Users Guide

Description Behavior at Peer Up Behavior During Run Time Action to Take
information, refer to the Release
Notes for this release.
VLT LAG ID is not congured on
one VLT peer
A syslog error message is
generated. The peer with the
VLT congured remains active.
A syslog error message is
generated. The peer with the
VLT congured remains active.
Verify the VLT LAG ID is
congured correctly on both VLT
peers.
VLT LAG ID mismatch
The VLT port channel is brought
down.
A syslog error message is
generated.
The VLT port channel is brought
down.
A syslog error message is
generated.
Perform a mismatch check after
the VLT peer is established.
Reconguring Stacked Switches as VLT
To convert switches that have been stacked to VLT peers, use the following procedure.
1 Remove the current conguration from the switches. You will need to split the conguration up for each switch.
2 Copy the les to the ash memory of the appropriate switch.
3 Copy the les on the ash drive to the startup-cong.
4 Reset the stacking ports to user ports for both switches.
5 Reload the stack and conrm the new congurations have been applied.
6 On the Secondary switch (stack-unit 2), enter the command stack-unit 2 renumber 1.
7 Conrm the reload query.
8 After reloading, conrm that VLT is enabled.
9 Conrm that the management ports are interconnected or connected to a switch that can transfer Heartbeat information.
Specifying VLT Nodes in a PVLAN
You can congure VLT peer nodes in a private VLAN (PVLAN). VLT enables redundancy without the implementation of Spanning Tree
Protocol (STP), and provides a loop-free network with optimal bandwidth utilization.
Because the VLT LAG interfaces are terminated on two dierent nodes, PVLAN conguration of VLT VLANs and VLT LAGs are
symmetrical and identical on both the VLT peers. PVLANs provide Layer 2 isolation between ports within the same VLAN. A PVLAN
partitions a traditional VLAN into sub-domains identied by a primary and secondary VLAN pair. With VLT being a Layer 2 redundancy
mechanism, support for conguration of VLT nodes in a PVLAN enables Layer 2 security functionalities. To achieve maximum VLT resiliency,
you should congure the PVLAN IDs and mappings to be identical on both the VLT peer nodes.
The association of PVLAN with the VLT LAG must also be identical. After the VLT LAG is congured to be a member of either the primary
or secondary PVLAN (which is associated with the primary), ICL becomes an automatic member of that PVLAN on both switches. This
association helps the PVLAN data ow received on one VLT peer for a VLT LAG to be transmitted on that VLT LAG from the peer.
You can associate either a VLT VLAN or a VLT LAG to a PVLAN. First congure the VLT interconnect (VLTi) or a VLT LAG by using the
peer-link port-channel id-number command or the VLT VLAN by using the peer-link port-channel id-number
peer-down-vlan vlan interface number command and the switchport command. After you specify the VLTi link and VLT
LAGs, you can associate the same port channel or LAG bundle that is a part of a VLT to a PVLAN by using the
interface interface
and switchport mode private-vlan commands.
When a VLTi port in trunk mode is a member of symmetric VLT PVLANs, the PVLAN packets are forwarded only if the PVLAN settings of
both the VLT nodes are identical. You can congure the VLTi in trunk mode to be a member of non-VLT PVLANs if the VLTi is congured
on both the peers. MAC address synchronization is performed for VLT PVLANs across peers in a VLT domain.
Virtual Link Trunking (VLT)
1093