Setup Guide

ManualsBrandsDell ManualsCompellent (SCPowerStore Rack

Table Of Contents

Regulatory Model: 300-000-239

40U-P Cabinet

Unpacking and Setup Guide

Rev. Rev 02

July 2020

This Unpacking and Setup Guide contains information about the 40U-P cabinet. Topics include:

• Before you start .........................................................................................................................................................................................................2

• Tools required..............................................................................................................................................................................................................2

• Hardware acclimation.................................................................................................................................................................................................2

• Steps to unpack and setup cabinet..........................................................................................................................................................................3

• Remove the ramp and shipping material from the cabinet................................................................................................................................... 3

• Remove the cabinet shipping brackets....................................................................................................................................................................5

• Attach the unloading ramp........................................................................................................................................................................................ 6

• Roll the cabinet down the ramp................................................................................................................................................................................7

• Position and level the cabinet................................................................................................................................................................................... 8

• Power requirements...................................................................................................................................................................................................8

• Attach (optional) brackets........................................................................................................................................................................................11

• Install the lower trim strip.........................................................................................................................................................................................12

• Ground the cabinet................................................................................................................................................................................................... 13

• Repackaging shipping material (2-piece ramp kits only)......................................................................................................................................14

• If you need help......................................................................................................................................................................................................... 15

Summary of content (16 pages)

PAGE 1
40U-P Cabinet Unpacking and Setup Guide Rev. Rev 02 July 2020 This Unpacking and Setup Guide contains information about the 40U-P cabinet. Topics include: • • • • • • • • • • • • • • • Before you start .........................................................................................................................................................................................................2 Tools required...........................................................................................
PAGE 2
Before you start This section contains important information you should read prior to unpacking and setting up the 40U-P cabinet. CAUTION: Some products are designed for installation by trained service personnel only. Attempts by unqualified personnel to set up and start certain products may result in system damage and may void product warranties. Contact your representative for detailed warranty, installation, and initialization policies.
PAGE 3
If the last 24 hours of the TRANSIT/STORAGE environment was: …and the OPERATING environment is: …then let the system or component acclimate in the new environment this many hours: Damp >30% RH Hot >72°F (22°C) Dry <30% RH Humid 30–45% RH Hot >72°F (22°C) Humid 45–60% RH <86°F (30°C) 8 hours Hot >72°F (22°C) Humid >60% RH <86°F (30°C) 16 hours Unknown IMPORTANT: • • If there are signs of condensation after the recommended acclimation time has passed, allow an additional eight (8) hours to stabi
PAGE 4
CL4691 2. Do not pull a ramp down from the top. To release the ramp from the pallet, grasp the ramp, pull it straight back toward you, then pull it straight up to free it from the screws.
PAGE 5
Rear Accessory Kit Bracket Bracket Screws Rotated 90 EMC3552 3. Remove the plastic covering from the cabinet. Remove the cabinet shipping brackets Steps 1. At the rear of the cabinet, remove the rear shipping bracket, by removing the bolts that go through the bracket to the cabinet and into the pallet. 2. At the front of the cabinet, remove the bottom cabinet bezel, if necessary. Pull the bezel straight out to remove it. 3. Remove the bolts that attach the cabinet to the front shipping bracket.
PAGE 6
Attach the unloading ramp Steps 1. Insert the ramp brackets into the pallet notches in the rear of the pallet. 2. If your shipment includes a two-piece ramp, attach part A to the pallet and part B to part A.
PAGE 7
CL4692 Roll the cabinet down the ramp About this task NOTE: Make certain the leveling feet are secured in the UP position before moving the cabinet. Secured feet allow the cabinet to roll off the ramp and into position. If you need to adjust the leveling feet, use the 6mm hex key (top access) or an adjustable wrench (bottom access) to turn the feet counter-clockwise. This raises them to the UP position. Rear Leveling Feet Rails EMC2845 WARNING: The cabinet is heavy.
PAGE 8
ATTENZIONE! Poiché il cabinet è molto pesante assicurarsi di essere in un numero sufficiente di persone e di avere un appoggio sicuro prima di spingerlo sullo scivolo. ADVERTENCIA! El bastidor es pesado. Asegúrese de contar con ayuda suficiente y de tener un apoyo seguro antes de colocar el bastidor en la rampa. WARNING: Balance the cabinet from the sides; do not grasp the plastic bezels or other components on the front of the cabinet.
PAGE 9
Table 1. Single-phase power connection requirements (continued) Specification North American 3 wire connection (2 L and 1 International and Australian G)a 3 wire connection (1 L, 1 N, and 1 G) Frequency 50 - 60 Hz 50 - 60 Hz Circuit breakers 30 A 32 A Power zones Two Two Power requirements at site (minimum to maximum) • • a. One to six 30 A, single-phase drops per zone Each rack requires a minimum of two drops to a maximum of 12 drops.
PAGE 10
Table 3. Three-phase AC power connection requirements (continued) Specification North American (Delta) 4 wire connection (3 L and 1 • • International and Australian (Wye) G)a 5 wire connection (3 L, 1 N, and 1 G) One 32 A, three-phase drop per zone Each rack requires a minimum of two drops to a maximum of four drops. This will be determined by the system configuration and the power needs for that configuration.
PAGE 11
Attach (optional) brackets We strongly recommend that you secure your cabinet to the floor with stabilizing brackets. Make sure the cabinet is in its final location before attaching the brackets, then use the supplied bolts and mounting holes to attach them to the cabinet and floor About this task (3) (3) CL4830 Figure 1. Anti-tip bracket (installed on the front of cabinet) (3) (3) CL4832 Figure 2.
PAGE 12
(3) (3) (3) (3) CL4833 Figure 3. Seismic bracket (installed on the front, back, and sides of the cabinet) Install the lower trim strip This procedure describes how to install the lower trim strip. About this task NOTE: If the cabinet is shipped with a front door, there is no need to install the lower front bezel/trim strip. Steps 1. Wipe down the lower cabinet with alcohol wipes. 2. On the underside of the lower trim strip, remove the double-sided tape from the velcro fasteners. Figure 4.
PAGE 13
Figure 5. Attaching lower trim strip Ground the cabinet Equipment correctly installed within the cabinet is grounded through the AC power cables and connectors. In general, supplemental grounding is not required.
PAGE 14
Repackaging shipping material (2-piece ramp kits only) About this task Follow these steps to repackage the shipping material: Steps 1. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections, as shown: 2 1 3 CL4690 2. Stack the shipping brackets on the pallet, as shown: 1 2 3 CL4697 3. Place ramp section B upside-down on the pallet, then stack section A, right-side up. 4. Stack the two folded outer sleeves above the ramp sections. 5.
PAGE 15
6. Band the unit with shipping straps as shown: CL4751 7. Use the following information to determine how to return the repackaged shipping material: • • If the carrier unpacked the cabinet, the carrier handles the return shipment to the packaging supplier. If the cabinet was unpacked after delivery, refer to the contact number attached to the pamphlet for repacking. This contact is the carrier network for the initial shipment and they will follow the same process as for the initial shipments.
PAGE 16
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.