Dell PowerEdge T630 オーナーズマニュアル 規制モデル: E25S Series 規制タイプ: E25S001 August 2020 Rev.
目次 章 1: Dell PowerEdge T630 サーバー概要 ........................................................................................... 8 PowerEdge T630 サーバーでサポートされている構成................................................................................................. 8 前面パネル........................................................................................................................................................................... 10 2.5 インチハードドライブシャーシ......................................................
iDRAC の IP アドレスを設定するためのオプション............................................................................................ 39 iDRAC へのログイン..........................................................................................................................................................40 オペレーティング システムをインストールするオプション................................................................................... 40 ドライバとファームウェアのダウンロード......................................................................................
モードごとのガイドライン........................................................................................................................................ 90 メモリー構成の例......................................................................................................................................................... 91 メモリモジュールの取り外し....................................................................................................................................94 メモリモジュールの取り付け..................................
プロセッサの取り外し.............................................................................................................................................. 133 プロセッサの取り付け.............................................................................................................................................. 136 ヒートシンクの取り付け...........................................................................................................................................139 電源装置ユニット....................................
ビデオサブシステムのトラブルシューティング.......................................................................................................196 USB デバイスのトラブルシューティング...................................................................................................................196 シリアル入出力デバイスのトラブルシューティング...............................................................................................197 NIC のトラブルシューティング...........................................................................................................
1 Dell PowerEdge T630 サーバー概要 Dell PowerEdge T630 ラック型サーバーは以下をサポートします。 ● Intel Xeon E5-2600 v4 プロセッサ ● DIMM 24 個 ● 3.5 インチハードドライブ 18 台 ● Dell PowerEdge Express Flash デバイス 4 台 ● 2.
図 1.
前面パネル 2.5 インチハードドライブシャーシ 図 2. 前面パネル - 2.5 インチハードドライブシャーシ 1. SD vFlash カードスロット 2. 電源ボタン 3. NMI ボタン 4. システム識別ボタン 5. LCD メニューボタン 6. 情報タグ 7. LCD パネル 8. iDRAC ダイレクトポート 9. VGA コネクタ 10. USB コネクタ 11. 光学ドライブまたはテープドライブベイ 12.
表 1.
表 1. 前面パネルボタンとコネクタの説明 (続き) 項目 ボタン、またはコネクタ アイコン 10 USB コネクタ これは、USB デバイスをシステムに接続するときに使用します。 ポートは USB 3.0 対応です。 11 光学ドライブまたはテープドラ イブベイ これは、光学ドライブまたはテープドライブを取り付ける際に 使用します。サポートされる光学ドライブとテープドライブに ついては、「光学ドライブとテープドライブ」の項を参照してく ださい。 12 物理ドライブ 最大 32 台の 2.5 インチハードドライブ 説明 関連概念 タワーモードからラックモードにシステムを変換するための準備 、p. 24 3.
図 3. 前面パネル — 3.5 インチハードドライブ + PCIe SSD シャーシ 4 台 1. SD vFlash カードスロット 2. 電源ボタン 3. NMI ボタン 4. システム識別ボタン 5. LCD メニューボタン 6. 情報タグ 7. LCD パネル 8. iDRAC ダイレクトポート 9. VGA コネクタ 10. USB コネクタ 11. 光学ドライブまたはテープドライブベイ 12. フレックスベイ 13. PCIe SSD 14. 3.
表 2.
表 2. 前面パネルボタンとコネクタの説明 (続き) アイテム ボタン、またはコネクタ アイコン 10 USB コネクタ これは、USB デバイスをシステムに接続するときに使用します。 ポートは USB 3.0 対応です。 11 光学ドライブまたはテープドラ イブベイ これは、光学ドライブまたはテープドライブを取り付ける際に 使用します。サポートされる光学ドライブとテープドライブに ついては、「光学ドライブとテープドライブ」の項を参照してく ださい。 12 フレックスベイ 最大 4 台の PCIe SSD のインストールをサポート 13 PCIe SSD 最大 4 台の PCIe SSD 14 物理ドライブ 3.5 インチハードドライブが最大 8 台 説明 関連概念 タワーモードからラックモードにシステムを変換するための準備 、p.
表 3. LCD パネルの機能 (続き) アイテム ボタン 説明 メモ: ボタンを放すと、画面のスクロールが停止します。無活動の状態が 45 秒続くと、画面はスクロールを開始します。 ホーム画面の表示 [ホーム]画面には、システムに関するユーザー設定可能な情報が表示されます。この画面は、通常のシステムの操作中、ステータ ス メッセージやエラーがない場合に表示されます。システムがオフになり、エラーがない場合は、5 分間操作が行われないと LCD がスタンバイ モードになります。LCD をオンにするには、LCD の任意のボタンを押します。 手順 1. Home(ホーム)画面を表示するには、3 つのナビゲーションボタン(Select(選択)、Left(左)、または Right(右))のいずれ かを選択します。 2. 別のメニューから Home(ホーム)画面に移動するには、次の手順を実行します。 a. 上矢印 が表示されるまで、ナビゲーション ボタンを押したままにします。 b. 上矢印 を使用して に移動します。 c. Home(ホーム)アイコンを選択します。 d.
オプション 説明 MAC iDRAC、iSCSI、または Network(ネットワーク)デバイスの MAC アドレスを表示します。 名前 システムの Host(ホスト)、Model(モデル)、または User String(ユーザー文字列)の名前を表示します。 番号 システムの Asset tag(アセットタグ)または Service Tag(サービスタグ)を表示します。 電源 システムの電源出力を BTU/時 またはワットで表示します。表示フォーマットは、Setup(セットアップ) メニューの Set Home(ホームの設定)サブメニューで設定できます。 温度 システムの温度を摂氏または華氏で表示します。Setup(セットアップ)メニューの Set Home(ホームの設 定)サブメニューで設定できます。 背面パネル 図 5. 背面パネルの機能 1. PCIe 拡張カードスロット(3)(プロセッサ 1) 2. イーサネットコネクタ 3. システム識別コネクタ 4. システム識別ボタン 5. iDRAC Enterprise ポート 6. 電源装置(PSU1) 7.
表 4.
表 5. 診断インジケータ アイコン 説明 状態 対応処置 ヘルスインジケー システムが良好な状態である場合 不要。 タ は、インジケータが青色に点灯しま す。 次の場合はインジケータが橙色に点 特定の問題については、「システムイベント ログ」また 滅します。 は「システムメッセージ」を参照してください。エラー メッセージの詳細については、Dell.
図 6. NIC インジケーター コード 1. リンクインジケータ 2. アクティビティインジケータ 表 6.
図 7. AC PSU ステータスインジケータ 1. AC PSU ステータスインジケータ / ハンドル 表 7.
図 8. DC PSU ステータスインジケータ 1. DC PSU ステータスインジケータ 表 8.
図 9. ハードドライブインジケータ 1. ハードドライブアクティビティインジケータ 2. ハードドライブステータスインジケータ 3. ハードドライブ メモ: ハードドライブが Advanced Host Controller Interface(AHCI)モードの場合、ステータスインジケータ(右側)は点灯しま せん。 表 9.
2 タワーモードからラックモードへのシステムの変 換 お使いのシステムをタワーモードからラックモードに変換できます。 お使いのシステムをタワーモードからラックモードに変換するには、次のアイテムを含むタワー / ラック変換キットが必要です。 ● ● ● ● ● ラックタブ(左右)とネジが 3 本ずつ VGA モジュール ラックのスライドカバー 透明シートカバー レール 1 組(オプション) トピック: タワーモードからラックモードにシステムを変換するための準備 • タワーモードからラックモードにシステムを変換するため の準備 前提条件 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 #2 プラスドライバを準備しておきます。 システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 システムを安定した平面に置きます。 システムスタビライザまたはキャスターが取り付けられている場合は、それらを取り外します。詳細については、「システムス タビライザの取り外し」または「キャスターの取り外し」を参照してください。 6.
図 10. ラックスライドカバーの取り付け a. ラックのスライドカバー b. システムシャーシ 図 11. ラックスライドカバーの取り外し a. ラックのスライドカバー b. システムシャーシ 4. コントロールパネルアセンブリを取り付けます。詳細については、「コントロールパネルアセンブリの取り付け」を参照してくだ さい。 5.
図 12. 透明シートカバーの貼り付け a. シャーシ上のマーキング b. 透明シートカバー 6. システムカバーを取り付けます。 7. ラックイヤーの取り付けは、次の手順を実行します。 a. ラックイヤーの 3 つのネジ穴を、システムの上部と下部のネジ穴の位置に合わせます。 b.
図 13. ラックイヤーの取り外し a. ネジ(6) b. ラックイヤー(2) c. ラックモードのシステム 8. システムをラックに取り付けます。詳細については、お使いのシステムに同梱の『Rack Installation Guide』(ラック取り付けガイ ド)を参照してください。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システムカバーの取り外し 、p. 79 コントロールパネルアセンブリの取り外し 、p.
3 マニュアルリソース 本項では、お使いのシステムのマニュアルリソースに関する情報を提供します。 マニュアル リソースの表に記載されているマニュアルを参照するには、次の手順を実行します。 ● Dell EMC サポート サイトにアクセスします。 1. 表の「場所」列に記載されているマニュアルのリンクをクリックします。 2. 目的の製品または製品バージョンをクリックします。 メモ: 製品名とモデルを確認する場合は、お使いのシステムの前面を調べてください。 3. [製品サポート]ページで、マニュアルおよび文書をクリックします。 ● 検索エンジンを使用します。 ○ 検索 ボックスに名前および文書のバージョンを入力します。 表 10. お使いのシステムのためのその他マニュアルのリソース タスク 文書 場所 システムのセットア ップ システムをラックに取り付けて固 www.dell.
表 10. お使いのシステムのためのその他マニュアルのリソース (続き) タスク 文書 場所 お使いのシステムで使用可能な iDRAC のバージョンを特定するに は、iDRAC Web インターフェイス で?、About の順にクリックします。 オペレーティング システムのイン ストールについての情報は、オペ レーティング システムのマニュア ルを参照してください。 www.dell.com/ operatingsystemmanuals ドライバおよびファームウェアの www.dell.com/support/drivers アップデートについての情報は、本 書の「ファームウェアとドライバを ダウンロードする方法」の項を参照 してください。 システムの管理 デルが提供するシステム管理ソフ トウェアについての情報は、『Dell OpenManage Systems Management 概要ガイド』を参照してください。 www.dell.com/poweredgemanuals OpenManage のセットアップ、使 www.dell.
表 10. お使いのシステムのためのその他マニュアルのリソース (続き) タスク 文書 場所 成されたイベント メッセージおよ びエラー メッセージの情報につい ては、「Error Code Lookup」を参照し てください。 システムのトラブル シューティング 30 PowerEdge サーバーの問題を特定し www.dell.
4 技術仕様 本項では、お使いのシステムの技術仕様と環境仕様の概要を示します。 トピック: • • • • • • • • • • • シャーシ寸法 シャーシ重量 プロセッサの仕様 PSU の仕様 システムバッテリの仕様 拡張バスの仕様 メモリの仕様 ドライブの仕様 ポートおよびコネクタの仕様 ビデオの仕様 環境仕様 技術仕様 31
シャーシ寸法 図 14. Dell PowerEdge T630 システム寸法詳細 表 11. Dell PowerEdge T630 システムの寸法 システム Xa PowerEdge 304.5 T630 Xb Ya Yb Yc Za(ベゼル Za(ベゼル Zb* 付き) 無し) Zc 217.9 434.5 443.5 471.5 15.9 692.8 シャーシ重量 表 12. シャーシ重量 PowerEdge T630 最大重量 3.5 インチハードドライブシャーシ 49.65 kg 32 技術仕様 0.0 659.
表 12. シャーシ重量 (続き) PowerEdge T630 最大重量 2.5 インチハードドライブシャーシ 42.36 kg プロセッサの仕様 PowerEdge T630 システムは、最大 2 個の Intel Xeon E5-2600 v4 または Xeon E5-2600 v3 製品シリーズプロセッサをサポートしま す。 PSU の仕様 PowerEdge T630 システムは、最大 2 台の AC または DC 冗長電源装置ユニット(PSU)をサポートします。 表 13.
表 14. サポートする PCI Express Generation 3 拡張カード (続き) PCIe スロット プロセッサの接続 高さ 長さ リンク幅 スロット幅 6(第 3 世代) プロセッサ 2 標準ハイト フルレングス x16 x16 7(第 3 世代) プロセッサ 2 標準ハイト フルレングス x16 x16 8(内蔵 PERC ス ロット) プロセッサ 1 標準ハイト ハーフレングス x8 x8 *PCIe 第 2 世代拡張カード。 メモ: PCIe スロット 4、5、6、7 を使用するには、両方のプロセッサを取り付ける必要があります。 メモ: 拡張カードスロットはホットスワップ対応ではありません。 メモリの仕様 PowerEdge T630 システムは、高度な ECC またはメモリ最適化動作のために、1,866 MT/s、2,133 MT/s、または 2,400 MT/s DDR4 レジスタードまたは負荷軽減エラー修正コード(ECC)DIMM をサポートしています。 表 15.
光学ドライブ PowerEdge T630 システムは、1 台のオプションの SATA DVD-ROM ドライブ、DVD+/-RW ドライブ、または 1 台のスリム SATA DVD-ROM ドライブ、DVD +/-RW ドライブをサポートします。 メモ: DVD デバイスはデータ専用です。 ポートおよびコネクタの仕様 シリアルコネクタ シリアルコネクタは、シリアルデバイスをシステムに接続します。PowerEdge T630 システムは DB-9 シリアルポートコネクタに対 応しています。 内蔵デュアル SD モジュール PowerEdge RT630 システムは、内蔵 SD モジュールを備えたオプションのフラッシュメモリカードスロットを 2 個サポートします。 メモ: カードスロット 1 個は冗長専用。 VGA ポート ビデオグラフィックアレイ(VGA)ポートでは、システムを VGA ディスプレイに接続することができます。PowerEdge T630 シス テムは、前面および背面パネルで 15 ピン VGA ポートを 2 つサポートしています。 メモ: 前面 VGA ポートは、ラック構成でのみ使用でき
ビデオの仕様 PowerEdge T630 システムは、iDRAC8 および 16 MB アプリケーションメモリ搭載の Integrated Matrox G200 をサポートしています。 表 17. サポートされているビデオ解像度のオプション 解像度 リフレッシュレート(Hz) 色深度(ビット) 640 x 480 60、70 8、16、32 800 x 600 60、75、85 8、16、32 1024 x 768 60、75、85 8、16、32 1280 x 1024 60 8、16、32 1440 x 900(ストレッチ目標) 60 8、16、32 環境仕様 メモ: 特定のシステム構成でのその他の環境条件の詳細については、Dell.com/environmental_datasheets を参照してくださ い。 表 18.
表 22. 最大高度の仕様 最大高度 仕様 動作時 30482000 m(10,0006560 フィート) 保管時 12,000 m(39,370 フィート) 表 23.
動作時の拡張温度 表 26. 動作時の拡張温度の仕様 動作時の拡張温度 仕様 継続動作 相対湿度 5~85%、露点温度 29°C(84.
5 システムの初期セットアップと設定 トピック: • • • • • システムのセットアップ iDRAC 設定 iDRAC へのログイン オペレーティング システムをインストールするオプション ドライバとファームウェアのダウンロード システムのセットアップ 次の手順を実行して、システムを設定します。 手順 1. システムを開梱します。 2. システムをラックに取り付けます。ラックへのシステムの取り付けの詳細については、システムの「ラック取り付けプレースマ ット」(Dell.com/poweredgemanuals)を参照してください。 3. 周辺機器をシステムに接続します。 4. システムを電源コンセントに接続します。 5. 電源ボタンを押す、または iDRAC を使用してシステムの電源を入れます。 6.
メモ: iDRAC にアクセスするには、iDRAC ポートカードを取り付ける、またはネットワークケーブルをシステム基板上の Ethernet コネクタ 1 に接続するようにします。 メモ: iDRAC IP アドレスをセットアップした後は、デフォルトのユーザー名とパスワードを変更してください。 iDRAC へのログイン iDRAC には、次の資格でログインできます。 ● iDRAC ユーザー ● Microsoft Active Directory ユーザー ● Lightweight Directory Access Protocol(LDAP)ユーザー デフォルトのユーザー名とパスワードは、root と calvin です。シングル サイン オンまたはスマート カードを使用してログイン することもできます。 メモ: iDRAC にログインするには、iDRAC 資格情報が必要です。 iDRAC へのログイン、および iDRAC ライセンスの詳細については、Dell.
ユーザーの選択した項目に該当するドライバが表示されます。 4.
6 プレオペレーティング システム管理アプリケー ション システムのファームウェアを使用して、オペレーティング システムを起動せずにシステムの基本的な設定や機能を管理することが できます。 トピック: • • • • • • プレオペレーティングシステムアプリケーションを管理するためのオプション セットアップユーティリティ デバイス設定 Dell Lifecycle Controller ブートマネージャ PXE 起動 プレオペレーティングシステムアプリケーションを管理す るためのオプション お使いのシステムには、プレオペレーティングシステムアプリケーションを管理するための次のオプションがあります。 ● ● ● ● セットアップユーティリティ ブートマネージャ Dell Lifecycle Controller Preboot Execution Environment(PXE) 関連概念 セットアップユーティリティ 、p. 42 ブートマネージャ 、p. 69 Dell Lifecycle Controller 、p. 68 PXE 起動 、p.
セットアップユーティリティの表示 System Setup(セットアップユーティリティ)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 関連概念 セットアップユーティリティ 、p. 42 関連参照文献 セットアップユーティリティ詳細 、p.
内蔵デバイス 、p. 60 シリアル通信 、p. 62 システムプロファイル設定 、p. 64 その他の設定 、p. 66 iDRAC 設定ユーティリティ 、p. 67 デバイス設定 、p. 68 関連タスク システムセキュリティ設定の詳細 、p. 48 システム BIOS の表示 、p. 44 システム BIOS の表示 System BIOS(システム BIOS)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 関連参照文献 システム BIOS 、p. 43 システム BIOS 設定の詳細 、p.
オプション 説明 その他の設定 システムの日時などを変更するオプションを指定します。 関連参照文献 システム BIOS 、p. 43 関連タスク システム BIOS の表示 、p. 44 起動設定 Boot Settings(起動設定) 画面を使用して、起動モードを BIOS または UEFI に設定します。起動順序を指定することも可能で す。 関連参照文献 システム BIOS 、p. 43 システム起動モードの選択 、p. 46 関連タスク 起動設定の詳細 、p. 46 起動設定の表示 、p. 45 起動順序の変更 、p. 47 起動設定の表示 Boot Settings (起動設定)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3.
起動設定の詳細 このタスクについて Boot Settings(起動設定)画面の詳細は、次のとおりです。 オプション 説明 Boot Mode(起動 モード) システムの起動モードを設定できます。 注意: オペレーティングシステムのインストール時の起動モードが異なる場合、起動モードを切り替える と、システムが起動しなくなることがあります。 オペレーティングシステムが UEFI をサポートしている場合は、このオプションを UEFI に設定できます。こ のフィールドを BIOS に設定すると、UEFI 非対応のオペレーティングシステムとの互換性が有効になります。 このオプションはデフォルトでは BIOS に設定されています。 メモ: このフィールドを UEFI に設定すると、BIOS Boot Settings(BIOS 起動設定)メニューが無効に なります。このフィールドを BIOS に設定すると、UEFI Boot Settings(UEFI 起動設定)メニューが無 効になります。 Boot Sequence 起動順序再試行機能を有効または無効にします。このオプションが Enabled(有効)に設定
メモ: ● UEFI 起動モードからインストールする OS は UEFI 対応である必要があります。DOS および 32 ビットの OS は UEFI 非対 応で、BIOS 起動モードからのみインストールできます。 ● 対応オペレーティング システムの最新情報については、 Dell.com/ossupport を参照してください。 関連参照文献 起動設定 、p. 45 関連タスク 起動設定の詳細 、p. 46 起動設定の表示 、p. 45 起動順序の変更 このタスクについて USB キーまたはオプティカルドライブから起動する場合は、起動順序を変更する必要がある場合があります。Boot Mode(起動モ ード)で BIOS を選択した場合は、以下の手順が異なる可能性があります。 手順 1. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > Boot Settings(起動設定) の順にクリックします。 2.
手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で System Security(システムセキュリティ)をクリックします。 関連参照文献 システムセキュリティ 、p. 47 関連タスク システムセキュリティ設定の詳細 、p.
オプション 説明 AC Power Recovery システムの AC 電源が回復した後の、システムの動作を設定します。このオプションは、デフォルトで 前回 に設定されています。 AC Power Recovery Delay システムの AC 電源が回復した後のシステムへの電源投入の時間遅延を設定します。デフォルトでは、この オプションは 即時に設定されています。 User Defined AC 電源リカバリー遅延に ユーザー定義オプションが選択されている場合、ユーザー定義の遅延オプションを Delay(60~240 秒) 設定します。 UEFI Variable Access UEFI 変数を安全に維持するためのさまざまな手段を提供します。標準(デフォルト)に設定されている場 合、UEFI 変数は UEFI 仕様によってオペレーティング システムでアクセス可能です。制御に設定されている 場合、選択した UEFI 変数は環境内で保護され、新しい UEFI 起動エントリは、現在の起動順序の最後に実行 されます。 Secure Boot Policy セキュア ブート ポリシーが標準に設定され
オプション 説明 Key Exchange Key Database キー交換キー(KEK)データベース内のエントリをインポート、エクスポート、削除、または復元できます。 Authorized Signature Database 認証済み署名データベース(db)のエントリをインポート、エクスポート、削除、または復元します。 Forbidden Signature Database 禁止されている署名のデータベース(dbx)のエントリをインポート、エクスポート、削除、または復元しま す。 システム情報 System Information(システム情報)画面を使用して、サービスタグ、システムモデル名、および BIOS バージョンなどのシステ ムプロパティを表示することができます。 関連参照文献 システム情報の詳細 、p. 50 システム BIOS 、p. 43 関連タスク システム情報の表示 、p. 50 システム情報の表示 System Information(システム情報)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2.
オプション 説明 System BIOS システムにインストールされている BIOS バージョンを指定します。 Version(システム BIOS バージョン) System 管理エンジンファームウェアの現在のバージョンを指定します。 Management Engine Version(シ ステム管理エンジ ンバージョン) System Service システムのサービスタグを指定します。 Tag(システムサー ビスタグ) System Manufacturer(シ ステム製造元) システムメーカーの名前を指定します。 System システムメーカーの連絡先情報を指定します。 Manufacturer Contact Information(シス テム製造元の連絡 先情報) System CPLD システムのコンプレックスプログラマブルロジックデバイス(CPLD)ファームウェアの現在のバージョンを Version(システム 指定します。 CPLD バージョン) UEFI Compliance システムファームウェアの UEFI 準拠レベルを指定します。 Version(UEFI 準拠 バージョン) 関
● 特殊文字は、次の文字のみが利用可能です:スペース、(”)、(+)、(,)、(-)、(.)、(/)、(;)、([)、(\)、(])、(`)。 システムパスワードの再入力を求めるメッセージが表示されます。 5. システムパスワードをもう一度入力し、OK をクリックします。 6. Setup Password(セットアップパスワード)フィールドに、セットアップパスワードを入力して、Enter または Tab を押しま す。 セットアップパスワードの再入力を求めるメッセージが表示されます。 7. セットアップパスワードをもう一度入力し、OK をクリックします。 8. Esc を押して System BIOS(システム BIOS)画面に戻ります。もう一度 Esc を押します。 変更の保存を求めるプロンプトが表示されます。 メモ: システムが再起動するまでパスワード保護機能は有効になりません。 関連参照文献 システムセキュリティ 、p. 47 関連タスク システム基板のジャンパ設定 、p. 193 システムセキュリティ設定の詳細 、p.
2. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > System Security(システムセキュリティ) の順にクリックします。 3. System Security(システムセキュリティ)画面で Password Status(パスワードステータス)が Unlocked(ロック解除)に 設定されていることを確認します。 4. System Password(システムパスワード)フィールドで、既存のシステムパスワードを変更または削除して、Enter または Tab を押します。 5. Setup Password(セットアップパスワード)フィールドで、既存のシステムパスワードを変更または削除して、Enter または Tab を押します。 システムパスワードおよびセットアップパスワードを変更する場合は、新しいパスワードの再入力を求めるメッセージが表示さ れます。システムパスワードおよびセットアップパスワードを削除する場合は、削除の確認を求めるメッセージが表示されま す。 6.
手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 Memory Settings(メモリ設定)をクリックします。 関連参照文献 メモリ設定 、p. 53 メモリ設定の詳細 、p.
関連参照文献 メモリ設定 、p. 53 関連タスク メモリ設定の表示 、p. 53 プロセッサ設定 Processor Setting(プロセッサ設定)画面を使用して、プロセッサ設定を表示し、仮想化テクノロジ、ハードウェアプリフェッチ ャ、論理プロセッサアイドリングなどの特定の機能を実行できます。 関連参照文献 プロセッサー設定の詳細 、p. 55 システム BIOS 、p. 43 関連タスク プロセッサ設定の表示 、p. 55 プロセッサ設定の表示 Processor Settings(プロセッサ設定)画面を表示するには、次の手順を実行します。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3.
オプション 説明 代替 RTID(リクエ QPI のリソースであるリクエスタ トランザクション ID を変更します。このオプションは、デフォルトで 無 スタ トランザクシ 効に設定されています。 ョン ID)設定 メモ: このオプションを有効にすると、全体的なシステムパフォーマンスに悪影響を及ぼす場合があり ます。 仮想化テクノロジ ー 仮想化のために提供されている追加のハードウェア機能の有効 / 無効を切り替えます。このオプションは、 デフォルトで有効に設定されています。 Address Translation Service (ATS) デバイスのアドレス変換キャッシュ(ATC)を定義して、DMA トランザクションをキャッシュします。この オプションは、チップセットのアドレス変換と保護テーブルに CPU と DMA メモリー管理の間のインターフ ェイスを提供し、DMA アドレスをホストアドレスに変換します。このオプションは、デフォルトで有効に 設定されています。 隣接キャッシュ ラ インのプリフェッ チ シーケンシャル メモリー アクセスを頻繁に使用する必要があるアプリケーション向けにシステ
オプション 説明 オプション 説明 レベル 3 キャッシ ュ L3 キャッシュの合計を指定します。 コア数 プロセッサーごとのコア数を指定します。 関連参照文献 プロセッサ設定 、p. 55 関連タスク プロセッサ設定の表示 、p. 55 SATA 設定 SATA Settings(SATA 設定)画面を使用して、SATA デバイスの SATA 設定を表示し、お使いのシステムで RAID を有効にするこ とができます。 関連参照文献 システム BIOS 、p. 43 関連タスク SATA 設定の詳細 、p. 58 SATA 設定の表示 、p. 57 SATA 設定の表示 SATA Settings(SATA 設定)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3.
SATA 設定の詳細 このタスクについて SATA Sttings(SATA 設定)画面の詳細は、次の通りです。 オプション Embedded SATA (内蔵 SATA) 説明 Embedded SATA(内蔵 SATA)オプションを Off(オフ)、ATA、AHCI、または RAID のいずれかのモードに 設定できます。デフォルトでは、このオプションは AHCI に設定されています。 Security Freeze POST 中に組み込み SATA ドライブにセキュリティフリーズロックコマンドを送信します。このオプション Lock(セキュリティ は、ATA および AHCI モードにのみ適用されます。 フリーズロック) Write Cache(書き POST 中に組み込み SATA ドライブの コマンドを有効または無効にします。 込みキャッシュ) Port A(ポート A) 選択されたデバイスのドライブタイプを設定します。Embedded SATA settings(組み込み SATA 設定)が ATA モードに設定されている場合、BIOS サポートを有効にするには、このフィールドを Auto(自動
オプション 説明 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブなどのリムーバブル メディアデバイスに対しては未定義です。 Port E(ポート E) 選択されたデバイスのドライブタイプを設定します。Embedded SATA settings(組み込み SATA 設定)が ATA モードに設定されている場合、BIOS サポートを有効にするには、このフィールドを Auto(自動)に設 定する必要があります。BIOS サポートをオフにするには、OFF(オフ)に設定します。 AHCI または RAID モードの場合、BIOS のサポートは常に有効です。 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacit
オプション 説明 オプション 説明 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) Port I(ポート I) ハードドライブの合計容量を指定します。オプティカルドライブなどのリムーバブル メディアデバイスに対しては未定義です。 選択されたデバイスのドライブタイプを設定します。Embedded SATA settings(組み込み SATA 設定)が ATA モードに設定されている場合、BIOS サポートを有効にするには、このフィールドを Auto(自動)に設 定する必要があります。BIOS サポートをオフにするには、OFF(オフ)に設定します。 AHCI または RAID モードの場合、BIOS のサポートは常に有効です。 オプション 説明 Model(モデル) 選択されたデバイスのドライブモデルを指定します。 Drive Type(ドライ SATA ポートに接続されているドライブのタイプを指定します。 ブタイプ) Capacity(容量) ハードドライブの合計容量を指定します。オプティカルドライブな
内蔵デバイスの表示 Integrated Devices(内蔵デバイス)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で、 Integrated Devices(内蔵デバイス)をクリックします。 関連参照文献 内蔵デバイス 、p. 60 関連タスク 内蔵デバイスの詳細 、p. 61 内蔵デバイスの詳細 このタスクについて Integrated Devices(内蔵デバイス)画面の詳細は、次のとおりです。 オプション 説明 USB 3.
オプション 説明 ネットワークドーターカード(NDC)がないシステムでのみ利用できます。このオプションは、内蔵ネット ワークカード 1 オプションと同時に指定することはできません。Embedded NIC1 and NIC2(内蔵 NIC1 および NIC2)オプションは、システムの NIC 管理ユーティリティを使用して設定します。 I/OAT DMA Engine(I/OAT DMA エンジン) I/OAT オプションを有効または無効にします。ハードウェアとソフトウェアがこの機能をサポートしている 場合にのみ、有効にできます。 I/O Snoop Holdoff のサイクル数を PCI I/O 、 CPU から snoop リクエスト、そのを独自の LLC の書き込みが完了する時間を許 Response(I/O ス 可することができます剥奪を選択します。この設定では、スループットを向上させ、レイテンシが重要な作 ヌープレスポンス 業負荷でのパフォーマンスが向上できます。 の先送り) Embedded Video Embedded Video Controller(内蔵ビデオコントローラ)オプションを
シリアル通信の表示 Serial Communication(シリアル通信)画面を表示するには、次の手順を実行してください。 手順 1. システムの電源を入れるか、または再起動します。 2. 次のメッセージが表示されたらすぐに F2 を押します。 F2 = System Setup メモ: F2 を押す前にオペレーティングシステムのロードが開始された場合は、システムの起動が完了するのを待ってから、 システムを再起動してもう一度やり直してください。 3. System Setup Main Menu(セットアップユーティリティメインメニュー)画面で、System BIOS(システム BIOS)をクリッ クします。 4. System BIOS(システム BIOS)画面で Serial Communication(シリアル通信)をクリックします。 関連参照文献 シリアル通信 、p. 62 関連タスク シリアル通信の詳細 、p.
オプション 説明 ら BIOS のデフォルト設定をロードしても、この設定がシリアルデバイス 1 のデフォルト設定に戻らない 場合があります。 Failsafe Baud Rate コンソールのリダイレクトに使用されているフェイルセーフボーレートが表示されます。BIOS は自動的にボ (フェイルセーフボ ーレートの決定を試みます。このフェイルセーフボーレートは、その試みが失敗した場合にのみ使用されま ーレート) す。また、値は変更しないでください。デフォルトでは、このオプションは 115200 に設定されています。 Remote Terminal リモートコンソールターミナルのタイプを設定します。このオプションは、デフォルトで VT 100/VT 220 Type(リモートター に設定されています。 ミナルタイプ) Redirection After OS のロード時に BIOS コンソールのリダイレクトの有効または無効を切り替えることができます。このオ Boot(起動後のリダ プションは、デフォルトで Enabled(有効)に設定されています。 イレクト) 関連参照文献 シリアル通信 、p.
関連タスク システムプロファイル設定の詳細 、p.
オプション 説明 Processor 1(プロ セッサ 1 のターボ ブースト対応コア 数) プロセッサ 1 のターボブースト対応コア数を制御します。コアの最大数がデフォルトで有効にします。 Monitor/Mwait プロセッサ内の Monitor/Mwait 命令を有効にします。このオプションは、デフォルトで Custom(カスタ ム)以外のすべてのシステムプロファイルに対して Enabled(有効)に設定されています。 メモ: このオプションは、Custom(カスタム)モードの C States(C ステート) オプションが Disabled (無効)に設定されている場合に限り、無効に設定できます。 メモ: Custom(カスタム)モードで C States(C ステート) が Enabled(有効)に設定されている場合 に、Monitor/Mwait 設定を変更しても、システムの電力またはパフォーマンスは影響を受けません。 関連参照文献 システムプロファイル設定 、p. 64 関連タスク システムプロファイル設定の表示 、p.
その他の設定の詳細 このタスクについて Miscellaneous Settings(その他の設定)画面の詳細は、次のとおりです。 オプション 説明 System Time(シス システムの時刻を設定することができます。 テム時刻) System Date(シス システムの日付を設定することができます。 テム日付) Asset Tag(管理タ 資産タグを指定して、セキュリティと追跡のために変更することができます。 グ) Keyboard NumLock が有効または無効のどちらの状態でシステムが起動するかを設定できます。デフォルトでは、この NumLock(キーボー オプションは On(オン)に設定されています。 ド NumLock) メモ: このフィールドは 84 キーのキーボードには適用されません。 F1/F2 Prompt on エラー時の F1/F2 プロンプトを有効または無効にします。このオプションは、デフォルトで Enabled(有効) Error(エラー時 F1/ に設定されています。F1/F2 プロンプトは、キーボードエラーも含みます。 F2 プロンプト) Load Legacy Vid
関連参照文献 システム BIOS 、p. 43 関連タスク iDRAC 設定ユーティリティの起動 、p. 68 温度設定の変更 、p. 68 iDRAC 設定ユーティリティの起動 手順 1. 管理対象システムの電源を入れるか、再起動します。 2. Power-on Self-test(POST)中に を押します。 3. System Setup Main Menu(セットアップユーティリティメインメニュー) ページで iDRAC Settings(iDRAC 設定)をクリッ クします。 iDRAC Settings(iDRAC 設定)画面が表示されます。 関連参照文献 iDRAC 設定ユーティリティ 、p. 67 温度設定の変更 iDRAC 設定ユーティリティでは、お使いのシステムの温度制御設定を選択してカスタマイズすることができます。 1. iDRAC Settings(iDRAC 設定) > Thermal(温度) の順にクリックします。 2.
組み込み型システム管理 Dell Lifecycle Controller により、システムのライフサイクル全体を通して、高度な組み込み型システムを管理できるようになりま す。Dell Lifecycle Controller は起動時にも開始することができ、オペレーティングシステムに依存せずに機能します。 メモ: 一部のプラットフォーム構成では、Dell Lifecycle Controller の提供する機能の一部がサポートされない場合があります。 Dell Lifecycle Controller のセットアップ、ハードウェアとファームウェアの設定、およびオペレーティングシステムの導入の詳細に ついては、Dell.com/idracmanuals の『Dell Lifecycle Controller マニュアル』を参照してください。 関連参照文献 Dell Lifecycle Controller 、p. 68 ブートマネージャ Boot Manager(起動マネージャ)画面では、起動オプションと診断ユーティリティを選択できます。 関連参照文献 起動マネージャのメインメニュー 、p.
メニュー項目 説明 Launch System セットアップユーティリティにアクセスできます。 Setup(セットアッ プユーティリティ の起動) Launch Lifecycle 起動マネージャを終了し、Dell Lifecycle Controller プログラムを起動します。 Controller (Lifecycle Controller の起動) System Utilities (システムユーティ リティ) システム診断および UEFI シェルなどのシステムユーティリティメニューを起動できます。 関連参照文献 ブートマネージャ 、p. 69 関連タスク ブートマネージャの表示 、p. 69 ワンショット BIOS 起動メニュー One-shot BIOS boot menu(ワンショット BIOS 起動メニュー)では、起動元となる起動デバイスを選択することができます。 関連参照文献 ブートマネージャ 、p.
7 システムコンポーネントの取り付けと取り外し 本項には、システムコンポーネントの取り付けおよび取り外しに関する情報が記載されています。 トピック: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • タワー型からラック型への変換に関する安全手順 システム内部の作業を始める前に システム内部の作業を終えた後に 推奨ツール 前面ベゼル(オプション) システムスタビライザ キャスターホイール - オプション システムカバー システム内部 冷却エアフローカバー 冷却ファン 冷却ファンアセンブリ(オプション) システムメモリ フレックスベイ ハードドライブ 光学ドライブとテープドライブ 内蔵 USB メモリキー(オプション) 拡張カードホルダ 拡張カード GPU カードホルダ(オプション) GPU カード(オプション) 内蔵デュアル SD モジュール(オプション) 内蔵 SD カード プロセッサとヒートシンク 電源装置ユニット システムバッテリー ハードドライブバックプレーン SD vFlash カード(オプション) コントロールパネルア
ラックモードのシステムの安定性と安全性については、以下の注意事項を守ってください。 ● 機器をラックに取り付ける前に、前面と側面のラックスタビライザを取り付けてください。スタビライザを取り付けないと、 ラックが転倒するおそれがあります。 ● 取り付けは常に一番重い物を最初に、下から上の順序で行います。 ● ラックに電力を供給する AC 分岐回路に過剰な負担をかけないでください。 システム内部の作業を始める前に 前提条件 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1. システムとすべての周辺機器の電源を切ります。 2. システムを電源コンセントと周辺機器から外します。 3. 前面ベゼルが取り付けられている場合は、取り外します。 4. 必要に応じて、システムをラックから取り外します。 詳細については、Dell.com/poweredgemanuals のラック取り付けプレースマットを参照してください。 5. システムを横置きにします。 6. システムのカバーを外します。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p.
● ベゼルロックのキー。 キーは、お使いのシステムにベゼルが含まれている場合にのみ必要となります。 ● #2 プラスドライバ ● 静電気防止用リストバンド DC 電源装置ユニットのケーブルの組み立てには、次の工具が必要です。 ● AMP 90871-1 圧着ハンドツールまたは同等のツール ● Tyco Electronics 58433-3 または同等のもの ● サイズ 10 AWG ソリッドワイヤ、または絶縁銅撚線から絶縁材を除去するためのワイヤストリッパープライヤ メモ: アルファワイヤパーツナンバー 3080 または同等のもの(65/30 より線)を使用します。 前面ベゼル(オプション) 前面ベゼルはシステムの前面に取り付けてあり、ハードドライブの取り外し中、またはリセットボタンや電源ボタンを押したとき の事故を防止します。前面ベゼルは、セキュリティ強化のためにロックすることもできます。 オプションの前面ベゼルの取り外し 手順 1. ベゼルキーを使ってベゼルのロックを解除します。 メモ: 2 個のベゼルキーがベゼルの背面に接続されています。 2. ベゼル上部のリリースラッチを押します。 3.
3. リリースラッチ 4. システム 次の手順 オプションの前面ベゼルを取り付けます。 関連概念 オプションの前面ベゼルの取り付け 、p. 74 オプションの前面ベゼルの取り付け 手順 1. ベゼルキーの位置を確認して取り外します。 メモ: 2 個のベゼルキーがベゼルの背面に接続されています。 2. ベゼルタブをシャーシのベゼルタブスロットに挿入します。 3. リリースラッチを押して、ベゼルが所定の位置にロックされるまで、ベゼルをシステムに向かって押します。 4. キーを使用してベゼルをロックします。 図 16. 前面ベゼルの取り付け a. ベゼルキー b. ベゼル c. システム 関連概念 オプションの前面ベゼルの取り外し 、p.
システムスタビライザ システムスタビライザーは、タワーモードのシステムを安定させます。 システムスタビライザの取り外し 前提条件 メモ: システムをタワーモードからラックモードに変える場合、またはシステムスタビライザをホイールアセンブリに交換する 場合にのみ、システムスタビライザを取り外すことをお勧めします。 1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 #2 プラスドライバを準備しておきます。 システムスタビライザーを内側に回します。 システムを安定した平面に横向きに置きます。 手順 システムスタビライザをタワーのベースに固定しているネジを取り外します。 図 17. システムスタビライザの取り外しと取り付け 1. タブスロット(12) 3. タブ(12) 5. システムスタビライザ(4) 2. ネジ穴(4) 4. タワーのベース 6. ネジ(4) 関連概念 システムスタビライザの取り付け 、p. 76 関連参照文献 タワー型からラック型への変換に関する安全手順 、p.
システムスタビライザの取り付け 前提条件 注意: スタンドアロンタワーシステムを安定させるには、スタビライザを取り付ける必要があります。スタビライザを取り付け ないと、システムが転倒して、場合によってはけがやシステムの損傷を招くおそれがあります。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 3. システムを安定した平面に横向きに置きます。 手順 1. システムスタビライザの 3 つのタブをシャーシ基部の 3 つのスロットの位置に合わせます。 2. システムスタビライザをシャーシ基部にネジで固定します。 次の手順 システムを安定した平面にまっすぐに立てて、システムスタビライザを外側に開きます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システムスタビライザの取り外し 、p.
図 18. キャスターホイールの取り外し 1. タワーのベースのスロット(4) 3. ネジ(2) 2. ホイールアセンブリユニット(2) 4. サポートユニットのネジ(2) 5. サポートユニット 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク キャスターホイールの取り付け 、p. 77 キャスターホイールの取り付け 前提条件 1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 #2 プラスドライバを準備しておきます。 システムを安定した平面に横向きに置いて、システムのベースが平面の端から出た状態にします。 システムスタビライザが取り付けてある場合は、取り外します。詳細については、「システムスタビライザの取り外し」の項を 参照してください。 手順 1.
2. 背面ホイールをシステムの背面に向けて少しずらし、1 本のネジでユニットを所定の位置に固定します。 3. 前面ホイールの 2 つの固定フックを、シャーシ基部の 2 つのスロットに合わせて差し込みます。 4. 前面ホイールを前面に向けて少しずらし、1 本のネジでユニットを所定の位置に固定します。 図 19. キャスターホイールの取り付け 1. タワーのベースのスロット(4) 3. ネジ(2) 2. ホイールアセンブリユニット(2) 4. サポートユニットのネジ(2) 5. サポートユニット 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システムスタビライザの取り外し 、p. 75 キャスターホイールの取り外し 、p.
システムカバーの取り外し 前提条件 1. 2. 3. 4. 5. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 システムおよび接続されているすべての周辺機器の電源を切ります。 システムを電源コンセントと周辺機器から外します。 前面ベゼルが取り付けられている場合は、取り外します。 システムを平らで安定した面におきます。 手順 1. ラッチリリースロックをロック解除位置に回します。 2. カバーリリースラッチを押してシステムカバーを取り外します。 図 20. システムカバーの取り外し 1. システム 3. カバーリリースラッチ 2. システムカバー 4. カバーリリースラッチロック 次の手順 1. 2. 3. 4. システムカバーを取り付けます。 システムをまっすぐに立てて、安定した平面に置きます。 周辺機器を再度接続し、システムをコンセントに接続します。 システムとすべての周辺機器の電源を入れます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システムカバーの取り付け 、p.
システムカバーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. すべての内部ケーブルが接続され、邪魔にならないように束ねられており、システム内部に工具や余分な部品が残っていないこ とを確認します。 手順 1. システムカバーのスロットをシャーシのタブに合わせます。 2. カバーリリースラッチを押して、ラッチが所定の位置にロックされるまで、カバーをシャーシの方に押します。 3. ラッチリリースロックを時計方向に回してロック位置にします。 図 21. システムカバーの取り付け 1. システム 3. カバーリリースラッチ 2. システムカバー 4. カバーリリースラッチロック 次の手順 1. 2. 3. 4. 5.
システム内部 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 図 22. システム内部 1. 3. 5. 7. 9. 11. 13. 15. 冷却ファンアセンブリの冷却ファン(オプション) 冷却用エアフローカバーの位置合わせガイド プロセッサ 2 拡張カードホルダ 冷却用エアフローカバーの冷却ファン(2) 拡張カードホルダ DIMM スロット(6) ハードドライブバックプレーン 2. 4. 6. 8. 10. 12. 14.
冷却エアフローカバー 冷却エアフローカバーは、システム全体にわたって空気力学的に空気の流れを導きます。空気の流れは、システムのすべての重要 なパーツを通過します。減圧により、ヒートシンクの表面領域全体で空気が引き込まれ、冷却効果が向上します。 冷却エアフローカバーの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 注意: エア フロー カバーを取り外した状態でシステムを使用しないでください。システムが急激にオーバーヒートする可能性 があり、システムのシャットダウンや、データ損失の原因となります。 1. 「安全にお使いいただくために」の項に記載されている安全ガイドラインに従ってください。 2.
関連タスク システム内部の作業を始める前に 、p. 72 オプションの冷却ファンアセンブリの取り外し 、p. 86 冷却エアフローカバーの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. 該当する場合は、シャーシ側面に沿ってシステム内部にケーブルを配線し、ケーブル保持ブラケットを使ってケーブルを固定し ます。 手順 1. 冷却エアフローカバーのタブをシャーシの固定スロットに合わせます。 2.
関連タスク システム内部の作業を始める前に 、p. 72 冷却ファン お使いのシステムには、冷却用エアフローカバー上に 2 台の冷却ファンと、4 台の冷却ファンを格納するオプションの冷却ファン アセンブリが搭載されています。 メモ: それぞれのファンは、システム管理ソフトウェアに記載され、各ファン番号で参照されます。特定のファンに問題が発 生した場合は、冷却ファンアセンブリ上のファン番号をメモしておくことで、容易に識別し適切なファンに交換できます。 冷却ファンの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2.
b. ファンリリースタブ c. 冷却ファン 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 冷却ファンの取り付け 、p. 85 システム内部の作業を終えた後に 、p. 72 冷却ファンの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: 冷却ファンアセンブリおよび冷却用エアフローカバーに個々のファンを取り付ける手順は、同じです。 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1. 冷却ファンコネクタをシステム基板のコネクタに合わせます。 2.
次の手順 1. 冷却ファンアセンブリ 2. ファンリリースタブ 3. 冷却ファン 4. システム基板上の冷却ファンコネクタ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p.
図 27. 冷却ファンアセンブリの取り外し a. 冷却ファンアセンブリ b. 冷却ファン(4) c. リリースレバー(2) 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 オプションの冷却ファンアセンブリの取り付け 、p.
図 28. 冷却ファンアセンブリの取り付け 1. 冷却ファンアセンブリ 3. リリースレバー(2) 5. ガイドピン(6) 2. 冷却ファン(4) 4. スロット(6) 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク オプションの冷却ファンアセンブリの取り外し 、p. 86 システム内部の作業を終えた後に 、p.
図 29. メモリソケットの位置 メモリチャネルの構成は次のとおりです。 表 28. メモリチャネル プロセッサ チャネル 0 チャネル 1 チャネル 2 チャネル 3 プロセッサ スロット A1、A5、および A9 スロット A2、A6、および 1 A10 スロット A3、A7、および A11 スロット A4、A8、および A12 プロセッサ スロット B1、B5、および B9 スロット B2、B6、および 2 B10 スロット B3、B7、および B11 スロット B4、B8、および B12 次の表は、サポートされている構成のメモリ装着と動作周波数を示しています。 表 29.
メモリー モジュール取り付けガイドライン メモ: メモリ構成がガイドラインに沿っていない場合、システムが起動しなかったり、メモリ構成中に反応しなくなったり、 少ないメモリで動作したりすることがあります。 このシステムは柔軟なメモリー構成をサポートしているため、あらゆる有効なチップセット アーキテクチャ構成でシステムを構成 し、実行することができます。次に、メモリー モジュールの設定に関する推奨ガイドラインを示します。 ● RDIMM と LRDIMM を併用しないでください。 ● x4 および x8 DRAM ベースのメモリー モジュールは併用できます。詳細については、「モードごとのガイドライン」の項を参照し てください。 ● デュアルまたはシングルランク RDIMM をチャネルごとに 3 枚まで装着できます。 ● ランクカウントに関係なく、LRDIMM は 3 枚まで装着できます。 ● 速度の異なるメモリモジュールを取り付けた場合は、取り付けられているメモリモジュールのうちで最も遅いものの速度で動作 します。または、システムの DIMM 構成によってはさらに遅い動作になります。 ● プロセッサーが取り付けら
メモリ スペアリングを有効にすると、オペレーティング システムに使用できるシステムメモリはチャネルごとに 1 ランク少なくな ります。たとえば、4 GB のシングル ランク メモリ モジュールを 16 個使用するデュアル プロセッサー構成では、利用可能なシステ ムメモリは 16(メモリ モジュール)× 4 GB = 64 GB とはならず、3/4(ランク/チャネル)× 16(メモリ モジュール)× 4 GB = 48 GB となります。 メモ: メモリスペアリングは、マルチビットの修正不能なエラーには対応できません。 メモ: アドバンス ECC/ロックステップ モードとオプティマイザー モードは、メモリ スペアリングをサポートしています。 メモリミラーリング メモリ ミラーリングは他のどのモードよりもメモリ モジュールの信頼性に優れており、修正不能なマルチ ビットのエラーに対応す る機能が向上しています。ミラーリング構成では、使用可能なシステムメモリの総量は取り付けられた総物理メモリの 2 分の 1 で す。取り付けられたメモリの半分は、アクティブな DIMM のミラーリングに使用されます。修正不能なエラー
表 31.
表 32.
メモリモジュールの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 2. 3. 4.
メモ: メモリモジュールを取り外したままにする場合は、メモリモジュールのダミーカードを取り付けます。 2. 冷却エアフローカバーを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 オプションの冷却ファンアセンブリの取り外し 、p. 86 メモリモジュールの取り付け 、p.
図 31. メモリモジュールの取り付け a. メモリモジュール b. 位置合わせキー c. メモリモジュールソケットのイジェクタ(2) 次の手順 1. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 2. を押してセットアップユーティリティを起動し、System Memory(システムメモリ)設定を確認します。 システムの値は、増設されたメモリを反映して変更済みになっています。 3. 値が正しくない場合、1 つ、または複数のメモリモジュールが適切に取り付けられていない可能性があります。メモリモジュー ルがメモリモジュールソケットに確実に装着されているようにします。 4. システム診断プログラムでシステムメモリのテストを実行します。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 メモリモジュールの取り外し 、p. 94 オプションの冷却ファンアセンブリの取り外し 、p. 86 フレックスベイ お使いのシステムのフレックスベイは、16 台の 2.
3. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. ケーブルを外します。 a. 2.5 インチドライブのフレックスベイの場合は、スリム光学ドライブとバックプレーンからケーブルを外します。 b. Dell PowerEdge Express Flash デバイスのフレックスベイの場合は、バックプレーンからケーブルを外します。 2. フレックスベイをシャーシに固定している 2 本のネジを外します。 3. リリースラッチを押し、フレックスベイをシャーシから引き出します。 図 32. フレックスベイの取り外し 1. フレックスベイ 3.
注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. フレックスベイのタブをシャーシ前面のスロットに合わせます。 2. タブが所定の位置に固定されるまで、フレックスベイをシャーシに挿入します。 3. 2 本のネジを取り付けてフレックスベイをシャーシに固定します。 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 33. フレックスベイの取り付け 1. フレックスベイ 3. ネジ穴(2) 5. ネジ(2) 2. タブ(3) 4. リリースラッチ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p.
メモ: Enterprise クラスのハードドライブをエントリーハードドライブと併用しないでください。 右側のドライブタイプの選択は、使用パターンに応じて異なります。不適切なエントリーハードドライブの使用(年間 55 TB を超 える作業負荷率)は大きなリスクにつながり、ドライブ故障率を増加させます。 これらのハードドライブに関する詳細は、Dell.
図 34. ホットスワップ対応ハードドライブまたは SSD の取り外し a. リリースボタン b. ハードドライブまたは SSD キャリア c. ハードドライブまたは SSD キャリアのハンドル 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 オプションの前面ベゼルの取り外し 、p.
手順 1. ハードドライブダミーがハードドライブスロットに取り付けられている場合は、取り外してください。 2. ハードドライブキャリアにハードドライブを取り付けます。詳細については、「ホット スワップ対応ハード ドライブ キャリアー へのホット スワップ対応ハード ドライブの取り付け」の項を参照してください。 3. ハードドライブキャリア前面のリリースボタンを押して、ハードドライブキャリアのハンドルを開きます。 4. ハードドライブキャリアがバックプレーンに接続されるまで、キャリアをハードドライブスロットに挿入します。 5. ハードドライブのキャリアハンドルを閉じて、ハードドライブを所定の位置にロックします。 次の手順 オプションの前面ベゼルを取り付けます。 図 35. ホットスワップ対応ハードドライブの取り付け 1. リリースボタン 2. ハードドライブまたは SSD キャリア 3. ハードドライブまたは SSD キャリアのハンドル 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 2.
図 36. 2.5 インチハードドライブダミーの取り外し a. ハードドライブダミー b. リリースボタン 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 2.5 インチハードドライブダミーの取り付け 、p. 102 2.5 インチハードドライブダミーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 前面ベゼルが取り付けられている場合は、取り外します。 手順 リリースボタンが所定の位置にカチッと収まるまで、ハードドライブダミーをハードドライブスロットに差し込みます。 図 37. 2.5 インチハードドライブダミーの取り付け a. ハードドライブダミー 次の手順 前面ベゼルを取り外した場合は、取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p.
関連タスク 2.5 インチハードドライブダミーの取り外し 、p. 101 3.5 インチハードドライブダミーの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。デルで認められていない修理(内部作業)による損傷は、保証の対象となりません。製品に 付属しているマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 注意: システムの正常な冷却状態を維持するために、空のハードドライブスロットすべてにハードドライブダミーを取り付ける 必要があります。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 前面ベゼルが取り付けられている場合は、取り外します。 手順 リリースボタンを押して、ダミーをハードドライブスロットから引き出します。 図 38. 3.5 インチハードドライブダミーの取り外し a.
手順 リリースボタンが所定の位置にカチッと収まるまで、ハードドライブダミーをハードドライブスロットに差し込みます。 図 39. 3.5 インチハードドライブダミーの取り付け a. ハードドライブダミー 次の手順 前面ベゼルを取り外した場合は、取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 3.5 インチハードドライブアダプタへの 2.5 インチハードドライブの取り 付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 3.
図 40. 3.5 インチハードドライブアダプタへの 2.5 インチハードドライブの取り付け a. 3.5 インチハードドライブアダプタ b. ネジ(2) c. 2.5 インチハードドライブ 次の手順 3.5 インチアダプタを 3.5 インチハードドライブキャリアに取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 3.5 インチハードドライブアダプタからの 2.5 インチハードドライブの取り外し 、p. 105 3.5 インチハードドライブアダプタからの 2.5 インチハードドライブの取 り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。デルで認められていない修理(内部作業)による損傷は、保証の対象となりません。製品に 付属しているマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1.
図 41. 3.5 インチハードドライブアダプタからの 2.5 インチハードドライブの取り外し a. 3.5 インチハードドライブアダプタ b. ネジ(2) c. 2.5 インチハードドライブ 次の手順 3.5 インチハードドライブアダプタに 2.5 インチハードドライブを取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 3.5 インチハードドライブアダプタへの 2.5 インチハードドライブの取り付け 、p. 104 ホットスワップ対応ハードドライブキャリアへの 3.5 インチハードドラ イブアダプタの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1.
図 42. ホットスワップ対応ハードドライブキャリアへの 3.5 インチハードドライブアダプタの取り付け 1. 3.5 インチハードドライブキャリア 3. ハードドライブ アダプタ 2. ネジ(5) 4. 2.5 インチハードドライブ 次の手順 1. ホットスワップ対応ハードドライブキャリアをシステムに取り付けます。 2. 前面ベゼルを取り外した場合は、取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク ホットスワップ対応 3.5 インチハードドライブキャリアからのホットスワップ対応 3.5 インチハードドライブアダプタの取り外 し 、p. 107 ホットスワップ対応 3.5 インチハードドライブキャリアからのホットス ワップ対応 3.
図 43. ホットスワップ対応 3.5 インチハードドライブキャリアからのホットスワップ対応 3.5 インチハードドライブアダプタ の取り外し 1. 3.5 インチハードドライブキャリア 3. ハードドライブ アダプタ 2. ネジ(5) 4. 2.5 インチハードドライブ 次の手順 前面ベゼルを取り外した場合は、取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク ホットスワップ対応ハードドライブキャリアへの 3.5 インチハードドライブアダプタの取り付け 、p. 106 ハード ドライブキャリアーからのハード ドライブまたはソリッドステー トドライブの取り外し 前提条件 1. #1 プラスドライバを準備しておきます。 2. システムからホット スワップ対応ハード ドライブ キャリアーを取り外します。 手順 1. ハード ドライブキャリアーのスライドレールからネジを外します。 2. ハード ドライブを持ち上げてハード ドライブキャリアーから取り出します。 図 44. ハード ドライブキャリアーからのハード ドライブの取り外し a. ネジ(4) b.
次の手順 該当する場合は、ハード ドライブをハード ドライブキャリアーに取り付けます。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 ホットスワップ対応ハードドライブキャリアへのホットスワップ対応ハ ードドライブの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: ホットスワップ対応ハードドライブは、ハードドライブスロットに収まるホットスワップ対応ハードドライブキャリアに 装着されて提供されます。 1. #2 プラスドライバを準備しておきます。 2. ホットスワップ対応ハードドライブキャリアを取り外します。 手順 1.
光学ドライブとテープドライブ お使いのシステムでは、以下のいずれかの構成がサポートされています。 表 33. システム設定 システム 構成 3.5 インチハードドライブを最大 8 台、2.5 インチハードドライ ブを最大 16 台搭載できるシステム 最大 3 台の SATA ハーフハイトの光学ドライブ 最大 3 台の SATA/SAS/SCSI テープドライブ 光学ドライブとテープドライブの組み合わせ 3.5 インチハードドライブ最大 8 台、2.5 インチハードドライブ 最大 1 台の SATA ハーフハイト光学ドライブ キャリア内の 3.5 インチハードドライブ最大 8 台、または 2.5 イ SATA/SAS/SCSI テープドライブ 1 台まで ンチハードドライブ 16 台と PCIe SSD 4 台を搭載するシステム 3.5 インチハードドライブを最大 18 台搭載できるシステム 1 台の光学ドライブまたはテープドライブ 2.
図 46. 光学ドライブまたはテープドライブの取り外し a. 光学ドライブ / テープドライブ b. ガイド c.
図 47. ケーブル接続 — 光学ドライブとテープドライブ 1. システム基板の ODD1/TBU コネクタ 3. 内蔵テープアダプタの mini-SAS/SATA コネクタ 2. システム基板の ODD2/TBU コネクタ 4. 内蔵テープアダプタ 5. システム基板 6. SAS テープドライブ 7. 光学ドライブ 2 8. 光学ドライブ 1 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 光学ドライブまたはテープドライブの取り付け 、p.
光学ドライブまたはテープドライブの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 手順 1. ドライブをパッケージから取り出して、取り付けの準備をします。 手順については、ドライブに同梱のマニュアルを参照してください。 SAS テープドライブを取り付ける場合は、内蔵テープアダプタが取り付けられている必要があります。SAS テープドライブの取 り付けの詳細については、「拡張カードの取り付け」の項を参照してください。 2.
次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 拡張カードの取り付け 、p. 121 システム内部の作業を終えた後に 、p. 72 スリム光学ドライブダミーの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 手順 1.
スリム光学ドライブダミーの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載されている安全手順に従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 手順 1. スリム光学ドライブダミーをスリム光学ドライブベイに揃えます。 2. ロックが所定の位置に固定されるまで、光学ドライブダミーを光学ドライブベイに挿入します。 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 50. スリム光学ドライブダミーの取り付け 1. スリム光学ドライブダミー 2.
内蔵 USB ポートは、System Setup(セットアップユーティリティ)の Integrated Devices(内蔵デバイス)画面にある Internal USB Port(内蔵 USB ポート)オプションで有効にする必要があります。 メモ: システム基板上の内蔵 USB ポート(INT_USB) の位置を確認するには、「システム基板のジャンパとコネクタ」の項を参照 してください。 オプションの内蔵 USB メモリー キーの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載されている安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載されている手順に従います。 手順 1. システム ボードの USB ポートまたは USB メモリー キーの位置を確認します。 USB ポートの位置を確認するには、「システム基板のジャンパとコネクタ」「」の項を参照してください。 2. USB メモリー キーを取り付けている場合は、USB ポートから取り外します。 図 51. 内蔵 USB メモリー キーの取り外し a. USB メモリー キー b. USB ポート 3.
関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 拡張カードホルダ 拡張カードホルダの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 タブを押し、拡張カードホルダをシャーシから引き出します。 図 53. 拡張カードホルダの取り外し a. タブ b.
拡張カードホルダの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 拡張カードホルダをシャーシのプロジェクションに合わせ、しっかりと装着されるまで押し下げます。 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 54. 拡張カードホルダの取り付け 1. タブ 2. 拡張カードホルダ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p. 72 拡張カードホルダの取り外し 、p.
表 34.
表 35.
メモ: システムの FCC 認可を維持するために、空の拡張カードスロットにフィラーブラケットを取り付ける必要がありま す。ブラケットには、システム内へのごみやほこりの侵入を防ぐほか、システム内部の正常な冷却と換気を助ける役割も あります。 図 55. 拡張カードの取り外し a. 拡張カードラッチ b. 拡張カード c. 拡張カードコネクタ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 拡張カードの取り付け 、p. 121 拡張カードの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3.
メモ: 将来使用するためにブラケットを保管しておきます。システムの FCC 認可規格を維持するには、空の拡張カードスロ ットにフィラーブラケットを取り付ける必要があります。ブラケットには、システム内へのごみやほこりの侵入を防ぐほ か、システム内部の正常な冷却と換気を助ける役割もあります。 4. カードの両端を持ち、カードエッジコネクタを拡張カードコネクタに合わせます。 5. カードが完全に装着されるまで、カードエッジコネクタを拡張カードコネクタにしっかりと挿入します。 6. ラッチが所定の位置に収まるまで、ラッチを押し上げて拡張カードラッチを閉じます。 7. 拡張カードにすべてのケーブルを接続します。 8. 拡張カードホルダを交換します。 次の手順 1. 拡張カードホルダを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 56. 拡張カードの取り付け a. 拡張カードラッチ b. 拡張カード c. 拡張カードコネクタ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p.
注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 リリースタブを押し、GPU カードホルダをシャーシから引き出します。 図 57. GPU カードホルダの取り外し a. リリースタブ b. GPU カードホルダ 次の手順 1. 冷却用エアフローカバーを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク オプションの GPU カードホルダの取り付け 、p. 123 システム内部の作業を始める前に 、p. 72 冷却エアフローカバーの取り外し 、p.
手順 GPU カードホルダをシャーシのスロットとガイドピンに合わせ、しっかり装着されるまで GPU カードホルダを押し下げます。 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 58. GPU カードホルダの取り付け 1. ガイドピン 2. リリースタブ 3. GPU カードホルダ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p. 72 オプションの GPU カードホルダの取り外し 、p.
● スロット 6 と 7 を使用するには、両方のプロセッサを取り付ける必要があります。 ● シングル プロセッサー構成ではダブルワイド GPU カードを 2 枚、デュアル プロセッサー構成ではダブルワイド GPU カードを 4 枚取り付けます。 ● GPGPU カード 4 枚構成の場合、内蔵スロットでサポートできるのは 1 つの PERC のみです。 ● デュアルプロセッサ構成での 4 つのダブルワイド 300 W GPU カード(Intel 3120A または Intel 7120A)、またはシングルプロセッ サ構成での 2 つのダブルワイド 300 W GPU カード(Intel 3120A または Intel 7120A)は、30°C を超える環境温度では動作させる ことができません。 ● 3.
図 59. GPU カードの取り外し 1. 拡張カードラッチ(2) 3. SLI データコネクタ 5. GPU カード電源コネクタ 2. GPU カード 4. GPU カード電源コネクタ 6. x16 コネクタ 次の手順 1. 次の手順を行って、フィラーブラケットを取り付けます。 2. 3. 4. 5. a. フィラーブラケットのスロットを拡張カードスロットのタブに合わせます。 b. 拡張カードラッチをフィラーブラケットが所定の位置にロックされるまで押します。 メモ: システムの FCC 認可を維持するために、空の拡張カードスロットにフィラーブラケットを取り付ける必要があり ます。ブラケットには、システム内へのごみやほこりの侵入を防ぐほか、システム内部の正常な冷却と換気を助ける役 割もあります。 ラッチが所定の位置に収まるまでラッチを押し込んで、2 つの拡張カードラッチを閉じます。 拡張カードホルダを交換します。 冷却用エアフローカバーを取り付けます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p.
1. 2. 3. 4. 5. 6. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 冷却シュラウドを取り外します。 拡張カードホルダを取り外します。 2 つの拡張カードラッチを開きます。 フィラーブラケットを取り外します。 メモ: このブラケットは今後の使用のために保存しておいてください。フィラーブラケットは、システムの FCC 認証を維持 するために空の拡張カード スロットに取り付ける必要があります。また、ブラケットもゴミや埃からシステムを保護し、 システム内部の適正な冷却と通気を助けます。 図 60. GPU カードの取り付け 1. 拡張カードラッチ(2) 3. SLI データコネクタ 5. GPU カード電源コネクタ 2. GPU カード 4. GPU カード電源コネクタ 6. x16 コネクタ 手順 1. システム基板の x16 スロットの位置を確認します。 2. GPU カードをスロットに挿入します。 3. PIB から GPU カードにケーブルを接続します。 4.
オプションの GPU カードの取り外し 、p. 125 拡張カードホルダの取り外し 、p.
表 36. IDSDM インジケータコード 表記規則 IDSDM インジケータコード 説明 A 緑色 カードがオンラインであることを示します。 B 緑色の点滅 再構築またはアクティビティを示します。 C 橙色の点滅 カードの不一致またはカードに障害が発生したことを示しま す。 D 橙色 カードがオフライン、故障している、または書き込みが禁止 されていることを示します。 E 消灯 カードが取り付けられていないか、起動していないことを示 します。 次の手順 1. IDSDM をインストールします。 2. 取り外した場合は、SD カードを取り付けます。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 オプションの内蔵デュアル SD モジュールの取り付け 、p.
関連タスク システム内部の作業を始める前に 、p. 72 内蔵 SD カード 内蔵 SD カードの取り外し 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: 各 SD カードに、取り外す前の対応するスロット番号のラベルを一時的に貼り付けてください。SD カードを再度取り付け る際は、その対応するスロットに取り付けます。 手順 内蔵デュアル SD モジュール上の SD カードスロットの位置を確認し、カードを押してスロットから外します。 図 62.
関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク オプションの内蔵デュアル SD モジュールの取り付け 、p. 129 システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 内蔵 SD カードの取り付け 前提条件 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3.
図 63. 内蔵 SD カードの取り付け 1. IDSDM 3. SD カード 1 5. SD カードスロット 2 2. SD カード 2 4. SD カードスロット 1 次の手順 「システム内部の作業を終えた後に」の項に記載された手順に従います。 プロセッサとヒートシンク 次の作業は下記の手順に従って行ってください。 ● ヒートシンクの取り外しと取り付け ● 追加のプロセッサの取り付け ● プロセッサの交換 メモ: 正常な冷却状態を維持するために、空のプロセッサソケットすべてにプロセッサダミーを取り付ける必要があります。 ヒートシンクの取り外し 前提条件 注意: プロセッサを取り外す場合を除き、ヒートシンクをプロセッサから取り外さないでください。ヒートシンクは適切な温度 条件を保つために必要です。 警告: ヒートシンクは高温で触れません。システムの電源を切った後、時間を取って、ヒートシンクを冷却してください。 1. 2. 3. 4.
5. 冷却エアフローカバーを取り外します。 6. #2 プラスドライバを準備しておきます。 手順 1. ヒートシンクをシステム基板に固定しているネジのうち 1 つを緩めます。 ヒートシンクとプロセッサの接着が緩むまで、30 秒程待ちます。 2. 最初に取り外したネジの筋向いのネジを取り外します。 3. 手順 1 と 2 を繰り返して、残りの 2 つのネジを取り外します。 4. ヒートシンクを取り外します。 図 64. ヒートシンクの取り外し 1. ヒートシンク 3. 固定ネジスロット(4) 2. 固定ネジ(4) 4. プロセッサソケット 次の手順 1. ヒートシンクおよびプロセッサを取り付けます。 2. プロセッサーとヒートシンクを交換します。 3. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 ヒートシンクの取り付け 、p.
メモ: これは、フィールド交換可能ユニット(FRU)です。取り外しおよび取り付け手順は、デル認証のサービス技術者のみが 行う必要があります。 メモ: システムをアップグレードする場合は、Dell.com/support から最新バージョンのシステム BIOS をダウンロードし、圧縮 されたダウンロード ファイルに説明されている手順に従い、システムにアップデートをインストールします。 メモ: システム BIOS のアップデートは Dell Lifecycle Controller を使用して行えます。 メモ: システムの正常な冷却状態を維持するために、空のプロセッサー ソケットすべてにプロセッサー ダミーを取り付ける必 要があります。 1. 2. 3. 4. 5. 6.
図 65. プロセッサシールド 1. クローズファーストソケットリリースレバー 3. プロセッサ 5. アンロックアイコン 2. ロックアイコン 4.
図 66. プロセッサの取り外し 1. 3. 5. 7. クローズファーストソケットリリースレバー プロセッサ プロセッサシールド ソケット 2. 4. 6. 8. プロセッサのピン 1 インジケータ スロット(4) オープンファーストソケットリリースレバー ソケットキー(4) 次の手順 1. 2. 3. 4. プロセッサを取り付けます。 ヒートシンクを取り付けます。 冷却用エアフローカバーを取り付けます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 プロセッサの取り付け 、p.
1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 #2 プラスドライバを準備しておきます。 システムをアップグレードする場合は、最新バージョンのシステム BIOS を Dell.com/support からダウンロードします。次に、 圧縮されたダウンロードファイルで説明されている手順に従い、お使いのシステムにアップデートをインストールします。 メモ: Dell Lifecycle Controller を使用してシステム BIOS をアップデートすることも可能です。 5. 冷却ファンアセンブリが取り付けられている場合は、取り外します。 6. フルレングス PCIe カードが取り付けられている場合は、取り外します。 7. 冷却エアフローカバーを取り外します。 メモ: 必要に応じて、冷却エアフローカバー上の拡張カードラッチを閉じ、フルレングスカードを外します。 8. ケーブルが接続されている場合は、拡張カードから外します。 9.
図 67. プロセッサの取り付け 1. 3. 5. 7. ソケットリリースレバー 1 プロセッサ プロセッサシールド プロセッサソケット 2. 4. 6. 8. プロセッサのピン 1 の角 スロット(4) ソケットリリースレバー 2 タブ(4) 次の手順 メモ: プロセッサを取り付けた後は、必ずヒートシンクを取り付けてください。ヒートシンクは適切な温度条件を保つために必 要です。 ヒートシンクを取り付けます。 PCIe 拡張カードライザーが取り外されている場合は、再度取り付けます。 ケーブルが外されている場合は、拡張カードに再度接続します。 「システム内部の作業を終えた後に」に記載された手順に従います。 起動時に F2 を押してセットアップユーティリティを起動し、プロセッサの情報が新しいシステム構成と一致していることを確 認します。 6. システム診断プログラムを実行し、新しいプロセッサが正しく動作することを確認します。 1. 2. 3. 4. 5. 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 冷却エアフローカバーの取り外し 、p.
ヒートシンクの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 2. 3. 4. 5. 6. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 「システム内部の作業を始める前に」の項に記載された手順に従います。 冷却ファンアセンブリが取り付けられている場合は、取り外します。 フルレングス PCIe カードが取り付けられている場合は、取り外します。 プロセッサーを取り付けます。 #2 プラスドライバを準備しておきます。 手順 1. 既存のヒートシンクを使用している場合は、糸くずの出ない清潔な布で、ヒートシンクからサーマルグリースを拭き取ります。 2.
5. 残りの 2 本のネジについても同じ手順を繰り返します。 図 69. ヒートシンクの取り付け 1. ヒートシンク 2. 固定ネジ(4) 3. 固定ネジスロット(4) 4. プロセッサソケット 次の手順 該当する場合、PCIe カードを取り付けます。 冷却ファンアセンブリを取り外した場合は、取り付けます。 「システム内部の作業を終えた後に」の項に記載された手順に従います。 起動時に F2 を押してセットアップユーティリティを起動し、プロセッサの情報が新しいシステム構成と一致していることを確 認します。 5. システム診断プログラムを実行し、新しいプロセッサが正しく動作することを確認します。 1. 2. 3. 4. 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 オプションの冷却ファンアセンブリの取り外し 、p. 86 プロセッサの取り付け 、p.
メモ: 2 台の同一 PSU を取り付けると、システム BIOS で電源装置の冗長性(冗長性を伴う 1+1、または冗長性を伴わない 2+0) が設定されます。冗長モードでは、ホット スペアが無効になっているときに両方の PSU からシステムに半分ずつ電力が供給さ れます。ホット スペアが有効な場合、システムの効率性を最大化するために、システムの使用率が低いときにはいずれかの PSU がスタンバイになります。 メモ: AC 電源装置については、拡張電源パフォーマンス(EPP)ラベルが背面に貼付されている電源装置のみを使用してくだ さい。旧世代のサーバーからの電源装置を混在させると、電源装置の不整合が発生し、電源が入らなくなる可能性があります。 メモ: お使いのシステムに取り付けられている GPU カードが 2 枚を超えている場合は、1100 W PSU を 2 台取り付ける必要があ ります。 ホットスペア機能 お使いのシステムではホットスペア機能がサポートされており、電源装置ユニット(PSU)の冗長性に関連する電力のオーバーヘッ ドが大幅に軽減されます。 ホットスペア機能を有効に設定すると、冗長 PSU のう
図 70. AC PSU の取り外し 1. リリースラッチ 3. PSU 5. PSU ハンドル 2. PSU ケーブルコネクタ 4. 電源コネクタ 次の手順 ● 該当する場合は、AC PSU を取り付けます。 ● 該当する場合は、PSU ダミーを取り付けます。 関連タスク AC 電源装置ユニットの取り付け 、p. 142 AC 電源装置ユニットの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: 最大出力電力(ワット数で表記)は PSU ラベルに記載されています。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2.
ります。新しい PSU が他の PSU を取り外す前に検出され、有効にするまで待機します。電源装置ステータスインジケータ が緑色に点灯すれば、電源装置は正常に機能しています。 図 71. AC PSU の取り付け 1. リリースラッチ 3. PSU 5. PSU ハンドル 2. PSU ケーブルコネクタ 4. 電源コネクタ 関連タスク AC 電源装置ユニットの取り外し 、p.
必要なツール サイズ 10 AWG ソリッドワイヤ、または絶縁銅撚線から絶縁材を除去できるワイヤストリッパープライヤ メモ: アルファワイヤパーツナンバー 3080 または同等のもの(65/30 より線)を使用します。 必要なワイヤ ● UL 10 AWG、最長 2 m(より線)ブラックワイヤ 1 本 [– 48 / 60 V DC] ● UL 10 AWG、最長 2 m(より線)レッドワイヤ 1 本(V DC リターン) ● UL 10 AWG、最長 2 m(より線)緑 / 黄、緑に黄縞ワイヤ 1 本(アース端子付き) 安全用接地線の組み立てと接続 前提条件 メモ: DC–(48~60)V 電源装置ユニット(PSU)を使用する装置の DC 電源接続およびアース接続は、適切な資格を持つ電気 技術者が行う必要があります。DC 電源またはアースの接続はご自分で行わないでください。すべての電気接続は、システムの 使用地域およびその国の条例と慣行に準拠する必要があります。Dell の許可を受けていない保守による損傷は、保証の対象と なりません。製品に同梱の安全にお使いいただくための注意をすべてお読みになり、指示に
DC 入力電源ワイヤの組み立て 前提条件 メモ: DC–(48~60)V 電源装置ユニット(PSU)を使用する装置の DC 電源接続およびアース接続は、適切な資格を持つ電気 技術者が行う必要があります。DC 電源またはアースの接続はご自分で行わないでください。すべての電気接続は、システムの 使用地域およびその国の条例と慣行に準拠する必要があります。Dell の許可を受けていない保守による損傷は、保証の対象と なりません。製品に同梱の安全にお使いいただくための注意をすべてお読みになり、指示に従ってください。 手順 1. DC 電源ワイヤの端から絶縁材を剥がし、銅製ワイヤを約 13 mm(0.5 インチ)ほど露出させます。 メモ: DC 電源ワイヤを接続する際に極を逆にすると、電源装置またはシステムに修復不能な損傷を与えるおそれがありま す。 2. 銅線の両端を組み合わせコネクタに挿入し、#2 プラスドライバを使用して組み合わせコネクタ上部の固定ネジを締めます。 メモ: 電源装置を静電気放出から保護するため、組み合わせコネクタを電源装置に挿入する前に、固定ネジにラバーキャッ プを被せてください。 3.
使用地域およびその国の条例と慣行に準拠する必要があります。Dell の許可を受けていない保守による損傷は、保証の対象と なりません。製品に同梱の安全にお使いいただくための注意をすべてお読みになり、指示に従ってください。 注意: システムが正常に動作するには、PSU が 1 台は必要です。冗長電源が装備されたシステムでも、システムに電源が入っ た状態で一度に取り外しと取り付けができる PSU は 1 台だけです。 メモ: 電源ユニットの取り外しに支障がある場合は、ラッチを外してオプションのケーブルマネージメントアームを持ち上げる 必要があります。ケーブル管理アームの情報については、お使いのシステムのラック マニュアルを参照してください。 手順 1. 電源から電源ケーブルを外し、取り外そうとしている PSU からコネクタを外します。 2. アース端子付きワイヤを外します。 3. リリースラッチを押し、PSU ハンドルを使用して PSU をシャーシから引き出します。 図 74. DC PSU の取り外し 1. リリースラッチ 3. PSU 5. PSU ハンドル 2. 電源装置ステータスインジケータ 4.
メモ: 最大出力電力(ワット数で表記)は PSU ラベルに記載されています。 手順 1. PSU が完全に装着され、リリースラッチが所定の位置にカチッとおさまるまで、PSU をシャーシに差し込みます。 メモ: ケーブル管理アームのラッチをかけている場合は、再びラッチをかけます。ケーブル管理アームの詳細については、ラ ックに関するマニュアルを参照してください。 2. アース端子付きワイヤを接続します。 3. PSU に DC 電源コネクタを取り付けます。 注意: 電源ワイヤを接続するときは、必ずストラップでワイヤを PSU ハンドルに固定してください。 4. DC 電源にワイヤを接続します。 メモ: 新しい PSU の通常の取り付けや、ホットスワップまたはホットアッドによって交換または取り付けを行う際には、 システムが PSU を認識して状態を判断するまで 15 秒待ちます。電源装置ステータスインジケータが緑色に点灯すれば、電 源装置は正常に機能しています。 図 75. DC PSU の取り付け 1. リリースラッチ 3. PSU 5. PSU ハンドル 2. 電源装置ステータスインジケータ 4.
前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 2 台目の電源装置ユニット(PSU)を取り付ける場合は、PSU ダミーを外側へ引いて、ベイから取り外します。 注意: 非冗長構成の場合は、システムの正常な冷却状態を維持するために、2 つ目の PSU ベイに PSU ダミーを取り付ける必要 があります。PSU ダミーは、2 台目の PSU を取り付ける場合にのみ取り外します。 図 76. PSU ダミーの取り外し a. PSU ダミー b.
手順 電源装置ユニットダミーを電源装置ユニットスロットに合わせて、所定の位置にカチッと収まるまでダミーを電源装置ユニットス ロットに押し込みます。 図 77. PSU ダミーの取り付け a. PSU ダミー b. PSU ベイ 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 電源装置ユニットダミーの取り外し 、p.
注意: バッテリの取り付け、取り外しの際には、バッテリコネクタが破損しないようにしっかり支えてください。 2. バッテリコネクタのマイナス側の固定タブの間に指を置き、バッテリを持ち上げてソケットから取り外します。 図 78. システムバッテリの取り外し a. システムバッテリ b. システムバッテリスロット 3. 新しいシステムバッテリを取り付けるには、プラス側を上にしてバッテリを持ち、固定タブの下に挿入します。 4. 所定の位置に収まるまでバッテリをコネクタに押し込みます。 図 79. システムバッテリの取り付け a. システムバッテリ b. システムバッテリスロット 次の手順 1. 冷却エアフローカバーを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 3. 起動中に F2 を押して System Setup(セットアップユーティリティ)を起動し、バッテリが正常に動作していることを確認しま す。 4. セットアップユーティリティの Time(時刻)および Date(日付)フィールドで正しい時刻と日付を入力します。 5.
ハードドライブバックプレーン お使いのシステムは、構成に応じて以下のいずれかをサポートします。 ● ● ● ● ● 3.5 インチ x8 SAS/SATA バックプレーン 3.5 インチ x18 SAS/SATA バックプレーン 2.5 インチ x4 Dell PowerEdge Express Flash(PCIe SSD)バックプレーン 2.5 インチ x16 SAS/SATA バックプレーン 2.5 インチ x32 SAS/SATA バックプレーン お使いのシステムは、構成に応じて以下のバックプレーンの組み合わせのいずれかをサポートします。 ● 3.5 インチ x8 SAS/SATA バックプレーンと 2.5 インチ x4 PCIe SSD バックプレーン ● 2.5 インチ x16 SAS/SATA バックプレーンと 2.5 インチ x4 PCIe SSD バックプレーン ● ハードドライブベイ内のハードドライブ用 2.5 インチ x16 SAS/SATA バックプレーン、およびフレックスベイ内のハードドライ ブ用 2.
図 80. PCIe SSD ハードドライブバックプレーンの取り外し 1. 3. 5. 7. 9. リリースタブ ハードドライブコネクタ 電源ケーブル バックプレーンの電源コネクタ バックプレーンの PCIe ケーブルコネクタ 2. 4. 6. 8. PCIe SSD ハードドライブバックプレーン PCIe ケーブル 信号ケーブル バックプレーンの信号ケーブルコネクタ 図 81. 3.5 インチ(x8)SAS/SATA バックプレーンの取り外し 1. SAS ケーブル 3. バックプレーン電源コネクタ 5. リリースピン 152 システムコンポーネントの取り付けと取り外し 2. x8 バックプレーン 4. バックプレーン電源ケーブル 6.
図 82. ケーブル配線 — 3.5 インチ(x8)SAS/SATA バックプレーン 1. システム基板の SAS A コネクタ 2. システム基板の SAS B コネクタ 3. システム基板 4. システム基板の信号コネクタ 5. x8 バックプレーン 6. バックプレーンの信号コネクタ 7. バックプレーンの SAS B コネクタ 8.
図 83. シングル PERC カードを搭載した 3.5 インチ(x8)SAS/SATA バックプレーンの取り外し 1. SAS ケーブル 3. 電源コネクタ 5. リリースピン 154 システムコンポーネントの取り付けと取り外し 2. x8 バックプレーン 4. 電源ケーブル 6.
図 84. ケーブル配線 — シングル PERC カードを搭載した 3.5 インチ(x8)SAS/SATA バックプレーン 1. 3. 5. 7. 9. PERC カードの SAS B コネクタ PERC カード システム基板の信号コネクタ バックプレーンの信号コネクタ バックプレーンの SAS A コネクタ 2. 4. 6. 8.
図 85. 3.5 インチ(x8)+ 2.5 インチ(x4)SAS/SATA バックプレーンの取り外し 1. x8 バックプレーン電源ケーブル 3. x8 バックプレーン 2. x8 バックプレーンの電源コネクタ 4. リリースピン 5. x8 バックプレーンの SAS ケーブル 6. x8 バックプレーンの信号ケーブル 7. PCIe SSD バックプレーンの電源ケーブル 8. PCIe SSD バックプレーンの PCIe ケーブル 9. PCIe SSD バックプレーンの信号ケーブル 10. PCIe SSD バックプレーンの電源コネクタ 11. PCIe SSD バックプレーンの信号コネクタ 12. PCIe SSD バックプレーン 13.
図 86. ケーブル配線 — 3.5 インチ(x8)+ 2.5 インチ(x4)SAS/SATA バックプレーン 1. PCIe SSD バックプレーンの PCIe C コネクタ 2. PCIe SSD バックプレーンの PCIe B コネクタ 3. PCIe SSD バックプレーンの PCIe A コネクタ 4. PCIe SSD バックプレーンの信号コネクタ 5. PERC カード上の 3.5 インチバックプレーンからの SAS B ケ 6. PERC カード上の 3.5 インチバックプレーンからの SAS A ケ ーブル ーブル 7. PCIe SSD バックプレーンから PCIe エクステンダカードへの 8. PCIe SSD バックプレーンから PCIe エクステンダカードへの PCIe C コネクタ PCIe A コネクタ 9. PCIe SSD バックプレーンから PCIe エクステンダカードへの 10. PCIe SSD バックプレーンから PCIe エクステンダカードへの PCIe D コネクタ PCIe B コネクタ 11. PCIe ブリッジカード 12.
21. PCIe SSD バックプレーン 図 87. 3.5 インチ(x18)SAS/SATA バックプレーンの取り外し 1. x18 バックプレーン 3. リリースピン 5. 電源コネクタ 158 システムコンポーネントの取り付けと取り外し 2. 信号ケーブル 4. 電源ケーブル 6.
図 88. ケーブル配線 — 3.5 インチ(x18)SAS/SATA バックプレーン 1. PERC カードの SAS B コネクタ 3. PERC カード 5. システム基板の信号コネクタ 2. PERC カードの SAS A コネクタ 4. システム基板 6. バックプレーンの SAS A コネクタ 7. バックプレーンの SAS B コネクタ 9. バックプレーンの信号コネクタ 8.
図 89. 2.5 インチ(x16)SAS/SATA バックプレーンの取り外し 1. x16 バックプレーン 3. 信号ケーブル 5. 電源ケーブル 160 システムコンポーネントの取り付けと取り外し 2. リリースピン 4. 電源コネクタ 6.
図 90. ケーブル配線 — 2.5 インチ(x16)SAS/SATA バックプレーン 1. 3. 5. 7. 9. PERC カードの SAS B コネクタ PERC カード システム基板の信号コネクタ バックプレーンの SAS A コネクタ バックプレーンの信号コネクタ 2. 4. 6. 8.
図 91. 2.5 インチ(x16)+ 2.5 インチ(x4)SAS/SATA バックプレーンの取り外し 1. x16 バックプレーン 2. リリースピン 3. x16 バックプレーンの信号ケーブル 5. x16 バックプレーンへの電源ケーブル 7. PCle SSD バックプレーンへの電源ケーブル 4. x16 バックプレーンの電源コネクタ 6. x16 バックプレーンへの SAS ケーブル 8. PCle SSD バックプレーンへの PCIe ケーブル 9. PCle SSD バックプレーンへの信号ケーブル 10. PCIe SSD バックプレーンの電源コネクタ 11. PCIe SSD バックプレーンの信号コネクタ 12. PCIe SSD バックプレーン 13.
図 92. ケーブル配線 — 2.5 インチ(x16)+ 2.5 インチ(x4)SAS/SATA バックプレーン 1. PCIe SSD バックプレーンの PCIe C コネクタ 2. PCIe SSD バックプレーンの PCIe B コネクタ 3. PCIe SSD バックプレーンの PCIe A コネクタ 4. PCIe SSD バックプレーンの信号コネクタ 5. PERC カード上の 2.5 インチバックプレーンからの SAS B ケ 6. PERC カード上の 2.5 インチバックプレーンからの SAS A ケ ーブル ーブル 7. PCIe SSD バックプレーンから PCIe エクステンダカードへの 8. PCIe SSD バックプレーンから PCIe エクステンダカードへの PCIe C コネクタ PCIe A コネクタ 9. PCIe SSD バックプレーンから PCIe エクステンダカードへの 10. PCIe SSD バックプレーンから PCIe エクステンダカードへの PCIe D コネクタ PCIe B コネクタ 11. PCIe ブリッジカード 12.
21. PCIe SSD バックプレーン 図 93. PERC カード 2 枚を搭載した 2.5 インチ(x32)SAS/SATA バックプレーンの取り外し 1. リリースピン 2. バックプレーン 2 の信号ケーブル 3. バックプレーン 2 の電源コネクタ 4. バックプレーン 2 への電源ケーブル 5. バックプレーン 2 への SAS ケーブル 6. バックプレーン 1 の信号ケーブル 7. バックプレーン 1 の電源コネクタ 8. バックプレーン 1 への電源ケーブル 9. バックプレーン 1 への SAS ケーブル 10. バックプレーン 1 11.
図 94. ケーブル配線 — PERC カード 2 枚を搭載した 2.5 インチ(x32)SAS/SATA バックプレーン 1. 3. 5. 7. 9. 11. 13. 15. 17. バックプレーン 2 の信号コネクタ バックプレーン 2 の SAS A コネクタ PERC 1 上の SAS A コネクタ PERC 2 上の SAS A コネクタ PERC カード 1 システム基板のバックプレーン 2 からの信号ケーブル バックプレーン 1 の SAS B コネクタ バックプレーン 1 バックプレーン 2 2. 4. 6. 8. 10. 12. 14. 16.
図 95. シングル PERC カードを搭載した 2.5 インチ(x32)SAS/SATA バックプレーンの取り外し 1. リリースピン 2. バックプレーン 2 の信号ケーブル 3. バックプレーン 2 の電源コネクタ 4. バックプレーン 2 への電源ケーブル 5. バックプレーン 2 への SAS ケーブル 6. バックプレーン 1 の信号ケーブル 7. バックプレーン 1 の電源コネクタ 8. バックプレーン 1 への電源ケーブル 9. バックプレーン 1 への SAS ケーブル 10. x16 バックプレーン 1 11. バックプレーン 2 の SAS コネクタ 12.
図 96. ケーブル配線 — シングル PERC カードを搭載した 2.5 インチ(x32)SAS/SATA バックプレーン 1. バックプレーン 2 の信号コネクタ 3. バックプレーン 2 の SAS A コネクタ 2. バックプレーン 2 の SAS B コネクタ 4. PERC カードの SAS B コネクタ 5. PERC カードの SAS A コネクタ 6. x32 PERC カード 7. システム基板 8. システム基板のバックプレーン 2 信号コネクタ 9. システム基板のバックプレーン 1 信号コネクタ 10. バックプレーン 1 の SAS B コネクタ 11. バックプレーン 1 の SAS A コネクタ 12. バックプレーン 1 13. バックプレーン 1 の信号コネクタ 14. バックプレーン 2 の SAS B1 コネクタ 15. バックプレーン 2 の SAS A1 コネクタ 16. バックプレーン 2 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p.
オプションの冷却ファンアセンブリの取り外し 、p. 86 ハードドライブバックプレーンの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載された手順に従います。 3. すべてのハードドライブを取り外します。詳細については、「ホットスワップ対応ハードドライブの取り外し」の項を参照してく ださい。 4. 冷却ファンアセンブリが取り付けられている場合は、取り外します。詳細については、「冷却ファンアセンブリの取り外し(オ プション)」の項を参照してください。 5.
図 97. PCIe SSD ハードドライブバックプレーンの取り付け 1. PCIe SSD ハードドライブバックプレーン 2. PCIe SSD ハードドライブコネクタ 3. PCIe ケーブル 4. 電源ケーブル 5. 信号ケーブル 6. バックプレーンの電源コネクタ 7. バックプレーンの信号ケーブルコネクタ 8. バックプレーンの PCIe ケーブルコネクタ 図 98. 3.5 インチ(x8)SAS/SATA バックプレーンの取り付け 1. SAS ケーブル 2. x8 バックプレーン 3. バックプレーン電源コネクタ 4. バックプレーン電源ケーブル 5. リリースピン 6.
図 99. シングル PERC カードを搭載した 3.5 インチ(x8)SAS/SATA バックプレーンの取り付け 1. SAS ケーブル 2. x8 バックプレーン 3. 電源コネクタ 4. 電源ケーブル 5. リリースピン 6. 信号ケーブル 図 100. 3.5 インチ(x8)+ 2.5 インチ(x4)SAS/SATA バックプレーンの取り付け 1. x8 バックプレーン電源ケーブル 3. x8 バックプレーン 2. x8 バックプレーンの電源コネクタ 4. リリースピン 5. x8 バックプレーンの SAS ケーブル 7. PCIe SSD バックプレーンの電源ケーブル 6. x8 バックプレーンの信号ケーブル 8.
9. PCIe SSD バックプレーンの信号ケーブル 11. PCIe SSD バックプレーンの信号コネクタ 10. PCIe SSD バックプレーンの電源コネクタ 12. PCIe SSD バックプレーン 図 101. 3.5 インチ(x18)SAS/SATA バックプレーンの取り付け 1. x18 バックプレーン 2. 信号ケーブル 3. リリースピン 4. 電源ケーブル 5. 電源コネクタ 6. SAS ケーブル 図 102. 2.5 インチ(x16)SAS/SATA バックプレーンの取り付け 1. x16 バックプレーン 2.
3. 信号ケーブル 5. 電源ケーブル 4. 電源コネクタ 6. SAS ケーブル 図 103. 2.5 インチ(x16)+ 2.5 インチ(x4)SAS/SATA バックプレーンの取り付け 1. x16 バックプレーン 2. リリースピン 3. x16 バックプレーンの信号ケーブル 5. x16 バックプレーンの電源ケーブル 7. PCle SSD バックプレーンの電源ケーブル 4. x16 バックプレーンの電源コネクタ 6. x16 バックプレーンの SAS ケーブル 8. PCle SSD バックプレーンの PCIe ケーブル 9. PCle SSD バックプレーンの信号ケーブル 10. PCIe SSD バックプレーンの電源コネクタ 11. PCIe SSD バックプレーンの信号コネクタ 12.
図 104. PERC カード 2 枚を搭載した 2.5 インチ(x32)SAS/SATA バックプレーンの取り付け 1. リリースピン 2. バックプレーン 2 の信号ケーブル 3. バックプレーン 2 の電源コネクタ 4. バックプレーン 2 の電源ケーブル 5. バックプレーン 2 の SAS ケーブル 6. バックプレーン 1 の信号ケーブル 7. バックプレーン 1 の電源コネクタ 8. バックプレーン 1 の電源ケーブル 9. バックプレーン 1 の SAS ケーブル 10. x16 バックプレーン 1 11.
図 105. シングル PERC カードを搭載した 2.5 インチ(x32)SAS/SATA バックプレーンの取り付け 1. リリースピン 2. バックプレーン 2 の信号ケーブル 3. バックプレーン 2 の電源コネクタ 4. バックプレーン 2 の電源ケーブル 5. バックプレーン 2 の SAS ケーブル 6. バックプレーン 1 の信号ケーブル 7. バックプレーン 1 の電源コネクタ 8. バックプレーン 1 の電源ケーブル 9. バックプレーン 1 の SAS ケーブル 10. x16 バックプレーン 1 11. バックプレーン 2 の SAS コネクタ 12. x16 バックプレーン 2 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム内部の作業を終えた後に 、p. 72 ホットスワップ対応ハードドライブまたはソリッドステートドライブの取り外し 、p. 99 冷却エアフローカバーの取り付け 、p. 83 オプションの冷却ファンアセンブリの取り付け 、p.
オプションの SD vFlash メディアカードの交換 手順 1. システムの SD vFlash メディアスロットの位置を確認します。 2. SD vFlash メディアカードを取り出すには、カードを押し込んでロックを解除し、カード スロットから引き出します。 図 106. SD vFlash メディアカードの取り外し a. SD vFlash メディアカード b. SD vFlash メディアカード スロット 3. SD vFlash メディアカードを取り付けるには、ラベル側を上に向けて、SD vFlash メディアカードの接続ピン側をモジュールのカ ード スロットに挿入します。 メモ: スロットは正しい方向にしかカードを挿入できないように設計されています。 4. カードを中に押し込んでスロットに固定します。 図 107. SD vFlash メディアカードの取り付け a. SD vFlash メディアカード b. SD vFlash メディアカード スロット コントロールパネルアセンブリ コントロールパネルアセンブリの取り外し 前提条件 1. 2. 3. 4.
注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. コントロールパネルをシャーシに固定しているネジを取り外します。 2. コントロールパネルケーブルとコントロールパネル USB ケーブルをシステム基板から外します。 注意: コントロールパネルケーブルを外す際に無理な力を加えないように注意してください。コネクタが損傷するおそれが あります。 3. コントロールパネルをシャーシから引き出します。 メモ: ラックモード設定のコントロールパネルを取り外すには、同じ手順を実行します。 図 108. コントロールパネルアセンブリの取り外し 1. コントロールパネル 3. コントロールパネル USB ケーブル 2.
ii. タブ iii. スロット 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 コントロールパネルアセンブリの取り付け 、p. 177 コントロールパネルアセンブリの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 手順 1.
図 111. 情報タグの取り付け a. 情報タグ b. タブ c. スロット 3. コントロールパネルケーブルとコントロールパネル USB ケーブルをコントロールパネルアセンブリに接続します。 4. コントロールパネルをシャーシのコントロールパネルスロットに合わせ、挿入します。 5. ネジを使ってコントロールパネルをシャーシに固定します。 6. コントロールパネルケーブルとコントロールパネル USB ケーブルをシステム基板に接続します。 次の手順 1. 冷却ファンアセンブリを取り外した場合は、取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p. 72 オプションの冷却ファンアセンブリの取り付け 、p.
1. 2. 3. 4. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 #2 プラスドライバを準備しておきます。 「システム内部の作業を始める前に」の項に記載された手順に従います。 以下を取り外します。 a. b. c. d. e. f. g. h. i. PCIe カードホルダ 冷却用エアフローカバー 冷却ファンアセンブリ(取り付けられている場合) 内蔵ストレージコントローラカード 内蔵デュアル SD モジュール 内蔵 USB キー(取り付けられている場合) ヒートシンク プロセッサ メモ: 不具合のあるシステム基板を交換する際には、プロセッサピンへの損傷を防ぐため、プロセッサ保護キャップで プロセッサソケットをカバーするようにしてください。 メモリモジュール 手順 1. システム基板からすべてのケーブルを外します。 注意: システム基板をシャーシから取り外す際には、システム識別ボタンに損傷を与えないように注意してください。 2. ポストを持って青色のリリースピンを引き、システム基板をシステムの前面方向にスライドさせます。 3.
図 112. システム基板の取り外し a. ポスト b. システム基板 c. リリースピン 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム基板の取り付け 、p. 180 システム基板の取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 3.
手順 1. 新しいシステム基板アセンブリのパッケージを開きます。 注意: システム基板は、メモリモジュール、プロセッサ、またはその他のコンポーネントを持って持ち上げないでください。 2. ポストを持ち、システム基板を傾けて、システム基板をシャーシ内に下ろします。 3. システム基板のポートが、対応するシャーシのスロットの位置に合うように、システム基板をシャーシの後方に押します。 次の手順 1. Trusted Platform Module(TPM)を取り付けます。TPM の取り付け方法の詳細については、「TPM の取り付け」の項を参照して ください。TPM についての情報は、「Trusted Platform モジュール」の項を参照してください。 2. 次の装置を取り付けます。 3. 4. 5. 6. a. プロセッサとヒートシンク b. 内蔵 USB キー(取り付けられている場合) c. 内蔵デュアル SD モジュール d. 内蔵ストレージコントローラカード e. 冷却ファンアセンブリ(取り付けられている場合) f. 冷却用エアフローカバー g.
図 113. システム基板の取り付け a. ポスト b. システム基板 c. リリースピン 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 Trusted Platform Module の取り付け 、p. 183 システム セットアップを使用したシステム サービス タグの入力 Easy Restore(簡単な復元)がサービス タグの復元に失敗した場合は、システム セットアップユーティリティーを使用してサービス タグを入力します。 手順 1. システムの電源をオンにします。 2. F2 キーを押して System Setup(セットアップユーティリティー)を起動します。 3. サービス タグ設定をクリックします。 4. サービス タグを入力します。 メモ: サービス タグ(サービス タグ)フィールドが空白の場合のみ、サービス タグを入力できます。正しいサービス タグを 入力してください。一度サービス タグが入力されると、更新または変更できません。 5.
6. 新規または既存の iDRAC Enterprise ライセンスをインポートします。 詳細については、www.dell.com/poweredgemanuals で Integrated Dell Remote Access Controller ユーザーズ ガイドを参照してくだ さい。 簡易復元機能を使用したサービスタグの復元 簡易復元機能を使用すると、システム基板を交換した後もお使いのサービスタグ、ライセンス、UEFI 構成、およびシステムの設定 データを復元できます。すべてのデータは自動的にバックアップフラッシュデバイスに自動的にバックアップされます。BIOS が バックフラッシュデバイスで新しいシステム基板とサービスタグを検知したら、BIOS がユーザーにバックアップ情報を復元するプ ロンプトを表示します。 手順 1. システムの電源を入れます。 BIOS が新しいシステム基板を検出した場合、またサービスタグがバックアップフラッシュデバイスにある場合、BIOS はサービ スタグ、ライセンスのステータス、および UEFI 診断 バージョンを表示します。 2.
手順 1. システム ボードの TPM コネクタの位置を確認します。 メモ: システム基板上の TPM コネクタを見つけるには、「システム基板コネクタ」の項を参照してください。 2. TPM のエッジコネクタを TPM コネクタのスロットの位置に合わせます。 3. プラスチック製のリベットがシステム ボードのスロットに合うように、TPM を TPM コネクタに挿入します。 4. 所定の位置に収まるまでプラスチック製のリベットを押します。 図 114. TPM の取り付け 1. システム基板上のリベットスロット 3. TPM 2. プラスチック製リベット 4. TPM コネクター 次の手順 1. システム ボードを取り付けます。 2. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 BitLocker ユーザー向け TPM の初期化 手順 TPM を初期化します。 TPM の初期化の詳細については、https://technet.microsoft.
5. 設定を保存します。 6. システムを再起動します。 7. System Setup(セットアップユーティリティ)を再起動します。 8. System Setup Main Menu(セットアップユーティリティメインメニュー) 画面で、System BIOS(システム BIOS) > System Security Settings(システムセキュリティ設定) をクリックします。 9. Intel TXT(Intel TXT )オプションで、On(オン)を選択します。 電源インタポーザボードと配電基板 電源インタポーザボードの取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1.
c. 配電基板 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 システム基板の取り外し 、p. 178 電源インタポーザボードの取り付け 、p. 188 配電基板の取り外し 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 3.
図 116. 配電基板の取り外し a. ネジ(6) b. 配電基板 関連概念 配電基板の取り付け 、p. 187 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を始める前に 、p. 72 配電基板の取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 1. 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 2. #2 プラスドライバを準備しておきます。 手順 1. 配電基板(PDB)のネジ穴をシャーシの穴の位置に合わせます。 2. 6 本のネジを使って PDB をシャーシに固定します。 3.
6. PCIe カードホルダを取り付けます。 7. 電源装置モジュールを元の位置に取り付けます。 8. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 117. 配電基板の取り付け 1. ネジ(6) 2. 配電基板 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク システム内部の作業を終えた後に 、p. 72 配電基板の取り外し 、p. 186 電源インタポーザボードの取り付け 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 「安全にお使いいただくために」の項に記載された安全ガイドラインに従ってください。 手順 1.
6. 電源装置モジュールを元の位置に取り付けます。 7. 「システム内部の作業を終えた後に」の項に記載された手順に従います。 図 118. 電源インタポーザボードの取り付け 1. 電源インタポーザボード 2. 配電基板 関連参照文献 タワー型からラック型への変換に関する安全手順 、p. 71 関連タスク 電源インタポーザボードの取り付け 、p. 188 システム内部の作業を終えた後に 、p.
8 システム診断プログラムの使用 システムに問題が起こった場合、デルのテクニカルサポートに電話する前にシステム診断プログラムを実行してください。システ ム診断プログラムを使うと、特別な装置を使用せずにシステムのハードウェアをテストでき、データが失われる心配もありません。 お客様がご自分で問題を解決できない場合でも、サービスおよびサポート担当者が診断プログラムの結果を使って問題解決の手助 けを行うことができます。 メモ: OEM 診断イベント メッセージの詳細については、『Event and Error Message Reference Guide for 13th Generation Dell PowerEdge Servers Version 1.
システム診断プログラムのコントロール メニュー 説明 Configuration 検知された全デバイスの設定およびステータス情報が表示されます。 Results 実行された全テストの結果が表示されます。 システム正常 システムパフォーマンスの現在の概要が表示されます。 Event log システムで実行された全テストの結果のタイムスタンプ付きログが表示されます。少なくとも 1 つのイベ ントの説明が記録されていれば、このログが表示されます。 システム診断プログラムの使用 191
9 ジャンパとコネクタ このトピックでは、ジャンパについての具体的な情報を提供します。また、ジャンパとスイッチに関する基本情報も提供し、シス テム内のさまざまな基板上のコネクタについても説明します。システム基板上のジャンパは、システムパスワードとセットアップ パスワードの無効化を支援します。コンポーネントとケーブルを正しく取り付けるには、システム基板上のコネクタを把握しておく 必要があります。 トピック: • • • システム基板のコネクタ システム基板のジャンパ設定 パスワードを忘れたとき システム基板のコネクタ 図 119. システム基板のジャンパとコネクタ 表 37.
表 37.
表 38. システム基板のジャンパ設定 ジャンパ 設定 PWRD_EN 説明 パスワードリセット機能が有効です(ピン 2~4)。BIOS ローカ ルアクセスは次の AC 電源サイクルでロック解除されます。 パスワードリセット機能が無効です(ピン 4 ~ 6)。 NVRAM_CLR 構成設定が次のシステム起動時に保持されます(ピン 3~5)。 構成設定がシステム起動時にクリアされます(ピン 1~3)。 パスワードを忘れたとき システムのソフトウェアセキュリティ機能として、システムパスワードとセットアップパスワードがあります。パスワードジャンパ を使用すると、パスワード機能を有効または無効にしたり、現在使用中の任意のパスワードをクリアしたりすることができます。 前提条件 手順 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを取り外します。 3. システム基板ジャンパ上のジャンパを 4 および 6 番ピンから 2 および 4 番ピンに動かします。 4.
10 システムのトラブルシューティング ユーザーとシステムの安全優先 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: ソリューションの検証は工場出荷のハードウェア構成を使用して行われています。 トピック: • • • • • • • • • • • • • • • • • • • • システムの起動エラーのトラブルシューティング 外部接続のトラブルシューティング ビデオサブシステムのトラブルシューティング USB デバイスのトラブルシューティング シリアル入出力デバイスのトラブルシューティング NIC のトラブルシューティング システムが濡れた場合のトラブルシューティング システムが損傷した場合のトラブルシューティン
さらにクエリーがある場合は、グローバル テクニカル サポートに連絡してください。 ビデオサブシステムのトラブルシューティング 前提条件 メモ: iDRAC グラフィカル ユーザー インターフェイス(GUI)の仮想コンソール内のローカル サーバー ビデオ有効オプションが 選択されていることを確認してください。このオプションが選択されていない場合、ローカル ビデオは無効になっています。 メモ: VGA ポートは、ホットプラグ非対応です。 手順 1. モニタへのケーブル接続(電源とディスプレイ)を確認します。 2. システムからモニタへのビデオ インターフェイスのケーブル配線をチェックします。 タスクの結果 テストが正常に終了したら、問題はビデオハードウェアに関連するものではありません。 次の手順 テストに失敗した場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p.
10. USB 3.0 がセットアップ ユーティリティで有効になっているかどうかを確認します。有効な場合は無効にして、システムを再起 動します。 11. システムにアクセスできない場合は、システム内部の NVRAM_CLR ジャンパをリセットし、BIOS をデフォルト設定に戻しま す。「システム ボードのジャンパ設定」の項を参照してください。 12. IDRAC Settings Utility で、USB Management Port Mode が Automatic または Standard OS Use として設定されていること を確認してください。 13. 各 USB デバイスを一度に 1 台ずつ再接続し、電源を入れます。 14. 同じ問題が発生する USB デバイスがあれば、そのデバイスの電源を切り、USB ケーブルを動作確認済みのケーブルと交換して、 デバイスの電源を入れます。 次の手順 すべてのトラブルシューティングが失敗した場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p. 208 シリアル入出力デバイスのトラブルシューティング 前提条件 手順 1.
● 問題が解決しない場合は、スイッチまたはハブ上の別のコネクタを使用してください。 4. 適切なドライバーがインストールされ、プロトコルがバインドされていることを確認します。詳細については、NIC のマニュア ルを参照してください。 5. セットアップユーティリティを起動し、内蔵デバイス 画面で NIC ポートが有効になっていることを確認します。 6. ネットワーク上のすべての NIC、ハブ、およびスイッチが、同じデータ転送スピード、およびデュプレックスに設定されている ことを確認します。詳細については、各ネットワーク デバイスのマニュアルを参照してください。 7. ネットワーク上のすべての NIC、およびスイッチが、同じデータ転送スピード、およびデュプレックスに設定されていることを 確認します。詳細については、各ネットワーク デバイスのマニュアルを参照してください。 8. すべてのネットワーク ケーブルのタイプが適切で、最大長を超えていないことを確認します。 次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p.
次の手順 テストに失敗した場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p. 208 システムが損傷した場合のトラブルシューティング 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 2. システム カバーを取り外します。 3.
メモ: 一部のソフトウェアには、システムの時刻を進めたり遅らせたりするものがあります。システム セットアップによって 設定された時刻以外はシステムが正常に作動しているように見える場合、問題の原因はバッテリーの欠陥ではなく、ソフトウ ェアにあると考えられます。 手順 1. セットアップユーティリティで時刻と日付を再入力します。 2. システムの電源を切り、少なくとも 1 時間はコンセントから外しておきます。 3. システムをコンセントに再接続し、システムの電源を入れます。 4. セットアップユーティリティを起動します。 システム セットアップに表示される日付と時刻が正しくない場合は、システム バッテリーのメッセージに関するシステム エ ラー ログ(SEL)を確認します。 次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p.
電源装置ユニットの問題 手順 1. 接続が緩んでいないことを確認します。 たとえば、電源ケーブルの接続が緩んでいることがあります。 2. 電源装置ユニット(PSU)ハンドルまたは LED が、PSU が正常に動作していることを示していることを確認します。 PSU インジケータの詳細については、「電源インジケータコード」の項を参照してください。 3. 最近システムをアップグレードした場合は、PSU に新しいシステムをサポートするのに十分な電力があるか確認します。 4. 冗長 PSU 構成を使用している場合は、両方の PSU のワット数およびタイプが同じであることを確認してください。 ワット数がより大きな PSU へのアップグレードが必要となる場合もあります。 5. 背面に拡張電源パフォーマンス(EPP)のラベルが貼付されている PSU のみを使用するようにしてください。 6.
修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: ファンの番号は、システム管理ソフトウェアで参照できます。特定のファンに問題が発生した場合に、冷却ファン アセ ンブリー上のファンの番号をメモしておくことで、簡単に識別して交換することができます。 1. 「安全にお使いいただくために」の項に記載されている安全ガイドラインに従ってください。 2. 「システム内部の作業を始める前に」の項に記載されている手順に従います。 手順 1. ファンまたはファンの電源ケーブルを抜き差しします。 2. システムを再起動します。 次の手順 1. 「システム内部の作業を終えた後に」の項に記載されている手順に従います。 2. 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p.
10. セットアップユーティリティを起動して、システムメモリーの設定を確認します。 問題が解決しない場合は、手順 11 に進みます。 11. システム カバーを取り外します。 12. 診断テストまたはエラーメッセージで特定のメモリモジュールに障害があることが発覚した場合、そのモジュールを動作確認済 みのメモリモジュールと取り替え、または交換します。 13. 特定されていないメモリモジュールで障害が発生している場合のトラブルシューティングを行うには、1 番目の DIMM ソケット に装着されているメモリモジュールを同じタイプおよび容量のモジュールと交換します。 画面にエラーメッセージが表示される場合、1 つ以上取り付けられた DIMM のタイプ、誤った DIMM の取り付け、または不良 DIMM 関連の問題である可能性があります。画面上の手順に従って、問題を解決します。 14. システム カバーを取り付けます。 15. システムの起動中、表示されるエラー メッセージ、およびシステム.前面の診断インジケータを観察します。 16.
メモ: IDSDM スロットおよび vFlash スロットは、ホットプラグ非対応です。 手順 1. セットアップユーティリティを起動し、内蔵 SD カードポートが有効になっていることを確認します。 2. システムおよび接続されている各種周辺機器の電源を切り、システムをコンセントから外します。 3. システム カバーを取り外します。 メモ: SD カードに障害が発生すると、内蔵のデュアル SD モジュール コントローラーによりシステムに通知されます。次回 の再起動時に障害を通知するメッセージがシステムにより表示されます。SD カード障害時に冗長性が有効になっている場 合、重要アラートがログに記録され、シャーシの正常性が低下します。 4. 障害が発生した micro SD カードを新しい micro SD カードと交換します。 5. システム カバーを取り付けます。 6. システムをコンセントに接続し、システムの電源を入れます(接続されている各種周辺機器を含む)。 7.
関連参照文献 ヘルプ 、p. 208 ドライブまたは SSD のトラブルシューティング 前提条件 注意: このトラブルシューティング手順により、ドライブに保存されたデータが削除されるおそれがあります。続行する前に、 ドライブ上のすべてのファイルをバックアップしてください。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 手順 1. 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 Diagnostics(診断)テストの結果に応じて、随時次の手順を実行します。 2.
5. 6. 7. 8. 9. 10. 11. 12. 13. 各拡張カードがコネクタに確実に装着されていることを確認します。 システム カバーを取り付けます。 システムをコンセントに再接続し、システムと接続されている周辺機器の電源を入れます。 問題が解決しない場合は、システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 システム カバーを取り外します。 システムに取り付けられている拡張カードをすべて取り外します。 システム カバーを取り付けます。 システムをコンセントに再接続し、システムと接続されている周辺機器の電源を入れます。 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 テストに失敗した場合は、「困ったときは」の項を参照してください。 14. 手順 10 で取り外した各拡張カードについて、次の手順を実行します。 a. b. c. d. e.
d. システム カバーを取り付けます。 e. 適切な診断テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 次の手順 問題が解決しない場合は、「困ったときは」の項を参照してください。 関連参照文献 ヘルプ 、p. 208 プロセッサーのトラブルシューティング 前提条件 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可されている範囲に限 り、またはオンラインサービスもしくは電話サービスとサポートチームの指示によってのみ、トラブルシューティングと簡単な 修理を行うようにしてください。Dell の許可を受けていない保守による損傷は、保証の対象となりません。製品に付属してい るマニュアルの「安全にお使いいただくために」をお読みになり、指示に従ってください。 メモ: プロセッサー ソケットはホットプラグ対応ではありません。 手順 1. 適切な Diagnostics(診断)テストを実行します。「システム診断プログラムの使用」のセクションを参照してください。 2.
11 ヘルプ トピック: Dell EMC へのお問い合わせ マニュアルのフィードバック QRL によるシステム情報へのアクセス UEFI iSCSI 設定 • • • • Dell EMC へのお問い合わせ Dell EMC では、オンラインおよび電話によるサポートとサービス オプションをいくつかご用意しています。お使いのコンピュータ ーがインターネットに接続されていない場合は、購入時の納品書、出荷伝票、請求書、または Dell EMC 製品カタログで連絡先をご 確認ください。これらのサービスは国および製品によって異なり、お住まいの地域では一部のサービスがご利用いただけない場合 があります。Dell EMC のセールス、テクニカル サポート、またはカスタマー サービスへは、次の手順でお問い合わせいただけます。 手順 1. www.dell.com/support/home にアクセスします。 2. お住まいの国を、ページ右下隅のドロップダウンメニューから選択します。 3. カスタマイズされたサポートを利用するには、次の手順に従います。 a.
● 特定のハードウェア構成および保証情報に簡単にアクセスするためのシステムのサービス タグ ● テクニカルサポートや営業チームへのお問い合わせのためのデルへの直接的なリンク 手順 1. www.dell.com/qrl にアクセスして、お使いの製品に移動する、または 2. システム上、または「クイックリソースロケータ」セクションで、お使いのスマートフォンまたはタブレットを使用してモデル固 有のクイックリソース(QR)コードをスキャンします。 PowerEdge T630 の Quick Resource Locator(QRL) UEFI iSCSI 設定 「iSCSI Settings(iSCSI 設定)」画面を使用して、iSCSI デバイスの設定を変更できます。iSCSI 設定オプションは UEFI 起動モードで のみ使用可能です。BIOS 起動モードでは、BIOS はネットワーク設定の制御を行いません。BIOS 起動モードの場合は、ネットワー クコントローラのオプション ROM がネットワーク設定を処理します。 関連参照文献 UEFI iSCSI 設定 、p.