Dell EMC PowerStore Installations- und Servicehandbuch für die Modelle PowerStore 1000, 3000, 5000, 7000 und 9000 Version 2.x Juni 2021 Rev.
Hinweise, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS warnt vor möglichen Beschädigungen der Hardware oder vor Datenverlust und zeigt, wie diese vermieden werden können. WARNUNG: Mit WARNUNG wird auf eine potenziell gefährliche Situation hingewiesen, die zu Sachschäden, Verletzungen oder zum Tod führen kann. © 2020 - 2021 Dell Inc. oder ihre Tochtergesellschaften.
Inhaltsverzeichnis Weitere Ressourcen........................................................................................................................ 8 Kapitel 1: Installieren eines neuen Basisgehäuses und eines optionalen Erweiterungsgehäuses.............. 9 Installieren eines neuen s Basisgehäuse..............................................................................................................................9 Auswählen der Einbauposition für das Basisgehäuse............................
Entfernen eines Laufwerkfüllmoduls........................................................................................................................... 30 Einbauen eines 2,5-Zoll-Laufwerks.............................................................................................................................. 31 Überprüfen der Funktionsfähigkeit eines hinzugefügten Laufwerks...................................................................... 32 Austauschen eines Netzteils........................
Entfernen der Node.......................................................................................................................................................54 Entfernen der oberen Abdeckung von der Node...................................................................................................... 56 Entfernen des fehlerhaften Lüftermodul....................................................................................................................
Umsetzen von Teilen aus dem fehlerhaften Node in das Ersatz-Node................................................................. 88 Installieren Sie die obere Abdeckung auf der Node...................................................................................................88 Installieren des Node..................................................................................................................................................... 89 Hochfahren des Node...................................
Ausschalten eines PowerStore X-Modell-Node....................................................................................................... 115 Einschaltverfahren für PowerStore-Node.......................................................................................................................116 Einschalten eines PowerStore T-Modell-Node mit einem Serviceskript...............................................................
Vorwort Es werden regelmäßig neue Software- und Hardwareversionen veröffentlicht, um das Produkt kontinuierlich zu verbessern. Einige in diesem Dokument beschriebene Funktionen werden eventuell nicht von allen Versionen der von Ihnen derzeit verwendeten Software oder Hardware unterstützt. In den Versionshinweisen zum Produkt finden Sie aktuelle Informationen zu Produktfunktionen.
1 Installieren eines neuen Basisgehäuses und eines optionalen Erweiterungsgehäuses Führen Sie diese Verfahren aus, um ein neues Basisgehäuse und ein optionales Erweiterungsgehäuse für 25 Laufwerke zum System hinzuzufügen. Eine detaillierte Übersicht über diese Komponenten finden Sie im PowerStore – Hardwareinformationshandbuch. ANMERKUNG: Lesen Sie die Informationen in Sicherheitsvorkehrungen für den Umgang mit austauschbaren Einheiten auf Seite 109, bevor Sie Teile austauschen.
● ● ● ● ● Schienensatz für werkzeuglosen Einbau Netzkabel SAS-Kabel Kennzeichnungsblatt für SAS-Kabel Blende Installieren der Schienen im Schrank. Diese Aufgabe beschreibt das Verfahren für die Installation einer Schiene. Wiederholen Sie nach der Installation einer Schiene den Vorgang für die andere Schiene. Das Verfahren ist für die linke und rechte Schiene gleich. Sie können die Schienen entweder in ein Rack mit Vierkantlöchern oder in eines mit Rundlöchern einbauen. Schritte 1.
Abbildung 2. Installieren des Systems im Gehäuse Verbinden der Basisgehäuse-Appliance mit Switches Weitere Informationen zum Anschluss an die Switches finden Sie im PowerStore-Netzwerkleitfaden für PowerStore T-Modelle oder PowerStore-Netzwerkleitfaden für PowerStore X-Modelle. ANMERKUNG: Schließen Sie die Netzkabel erst an, wenn Sie die Netzwerkkonfiguration abgeschlossen haben.
2. Verbinden Sie das andere Ende des Netzkabels mit der Stromverteilereinheit (PDU) im Rack. Abbildung 4. Verbinden mit der PDU Nach dem Anschließen der Netzkabel startet das Basisgehäuse automatisch. Ermitteln Ihres Systems Nachdem Sie die Installation Ihres Basisgehäuses und der optionalen Erweiterungsgehäuse abgeschlossen haben, können Sie eine Erkennung für das neu installierte Gehäuse durchführen.
9. Wenn Sie das erste Erweiterungsgehäuse in einem laufenden System installieren, schließen Sie die Netzkabel und dann die Erweiterungskabel (Back-End) an. Überprüfen des Lieferumfangs Überprüfen Sie, ob Sie alle erforderlichen Teile für den Einbau des neuen Erweiterungsgehäuses mit 25 Laufwerken erhalten haben.
Entfernen einer Füllblende Info über diese Aufgabe In den meisten Fällen ist der Platz, in den Sie Ihr Gehäuse einbauen, durch eine Blende abgedeckt, die an Halterungen befestigt ist. Wenn eine oder mehrere Füllblenden den Bereich verdecken, in dem Sie das Gehäuse einbauen möchten, entfernen Sie die einzelnen Füllblenden. Gehen Sie dazu wie folgt vor. Schritte 1. Entfernen Sie die Füllblenden. 2.
Abbildung 6. Einbauen der Schienen 5. Wiederholen Sie den Vorgang für die andere Schiene. Installieren des Erweiterungsgehäuses auf den Schienen Schritte 1. Heben Sie das Erweiterungsgehäuse mit Unterstützung einer zweiten Person an und schieben Sie das Erweiterungsgehäuse von der Vorderseite des Racks aus in die Schienen. 2. Drücken Sie das Erweiterungsgehäuse in das Rack, bis die Schnappverschlüsse einrasten und das System im Rack verriegelt ist. Abbildung 7. Befestigen des Systems im Rack 3.
Installieren von Laufwerken Wenn die Laufwerke und das Gehäuse separat geliefert wurden, bauen Sie sie jetzt in das Gehäuse ein. Wenn die Laufwerke bereits im Gehäuse eingebaut sind, können Sie nun die Blende montieren. Einbauen eines Laufwerks Info über diese Aufgabe ANMERKUNG: Wenn Sie mehrere Laufwerke in einem hochgefahrenen System einbauen, warten Sie mindestens 10 Sekunden, bevor Sie das nächste Laufwerk einsetzen. Schritte 1. Richten Sie das Laufwerk an den Führungen im Steckplatz aus. 2.
CL5262 Abbildung 9. Installieren der Frontverkleidung Verkabeln des Basisgehäuses mit dem Erweiterungsgehäuse Befolgen Sie diese Richtlinien, um ein Basisgehäuse mit einem Erweiterungsgehäuse zu verkabeln. Voraussetzungen ANMERKUNG: Wenn Sie das erste Erweiterungsgehäuse in einem laufenden System installieren, verbinden Sie die Netzkabel mit dem Erweiterungsgehäuse, bevor Sie diese Schritte ausführen.
Expansion enclosure 0 B A Node B A Abbildung 10. Basisgehäuse mit einem Erweiterungsgehäuse verkabeln ANMERKUNG: Weitere Verkabelungsdiagramme finden Sie im Arbeitsblatt zur Kabeletikettierung. Anschließen der Erweiterungsgehäuse-Netzkabel Schritte 1. Verbinden Sie das Netzkabel mit dem Netz-/Kühlungsmodul: Abbildung 11. Anschließen des Netzkabels 2. Bringen Sie den Sicherheitsbügel (Zugentlastung) jeweils am Ausgangspunkt des Netzkabels an.
Hinzufügen eines Erweiterungsgehäuse mit 25 Laufwerken Führen Sie die folgenden Schritte aus, um ein Erweiterungsgehäuse mit 25 Laufwerken zu einem laufenden System mit einem vorhandenen Erweiterungsgehäuse mit 25 Laufwerken hinzuzufügen. ANMERKUNG: Wenn dies das erste Erweiterungsgehäuse ist, finden Sie weitere Informationen unter Einbauen eines Erweiterungsgehäuses mit 25 Laufwerken.
Komponente Menge Netzkabel (2), 2 schwarz und grau C13/C14 schwarz und grau C13/C20 Blende für Erweiterungsgehäuse (mit Schlüssel) 1 Mini-SAS-HD-Kabel (1-moder 2-m-Kupferkabel) zum Verbinden des letzten Erweiterungsgehäuse mit dem Node 2 Auswahl der Einbauposition für das Erweiterungsgehäuse Bevor Sie das neue Erweiterungsgehäuse einbauen, müssen Sie die Position des neuen Erweiterungsgehäuses im Rack festlegen. Schritte 1.
CL4064 Abbildung 12. Lösen einer Halterung Installieren der Schienen im Schrank. Diese Aufgabe beschreibt das Verfahren für die Installation einer Schiene. Wiederholen Sie nach der Installation einer Schiene den Vorgang für die andere Schiene. Das Verfahren ist für die linke und rechte Schiene gleich. Sie können die Schienen entweder in ein Rack mit Vierkantlöchern oder in eines mit Rundlöchern einbauen. Schritte 1.
Installieren des Erweiterungsgehäuses auf den Schienen Schritte 1. Heben Sie das Erweiterungsgehäuse mit Unterstützung einer zweiten Person an und schieben Sie das Erweiterungsgehäuse von der Vorderseite des Racks aus in die Schienen. 2. Drücken Sie das Erweiterungsgehäuse in das Rack, bis die Schnappverschlüsse einrasten und das System im Rack verriegelt ist. Abbildung 14. Befestigen des Systems im Rack 3.
Abbildung 15. Einbauen eines Laufwerks Die Aktivitätsleuchte blinkt, um darauf hinzuweisen, dass die Spin-Up-Sequenz begonnen hat. Installieren der Frontverkleidung Voraussetzungen VORSICHT: Wenn auf der Vorderseite der Blende eine Schutzfolie vorhanden ist, muss sie entfernt werden, bevor Sie das System in Betrieb nehmen. Andernfalls wird das System überhitzt.
Anschließen der Erweiterungsgehäuse-Netzkabel Schritte 1. Verbinden Sie das Netzkabel mit dem Netz-/Kühlungsmodul: Abbildung 17. Anschließen des Netzkabels 2. Bringen Sie den Sicherheitsbügel (Zugentlastung) jeweils am Ausgangspunkt des Netzkabels an. Die Zugentlastung verhindert, dass das Netzkabel aus dem Stromanschluss gezogen werden kann.
Expansion enclosure 1 B A Expansion enclosure 0 B A Node B A Abbildung 18.
Expansion enclosure 2 Expansion enclosure 1 Expansion enclosure 0 Node B A B A B A B A Abbildung 19. Basisgehäuse mit drei Erweiterungsgehäuse verkabeln ANMERKUNG: Weitere Verkabelungsdiagramme finden Sie im Arbeitsblatt zur Kabeletikettierung.
2 Wartungsverfahren für Basisgehäuse Das Basisgehäuse enthält vom Kunden austauschbare Komponenten. Führen Sie diese Verfahren aus, um eine fehlerhafte Komponente sicher auszutauschen. ANMERKUNG: Lesen Sie vor dem Umgang mit austauschbaren Teilen die Informationen unter Sicherheitsvorkehrungen für den Umgang mit austauschbaren Einheiten auf Seite 109.
Abbildung 20. Die Abdeckung nach oben drücken 3. Drücken Sie die orangefarbene Taste herunter, um die Verriegelung zu lösen. 4. Entfernen Sie das Laufwerk aus dem Steckplatz. Abbildung 21. Entfernen eines 2,5-Zoll-Laufwerks 5. Legen Sie das Laufwerk auf eine antistatische Oberfläche. Einbauen eines 2,5-Zoll-Laufwerks Info über diese Aufgabe ANMERKUNG: Wenn Sie mehrere Laufwerke in einem hochgefahrenen System einbauen, warten Sie mindestens 10 Sekunden, bevor Sie das nächste Laufwerk einsetzen. Schritte 1.
Abbildung 22. Einbauen eines 2,5-Zoll-Laufwerks 5. Wenn Sie ein NVMe-NVRAM-Laufwerk installieren, drücken Sie die Abdeckung in die richtige Position. Die Aktivitätsleuchte blinkt, um darauf hinzuweisen, dass die Spin-Up-Sequenz begonnen hat. Überprüfen der Funktionsfähigkeit eines Ersatzlaufwerks Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das fehlerhafte Laufwerk ersetzt haben. 3.
Schritte 1. Verpacken Sie das defekte Teil im Versandkarton des Ersatzteils. 2. Senden Sie das fehlerhafte Teil wie in den dem Ersatzteil beigefügten Anweisungen beschrieben an Ihren Serviceprovider zurück. 3. Weitere Informationen zum Zurücksenden von Teilen, die kundenseitig ausgetauscht werden können: a. b. c. d. e. Öffnen Sie PowerStore Manager. Klicken Sie oben rechts im Bildschirm auf Settings. Klicken Sie auf General Support. Klicken Sie unter Drives, Power Supplies, and Other Parts auf Return Part.
Abbildung 23. Entfernen eines Laufwerkfüllmoduls Einbauen eines 2,5-Zoll-Laufwerks Info über diese Aufgabe ANMERKUNG: Wenn Sie mehrere Laufwerke in einem hochgefahrenen System einbauen, warten Sie mindestens 10 Sekunden, bevor Sie das nächste Laufwerk einsetzen. Schritte 1. Richten Sie das Laufwerk an den Führungen im Steckplatz aus. 2. Schieben Sie das Laufwerk bei vollständig geöffneter Verriegelung vorsichtig in den Steckplatz. Wenn es das Gehäuse berührt, dreht sich die Verriegelung nach unten. 3.
Abbildung 24. Einbauen eines 2,5-Zoll-Laufwerks 5. Wenn Sie ein NVMe-NVRAM-Laufwerk installieren, drücken Sie die Abdeckung in die richtige Position. Die Aktivitätsleuchte blinkt, um darauf hinzuweisen, dass die Spin-Up-Sequenz begonnen hat. Überprüfen der Funktionsfähigkeit eines hinzugefügten Laufwerks Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das Laufwerk hinzugefügt haben. 3.
Identifizieren eines fehlerhaften Netzteils über PowerStore Manager Bevor Sie ein Netzteil ersetzen, vergewissern Sie sich, dass Sie dessen Position im System identifiziert haben. Mithilfe von PowerStore Manager können Sie ein fehlerhaftes Netzteil identifizieren und suchen. Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, die das Netzteil enthält, das Sie ersetzen möchten. 3.
Abbildung 26. Entfernen des Netzkabels 2. Drücken Sie die orangefarbene Entriegelung nach links (nach rechts für das untere Netzteil), halten Sie sie in dieser Position und greifen Sie den Griff des Netzteils. Ziehen Sie das Netzteil aus der Node heraus. Abbildung 27. Entfernen eines Netzteils Einbauen eines Netzteils Info über diese Aufgabe Die Netzteile sind in der oberen und unteren Node eingebaut, wobei das obere Netzteil verkehrt herum positioniert ist. Dieses Verfahren gilt für beide Netzteile.
0 1 1 3 XXX XXX XXXX XX REV:XXX 2 Abbildung 28. Einbauen eines Netzteils 3. Schließen Sie das Netzkabel an das Netzteil an und sichern Sie das Kabel mit dem Sicherheitsbügel am Stecker. Abbildung 29. Anschließen des Netzkabels Prüfen der Funktion eines Ersatznetzteils Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das Netzteil ersetzt haben. 3. Erweitern Sie auf der Karte Components unter Rear View die Option BaseEnclosure. 4.
Schritte 1. Verpacken Sie das defekte Teil im Versandkarton des Ersatzteils. 2. Senden Sie das fehlerhafte Teil wie in den dem Ersatzteil beigefügten Anweisungen beschrieben an Ihren Serviceprovider zurück. 3. Weitere Informationen zum Zurücksenden von Teilen, die kundenseitig ausgetauscht werden können: a. b. c. d. e. Öffnen Sie PowerStore Manager. Klicken Sie oben rechts im Bildschirm auf Settings. Klicken Sie auf General Support. Klicken Sie unter Drives, Power Supplies, and Other Parts auf Return Part.
Tabelle 2. Integriertes Modul-LEDs (fortgesetzt) LED Position Ethernetportaktivität SAS-Port und Aktivitätslink Portverbindung Node-Fehler Node-Strom Ausbau unsicher Bundesstaat/-land Beschreibung Gelb blinkend Portaktivität. Aus Keine Portaktivität. Blau Verbindung mit SAS-Port hergestellt. Aus Keine Verbindung hergestellt. Grün Hochgeschwindigkeitsverbindung hergestellt. Gelb Verbindung mit niedriger Geschwindigkeit hergestellt. Aus Verbindung unterbrochen.
Abbildung 31. Lösen des Hebels am integriertes Modul 3. Ziehen Sie den Entriegelungshebel vom System weg. Das integriertes Modul wird vom System gelöst, wenn Sie den Hebel ziehen. Abbildung 32. Entfernen des integriertes Moduls vom System 4. Entfernen Sie das integriertes Modul aus dem Steckplatz. Übertragen der Karte mit 4 Ports Wenn Sie die integriertes Modul austauschen, entfernen Sie die Karte mit 4 Ports aus dem alten integriertes Modul und installieren Sie sie in dem neuen integriertes Modul.
Entfernen eines Karte mit 4 Ports Schritte 1. Entfernen Sie die SFPs von der Vorderseite des integriertes Moduls. 2. Entfernen Sie beide Belüftungsblenden an der Vorderseite des integriertes Modul, indem Sie die unverlierbaren Schrauben lösen. 3. Drücken Sie die beiden blauen Laschen auf der Rückseite der Karte mit 4 Ports herunter, um die Karte mit 4 Ports zu lösen. Abbildung 33. Öffnen der Halterungen 4.
Abbildung 35. Einsetzen der Karte mit 4 Ports 3. Drücken Sie vorsichtig auf den Kreis oben links auf der Karte mit 4 Ports. 4. Drücken Sie die blauen Laschen nach oben, bis sie einrasten. Abbildung 36. Einrasten der Karte mit 4 Ports 5. Tauschen Sie beide Belüftungsblende aus, und ziehen Sie die unverlierbaren Schrauben fest. 6. Installieren Sie die SFPs im integriertes Modul. Installieren eines integriertes Moduls Schritte 1.
Abbildung 37. Installieren des integriertes Moduls 2. Wenn das integriertes Modul vollständig eingesetzt ist, drücken Sie den Entriegelungshebel zurück in das System, bis die orangefarbene Lasche den Hebel verriegelt. Abbildung 38. Verriegeln des Entriegelungshebels 3. Verbinden Sie jedes Kabel mit dem Port, von dem es entfernt wurde. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben. Überprüfen der Funktionsfähigkeit eines Ersatz-integriertes Modul Schritte 1.
Zurücksenden eines fehlerhaften Teils Info über diese Aufgabe Kunden in den USA müssen fehlerhafte Teile innerhalb von fünf Werktagen zurücksenden. Kunden außerhalb der USA müssen fehlerhafte Teile innerhalb von 10 Werktagen zurücksenden. Die für die Rücksendung des defekten Teils erforderlichen Materialien sind im Lieferumfang enthalten. Schritte 1. Verpacken Sie das defekte Teil im Versandkarton des Ersatzteils. 2.
Abbildung 39. Integriertes Modul-LEDs Tabelle 3. Integriertes Modul-LEDs LED Integriertes Modul-Strom Ethernetportverbindung Ethernetportaktivität SAS-Port und Aktivitätslink Portverbindung Node-Fehler Node-Strom Ausbau unsicher Position Bundesstaat/-land Beschreibung Gelb Integriertes Modul ist defekt. Aus Kein Fehler aufgetreten, Normalbetrieb. Grün Verbindung hergestellt. Aus Keine Verbindung hergestellt. Gelb blinkend Portaktivität. Aus Keine Portaktivität.
Tabelle 3. Integriertes Modul-LEDs (fortgesetzt) LED Position Bundesstaat/-land Beschreibung Aus Der integriertes Modul kann sicher entfernt werden, wenn der integriertes Modul ordnungsgemäß vorbereitet wurde. Ausschalten des Nodes Schalten Sie das Node aus, wie unter Ein-/Ausschaltverfahren beschrieben. Entfernen eines integriertes Moduls Schritte 1. Beschriften und trennen Sie alle Kabel, die mit dem integriertes Modul verbunden sind. VORSICHT: Ziehen Sie den Node nicht vom Basisgehäuse ab.
Abbildung 41. Entfernen des integriertes Moduls vom System 4. Entfernen Sie das integriertes Modul aus dem Steckplatz. Entfernen eines Karte mit 4 Ports Schritte 1. Entfernen Sie die SFPs von der Vorderseite des integriertes Moduls. 2. Drücken Sie die beiden blauen Laschen auf der Rückseite der Karte mit 4 Ports herunter, um die Karte mit 4 Ports zu lösen. Abbildung 42. Öffnen der Halterungen 3.
Abbildung 43. Entfernen der Karte mit 4 Ports Installieren einer Karte mit 4 Ports Schritte 1. Richten Sie die Karte mit 4 Ports im integriertes Modul so aus, dass die Ports an der Vorderseite mit den Steckplätzen an der Vorderseite des integriertes Moduls auf einer Linie sind. 2. Richten Sie die weißen Stifte unter den Löchern der Karte mit 4 Ports aus. VORSICHT: Erzwingen Sie das Einrasten der Karte mit 4 Ports nicht.
Abbildung 45. Einrasten der Karte mit 4 Ports 5. Ziehen Sie gegebenenfalls die vier unverlierbaren Schrauben fest, mit denen die Belüftungsblende an der Vorderseite des integriertes Moduls befestigt ist. 6. Installieren Sie die SFPs im integriertes Modul. Installieren eines integriertes Moduls Schritte 1. Richten Sie das integriertes Modul an dem leeren Steckplatz aus und drücken Sie es vorsichtig in den Steckplatz.
Abbildung 47. Verriegeln des Entriegelungshebels 3. Verbinden Sie jedes Kabel mit dem Port, von dem es entfernt wurde. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben. Überprüfen der Funktionsfähigkeit einer neuen Karte mit 4 Ports Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das Karte mit 4 Ports ersetzt haben. 3. Erweitern Sie auf der Karte Components unter Rear View die Option BaseEnclosure.
Austauschen eines SFP Gehen Sie wie folgt vor, um das fehlerhafte SFP zu entfernen und das als Ersatz dienende SFP im System einzubauen. Identifizieren eines fehlerhaften SFP-Moduls über PowerStore Manager Mithilfe von PowerStore Manager können Sie ein fehlerhaftes SFP-Modul identifizieren und suchen. Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, die das SFP-Modul enthält, das Sie ersetzen möchten. 3.
2. Drücken Sie die gefederte Verriegelung nach oben und schieben Sie das neue SFP-Modul in den Port, bis dieses sicher angeschlossen ist. EMC3550 Abbildung 49. Installieren eines SFP-Moduls 3. Drücken Sie die gefederte Verriegelung nach unten, um das SFP Modul einzurasten. 4. Schließen Sie das Kabel am Ersatz-SFP-Modul wieder an. Beispiel Überprüfen der Funktionsfähigkeit eines Ersatz-SFP-Moduls Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2.
Austauschen einer I/O-Modul Gehen Sie wie folgt vor, um das fehlerhafte I/O-Modul zu entfernen und das als Ersatz dienende I/O-Modul im System einzubauen. Identifizieren eines fehlerhaften I/O-Modul über PowerStore Manager Bevor Sie ein I/O-Modulersetzen, vergewissern Sie sich, dass Sie dessen Position im System identifiziert haben. Mithilfe von PowerStore Manager können Sie ein fehlerhaftes I/O-Modul identifizieren und suchen. Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2.
Entfernen eines fehlerhaften I/O-Modul Schritte 1. Ziehen Sie den Lösemechanismus am Griff des I/O-Modul, um es zu lösen. VORSICHT: Ziehen Sie den Node nicht vom Basisgehäuse ab. Durch Abziehen des Node vom Basisgehäuse wird der Systemcache unterbrochen. Abbildung 51. Lösen des I/O-Moduls 2. Ziehen Sie das I/O-Modul vorsichtig aus dem Steckplatz heraus. Abbildung 52. Entfernen des I/O-Moduls Installieren eines neuen I/O-Modul Schritte 1.
● Bleibt der Knopf gedrückt, ist das Modul vollständig eingesetzt. ● Springt der Knopf zurück, drücken Sie das Modul vorsichtig weiter in den Rahmen. Drücken Sie den Knopf dann erneut. ● Schließt der Knopf weiterhin nicht bündig mit dem Griff ab, entfernen Sie das Modul und wiederholen Sie die Schritte 1 und 2. Abbildung 54. Sperren im I/O-Modul 3. Schließen Sie Kabel an die Ports des I/O-Moduls an. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben.
Ersetzen eines Lüftermodul Gehen Sie wie folgt vor, um das fehlerhafte Lüftermodul zu entfernen und das als Ersatz dienende Lüftermodul im System einzubauen. Identifizieren eines fehlerhaften Lüftermodul über PowerStore Manager Bevor Sie ein Lüftermodul ersetzen, vergewissern Sie sich, dass Sie dessen Position im System identifiziert haben. Mithilfe von PowerStore Manager können Sie ein fehlerhaftes Lüftermodul identifizieren und suchen. Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus.
Abbildung 55. Entfernen des Netzkabels 2. Trennen Sie die Netzwerkkabel und sämtliche anderen Kabel von der Rückseite der I/O-Module und den Netzwerkports am Node. ANMERKUNG: Ziehen Sie keine Kabel vom anderen Node ab. 3. Ziehen Sie den orangefarbenen Auslöser, während Sie vorsichtig auf den Node drücken. Der Haken löst sich aus dem Verriegelungsmechanismus und die Arretierlasche gleitet heraus. ANMERKUNG: Der Node wird vollständig aus dem Gehäuse ausgeworfen.
Abbildung 57. Entfernen des Nodes 6. Legen Sie den Node auf eine saubere, flache und antistatische Arbeitsfläche. Entfernen der oberen Abdeckung von der Node Schritte 1. Schieben Sie die obere Abdeckung nach hinten, während Sie die beiden blauen Entriegelungstasten nach unten drücken, bis sie stoppt. Abbildung 58. Lösen der oberen Abdeckung 2. Heben Sie die obere Abdeckung an und entfernen Sie sie vom Node.
Abbildung 59. Entfernen der oberen Abdeckung Entfernen des fehlerhaften Lüftermodul Schritte 1. Trennen Sie das Netzkabel des Lüftermoduls von der Hauptplatine. Abbildung 60. Trennen des Netzkabels des Lüfters 2. Lösen Sie das Netzkabel des Lüftermoduls vom Kabelhalter. 3. Drücken Sie die blauen Freigabelaschen. 4. Heben Sie das Lüftermodul von der Hauptplatine ab.
Abbildung 61. Entfernen des Lüfters von der Hauptplatine Installieren eines neuen Lüftermodul Schritte 1. Platzieren Sie das Lüftermodul in die Montageposition in der Node. 2. Drücken Sie die blauen Laschen zusammen und drücken Sie sie nach unten, um das Lüftermodul in Position zu verriegeln. 3. Verbinden Sie das Netzkabel des Lüftermoduls mit dem Anschluss auf der Hauptplatine. Abbildung 62. Installieren des Lüftermoduls Installieren Sie die obere Abdeckung auf der Node Schritte 1.
Abbildung 63. Ausrichten der oberen Abdeckung 2. Ziehen Sie die obere Abdeckung nach vorn, um sie zu sichern. Abbildung 64. Sichern der oberen Abdeckung Installieren des Node Schritte 1. Richten Sie die Pins auf der Oberseite der Node mit den Aussparungen auf der Oberseite des Chassis aus. 2. Schieben Sie die Node in das Gehäuse, bis sie etwa auf halbem Weg stoppt.
Abbildung 65. Schieben der Node zur Hälfte in das Gehäuse 3. Ziehen Sie die schwarze Freigabelasche vollständig heraus und schieben Sie den Rest der Node in das Gehäuse zurück. Die schwarze Freigabelasche gleitet wieder zurück in das System, während es eingesetzt wird. Abbildung 66. Installieren des Nodes 4. Ziehen Sie den orangefarbenen Entriegelungsauslöser und drücken Sie ihn vorsichtig, um den Verriegelungsmechanismus erneut zu aktivieren.
Der Status des Ersatz-Lüftermodul sollte Healthy lauten. Wenn der Status weiterhin Faulted lautet, warten Sie einige Minuten und aktualisieren Sie PowerStore Manager. Wenn sich der Status nicht ändert, vergewissern Sie sich, dass das Lüftermodul richtig eingesetzt ist, oder kontaktieren Sie Ihren Serviceanbieter. Zurücksenden eines fehlerhaften Teils Info über diese Aufgabe Kunden in den USA müssen fehlerhafte Teile innerhalb von fünf Werktagen zurücksenden.
Entfernen der Node In diesem Verfahren wird beschrieben, wie Sie einen Node aus dem Gehäuse entfernen. Es gibt zwei Nodes. Der obere Node ist mit der Oberseite nach unten eingesetzt und ist eine Spiegelung des unteren Node. Das Verfahren zum Entfernen des oberen Node und unteren Node ist identisch. Info über diese Aufgabe WARNUNG: Entfernen Sie den Node nicht innerhalb von fünf Minuten nach dem Herunterfahren des Systems, um sicherzustellen, dass das System ausreichend Zeit zum Abschließen des Caching hat.
Abbildung 68. Lösen des Verriegelungsmechanismus für Node B 4. Stellen Sie vor dem Entfernen des Node sicher, dass der Drahtbügel ordnungsgemäß am Netzkabel des anderen Node befestigt ist, um einen versehentlichen Verlust der Stromversorgung und des Cache zu verhindern. 5. Ziehen Sie den Node am Entriegelungsgriff so weit aus dem Gehäuse heraus, dass Sie die Seiten mit beiden Händen greifen können. Halten Sie den Node mit beiden Händen fest und ziehen Sie den Node dann vollständig aus dem Gehäuse heraus.
Abbildung 70. Lösen der oberen Abdeckung 2. Heben Sie die obere Abdeckung an und entfernen Sie sie vom Node. Abbildung 71. Entfernen der oberen Abdeckung Entfernen des fehlerhaften DIMM (Dual Inline Memory Module) Schritte 1. Suchen Sie das fehlerhafte DIMM wie unter Identifizieren eines fehlerhaften Teils über PowerStore Manager beschrieben. Suchen Sie das fehlerhafte DIMM im Node, indem Sie die Abbildung unten als Referenz für die Ausrichtung verwenden.
Abbildung 72. Draufsicht auf den Node ANMERKUNG: Ganz links ist DIMM-Steckplatz 23, und die Steckplätze verringern sich sequentiell bis zum Steckplatz 0 ganz rechts. 2. Drücken Sie die weißen oder schwarzen Halterungen nach unten, um das DIMM aus dem Steckplatz freizugeben. 3. Entfernen Sie das fehlerhafte DIMM. Abbildung 73. Entfernen des DIMM Einsetzen des DIMM (Dual Inline Memory Module) Schritte 1. Halten Sie das DIMM nur an den äußeren Seiten und richten Sie es am Anschluss aus. 2.
● Setzen Sie nicht zuerst ein Ende des DIMMs und dann das andere ein. Abbildung 74. Einsetzen des DIMM 3. Beim korrekten Einsetzen des DIMMs werden die Auswerfer der Verriegelung automatisch geschlossen und das DIMM im Sockel verriegelt. Vergewissern Sie sich, dass die Auswerferhebel vollständig geschlossen sind und in die Kerben des DIMMs eingreifen. Installieren Sie die obere Abdeckung auf der Node Schritte 1.
Abbildung 76. Sichern der oberen Abdeckung Installieren des Node Schritte 1. Richten Sie die Pins auf der Oberseite der Node mit den Aussparungen auf der Oberseite des Chassis aus. 2. Schieben Sie die Node in das Gehäuse, bis sie etwa auf halbem Weg stoppt. Abbildung 77. Schieben der Node zur Hälfte in das Gehäuse 3. Ziehen Sie die schwarze Freigabelasche vollständig heraus und schieben Sie den Rest der Node in das Gehäuse zurück.
Abbildung 78. Installieren des Nodes 4. Ziehen Sie den orangefarbenen Entriegelungsauslöser und drücken Sie ihn vorsichtig, um den Verriegelungsmechanismus erneut zu aktivieren. Wenn die schwarze Freigabelasche herauskommt, wenn gezogen wird, ist der Verriegelungsmechanismus nicht aktiviert. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben. Überprüfen der Funktionsfähigkeit eines Ersatz-DIMM Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2.
d. Klicken Sie unter Drives, Power Supplies, and Other Parts auf Return Part. e. Wenn der Link zum Zurücksenden von Teilen nicht auf dem Bildschirm angezeigt wird, wenden Sie sich an Ihren Serviceanbieter, um weitere Anweisungen zu erhalten. Austauschen eines Internes M.2-Boot-Modul Gehen Sie wie folgt vor, um das fehlerhafte Internes M.2-Boot-Modul zu entfernen und das als Ersatz dienende Internes M.2-Boot-Modul im System einzubauen. Das Internes M.2-Boot-Modul befindet sich im Node.
Abbildung 79. Entfernen des Netzkabels 2. Trennen Sie die Netzwerkkabel und sämtliche anderen Kabel von der Rückseite der I/O-Module und den Netzwerkports am Node. ANMERKUNG: Ziehen Sie keine Kabel vom anderen Node ab. 3. Ziehen Sie den orangefarbenen Auslöser, während Sie vorsichtig auf den Node drücken. Der Haken löst sich aus dem Verriegelungsmechanismus und die Arretierlasche gleitet heraus. ANMERKUNG: Der Node wird vollständig aus dem Gehäuse ausgeworfen.
Abbildung 81. Entfernen des Nodes 6. Legen Sie den Node auf eine saubere, flache und antistatische Arbeitsfläche. Entfernen der oberen Abdeckung von der Node Schritte 1. Schieben Sie die obere Abdeckung nach hinten, während Sie die beiden blauen Entriegelungstasten nach unten drücken, bis sie stoppt. Abbildung 82. Lösen der oberen Abdeckung 2. Heben Sie die obere Abdeckung an und entfernen Sie sie vom Node.
Abbildung 83. Entfernen der oberen Abdeckung Entfernen des fehlerhaften Internes M.2-Boot-Modul Schritte 1. Lokalisieren Sie das M.2-Boot-Modul-Adapter im Node. Sie können den M.2-Boot-Modul-Adapter anhand der blauen Laschen identifizieren. 2. Drücken Sie die blauen Laschen nach unten, um den M.2-Boot-Modul-Adapter aus dem Steckplatz zu lösen. 3. Berühren Sie nur die Außenkanten des M.2-Boot-Modul-Adapters und entfernen Sie den M.2-Boot-Modul-Adapter. Abbildung 84. Entfernen des M.2-Boot-Modul-Adapters 4.
Abbildung 85. Entfernen des Internes M.2-Boot-Moduls aus dem M.2-Boot-Modul-Adapter Installieren des Internes M.2-Boot-Modul Schritte 1. Platzieren Sie das Internes M.2-Boot-Modul in den M.2-Boot-Modul-Adapter. ANMERKUNG: Die Seite des Internes M.2-Boot-Moduls mit den Barcodes muss nach oben zeigen. 2. Richten Sie die blaue Lasche am Ersatz-Internes M.2-Boot-Modul mit dem Steckplatz am M.2-Boot-Modul-Adapter aus und schieben Sie sie vorsichtig in Position. 3.
Abbildung 87. Installieren des M.2-Boot-Modul-Adapters Installieren Sie die obere Abdeckung auf der Node Schritte 1. Positionieren Sie die obere Abdeckung über die Node und richten Sie sie an den seitlichen Aussparungen an der Rückseite der Node aus. Abbildung 88. Ausrichten der oberen Abdeckung 2. Ziehen Sie die obere Abdeckung nach vorn, um sie zu sichern.
Abbildung 89. Sichern der oberen Abdeckung Installieren des Node Schritte 1. Richten Sie die Pins auf der Oberseite der Node mit den Aussparungen auf der Oberseite des Chassis aus. 2. Schieben Sie die Node in das Gehäuse, bis sie etwa auf halbem Weg stoppt. Abbildung 90. Schieben der Node zur Hälfte in das Gehäuse 3. Ziehen Sie die schwarze Freigabelasche vollständig heraus und schieben Sie den Rest der Node in das Gehäuse zurück.
Abbildung 91. Installieren des Nodes 4. Ziehen Sie den orangefarbenen Entriegelungsauslöser und drücken Sie ihn vorsichtig, um den Verriegelungsmechanismus erneut zu aktivieren. Wenn die schwarze Freigabelasche herauskommt, wenn gezogen wird, ist der Verriegelungsmechanismus nicht aktiviert. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben. Überprüfen der Funktionsfähigkeit eines Ersatz-Internes M.2-BootModuls Schritte 1.
c. Klicken Sie auf General Support. d. Klicken Sie unter Drives, Power Supplies, and Other Parts auf Return Part. e. Wenn der Link zum Zurücksenden von Teilen nicht auf dem Bildschirm angezeigt wird, wenden Sie sich an Ihren Serviceanbieter, um weitere Anweisungen zu erhalten. Austauschen einer M.2-Boot-Modul-Adapter Gehen Sie wie folgt vor, um das fehlerhafte M.2-Boot-Modul-Adapter zu entfernen und das als Ersatz dienende M.2-Boot-Modul-Adapter im System einzubauen. Der M.
Abbildung 92. Entfernen des Netzkabels 2. Trennen Sie die Netzwerkkabel und sämtliche anderen Kabel von der Rückseite der I/O-Module und den Netzwerkports am Node. ANMERKUNG: Ziehen Sie keine Kabel vom anderen Node ab. 3. Ziehen Sie den orangefarbenen Auslöser, während Sie vorsichtig auf den Node drücken. Der Haken löst sich aus dem Verriegelungsmechanismus und die Arretierlasche gleitet heraus. ANMERKUNG: Der Node wird vollständig aus dem Gehäuse ausgeworfen.
Abbildung 94. Entfernen des Nodes 6. Legen Sie den Node auf eine saubere, flache und antistatische Arbeitsfläche. Entfernen der oberen Abdeckung von der Node Schritte 1. Schieben Sie die obere Abdeckung nach hinten, während Sie die beiden blauen Entriegelungstasten nach unten drücken, bis sie stoppt. Abbildung 95. Lösen der oberen Abdeckung 2. Heben Sie die obere Abdeckung an und entfernen Sie sie vom Node.
Abbildung 96. Entfernen der oberen Abdeckung Entfernen des fehlerhaften M.2-Boot-Modul-Adapter Schritte 1. Lokalisieren Sie das M.2-Boot-Modul-Adapter im Node. Sie können den M.2-Boot-Modul-Adapter anhand der blauen Laschen identifizieren. 2. Drücken Sie die blauen Laschen nach unten, um den M.2-Boot-Modul-Adapter aus dem Steckplatz zu lösen. 3. Berühren Sie nur die Außenkanten des M.2-Boot-Modul-Adapters und entfernen Sie den M.2-Boot-Modul-Adapter. Abbildung 97. Entfernen des M.2-Boot-Modul-Adapters 4.
Abbildung 98. Entfernen des Interne M.2-Boot-Modules aus dem M.2-Boot-Modul-Adapter Installieren des M.2-Boot-Modul-Adapter Schritte 1. Platzieren Sie die Interne M.2-Boot-Module, die Sie aus dem fehlerhaften M.2-Boot-Modul-Adapter entfernt haben, in das neue M.2-Boot-Modul-Adapter. ANMERKUNG: Die Seite des Internes M.2-Boot-Moduls mit den Barcodes muss nach oben zeigen. 2. Richten Sie die blaue Lasche am Ersatz-Internes M.2-Boot-Modul mit dem Steckplatz am M.
Abbildung 100. Installieren des M.2-Boot-Modul-Adapters Installieren Sie die obere Abdeckung auf der Node Schritte 1. Positionieren Sie die obere Abdeckung über die Node und richten Sie sie an den seitlichen Aussparungen an der Rückseite der Node aus. Abbildung 101. Ausrichten der oberen Abdeckung 2. Ziehen Sie die obere Abdeckung nach vorn, um sie zu sichern.
Abbildung 102. Sichern der oberen Abdeckung Installieren des Node Schritte 1. Richten Sie die Pins auf der Oberseite der Node mit den Aussparungen auf der Oberseite des Chassis aus. 2. Schieben Sie die Node in das Gehäuse, bis sie etwa auf halbem Weg stoppt. Abbildung 103. Schieben der Node zur Hälfte in das Gehäuse 3. Ziehen Sie die schwarze Freigabelasche vollständig heraus und schieben Sie den Rest der Node in das Gehäuse zurück.
Abbildung 104. Installieren des Nodes 4. Ziehen Sie den orangefarbenen Entriegelungsauslöser und drücken Sie ihn vorsichtig, um den Verriegelungsmechanismus erneut zu aktivieren. Wenn die schwarze Freigabelasche herauskommt, wenn gezogen wird, ist der Verriegelungsmechanismus nicht aktiviert. Hochfahren des Node Fahren Sie das Node hoch, wie unter Ein-/Ausschaltverfahren beschrieben. Überprüfen der Funktionsfähigkeit eines Ersatz-M.2-Boot-ModulAdapter Info über diese Aufgabe Der M.
2. Senden Sie das fehlerhafte Teil wie in den dem Ersatzteil beigefügten Anweisungen beschrieben an Ihren Serviceprovider zurück. 3. Weitere Informationen zum Zurücksenden von Teilen, die kundenseitig ausgetauscht werden können: a. b. c. d. e. Öffnen Sie PowerStore Manager. Klicken Sie oben rechts im Bildschirm auf Settings. Klicken Sie auf General Support. Klicken Sie unter Drives, Power Supplies, and Other Parts auf Return Part.
Abbildung 105. Entfernen des Netzkabels 2. Trennen Sie die Netzwerkkabel und sämtliche anderen Kabel von der Rückseite der I/O-Module und den Netzwerkports am Node. ANMERKUNG: Ziehen Sie keine Kabel vom anderen Node ab. 3. Ziehen Sie den orangefarbenen Auslöser, während Sie vorsichtig auf den Node drücken. Der Haken löst sich aus dem Verriegelungsmechanismus und die Arretierlasche gleitet heraus. ANMERKUNG: Der Node wird vollständig aus dem Gehäuse ausgeworfen.
Abbildung 107. Entfernen des Nodes 6. Legen Sie den Node auf eine saubere, flache und antistatische Arbeitsfläche. Entfernen der oberen Abdeckung von der Node Schritte 1. Schieben Sie die obere Abdeckung nach hinten, während Sie die beiden blauen Entriegelungstasten nach unten drücken, bis sie stoppt. Abbildung 108. Lösen der oberen Abdeckung 2. Heben Sie die obere Abdeckung an und entfernen Sie sie vom Node.
Abbildung 109. Entfernen der oberen Abdeckung Umsetzen von Teilen aus dem fehlerhaften Node in das Ersatz-Node Setzen Sie die folgenden Komponenten aus dem fehlerhaften Node an die entsprechenden Positionen im Ersatz-Node um: Um die korrekte Platzierung im Gehäuse zu gewährleisten, setzen Sie nur jeweils eine Komponente um. ANMERKUNG: Vergewissern Sie sich, dass alle Teile vollständig sitzen, bevor Sie den Node in das Basisgehäuse einsetzen.
Abbildung 110. Ausrichten der oberen Abdeckung 2. Ziehen Sie die obere Abdeckung nach vorn, um sie zu sichern. Abbildung 111. Sichern der oberen Abdeckung Installieren des Node Schritte 1. Richten Sie die Pins auf der Oberseite der Node mit den Aussparungen auf der Oberseite des Chassis aus. 2. Schieben Sie die Node in das Gehäuse, bis sie etwa auf halbem Weg stoppt.
Abbildung 112. Schieben der Node zur Hälfte in das Gehäuse 3. Ziehen Sie die schwarze Freigabelasche vollständig heraus und schieben Sie den Rest der Node in das Gehäuse zurück. Die schwarze Freigabelasche gleitet wieder zurück in das System, während es eingesetzt wird. Abbildung 113. Installieren des Nodes 4. Ziehen Sie den orangefarbenen Entriegelungsauslöser und drücken Sie ihn vorsichtig, um den Verriegelungsmechanismus erneut zu aktivieren.
Der Status der Ersatz-Node sollte Healthy lauten. Wenn der Status weiterhin Faulted lautet, warten Sie einige Minuten und aktualisieren Sie PowerStore Manager. Wenn sich der Status nicht ändert, vergewissern Sie sich, dass das Node richtig eingesetzt ist, oder kontaktieren Sie Ihren Serviceanbieter. Zurücksenden eines fehlerhaften Teils Info über diese Aufgabe Kunden in den USA müssen fehlerhafte Teile innerhalb von fünf Werktagen zurücksenden.
3 Erweiterungsgehäuse Serviceverfahren für Das Erweiterungsgehäuse enthält vom Kunden austauschbare Komponenten. Führen Sie diese Verfahren aus, um eine fehlerhafte Komponente sicher auszutauschen. ANMERKUNG: Lesen Sie vor dem Umgang mit austauschbaren Teilen die Informationen unter Sicherheitsvorkehrungen für den Umgang mit austauschbaren Einheiten auf Seite 109.
CL5261 Abbildung 114. Entfernen der Frontblende Entfernen eines Laufwerkfüllmoduls Schritte 1. Legen Sie einen Finger auf die Aussparung an der Unterseite des Laufwerkfüllmoduls (2). 2. Drücken Sie mit dem Daumen auf die Verriegelung auf der oberen Seite des Laufwerkfüllmoduls und ziehen Sie das Modul aus dem Steckplatz (2). 1 2 CL5219 Abbildung 115.
Schritte 1. Richten Sie das Laufwerk an den Führungen im Steckplatz aus. 2. Schieben Sie das Laufwerk bei vollständig geöffneter Verriegelung vorsichtig in den Steckplatz. Wenn es das Gehäuse berührt, dreht sich die Verriegelung nach unten. 3. Drücken Sie die orangefarbene Taste, bis das Laufwerk vollständig im Steckplatz sitzt. 4. Drücken Sie die Verriegelung nach unten, bis sie einrastet. Abbildung 116.
Überprüfen der Funktionsfähigkeit eines hinzugefügten Laufwerks Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das Laufwerk hinzugefügt haben. 3. Erweitern Sie auf der Karte Components unter Drives die Option ExpansionEnclosure, und wählen Sie das Laufwerk aus. Der Status des Laufwerks sollte Healthy lauten. Wenn der Status weiterhin Faulted lautet, warten Sie einige Minuten und aktualisieren Sie PowerStore Manager.
CL5261 Abbildung 118. Entfernen der Frontblende Entfernen eines fehlerhaften Laufwerks Schritte 1. Suchen Sie das Laufwerk mit der blinkenden gelben LED-Fehleranzeige. 2. Drücken Sie die orangefarbene Taste herunter, um die Verriegelung zu lösen. 3. Entfernen Sie das Laufwerk aus dem Steckplatz. Abbildung 119. Entfernen eines Laufwerks 4. Legen Sie das Laufwerk auf eine antistatische Oberfläche.
Schritte 1. Richten Sie das Laufwerk an den Führungen im Steckplatz aus. 2. Schieben Sie das Laufwerk bei vollständig geöffneter Verriegelung vorsichtig in den Steckplatz. Wenn es das Gehäuse berührt, dreht sich die Verriegelung nach unten. 3. Drücken Sie die orangefarbene Taste, bis das Laufwerk vollständig im Steckplatz sitzt. 4. Drücken Sie die Verriegelung nach unten, bis sie einrastet. Abbildung 120.
Überprüfen der Funktionsfähigkeit eines Ersatzlaufwerks Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das fehlerhafte Laufwerk ersetzt haben. 3. Erweitern Sie auf der Karte Components unter Drives die Option ExpansionEnclosure, und wählen Sie das Laufwerk aus. Der Status des Ersatzlaufwerks sollte Healthy lauten. Wenn der Status weiterhin Faulted lautet, warten Sie einige Minuten und aktualisieren Sie PowerStore Manager.
Entfernen einer fehlerhaften LCC Voraussetzungen Die fehlerhafte LCC (Link Control Card) erkennen Sie an der gelben Fehler-LED. # # CL5982 Abbildung 122. LCC-Fehler-LED Info über diese Aufgabe VORSICHT: Das DAE muss beim Hochfahren des Gehäuses mindestens über eine LCC verfügen. Entfernen Sie nicht beide LCCs, während der Netzstrom eingeschaltet ist. Schritte 1. Befestigen Sie ein ESD-Armband an Ihrem Handgelenk und am Gehäuse. 2.
CL5983 Abbildung 123. Entfernen eines LCC-Kabels 3. Nehmen Sie die LCC heraus: VORSICHT: Die LCC (Link Control Card) wird vollständig aus dem DAE-Gehäuse ausgeworfen. Seien Sie darauf vorbereitet, neben den Verriegelungen auch die LCC festzuhalten, damit sie nicht herunterfällt. a. Schauen Sie nach den orangefarbenen Grifftasten auf den LCC-Griffen. b. Drücken Sie auf die orangefarbenen Grifftasten, um die LCC zu entriegeln.
1 2 CL5984 Abbildung 124. Entfernen einer LCC 4. Legen Sie die LCC auf eine saubere, antistatische Oberfläche. Einbauen einer Ersatz-LCC Schritte 1. Befestigen Sie ein ESD-Armband an Ihrem Handgelenk und am Gehäuse. 2. Ziehen Sie die Verriegelungen an der LCC heraus und achten Sie darauf, dass sie in der geöffneten Position bleiben. 3. Richten Sie die LCC auf die Öffnung des Gehäuses aus und schieben Sie sie vorsichtig und gerade in das Gehäuse hinein.
1 2 CL5985 Abbildung 125. Einbauen einer LCC 4. Drücken Sie auf die Verriegelungen, um die LCC zu sichern. 5. Verbinden Sie jedes Kabel erneut mit dem Port, von dem es entfernt wurde. Ergebnisse Die LCC-Betriebs-LED leuchtet.
# # CL5986 Abbildung 126. LCC-Betriebs-LED Überprüfen der Funktionsfähigkeit eines Ersatz-LCC Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das LCC ersetzt haben. 3. Erweitern Sie auf der Karte Components unter Rear View die Option ExpansionEnclosure. 4. Wählen Sie das entsprechende LCCaus. Der Status des Ersatz-LCC sollte Healthy lauten.
Identifizieren eines fehlerhaften Netzteils/Lüfter-Ersatzmoduls über PowerStore Manager Bevor Sie ein Netzteil/Lüftermodul ersetzen, vergewissern Sie sich, dass Sie dessen Position im System identifiziert haben. Mithilfe von PowerStore Manager können Sie ein fehlerhaftes Netzteil/Lüftermodul identifizieren und suchen. Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, die das Netzteil/Lüftermodul enthält, das Sie ersetzen möchten. 3.
Abbildung 128. Trennen des Netzkabels vom Wechselstrom-Netzteil/Kühlungsmodul 3. Ziehen Sie für ein Netzteil/Kühlungsmodul (Gleichstrom) den Stecker an den Federverriegelungen auf jeder Seite des Netzkabelsteckers aus der Buchse. Gefederte Verriegelung CL5060 Abbildung 129. Trennen des Netzkabels von einem Gleichstrom-Netzteil/Kühlungsmodul 4. Bauen Sie das Netz-/Kühlungsmodul wie folgt aus: a. Drücken Sie auf den orangefarbenen Griff, um das Modul zu lösen. b.
1 2 CL5984 Abbildung 130. Entfernen eines Netz-/Kühlungsmoduls (Wechselstrom) Einbauen eines Netz-/Kühlungsersatzmoduls Schritte 1. So bauen Sie innerhalb von zwei Minuten das Netz-/Kühlungsmodul in das Gehäuse ein: a. Führen Sie das Netz-/Kühlungsmodul vorsichtig in das Gehäuse ein und sorgen Sie dafür, dass das Modul vollständig im Gehäuse sitzt. b. Drücken Sie die Verriegelung nach innen, um das Netz-/Kühlungsmodul zu sichern.
1 2 CL5990 Abbildung 131. Einbau eines Netz-/Kühlungsmoduls 2. Für ein Netzteil/Lüfter-Modul (Wechselstrom): a. Verbinden Sie das Netzkabel mit dem Netz-/Kühlungsmodul. b. Befestigen Sie das Kabel mit dem Sicherheitsbügel am Anschluss Die Bügel verhindern, dass das Netzkabel aus den Anschlüssen gezogen wird.
Abbildung 132. Anschließen des Netzkabels 3. Drücken Sie für ein Netz-/Kühlungsmodul (Gleichstrom) den Netzkabelstecker in die Buchse, bis er einrastet. Prüfen der Funktion eines Netzteil/Lüfter-Ersatzmoduls Schritte 1. Wählen Sie in PowerStore Managerdie Option Hardware aus. 2. Wählen Sie die Appliance aus, auf der Sie das fehlerhafte Netzteil/Lüfter-Modul ersetzt haben. 3. Erweitern Sie auf der Karte Components unter Rear View die Option ExpansionEnclosure. 4. Wählen Sie die entsprechende PSU aus.
A Sicherheitsvorkehrungen für den Umgang mit austauschbaren Einheiten Lesen Sie diese Sicherheitshinweise vor dem Austauschen von Teilen, um Schäden am System zu vermeiden. Themen: • Umgang mit austauschbaren Modulen Umgang mit austauschbaren Modulen In diesem Abschnitt werden die Vorsichtsmaßnahmen und die generelle Vorgehensweise beim Entfernen, Installieren und Lagern von austauschbaren Modulen erläutert.
Bewegen Sie sich dabei nicht mehr im Raum und berühren Sie keine anderen Einrichtungsgegenstände, Personen oder Oberflächen, bis Sie die Komponente eingebaut haben. ● Berühren Sie nach der Entnahme der Einheit aus ihrem antistatischen Beutel keine elektronischen Teile und Schaltkreise. ● Wenn Sie sich vor dem Einbau einer Einheit innerhalb des Raums bewegen oder andere Oberflächen berühren müssen, legen Sie die Einheit zuvor zurück in ihren antistatischen Beutel.
● Bei der Handhabung von Replaceable Units verhindern Sie elektrostatische Entladungen (ESD), indem Sie antistatische Handschuhe oder ein antistatisches Armband mit Riemchen tragen. Zusätzliche Informationen finden Sie unter Vermeiden Sie Schäden durch elektrostatische Entladung (ESD) auf Seite 109. ● Vermeiden Sie die Berührung freiliegender elektronischer Teile und Schaltkreise des Replaceable Unit. ● Wenden Sie beim Entfernen oder Einsetzen einer Replaceable Unit nie übermäßig viel Kraft auf.
B Ein-/Ausschaltverfahren Hier erfahren Sie, wie Sie das System ein- und ausschalten.
○ Beenden Sie den Servicemodus (Argument reboot). ○ Schalten Sie den Node ein (Argument power_on). Weitere Informationen zu den Serviceskripts finden Sie im PowerStore – Handbuch zu Serviceskripten. ● Wenn beide Nodes in einer Appliance im Servicemodus neu gestartet werden, muss immer zuerst Node A einer Appliance wieder in den Normalmodus versetzt werden, um Konflikte der Managementsoftware zu vermeiden. Sobald Node A ordnungsgemäß funktioniert, können Sie Node B wieder in den Normalmodus versetzen.
Tabelle 5. Vorschau der Ein-/Ausschaltverfahren (fortgesetzt) Komponente Aktion PowerStore T-Modell PowerStore X-Modell setzen Sie sie wieder ein. Schließen Sie die Netzkabel wieder in der richtigen Reihenfolge an. setzen Sie sie wieder ein. Schließen Sie die Netzkabel wieder in der richtigen Reihenfolge an und verwenden Sie VMware vCenter Server.
Ausschalten eines PowerStore T-Modell-Node mit einem Serviceskript Voraussetzungen Ermitteln Sie die folgenden Informationen: ● Management-IP-Adresse der Appliance, die den Node enthält. Navigieren Sie in PowerStore Manager zu Settings > Networking > Networking IPs > Management. Überprüfen Sie die Tabelle Management IPs, um die der Appliance zugeordnete Management-IPAdresse zu identifizieren.
Schritte 1. Melden Sie sich beim zugehörigen vCenter Server an. 2. Wenn Nutzer-VMs nicht für die automatische Migration auf den ESXi-Host des Peer-Node konfiguriert wurden, migrieren Sie sie manuell. ANMERKUNG: vSPHERE Remote Office Branch Office Advanced unterstützt nicht die die automatische Migration. 3. Wenn Nutzer-VMs nicht auf den ESXi-Host des Peer-Node migriert werden können, fahren Sie sie manuell herunter. 4. Versetzen Sie den ESXi-Host für den PowerStore X-Modell Node in den Wartungsmodus.
Einschalten eines PowerStore T-Modell-Node durch Neueinsetzen des Node Info über diese Aufgabe Gehen Sie wie folgt vor, um einen PowerStore T-Modell-Node einzuschalten (hochzufahren), wenn er aus dem Gehäuse entfernt wurde: Schritte 1. Setzen Sie den Node wieder in das Gehäuse ein. Der Node wird automatisch eingeschaltet. 2. Schließen Sie das Netzkabel wieder an. 3. Warten Sie, bis der Node vollständig eingeschaltet ist.
Schritte 1. Setzen Sie den Node wieder in das Gehäuse ein. Der Node wird automatisch eingeschaltet. 2. Schließen Sie das Netzkabel wieder an. 3. Warten Sie, bis der ESXi-Host für den Node vollständig eingeschaltet ist. 4. Melden Sie sich bei dem zugehörigen vCenter Server an und beenden Sie den Wartungsmodus des ESXi-Hosts für den Node. Die Controller-VM schaltet sich automatisch ein. ANMERKUNG: Überspringen Sie diesen Schritt beim Austausch des primären internen M.2-Boot-Moduls.
● Management-IP-Adresse der Appliance, die den Node enthält. Navigieren Sie in PowerStore Manager zu Settings > Networking > Networking IPs > Management. Überprüfen Sie die Tabelle Management IPs, um die der Appliance zugeordnete Management-IPAdresse zu identifizieren. ● Zugangsdaten für das Servicekonto ANMERKUNG: Schalten Sie einen Node nicht aus oder starten Sie ihn nicht neu, wenn der Peer-Node nicht ordnungsgemäß funktioniert.
6. Nachdem alle VMs migriert wurden und der Node in den Wartungsmodus wechselt, starten Sie den ESXi-Host mit vCenter-Befehlen neu. 7. Überwachen Sie die vCenter Server-Konsole, um sicherzustellen, dass der ESXi-Host neu gestartet wurde, und beenden Sie dann den Wartungsmodus für den ESXi-Host. Die Controller-VM schaltet sich automatisch ein. 8. Überwachen Sie die vCenter Server-Konsole, um sicherzustellen, dass der ESXi-Host und die Controller-VM in den Normalbetrieb zurückgekehrt sind.
Ausschalten einer PowerStore X-Modell-Appliance Voraussetzungen ● Schalten Sie die Appliance beim Austauschen einer Hardwarekomponente nicht aus. Identifizieren Sie den Node, der die fehlerhafte Hardwarekomponente enthält, und schalten Sie nur diesen Node aus. Weitere Informationen finden Sie unter Ausschalten eines PowerStore X-Modell-Node auf Seite 115. ● Durch das Ausschalten einer Appliance können die zugeordneten Hosts nicht mehr auf die Daten auf der Appliance zugreifen.
14. Warten Sie, bis PowerStore Manager bestätigt, dass die Appliance offline ist, um sicherzustellen, dass die ESXi-Hosts heruntergefahren wurden. 15. Überwachen Sie die vCenter Server-Konsole, um sicherzustellen, dass die ESXi-Hosts heruntergefahren wurden. 16. Warten Sie 5 Minuten und trennen Sie dann bei Bedarf die Netzkabel vom Basisgehäuse und den Erweiterungsgehäusen.
Die Node-Betriebs-LED an jedem Node leuchtet auf, wenn das Netzkabel an einen Node angeschlossen wird. ESXi-Hosts für beide Nodes werden im Wartungsmodus eingeschaltet. 5. Melden Sie sich bei dem zugehörigen vCenter Server an und beenden Sie den Wartungsmodus des ESXi-Hosts für Node A. Warten Sie, bis die Aufgabe abgeschlossen ist. 6. Klicken Sie in vCenter Server mit der rechten Maustaste auf die Controller-VM für Node A und schalten Sie sie ein.
3. Nachdem Sie überprüft haben, ob der Cluster heruntergefahren wurde, können Sie gegebenenfalls die Netzkabel von beiden Nodes in einem der Basisgehäuse im Cluster trennen. Warten Sie einige Sekunden und vergewissern Sie sich, dass alle übrigen LEDs nicht mehr leuchten. 4. Ziehen Sie gegebenenfalls die Netzkabel von allen zugehörigen Erweiterungsgehäusen ab, um sie auszuschalten. 5.
Einschaltverfahren für PowerStore-Cluster Dieser Abschnitt beinhaltet die folgenden Verfahren: ● Einschalten eines PowerStore T-Modell-Clusters auf Seite 125 ● Einschalten eines PowerStore X-Modell-Clusters auf Seite 125 Einschalten eines PowerStore T-Modell-Clusters Info über diese Aufgabe Gehen Sie wie folgt vor, um einen PowerStore T-Modell-Cluster einzuschalten: Schritte 1. Wenn die Nodes entfernt wurden, setzen Sie sie wieder in den Rahmen des relevanten Basisgehäuses ein. 2.
Tabelle 7.
C Umsetzen der Internes Batteriebackupmodul Erfahren Sie, wie Sie die Internes Batteriebackupmodul von einer fehlerhaften Node in eine Ersatz-Node umsetzen. ANMERKUNG: Lesen Sie vor dem Umgang mit austauschbaren Teilen die Informationen unter Sicherheitsvorkehrungen für den Umgang mit austauschbaren Einheiten auf Seite 109. Themen: • • Entfernen der Internes Batteriebackupmodul Installieren des Internes Batteriebackupmodul Entfernen der Internes Batteriebackupmodul Schritte 1.
Abbildung 134. Entfernen des Batteriebackupmoduls von der Hauptplatine Installieren des Internes Batteriebackupmodul Installieren Sie das Internes Batteriebackupmodul in den Ersatz-Node. Schritte 1. Platzieren Sie das Internes Batteriebackupmodul auf der Hauptplatine. Abbildung 135. Einsetzen des Internes Batteriebackupmoduls 2. Schließen Sie die Klammer um die Mitte des Internes Batteriebackupmoduls, bis es hörbar einrastet. 3.
Abbildung 136.
D Datenerfassung Erfahren Sie, wie Sie Supportmaterialien sammeln können, um die Fehlerbehebung bei den Appliances in Ihrem System zu erleichtern. Themen: • • Sammeln von Supportmaterialien Sammeln von Supportmaterialien Sammeln von Supportmaterialien Sie können Supportmaterialien sammeln, um die Fehlerbehebung bei den Appliances in Ihrem System zu erleichtern. Je nach ausgewählter Option können die Materialien Systemprotokolle, Konfigurationsdetails und andere Diagnoseinformationen enthalten.
Ergebnisse Wenn der Job abgeschlossen ist, sind die Jobinformationen, einschließlich des Status, auf der Seite Support Materials zu sehen. Nächste Schritte Nachdem der Job abgeschlossen ist, können Sie die Erfassung von Supportmaterialien auf einen Client herunterladen, sie an den Support senden oder sie löschen. Wählen Sie die Erfassung von Supportmaterialien und anschließend Download, Send to Support oder Delete aus.
E Supportbenachrichtigungen Erfahren Sie, wie Sie Supportbenachrichtigungen deaktivieren und aktivieren. Themen: • • Deaktivieren von Supportbenachrichtigungen Aktivieren von Supportbenachrichtigungen Deaktivieren von Supportbenachrichtigungen Um zu vermeiden, dass der Kundensupport unnötigerweise über einen Ausfall informiert wird, deaktivieren Sie die Supportbenachrichtigungen, bevor Sie Verfahren starten, die dazu führen, dass ein Node durch Ausschalten oder Neustarten getrennt wird. Schritte 1.
F Erneutes Initialisieren des Systems Erfahren Sie, wie das gesamte System auf die ursprünglichen Standardwerkseinstellungen zurückgesetzt wird. Themen: • Erneutes Initialisieren des Systems Erneutes Initialisieren des Systems Bei der Neuinitialisierung des Systems werden im gesamten System die Standardwerkseinstellungen wiederhergestellt. Sie können das System mithilfe von Serviceskripten neu initialisieren.