Dell PowerEdge T620 Systems Owner's Manual Regulatory Model: E17S Series Regulatory Type: E17S001
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser l'ordinateur. PRÉCAUTION : Une PRÉCAUTION indique un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessure corporelle ou de mort. Copyright © 2014 Dell Inc. Tous droits réservés.
Contents 1 À propos du système.................................................................................................................. 9 Voyants et fonctions du panneau avant - Mode Tower (tour)..................................................................................9 Voyants et fonctions du panneau avant - Mode rack............................................................................................ 12 Fonctionnalités de l'écran LCD.................................................
Écran Boot Manager (Gestionnaire d'amorçage)............................................................................................39 Menu UEFI Boot (Amorçage UEFI)................................................................................................................... 40 Gestion intégrée du système.................................................................................................................................. 40 Utilitaire iDRAC Settings (Configuration iDRAC)................
Retrait d'un disque dur remplaçable à chaud..................................................................................................62 Installation d'un disque dur remplaçable à chaud...........................................................................................63 Retrait d'un disque dur installé dans un support............................................................................................. 64 Installation d'un disque dur dans un support.....................................
Alimentation de rechange................................................................................................................................90 Retrait d'un bloc d'alimentation en CA.............................................................................................................90 Installation d'un bloc d'alimentation en CA..................................................................................................... 91 Instructions de câblage pour un bloc d'alimentation en CC..
4 Dépannage du système..........................................................................................................134 La sécurité en priorité, pour vous et votre système............................................................................................. 134 Dépannage des échecs de démarrage du système............................................................................................. 134 Dépannage des connexions externes........................................................
Messages d'avertissement.................................................................................................................................. 177 Messages de diagnostic.......................................................................................................................................177 Messages d'alerte................................................................................................................................................ 177 9 Obtenir de l'aide......
À propos du système 1 Voyants et fonctions du panneau avant - Mode Tower (tour) Figure 1.
Figure 2. Voyants et fonctions du panneau avant - Châssis de disque dur de 3,5 pouces Élément Voyant, bouton ou connecteur 1 Lecteur optique (en option) Un lecteur SATA DVD-ROM ou DVD+/-RW en option. 2 Logement de carte de média vFlash Permet d'insérer une carte de support vFlash. 3 Voyant de mise sous tension, bouton d'alimentation Le voyant de mise sous tension s'allume lorsque le système est allumé. Le bouton d'alimentation contrôle l'alimentation fournie au système.
Élément Voyant, bouton ou connecteur Icône Description REMARQUE : Si vous éteignez un ordinateur utilisant un système d'exploitation compatible ACPI en appuyant sur le bouton d'alimentation, le système peut effectuer un arrêt normal avant la mise hors tension de l'ordinateur. 4 Bouton NMI Ce bouton permet de résoudre les erreurs liées aux logiciels ou aux pilotes de périphériques rencontrées avec certains systèmes d'exploitation. Appuyez sur ce bouton à l'aide de la pointe d'un trombone.
Élément Voyant, bouton ou connecteur 11 Disques durs Icône Description Systèmes de disque dur de 3,5 pouces Jusqu'à douze disques durs de 3,5 pouces remplaçables à chaud. Jusqu'à quatre périphériques Dell PowerEdge Express Flash (SSD PCIe). Systèmes de disque dur de 2,5 pouces Jusqu'à 32 disques durs de 2,5 pouces remplaçables à chaud. Jusqu'à quatre disques SSD PCIe.
REMARQUE : Si votre système est en rack, il est préconfiguré avec des équerres et n'est pas doté de pied stabilisateur. Élément Voyant, bouton ou connecteur Icône Description 1, 11 Connecteurs USB (2) Permet de connecter des périphériques USB au système. Les ports sont compatibles USB 2.0. 2 Lecteur optique (en option) Un lecteur SATA DVD-ROM ou DVD+/-RW en option. 3 Baie de disque dur Systèmes de disque dur de 3,5 pouces Jusqu'à douze disques durs de 3,5 pouces remplaçables à chaud.
Élément Voyant, bouton ou connecteur 7 Voyant de mise sous tension, bouton d'alimentation Icône Description Le voyant de mise sous tension s'allume lorsque le système est allumé. Le bouton d'alimentation contrôle l'alimentation fournie au système. REMARQUE : Si vous éteignez un ordinateur utilisant un système d'exploitation compatible ACPI en appuyant sur le bouton d'alimentation, le système peut effectuer un arrêt normal avant la mise hors tension de l'ordinateur.
Figure 4. Fonctionnalités de l'écran LCD Élément Bouton Description 1 Gauche Fait revenir le curseur étape par étape. 2 Sélectionner Permet de sélectionner l'élément de menu mis en surbrillance à l'aide du curseur. 3 Droite Fait avancer le curseur étape par étape. Durant le défilement des messages : • • • • Appuyez une fois pour augmenter la vitesse de défilement. Appuyez de nouveau pour arrêter le défilement. Appuyez une nouvelle fois pour rétablir la vitesse de défilement par défaut.
Option Description iDRAC Sélectionnez DHCP ou Static IP (IP statique) pour configurer le mode réseau. Si Static IP (IP statique) est sélectionné, les champs disponibles sont IP, Subnet (Sub) (sous-réseau) et Gateway (Gtw) (passerelle). Sélectionnez Setup DNS (configuration de DNS) pour activer une DNS et pour afficher les adresses de domaine. Deux entrées de DNS séparées sont disponibles.
Codes des voyants des disques durs Figure 5. Voyants de disque dur 1. voyant d'activité du disque dur (vert) 2. voyant d'état du disque dur (vert et orange) REMARQUE : Si le disque dur est en mode Advanced Host Controller Interface (AHCI), le voyant de l'état (sur la droite) ne fonctionne pas et reste éteint.
Codes des voyants d'état des disques (RAID uniquement) État extinction pendant six secondes Voyants et caractéristiques du panneau arrière Figure 6.
Élément Voyant, bouton ou connecteur Icône Description 1 Logements de carte d'extension PCIe (4) (processeur 1) Permet de connecter jusqu'à deux cartes d'extension PCI Express et deux cartes PERC. 2, 3 Connecteurs Ethernet Deux connecteurs de cartes réseau intégrées 10/100/1000 Mbit/s. 4 Bouton d'identification du système Les boutons d'identification sur les panneaux avant et arrière peuvent être utilisés pour localiser un système particulier à l'intérieur d'un rack.
Élément Voyant, bouton ou connecteur 12 Logements de carte d'extension PCIe pleine hauteur (3) (processeur 2) Icône Description Permet de connecter jusqu'à trois cartes d'extension PCI Express pleine hauteur. Codes des voyants de carte réseau Figure 7. Voyant de la carte réseau 1. voyant de liaison Voyant 2. voyant d'activité Code du voyant Les voyants de liaison La carte réseau n'est pas connectée au réseau.
Figure 8. Voyant d'état du bloc d'alimentation en CA 1. Voyant d'état/poignée du bloc d'alimentation en CA Figure 9. Voyant d'état du bloc d'alimentation en CC 1. Voyant d'état du bloc d'alimentation en CC Comportement du État voyant d'alimentation Éteint Non alimenté. Vert La poignée/le voyant s'allume en vert pour signaler qu'une source d'alimentation valide est connectée au bloc d'alimentation et que celui-ci est opérationnel.
Comportement du État voyant d'alimentation PRÉCAUTION : Les blocs d'alimentation CA prennent en charge les voltages d'entrée de 220 V et de 110 V à l'exception des blocs d'alimentation en titane, qui prennent en charge uniquement 220 V. Lorsque deux blocs d'alimentation identiques reçoivent des voltages d'entrée différents, cela peut engendrer des puissances de sortie différentes et provoquer une non-correspondance.
Utilisation du gestionnaire de configuration du système et d'amorçage 2 La configuration du système vous permet de gérer le matériel du système et de définir les options au niveau du BIOS. Les touches suivantes permettent d'accéder à certaines fonctions au démarrage du système : Touche Description Permet d'accéder à System Setup (Configuration du système). Permet d'entrer dans les Services système, ce qui ouvre le Dell Lifecycle Controller 2 (LC2).
REMARQUE : Par défaut, le texte d'aide du champ sélectionné s'affiche dans le navigateur graphique. Pour afficher le texte d'aide dans le navigateur de texte, appuyez sur la touche . Choix du mode d'amorçage du système Le programme de configuration du système vous permet de spécifier le mode d'amorçage pour l'installation du système d'exploitation : • Le mode d'amorçage du BIOS (par défaut) est l'interface standard d'amorçage au niveau du BIOS.
Barre d'espacement Permet d'étendre ou de réduire la liste déroulante, le cas échéant. Passe à l'objectif suivant. REMARQUE : Seulement pour le navigateur de graphiques standard. <Échap> Passe à la page précédente jusqu'à ce que l'écran principal s'affiche. Si vous appuyez sur <Échap> dans l'écran principal, un message vous invite à enregistrer les modifications non enregistrées et le système redémarre. Affiche le fichier d'aide de System Setup (Configuration du système).
Élément de menu Description SATA Settings (Paramètres SATA) Permet d'afficher les options permettant d'activer ou de désactiver le contrôleur et les ports SATA intégrés. Boot Settings (Paramètres d'amorçage) Permet d'afficher les options pour indiquer le mode d'amorçage (BIOS ou UEFI). Vous permet de modifier les paramètres d'amorçage UEFI et BIOS.
Écran Memory Settings (Paramètres de la mémoire) Élément de menu Description System Memory Size (Taille de la mémoire système) Indique la taille de la mémoire installée dans le système. Type de mémoire du système Indique le type de mémoire installée dans le système. System Memory Speed Indique la vitesse de la mémoire système. Tension de la mémoire du système Indique la tension de la mémoire système. Video Memory Indique la quantité de mémoire vidéo disponible.
Élément de menu Description Disabled (Désactivé), le BIOS n'affiche qu'un processeur logique par cœur. Par défaut, l'option Logical Processor est définie sur Enabled (Activé). QPI Speed (Vitesse QPI) Vous permet de régler les paramètres de débit de données QuickPath Interconnect. Par défaut, l'option QPI Speed (Vitesse QPI) est définie sur Maximum data rate (Débit de données maximal). REMARQUE : L'option QPI Speed (Vitesse QPI) est affichée uniquement lorsque les deux processeurs sont installés.
Élément de menu Description Processor 64-bit Indique si le ou les processeurs prennent en charge les extensions 64 bits. Support (Support des extensions 64 bits par les processeurs) Processor Core Speed (Vitesse du cœur du processeur) Affiche la fréquence maximale du cœur du processeur. Processor Bus Speed Affiche la vitesse de bus des processeurs. (Vitesse de bus du REMARQUE : L'option de la vitesse de bus du processeur s'affiche uniquement lorsque processeur) les deux processeurs sont installés.
Écran Boot Settings (Paramètres d'amorçage) Élément de menu Description Boot Mode (Mode d'amorçage) Vous permet de définir le mode d'amorçage du système. PRÉCAUTION : La permutation du mode d'amorçage peut empêcher le démarrage du système si le système d'exploitation n'a pas été installé selon le même mode d'amorçage. Si le système d'exploitation prend en charge l'UEFI, vous pouvez définir cette option sur UEFI.
Élément de menu Description Internal SD Card Port Active ou désactive le port de la carte SD interne du système. Par défaut, l'option Internal SD (Port de carte SD Card Port (Port de la carte SD interne du système) est réglée sur On (Activé). interne) REMARQUE : Cette option s'affiche seulement si le IDSDM est installé sur la carte système.
Écran Serial Communications (Communications série) Élément de menu Description Serial Communication Vous permet de sélectionner des périphériques de communication série (Périphérique série 1 (Communications et Périphérique série 2) dans le BIOS. La redirection de la console BIOS peut aussi être activée série) et l'adresse du port utilisée peut être spécifiée. Par défaut, l'option Serial Communication (Communication série) est réglée sur On without Console Redirection (Activée sans redirection de console).
Élément de menu Description REMARQUE : Les paramètres suivants ne sont disponibles que lorsque System Profile (Profil du système) est réglé sur Custom (Personnalisé). Gestion de Vous permet de régler la gestion de l'alimentation de l'UC. Par défaut, l'option CPU Power l'alimentation de l'UC Management (Gestion de l'alimentation de l'UC) est réglée sur System DBPM (DAPC) [Modulation biphasée différentielle du système (DAPC)].
Écran System Security (Sécurité du système) Élément de menu Description Intel AES-NI L'option Intel AES-NI améliore la vitesse des applications en réalisant un cryptage et un décryptage à l'aide de l'ensemble des consignes liées à la norme de cryptage avancé, et est réglée sur Enabled (Activé) par défaut. System Password Vous permet de définir le mot de passe système.
Élément de menu Description Bouton d'alimentation Vous permet d'activer ou de désactiver le bouton d'alimentation sur l'avant du système. Par défaut l'option Power Button (Bouton d'alimentation) est réglée sur Enabled (Activé). NMI Button (Bouton INM) Vous permet d'activer ou de désactiver le bouton INM sur l'avant du système. Par défaut l'option NMI Button (Bouton INM) est réglée sur Disabled (Désactivé).
Fonctionnalités de mot de passe du système et de mot de passe de configuration Vous pouvez créer un mot de passe du système et un mot de passe de configuration pour protéger le système. Pour activer la création du mot de passe du système et du mot de passe de configuration, le cavalier de mot de passe doit être activé. Pour obtenir plus d'informations sur les paramètres du cavalier du mot de passe, reportez-vous à la section Paramètres du cavalier de la carte système.
• Le mot de passe peut contenir des nombres de 0 à 9. • Seules les minuscules sont acceptées. • Seuls les caractères spéciaux suivants sont valides : espace, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`). Un message vous invite à ressaisir le mot de passe du système. 6. Saisissez à nouveau le mot de passe du système entré précédemment puis cliquez sur OK. 7.
Protection du système à l'aide d'un mot de passe système REMARQUE : Si vous avez attribué un mot de passe de configuration, le système l'accepte également comme mot de passe du système alternatif. 1. Allumez ou redémarrez le système. 2. Saisissez le mot de passe, puis appuyez sur . Si Password Status (État du mot de passe) indique Locked (Verrouillé), vous devez saisir le mot de passe, puis appuyer sur lorsque le système vous y invite au redémarrage.
Pour accéder au Gestionnaire d'amorçage : 1. Allumez ou redémarrez le système. 2. Appuyez sur dès l'apparition du message suivant : = UEFI Boot Manager (Gestionnaire d'amorçage UEFI) Si le système d'exploitation commence à se charger alors que vous n'avez pas encore appuyé sur , attendez que le système finisse de démarrer, puis redémarrez-le et réessayez.
Élément de menu Description Launch System Setup Vous permet d'accéder au programme de configuration du système. (Démarrer la configuration du système) System Utilities (Utilitaires du système) Vous permet d'accéder à l'explorateur de fichier de mise à jour du BIOS, d'exécuter le programme Dell Diagnostics et de redémarrer le système.
Pour en savoir plus sur l'utilisation d'iDRAC, reportez-vous au iDRAC7 User's Guide (Guide d'utilisation iDRAC7) sous Software → Systems Management → Dell Remote Access Controllers (Logiciel, Gestion des systèmes, Contrôleurs d'accès à distance Dell) à l'adresse suivante : dell.com/support/manuals. Accès à l'utilitaire de configuration iDRAC 1. Activez ou redémarrez le système géré. 2. Appuyez sur pendant l'auto-test de démarrage (POST). 3.
Installation des composants du système 3 Outils recommandés Vous pouvez avoir besoin des outils suivants pour réaliser les procédures décrites dans cette section : • Clé du verrouillage à clé du système • Tournevis cruciforme n° 2 • Tournevis Torx T10 et T15 • Bracelet antistatique connecté à une prise de terre S'ils sont disponibles, vous pouvez utiliser les outils suivants pour l'assemblage des câbles d'un bloc d'alimentation en CC : • Pince AMP 90871-1 ou équivalent • Pince à dénuder les fil
Figure 10. Installation et retrait du cadre avant Retrait du cadre avant 1. Insérez la clé du cadre dans la serrure. 2. Tout en appuyant sur la serrure avec la clé du cadre, faites pivoter la serrure vers la position déverrouillée. 3. Appuyez sur la patte de dégagement située sur le dessus du cadre. 4. Faites pivoter la partie supérieure du cadre en l'éloignant du système. 5. Décrochez les pattes du cadre des fentes situées à l'avant du châssis.
Figure 11. Removing and Installing the System Feet 1. base of the tower 3. screws (4) 2. system feet (4) Installation des pieds du système 1. Posez le système sur le côté sur une surface plane et stable. 2. Fixez les pieds du système à la base de la tour à l'aide de vis. 3. Redressez le système sur une surface plane et stable et faites pivoter les pieds du système vers l'extérieur.
4. Alignez les deux crochets de fixation de l'ensemble de roue arrière avec les deux fentes à la base du châssis puis insérez les crochets dans les fentes. 5. Décalez légèrement l'ensemble de roue arrière vers l'arrière puis fixez l'unité à l'aide de la vis. 6. Alignez les deux crochets de fixation de l'ensemble de roue avant avec les deux fentes à la base du châssis puis insérez les crochets dans les fentes. 7.
3. Vis (2) Ouverture et fermeture du système AVERTISSEMENT : Chaque fois que vous devez soulever le système, demandez de l'aide. Pour éviter les blessures, ne tentez pas de soulever le système par vous-même. AVERTISSEMENT : Ouvrir ou retirer le capot du système lorsque celui-ci est sous tension est dangereux. Vous risqueriez de recevoir une décharge électrique. PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Figure 13. Ouverture et fermeture du système 1. système 2. capot latéral du système 3. loquet de dégagement du capot 4. verrou du loquet de dégagement Fermeture du système 1. Emboîtez le bord inférieur du capot, opposé au loquet de dégagement, dans les fentes correspondantes sur le châssis. 2. Abaissez le capot de manière à le placer sur le châssis. 3. Emboîtez le bord du capot muni du loquet dans le châssis jusqu'à ce qu'il s'enclenche. 4.
Figure 14. À l'intérieur du système 1. Module de ventilation (en option) 2. Support de la carte PCIe 3. Carénage de refroidissement 4. Ventilateurs (2) 5. Dissipateurs de chaleur (2) 6. Support de la carte PCIe 7. Stabilisateurs (4) 8. Barrettes de mémoire DIMM (24) 9. Fond de panier des disques durs Cache du cadre Retrait du cache du cadre PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Figure 15. Retrait et installation du cache du cadre 1. Cache du cadre 2. Languette métallique Installation du cache du cadre PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
Retrait du carénage de refroidissement PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
REMARQUE : Pour que le carénage de refroidissement soit correctement emboîté dans le châssis du système, veillez à ce que les câbles soient correctement acheminés le long des parois du système et fixés à l'aide du support de fixation de câble. 1. Alignez les pattes situées sur le carénage de refroidissement sur les fentes de fixation du châssis. 2. Abaissez doucement le carénage de refroidissement jusqu'à ce qu'il soit correctement inséré dans le châssis. 3.
Figure 17.
Type de barrette de mémoire Barrettes installées/canal Fréquence de fonctionnement (en MT/s) 1,5 V Rangées de barrettes DIMM maximales/canal 1,35 V ECC UDIMM 1 1 333, 1 066 et 800 1 066 et 800 Double rangée 2 1 333, 1 066 et 800 1 066 et 800 Double rangée 1 1 600, 1 333, 1 066 et 800 1 333, 1 066 et 800 Double rangée 1 066 et 800 À quatre rangées Barrette RDIMM 2 LRDIMM 800 1 600, 1 333, 1 066 et 800 1 333, 1 066 et 800 Double rangée 800 800 À quatre rangées 3 1 066 et 800 Non
• Des barrettes de mémoire de différentes tailles peuvent être mélangées tant que les autres règles de population de mémoire sont respectées (par exemple, les barrettes de mémoire de 2 Go et de 4 Go peuvent être mélangées). • Installez quatre barrettes DIMM par processeur (une barrette DIMM par canal) à la fois pour maximiser les performances.
REMARQUE : Les modes Fonctions ECC avancées/Lockstep et Optimisation prennent en charge la mémoire de réserve. Mise en miroir de la mémoire La mise en miroir de la mémoire offre le mode disposant de la plus forte fiabilité des barrettes DIMM comparativement aux autres modes. En effet, il offre une protection contre les incidents non corrigeables sur plusieurs bits. Dans une configuration mise en miroir, la mémoire système totale disponible correspond à la moitié du total de la mémoire physique installée.
Capacité du système (en Go) Taille des barrettes de mémoire DIMM (en Go) Nombre de barrettes de mémoire DIMM Rangée, organisation et fréquence des barrettes de mémoire DIMM Remplissage des logements de barrettes de mémoire DIMM 8 6 2R, x4, 1 333 MT/s, 2R, x4, 1 600 MT/s A1, A2, A3, A4, A5, A6 8 12 2R, x4, 1 333 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12 16 6 2R, x4, 1 333 MT/s, 2R, x4, 1 600 MT/s A1, A2, A3, A4, A5, A6 128 16 8 2R, x4, 1 333 MT/s, 2R, x4, 1 600 MT/s A1, A2,
Capacité du système (en Go) Taille des barrettes de mémoire DIMM (en Go) Nombre de barrettes de mémoire DIMM Rangée, organisation et fréquence des barrettes de mémoire DIMM Remplissage des logements de barrettes de mémoire DIMM B1, B2, B3, B4, B5, B6, B7, B8, B9, B10, B11, B12 16 12 2R, x4, 1 333 MT/s, 2R, x4, 1 600 MT/s A1, A2, A3, A4, A5, A6 B1, B2, B3, B4, B5, B6 256 16 16 2R, x4, 1 333 MT/s, 2R, x4, 1 600 MT/s A1, A2, A3, A4, A5, A6, A7, A8 B1, B2, B3, B4, B5, B6, B7, B8 384 16 24 2R, x
Figure 18. Retrait et installation d'une barrette de mémoire 1. barrette de mémoire 3. repère d'alignement 2. pattes d'éjection du support de barrette de mémoire (2) 6. Installez le carénage de ventilation. 7. Fermez le système. 8. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. Installation de barrettes de mémoire AVERTISSEMENT : Les barrettes de mémoire restent chaudes au toucher quelque temps après l'arrêt du système.
7. Alignez le connecteur latéral de la barrette de mémoire avec le repère d'alignement du support, puis insérez la barrette dans le support. REMARQUE : Le repère d'alignement du support de la barrette de mémoire permet de garantir que la barrette est insérée dans le bon sens. 8. Appuyez sur la barrette de mémoire avec les pouces jusqu'au verrouillage du loquet des leviers du support.
Figure 19. Retrait et installation d'une baie modulaire 1. Baie modulaire 2. Loquet de dégagement Installation d'une baie modulaire PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
Lorsque vous formatez un disque dur, prévoyez assez de temps pour terminer le formatage. Souvenez-vous que des disques durs à capacité élevée peuvent prendre des heures pour se formater. Retrait d'un cache de lecteur de disque dur de 2,5 pouces PRÉCAUTION : Pour assurer un refroidissement correct du système, vous devez installer un cache de disque dur dans toutes les baies de disque dur vacantes. 1. Retirez le cadre avant s'il est installé. 2.
Figure 21. Retrait et installation d'un cache de disque dur de 3,5 pouces 1. cache de disque dur 2. bouton de dégagement Installation d'un cache de lecteur de disque dur de 3,5 pouces 1. Retirez le cadre avant s'il est installé. 2. Insérez le cache de disque dur dans le logement de disque dur jusqu'à ce que le bouton de dégagement s'enclenche. 3. Le cas échéant, installez le cadre avant.
Figure 22. Retrait et installation d'un disque dur remplaçable à chaud 1. bouton de dégagement 3. poignée du support de disque dur 2. disque dur Installation d'un disque dur remplaçable à chaud PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Retrait d'un disque dur installé dans un support 1. Retirez les quatre vis des rails coulissants du support de disque dur. 2. Soulevez le disque dur et retirez-le de son support. Figure 23. Retrait et installation d'un disque dur dans un support 1. support de disque dur 2. disque dur 3. vis (4) Installation d'un disque dur dans un support PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Retrait du cache du lecteur optique slim PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Lecteurs optiques et lecteurs de bande Le système prend en charge l'une des configurations suivantes.
10. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. Figure 25. Retrait et installation du lecteur optique et du lecteur de bande 1. Lecteur optique/lecteur de bande 3. Loquet de dégagement 2. Lecteur optique/lecteur de bande/cache du lecteur REMARQUE : La figure ci-dessous présente un schéma de câblage pour un lecteur optique/lecteur de bande équipé d'un fond de panier x 16.
Figure 26. Câblage : lecteur optique et lecteur de bande 68 1. Adaptateur de bande interne 2. Connecteur mini-SAS/SATA sur l'adaptateur de bande interne 3. Connecteur ODD2/TBU de la carte système 4. Connecteur ODD1/TBU de la carte système 5. Connecteur d'alimentation du fond de panier x16 6. Connecteur de données/d'alimentation du lecteur de bande SAS 7. Connecteur d'alimentation du lecteur optique 2 8. Connecteur de données du lecteur optique 2 9.
Installation du lecteur optique ou du lecteur de bande PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Retrait d'un ventilateur AVERTISSEMENT : Ouvrir ou retirer le capot du système lorsque celui-ci est sous tension est dangereux. Vous risqueriez de recevoir une décharge électrique. Manipulez avec précaution les ventilateurs lorsque vous les retirez ou les installez. PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Installation d'un ventilateur PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Figure 28. Retrait et réinstallation du module de ventilation 1. 2. 3. 4. module de ventilation ventilateurs (4) leviers de dégagement (2) guides d'alignement (2) Installation du module de ventilation (en option) PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
l'option Internal USB Port (Port USB interne) de l'écran Integrated Devices (Périphériques intégrés) de la configuration du système. Pour pouvoir démarrer le système à partir de la clé de mémoire USB, configurez cette dernière avec une image d'amorçage, puis ajoutez la clé à la séquence d'amorçage définie dans le programme de configuration du système. REMARQUE : Pour identifier le connecteur USB interne (INT_USB) sur la carte système, consultez Connecteurs de la carte système.
Retrait du porte-cartes PCIe PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
6. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. Support de la carte GPU (en option) Retrait du support de la carte GPU PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
1. Patte de dégagement 3. Broche de guidage 2. Support de la carte GPU Installation du support de la carte GPU PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
7. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. Cartes d'extension Consignes d'installation des cartes d'extension Tableau 3.
Priorité de la carte Type de carte Priorité du logement Nombre maximal autorisé 9 Non RAID 1, 4, 5, 6, 2, 7 6 10 Adaptateur de bande interne 1, 4, 2 3 11 HIC 4, 5, 7, 2 4 Consignes d'installation d'une carte GPU Pour installer une carte GPU, veuillez respecter les consignes suivantes : • Vérifiez que le kit d'activation GPU est prêt. • Assurez-vous que toutes les cartes GPU sont du même type ou du même modèle. • Chaque carte GPU prend en charge jusqu'à 6 Go de mémoire GDDR5 dédiée.
4. Retirez le porte-cartes PCIe. 5. Le cas échéant, débranchez les câbles de données de la carte PERC et/ou les câbles d'alimentation de la carte GPU. 6. Ouvrez le loquet de la carte PCIe. 7. Tenez la carte par son bord, puis tirez-la pour l'extraire de son connecteur, puis des guide-cartes. 8. Fermez le loquet de la carte PCIe. 9. Réinstallez le porte-cartes PCIe. 10. Refermez le système. 11. Redressez le système. 12.
4. Retirez le porte-cartes PCIe. 5. Le cas échéant, débranchez les câbles connectés à la carte PCIe. 6. Ouvrez le loquet de la carte PCIe situé à côté du logement dans lequel vous souhaitez installer la carte PCIe. 7. Si vous installez une nouvelle carte, retirez la plaque de recouvrement. REMARQUE : Conservez cette plaque au cas où il serait nécessaire de retirer la carte d'extension.
Figure 32. Retrait et installation de la carte GPU 1. 2. 3. 4. 5. 6. carte GPU connecteur de données SLI connecteur d'alimentation pour la carte GPU connecteur d'alimentation pour la carte GPU connecteur x16 volets de la carte PCIe (2) Installation d'une carte GPU PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
9. Connectez les câbles à la carte GPU. 10. Ouvrez les deux volets de la carte PCIe. 11. Réinstallez le porte-cartes PCIe. 12. Refermez le système. 13. Redressez le système. 14. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. Carte SD vFlash La carte SD vFlash est une carte numérique sécurisée (SD/Secure Digital) qui se connecte dans un logement de carte SD vFlash sur le système.
Retrait d'un module SD interne double PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Installation d'un module SD interne double PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
REMARQUE : Pour utiliser une carte SD avec le système, assurez-vous que le port de carte SD interne est activé dans le programme de configuration du système. 1. Éteignez le système et les périphériques connectés, puis débranchez le système de la prise secteur et des périphériques. 2. Ouvrez le système. 3. Le cas échéant, retirez le carénage de refroidissement. 4. Localisez le connecteur de carte SD sur le module SD interne double.
6. Attendez 30 secondes pour que le dissipateur de chaleur se détache du processeur, puis retirez la vis diagonalement opposée à la première vis. 7. Répétez la procédure pour les deux autres vis. 8. Déposez le dissipateur de chaleur. Figure 35. Retrait et installation d'un processeur 1. Dissipateur de chaleur 2. Vis imperdables (4) 3. Processeur 4. Logements (4) PRÉCAUTION : La pression exercée pour maintenir le processeur dans son support est très forte.
Figure 36. Séquence d'ouverture et de fermeture du levier du cadre de protection du processeur 1. Levier de dégagement du support 2. Icône « à fermer en premier » 3. Processeur 4. Levier de dégagement du support 5. Icône « à ouvrir en premier » 11. Maintenez la patte sur le cadre de protection du processeur afin de le redresser et de dégager l'accès au processeur. 12. Extrayez le processeur de son support et laissez le levier d'éjection ouvert en vue de l'installation du nouveau processeur.
Figure 37. Retrait et installation d'un processeur 1. Levier de dégagement de support « à fermer en premier » 2. Coin de la broche 1 du processeur 3. Processeur 4. Levier de dégagement de support « à ouvrir en premier » 5. Support 6. Guide 7. Logement 8. Triangle doré Installation d'un processeur PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
5. Retirez le carénage de refroidissement. 6. Identifiez le support du processeur. 7. Le cas échéant, retirez le cache de protection du support. 8. Avec le pouce, appuyez fermement sur le levier de dégagement du support situé à côté de l'icône « à déverrouiller en premier » 9. et déverrouillez le levier en le poussant vers le bas et en le dégageant de sous la languette. De la même façon, débloquez le levier de dégagement du support situé à côté de l'icône « à fermer en premier ».
• deux modules d'alimentation en CA de 495 W, 750 W ou 1 100 W ou • deux modules d'alimentation en CC de 1 100 W REMARQUE : La puissance nominale du bloc d'alimentation en titane est pour une tension d'entrée allant de 200 VCA à 240 VCA uniquement. Lorsque deux blocs d'alimentation identiques sont installés, la configuration de l'alimentation est redondante (1 + 1).
Figure 38. Retrait et installation d'un bloc d'alimentation en CA 1. connecteur 2. bloc d'alimentation 3. loquet de dégagement 4. poignée du bloc d'alimentation Installation d'un bloc d'alimentation en CA PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Instructions de câblage pour un bloc d'alimentation en CC Votre système prend en charge jusqu'à deux blocs d'alimentation –(48–60) V CC (selon disponibilité). AVERTISSEMENT : Pour les équipements qui utilisent des blocs d'alimentation en CC de -(48 à 60) V, un électricien qualifié doit effectuer toutes les connexions à l'alimentation en CC et aux mises à la terre de sécurité. N'essayez pas d'établir la connexion à une source d'alimentation en CC ou d'installer les mises à la terre par vous-même.
Assemblage et connexion du câble de terre de sécurité AVERTISSEMENT : Pour les équipements qui utilisent des blocs d'alimentation en CC de -(48 à 60) V, un électricien qualifié doit effectuer toutes les connexions à l'alimentation en CC et aux mises à la terre de sécurité. N'essayez pas d'établir la connexion à une source d'alimentation en CC ou d'installer les mises à la terre par vous-même. Tout le câblage électrique doit être conforme aux pratiques et aux codes locaux et nationaux en vigueur.
Assemblage des câbles d'alimentation d'entrée en CC AVERTISSEMENT : Pour les équipements qui utilisent des blocs d'alimentation en CC de -(48 à 60) V, un électricien qualifié doit effectuer toutes les connexions à l'alimentation en CC et aux mises à la terre de sécurité. N'essayez pas d'établir la connexion à une source d'alimentation en CC ou d'installer les mises à la terre par vous-même. Tout le câblage électrique doit être conforme aux pratiques et aux codes locaux et nationaux en vigueur.
Retrait d'un bloc d'alimentation en CC AVERTISSEMENT : Pour les équipements qui utilisent des blocs d'alimentation en CC de -(48 à 60) V, un électricien qualifié doit effectuer toutes les connexions à l'alimentation en CC et aux mises à la terre de sécurité. N'essayez pas d'établir la connexion à une source d'alimentation en CC ou d'installer les mises à la terre par vous-même. Tout le câblage électrique doit être conforme aux pratiques et aux codes locaux et nationaux en vigueur.
Installation d'un bloc d'alimentation en CC AVERTISSEMENT : Pour les équipements qui utilisent des blocs d'alimentation en CC de -(48 à 60) V, un électricien qualifié doit effectuer toutes les connexions à l'alimentation en CC et aux mises à la terre de sécurité. N'essayez pas d'établir la connexion à une source d'alimentation en CC ou d'installer les mises à la terre par vous-même. Tout le câblage électrique doit être conforme aux pratiques et aux codes locaux et nationaux en vigueur.
Figure 42. Retrait et installation d'un cache de bloc d'alimentation 1. cache de bloc d'alimentation Installation du cache de bloc d'alimentation REMARQUE : Le cache de bloc d'alimentation ne doit être installé que sur la seconde baie d'alimentation. Pour installer le cache de bloc d'alimentation, alignez-le sur la baie d'alimentation, puis insérez-le dans le châssis jusqu'à ce qu'il se mette en place en émettant un déclic.
7. Faites glisser puis soulevez la PIB jusqu'à ce que les encoches de la PIB se libèrent des broches du châssis. Figure 43. Retrait et installation de la carte intermédiaire 1. Carte intermédiaire 3. Carte de distribution de l'alimentation 2. Plot d'éjection Retrait de la carte de distribution d'alimentation PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
1. Carte de distribution de l'alimentation 2. Vis (6) Installation de la carte de distribution d'alimentation PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
Installation de la carte intermédiaire PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Figure 44. Retrait et installation de la batterie du système 1. 2. pôle positif du connecteur de la batterie batterie du système 7. Soulevez la batterie hors des pattes de fixation situées sur le pôle négatif du connecteur. 8. Pour installer une nouvelle batterie, maintenez son connecteur en place en appuyant fermement sur le pôle positif de ce dernier. 9. Tenez la batterie pôle positif « + » vers le haut, puis glissez-la sous les pattes de fixation du pôle positif du connecteur. 10.
Retrait du fond de panier des disques durs PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
5. Câble d'alimentation 6. Câble de signal Figure 46. Retrait et installation de fonds de panier SAS/SATA de 3,5 pouces (x8) 1. Connecteur d'alimentation du fond de panier 2. Câble d'alimentation du fond de panier 3. Plot d'éjection 4. Câble de signal 5. Fond de panier 6.
Figure 47. Câblage - Fond de panier SAS/SATA de 3,5 pouces (x8) 104 1. Connecteur d'alimentation du fond de panier 2. Connecteur SAS A du fond de panier 3. Connecteur SAS A de la carte système 4. Connecteur d'alimentation sur la PDB 5. Connecteur de signal de la carte système 6.
Figure 48. Retrait et installation de fonds de panier SAS/SATA de 3,5 pouces (x8) avec une seule carte PERC 1. Connecteur d'alimentation 2. Câble d'alimentation 3. Plot d'éjection 4. Câble SAS B 5. Câble de signal 6. Fond de panier 7.
Figure 49. Câblage - Fonds de panier SAS/SATA de 3,5 pouces (x8) avec une seule carte PERC 106 1. Connecteur d'alimentation du fond de panier 2. Connecteur SAS A du fond de panier 3. Connecteur SAS B de la carte PERC 4. Connecteur SAS A de la carte PERC 5. Connecteur d'alimentation sur la PDB 6. Câble de signal de la carte système 7. Câble de signal du fond de panier 8.
Figure 50. Retrait et installation de fonds de panier SAS/SATA de 3,5 pouces (x8) et de 2,5 pouces (x4) 1. Câble PCIe C 2. Connecteur d'alimentation 3. Câble PCIe D 4. Câble PCIe B 5. Câble de signal 6. Câble PCIe B 7. Câble d'alimentation 8. Plot d'éjection 9. Câble SAS B 10. Câble de signal 11. Câble SAS A 12.
Figure 51. Câblage - Fonds de panier SAS/SATA de 3,5 pouces (x8) et de 2,5 pouces (x4) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
12. 13. 14. 15. 16. 17. 18. Câble SAS B du fond de panier de 3,5 pouces Câble SAS A du fond de panier de 3,5 pouces Câble d'alimentation du fond de panier Connecteur d'alimentation du fond de panier Câble de signal du fond de panier SSD PCIe Câble PCIe D du fond de panier SSD PCIe Câble PCIe C du fond de panier SSD PCIe Figure 52. Retrait et installation de fonds de panier SAS/SATA de 3,5 pouces (x12) 1. Connecteur d'alimentation 2. Câble d'alimentation 3. Câble SAS B 4. Plot d'éjection 5.
Figure 53. Câblage - Fond de panier SAS/SATA de 3,5 pouces (x12) 1. 2. 3. 4. 5. 6. 7. 8.
Figure 54. Retrait et installation de fonds de panier SAS/SATA de 2,5 pouces (x16) 1. Fond de panier 2. Câble de signal 3. Plot d'éjection 4. Câble d'alimentation 5. Connecteur d'alimentation 6. Câble SAS A 7.
Figure 55. Câblage - Fond de panier SAS/SATA de 2,5 pouces (x16) 112 1. Connecteur SAS B de la carte PERC 2. Connecteur SAS A de la carte PERC 3. Connecteur d'alimentation sur la PDB 4. Connecteur de signal de la carte système 5. Connecteur SAS A du fond de panier 6. Connecteur SAS B du fond de panier 7. Connecteur d'alimentation du fond de panier 8.
Figure 56. Retrait et installation de fonds de panier SAS/SATA de 2,5 pouces (x16) et de 2,5 pouces (x4) 1. Fond de panier 2. Câble PCIe D 3. Câble d'alimentation 4. Câble PCIe C 5. Câble PCIe B 6. Câble de signal 7. Câble PCIe A 8. Plot d'éjection 9. Câble de signal 10. Câble d'alimentation 11. Câble SAS A 12. Câble SAS B 13.
Figure 57. Câblage - Fonds de panier SAS/SATA de 2,5 pouces (x16) et de 2,5 pouces (x4) 114 1. Câble PCIe B du fond de panier SSD PCIe 2. Câble PCIe A du fond de panier SSD PCIe 3. Connecteur SAS B de la carte PERC 4. Connecteur SAS A de la carte PERC 5. Connecteur PCIe D de la carte pont PCIe 6. Connecteur PCIe C de la carte pont PCIe 7. Connecteur PCIe B de la carte pont PCIe 8. Connecteur PCIe A de la carte pont PCIe 9.
Figure 58. Retrait et installation de fonds de panier SAS/SATA de 2,5 pouces (x32) avec deux cartes PERC 1. Câble de signal 2. Plot d'éjection 3. Câble d'alimentation 4. Câble SAS A 5. Câble SAS B 6. Câble de signal 7. Câble d'alimentation 8. Câble SAS A 9. Câble SAS B 10.
Figure 59. Câblage - Fonds de panier de 2,5 pouces (x32) avec deux cartes PERC 116 1. Connecteur SAS A sur 2ème carte PERC 2. Connecteur SAS B sur 2ème carte PERC 3. Connecteur SAS B sur 1ère carte PERC 4. Connecteur SAS A sur 1ère carte PERC 5. Connecteur d'alimentation du fond de panier 1 sur le bloc PIB 6. Connecteur d'alimentation du fond de panier 2 sur le bloc PIB 7. Connecteur de signal 1 sur la carte système 8. Connecteur de signal 2 sur la carte système 9.
Figure 60. Retrait et installation de fonds de panier SAS/SATA de 2,5 pouces (x32) avec une seule carte PERC 1. Câble de signal 2. Plot d'éjection 3. Connecteur d'alimentation 4. Câble SAS A 5. Câble SAS B 6. Câble SAS A1 7. Câble SAS B1 8. Câble de signal 9. Câble d'alimentation 10. Câble SAS A1 11. Câble SAS B1 12.
Figure 61. Câblage - Fonds de panier SAS/SATA de 2,5 pouces (x32) avec une seule carte PERC 118 1. Connecteur de signal du fond de panier 1 2. Connecteur SAS B du fond de panier 1 3. Connecteur SAS A du fond de panier 1 4. Connecteur SAS B de la carte PERC 5. Connecteur SAS A de la carte PERC 6. Connecteur d'alimentation du fond de panier 1 sur le bloc PIB 7. Connecteur d'alimentation du fond de panier 2 sur le bloc PIB 8. Connecteur de signal du fond de panier 1 sur la carte système 9.
Installation du fond de panier des disques durs PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
1. Capot supérieur du système 2. Vis (6) Installation du capot supérieur du système REMARQUE : L'utilisation systématique d'un tapis et d'un bracelet antistatiques est recommandée pour manipuler les composants internes du système. 1. Décalez légèrement le capot supérieur vers l'avant du système 2. Alignez le capot supérieur sur le panneau de commande et les encoches situées sur le dessus du châssis. 3. Fixez le capot sur le châssis à l'aide des vis.
REMARQUE : L'utilisation systématique d'un tapis et d'un bracelet antistatiques est recommandée pour manipuler les composants internes du système. 1. Éteignez le système et les périphériques connectés, puis débranchez le système de la prise secteur et des périphériques. 2. Couchez le système sur le côté. 3. Retirez les vis de maintien du capot latéral gauche situées dans le coin inférieur gauche, à l'avant du châssis. 4.
Retrait du panneau de commande - Mode tour PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Installation du panneau de commande - Mode tour PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Figure 64. Retrait et installation du module du panneau de commande - Mode rack 1. Module du panneau de commande 2. Vis Figure 65. Retrait et installation du panneau de commande sur le module du panneau de commande - Mode rack 124 1. Panneau de commande 3. Câble USB du panneau de commande 2.
Installation du panneau de commande - Mode rack PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Figure 66. Retrait et installation de la carte du panneau de commande 1. carte du panneau de commande 2. vis (3) Installation de la carte du panneau de commande PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Retrait du module LCD - Mode tour PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Installation du module LCD - Mode tour PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Figure 68. Retrait et installation du module LCD en mode rack 1. vis 3. module LCD 2. câble LCD Installation du module LCD - Mode rack PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
Retrait du module VGA PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
Installation du module VGA PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
5. Tenez le support de la carte système, soulevez le plot d'éjection bleu et faites glisser la carte système vers l'avant du système. PRÉCAUTION : Ne vous servez pas d'une barrette de mémoire, d'un processeur ou de tout autre composant pour soulever l'assemblage de la carte système. Figure 70. Retrait de la carte système 1. Carte système 2. Plot d'éjection Installation de la carte système PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
h. le support de la carte PCIe 5. Rebranchez tous les câbles à la carte système. Consultez les diagrammes d'acheminement des câbles de ce document. 6. Refermez le système. 7. Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques qui y sont connectés. 8. Importez votre licence iDRAC Enterprise (nouvelle ou déjà existante). Pour plus d'informations, reportez-vous au iDRAC7 User's Guide (Guide d'utilisation iDRAC7) à l'adresse support.dell.com/manuals.
Dépannage du système 4 La sécurité en priorité, pour vous et votre système PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
6. Si le problème persiste, passez à l'étape suivante pour dépanner les autres périphériques USB reliés au système. 7. Mettez hors tension tous les périphériques USB et déconnectez-les du système. 8. Redémarrez le système et, si votre clavier fonctionne, entrez dans le programme de configuration du système. Vérifiez que tous les ports USB sont activés dans l'écran Integrated Devices (Périphériques intégrés), dans les options du programme de configuration du système.
Dépannage d'un système mouillé PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique. Tout dommage causé par une réparation non autorisée par Dell est exclu de votre garantie.
• Carénage de refroidissement • Cartes de montage de carte d'extension (le cas échéant) • Cartes d'extension • Bloc)s) d'alimentation • Module de ventilation, le cas échéant • Ventilateurs de refroidissement • Processeur(s) et dissipateur(s) de chaleur • Barrettes de mémoire • Supports de disque dur 4. • Fond de panier des disques durs Vérifiez que tous les câbles sont connectés correctement. 5. Refermez le système. 6. Exécutez le test de diagnostic approprié.
REMARQUE : Après avoir installé un bloc d'alimentation, patientez quelques secondes pour laisser au système le temps de le reconnaître et de déterminer s'il fonctionne correctement. 2. Si le problème persiste, reportez-vous à la section Obtention d'aide. Dépannage des problèmes de refroidissement PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
4. Entrez dans le programme de configuration du système et vérifiez les paramètres de mémoire du système. Modifiez-les si nécessaire. Si un problème persiste, bien que les paramètres de la mémoire correspondent à la mémoire installée, passez à l'étape 12. 5. Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur. 6. Ouvrez le système. 7. Vérifiez les canaux de mémoire et assurez-vous que l'installation des barrettes est correcte. 8.
9. Refermez le système. Si le problème n'est pas résolu, reportez-vous à la section Obtention d'aide. Dépannage d'une carte SD PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé. N'effectuez que les opérations de dépannage et les petites réparations autorisées par la documentation de votre produit et suivez les instructions fournies en ligne ou par téléphone par l'équipe de maintenance et d'assistance technique.
4. Mettez le système et les périphériques qui y sont connectés hors tension, puis débranchez le système de la prise secteur. 5. Ouvrez le système. 6. Retirez le cadre avant. 7. Vérifiez que le câble d'interface est correctement branché sur le lecteur optique et le contrôleur. 8. Vérifiez que le câble d'alimentation est bien connecté au lecteur. 9. Refermez le système. Si le problème n'est pas résolu, reportez-vous à la section Obtention d'aide.
REMARQUE : Pour dépanner une carte d'extension, consultez sa documentation et celle du système d'exploitation. 1. Exécutez le test de diagnostic approprié. Pour plus d'informations, reportez-vous à la section Utilisation des diagnostics système. 2. Mettez le système et les périphériques qui y sont connectés hors tension, puis débranchez le système de la prise secteur. 3. Ouvrez le système. 4. Vérifiez que chaque carte d'extension est correctement insérée dans son connecteur. 5. Refermez le système.
Utilisation des diagnostics du système 5 Si vous rencontrez un problème avec le système, exécutez les diagnostics du système avant de contacter l'assistance technique de Dell. L'exécution des diagnostics du système permet de tester le matériel du système sans équipement supplémentaire ou risque de perte de données. Si vous ne pouvez pas résoudre vous-même le problème, le personnel de maintenance ou d'assistance peut utiliser les résultats des diagnostics pour vous aider à résoudre le problème.
Exécution des diagnostics intégrés du système Le programme de diagnostics intégrés du système s'exécute à partir de l'écran Dell Lifecycle Controller. PRÉCAUTION : Utilisez les diagnostics intégrés du système pour tester uniquement votre système. L'utilisation de ce programme avec d'autres systèmes peut entraîner des résultats invalides ou des messages d'erreur. 1. Au démarrage du système, appuyez sur . 2.
Cavaliers et connecteurs 6 Positions des cavaliers de la carte système Pour obtenir des informations sur la réinitialisation du cavalier du mot de passe afin de désactiver un mot de passe, reportez-vous à la section Désactivation d'un mot de passe oublié. Tableau 5. Positions des cavaliers de la carte système Cavalier Paramètre PWRD_EN Description La fonction de mot de passe est activée (broches 2–4). (par défaut) La fonction de mot de passe est désactivée (broches 4-6).
Connecteurs de la carte système Figure 71.
Élément Connecteur Description 11 IDRAC_RJ45 Connecteur iDRAC 12 USB 1 à 6 Connecteurs USB 13 FAN2 Connecteur du ventilateur du carénage de refroidissement 14 VGA Connecteur vidéo 15 B12, B8, B4, B11, B7, B3 Supports de barrette de mémoire 16 COM Connecteur série 17 SLOT5 Connecteur 5 de carte PCIe 18 SLOT6 Connecteur 6 de carte PCIe 19 J43 S/O 20 SLOT7 Connecteur 7 de carte PCIe 21 NIP Broche de dégagement de la carte système 22 PIB_CONN Connecteur pour signal PIB 23
Élément Connecteur Description 42 SATA_F Connecteur SATA Désactivation d'un mot de passe oublié Les fonctionnalités logicielles de protection du système comprennent un mot de passe du système et un mot de passe de configuration. Le cavalier de mot de passe permet d'activer ou de désactiver ces mots de passe et d'effacer le(s) mot(s) de passe utilisé(s). PRÉCAUTION : La plupart des réparations ne peuvent être effectuées que par un technicien de maintenance agréé.
Caractéristiques techniques 7 Processeur Type de processeur Un ou deux processeurs Intel Xeon de la famille E5-2600 Bus d’extension Type de bus PCI Express 2ème et 3ème génération Logements d'extension : (Logement 1) Une liaison x8 pleine hauteur, pleine longueur (Logement 2) Une liaison x16 pleine hauteur, pleine longueur (Logement 3) Une liaison x4 pleine hauteur, pleine longueur REMARQUE : Le logement 3 est un logement PCI Express de 2ème génération uniquement.
Mémoire Barrettes LRDIMM Quatre rangées de 32 Go Barrettes RDIMM 2 Go, 4 Go, 8 Go ou 32 Go classés individuellement, par deux ou par quatre 16 Go classés individuellement ou par deux Barrettes UDIMM RAM minimale 2 Go, 4 Go ou 8 Go 2 Go avec un processeur individuel 4 Go avec deux processeurs RAM maximale Barrettes LRDIMM Jusqu'à 768 Go Barrettes RDIMM Jusqu'à 512 Go Barrettes UDIMM Jusqu'à 128 Go Disques Disques durs Systèmes à quatre disques durs Jusqu'à quatre disques durs internes SSD, SAS o
Disques Systèmes à 32 disques durs avec une carte PERC Jusqu'à 32 disques durs internes SAS, SATA, SATA SSD ou Nearline SAS de 2,5 pouces, remplaçables à chaud Logements de disques durs 0 à 7, 8 à 15, 16 à 23, et 24 à 31 Systèmes à 32 disques durs avec deux cartes PERC Jusqu'à 32 disques durs internes SAS, SATA, SATA SSD ou Nearline SAS de 2,5 pouces, remplaçables à chaud Logements de disques durs 0 à 7, 8 à 15, 0 à 7, et 8 à 15 Lecteur optique Un lecteur DVD-ROM ou DVD+/-RW SATA en option REMARQUE : L
Fonctionnement dans la plage de température étendue REMARQUE : Lorsque le système fonctionne dans la plage de température étendue, ses performances peuvent s'en voir affectées. REMARQUE : En cas de fonctionnement dans la plage de température étendue, des avertissements de température ambiante peuvent être reportés sur l'écran LCD et dans le journal des événements système.
Conditions environnementales REMARQUE : Pour en savoir plus sur les mesures d'exploitation liées à différentes configurations particulières, rendez-vous sur dell.com/environmental_datasheets.
Conditions environnementales Contamination particulaire REMARQUE : Cette section définit les limites de prévention des dommages causés aux équipements IT et/ou des malfonctions issus de contaminations particulaires ou gazeuses.
Messages système 8 Messages LCD REMARQUE : Seulement applicable si votre système a un affichage d'écran LCD. Les messages affichés sur l'écran LCD sont des messages textes brefs qui renvoient à des événements enregistrés dans le journal des événements système (SEL). Pour plus d'informations sur le SEL et sur les paramètres de configuration de la gestion du système, reportez-vous à la documentation du logiciel de gestion des systèmes.
REMARQUE : Si vous recevez du système un message qui n'est pas répertorié dans la liste ci-dessous, vérifiez la documentation de l'application que vous utilisiez au moment où le message est apparu. Vous pouvez aussi vous reporter à la documentation du système d'exploitation pour obtenir une explication du message et l'action conseillée. REMARQUE : Dans certains messages, un composant système particulier est identifié par nom (« »), numéro de composant (« ») or emplacement (« baie »).
Code d'erreur ASR0001 ASR0002 ASR0003 BAT0002 BAT0017 Informations des messages Action Vérifiez le journal des événements du système d'exploitation, de l'application, du matériel et du système pour trouver des événements de l'exception. Message The watchdog timer reset the system. (Le registre d'horloge de la surveillance a réinitialisé le système.) Détails Le système d'exploitation ou une application n'a pas réussi à communiquer au cours du délai imparti. Le système a été réinitialisé.
Code d'erreur CPU0000 CPU0001 CPU0005 158 Informations des messages Message sur l'écran LCD The battery has failed. Check battery. (La batterie est défaillante. Vérifiez la batterie.) Détails La batterie est soit manquante, défectueuse ou incapable de charger suite à des problèmes thermiques. Action Vérifiez les ventilateurs du système. Si le problème persiste, reportezvous à la section Obtention d'aide. Message CPU has an internal error (IERR).
Code d'erreur CPU0010 CPU0023 CPU0204 Informations des messages Action Examinez les caractéristiques techniques des types de processeurs pris en charge. Message CPU is throttled. (Les performances de l'UC sont réduites.) Détails Les performances de l'UC sont réduites suite à des conditions thermiques ou d'alimentation. Action Examinez les journaux système pour détecter des exceptions d'alimentation ou thermiques. Message CPU is absent. (L'UC est absente.
Code d'erreur CPU0701 Informations des messages Réappliquez la puissance d'entrée et allumez le système. 4. Si le problème persiste, reportez-vous à la section Obtention d'aide. CPU protocol error detected. (Détection d'une erreur de protocole de l'UC .) Message sur l'écran LCD CPU protocol error detected. Power cycle system. (Détection d'une erreur de protocole de l'UC . Coupez puis rétablissez l'alimentation du système.
Code d'erreur CPU0703 Informations des messages Message CPU bus initialization error detected. (Détection d'une erreur d'initialisation du bus de l'UC.) Message sur l'écran LCD CPU bus initialization error detected. Power cycle system. (Détection d'une erreur d'initialisation du bus de l'UC. Coupez puis rétablissez l'alimentation du système.) Détails Le journal des événements système et les journaux du système d'exploitation peuvent indiquer que l'exception est externe au processeur.
Code d'erreur VENTILATEUR0001 VENTILATEUR1201 HWC1001 HWC2003 HWC2005 162 Informations des messages Action Retirez puis installez de nouveau le bloc d'alimentation. Si le problème persiste, reportez-vous à la section Obtention d'aide. Message CPU temperature is less than the lower warning threshold. (La température de l'UC est inférieure au seuil d'avertissement minimal.) Message sur l'écran LCD Les rotations par minute du ventilateur sont hors d'atteinte.
Code d'erreur MEM0000 MEM0001 MEM0007 Informations des messages Message sur l'écran LCD La connexion du câble de la carte système est en panne. Vérifiez la connexion. Détails Le câble peut être nécessaire pour un fonctionnement correct. Les fonctionnalités du système peuvent être dégradées. Action Vérifiez si le câble est présent, ensuite réinstallez-le ou reconnectezle. Message Persistent correctable memory errors detected on a memory device at location(s) .
Code d'erreur MEM0701 MEM0702 MEM1205 MEM1208 164 Informations des messages Message Correctable memory error rate exceeded for . (Seuil d'erreurs de mémoire corrigibles dépassé pour .) Détails La mémoire peut ne pas être opérationnelle. Il s'agit d'un premier indicateur d'une éventuelle erreur non corrigible future. Action Réinsérez les barrettes de mémoire. Si le problème persiste, reportezvous à la section Obtention d'aide .
Code d'erreur MEM8000 PCI1302 PCI1304 PCI1308 Informations des messages Message Correctable memory error logging disabled for a memory device at location . (Désactivation de la journalisation des erreurs de la mémoire permanente corrigeable pour un périphérique mémoire de l'emplacement .) Message sur l'écran LCD SBE log disabled on . Re-seat memory. (Désactivation du journal des erreurs portant sur un seul bit sur . Réinsérez la mémoire.
Code d'erreur PCI1320 PCI1342 PCI1348 PCI1360 166 Informations des messages Action Coupez puis rétablissez l'alimentation, mettez à jour les pilotes du composant. Si le périphérique est amovible, réinstallez le périphérique. Message A bus fatal error was detected on a component at bus devicefunction . (Détection d'une erreur fatale de bus sur un composant du bus du périphérique de la fonction .
Code d'erreur PDR0001 PDR1016 PST0128 PST0129 Informations des messages Message sur l'écran LCD Bus fatal error on slot . Re-seat PCI card. (Erreur fatale de bus du logement . Réinsérez la carte PCI.) Détails Les performances du système peuvent être dégradées ou le système peut ne pas fonctionner. Action Coupez puis rétablissez l'alimentation, mettez à jour les pilotes du composant. Si le périphérique est amovible, réinstallez le périphérique.
Code d'erreur PSU0001 PSU0002 PSU0003 PSU0006 168 Informations des messages Détails Le BIOS du système a détecté la mémoire mais a été incapable de configurer la mémoire pour le fonctionnement du système. Action Comparez l'installation de la mémoire du système avec les configurations de mémoire du système prises en charge. Message Power supply failed. (Panne du bloc d'alimentation .) Message sur l'écran LCD PSU failed. Check PSU. (Panne du bloc d'alimentation .
Code d'erreur PSU0016 Informations des messages Action Installez des blocs d'alimentation correspondants et vérifiez la configuration à utiliser dans ce manuel. Message Power supply is absent. (Le bloc d'alimentation est manquant.) Message sur l'écran LCD PSU is absent. Check PSU. (Le bloc d'alimentation est manquant. Vérifiez le bloc d'alimentation.) Détails Le bloc d'alimentation a été retiré ou est défectueux. Action PSU0031 PSU0032 PSU0033 1.
Code d'erreur PSU0034 Informations des messages Détails Les performances du système peuvent être dégradées. Action Vérifiez l'environnement de fonctionnement système, notamment le débit d'air et la température d'entrée. Recherchez une panne de température et de composant thermique dans les journaux du système. Message An under voltage fault detected on power supply . (Un défaut de sous-tension a été détecté sur l'alimentation ).
Code d'erreur PSU0037 PSU0076 PSU1201 PSU1204 Informations des messages Message Fan failure detected on power supply . (Une panne de ventilateur a été détectée sur l'alimentation .) Message sur l'écran LCD Fan failure detected on PSU . Check PSU. (Une panne de ventilateur a été détectée sur le . Vérifiez le PSU). Action Vérifiez s'il y a un blocage de ventilateur. Si le problème persiste, reportez-vous à la section Obtention d'aide.
Code d'erreur PWR1004 PWR1005 PWR1006 RFM1008 RFM1014 172 Informations des messages Message The system performance degraded because power capacity has changed. (Dégradation des performances du système à cause d'une modification des capacités d'alimentation.) Détails Le système peut s'éteindre ou fonctionner dans un état dégradé. Action Examinez le journal des événements pour détecter des pannes de blocs d'alimentation.
Code d'erreur RFM1201 RFM2001 RFM2002 RFM2004 Informations des messages Message sur l'écran LCD Removable Flash Media is write protected. Check SD Card. (Le support flash amovible est protégé en écriture. Vérifiez la carte SD.) Détails La carte est protégée en écriture par un loquet sur la carte SD. Une carte protégée en écriture ne peut pas être utilisée. Action Si cela n'est pas prévu, retirez le support et désactivez la protection en écriture.
Code d'erreur RFM2006 SEC0031 SEC0033 SEL0006 SEL0008 174 Informations des messages Message Internal Dual SD Module is write protected. (Le module SD double interne est protégé en écriture.) Détails Le module est protégé en écriture. Les modifications ne peuvent être écrites sur le support. Action Si cela n'est pas prévu, retirez le support et désactivez la protection en écriture. Message The chassis is open while the power is on.
Code d'erreur SEL0012 SEL1204 TMP0118 TMP0119 Informations des messages Message Could not create or initialize the system event log. (Impossible de créer ou d'initialiser le journal des événements système.) Détails Si le journal des événements système n'arrive pas à s'initialiser, l'état de la plateforme et les événements ne peuvent pas être enregistrés. Certains logiciels de gestion ne rapportent pas les exceptions de plateforme. Action Redémarrez le contrôleur de gestion ou le contrôleur iDRAC.
Code d'erreur TMP0120 TMP0121 VLT0204 Informations des messages Message The system inlet temperature is greater than the upper warning threshold. (La température d'entrée du système est supérieure au seuil d'avertissement maximal.) Message sur l'écran LCD System inlet temperature is outside of range. (La température d'entrée du système ne se trouve pas dans les limites.) Détails La température de l'air ambiant est trop chaude ou un ou plusieurs ventilateurs sont en panne.
Messages d'avertissement Un message d'avertissement vous alerte des éventuels problèmes et invites auxquels vous devez répondre avant que le système ne poursuive sa tâche. Par exemple, avant de formater un disque dur, un message vous avertit que vous pouvez perdre toutes les données se trouvant sur le disque dur. Les messages d'avertissement interrompent généralement la tâche et demande que vous répondiez en saisissez o (oui) ou n (non).
Obtenir de l'aide 9 Contacter Dell REMARQUE : Si vous ne disposez pas d'une connexion Internet, les informations de contact figurent sur la facture d'achat, le borderau de colisage, la facture le catalogue des produits Dell. Dell propose diverses options d'assistance et de maintenance en ligne et téléphonique. Ces options varient en fonction du pays et du produit et certains services peuvent ne pas être disponibles dans votre région Pour contacter le service commercial, technique ou client de Dell : 1.