Dell EMC PowerStore 전원 끄기 및 재부팅 절차 안내서 버전 2.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2020 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자 의 상표일 수 있습니다.
목차 추가 리소스.....................................................................................................................................4 장 1: 소개........................................................................................................................................ 5 전원 제어 절차 고려 사항................................................................................................................................................... 5 전원 제어 절차 미리 보기............................................
서문 제품군을 향상시키기 위한 노력의 일환으로 소프트웨어와 하드웨어의 개정 버전을 정기적으로 릴리스하고 있습니다. 이 문서에서 설 명하는 일부 기능은 현재 사용 중인 소프트웨어 또는 하드웨어의 일부 버전에서 지원되지 않을 수 있습니다. 제품 릴리스 노트에는 제 품 기능에 대한 최신 정보가 제공되어 있습니다. 제품이 올바르게 작동하지 않거나 이 문서에 설명된 대로 작동하지 않는 경우 서비스 공급업체에 문의하십시오. 지원 정보 지원, 제품 및 라이선스 정보는 다음과 같이 확인할 수 있습니다. ● 제품 정보 제품 및 기능 설명서 또는 릴리스 노트를 보려면 https://www.dell.com/powerstoredocs에서 PowerStore 설명서 페이지를 참조 바 랍니다. ● 문제 해결 제품, 소프트웨어 업데이트, 라이선스 등록 및 서비스에 대한 자세한 내용은 https://www.dell.com/support에서 해당 제품 지원 페 이지를 참조 바랍니다.
1 소개 이 문서의 절차에 따라 PowerStore 어플라이언스, 노드 또는 클러스터를 정상적으로 끄거나 재부팅합니다. 강력한 재해 복구 계획의 일환으로, 이 절차를 인쇄하고 단계별로 수행하여 계획된 종료 및 재시작 프로세스를 테스트하는 것이 좋습니다. 주제: • • 전원 제어 절차 고려 사항 전원 제어 절차 미리 보기 전원 제어 절차 고려 사항 시작 하기 전에 다음 사항에 유의 하십시오. ● 노드, 어플라이언스 또는 클러스터의 전원을 끄는 데 몇 분 정도 걸릴 수 있습니다. ● 긴급 전원 끄기 상황에서는 캐비닛의 전원 스위치를 꺼짐으로 전환하여 모든 캐비닛 구성 요소의 전원을 즉시 끕니다. ● 하드웨어를 다룰 때는 정전기가 방전되어 하드웨어가 손상될 수 있습니다. 하드웨어를 다루기 전에 교체 가능한 유닛의 처리에 대한 예방 조치를 취하십시오. 교체 가능 유닛 취급 시 안전 예방 조치 페이지 19 섹션을 참조하십시오.
전원 제어 절차 미리 보기 다음 표는 클러스터에서 관련 구성 요소를 전원 끄기 또는 설치하는 데 필요한 단계의 미리 보기입니다. 표 1. 전원 제어 절차 미리 보기 구성 요소 작업 PowerStore T 모델 PowerStore X 모델 노드 전원 끄기 PowerStore Manager를 사용합 니다. VMware vCenter Server 사용 또는 서비스 스크립트 실행. 전원 켜기 ● 노드가 섀시에서 분리된 경 ● 노드가 섀시에서 분리된 경 우 노드를 섀시에 다시 장착 우 노드를 섀시에 다시 장착 하고 전원 케이블을 다시 연 하고 전원 케이블을 다시 연 결합니다. 결하고 VMware vCenter Server를 사용합니다. ● 노드가 섀시에서 제거되지 않은 경우 서비스 스크립트 ● 노드가 섀시에서 분리되지 를 실행합니다. 않은 경우 서비스 스크립트 를 실행하고 VMware vCenter Server를 사용합니 다. 재시작 PowerStore Manager를 사용합 니다.
2 전원 제어 절차 이 장에서 다루는 내용은 다음과 같습니다. 주제: PowerStore 노드 전원 끄기 절차 PowerStore 노드 전원 켜기 절차 PowerStore 노드 재부팅 절차 PowerStore 어플라이언스 전원 끄기 절차 PowerStore 어플라이언스의 전원 켜기 절차 PowerStore 클러스터 전원 끄기 절차 PowerStore 클러스터 전원 켜기 절차 • • • • • • • PowerStore 노드 전원 끄기 절차 이 섹션에서는 다음 절차를 설명합니다. ● PowerStore Manager를 사용하여 PowerStore T 모델 노드 전원 끄기 페이지 7 ● 서비스 스크립트를 사용하여 PowerStore T 모델 노드의 전원 끄기 페이지 8 ● PowerStore X 모델 노드 전원 끄기 페이지 8 PowerStore Manager를 사용하여 PowerStore T 모델 노드 전원 끄기 전제조건 다음 정보를 수집합니다.
서비스 스크립트를 사용하여 PowerStore T 모델 노드의 전원 끄기 전제조건 다음 정보를 수집합니다. ● 노드가 포함된 어플라이언스의 관리 IP 주소입니다. PowerStore Manager에서 Settings > Networking > Networking IPs > Management로 이동합니다. Management IPs 표를 검토하여 어플라이언스와 연결된 관리 IP 주소를 식별합니다. ● 서비스 계정 자격 증명 노트: 피어 노드가 정상적으로 작동하지 않는 경우, 노드 전원을 끄거나 재부팅하지 마십시오. 피어 노드에 심각한 문제가 발생하 는 경우 관련 알림 및 이벤트는 PowerStore Manager에 표시됩니다. 또한 서비스 중단을 방지하려면 연결된 모든 호스트에서 피어 노드로의 경로가 충분하고 정상 작동해야 합니다. 이 작업 정보 다음 절차에 따라 서비스 스크립트를 사용하여 PowerStore T 모델 노드의 전원을 종료합니다. 단계 1.
VMware DRS는 사용자 VM을 피어 노드의 ESXi 호스트로 마이그레이션하기 시작하고 PowerStore 컨트롤러 VM의 전원을 끕니다. 5. 모든 관련 사용자 VM이 피어 노드의 ESXi 호스트로 마이그레이션되었는지 모니터링하고 확인합니다. 6. vCenter Server 콘솔을 모니터링하고 PowerStore X 모델 노드의 ESXi 호스트가 유지 관리 모드로 전환되었는지 확인합니다. 7. vCenter 명령을 사용하여 유지 보수 모드에 있는 ESXi 호스트를 종료합니다. 8. vCenter Server 콘솔을 모니터링하여 ESXi 호스트가 종료되었는지 확인합니다. 다음 단계 노드의 전원이 꺼졌는지 확인하려면 섀시 후면에 있는 LED의 상태를 확인합니다. 전원 공급 장치, 관리 포트 및 서비스 포트의 LED 외 에 노드의 다른 모든 LED가 꺼져 있어야 합니다. 활성 또는 피어 노드의 안전하지 않은 분리 LED가 나타납니다.
서비스 스크립트를 사용하여 PowerStore X 모델 노드 전원 켜기 전제조건 다음 정보를 수집합니다. ● 어플라이언스와 연결된 VMware vCenter Server의 주소 ● 연결된 vCenter Server 계정 자격 증명 ● 노드가 포함된 어플라이언스의 관리 IP 주소입니다. ● 서비스 계정 자격 증명 이 작업 정보 다음과 같은 시나리오에서 PowerStore X 모델 노드의 전원을 켜기 위해 다음 절차를 따릅니다. ● 원격으로 노드를 재장착할 수 없습니다. ● 노드가 섀시에서 분리되지 않았습니다. ● 내장형 모듈, I/O 모듈 및 4 포트 카드가 교체되었습니다. 단계 1. SSH 클라이언트를 실행하고 관리 IP 주소를 사용하여 어플라이언스에 접속합니다. 피어 노드는 전원이 켜져 있기 때문에 어플라 이언스의 피어 노드에 직접 연결됩니다. 2. 서비스 계정과 연결된 사용자 이름과 암호를 입력하고 로그인합니다. 3. 명령을 실행합니다.
● 서비스 스크립트를 사용하여 PowerStore T 모델 노드 재부팅 페이지 11 ● PowerStore X 모델 노드 재부팅 페이지 12 PowerStore Manager를 사용하여 PowerStore T 모델 노드를 재부팅합 니다. 전제조건 다음 정보를 수집합니다. ● PowerStore Manager에 로그인할 클러스터의 관리 IP 주소입니다. ● 관리자 권한이 있는 PowerStore Manager 사용자 계정 자격 증명 노트: 피어 노드가 정상적으로 작동하지 않는 경우, 노드 전원을 끄거나 재부팅하지 마십시오. 피어 노드에 심각한 문제가 발생하 는 경우 관련 알림 및 이벤트는 PowerStore Manager에 표시됩니다. 또한 서비스 중단을 방지하려면 연결된 모든 호스트에서 피어 노드로의 경로가 충분하고 정상 작동해야 합니다. 이 작업 정보 다음 절차에 따라 PowerStore Manager를 사용하여 PowerStore T 모델 노드의 재부팅을 수행합니다. 단계 1.
PowerStore X 모델 노드 재부팅 전제조건 다음 정보를 수집합니다. ● 어플라이언스와 연결된 VMware vCenter Server의 주소 ● 연결된 vCenter Server 계정 자격 증명 노트: 피어 노드가 정상적으로 작동하지 않는 경우, 노드 전원을 끄거나 재부팅하지 마십시오. 피어 노드에 심각한 문제가 발생하 는 경우 관련 알림 및 이벤트는 PowerStore Manager에 표시됩니다. 또한 서비스 중단을 방지하려면 연결된 모든 호스트에서 피어 노드로의 경로가 충분하고 정상 작동해야 합니다. 이 작업 정보 다음 절차에 따라 PowerStore X 모델 노드를 재부팅합니다. 단계 1. 연결된 vCenter Server에 로그인합니다. 2. 피어 노드의 ESXi 호스트로 자동 마이그레이션되도록 구성되지 않은 사용자 VM이 있는 경우 수동으로 마이그레이션합니다. 노트: vSPHERE Remote Office Branch Office Advanced는 자동 마이그레이션을 지원하지 않습니다.
클러스터에 포함된 모든 어플라이언스의 전원을 끄려면 PowerStore T 모델 클러스터 전원 끄기 페이지 15 섹션을 참조하십시오. 단계 1. PowerStore Manager에 로그인합니다. 2. Hardware에서 전원을 끄려는 어플라이언스를 선택합니다. 3. More Actions에서 Power Down을 선택합니다. Validation 창이 열립니다. 4. 오류, 경고 및 권장 사항을 검토합니다. 어플라이언스가 모든 유효성 검사를 통과하면 Next를 클릭합니다. Active Objects 창이 열립니다. 5. 지난 5분 동안 I/O 작업이 있는 어플라이언스의 객체 목록을 검토합니다. 6. 다음을 클릭합니다. Confirm 창이 열립니다. 7. 서비스 암호를 입력한 다음 Power Down을 클릭합니다. 8. 섀시 후면에 있는 LED의 상태를 확인하여 어플라이언스의 전원이 꺼져있는지 확인합니다.
6. 다음 명령을 실행하여 종료하는 어플라이언스가 기본 어플라이언스인지 확인합니다. svc_cluster_management GetClusterStatus 7. 종료하는 어플라이언스가 기본 어플라이언스인 경우 다음 명령을 실행하여 새 기본 어플라이언스로 사용할 어플라이언스를 지 정합니다. svc_cluster_management MoveMasterAppliance 8. PowerStore Manager의 Hardware에서 전원을 끄려는 어플라이언스를 선택합니다. 9. More Actions에서 Power Down을 선택합니다. Validation 창이 열립니다. 10. 오류, 경고 및 권장 사항을 검토합니다. 어플라이언스가 모든 유효성 검사를 통과하면 Next를 클릭합니다. Active Objects 창이 열립니다. 11. 지난 5분 동안 I/O 작업이 있는 어플라이언스의 객체 목록을 검토합니다. 12. 다음을 클릭합니다.
● 클러스터의 관리 IP 주소 및 서비스 계정 자격 증명 이 작업 정보 다음 절차를 사용하여 PowerStore X 모델 어플라이언스의 전원을 켭니다. 단계 1. 노드가 분리된 경우 베이스 인클로저 섀시에 다시 장착합니다. 2. 해당하는 경우 확장 인클로저도 캐비닛에 다시 장착되어 있어야 합니다. 3. 해당하는 경우 다음과 같이 오름차순에 따라 각 연결된 확장 인클로저에 전원 케이블을 다시 연결합니다. ● 확장 인클로저 0 ● 확장 인클로저 1 ● 확장 인클로저 2 전원 케이블이 연결되면 각 확장 인클로저의 전원 상태 LED가 켜집니다. 4. 먼저 노드 A에 전원 케이블을 다시 연결한 다음 노드 B를 연결합니다. 둘 중 하나의 노드에 전원 케이블이 연결되면 두 노드의 노드 전원 LED가 켜집니다. 유지 보수 모드에서 두 노드에 대한 ESXi 호스 트가 켜집니다. 5. 연결된 vCenter Server에 로그인하고 유지 보수 모드에서 노드 A에 대한 ESXi 호스트를 종료합니다.
이 작업 정보 다음 절차에 따라 PowerStore T 모델 클러스터 전원 끄기를 수행합니다. 단계 1. 다음 방법 중 하나를 사용하여 전원 끄기 명령을 실행합니다. ● PowerStore Manager를 사용하는 방법: a. Settings 아이콘을 선택한 뒤 Cluster 섹션에서 Power Down을 선택합니다. b. 확인 프롬프트가 표시되면 서비스 암호를 입력하고 Power Down을 클릭합니다. ● 서비스 스크립트를 사용하는 방법: a. SSH 클라이언트를 실행하고 관리 IP 주소를 사용하여 어플라이언스에 접속합니다. b. 서비스 계정과 연결된 사용자 이름과 암호를 입력하고 로그인합니다. c. 다음 명령을 실행하여 어플라이언스의 전원을 끕니다. svc_cluster shutdown 2. 노드 전원 LED를 확인하여 프로세스의 상태를 확인합니다. 클러스터의 모든 노드에 대한 노드 전원 LED가 꺼지면 전원 끄기 프로 세스가 완료됩니다. 3.
3. PowerStore X 모델 컨트롤러 VM을 제외한 모든 사용자 VM을 종료합니다. 4. iSCSI 또는 FC를 사용하여 PowerStore X 모델 클러스터 스토리지에 액세스하는 외부 컴퓨팅 서버가 환경에 있는 경우 해당 VM을 종료합니다. 5. vSphere에서 보조 ESXi 호스트를 유지 보수 모드로 전환합니다. 6. 컨트롤러 VM의 전원이 꺼질 때까지 기다립니다. 5분 후에 컨트롤러 VM의 전원이 꺼지지 않으면 vSphere에서 VM의 전원을 수동 으로 끕니다. PowerStore X 모델 컨트롤러의 전원이 꺼지면 ESXi가 유지 보수 모드로 전환됩니다. 7. 기본 ESXi 호스트를 유지 관리 모드로 전환합니다. 8. 컨트롤러 VM의 전원이 꺼질 때까지 기다립니다. 5분 후에 컨트롤러 VM의 전원이 꺼지지 않으면 vSphere에서 VM의 전원을 수동 으로 끕니다. PowerStore X 모델 컨트롤러의 전원이 꺼지면 ESXi가 유지 보수 모드로 전환됩니다. 9.
표 3. 컨트롤러 VM 전원 켜기 클러스터 크기 어플라이언스 1 어플라이언스 2 어플라이언스 3 어플라이언스 4 컨트롤러 VM A 컨트롤러 VM B 컨트롤러 VM A 컨트롤러 VM B 컨트롤러 VM A 컨트롤러 VM B 컨트롤러 VM A 컨트롤러 VM B 1 1 수동 전원 켜기 2 자동 전원 켜기 2 1 수동 전원 켜기 2 수동 전원 켜기 3 수동 전원 켜기 4 자동 전원 켜기 3 1 수동 전원 켜기 2 수동 전원 켜기 3 수동 전원 켜기 4 자동 전원 켜기 5 자동 전원 켜기 6 자동 전원 켜기 4 1 수동 전원 켜기 2 수동 전원 켜기 3 수동 전원 켜기 4 수동 전원 켜기 5 수동 전원 켜기 6 자동 전원 켜기 7 자동 전원 켜기 8 자동 전원 켜기 단계 1. 노드가 분리된 경우 베이스 인클로저 섀시에 다시 장착합니다. 2. 해당하는 경우 확장 인클로저도 캐비닛에 다시 장착되어 있어야 합니다. 3.
A 교체 가능 유닛 취급 시 안전 예방 조치 시스템의 손상을 방지하려면 어느 부품이든 교체하기 전에 아래의 안전 고려 사항을 검토하십시오. 주제: • 교체 가능 유닛 취급 교체 가능 유닛 취급 이 섹션에서는 교체 가능 유닛을 분리, 설치 및 보관할 때 따라야 하는 사전 주의 사항과 일반 절차에 대해 설명합니다. ESD(Electrostatic Discharge) 피해 방지 하드웨어 유닛을 교체하거나 설치할 때 장비의 민감한 전자 회로를 실수로 만지면 부품이 손상될 수 있습니다. 회로를 만지면 인체에 누적된 정전기가 방전됩니다. 작업 구역의 공기가 매우 건조한 경우 습도 조절 장치를 사용하면 ESD 손상 위험 을 줄일 수 있습니다. 장비 손상을 방지하려면 다음 절차를 따르십시오. ● ● ● ● ● ● 장비 사용을 위한 충분한 공간을 확보하십시오. 설치 장소에서 발포 포장, 발포 컵, 셀로판 포장지 등 자연적으로 정전기를 발생시키는 불필요한 재료를 치우십시오.
운반/보관 환경 운영 환경 온도 적응 시간 0시간~1시간 온도 습도 정격 정격 정격 20°C~22°C(68°F~72°F) 68°F - 72°F(20°C 22°C) 40% - 55% RH 40% - 55% RH 콜드 건조 <30°C(86°F) 4시간 <68°F(20°C) <30% RH 콜드 다습 <30°C(86°F) 4시간 <68°F(20°C) ≥30% RH 핫 건조 <30°C(86°F) 4시간 >72°F(22°C) <30% RH 핫 고습 30%~45% RH <30°C(86°F) 4시간 고습 45%~60% RH <30°C(86°F) 8시간 고습 ≥60% RH <30°C(86°F) 16시간 <30°C(86°F) 16시간 >72°F(22°C) 알 수 없음 ● 권장 적응 시간이 지난 후에도 응축이 생길 것 같으면 추가로 8시간 동안 두고 안정화합니다.
부품 포장 풀기 다음의 모범 사례를 사용하여 부품의 포장을 푸십시오. 단계 1. ESD 장갑을 착용하거나 부품을 설치할 엔클로저에 ESD 밴드를 연결하고 손목에 착용합니다. 2. 부품의 포장을 풀고 정전기가 없는 표면에 놓습니다. 3. 장애가 발생한 부품의 교체에 사용되는 부품인 경우 장애가 발생한 부품을 반환할 때 사용하도록 포장재를 보관합니다.
B 지원 알림 지원 알림을 비활성화하고 활성화하는 방법에 대해 알아보십시오. 주제: • • 지원 알림 해제 지원 알림 활성화 지원 알림 해제 불필요하게 운영 중단에 대해 고객 지원에 알리지 않으려면 전원을 끄거나 재부팅하여 노드 연결을 해제하는 절차를 시작하기 전에 지원 알림을 비활성화하십시오. 단계 1. PowerStore Manager에서 Settings > Support > Disable Support Notifications로 이동합니다. 2. 서비스하는 어플라이언스의 확인란을 클릭합니다. 3. Modify를 클릭합니다. 4. Enable Maintenance Mode 확인란을 클릭합니다. 5. Maintenance Window Duration (in hours) 필드에 절차 시간보다 긴 시간을 입력합니다. 6. Apply를 클릭합니다.