Dell PowerEdge T630 Owner's Manual Regulatory Model: E25S Series Regulatory Type: E25S001 August 2020 Rev.
Contents Chapter 1: Dell PowerEdge T630 server overview ......................................................................... 8 Supported configurations for the PowerEdge T630 server......................................................................................8 Front panel...........................................................................................................................................................................10 2.5-inch hard drive chassis..........................
Options to set up iDRAC IP address.......................................................................................................................39 Log in to iDRAC................................................................................................................................................................. 40 Options to install the operating system.......................................................................................................................
Mode-specific guidelines........................................................................................................................................... 89 Sample memory configurations................................................................................................................................90 Removing memory modules......................................................................................................................................
Removing a processor.............................................................................................................................................. 132 Installing a processor................................................................................................................................................ 135 Installing a heat sink..................................................................................................................................................
Troubleshooting the video subsystem........................................................................................................................195 Troubleshooting a USB device..................................................................................................................................... 195 Troubleshooting a serial input and output device....................................................................................................196 Troubleshooting a NIC..............
1 Dell PowerEdge T630 server overview The Dell PowerEdge T630 rackable tower servers support up to: ● Intel Xeon E5-2600 v4 processors ● 24 DIMMs ● Eighteen 3.5 inch hard drives ● Four Dell PowerEdge Express Flash devices ● Thirty two 2.5 inch hard drives NOTE: The T630 systems support only internal, hot-swappable hard drives.
Figure 1.
Front panel 2.5-inch hard drive chassis Figure 2. Front panel— 2.5-inch hard drive chassis 1. SD vFlash card slot 2. power button 3. NMI button 4. System identification button 5. LCD menu buttons 6. Information tag 7. LCD panel 8. iDRAC Direct port 9. VGA connector 10. USB connector 11. Optical drive or tapedrive bay 12.
Table 1. Front panel button and connector description Item Button, or connector Icon Description 1 SD vFlash card slot Use this to insert a vFlash media card. The vFlash media card is an SD card that extends the functionalities of the iDRAC enterprise card. 2 Power-on indicator, power button The power-on indicator turns on when the system power is on. The power button controls the power supply output to the system.
Table 1. Front panel button and connector description (continued) Item Button, or connector Icon Description 10 USB connector Use this to connect USB devices to the system. This port is USB 3.0-compliant. 11 Optical drive or tape-drive bay Use this to install optical drives or tape drives. For more information on supported optical drives and tape drives, see the section Optical drives and tape drives section. 12 Physical drives Up to thirty two 2.
Figure 3. Front panel— 3.5-inch hard drive plus four PCIe SSD chassis 1. SD vFlash card slot 2. power button 3. NMI button 4. System identification button 5. LCD menu buttons 6. Information tag 7. LCD panel 8. iDRAC Direct port 9. VGA connector 10. USB connector 11. Optical drive or tapedrive bay 12. Flex Bay 13. PCIe SSDs 14. 3.
Table 2. Front panel button and connector description Item Button, or connector Icon Description 1 SD vFlash card slot Use this to insert a vFlash media card. The vFlash media card is an SD card that extends the functionalities of the iDRAC enterprise card. 2 Power-on indicator, power button The power-on indicator turns on when the system power is on. The power button controls the power supply output to the system.
Table 2. Front panel button and connector description (continued) Item Button, or connector Icon Description 10 USB connector Use this to connect USB devices to the system. This port is USB 3.0-compliant. 11 Optical drive or tape-drive bay Use this to install optical drives or tape drives. For more information on supported optical drives and tape drives, see the section Optical drives and tape drives section.
Viewing Home screen The Home screen displays user-configurable information about the system. This screen is displayed during normal system operation when there are no status messages or errors. When the system turns off and there are no errors, LCD enters the standby mode after five minutes of inactivity. Press any button on the LCD to turn it on. Steps 1. To view the Home screen, press one of the three navigation buttons (Select, Left, or Right). 2.
Back panel Figure 5. Back panel features 1. PCIe expansion card slots (3) (processor 1) 2. Ethernet connectors 3. System identification connector 4. System identification button 5. iDRAC Enterprise port 6. Power supply (PSU1) 7. USB port(6) 8. Video connector 9. Serial connector 11. Full-height PCIe expansion card slots (processor 2) 10. Power supply (PSU2) Table 4.
Table 4. Back panel indicator, button, or Connector description (continued) Item Indicator, Button, or Connector Icon Description system status indicator on the back flash until one of the buttons is pressed again. Press to toggle the system ID on and off. If the system stops responding during POST, press and hold the system ID button for more than five seconds to enter the BIOS progress mode. To reset iDRAC (if not disabled in F2 iDRAC setup), press and hold for more than 15 seconds.
Table 5. Diagnostic indicators (continued) Icon Description Condition Corrective action Hard drive indicator The indicator flashes amber if there is a hard drive error. Check the System Event Log to determine the hard drive that has an error. Run the appropriate Online Diagnostics test. Restart the system and run embedded diagnostics (ePSA). If the hard drives are configured in a RAID array, restart the system and enter the host adapter configuration utility program.
Table 6. NIC indicators Convention Status Condition A Link and activity indicators are off. The NIC is not connected to the network. B Link indicator is green. The NIC is connected to a valid network at its maximum port speed (1 Gbps or 10 Gbps). C Link indicator is amber The NIC is connected to a valid network at less than its maximum port speed. D Activity indicator is flashing. green Network data is being sent or received.
Table 7. AC PSU status indicators (continued) Convention Power indicator pattern Condition CAUTION: When correcting a PSU mismatch, replace only the PSU with the flashing indicator. Swapping the PSU to make a matched pair can result in an error condition and unexpected system shutdown. To change from a high output configuration to a low output configuration or vice versa, you must turn off the system.
Table 8. DC PSU status indicators (continued) Convention Power indicator pattern Condition change from a High Output configuration to a Low Output configuration or vice versa, you must turn off the system. CAUTION: AC PSU support both 220 V and 110 V input voltages with the exception of Titanium PSU, which support only 220 V. When two identical PSU receive different input voltages, they can output different wattages, and trigger a mismatch.
Table 9. Hard drive indicator codes (continued) Drive-status indicator pattern Condition NOTE: The drive status indicator remains off until all hard drives are initialized after the system is turned on. Drives are not ready for insertion or removal during this time.
2 Converting the system from tower mode to rack mode Your system can be converted from the tower mode to the rack mode.
Figure 10. Installing the rack slide cover a. rack slide cover b. system chassis Figure 11. Removing the rack slide cover a. rack slide cover b. system chassis 4. Install the control panel assembly. For more information, see Installing control panel assembly. 5. Attach the mylar to cover the openings on the chassis where the system rear feet were installed in the tower mode. See the following figure for more information.
Figure 12. Attaching the mylar cover a. marking on chassis b. mylar cover 6. Install the system cover. 7. Install the rack ears by performing the following steps: a. Align the three screw holes on the rack ears with the screw holes on the top and the bottom of system. b. Install the three screws using a Phillips #2 screwdriver.
Figure 13. Removing the rack ears a. screw (6) b. rack ear (2) c. system in rack mode 8. Install the system in the rack. For more information, see the Rack Installation Guide that is shipped with your system.
3 Documentation resources This section provides information about the documentation resources for your system. To view the document that is listed in the documentation resources table: ● From the Dell EMC support site: 1. Click the documentation link that is provided in the Location column in the table. 2. Click the required product or product version. NOTE: To locate the product name and model, see the front of your system. 3. On the Product Support page, click Manuals & documents.
Table 10. Additional documentation resources for your system (continued) Task Document Location To identify the version of iDRAC available on your system, on the iDRAC web interface, click ? > About. For information about installing the www.dell.com/ operating system, see the operatingsystemmanuals operating system documentation. Managing your system For information about updating drivers and firmware, see the Methods to download firmware and drivers section in this document. www.dell.
Table 10. Additional documentation resources for your system (continued) Task Document Location components, see the Error Code Lookup. Troubleshooting your For information about identifying system and troubleshooting the PowerEdge server issues, see the Server Troubleshooting Guide. 30 Documentation resources www.dell.
4 Technical specifications The technical and environmental specifications of your system are outlined in this section.
Chassis dimensions Figure 14. Details the dimensions of Dell PowerEdge T630 system Table 11. The dimensions of Dell PowerEdge T630 system System Xa Xb Ya Yb Yc Za with bezel Za without bezel Zb* Zc PowerEdg e T630 304.5 217.9 434.5 443.5 471.5 15.9 0.0 659.9 692.
Chassis weight Table 12. Chassis weight PowerEdge T630 Maximum weight 3.5 inch hard-drive chassis 49.65 kg 2.5 inch hard-drive chassis 42.36 kg Processor specifications The PowerEdge T630 system supports up to two Intel Xeon E5-2600 v4 or Xeon E5-2600 v3 product family processors. PSU specifications The PowerEdge T630 system supports up to two AC or DC redundant power supply units (PSUs). Table 13.
Table 14.
● Up to thirty-two 2.5 inch, internal, hot-swappable SAS, SATA, SATA SSD, or Nearline SAS hard drives. Hard-drive slots 0 through 7, 8 through 15, 0 through 7, and 8 through 15. Optical drive The PowerEdge T630 system supports one optional SATA DVD-ROM drive or DVD+/-RW drive or One optional slim SATA DVDROM drive or DVD +/-RW drive. NOTE: DVD devices are data only. Ports and connectors specifications Serial connector The serial connector connects a serial device to the system.
Video specifications The PowerEdge T630 system supports Integrated Matrox G200 with iDRAC8 and 16 MB application memory. Table 17.
Table 21. Maximum shock specifications (continued) Maximum vibration Specifications Storage Six consecutively executed shock pulses in the positive and negative x, y, and z axes (one pulse on each side of the system) of 71 G for up to 2 ms. Table 22. Maximum altitude specifications Maximum altitude Specifications Operating 30482000 m (10,0006560 ft) Storage 12,000 m (39,370 ft) Table 23.
Table 25. Gaseous contamination specifications Gaseous contamination Specifications Copper coupon corrosion rate <300 Å/month per Class G1 as defined by ANSI/ISA71.04-1985. Silver coupon corrosion rate <200 Å/month as defined by AHSRAE TC9.9. NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity. Expanded operating temperature Table 26.
5 Initial system setup and configuration Topics: • • • • • Setting up your system iDRAC configuration Log in to iDRAC Options to install the operating system Downloading the drivers and firmware Setting up your system Complete the following steps to set up your system: Steps 1. Unpack the system. 2. Install the system into the rack. For more information about installing the system into the rack, see your system Rack Installation Placemat at Dell.com/poweredgemanuals. 3.
NOTE: To access iDRAC, ensure that you install the iDRAC port card or connect the network cable to the Ethernet connector 1 on the system board. NOTE: Ensure that you change the default user name and password after setting up the iDRAC IP address. Log in to iDRAC You can log in to iDRAC as: ● iDRAC user ● Microsoft Active Directory user ● Lightweight Directory Access Protocol (LDAP) user The default user name and password are root and calvin. You can also log in by using Single Sign-On or Smart Card.
4. Download the drivers to a USB drive, CD, or DVD.
6 Pre-operating system management applications You can manage basic settings and features of a system without booting to the operating system by using the system firmware.
Viewing System Setup To view the System Setup screen, perform the following steps: Steps 1. Turn on, or restart your system. 2. Press F2 immediately after you see the following message: F2 = System Setup NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again.
Miscellaneous Settings on page 64 iDRAC Settings utility on page 65 Device Settings on page 66 Related tasks System Security Settings details on page 48 Viewing System BIOS on page 44 Viewing System BIOS To view the System BIOS screen, perform the following steps: Steps 1. Turn on, or restart your system. 2.
Related references System BIOS on page 43 Related tasks Viewing System BIOS on page 44 Boot Settings You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to specify the boot order.
Option Description CAUTION: Switching the boot mode may prevent the system from booting if the operating system is not installed in the same boot mode. If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS allows compatibility with non-UEFI operating systems. This option is set to BIOS by default. NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu. Setting this field to BIOS disables the UEFI Boot Settings menu.
Related tasks Boot Settings details on page 45 Viewing Boot Settings on page 45 Changing the boot order About this task You may have to change the boot order if you want to boot from a USB key or an optical drive. The following instructions may vary if you have selected BIOS for Boot Mode. Steps 1. On the System Setup Main Menu screen, click System BIOS > Boot Settings. 2. Click BIOS/UEFI Boot Settings > Boot Sequence. 3.
3. On the System Setup Main Menu screen, click System BIOS. 4. On the System BIOS screen, click System Security.
Option Description Secure Boot Policy Summary Specifies the list of certificates and hashes that secure boot uses to authenticate images. Related references System Security on page 47 Related tasks Viewing System Security on page 47 Secure Boot Custom Policy Settings Secure Boot Custom Policy Settings is displayed only when Secure Boot Policy is set to Custom. Viewing Secure Boot Custom Policy Settings To view the Secure Boot Custom Policy Settings screen, perform the following steps: Steps 1.
Related tasks Viewing System Information on page 50 Viewing System Information To view the System Information screen, perform the following steps: Steps 1. Turn on, or restart your system. 2. Press F2 immediately after you see the following message: F2 = System Setup NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then restart your system and try again. 3. On the System Setup Main Menu screen, click System BIOS. 4.
Related tasks Viewing System Information on page 50 Creating a system and setup password Prerequisites Ensure that the password jumper is enabled. The password jumper enables or disables the system password and setup password features. For more information, see the System board jumper settings section. NOTE: If the password jumper setting is disabled, the existing system password and setup password are deleted and you need not provide the system password to boot the system. Steps 1.
NOTE: If an incorrect system password is typed, the system displays a message and prompts you to reenter your password. You have three attempts to type the correct password. After the third unsuccessful attempt, the system displays an error message that the system has stopped functioning and must be turned off. Even after you turn off and restart the system, the error message is displayed until the correct password is entered.
Memory Settings You can use the Memory Settings screen to view all the memory settings and enable or disable specific memory functions, such as memory testing and node interleaving. Related references Memory Settings details on page 53 System BIOS on page 43 Related tasks Viewing Memory Settings on page 53 Viewing Memory Settings To view the Memory Settings screen, perform the following steps: Steps 1. Turn on, or restart your system. 2.
Option Description NOTE: The Memory Operating Mode option can have different default and available options based on the memory configuration of your system. NOTE: The Dell Fault Resilient Mode option establishes an area of memory that is fault resilient. This mode can be used by an operating system that supports the feature to load critical applications or enables the operating system kernel to maximize system availability.
Processor Settings details About this task The Processor Settings screen details are explained as follows: Option Description Logical Processor Enables or disables the logical processors and displays the number of logical processors. If this option is set to Enabled, the BIOS displays all the logical processors. If this option is set to Disabled, the BIOS displays only one logical processor per core. This option is set to Enabled by default.
Option Description Option Description Family-ModelStepping Specifies the family, model, and stepping of the processor as defined by Intel. Brand Specifies the brand name. Level 2 Cache Specifies the total L2 cache. Level 3 Cache Specifies the total L3 cache. Number of Cores Specifies the number of cores per processor.
SATA Settings details About this task The SATA Settings screen details are explained as follows: Option Description Embedded SATA Enables the embedded SATA option to be set to Off, ATA, AHCI, or RAID modes. This option is set to AHCI by default. Security Freeze Lock Sends Security Freeze Lock command to the Embedded SATA drives during POST. This option is applicable only for ATA and AHCI modes. Write Cache Enables or disables the command for Embedded SATA drives during POST.
Option Description Port E Sets the drive type of the selected device. For Embedded SATA settings in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS support. For AHCI or RAID mode, BIOS support is always enabled. Port F Option Description Model Specifies the drive model of the selected device. Drive Type Specifies the type of drive attached to the SATA port. Capacity Specifies the total capacity of the hard drive.
Option Description Port J Sets the drive type of the selected device. For Embedded SATA settings in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF to turn off BIOS support. For AHCI or RAID mode, BIOS support is always enabled. Option Description Model Specifies the drive model of the selected device. Drive Type Specifies the type of drive attached to the SATA port. Capacity Specifies the total capacity of the hard drive.
Integrated Devices details About this task The Integrated Devices screen details are explained as follows: Option Description USB 3.0 Setting Enables or disables the USB 3.0 support. Enable this option only if your operating system supports USB 3.0. If you disable this option, devices operate at USB 2.0 speed. USB 3.0 is enabled by default. User Accessible USB Ports Enables or disables the USB ports.
Related tasks Viewing Integrated Devices on page 59 Serial Communication You can use the Serial Communication screen to view the properties of the serial communication port. Related references System BIOS on page 43 Related tasks Serial Communication details on page 61 Viewing Serial Communication on page 61 Viewing Serial Communication To view the Serial Communication screen, perform the following steps: Steps 1. Turn on, or restart your system. 2.
Option Description within the BIOS setup utility may not always revert the serial MUX setting to the default setting of Serial Device 1. External Serial Connector Enables you to associate the External Serial Connector to Serial Device 1, Serial Device 2, or the Remote Access Device by using this option. NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by SOL, configure the same port address for console redirection and the serial device.
4. On the System BIOS screen, click System Profile Settings. Related references System Profile Settings on page 62 Related tasks System Profile Settings details on page 63 System Profile Settings details About this task The System Profile Settings screen details are explained as follows: Option Description System Profile Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS automatically sets the rest of the options.
Option Description Cores for Processor 1 Controls the number of turbo boost enabled cores for processor 1. The maximum number of cores is enabled by default. Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system profiles, except Custom by default. NOTE: This option can be disabled only if the C States option in the Custom mode is set to disabled.
Miscellaneous Settings details About this task The Miscellaneous Settings screen details are explained as follows: Option Description System Time Enables you to set the time on the system. System Date Enables you to set the date on the system. Asset Tag Specifies the asset tag and enables you to modify it for security and tracking purposes. Keyboard NumLock Enables you to set whether the system boots with the NumLock enabled or disabled. This option is set to On by default.
Related tasks Entering the iDRAC Settings utility on page 66 Changing the thermal settings on page 66 Entering the iDRAC Settings utility Steps 1. Turn on or restart the managed system. 2. Press F2 during Power-on Self-test (POST). 3. On the System Setup Main Menu page, click iDRAC Settings. The iDRAC Settings screen is displayed.
NOTE: Certain platform configurations may not support the full set of features provided by the Dell Lifecycle Controller. For more information about setting up the Dell Lifecycle Controller, configuring hardware and firmware, and deploying the operating system, see the Dell Lifecycle Controller documentation at Dell.com/idracmanuals. Related references Dell Lifecycle Controller on page 66 Boot Manager The Boot Manager screen enables you to select boot options and diagnostic utilities.
Related references Boot Manager on page 67 Related tasks Viewing Boot Manager on page 67 One-shot BIOS boot menu One-shot BIOS boot menu enables you to select a boot device to boot from. Related references Boot Manager on page 67 System Utilities System Utilities contains the following utilities that can be launched: ● Launch Diagnostics ● BIOS/UEFI Update File Explorer ● Reboot System NOTE: Depending on the boot mode selected, you might have BIOS or UEFI Update File Explorer.
7 Installing and removing system components This section provides information about installing and removing the system components.
NOTE: For specific caution statements and procedures, see the rack installation documentation for your system at Dell.com/poweredgemanuals. For complete safety and regulatory information, see the safety instructions that shipped with your system. Observe the following precautions for stability and safety of the system in rack mode: ● Before installing your equipment in a rack, install the front and side rack stabilizers. Failure to install the stabilizers can cause the rack to tip over.
Recommended tools You need the following tools to perform the removal and installation procedures: ● Key to the bezel lock. The key is needed only if your system includes a bezel. ● Phillips #2 screwdriver ● Wrist grounding strap You need the following tools to assemble the cables for a DC power supply unit.
Figure 15. Removing the front bezel 1. bezel key 2. bezel 3. release latch 4. system Next steps Install the optional front bezel. Related concepts Installing the optional front bezel on page 72 Installing the optional front bezel Steps 1. Locate and remove the bezel keys. NOTE: There are two bezel keys attached to the back of the bezel. 2. Insert the bezel tabs into the bezel tab slots in the chassis. 3. Press the release latch, and push the bezel toward the system until the bezel locks into place. 4.
Figure 16. Installing the front bezel a. bezel key b. bezel c. system Related concepts Removing the optional front bezel on page 71 System feet The system feet provide stability to the system in the tower mode. Removing the system feet Prerequisites NOTE: It is recommended that you remove the system feet only when you are converting the system from the tower mode to the rack mode, or when you are replacing the system feet with the wheel assembly. 1. 2. 3. 4.
Figure 17. Removing and installing the system feet 1. tab slot (12) 3. tab (12) 5. system feet (4) 2. screw hole (4) 4. base of the tower 6. screw (4) Related concepts Installing the system feet on page 74 Related references Safety instructions for converting system from tower to rack on page 69 Installing the system feet Prerequisites CAUTION: Installing the feet on a stand-alone tower system is necessary to provide a stable foundation for the system.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Removing the system feet on page 73 Caster wheels – optional Caster wheels provide mobility to the system in the tower mode. The caster wheel assembly consists of: ● Caster wheel units (front and back) ● Two screws for the caster wheel units Removing caster wheels Prerequisites 1. Follow the safety guidelines listed in the safety instructions section. 2. Keep the Phillips #2 screwdriver ready. 3.
Figure 18. Removing caster wheels 1. slots on base of the tower (4) 3. screw (2) 2. wheel assembly unit (2) 4. screw for support unit (2) 5. support unit Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing caster wheels on page 76 Installing caster wheels Prerequisites 1. 2. 3. 4. Follow the safety guidelines listed in the safety instructions section. Keep the Phillips #2 screwdriver ready.
2. Offset the back wheel slightly to the back of the system and secure the unit in place by using a single screw. 3. Align the two retention hooks on the front wheel with the two slots on the base of the chassis, and insert the hooks into the slots. 4. Offset the front wheel slightly to the front and secure the unit in place by using a screw. Figure 19. Installing caster wheels 1. slots on base of the tower (4) 3. screw (2) 2. wheel assembly unit (2) 4. screw for support unit (2) 5.
System cover The system cover protects the components inside the system and helps in maintaining air flow inside the system. Removing the system cover activates the intrusion switch. Removing the system cover Prerequisites 1. 2. 3. 4. 5. Follow the safety guidelines listed in the Safety instructions section. Turn off the system and any attached peripherals. Disconnect the system from the electrical outlet and peripherals. If installed, remove the front bezel. Place the system on a flat, stable surface.
Related tasks Installing the system cover on page 79 Installing the system cover Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. 3. Ensure that all internal cables are connected and placed out of the way, and no tools or extra parts are left inside the system. Steps 1. Align the slots on the system cover with the tabs on the chassis. 2.
Related tasks Removing the system cover on page 78 Inside the system CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Figure 22. Inside the system 1.
Cooling shroud The cooling shroud aerodynamically directs the airflow across the entire system. The airflow passes through all the critical parts of the system, where the vacuum pulls air across the entire surface area of the heat sink, thus allowing increased cooling. Removing the cooling shroud Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Related tasks Before working inside your system on page 70 Removing the optional cooling fan assembly on page 85 Installing the cooling shroud Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Related tasks Before working inside your system on page 70 Cooling fans There are two cooling fans on the cooling shroud and an optional cooling fan assembly that houses four cooling fans on your system. NOTE: Each fan is listed in the system’s management software, referenced by the respective fan number. If there is a problem with a particular fan, you can easily identify and replace the proper fan by noting the fan numbers on the cooling fan assembly. Removing a cooling fan Prerequisites 1.
Figure 25. Removing a cooling fan from the cooling-fan assembly a. cooling-fan assembly b. fan release tab c. cooling fan Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing a cooling fan on page 84 After working inside your system on page 70 Installing a cooling fan Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 26. Installing a cooling fan into the cooling-fan assembly Next steps 1. cooling-fan assembly 2. fan release tab 3. cooling fan 4. cooling fan connector on the system board Related references Safety instructions for converting system from tower to rack on page 69 Related tasks After working inside your system on page 70 Cooling-fan assembly (optional) The cooling fan assembly is an essential part of a server’s cooling system.
2. Follow the procedure listed in the Before working inside your system section. Steps 1. Unlock the cooling fan assembly from the chassis by lifting the release levers up. 2. Lift the cooling fan assembly out of the chassis. Figure 27. Removing the cooling fan assembly a. cooling fan assembly b. cooling fan (4) c.
2. Slide the cooling fan assembly into the chassis. 3. Lock the cooling fan assembly into the chassis by pressing the release levers down. Next steps Follow the procedure listed in the After working inside your system section. Figure 28. Installing the cooling fan assembly 1. cooling-fan assembly 3. release lever (2) 5. guide pin (6) 2. cooling fan (4) 4.
Figure 29. Memory socket locations Memory channels are organized as follows: Table 28. Memory channels Processor Channel 0 Channel 1 Channel 2 Channel 3 Processor 1 Slots A1, A5, and A9 Slots A2, A6, and A10 Slots A3, A7, and A11 Slots A4, A8, and A12 Processor 2 Slots B1, B5, and B9 Slots B2, B6, and B10 Slots B3, B7, and B11 Slots B4, B8, and B12 The following table shows the memory populations and operating frequencies for the supported configurations: Table 29.
The system supports Flexible Memory Configuration, enabling the system to be configured and run in any valid chipset architectural configuration. The following are the recommended guidelines for installing memory modules: ● ● ● ● ● ● ● ● ● ● ● ● RDIMMs and LRDIMMs must not be mixed. x4 and x8 DRAM based memory modules can be mixed. For more information, see the Mode-specific guidelines section. Up to three dual- or single-rank RDIMMs can be populated per channel.
Memory mirroring Memory mirroring offers the strongest memory module reliability mode compared to all other modes, providing improved uncorrectable multi-bit failure protection. In a mirrored configuration, the total available system memory is one half of the total installed physical memory. Half of the installed memory is used to mirror the active memory modules. In the event of an uncorrectable error, the system switches over to the mirrored copy. This ensures SDDC and multi-bit protection.
Table 31.
Table 32.
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. 1. 2. 3. 4. Follow the safety guidelines listed in the Safety instructions section. Follow the procedure listed in the Before working inside your system section. Remove the cooling shroud. If installed, remove the cooling fan assembly.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Removing the optional cooling fan assembly on page 85 Installing memory modules on page 94 Installing memory modules Prerequisites NOTE: The memory modules are hot to touch for some time after the system has been powered down. Allow the memory modules to cool before handling them.
Figure 31. Installing the memory module a. memory module b. alignment key c. memory module socket ejector (2) Next steps 1. Follow the procedure listed in the After working inside your system section. 2. Press F2 to enter System Setup, and check the System Memory setting. The system should have already changed the value to reflect the installed memory. 3. If the value is incorrect, one or more of the memory modules may not be installed properly.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1. Remove the cables. a. For a 2.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1. Align the tabs on the flex bay with the slots on the front of the chassis. 2.
NOTE: Do not mix enterprise-class hard drives with entry hard drives. Choosing the right drive type depends on the usage pattern. Improper use of entry hard drives (workload rating exceeds 55TB/ year) will lead to significant risk and increase the drives failure rate. For more information on these hard drives, see the 512e and 4Kn Disk Formats whitepaper and 4K Sector HDD FAQ document at Dell.com/poweredgemanuals. All hard drives are connected to the system board through the hard drive backplane.
Figure 34. Removing a hot swappable hard drive or SSD a. release button b. hard drive or SSD carrier c. hard drive or SSD carrier handle Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 After working inside your system on page 70 Removing the optional front bezel on page 71 Installing a hot swappable hard drive Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Steps 1. If a hard drive blank is installed in the hard drive slot, remove it. 2. Install a hard drive in the hard drive carrier. For more information, see the Installing a hot swappable hard drive into a hot swappable hard drive carrier section. 3. Press the release button on the front of the hard drive carrier and open the hard drive carrier handle. 4. Insert the hard drive carrier into the hard drive slot until the carrier connects with the backplane. 5.
Figure 36. Removing a 2.5-inch hard drive blank a. hard drive blank b. release button Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing a 2.5-inch hard drive blank on page 101 Installing a 2.5-inch hard drive blank Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. If installed, remove the front bezel.
Related tasks Removing a 2.5-inch hard drive blank on page 100 Removing a 3.5-inch hard drive blank Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Steps Insert the hard drive blank into the hard drive slot until the release button clicks into place. Figure 39. Installing a 3.5-inch hard drive blank a. hard drive blank Next steps If applicable, install the front bezel. Related references Safety instructions for converting system from tower to rack on page 69 Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 40. Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter a. 3.5-inch hard drive adapter b. screw (2) c. 2.5-inch hard drive Next steps Install the 3.5-inch adapter into the 3.5-inch hard drive carrier. Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter on page 104 Removing a 2.5-inch hard drive from a 3.
Figure 41. Removing a 2.5-inch hard drive from a 3.5-inch hard drive adapter a. 3.5-inch hard drive adapter b. screw (2) c. 2.5-inch hard drive Next steps Install a 2.5-inch hard drive into a 3.5-inch hard drive adapter. Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing a 2.5-inch hard drive into a 3.5-inch hard drive adapter on page 103 Installing a 3.
Figure 42. Installing a 3.5-inch hard drive adapter into a hot swappable hard drive carrier 1. 3.5-inch hard drive carrier 3. hard drive adapter 2. screw (5) 4. 2.5-inch hard drive Next steps 1. Install the hot swappable hard drive carrier into the system. 2. If removed, install the front bezel. Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Removing a 3.5-inch hot swappable hard drive adapter from a 3.
Figure 43. Removing a 3.5-inch hot swappable hard drive adapter from a 3.5-inch hot swappable hard drive carrier 1. 3.5-inch hard drive carrier 3. hard drive adapter 2. screw (5) 4. 2.5-inch hard drive Next steps If removed, install the front bezel. Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing a 3.
Next steps If applicable, install a hard drive into the hard drive carrier. Related references Safety instructions for converting system from tower to rack on page 69 Installing a hot swappable hard drive into a hot swappable hard drive carrier Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Table 33. System configurations System Configurations Systems with up to eight 3.5 inch hard drives or sixteen 2.5 inch hard drives Up to three SATA half height optical drives Up to three SATA/SAS/SCSI tape drives A combination of optical and tape drives Systems with up to eight 3.5 inch hard drives or eight 2.5 inch Up to one SATA half height optical drive hard drives in the 3.5 inch hard-drive carrier, or sixteen 2.
Figure 46. Removing the optical drive or tape drive a. optical drive/tape drive b. guide c. release latch NOTE: The following figure shows the cabling diagram for an optical drive/tape drive with an x16 backplane. All backplanes (x8, x18, and x16) have an ODD connector.
Figure 47. Cabling— optical drive and tape drive 1. ODD1/TBU connector on system board 3. mini-SAS/SATA connector on internal tape adapter 2. ODD2/TBU connector on system board 4. internal tape adapter 5. system board 6. SAS tape drive 7. optical drive 2 8. optical drive 1 Next steps Follow the procedure listed in the After working inside your system section.
Installing the optical drive or tape drive Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. 1.
Next steps Follow the procedure listed in the After working inside your system section. Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing an expansion card on page 120 After working inside your system on page 70 Removing the slim optical drive blank Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Installing the slim optical drive blank Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. 1.
NOTE: To locate the internal USB port (INT_USB) on the system board, see the System board jumpers and connectors section. Replacing the optional internal USB memory key Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. Steps 1. Locate the USB port or USB memory key on the system board. To locate the USB port, see the System board jumpers and connectors section. 2.
Related tasks Before working inside your system on page 70 After working inside your system on page 70 Expansion card holder Removing the expansion card holder Prerequisites 1. Follow the safety guidelines listed in the safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. CAUTION: Many repairs may only be done by a certified service technician.
Installing the expansion card holder Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
Expansion cards An expansion card in the system is an add-on card that can be inserted into an expansion slot on the system board or riser card to add enhanced functionality to the system through the expansion bus. Expansion card installation guidelines The following table describes the supported expansion cards: Table 34.
Table 35.
2. Press the expansion card latch and push down the latch to open it. 3. Hold the expansion card by its edge, and pull the card up to remove it from the expansion card connector and the system. 4. Install the filler brackets by performing the following steps: a. Align the slot on the filler bracket with the tab on the expansion card slot. b. Press the expansion card latch till the filler bracket locks into place.
Steps 1. Unpack the expansion card and prepare it for installation. For instructions, see the documentation accompanying the card. 2. Open the expansion card latch adjacent to the slot you want to install the expansion card. 3. Remove the existing expansion card or filler bracket from the expansion card holder. NOTE: Store this bracket for future use. Filler brackets must be installed in empty expansion-card slots to maintain FCC certification of the system.
GPU card holder (optional) Removing the optional GPU card holder Prerequisites 1. Follow the safety guidelines listed in the safety instructions section. 2. Follow the procedure listed in the Before working inside your system section 3. Remove the cooling shroud. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Installing the optional GPU card holder Prerequisites 1. Follow the safety guidelines listed in the safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
GPU cards (optional) GPU card installation guidelines Observe the following guidelines while installing a GPU card: ● ● ● ● ● ● ● ● ● ● ● ● Ensure that the GPU enablement kit is ready. Ensure that all GPU cards are of the same type or model. Each GPU card supports up to 6 GB of dedicated GDDR5 memory. A single processor configuration only supports up to two double or single width cards on slots 1 and 3.
Figure 59. Removing a GPU card 1. expansion card latch (2) 3. SLI data connector 5. GPU card power connector 2. GPU card 4. GPU card power connector 6. x16 connector Next steps 1. Perform the following steps to install the filler brackets: 2. 3. 4. 5. a. Align the slot on the filler bracket with the tab on the expansion card slot. b. Press the expansion card latch till the filler bracket locks into place.
1. 2. 3. 4. 5. 6. Follow the safety guidelines listed in the Safety instructions section. Follow the procedure listed in the Before working inside your system section. Remove the cooling shroud. Remove the expansion card holder. Open the two expansion card latches. Remove the filler brackets. NOTE: Store this bracket for future use. Filler brackets must be installed in empty expansion-card slots to maintain FCC certification of the system.
Removing an optional GPU card on page 124 Removing the expansion card holder on page 116 Internal dual SD module (optional) The Internal Dual SD Module (IDSDM) card provides two SD card slots. This card offers the following features: ● Dual card operation — maintains a mirrored configuration by using SD cards in both the slots and provides redundancy.
Table 36. IDSDM indicator codes Convention IDSDM indicator code Description A Green Indicates that the card is online. B Flashing green Indicates rebuild or activity. C Flashing amber Indicates card mismatch or that the card has failed. D Amber Indicates that the card is offline, has failed, or is write protected. E Not lit Indicates that the card is missing or is booting. Next steps 1. Install the IDSDM. 2. If removed, install the SD cards. 3.
Related tasks Before working inside your system on page 70 Internal SD card Removing an internal SD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. CAUTION: Many repairs may only be done by a certified service technician.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing the optional internal dual SD module on page 128 Before working inside your system on page 70 After working inside your system on page 70 Installing an internal SD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. 3. If installed, remove the cooling shroud.
Figure 63. Installing an internal SD card 1. IDSDM 3. SD card 1 5. SD card slot 2 2. SD card 2 4. SD card slot 1 Next steps Follow the procedure listed in the After working inside your system section. Processors and heat sinks Use the following procedures when: ● Removing and installing a heat sink ● Installing an additional processor ● Replacing a processor NOTE: To ensure proper cooling, you must install a processor blank in any empty processor socket.
5. Remove the cooling shroud. 6. Keep the Phillips #2 screwdriver ready. Steps 1. Loosen one of the screws that secure the heat sink to the system board. Allow some time (approximately 30 seconds) for the heat sink to loosen from the processor. 2. Remove the screw diagonally opposite to the screw that you first removed. 3. Repeat step 1 and 2 for removing the remaining two screws. 4. Remove the heat sink. Figure 64. Removing a heat sink 1. heat sink 3. retention screw slots (4) 2. retention screws (4) 4.
NOTE: This is a Field Replaceable Unit (FRU). Removal and installation procedures should be performed only by Dell certified service technicians. NOTE: If you are upgrading your system, download the latest system BIOS version from Dell.com/support and follow the instructions included in the compressed download file to install the update on your system. NOTE: You can update the system BIOS by using the Dell Lifecycle Controller.
Figure 65. Processor shield 1. close first socket release lever 3. processor 5. unlock icon 134 Installing and removing system components 2. lock icon 4.
Figure 66. Removing a processor 1. 3. 5. 7. close first socket-release lever processor processor shield socket 2. 4. 6. 8. pin-1 indicator of processor slot (4) open first socket-release lever socket keys (4) Next steps 1. 2. 3. 4. Replace the processor(s). Install the heat sink. Reinstall the cooling shroud. Follow the procedure listed in the After working inside your system section.
1. 2. 3. 4. Follow the safety guidelines listed in the Safety instructions section. Follow the procedure listed in the Before working inside your system section. Keep the Phillips #2 screwdriver ready. If you are upgrading your system, download the latest system BIOS version from Dell.com/support and follow the instructions included in the compressed download file to install the update on your system. NOTE: You can also update the system BIOS by using the Dell Lifecycle Controller. 5.
Figure 67. Installing a processor 1. 3. 5. 7. socket-release lever 1 processor processor shield processor socket 2. 4. 6. 8. pin–1 corner of the processor slot (4) socket-release lever 2 tab (4) Next steps NOTE: Ensure that you install the heat sink after you install the processor. The heat sink is necessary to maintain proper thermal conditions. 1. 2. 3. 4. 5. Install the heat sink. If removed, reinstall the PCIe expansion card riser. If disconnected, reconnect the cables to the expansion card(s).
Installing a heat sink Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. 1. 2. 3. 4. 5. 6.
Figure 69. Installing the heat sink 1. heat sink 2. retention screw (4) 3. retention screw slot (4) 4. processor socket Next steps 1. 2. 3. 4. If applicable, install the PCIe card. If applicable, install the cooling fan assembly. Follow the procedure listed in the After working inside your system section. While booting, press F2 to enter System Setup and verify that the processor information matches the new system configuration. 5.
NOTE: When two identical PSUs are installed, power supply redundancy (1+1 – with redundancy or 2+0 – without redundancy) is configured in system BIOS. In redundant mode, power is supplied to the system equally from both PSUs when Hot Spare is disabled. When Hot Spare is enabled, one of the PSUs will be put into standby when system utilization is low to maximize efficiency. NOTE: For AC power supplies, use only power supplies with the Extended Power Performance (EPP) label on the back.
Figure 70. Removing an AC PSU 1. release latch 3. PSU 5. PSU handle 2. PSU cable connector 4. power connector Next steps ● If applicable, install the AC PSU. ● If applicable, install the PSU blank. Related tasks Installing an AC power supply unit on page 141 Installing an AC power supply unit Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
discovered and enabled before you remove the other PSU. The PSU status indicator turns green to signify that the PSU is functioning properly. Figure 71. Installing an AC PSU 1. release latch 3. PSU 5. PSU handle 2. PSU cable connector 4. power connector Related tasks Removing an AC power supply unit on page 140 Wiring instructions for a DC power supply unit Your system supports up to two –(48–60) V DC power supply units (when available).
● #6-32 nut equipped with lock washer (1) Required tools Wire-stripper pliers, capable of removing insulation from size 10 AWG solid or stranded, insulated copper wire. NOTE: Use alpha wire part number 3080 or equivalent (65/30 stranding).
Related references Safety instructions for converting system from tower to rack on page 69 Assembling the DC input power wires Prerequisites NOTE: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices.
Removing a DC power supply unit Prerequisites NOTE: For equipment using –(48–60) V DC power supply units (PSUs), a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
wiring must comply with applicable local or national codes and practices. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow all safety instructions that came with the product. 1. 2. 3. 4. Follow the safety guidelines listed in the Safety instructions section. Follow the procedure listed in the Before working inside your system section. If installed, remove the PSU blank.
Removing a DC power supply unit on page 145 Removing the power supply unit blank Install the power supply unit (PSU) blank only in the second PSU bay. Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Installing the power supply unit blank Install the power supply unit (PSU) blank only in the second PSU bay. Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. 1. Follow the safety guidelines listed in the Safety instructions section. 2.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks After working inside your system on page 70 Before working inside your system on page 70 Removing the cooling shroud on page 81 Hard drive backplane Depending on the configuration, your system supports one of the following: ● ● ● ● ● 3.5 3.5 2.5 2.5 2.
Figure 80. Removing the PCIe SSD hard drive backplane 1. 3. 5. 7. 9. release tab hard-drive connector power cable power connector on backplane PCIe cable connector on backplane 2. 4. 6. 8. PCIe SSD hard drive backplane PCIe cable signal cable signal cable connector on backplane Figure 81. Removing a 3.5 inch (x8) SAS/SATA backplane 1. SAS cable 3. backplane power connector 5. release pin 2. x8 backplane 4. backplane power cable 6.
Figure 82. Cabling—3.5 inch (x8) SAS/SATA backplane 1. SAS A connector on system board 2. SAS B connector on system board 3. system board 4. signal connector on system board 5. x8 backplane 6. signal connector on backplane 7. SAS B connector on backplane 8.
Figure 83. Removing a 3.5 inch (x8) SAS/SATA backplane with a single PERC card 1. SAS cable 3. power connector 5. release pin 2. x8 backplane 4. power cable 6.
Figure 84. Cabling—3.5 inch (x8) SAS/SATA backplane with a single PERC card 1. 3. 5. 7. 9. 154 SAS B connector on PERC card PERC card signal connector on system board signal connector on backplane SAS A connector on backplane Installing and removing system components 2. 4. 6. 8.
Figure 85. Removing a 3.5 inch (x8) plus 2.5 Inch (x4) SAS/SATA backplane 1. x8 backplane power cable 3. x8 backplane 2. power connector on x8 backplane 4. release pin 5. SAS cable on x8 backplane 6. signal cable on x8 backplane 7. power cable on PCIe SSD backplane 8. PCIe cable on PCIe SSD backplane 9. signal cable on PCIe SSD backplane 10. power connector on PCIe SSD backplane 11. signal connector on PCIe SSD backplane 12. PCIe SSD backplane 13.
Figure 86. Cabling—3.5 Inch (x8) plus 2.5 inch (x4) SAS/SATA backplane 1. PCIe C connector on PCIe SSD backplane 2. PCIe B connector on PCIe SSD backplane 3. PCIe A connector on PCIe SSD backplane 4. PCIe SSD backplane signal connector 5. SAS B cable from 3.5 inch backplane on PERC card 6. SAS A cable from 3.5 inch backplane on PERC card 7. PCIe C connector from PCIe SSD backplane to PCIe extender card 8. PCIe A connector from PCIe SSD backplane to PCIe extender card 9.
21. PCIe SSD backplane Figure 87. Removing a 3.5 inch (x18) SAS/SATA backplane 1. x18 backplane 3. release pin 5. power connector 2. signal cable 4. power cable 6.
Figure 88. Cabling—3.5 inch (x18) SAS/SATA backplane 1. SAS B connector on PERC card 3. PERC card 5. signal connector on system board 2. SAS A connector on PERC card 4. System board 6. SAS A connector on backplane 7. SAS B connector on backplane 9. signal connector on backplane 8.
Figure 89. Removing a 2.5 inch (x16) SAS/SATA backplane 1. x16 backplane 3. signal cable 5. power cable 2. release pin 4. power connector 6.
Figure 90. Cabling—2.5 inch (x16) SAS/SATA backplane 1. 3. 5. 7. 9. 160 SAS B connector on PERC card PERC card signal connector on system board SAS A connector on backplane signal connector on backplane Installing and removing system components 2. 4. 6. 8.
Figure 91. Removing a 2.5 inch (x16) plus 2.5 Inch (x4) SAS/SATA backplane 1. x16 backplane 2. release pin 3. signal cable to x16 backplane 5. power cable to x16 backplane 7. power cable to PCIe SSD backplane 4. power connector on x16 backplane 6. SAS cable to x16 backplane 8. PCIe cable to PCIe SSD backplane 9. signal cable to PCIe SSD backplane 10. power connector on PCIe SSD backplane 11. signal connector on PCIe SSD backplane 12. PCIe SSD backplane 13.
Figure 92. Cabling—2.5 inch (x16) plus 2.5 inch (x4) SAS/SATA backplane 1. PCIe C connector on PCIe SSD backplane 2. PCIe B connector on PCIe SSD backplane 3. PCIe A connector on PCIe SSD backplane 4. PCIe SSD backplane signal connector 5. SAS B cable from 2.5 inch backplane on PERC card 6. SAS A cable from 2.5 inch backplane on PERC card 7. PCIe C connector from PCIe SSD backplane to PCIe extender card 8. PCIe A connector from PCIe SSD backplane to PCIe extender card 9.
21. PCIe SSD backplane Figure 93. Removing a 2.5 inch (x32) SAS/SATA backplane with two PERC cards 1. release pin 2. signal cable to backplane 2 3. power connector on backplane 2 4. power cable to backplane 2 5. SAS cable to backplane 2 6. signal cable to backplane 1 7. power connector on backplane 1 8. power cable to backplane 1 9. SAS cable to backplane 1 10. backplane 1 11.
Figure 94. Cabling—2.5 inch (x32) SAS/SATA backplane with two PERC cards 1. 3. 5. 7. 9. 11. 13. 15. 17. 164 signal connector on backplane 2 SAS A connector on backplane 2 SAS A connector on PERC 1 SAS A connector on PERC 2 PERC card 1 signal cable from backplane 2 on system board SAS B connector on backplane 1 backplane 1 backplane 2 Installing and removing system components 2. 4. 6. 8. 10. 12. 14. 16.
Figure 95. Removing 2.5 inch (x32) SAS/SATA backplane with a single PERC card 1. release pin 2. signal cable to backplane 2 3. power connector on backplane 2 4. power cable to backplane 2 5. SAS cable to backplane 2 6. signal cable to backplane 1 7. power connector on backplane 1 8. power cable to backplane 1 9. SAS cable to backplane 1 10. x16 backplane 1 11. SAS connector on backplane 2 12.
Figure 96. Cabling—2.5 inch (x32) SAS/SATA backplane with a single PERC card 1. signal connector on backplane 2 3. SAS A connector on backplane 2 2. SAS B connector on backplane 2 4. SAS B connector on PERC card 5. SAS A connector on PERC card 6. x32 PERC card 7. system board 8. backplane 2 signal connector on system board 9. backplane 1 signal connector on system board 10. SAS B connector on backplane 1 11. SAS A connector on backplane 1 12. backplane 1 13. signal connector on backplane 1 14.
Removing the optional cooling fan assembly on page 85 Installing the hard drive backplane Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Figure 97. Installing the PCIe SSD hard drive backplane 1. PCIe SSD hard drive backplane 2. PCIe SSD hard drive connector 3. PCIe cable 4. power cable 5. signal cable 6. power connector on backplane 7. signal cable connector on backplane 8. PCIe cable connector on backplane Figure 98. Installing a 3.5 inch (x8) SAS/SATA backplane 1. SAS cable 2. x8 backplane 3. backplane power connector 4. backplane power cable 5. Release pin 6.
Figure 99. Installing a 3.5 inch (x8) SAS/SATA backplane with a single PERC card 1. SAS cable 2. x8 backplane 3. power connector 4. power cable 5. release pin 6. signal cable Figure 100. Installing a 3.5 inch (x8) plus 2.5 Inch (x4) SAS/SATA backplane 1. x8 backplane power cable 3. x8 backplane 2. power connector on x8 backplane 4. release pin 5. SAS cable on x8 backplane 7. power cable on PCIe SSD backplane 6. signal cable on x8 backplane 8.
9. signal cable on PCIe SSD backplane 11. signal connector on PCIe SSD backplane 10. power connector on PCIe SSD backplane 12. PCIe SSD backplane Figure 101. Installing a 3.5 inch (x18) SAS/SATA backplane 1. x18 backplane 2. signal cable 3. release pin 4. power cable 5. power connector 6. SAS cable Figure 102. Installing a 2.5 inch (x16) SAS/SATA backplane 1. x16 backplane 170 Installing and removing system components 2.
3. signal cable 5. power cable 4. power connector 6. SAS cable Figure 103. Installing a 2.5 inch (x16) plus 2.5 Inch (x4) SAS/SATA backplane 1. x16 backplane 2. release pin 3. signal cable to x16 backplane 5. power cable to x16 backplane 7. power cable to PCIe SSD backplane 4. power connector on x16 backplane 6. SAS cable to x16 backplane 8. PCIe cable to PCIe SSD backplane 9. signal cable to PCIe SSD backplane 10. power connector on PCIe SSD backplane 11. signal connector on PCIe SSD backplane 12.
Figure 104. Installing a 2.5 inch (x32) SAS/SATA backplane with two PERC cards 1. release pin 2. signal cable to backplane 2 3. power connector on backplane 2 4. power cable to backplane 2 5. SAS cable to backplane 2 6. signal cable to backplane 1 7. power connector on backplane 1 8. power cable to backplane 1 9. SAS cable to backplane 1 10. x16 backplane 1 11.
Figure 105. Installing a 2.5 inch (x32) SAS/SATA backplane with a single PERC card 1. release pin 2. signal cable to backplane 2 3. power connector on backplane 2 4. power cable to backplane 2 5. SAS cable to backplane 2 6. signal cable to backplane 1 7. power connector on backplane 1 8. power cable to backplane 1 9. SAS cable to backplane 1 10. x16 backplane 1 11. SAS connector on backplane 2 12.
Replacing an optional SD vFlash media card Steps 1. Locate the SD vFlash media slot on the system. 2. To remove the SD vFlash media card, push the card inward to release it, and pull the card from the card slot. Figure 106. Removing the SD vFlash media card a. SD vFlash media card b. SD vFlash media card slot 3. To install an SD vFlash media card, with the label side facing up, insert the contact-pin end of the SD vFlash media card into the card slot on the module.
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1. Remove the screw that secures control panel to the chassis. 2.
ii. tab iii. slot Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing the control panel assembly on page 176 Installing the control panel assembly Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Figure 111. Installing the information tag a. information tag b. tab c. slot 3. Connect the control panel cable and the control panel USB cable to the control panel assembly. 4. Align and insert the control panel into the control panel slot in the chassis. 5. Secure the control panel to the chassis by using the screw. 6. Connect the control panel cable and the control panel USB cable to the system board. Next steps 1. If applicable, install the cooling fan assembly. 2.
1. 2. 3. 4. Follow the safety guidelines listed in the safety instructions section. Keep the Phillips #2 screwdriver ready. Follow the procedure listed in the Before working inside your system section. Remove the following: a. b. c. d. e. f. g. h. i.
Figure 112. Removing the system board a. post b. system board c. release pin Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing the system board on page 179 Installing the system board Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Steps 1. Unpack the new system board assembly. CAUTION: Do not lift the system board by holding a memory module, processor, or other components. 2. Holding the post, incline the system board, and lower the system board into the chassis. 3. Push the system board toward the back of the chassis such that the ports on the system board align with the corresponding slots on the chassis. Next steps 1. Install the Trusted Platform Module (TPM). For information on how to install TPM, see installing TPM section.
Figure 113. Installing the system board a. post b. system board c. release pin Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing the Trusted Platform Module on page 182 Entering the system Service Tag by using System Setup If Easy Restore fails to restore the Service Tag, use System Setup to enter the Service Tag. Steps 1. Turn on the system. 2. Press F2 to enter System Setup. 3.
For more information, see the Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals . Restoring the Service Tag by using the Easy Restore feature By using the Easy Restore feature, you can restore your Service Tag, license, UEFI configuration, and the system configuration data after replacing the system board. All data is automatically backed up in a backup flash device.
2. Align the edge connectors on the TPM with the slot on the TPM connector. 3. Insert the TPM into the TPM connector such that the plastic rivet aligns with the slot on the system board. 4. Press the plastic rivet until the rivet snaps into place. Figure 114. Installing the TPM 1. rivet slot on the system board 3. TPM 2. plastic rivet 4. TPM connector Next steps 1. Install the system board. 2. Follow the procedure listed in the After working inside your system section.
Power interposer board and power distribution board Removing the power interposer board Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
Related tasks Before working inside your system on page 70 Removing the system board on page 177 Installing the power interposer board on page 187 Removing the power distribution board Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Before working inside your system on page 70 Installing the power distribution board Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks After working inside your system on page 70 Removing the power distribution board on page 185 Installing the power interposer board Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Related references Safety instructions for converting system from tower to rack on page 69 Related tasks Installing the power interposer board on page 187 After working inside your system on page 70 188 Installing and removing system components
8 Using system diagnostics If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The purpose of running system diagnostics is to test your system hardware without using additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.
System diagnostic controls Menu Description Configuration Displays the configuration and status information of all detected devices. Results Displays the results of all tests that are run. Systemhealth Provides the current overview of the system performance. Event log Displays a time-stamped log of the results of all tests run on the system. This is displayed if at least one event description is recorded.
9 Jumpers and connectors This topic provides specific information about the jumpers. It also provides some basic information about jumpers and switches and describes the connectors on the various boards in the system. Jumpers on the system board help to disable the system and setup passwords. You must know the connectors on the system board to install components and cables correctly.
Table 37.
System board jumper settings Table 38. System board jumper settings Jumper Setting PWRD_EN Description The password reset feature is enabled (pins 2–4). BIOS local access is unlocked at the next AC power cycle. The password reset feature is disabled (pins 4–6). NVRAM_CLR The configuration settings are retained at the next system boot (pins 3–5). The configuration settings are cleared at system boot (pins 1– 3).
10 Troubleshooting your system Safety first — for you and your system CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product.
Troubleshooting the video subsystem Prerequisites NOTE: Ensure that the Local Server Video Enabled option is selected in the iDRAC Graphical User Interface (GUI), under Virtual Console. If this option is not selected, local video is disabled. NOTE: The VGA ports are not hot-pluggable. Steps 1. Check the cable connections (power and display) to the monitor. 2. Check the video interface cabling from the system to the monitor. Results If the tests run successfully, the problem is not related to video hardware.
14. If a USB device causes the same problem, turn off the device, replace the USB cable with a known good cable, and turn on the device. Next steps If all troubleshooting fails, see the Getting help section. Related references Getting help on page 207 Troubleshooting a serial input and output device Prerequisites Steps 1. Turn off the system and any peripheral devices connected to the serial port. 2.
7. Ensure that all the NICs and switches on the network are set to the same data transmission speed and duplex. For more information, see the documentation for each network device. 8. Ensure that all network cables are of the proper type and do not exceed the maximum length. Next steps If the problem persists, see the Getting help section. Related references Getting help on page 207 Troubleshooting a wet system Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
Troubleshooting a damaged system Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1.
4. Enter System Setup. If the date and time displayed in System Setup are not correct, check the System Error Log (SEL) for system battery messages. Next steps If the problem persists, see the Getting help section. Related references Getting help on page 207 Troubleshooting power supply units Prerequisites CAUTION: Many repairs may only be done by a certified service technician.
6. Reseat the PSU. NOTE: After installing a PSU, allow several seconds for the system to recognize the PSU and determine if it is working properly. If the problem persists, see the Getting help section. Troubleshooting cooling problems CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Next steps 1. Follow the procedure listed in the After working inside your system section. 2. If the problem persists, see the Getting help section. Related references Getting help on page 207 Troubleshooting system memory Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Next steps If the problem persists, see the Getting help section. Related references Getting help on page 207 Troubleshooting an internal USB key Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
6. Reconnect the system to its electrical outlet and turn on the system, including any attached peripherals. 7. Enter System Setup, and ensure that the Internal SD Card Port and Internal SD Card Redundancy modes are set to the needed modes. Verify that the correct SD slot is set as Primary SD Card. 8. Check if the micro SD card is functioning properly. 9. If the Internal SD Card Redundancy option is set to Enabled at the time of the SD card failure, the system prompts you to perform a rebuild.
Steps 1. Run the appropriate diagnostic test. See the Using system diagnostics section. Depending on the results of the diagnostics test, proceed as required through the following steps. 2. If your system has a RAID controller and your drives are configured in a RAID array, perform the following steps: a. Restart the system and press F10 during system startup to run the Dell Lifecycle Controller, and then run the Hardware Configuration wizard to check the RAID configuration.
If the problem persists, see the Getting help section. Related references Getting help on page 207 Troubleshooting expansion cards Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Troubleshooting processors Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. NOTE: Processor sockets are not hot-pluggable. Steps 1.
11 Getting help Topics: • • • • Contacting Dell EMC Documentation feedback Accessing system information by using QRL UEFI iSCSI Settings Contacting Dell EMC Dell EMC provides several online and telephone based support and service options. If you do not have an active internet connection, you can find contact information about your purchase invoice, packing slip, bill, or Dell EMC product catalog. Availability varies by country and product, and some services may not be available in your area.
● Your system service tag to quickly access your specific hardware configuration and warranty information ● A direct link to Dell to contact technical assistance and sales teams Steps 1. Go to www.dell.com/qrl and navigate to your specific product or 2. Use your smartphone or tablet to scan the model-specific Quick Resource (QR) code on your system or in the Quick Resource Locator section.
