Administrator Guide

DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip ?
A.B.C.D Source address
any Any source host
host A single source host
DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip 222.1.1.1 ?
Mask A.B.C.D or /nn Mask in dotted decimal or in slash format
DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip 222.1.1.1 /32 ?
A.B.C.D Destination address
any Any destination host
host A single destination host
DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip 222.1.1.1 /32 77.1.1.1 ?
Mask A.B.C.D or /nn Mask in dotted decimal or in slash format
DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip 222.1.1.1 /32 77.1.1.1 /32 ?
DellEMC(conf-redirect-list)#redirect 3.3.3.3 ip 222.1.1.1 /32 77.1.1.1 /32
DellEMC(conf-redirect-list)#do show ip redirect-list
IP redirect-list xyz:
Defined as:
seq 5 redirect 3.3.3.3 ip host 222.1.1.1 host 77.1.1.1
Applied interfaces:
None
You can apply multiple rules to a single redirect-list. The rules are applied in ascending order, starting with the rule that has the lowest
sequence number in a redirect-list displays the correct method for applying multiple rules to one list.
Example: Creating Multiple Rules for a Redirect-List
DellEMC(conf)#ip redirect-list test
DellEMC(conf-redirect-list)#seq 10 redirect 10.1.1.2 ip 20.1.1.0/24 any
DellEMC(conf-redirect-list)#seq 15 redirect 10.1.1.3 ip 20.1.1.0/25 any
DellEMC(conf-redirect-list)#seq 20 redirect 10.1.1.3 ip 20.1.1.128/24 any
DellEMC(conf-redirect-list)#show config
!
ip redirect-list test
seq 10 redirect 10.1.1.2 ip 20.1.1.0/24 any
seq 15 redirect 10.1.1.3 ip 20.1.1.0/25 any
seq 20 redirect 10.1.1.3 ip 20.1.1.0/24 any
DellEMC(conf-redirect-list)#
NOTE:
Starting with the Dell EMC Networking OS version 9.4(0.0), the use of multiple recursive routes with the same
source-address and destination-address combination in a redirect policy on an router.
A recursive route is a route for which the immediate next-hop address is learned dynamically through a routing protocol and acquired
through a route lookup in the routing table. You can configure multiple recursive routes in a redirect list by entering multiple seq
redirect commands with the same source and destination address and specify a different next-hop IP address. In this way, the
recursive routes are used as different forwarding routes for dynamic failover. If the primary path goes down and the recursive route is
removed from the routing table, the seq redirect command is ignored and the next command in the list with a different route is used.
Apply a Redirect-list to an Interface using a Redirect-
group
IP redirect lists are supported on physical interfaces as well as virtual local area network (VLAN) and port-channel interfaces.
NOTE:
When you apply a redirect-list on a port-channel, when traffic is redirected to the next hop and the destination
port-channel is shut down, the traffic is dropped. However, the traffic redirected to the destination port-channel is
sometimes switched.
To apply a redirect list to an interface, use the following command. You can apply multiple redirect-lists can be applied to a redirect-group.
It is also possible to create two or more redirect-groups on one interface for backup purposes.
Apply a redirect list (policy-based routing) to an interface.
INTERFACE mode
ip redirect-group redirect-list-name test l2–switch
• redirect-list-name is the name of a redirect list to apply to this interface.
• FORMAT: up to 16 characters
• You can use the l2–switch option to apply the re-direct list to Layer2 traffic.
546
Policy-based Routing (PBR)