Dell EMC PowerStore PowerStore T 型号的网络连接指南 版本 2.x 6 月 2021 年 Rev.
注意、小心和警告 注: “注意”表示帮助您更好地使用该产品的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告: “警告”表示可能会导致财产损失、人身伤害甚至死亡。 © 2020 年 - 2021 年 Dell Inc. 或其子公司。保留所有权利。Dell、EMC 和其他商标是 Dell Inc.
目录 其他资源.........................................................................................................................................6 章 1: 概述........................................................................................................................................ 7 PowerStore T 型号 设备概述.............................................................................................................................................. 7 PowerStore T 型号 初始部署和存储网络配置............................
部分 II: 添加存储服务...................................................................................................................... 35 章 8: 存储服务概述.....................................................................................................................36 存储服务.........................................................................................................................................................................36 章 9: 准备为存储服务配置交换机和网络..................................................
用线缆将节点连接到 ToR 交换机..............................................................................................................................68 在 ToR 交换机上配置 VLAN....................................................................................................................................... 69 添加 IP 地址并将存储网络映射到端口..................................................................................................................... 70 附录 B: 创建其他存储网络........................................................
序言 为了不断改进,我们将定期发布软件和硬件产品的修订版。本文档中介绍的一些功能可能不被当前使用的软件或硬件的所有版本支 持。本产品发行说明提供了有关产品功能的新信息。如果某产品不能正常运行或其功能与本文档的描述不符,请与您的服务提供商 联系。 从何处获得帮助 可以按如下方式获取支持、产品和许可信息: ● 产品信息 有关产品和功能的文档或发行说明,请访问 PowerStore 文档页面,地址为 https://www.dell.com/powerstoredocs。 ● 故障排除 有关产品、软件更新、许可和服务的信息,请转到 https://www.dell.com/support,并找到相应的产品支持页面。 ● 技术支持 如需技术支持,如有服务请求,请转至 https://www.dell.
1 概述 本章包含下列信息。 主题: PowerStore T 型号 设备概述 PowerStore T 型号 初始部署和存储网络配置 支持的交换机 • • • PowerStore T 型号 设备概述 支持数据块(存储区域网络 (SAN))、文件(网络连接存储 (NAS))和虚拟卷 (vVol) 工作负载,其软件体系直接部署在系统裸机 上。 PowerStore T 型号 型号: ● ● ● ● ● ● 500T 1000T 3000T 5000T 7000T 9000T 注: 此型号不支持虚拟机管理程序部署。PowerStore X 型号 设备支持虚拟机管理程序部署。 支持文档 除了通读本文档,您还应在配置交换机和网络之前通读以下指南: ● ● ● ● ● PowerStore 快速入门指南 PowerStore 规划指南 PowerStore 硬件信息指南 PowerStore 1000、3000、5000、7000 和 9000 型号的安装和服务指南 PowerStore 500T 型号的安装和服务指南 PowerStore T 型号 初始部署和存储网络配置 安装 PowerStore
表. 1: PowerStore T 型号 部署选项 (续) 部署选项 协议和服务 交换机要求 有关详细信息,请参阅 使用统一部署,您的存储服 务可以包括对网络连接存储 (NAS) 的支持。 支持的交换机 PowerStore 可与以下运行 OS10 企业版 (OS10EE) 的 Dell EMC PowerSwitch 系列共同购买。 ● S4148F-ON ● S4148T-ON ● S5248F-ON 本指南的规划和要求部分可用于准备使用任何受支持的交换机来部署 PowerStore 设备。但是,本指南中提供的配置步骤是使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机来部署 PowerStore 的具体步骤。 如果您不打算使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机部署 PowerStore,请参阅 PowerStore 第三方交换机简单支持矩 阵,以查看受支持交换机的列表。第三方交换机简单支持矩阵可从 Dell EMC eLab Navigator 获取,网址为:https:// elabnavigator.emc.
I 初始部署 本部分包含完成 PowerStore T 型号 的初始部署的信息。 主题: • • • • • • PowerStore T 型号 的初始部署概述 准备配置管理交换机和网络 初始部署的交换机和网络要求 配置 Dell PowerSwitch 系列以进行初始部署 发现 PowerStore 设备 PowerStore T 型号 设备的初始配置 初始部署 9
2 PowerStore T 型号 的初始部署概述 主题: • PowerStore T 型号 的初始部署 PowerStore T 型号 的初始部署 PowerStore T 型号 的初始部署要求您配置管理交换机和网络。 配置管理交换机并将其连接到 PowerStore T 型号 节点后,您将发现 PowerStore T 型号 设备并在 PowerStore Manager 初始配置向导 中配置网络。 完成初始部署后,PowerStore T 型号 将配置为支持光纤通道连接。 如果您想要支持 iSCSI 主机连接、复制、导入、群集或网络连接存储 (NAS) 等服务,则需要执行第 2 部分:添加存储服务中所述的 其他配置步骤。 10 PowerStore T 型号 的初始部署概述
3 准备配置管理交换机和网络 本章包含下列信息。 主题: 保留用于初始部署的网络资源 填写初始配置工作表中的必填字段 • • 保留用于初始部署的网络资源 与网络管理员一起填写以下两个工作表,以便保留 PowerStore T 型号 设备的初始部署所需的资源。 有关用于部署 PowerStore T 型号 设备的要求和网络资源的详细信息,请参阅初始部署的交换机和网络要求。 如果您将在初始部署后为其他协议和服务配置架顶式 (ToR) 交换机,则可能还希望现在保留配置 ToR 交换机所需的资源。请参阅存 储网络准备工作表。 完成后,管理网络准备工作表将具有为 PowerStore T 型号 设备的初始部署配置管理交换机所需的资源列表。 表. 3: 管理网络准备工作表 步骤 步骤详细信息 注释 1. 打印此表以记录保留的资源。 2. 打印初始配置工作表以记下您首次创建群集时在 PowerStore T 型号 中创建网络将需要的其他网络资源。 3. 记录要连接到的管理交换机端口: 节点 A 管理 1GbE 端口到 节点 B 管理 1GbE 端口到 4.
有关 Dell EMC PowerSwitch 系列的填写好的管理网络准备工作表的示例,请参阅填写好的管理网络准备工作表示例。 填写初始配置工作表中的必填字段 填写初始配置工作表后,将具有运行 PowerStore T 型号初始配置向导所需的资源列表,必须完成该向导才能访问 PowerStore Manager 用户界面。 发现 PowerStore T 型号 后会自动启动初始配置向导。如果没有以下信息,您将无法继续执行 PowerStore T 型号 的初始配置。 表.
表.
4 初始部署的交换机和网络要求 本章包含下列信息。 主题: • • • • 管理交换机要求 初始部署所需的网络类型 初始部署期间的 VLAN 选项 初始部署的 IP 要求 管理交换机要求 所有 PowerStore T 型号 部署都需要使用至少一个带外管理交换机进行部署。 节点到管理交换机 管理交换机通过每个设备基本存储模块节点上的 1 GbE 管理端口进行连接,如下图所示。 PowerStore T Management Switch Network Topology Management Switch Port Channel Port 0 Port 1 Port 1 Port 0 Node A Node B Mgmt Mgmt PowerStore T Appliance Legend: 10 Gb 1 Gb 图 1: 管理交换机网络拓扑 注: 要远程发现 PowerStore T 型号,管理交换机端口必须支持未标记的本机 VLAN 流量。 14 初始部署的交换机和网络要求
下图显示了管理端口在 PowerStore T 型号 基本存储模块节点上所处的位置。 Node A Management Port Node B Management Port 图 2: PowerStore T 型号 基本存储模块节点管理端口 管理交换机上行链路连接 下图显示了连接到两个第 3 层上行链路设备的管理交换机的示例。两个连接都经过一个端口通道,它可提供更高的带宽和冗余。 初始部署的交换机和网络要求 15
PowerStore T Management Switch Network Topology with Upstream Switches Management Upstream Switch1 Management Upstream Switch2 Management Switch Port Channel Port 0 Port 1 Port 1 Port 0 Node A Node B Mgmt Mgmt PowerStore T Appliance Legend: 10 Gb 1 Gb 图 3: 具有上行链路连接的管理交换机网络拓扑 初始部署所需的网络类型 PowerStore T 型号 要求所有网络都是唯一的。强烈建议使用多个唯一的 VLAN 部署 PowerStore T 型号,以分离流量。但是,如果只 有一个可用 VLAN,您可以选择使用单个 VLAN 和多个唯一子网部署 PowerStore T 型号,如下图所示。 必须在管理交换机上配置以下网络以进行初始部署。 16 初始部署的交换机和网络要求
PowerStore T Logical Networks Management Upstream Management switch PowerStore T Management Subnets Management Remote Discovery 图 4: PowerStore T 型号 逻辑网络流量 所有流量都通过基本存储模块节点上的专用 1 GbE 管理端口进行传输。 确保您的 PowerStore T 型号 能够通过上面所示子网进行通信。请参考您的网络供应商文档,确保所有正常的 L2 和/或 L3 流量均在 PowerStore T 型号 利用的所有网络中适当路由。 表.
初始部署期间的 VLAN 选项 下图显示了用于 PowerStore T 型号 的初始部署的不同 VLAN 选项的示例。 PowerStore T – Untagged Management VLAN Management Management switch PowerStore T Sample ID 100 100 Traffic Remote Discovery PowerStore Management Untagged Traffic Tagged Traffic Subnet 169.254.x.x/16 y.y.y.
PowerStore T – Tagged Management VLAN Management Upstream Management switch PowerStore T Sample ID 100 101 Traffic PowerStore Management Remote Discovery Untagged Traffic Tagged Traffic Subnet y.y.y.y/24 169.254.x.
存储网络 在初始部署期间,存储网络没有 IP 要求。但是,如果您稍后在 PowerStore Manager、REST API 或 CLI 中添加存储网络,则需要它们 的 IP 地址。请参阅添加存储服务。 20 初始部署的交换机和网络要求
5 配置 Dell PowerSwitch 系列以进行初始部署 本章包含下列信息。 主题: • • • • • • 使用 Dell EMC PowerSwitch 系列 S4148 交换机进行配置的概述 将管理交换机安装到 PowerStore T 型号 机柜中 获取填写好的管理网络准备工作表 配置管理交换机以进行初始部署的步骤 验证管理交换机上的配置 Network Validation Tool for PowerStore 使用 Dell EMC PowerSwitch 系列 S4148 交换机进行配置 的概述 本部分介绍在单个群集中部署 PowerStore T 型号 的步骤,该群集包含一个设备,其中单个基本存储模块连接到 Dell PowerSwitch 系 列 S4148 管理交换机。 如果您不打算使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机部署 PowerStore,请参阅 PowerStore 第三方交换机简单支持矩 阵,以查看受支持交换机的列表。第三方交换机简单支持矩阵可从 Dell EMC eLab Navigator 获取,网址为:https://
表. 7: 管理网络准备工作表(已填写) 步骤 步骤详细信息 注释 1. 打印此表以记录保留的资源。 2. 打印初始配置工作表 以记下您首次创建群集时在 PowerStore T 型号中创建网络将需要的其他网络资源。 3. 记录要连接到的管理交换机端口: 节点 A 管理 1GbE 端口到 管理交换机端口 2 节点 B 管理 1GbE 端口到 管理交换机端口 53 4. (可选)记录管理交换机上用于远程发现的端口。 管理交换机端口 1 5. 记录管理交换机上将用于连接到上行链路的端口。 6. 7. 管理上行链路 A 到 管理交换机端口 25 管理上行链路 B 到 管理交换机端口 26 记录将在管理交换机上使用的 VLAN ID: 管理(无标记) 100 远程发现(无标记) 100 保留并记录配置以下交换机所需的 IP 地址: 管理交换机的管理 IP 地址 100.0.100.50/24 默认网关 100.0.100.1 NTP 服务器 100.0.100.200 8. 记录管理交换机的端口通道 ID。 端口通道 10 9.
您必须建立到每个交换机的终端会话以配置交换机,做好部署准备。 1. 打开交换机的电源。 2. 使用串行线缆将计算机连接到串行控制台端口,即位于 PowerSwitch 的 PSU 一侧的顶部端口。 Serial Console Port Management Port 3. 打开计算机上的终端仿真程序,例如 PuTTY。 4. 使用以下设置在终端仿真程序中配置串行连接。 表. 8: 串行连接设置 设置 值 Speed(baud) 115200(micro-USB 端口为 9600) 数据位 8 停止位 1 奇偶校验 None 流控制 None 5. 使用终端仿真程序连接到交换机。 6. 输入交换机登录凭据。默认用户名和密码为: ● 用户名:admin ● 密码:admin 7. 进入全局配置模式。 configure terminal 8.
运行命令 show license status 以显示许可证安装。License Type: 字段应显示为 PERPETUAL。如果已安装评估许可 证,则从 Dell EMC 购买的许可证可在 Dell Digital Locker (www.dell.com/support/software/) 下载。 OS10# show license status System Information --------------------------------------------------------Vendor Name : Dell EMC Product Name : S4148F-ON Hardware Version: A00 Platform Name : x86_64-dellemc_s4100_c2538-r0 PPID : CN00Y2VTCES0082O0038 Service Tag : D8MSG02 License Details ---------------Software : OS10-Enterprise Version : 10.4.1.
注: 以下命令示例假定在交换机上启用了通过动态主机配置协议 (DHCP) 进行的自动 IP 分配。如果通过 DHCP 的自动 IP 分配 未启用,则不需要在下面的命令中包括 no ip address dhcp。 interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.50/24 exit 7. 为交换机配置管理路由(默认网关)。 management route 0.0.0.0/0 100.0.100.1 exit 8. 为交换机配置 NTP 服务器。 ntp server 100.0.100.200 exit 9.
用线缆连接管理交换机 用线缆将管理交换机连接到设备基本存储模块节点和管理上行链路。 本指南中的示例演示如何使用 Dell EMC PowerSwitch S4148-ON 交换机部署 PowerStore T 型号 设备。 用线缆将节点上的管理端口连接到管理交换机 管理交换机通过每个设备基本存储模块节点上的 1 GbE 管理端口进行连接。 1 图 7: 基本存储模块设备与管理交换机的连接 表.
Layer 3 – Management Uplinks Management Uplink A Management Uplink B 2 1 图 8: 管理交换机与管理上行链路的连接 表. 11: 将管理交换机连接到管理上行链路的步骤 1 将管理交换机端口 25 连接到管理上行链路 A。 2 将管理交换机端口 26 连接到管理上行链路 B。 注: 与您的网络管理员一起确定要连接到管理交换机的上行链路端口。 验证管理交换机上的配置 配置管理交换机并用线缆将交换机连接到您的 PowerStore T 型号 节点后,请在发现 PowerStore T 型号 之前验证交换机配置。 1. 与交换机建立终端会话。 2. 验证接口状态。 show interface status | grep up Port Eth 1/1/1 Eth 1/1/2 Eth 1/1/25 Eth 1/1/26 Eth 1/1/53 Description discoveryWork.. PowerStoreNod.. Uplink_Ports Uplink_Ports PowerStoreNod..
3. 验证端口通道配置。 show port-channel summary Flags: D - Down I - member up but inactive P - member up and active U - Up (port-channel) F - Fallback Activated -------------------------------------------------------------------------------Group Port-Channel Type Protocol Member Ports -------------------------------------------------------------------------------10 port-channel10 (U) Eth DYNAMIC 1/1/25(P) 1/1/26(P) 4.
6 发现 PowerStore 设备 本附录包含以下信息。 主题: • • 通过直接连接发现 通过远程连接发现 通过直接连接发现 这是建议步骤,要求您亲临安装了基本存储模块的位置。 ● (可选)下载并运行 PowerStore 网络验证工具 (NVT),验证您的网络是否已正确配置。可从 Dell EMC Central Solutions 下载 NVT,网址为:https://psapps.emc.com/central/solutions。 ● 确保工作站的网络适配器配置如下: ○ 直接连接到节点 A 上的 PowerStore 服务端口。 ○ 在服务 LAN 端口 (128.221.1.0/24) 上配置静态 IP 地址,且未定义网关地址(128.221.1.249;255.255.255.0;无网关) ○ 能够 ping 通节点 A 服务 LAN 端口 (128.221.1.250) 的 IP 地址 1.
通过远程连接发现 Network Node 如果您无法接触到基本存储模块,请在与 PowerStore 系统相同的网络上部署一个工作站或虚拟机,并使用 PowerStore 发现实用程 序来发现和创建群集。 B A 图 9: PowerStore T 型号 远程发现连接 有两种发现方法可供选择: ● 使用发现工具进行远程发现 ● 使用静态 IP 地址进行远程发现 使用发现工具进行远程发现 您可以使用发现工具来发现 PowerStore,该工具会广播一个 169.254.xx/16 IP 地址。 ● (可选)下载并运行 PowerStore 的网络验证工具 (NVT),验证您的网络是否已正确配置。可从 Dell EMC Central Solutions 下载 NVT,网址为:https://psapps.emc.
○ 验证是否有以 169.254.0.x/16 开头的 IP 地址,可将其用作第二个网络适配器的 IP 地址。如果此 IP 地址不可用,则将第二个 网络适配器的 IP 地址设置为 169.254.1.2,使用网络掩码 255.255.0.0,并且不定义网关地址。任何其他地址范围(无论是使用 DHCP 还是静态 IP 地址)都不能覆盖此地址。 注: 为避免 IP 地址重复,请确保您设置了 169.254.x.x IP 地址的本机/未标记网络中只有一台笔记本电脑或虚拟机。 1. 在工作站或虚拟机中,打开网页浏览器,然后输入为访问 PowerStore Discovery Utility 而保留的任一 IP 地址。 ● http://169.254.0.10 ● http://169.254.0.20 ● http://169.254.0.30 ● http://169.254.0.40 ● http://169.254.0.50 2.
7 PowerStore T 型号 设备的初始配置 本章包含下列信息。 主题: • • 初始配置向导 获取填写好的初始配置工作表 初始配置向导 发现 PowerStore T 型号 设备后,会将您重定向到初始配置向导(ICW) 来配置 PowerStore T 型号 设备上的网络。 初始配置向导(ICW) 会提示您输入 PowerStore T 型号 设备的初始配置所需的网络信息。 在运行 ICW 时,请参阅填写好的初始配置工作表。初始配置工作表中应已填写了完成 PowerStore T 型号 设备的初始部署所需的所 有信息。 在运行 ICW 时,请注意以下事项: ● 登录凭据 首次登录 PowerStore 时,您将使用默认用户名和密码。但是,您必须先更改管理员密码,然后才能继续完成初始配置向导 (ICW)。请务必在填写好的初始配置工作表中记下您为群集输入的新管理员密码。尚未为您提供此密码的示例。 ● 群集详细信息选择: ○ 统一是默认选择。如果以后要添加网络连接存储 (NAS) 服务,请保留此选择。如果您现在未选择统一,则以后需要先联系您 的服务提供商,然后才能添加 NAS 服务。 ○ 数据块优化针
表.
表. 12: 初始配置工作表(已填写) (续) DNS 服务器 100.0.100.200 100.0.100.201 NTP 服务器 100.0.100.200 100.0.100.201 带外管理交换机(管理交换机)信息 MngmtSwitch 不适用 协议 (SSH/SNMP) SSH 不适用 IP 地址 100.0.100.
II 添加存储服务 本部分包含有关为 PowerStore T 型号 准备交换机并配置 Dell EMC PowerSwitch 系列以使用其他协议和服务的信息。 主题: • • • • • • • 存储服务概述 准备为存储服务配置交换机和网络 使用 ToR 交换机进行部署的交换机和网络要求 使用 Dell PowerSwitch 系列 S4148 架顶式交换机来配置 PowerStore T 型号 为存储服务用线缆连接 Dell PowerSwitch 系列 ToR 交换机 使用 ToR 交换机验证 PowerSwitch 系列配置 在 PowerStore Manager 中配置存储和 NAS 网络 添加存储服务 35
8 存储服务概述 本章包含以下信息 主题: • 存储服务 存储服务 在初始部署之后为光纤通道配置 PowerStore T 型号 设备。您可以选择在初始部署之后添加存储服务。 存储服务包括以下协议和服务: ● ● ● ● ● iSCSI 主机连接 复制 导入 群集 网络连接存储 (NAS) 注: NAS 仅包含在统一部署中。 添加存储服务的交换机要求 要添加存储服务,您必须将 PowerStore T 型号 设备连接到两个架顶式 (ToR) 交换机。 本文档介绍通过单个群集部署 PowerStore T 型号 的步骤,该群集包含一个设备,其中单个基本存储模块连接到 Dell PowerSwitch 系 列 S4148 交换机。 36 存储服务概述
9 准备为存储服务配置交换机和网络 本章包含下列信息。 主题: 存储服务的交换机资源工作表 存储网络配置工作表 • • 存储服务的交换机资源工作表 与网络管理员一起填写存储服务的交换机资源工作表,并保留必要的资源来配置存储服务所需的两个架顶式 (ToR) 交换机。 有关为 Dell PowerSwitch 系列填写的存储服务的交换机资源工作表的示例,请参阅填写好的存储服务的交换机资源工作表示例。 注: 本部分假定您已完成初始部署,并且已成功配置管理交换机和网络。 此外,您可能同时想要与网络管理员一起填写存储网络配置工作表,以便保留在 PowerStore Manager 中创建存储网络所需的资源。 表. 13: 存储服务的交换机资源(空白) 步骤 步骤详细信息 注释 1. 打印此表以记录保留的资源。 2.
表. 13: 存储服务的交换机资源(空白) (续) 步骤 步骤详细信息 注释 选择您将使用哪一类型的第 2 层互连: 极力建议:多机箱链路聚合组 (MC-LAG) 如果您将使用 MC-LAG,请记录将用于将交换机连接在一起的端口。 ToR 交换机 1 至 ToR 交换机 2 端口对 1 ToR 交换机 1 至 ToR 交换机 2 端口对 2 或者,不使用 MC-LAG 的 L2 上行链路 6. 如果使用 MC-LAG,请输入域 ID。 7. 如果对第 2 层互连使用 MC-LAG (VLT),请记录以下各项: 将用于交换机 1 和交换机 2 的 VLT MAC 地址。 对交换机 1 和交换机 2 使用相同的 VLT MAC 地址。 注: 对于 VLT MAC 地址,不可以使用全零 (00:00:00:00:00)。 ToR 交换机 1 的 VLT 优先级 ToR 交换机 2 的 VLT 优先级 8. 如果配置链路聚合控制协议 (LACP),请记录用于节点连接的 LACP(端口通道)ID: 节点 A 的端口通道 ID 节点 B 的端口通道 ID 9.
表.
10 使用 ToR 交换机进行部署的交换机和网络要求 本章包含以下信息。 主题: 架顶式 (ToR) 交换机连接选项和要求 添加存储服务时的网络配置 添加存储网络和 NAS 服务器时的 VLAN 选项 添加存储服务的存储网络 IP 地址要求 • • • • 架顶式 (ToR) 交换机连接选项和要求 除了在 PowerStore T 型号 设备的初始部署期间配置的管理交换机外,您还必须添加两个 ToR 交换机,以支持 iSCSI 连接、复制、导 入、群集和网络连接存储 (NAS)。 架顶式 (ToR) 交换机到 ToR 交换机 (L2) 连接选项 使用以下选项之一将两个 ToR 交换机连接在一起。 表. 15: ToR 交换机到 ToR 交换机互连选项 交换机互连选项 建议 1. 多机箱链路聚合组 (MC-LAG) 戴尔强烈建议使用 MC-LAG 来实现交换机之间的连接。 2.
PowerStore Network Topology with Top of Rack Switches and MC-LAG Interconnect Upstream Switch 2 Upstream Switch 1 Port Channel Top of Rack Switch 1 Port 0 MC-LAG Interconnect Port 1 Top of Rack Switch 2 Port 1 Node A Port 0 Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 图 10: 使用 MC-LAG 互连的 ToR 交换机 使用 ToR 交换机进行部署的交换机和网络要求 41
注: 可靠的高速上行链路的端口位置可能会因交换机供应商或型号而异。 MC-LAG 是一种交换机互连技术,可将大量独立的架顶式 (ToR) 交换机加入单个虚拟机箱。MC-LAG 允许链路聚合 (LAG) 端口组涵 盖多个机箱,从而实现 LAG 连接的更强恢复能力。此外,MC-LAG 允许交换机之间的流量使用可用连接的全部带宽,而无需使用生 成树协议 (STP),该协议会禁用一些链路来防止形成环路。 MC-LAG 是此技术的通用名称,但某些供应商使用自己的专有术语来定义 MC-LAG 连接。 表.
PowerStore Network Topology with a no MC-LAG interconnect Upstream Switch 2 Upstream Switch 1 Port Channels Top of Rack Switch 1 Port 0 Top of Rack Switch 2 Port 1 Port 1 Node A Port 0 Node B PowerStore T Appliance Legend: 10 Gb 1 Gb 图 11: 使用非 MC-LAG L2 互连的 ToR 交换机 使用 ToR 交换机进行部署的交换机和网络要求 43
注: 可靠的高速上行链路的端口位置可能会因交换机供应商或型号而异。 非 MC-LAG L2 连接需要冗余的高速连接。 节点与架顶式 (ToR) 交换机的连接 使用架顶式 (ToR) 交换机进行部署时,要求每个基本存储模块设备节点与每个 ToR 交换机至少有一个连接,以便在 NIC 和交换机级 别提供冗余。 图 12: 节点与 ToR 交换机之间的布线 在用缆线将节点与交换机连接时: ● 同一节点上的端口 0 和端口 1 必须连接到相反的交换机 ● 节点 A 上的端口 0 和节点 B 上的端口 0 必须连接到相反的交换机 ● 节点 A 上的端口 1 和节点 B 上的端口 1 必须连接到相反的交换机 添加存储服务时的网络配置 所有存储、NAS 服务器和内部流量都通过架顶式 (ToR) 交换机进行路由。 PowerStore T 型号 要求所有网络都是唯一的。强烈建议使用多个唯一的 VLAN 部署 PowerStore T 型号,以分离流量。但是,如果只 有一个可用 VLAN,您可以选择使用单个 VLAN 和多个唯一子网部署 PowerStore T 型号,如下图所示。 44 使用 ToR 交换机进行部署
PowerStore T – Production Subnets Production ToR 1 ToR 2 PowerStore T Production Subnets Storage NAS Internal 图 13: 具有存储服务的 PowerStore T 型号 的网络流量 确保您的 PowerStore T 型号 能够通过上面所示 VLAN 进行通信。请参考您的网络供应商文档,确保所有正常的 L2 和/或 L3 流量均 在 PowerStore T 型号 利用的所有网络中适当路由。 表.
表.
添加存储服务的存储网络 IP 地址要求 您将需要保留 IP 地址才能将一个或多个存储网络添加到 PowerStore T 型号 设备中。 您将需要为要添加的每个存储网络保留共 3 个 IP 地址: ● 每个设备 2 个 IP 地址 ● 每个群集 1 个 IP 地址 下表详细说明了 IP 地址分配。 表.
11 使用 Dell PowerSwitch 系列 S4148 架顶式交换 机来配置 PowerStore T 型号 本章包含下列信息。 主题: 使用 Dell EMC PowerSwitch 系列 S4148 交换机进行配置的概述 将架顶式交换机安装到 PowerStore T 型号 机柜中 为存储服务配置 Dell PowerSwitch 系列 • • • 使用 Dell EMC PowerSwitch 系列 S4148 交换机进行配置 的概述 本文档介绍通过单个群集部署 PowerStore T 型号 的步骤,该群集包含一个设备,其中单个基本存储模块连接到 Dell PowerSwitch 系 列 S4148 管理交换机和两个 Dell PowerSwitch 系列 S4148 架顶式 (ToR) 交换机。 如果您不打算使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机部署 PowerStore,请参阅 PowerStore 第三方交换机简单支持矩 阵,以查看受支持交换机的列表。第三方交换机简单支持矩阵可从 Dell EMC eLab Navigator 获取,网址为:
为存储服务配置 Dell PowerSwitch 系列 至少需要配置一个带外 (OOB) 管理交换机和两个架顶式 (ToR) 交换机,才能使 PowerStore T 型号 支持 iSCSI 主机连接、复制、导 入、群集或网络连接存储 (NAS)。 按照建议,以下步骤介绍了如何配置其间存在虚拟链路中继 (VLT) 第 2 层 (L2) 互连的两个 ToR 交换机。有关配置没有 VLT 互连的 PowerStore T 型号 部署的步骤,请参阅:配置没有 VLTi 的 PowerStore T 型号。 注: 虚拟链路中继 (VLT) 特定于 Dell PowerSwitch 连接。此业界术语也称为多机箱链路聚合组 (MC-LAG) 1. 2. 3. 4. 5. 6. 7. 8.
表. 20: 存储服务的交换机资源工作表(已填写) (续) 步骤 5. 步骤详细信息 注释 ToR 交换机 2 的管理 IP 地址 100.0.100.11/24 默认网关 100.0.100.1 NTP 服务器 100.0.100.200 Dell EMC 支持使用两个具有第 2 层互连链路的架顶 (ToR) 交换机部署 PowerStore T 型号。 选择您将使用哪一类型的第 2 层互连: 极力建议:多机箱链路聚合组 (MC-LAG) 如果您将使用 MC-LAG,请记录将用于将交换机连接在一起的端口。 ToR 交换机 1 至 ToR 交换机 2 端口对 1 25 到 25 ToR 交换机 1 至 ToR 交换机 2 端口对 2 26 到 26 或者,不使用 MC-LAG 的 L2 上行链路 不适用 6. 如果使用 MC-LAG,请输入域 ID。 VLT 域 ID 1 7.
与交换机建立终端会话 执行以下步骤,建立与 Dell EMC PowerSwitch 系列 S4148 交换机上的串行控制台端口的终端会话。 这些步骤是建立到 Dell EMC PowerSwitch S4148-ON 交换机的连接所特有的。 有关控制台串行端口线缆要求及更多详细信息,请参阅 Dell EMC PowerSwitch S4100-ON 系列安装指南,网址:https:// www.dell.com/support/home/us/en/04/product-support/product/networking-s4148f-on/docs。 您必须建立到每个交换机的终端会话以配置交换机,做好部署准备。 1. 打开交换机的电源。 2. 使用串行线缆将计算机连接到串行控制台端口,即位于 PowerSwitch 的 PSU 一侧的顶部端口。 Serial Console Port Management Port 3. 打开计算机上的终端仿真程序,例如 PuTTY。 4. 使用以下设置在终端仿真程序中配置串行连接。 表.
Copyright (c) 1999-2018 by Dell Inc. All Rights Reserved. OS Version: 10.4.1.2 Build Version: 10.4.1.2.524 Build Time: 2018-09-26T17:20:01-0700 System Type: S4148F-ON Architecture: x86_64 Up Time: 2 weeks 04:34:35 3. 确认交换机上已安装许可证。 运行命令 show license status 以显示许可证安装。License Type: 字段应显示为 PERPETUAL。如果已安装评估许可 证,则从 Dell EMC 购买的许可证可在 Dell Digital Locker (www.dell.
5. (可选)为交换机配置管理路由(默认网关)。 management route 0.0.0.0/0 100.0.100.1 6. 为交换机配置 NTP 服务器。 ntp server 100.0.100.200 7. 在交换机上启用快速生成树协议 (RSTP)。 spanning-tree mode rstp 8. 在交换机上配置生成树优先级。 spanning-tree rstp priority 40960 在选择生成树 rstp 优先级值时,请注意以下事项: ● 请务必与网络管理员一起确定要使用哪个值,以避免与网络中的其他交换机发生冲突。 ● 在配置交换机 1 和交换机 2 时,应使用不同的 rstp 优先级值。 ● 0 优先级通常为根桥保留。 9.
no switchport exit 4. 创建新 VLTi 域并选择 100 GbE 端口作为发现接口。 vlt-domain 1 discovery-interface ethernet 1/1/25-1/1/26 ● vlt-domainvlt-domain 和端口号在两个交换机上应该相同。 ● 端口 25 和 26 在 Dell EMC S4148-ON PowerSwitch 系列交换机上均为 100 GbE 端口。其他交换机可能为 100 GbE 端口分配了 不同的端口号。 5. 将另一个 ToR 交换机的管理 IP 指定为 VLT 备用(心跳信号需要它)。 ● 对于 switch1,使用 switch2 IP 地址作为备用目标。 ● 对于 switch2,使用 switch1 IP 地址作为备用目标。 backup destination 100.0.100.11 6. 启用对等路由以准备配置您的上行链路。对等路由可以启用或禁用到对等节点的 L3 路由。 注: 本指南中未介绍配置到客户网络的上行链路的步骤。 peer-routing 7.
2. 进入全局配置模式。 configure terminal 3. 创建内部网络。 interface vlan 1 description Internal_Network no shutdown exit 4. 在第二个 ToR 交换机 (Switch2) 上重复以上步骤。 configure terminal interface vlan 1 description Internal_Network no shutdown exit 在节点的交换机端口上配置 LACP 端口通道 配置 LACP 不是必需的,但极力建议这样做。4 端口卡的前 2 个端口聚合在 LACP 绑定中。如果配置了 LACP,这些端口将以主动/主 动模式运行。如果未设置 LACP,这些端口将以主动/被动模式运行。 LACP 要求在交换机上已经配置了虚拟链路中继互连 (VLTi)。有关详细信息,请参阅配置虚拟链路中继互连。 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3.
8. 将连接到 PowerStore T 型号 节点的端口配置为生成树协议 (STP) 边缘端口。 spanning-tree port type edge exit 9. 将面向节点 A 的端口移动到第一个端口通道组,并启用主动 LACP 模式。 注: 对于 iSCSI 最佳做法,建议按如下所示禁用流控制。 interface ethernet 1/1/1 channel-group 10 mode active flowcontrol receive off flowcontrol transmit off exit 10. 将面向节点 B 的端口移动到第二个端口通道组,并启用主动 LACP 模式。 注: 对于 iSCSI 最佳做法,建议按如下所示禁用流控制。 interface ethernet 1/1/54 channel-group 20 mode active flowcontrol receive off flowcontrol transmit off exit 11.
配置架顶 (ToR) 交换机上的上行链路端口 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3. 配置上行链路的端口通道。 interface port-channel 30 description Uplink no shutdown switchport mode trunk switchport access vlan 1 vlt-port-channel 30 4.
copy running-configuration startup-configuration 为 iSCSI 存储网络配置架顶式交换机 可以创建多个 iSCSi 网络。请参阅已填写的存储服务的网络准备工作表,以获得应在此步骤之前保留的 VLAN ID 的列表。 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3. 创建存储 VLAN。 interface vlan 200 description Storage_Network no shutdown exit 4. 为节点 A 端口配置存储 VLAN interface port-channel 10 switchport trunk allowed 200 exit 5. 为节点 B 端口配置存储 VLAN interface port-channel 20 switchport trunk allowed 200 exit 6.
(可选)配置架顶式交换机以支持 NAS 网络 仅统一部署支持网络连接存储。 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3. 创建 NAS VLAN。 interface vlan 300 description NAS_Network no shutdown exit 4. 为节点 A 端口配置存储 VLAN interface port-channel 10 switchport trunk allowed 300 exit 5. 为节点 B 端口配置存储 VLAN interface port-channel 20 switchport trunk allowed 300 exit 6. 为上行链路配置存储 VLAN interface port-channel 30 switchport trunk allowed 300 exit 7. 为要创建的每个 iSCSI 存储网络重复步骤 3 - 6。 8. 在第二个 ToR 交换机 (Switch2) 上重复步骤 1 - 7。 表.
12 为存储服务用线缆连接 Dell PowerSwitch 系列 ToR 交换机 本章包含以下信息。 主题: 用线缆将基本盘柜连接到 ToR 交换机 用线缆将 ToR 交换机连接在一起 用线缆将架顶交换机连接到核心上行链路 • • • 用线缆将基本盘柜连接到 ToR 交换机 用线缆将节点连接到架顶 (ToR) 交换机。 2 4 1 图 15: 基本盘柜与 ToR 交换机的连接 如示意图中所示,在将节点连线到 ToR 交换机时: ● 同一节点上的端口 0 和端口 1 必须连接到相反的交换机 ● 节点 A 上的端口 0 和节点 B 上的端口 0 必须连接到相反的交换机 ● 节点 A 上的端口 1 和节点 B 上的端口 1 必须连接到相反的交换机 表.
用线缆将 ToR 交换机连接在一起 使用 VLT 的 PowerStore 双交换机部署要求用线缆将两个架顶 (ToR) 交换机连接在一起。 1 2 图 16: 交换机到交换机连接 使用两根支持高速端口之间连接的线缆,例如 100Gbps 直接连接线缆 (DAC)。 表. 26: 可用的交换机到交换机端口 PowerSwitch 100 GbE 端口 S4148F-ON 25、26、29 和 30 S4148T-ON 25、26、29 和 30 S5248F-ON 49-54 建议您对顶部和底部交换机上的 VLTi 对使用相同的端口号。 表.
用线缆将架顶交换机连接到核心上行链路 用线缆将 Dell EMC PowerSwitch 系列 S4148-ON 架顶式 (ToR) 交换机连接到核心上行链路。 Core uplinks Uplink A 1 3 Uplink B 4 2 图 17: Dell EMC PowerSwitch 系列 S4148-ON ToR 交换机连接到核心上行链路 表.
13 使用 ToR 交换机验证 PowerSwitch 系列配置 本章包含下列信息。 主题: • • 验证架顶 (ToR) 交换机上的配置 将架顶式交换机添加到 PowerStore T 型号 部署后的网络验证工具 验证架顶 (ToR) 交换机上的配置 在您配置 ToR 交换机并完成布线后,在发现 PowerStore T 型号 机型部署之前请验证配置。 1. 与交换机建立终端会话。 2.
5.
9.
14 在 PowerStore Manager 中配置存储和 NAS 网 络 本章包含下列信息。 主题: 在 PowerStore Manager 中创建 iSCSI 存储网络 在 PowerStore Manager 中创建网络连接存储 (NAS) 服务 • • 在 PowerStore Manager 中创建 iSCSI 存储网络 为存储服务配置了 ToR 交换机后,您将需要在 PowerStore Manager 中创建支持 iSCSI 的存储网络。 PowerStore 最多支持 32 个存储网络,并且 4 端口卡上的每个端口最多 8 个。 获取适用于要添加到 PowerStore Manager 中的每个存储网络的已填写的存储网络配置工作表。 以下存储网络配置工作表已填写了本指南中所使用的网络资源。如果您不使用本指南中所使用的资源配置架顶式交换机,可使用与 您的环境相符的信息填写新的存储网络配置工作表。要下载空白工作表,请参阅存储网络配置工作表(空白)。 表.
有关配置要在其上添加另一个存储网络的其他交换机和节点端口的步骤,请参阅为其他存储网络配置端口。 在 PowerStore Manager 中创建网络连接存储 (NAS) 服务 在 PowerStore Manager 初始配置向导中选择统一模式时,将启用 NAS 服务。 配置 PowerStore Manager 后,将在您创建 NAS 服务器时在 PowerStore Manager 中创建网络。创建 NAS 服务器时,您将需要使用在 ToR 交换机上配置的相同 VLAN ID。 有关详细信息,请参阅以下两个文档: ● PowerStore 配置 NFS 导出指南 ● PowerStore 配置 SMB 共享指南 在 PowerStore Manager 中配置存储和 NAS 网络 67
A 扩展存储网络以跨多个端口运行 附录包含以下信息。 主题: 扩展存储网络 • 扩展存储网络 您可以扩展存储网络以跨 PowerStore T 型号 设备上的多个端口运行。 您将需要以下信息来执行扩展存储网络的步骤。 注: 下面的示例网络资源可用于在两个 Dell EMC PowerSwitch 系列 S4148 架顶式交换机上扩展添加存储服务中配置的存储网络。 如果您未配置本指南中所述的相同存储网络,请将示例资源替换为与您的环境匹配的值。 表. 30: 存储网络资源 网络资源 示例 存储网络名称 Storage_Network PowerStore T 型号 设备的 4 端口卡的端口。 注: 在两个节点上必须相同。 2 ToR 交换机 1 端口用线缆连接到底部节点 (A)。 2 ToR 交换机 1 端口用线缆连接到底部节点 (B)。 53 要扩展的存储网络的 VLAN ID。 200 IP 地址 192.168.2.
2 1 图 18: 用线缆连接其他端口 1. 将底部节点 (A) 的端口 2 连接到底部交换机 (1) 的端口 2。 2. 将顶部节点 (B) 的端口 2 连接到顶部交换机 (2) 的端口 53。 在 ToR 交换机上配置 VLAN 以下步骤提供了在两个 Dell PowerSwitch 系列 S4148 架顶式 (ToR) 交换机上配置 VLAN 的示例。 您可以在执行这些步骤之前或之后,用线缆将 PowerStore T 型号 设备节点连接到交换机。有关步骤,请参阅用线缆将节点连接到 ToR 交换机。 如果您已使用在其上创建了存储网络的 VLAN 配置了其他 ToR 交换机端口,则可以跳过此步骤。 请参阅存储网络资源,了解以下各项的列表: ● 扩展存储网络所需的网络资源 ● 以下步骤中使用的示例值 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3.
表. 31: 用于配置 ToR 交换机以扩展 iSCSI 存储网络的代码示例 Tor 交换机 1 configure terminal interface ethernet 1/1/2 switchport mode trunk switchport trunk allowed vlan 200 no shutdown exit ToR 交换机 2 configure terminal interface ethernet 1/1/53 switchport mode trunk switchport trunk allowed vlan 200 no shutdown exit 添加 IP 地址并将存储网络映射到端口 配置并用线缆连接架顶式 (ToR) 交换机以扩展存储网络后,您将需要在 PowerStore Manager 中添加 IP 地址并映射端口以进行扩展。 请参阅存储网络资源,了解以下各项的列表: ● 扩展存储网络所需的网络资源 ● 以下步骤中使用的示例值 1. 从 PowerStore Manager 中,转至设置 > 网络 > 网络 IP,然后选择存储选项卡。 2.
B 创建其他存储网络 本附录包含以下信息。 主题: • 新建存储网络 新建存储网络 您最多可以配置 32 个存储网络,并且节点上的 4 端口卡或 I/O 模块上的每个端口最多 8 个网络。 您将需要以下信息来执行创建新存储网络的步骤。 注: 可以在添加存储服务中所述的为原始存储网络配置的两个 Dell EMC PowerSwitch 系列 S4148 架顶式 (ToR) 交换机上使用以下 示例网络资源。如果您未使用本指南中所述的相同 Dell EMC PowerSwitch 系列 S4148 ToR 交换机,请将示例资源替换为与您的 环境匹配的值。 表. 32: 新的存储网络资源 网络资源 示例 存储网络名称 Storage_Network2 PowerStore T 型号 设备的 4 端口卡的端口。 注: 在两个节点上必须相同。 2 ToR 交换机 1 端口用线缆连接到底部节点 (A)。 2 ToR 交换机 1 端口用线缆连接到底部节点 (B)。 53 VLAN ID 210 网络掩码/前缀长度 24 网关 192.168.21.1 可选的全局 IP 地址 192.
1 2 图 19: 用线缆连接其他端口 1. 将底部节点 (A) 的端口 2 连接到底部交换机 (1) 的端口 2。 2. 将顶部节点 (B) 的端口 2 连接到顶部交换机 (2) 的端口 53。 在 ToR 交换机上配置存储网络 以下步骤提供了在两个 Dell PowerSwitch 系列 S4148 架顶式 (ToR) 交换机上配置存储网络的示例。 您可以在执行这些步骤之前或之后,用线缆将 PowerStore T 型号 设备节点连接到交换机。有关步骤,请参阅用线缆将节点连接到 ToR 交换机。 请参阅新存储网络资源,了解以下各项的列表: ● 添加新存储网络所需的网络资源 ● 以下步骤中使用的示例值 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3. 在 ToR 交换机 1 上配置存储网络。 interface vlan 210 description Storage_Network2 exit 4.
switchport trunk allowed vlan 210 no shutdown 5. 在 ToR 交换机 2 上使用端口 53 重复步骤 1。 表.
C 使用 ToR 交换机配置 PowerStore T 型号且无 VLT 互连 本附录包括以下信息: 主题: • 使用没有 VLT 的 ToR 交换机配置 PowerStore T 型号 的步骤 使用没有 VLT 的 ToR 交换机配置 PowerStore T 型号 的步 骤 以下是使用两个没有虚拟链路中继互连的架顶式交换机部署 PowerStore T 型号 所需的步骤。 在使用 ToR 交换机配置 Dell PowerSwitch 系列以进行部署中提供了配置 PowerSwitch 系列的以下步骤的特定代码示例。 与交换机建立终端会话。 验证交换机版本和许可。 对每个交换机重复步骤 1 和 2。 配置 OOB 管理交换机。 在 ToR 交换机上配置一般设置。 在交换机上配置生产 VLAN。 在 ToR 交换机上配置上行链路端口。 如果您尚未执行以下操作: a. 用线缆将 OOB 管理交换机连接到 PowerStore T 型号 基本存储模块节点 b. 用线缆将基本盘柜连接到 ToR 交换机 c. 用线缆将 ToR 交换机连接在一起 d. 用线缆将 ToR 交换机连接到核心上行链路 9.
D 其他 Dell EMC PowerSwitch 系列配置操作 本附录包含以下信息。 主题: • • • Dell EMC SmartFabric Services 将交换机重置为出厂设置 PowerStore T 型号 部署中使用的 PowerSwitch 系列的运行配置 Dell EMC SmartFabric Services Dell EMC SmartFabric Services 实现了端到端自动化构造,使高达 98% 的任务自动执行,从而为群集和网络扩展的第 2 天网络操作提 供了简易性和敏捷性。通过使用 vCenter 的单一管理窗格,用户可以从 vCenter 内操作和执行一个或多个构造的生命周期管理。 如果您有兴趣将 Dell EMC SmartFabric Services 应用到 PowerStore 网络部署,请参阅以下文档以了解更多信息。 表.
PowerStore T 型号 部署中使用的 PowerSwitch 系列的运 行配置 当 Dell PowerSwitch 系列 S4148 交换机用作管理和架顶式 (ToR) 交换机时,使用以下命令来生成运行配置文件: show running-configuration 管理交换机的运行配置示例 ! Version 10.4.1.4 ! Last configuration change at Mar 19 04:19:20 2020 ! snmp-server contact http://www.dell.com/support hostname powerstoreMgmtSwitch interface breakout 1/1/25 map 100g-1x interface breakout 1/1/26 map 100g-1x interface breakout 1/1/29 map 100g-1x interface breakout 1/1/30 map 100g-1x username admin password $6$rounds=656000$.
interface ethernet1/1/4 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/5 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/6 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/7 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/8 shutdown switchport access vlan 1 flowcontrol receiv
shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/17 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/18 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/19 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/20 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol t
flowcontrol transmit off ! interface ethernet1/1/30 no shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/31 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/32 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/33 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/34 shutdown switchpo
! interface ethernet1/1/42 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/43 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/44 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/45 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface ethernet1/1/46 shutdown switchport access vlan 1 flowcontrol
! interface ethernet1/1/54 shutdown switchport access vlan 1 flowcontrol receive off flowcontrol transmit off ! interface mgmt1/1/1 no shutdown no ip address dhcp ip address 100.0.100.50/24 ipv6 address autoconfig ! management route 0.0.0.0/0 100.0.100.1 ! support-assist 表. 35: ToR 交换机上的运行配置示例 交换机 1 ! Version 10.4.1.4 ! Last configuration change at Mar 19 04:24:55 2020 ! snmp-server contact http://www.dell.
表.
表.
表.
表.
表.
表.