Dell PowerEdge T620 Systems Owner's Manual Regulatory Model: E17S Series Regulatory Type: E17S001
注、小心和警告 注: “注”表示可以帮助您更好地使用计算机的重要信息。 小心: “小心”表示可能会计坏硬件或计致数据计失,并计明如何避免此计计计。 警告: “警告”表示可能会造成计计计失、人身计害甚至死亡。 版计所有 © 2014 Dell Inc. 保留所有计利。 本计品受美国、国计版计和知计计计法律保计。 Dell™ 和 Dell 徽计是 Dell Inc. 在美 国和 / 或其他管计区域的商计。所有此计提及的其他商计和计品名称可能是其各自所属公司的商计。 2014 - 07 Rev.
Contents 1 关于系计......................................................................................................................................9 前面板部件和指示灯—塔式模式......................................................................................................................... 9 前面板部件和指示灯—机架模式....................................................................................................................... 12 LCD 面板部件..............................................................................
Boot Manager(引计管理器)屏幕..............................................................................................................34 UEFI Boot Menu(UEFI 引计菜计)...............................................................................................................34 嵌入式系计管理....................................................................................................................................................34 iDRAC 计置公用程序.....................................................................
卸下计插拔硬计计计器................................................................................................................................. 54 安装计置计硬计计计器................................................................................................................................. 55 从硬计计计器托计中卸下硬计计计器.........................................................................................................55 将硬计计计器安装到硬计计计器托计中.....................................................................................
计计用功能..................................................................................................................................................... 78 卸下交流计源计计......................................................................................................................................... 79 安装交流计源计计......................................................................................................................................... 79 直流计源计计的布计计明.............................................
4 系计故障排除.........................................................................................................................119 安全第一 —— 计您和您的系计着想................................................................................................................119 系计启计失计故障排除......................................................................................................................................119 外部计接故障排除..........................................................................................
警告信息.............................................................................................................................................................. 155 计断程序信息......................................................................................................................................................155 警计信息.............................................................................................................................................................. 155 9 计得帮助...........
关于系统 1 前面板部件和指示灯—塔式模式 图 1: 前面板部件和指示灯—2.
图 2: 前面板部件和指示灯—3.
项目 指示灯、按钮或连接器 图标 说明 4 NMI 按钮 用于在运行某些操作系统时对软件和设备驱动程序错 误进行故障排除。可以用回形针的末端按压此按钮。 只有当合格的支持人员或操作系统说明文件指示可以 使用此按钮时才能使用它。 5 系统识别按钮 前面板和背面板上的识别按钮可用于查找机架中的特 定系统。当按下其中一个按钮时,系统前面板上的 LCD 面板和后面板上的系统状态指示灯将闪烁,直至 再次按下其中一个按钮为止。 按下可切换系统 ID 的开和关。 如果系统在 POST 过程中停止响应,按住系统 ID 按钮 五秒以上,可进入 BIOS 进程模式。 要重设 iDRAC(如果未在 F2 iDRAC 设置中禁用),请 按住该按钮超过 15 秒。 6 LCD 菜单按钮 用于导航控制面板 LCD 菜单。 7 信息标签 滑出式标签牌,用于根据您的需求记录系统信息,如 服务标签、NIC、MAC 地址等。 8 LCD 面板 显示系统 ID、状态信息和系统错误信息。LCD 将在系 统正常运行期间呈蓝色亮起。LCD 将在系统需要注意 时呈琥珀色亮起,并且 LCD 面板显示错误代码以及随 后的说
前面板部件和指示灯—机架模式 图 3: 前面板部件和指示灯—2.5 英寸硬盘驱动器机箱 注: 如果您的系统是机架,则在出厂之前预配置了机架吊耳,但没有系统支脚。 项目 指示灯、按钮或连接器 图标 说明 1、11 USB 连接器(2 个) 允许您将 USB 设备连接到系统。这些端口支持 USB 2.0。 2 光盘驱动器(可选) 一个可选的 SATA DVD-ROM 驱动器或 DVD+/-RW 驱动 器。 3 硬盘驱动器托架 3.5 英寸硬盘驱 动器系统 最多十二个 3.5 英寸可热插拔 硬盘驱动器。 多达四个 Dell PowerEdge Express Flash 设备 (PCIe SSD)。 2.5 英寸硬盘驱 动器系统 最多三十二个 2.
项目 指示灯、按钮或连接器 4 LCD 面板 图标 说明 显示系统 ID、状态信息和系统错误信息。LCD 将在系 统正常运行期间呈蓝色亮起。LCD 将在系统需要注意 时呈琥珀色亮起,并且 LCD 面板显示错误代码以及随 后的说明文字。 注: 如果系统已连接至电源并检测到错误,则无 论系统是否打开,LCD 都将呈琥珀色亮起。 5 LCD 菜单按钮 用于导航控制面板 LCD 菜单。 6 vFlash 介质卡插槽 允许您插入 vFlash 介质卡。 7 通电指示灯、电源按钮 通电指示灯在系统开机时亮起。电源按钮控制到系统 的电源设备输出。 注: 对于兼容 ACPI 的操作系统,使用电源按钮关 闭系统可以在系统电源关闭前执行正常有序的关 机操作。 8 NMI 按钮 用于在运行某些操作系统时对软件和设备驱动程序错 误进行故障排除。可以用回形针的末端按压此按钮。 只有当合格的支持人员或操作系统说明文件指示可以 使用此按钮时才能使用它。 9 系统识别按钮 前面板和背面板上的识别按钮可用于查找机架中的特 定系统。当按下其中一个按钮时,系统前面板上的 LCD 面板和后面板上的系统状态指示
图 4: LCD 面板部件 项目 按钮 说明 1 向左 使光标向后移动一步。 2 选择 选择由光标高亮度显示的菜单项。 3 向右 使光标向前移动一步。 在信息滚动过程中: • • • • 按一次可提高滚动速度 再按一次可停止滚动 再按一次可恢复默认的滚动速 度 再按一次将重复以上循环 主屏幕 主屏幕显示有关系统的用户可配置信息。当没有状态信息或错误时,此屏幕会在正常系统操作期间显示。当系 统处于待机模式时,如果没有错误信息,LCD 背景光将在不活动五分钟后关闭。请按三个导航按钮(选择、向 左或向右)中的一个来查看主屏幕。 要从另一个菜单导航到主屏幕,请继续选择向上箭头, 直到主屏幕图标 显示,然后选择主屏幕图标。 从主屏幕中按 Select(选择)按钮,进入主菜单。 Setup(设置)菜单 注: 在 Setup(设置)菜单中选择一个选项后,必须确认该选项,然后才能进行下一项操作。 选项 说明 iDRAC 选择 DHCP 或 Static IP(静态 IP)配置网络模式。如果选择 Static IP(静态 IP),可用 的字段将有 IP、Subnet (Sub)(子网
View(视图)菜单 注: 在 View(视图)菜单中选择一个选项后,必须确认该选项,然后才能进行下一项操作。 选项 说明 iDRAC IP 显示 iDRAC7 的 IPv4 或 IPv6 地址。地址包括 DNS(Primary(主)和 Secondary (次))、Gateway(网关)、IP 及 Subnet(子网)(IPv6 没有子网)。 MAC 显示 iDRAC、iSCSI 或 Network(网络)设备的 MAC 地址。 名称 显示系统的 Host(主机)名称、Model(型号)或 User String(用户字符串)。 编号 显示系统的 Asset tag(资产标签)或 Service tag(服务标签)。 电源 显示系统的功率输出,以 BTU/时或瓦特为单位。显示格式可以在 Setup(设置)菜单的 Set home(设置主屏幕)子菜单中配置。 温度: 显示系统的温度输出,以摄氏或华氏为单位。显示格式可以在 Setup(设置)菜单的 Set home(设置主屏幕)子菜单中配置。 硬盘驱动器指示灯显示方式 图 5: 硬盘驱动器指示灯 1.
驱动器状态指示灯 显示方式(仅适用 于 RAID) 状态 呈绿色闪烁,呈琥 珀色闪烁,然后熄 灭 预测的驱动器故障 每秒呈琥珀色闪烁 四次 驱动器故障 呈绿色缓慢闪烁 正在重建驱动器 呈绿色稳定亮起 驱动器联机 呈绿色闪烁三秒 钟,呈琥珀色闪烁 三秒钟,然后熄灭 六秒钟 已中止重建 16
背面板部件和指示灯 图 6: 背面板部件和指示灯 项目 指示灯、按钮或连接器 图标 说明 1 PCIe 扩充卡插槽(4 个) (处理器 1) 允许您连接最多两个 PCI Express 扩充卡和两个 PERC 卡。 2、3 以太网连接器 两个集成的 10/100/1000 Mbps NIC 连接器。 4 系统识别按钮 前面板和背面板上的识别按钮可用于查找机架中的特 定系统。当按下其中一个按钮时,系统前面板上的 17
项目 指示灯、按钮或连接器 图标 说明 LCD 面板和后面板上的系统状态指示灯将闪烁,直至 再次按下其中一个按钮为止。 按下可切换系统 ID 的开和关。 如果系统在 POST 过程中停止响应,按住系统 ID 按钮 五秒以上,可进入 BIOS Progress(BIOS 进程)模 式。 要重设 iDRAC(如果在 F2 iDRAC 设置中未禁用),则 按住 15 秒以上。 5 系统识别连接器 可让您通过可选的电缆管理臂连接可选的系统状态指 示灯部件。 6 iDRAC Enterprise 端口 专用管理端口。 注: 仅在系统上安装了 iDRAC Enterprise 许可证时 才可使用此端口。 7 电源设备 (PSU1) 495 W、750 W 或 1100 W 交流 或 1100 W 直流 8 USB 连接器(6 个) 允许您将 USB 设备连接到系统。这些端口支持 USB 2.
指示灯 指示灯代码 链路和活动指示灯 熄灭 NIC 未连接至网络。 链路指示灯呈绿色 亮起 NIC 以其最高端口速度(1 Gbps 或 10 Gbps)连接到有效的网络。 链接指示灯呈琥珀 色亮起 NIC 以低于其最高端口速度的速度连接到有效的网络。 活动指示灯呈绿色 闪烁 正在发送或接收网络数据。 电源指示灯代码 每个交流电源设备都有照亮的透明手柄,每个直流电源设备都有用作指示灯的 LED,以显示是否存在电源或是 否出现电源故障。 图 8: 交流电源设备状态指示灯 1. 交流电源设备状态指示灯/手柄 图 9: 直流电源设备状态指示灯 1.
电源指示灯显示方 式 状态 不亮 未连接电源。 绿色 手柄/LED 指示灯呈绿色亮起表示电源设备连接到有效的电源并且可以正常运行。 呈琥珀色闪烁 表示电源设备出现问题。 小心: 在纠正电源设备不匹配情况时,请仅更换指示灯闪烁的电源设备。更换另外 的电源设备以构成匹配的电源设备对将导致错误状况并且系统会出现意外关机。 要从高输出配置更改为低输出配置或反之,您必须关闭系统电源。 小心: 交流电源设备支持 220 V 和 110 V 输入电压,钛电源设备例外,其仅支持 220 V 输入电压,当两个相同的电源设备接收不同的输入电压时,它们可以输出不同功 率,由此触发不匹配情况。 小心: 如果使用两个电源设备,它们必须是相同的类型并且具有相同的最大输出功 率。 小心: 不支持配合使用交流和直流电源设备,并且这种混合会触发不匹配情况。 绿色闪烁 在热添加电源设备时,这表示电源设备与其它电源设备(在效率、功能组、运行状况和 支持的电压方面)不匹配。请使用与其它已安装电源设备容量匹配的电源设备来更换指 示灯闪烁的电源设备。 可能需要的其他信息 警告: 请参阅系统随附的安全和管制信息。保修信息可能包含在此说
使用系统设置程序和引导管理器 2 借助系统设置程序可以管理系统硬件和指定 BIOS 级选项。 在启动期间可以使用下列击键访问系统功能: 击键 说明 进入系统设置程序。 进入将打开 Dell Lifecycle Controller 2 (LC2) 的系统服 务。Dell LC2 使用图形用户界面支持系统管理功能, 如操作系统部署、硬件诊断、平台更新以及平台配 置。准确的 LC2 功能组由购买的 iDRAC 许可证决定。 有关详情,请参阅 Dell LC2 说明文件。 进入 BIOS 引导管理器或统一可扩展固件接口 (UEFI) 引 导管理器,具体视系统的引导配置而定。 。 启动预引导执行环境 (PXE) 引导。 通过系统设置程序,您可以: • 在添加或删除硬件后更改 NVRAM 设置 • 查看系统硬件配置 • 启用或禁用集成设备 • 设置性能和电源管理阈值 • 管理系统安全 可使用以下工具访问系统设置程序: • 标准图形浏览器,默认启用 • 文本浏览器,使用 Console Redirection(控制台重定向)启
统引导为同一引导模式(BIOS 或 UEFI)以访问安装的操作系统。试图从其它引导模式引导操作系统将导致系 统在启动时挂起。 注: 操作系统必须与 UEFI 兼容才能从 UEFI 引导模式安装。DOS 和 32 位操作系统不支持 UEFI,只能通过 BIOS 引导模式进行安装。 注: 有关支持的操作系统的最新信息,请访问 dell.com/ossupport。 进入系统设置 1. 打开或重新启动系统。 2.
菜单项 说明 System BIOS(系统 BIOS) 此选项用于查看和配置 BIOS 设置。 iDRAC Settings (iDRAC 设置) 此选项用于查看和配置 iDRAC 设置。 Device Settings(设 备设置) 此选项用于查看和配置设备设置。 System BIOS(系统 BIOS)屏幕 注: 系统设置程序的选项会基于系统配置发生变化。 注: 在以下几节中,系统设置程序的默认设置将在各自选项下列出(如果有)。 菜单项 说明 System Information (系统信息) 显示有关系统的信息,如系统型号名称、BIOS 版本、服务标签等。 Memory Settings (内存设置) 显示与所安装内存有关的信息和选项。 Processor Settings (处理器设置) 显示与处理器有关的信息和选项,如速度、高速缓存大小等。 SATA Settings (SATA 设置) 显示各选项以启用或禁用集成的 SATA 控制器和端口。 Boot Settings(引导 设置) 显示各选项以指定引导模式(BIOS 或 UEFI)。可让您修改 UEFI 和
菜单项 说明 System BIOS Version 显示系统上安装的 BIOS 版本。 (系统 BIOS 版本) System Service Tag (系统服务标签) 显示系统服务标签。 System Manufacturer 显示系统制造商的名称。 (系统制造商) System Manufacturer 显示系统制造商的联系信息。 Contact Information (系统制造商联系 信息) Memory Settings(内存设置)屏幕 菜单项 说明 System Memory Size (系统内存大小) 显示系统中安装的内存容量。 系统内存类型 显示系统中安装的内存类型。 显示系统内存速度。 System Memory Speed(系统内存速 度) 系统内存电压 显示系统内存电压。 Video Memory(视 频内存) 显示视频内存容量。 系统内存测试 指定系统内存检测是否在系统引导期间运行。选项包括 Enabled(启用)和 Disabled (禁用)。默认情况下,System Memory Testing(系统内存检测)选项设置为 Disabled (禁用)
Processor Settings(处理器设置)屏幕 菜单项 说明 逻辑处理器 允许您启用或禁用逻辑处理器并显示逻辑处理器数目。如果 Logical Processor(逻辑处 理器)选项设置为 Enabled(启用),BIOS 将显示所有逻辑处理器。如果此选项设置为 Disabled(禁用),则 BIOS 对每个核心仅显示一个逻辑处理器。默认情况下,Logical Processor(逻辑处理器)选项设置为 Enabled(启用)。 QPI 速率 允许您设置 QuickPath Interconnect(QuickPath 互联)数据速率设置。默认情况下,QPI Speed(QPI 速率)选项设置为 Maximum data rate(最大数据速率)。 注: QPI Speed(QPI 速率)选项仅在同时安装两个处理器时才显示。 Alternate RTID (Requestor Transaction ID) Setting(备用 RTID [请求程序交易 ID] 设置) 允许您对远程插槽分配多个 RTID,以便改进插槽间的高速缓存性能,或使 NUMA 在正 常模式下操作。默认情况下,Al
菜单项 说明 系列-型号-步进编号 按照 Intel 的定义显示处理器的系列、型号和步进编号。 品牌 显示处理器报告的品牌名称。 2 级高速缓存 显示 L2 高速缓存总和。 3 级高速缓存 显示 L3 高速缓存总和。 核心数量 显示每个处理器的内核数。 SATA Settings(SATA 设置)屏幕 菜单项 说明 Embedded SATA(嵌 允许将嵌入式 SATA 设置为 Off(关)、ATA、AHCI 或 RAID 模式。默认情况下, 入式 SATA) Embedded SATA(嵌入式 SATA)选项设置为 AHCI。 Port E(端口 E) Auto(自动)启用连接至 SATA 端口 E 的设备的 BIOS 支持。Off(关闭)禁用设备的 BIOS 支持。默认情况下,Port E(端口 E)设置为 Auto(自动)。 Port F(端口 F) Auto(自动)启用连接至 SATA 端口 F 的设备的 BIOS 支持。Off(关闭)禁用设备的 BIOS 支持。默认情况下,Port F(端口 F)设置为 Auto(自动)。 Boot Settings(引导设置)屏幕
Integrated Devices(集成设备)屏幕 菜单项 说明 Integrated RAID Controller(集成 RAID 控制器) 允许您启用或禁用集成 RAID 控制器。默认情况下,Integrated RAID Controller(集成 RAID 控制器)选项设置为 Enabled(启用)。 User Accessible USB 允许您启用或禁用用户可访问的 USB 端口。选择 Only Back Ports On(仅启用后面的端 Ports(用户可访问 口)可禁用前面的 USB 端口,选择 All Ports Off(关闭所有端口)将禁用前面和后面的 USB 端口) USB 端口。默认情况下,User Accessible USB Ports(用户可访问的 USB 端口)选项设 置为 All Ports On(打开所有端口)。 Internal USB Port (内部 USB 端口) 允许您启用或禁用内部 USB 端口。默认情况下,Internal USB Port(内部 USB 端口)选 项设置为 On(开)。 Internal SD Card Port 启用或禁用系
Serial Communications(串行通信)屏幕 菜单项 说明 Serial Communication 可让您在 BIOS 中选择串行通信设备(串行设备 1 和串行设备 2)。也可以启用 BIOS 控 (串行通信) 制台重定向,并可指定使用的端口地址。默认情况下,Serial Communication(串行通 信)选项设置为 On without Console Redirection(开,未启用控制台重定向)。 Serial Port Address (串行端口地址) 允许您设置串行设备的端口地址。默认情况下,Serial Port Address(串行端口地址)选 项设置为 Serial Device 1=COM2, Serial Device 2=COM1(串行设备 1=COM2,串行设备 2=COM1)。 注: 只能将串行设备 2 用于 LAN 上串行 (SOL)。要使用通过 SOL 的控制台重定向, 请为控制台重定向和串行设备配置相同的端口地址。 External Serial Connector(外部串 行连接器) 可让您将外部串行连接器与串行设备 1、串行设备 2 或远程
菜单项 说明 Turbo Boost 允许您启用或禁用处理器在 turbo boost 模式下运行。默认情况下,Turbo Boost 选项设 置为 Enabled(启用)。 C1E 允许您在处理器处于闲置状态时启用或禁用处理器切换至最低性能状态。默认情况下, C1E 选项设置为 Enabled(启用)。 C 状态 允许您启用或禁用处理器在所有可用电源状态下运行。默认情况下,C States(C 状 态)选项设置为 Enabled(启用)。 Monitor/Mwait 允许您启用处理器中的 Monitor/Mwait 指令。默认情况下,Monitor/Mwait 选项设置为已 为所有的系统配置文件 Enabled(启用),Custom(自定义)除外。 注: 仅当 C States(C 状态)选项在 Custom(自定义)模式下禁用时,才能禁用此 选项。 注: 当 C States(C 状态)在 Custom(自定义)模式下启用时,更改 Monitor/Mwait (显示器/Mwait)设置不会影响系统功率/性能。 内存轮巡检查 允许您设置内存轮巡检查频率。默认情况下,Memory Pat
菜单项 说明 TPM Status(TPM 状 显示 TPM 状态。 态) TPM Clear(TPM 清 除) 小心: 清除 TPM 会导致 TPM 中的所有密钥丢失。丢失 TPM 密钥可能对引导至操作 系统产生影响。 允许您清除 TPM 的所有内容。默认情况下,TPM Clear(TPM 清除)选项设置为 No (无)。 Intel TXT 允许您启用或禁用 Intel Trusted Execution Technology(Intel 受信任的执行技术)。要启 用 Intel TXT,必须启用 Virtualization Technology(虚拟化技术),并且必须启用 TPM Security(TPM 安全保护)的 Pre-boot measurements(预引导测量)。默认情况下, Intel TXT 选项设置为 Off(关闭)。 BIOS Update Control (BIOS 更新控制) 允许您使用基于 DOS 或 UEFI shell 的 快擦写公用程序更新 BIOS。对于不需要本地 BIOS 更新的环境,建议将此字段设置为 Disabled(禁用)。默认情况下,BIOS
菜单项 说明 F1/F2 Prompt on Error 允许您启用或禁用发生错误时 F1/F2 提示。默认情况下,F1/F2 Prompt on Error(发生错 (发生错误时 F1/F2 误时 F1/F2 提示)设置为 Enabled(启用)。 提示) 系统内特性 此字段用于启用或禁用 In-System Characterization(系统内特性)。默认情况下,InSystem Characterization(系统内特性)设置为 Enabled(启用)。 系统密码和设置密码功能 可创建系统密码和设置密码来保护您的系统安全。要启用系统密码和设置密码创建,密码跳线必须设置为启 用。有关密码跳线设置的详情,请参阅“系统板跳线设置”。 系统密码 必须输入此密码才能引导系统。 设置密码 必须输入此密码才能访问并更改系统的 BIOS 或 UEFI 设置。 小心: 密码功能为系统中的数据提供了基本的安全保护。 小心: 只要系统在运行且无人值守,任何人均可访问系统上存储的数据。 注: 您的系统出厂时已禁用系统密码和设置密码功能。 设定系统密码和/或设置密码 注: 密码跳线用于启用或禁用系统密码和
6. 重新输入先前输入的系统密码,然后单击 OK(确定)。 7. 选择 Setup Password(设置密码),输入系统密码,然后按 或 。 8. 将出现一则消息,提示您重新输入设置密码。 重新输入先前输入的设置密码,然后单击 OK(确定)。 9. 按 键可返回到系统 BIOS 屏幕。再按一次 键,将出现消息提示您保存更改。 注: 重新引导系统之后,密码保护才能生效。 删除或更改现有系统密码和/或设置密码 确保在尝试删除或更改现有系统密码和/或设置密码之前 Password(密码)跳线设置为 Enabled(已启用)并且 Password Status(密码状态)为 Unlocked(已解除锁定)。如果 Password Status(密码状态)为 Locked(已锁 定),则不能删除或更改现有系统密码和/或设置密码。 删除或更改现有系统和/或设置密码: 1. 要进入系统设置程序,请在开机或重新启动后立即按 。 2.
如果您尝试输入三次密码,但均不正确,系统会显示以下信息 Invalid Password! Number of unsuccessful password attempts: System Halted! Must power down.
Boot Manager(引导管理器)屏幕 菜单项 说明 Continue Normal Boot(持续正常引 导) 系统尝试从引导顺序中的第一项开始引导至设备。如果引导尝试失败,系统将继续从引 导顺序中的下一项进行引导,直到引导成功或者找不到引导选项为止。 BIOS Boot Menu (BIOS 引导菜单) 显示可用 BIOS 引导选项(标有星号)的列表。选择想要使用的引导选项并按 Enter 键。 UEFI Boot Menu (UEFI 引导菜单) 显示可用 UEFI 引导选项(标有星号)的列表。选择想要使用的引导选项并按 Enter 键。 UEFI Boot Menu(UEFI 引导菜单)可让您 Add Boot Option(添加引导选项)、Delete Boot Option(删除引导选项)或 Boot From File(从文件引导)。 Driver Health Menu (驱动程序运行状 况菜单) 显示系统上安装的驱动程序列表及其运行状况。 Launch System Setup 允许您访问系统设置程序。 (启动系统设置) System Utilities(系 统公用程
iDRAC 设置公用程序 iDRAC 设置公用程序是使用 UEFI 设置和配置 iDRAC 参数的接口。可使用 iDRAC 设置公用程序启用或禁用各种 iDRAC 参数。 注: 访问 iDRAC 设置公用程序上的某些功能需要升级 iDRAC7 Enterprise 许可证。 有关使用 iDRAC 的更多信息,请参阅 dell.com/support/manuals 上软件 → 系统管理 → Dell Remote Access Controllers 下的 iDRAC7 用户指南。 进入 iDRAC 设置公用程序 1. 开启或重新启动受管系统。 2. 开机自测 (POST) 期间按 。 3. 在 System Setup Main Menu(系统设置主菜单)页面,单击 iDRAC Settings(iDRAC 设置)。 将显示 iDRAC Settings(iDRAC 设置)屏幕。 更改热设置 iDRAC Settings(iDRAC 设置)公用程序可让您选择和自定义您系统的热控制设置。 1. 进入 iDRAC 设置公用程序 2.
安装系统组件 建议工具 要执行本节中的步骤,可能需要使用以下工具: • 系统键锁的钥匙 • 2 号梅花槽螺丝刀 • T10 和 T15 Torx 螺丝刀 • 接地腕带 制作直流电源设备 (PSU) 的电缆(如果可用)需要以下工具: • AMP 90871-1 手动压接工具或同类产品 • 可以除去尺寸为 10 AWG 的绝缘的实芯或绞合铜电线的绝缘层的剥线钳 注: 使用 alpha 电线部件号 3080 或同类产品(65/30 绞合)。 前挡板(可选) 安装前挡板 1. 找到前挡板内部的钥匙。 2. 从前挡板内部卸下挡板钥匙。 3. 将挡板卡舌插入机箱中的挡板卡舌插槽。 4. 将挡板顶端按入机箱,直至挡板锁定到位。 5. 在钥匙锁中插入挡板钥匙。 6.
图 10: 安装和卸下前挡板 卸下前挡板 1. 在钥匙锁中插入挡板钥匙。 2. 使用挡板钥匙持续按压钥匙锁,旋转钥匙锁至解除锁定位置。 3. 按下挡板顶部的释放闩锁。 4. 旋转挡板的顶端,使其远离系统。 5. 松开机箱前面的插槽中的挡板卡舌。 系统支撑点—塔式模式 该系统支撑点为处于塔式模式下的系统提供稳定性。 Removing The System Feet 1. Rotate the system feet inward. 2. Lay the system on its side on a flat, stable surface. 3. Remove the screws securing the system feet to the base of the tower.
Figure 11. Removing and Installing the System Feet 1. base of the tower 3. screws (4) 2. system feet (4) 安装系统支撑点 1. 将系统一侧放置在平稳的表面上。 2. 使用螺钉将系统支撑点固定到塔式系统基座上。 3. 将系统垂直放置在平稳的表面上,并使系统支撑点转向外侧。 滚轮部件(可选)—塔式模式 该滚轮部件为处于塔式模式的系统提供移动性。 该滚轮部件由以下各项组成: • 滚轮部件装置(前面和后面) • 用于滚轮部件装置的两颗螺钉 安装滚轮部件 1. 如果适用,向内旋转系统支脚。 2. 使系统基座远离台面边缘扩展,并将系统放置在平稳的表面上。 3. 如果适用,请卸下系统支脚。 4.
5. 稍微偏移后滚轮部件至系统背面,并使用一个螺钉将该装置固定到位。 6. 将前滚轮部件上的两个固定挂钩对齐机箱基座上的两个插槽,并将挂钩插入插槽中。 7. 稍微偏移前滚轮部件至正面,并使用一个螺钉将该装置固定到位。 8. 将系统垂直放置在平稳的表面上。 卸下滚轮部件 1. 使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面上。 2. 卸下将前滚轮部件装置固定到机箱基座的螺钉。 3. 稍微偏移前滚轮部件装置至系统背面,以释放固定挂钩,并拉出前滚轮部件装置。 4. 卸下将后滚轮部件装置固定到机箱基座的螺钉。 5. 稍微偏移后滚轮部件装置至系统背面,以释放固定挂钩,并拉出后滚轮部件装置。 6. 如果您不要装回滚轮部件,请安装系统支脚。 7. 如果适用,将系统放置在平稳的表面上,并向外旋转系统支脚。 图 12: 卸下和安装滚轮部件 1. 塔式系统基座上的插槽(4 颗) 3. 螺钉(2 颗) 2.
打开与合上系统护盖 警告: 每当您需要抬起系统时,请让他人协助您。为避免伤害,请勿试图一个人抬起系统。 警告: 系统处于运行状态时打开或卸下系统护盖会使您有触电的风险。 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 不要操作没有护盖的系统超过五分钟。 打开系统护盖 小心: 要为独立的塔式系统提供稳固的基础,需要安装支脚。如果未安装支脚,可能存在导致系统倾翻的 危险,从而可能造成人身伤害或损坏系统。 注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 1. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 2. 将闩锁释放锁逆时针转至解除锁定位置。 3. 按下护盖释放闩锁,将护盖的闩锁端旋离系统。 4. 抓住护盖两侧,小心地从系统上提起护盖,使其离开系统。 图 13: 打开与合上系统护盖 40 1. 系统 2. 系统侧护盖 3. 系统护盖释放闩锁 4.
合上系统护盖 1. 将与系统护盖释放闩锁相对的底边插入系统机箱的插槽中。 2. 将系统护盖向下放置到机箱上。 3. 将系统护盖的闩锁端按入机箱,直至闩锁锁定到位为止。 4. 将护盖闩锁的释放锁沿顺时针方向旋转至锁定位置。 5. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 系统内部 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 热插拔组件标记为橙色,组件上的触点标记为蓝色。 图 14: 系统内部 1. 冷却风扇部件(可选) 2. PCIe 卡固定器 3. 冷却导流罩 4. 冷却风扇(2 个) 5. 散热器(2 个) 6. PCIe 卡固定器 7. 系统支脚(4 个) 8. DIMM(24 个) 9.
挡板挡片 卸下挡板挡片 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 打开系统护盖。 3. 确认要卸下的挡板挡片,推动金属卡舌从机箱插槽中取出挡片。 注: 在塔式模式下,可在打开的系统右侧看到金属卡舌。 4. 从机箱中拉出挡板挡片。 图 15: 卸下和安装挡板挡片 1. 挡板挡片 2.
注: 根据您系统的配置,您可能有 2.5 英寸或 3.5 英寸的挡板挡片。不同类型挡板挡片的安装和拆卸步骤相 同。 1. 将挡板挡片与机箱上相应的插槽对准。 2. 将挡板挡片插入机箱上的空闲插槽,直至挡板挡片上的金属卡舌卡入到位。 3. 合上系统护盖。 4. 请安装前挡板(如果适用)。 冷却导流罩 卸下冷却导流罩 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 绝对不要在冷却罩被移除的情况下操作系统。系统有可能会迅速过热,造成系统关闭和数据丢失。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 将系统侧面朝下放置。 3. 打开系统护盖。 4. 如果需要,卸下两个系统风扇。 5. 按压卡舌,按住冷却导流罩中心的触点。 6. 将导流罩从系统中提出。 图 16: 卸下和安装冷却导流罩 1. 冷却导流罩 2.
安装冷却导流罩 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 要将冷却导流罩正确安装在系统机箱内,请确保系统内的电缆沿着机箱壁布置,并使用电缆固定支架 固定。 1. 将冷却导流罩上的卡舌对准机箱上的固定插槽。 2. 将冷却导流罩向下放置到机箱中直至稳固就位。 3. 如果适用,将系统冷却风扇安装在冷却导流罩中。 4. 合上系统护盖。 5.
图 17: 内存插槽位置 内存通道按如下方式组织: 处理器 1 通道 0:插槽 A1、A5 和 A9 通道 1:插槽 A2、A6 和 A10 通道 2:插槽 A3、A7 和 A11 通道 3:插槽 A4、A8 和 A12 处理器 2 通道 0:插槽 B1、B5 和 B9 通道 1:插槽 B2、B6 和 B10 通道 2:插槽 B3、B7 和 B11 通道 3:插槽 B4、B8 和 B12 下表显示支持配置的内存数和操作频率。 DIMM 类型 填充的 DIMM 数/ 通道 操作频率 (MT/s) 1.5 V 最大 DIMM 列数/通道 1.
DIMM 类型 填充的 DIMM 数/ 通道 操作频率 (MT/s) 1.5 V RDIMM 1 1.
下面各节提供每个模式的其它插槽填充原则。 高级 ECC (Lockstep) 高级 ECC 模式将 SDDC 从基于 x4 DRAM 的 DIMM 扩展到 x4 和 x8 DRAM。这样可防止正常操作期间单个 DRAM 芯片故障。 内存安装原则: • 所有内存模块在大小、速度和技术上必须相同。 • 带有白色释放卡舌的内存插槽中安装的 DIMM 必须相同,类似规则适用于带黑色和绿色释放卡舌的插槽。 这可确保相同 DIMM 以匹配对安装 - 例如,A1 与 A2、A3 与 A4、A5 与 A6 等。 注: 不支持带镜像功能的高级 ECC。 内存优化(独立通道)模式 此模式仅针对使用 x4 设备宽度的内存模块支持 SDDC,不会产生任何特定插槽填充要求。 内存备用 注: 要使用内存备用,必须在系统设置程序中启用此功能。 在此模式下,每个通道的一列保留作为备用列。如果在列上检测到持久可纠正错误,将复制此列中的数据到备 用列,并禁用出现故障的列。 如果启用内存备用,对操作系统可用的系统内存将每个通道减少一列。例如,在具有 16 个 4 GB 双列 DIMM 的 双处理器配置中,可用系统内存为:3/4(列/
DIMM 大小 DIMM 数量 (以 GB 为单 位) 系统容量(以 GB 为单位) DIMM 列、组织和频率 DIMM 插槽数 1R,x8,1600 MT/s 4 2 2 1R,x8,1333 MT/s, 1R,x8,1600 MT/s A1、A3 8 2 4 1R,x8,1333 MT/s, 1R,x8,1600 MT/s A1、A2、A3、A4 12 2 6 1R,x8,1333 MT/s, 1R,x8,1600 MT/s A1、A2、A3、A4、A5、A6 16 2 8 1R,x8,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8 4 4 2R,x8,1333 MT/s, 2R,x8,1600 MT/s A1、A2、A3、A4 2 12 1R,x8,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A12 4 6 2R,x8,1333 MT/s, 2R,x8,1600 MT/s A1、A2、A3、A4、A5、A6 4 12 2R,x8,1333 MT/s A1、A
系统容量 DIMM 大小(以 DIMM 数量 (以 GB 为单 GB 为单位) 位) DIMM 列、组织和频率 DIMM 插槽数 B1、B2、B3、B4、B5、B6、B7、 B8 8 8 2R,x4,1333 MT/s, 2R,x4,1600 MT/s A1、A2、A3、A4 B1、B2、B3、B4 4 24 2R,x8,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A12 B1、B2、B3、B4、B5、B6、B7、 B8、B9、B10、B11、B12 8 12 2R,x4,1333 MT/s, 2R,x4,1600 MT/s A1、A2、A3、A4、A5、A6 B1、B2、B3、B4、B5、B6 8 16 2R,x4,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8 B1、B2、B3、B4、B5、B6、B7、 B8 16 8 2R,x4,1333 MT/s, 2R,x4,1600 MT/s A1、A2、A3、A4、B1、B2、B3、 B4 160 8 20 2R,x4,1333 MT/s
卸下内存模块 警告: 在系统关机后一段时间内,内存模块会很烫手。请让其冷却下来后再进行操作。仅抓住内存模块的 卡边缘,避免触到内存模块上的组件或金属触点。 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下冷却导流罩。 4. 找到相应的内存模块插槽。 小心: 仅抓住每个内存模块的两边,避免接触内存模块或黄金触点的中间。 5. 向下并向外按压插槽两端的弹出卡舌,直至内存模块从插槽中弹出。 图 18: 卸下和安装内存模块 1. 内存模块 3. 定位卡锁 2. 内存模块插槽弹出卡舌(2 个) 6. 安装冷却导流罩。 7. 合上系统护盖。 8.
小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 将系统侧面朝下放置。 3. 打开系统护盖。 4. 卸下冷却导流罩。 5. 找到内存模块插槽的位置。 6. 向下并向外按压插槽两端的弹出卡舌,直至内存模块从插槽中弹出。 小心: 仅抓住每个内存模块的两边,避免接触内存模块或黄金触点的中间。 7. 将内存模块的边缘连接器与内存模块插槽的定位卡锁对准,并将内存模块插入插槽。 注: 内存模块插槽有定位卡锁,使内存模块只能从一个方向安装到插槽中。 8. 9. 使用大拇指向下按压内存模块,直至插槽拉杆闩锁锁定到位。 如果内存模块已在插槽中正确就位,则内存模块插槽上的拉杆应与已安装内存模块的其它插槽上的拉杆对 准。 重复此过程的步骤 6 至步骤 9 以安装其余的内存模块。 10. 装回冷却导流罩。 11.
4. 按下释放闩锁,将可更换托架拉离机箱。 5. 合上系统护盖。 6. 请装回前挡板(如果适用)。 图 19: 卸下和安装可更换托架 1. 可更换托架 2. 释放闩锁 安装可更换托架 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将可更换托架对准机箱前部。 2. 将可更换托架插入机箱,直至卡舌卡入到位。 3. 合上系统护盖。 4.
卸除 2.5 英寸硬盘驱动器挡片 小心: 为了维持正常的系统冷却,所有闲置的硬盘驱动器插槽必须安装硬盘驱动器挡片。 1. 如果已安装前挡板,请将其卸下。 2. 按下释放卡舌并将硬盘驱动器挡片滑出,直到其脱离驱动器插槽。 图 20: 卸下和安装 2.5 英寸硬盘驱动器挡片 1. 硬盘驱动器挡片 2. 释放按钮 安装 2.5 英寸硬盘驱动器挡片 1. 如果已安装前挡板,请将其卸下。 2. 将硬盘驱动器挡片插入硬盘驱动器插槽,直到释放按钮卡入到位。 3. 请安装前挡板(如果适用)。 卸下 3.5 英寸硬盘驱动器挡片 小心: 为了维持正常的系统冷却,所有闲置的硬盘驱动器插槽必须安装驱动器挡片。 1. 如果已安装前挡板,请将其卸下。 2.
图 21: 卸下和安装 3.5 英寸硬盘驱动器挡片 1. 硬盘驱动器挡片 2. 释放按钮 安装 3.5 英寸硬盘驱动器挡片 1. 如果已安装前挡板,请将其卸下。 2. 将硬盘驱动器挡片插入硬盘驱动器插槽,直至释放按钮卡入到位。 3. 如果有,请安装前挡板。 卸下热插拔硬盘驱动器 小心: 为了防止数据丢失,请确保操作系统支持热交换驱动器安装。请参照操作系统随附的说明文件。 1. 2. 在管理软件中,准备要卸下的硬盘驱动器。等待硬盘驱动器托盘上的硬盘驱动器指示灯指示可以安全卸下 硬盘驱动器。有关详情,请参阅存储控制器的说明文件。 如果硬盘驱动器处于联机状态,则绿色的活动/故障指示灯将在驱动器关闭时闪烁。硬盘驱动器指示灯熄 灭时,才能卸下硬盘驱动器。 按下释放按钮以打开硬盘驱动器托盘释放手柄。 3. 向外滑动硬盘驱动器托盘,直至其脱离硬盘驱动器插槽。 小心: 为了维持正常的系统冷却,所有闲置的硬盘驱动器插槽必须安装硬盘驱动器挡片。 4.
图 22: 卸下和安装热插拔硬盘驱动器 1. 释放按钮 3. 硬盘驱动器托盘手柄 2. 硬盘驱动器 安装热置换硬盘驱动器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 只能使用经检测和认证可用于硬盘驱动器背板的硬盘驱动器。 小心: 不支持在相同的 RAID 卷中混合使用 SAS 和 SATA 硬盘驱动器。 小心: 安装硬盘驱动器时,确保相邻的硬盘驱动器已安全安装。插入硬盘驱动器托盘,尝试锁定已部分安 装托盘旁边的手柄可能损坏部分安装的托盘保护弹簧并使其无法使用。 小心: 为了防止数据丢失,请确保操作系统支持热交换驱动器安装。请参照操作系统随附的说明文件。 小心: 在安装了替换的热交换硬盘驱动器,并且系统开机之后,硬盘驱动器会自动开始重建。必须确保替 换的硬盘驱动器是空白的或包含您想覆盖的数据。替换的硬盘驱动器安装之后,上面的数据会立即丢 失。 1.
图 23: 在硬盘驱动器托盘中卸下和安装硬盘驱动器 1. 硬盘驱动器托盘 2. 硬盘驱动器 3. 螺钉(4 颗) 将硬盘驱动器安装到硬盘驱动器托盘中 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将硬盘驱动器插入硬盘驱动器托盘,此过程中,确保硬盘驱动器的连接器端朝后。 2. 将硬盘驱动器上的螺孔对准硬盘驱动器托盘后端的孔组。 正确对准后,硬盘驱动器的背面将与硬盘驱动器托盘的背面齐平。 装上螺钉以将硬盘驱动器固定到硬盘驱动器托盘中。 3.
卸下细长型光盘驱动器挡片 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 打开系统护盖。 3. 从系统内找到细长型光盘驱动器挡片的触点。 4. 按下锁,将细长型光盘驱动器挡片从机箱中拉出。 5. 合上系统护盖。 6. 请安装前挡板(如果适用)。 图 24: 卸下和安装细长型光盘驱动器挡片 1. 细长型光盘驱动器挡片 2. 光盘驱动器挡片锁 安装细长型光盘驱动器挡片 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将细长型光盘驱动器挡片与细长型光盘驱动器托架对齐。 2. 将细长型光盘驱动器挡片滑入光盘驱动器托架,直至锁卡入到位。 3.
• 最多一个 SATA 半高 DVD-ROM 或 DVD R/W 驱动器加一个内部 RD1000 驱动器加一个 SAS 接口磁带驱动器 配备多达 12 个硬盘驱动器的系统支持: • 最多一个 SATA 半高 DVD-ROM 或 DVD R/W 驱动器或 • 最多一个内部 RD1000 驱动器或 • 最多一个 SAS 接口磁带驱动器 配备多达 32 个硬盘驱动器的系统支持一个细长型光盘驱动器。不支持磁带驱动器。 卸下光盘驱动器或磁带驱动器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 注: 对于安装了滚轮部件的系统,请确保使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面 上。 打开系统护盖。 4. 5.
图 25: 卸下和安装光盘驱动器或磁带驱动器 1. 光盘驱动器/磁带驱动器 3. 释放闩锁 2.
图 26: 布线—光盘驱动器和磁带驱动器 60 1. 内部磁带适配器 2. 内部磁带适配器上的小型 SAS/SATA 连接 器 3. 系统板上的 ODD2/TBU 连接器 4. 系统板上的 ODD1/TBU 连接器 5. x16 背板上的电源连接器 6. SAS 磁带驱动器数据/电源连接器 7. 光盘驱动器 2 电源连接器 8. 光盘驱动器 2 数据连接器 9. 光盘驱动器 1 电源连接器 10.
安装光盘驱动器或磁带驱动器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 打开驱动器的包装并准备安装。 有关说明,请参阅随驱动器附带的说明文件。 如果您要安装 SAS 磁带驱动器,则必须首先安装好内部磁带适配器。请参阅“安装扩充卡”。 2. 如果已安装前挡板,请将其卸下。 3. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 4. 如果适用,向内旋转系统支脚,并将系统一侧放置在平稳的表面上。 5. 注: 对于安装了滚轮部件的系统,请确保使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面 上。 打开系统护盖。 6. 如果适用,请卸下旧驱动器或驱动器挡片。 7. 将驱动器对准驱动器托架。 8. 将驱动器滑入插槽,直至闩锁卡入到位。 9. 将电源电缆和数据电缆连接到驱动器的背面。 10.
注: 从冷却风扇部件上和从冷却导流罩上卸下单个风扇的过程是相同的。 1. 打开系统护盖。 2. 按下风扇释放卡舌,将冷却风扇从冷却风扇部件中取出。 图 27: 从冷却风扇部件中卸下和安装冷却风扇 1. 冷却风扇(2 个) 2. 冷却风扇部件 安装冷却风扇 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 将单个冷却风扇安装到冷却导流罩中的过程是相似的。 注: 在冷却风扇部件中和冷却导流罩中安装单个风扇的过程也是相同的。 1. 将冷却风扇基座上的插头与系统板上的连接器对齐。 2. 将冷却风扇滑入固定插槽,直至卡舌卡入到位。 3.
卸下冷却风扇部件(可选) 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 向上旋转蓝色释放拉杆,从机箱解除对冷却风扇部件的锁定。 4. 从机箱中取出冷却风扇部件。 图 28: 卸下和装回冷却风扇部件 1. 2. 3. 4.
注: 确保在安装冷却风扇部件前已正确安装电缆并使用电缆固定支架进行固定。错误安装电缆可能会损坏 电缆。 1. 将冷却风扇部件插槽与机箱侧壁上的导向销对齐。 2. 将冷却风扇部件滑入机箱。 3. 向下旋转蓝色释放拉杆,将冷却风扇部件卡入机箱。 4. 合上系统护盖。 5.
PCIe 卡袋 卸下 PCIe 卡袋 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 按下卡舌,从机箱中推拉 PCIe 卡袋。 4. 从机箱中取出 PCIe 卡袋。 图 30: 卸下和安装 PCIe 卡袋 1. 卡舌 2. PCIe 卡袋 安装 PCIe 卡袋 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与其电源插座的连接。 2. 打开系统护盖。 3. 将 PCIe 卡袋与机箱上的凸点对齐,将其往下按直至稳固就位。 4. 合上系统护盖。 5.
GPU 卡固定器(可选) 卸下 GPU 卡固定器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 如果适用,向内旋转系统支脚,并将系统一侧放置在平稳的表面上。 3. 注: 对于安装了滚轮部件的系统,请确保使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面 上。 打开系统护盖。 4. 卸下冷却导流罩。 5. 按下释放卡舌,从机箱中拉出 GPU 卡固定器。 6. 装回冷却导流罩。 7. 合上系统护盖。 8. 如果适用,将系统垂直放置在平稳的表面上,并向外旋转系统支脚。 9. 如果适用,将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 66 1. 释放卡舌 3. 导梢 2.
安装 GPU 卡固定器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 如果适用,向内旋转系统支脚,并将系统一侧放置在平稳的表面上。 3. 注: 对于安装了滚轮部件的系统,请确保使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面 上。 打开系统护盖。 4. 将 GPU 卡固定器对准机箱上的插槽和导梢,将其向下推直至就位。 5. 合上系统护盖。 6. 如果适用,将系统垂直放置在平稳的表面上,并向外旋转系统支脚。 7. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 扩充卡 扩展卡安装原则 表.
插卡优先级 插卡类型 插槽优先级 最大允许量 3 外部 RAID 4、5、6、2、7 5 4 内部 RAID 4、2、1、3 1 5 聚合网络适配器 (CNA) 4、5、6、2、7、1 6 6 10 Gb NIC 4、5、6、2、7、1 6 7 FC4/8 HBA 4、5、6、2、7、1、3 7 8 1 Gb NIC 4、5、6、2、7、1、3 7 9 非 RAID 1、4、5、6、2、7 6 10 内部磁带适配器 1、4、2 3 11 HIC 4、5、7、2 4 GPU 卡安装原则 安装 GPU 卡时请遵循以下原则: • 确保 GPU 启用套件就绪。 • 确保所有 GPU 卡的类型或型号相同。 • 每个 GPU 卡最多支持 6 GB 专用 GDDR5 内存。 • 单处理器配置在插槽 2 和 4 中仅支持最多两个双幅或单幅卡。 • 双处理器配置在插槽 2、4、5 和 7 中支持四个双幅或单幅卡。 • 必须安装两个处理器才能使用插槽 5 和 7。 • 单处理器配置上的两个双幅 GPU 卡和双处理器配置上的四
4. 卸下 PCIe 卡袋。 5. 如果有,从 GPU 卡上拔下 PERC 卡的数据电缆或/和电源电缆。 6. 打开 PCIe 卡闩锁。 7. 8. 握住插卡的边缘,小心地向上拉出插卡以将其从卡连接器中卸下,然后继续向上拉动插卡将其拉出插卡导 向器。 关闭 PCIe 卡闩锁。 9. 装回 PCIe 卡袋。 10. 合上系统护盖。 11. 将系统直立放置。 12. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 图 31: 卸下和安装扩充卡 1. 2. 3. PCIe 卡闩锁 PCIe 卡连接器 PCIe 卡 安装扩充卡 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 2. 打开扩充卡的包装并准备安装。 有关说明,请参阅扩充卡附带的说明文件。 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4.
7. 如果要安装新插卡,请卸下填充挡片。 注: 请保管好此挡片,以便卸下扩充卡后使用。您必须在闲置的扩充卡插槽中安装填充挡片,以维护 FCC 对本系统的认证。挡片还可以防止灰尘进入系统,并有助于系统内部的正常冷却和通风。 8. 握住卡的边缘,调整卡的位置,从而使卡式边缘连接器与 PCIe 卡连接器对准。 9. 将卡式边缘连接器稳固地插入 PCIe 卡连接器,直至插卡完全就位。 10. 关闭 PCIe 卡闩锁。 11. 将所有电缆连接至 PCIe 卡(如果适用)。 12. 装回 PCIe 卡袋。 13. 合上系统护盖。 14. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 15. 按照插卡说明文件中的说明,安装插卡所需的任何设备驱动程序。 卸下 GPU 卡 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2.
图 32: 卸下和安装 GPU 卡 1. 2. 3. 4. 5. 6. GPU 卡 SLI 数据连接器 GPU 卡电源连接器 GPU 卡电源连接器 x16 连接器 PCIe 卡闩锁(2 个) 安装 GPU 卡 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 确保 GPU 卡安装在 x16 插槽中。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 将系统侧面朝下放置。 3. 打开系统护盖。 4. 卸下 PCIe 卡固定器。 5. 打开两个 PCIe 卡闩锁。 6. 卸下填充挡片。 7. 找到系统板上的 x16 插槽。 8. 将 GPU 卡插入插槽。 9. 将电缆连接至 GPU 卡。 10. 关闭两个 PCIe 卡闩锁。 11.
12. 合上系统护盖。 13. 将系统直立放置。 14. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 SD vFlash 卡 vFlash SD 卡是一种安全数字 (SD) 卡,可插入系统中的 vFlash SD 卡插槽。它提供持久按需本地存储和自定义部 署环境,可自动进行服务器配置、脚本和成像。它模拟 USB 设备。有关详情,请参阅 support.dell.com/manuals 上的《iDRAC7 用户指南》。 装回 SD vFlash 卡 1. 找到系统上的 vFlash 介质插槽。有关详情,请参阅“关于系统”。 2. 要卸下 vFlash 介质卡,向内推动卡使其松脱,然后从卡插槽中取出卡。 图 33: 卸下和安装 SD vFlash 卡 1. 3. vFlash 介质卡 2. vFlash 介质卡插槽 要安装 vFlash 介质卡,将带标签的一面朝上,将 SD 卡的触针一端插入模块上的卡插槽中。 注: 为确保正确插入卡,插槽设置了键锁。 4.
5. 推拉双 SD 模块,将其从系统板上卸下。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 图 34: 卸下和安装内部双 SD 模块 1. SD 卡连接器 3. SD 卡 2. 内部双 SD 卡模块 安装内部双 SD 模块 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 在系统板上找到 IDSDM 连接器。 4. 将系统板上的连接器和双 SD 模块对齐。 5. 推拉双 SD 模块,直至其在系统板上稳固就位。 6. 合上系统护盖。 7.
卸下内部 SD 卡 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 找到内部双 SD 模块上的 SD 卡插槽,向内按压插卡,使其脱离插槽,然后卸下插卡。 4. 合上系统护盖。 5. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 安装内部 SD 卡 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 要在系统中使用 SD 卡,请确保已在系统设置程序中启用内部 SD 卡端口。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3.
4. 卸下冷却导流罩。 警告: 在系统关机后一定时间内,散热器和处理器都会很烫手。请让它们冷却下来后再进行操作。 5. 小心: 除非要移除处理器,否则绝对不要将散热器从处理器上移开。散热器是维持正常散热状态所必 不可少的。 使用 2 号梅花槽螺丝刀,拧下将散热器固定到系统板的第一个螺钉。 6. 等待 30 秒钟,以使散热器与处理器分开,并与第一个螺钉成对角线拧下螺钉。 7. 对剩余两个螺钉重复此过程。 8. 卸下散热器。 图 35: 卸下和安装处理器 1. 散热器 2. 固定螺钉(4 个) 3. 处理器 4. 插槽(4 个) 小心: 留在插槽中的处理器承受着强大的压力。请注意,如果抓得不紧,释放拉杆可能会突然弹起。 9. 将您的大拇指稳固放在解除锁定图标旁边的处理器底座释放拉杆上, 锁定位置释放拉杆。 10.
图 36: 处理器护盖打开与合上拉杆的顺序 1. 插槽释放拉杆 2. 关闭第一个图标 3. 处理器 4. 插槽释放拉杆 5. 打开第一个图标 11. 抓住处理器护盖上的卡舌,向上转动并将其拉出。 12.
图 37: 卸下和安装处理器 1. 关闭第一个插槽释放拉杆 2. 处理器的 1 号插针边角 3. 处理器 4. 打开第一个插槽释放拉杆 5. 插槽 6. 指南 7. 插槽 8. 金色三角形 安装处理器 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 如果要安装单处理器,则必须在插座 CPU1 中安装。 1. 在升级系统之前,请先从 support.dell.com 下载最新的系统 BIOS 版本,按照下载的压缩文件中的说明在系 统上安装更新。 注: 您可以使用 Lifecycle Controller(生命周期控制器)更新系统 BIOS。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 与电源断开连接时,请按住电源按钮 3 秒钟以便完全释放系统残留的电量,然后再卸下护盖。 4. 打开系统护盖。 5. 卸下冷却导流罩。 6.
9. 同样,从锁定位置释放先关闭图标旁边的插槽释放拉杆 将拉杆向上旋转 90 度。 10. 抓住处理器护盖上接近锁定符号的卡舌,向上转动并将其拉出。 11. 将处理器安装到插槽中: 小心: 处理器放置错位将永久破坏系统面板或者处理器本身。请留意不要弯曲底座内的管脚。 a. 通过找到处理器一角上的金色小三角形,可以识别处理器的 1 号插针边角。将此边角放在 ZIF 插槽的同 一边角中(通过系统板上相应的三角形识别)。 b. 将处理器的 1 号插针边角对准系统板的 1 号插针边角。 c. 将处理器轻轻地置入插槽中。 小心: 由于系统使用 ZIF 处理器插槽,因此请勿用力。处理器正确定位后,略微按压即可向下进 入插槽中。 d. 合上处理器护盖。 e. 旋转解除锁定符号旁边的插槽释放拉杆,直至其锁定到位。 f. 同样,将锁定符号旁边的插槽释放拉杆旋转至锁定位置。 小心: 使用过多导热膏会导致多余的油膏溢出,接触并污染处理器底座。 12. 如适用,安装散热器: a. 打开随处理器套件附带的油脂涂抹器,将涂抹器中的所有导热油脂涂到新处理器上面的中间。 b. 将散热器放置在处理器上。 c.
如果两个电源设备都处于活动状态比冗余电源设备处于休眠状态的效率更高,则活动电源设备也可激活处于休 眠状态的电源设备。如果活动电源设备上的负载超过 50%,则电源设备默认为唤醒两个电源设备,如果负载低 于 20%,则默认为使冗余电源设备进入休眠状态。 可使用 iDRAC 设置配置热备用功能。有关 iDRAC 设置的详情,请参阅 support.dell.com/manuals 上的《iDRAC7 用 户指南》。 卸下交流电源设备 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 系统正常运行时需要一个电源设备。在电源冗余系统中,每次只在电源开启的系统中卸下并更换一 个电源设备。 注: 如果可选的电缆管理臂妨碍您卸下电源设备,则可能必须打开闩锁并将其提起。有关电缆管理臂的详 情,请参阅系统的机架说明文件。 1. 断开电源电缆与电源及要卸下的电源设备的连接,从紧固带卸下电缆。 2.
4.
安装和连接安全接地线 警告: 对于使用 -(48-60) V 直流电源设备的设备,必须由合格的电工执行与直流电源连接相关的所有工作 并安全接地。请不要尝试亲自连接至直流电源或安装地线。所有电气布线必须遵从适用的当地或国家/地 区规范和惯例。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的所有安全 说明。 1. 剥除绿色/黄色线一端的绝缘层,露出约 4.5 毫米(0.175 英寸)的铜线。 2. 使用卷边工具(Tyco Electronics 58433-3 或类似工具)在绿色/黄色线(安全接地线)上卷起环形舌端子 (Jeeson Terminals Inc. R5-4SA 或类似端子)。 3. 使用锁紧垫圈配备的 #6-32 螺母,将安全接地线连接到系统背面的接地柱。 图 39: 安装和连接安全接地线 1. 安全接地线 2. 接地柱 3. 锁紧垫圈 4. 弹簧垫圈 5.
3. 警告: 为防止电源设备受到静电放电的损坏,在将配套连接器插入电源设备前,必须用橡胶盖覆盖固 定螺钉。 顺时针方向转动橡胶盖以将其安装到固定螺钉上。 4. 将配套连接器插入电源设备。 图 40: 安装直流输入电源线 1. 直流电源插槽 2. 橡胶盖 3. 固定螺钉(2 颗) 4. 直流电源连接器 5. –48 V 线 6. RTN 线 7. 接地线 卸下直流电源设备 警告: 对于使用 -(48-60) V 直流电源设备的设备,必须由合格的电工执行与直流电源连接相关的所有工作 并安全接地。请不要尝试亲自连接至直流电源或安装地线。所有电气布线必须遵从适用的当地或国家/地 区规范和惯例。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的所有安全 说明。 小心: 系统正常运行时需要一个电源设备。在电源冗余系统中,每次只在电源开启的系统中卸下并更换一 个电源设备。 注: 如果可选的电缆管理臂妨碍您卸下电源设备,则可能必须打开闩锁并将其提起。有关电缆管理臂的详 情,请参阅系统的机架说明文件。 1.
图 41: 卸下和安装直流电源设备 1. 连接器 2. 电源设备 3. 电源设备状态指示灯 4. 释放闩锁 5. 电源设备手柄 安装直流电源设备 警告: 对于使用 -(48-60) V 直流电源设备的设备,必须由合格的电工执行与直流电源连接相关的所有工作 并安全接地。请不要尝试亲自连接至直流电源或安装地线。所有电气布线必须遵从适用的当地或国家/地 区规范和惯例。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的所有安全 说明。 1. 验证两个电源设备是否属于同一种类型且是否拥有相同的最大输出功率。 注: 最大输出功率(以瓦特为单位)在电源设备标签上标示。 2. 卸下电源设备挡片(如果适用)。 3. 将新电源设备滑入机箱,直至电源设备完全就位且释放闩锁卡入到位。 4. 注: 如果打开了电缆管理臂的闩锁,请将其重新锁定。有关电缆管理臂的详情,请参阅系统的机架说 明文件。 连接安全接地线。 5. 在电源设备中安装直流电源连接器。 小心: 在连接电源线时,使用紧固带将线缆固定至电源设备手柄。 6.
图 42: 卸下和安装电源设备挡片 1. 电源设备挡片 安装电源设备挡片 注: 仅将电源设备挡片安装在第二个电源设备托架中。 要安装电源设备挡片,请将挡片与电源设备托架对齐,并将其插入机箱,直至卡入到位。 电源插入器板和配电板 卸下电源插入器板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 小心: 为防止损坏电源插入器板 (PIB),您必须先从系统上卸下电源设备模块,再卸下电源插入器板 或配电板 (PDB)。 2. 从机箱背面卸下电源设备模块。 3. 如果适用,向内旋转系统支脚,并将系统一侧放置在平稳的表面上。 4. 注: 对于安装了滚轮部件的系统,请确保使滚轮部件远离台面边缘扩展,并将系统放置在平稳的表面 上。 打开系统护盖。 5. 从硬盘驱动器背板和系统板上断开电源电缆。 6.
图 43: 卸下和安装电源插入器板 1. 电源插入器板 3. 配电板 2. 释放销 卸下配电板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 卸下电源插入器板。 2. 卸下将配电板 (PDB) 固定到机箱的六颗螺钉。 3.
1. 配电板 2. 螺钉(6 颗) 安装配电板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将配电板 (PDB) 上的螺孔对准机箱中的孔。 2. 使用 6 颗螺钉将 PDB 固定到机箱上。 3. 如果适用,安装电源插入器板。 4. 连接电源电缆至系统板和硬盘驱动器背板。 5. 在其原位置安装电源设备模块。 6. 合上系统护盖。 7. 如果适用,将系统垂直放置在平稳的表面上,并向外旋转系统支脚。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 安装电源插入器板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 安装配电板 (PDB)。 2.
5. 在其原位置安装电源设备模块。 6. 合上系统护盖。 7. 如果适用,将系统垂直放置在平稳的表面上,并向外旋转系统支脚。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 系统电池 更换系统电池 警告: 如果新电池安装不正确,可能会有爆炸的危险。请仅使用相同类型或制造商推荐的类型更换电池。 请参阅安全信息以了解更多内容。 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 将系统侧面朝下放置。 3. 打开系统护盖。 4. 卸下冷却导流罩。 5. 找到电池插槽。有关详情,请参阅“系统板连接器”。 小心: 为避免损坏电池连接器,在安装或卸下电池时必须牢固地支撑住连接器。 6. 要卸下电池,通过稳固地向下按连接器的正极端来支撑电池连接器。 图 44: 卸下和安装系统电池 1. 2.
11. 安装冷却导流罩。 12. 合上系统护盖。 13. 如果适用,以支脚为支撑点将系统垂直放置在平稳的表面上。 14. 将系统重新连接至电源插座,并打开系统,包括所有连接的外围设备。 15. 进入系统设置程序,以确认电池是否可以正常运行。 16. 在系统设置程序的 Time(时间)和 Date(日期)字段中输入正确的时间和日期。 17. 退出系统设置程序。 硬盘驱动器背板 根据您的配置,您的系统支持以下背板之一: • 3.5 英寸 x8 SAS/SATA 背板或 • 2.5 英寸 x4 Dell PowerEdge Express Flash (PCIe SSD) 背板或 • 3.5 英寸 x12 SAS/SATA 背板或 • 2.5 英寸 x16 SAS/SATA 背板 根据您的配置,您的系统支持以下背板组合: • 3.5 英寸 x8 SAS/SATA 背板和 2.5 英寸 x4 PCIe SSD 背板 • 2.5 英寸 x16 SAS/SATA 背板和 2.
图 45: 卸下和安装 PCIe SSD 硬盘驱动器背板 1. 硬盘驱动器连接器 2. PCIe SSD 硬盘驱动器背板 3. 释放卡舌 4. PCIe 电缆 5. 电源电缆 6.
图 46: 卸下和安装 3.5 英寸 (x8) SAS/SATA 背板 90 1. 背板电源连接器 2. 背板电源电缆 3. 释放销 4. 信号电缆 5. 背板 6.
图 47: 布线—3.5 英寸 (x8) SAS/SATA 背板 1. 背板上的电源连接器 2. 背板上的 SAS A 连接器 3. 系统板上的 SAS A 连接器 4. PDB 上的电源连接器 5. 系统板上的信号连接器 6.
图 48: 卸下和安装具有单个 PERC 卡的 3.5 英寸 (x8) SAS/SATA 背板 92 1. 电源连接器 2. 电源电缆 3. 释放销 4. SAS B 电缆 5. 信号电缆 6. 背板 7.
图 49: 布线—具有单个 PERC 卡的 3.5 英寸 (x8) SAS/SATA 背板 1. 背板上的电源连接器 2. 背板上的 SAS A 连接器 3. PERC 卡上的 SAS B 连接器 4. PERC 卡上的 SAS A 连接器 5. PDB 上的电源连接器 6. 系统板上的信号电缆 7. 背板上的信号电缆 8.
图 50: 卸下和安装 3.5 英寸 (x8) 加 2.5 英寸 (x4) SAS/SATA 背板 1. PCIe C 电缆 2. 电源连接器 3. PCIe D 电缆 4. PCIe B 电缆 5. 信号电缆 6. PCIe B 电缆 7. 电源电缆 8. 释放销 9. SAS B 电缆 10. 信号电缆 11. SAS A 电缆 94 12.
图 51: 布线—3.5 英寸 (x8) 加 2.5 英寸 (x4) SAS/SATA 背板 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. PCIe SSD 背板上的 PCIe B 电缆 PCIe SSD 背板上的 PCIe A 电缆 PERC 卡上的 3.5 英寸背板的 SAS B 电缆 PERC 卡上的 3.
12. 13. 14. 15. 16. 17. 18. 3.5 英寸背板上的 SAS B 电缆 3.5 英寸背板上的 SAS A 电缆 背板电源电缆 背板电源连接器 PCIe SSD 背板信号电缆 PCIe SSD 背板上的 PCIe D 电缆 PCIe SSD 背板上的 PCIe C 电缆 图 52: 卸下和安装 3.5 英寸 (x12) SAS/SATA 背板 96 1. 电源连接器 2. 电源电缆 3. SAS B 电缆 4. 释放销 5. SAS A 电缆 6. 信号电缆 7.
图 53: 布线—3.5 英寸 (x12) SAS/SATA 背板 1. 2. 3. 4. 5. 6. 7. 8.
图 54: 卸下和安装 2.5 英寸 (x16) SAS/SATA 背板 98 1. 背板 2. 信号电缆 3. 释放销 4. 电源电缆 5. 电源连接器 6. SAS A 电缆 7.
图 55: 布线—2.5 英寸 (x16) SAS/SATA 背板 1. PERC 上的 SAS B 连接器 2. PERC 上的 SAS A 连接器 3. PDB 上的电源连接器 4. 系统板上的信号连接器 5. 背板上的 SAS A 连接器 6. 背板上的 SAS B 连接器 7. 背板上的电源连接器 8.
图 56: 卸下和安装 2.5 英寸 (x16) 加 2.5 英寸 (x4) SAS/SATA 背板 1. 背板 2. PCIe D 电缆 3. 电源电缆 4. PCIe C 电缆 5. PCIe B 电缆 6. 信号电缆 7. PCIe A 电缆 8. 释放销 9. 信号电缆 10. 电源电缆 11. SAS A 电缆 13. 背板 100 12.
图 57: 布线—2.5 英寸 (x16) 加 2.5 英寸 (x4) SAS/SATA 背板 1. PCIe SSD 背板上的 PCIe B 电缆 2. PCIe SSD 背板上的 PCIe A 电缆 3. PERC 上的 SAS B 连接器 4. PERC 上的 SAS A 连接器 5. PCIe 桥接卡上的 PCIe D 电缆 6. PCIe 桥接卡上的 PCIe C 电缆 7. PCIe 桥接卡上的 PCIe B 电缆 8. PCIe 桥接卡上的 PCIe A 电缆 9. PDB 上的 PCIe SSD 背板电源连接器 10. PDB 上的背板电源连接器 11. 背板上的 SAS A 连接器 12. 背板上的 SAS B 连接器 13. 背板上的电源连接器 14. 背板上的信号连接器 15. PCIe SSD 背板上的信号连接器 16. PCIe SSD 背板上的电源连接器 17. PCIe SSD 背板上的 PCIe D 电缆 18.
图 58: 卸下和安装具有两个 PERC 卡的 2.5 英寸 (x32) SAS/SATA 背板 102 1. 信号电缆 2. 释放销 3. 电源电缆 4. SAS A 电缆 5. SAS B 电缆 6. 信号电缆 7. 电源电缆 8. SAS A 电缆 9. SAS B 电缆 10.
图 59: 布线—具有两个 PERC 卡的 2.5 英寸 (x32) SAS/SATA 背板 1. 第 2 个 PERC 上的 SAS A 连接器 2. 第 2 个 PERC 上的 SAS B 连接器 3. 第 1 个 PERC 上的 SAS B 连接器 4. 第 1 个 PERC 上的 SAS A 连接器 5. PDB 上的背板 1 电源连接器 6. PDB 上的背板 2 电源连接器 7. 系统板上的信号连接器 1 8. 系统板上的信号连接器 2 9. 背板 2 上的 SAS A 连接器 10. 背板 2 上的 SAS B 连接器 11. 背板 2 上的电源连接器 12. 背板 2 上的信号连接器 13. 背板 1 上的电源连接器 14. 背板 1 上的 SAS B 连接器 15. 背板 1 上的 SAS A 连接器 16.
图 60: 卸下和安装具有单个 PERC 卡的 2.5 英寸 (x32) SAS/SATA 背板 1. 信号电缆 2. 释放销 3. 电源连接器 4. SAS A 电缆 5. SAS B 电缆 6. SAS A1 电缆 7. SAS B1 电缆 8. 信号电缆 9. 电源电缆 10. SAS A1 电缆 11. SAS B1 电缆 104 12.
图 61: 布线—具有单个 PERC 卡的 2.5 英寸 (x32) SAS/SATA 背板 1. 背板 1 上的信号连接器 2. 背板 1 上的 SAS B 连接器 3. 背板 1 上的 SAS A 连接器 4. PERC 上的 SAS B 连接器 5. PERC 上的 SAS A 连接器 6. PDB 上的背板 1 电源连接器 7. PDB 上的背板 2 电源连接器 8. 系统板上的背板 1 信号连接器 9. 系统板上的背板 2 信号连接器 10. 背板 2 SAS A 连接器 11. 背板 2 SAS B 连接器 12. 背板 2 电源连接器 13. 背板 2 信号连接器 14. 背板 1 电源连接器 15. 背板 1 SAS B1 连接器 16.
安装硬盘驱动器背板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 使用机箱基座的挂钩作为导向器以对齐硬盘驱动器背板。 2. 向下滑动硬盘驱动器背板,将其固定到位。 3. 注: 对于 Dell PowerEdge Express Flash (PCIe SSD) 背板,向下滑动硬盘驱动器背板直至释放卡舌卡入到 位。 将 SAS/SATA/SSD 数据、信号和电源电缆连接至背板。请参阅本说明文件中提供的布线说明。 4. 如果适用,装回冷却风扇部件。 5. 装回冷却导流罩。 6. 将硬盘驱动器安装在其原始位置。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 9.
1. 系统顶盖 2. 螺钉(6 颗) 安装系统顶盖 注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 1. 将顶盖稍稍朝向系统正面。 2. 将顶盖与控制面板和机箱顶部的槽口对齐。 3. 使用螺钉将护盖固定到机箱上。 系统左侧机盖 在进行卸下和安装操作时使用以下过程: • 塔式模式下的控制面板 • 任意模式下的 LCD 模块 卸下系统左侧机盖 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 将系统侧面朝下放置。 3.
4. 拧下用于将左侧机盖固定在机箱后端的三颗螺钉。 5. 从底部向上推动机盖,轻轻取下机盖。 6. 从系统中取出机盖。 图 62: 卸下和安装系统左侧机盖 1. 左侧机盖 3. 螺钉(3 颗) 2. 底部螺钉 安装系统左侧机盖 注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 1. 装回系统顶盖。请参阅“安装系统顶盖”。 2. 将左侧机盖稍稍朝向系统顶部,使左侧机盖上的卡舌与机箱底部的插槽对齐。 3. 使用螺钉将左侧机盖固定到机箱上。 控制面板 卸下控制面板—塔式模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4.
5. 卸下顶盖。请参阅“卸下系统顶盖”。 6. 拧下用于将控制面板固定到机箱上的螺钉。 7. 如果适用,卸下冷却风扇部件。 小心: 拔下控制面板电缆时,请勿用力过度,以免损坏连接器。 8. 从系统板上拔下控制面板电缆、LCD 电缆和控制面板 USB 电缆。 9. 将控制面板滑出机箱。 10. 拔下控制面板上的电缆。 图 63: 卸下和安装控制面板—塔式模式 1. 控制面板 2. 螺钉 安装控制面板—塔式模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将控制面板电缆、LCD 电缆和控制面板 USB 电缆连接至控制面板模块。 2. 将控制面板与机箱中的控制面板插槽对齐并将其插入插槽。 3. 使用螺钉将控制面板固定到机箱上。 4. 将控制面板电缆、LCD 电缆和控制面板 USB 电缆连接至系统板。 5. 安装系统顶盖。请参阅“安装系统顶盖”。 6.
10. 如果有,请安装前挡板。 卸下控制面板—机架模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4. 拧下用于将控制面板固定到机箱上的螺钉。 小心: 卸下控制面板时,请勿用力过度,以免损坏连接器。 5. 从系统板上拔下连接至控制面板模块的所有电缆。 6. 将控制面板模块轻轻滑出机箱。 7. 提起控制面板的边角边缘以从控制面板模块的插槽中松开卡舌。 8. 旋转控制面板的左侧边缘使其脱离机箱,从而从机箱上松开。 图 64: 卸下和安装控制面板模块—机架模式 1. 110 控制面板模块 2.
图 65: 从处于机架模式的控制面板模块卸下和安装控制面板 1. 控制面板 3. 控制面板 USB 电缆 2. 控制面板电缆 安装控制面板—机架模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将控制面板电缆和控制面板 USB 电缆连接至控制面板模块。 2. 将控制面板滑入机箱。 3. 使用螺钉将控制面板固定到机箱上。 4. 将控制面板电缆和控制面板 USB 电缆连接至系统板。 5. 合上系统护盖。 6. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 7. 如果有,请安装前挡板。 卸下 Control-Panel 板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1.
5. 拧下用于将 Control-Panel 板固定到控制面板上的螺钉。 6. 从控制面板中提出 Control-Panel 板。 图 66: 卸下和安装 Control-Panel 板 1. Control-Panel 板 2. 螺钉(3 颗) 安装 Control-Panel 板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将 control-panel 板与控制面板对齐。 小心: 小心不要损坏覆盖 ID 开关的聚酯。 2. 拧紧三颗螺钉,将 control-panel 板固定到控制面板上。 3. 安装控制面板。 4. 合上系统护盖。 5. 将系统和外围设备重新连接至各自的电源,并打开它们。 6.
卸下 LCD 模块—塔式模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下左侧机盖。请参阅“系统左侧机盖”。 4. 卸下顶盖。请参阅“卸下系统顶盖”。 5. 卸下控制面板部件。 6. 断开 LCD 电缆的连接。 7. 拧下用于将 LCD 模块固定到控制面板上的螺钉。 8. 从控制面板部件中取出 LCD 模块。 图 67: 卸下和安装塔式模式下的 LCD 模块 1. LCD 模块 3. LCD 电缆 2.
6. 安装系统左侧机盖。请参阅“安装系统左侧机盖”。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 9. 如果有,请安装前挡板。 卸下 LCD 模块—机架模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 从机架中卸下系统。 4. 卸下系统左侧机盖。请参阅“卸下系统左侧机盖”。 注: LCD 模块位于左侧面板。 5. 从机箱左侧拧下用于将此模块固定到机箱上的螺钉。 小心: 卸下 LCD 模块时,请勿用力过度,以免损坏连接器。 6. 推拉 LCD 模块,以一定角度转动它,将其从侧面板上松开。 7.
安装 LCD 模块—机架模式 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将 LCD 电缆从电缆固定支架中穿过,并穿过 LCD 模块插槽旁边的机箱的内壁。 2. 如果适用,请卸下 LCD 模块挡板。 3. 将 LCD 模块插入 LCD 模块插槽。 4. 将 LCD 电缆连接到 LCD 模块。 5. 装回螺钉。 6. 将 LCD 电缆连接至系统板。 7. 装回系统左侧机盖。请参阅“安装系统左侧机盖”。 8. 合上系统护盖。 9. 在机架中重新安装系统。 10. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 11.
图 69: 卸下和安装 VGA 模块 1. 控制面板 2. VGA 模块 3. 控制面板电缆 4. 控制面板 USB 电缆 安装 VGA 模块 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 将 VGA 模块上的插槽与控制面板上的挂钩对齐。 2. 按下 VGA 模块直至挂钩卡入到位。 3. 安装控制面板。 4. 合上系统护盖。 5. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 6.
小心: 如果您通过密钥使用可信程序模块 (TPM),在程序或系统设置期间您会看到要求您创建恢复密钥的 提示。请务必创建并安全存储此恢复密钥。如果您更换此系统板,则必须在重新启动系统或程序时提供 此恢复密钥,然后才能访问硬盘驱动器上的加密数据。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 卸下以下组件: a. 冷却导流罩 b. 冷却风扇部件(如果适用) c. PCIe 卡固定器 d. 内存模块 e. 所有扩充卡 警告: 在系统关机后一定时间内,散热器和处理器都会很烫手。请让它们冷却下来后再进行操 作。 f. 散热器和处理器 g. 内部双 SD 模块 h. 内部 USB 钥匙(如果已安装) 4. 断开系统板的所有电缆连接。 小心: 在从机箱中卸下系统板时,小心不要损坏系统识别按钮。 5. 抓住系统板固定器,提起蓝色的释放销,并将系统板滑向系统正面。 小心: 请勿通过抓住内存模块、处理器或其它组件来拿出系统板组件。 图 70: 卸下系统板 1. 系统板 2.
安装系统板 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 打开新系统板部件的包装。 小心: 请勿通过抓住内存模块、处理器或其它组件来拿出系统板组件。 2. 手握触点,将系统板向下放入机箱。 3. 将系统板推向机箱后侧,直至系统板卡入到位。 4. 装回以下组件: a. 散热器和处理器 b. 内部双 SD 模块 c. 内部 USB 钥匙(如果适用) d. 内存模块 e. 扩充卡 f. 冷却风扇部件(如果适用) g. 冷却导流罩 h. PCIe 卡固定器 5. 将所有电缆重新连接至系统板。请参阅本说明文件中的电缆布线图。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 8. 导入新的或现有的 iDRAC Enterprise 许可证。有关详情,请参阅 support.dell.
系统故障排除 4 安全第一 —— 为您和您的系统着想 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 系统启动失败故障排除 如果在通过 UEFI 引导管理器安装操作系统后将系统引导至 BIOS 引导模式,系统会挂起。反之亦然。您必须引 导至安装操作系统时所用的相同引导模式。 对于所有其他启动问题,请注意屏幕上显示的系统消息。 外部连接故障排除 对任何外部设备进行故障排除之前,请确保所有外部电缆均已牢固地连接至系统上的外部连接器。 视频子系统故障排除 1. 检查显示器与系统和电源的连接。 2. 检查系统到显示器之间的视频接口布线。 3. 运行相应的诊断检测程序。 如果检测程序运行成功,则问题与视频硬件无关。 如果检测程序运行失败,请参阅“获得帮助”。 USB 设备故障排除 按照以下步骤对 USB 键盘/鼠标进行故障排除。对于其它 USB 设备,请转至步骤 7。 1.
9. 重新连接,每次打开一个 USB 设备的电源。 10. 如果某个设备导致了相同的问题,请关闭该设备的电源,使用已知正常的电缆更换 USB 电缆,然后再打 开该设备的电源。 如果所有故障排除措施均失败,请参阅“获得帮助”。 串行 I/O 设备故障排除 1. 关闭系统和所有已连接至串行端口的外围设备。 2. 3. 将串行接口电缆更换为可正常工作的电缆,并打开系统和串行设备。 如果问题得以解决,请使用已知正常的电缆更换接口电缆。 关闭系统和串行设备,将该设备更换为同类设备。 4. 打开系统和串行设备。 如果问题仍然存在,请参阅“获得帮助”。 NIC 故障排除 1. 运行相应的诊断检测程序。有关可用的诊断检测程序,请参阅“使用系统诊断程序”。 2. 重新启动系统,并检查与 NIC 控制器相关的任何系统信息。 3.
• 扩充卡提升板(如果存在) • 扩充卡 • 电源设备 • 冷却风扇部件(如果有) • 冷却风扇 • 处理器和散热片 4. • 内存模块 使系统彻底干燥至少 24 小时。 5. 重新安装您在步骤 3 中卸下的组件。 6. 合上系统护盖。 7. 打开系统和已连接的外围设备。 如果系统未正常启动,请参阅“获得帮助”。 8. 如果系统正常启动,请关闭系统并重新安装所有卸下的扩充卡。 9. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 如果检测程序运行失败,请参阅“获得帮助”。 受损系统故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3.
注: 如果长期(几个星期或几个月)关闭系统电源,则 NVRAM 可能会丢失系统配置信息。这种情况是由 有故障的电池引起的。 1. 在系统设置程序中重新输入时间和日期。 2. 关闭系统并断开系统与电源插座的连接,然后至少等待一小时。 3. 将系统重新连接至电源插座,并打开系统。 4. 进入系统设置程序。 如果系统设置程序中的日期和时间不正确,请检查 SEL 中的系统电池信息。 如果问题仍未解决,请参阅“获得帮助”。 注: 某些软件可能导致系统时间加快或减慢。如果除系统设置程序期间以外,系统似乎正常运行,则问题 可能是由软件而不是由有故障的电池引起的。 电源设备故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 通过拆卸和重新安装的方法来重置电源设备。 注: 安装完电源设备后,请等待几秒钟,以便系统识别电源设备并确定其是否可以正常工作。 2.
系统内存故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 2. 3. 如果系统可以操作,请运行相应的诊断检测程序。有关可用的诊断测试程序,请参阅“使用系统诊断程 序”。 如果诊断程序指示出现故障,请按照诊断程序提供的更正措施进行操作。 如果系统无法操作,请关闭系统和连接的外围设备,并且拔下系统的电源线。等待至少 10 秒钟,然后将 系统重新连接到电源。 打开系统和连接的外围设备,并留意屏幕上的信息。 如果显示错误信息,指示特定内存模块有故障,请转至步骤 12。 4. 进入系统设置程序并检查系统内存设置。必要时对内存设置进行任何更改。 如果内存设置符合所安装的内存,但仍指示存在问题,请转至步骤 12。 5. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 6. 打开系统护盖。 7. 检查内存通道,确保内存填充无误。 8. 在各自插槽中重置内存模块。 9.
8. 插入已知能正常工作的其它 USB 闪存盘。 9. 合上系统护盖。 如果问题仍未解决,请参阅“获得帮助”。 SD 卡故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 注: 某些 SD 卡的卡上具有物理写保护开关。如果打开此写保护开关,则 SD 卡无法写入。 1. 进入系统设置程序,确保已启用 Internal SD Card Port(内部 SD 卡端口)。 2. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 3. 打开系统护盖。 小心: 如果在系统设置程序的 Integrated Devices(集成设备)屏幕中将 Internal SD Card Redundancy (内部 SD 卡冗余)选项设置为 Mirror Mode(镜像模式),则必须按照步骤 4 至步骤 6 中的说明进 行操作以避免丢失数据。 4.
9. 合上系统护盖。 如果问题仍未解决,请参阅获得帮助。 硬盘驱动器故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 此故障排除步骤可能会清除硬盘驱动器上存储的数据。继续进行之前,请备份硬盘驱动器上的所有 文件。 1. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 2. 根据诊断检测程序的结果,按需要继续执行以下步骤。 如果系统中存在 RAID 控制器且在 RAID 阵列中配置了硬盘驱动器,则执行下列步骤: a. 重新启动系统,并在系统启动期间按 以运行 Lifecycle Controller(生命周期控制器),然后运行 硬件配置向导检查 RAID 配置。 有关 RAID 配置的信息,请参阅 Lifecycle Controller(生命周期控制器)说明文件或联机帮助。 b. 确保已正确配置 RAID 阵列的硬盘驱动器。 c.
c. 重新安装其中一个扩充卡。 d. 合上系统护盖。 e. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 如果仍然指示存在问题,请参阅“获得帮助”。 处理器故障排除 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 运行相应的诊断检测程序。有关可用的诊断检测程序,请参阅“使用系统诊断程序”。 2. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 3. 打开系统护盖。 4. 确保已正确安装了处理器和散热片。 5. 合上系统护盖。 6.
使用系统诊断程序 5 如果您的系统出现问题,请在致电 Dell 寻求技术帮助之前运行系统诊断程序。运行系统诊断程序旨在检测系统 的硬件,它不需要其它设备,也不会丢失数据。如果您无法自行解决问题,维修和支持人员可以使用诊断程序 的检测结果帮助您解决问题。 Dell Online Diagnostics Dell Online Diagnostics 是一组独立的诊断程序或测试模块套件,允许在生产环境的系统上运行诊断测试,并帮 助最大程度地延长系统正常工作的时间。Online Diagnostics 使您可以对硬盘驱动器、物理内存、网络接口卡 (NIC) 等机箱和存储组件运行诊断测试。可以使用图形用户界面 (GUI) 或命令行界面 (CLI) 对 Online Diagnostics 在 系统上查找到的硬件运行诊断测试。有关使用诊断程序的信息,请参阅 Software → Serviceability Tools 下的 Dell Online PowerEdge Diagnostics User’s Guide(Dell Online PowerEdge Diagnostics 用户指南),网址:dell.
系统诊断程序控制 菜单 说明 配置 显示所有检测到的设备的配置和状态信息。 Results(结果) 显示执行的所有检测的结果。 系统运行状况 提供系统性能的当前概况。 事件日志 显示系统上运行的所有检测的结果的时间戳日志。如果至少记录一个事件描述,则显示 此选项。 有关嵌入式系统诊断程序的信息,请参阅 dell.
6 跳线和连接器 系统板跳线设置 有关重设密码跳线以禁用密码的信息,请参阅“禁用已忘记的密码”。 表.
系统板连接器 图 71: 系统板跳线和连接器 项目 连接器 说明 1 SLOT1 PCIe 卡连接器 1 2 SLOT2 PCIe 卡连接器 2 3 SLOT3 PCIe 卡连接器 3 4 SLOT4 PCIe 卡连接器 4 5 NIC1 NIC1 连接器 6 NIC2 NIC2 连接器 7 B1、B5、B9、B2、B6、B10 内存模块插槽 8 FAN1 冷却导流罩风扇连接器 9 ID_BTN 系统识别按钮 10 CMA_JACK (电缆固定臂)系统识别连接器 11 IDRAC_RJ45 iDRAC 连接器 130
项目 连接器 说明 12 USB 1 至 6 USB 连接器 13 FAN2 冷却导流罩风扇连接器 14 VGA 视频连接器 15 B12、B8、B4、B11、B7、B3 内存模块插槽 16 COM 串行连接器 17 SLOT5 PCIe 卡连接器 5 18 SLOT6 PCIe 卡连接器 6 19 J43 NA 20 SLOT7 PCIe 卡连接器 7 21 PIN 系统板释放销 22 PIB_CONN PIB 信号连接器 23 INT_USB 内部 USB 连接器 24 FAN6 系统风扇连接器 25 PWR_CONN_2 PIB 信号连接器 26 INTRUSION 机箱防盗开关连接器 27 A10、A6、A2、A9、A5、A1 内存模块插槽 28 BP_SIG2 背板信号连接器 2 29 FAN5 系统风扇连接器 30 PWR_CONN_1 电源连接器 31 BP_SIG0、BP_SIG1 Dell PowerEdge Express Flash (PCIe SSD) 信号连 接
禁用已忘记的密码 系统的软件安全保护功能包括系统密码和设置密码功能。密码跳线可以启用或禁用这些密码功能,也可以清除 当前使用的任何密码。 小心: 多数维修只能由经过认证的维修技术人员执行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 将系统板跳线上的跳线从插针 2 和 4 移到插针 4 和 6。 4. 合上系统护盖。 当跳线设置在插针 4 和 6 上时,现有密码在系统引导前不会被禁用(清除)。但在设定新的系统和/或设置 密码前,您必须将跳线移回插针 2 和 4。 注: 如果跳线处于插针 4 和 6 上时设定新的系统和/或设置密码,系统将在下一次引导时禁用新密码。 5. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 6. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 7. 打开系统护盖。 8.
7 技术规格 处理器 处理器类型 一个或两个 Intel Xeon 处理器 E5-2600 产品系列 扩展总线 总线类型 PCI Express 第 3 代和第 2 代 扩充槽: (插槽 1)一个全高、全长 x8 链路 (插槽 2)一个全高、全长 x16 链路 (插槽 3)一个全高、全长 x4 链路 注: 插槽 3 仅是 PCI Express 第 2 代。 (插槽 4)一个全高、全长 x16 链路 注: 必须安装两个处理器才能使用插槽 5 至 7。 (插槽 5)一个全高、全长 x16 链路 (插槽 6)一个全高、全长 x8 链路 (插槽 7)一个全高、全长 x16 链路 内存 体系结构 800 MT/s、1066 MT/s、1333 MT/s 或 1600 MT/s DDR3 已 注册、非缓冲或负载减少的错误纠正代码 (ECC) DIMM 支持高级 ECC 或内存优化操作 内存模块插槽 24 个 240 针插槽 内存模块容量 LRDIMM 32 GB 四列 RDIMM 2 GB、4 GB、8 GB 或 32 GB 单列、双列或四列 16 GB 单列或双列 UDIMM 最小 RAM
内存 LRDIMM 最大 768 GB RDIMM 最大 512 GB UDIMM 最大 128 GB 驱动器 硬盘驱动器 四硬盘驱动器系统 多达四个 3.5 英寸、内部、热插拔 SSD、SATA 或 SATA 硬盘驱动器 硬盘驱动器插槽 0 至 3(硬盘驱动器插槽 4 至 7 不支 持任何硬盘驱动器,而是安装有硬盘驱动器挡片) 八硬盘驱动器系统 多达八个 3.5 英寸、内部、热插拔 SAS、SATA 或近 线 SAS 硬盘驱动器 硬盘驱动器插槽 0 至 7 十二硬盘驱动器系统 多达十二个 3.5 英寸、内部、热插拔 SAS、SATA、 SATA SSD 或近线 SAS 硬盘驱动器 硬盘驱动器插槽 0 至 11 八加四硬盘驱动器系统 多达八个 3.5 英寸、内部、热插拔 SAS、SATA、 SATA SSD 或近线 SAS 硬盘驱动器,以及四个 Dell PowerEdge Express Flash 设备 (PCIe SSD) 十六硬盘驱动器系统 多达十六个 2.
连接器 串行 9 针、DTE、16550 兼容 USB 六个高速 USB 主机 视频 15 针 VGA 前端 USB 两个高速 USB 主机 视频 15 针 VGA 注: 前 VGA 端口仅适用于机架配置。 外部 vFlash 内存卡 一个 vFlash 内存卡插槽 内部 USB 一个 4 针、USB 2.
扩展操作温度 • • • • • • • • 请勿在 5°C 以下执行冷启动。 指定的操作温度适用的最高海拔高度为 2000 米 ( 6560 英尺)。 不支持 Express Flash。 不支持 GPU。 不支持 LRDIMM。 不支持 130 W 4 核处理器、135 W 处理器和 150 W 处理器。 不支持非冗余电源设备。 不支持非 Dell 认证的外围设备卡和/或超过 25 W 的外围设备卡。 环境参数 注: 有关特定系统配置的环境测量值的附加信息,请参阅 dell.com/environmental_datasheets。 温度 最高温度梯度(操作和存储) 20 °C/h (36 °F/h) 存储温度范围 –40 °C 至 65 °C(–40 °F 至 149 °F) 温度(连续操作) 温度范围(在海拔小于 950 米或 3117 英尺时) 在设备无直接光照的情况下,10 °C 至 35 °C(50 °F 至 95 °F)。 湿度百分比范围 最大露点为 26 °C (78.
环境参数 最高达 35 °C (95 °F) 最高温度在 950 米(3,117 英尺)以上时按 1 °C/300 米 (1 °F/547 英尺)降低。 35 °C 至 40 °C(95 °F 至 104 °F) 最高温度在 950 米(3,117 英尺)以上时按 1 °C/175 米 (1 °F/319 英尺)降低。 40 °C 至 45 °C(104 °F 至 113 °F) 最高温度在 950 米(3,117 英尺)以上时按 1 °C/125 米 (1 °F/228 英尺)降低。 微粒污染 注: 此部分定义了为避免 IT 设备因微粒及气体污染物受到损伤和/或发生故障的限制。如果已经确定微粒 或气体污染的程度超出了下面说明的限制并成为导致设备损伤和/或故障的原因,则您可能有必要对导致 设备损伤和/或故障的环境条件进行补救。对环境条件的补救措施是客户的责任。 空气过滤 注: 仅适用于数据中心环境。空气过滤要求不 适用于旨在数据中心之外,诸如办公室或工 厂车间等环境,使用的 IT 设备。 导电灰尘 注: 适用于数据中心和非数据中心环境。 腐蚀性灰尘 注: 适用于数据中心和非数据中心环境。 按照
8 系统消息 LCD 信息 注: 仅在您的系统具有 LCD 显示屏时可用。 LCD 信息由简短的文字信息组成,指代系统事件日志 (SEL) 中记录的事件。有关 SEL 和配置系统管理设置的信 息,请参阅系统管理软件说明文件。 注: 如果系统无法引导,按下系统 ID 按钮至少 5 秒钟,直至 LCD 上显示错误代码。记下该代码,然后参 阅“系统错误消息”。 查看 LCD 信息 如果发生系统错误,LCD 屏幕将变为琥珀色。请按 Select(选择)按钮,查看错误信息或状态信息列表。使用 向左和向右按钮突出显示错误编号,然后按 Select(选择)按钮查看该错误。 删除 LCD 信息 对于与传感器有关的故障,例如温度、电压、风扇等,当传感器恢复至正常状态时,LCD 信息将被自动删除。 对于其它故障,必须采取措施才能将信息从显示器中删除: • 清除 SEL — 您可以远程执行该任务,但是系统的事件历史记录将丢失。 • 关闭电源再打开 — 关闭系统电源并断开其与电源插座的连接;等待大约 10 秒钟,重新连接电源电缆,然 后重新启动系统。 系统错误消息 显示器中出现的系统消息,通知您系统可能出现的问题。这
错误代码 消息信息 操作 AMP0303 ASR0001 ASR0002 ASR0003 审查系统电源策略。 2. 检查系统日志确认电源相关故障。 3. 审查系统配置更改。 4. 如果问题仍然存在,请参阅“获得帮助”。 消息 The system board current is greater than the upper critical threshold.(系统板 电流高于上限临界阈值。) LCD 消息 System board current is outside of range.(系统板 电流超出范围。) 详细信息 系统板 电流超出适宜范围。 操作 ASR0000 1. 1. 审查系统电源策略。 2. 检查系统日志确认电源相关故障。 3. 审查系统配置更改。 4. 如果问题仍然存在,请参阅“获得帮助”。 消息 The watchdog timer expired.
错误代码 BAT0002 BAT0017 CPU0000 CPU0001 CPU0005 140 消息信息 操作 检查操作系统、应用程序、硬件和系统事件日志以排查异常事 件。 消息 The system board battery has failed.(系统板电池失效。) LCD 消息 The system board battery has failed. Check battery.(系统板电池失 效。检查电池。) 详细信息 系统板电池缺失或故障。 操作 请参见“获得帮助”。 消息 The battery has failed.(电池 失效。) LCD 消息 The battery has failed. Check battery.(电池 失 效。检查电池。) 详细信息 电池 可能出现缺失、故障因为温度问题导致无法充电。 操作 检查系统风扇。如果问题仍然存在,请参阅“获得帮助”。 消息 CPU has an internal error (IERR).
错误代码 CPU0010 CPU0023 CPU0204 消息信息 操作 检查所支持的处理器类型的技术规格。 消息 CPU is throttled.(CPU 被节流。) 详细信息 因为温度或电源情况导致 CPU 被节流。 操作 查阅系统日志排查电源或温度异常。 消息 CPU is absent.(CPU 缺失。) LCD 消息 CPU is absent. Check CPU.(CPU 缺失。检查 CPU。) 操作 验证处理器安装。如果存在,则重新安装处理器。 消息 CPU voltage is outside of range.(CPU 电压超出范围。) LCD 消息 CPU voltage is outside of range. Re-seat CPU.
错误代码 消息信息 详细信息 操作 CPU0702 142 2. 检查系统和操作系统日志以排查异常。如果未发现异常, 则继续。 关闭系统并断开输入电源一分钟。 3. 确保处理器安装正确。 4. 重新提供输入电源并打开系统。 5. 如果问题仍然存在,请参阅“获得帮助”。 CPU bus parity error detected.(检测到 CPU 总线奇偶校验错 误。) LCD 消息 CPU bus parity error detected. Power cycle system.(检测到 CPU 总 线奇偶校验错误。系统电源关闭然后打开。) 详细信息 系统事件日志和操作系统日志也许会表明异常出现在处理器之 外。 1. 2. 检查系统和操作系统日志以排查异常。如果未发现异常, 则继续。 关闭系统并断开输入电源一分钟。 3. 确保处理器安装正确。 4. 重新提供输入电源并打开系统。 5. 如果问题仍然存在,请参阅“获得帮助”。 消息 CPU bus initialization error detected.
错误代码 消息信息 LCD 消息 CPU machine check error detected. Power cycle system. (检测到 CPU 机器检查错误。系统电源关闭然后打 开。) 详细信息 系统事件日志和操作系统日志也许会表明异常出现在处理器之 外。 操作 FAN0000 FAN0001 FAN1201 HWC1001 1. 2. 检查系统和操作系统日志以排查异常。如果未发现异常, 则继续。 关闭系统并断开输入电源一分钟。 3. 确保处理器安装正确。 4. 重新提供输入电源并打开系统。 5. 如果问题仍然存在,请参阅“获得帮助”。 消息 Fan RPM is less than the lower warning threshold.
错误代码 HWC2003 HWC2005 MEM0000 MEM0001 MEM0007 144 消息信息 消息 The storage cable is not connected, or is improperly connected.(未连接存储设备 电缆,或连接不正确。) LCD 消息 Storage cable or interconnect failure. Check connection. (存储设备 电缆或互联故障。请检查连接。) 详细信息 电缆可能是正常运行所必需的。系统功能可能降级。 操作 检查电缆是否存在,然后重新安装或重新连接。 消息 The system board cable is not connected, or is improperly connected.(未连接系统板 电缆,或连接不正确。) LCD 消息 System board cable connection failure. Check connection.
错误代码 MEM0701 MEM0702 MEM1205 MEM1208 MEM8000 消息信息 消息 Correctable memory error rate exceeded for .( 的可纠正内存错误比率超限。) 详细信息 内存可能无法操作。这是未来可能发生的不可纠正错误的早期 迹象。 操作 重新安装内存模块。如果问题仍然存在,请参阅“获得帮助”。 消息 Correctable memory error rate exceeded for .( 的可纠正内存错误比率超限。) LCD 消息 Correctable memory error rate exceeded for . Re-seat memory.
错误代码 PCI1302 PCI1304 PCI1308 PCI1320 PCI1342 146 消息信息 操作 检查系统日志排查内存异常。重新安装位于 处的内 存。 消息 A bus time-out was detected on a component at bus device function .(总线 设备 功能 的组件上检测到总线超时。) 详细信息 系统性能可能降级。设备没能对事务做出响应。 操作 关闭并打开输入电源,更新组件驱动程序,如果设备可卸下, 则重新安装设备。 消息 An I/O channel check error was detected.(检测到 I/O 通道检查错 误。) LCD 消息 I/O channel check error detected. Power cycle system.
错误代码 PCI1348 PCI1360 PDR0001 PDR1016 PST0128 消息信息 详细信息 系统性能可能降级,或系统可能无法运行。 操作 关闭并打开输入电源,更新组件驱动程序,如果设备可卸下, 则重新安装设备。 消息 A PCI parity error was detected on a component at slot . (插槽 的组件上检测到 PCI 奇偶校验错误。) LCD 消息 PCI parity error on slot . Re-seat PCI card.(插槽 上的 PCI 奇偶校验错误。重新安装 PCI 卡。) 详细信息 系统性能可能降级,或系统可能无法运行。 操作 关闭并打开输入电源,更新组件驱动程序,如果设备可卸下, 则重新安装设备。 消息 A bus fatal error was detected on a component at slot .
错误代码 PST0129 PSU0001 PSU0002 PSU0003 PSU0006 148 消息信息 LCD 消息 No memory is detected. Inspect memory devices.(未检测到内存。 请检查内存设备。) 详细信息 系统 BIOS 无法检测到系统中的内存。 操作 重新安装内存模块。如果问题仍然存在,请参阅“获得帮助”。 消息 Memory is detected, but is not configurable.(检测到内存,但该内 存不可配置。) LCD 消息 Memory is detected, but is not configurable. Check memory devices. (检测到内存,但该内存不可配置。检查内存设备。) 详细信息 系统 BIOS 检测到内存,但无法基于系统运行对其进行配置。 操作 将系统内存安装与支持的系统内存配置进行比较。 消息 Power supply failed.
错误代码 PSU0016 消息信息 详细信息 电源设备的输入类型和额定功率应当相同。 操作 安装匹配的电源设备,并查阅此手册中的适当配置。 消息 Power supply is absent.(电源设备 缺失。) LCD 消息 PSU is absent. Check PSU.(PSU 缺失。检查 PSU。) 详细信息 电源设备已卸下或出现故障。 操作 PSU0031 PSU0032 PSU0033 PSU0034 1. 卸下并重新安装电源设备。 2. 检查系统中的线缆和子系统组件以排查损坏。 3. 如果问题仍然存在,请参阅“获得帮助”。 消息 Cannot communicate with power supply .(无法与电源设 备 通信。) LCD 消息 Cannot communicate with PSU . Re-seat PSU.
错误代码 消息信息 LCD 消息 An under voltage fault detected on PSU . Check power source.(在 PSU 上检测到电压过低故障。请检查电 源。) 详细信息 此故障可能是系统中的电缆或子系统组件发生电力问题而导 致。 操作 PSU0035 PSU0036 PSU0076 150 卸下并重新安装电源设备。 2. 检查系统中的线缆和子系统组件以排查损坏。 3. 如果问题仍然存在,请参阅“获得帮助”。 消息 An over voltage fault detected on power supply .(在电源 设备 上检测到电压过高故障。) LCD 消息 Over voltage fault on PSU . Check PSU.
错误代码 PSU1201 PSU1204 PWR1004 PWR1005 PWR1006 RFM1008 消息信息 详细信息 电源设备的输入类型和额定功率应当相同。 操作 安装匹配的电源设备, 并查阅此手册中的适当配置。 消息 Power supply redundancy is lost.(电源设备冗余缺失。) 详细信息 电源设备尝试在降级状态下运行。系统性能和电源冗余可能降 级或缺失。 操作 检查输入电源。重新安装电源设备。如果问题依然存在,请参 阅“获得帮助”。 消息 The power supplies are not redundant. Insufficient resources to maintain normal operations.(电源设备并非冗余。维持正常运行 的资源不足。) LCD 消息 PSU redundancy degraded. Check PSU cables.
错误代码 RFM1014 RFM1201 RFM2001 RFM2002 RFM2004 152 消息信息 LCD 消息 Removable Flash Media failed. Check SD Card.(可移动的 闪存介质 出现故障。检查 SD 卡。) 详细信息 在 SD 卡读取或写入过程中报告了错误。 操作 重置闪存介质。如果问题仍然存在,请参阅“获得帮助”。 消息 Removable Flash Media is write protected.(可移动的闪存 介质 为写保护状态。) LCD 消息 Removable Flash Media is write protected. Check SD Card.
错误代码 RFM2006 SEC0031 SEC0033 SEL0006 SEL0008 SEL0012 消息信息 操作 重新安装 SD 模块,然后卸下并重新安装 SD 卡。 消息 Internal Dual SD Module is write protected.(内部双 SD 模 块 为写保护。) 详细信息 此模块为写保护。更改可能无法写入到介质。 操作 如果是意外导致,卸下介质并禁用写保护。 消息 The chassis is open while the power is on.(电源开启状态下机箱打 开。) LCD 消息 Intrusion detected. Check chassis cover.(检测到侵入。检查机箱 盖。) 详细信息 机箱打开。系统性能可能降级,安全性可能无法保证。 操作 关闭机箱。检查系统日志。 消息 The chassis is open while the power is off.(电源关闭状态下机箱 打开。) LCD 消息 Intrusion detected.
错误代码 SEL1204 TMP0118 TMP0119 TMP0120 TMP0121 VLT0204 154 消息信息 消息 An unknown system hardware failure detected.(检测到未知系统 硬件故障。) LCD 消息 Unknown system hardware failure.(未知系统硬件故障。) 详细信息 如果系统事件日志初始化失败,将不会捕获平台状态和故障事 件。某些管理软件不会报告平台异常。 操作 将系统重新配置为所支持的最低配置,如果问题仍然存在,请 联系支持部门。 消息 The system inlet temperature is less than the lower warning threshold.(系统进气孔温度低于下限警告阈值。) LCD 消息 System inlet temperature is outside of range.
错误代码 消息信息 LCD 消息 System board voltage is outside of range.(系统板电压超出范 围。) 详细信息 系统硬件检测到电压过高或过低的情况。 如果连续出现多个电压异常,系统可能切换到故障安全模式。 操作 1. 查看系统日志了解电源设备异常。 2. 将系统重新配置为最低配置,检查并重新安装系统电缆。 3.
获得帮助 9 联系 Dell 注: 如果没有活动的 Internet 连接,您可以在购货发票、装箱单、帐单或 Dell 产品目录上查找联系信息。 Dell 提供了若干联机及电话支持和服务选项。服务会因所在国家和地区以及产品的不同而有所差异,您所在的 地区可能不提供某些服务。如要联系 Dell 解决有关销售、技术支持或客户服务问题: 1. 请访问 dell.com/support 2. 选择您的支持类别。 3. 在页面顶部的 Choose a Country/Region(选择国家/地区)下拉式菜单中,验证您所在的国家或地区。 4.