Administrator Guide

MIB Object OID Access or Permission Description
dellNetPortSecIfSecureMacAge
Enable
1.3.6.1.4.1.6027.3.31.1.2.1.1.11 read-write Enables aging of the dynamically
secured MAC addresses learnt on the
interface.
Enabling and viewing SNMP for port security
To enable or view DELL-NETWORKING-PORT-SECURITY-MIB, configure snmp-server in read-write mode using the snmp-server
community public rw command. You can enable the port security feature on the Dell EMC Networking OS using the snmpset
command. Also, you can view if the port security feature is enabled or disabled using the snmpwalk command.
To configure dellNetPortSecIfSecureMacLimit as 100 on an interface whose ifIndex is 2101252, use the following command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 100
To remove dellNetPortSecIfSecureMacLimit configuration on an interface whose ifIndex is 2101252, use the following
command.
snmpset –v 2c –c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252 i 2147483647
To retrieve dellNetPortSecIfSecureMacLimit configured on an interface whose ifIndex is 2101252, use the following
command.
snmpwalk -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.1.1.3. 2101252
SNMPv2-SMI::enterprises.6027.3.31.1.2.1.1.3. 2101252 = INTEGER: 10
MIB objects for configuring MAC addresses
This section describes about the MIB objects dellNetPortSecSecureStaticMacAddrTable to configure and un-configure static
MAC addresses in the system. The OID of this MIB table is 1.3.6.1.4.1.6027.3.31.1.2.2.
The table is indexed by the following parameters:
• MAC Address (Octet string of length 6 and MAC address ( in decimal) as value
• VLAN ID
• Interface Index
NOTE:
MAC addresses cannot be retrieved using dellNetPortSecSecureStaticMacAddrTable and
dellNetPortSecSecureMacAddrTable. These tables are valid only if port security feature is enabled globally in the
system.
Table 109. MIB Objects for configuring MAC addresses
MIB Object OID Access or Permission Description
dellNetPortSecIfSecureStaticMa
cRowStatus
1.3.6.1.4.1.6027.3.31.1.2.2.1.4 read-write Allows adding or deleting entries to or
from the table
dellNetPortSecSecureStaticMac
AddrTable.
Enabling and viewing SNMP for static MAC addresses
You can enable and view SNMP for static MAC addresses using snmpset and snmpget command. Following example shows how to
enable and view the static MAC addresses.
To configure a static MAC address (00:00:00:00:11:11) on a vlan (100) on interface whose ifIndex is (2101252), use the following
command.
snmpset -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.2.1.4.6.0.0.0.0.17.17.100.2101252
i 4
To remove the configure the above configured static MAC address, use the following command.
snmpset -v 2c -c public 10.16.129.26 1.3.6.1.4.1.6027.3.31.1.2.2.1.4.6.0.0.0.0.17.17.100.2101252
i 6
Simple Network Management Protocol (SNMP)
759