
Utilisation de la fonction Quick Sync (Synchronisation rapide) d'iDRAC 21 Certains serveurs Dell PowerEdge de 13e génération disposent du cadre Quick Sync qui prend en charge la fonction Quick Sync. Cette fonction permet une gestion au niveau du serveur à partir d’un appareil mobile.
Utilisation d'un appareil mobile pour afficher des informations sur iDRAC Configuration de la fonction Quick Sync (Synchronisation rapide) d'iDRAC À l'aide de l’interface Web iDRAC ou RACADM, vous pouvez configurer la fonction Quick Sync d'iDRAC pour autoriser l’accès au périphérique mobile : • Accès : vous pouvez spécifier l’une des options suivantes pour configurer l’état d’accès de la fonction Quick Sync iDRAC : – Lecture-Écriture : état par défaut.
(Guide de référence de la ligne de commande RACADM iDRAC) disponible à l'adresse dell.com/ esmmanuals. Configuration des paramètres de la fonction Quick Sync (Synchronisation rapide) d'iDRAC à l'aide de l'utilitaire de configuration d'iDRAC Pour configurer iDRAC Quick Sync d'iDRAC : 1. Dans l'utilitaire de configuration d'iDRAC, allez sous Sécurité du panneau avant. 2. Dans la section Quick Sync iDRAC : La page Sécurité du panneau avant des paramètres iDRAC s'affiche. • Spécifiez le niveau d’accès.
22 Déploiement de systèmes d'exploitation Vous pouvez utiliser n'importe quel utilitaire pour déployer des systèmes d'exploitation sur les systèmes gérés : • Interface de ligne de commande CLI Média Virtuel • Console Média Virtuel • Partage de fichier à distance Tâches connexes Déploiement du système d'exploitation à l'aide de VMCLI Déploiement d'un système d'exploitation à l'aide du partage de fichier à distance Déploiement d'un système d'exploitation à l'aide de Média Virtuel Déploiement du systè
Pour déployer le système d'exploitation sur les systèmes distants cibles : 1. Répertoriez les adresses IPv4 iDRAC des systèmes distants cibles dans le fichier texte ip.txt. Indiquez une adresse IPv4 par ligne. 2. Insérez un CD ou un DVD de système d'exploitation amorçable dans le lecteur de la station de gestion. 3. Ouvrez une invite de commande avec les privilèges d'administrateur et exécutez le script vmdeploy : vmdeploy.
Tâches connexes Configuration de l'iDRAC Déploiement d'un système d'exploitation à l'aide du partage de fichier à distance Avant de déployer le système d'exploitation à l'aide de RFS (Remote File Share - Partage de fichiers à distance), vérifiez que : • Les privilèges de Configuration Utilisateur et d'Accès au Média Virtuel d'iDRAC sont activés pour l'utilisateur. • Le partage de réseau contient des pilotes et un fichier d'image amorçable du système d'exploitation dans un format standard, tel que .
RFS et les fonctionnalités de média virtuel sont mutuellement exclusifs. • Si le client média virtuel n'a pas été lancé, et que vous tentez d'établir une connexion RFS, celle-ci est établie et l'image distante devient accessible au système d'exploitation hôte. • Si le client média virtuel a été lancé et que vous tentez d'établir une connexion RFS, le message d'erreur suivant s'affiche : Le Média virtuel est détaché ou redirigé pour le lecteur virtuel sélectionné.
Les caractères suivants sont pris en charge pour le chemin d’accès au fichier d'image, le nom d’utilisateur et le mot de passe : • • • • • Majuscules Minuscules Chiffres de 0 à 9 _, :, ?, <, >, /, \, :,*, |,@ Espace libre REMARQUE : Lorsque vous indiquez les paramètres de partage du réseau, il est conseillé d’éviter l’utilisation des caractères spéciaux dans le nom d’utilisateur et mot de passe ou de crypter en pourcentage les caractères spéciaux. 4. Cliquez sur Appliquer, puis sur Connecter.
–l : emplacement de l'image sur le partage réseau ; utilisez des guillemets doubles autour du nom de l'emplacement.
Déploiement d'un système d'exploitation intégré sur une carte SD Pour installer un hyperviseur intégré sur une carte SD : 1. Insérez les deux cartes SD dans les logements IDSDM (Internal Dual SD Module) sur le système. 2. Activez le module et la redondance SD (si nécessaire) dans le BIOS. 3. Vérifiez que la carte SD est disponible sur l'un des lecteurs lorsque vous appuyez sur lors du démarrage. 4. Déployez le système d'exploitation intégré et suivez les instructions d'installation.
Dépannage d'un système géré à l'aide d'iDRAC 23 Vous pouvez identifier et résoudre les problèmes d'un système géré en utilisant : • la console de diagnostic ; • le code Post ; • les vidéos de démarrage et de blocage ; • l'écran du dernier blocage système ; • les journaux d'événements du système ; • les journaux Lifecycle ; • l'état du panneau avant ; • les voyants des pannes ; • l'intégrité du système.
Planification de diagnostics automatisés à distance Vous pouvez demander des diagnostics automatisés à distance hors ligne sur un serveur en tant qu'événement ponctuel et renvoyer les résultats. Si les diagnostics nécessitent un redémarrage, vous pouvez redémarrer immédiatement ou les planifier lors d'un cycle de maintenance ou un redémarrage suivant (similaire à des mises à jour). Lorsque les diagnostics sont exécutés, les résultats sont collectés et stockés dans le stockage interne d'iDRAC.
• Vous avez des droits de connexion et de contrôle du serveur.
L'écran Capture vidéo affiche les enregistrements vidéo. Pour en savoir plus, voir l'aide en ligne d'iDRAC. Configuration des paramètres de capture vidéo Pour configurer les paramètres de capture vidéo : 1. Dans l'interface Web iDRAC, accédez à Présentation → Serveur → Dépannage → Capture vidéo. La page Capture vidéo s’affiche. 2. 3. Dans le menu déroulant Paramètres de capture vidéo, sélectionnez l’une des options suivantes : • Désactiver : la capture de démarrage est désactivée.
• Pour les serveurs en rack et de type tour : état du panneau avant LCD et du voyant LED d'ID système ou état du panneau avant LED et voyant d'ID système. • Pour les serveurs lames : uniquement les voyants d'ID système. Affichage de l'état du panneau avant LCD Pour afficher l'état du panneau avant LCD des serveurs en rack et de type tour applicables, dans l'interface Web iDRAC, accédez à Présentation → Matériel → Panneau avant. La page Panneau avant s'affiche.
• Défaillance du disque dur • Défaillance du média USB • Endommagement physique En fonction du problème, utilisez les méthodes suivantes pour éliminer le problème : • Remettez le module ou le composant en place et redémarrez le système. • S'il s'agit d'un serveur lame, insérez le module dans une autre baie dans le châssis.
Création du rapport de support technique Si vous devez travailler avec le support technique sur un problème avec un serveur, mais que la politique de sécurité locale empêche la connexion Internet directe, vous pouvez fournir au support technique les données nécessaires pour faciliter le dépannage du problème sans avoir à installer de logiciel ou à télécharger des outils de Dell et sans avoir accès à Internet depuis le système d'exploitation du serveur ou iDRAC.
• Le Lifecycle Controller est activé. • La fonction Collect System Inventory on Restart (CSIOR) (Collecter l'inventaire système au redémarrage) est activée. • Vous avez des droits de connexion et de contrôle du serveur.
du SE du serveur pour collecter et transférer les données vers l’iDRAC. Vous pouvez alors exporter le rapport vers un emplacement réseau local ou partagé. Dans les serveurs Dell PowerEdge de 13e génération, le DUP du collecteur de systèmes d'exploitation est installé en usine. Toutefois, si vous estimez qu'il est absent de l’iDRAC, téléchargez le fichier DUP à partir du site de support de Dell, puis téléversez le fichier vers l'iDRAC à l’aide du processus de mise à jour du micrologiciel.
La page Rapport de support technique s'affiche. 2. Sélectionnez les options pour lesquelles vous voulez collecter les données : • Matériel pour exporter le rapport vers un emplacement situé sur le système local. • Données du SE et d'application pour exporter le rapport vers un partage réseau et spécifier les paramètres réseau.
sélectionner le serveur concerné, puis cliquez sur le bouton du milieu. Les messages d'erreur et d'avertissement s'affichent sur la deuxième ligne. Pour la liste des messages d'erreur affichés sur l'écran LCD, voir le manuel du propriétaire du serveur. Redémarrage d'iDRAC Vous pouvez redémarrer iDRAC à chaud ou à froid sans mettre le serveur hors tension : • Redémarrage à froid : sur le serveur, appuyez sur le bouton LED et maintenez-le enfoncé pendant 15 secondes.
Vous pouvez supprimer un ou plusieurs composants du système à l’aide de la commande SystemErase : racadm systemErase où • BIOS : restauration des valeurs par défaut du BIOS • DIAG : diagnostics intégrés • DRVPACK : pack de pilotes du SE intégré • LCDATA : effacer les données du Lifecycle Controller • IDRAC : restauration des valeurs par défaut d'iDRAC Pour en savoir plus, voir le iDRAC RACADM Command Line Reference Guide (Guide de référence de ligne de com
Questions fréquemment posées 24 Cette section contient les questions courantes sur les éléments suivants : • Journal des événements système • Sécurité du réseau • Active Directory • Connexion directe • Ouverture de session avec une carte à puce • Console virtuelle • Média virtuel • Carte SD vFlash • Authentification SNMP • Périphériques de stockage • iDRAC Service Module • RACADM • Divers Journal des événements système Lors de l'utilisation de l'interface Web iDRAC via Internet E
Sécurité du réseau Lors de l'accès à l'interface Web d'iDRAC, un avertissement de sécurité s'affiche pour indiquer que le certificat SSL émis par l'autorité de certification (CA) n'est pas fiable. iDRAC contient un certificat de serveur par défaut iDRAC pour protéger le réseau lors de l'accès via l'interface Web et l'interface distante RACADM. Ce certificat n'est pas émis par une autorité CA de confiance.
– L'option Activation Active Directory est sélectionnée dans la page Configuration et gestion d'Active Directory. – Le paramètre DNS est correct dans la page Configuration réseau iDRAC . – Le certificat CA racine Active Directory correct est téléversé vers iDRAC si la validation de certificat a été activée. – Le nom iDRAC et le nom de domaine iDRAC correspondent à la configuration de l'environnement Active Directory si vous utilisez le schéma étendu.
Il doit s'agir du nom d'hôte (nom de domaine complet qualifié) ou de l'adresse IP du (ou des) contrôleur(s) de domaine qui gère(nt) le domaine dans lequel l'objet iDRAC réside. Quand faut-il définir une adresse (ou des adresses) de catalogue global ? Si vous utilisez le schéma standard et que les utilisateurs et les groupes de rôles appartiennent à des domaines différents, une adresse (ou plusieurs adresses) de catalogue global est nécessaire.
présents dans le même domaine enfant et l'utilisateur est membre du groupe. Lors de l'ouverture d'une session dans iDRAC en utilisant l'utilisateur présent dans le domaine enfant, l'ouverture de session par connexion directe Active Directory échoue. Ce problème peut être provoqué par un type de groupe incorrect.
1. Dans la fenêtre de Éditeur de stratégie de groupe locale, accédez à Paramètres de l'ordinateur local → Paramètres Windows → Paramètres de sécurité → Stratégies locales → Options de sécurité. 2. Cliquez avec le bouton droit de la souris sur Sécurité réseau : Restreindre NTLM : trafic NTLM sortant vers le serveur distant et sélectionnez Propriétés. 3. Cliquez sur Autoriser tous, puis sur OK et fermez la fenêtre Éditeur de stratégie de groupe local. 4. Accédez à Démarrer et exécutez cmd.
Déterminez si la carte à puce est verrouillée suite à un trop grand nombre de tentatives avec un code PIN incorrect. Dans ce cas, contactez l'émetteur de la carte à puce de l'entreprise pour obtenir une nouvelle carte. Console virtuelle Une session de console virtuelle est active, même si vous avez fermé la session dans l'interface Web iDRAC. Est-ce normal ? Oui. Fermez la fenêtre du visualiseur de console virtuelle pour quitter la session correspondante.
L'état figure également dans l'écran OSCAR de la console virtuelle. Lorsque la console locale est activée, un état vert apparaît à côté du nom du serveur. Lorsqu'elle est désactivée, un point jaune indique qu'iDRAC a verrouillé la console locale. Pourquoi le bas de l'écran de la fenêtre de la console virtuelle ne s'affiche-t-il pas ? Vérifiez que la résolution du moniteur de la station de gestion est 1 280 x 1 024.
Vous configurez une session de console virtuelle depuis le système local et cette opération n'est pas prise en charge. Si une session de console virtuelle est en cours et qu'un utilisateur local accède au serveur géré, le premier utilisateur reçoit-il un message d'avertissement ? Non. Si un utilisateur local accède au système, vous contrôlez tous les deux le système.
Le BIOS Dell émule le pilote de la souris comme souris PS/2. Par nature, la souris PS/2 utilise une position relative pour le pointeur, ce qui génère des délais de synchronisation. L'iDRAC utilise un pilote de souris USB qui permet un positionnement absolu et permet de tracer plus précisément le pointeur de souris. Même si l'iDRAC envoie la position absolue de souris USB au BIOS Dell, l'émulation BIOS convertit la position en position relative et le comportement persiste.
Média virtuel Pourquoi la connexion du client Média Virtuel s'interrompt-elle parfois ? Si le délai d'attente du réseau expire, le micrologiciel d'iDRAC interrompt la connexion en déconnectant la liaison entre le serveur et le lecteur virtuel. Si vous changez le CD dans le système client, le nouveau CD peut disposer de la fonction de démarrage automatique. Dans ce cas, le micrologiciel peut expirer et la connexion est perdue si le système client prend trop de temps pour lire le CD.
Vous pouvez également démarrer avec un disque de démarrage Windows 98 et copier les fichiers système du disque de démarrage vers la clé USB. Par exemple, depuis l'invite DOS, entrez la commande suivante : sys a: x: /s , où x: est la clé USB qui doit être définie comme périphérique amorçable. Média Virtuel est connecté au lecteur de disquette distant, mais le lecteur de disquette virtuel/CD virtuel est introuvable sur un système exécutant le système d'exploitation Red Hat Enterprise Linux ou SUSE Linux.
Les mises à jour micrologicielles provoquent la réinitialisation d'iDRAC, suppriment la connexion distante et démontent les lecteurs virtuels. Les lecteurs réapparaissent à la fin de la réinitialisation d'iDRAC. Pourquoi tous les périphériques USB sont-ils déconnectés après la connexion d'un périphérique USB ? Les périphériques Média Virtuel et les périphériques vFlash sont connectés comme périphériques USB composites au BUS USB hôte et ils partagent un port USB.
Authentification SNMP Pourquoi le message « Accès distant : échec de l'authentification SNMP »' s'affiche-t-il ? Lors de la découverte, l'Assistant IT tente de vérifier les noms de communauté get et set du périphérique. L'Assistant IT contient le nom de communauté get = public et le nom de communauté set = private. Par défaut, le nom de communauté d'agent SNMP pour l'agent iDRAC est public.
• Cliquez sur Démarrer → Panneau de configuration → Programmes et fonctions. La version de l'iDRAC Service Module installé est répertoriée dans l’onglet Version . • Accédez à Poste de travail → Désinstaller ou modifier un programme. Quel est le niveau d'autorisation minimal requis pour installer l'iDRAC Service Module ? Pour installer l'iDRAC Service Module, vous devez disposer de privilèges Administrateur. Lors de l’installation de l'iDRAC Service Module version 2.
Lors de la désinstallation de l'iDRAC Service Module version 2.0 et versions antérieures à partir d’un serveur VMware ESXi, le commutateur virtuel est nommé comme vSwitchiDRACvusb et groupe de ports en tant que Réseau iDRAC dans le client vSphere.
RACADM Après avoir réinitialisé iDRAC (à l'aide de la commande racadm racreset), le message suivant s'affiche lors de l'exécution d'une commande. Qu'est-ce que cela indique ? ERROR: Unable to connect to RAC at specified IP address Le message indique que vous devez attendre qu'iDRAC termine la réinitialisation avant d'exécuter une autre commande. Lorsque vous exécutez des commandes et des sous-commandes RACADM, certaines erreurs ne sont pas effacées.
• iDRAC est réinitialisé. • Un nouveau certificat de serveur SSL est téléchargé. Pourquoi un message s'affiche lorsque j'essaie de supprimer une partition après l'avoir créée en utilisant l'interface locale RACADM ? Le message s'affiche, car l'opération de création de partition est en cours. Cependant, la partition est supprimée après un moment et un message indiquant que la partition est supprimée s'affiche.
Depuis l'interface Web d'iDRAC : accédez à Présentation → Serveur → Propriétés → Récapitulatif. La page Récapitulatif du système contient l'adresse IP de l'iDRAC. Dans l'interface locale RACADM : utilisez la commande racadm getsysinfo. Depuis l'écran LCD : sur le serveur physique, utilisez les boutons de navigation du panneau LCD pour afficher l'adresse IP iDRAC. Accédez àVue Configuration → Vue → Adresse IP iDRAC → IPv4 ou IPv6 → IP.
Lors de la tentative de démarrage du serveur géré, le voyant d'alimentation est vert, mais aucun POST ou aucune vidéo ne s'affiche. Ce problème apparaît pour l'une des raisons suivantes : • La mémoire n'est pas installée ou elle est inaccessible. • Le processeur n'est pas installé ou il est inaccessible. • La carte complémentaire vidéo n'est pas installée ou elle n'est pas connectée correctement.
Scénarios de cas d'utilisation 25 Cette section explique comment accéder à des sections spécifiques du guide pour exécuter des scénarios de cas d'utilisation types. Dépannage d'un système géré inaccessible Après avoir reçu des alertes d'OpenManage Essentials, de Dell Management Console ou d'un collecteur d'interruptions local, cinq serveurs dans un centre de données sont inaccessibles suite à un blocage du système d'exploitation ou du serveur.
Affichage des journaux Création du rapport de support technique Inventaire et surveillance des périphériques de stockage Utilisation de l'iDRAC Service Module Obtention des informations système et évaluation de l'intégrité du système Pour obtenir les informations système et évaluer l'intégrité du système : • Dans l'interface Web iDRAC, accédez à Présentation → Serveur → Récapitulatif du système pour afficher les informations du système et accéder aux liens de la page pour évaluer l'intégrité du système.
Interfaces de mise à niveau du micrologiciel iDRAC Utilisez les interfaces suivantes pour mettre à jour le micrologiciel iDRAC : • l'interface Web iDRAC • CLI RACADM (iDRAC et CMC) • Progiciel de mise à jour Dell (DUP - Dell Update Package) • Interface Web CMC • Services à distance Lifecycle Controller • Lifecycle Controller • Dell Remote Access Configuration Tool (DRACT) Exécution d'un arrêt normal Pour exécuter un arrêt normal, dans l'interface Web d'iDRAC, accédez aux emplacements suivants
3. Dans le menu Fichier, cliquez surMédia Virtuel → Lancer Média Virtuel. 4. Cliquez sur Ajouter une image et sélectionnez l'image qui se trouve sur le lecteur Flash USB. L'image est ajoutée à la liste des lecteurs disponibles. 5. Sélectionnez le lecteur à lui associer. L'image sur le lecteur Flash USB est associée au système géré.