Dell EMC PowerStore PowerStore X 型号的网络连接指南 版本 2.x 6 月 2021 年 Rev.
注意、小心和警告 注: “注意”表示帮助您更好地使用该产品的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告: “警告”表示可能会导致财产损失、人身伤害甚至死亡。 © 2020 年 - 2021 年 Dell Inc. 或其子公司。保留所有权利。Dell、EMC 和其他商标是 Dell Inc.
目录 其他资源.........................................................................................................................................5 章 1: 概述........................................................................................................................................ 6 PowerStore X 型号 设备概述............................................................................................................................................. 6 支持的交换机..................................................
章 8: PowerStore X 型号 设备的初始配置.......................................................................................... 41 初始配置向导....................................................................................................................................................................... 41 获取填写好的初始配置工作表......................................................................................................................................... 42 附录 A: 扩展存储网络以跨多个端口运行.......................................
序言 为了不断改进,我们将定期发布软件和硬件产品的修订版。本文档中介绍的一些功能可能不被当前使用的软件或硬件的所有版本支 持。本产品发行说明提供了有关产品功能的新信息。如果某产品不能正常运行或其功能与本文档的描述不符,请与您的服务提供商 联系。 从何处获得帮助 可以按如下方式获取支持、产品和许可信息: ● 产品信息 有关产品和功能的文档或发行说明,请访问 PowerStore 文档页面,地址为 https://www.dell.com/powerstoredocs。 ● 故障排除 有关产品、软件更新、许可和服务的信息,请转到 https://www.dell.com/support,并找到相应的产品支持页面。 ● 技术支持 如需技术支持,如有服务请求,请转至 https://www.dell.
1 概述 本章包含以下信息。 主题: PowerStore X 型号 设备概述 支持的交换机 • • PowerStore X 型号 设备概述 PowerStore X 型号 支持已在系统中安装虚拟机管理程序的数据块(仅限 SAN)和 vVol 工作负载。系统软件部署在虚拟机管理程序 上,使虚拟机 (VM) 和客户应用程序可以在硬件内部署。 PowerStore X 型号 型号: ● ● ● ● ● 1000X 3000X 5000X 7000X 9000X 注: 此型号不支持文件(网络连接存储 (NAS))服务。PowerStore T 型号 设备支持文件服务。 支持文档 除了通读本文档,您还应在配置交换机和网络之前通读以下指南: ● PowerStore 快速入门指南 ● PowerStore 规划指南 ● PowerStore 硬件信息指南 支持的交换机 PowerStore 可与以下运行 OS10 企业版 (OS10EE) 的 Dell EMC PowerSwitch 系列共同购买。 ● S4148F-ON ● S4148T-ON ● S5248F-ON 本指南的规划和要求部分可用于准备使
表. 1: PowerSwitch 文档资源 (续) 文档 参考 OS10 Enterprise Edition 用户指南 包含安装操作系统、远程访问交换机和运行 交换机命令所需的步骤。 位置 https://www.dell.com/support/home/us/en/04/ product-support/product/networking-s4148f-on/ docs 对于 Dell EMC S5248F-ON 交换机,请转到 PowerSwitch S5248F-ON 文档页面,网址: https://www.dell.
2 准备配置交换机和网络 本章包含以下信息。 主题: PowerStore X 型号 网络设置准备工作表 初始配置工作表 • • PowerStore X 型号 网络设置准备工作表 与网络管理员一起填写网络设置准备工作表,以保留配置交换机所需的信息。 在填写网络设置准备工作表时,还建议您与网络管理员一起填写初始配置工作表。 有关为 Dell EMC PowerSwitch 系列 S4148-ON 交换机填写的网络设置准备工作表的示例,请参阅填写好的 PowerStore X 型号 网络设 置准备工作表示例。 表. 2: PowerStore X 型号 网络设置准备工作表(空白) 步骤 步骤详细信息 注释 1. 打印此表以记录保留的资源。 2. 打印初始配置工作表 以记下您首次创建群集时在 PowerStore X 型号中创建网络将需要的其他网络资源。 3.
表. 2: PowerStore X 型号 网络设置准备工作表(空白) (续) 步骤 步骤详细信息 注释 默认网关 NTP 服务器 8. Dell EMC 支持使用两个具有第 2 层互连链路的架顶 (ToR) 交换机部署 PowerStore X 型号。 选择您将使用哪一类型的第 2 层互连: 极力建议:多机箱链路聚合组 (MC-LAG) 如果您将使用 MC-LAG,请记录将用于将交换机连接在一起的端口。 交换机到交换机端口对 1 交换机到交换机端口对 2 或者,不使用 MC-LAG 的 L2 上行链路 9. 如果使用 MC-LAG,请输入域 ID。 10 如果对第 2 层互连使用 VLT,请记录以下各项: 将用于交换机 1 和交换机 2 的 VLT MAC 地址。 对交换机 1 和交换机 2 使用相同的 VLT MAC 地址。 注: 对于 VLT MAC 地址,不可以使用全零 (00:00:00:00:00)。 交换机 1 的 VLT 优先级 交换机 2 的 VLT 优先级 11.
初始配置工作表 与网络管理员一起填写初始配置工作表。填写后,该工作表将在 PowerStore X 型号 的初始配置期间提供设置网络所需的信息。 在填写初始配置工作表时,还建议您与网络管理员一起填写网络设置准备工作表。 有关已填写的初始配置工作表的示例,请参阅填写好的 PowerStore X 型号 初始配置工作表示例。 表.
表.
表.
3 PowerStore X 型号:网络配置要求 本章包含下列信息。 主题: • • • • 架顶式 (ToR) 交换机连接选项和要求 PowerStore X 型号 网络 PowerStore X 型号 网络 VLAN 选项 网络配置的 IP 地址 架顶式 (ToR) 交换机连接选项和要求 PowerStore 需要连接到一对架顶式 (ToR) 交换机。 本节介绍以下各项的要求: ● 交换机到交换机 (L2) 连接 ● 节点到 ToR 交换机连接 架顶式 (ToR) 交换机到 ToR 交换机 (L2) 连接选项 使用以下选项之一将两个 ToR 交换机连接在一起。 表. 4: ToR 交换机到 ToR 交换机互连选项 交换机互连选项 建议 1. 多机箱链路聚合组 (MC-LAG) 戴尔强烈建议使用 MC-LAG 来实现交换机之间的连接。 2.
PowerStore Network Topology with Top of Rack Switches and MC-LAG Interconnect Upstream Switch 2 Upstream Switch 1 Port Channel Top of Rack Switch 1 Port 0 MC-LAG Interconnect Port 1 Top of Rack Switch 2 Port 1 Node A Node B PowerStore T Appliance Legend: 图 1: 使用 MC-LAG 互连的 ToR 交换机 14 Port 0 PowerStore X 型号:网络配置要求 10 Gb 1 Gb
注: 可靠的高速上行链路的端口位置可能会因交换机供应商或型号而异。 MC-LAG 是一种交换机互连技术,可将大量独立的架顶式 (ToR) 交换机加入单个虚拟机箱。MC-LAG 允许链路聚合 (LAG) 端口组涵 盖多个机箱,从而实现 LAG 连接的更强恢复能力。此外,MC-LAG 允许交换机之间的流量使用可用连接的全部带宽,而无需使用生 成树协议 (STP),该协议会禁用一些链路来防止形成环路。 MC-LAG 是此技术的通用名称,但某些供应商使用自己的专有术语来定义 MC-LAG 连接。 表.
PowerStore Network Topology with a no MC-LAG interconnect Upstream Switch 2 Upstream Switch 1 Port Channels Top of Rack Switch 1 Port 0 Top of Rack Switch 2 Port 1 Port 1 Node A Node B PowerStore T Appliance Legend: 图 2: 使用非 MC-LAG L2 互连的 ToR 交换机 16 Port 0 PowerStore X 型号:网络配置要求 10 Gb 1 Gb
注: 可靠的高速上行链路的端口位置可能会因交换机供应商或型号而异。 非 MC-LAG L2 连接需要冗余的高速连接。 节点与架顶式 (ToR) 交换机的连接 使用架顶式 (ToR) 交换机进行部署时,要求每个基本存储模块设备节点与每个 ToR 交换机至少有一个连接,以便在 NIC 和交换机级 别提供冗余。 图 3: 节点与 ToR 交换机之间的布线 在用缆线将节点与交换机连接时: ● 同一节点上的端口 0 和端口 1 必须连接到相反的交换机 ● 节点 A 上的端口 0 和节点 B 上的端口 0 必须连接到相反的交换机 ● 节点 A 上的端口 1 和节点 B 上的端口 1 必须连接到相反的交换机 PowerStore X 型号:网络配置要求 17
PowerStore X 型号 网络 PowerStore X 型号 要求所有网络都是唯一的。强烈建议使用多个唯一的 VLAN 部署 PowerStore X 型号,以分离流量。但是,如果只 有一个可用 VLAN,您可以选择使用单个 VLAN 和多个唯一子网部署 PowerStore X 型号,如下图所示。 图 4: PowerStore X 型号 网络流量 确保 PowerStore X 型号 接口可以通过上面所示的 VLAN 相互通信。请参考您的网络供应商文档,确保所有正常的 L2 和/或 L3 流量 均在 PowerStore X 型号 利用的所有网络中适当路由。 表.
PowerStore 中的网络配置 所有 PowerStore 网络都必须在交换机上配置。在您首次通过 PowerStore Initial Configuration Wizard (ICW) 创建群集时,即在 PowerStore 中配置了管理、存储和 vMotion 网络。 PowerStore X 型号:网络配置要求 19
PowerStore X 型号 网络 VLAN 选项 下表显示了在 PowerStore X 型号 设备中不同类型的网络示例,及其示例 VLAN ID。 表. 7: PowerStore X 型号 VLAN 配置 示例 VLAN ID 网络 VLAN 端口 子网示例 1 远程发现(通过本机 VLAN 运行) 无标记 169.254.x.x/16 100 管理 已标记 y.y.y.y/24 200 存储 已标记 y.y.x.y/24 400 vMotion 已标记 y.y.a.y/24 1 内部(通过本机 VLAN 运行) 无标记 内部 IPv6 寻址 无标记流量 如果您想要将本机 VLAN 用于任何 PowerStore 网络,则必须在 PowerStore 初始配置向导中为任何无标记流量输入 VLAN ID 0 (零)。PowerStore 使用 VLAN 0 作为无标记流量的标签。当您将 VLAN ID 设置为零时,网络流量不会进行标记(基于 802.
表.
4 使用 Dell EMC PowerSwitch 系列 S4148-ON 交 换机进行配置 本章包含下列信息。 主题: 使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机进行配置的概述 获取填写好的网络设置准备工作表 与交换机建立终端会话 验证交换机版本和许可 在架顶 (ToR) 交换机上配置常规设置 交换机上配置 PowerStore X 型号网络 VLAN 配置虚拟链路中继互连 (VLTi) 配置架顶 (ToR) 交换机上的上行链路端口 • • • • • • • • 使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机进行 配置的概述 本文档介绍通过单个群集为 PowerStore X 型号 配置 Dell EMC PowerSwitch 系列 S4148-ON 架顶式交换机的步骤,该群集包含一个具 有单个基本存储模块的设备。 如果您不打算使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机部署 PowerStore,请参阅 PowerStore 第三方交换机简单支持矩 阵,以查看受支持交换机的列表。第三方交换机简单
表. 9: 网络设置准备工作表(已填写) (续) 步骤 步骤详细信息 注释 节点 B,端口 0 到 ToR 2 端口 54 节点 B,端口 1 到 ToR 1 端口 54 3. 记录在配置交换机时用于发现的交换机端口。 端口 13 4. 记录将用于系统管理的 VLAN ID: 5. 6. 7. 远程发现(无标记) 1 管理(有标记) 100 记录将用于生产的 VLAN ID: 存储网络(有标记) 200 vMotion(有标记) 400 内部(无标记) 1 保留并记录配置以下交换机所需的 IP 地址: 交换机 1 的管理 IP 地址 100.0.100.10/24 交换机 2 的管理 IP 地址 100.0.100.11/24 默认网关 100.0.100.1 NTP 服务器 100.0.100.
表. 9: 网络设置准备工作表(已填写) (续) 步骤 步骤详细信息 注释 MC LAG 只需要单个端口通道 ID。 或者,记录不使用 MC-LAG 的 L2 上行链路所需的上行链路端口通道 ID。 不使用 MC-LAG 的 L2 上行链路连接需要两个端口通道 ID。 12. 1. 不使用 MC-LAG 的 L2 上行链路的端口通道 ID 不适用 2. 不使用 MC-LAG 的 L2 上行链路的端口通道 ID 不适用 作为最佳做法,建议将生成树协议添加到 ToR 交换机。记录要在每个交换机上设置的生成树协议。 ToR 交换机 1 的生成树协议 40960 ToR 交换机 2 的生成树协议 45056 13. 完成上述步骤后,您就具备了配置交换机所需的信息。现在,继续与网络管理员合作,填好初始配置工作表,以确保: ● 交换机上的网络配置与将在 PowerStore X 型号 中完成的网络配置保持一致。 ● 您保留必要的网络资源,以便完成 PowerStore X 型号网络的部署。 14.
5. 使用终端仿真程序连接到交换机。 6. 输入交换机登录凭据。默认用户名和密码为: ● 用户名:admin ● 密码:admin 7. 进入全局配置模式。 configure terminal 8. 建议您在首次登录交换机后更改密码。使用以下命令更改交换机密码。 username admin password role sysadmin 验证交换机版本和许可 在配置交换机和网络之前,请检查交换机操作系统的版本和许可。 如果您需要升级交换机操作系统或者重新安装交换机许可证,请参阅 OS10 Enterprise Edition 用户指南 了解详细信息。 1. 建立到交换机的终端连接,并在连接后按 Enter 键。 2. 运行命令 show version 以显示操作系统版本。Dell EMC 建议升级至 Dell Digital Locker (www.dell.
在架顶 (ToR) 交换机上配置常规设置 执行以下步骤,在 ToR 交换机上配置常规设置。 在 OS10EE 中,LLDP(链路层发现协议)默认已在每个接口上全局启用。您可以使用 LLDP 进行故障排除和验证。建议您在交换机 上启用 LLDPU(链路层发现协议数据单元)中的所有可选 TLV(类型、长度、值)。 1. 建立到第一个 ToR 交换机 (Switch1) 的终端连接 2. 进入全局配置模式。 configure terminal 3. 为交换机配置主机名。 hostname Switch1 4. 如果执行远程发现,可选择在交换机上为远程发现工作站配置以太网接口。 注: 在配置交换机 2 时,您不需要执行此步骤。 interface ethernet 1/1/13 description discoveryWorkstation switchport access vlan 1 no shutdown 5.
交换机 1 交换机 2 configure terminal configure terminal hostname Switch1 hostname Switch2 interface ethernet 1/1/13 description discoveryWorkstation switchport access vlan 1 no shutdown interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.11/24 exit interface mgmt 1/1/1 no shutdown no ip address dhcp ip address 100.0.100.10/24 exit management route 0.0.0.0/0 100.0.100.1 ntp server 100.0.1000.200 management route 0.0.0.0/0 100.0.100.
7.
7. 设置交换机的优先级。 primary-priority 1 有效的优先级值范围为 1 到 65535。优先级设置较低的交换机将优先于具有较高优先级值的交换机。不要为两个 ToR 交换机设置 相同的优先级值。 8. 输入 VLT MAC 地址以避免网络冲突。 注: 对于 VLT MAC 地址,不可以使用全零 (00:00:00:00:00)。 vlt-mac 00:00:00:00:00:01 在配置交换机 2 时使用相同的 VLT MAC 地址。 9. 对第二个交换机重复这些步骤。 在重复这些步骤时,调换步骤 1 和 5 中的交换机 IP 地址,如下面的代码示例所示。 表. 11: VLTi 配置步骤的代码示例 交换机 1 交换机 2 configure terminal interface range ethernet 1/1/25-1/1/26 description vtli no switchport exit vlt-domain 1 discovery-interface ethernet 1/1/25-1/1/26 backup destination 100.0.100.
注: 对于 iSCSI 最佳做法,建议按如下所示禁用流控制。 configure terminal interface ethernet 1/1/54 description Node-B-Port-1 no shutdown switchport mode trunk switchport access vlan 1 switchport trunk allowed vlan 100,200,400 flowcontrol receive off flowcontrol transmit off spanning-tree port type edge exit 5. 对交换机 2 与节点 A 端口 0 和节点 B 端口 1 的连接重复这些步骤。 在配置交换机 2 时,请注意以太网接口已反转。以太网接口 1 是在 Node-B-Port-1 上配置的,接口 54 是在 Node-A-Port-0 上配置 的,如下所示。 表.
switchport trunk allowed vlan 100,200,400 vlt-port-channel 30 4. 配置交换机上的上行链路端口。 注: 对于 iSCSI 最佳做法,建议按如下所示禁用流控制。 interface ethernet 1/1/29 description Uplink_Ports no shutdown channel-group 30 mode active no switchport flowcontrol receive off flowcontrol transmit off interface ethernet 1/1/30 description Uplink_Ports no shutdown channel-group 30 mode active no switchport flowcontrol receive off flowcontrol transmit off 5. 将配置提交到 nvram。 copy running-configuration startup-configuration 6.
5 PowerStore X 型号:将设备连接到交换机 本章包含以下信息。 主题: 用线缆将基本盘柜连接到 ToR 交换机 用线缆将 ToR 交换机连接在一起 用线缆将架顶交换机连接到核心上行链路 • • • 用线缆将基本盘柜连接到 ToR 交换机 用线缆将节点连接到架顶 (ToR) 交换机。 2 4 1 图 5: 基本盘柜与 ToR 交换机的连接 如示意图中所示,在将节点连线到 ToR 交换机时: ● 同一节点上的端口 0 和端口 1 必须连接到相反的交换机 ● 节点 A 上的端口 0 和节点 B 上的端口 0 必须连接到相反的交换机 ● 节点 A 上的端口 1 和节点 B 上的端口 1 必须连接到相反的交换机 表.
用线缆将 ToR 交换机连接在一起 使用 VLT 的 PowerStore 双交换机部署要求用线缆将两个架顶式 (ToR) 交换机连接在一起。 1 2 图 6: 交换机到交换机连接 使用两根支持高速端口之间连接的线缆,例如 100Gbps 直接连接线缆 (DAC)。 建议您对顶部和底部交换机上的 VLTi 对使用相同的端口号。 表.
用线缆将架顶交换机连接到核心上行链路 用线缆将 Dell EMC PowerSwitch 系列 S4148-ON 架顶式 (ToR) 交换机连接到核心上行链路。 Core uplinks Uplink A 1 3 Uplink B 4 2 图 7: Dell EMC PowerSwitch 系列 S4148-ON ToR 交换机连接到核心上行链路 表.
6 验证交换机和网络配置 本章包含以下信息。 主题: • • 验证架顶 (ToR) 交换机上的配置 Network Validation Tool for PowerStore 验证架顶 (ToR) 交换机上的配置 在您配置 Dell EMC PowerSwitch 系列 S4148-ON ToR 交换机并完成布线后,请在发现 PowerStore X 型号 型号部署之前验证配置。 1. 与交换机建立终端会话。 2. 验证接口状态。 show interface status | grep up Port Eth 1/1/1 Eth 1/1/13 Eth 1/1/25 Eth 1/1/26 Eth 1/1/29 Eth 1/1/30 Eth 1/1/54 Description Node-A-Port-0 discoveryWork..
5.
VLT VLAN mismatch: No mismatch 9. 验证 VLT 端口配置。 show vlt vlt-port-detail vlt-port-channel ID : 30 VLT Unit ID Port-Channel Status Configured ports Active ports ------------------------------------------------------------------------------1 port-channel30 up 2 2 * 2 port-channel30 up 2 2 10.
7 发现 PowerStore 设备 配置好网络并完成设备的安装后,您可以发现 PowerStore 设备并开始初始配置过程。 主题: • • 通过直接连接发现 通过远程连接发现 通过直接连接发现 这是建议步骤,要求您亲临安装了基本存储模块的数据中心或实验室。 ● (可选)下载并运行 PowerStore 网络验证工具 (NVT),验证您的网络是否已正确配置。可从 Dell EMC Central Solutions 下载 NVT,网址为:https://psapps.emc.com/central/solutions。 ● 确保工作站的网络适配器配置如下: ○ 直接连接到节点 A 上的 PowerStore 服务端口。 ○ 在服务 LAN 网络 (128.221.1.0/24) 上配置静态 IP 地址,且未定义网关地址(128.221.1.249;255.255.255.0;无网关) ○ 能够 ping 通节点 A 服务 LAN 端口 (128.221.1.250) 的 IP 地址 1.
通过远程连接发现 Network Node 如果您无法接触到基本存储模块,请在与 PowerStore 系统相同的网络上部署一个工作站或虚拟机,并使用 PowerStore 发现实用程 序来发现和创建群集。 B A 图 9: PowerStore X 型号 远程发现连接 有两种发现方法可供选择: ● 使用发现工具进行远程发现 ● 使用静态 IP 地址进行远程发现 使用发现工具进行远程发现 您可以使用发现工具来发现 PowerStore,该工具会广播一个 169.254.xx/16 IP 地址。 ● (可选)下载并运行 PowerStore 的网络验证工具 (NVT),验证您的网络是否已正确配置。可从 Dell EMC Central Solutions 下载 NVT,网址为:https://psapps.emc.
注: 为避免 IP 地址重复,请确保您设置了 169.254.x.x IP 地址的本机/未标记网络中只有一台笔记本电脑或虚拟机。 1. 在工作站或虚拟机中,打开网页浏览器,然后输入为访问 PowerStore Discovery Utility 而保留的任一 IP 地址。 ● http://169.254.0.10 ● http://169.254.0.20 ● http://169.254.0.30 ● http://169.254.0.40 ● http://169.254.0.50 2.
8 PowerStore X 型号 设备的初始配置 本章包含以下信息。 主题: • • 初始配置向导 获取填写好的初始配置工作表 初始配置向导 发现 PowerStore X 型号 设备后,会将您重定向到初始配置向导(ICW) 来配置 PowerStore X 型号 设备上的网络。 初始配置向导(ICW) 会提示您输入 PowerStore X 型号 设备的初始配置所需的网络信息。 在运行 ICW 时,请参阅填写好的初始配置工作表。初始配置工作表中应已填写了完成 PowerStore X 型号 设备的初始部署所需的所 有信息。 在运行 ICW 时,请注意以下事项: ● 登录凭据 首次登录 PowerStore 时,您将使用默认用户名和密码。但是,您必须先更改管理员密码,然后才能继续完成初始配置向导 (ICW)。请务必在填写好的初始配置工作表中记下您为群集输入的新管理员密码。尚未为您提供此密码的示例。 ● 本机 VLAN 如果您想要将本机 VLAN 用于任何 PowerStore 网络,则必须在 PowerStore 初始配置向导中为任何无标记流量输入 VLAN ID 0 (零)。PowerStore 使
获取填写好的初始配置工作表 初始配置向导(ICW) 会提示您输入 PowerStore X 型号 设备的初始配置所需的网络信息。在配置 PowerStore X 型号 网络的步骤中使 用下面的工作表中所提供的网络资源。 以下工作表已填写了在 Dell EMC PowerSwitch 系列 S4148-ON 架顶式交换机上配置的资源。如果您要使用备用网络资源来配置环 境,请填写本指南中提供的空白工作表,网址为初始配置工作表。 此外,请务必在以下填写好的初始配置工作表中记下您为群集定义的管理员密码。未为您提供用户定义的密码的示例。 表.
表. 16: 初始配置工作表(已填写) (续) 100 255.255.255.0/2 4 192.168.1.1 192.168.1.11-15 存储网络 使客户端能够访问群集中的存储。存储网络中的 IP 地址用于 iSCSI 目标、iSCSI 启动器和全局存储发现 IP 地址。 每个 PowerStore X 型号设备至少需要 6 个 IP 地址。但是,为了提高性能,极力建议为每个 PowerStore X 型号 设备设置至少 8 个 IP 地址。 如果您选择创建全局存储发现 IP 地址,则每个设备至少需要 7 个 IP 地址,推荐 9 个 IP 地址。 VLAN 网络掩码/前缀长度 网关 IP 地址 255.255.255.0/2 4 192.168.2.1 192.168.2.
表. 16: 初始配置工作表(已填写) (续) vCenter Server IP 地址/主机名称 100.0.100.220 vCenter 管理员用户名 administrator@vsphere.
A 扩展存储网络以跨多个端口运行 附录包含以下信息。 主题: • 扩展存储网络 扩展存储网络 您可以扩展存储网络以跨 PowerStore X 型号 设备上的多个端口运行。 您将需要以下信息来执行扩展存储网络的步骤。 注: 下面的示例网络资源可用于扩展在本指南的以前章节中在两个 Dell EMC PowerSwitch 系列 S4148 架顶式交换机上配置的存储 网络。有关详细信息,请参阅使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机进行配置。如果您未配置本指南中所述的相同 存储网络,请将示例资源替换为与您的环境匹配的值。 表.
执行以下步骤以配置其他端口并扩展您已在 PowerStore X 型号 设备上配置的存储网络。 1. 用线缆将节点连接到交换机以进行存储网络扩展。 2. 在架顶式 (ToR) 交换机上配置 VLAN。 3. 添加 IP 地址并将存储网络映射到虚拟端口。 用线缆将节点连接到 ToR 交换机 以下步骤提供了用线缆将 4 端口卡的端口 2 连接到两个 Dell PowerSwitch 系列 S4148 架顶式 (ToR) 交换机的示例。 要使用这些说明,必须已按照使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机进行配置中所述配置存储网络和 ToR 交换机。 以下示例使用 4 端口卡的端口 2。但是,您可以选择使用端口 3 或 I/O 模块中的任意端口(如果您的节点配置了它)。 如图所示,在用线缆将节点连接到 ToR 交换机时,必须用线缆将底部节点 (A) 和顶部节点 (B) 连接到相反的交换机。 1 2 图 10: 用线缆连接其他端口 1. 将底部节点 (A) 的端口 2 连接到底部交换机 (1) 的端口 2。 2.
2. 进入全局配置模式。 configure terminal 3. 将存储网络 VLAN 配置为通过 ToR 交换机 1 端口 2 运行。 interface ethernet 1/1/2 switchport mode trunk switchport trunk allowed vlan 200 no shutdown exit 4. 对 ToR 交换机 2 上的端口 53 重复步骤 1-3。 表.
B 创建其他存储网络 本附录包含以下信息。 主题: 新建存储网络 • 新建存储网络 您最多可以配置 32 个存储网络,并且 4 端口卡上的每个端口最多 8 个网络。 您通过 4 端口卡上的每一个端口最多可以配置 8 个存储网络。 您将需要以下信息来执行创建新存储网络的步骤。 注: 可以在使用 Dell EMC PowerSwitch 系列 S4148-ON 交换机进行配置中所述的为原始存储网络配置的两个 Dell EMC PowerSwitch 系列 S4148 架顶式 (ToR) 交换机上使用以下示例网络资源。如果您未使用本指南中所述的相同 Dell EMC PowerSwitch 系列 S4148 ToR 交换机,请将示例资源替换为与您的环境匹配的值。 表.
表. 21: PowerStore X 型号 设备以太网端口到虚拟端口映射 4 端口卡上的以太网端口 虚拟端口 vSphere 端口组 上行链路 端口 0 vFEPort2 PG_Storage_TGT2 上行链路 2 端口 1 vFEPort1 PG_Storage_TGT1 上行链路 1 端口 2 vFEPort6 PG_Storage_TGT4 上行链路 4 端口 3 vFEPort3 PG_Storage_TGT3 上行链路 3 在 PowerStore X 型号 设备上执行以下步骤来配置要在其上创建新存储网络的其他端口。 1. 用线缆将节点连接到 ToR 交换机。 2. 在 ToR 交换机上配置存储网络。 3.
在 ToR 交换机上配置存储网络 以下步骤提供了在两个 Dell PowerSwitch 系列 S4148 架顶式 (ToR) 交换机上配置存储网络的示例。 您可以在执行这些步骤之前或之后,用线缆将 PowerStore T 型号 设备节点连接到交换机。有关步骤,请参阅用线缆将节点连接到 ToR 交换机。 请参阅新存储网络资源,了解以下各项的列表: ● 添加新存储网络所需的网络资源 ● 以下步骤中使用的示例值 1. 与第一个 ToR 交换机 (Switch1) 建立终端连接。 2. 进入全局配置模式。 configure terminal 3. 在 ToR 交换机 1 上配置存储网络。 interface vlan 210 description Storage_Network2 exit 4. 在 ToR 交换机 1 上将存储网络配置为通过端口 2 运行。 interface ethernet 1/1/2 switchport mode trunk switchport trunk allowed vlan 210 no shutdown 5.
c. 在虚拟选项卡上,在名称列中找到您在其上扩展了存储网络的端口。 链路状态应为绿色,并且存储网络应显示在已为存储映射列中。 d.
C 其他 Dell EMC PowerSwitch 系列 S4148-ON 交 换机配置操作 本附录包括以下信息: 主题: 将交换机重置为出厂设置 Dell EMC PowerSwitch 系列 S4148-ON ToR 交换机的运行配置 • • 将交换机重置为出厂设置 如有必要,您可以将 Dell EMC PowerSwitch 系列 S4148-ON 交换机重置为默认出厂设置。 注: 如果您重置了交换机,所有现有配置均会丢失,如果正在使用该交换机,则会导致流量中断。 当 Dell EMC PowerSwitch 系列 S4148-ON 交换机重置为出厂默认设置时: Telnet 处于禁用状态 SSH 处于启用状态 DHCP 处于启用状态 默认交换机用户名和密码均为 admin。 ● ● ● ● 注: 戴尔建议在首次登录期间更改管理员密码。 OS10# delete startup-configuration Proceed to delete startup-configuration [confirm yes/no(default)]:y OS10# reload System configu
表. 23: ToR 交换机上的运行配置示例 交换机 1 交换机 2 interface breakout 1/1/30 map 100g-1x username admin password $6$q9QBeYjZ$jfxzVqGhkxX3smxJSH9DDz7/3OJc6m5w jF8nnLD7/VKx8SloIhp4NoGZs0I/ UNwh8WVuxwfd9q4pWIgNs5BKH. role sysadmin ntp server 100.0.10.
表.
表.
表.
表.
表.