Dell EMC PowerStore PowerStore X 모델을 위한 네트워킹 가이드 버전 2.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2020 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자 의 상표일 수 있습니다.
목차 추가 리소스.....................................................................................................................................5 장 1: 개요........................................................................................................................................ 6 PowerStore X 모델 어플라이언스 개요............................................................................................................................6 지원되는 스위치...............................................................
장 8: PowerStore X 모델 어플라이언스의 초기 구성............................................................................ 41 초기 구성 마법사.................................................................................................................................................................41 작성된 초기 구성 워크시트 가져오기............................................................................................................................ 42 부록 A: 여러 포트에서 실행하도록 스토리지 네트워크 확장..............................................
서문 제품군을 향상시키기 위한 노력의 일환으로 소프트웨어와 하드웨어의 개정 버전을 정기적으로 릴리스하고 있습니다. 이 문서에서 설 명하는 일부 기능은 현재 사용 중인 소프트웨어 또는 하드웨어의 일부 버전에서 지원되지 않을 수 있습니다. 제품 릴리스 노트에는 제 품 기능에 대한 최신 정보가 제공되어 있습니다. 제품이 올바르게 작동하지 않거나 이 문서에 설명된 대로 작동하지 않는 경우 서비스 공급업체에 문의하십시오. 지원 정보 지원, 제품 및 라이선스 정보는 다음과 같이 확인할 수 있습니다. ● 제품 정보 제품 및 기능 설명서 또는 릴리스 노트를 보려면 https://www.dell.com/powerstoredocs에서 PowerStore 설명서 페이지를 참조 바 랍니다. ● 문제 해결 제품, 소프트웨어 업데이트, 라이선스 등록 및 서비스에 대한 자세한 내용은 https://www.dell.com/support에서 해당 제품 지원 페 이지를 참조 바랍니다.
1 개요 이챕터에는 다음과 같은 정보가 포함되어 있습니다. 주제: • • PowerStore X 모델 어플라이언스 개요 지원되는 스위치 PowerStore X 모델 어플라이언스 개요 PowerStore X 모델은 시스템에 하이퍼바이저가 설치된 블록(SAN 전용) 및 vVol 워크로드를 지원합니다. 시스템 소프트웨어는 하이 퍼바이저에 구축되며 따라서 하드웨어 내에 VM(virtual machines) 및 고객 애플리케이션 구축이 가능합니다. PowerStore X 모델 모델 번호: ● ● ● ● ● 1000X 3000X 5000X 7000X 9000X 노트: 이 모델에서는 파일(NAS(network attached storage)) 서비스가 제공되지 않습니다. 파일 서비스는 PowerStore T 모델 어플 라이언스에서 지원됩니다. 지원 설명서 스위치와 네트워크를 구성하기 전에, 이 문서를 읽는 것 외에도 다음 가이드를 참조 바랍니다.
표 1. PowerSwitch 문서 리소스 문서 참조 위치 Dell EMC PowerSwitch S4100-on PowerSwitch 사이트 준비 요구 사항, 랙 마운 Dell EMC S4148F-ON 및 S4148T ON 스위치의 경 Series 설치 안내서 팅 및 데스크 마운팅, 모듈 삽입, 전원 연결에 우, Dell EMC PoweSwitch S4148-ON/S4148T대한 단계별 절차. ON/S4148FE-ON 문서 페이지를 참조 바랍니다. S5200F-ON Series 설치 가이드 https://www.dell.com/support/home/us/en/04/ OS10 Enterprise Edition 사용자 운영 체제 설치, 원격 스위치 액세스, 스위치 product-support/product/networking-s4148f-on/ 가이드 명령 실행에 필요한 단계가 포함되어 있습니 docs 다.
2 스위치 및 네트워크를 구성하기 위한 준비 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: PowerStore X 모델 네트워크 설정 준비 워크시트 초기 구성 워크시트 • • PowerStore X 모델 네트워크 설정 준비 워크시트 네트워크 관리자와 협력하여 네트워크 설정 준비 워크시트를 작성하고 스위치를 구성하는 데 필요한 정보를 예약합니다. 네트워크 설정 준비 워크시트를 작성하는 동안에도 네트워크 관리자와 협력하여 초기 구성 워크시트를 작성하는 것이 좋습니다. Dell EMC PowerSwitch Series S4148-ON 스위치에 대해 작성된 네트워크 설정 준비 워크시트의 샘플은 PowerStore X 모델 네트워크 설정 준비 워크시트 작성 예시를 참조하십시오. 표 2. PowerStore X 모델 네트워크 설정 준비 워크시트(비어 있음) 단계 단계 세부 정보 참고 1. 이 표를 인쇄하여 예약된 리소스를 기록합니다. 2.
표 2. PowerStore X 모델 네트워크 설정 준비 워크시트(비어 있음) (계속) 단계 단계 세부 정보 참고 스위치 1의 관리 IP 주소 스위치 2의 관리 IP 주소 기본 게이트웨이 NTP 서버 8. Dell EMC는 계층 2 상호 연결 링크를 사용하는 2개의 ToR(Top-of-Rack) 스위치를 사용하는 PowerStore X 모델 배포를 지원 합니다. 사용할 계층 2 상호 연결 유형을 선택합니다. 매우 권장됨: MC-LAG(Multi-chassis Link Aggregation Group) MC-LAG를 사용하는 경우 스위치를 함께 연결하는 데 사용할 포트를 기록합니다. 스위치 포트 페어 1로 전환 스위치 포트 페어 2로 전환 또는 MC-LAG가 없는 L2 업링크 9. MC-LAG를 사용하는 경우 도메인 ID를 입력합니다. 10 계층 2 상호 연결에 VLT를 사용하는 경우 다음을 기록 합니다. 스위치 1과 스위치 2 모두에 사용할 VLT MAC 주소.
표 2. PowerStore X 모델 네트워크 설정 준비 워크시트(비어 있음) (계속) 단계 단계 세부 정보 참고 14. 위의 단계를 완료하면 스위치를 구성하는 데 필요한 정보가 준비될 것입니다. 네트워크 관리자와 계속해서 상의하여 초기 구성 워크시트를 작성하고 다음을 확실히 하는 것이 좋습니다. ● 스위치의 네트워크 구성이 PowerStore X 모델에서 수행한 네트워크 구성과 일치합니다. ● PowerStore X 모델 네트워크의 배포를 완료하기 위해 필요한 네트워크 리소스를 예약합니다. 15. PowerStore 검색에 직접 연결을 사용할지 원격 연결을 사용할지 결정합니다. PowerStore를 성공적으로 검색한 후, Initial Configuration Wizard를 통해 PowerStore 클러스터를 생성합니다. 초기 구성 워크시트 네트워크 관리자와 협력하여 초기 구성 워크시트를 작성합니다.
표 3. 초기 구성 워크시트 (계속) 클러스터에는 네트워크 유형에 대한 전용 IP 주소 세트가 필요합니다. 노트: 관리, 스토리지, vMotion 네트워크에 대한 VLAN 정보는 선택 사항이며 기본값은 0입니다. 네트워크 트래픽에 태그가 지정 되지 않고, 스위치를 이용하여 기본 VLAN이 적용됨을 나타내는 데 사용되는 마커입니다. 보안 및 성능 향상을 위해 각 네트워크 유형에 대해 고유한 VLAN 정보를 지정하는 것이 좋습니다. 단일 VLAN으로 배포하는 경우 각 네트워크 유형에 대해 고유한 서브넷을 구성하는 것이 좋습니다. 클러스터 IP 주소 관리 네트워크 DNS 및 NTP와 같은 서비스에 클러스터를 연결합니다. 관리 네트워크의 IP 주소는 클러스터, 어플라이언스, 컨트롤러 및 내부 호스 트를 처리하는 데 사용됩니다.
표 3. 초기 구성 워크시트 (계속) 물리적/ToR(Top-of-Rack) 스위치 정보 클러스터를 구성하기 전에 스위치 IP 주소를 기록하여 케이블 연결 및 스위치 설정을 확인합니다. 스위치 자격 증명은 PowerStore X 모델에 스위치에 대한 읽기 전용 액세스 권한을 제공하여 스위치의 구성이 클러스터 네트워크를 지원하는지 검증합니다. 스위치 이름 프로토콜 (SSH/SNMP) IP 주소 포트 SSH 사용자 이름 스위치 암호 하이퍼바이저 기존 vCenter 관리자 로그인 자격 증명을 기록합니다. 초기 구성 워크플로가 데이터 센터 및 ESXi 클러스터를 자동으로 생성하고 이 를 클러스터와 연결합니다. 노트: vCenter Server를 로컬 네트워크에서 사용할 수 있는지 확인합니다.
표 3.
3 PowerStore X 모델: 네트워크 구성 요구 사항 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: ToR(Top-of-Rack) 스위치 연결 구성 옵션 및 요구 사항 PowerStore X 모델 네트워크 PowerStore X 모델 네트워크 VLAN 옵션 네트워크 구성 시 IP 주소 • • • • ToR(Top-of-Rack) 스위치 연결 구성 옵션 및 요구 사항 PowerStore는 ToR(Top-of-Rack) 스위치 쌍에 연결해야 합니다. 이 섹션에서는 다음 요구 사항에 대해 설명합니다. ● 스위치에서 스위치(L2) 연결 ● 노드에서 ToR 스위치 연결 ToR(Top-of-Rack) 스위치와 ToR 스위치(L2) 연결 옵션 다음 옵션 중 하나를 사용하여 두 ToR 스위치를 함께 연결합니다. 표 4. ToR 스위치-ToR 스위치 상호 연결 옵션 스위치 상호 연결 옵션 권장 사항 1.
PowerStore Network Topology with Top of Rack Switches and MC-LAG Interconnect Upstream Switch 2 Upstream Switch 1 Port Channel Top of Rack Switch 1 Port 0 MC-LAG Interconnect Port 1 Top of Rack Switch 2 Port 1 Node A Port 0 Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 1 .
노트: Reliable 고속 업링크의 포트 위치는 스위치 공급 업체나 모델에 따라 달라질 수 있습니다. MC-LAG는 여러 개의 독립적인 ToR(Top-of-Rack) 스위치를 단일 가상 섀시에 결합하는 스위치 상호 연결 기술입니다. MC-LAG는 링 크 집계(LAG) 포트 그룹이 여러 개의 섀시를 스팬할 수 있으므로 LAG 연결의 복구 성능이 향상됩니다. 또한, MC-LAG는 스패닝 트리 프로토콜(STP)을 사용하지 않고 사용 가능한 연결의 전체 대역폭을 사용하여 스위치에서 스위치로 전송되는 트래픽을 활성화하고 루프를 방지하기 위해 일부 링크를 비활성화하는 기능을 제공합니다. MC-LAG는 기술에 대한 일반적인 이름이지만, 일부 공급업체는 고유의 용어를 사용하여 MC-LAG 연결을 정의합니다. 표 5.
PowerStore Network Topology with a no MC-LAG interconnect Upstream Switch 2 Upstream Switch 1 Port Channels Top of Rack Switch 1 Port 0 Top of Rack Switch 2 Port 1 Port 1 Node A Port 0 Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 그림 2 .
노트: Reliable 고속 업링크의 포트 위치는 스위치 공급 업체나 모델에 따라 달라질 수 있습니다. 비-MC-LAG L2 연결에는 이중화된 고속 연결이 필요합니다. 노드에서 ToR(Top-of-Rack) 스위치로 연결 ToR(Top-of-Rack) 스위치를 배포하려면 NIC 및 스위치 수준에서 이중화를 제공할 수 있도록, 각 베이스 인클로저 어플라이언스 노드 가 각 ToR 스위치에 대한 연결을 최소한 한 개 이상 수립한 상태여야 합니다. 그림 3 . 노드에서 ToR 스위치로 케이블 연결 노드에서 스위치로 케이블 연결하는 경우: ● 동일한 노드의 포트 0 및 포트 1이 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 0과 노드 B의 포트 0은 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 1과 노드 B의 포트 1은 반대편 스위치에 연결돼야 합니다. PowerStore X 모델 네트워크 PowerStore X 모델의 모든 네트워크가 고유해야 합니다.
그림 4 . PowerStore X 모델 네트워크 트래픽 PowerStore X 모델 인터페이스가 위에 표시된 VLAN을 통해 서로 통신할 수 있는지 확인합니다. 네트워크 공급 업체의 문서를 참조하 시어 PowerStore X 모델에서 사용 중인 모든 네트워크에 알맞은 L2 및/또는 L3 트래픽이 모두 올바르게 라우팅되고 있는지 확인합니 다. 표 6. PowerStore X 모델 네트워크 Network 트래픽 유형 노드 전송 포트 PowerStore 검색 유틸리티를 사용한 초기 검색.
PowerStore X 모델 네트워크 VLAN 옵션 다음 표에는 PowerStore X 모델 어플라이언스의 샘플 VLAN ID 및 다양한 유형의 네트워크에 대한 예가 나와 있습니다. 표 7. PowerStore X 모델 VLAN 구성 샘플 VLAN ID Network VLAN 포트 서브넷 예시 1 원격 검색(기본 VLAN를 통해 실행) 태그 미지정 169.254.x.x/16 100 관리 태그 지정됨 y.y.y.y/24 200 Storage 태그 지정됨 y.y.x.y/24 400 vMotion 태그 지정됨 y.y.a.y/24 1 내부(기본 VLAN를 통해 실행) 태그 미지정 내부 IPv6 주소 지정 태그되지 않은 트래픽 PowerStore 네트워크에 기본 VLAN를 사용하려면 PowerStore Initial Configuration Wizard에서 태그가 지정되지 않은 모든 트래픽 에 대해 VLAN ID 0을 입력해야 합니다.
표 8. 초기 구성 IP 주소 요구 사항 (계속) Network IP 주소 할당 클러스터당 vMotion 네트워크 IP 주소 수 (선택 사항) 글로벌 스토리지 검색 IP 주소(스토리지 네트워 크) 0개 필요, 1개 권장 VLAN 또는 서브넷 1개당 필요한 vMotion 수 2 장치당 노드 A 1 노드 B 1 IPv4 또는 IPv6 주소 중 하나를 관리 네트워크, 스토리지 네트워크, 또는 vMotion 네트워크에 할당하도록 선택할 수 있습니다. 같은 네 트워크에 서로 다른 IP 버전을 할당할 수는 없습니다. 예를 들어, 관리 네트워크에 할당된 6개의 모든 IP는 전부 IPv4이거나 IPv6이어 야 합니다. 서로 다른 네트워크에 서로 다른 IP 버전을 사용할 수는 있습니다. 예를 들어, 관리 네트워크에는 IPv4를 사용하고 스토리 지 네트워크에는 IPv6을 사용할 수 있습니다.
4 Dell EMC PowerSwitch Series S4148-ON 스위 치를 사용한 구성 이 챕터에서 다루는 내용은 다음과 같습니다.
표 9. 네트워크 설정 준비 워크시트(작성 완료) (계속) 단계 단계 세부 정보 참고 노드 A, 포트 1 -> ToR 2 포트 1 노드 B, 포트 0 -> ToR 2 포트 54 노드 B, 포트 1 -> ToR 1 포트 54 3. 스위치를 구성하는 동안 검색에 사용할 스위치 포트를 기록 합니다. 포트 13 4. 시스템 관리에 사용되는 VLAN ID를 기록합니다. 5. 6. 7. 원격 검색(태그 미지정) 1 관리(태그 지정됨) 100 프로덕션에 사용될 VLAN ID를 기록합니다. 스토리지 네트워크(태그 지정됨) 200 vMotion(태그 지정됨) 400 내부(태그 미지정) 1 아래 스위치를 구성하는 데 필요한 IP 주소를 예약하고 기록합니다. 스위치 1의 관리 IP 주소 100.0.100.10/24 스위치 2의 관리 IP 주소 100.0.100.11/24 기본 게이트웨이 100.0.100.1 NTP 서버 100.0.100.
표 9. 네트워크 설정 준비 워크시트(작성 완료) (계속) 단계 단계 세부 정보 참고 11. ToR 스위치와 업링크 간의 연결에 사용되는 포트 채널 ID를 기록합니다. MC-LAG로 배포하는 경우 업링크용 포트 채널 ID를 입력합 니다. 포트 채널 30 MC-LAG에는 단일 포트 채널 ID만 필요합니다. 또는 MC-LAG가 없는 L2 업링크에 필요한 업링크 포트 채널 ID를 기록합니다. MC-LAG 연결이 없는 L2 업링크에는 2개의 포트 채널 ID가 필요합니다. 12. 1. MC-LAG가 없는 L2 업링크에 대한 포트 채널 ID 해당 없음 2. MC-LAG가 없는 L2 업링크에 대한 포트 채널 ID 해당 없음 가장 좋은 방법은 스패닝 트리 프로토콜을 ToR 스위치에 추가하는 것입니다. 각 스위치에 설정할 스패닝 트리 프로토콜을 기록합니다. ToR 스위치 1용 스패닝 트리 프로토콜 40960 ToR 스위치 2용 스패닝 트리 프로토콜 45056 13.
표 10. 직렬 연결 설정 (계속) 설정 값 정지 비트 1 동일 수준 없음 흐름 제어 없음 5. 터미널 에뮬레이터 프로그램을 사용하여 스위치에 연결합니다. 6. 스위치 로그인 자격 증명을 입력합니다. 기본값 사용자 이름과 암호는 다음과 같습니다. ● 사용자 이름: admin ● 암호: admin 7. 글로벌 구성 모드를 시작합니다. configure terminal 8. 스위치에 처음으로 로그인한 후에는 암호를 변경하는 것이 좋습니다. 다음 명령을 사용하여 스위치 암호를 변경합니다. username admin password role sysadmin 스위치 버전 및 라이선스 검증 스위치 및 네트워크를 구성하기 전에 스위치 운영 체제 버전 및 라이선스를 확인하십시오. 스위치 OS를 업그레이드해야 하거나 스위치 라이선스를 다시 설치해야 하는 경우 자세한 내용은 OS10 Enterprise Edition 사용자 가이 드를 참조 바랍니다. 1.
License Status : Active License location: /mnt/license/D8MSG02.lic --------------------------------------------------------노트: OS10EE가 공장 출하 기본값으로 설치되어 있는 경우 스위치에 이미 영구적인 라이선스가 등록되어 있습니다. 4. 각 스위치에 대해 이러한 단계를 반복합니다. ToR(Top-of-Rack) 스위치 일반 설정 구성 ToR 스위치에 일반 설정을 구성하려면 다음 단계를 수행합니다. OS10EE에서는 기본값으로 각 인터페이스에서 LLDP(Link Layer Discovery Protocol)가 전역적으로 활성화됩니다. LLDP를 사용하여 문 제를 해결하고 검증을 수행할 수 있습니다. 스위치의 LLDPU(Link Layer Discovery Protocol Data Units)에서 선택 가능한 TLV를 모두 (유형, 길이, 값) 활성화하는 것이 좋습니다. 1.
9. 스위치의 스패닝 트리 우선 순위를 구성합니다. spanning-tree rstp priority 40960 spanning-tree rstp priority 값을 선택하는 경우 다음을 참조합니다. ● 네트워크의 다른 스위치와 충돌하는 것을 방지하기 위해 네트워크 관리자와 상의하여 사용할 값을 결정해야 합니다. ● Switch1과 Switch2를 구성하는 경우 다양한 rstp 우선 순위 값을 사용해야 합니다. ● 0 순위는 일반적으로 루트 브리지를 위해 예약되어 있습니다. 10. 두 번째 스위치(Switch2)에도 위 단계를 반복합니다.
no shutdown exit 6. vMotion VLAN을 생성합니다. interface vlan 400 description vMotion_Network no shutdown exit 7. 스위치 2에도 이 단계를 반복합니다.
● Switch1의 경우 백업에 Switch2 관리 IP 주소를 사용합니다. ● Switch2의 경우 백업에 Switch1 관리 IP 주소를 사용합니다. backup destination 100.0.100.11 6. 피어 라우팅을 활성화하여 업링크를 구성합니다. 피어 라우팅은 피어에 대한 L3 라우팅을 활성화하거나 비활성화합니다. 노트: 이 가이드에는 고객 네트워크에 업링크를 구성하는 단계에 대한 설명이 나와 있지 않습니다. peer-routing 7. 스위치의 우선순위를 설정합니다. primary-priority 1 유효한 우선순위 값의 범위는 1~65535입니다. 우선순위 설정이 낮은 스위치가 우선순위 값이 더 높은 스위치보다 우선됩니다. ToR 스위치 2개에 동일한 우선순위 값을 설정하면 안됩니다. 8. 네트워크의 충돌을 방지하기 위해 VLT MAC 주소를 입력합니다. 노트: VLT MAC 주소에는 0만 사용할 수 없습니다(00:00:00:00:00).
no shutdown switchport mode trunk switchport access vlan 1 switchport trunk allowed vlan 100,200,400 flowcontrol receive off flowcontrol transmit off spanning-tree port type edge exit 4. 아래에 나온 것처럼 노드 B, 포트 1의 스위치 1에도 이 단계를 반복합니다. 노트: iSCSI 모범 사례에 대해서는 아래에 설명된 대로 흐름 제어를 비활성화하는 것이 좋습니다.
2. 글로벌 구성 모드를 시작합니다. configure terminal 3. 업링크에 대한 포트 채널을 구성합니다. interface port-channel 30 description Uplink no shutdown switchport mode trunk switchport access vlan 1 switchport trunk allowed vlan 100,200,400 vlt-port-channel 30 4. 스위치에서 업링크 포트를 구성합니다. 노트: iSCSI 모범 사례에 대해서는 아래에 설명된 대로 흐름 제어를 비활성화하는 것이 좋습니다.
5 PowerStore X 모델: 어플라이언스를 스위치에 케이블로 연결 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: ToR 스위치에 베이스 인클로저 케이블 연결 ToR 스위치와 함께 케이블 연결 ToR(Top-of-Rack) 스위치를 코어 업링크에 케이블로 연결 • • • ToR 스위치에 베이스 인클로저 케이블 연결 노드를 ToR(Top of Rack) 스위치에 케이블로 연결합니다. 2 4 1 그림 5 . ToR 스위치에 베이스 인클로저 연결 다이어그램에 표시된 것처럼 ToR 스위치에 노드를 케이블로 연결 하는 경우: ● 동일한 노드의 포트 0 및 포트 1이 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 0과 노드 B의 포트 0은 반대편 스위치에 연결돼야 합니다. ● 노드 A의 포트 1과 노드 B의 포트 1은 반대편 스위치에 연결돼야 합니다. 표 13. 스위치 케이블 연결 단계 1 하단 노드(A)의 포트 0을 하단 스위치(1)의 포트 1에 연결합니다.
표 13. 스위치 케이블 연결 단계 (계속) 4 상단 노드(B)의 포트 0을 상단 스위치(2)의 포트 54에 연결합니다. ToR 스위치와 함께 케이블 연결 VLT를 사용하는 PowerStore 이중 스위치 배포는 2개의 ToR(Top of Rack) 스위치가 함께 케이블로 연결되어야 합니다. 1 2 그림 6 . 스위치-스위치 연결 고속 포트 간 연결을 지원하는 케이블 2개를 사용합니다(예: 100Gbps DAC(Direct Attached Cable)). 상단 및 하단 스위치 쌍에 동일한 포트 번호를 사용하는 것이 좋습니다. 표 14. Dell EMC S4148-ON 스위치를 함께 연결하는 단계 1 하단 스위치(1)의 100GbE 포트 25를 상단 스위치(2)의 100GbE 포트 25에 연결합니다. 2 하단 스위치(1)의 100GbE 포트 26를 상단 스위치(2)의 100GbE 포트 26에 연결합니다. 노트: S5248-ON 스위치를 사용하는 경우 포트 49-54를 사용해야 합니다.
Core uplinks Uplink A 1 3 Uplink B 4 2 그림 7 . Dell EMC PowerSwitch Serires S4148-ON ToR 스위치를 코어 업링크에 연결 표 15. Dell EMC PowerSwitch Serires S4148-ON ToR 스위치를 코어 업링크에 연결하는 단계 1 하단 ToR 스위치의 포트 30을 코어 업링크 A에 연결합니다. 2 하단 ToR 스위치의 포트 29를 코어 업링크 B에 연결합니다. 3 상단 ToR 스위치의 포트 29를 코어 업링크 A에 연결합니다. 4 상단 ToR 스위치의 포트 30을 코어 업링크 B에 연결합니다. 노트: 네트워크 관리자와 상의하여 ToR 스위치가 연결될 업링크 포트를 결정합니다.
6 스위치 및 네트워크 구성 검증 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • ToR(Top-of-Rack) 스위치의 구성 검증 PowerStore용 네트워크 유효성 검사 도구 ToR(Top-of-Rack) 스위치의 구성 검증 Dell EMC PowerSwitch Series S4148-ON ToR 스위치를 구성하고 케이블로 연결했으면 PowerStore X 모델 모델 배포를 검색하기 전에 구성을 검증합니다. 1. 스위치에 터미널 세션을 수립합니다. 2. 인터페이스 상태를 검증합니다. show interface status | grep up Port Eth 1/1/1 Eth 1/1/13 Eth 1/1/25 Eth 1/1/26 Eth 1/1/29 Eth 1/1/30 Eth 1/1/54 Description Node-A-Port-0 discoveryWork..
4094 T Po30 T Po1000 Inactive 5.
VLT VLAN mismatch: No mismatch 9. VLT 포트 구성을 검증합니다. show vlt vlt-port-detail vlt-port-channel ID : 30 VLT Unit ID Port-Channel Status Configured ports Active ports ------------------------------------------------------------------------------1 port-channel30 up 2 2 * 2 port-channel30 up 2 2 10. ToR 스위치 1의 실행 구성을 검토하고 ToR 스위치 2에 대한 모든 유효성 검사 단계를 반복합니다. show running-configuration 실행 구성의 출력에 대한 예시는 PowerStore X 모델: Dell EMC PowerSwitch Series S4148-On 스위치의 실행 구성을 참조 바랍니 다.
7 PowerStore 어플라이언스 검색 네트워크를 구성하고 어플라이언스 설치를 완료한 후에는 PowerStore 어플라이언스를 검색하여 초기 구성 프로세스를 시작할 수 있 습니다. 주제: • • 직접 연결을 사용하는 검색 원격 연결을 사용하는 검색 직접 연결을 사용하는 검색 이 권장 절차는 베이스 인클로저가 설치된 데이터 센터 또는 랩에서만 수행 가능합니다. ● (선택 사항) PowerStore 네트워크 유효성 검사 도구(NVT)를 다운로드하고 실행하여 네트워크가 올바르게 구성되어 있는지 검증 합니다. NVT는 Dell EMC Central Solutions(https://psapps.emc.com/central/solutions)에서 다운로드할 수 있습니다. ● 워크스테이션의 네트워크 어댑터가 다음과 같이 구성되어 있는지 확인합니다. ○ 노드 A의 PowerStore 서비스 포트에 직접 연결됩니다. ○ 게이트웨이 주소(128.221.1.249; 255.255.255.
Node Network B A 그림 9 . PowerStore X 모델 원격 검색 연결 다음과 같은 두 가지 검색 방법을 선택할 수 있습니다. ● 검색 툴을 사용하는 원격 검색 ● 정적 IP 주소를 사용하는 원격 검색 검색 툴을 사용하는 원격 검색 169.254.xx/16 IP 주소를 알리는 검색 툴을 사용하여 PowerStore를 검색할 수 있습니다. ● (선택 사항) PowerStore에 대한 네트워크 유효성 검사 도구(NVT)를 다운로드하고 실행하여 네트워크가 올바르게 구성되어 있는 지 확인합니다. NVT는 Dell EMC Central Solutions(https://psapps.emc.com/central/solution/NVT-PowerStore)에서 다운로드할 수 있습니다. ● 일시적으로 방화벽을 비활성화합니다. 이렇게 할 수 없는 경우 포트 5353 및 검색 유틸리티를 워크스테이션에서 실행되는 모든 방화벽 및 안티바이러스 소프트웨어의 제외 목록에 추가합니다.
지 않은 169.254.1.2로 설정합니다. 이 주소는 DHCP 또는 정적 IP 주소의 사용 여부와 상관없이 다른 주소 범위에서 덮어쓸 수 없습니다. 노트: 중복 IP 주소가 발생하지 않도록 하려면 설정하는 169.254.x.x IP 주소를 사용하는 동일한 기본/태그 미지정 네트워 크에 하나의 노트북 또는 가상 머신만 있어야 합니다. 1. 워크스테이션 또는 가상 머신에서 웹 브라우저를 열고 PowerStore 검색 유틸리티에 액세스하기 위해 예약된 IP 주소 중 하나를 입 력합니다. ● http://169.254.0.10 ● http://169.254.0.20 ● http://169.254.0.30 ● http://169.254.0.40 ● http://169.254.0.50 2. PowerStore Manager에 로그인하고 다음과 같은 기본 자격 증명을 사용하여 초기 구성 프로세스를 시작합니다.
8 PowerStore X 모델 어플라이언스의 초기 구성 이 챕터에서 다루는 내용은 다음과 같습니다. 주제: • • 초기 구성 마법사 작성된 초기 구성 워크시트 가져오기 초기 구성 마법사 PowerStore X 모델 어플라이언스를 검색한 후에는 Initial Configuration Wizard(ICW)로 리디렉션되어 PowerStore X 모델 어플라이 언스에 네트워크를 구성합니다. Initial Configuration Wizard(ICW)에는 PowerStore X 모델 어플라이언스의 초기 구성에 필요한 네트워크 정보를 입력하라는 메시지 가 표시됩니다. ICW를 통해 실행하는 동안에는 작성된 초기 구성 워크시트를 참조하십시오. 초기 구성 워크시트는 PowerStore X 모델 어플라이언스 의 초기 배포를 완료하는 데 필요한 모든 정보로 작성해야 합니다. ICW를 통해 실행하는 동안 다음 사항에 유의하십시오.
PowerStore X 모델 어플라이언스의 초기 구성을 완료한 후 추가 스토리지 네트워크 생성에 설명된 대로 스토리지 네트워크를 추가하 는 옵션을 사용할 수 있습니다. 작성된 초기 구성 워크시트 가져오기 Initial Configuration Wizard(ICW)에 PowerStore X 모델 어플라이언스의 초기 구성에 필요한 네트워크 정보를 입력하라는 메시지가 표시됩니다. 아래 워크시트에 제공된 네트워크 리소스가 PowerStore X 모델 네트워크를 구성 하는 단계에서 사용됩니다. 다음 워크시트는 Dell EMC PowerSwitch Series S4148-ON ToR(Top-of-Rack) 스위치에 구성된 리소스를 사용하여 작성되었습니다. 대 체 네트워크 리소스를 사용하여 환경을 구성하는 경우 초기 구성 워크시트에서 이 가이드에 나와 있는 빈 워크시트를 작성합니다. 또한 아래의 작성된 초기 구성 워크시트에서 클러스터에 대해 정의하는 관리자 암호를 기록해 두십시오.
표 16. 초기 구성 워크시트(작성 완료) (계속) 클러스터 IP 주소 192.168.1.10 관리 네트워크 DNS 및 NTP와 같은 서비스에 클러스터를 연결합니다. 관리 네트워크의 IP 주소는 클러스터, 어플라이언스, 컨트롤러 및 내부 호스 트를 처리하는 데 사용됩니다. VLAN (선택 사항, 기본값 0) 100 넷마스크/접두사 길 이 게이트웨이 255.255.255.0/2 4 192.168.1.1 IP 주소 각 PowerStore X 모델 어플라이언스 마다 IP 5개 192.168.1.11-15 스토리지 네트워크 클라이언트에서 클러스터의 스토리지에 액세스할 수 있도록 합니다. 스토리지 네트워크의 IP 주소는 iSCSI 타겟, iSCSI 이니시에이 터 및 글로벌 스토리지 검색 IP 주소에 사용됩니다. 적어도 각 PowerStore X 모델 어플라이언스에는 6개의 IP 주소가 필요합니다.
표 16. 초기 구성 워크시트(작성 완료) (계속) IP 주소 100.0.100.10 100.0.100.11 포트 포트 22 포트 22 SSH 사용자 이름 admin admin 스위치 암호 Password123! Password123! 하이퍼바이저 기존 vCenter 관리자 로그인 자격 증명을 기록합니다. 초기 구성 워크플로가 데이터 센터 및 ESXi 클러스터를 자동으로 생성하고 이 를 클러스터와 연결합니다. 노트: vCenter Server를 로컬 네트워크에서 사용할 수 있는지 확인합니다. vCenter 정보 vCenter Server IP 주소/호스트 이름 100.0.100.220 vCenter 관리자 사용자 이름 administrator@vsphere.
A 여러 포트에서 실행하도록 스토리지 네트워크 확 장 부록에는 다음과 같은 정보가 포함되어 있습니다. 주제: • 스토리지 네트워크 확장 스토리지 네트워크 확장 PowerStore X 모델 어플라이언스의 여러 포트에서 실행하도록 스토리지 네트워크를 확장할 수 있습니다. 스토리지 네트워크를 확장하는 단계를 수행하려면 다음 정보가 필요합니다. 노트: 아래의 샘플 네트워크 리소스는 이 가이드의 이전 챕터에서 2개의 Dell EMC PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 구성된 스토리지 네트워크를 확장하는 데 사용할 수 있습니다. 자세한 내용은 Dell EMC PowerSwitch Series S4148-ON 스위치를 사용한 구성을 참조하십시오. 이 가이드에 설명된 것과 동일한 스토리지 네트워크를 구성하지 않은 경우 샘플 리소스 를 해당 환경에 맞는 값으로 교체합니다. 표 17.
표 18. PowerStore X 모델 어플라이언스 이더넷 포트를 가상 포트에 매핑 (계속) 4포트 카드의 이더넷 포트 가상 포트 vSphere 포트 그룹 업링크 포트 1 vFEPort1 PG_Storage_TGT1 업링크 1 포트 2 vFEPort6 PG_Storage_TGT4 업링크 4 포트 3 vFEPort3 PG_Storage_TGT3 업링크 3 PowerStore X 모델 어플라이언스에서 구성한 추가 포트를 구성하고 스토리지 네트워크를 확장하려면 다음 단계를 수행합니다. 1. 스토리지 네트워크 확장을 위해 노드를 스위치에 케이블로 연결합니다. 2. ToR(Top-of-Rack) 스위치에서 VLAN을 구성합니다. 3. 가상 포트에 IP 주소를 추가하고 스토리지 네트워크를 매핑합니다.
ToR 스위치에서 VLAN 구성 다음 단계에서는 2개의 Dell PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 VLAN을 구성하는 예시를 제공합니다. 이러한 단계를 수행하기 전이나 후에 PowerStore X 모델 어플라이언스 노드를 스위치에 케이블로 연결할 수 있습니다. 자세한 단계 는 노드를 ToR 스위치에 케이블로 연결을 참조하십시오. 스토리지 네트워크가 생성된 VLAN을 사용하여 추가 ToR 스위치 포트를 이미 구성한 경우 이 단계를 건너뛸 수 있습니다. 다음 목록은 스토리지 네트워크 리소스를 참조하십시오. ● 스토리지 네트워크를 확장하는 데 필요한 네트워크 리소스 ● 다음 단계에서 사용되는 샘플 값 1. 첫 번째 ToR 스위치(Switch1)에 대해 터미널 연결을 수립합니다. 2. 글로벌 구성 모드를 시작합니다. configure terminal 3. ToR 스위치 1 포트 2를 통해 실행되도록 스토리지 네트워크 VLAN을 구성합니다.
10. Map Storage Network 페이지에서 확장할 스토리지 네트워크 옆에 있는 확인란을 선택하고 Map Network를 선택합니다. PowerStore Manager는 5단계에서 추가한 사용되지 않은 IP 주소를 자동으로 매핑합니다. 11. Map Storage Network 확인 대화 상자에서 Map Network를 다시 선택합니다. PowerStore Manager는 스토리지 네트워크를 선택한 가상 포트와 해당 가상 포트 모두에 자동으로 매핑합니다. 12. 스토리지 네트워크가 성공적으로 구성되었는지 검증하려면 다음을 수행합니다. a. Virtual 탭의 Name 열에서 스토리지 네트워크를 확장한 포트를 찾습니다. Link State는 녹색이어야 하고 스토리지 네트워크는 Mapped for Storage 열에 표시되어야 합니다. b.
B 추가 스토리지 네트워크 생성 이 부록에서 다루는 내용은 다음과 같습니다. 주제: • 새 스토리지 네트워크 생성 새 스토리지 네트워크 생성 4포트 카드의 포트마다 최대 8개의 네트워크를 사용하여 최대 32개의 스토리지 네트워크를 구성할 수 있습니다. 4포트 카드의 각 포트에 최대 8개의 네트워크를 구성할 수 있습니다. 새 스토리지 네트워크를 생성하는 단계를 수행하려면 다음 정보가 필요합니다. 노트: 아래의 샘플 네트워크 리소스는 Dell EMC PowerSwitch Series S4148-ON 스위치를 사용하여 구성에 설명된 대로 원래 스토 리지 네트워크에 구성된 2개의 Dell EMC PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 사용할 수 있습니다. 이 가이드에 설명된 것과 동일한 Dell EMC PowerSwitch Series S4148 ToR 스위치를 사용하지 않은 경우 샘플 리소스를 해당 환경에 맞는 값으 로 교체합니다. 표 20.
표 21. PowerStore X 모델 어플라이언스 이더넷 포트를 가상 포트에 매핑 4포트 카드의 이더넷 포트 가상 포트 vSphere 포트 그룹 업링크 포트 0 vFEPort2 PG_Storage_TGT2 업링크 2 포트 1 vFEPort1 PG_Storage_TGT1 업링크 1 포트 2 vFEPort6 PG_Storage_TGT4 업링크 4 포트 3 vFEPort3 PG_Storage_TGT3 업링크 3 PowerStore X 모델 어플라이언스에서 새 스토리지 네트워크를 생성할 추가 포트를 구성하려면 다음 단계를 수행합니다. 1. 노드를 ToR 스위치에 케이블로 연결합니다. 2. ToR 스위치에서 스토리지 네트워크를 구성합니다. 3. PowerStore Manager에서 추가 스토리지 네트워크를 생성합니다.
ToR 스위치에서 스토리지 네트워크 구성 다음 단계에서는 2개의 Dell PowerSwitch Series S4148 ToR(Top-of-Rack) 스위치에 스토리지 네트워크를 구성하는 예시를 제공합니 다. 이러한 단계를 수행하기 전이나 후에 PowerStore T 모델 어플라이언스 노드를 스위치에 케이블로 연결할 수 있습니다. 자세한 단계 는 노드를 ToR 스위치에 케이블로 연결을 참조하십시오. 다음 목록은 새 스토리지 네트워크 리소스를 참조하십시오. ● 새 스토리지 네트워크를 추가하는 데 필요한 네트워크 리소스 ● 다음 단계에서 사용되는 샘플 값 1. 첫 번째 ToR 스위치(Switch1)에 대해 터미널 연결을 수립합니다. 2. 글로벌 구성 모드를 시작합니다. configure terminal 3. ToR 스위치 1에서 스토리지 네트워크를 구성합니다. interface vlan 210 description Storage_Network2 exit 4.
a. Hardware 페이지로 이동합니다. b. 어플라이언스 이름을 선택하고 Ports 페이지로 이동하여 Virtual 탭을 선택합니다. c. Virtual 탭의 Name 열에서 스토리지 네트워크를 확장한 포트를 찾습니다. Link State는 녹색이어야 하고 스토리지 네트워크는 Mapped for Storage 열에 표시되어야 합니다. d. Virtual 탭에서 해당 포트를 찾아 Link State가 녹색인지 확인하고 스토리지 네트워크가 Mapped for Storage 열에 나타나는 지 확인합니다.
C 기타 Dell EMC PowerSwitch Series S4148-ON 스위치 구성 작업 이 부록에서 다루는 내용은 다음과 같습니다. 주제: 스위치를 공장 출하 설정으로 재설정 Dell EMC PowerSwitch Series S4148-ON ToR 스위치의 실행 구성 • • 스위치를 공장 출하 설정으로 재설정 필요한 경우 Dell EMC PowerSwitch Series S4148-ON 스위치를 출하 시 기본 설정으로 재설정할 수 있습니다. 노트: 스위치를 재설정하면 모든 기존 구성이 손실되며 스위치를 사용 중인 경우라면 트래픽이 중단됩니다. Dell EMC PowerSwitch Series S4148-ON 스위치가 출하 시 기본 설정으로 재설정된 경우 ● ● ● ● 텔넷 비활성화 SSH 활성화 DHCP 활성화 기본값 스위치 사용자 이름과 암호는 모두 admin입니다. 노트: Dell은 처음 로그인 시 관리자 암호를 변경하는 것을 권장합니다.
표 23. ToR 스위치의 실행 구성 예시 Switch1 interface breakout 1/1/30 map 100g-1x username admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5w jF8nnLD7/VKx8SloIhp4NoGZs0I/ UNwh8WVuxwfd9q4pWIgNs5BKH. role sysadmin ntp server 100.0.10.
표 23.
표 23.
표 23.
표 23.
표 23.