Dell EMC PowerStore Configurando compartilhamentos SMB 2.x Junho 2021 Rev.
Notas, avisos e advertências NOTA: Uma NOTA indica informações importantes que ajudam você a usar melhor o seu produto. CUIDADO: um AVISO indica possíveis danos ao hardware ou a possibilidade de perda de dados e informa como evitar o problema. ATENÇÃO: uma ADVERTÊNCIA indica possíveis danos à propriedade, lesões corporais ou risco de morte. © 2020- 2021 Dell Inc. ou suas subsidiárias. Todos os direitos reservados. Dell, EMC e outras marcas comerciais são marcas comerciais da Dell Inc.
Índice Outros recursos..............................................................................................................................4 Capítulo 1: Visão geral..................................................................................................................... 5 Suporte do SMB.................................................................................................................................................................... 5 Considerações sobre planejamento......
Prefácio Como parte de um esforço contínuo de melhorias, lançamos periodicamente revisões de seu software e hardware. Algumas das funções descritas neste documento não são compatíveis com todas as versões de software ou hardware usadas no momento. As notas da versão do produto contêm as informações mais recentes sobre os recursos do produto. Entre em contato com seu fornecedor se um produto não funcionar adequadamente ou conforme descrito neste documento.
1 Visão geral Este capítulo inclui as seguintes informações. Tópicos: • • Suporte do SMB Considerações sobre planejamento Suporte do SMB O Modelo PowerStore T é compatível com SMB 1 até SMB 3.1.1. Quando o suporte para SMB está habilitado no servidor NAS, você pode criar file systems habilitados para SMB. O servidor NAS com suporte para SMB pode ser independente ou associado a um domínio do Active Directory.
A criação de VLANs de rede e endereços IP é opcional para servidores NAS. Se você planeja criar uma VLAN para servidores NAS, ela não pode ser compartilhada com as redes de armazenamento ou de gerenciamento do Modelo PowerStore T. Além disso, reserve os recursos de rede e configure a rede no switch junto com o administrador de rede. Consulte os detalhes em Guia de Sistema de Rede do PowerStore para os Modelos PowerStore T.
2 Criar servidores NAS Este capítulo inclui as seguintes informações. Tópicos: • • • Visão geral da configuração de servidores NAS Criar servidor NAS para file systems SMB (somente Windows) Alterar as configurações do servidor NAS Visão geral da configuração de servidores NAS Para que você possa provisionar o armazenamento em arquivo no equipamento Modelo PowerStore T, um servidor NAS deve estar em execução no sistema.
Tela do assistente Descrição NOTA: Se você selecionar tanto o protocolo SMB quanto o NFS, habilitará automaticamente o servidor NAS para dar suporte a vários protocolos. A configuração multiprotocolo não está descrita neste documento. Windows Server Settings Selecione Standalone para criar um servidor SMB independente ou Join to the Active Directory Domain para criar um servidor SMB membro do domínio.
6. Na guia Segurança: ● Selecione Kerberos para adicionar o realm do AD (Active Directory) para autenticação Kerberos ou para configurar um realm Kerberos personalizado. ● Selecione Antivirus para ativar ou desativar o serviço de antivírus e para recuperar ou carregar o arquivo de configuração do antivírus.
3 Recursos adicionais de servidor NAS Este capítulo inclui os tópicos a seguir. Tópicos: • • • • Configurar o protocolo de compartilhamento FTP ou SFTP Configurar redes do servidor NAS Habilitar a proteção e eventos de NDMP Configurar a segurança do servidor NAS Configurar o protocolo de compartilhamento FTP ou SFTP Você pode configurar o FTP ou FTP sobre SSH (SFTP) depois que o servidor NAS tiver sido criado. Pré-requisitos Não há suporte para o modo FTP passivo.
Configurar interfaces de file para um servidor NAS Você pode configurar as interfaces de file para um servidor NAS depois que o servidor for adicionado ao PowerStore. Sobre esta tarefa Você pode adicionar mais interfaces de file e definir qual é a preferencial a ser usada. Além disso, você pode definir qual interface usar para produção e backup ou para IPv4 ou IPv6. Etapas 1. Selecione Storage > NAS Servers > [nas server]. 2. Clique em Add para adicionar outra interface de file ao servidor NAS. 3.
Sobre esta tarefa O NDMP é realizado após a criação do servidor NAS. O PowerStore é compatível com: ● NDMP de três vias. Os dados são transferidos via DMA por uma rede local (LAN) ou por uma rede de longa distância (WAN). ● Backups completos e incrementais. Etapas 1. Selecione Storage > NAS Servers > [nas server] > Protection and Events . 2. Em NDMP Backup, se a opção Disabled estiver ativada, deslize o botão para mudar para Enabled. 3. Digite uma senha em New Password. O nome de usuário sempre é ndmp. 4.
armazenarem arquivos infectados no servidor e oferece proteção em caso de abertura de arquivos infectados. Essa solução antivírus consiste em uma combinação de software de sistema operacional, agente CAVA e um mecanismo antivírus de terceiros. O software CAVA e o mecanismo antivírus de terceiros devem ser instalados em um Windows Server no domínio. Para as versões do CEE CAVA necessárias para o PowerStore, consulte o Notas da versão do PowerStore.
4 Criar file systems e compartilhamentos SMB Este capítulo inclui os tópicos a seguir. Tópicos: • • Criar um file system Criar um compartilhamento SMB Criar um file system Para que você possa criar um compartilhamento SMB, é necessário criar um file system no servidor NAS. Pré-requisitos Certifique-se de que existe um servidor NAS configurado para dar suporte ao protocolo SMB, conforme descrito em Configurando servidores NAS. Etapas 1. Selecione Storage > File Systems e clique em Create. 2.
Opção Descrição para proteção de snapshots e de replicação, o PowerStore implementará a política de snapshot no file system e ignorará a política de replicação para o file system. Resumo Analise o resumo. Volte e faça as atualizações necessárias. 3. Clique em Create File System. O file system é exibido na lista de file systems e, se você tiver criado um compartilhamento SMB, ele será exibido na lista de compartilhamentos SMB.
Tabela 2. Configurações avançadas de file system para SMB (continuação) Configuração Descrição Notificar durante acesso ativada Habilite a notificação quando um file system for acessado. Por padrão, está opção é desabilitada. Habilitar publicação de eventos SMB Habilite o processamento de eventos SMB (Server Message Block) para esse file system. Criar um compartilhamento SMB Você pode criar um compartilhamento SMB em um file system que tenha sido criado com um servidor NAS habilitado para SMB.
Tabela 3. Propriedades de SMB avançadas Opção Descrição Disponibilidade contínua Permite o acesso contínuo e transparente dos aplicativos host a um compartilhamento após um failover do servidor NAS no sistema (com o estado interno do servidor NAS salvo ou restaurado durante o processo de failover). NOTA: Permita a disponibilidade contínua para o compartilhamento somente quando quiser usar clients de protocolo do SMB 3.0 (Microsoft Server Message Block) com o compartilhamento específico.
5 Mais recursos de file system Este capítulo inclui as seguintes informações. Tópicos: • Cotas do File system Cotas do File system Você pode controlar e limitar o consumo de espaço em unidade por meio da configuração de cotas para file systems no nível de diretório ou file system. Você pode habilitar ou desabilitar cotas a qualquer momento, mas recomenda-se que você as habilite ou desabilite durante o horário de produção fora de pico para evitar impacto nas operações do file system.
Tabela 5. Limites flexíveis e rígidos (continuação) Type Descrições O usuário é alertado quando o limite flexível é atingido, até o término do período de tolerância. Depois disso, uma condição de falta de espaço é atingida até o usuário voltar para o limite flexível. Quota Grace Period O recurso Quota Grace Period permite definir um período de tolerância específico para cada cota de árvore em um file system.
Adicionar uma árvore de cotas a um file system Sobre esta tarefa Crie uma árvore de cotas no nível do diretório de um file system para limitar ou monitorar o espaço de armazenamento total consumido por esse diretório. Etapas 1. Selecione Storage > File Systems > [file system] > Quotas > Tree Quotas. 2. Selecione Adicionar. 3. Deslize Enforce User Quota para a direita para ativar os valores padrão de User Quota em Tree Quota. 4. Especifique as informações solicitadas.