Dell EMC PowerStore 데이터 보호 버전 2.
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2020 - 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC 및 기타 상표는 Dell Inc. 또는 그 자회사의 상표입니다. 다른 상표는 해당 소유자 의 상표일 수 있습니다.
목차 추가 리소스................................................................................................................................................................................. 4 장 1: 소개........................................................................................................................................ 5 데이터 보호...........................................................................................................................................................................
추가 리소스 제품군을 향상시키기 위한 노력의 일환으로 소프트웨어와 하드웨어의 개정 버전을 정기적으로 릴리스하고 있습니다. 이 문서에서 설 명하는 일부 기능은 현재 사용 중인 소프트웨어 또는 하드웨어의 일부 버전에서 지원되지 않을 수 있습니다. 제품 릴리스 노트에는 제 품 기능에 대한 최신 정보가 제공되어 있습니다. 제품이 올바르게 작동하지 않거나 이 문서에 설명된 대로 작동하지 않는 경우 서비스 공급업체에 문의하십시오. 지원 정보 지원, 제품 및 라이선스 정보는 다음과 같이 확인할 수 있습니다. ● 제품 정보 제품 및 기능 설명서 또는 릴리스 노트를 보려면 https://www.dell.com/powerstoredocs에서 PowerStore 설명서 페이지를 참조 바 랍니다. ● 문제 해결 제품, 소프트웨어 업데이트, 라이선스 등록 및 서비스에 대한 자세한 내용은 https://www.dell.com/support에서 해당 제품 지원 페 이지를 참조 바랍니다.
1 소개 이 장에서 다루는 내용은 다음과 같습니다. 주제: • • • • 데이터 보호 스냅샷 복제 보호 정책 데이터 보호 PowerStore는 로컬 데이터 보호와 원격 데이터 보호를 모두 제공합니다. PowerStore Manager를 사용하여 볼륨, 볼륨 그룹, 가상 머신 또는 파일 시스템의 스냅샷(point-in-time copy)을 생성하여 데이터를 로컬로 보호할 수 있습니다. 재해 발생 시 이중화를 위해 데이터 를 원격 시스템에 복제하여 원격 보호를 적용할 수도 있습니다. PowerStore를 사용하면 스냅샷 생성, 복제 또는 둘 모두에 대한 규칙 집합인 사용자 지정 보호 정책을 생성하고 이를 스토리지 리소 스에 할당할 수 있습니다. 보호 정책은 스토리지 리소스에 정의된 규칙을 적용하여 로컬 및/또는 원격 보호 기능을 제공합니다. 스냅샷 스냅샷은 볼륨, 볼륨 그룹, 가상 머신 또는 파일 시스템의 데이터에 대한 읽기 전용 point-in-time copy입니다.
복제 데이터 복제는 스토리지 데이터를 원격 시스템에 복제하는 프로세스로, 기본 프로덕션 시스템에 장애가 발생할 경우 우수한 중복성 을 제공합니다. 또한 시스템 장애의 다운타임 관련 비용을 최소화하고 자연 재해 또는 사용자 오류 후 복구를 간소화합니다. PowerStore는 볼륨 및 볼륨 그룹에 대한 비동기식 원격 복제를 지원합니다. 파일 시스템 또는 가상 볼륨에 대한 복제는 지원되지 않 습니다. 복제를 구성하려면 1. 소스 시스템과 대상 시스템 간의 원격 연결을 생성합니다. 2. 비즈니스 요구에 가장 적합한 복제 규칙을 사용하여 보호 정책을 구성합니다. 3. 스토리지 리소스에 보호 정책을 할당합니다. PowerStore를 사용하면 원격 시스템으로의 페일오버를 제어하고 원격 보호 세션의 방향을 반대로 전환할 수 있습니다. 다음과 같은 경우에 페일오버가 필요할 수 있습니다. ● 새 시스템으로 데이터를 마이그레이션하고 데이터 손실 없이 해당 클러스터에서 작업을 수행할 수 있는 경우.
2 스냅샷 이 장에서 다루는 내용은 다음과 같습니다. 주제: • • • • • 스냅샷 생성 씬 클론 생성 클론을 사용하여 호스트에서 읽기 전용 스냅샷에 액세스 스토리지 리소스 새로 고침 스토리지 리소스를 스냅샷으로 복원 스냅샷 생성 스냅샷을 생성하면 스토리지 리소스 및 그 안에 포함된 모든 파일과 데이터의 특정 시점 상태가 저장됩니다. 스냅샷을 사용하여 전체 스토리지 리소스를 이전 상태로 복원할 수 있습니다. 볼륨, 볼륨 그룹, 파일 시스템 또는 가상 머신의 스냅샷을 생성할 수 있습니다. 스냅샷을 생성하기 전에 다음 사항을 고려하십시오. ● 스냅샷은 원본 데이터의 전체 복제본이 아닙니다. 스냅샷을 미러, 재해 복구 또는 고가용성 툴로 활용하지 않는 것이 좋습니다. 스 냅샷은 스토리지 리소스의 실시간 데이터에서 부분적으로 파생되므로, 스토리지 리소스를 액세스할 수 없게 되면 스냅샷에 액세 스할 수 없게 될 수 있습니다. ● 스냅샷은 공간 효율적이지만 전체 시스템 스토리지 용량을 사용합니다.
● 백업에서 씬 클론 복원 ● 씬 클론에 보호 정책 적용 볼륨 또는 볼륨 그룹의 씬 클론을 생성하려면 다음을 수행합니다. 1. Storage > Volumes 또는 Storage > Volume Groups를 선택하여 관련 리소스 창을 엽니다. 2. 관련 볼륨 또는 볼륨 그룹 옆의 확인란을 클릭한 다음, Repurpose > Create Thin Clone using Volume(또는 볼륨 그룹의 경우 Create Thin Clone)을 선택합니다. 3. Create Thin Clone 슬라이드 창에서 다음을 수행합니다. ● 씬 클론 이름을 입력합니다. ● 설명을 입력합니다(선택 사항). ● 성능 정책을 설정합니다(볼륨에서 생성되는 씬 클론에만 해당). ● 호스트 접속 구성을 설정합니다(볼륨에서 생성되는 씬 클론에만 해당). ● 보호 정책을 설정합니다. 4. Clone을 클릭합니다. 스냅샷에서 씬 클론을 생성하려면 다음을 수행합니다. 1. 관련 스토리지 리소스 창을 엽니다. 2.
스냅샷에서 스토리지 리소스를 새로 고치려면 다음을 수행합니다. 1. 2. 3. 4. 5. 6. 7. 8. 관련 스토리지 리소스 목록 창을 엽니다. 스냅샷이 생성된 스토리지 리소스를 선택하여 해당 개요 창을 엽니다. Protection 탭을 클릭한 다음 Snapshots을 클릭합니다. 스냅샷 목록에서 새로 고침 작업에 사용할 스냅샷을 선택합니다. More Actions > Refresh using Snapshot을 클릭합니다. Refresh using Snapshot 슬라이드 패널의 Volume being refreshed 드롭다운 목록에서 새로 고칠 볼륨 또는 클론을 선택합니다. 새로 고친 볼륨의 백업 스냅샷을 생성할지 여부를 선택합니다 .이 옵션은 기본적으로 선택되어 있습니다. Refresh를 클릭합니다. 관련 볼륨을 사용하여 스토리지 리소스를 새로 고치려면 다음을 수행합니다. 1. 2. 3. 4. 5. 관련 스토리지 리소스 목록 창을 엽니다.
3 보호 정책 이 장에서 다루는 내용은 다음과 같습니다. 주제: • • • • • • 스냅샷 규칙 생성 복제 규칙 생성 보호 정책 생성 보호 정책 수정 스토리지 리소스에 보호 정책 할당 보호 정책 할당 취소 스냅샷 규칙 생성 스냅샷 생성 빈도와 스냅샷 보존 기간 같은 매개변수를 제어하는 스냅샷 규칙을 생성할 수 있습니다. 스냅샷 규칙을 복제 규칙과 함께 사용하면 데이터 보호 요구 사항에 따라 스토리지 리소스에 일관된 데이터 보호 정책을 구성하고 적용할 수 있습니다. 기존의 규칙 외에 새 스냅샷 규칙을 생성하려면 작업을 진행하기 전에 관리자와 함께 비즈니스 요구 사항을 먼저 검토하는 것이 좋습 니다. 이는 시스템 전반에서 일관된 정책을 확보하고 유지하는 데 도움이 됩니다. 새 스냅샷 규칙을 생성하려면 다음을 수행합니다. Protection > Protection Policies를 선택합니다.
3. Replication Rules 창에서 Create를 클릭합니다. 4. Create Replication Rule 슬라이드 패널에서 새 규칙의 이름을 입력합니다. 5. 다음을 설정합니다. ● 기존 복제 대상을 선택하거나 새 대상을 구성합니다. ● RPO를 설정합니다. ● alert threshold를 설정합니다. 6. Create를 클릭합니다. RPO(Recovery Point Objective) RPO(Recovery Point Objective)는 장애가 발생할 경우 손실될 수 있는 허용 가능한 데이터의 양이며, 시간 단위로 측정됩니다. 복제 규 칙을 설정할 때 RPO를 바탕으로 자동 동기화를 구성할 수 있습니다. 가능한 RPO 값의 범위는 5분에서 24시간 사이입니다. 기본 RPO 값은 1시간입니다. 노트: RPO 간격이 작을수록 더 많은 보호 기능을 제공하고 공간을 덜 소모합니다. 하지만 성능에 미치는 영향이 더 높기 때문에 네트워크 트래픽이 더 많이 발생합니다.
이 작업 정보 노트: 보호 정책의 설정을 변경하면 보호 정책이 할당된 모든 객체에 새 설정이 적용됩니다. 하나의 리소스에 대한 보호 정책을 변경해야 하는 경우에는 새 보호 정책을 생성하여 해당 리소스에 할당하는 것이 좋습니다. 하나 이상의 스토리지 리소스에 할당된 보호 정책에 사용되는 복제 규칙에서는 복제 대상을 변경할 수 없습니다. 다른 원격 시스템으 로 복제를 재구성하려면 보호 정책을 할당 취소하고 다른 복제 규칙을 사용하여 새 보호 정책을 할당합니다. 복제 규칙을 사용하여 보 호 정책을 할당 취소하면 연결된 복제 세션이 삭제되고, 새 보호 정책을 할당하면 새 대상과의 전체 동기화가 필요한 새 복제 세션이 생성됩니다. 단계 1. Protection > Protection Policies를 선택합니다. 2. 관련 정책 옆의 확인란을 선택하고 Modify를 클릭합니다. 3. Properties 슬라이드 패널에서 다음 매개변수를 수정할 수 있습니다.
노트: 가져오기 작업이 진행 중인 동안에는 보호 정책을 할당 취소할 수 없습니다. 단계 1. 보호 정책을 할당하려는 스토리지 리소스의 확인란을 선택합니다. 2. Protect > Unassign Protection Policy를 선택합니다. 3. Unassign을 클릭하여 확인합니다.
4 복제 이 장에서 다루는 내용은 다음과 같습니다. 주제: • • • 원격 시스템 Synchronization 페일오버 원격 시스템 원격 시스템 연결을 구성하여 소스 시스템과 대상 시스템 간의 원격 복제를 활성화할 수 있습니다. PowerStore에서 원격 시스템 연결 은 복제 규칙에 연결됩니다. 원격 시스템 연결은 복제 규칙을 생성하기 전에 미리 생성하거나 복제 규칙을 생성하는 동안 생성할 수 있습니다. 노트: 서로 다른 버전(1.x, 2.x)을 실행하는 시스템 간에 원격 연결을 생성할 수 있습니다. 원격 시스템 연결을 생성하기 전에 다음과 같은 원격 시스템 정보를 확보했는지 확인하십시오. ● 시스템 IP 주소 ● 시스템에 연결하기 위한 사용자 인증 자격 증명 원격 시스템 연결을 추가하려면 다음을 수행합니다. 1. Protection > Remote Systems를 선택합니다. 2. Remote Systems 창에서 Add를 클릭합니다. 3.
노트: 비동기식 복제 세션 중에 볼륨을 볼륨 그룹에 추가하거나 볼륨 그룹의 크기를 변경하면 변경 사항이 대상에 즉시 표시되지 않습니다. 수동 동기화를 수행하거나 RPO에 따라 동기화가 수행될 때까지 기다릴 수 있습니다. 복제 세션이 다음 상태에 있는 경우 동기화를 수행할 수 있습니다. ● 정상 작동 ● 시스템 일시 중지됨 복제 세션이 동기화되는 동안에는 다음과 같은 작업을 수행할 수 있습니다. ● ● ● ● 소스 시스템에서의 계획된 페일오버 대상 시스템에서의 페일오버 소스 또는 대상 시스템에서의 복제 세션 일시 중지 보호 정책을 제거하여 복제 세션 삭제 동기화에 실패하면 복제 세션이 시스템 일시 중지 상태로 전환됩니다. 시스템이 복구되면 복제 세션은 시스템이 일시 중지된 지점과 동일한 지점에서 다시 진행됩니다. 페일오버 복제 세션을 페일오버하면 소스 시스템과 대상 시스템 간의 역할이 전환되고 복제 세션의 방향이 반대로 전환됩니다. 페일오버에는 두 가지 유형이 있습니다.
● ● ● ● ● 볼륨 그룹 구성원 자격 변경 볼륨 그룹 크기 증가 볼륨 그룹 이름 변경 마이그레이션 시작 보호 정책 제거 노트: 소스 시스템에서 이러한 작업을 계속 수행할 수 있습니다. 페일오버 테스트가 진행 중인 경우 계획된 페일오버를 수행할 수 없습니다. 페일오버 테스트를 중지하여 계획된 페일오버를 수행합 니다. 하지만 계획되지 않은 페일오버가 재해 발생 시 중단 없이 계속 진행될 수 있습니다. 가능한 경우, 페일오버 테스트를 시작한 후 대상에 복제된 모든 데이터가 손실되기 때문에 계획되지 않은 페일오버 전에 페일오버 테스트를 중지하는 것이 좋습니다. 또한 페일오버 테스트 중에 복제 세션을 일시 중지하고 재개할 수 있습니다. 페일오버 테스트를 수행하는 동안 복제 세션을 삭제하면 테스트가 취소됩니다. 페일오버 테스트 시작 현재 대상 데이터 또는 모든 스냅샷에서 페일오버 테스트를 시작할 수 있습니다. 페일오버 테스트를 시작하는 방법에는 두 가지가 있습니다.
계획되지 않은 페일오버는 소스 시스템 장애 같은 이벤트 또는 소스 시스템에서 발생하는 이벤트 후에 수행되며, 이 경우 운영 액세스 에 대한 다운타임이 발생합니다. 계획되지 않은 페일오버는 대상 시스템에서 시작되고 동기화된 시점 스냅샷에서 원래 대상 리소스 에 대한 운영 액세스를 제공합니다. 소스 시스템에 대한 연결이 다시 설정되면 원래 소스 리소스가 대상 모드로 전환됩니다. 계획되지 않은 페일오버 후에는 최신 데이터 또는 모든 시점 스냅샷에서 시스템을 복구할 수 있습니다. 대상 스토리지 리소스를 동기화하고 복제 세션을 재개하려면 복제 세션을 재보호하십시오.
A 활용 사례 이 장에서 다루는 내용은 다음과 같습니다. 주제: • • 스냅샷 및 씬 클론 활용 사례 복제 활용 사례 스냅샷 및 씬 클론 활용 사례 스냅샷 및 씬 클론을 사용하여, 손상된 볼륨을 복원하고 테스트 환경을 생성할 수 있습니다. 스냅샷은 객체의 현재 상태를 저장하는 데 사용할 수 있는 읽기 전용 복사본입니다. 손상 또는 사용자 오류가 발생한 경우 스냅샷을 사용하여 데이터를 신속하게 복구할 수 있습니다. 스냅샷은 호스트에서 직접 액세스할 수 없습니다. 씬 클론은 스냅샷, 볼륨 또는 볼륨 그룹의 쓰기 가능 복사본으로서, 호스트에서 액세스할 수 있습니다. 씬 클론은 상위 객체의 복사본 으로 직접 생성하거나 기존 스냅샷 중 하나를 사용하여 생성할 수 있습니다. 스냅샷과 씬 클론은 모두 데이터 블록을 상위 객체와 공 유하는 공간 효율적인 복사본입니다.
클러스터 간 마이그레이션 스토리지 객체를 다른 PowerStore 클러스터로 마이그레이션해야 할 경우에는 두 클러스터 간에 일회성 복제를 설정한 다음 새 클러 스터에 계획된 페일오버를 수행하여 마이그레이션을 완료할 수 있습니다. 마이그레이션 후 소스 객체를 해체한 뒤 원래 클러스터에 서 공간을 재요청하십시오. 계획된 다운타임에 복제 사용 계획된 다운타임은 유지 보수 또는 테스트를 위해 소스 시스템을 오프라인으로 전환한 채로 대상 시스템에서 작업을 수행하는 경우 입니다. 계획된 다운타임 전에는 소스와 대상 모두 액티브 상태의 복제 세션으로 실행되고 있습니다. 계획된 다운타임에는 데이터 손 실이 없습니다. 이 시나리오에서 소스 시스템인 보스턴이 유지 보수를 위해 오프라인으로 전환되고, 대상 시스템인 뉴욕은 유지 보수 기간 동안 운영 시스템으로 사용됩니다. 유지 보수가 완료되면 운영을 보스턴 시스템에 반환합니다. 계획된 다운타임을 시작하려면 보스턴 소스 시스템에서 Planned Failover를 선택합니다.