Service Manual

The Dell Monitoring MIB provides access to the following statistics.
• IP Statistics: Bcast: Received: Object = f10BcastPktRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.1
• IP Statistics: Bcast: Sent: Object = f10BcastPktSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.2
• IP Statistics: Mcast: Received: Object = f10McastPktRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.3
• IP Statistics: Mcast: Sent: Object = f10McastPktSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.1.4
• ARP Statistics: Rcvd: Request: Object = f10ArpReqRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.1
• ARP Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3
• ARP Statistics: Sent: Request: Object = f10ArpReqSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.2
• ARP Statistics: Sent: Replies: Object = f10ArpReplySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.4
• ARP Statistics: Sent: Proxy: Object = f10ArpProxySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.5
Example
Dell#show ip traffic
Control Processor IP Traffic:
IP statistics:
Rcvd: 23857 total, 23829 local destination
0 format errors, 0 checksum errors, 0 bad hop count
0 unknown protocol, 0 not a gateway
0 security failures, 0 bad options
Frags: 0 reassembled, 0 timeouts, 0 too big
0 fragmented, 0 couldn't fragment
Bcast: 28 received, 0 sent; Mcast: 0 received, 0 sent
Sent: 16048 generated, 0 forwarded
21 encapsulation failed, 0 no route
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0 unreachable
0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 info request, 0 other
Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp
0 info reply, 0 time exceeded, 0 parameter problem
UDP statistics:
Rcvd: 0 total, 0 checksum errors, 0 no port
0 short packets, 0 bad length, 0 no port broadcasts, 0 socket full
Sent: 0 total, 0 forwarded broadcasts
TCP statistics:
Rcvd: 23829 total, 0 checksum errors, 0 no port
Sent: 16048 total
ARP statistics:
Rcvd: 156 requests, 11 replies
Sent: 21 requests, 10 replies (0 proxy)
Routing Processor1 IP Traffic:
show tcp statistics
View information on TCP trac through the switch.
Syntax
show tcp statistics {all | cp | rp1 | rp2}
Parameters
all Enter the keyword all to view all TCP information.
cp Enter the keyword cp to view only TCP information from the Control Processor.
rp1 Enter the keyword rp1 to view only TCP statistics from Route Processor 1.
IPv4 Routing
747