Dell EMC PowerStore PowerStore T 모델을 위한 네트워킹 가이드 버전 2.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2020 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자 의 상표일 수 있습니다.
목차 추가 리소스.....................................................................................................................................6 장 1: 개요........................................................................................................................................ 7 PowerStore T 모델 어플라이언스 개요............................................................................................................................ 7 PowerStore T 모델 초기 배포 및 스토리지 네트워크 구성..................................
부분 II: 스토리지 서비스 추가........................................................................................................... 36 장 8: 스토리지 서비스 개요.......................................................................................................... 37 스토리지 서비스........................................................................................................................................................... 37 장 9: 스토리지 서비스에 대한 스위치 및 네트워크 구성 준비........................................................
노드를 ToR 스위치에 케이블로 연결.........................................................................................................................71 ToR 스위치에서 VLAN 구성........................................................................................................................................72 IP 주소 추가 및 스토리지 네트워크 매핑................................................................................................................. 73 부록 B: 추가 스토리지 네트워크 생성...................................................
서문 제품군을 향상시키기 위한 노력의 일환으로 소프트웨어와 하드웨어의 개정 버전을 정기적으로 릴리스하고 있습니다. 이 문서에서 설 명하는 일부 기능은 현재 사용 중인 소프트웨어 또는 하드웨어의 일부 버전에서 지원되지 않을 수 있습니다. 제품 릴리스 노트에는 제 품 기능에 대한 최신 정보가 제공되어 있습니다. 제품이 올바르게 작동하지 않거나 이 문서에 설명된 대로 작동하지 않는 경우 서비스 공급업체에 문의하십시오. 지원 정보 지원, 제품 및 라이선스 정보는 다음과 같이 확인할 수 있습니다. ● 제품 정보 제품 및 기능 설명서 또는 릴리스 노트를 보려면 https://www.dell.com/powerstoredocs에서 PowerStore 설명서 페이지를 참조 바 랍니다. ● 문제 해결 제품, 소프트웨어 업데이트, 라이선스 등록 및 서비스에 대한 자세한 내용은 https://www.dell.com/support에서 해당 제품 지원 페 이지를 참조 바랍니다.
1 개요 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: PowerStore T 모델 어플라이언스 개요 PowerStore T 모델 초기 배포 및 스토리지 네트워크 구성 지원되는 스위치 • • • PowerStore T 모델 어플라이언스 개요 소프트웨어 스택이 시스템 베어 메탈에 직접 배포되는 블록(SAN(storage area networks)), 파일(NAS(network attached storage)), 가 상 볼륨(vVol) 워크로드를 지원합니다. PowerStore T 모델 모델 번호: ● ● ● ● ● ● 500T 1000T 3000T 5000T 7000T 9000T 노트: 이 모델에서는 하이퍼바이저 배포가 지원되지 않습니다. 하이퍼바이저 배포는 PowerStore X 모델 어플라이언스에서 지원 됩니다. 지원 설명서 스위치와 네트워크를 구성하기 전에, 이 문서를 읽는 것 외에도 다음 가이드를 참조 바랍니다.
표 1. PowerStore T 모델 배포 옵션 (계속) 배포 옵션 프로토콜 및 서비스 스위치 요구 사항 참조 유니파이드 배포를 통해 스 토리지 서비스에는 NAS(Network Attached Storage)에 대한 지원이 포 함될 수 있습니다. 지원되는 스위치 PowerStore는 OS10EE(OS10 Enterprise Edition)를 실행하는 다음과 같은 Dell EMC PowerSwitch 이더넷 스위치와 함께 구매할 수 있습 니다. ● S4148F-ON ● S4148T-ON ● S5248F-ON 이 가이드의 계획 및 요구 사항 섹션을 참조하면 지원되는 스위치를 사용하여 PowerStore 어플라이언스 배포를 준비할 수 있습니다. 그러나 이 가이드에 제공된 구성 단계는 Dell EMC PowerSwitch Series S4148-ON 스위치를 사용하여 PowerStore를 배포하는 특정 단 계입니다.
I 초기 배포 이 부분에는 PowerStore T 모델의 초기 배포를 완료하는 데 필요한 정보가 포함되어 있습니다.
2 PowerStore T 모델의 초기 배포 개요 주제: • PowerStore T 모델의 초기 배포 PowerStore T 모델의 초기 배포 PowerStore T 모델를 처음 배포하려면 관리 스위치와 네트워크를 구성해야 합니다. 관리 스위치를 구성하고 PowerStore T 모델 노드에 연결한 후에는 PowerStore Manager Initial Configuration Wizard에서 PowerStore T 모델 어플라이언스를 검색하고 네트워크를 구성합니다. 초기 배포를 완료한 후에 PowerStore T 모델는 Fibre Channel 연결을 지원하도록 구성됩니다. iSCSI 호스트 접속 구성, 복제, 가져오기, 클러스터링 또는 NAS(Network Attached Storage)와 같은 서비스를 지원하려면 2부: 스토리 지 서비스 추가에 설명된 대로 추가 구성 단계를 수행해야 합니다.
3 관리 스위치 및 네트워크 구성 준비 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: 초기 배포를 위한 네트워크 리소스 예약 초기 구성 워크시트에서 필수 필드 입력 • • 초기 배포를 위한 네트워크 리소스 예약 PowerStore T 모델 어플라이언스의 초기 배포에 필요한 리소스를 예약하려면 네트워크 관리자와 협력하여 다음 2개의 워크시트를 작성합니다. PowerStore T 모델 어플라이언스를 배포하는 데 사용할 요구 사항 및 네트워크 리소스에 대한 자세한 내용은 초기 배포를 위한 스위 치 및 네트워크 요구 사항을 참조하십시오. 초기 배포 후 추가 프로토콜과 서비스에 대한 ToR(Top-of-Rack) 스위치를 구성하는 경우에는 ToR 스위치를 지금 구성하는 데 필요한 리소스를 예약할 수도 있습니다. 스토리지 네트워크 준비 워크시트를 참조하십시오.
표 3. 관리 네트워크 준비 워크시트 (계속) 단계 단계 세부 정보 참고 ● 스위치의 네트워크 구성이 PowerStore T 모델에서 수행한 네트워크 구성과 일치합니다. ● PowerStore T 모델 및 PowerStore T 모델 네트워크의 초기 구성을 완료하기 위해 필요한 네트워크 리소스를 예약합니 다. 10. PowerStore 검색에 직접 연결을 사용할지 원격 연결을 사용할지 결정합니다. PowerStore를 성공적으로 검색한 후, Initial Configuration Wizard를 통해 첫 번째 PowerStore 클러스터를 생성합니다. Dell EMC PowerSwitch Series에 대해 작성된 관리 네트워크 준비 워크시트의 샘플을 보려면 작성된 관리 네트워크 준비 워크시트 예 시를 참조하십시오.
표 4. 초기 구성 워크시트(비어 있음) (계속) ● 단일 드라이브 내결함성의 경우 최소 6개 ● 이중 드라이브 내결함성의 경우 7개 노트: 한 번 설정된 어플라이언스의 드라이브 내결함 성 수준은 변경할 수 없습니다. 관리 네트워크 클러스터에는 클러스터 및 관리 네트워크에 대한 전용 IP 주소 세트가 필요합니다. 관리 네트워크는 DNS 및 NTP와 같은 서비스에 클러스터를 연결합니다. 관리 네트워크의 IP 주소는 클러스터, 어플라이언스, 컨트 롤러 및 내부 호스트를 처리하는 데 사용됩니다. 노트: 관리 네트워크에 대 한 VLAN 정보는 선택 사항이며 기본값은 0입니다. 네트워크 트래픽에 태그가 지정되지 않고, 스위치 를 이용하여 기본 VLAN이 적용됨을 나타내는 데 사용되는 마커입니다. 보안 및 성능 향상을 위해 각 네트워크 유형에 대해 고유 한 VLAN 정보를 지정하는 것이 좋습니다. 클러스터 IP 주소 (각 PowerStore 클러스터마다 IP 주소 1개) 클러스터를 관리하는 데 사용되는 주소입니다.
표 4. 초기 구성 워크시트(비어 있음) (계속) 암호 처음에 PowerStore T 모델 어플라이언스에 로그인 한 후에 제공되는 사용자 정의 암호입니다. Dell PowerSwitch Series에 대해 작성된 초기 구성 워크시트의 샘플을 보려면 작성된 초기 구성 워크시트 가져오기를 참조하십시오. PowerStore T 모델 어플라이언스에 Fibre Channel 연결 외에 서비스를 추가할 계획인 경우 스토리지 네트워크 IP 주소를 지금 예약할 수 있지만 이는 선택 사항입니다. PowerStore T 모델의 초기 구성을 완료한 후에 스토리지 네트워크를 추가합니다. 자세한 내용은 스 토리지 서비스 추가를 참조하십시오.
4 초기 배포를 위한 스위치 및 네트워크 요구 사항 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • • • 관리 스위치 요구 사항 초기 배포에 필요한 네트워크 유형 초기 배포 시 VLAN 옵션 초기 배포를 위한 IP 요구 사항 관리 스위치 요구 사항 모든 PowerStore T 모델 배포에는 하나 이상의 아웃오브밴드 관리 스위치를 사용한 배포가 필요합니다. 노드-관리 스위치 관리 스위치는 다음 다이어그램에 설명된 대로 각 어플라이언스 베이스 인클로저 노드의 1GbE 관리 포트를 통해 연결됩니다. PowerStore T Management Switch Network Topology Management Switch Port Channel Port 0 Port 1 Port 1 Port 0 Node A Node B Mgmt Mgmt PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 1 .
다음 다이어그램은 PowerStore T 모델 베이스 인클로저 노드에서 관리 포트가 있는 위치를 보여줍니다. Node A Management Port Node B Management Port 그림 2 . PowerStore T 모델 베이스 인클로저 노드 관리 포트 관리 스위치 업링크 연결 다음 그림은 2개의 계층 3 업링크 디바이스에 연결하는 관리 스위치에 대한 예시를 보여줍니다. 두 연결은 모두 향상된 대역폭과 이 중화를 제공하는 포트 채널과 연결되어 있습니다.
PowerStore T Management Switch Network Topology with Upstream Switches Management Upstream Switch1 Management Upstream Switch2 Management Switch Port Channel Port 0 Port 1 Port 1 Port 0 Node A Node B Mgmt Mgmt PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 3 . 업링크 연결을 사용하는 관리 스위치 네트워크 토폴로지 초기 배포에 필요한 네트워크 유형 PowerStore T 모델의 모든 네트워크가 고유해야 합니다. 트래픽을 분리하기 위해 여러 개의 고유한 VLAN으로 PowerStore T 모델를 배포하는 것이 좋습니다. 하지만 VLAN 하나만 사용할 수 있는 경우에는 다음과 같이 단일 VLAN와 여러 개의 고유 서브넷으로 PowerStore T 모델를 배포할 수 있습니다.
PowerStore T Logical Networks Management Upstream Management switch PowerStore T Management Subnets Management Remote Discovery 그림 4 . PowerStore T 모델 논리적 네트워크 트래픽 모든 트래픽은 베이스 인클로저 노드의 전용 1GbE 관리 포트를 통해 전송됩니다. PowerStore T 모델에서 위에 표시된 서브넷을 통해 통신할 수 있는지 확인합니다. 네트워크 공급 업체의 문서를 참조하시어 PowerStore T 모델에서 사용 중인 모든 네트워크에 알맞은 L2 및/또는 L3 트래픽이 모두 올바르게 라우팅되고 있는지 확인합니다. 표 5.
PowerStore T – Untagged Management VLAN Management Management switch PowerStore T Sample ID 100 100 Traffic Remote Discovery PowerStore Management Untagged Traffic Tagged Traffic Subnet 169.254.x.x/16 y.y.y.y/24 그림 5 . 관리 VLAN 태그가 지정되지 않은 PowerStore T 모델 네트워크 관리 VLAN 태그가 지정되지 않은 경우 PowerStore T 모델의 원격 검색 및 관리는 기본 VLAN를 통해 실행됩니다.
PowerStore T – Tagged Management VLAN Management Upstream Management switch PowerStore T Sample ID 100 101 Traffic PowerStore Management Remote Discovery Untagged Traffic Tagged Traffic Subnet y.y.y.y/24 169.254.x.x/16 그림 6 . 관리 VLAN 태그가 지정된 PowerStore T 모델 네트워크 관리 VLAN 태그가 지정된 경우 PowerStore T 모델의 원격 검색은 기본 VLAN를 통해 실행되며, 관리 트래픽은 태그가 지정된 VLAN를 통해 실행됩니다. 노트: 이 문서에서는 태그가 지정되지 않은 VLAN으로 관리 네트워크를 구성하는 예시를 제공합니다.
스토리지 네트워크 초기 배포 시 스토리지 네트워크에 대한 IP 요구 사항은 없습니다. 그러나 나중에 PowerStore Manager, REST API, CLI를 추가하는 경 우에는 스토리지 네트워크에 대한 IP 주소가 필요합니다. 스토리지 서비스 추가를 참조하십시오.
5 초기 배포를 위한 Dell PowerSwitch Series 구성 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: Dell EMC PowerSwitch Series S4148 스위치를 사용한 구성 개요 PowerStore T 모델 캐비닛 안에 관리 스위치 설치 작성된 관리 네트워크 준비 워크시트 가져오기 초기 배포를 위해 관리 스위치를 구성하는 단계 관리 스위치의 구성 검증 PowerStore용 네트워크 유효성 검사 도구 • • • • • • Dell EMC PowerSwitch Series S4148 스위치를 사용한 구 성 개요 이 섹션에서는 Dell PowerSwitch Series S4148 관리 스위치에 연결된 단일 베이스 인클로저가 있는 어플라이언스 1개로 구성된 단일 클러스터를 사용하여 PowerStore T 모델를 배포하는 단계에 대해 설명합니다.
표 7. 관리 네트워크 준비 워크시트(작성 완료) 단계 단계 세부 정보 참고 1. 이 표를 인쇄하여 예약된 리소스를 기록합니다. 2. 초기 구성 워크시트를 인쇄하여 클러스터를 처음 생성할 때 PowerStore T 모델에서 네트워크를 생성하는 데 필요한 추가 네 트워크 리소스를 기록합니다. 3. 다음에 연결할 관리 스위치 포트를 기록합니다. 노드 A 관리 1GbE 포트 -> 관리 스위치 포트 2 노드 B 관리 1GbE 포트 -> 관리 스위치 포트 53 4. 필요에 따라 원격 검색에 사용할 관리 스위치의 포트를 기 록합니다. 관리 스위치 포트 1 5. 업링크에 연결하는 데 사용되는 관리 스위치의 포트를 기록합니다. 6. 7. 관리 업링크 A -> 관리 스위치 포트 25 관리 업링크 B -> 관리 스위치 포트 26 관리 스위치에서 사용할 VLAN ID를 기록합니다.
이 단계는 Dell EMC PowerSwitch S4148-ON 스위치 연결을 수립합니다. 콘솔 직렬 포트 케이블 요구 사항에 대한 자세한 내용은 https://www.dell.com/support/home/us/en/04/product-support/product/ networking-s4148f-on/docs에 있는 Dell EMC PowerSwitch S4100-ON Series 설치 가이드를 참조 바랍니다. 배포를 위해 스위치를 구성하려면 각 스위치에 터미널 세션을 수립해야 합니다. 1. 스위치의 전원을 켭니다. 2. 직렬 케이블을 사용하여 컴퓨터를 직렬 콘솔 포트에 연결합니다. 이 포트는 PowerSwitch의 PSU 사이드에 있는 최상위 포트입니 다. Serial Console Port Management Port 3. 컴퓨터에서 예를 들어 PuTTY와 같은 터미널 에뮬레이터 프로그램을 엽니다. 4. 다음 연결을 사용하여 터미널 에뮬레이터 프로그램에서 직렬 연결을 구성합니다. 표 8.
Build Time: 2018-09-26T17:20:01-0700 System Type: S4148F-ON Architecture: x86_64 Up Time: 2 weeks 04:34:35 3. 스위치에 라이센스가 설치되어 있는지 확인합니다. show license status 명령을 실행하여 라이센스 설치 여부를 표시합니다. License Type: 필드에 PERPETUAL이 표시되 어야 합니다. 평가판 라이센스가 설치된 경우 Dell EMC에서 구입한 라이센스를 Dell Digital Locker(www.dell.com/support/ software/)에서 다운로드할 수 있습니다.
no shutdown exit 6. 스위치의 관리 IP 주소를 구성합니다. 노트: 다음 명령 샘플에서는 DHCP(Dynamic Host Configuration Protocol)를 통한 자동 IP 할당이 스위치에서 활성화된 것으로 가정합니다. DHCP를 통한 자동 IP 할당이 활성화되어 있지 않은 경우 아래 명령에 no ip address dhcp를 포함할 필요가 없습니다. interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.50/24 exit 7. 스위치의 관리 경로(기본값 게이트웨이)를 구성합니다. management route 0.0.0.0/0 100.0.100.1 exit 8. 스위치의 NTP 서버를 구성합니다. ntp server 100.0.100.200 exit 9. PowerStore T 모델 관리 포트에 연결되는 스위치에 이더넷 포트를 구성합니다.
표 9. 관리 스위치 구성 시 코드 샘플 flowcontrol receive off flowcontrol transmit off exit 관리 스위치 케이블 연결 관리 스위치를 어플라이언스 베이스 인클로저 노드와 관리 업링크에 케이블로 연결합니다. 이 가이드의 예시에서는 Dell EMC PowerSwitch S4148 ON 스위치를 사용하여 PowerStore T 모델 어플라이언스를 배포하는 방법을 보여줍니다. 노드의 관리 포트를 관리 스위치에 케이블로 연결 관리 스위치는 각 어플라이언스 베이스 인클로저 노드의 1GbE 관리 포트를 통해 연결됩니다. 2 1 그림 7 . 관리 스위치에 베이스 인클로저 어플라이언스 연결 표 10. 베이스 인클로저 노드를 관리 스위치에 연결하는 단계 1 하단 노드(A)의 관리 1GbE 포트를 관리 스위치의 포트 2에 연결합니다. 2 상단 노드(B)의 관리 1GbE 포트를 관리 스위치의 포트 53에 연결합니다.
Layer 3 – Management Uplinks Management Uplink A Management Uplink B 2 1 그림 8 . 관리 스위치를 관리 업링크에 연결 표 11. 관리 스위치를 관리 업링크에 연결하는 단계 1 관리 스위치 포트 25를 관리 업링크 A에 연결합니다. 2 관리 스위치 포트 26을 관리 업링크 B에 연결합니다. 노트: 네트워크 관리자와 상의하여 관리 스위치가 연결될 업링크 포트를 결정합니다. 관리 스위치의 구성 검증 관리 스위치를 구성하고 스위치를 PowerStore T 모델 노드에 케이블로 연결한 후 PowerStore T 모델 검색 전에 스위치 구성을 검증합 니다. 1. 스위치에 터미널 세션을 수립합니다. 2. 인터페이스 상태를 검증합니다.
3. 포트 채널 구성을 검증합니다. show port-channel summary Flags: D - Down I - member up but inactive P - member up and active U - Up (port-channel) F - Fallback Activated -------------------------------------------------------------------------------Group Port-Channel Type Protocol Member Ports -------------------------------------------------------------------------------10 port-channel10 (U) Eth DYNAMIC 1/1/25(P) 1/1/26(P) 4. 네트워크 구성을 검증합니다.
6 PowerStore 어플라이언스 검색 이 부록에서 다루는 내용은 다음과 같습니다. 주제: • • 직접 연결을 사용하는 검색 원격 연결을 사용하는 검색 직접 연결을 사용하는 검색 이 권장 절차는 베이스 인클로저가 설치된 위치에서만 수행 가능합니다. ● (선택 사항) PowerStore 네트워크 유효성 검사 도구(NVT)를 다운로드하고 실행하여 네트워크가 올바르게 구성되어 있는지 검증 합니다. NVT는 Dell EMC Central Solutions(https://psapps.emc.com/central/solutions)에서 다운로드할 수 있습니다. ● 워크스테이션의 네트워크 어댑터가 다음과 같이 구성되어 있는지 확인합니다. ○ 노드 A의 PowerStore 서비스 포트에 직접 연결됩니다. ○ 게이트웨이 주소(128.221.1.249; 255.255.255.0; no gateway)가 정의되지 않은 서비스 LAN 포트(128.221.1.0/24)에 정적 IP 주소 를 구성합니다.
Node Network B A 그림 9 . PowerStore T 모델 원격 검색 연결 다음과 같은 두 가지 검색 방법을 선택할 수 있습니다. ● 검색 툴을 사용하는 원격 검색 ● 정적 IP 주소를 사용하는 원격 검색 검색 툴을 사용하는 원격 검색 169.254.xx/16 IP 주소를 알리는 검색 툴을 사용하여 PowerStore를 검색할 수 있습니다. ● (선택 사항) PowerStore에 대한 네트워크 유효성 검사 도구(NVT)를 다운로드하고 실행하여 네트워크가 올바르게 구성되어 있는 지 확인합니다. NVT는 Dell EMC Central Solutions(https://psapps.emc.com/central/solution/NVT-PowerStore)에서 다운로드할 수 있습니다. ● 일시적으로 방화벽을 비활성화합니다. 이렇게 할 수 없는 경우 포트 5353 및 검색 유틸리티를 워크스테이션에서 실행되는 모든 방화벽 및 안티바이러스 소프트웨어의 제외 목록에 추가합니다.
지 않은 169.254.1.2로 설정합니다. 이 주소는 DHCP 또는 정적 IP 주소의 사용 여부와 상관없이 다른 주소 범위에서 덮어쓸 수 없습니다. 노트: 중복 IP 주소가 발생하지 않도록 하려면 설정하는 169.254.x.x IP 주소를 사용하는 동일한 기본/태그 미지정 네트워 크에 하나의 노트북 또는 가상 머신만 있어야 합니다. 1. 워크스테이션 또는 가상 머신에서 웹 브라우저를 열고 PowerStore 검색 유틸리티에 액세스하기 위해 예약된 IP 주소 중 하나를 입 력합니다. ● http://169.254.0.10 ● http://169.254.0.20 ● http://169.254.0.30 ● http://169.254.0.40 ● http://169.254.0.50 2. PowerStore Manager에 로그인하고 다음과 같은 기본 자격 증명을 사용하여 초기 구성 프로세스를 시작합니다.
7 PowerStore T 모델 어플라이언스의 초기 구성 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • 초기 구성 마법사 작성된 초기 구성 워크시트 가져오기 초기 구성 마법사 PowerStore T 모델 어플라이언스를 검색한 후에는 Initial Configuration Wizard(ICW)로 리디렉션되어 PowerStore T 모델 어플라이 언스에 네트워크를 구성합니다. Initial Configuration Wizard(ICW)에는 PowerStore T 모델 어플라이언스의 초기 구성에 필요한 네트워크 정보를 입력하라는 메시지 가 표시됩니다. ICW를 통해 실행하는 동안에는 작성된 초기 구성 워크시트를 참조하십시오. 초기 구성 워크시트는 PowerStore T 모델 어플라이언스 의 초기 배포를 완료하는 데 필요한 모든 정보로 작성해야 합니다. ICW를 통해 실행하는 동안 다음 사항에 유의하십시오.
작성된 초기 구성 워크시트 가져오기 네트워크 관리자와 협력하여 초기 구성 워크시트를 작성해야 합니다. 다음 워크시트는 Dell EMC PowerSwitch Series S4148-ON ToR(Top-of-Rack) 스위치에 구성된 리소스를 사용하여 작성되었습니다. 대 체 네트워크 리소스를 사용하여 환경을 구성하는 경우 초기 구성 워크시트(비어 있음)에서 이 가이드에 나와 있는 빈 워크시트를 작 성합니다. 또한 아래의 작성된 초기 구성 워크시트에서 클러스터에 대해 정의하는 관리자 암호를 기록해 두십시오. 사용자 정의 암호 샘플은 제 공되지 않습니다. 표 12. 초기 구성 워크시트(작성 완료) 초기 로그인 정보 PowerStore Manager에 처음으로 로그인 할 때 다음의 기본 사용자 자격 증명을 사용합니다. PowerStore Manager 클러스터의 초기 구성을 완료하려면 새 관리자 암호를 입력해야 합니다.
표 12. 초기 구성 워크시트(작성 완료) (계속) 노트: 관리 네트워크에 대 한 VLAN 정보는 선택 사항이며 기본값은 0입니다. 네트워크 트래픽에 태그가 지정되지 않고, 스위치 를 이용하여 기본 VLAN이 적용됨을 나타내는 데 사용되는 마커입니다. 보안 및 성능 향상을 위해 각 네트워크 유형에 대해 고유 한 VLAN 정보를 지정하는 것이 좋습니다. 클러스터 IP 주소 192.168.1.10 (각 PowerStore 클러스터마다 IP 주소 1개) 클러스터를 관리하는 데 사용되는 주소입니다. VLAN(선택 사항, 기본값은 0) 넷마스크/접두사 길이 게이트웨이 IP 주소 각 PowerStore T 모델 어플라이 언스마다 IP 3개 255.255.255.0/24 0 192.168.1.1 192.168.1.11-13 인프라스트럭처 서비스 DNS 및 NTP 서버의 IP 주소를 기록합니다. DNS 및 NTP 서버에 최소 2개의 주소를 각각 지정하는 것이 좋습니다. DNS 서버 100.0.
II 스토리지 서비스 추가 이 부분에는 스위치를 준비하고 PowerStore T 모델용 Dell EMC PowerSwitch Series를 추가 프로토콜 및 서비스로 구성하기 위한 정보 가 포함되어 있습니다.
8 스토리지 서비스 개요 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • 스토리지 서비스 스토리지 서비스 PowerStore T 모델 어플라이언스는 초기 배포 후 Fibre Channel에 대해 구성됩니다. 초기 배포 후 스토리지 서비스를 추가할 수 있는 옵션이 있습니다. 스토리지 서비스에는 다음과 같은 프로토콜 및 서비스가 포함됩니다. ● ● ● ● ● iSCSI 호스트 접속 구성 복제 가져오기 클러스터링 NAS(Network Attached Storage) 노트: NAS는 유니파이드 배포에만 포함되어 있습니다. 스토리지 서비스 추가를 위한 스위치 요구 사항 스토리지 서비스를 추가하려면 PowerStore T 모델 어플라이언스를 2개의 ToR(Top-of-Rack) 스위치에 연결해야 합니다.
9 스토리지 서비스에 대한 스위치 및 네트워크 구성 준비 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: 스토리지 서비스용 스위치 리소스 워크시트 스토리지 네트워크 구성 워크시트 • • 스토리지 서비스용 스위치 리소스 워크시트 네트워크 관리자와 협력하여 스토리지 서비스용 스위치 리소스 워크시트를 작성하고 스토리지 서비스에 필요한 2개의 ToR(Top-ofRack) 스위치를 구성하는 데 필요한 리소스를 예약합니다. Dell PowerSwitch Series에 대해 작성된 스토리지 서비스용 스위치 리소스 워크시트 샘플은 스토리지 서비스용 스위치 리소스 워크시 트 작성 예시를 참조하십시오. 노트: 이 섹션에서는 초기 배포를 완료했고 관리 스위치와 네트워크가 성공적으로 구성된 것으로 가정합니다. 또한 PowerStore Manager에서 스토리지 네트워크를 생성하는 데 필요한 리소스를 예약하려면 네트워크 관리자와 협력하여 스토리 지 네트워크 구성 워크시트를 작성하는 것이 좋습니다. 표 13.
표 13. 스토리지 서비스용 스위치 리소스(비어 있음) (계속) 단계 단계 세부 정보 참고 ToR 스위치 2의 관리 IP 주소 기본 게이트웨이 NTP 서버 5. Dell EMC는 계층 2 상호 연결 링크를 사용하는 2개의 ToR(Top-of-Rack) 스위치를 사용하는 PowerStore T 모델 배포를 지원 합니다. 사용할 계층 2 상호 연결 유형을 선택합니다. 매우 권장됨: MC-LAG(Multi-chassis Link Aggregation Group) MC-LAG를 사용하는 경우 스위치를 함께 연결하는 데 사용할 포트를 기록합니다. ToR 스위치 1에서 ToR 스위치 2 포트 페어 1로 전환 ToR 스위치 1에서 ToR 스위치 2 포트 페어 2로 전환 또는 MC-LAG가 없는 L2 업링크 6. MC-LAG를 사용하는 경우 도메인 ID를 입력합니다. 7. 계층 2 상호 연결에 MC-LAG(VLT)를 사용하는 경우 다음을 기록합니다.
표 13. 스토리지 서비스용 스위치 리소스(비어 있음) (계속) 단계 단계 세부 정보 참고 ToR 스위치 2용 스패닝 트리 프로토콜 스토리지 네트워크 구성 워크시트 PowerStore Manager에서 스토리지 네트워크를 생성하려면 다음 리소스를 예약해야 합니다. 네트워크 관리자와 협력하여 PowerStore Manager에서 생성하는 각 스토리지 네트워크에 대한 아래 스토리지 네트워크 구성 워크시 트를 작성합니다. 표 14. 스토리지 네트워크 구성 워크시트(비어 있음) 리소스 참고 스토리지 네트워크 이름 VLAN ID 스토리지 네트워크에 대한 VLAN 정보는 선택 사항이며 기본값은 0입니다. 네트워크 트래픽에 태그가 지정되지 않고, 스위치를 이용하여 기본 VLAN이 적용됨을 나타내는 데 사용되는 마커입니다. 보안 및 성능 향상을 위해 각 네트워크 유형에 대해 고유한 VLAN ID를 지정하는 것이 좋습니다.
10 ToR 스위치를 사용한 배포를 위한 스위치 및 네트 워크 요구 사항 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • • • ToR(Top-of-Rack) 스위치 연결 구성 옵션 및 요구 사항 스토리지 서비스를 추가할 때의 네트워크 구성 스토리지 네트워크 및 NAS 서버를 추가하는 경우의 VLAN 옵션 스토리지 서비스 추가를 위한 스토리지 네트워크 IP 주소 요구 사항 ToR(Top-of-Rack) 스위치 연결 구성 옵션 및 요구 사항 PowerStore T 모델 어플라이언스를 처음 배포할 때 구성된 관리 스위치 외에도 두 개의 ToR 스위치를 추가해야 iSCSI 연결, 복제, 가 져오기, 클러스터 및 NAS(Network Attached Storage)를 지원할 수 있습니다. ToR(Top-of-Rack) 스위치와 ToR 스위치(L2) 연결 옵션 다음 옵션 중 하나를 사용하여 두 ToR 스위치를 함께 연결합니다. 표 15.
PowerStore Network Topology with Top of Rack Switches and MC-LAG Interconnect Upstream Switch 2 Upstream Switch 1 Port Channel Top of Rack Switch 1 Port 0 MC-LAG Interconnect Port 1 Top of Rack Switch 2 Port 1 Node A Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 10 .
노트: Reliable 고속 업링크의 포트 위치는 스위치 공급 업체나 모델에 따라 달라질 수 있습니다. MC-LAG는 여러 개의 독립적인 ToR(Top-of-Rack) 스위치를 단일 가상 섀시에 결합하는 스위치 상호 연결 기술입니다. MC-LAG는 링 크 집계(LAG) 포트 그룹이 여러 개의 섀시를 스팬할 수 있으므로 LAG 연결의 복구 성능이 향상됩니다. 또한, MC-LAG는 스패닝 트리 프로토콜(STP)을 사용하지 않고 사용 가능한 연결의 전체 대역폭을 사용하여 스위치에서 스위치로 전송되는 트래픽을 활성화하고 루프를 방지하기 위해 일부 링크를 비활성화하는 기능을 제공합니다. MC-LAG는 기술에 대한 일반적인 이름이지만, 일부 공급업체는 고유의 용어를 사용하여 MC-LAG 연결을 정의합니다. 표 16.
PowerStore Network Topology with a no MC-LAG interconnect Upstream Switch 2 Upstream Switch 1 Port Channels Top of Rack Switch 1 Port 0 Top of Rack Switch 2 Port 1 Port 1 Node A Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 11 .
노트: Reliable 고속 업링크의 포트 위치는 스위치 공급 업체나 모델에 따라 달라질 수 있습니다. 비-MC-LAG L2 연결에는 이중화된 고속 연결이 필요합니다. 노드에서 ToR(Top-of-Rack) 스위치로 연결 ToR(Top-of-Rack) 스위치를 배포하려면 NIC 및 스위치 수준에서 이중화를 제공할 수 있도록, 각 베이스 인클로저 어플라이언스 노드 가 각 ToR 스위치에 대한 연결을 최소한 한 개 이상 수립한 상태여야 합니다. 그림 12 . 노드에서 ToR 스위치로 케이블 연결 노드에서 스위치로 케이블 연결하는 경우: ● 동일한 노드의 포트 0 및 포트 1이 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 0과 노드 B의 포트 0은 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 1과 노드 B의 포트 1은 반대편 스위치에 연결돼야 합니다.
PowerStore T – Production Subnets Production ToR 1 ToR 2 PowerStore T Production Subnets Storage NAS Internal 그림 13 . 스토리지 서비스를 사용하는 PowerStore T 모델에 대한 네트워크 트래픽 PowerStore T 모델에서 위에 표시된 VLAN을 통해 통신할 수 있는지 확인합니다. 네트워크 공급 업체의 문서를 참조하시어 PowerStore T 모델에서 사용 중인 모든 네트워크에 알맞은 L2 및/또는 L3 트래픽이 모두 올바르게 라우팅되고 있는지 확인합니다. 표 17.
표 17. 스토리지 서비스를 추가할 때의 PowerStore T 모델 네트워크 (계속) 서브넷 설명 노드 전송 포트 내부 네트워크 통신은 기본 VLAN에서 수행됩니다. 내부 네트 워크가 사용됩니다. ● 클러스터 데이터베이스와 같은 내부 통신 및 클러스터 내 어플라이언스 간의 내부 통신 관리. 클러스터 내 관리 네트 워크는 IPSEC로 암호화됩니다. ● 어플라이언스 간의 스토리지 마이그레이션과 같은 클러스 터 내 데이터 이동성 트래픽. ● 유니파이드 어플라이언스에서 파일 서비스를 사용 설정하 기 위해 통신은 ToR 스위치가 아니라 PowerStore T 모델 어플라이언스 내에서 라우팅됩니다. 4포트 카드의 처음 2개 포트(LACP 본드) 네트워크를 구성하는 동안 다음 사항에 유의합니다.
PowerStore T – Management Network is Untagged Production ToR 1 ToR 2 PowerStore T Sample ID 200 300 102 Traffic Subnet PowerStore Storage NAS Servers Internal Untagged Traffic Tagged Traffic y.y.y.y/24 y.y.y.y/24 Internal IPv6 addressing 그림 14 . 스토리지 및 NAS 트래픽 노트: NAS 서버는 유니파이드 배포 시에만 사용할 수 있습니다. 여러 개의 NAS 서버를 실행하는 경우 여러 개의 VLAN을 사용할 수 있습니다. 스토리지 서비스 추가를 위한 스토리지 네트워크 IP 주소 요 구 사항 하나 이상의 스토리지 네트워크를 PowerStore T 모델 어플라이언스에 추가하려면 IP 주소를 예약해야 합니다. 추가하는 각 스토리지 네트워크에 대해 총계 3개의 IP 주소를 예약해야 합니다.
IPv4 또는 IPv6 주소 중 하나를 스토리지 네트워크에 할당하도록 선택할 수 있습니다. 서로 다른 IP 버전을 동일한 네트워크에 할당할 수는 없습니다. 노트: 향후 더 많은 어플라이언스를 추가할 수 있도록 하려면 추가로 IP 주소를 더 예약하는 것이 좋습니다.
11 Dell PowerSwitch Series S4148 ToR(Top-ofRack) 스위치를 사용하여 PowerStore T 모델 구 성 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: Dell EMC PowerSwitch Series S4148 스위치를 사용한 구성 개요 PowerStore T 모델 캐비닛 안에 ToR(Top-of-Rack) 스위치 설치 스토리지 서비스에 대한 Dell PowerSwitch Series 구성 • • • Dell EMC PowerSwitch Series S4148 스위치를 사용한 구 성 개요 이 문서에서는 Dell PowerSwitch Series S4148 관리 스위치에 연결된 단일 베이스 인클로저가 있는 어플라이언스 1개와 Dell PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치 2개로 구성된 단일 클러스터를 사용하여 PowerStore T 모델를 배포하는 단계에 대해 설명합니다.
PowerStore T 모델 어플라이언스를 배포하지 않는 경우에는 스위치 고유의 설명서에서 스위치를 캐비닛에 설치하는 단계를 참조 바 랍니다. 스토리지 서비스에 대한 Dell PowerSwitch Series 구성 iSCSI 호스트 접속 구성, 복제, 가져오기, 클러스터링 또는 NAS(Network Attached Storage)를 지원하려면 PowerStore T 모델에 최소 한 1개의 OOB(out-of-band) 관리 스위치와 2개의 ToR(Top-of-Rack) 스위치를 구성해야 합니다. 권장되는 대로 다음 단계에서는 2개의 ToR 스위치 간에 VLT(Virtual Link Trunking) L2(Layer 2) 상호 연결을 사용하여 2개의 ToR 스위 치를 구성하는 방법에 대해 설명합니다. VLT 상호 연결 없이 PowerStore T 모델 배포를 구성하는 단계는 VLTi 없이 PowerStore T 모 델 구성을 참조하십시오.
표 20. 스토리지 서비스용 스위치 리소스 워크시트(작성 완료) (계속) 단계 단계 세부 정보 참고 인터페이스당 최대 32 개의 스토리지 네트워크와 8개의 스 토리지 네트워크를 추가할 수 있습니다. 4. 5. 내부(태그 미지정) 1 NAS(유니파이드 배포에만 해당) 300 아래 ToR 스위치를 구성하는 데 필요한 IP 주소를 예약하고 기록합니다. ToR 스위치 1의 관리 IP 주소 100.0.100.10/24 ToR 스위치 2의 관리 IP 주소 100.0.100.11/24 기본 게이트웨이 100.0.100.1 NTP 서버 100.0.100.200 Dell EMC는 계층 2 상호 연결 링크를 사용하는 2개의 ToR(Top-of-Rack) 스위치를 사용하는 PowerStore T 모델 배포를 지원 합니다. 사용할 계층 2 상호 연결 유형을 선택합니다.
표 20. 스토리지 서비스용 스위치 리소스 워크시트(작성 완료) (계속) 단계 단계 세부 정보 참고 MC-LAG 연결이 없는 L2 업링크에는 2개의 포트 채널 ID가 필요합니다. 11. 1. MC-LAG가 없는 L2 업링크에 대한 포트 채널 ID 해당 없음 2. MC-LAG가 없는 L2 업링크에 대한 포트 채널 ID 해당 없음 가장 좋은 방법은 스패닝 트리 프로토콜을 ToR 스위치에 추가하는 것입니다. 각 스위치에 설정할 스패닝 트리 프로토콜을 기록합니다. ToR 스위치 1용 스패닝 트리 프로토콜 40960 ToR 스위치 2용 스패닝 트리 프로토콜 45056 스위치에 대한 터미널 세션 수립 Dell EMC PowerSwitch Series S4148 스위치에서 대한 직렬 콘솔에 대한 터미널 세션을 수립하려면 다음 단계를 수행합니다. 이 단계는 Dell EMC PowerSwitch S4148-ON 스위치 연결을 수립합니다.
8. 스위치에 처음으로 로그인한 후에는 암호를 변경하는 것이 좋습니다. 다음 명령을 사용하여 스위치 암호를 변경합니다. username admin password role sysadmin 스위치 버전 및 라이선스 검증 스위치 및 네트워크를 구성하기 전에 스위치 운영 체제 버전 및 라이선스를 확인하십시오. 스위치 OS를 업그레이드해야 하거나 스위치 라이선스를 다시 설치해야 하는 경우 자세한 내용은 OS10 Enterprise Edition 사용자 가이 드를 참조 바랍니다. 1. 스위치에 터미널 연결을 수립하고 연결된 후 Enter 키를 누릅니다. 2. show version 명령을 실행하여 OS 버전을 표시합니다. Dell EMC는 Dell Digital Locker(www.dell.com/support/software/)에서 이 용할 수 있는 최신 릴리스로 업그레이드하는 것을 권장합니다.
2. 글로벌 구성 모드를 시작합니다. configure terminal 3. 스위치의 호스트 이름을 구성합니다. hostname Switch1 4. 스위치의 관리 IP 주소를 구성합니다. 노트: 다음 명령 샘플에서는 DHCP(Dynamic Host Configuration Protocol)를 통한 자동 IP 할당이 스위치에서 활성화된 것으로 가정합니다. DHCP를 통한 자동 IP 할당이 활성화되어 있지 않은 경우 아래 명령에 no ip address dhcp를 포함할 필요가 없습니다. interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.10/24 exit 노트: 스위치 2를 구성 하는 경우 다른 IP 주소를 사용해야 합니다. 이 문서는 아래 예시에서 100.0.100.11/24를 사용합니 다. 5. 필요에 따라 스위치의 관리 경로(기본값 게이트웨이)를 구성합니다. management route 0.0.0.0/0 100.0.
Switch1 Switch2 exit exit Virtual Link Trunking interconnect 구성 2개의 ToR(Top of the Rack) PowerSwitch Series 간에 계층 2 상호 연결을 위해 VLT를 구현하도록 선택한 경우 다음 단계를 수행합니 다. VLTi 구현과 관련하여 네트워크 관리자와 상의가 필요합니다. VLTi 구성에는 네트워크 전문가가 필요합니다. 스위치 간에 연결을 구성하기 전에 스위치를 함께 케이블로 연결하거나, 연결 유형을 구성한 후 스위치를 케이블로 연결할 수 있습니 다. 자세한 내용은 ToR(Top-of-Rack) 스위치 케이블 연결을 참조 바랍니다. Powerstore 노드 간에 Link Aggregation Control 프로토콜을 구성하려면 VLTi가 필요합니다. 1. 첫 번째 ToR 스위치(Switch1)에 대해 터미널 연결을 수립합니다. 2. 글로벌 구성 모드를 시작합니다. configure terminal 3.
스위치 2를 구성하는 경우 동일한 VLT MAC 주소를 사용합니다. 9. 두 번째 스위치에도 위의 단계를 반복합니다. 이때는 아래 코드 샘플에 나와 있는 것처럼 5단계의 스위치 IP 주소를 거꾸로 적용합니다. 표 22. VLTi 구성 단계의 코드 샘플 스위치 1 스위치 2 configure terminal interface range ethernet 1/1/25-1/1/26 description vlti no switchport exit vlt-domain 1 discovery-interface ethernet 1/1/25-1/1/26 backup destination 100.0.100.
3. 노드 A 포트에 대한 VLT 포트 채널을 생성합니다. interface port-channel 10 description "LACP port channel for Node A" vlt-port-channel 10 4. 노드 A 포트와 ToR 스위치 1에 대한 기본 VLAN을 구성합니다. no shutdown switchport mode trunk switchport access vlan 1 5. PowerStore T 모델 노드에 연결되는 포트를 STP(spanning tree protocol) 엣지 포트로 구성합니다. spanning-tree port type edge exit 6. 노드 B 포트에 대한 VLT 포트 채널을 생성합니다. interface port-channel 20 description "LACP port channel for Node B" vlt-port-channel 20 7. 노드 B 포트와 ToR 스위치 1에 대한 기본 VLAN을 구성합니다.
스위치 1 스위치 2 configure terminal interface port-channel 10 description "LACP port channel for Node A" vlt-port-channel 10 no shutdown switchport mode trunk switchport access vlan 1 spanning-tree port type edge exit interface port-channel 20 description "LACP port channel for Node B" vlt-port-channel 20 no shutdown switchport mode trunk switchport access vlan 1 spanning-tree port type edge exit interface ethernet 1/1/1 channel-group 10 mode active flowcontrol receive off flowcontrol transmit off exit interfa
flowcontrol receive off flowcontrol transmit off 5. 구성을 NVRAM에 커밋합니다. copy running-configuration startup-configuration 6. 스위치 2에도 이 단계를 반복합니다.
5. 노드 B 포트에 대한 스토리지 VLAN 구성 interface port-channel 20 switchport trunk allowed 200 exit 6. 업링크에 대한 스토리지 VLAN 구성 interface port-channel 30 switchport trunk allowed 200 exit 7. 생성하는 각 iSCSI 스토리지 네트워크에 대해 3~6단계를 반복합니다. 8. 두 번째 ToR 스위치(Switch2)에 대해 1~7단계를 반복합니다. 표 23.
5. 노드 B 포트에 대한 스토리지 VLAN 구성 interface port-channel 20 switchport trunk allowed 300 exit 6. 업링크에 대한 스토리지 VLAN 구성 interface port-channel 30 switchport trunk allowed 300 exit 7. 생성하는 각 iSCSI 스토리지 네트워크에 대해 3~6단계를 반복합니다. 8. 두 번째 ToR 스위치(Switch2)에 대해 1~7단계를 반복합니다. 표 24.
12 스토리지 서비스에 대한 Dell PowerSwitch Series ToR 케이블 연결 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: ToR 스위치에 베이스 인클로저 케이블 연결 ToR 스위치와 함께 케이블 연결 ToR(Top-of-Rack) 스위치를 코어 업링크에 케이블로 연결합니다. • • • ToR 스위치에 베이스 인클로저 케이블 연결 노드를 ToR(Top of Rack) 스위치에 케이블로 연결합니다. 2 4 1 3 그림 15 . ToR 스위치에 베이스 인클로저 연결 다이어그램에 표시된 것처럼 ToR 스위치에 노드를 케이블로 연결 하는 경우: ● 동일한 노드의 포트 0 및 포트 1이 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 0과 노드 B의 포트 0은 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 1과 노드 B의 포트 1은 반대편 스위치에 연결돼야 합니다. 표 25.
ToR 스위치와 함께 케이블 연결 VLT를 사용하는 PowerStore 이중 스위치 배포는 2개의 ToR(Top of Rack) 스위치가 함께 케이블로 연결되어야 합니다. 1 2 그림 16 . 스위치-스위치 연결 고속 포트 간 연결을 지원하는 케이블 2개를 사용합니다(예: 100Gbps DAC(Direct Attached Cable)). 표 26. 사용 가능한 스위치-스위치 포트 PowerSwitch 100 GbE 포트 S4148F-ON 25, 26, 29 및 30 S4148T-ON 25, 26, 29 및 30 S5248F-ON 49-54 상단 및 하단 스위치 쌍에 동일한 포트 번호를 사용하는 것이 좋습니다. 표 27. 스위치를 함께 연결하는 단계 1 하단 스위치(1)의 100GbE 포트 25를 상단 스위치(2)의 100GbE 포트 25에 연결합니다. 2 하단 스위치(1)의 100GbE 포트 26를 상단 스위치(2)의 100GbE 포트 26에 연결합니다.
Core uplinks Uplink A 1 Uplink B 3 4 2 그림 17 . Dell EMC PowerSwitch Series S4148-ON ToR 스위치를 코어 업링크에 연결 표 28. Dell EMC PowerSwitch Series S4148-ON ToR 스위치를 코어 업링크에 연결하는 단계 1 하단 ToR 스위치의 포트 30을 코어 업링크 A에 연결합니다. 2 하단 ToR 스위치의 포트 29를 코어 업링크 B에 연결합니다. 3 상단 ToR 스위치의 포트 29를 코어 업링크 A에 연결합니다. 4 상단 ToR 스위치의 포트 30을 코어 업링크 B에 연결합니다. 노트: 네트워크 관리자와 상의하여 ToR 스위치가 연결될 업링크 포트를 결정합니다.
13 ToR 스위치를 사용하여 PowerSwitch Series 구 성 검증 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • ToR(Top-of-Rack) 스위치의 구성 검증 ToR(Top-of-Rack) 스위치를 PowerStore T 모델 배포에 추가한 후 네트워크 유효성 검사 도구 ToR(Top-of-Rack) 스위치의 구성 검증 ToR 스위치를 구성하고 케이블을 연결했으면 PowerStore T 모델 모델 배포를 검색하기 전에 구성을 검증합니다. 1. 스위치에 터미널 세션을 수립합니다. 2. 인터페이스 상태를 검증합니다.
5.
9. VLT 포트 구성을 검증합니다.
14 PowerStore Manager에서 스토리지 및 NAS 네 트워크 구성 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • PowerStore Manager에서 iSCSI 스토리지 네트워크 생성 PowerStore Manager에서 NAS(Network Attached Storage) 서비스 생성 PowerStore Manager에서 iSCSI 스토리지 네트워크 생성 스토리지 서비스에 대한 ToR 스위치를 구성한 후에는 PowerStore Manager에서 iSCSI 지원을 위해 스토리지 네트워크를 생성해야 합 니다. PowerStore는 4포트 카드의 포트마다 최대 8개를 사용하여 최대 32개의 스토리지 네트워크를 지원합니다. PowerStore Manager에 추가하는 각 스토리지 네트워크에 대해 작성된 스토리지 네트워크 구성 워크시트를 가져옵니다. 다음 스토리지 네트워크 구성 워크시트는 이 가이드에 사용된 네트워크 리소스로 작성되었습니다.
3. iSCSI 네트워크용으로 예약된 리소스를 사용하여 Create Storage Network 마법사를 통해 실행합니다. 4. 워크시트를 작성하고 추가하는 각 네트워크에 대해 1~3단계를 통해 실행합니다. ToR 스위치에 대한 연결을 사용하여 구성한 4개의 각 포트 노드에서 최대 8개의 스토리지 네트워크를 추가할 수 있습니다. 다른 스토리지 네트워크를 추가할 추가 스위치 및 노드 포트를 구성하는 단계는 추가 스토리지 네트워크용 포트 구성을 참조하십 시오. PowerStore Manager에서 NAS(Network Attached Storage) 서비스 생성 NAS 서비스는 PowerStore Manager Initial Configuration Wizard에서 Unified 모드를 선택하면 활성화됩니다. PowerStore Manager를 구성한 후에는 NAS 서버를 생성할 때 PowerStore Manager에서 네트워크가 생성됩니다.
A 여러 포트에서 실행하도록 스토리지 네트워크 확 장 부록에는 다음과 같은 정보가 포함되어 있습니다. 주제: • 스토리지 네트워크 확장 스토리지 네트워크 확장 PowerStore T 모델 어플라이언스의 여러 포트에서 실행하도록 스토리지 네트워크를 확장할 수 있습니다. 스토리지 네트워크를 확장하는 단계를 수행하려면 다음 정보가 필요합니다. 노트: 아래의 샘플 네트워크 리소스는 2개의 Dell EMC PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에서 스토리지 서비스 추가에 구성된 스토리지 네트워크를 확장하는 데 사용할 수 있습니다. 이 가이드에 설명된 것과 동일한 스토리지 네트워크를 구 성하지 않은 경우 샘플 리소스를 해당 환경에 맞는 값으로 교체합니다. 표 30.
1 2 그림 18 . 추가 포트 케이블 연결 1. 하단 노드(A)의 포트 2를 하단 스위치(1)의 포트 2에 연결합니다. 2. 상단 노드(B)의 포트 2를 상단 스위치(2)의 포트 53에 연결합니다. ToR 스위치에서 VLAN 구성 다음 단계에서는 2개의 Dell PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 VLAN을 구성하는 예시를 제공합니다. 이러한 단계를 수행하기 전이나 후에 PowerStore T 모델 어플라이언스 노드를 스위치에 케이블로 연결할 수 있습니다. 자세한 단계 는 노드를 ToR 스위치에 케이블로 연결을 참조하십시오. 스토리지 네트워크가 생성된 VLAN을 사용하여 추가 ToR 스위치 포트를 이미 구성한 경우 이 단계를 건너뛸 수 있습니다. 다음 목록은 스토리지 네트워크 리소스를 참조하십시오. ● 스토리지 네트워크를 확장하는 데 필요한 네트워크 리소스 ● 다음 단계에서 사용되는 샘플 값 1.
표 31. iSCSI 스토리지 네트워크를 확장하도록 ToR 스위치를 구성하는 코드 샘플 ToR 스위치 1 configure terminal interface ethernet 1/1/2 switchport mode trunk switchport trunk allowed vlan 200 no shutdown exit ToR 스위치 2 configure terminal interface ethernet 1/1/53 switchport mode trunk switchport trunk allowed vlan 200 no shutdown exit IP 주소 추가 및 스토리지 네트워크 매핑 스토리지 네트워크 확장을 위해 ToR(Top-of-Rack) 스위치를 구성하고 케이블로 연결한 후에는 PowerStore Manager에서 IP 주소를 추가하고 확장할 포트를 매핑해야 합니다. 다음 목록은 스토리지 네트워크 리소스를 참조하십시오.
B 추가 스토리지 네트워크 생성 이 부록에서 다루는 내용은 다음과 같습니다. 주제: 새 스토리지 네트워크 생성 • 새 스토리지 네트워크 생성 4포트 카드의 포트마다 또는 노드의 I/O 모듈마다 최대 8개의 네트워크를 사용하여 최대 32개의 스토리지 네트워크를 구성할 수 있 습니다. 새 스토리지 네트워크를 생성하는 단계를 수행하려면 다음 정보가 필요합니다. 노트: 아래의 샘플 네트워크 리소스는 스토리지 서비스 추가에 설명된 대로 원래 스토리지 네트워크에 구성된 2개의 Dell EMC PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 사용할 수 있습니다. 이 가이드에 설명된 것과 동일한 Dell EMC PowerSwitch Series S4148 ToR 스위치를 사용하지 않은 경우 샘플 리소스를 해당 환경에 맞는 값으로 교체합니다. 표 32.
다이어그램에 표시된 것처럼 노드를 ToR 스위치에 케이블을 연결하면 하단 노드(A)와 상단 노드(B)가 반대편 스위치에 케이블로 연 결되어 있어야 합니다. 1 2 그림 19 . 추가 포트 케이블 연결 1. 하단 노드(A)의 포트 2를 하단 스위치(1)의 포트 2에 연결합니다. 2. 상단 노드(B)의 포트 2를 상단 스위치(2)의 포트 53에 연결합니다. ToR 스위치에서 스토리지 네트워크 구성 다음 단계에서는 2개의 Dell PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 스토리지 네트워크를 구성하는 예시를 제공합니 다. 이러한 단계를 수행하기 전이나 후에 PowerStore T 모델 어플라이언스 노드를 스위치에 케이블로 연결할 수 있습니다. 자세한 단계 는 노드를 ToR 스위치에 케이블로 연결을 참조하십시오. 다음 목록은 새 스토리지 네트워크 리소스를 참조하십시오.
4. ToR 스위치 1에서 포트 2를 통해 실행되도록 스토리지 네트워크를 구성합니다. interface ethernet 1/1/2 switchport mode trunk switchport trunk allowed vlan 210 no shutdown 5. ToR 스위치 2에서 포트 53을 사용하여 1단계를 반복합니다. 표 33.
C VLT 상호 연결 없이 ToR 스위치를 사용하여 PowerStore T 모델 구성 이 부록에서 다루는 내용은 다음과 같습니다. 주제: • VLT 없이 ToR 스위치를 사용한 PowerStore T 모델 구성 단계 VLT 없이 ToR 스위치를 사용한 PowerStore T 모델 구성 단계 다음은 Virtual Link Trunking interconnect 없이 2개의 ToR(Top-of-Rack) 스위치를 사용하여 PowerStore T 모델를 배포하는 데 필요한 단계입니다. PowerSwitch Series를 구성하는 다음 단계에 대한 구체적인 코드 샘플은 ToR 스위치를 사용한 배포를 위해 Dell PowerSwitch Series 구성에서 사용할 수 있습니다. 스위치에 터미널 세션을 수립합니다. 스위치 버전 및 라이선스를 검증합니다. 각 스위치에 대해 1, 2단계를 반복합니다. OOB 관리 스위치를 구성합니다. ToR 스위치에서 일반 설정을 구성합니다.
D 기타 Dell EMC PowerSwitch Series 구성 작업 이 부록에서 다루는 내용은 다음과 같습니다. 주제: Dell EMC SmartFabric 서비스 스위치를 공장 출하 설정으로 재설정 PowerStore T 모델 배포에 사용되는 PowerSwitch Series의 실행 구성 • • • Dell EMC SmartFabric 서비스 Dell EMC SmartFabric 서비스는 작업의 최대 98%까지 자동화된 포괄적인 패브릭을 지원하므로 클러스터 및 네트워크 확장을 위해 2 일 차 네트워크 운영에 대한 단순성과 민첩성을 제공합니다. vCenter를 통한 단일 관리 창에서 사용자는 vCenter 내에서 하나 이상의 패브릭에 대한 수명 주기 관리를 운영하고 수행할 수 있습니다. Dell EMC SmartFabric 서비스를 PowerStore 네트워크 배포에 적용하려는 경우 다음 문서에서 자세한 내용을 참조하십시오. 표 34.
Dell PowerSwitch Series S4148 스위치가 관리 및 ToR(Top-of-Rack) 스위치에 사용되는 경우 실행 구성 파일을 생성하려면 다음 명령 을 사용합니다. show running-configuration 관리 스위치의 실행 구성 예시 ! Version 10.4.1.4 ! Last configuration change at Mar 19 04:19:20 2020 ! snmp-server contact http://www.dell.com/support hostname powerstoreMgmtSwitch interface breakout 1/1/25 map 100g-1x interface breakout 1/1/26 map 100g-1x interface breakout 1/1/29 map 100g-1x interface breakout 1/1/30 map 100g-1x username admin password $6$rounds=656000$.zmPnShW0cq6sTTl$8VG.
! interface ethernet1/1/5 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/6 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/7 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/8 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/9 shutdown switchport access vlan 1 flowcontrol rece
interface ethernet1/1/17 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/18 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/19 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/20 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/21 shutdown switchport access vlan 1 flowcontrol r
flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/31 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/32 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/33 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/34 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1
flowcontrol transmit off ! interface ethernet1/1/43 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/44 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/45 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/46 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/47 shutdown switchport
flowcontrol transmit off ! interface mgmt1/1/1 no shutdown no ip address dhcp ip address 100.0.100.50/24 ipv6 address autoconfig ! management route 0.0.0.0/0 100.0.100.1 ! support-assist 표 35. ToR 스위치의 실행 구성 예시 Switch1 ! Version 10.4.1.4 ! Last configuration change at Mar 19 04:24:55 2020 ! snmp-server contact http://www.dell.
표 35.
표 35.
표 35.
표 35.
표 35.