Administrator Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S4048T-ON

Dell EMC Command Line Reference Guide for

the S4048T–ON System

9.14.2.6

Summary of content (1707 pages)

PAGE 1
Dell EMC Command Line Reference Guide for the S4048T–ON System 9.14.2.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents 1 About this Guide......................................................................................................................... 42 Objectives.............................................................................................................................................................................42 Audience......................................................................................................................................................................
PAGE 4
asf-mode.............................................................................................................................................................................. 85 banner exec..........................................................................................................................................................................86 banner login..................................................................................................................................
PAGE 5
show environment............................................................................................................................................................. 132 show inventory................................................................................................................................................................... 133 show login statistics...................................................................................................................................
PAGE 6
ip access-group............................................................................................................................................................ 187 ip mirror-access-group................................................................................................................................................ 189 ip control-plane egress-filter.......................................................................................................................................
PAGE 7
match ip address......................................................................................................................................................... 244 match ip next-hop....................................................................................................................................................... 245 match ip route-source................................................................................................................................................
PAGE 8
permit ether-type (for Extended MAC ACLs)...............................................................................................................287 permit icmp (for Extended IP ACLs).............................................................................................................................. 288 permit udp (for Extended IP ACLs)................................................................................................................................
PAGE 9
address-family..............................................................................................................................................................339 aggregate-address...................................................................................................................................................... 340 bgp add-path........................................................................................................................................................
PAGE 10
neighbor distribute-list................................................................................................................................................ 382 neighbor ebgp-multihop..............................................................................................................................................383 neighbor fall-over........................................................................................................................................................
PAGE 11
show ip bgp regexp..................................................................................................................................................... 438 show ip bgp summary................................................................................................................................................. 439 show running-config bgp............................................................................................................................................
PAGE 12
dcb-enable....................................................................................................................................................................475 PFC Commands.................................................................................................................................................................476 clear pfc counters...........................................................................................................................................
PAGE 13
Debugging and Diagnostics.......................................................................................................518 Diagnostics and Monitoring Commands......................................................................................................................... 518 logging coredump stack-unit...................................................................................................................................... 518 Offline Diagnostic Commands.......................
PAGE 14
arp inspection-trust.................................................................................................................................................... 559 clear ip dhcp snooping................................................................................................................................................ 560 clear ipv6 dhcp snooping binding...............................................................................................................................
PAGE 15
17 FIP Snooping.......................................................................................................................... 598 clear fip-snooping database interface vlan.................................................................................................................... 598 clear fip-snooping statistics............................................................................................................................................. 598 debug fip snooping..............
PAGE 16
show redundancy.............................................................................................................................................................. 635 21 ICMP Message Types.............................................................................................................. 638 22 Internet Group Management Protocol (IGMP)...........................................................................640 IGMP Commands..............................................................
PAGE 17
interface range macro name......................................................................................................................................683 interface vlan............................................................................................................................................................... 684 intf-type cr4 autoneg..................................................................................................................................................
PAGE 18
tdr-cable-test...............................................................................................................................................................739 show tdr........................................................................................................................................................................740 UDP Broadcast Commands.....................................................................................................................................
PAGE 19
ip proxy-arp........................................................................................................................................................................ 780 ip route.................................................................................................................................................................................781 ip source-route...........................................................................................................................
PAGE 20
ipv6 nd prefix..................................................................................................................................................................... 833 ipv6 nd reachable-time..................................................................................................................................................... 833 ipv6 route..............................................................................................................................................
PAGE 21
graceful-restart t1..............................................................................................................................................................874 graceful-restart t2.............................................................................................................................................................875 graceful-restart t3....................................................................................................................................
PAGE 22
lacp system-priority........................................................................................................................................................... 919 port-channel-protocol lacp.............................................................................................................................................. 920 show lacp......................................................................................................................................................
PAGE 23
advertise management-tlv (Interface)..................................................................................................................... 960 clear lldp counters........................................................................................................................................................ 961 clear lldp neighbors......................................................................................................................................................
PAGE 24
show ip msdp.....................................................................................................................................................................999 show ip msdp sa-cache rejected-sa............................................................................................................................. 1000 35 Multicast Listener Discovery Protocol..................................................................................... 1002 clear ipv6 mld groups...............
PAGE 25
mtrace......................................................................................................................................................................... 1032 show ip multicast-cam.............................................................................................................................................. 1033 show ip mroute....................................................................................................................................................
PAGE 26
IPv6 Object Tracking Commands..................................................................................................................................1069 show track ipv6 route............................................................................................................................................... 1069 track interface ipv6 routing.......................................................................................................................................
PAGE 27
show ip ospf................................................................................................................................................................. 1115 show ip ospf asbr........................................................................................................................................................ 1116 show ip ospf database.........................................................................................................................................
PAGE 28
ip pim join-filter............................................................................................................................................................1164 ip pim ingress-interface-map.................................................................................................................................... 1165 ip pim neighbor-filter.................................................................................................................................................
PAGE 29
show running-config monitor session........................................................................................................................... 1205 source (port monitoring)................................................................................................................................................ 1206 44 Private VLAN (PVLAN).......................................................................................................... 1209 ip local-proxy-arp.....................
PAGE 30
qos-policy-input..........................................................................................................................................................1249 qos-policy-output...................................................................................................................................................... 1250 queue egress........................................................................................................................................................
PAGE 31
output-delay..................................................................................................................................................................... 1295 passive-interface............................................................................................................................................................. 1296 redistribute.........................................................................................................................................
PAGE 32
Authorization and Privilege Commands........................................................................................................................ 1340 authorization...............................................................................................................................................................1340 aaa authorization commands....................................................................................................................................
PAGE 33
TACACS+ Commands.....................................................................................................................................................1379 tacacs-server group...................................................................................................................................................1379 debug tacacs+............................................................................................................................................................
PAGE 34
clear ip dhcp snooping............................................................................................................................................... 1419 ip dhcp relay................................................................................................................................................................1420 ip dhcp snooping...................................................................................................................................................
PAGE 35
SNMP Commands...........................................................................................................................................................1455 show snmp..................................................................................................................................................................1455 show snmp engineID.................................................................................................................................................
PAGE 36
56 Stacking............................................................................................................................... 1518 redundancy disable-auto-reboot.................................................................................................................................... 1518 redundancy force-failover stack-unit............................................................................................................................ 1519 redundancy protocol...............
PAGE 37
enable.......................................................................................................................................................................... 1557 server...........................................................................................................................................................................1557 SupportAssist Activity Commands.....................................................................................................................
PAGE 38
tunnel destination............................................................................................................................................................ 1590 tunnel dscp........................................................................................................................................................................1591 tunnel flow-label...................................................................................................................................
PAGE 39
65 VLT Proxy Gateway............................................................................................................... 1628 proxy-gateway lldp.......................................................................................................................................................... 1628 proxy-gateway static......................................................................................................................................................
PAGE 40
vnid.................................................................................................................................................................................... 1663 vni-profile..........................................................................................................................................................................1663 vxlan-instance..........................................................................................................................
PAGE 41
crypto x509 revocation...................................................................................................................................................1702 debug crypto.................................................................................................................................................................... 1703 logging secure..............................................................................................................................................
PAGE 42
1 About this Guide This guide provides information about the Dell EMC Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell EMC Networking OS.
PAGE 43
CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. NOTE: The Warning icon signals information about hardware handling that could result in injury.
PAGE 44
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell EMC Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 45
User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a Command mode, there are several ways to access help: To obtain a list of keywords at any command mode: Type a ? at the prompt or after a keyword. There must always be a space before the ?.
PAGE 46
• • • • • • Commands are not case-sensitive. Enter partial (truncated) command keywords. For example, you can enter int teng 1/1/1 for the interface tengigabitethernet 1/1/1 command. Use the TAB key to complete keywords in commands. Use the up Arrow key to display the last enabled command. Use either the Backspace key or Delete key to erase the previous character. Use the left and right Arrow keys to navigate left or right in the Dell EMC Networking OS command line.
PAGE 47
Filtering show Commands You can filter commands using the show command to find specific information, display certain information only, or begin the command output at the first instance of a regular expression or phrase. Execute a show command and a pipe ( | ), and one of the following parameters and a regular expression to show output that either excludes or includes the specified parameters.
PAGE 48
To enable the VRF feature and cause all VRF-related commands to be available or viewable in the CLI interface, use the following command. You must enable the VRF feature before you can configure its related attributes. DellEMC(conf)# feature vrf Based on if the VRF feature is identified as supported in the Feature Configuration file, configuration command feature vrf becomes available for usage. This command is stored in the running-configuration and precedes all other VRF-related configurations.
PAGE 49
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.4(0.0) Introduced on the S4810, S4820T, and S6000. Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms.
PAGE 50
CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, see Control Plane Policing (CoPP). To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command. The prompt changes to include conf-control-cpuqos. You can return to CONFIGURATION mode by using the exit command. DHCP Mode To enable and configure Dynamic Host Configuration Protocol (DHCP), use DHCP mode.
PAGE 51
NOTE: Each mode prompt is preceded by the host name. EXEC Privilege Mode The enable command accesses EXEC Privilege mode. If an administrator has configured an “Enable” password, you are prompted to enter it. EXEC Privilege mode allows you to access all the commands accessible in EXEC mode, plus other commands, such as to clear address resolution protocol (ARP) entries and IP addresses. In addition, you can access CONFIGURATION mode to configure interfaces, routes and protocols on the switch.
PAGE 52
Prompt Interface Type DellEMC(confif-po-0)# Port-channel interface number The range is from 1 to 128. DellEMC(confif-vl-0)# VLAN Interface then VLAN number (range 1–4094) DellEMC(confif-ma-1/1)# Management Ethernet interface then slot/port information DellEMC(confif-tu-0)# Tunnel interface then tunnel ID. DellEMC(confif-range)# Designated interface range (used for bulk configuration).
PAGE 53
1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the line command. Include the keywords console or vty and their line number available on the switch. The prompt changes to include config-line-console or config-line-vty. You can exit this mode by using the exit command. MAC ACCESS LIST Mode To enter MAC ACCESS LIST mode and configure either standard or extended access control lists (ACLs), use the mac access-list standard or mac access-list extended command. To enter MAC ACCESS LIST mode: 1.
PAGE 54
PORT-CHANNEL FAILOVER-GROUP Mode To configure shared LAG state tracking, use PORT-CHANNEL FAILOVER-GROUP mode. For more information, see Port Channel Commands. To enter PORT-CHANNEL FAILOVER-GROUP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the port-channel failover-group command. The prompt changes to include conf-po-failover-grp. You can return to CONFIGURATION mode by using the exit command. PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode.
PAGE 55
2. Use the router bgp command, and then enter the AS number. The prompt changes to include conf-router_bgp. You can return to CONFIGURATION mode by using the exit command. ROUTER ISIS Mode To enable and configure Intermediate System to Intermediate System (ISIS), use ROUTER ISIS mode. For more information, see Intermediate System to Intermediate System (IS-IS). To enter ROUTER ISIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the router isis command.
PAGE 56
SupportAssist Mode To enable and configure the SupportAssist, use SupportAssist mode. For more information, see SupportAssist. 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the support-assist command. The prompt changes to include conf-supportassist. You can return to CONFIGURATION mode by using the exit command. TRACE-LIST Mode To configure a Trace list, use TRACE-LIST mode. To enter TRACE-LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 57
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 58
system: Enter the keyword system: to use the system image file URL (system). ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath. nfsmount Enter the keyword nfsmount: to retrieve the image from a mounted NFS file system. nfsmount://filepath system: Enter the keyword system: to retrieve the image from the system. usbflash Enter the keyword usbflash: to retrieve the image from the USB flash memory. usbflash://filename.
PAGE 59
directory name and path Enter the directory name and path as follows: directory name ([[flash://]directory_path]) NOTE: The cd command without any arguments will change the current directory to flash: Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 60
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. copy http://admin:admin123@10.16.206.77/sample_file flash://sample_file copy Copy one file to another location. Dell EMC Networking OS supports IPv4 and IPv6 addressing for FTP, HTTP, TFTP, and SCP (in the hostip field).
PAGE 61
Version Description 9.3(0.1) Added the http parameter on the S6000, Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. 8.4.1.0 Added IPv6 addressing support for FTP, TFTP, and SCP. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added usbflash and rpm0usbflash commands on E-Series. 7.6.1.0 Introduced on the S-Series and added the SSH port number to the SCP prompt sequence on all systems. 7.5.1.
PAGE 62
Password to login remote host: DellEMC# Example DellEMC# copy scp: flash: Address or name of remote host []: 10.11.199.134 Port number of the server [22]: 99 Source file name []: test.cfg User name to login remote host: admin Password to login remote host: Destination file name [test.cfg]: test1.cfg DellEMC# Example DellEMC# copy compressed-config compressed-cfg ! 6655 bytes successfully copied DellEMC# DellEMC#copy compressed-config ftp: Address or name of remote host []: 10.11.8.
PAGE 63
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 64
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 65
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series Usage Information You must include the colon (:) when entering this command. After reformatting is complete, three empty directories are automatically created on flash: CRASH_LOG_DIR, TRACE_LOG_DIR and NVTRACE_LOG_DIR.
PAGE 66
CAUTION: If you elect to format the flash, all files – including the startup configuration file – are lost. If you do decide to format the specified flash, consider saving the running configuration as the startup configuration after formatting the flash (use the write memory command or copy running-config startup-config command). Related Commands • • copy — copy one file to another location. show file-systems — display information about the file systems on the system.
PAGE 67
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. Example Related Commands DellEMC# mount nfs nfstest nfs-mount-point usrname pwd DellEMC# • cd — change the working directory.
PAGE 68
Parameters copy http: flash: Address or name of remote host []: 10.16.206.77 Port number of the server [80]: Source file name []: sample_file User name to login remote host: x Password to login remote host: Destination file name [sample_file]: Defaults None. Command Modes EXEC Privilege Command History Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.
PAGE 69
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.1.0 Introduced on C-Series E-Series Original command restore factory-defaults Restore factory defaults. Syntax Parameters restore factory-defaults stack-unit {stack—unit—number | all} {clear-all | bootvar | nvram} factory-defaults Return the system to its factory default mode. stack-unit-number Enter the stack member unit identifier to restore only the mentioned stack-unit. The range is from 1 to 6.
PAGE 70
CAUTION: There is no undo for this command.
PAGE 71
* Warning - Restoring factory defaults will delete the existing * * persistent settings (stacking, fanout, etc.) * * All the units in the stack will be split into standalone units. * * After restoration the unit(s) will be powercycled immediately.
PAGE 72
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series and E-Series.
PAGE 73
SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 74
Command Fields Field Description size(b) Lists the size (in bytes) of the storage location. If the location is remote, no size is listed. Free(b) Lists the available size (in bytes) of the storage location. If the location is remote, no size is listed. Feature Displays the formatted DOS version of the device. Type Displays the type of storage. If the location is remote, the word network is listed. Flags Displays the access available to the storage location.
PAGE 75
Version Description E-Series Original command. Example Usage Information NOTE: A filepath that contains a dot ( . ) is not supported. show running-config Display the current configuration and display changes from the default values.
PAGE 76
File Management isis for the current ISIS configuration line for the current line configuration lldp for the current LLDP configuration load-balance for the current port-channel load-balance configuration logging for the current logging configuration mac for the current MAC ACL configuration mac-addresstable for the current MAC configuration management-eis for the current management EIS configuration managementroute for the current Management port forwarding configuration mld for the
PAGE 77
tacacs+ for the current TACACS+ configuration tftp for the current TFTP configuration trace-group for the current trace-group configuration trace-list for the current trace-list configuration uplink-stategroup for the uplink state group configuration users for the current users configuration vlt for the current VLT configuration wred-profile for the current wred-profile configuration configured (OPTIONAL) Enter the keyword configuration to display line card interfaces with non-default confi
PAGE 78
Example DellEMC# show running-config Current Configuration ... ! Version 9-0(2-0) ! Last configuration change at Thu Apr 18 10:18:39 2013 by admin ! Startup-config last updated at Thu Apr 18 10:18:40 2013 by admin ! boot system stack-unit 1 primary system: A: boot system stack-unit 1 secondary tftp://10.16.127.35/Dell-SI-9-0-2-0.bin boot system stack-unit 1 default system: A: boot system gateway 10.16.132.
PAGE 79
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to include the last configuration change, start-up last updated (date and time), and who made the change.
PAGE 80
Command Fields Version Description E-Series Original command. Lines Description Beginning With Dell EMC Network... Name of the operating system Dell EMC Operating... OS version number Dell EMC Application... Software version Copyright (c)... Copyright information Build Time... Software build’s date stamp Build Path... Location of the software build files loaded on the system Dell EMC Networking OS uptime is... Amount of time the system has been up System image...
PAGE 81
A: | B: Enter the partition to upgrade from the flash. stack-unit: Enter the keywords stack-unit: to synch the image to the stack-unit. file-url Enter the following location keywords and information to upgrade using an Dell EMC Networking OS image other than the one currently running: • • • • To specify an Dell EMC Networking OS image on the internal flash, enter flash:// file-path/filename. To specify an Dell EMC Networking OS image on an FTP server, enter ftp:// user:password@hostip/filepath.
PAGE 82
12946259 bytes successfully copied DellEMC# reload DellEMC# upgrade system Upgrade the Dell EMC Networking OS image. To upgrade the boot flash or boot selector image, use the upgrade boot command. Syntax upgrade system {flash: | ftp: | nfsmount: | scp: | stack-unit {stack-unit-id | all} | tftp: | usbflash:} file-url {A: |B:} Parameters system Enter the keyword system to upgrade the operating system (OS) image.
PAGE 83
Version Description 9.7(0.0) Added support for NFS mount. 9.2(1.0) Introduced on the Z9500. 9.0(0.0) Added support for IPv6 for the file-url parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series.
PAGE 84
Example DellEMC# upgrade system tftp://10.11.8.12/dv-rainier-13 a: 00:39:32 : Discarded 1 pkts. Expected block num : 51. Received block num: 50 !00:39:36 : Discarded 1 pkts. Expected block num : 65. Received block num: 64 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!....... ...........!!!!!!!!!!!!!!!!!!!!!!! 93924044 bytes successfully copied System image upgrade completed successfully.
PAGE 85
4 Control and Monitoring asf-mode Enable alternate store and forward (ASF) mode and forward packets as soon as a threshold is reached. Syntax asf-mode stack-unit {unit-id | all} queue size To return to standard Store and Forward mode, use the no asf-mode command. Parameters unit-id Enter the stack member unit identifier of the stack member to reset. queue size Enter the queue size of the stack member. The range is from 0 to 15.
PAGE 86
banner exec Configure a message that is displayed when your enter EXEC mode. Syntax banner exec c line c To delete a banner, use the no banner exec command. Parameters c Enter the keywords banner exec, then enter a character delineator, represented here by the letter c. Press ENTER. line Enter a text string for your banner message ending the message with your delineator. In the following example, the delineator is a percent character (%); the banner message is “testing, testing”.
PAGE 87
Dell con0 now available Press RETURN to get started. 2d18h2m: %STKUNIT1-M:CP %SEC-5-LOGIN_SUCCESS: Login successful on console This is the banner DellEMC> Related Commands • line — enables and configures the console and virtual terminal lines to the system. banner login Set a message of the day banner to appear after logging on to the system. Syntax banner login {acknowledgement | keyboard-interactive | c line c} Enter no banner login to delete the banner text.
PAGE 88
Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command Usage Information Enter the banner login command, type one or more spaces and a delineator character, type the banner text, and then type the second delineator character. The message of the day banner displays first when you are connected to the router; otherwise the login banner and prompt appear. After you have logged in, the banner EXEC (if configured) displays.
PAGE 89
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 90
cam-acl {default | l2acl number ipv4acl number ipv6acl number, ipv4qos number l2qos numberl2ptnumbe r ipmacacl number ecfmacl number [vman-qos | vman-dual-qos number} Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal to 13. The ipv6acl range must be a factor of 2. Enter 4 or 8 for the number of OpenFlow FP blocks.
PAGE 91
cam-acl-vlan Specify the number of VFP blocks allocated to OpenFlow. Syntax cam-acl-vlan {default | vlanopenflow {0|1}} Defaults Disabled. Parameters default Reset VLAN CAM ACL entries to default settings vlanopenflow Enter the number 1 to allocate VFP blocks and enable OpenFlow. (Default) Enter the number 0 to disable OpenFlow. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 92
clear line Reset a terminal line. Syntax clear line {line-number | console 0 | vty number} Parameters line-number Enter a number for one of the 12 terminal lines on the system. The range is from 0 to 11. aux 0 Enter the keywords aux 0 to reset the auxiliary port. console 0 Enter the keywords console 0 to reset the console port. vty number Enter the keyword vty then a number to clear a terminal line. The range is from 0 to 9.
PAGE 93
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 94
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 95
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 96
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Users entering EXEC Privilege mode or any other configured privilege level can access configuration commands.
PAGE 97
Version Description 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. Usage Information To enable polling and to configure the polling frequency, use this command. enable xfp-power-updates Enable 10–gigabit small form-factor pluggable (XFP) power updates for SNMP. Syntax Parameters enable xfp-power-updates interval seconds interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds.
PAGE 98
• • • • • • • Command History Related Commands PREFIX-LIST AS-PATH ACL COMMUNITY-LIST ROUTER OSPF ROUTER RIP ROUTER ISIS ROUTER BGP This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 99
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 100
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 101
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. morpheus% ftp 10.31.1.111 Connected to 10.
PAGE 102
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 103
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 104
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information The hostname is used in the prompt. ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command.
PAGE 105
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 106
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 107
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 108
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information Configure a password with the ip ftp password command.
PAGE 109
ip telnet server enable Enable the Telnet server on the switch. Syntax ip telnet server enable To disable the Telnet server, use the no ip telnet server enable command. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 110
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 111
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.
PAGE 112
Example Dell(conf)# ip telnet vrf vrf1 Dell(conf)# do telnet 10.10.10.2 Dell(conf)# no ip telnet vrf vrf1 Dell(conf)# ip tftp source-interface Assign an interface’s IP address in outgoing packets for TFTP traffic. Syntax ip tftp source-interface interface To return to the default setting, use the no ip tftp source-interface interface command.
PAGE 113
ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TFTP client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 114
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 115
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. Usage Information You must have either the System Administrator or Security Administrator privileges to configure login concurrentsession limit or to enable clear-line.
PAGE 116
• show login statistics — displays login statistics of users who have used the console or virtual terminal lines to log in to the system. login statistics Enable and configure user login statistics on console and virtual terminal lines. Syntax login statistics {enable | time-period days} no login statistics {enable | time-period days} Parameters enable Enables login statistics for the last 30 days by default.
PAGE 117
There were 1 successful login attempt(s) for user admin in the last 30 day(s). The preceding message shows that the user had previously logged in to the system using the VTY line from 10.11.178.14. It also displays the number of unsuccessful login attempts since the last login and the number of unsuccessful login attempts in the last 30 days. $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'.
PAGE 118
Version Description 8.1.1.0 Introduced on the E-Series 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command ping Test connectivity between the system and another device by sending echo requests and waiting for replies.
PAGE 119
outgoing-interface (IPv6 link-local address) Enter the outgoing interface for ping packets to a destination link-local address. pattern pattern (IPv4 only) Enter the IPv4 data pattern. Range: 0-FFFF. Default: 0xABCD. sweep-min-size Enter the minimum size of datagram in sweep range. The range is from 52 to 15359 bytes. sweep-max-size Enter the maximum size of datagram in sweep range. The range is from 53 to 15359 bytes. sweep-interval Enter the incremental value for sweep size.
PAGE 120
Version Description 8.2.1.0 Introduced on the E-Series (IPv6). 8.1.1.0 Introduced on the E-Series (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for IPv6 address on the E-Series.
PAGE 121
Parameters conditional nvram- (OPTIONAL) Reload into the Dell EMC Networking Operating System (OS) if the cfg-change condition is true. A configuration change to the NVRAM requires a switch reload. To reload the switch, select nvram-cfg-change. no-confirm [discard-running] Reload the chassis without prompting for further confirmation. dell-diag (OPTIONAL) Reload the system into the Dell diagnostics mode. onie (OPTIONAL) Reload the system into the ONIE mode.
PAGE 122
Example Example DellEMC# reload Verified startup-configuration is enabled, Hash for startup-configuration is invalid. Please update Hash for the startup-configuration before reload.
PAGE 123
warmboot Reloads using the warmboot mode Defaults normal-reload Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced on the S3048-ON, S4048–ON, S4048T-ON, S6000–ON, S6100–ON, and Z9100–ON Usage Information Once you enter reload-type, you need to enter the boot-type required on the next reboot.
PAGE 124
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 125
uptime (OPTIONAL) Enter the keyword uptime to have the timestamp based on time elapsed since system reboot. utc (OPTIONAL) Enter the keyword utc to include the UTC time format (ignoring local time zone) in the timestamp. Defaults • • Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. datetime [localtime] datetime Version Description 9.14(1.
PAGE 126
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example EXEC EXEC Privilege Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 127
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 9.1.(0.0) Introduced on S4810. Version 8.3.19.0 Introduced on the S4820T.
PAGE 128
Usage Information One trace log message is generated for each command. No password information is saved to this file. A command-history trace log is saved to a file after failover. Dell EMC Networking TAC analyzes this file to help identify the root cause of it. The timestamps display format of the show command-history output changes based on the service timestamps log datetime configuration. The time format can be in uptime, local time or UTC time.
PAGE 129
DellEMC(conf)#no service timestamps log DellEMC# show command-history [May 17 15:53:44]: CMD-(CLI):[show logging]by default from console [May 17 15:53:53]: CMD-(CLI):[show command-history]by default from console [May 17 15:54:54]: CMD-(CLI):[end]by default from console [May 17 15:55:00]: CMD-(CLI):[show logging]by default from console [May 17 15:55:12]: CMD-(CLI):[show clock]by default from console [May 17 15:55:22]: CMD-(CLI):[show running-config]by default from console [May 17 15:55:27]: CMD-(CLI):[show c
PAGE 130
aaa authentication enable command usage:1 WORD option usage: 1 default option usage: 0 enable option usage: 0 line option usage: 0 none option usage: 0 radius option usage: 1 tacacs+ option usage: 0 Dell# show cpu-traffic-stats View the CPU traffic statistics. Syntax show cpu-traffic-stats [port number | all | cp ] Parameters port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568.
PAGE 131
NOTE: After debugging is complete, use the no debug cpu-traffic-stats command to shut off traffic statistics collection.
PAGE 132
Example DellEMC# show debug Generic IP: IP packet debugging is on for ManagementEthernet 1/1 Port-channel 1-2 Port-channel 5 tenGigabitEthernet 4/1-4/3,4/5-4/6,4/10-4/11,20 TenGigabitEthernet 5/1-5/3,5/5-5/6,5/10-5/11,15,17,19,21 ICMP packet debugging is on for TenGigabitEthernet 5/1,5/2,5/4,5/6,5/8,5/10,5/12,5/14,5/16 DellEMC# show environment View system component status (for example, temperature or voltage).
PAGE 133
Version Description 7.8.1.0 The output of the show environment fan command for the S Series is changed to display fan speeds instead of showing the fan status as up or down. Usage Information The following example shows the output of the show environment command.
PAGE 134
NOTE: This parameter is available but not supported in Dell EMC Networking Operating System version 8.3.11.4. Because stacking is not supported, if you use this parameter, the output displays “Media not present or accessible” (refer to the Usage Information section). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 135
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Example (S4048T–ON) 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49/1 49/2 49/3 49/4 50 51 52 53 54 SFP SFP SFP SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP+ SFP SFP+ SFP+ SFP+ QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 1000BASE-SX 1000BASE-SX 1000BASE-SX Media not present or 10GBASE-CU2M 10GBASE-CU2M Media not present o
PAGE 136
1 1 1 1 1 1 1 1 1 1 1 1 52/1 52/2 52/3 52/4 53/1 53/2 53/3 53/4 54/1 54/2 54/3 54/4 QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP 40GBASE-SR4 40GBASE-SR4 40GBASE-SR4 40GBASE-SR4 40GBASE-CR4-7M 40GBASE-CR4-7M 40GBASE-CR4-7M 40GBASE-CR4-7M 40GBASE-CR4-1M 40GBASE-CR4-1M 40GBASE-CR4-1M 40GBASE-CR4-1M 7503835T00L3 7503835T00L3 7503835T00L3 7503835T00L3 CN005RH02BF6396 CN005RH02BF6396 CN005RH02BF6396 CN005RH02BF6396 APF122000140DK APF122000140DK APF122000140DK APF122000140DK Yes Yes Yes DellE
PAGE 137
To view the successful and failed login details of all users in the last 30 days or the custom defined period, use the show login statistics all command. You can use this command only if you have system or security administrator rights. To view the successful and failed login details of a specific user in the last 30 days or the custom defined time period, use the show login statistics user user-id command.
PAGE 138
-----------------------------------------------------------------User: admin Last login time: 12:52:01 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.143 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 0 Successful login attempt(s) in last 30 day(s): 1 -----------------------------------------------------------------The following is sample output of the show login statistics unsuccessful-attempts command.
PAGE 139
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced this version of the command for the S-Series. Usage Information The output for show memory displays the memory usage of LP part (sysdlp) of the system. The sysdlp is an aggregate task that handles all the tasks running on the S-Series’ CPU.
PAGE 140
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the keywords management-unit [details]. 7.6.1.0 Introduced on the S-Series.
PAGE 141
53 60 6 10000 0.00% 0.00% 0.00% 0 52 0 0 0 0.00% 0.00% 0.00% 0 51 0 0 0 0.00% 0.00% 0.00% 0 portmirr cfgDataSync sysCompMgr statMgr sflCp snmp dpi_cmow dpi_taskcmo 50 50 5 10000 0.00% 0.01% 0.00% 0 49 1010 101 10000 0.05% 0.07% 0.08% 0 48 30 3 10000 0.00% 0.00% 0.00% 0 47 0 0 0 0.00% 0.00% 0.00% 0 46 0 0 0 0.00% 0.00% 0.
PAGE 142
• Command History Usage Information EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 143
• If no response is received within a defined period of time, the SWP timeout mechanism resubmits the message at the head of the FIFO queue. After retrying a defined number of times, the SWP-2-NOMORETIMEOUT timeout message is generated. In the S-Series example, a retry (Retries) value of zero indicates that the SWP mechanism reached the maximum number of retransmissions without an acknowledgement.
PAGE 144
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.7.1.0 Added the management-unit option. 7.6.1.0 Introduced on the S-Series.
PAGE 145
tFib4 1943960 aclAgent 90770 ifagt_1 21318 dsagt 6504 MacAgent 269778 DellEMC# Example (managementunit) 0 16564 16564 0 0 1943960 1943960 74206 74206 21318 4754 6504 6504 269778 269778 DellEMC# show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249856 50572 0 50572 50572 323 fr
PAGE 146
Usage Information You can use the show reset-reason without the stack-unit option to view the reason for the last system reboot of the local system. Example — Userinitiated reboot with the reload command DellEMC#show reset-reason Cause : Reset by User through CLI command Reset Time: 11/05/2017-08:36 Example — System reboot due to the upgrade command DellEMC# show reset-reason Cause: Reboot by Software upgrade Module. Reset Time: 8/9/2017 1:39 PM.
PAGE 147
show software ifm Display interface management (IFM) data. Syntax Parameters show software ifm {clients [summary] | ifagt number | ifcb interface | stackunit unit-ID | trace-flags} clients Enter the keyword clients to display IFM client information. summary (OPTIONAL) Enter the keyword summary to display brief information about IFM clients. ifagt number Enter the keyword ifagt then the number of an interface agent to display software pipe and IPC statistics.
PAGE 148
ACL 0 0x00000000 0x00000000 0x867f50c3 0x000f0218 44 OSPF 0 0x00000dfa 0x00400098 0x00000000 0x00000000 0 PIM 0 0x000000f3 0x00030000 0x00000000 0x00000000 0 IGMP 0 0x000e027f 0x00000000 0x00000000 0x00000000 0 SNMP 0 0x00000000 0x00000000 0x800302c0 0x00000002 30 EVTTERM 0 0x00000000 0x00000000 0x800002c0 0x00000000 29 MRTM 0 0x00000000 0x00000200 0x81f7103f 0x00000000 38 DSM 0 0x00000000 0x00000000 0x80771003 0x00000000 32 LACP 0 0x00000000 0x00000000 0x8000383f 0x00000000 35 DHCP 0 0x00000000 0x00000000
PAGE 149
Version Description 7.7.1.0 Added Master Priority field. 7.6.1.0 Introduced on the S-Series. Example (show system brief) Example (4048TON) DellEMC#show system stack-unit 1 -- Unit 1 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S4048T-ON - 48x10G, 6x40G TE/FO G (S4048T-ON) Current Type : S4048T-ON - 48x10G, 6x40G TE/FO G (S4048T-ON) Master priority : 0 Hardware Rev : 1.0 Num Ports : 72 Up Time : 4 day, 20 hr, 6 min Dell EMC Networking OS Version : 9.13(0.
PAGE 150
Num Ports : 72 Up Time : 2 day, 20 hr, 49 min Dell EMC Networking OS Version : 9.13(0.0) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : 3.21.2.9 Boot Selector : 3.21.0.
PAGE 151
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 152
| Pipe through a DellEMC# show tech-support except Show only text find Search for the grep Show only text no-more Don't paginate save Save output to command stack-unit 1 | ? that does not match a pattern first occurrence of a pattern that matches a pattern output a file DellEMC# show tech-support stack-unit 1 | save ? flash: Save to local file system (flash://filename (max 20 chars) ) DellEMC# show tech-support stack-unit 1 | save flash://LauraSave Start saving show command report .......
PAGE 153
FPGA IMAGE INFORMATION : --------------------------------------------------------------------Card FPGA Name Version stack-unit 1 S4048-ON SYSTEM CPLD 15.2 stack-unit 1 S4048-ON MASTER CPLD 12 stack-unit 1 S4048-ON SLAVE CPLD 5 ----------------------------------- show revision -------------------------------- Stack unit 1 -S4048-ON SYSTEM CPLD S4048-ON MASTER CPLD S4048-ON SLAVE CPLD : 15.2 : 12 : 5 ------------------------------------ show clock ------------------------------08:10:51.
PAGE 154
Card stack-unit 1 stack-unit 1 FPGA Name S4048TON SYSTEM CPLD S4048TON MASTER CPLD Version 12 13 ----------------------------------- show revision -------------------------------- Stack unit 1 -S4048TON SYSTEM CPLD S4048TON MASTER CPLD : 12 : 13 ------------------------------------ show clock ------------------------------05:15:31.
PAGE 155
ssh-peer-stack-unit Open an SSH connection to the peer stack-unit. Syntax Parameters ssh-peer-stack-unit [-l username] -l username (OPTIONAL) Enter the keyword -l then your user name. The default is the user name associated with the terminal. Defaults Not configured. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.
PAGE 156
• • • • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a Null interface, enter the keyword null then the Null interface number. For a port channel interface, enter the keywords port-channel then a number.
PAGE 157
In case there is a mismatch between the VRF telnet source interface and the telnent VRF, then an error is reported. Example DellEMC# telnet vrf vrf1 10.10.10.2 telnet-peer-stack-unit Open a Telnet connection to the peer stack unit. Syntax telnet-peer-stack-unit Defaults Not configured. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 158
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 159
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.2.1.
PAGE 160
----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 100::1 000.000 ms 000.000 ms 000.000 ms DellEMC#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 3ffe:501:ffff:100:201:e8ff:fe00:4c8b, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 3ffe:501:ffff:100:201:e8ff:fe00:4c8b 000.000 ms 000.000 ms 000.
PAGE 161
virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6-address} command. Parameters ipv4-address Enter the IP address of the active management interface in a dotted decimal format (A.B.C.D.). ipv6-address Enter an IPv6 address of the active management interface, in the x:x:x:x::x format.
PAGE 162
Parameters memory Enter the keyword memory to copy the current running configuration to the startup configuration file. This command is similar to the copy running-config startupconfig command. compressed Enter the keyword compressed to write the operating configuration to the startupconfig file in the compressed mode. terminal Enter the keyword terminal to copy the current running configuration to the terminal. This command is similar to the show running-config command.
PAGE 163
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell EMC Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 164
debug dot1x Display 802.1X debugging information. Syntax debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] Parameters all Enable all debugs in dot1x. auth-pae-fsm Enable Authentication PAE FSM debugs in dot1x. backend-fsm Enable Backend Auth FSM debugs in dot1x. eapol-pdu Enable EAPOL frame trace in dot1x. interface interface Restricts the debugging information to an interface.
PAGE 165
Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 166
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 167
• • Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command). In MAB-only authentication mode, a port authenticates using the host MAC address even though 802.1xauthentication is enabled. If the MAB-only authentication fails, the host is placed in the guest VLAN (if configured). To disable MAB-only authentication on a port, enter the no dot1x auth-type mab-only command.
PAGE 168
To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 169
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series.
PAGE 170
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.
PAGE 171
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series. Usage Information To disable MAC authentication bypass on a port, enter the no dot1x mac-auth-bypass command.
PAGE 172
dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode. Syntax dot1x max-supplicants number Parameters number Enter the number of supplicants that can be authenticated on a single port in Multi-auth mode. The range is from 1 to 128. The default is 128. Defaults 128 hosts can be authenticated on a single authenticator port.
PAGE 173
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 174
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command.
PAGE 175
To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 176
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.
PAGE 177
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 178
Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. show dot1x cos-mapping interface Display the CoS priority-mapping table the RADIUS server provides and applies to authenticated supplicants on an 802.1X-enabled system.
PAGE 179
802.1p CoS re-map table on Te 1/32: ---------------------------------Dot1p Remapped Dot1p 0 7 1 6 2 5 3 4 4 3 5 2 6 1 7 0 DellEMC# DellEMC# show dot1x cos-mapping interface tengigabitethernet 1/32 macaddress 00:00:00:00:00:10 Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.1p CoS re-map table on Te 1/32: ---------------------------------802.1p CoS re-map table for Supplicant: 00:00:00:00:00:10 Dot1p 0 1 2 3 4 5 6 7 DellEMC# Remapped Dot1p 7 6 5 4 3 2 1 0 show dot1x interface Display the 802.
PAGE 180
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added the mac-address option on the C-Series and S-Series. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. Usage Information If you enable 802.
PAGE 181
Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:10 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: DellEMC# AUTHORIZED(MAC-AUTH-BYPASS) 400 Authenticated Idle DellEMC# show dot1x interface tengigabitethernet 1/32 mac-address 00:00:00:00:00:11 Supplicant Mac: 0 0 0 0 0 10
PAGE 182
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell EMC Networking OS.
PAGE 183
• • • • • • • • • • • • • permit tcp (for Extended IP ACLs) seq arp (for Extended MAC ACLs) seq ether-type (for Extended MAC ACLs) seq (for IP ACLs) seq (for IPv6 ACLs) permit udp (for IPv6 ACLs) permit tcp (for IPv6 ACLs) permit icmp (for IPv6 ACLs) permit (for IPv6 ACLs) deny udp (for IPv6 ACLs) deny tcp (for IPv6 ACLs) deny icmp (for Extended IPv6 ACLs) deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each ACL mode and do not have mode-specific options.
PAGE 184
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. Usage Information The remark command is available in each ACL mode.
PAGE 185
show config Display the current ACL configuration. Syntax show config Command Modes • • • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example CONFIGURATION-STANDARD-ACCESS-LIST CONFIGURATION-EXTENDED-ACCESS-LIST CONFIGURATION-MAC ACCESS LIST-STANDARD CONFIGURATION-MAC ACCESS LIST-EXTENDED Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 186
access-class Apply a standard ACL to a terminal line. Syntax access-class access-list-name [ipv4 | ipv6] To remove an ACL, use the no access-class command. Parameters access-list-name Enter the name of a configured Standard ACL, up to 140 characters. ipv4 Enter the keyword ipv4 to configure an IPv4 access class. ipv6 Enter the keyword ipv6 to configure an IPv6 access class. Defaults Not configured. Command Modes LINE Command History This guide is platform-specific.
PAGE 187
Similarly, if you have configured either IPv4 or IPv6 specific filtering on a terminal line, you cannot apply generic IP ACLs on top of this configuration. Before applying the generic ACL configuration, first undo the existing configuration using the no access-class access-list-name [ipv4 | ipv6] command. clear counters ip access-group Erase all counters maintained for access lists.
PAGE 188
out Enter the keyword out to apply the ACL to outgoing traffic. implicit-permit (OPTIONAL) Enter the keyword implicit-permit to change the default action of the ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). vlan vlan-id (OPTIONAL) Enter the keyword vlan then the ID numbers of the VLANs. The range is from 1 to 4094 (you can use IDs from 1 to 4094).
PAGE 189
NOTE: If you apply outbound(egress) IP acl on a switch port, the filter applies only for routed traffic egressing out of that port. To associate an access-list to a non-default VRF, use the vrf attribute of this command. You can use this command at the interface context (physical/LAG) to apply the access-list to a range of VRFs. The VRF MODE is not available for the default and management VRFs. In the Dell EMC Networking OS versions prior to 9.13(0.
PAGE 190
Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 191
Usage Information Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 192
Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters. interface interface Enter the keyword interface followed by the one of the following keywords and slot/ port or number information: • • • • For a VLAN interface, enter the keyword vlan followed by the slot/port number. For a Port Channel interface, enter the keyword port-channel followed by a number.
PAGE 193
count (OPTIONAL) Enter the keyword count to count the packets. bytes (OPTIONAL) Enter the keyword bytes to count the bytes. log (OPTIONAL) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match the IP DSCP values. The range is from 0 to 63. ecn (OPTIONAL) Enter the keyword ecn to match the ECN bits. The range is from 0 to 3. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry.
PAGE 194
Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the Quality of Service section in the Dell EMC Networking OS Configuration Guide.
PAGE 195
Version Description 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. Usage Information Dell EMC Networking OS supports one ingress and one egress IP ACL per interface. Prior to Dell EMC Networking OS version 7.8.1.0, names are up to 16 characters long. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation.
PAGE 196
Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Removed the session–ID option from the monitor parameter. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 197
Defaults None Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 198
host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname. count (OPTIONAL) Enter the keyword count to count packets the filter processes. bytes (OPTIONAL) Enter the keyword bytes to count bytes the filter processes. log (OPTIONAL) Enter the keyword log to enter ACL matches in the log. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. The range is from 0 to 63. ecn (OPTIONAL) Enter the keyword ecn to match to the ECN values.
PAGE 199
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. The following applies: • • • • • Related Commands • • The seq sequence-number command is applicable only in an ACL group.
PAGE 200
ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: • • • • • eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 201
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the noncontiguous mask and added the monitor option. 6.5.1.
PAGE 202
operator Enter one of the following logical operand: • • • • • eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value.
PAGE 203
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 204
• • • • • • operator (OPTIONAL) Enter one of the following logical operand: • • • • • port port ack: acknowledgement field fin: finish (no more data from the user) psh: push function rst: reset the connection syn: synchronize sequence numbers urg: urgent field eq = equal to neq = not equal to gt = greater than lt = less than range = inclusive range of ports (you must specify two ports for the port command) Enter the application layer port number.
PAGE 205
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 206
Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To 1 0000000000000000 1111110000000000 0 #Covered 1023 1024 Total Ports: 1024 Related Commands • • deny — assign a filter to deny IP traffic. deny udp — assign a filter to deny UDP traffic. deny udp To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 207
destination Enter the IP address of the network or host to which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 208
Version Description 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the Quality of Service section of the Dell EMC Networking OS Configuration Guide. The monitor option is relevant in the context of flow-based monitoring only.
PAGE 209
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.
PAGE 210
host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname. destination Enter the IP address of the network or host to which the packets are sent. ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: • • • • • eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value.
PAGE 211
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 212
ttl Enter the keyword ttl to permit a packet based on the time to live value. The range is from 1 to 255. operator Enter one of the following logical operand: • • • • • eq(equal to) — matches packets that contain a ttl value that is equal to the specified ttl value. neq(not equal to) — matches packets that contain a ttl value that is not equal to the specified ttl value. gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value.
PAGE 213
Version Description 9.12(0.0) Introduced the ttl parameter. Removed the session–ID option from the monitor parameter. 9.11(2.0P0) Added the established parameter on the S6000, S6000–ON, S6100–ON, Z9100– ON. 9.11(0.0) Added support for session–ID to the monitor parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 214
4 5 6 7 8 0001100000000000 0001110000000000 0001111000000000 0001111100000000 0001111101000000 1111110000000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 6144 7168 7680 7936 8000 7167 7679 7935 7999 8000 1024 512 256 64 1 Total Ports: 4001 Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM.
PAGE 215
• • • • neq = not equal to gt = greater than lt = less than range = inclusive range of ports (you must specify two ports for the port parameter) port port Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is 0 to 65535. destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter.
PAGE 216
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. . 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell EMC Networking OS Configuration Guide.
PAGE 217
Step-toIncrement Enter the step to increment the sequence number. The range is from 1 to 4294967290. Defaults None Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 218
tcp Enter the keyword tcp to configure a TCP access list filter. udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 219
monitor (OPTIONAL) Enter the keyword monitor then the session–ID to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. The session–ID range is from 0 to 65535. NOTE: For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell EMC Networking OS Configuration Guide. fragments Enter the keyword fragments to use ACLs to control packet fragments.
PAGE 220
• • • • • The seq sequence-number command is applicable only in an ACL group. The order option works across ACL groups that are applied on an interface via the QoS policy framework. The order option takes precedence over seq sequence-number. If you do not configure sequence-number, the rules with the same order value are ordered according to their configuration order. If you configure sequence-number, the sequence-number is used as a tie breaker for rules with the same order.
PAGE 221
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. mac access-group Apply a MAC ACL to traffic entering or exiting an interface. You can apply a MAC ACL on a physical, port-channel, or VLAN interface.
PAGE 222
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 223
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.1.0 Introduced. show mac accounting access-list Display MAC access list configurations and counters (if configured).
PAGE 224
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series 6.1.1.0 Introduced on the E-Series.
PAGE 225
monitored interface. For more information, see the “Flow-based Monitoring” in the Port Monitoring section in the Dell EMC Networking OS Configuration Guide. Defaults Not enabled. Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 226
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 227
mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match). count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. log (OPTIONAL) Enter the keyword log to include ACL messages in the log.
PAGE 228
seq To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Use the no seq sequence-number command if you know the filter’s sequence number. Use the no deny {any | mac-source-address mac-source-address-mask} command.
PAGE 229
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. Usage Information When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details.
PAGE 230
The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. ethertype operator (OPTIONAL) To filter based on protocol type, enter one of the following Ethertypes: count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter.
PAGE 231
Usage Information When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands • • permit — configure a MAC address filter to pass packets.
PAGE 232
Example Related Commands DellEMC(conf)# mac-access-list access-list extended TestMATExt DellEMC(config-ext-macl)# remark 5 IPv4 DellEMC(config-ext-macl)# seq 10 permit any any ev2 eq 800 count bytes DellEMC(config-ext-macl)# remark 15 ARP DellEMC(config-ext-macl)# seq 20 permit any any ev2 eq 806 count bytes DellEMC(config-ext-macl)# remark 25 IPv6 DellEMC(config-ext-macl)# seq 30 permit any any ev2 eq 86dd count bytes DellEMC(config-ext-macl)# seq 40 permit any any count bytes DellEMC(config-ext-macl)# e
PAGE 233
byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to log the packets. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. NOTE: For more information, see Flow-based Monitoring in the “Port Monitoring” section of the Dell EMC Networking OS Configuration Guide.
PAGE 234
clear ip prefix-list Reset the number of times traffic mets the conditions (“hit” counters) of the configured prefix lists. Syntax clear ip prefix-list [prefix-name] Parameters prefix-name (OPTIONAL) Enter the name of the configured prefix list to clear only counters for that prefix list, up to 140 characters long. Defaults Clears “hit” counters for all prefix lists unless a prefix list is specified. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 235
le max-prefix- length (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32. Defaults Not configured. Command Modes PREFIX-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 236
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 237
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 238
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example DellEMC(conf-nprefixl)# show config ! ip prefix-list snickers DellEMC(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists.
PAGE 239
Example DellEMC# show ip prefix-list detail Ip Prefix-list with the last deletion/insertion: PL_OSPF_to_RIP ip prefix-list PL_OSPF_to_RIP: count: 3, range entries: 1, sequences: 5 - 25 seq 5 permit 1.1.1.0/24 (hit count: 0) seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) DellEMC# show ip prefix-list summary Display a summary of the configured prefix lists.
PAGE 240
Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit. To configure route maps and their redistribution criteria, use the following commands. continue To a route-map entry with a higher sequence number, configure a route-map. Syntax continue [sequence-number] Parameters sequence-number (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Defaults Not configured.
PAGE 241
If the route-map entry contains sets with the continue clause, set actions are performed first then the continue clause jumps to the specified route map entry. • • Related Commands • • If a set action occurs in the first route map entry and then the same set action occurs with a different value in a subsequent route map entry, the last set of actions overrides the previous set of actions with the same set command.
PAGE 242
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 243
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 244
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.
PAGE 245
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 246
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. • • • • • • match interface — redistribute routes that match the next-hop interface.
PAGE 247
Related Commands Version Description 8.3.7.0 Introduced on the S4810 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. • • • • • • match interface — redistribute routes that match the next-hop interface. match ip address — redistribute routes that match an IP address.
PAGE 248
Related Commands Version Description pre-6.1.1.0 Introduced on the E-Series. • • • • • • match interface — redistribute routes that match the next-hop interface. match ip address — redistribute routes that match an IP address. match ip next-hop — redistribute routes that match the next-hop IP address. match ip route-source — redistribute routes that match routes advertised by other routers. match route-type — redistribute routes that match a route type.
PAGE 249
match route-type To match routes based on the how the route is defined, configure a filter. Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command. Parameters external [type-1| type-2] Enter the keyword external then either type-1 or type-2 to match only on OSPF Type 1 routes or OSPF Type 2 routes.
PAGE 250
match tag To redistribute only routes that match a specified tag value, configure a filter. Syntax match tag tag-value To remove a match, use the no match tag command. Parameters tag-value Enter a value as the tag on which to match. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 251
Defaults permit (OPTIONAL) Enter the keyword permit to set the route map default as permit. If you do not specify a keyword, the default is permit. deny (OPTIONAL) Enter the keyword deny to set the route map default as deny. sequence-number (OPTIONAL) Enter a number to identify the route map for editing and sequencing with other route maps. You are prompted for a sequence number if there are multiple instances of the route map. The range is from 1 to 65535. Not configured.
PAGE 252
To remove an AS-Path setting, use the no set as-path {prepend as-number | tag} command. Parameters prepend asnumber Enter the keyword prepend and then enter up to eight AS numbers to be inserted into the BGP path information. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 253
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 254
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 255
none Enter the keyword none to remove the community attribute from routes meeting the route map criteria. additive (OPTIONAL) Enter the keyword additive to add the communities to already existing communities. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 256
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Dell EMC Networking OS Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 257
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 258
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. • • • • set automatic-tag — compute the tag value of the route.
PAGE 259
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. • • • • set automatic-tag — compute the tag value of the route. set level — specify the OSPF area for route redistribution.
PAGE 260
Version Description pre-6.1.1.0 Introduced on the E-Series. Usage Information If you configure the set next-hop command, its configuration takes precedence over the neighbor nexthop-self command in the ROUTER BGP mode. If you configure the set next-hop command with the interface’s IP address (either Loopback or physical), the software declares the route unreachable. Related Commands • match ip next-hop — redistribute routes that match the next-hop IP address.
PAGE 261
set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command. Parameters tag-value Enter a number as the tag. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 262
When there are multiple routes to the same destination, the routes with a higher weight are preferred. Defaults router-originated = 32768; all other routes = 0 Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 263
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 264
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 265
Usage Information To apply the AS-PATH ACL to BGP routes, use the match as-path or neighbor filter-list commands. Example Related Commands DellEMC(conf)# ip as-path access-list TestPath DellEMC(config-as-path)# • match as-path — match on routes contain a specific AS-PATH. show ip as-path-access-lists Display the all AS-PATH access lists configured on the E-Series. Syntax show ip as-path-access-lists Command Modes • • Command History This guide is platform-specific.
PAGE 266
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.
PAGE 267
permit no-export DellEMC# UDF ACL Commands The following commands are available within each UDF ACL mode. deny ip Disassociate the UDF in IP access-list. Syntax deny ip {source mask | any | host ip-address} {destination mask | any | host ip-address} udf-pkt-format name udf-qualifier-value name To remove this filter, use the no seq sequence-number command. Parameters source Enter the IP address of the network or host from which the packets were sent.
PAGE 268
Command Modes Example Command History CONFIGURATION Dell(conf)#feature udf-acl This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S6000, Z9500, and S4048-ON.
PAGE 269
match Configure the packet type to match for which the UDF offset bytes have to be parsed. Syntax match l2ethertype ipv4 ipprotocol value vlantag tagStatus To return to the default settings, use the no match l2ethertype ipv4 ipprotocol value vlantag tagStatus command. Parameters l2ethertype Enter the keyword l2ethertype to match the L2 Ethertype. ipv4 Enter the keyword ipv4 to match the IPv4 packet. ipprotocol value Enter the keyword ipprotocol then the option to match the IPv4 protocol.
PAGE 270
host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. udf-pkt-format Enter the keywords udf-pkt-format then the UDF ACL profile name. name udf-qualifier-value Enter the keywords udf-qualifier-value then the UDF qualifier value profile name.
PAGE 271
To return to the default settings, use the no udf-id 1-12 value mask command. Parameters id Enter the UDF ID range. The range is from 1 to 12. value Enter the value for the UDF in Hex, up to 24 bytes. mask Enter the mask for the UDF in Hex, up to 24 bytes. Defaults None Command Modes CONFIGURATION-UDF-Qualifier-Value Profile Example Command History Dell(conf-udf-tcam-qual-val)#udf-id 1 aa ff This guide is platform-specific.
PAGE 272
udf-tcam Create a context for UDF TCAM. Syntax udf-tcam name seq number To return to the default settings, use the no udf-tcam name seq number command. Parameters name Enter the UDF ACL profile name, up to 64 characters. number Enter the keyword seq then the sequence number of the Udf-Tcam table. The range is from 1 to 512. Defaults None Command Modes CONFIGURATION Example Command History Dell(conf)#udf-tcam ipnip seq 1 This guide is platform-specific.
PAGE 273
Version Description 9.10(0.0) Introduced on the S6100. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 274
• • • log gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 275
and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 276
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 277
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 278
[port]] [count [byte]] [order] [fragments] [log [interval minutes] [thresholdin-msgs [count]] To remove this filter, you have two choices: • • Parameters Use the no seq sequence-number command if you know the filter’s sequence number. Use the no deny udp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. ttl Enter the keyword ttl to deny a packet based on the time to live value. The range is from 1 to 255.
PAGE 279
deny arp (for Extended MAC ACLs) Configure an egress filter that drops ARP packets on egress ACL supported line cards. (For more information, refer to your line card documentation).
PAGE 280
and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 281
Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 282
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 283
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 284
• Parameters Use the no deny {any | host mac-address | mac-source-address mac-sourceaddress-mask} {any | host mac-address | mac-destination-address macdestination-address-mask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate count the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated.
PAGE 285
Related Commands • • permit — configure a MAC address filter to pass packets. seq — configure a MAC address filter with a specified sequence number. permit (for Standard IP ACLs) To permit packets from a specific source IP address to leave the switch, configure a filter.
PAGE 286
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 287
Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 288
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 289
threshold-in msgs (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate count the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 290
permit udp (for Extended IP ACLs) To pass UDP packets meeting the filter criteria, configure a filter. Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [ttl operator] [dscp] [operator port [port]] [count [byte]] [order] [fragments] [log [interval minutes] [thresholdin-msgs [count]][monitor] To remove this filter, you have two choices: • • Parameters Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 291
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 292
log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate count the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 293
• permit udp — assign a permit filter for UDP packets. permit (for Standard MAC ACLs) To forward packets from a specific source MAC address, configure a filter. Syntax permit {any | mac-source-address [mac-source-address-mask]} [count [byte]] | [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 294
You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 295
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 296
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 297
seq arp (for Extended MAC ACLs) Configure an egress filter with a sequence number that filters ARP packets meeting this criteria. This command is supported only on 12port GE line cards with SFP optics. For specifications, refer to your line card documentation. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here.
PAGE 298
and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 299
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, standard and extended IPv6 ACLs, and standard and extended MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 300
Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 301
ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list permits all IP protocols. tcp Enter the keyword tcp to configure a TCP access list filter. udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) .
PAGE 302
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 303
• • log lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 304
for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). permit tcp (for IPv6 ACLs) Configure a filter to pass TCP packets that match the filter criteria.
PAGE 305
• • • gt(greater than) — matches packets that contain a ttl value that is greater than the specified ttl value. lt (less than) — matches packets that contain a ttl value that is less than the specified ttl value. range(inclusive range of values) — matches packets that contain a ttl value that falls between the specified range of ttl values. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes.
PAGE 306
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 307
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
PAGE 308
permit (for IPv6 ACLs) To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP.
PAGE 309
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 310
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 311
host ipv6-address Enter the keyword host then the IP address to specify a host IP address. destination address Enter the IPv6 address of the network or host to which the packets are sent.
PAGE 312
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the ttl parameter. 9.11(2.0P0) Added the established parameter on the on the S6000, S6000–ON, S6100–ON, Z9100–ON. 9.10(0.
PAGE 313
To remove this filter, you have two choices: • • Parameters Use the no seq sequence-number command syntax if you know the filter’s sequence number Use the no deny icmp {source address mask | any | host ipv6-address} {destination address | any | host ipv6-address} command source address mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 314
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.5(0.1) Introduced on the Z9500. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 315
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 316
7 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) member vlan Add VLAN members to an ACL VLAN group. Syntax member vlan {VLAN-range} Parameters VLAN-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination. For example: Comma-separated: 3, 4, 6 Range: 5-10 Combination: 3, 4, 5-10, 8 Default None Command Modes CONFIGURATION (conf-acl-vl-grp) Command History This guide is platform-specific.
PAGE 317
implicit-permit Enter the keyword implicit-permit to change the default action of the ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). Default None Command Modes CONFIGURATION (conf-acl-vl-grp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 318
Group Name Members Test 1-100 Egress IP Acl Ingress IP Acl - Ingress V6 Acl test Vlan - The following sample output is displayed when using the show acl-vlan-group group-name option. NOTE: The access list name is truncated. DellEMC# show acl-vlan-group TestGroupSeventeenTwenty Group Name Egress IP Acl Ingress IP Acl Acl Vlan Members Test test 1-100 Ingress IPV6 The following sample output shows the line-by-line style display when using the show acl-vlan-group detail option.
PAGE 319
Example Field Description Current Settings(in block sizes) Information about the number of FP blocks that are currently in use or allocated. VlanOpenFlow Number of FP blocks for VLAN open flow operations. VlanIscsi Number of FP blocks for VLAN internet small computer system interface (iSCSI) counters. VlanHp Number of FP blocks for VLAN high performance processes. VlanFcoe Number of FP blocks for VLAN Fiber Channel over Ethernet (FCoE) operations.
PAGE 320
enhanced. A total of four VACP groups are present, of which two are for fixed groups and the other two are for dynamic groups. Out of the total of two dynamic groups, you can allocate zero, one, or two flow processor (FP) blocks to iSCSI Counters, OpenFlow and ACL Optimization. You can configure only two of these features at a point in time. show cam-usage View the amount of CAM space available, used, and remaining in each partition (including IPv4 Flow and Layer 2 ACL sub-partitions).
PAGE 321
| | OUT-L3 ACL | | OUT-V6 ACL 2 | 0 | IN-L2 ACL | | IN-L3 ACL | | IN-L3 FIB | | IN-V6 ACL | | IN-NLB ACL | | IPMAC ACL | | OUT-L2 ACL | | OUT-L3 ACL | | OUT-V6 ACL 3 | 0 | IN-L2 ACL | | IN-L3 ACL | | IN-L3 FIB | | IN-V6 ACL | | IN-NLB ACL | | IPMAC ACL | | OUT-L2 ACL | | OUT-L3 ACL | | OUT-V6 ACL Codes: * - cam usage is above 90%.
PAGE 322
Example 4: Output of the show camusage switch Command DellEMC#show cam-usage switch Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|=================|=============|=============| ============== 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 2 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 3 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 Codes: * - cam usage is above 90%.
PAGE 323
Parameters group-name Specify the name of the ACL VLAN group. The name can contain a maximum 140 characters. Default No default behavior or values Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.
PAGE 324
Examples The following sample output shows the line-by-line style display when using the show acl-vlan-group detail option. Note that no group or access list names are truncated DellEMC# show acl-vlan-group detail Group Name : Test Egress IP Acl : Ingress IP Acl : test Ingress IPV6 Acl : Vlan Members : 1-100 DellEMC# description (ACL VLAN Group) Add a description to the ACL VLAN group.
PAGE 325
8 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 326
ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Introduced support for enabling BFD on non-default VRFs for IPv4 BGP, default, and nondefault VRFs for IPv6 BGP on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, C9010, Z9500, and Z9100–ON. 9.11(2.
PAGE 327
NOTE: The bfd all-neighbors command is applicable for both IPv4 and IPv6 BGP sessions. bfd enable (Configuration) Enable BFD on all interfaces. Syntax bfd enable Disable BFD using the no bfd enable command. Defaults BFD is disabled by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 328
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd interval Specify non-default BFD session parameters beginning with the transmission interval.
PAGE 329
Example DellEMC(conf-if-te-1/3)# bfd interval 250 min_rx 300 multiplier 4 role passive DellEMC(conf-if-te-1/3)# bfd protocol-liveness Enable the BFD protocol liveness feature. Syntax bfd protocol-liveness Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 330
multiplier value Enter the keywords multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3. role [active | passive] Enter the role that the local system assumes: • • Active — active system initiates the BFD session. Both systems can be active for the same session. Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system.
PAGE 331
prefix-list prefix- list-name interval milliseconds min_rx milliseconds (Optional) Enter the keyword prefix-list followed by the name of the prefix list to enable or disable BFD on specific IPv6 neighbors. (OPTIONAL) Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 200.
PAGE 332
• • Active — active system initiates the BFD session. Both systems can be active for the same session. Passive — passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is Active. Defaults See Parameters. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.
PAGE 333
The default is Active. Defaults See Parameters. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.
PAGE 334
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.2.1.
PAGE 335
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series.
PAGE 336
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Added support for BFD for BGP on the S4810. 8.4.1.3 Added support for BFD for BGP on the E-Series. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for BFD for VLAN and port-channel interfaces on the E-Series. 7.4.1.
PAGE 337
Example (Detail) The following example shows the show bfd vrf neighbors detail command output showing the nondefault VRF called “VRF_blue”. show bfd vrf VRF_blue neighbors detail Session Discriminator: 5 Neighbor Discriminator: 3 Local Addr: 5.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 5.1.1.
PAGE 338
Role: Active Delete session on Down: True VRF: VRF_blue Client Registered: OSPF Uptime: 00:00:14 Statistics: Number of packets received from neighbor: 73 Number of packets sent to neighbor: 73 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Related Commands • bfd all-neighbors — establish BFD sessions with all neighbors discovered by the IS-IS protocol or OSPF protocol out of all interfaces.
PAGE 339
9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 340
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for IPv6 VRF. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.5.1.
PAGE 341
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 342
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. ROUTER BGP ROUTER BGP-address-family Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 343
Version Description 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Usage Information Any update without a MED attribute is the least preferred route. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI).
PAGE 344
DellEMC(conf)#do show run | grep bgp router bgp 1 bgp four-octet-as-support bgp asnotation asdot+ DellEMC(conf)#router bgp 1 DellEMC(conf-router_bgp)# bgp asnotation asplain DellEMC(conf-router_bgp)# ex DellEMC(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support DellEMC(conf)# Related Commands • bgp four-octet-as-support — enable 4-byte support for the BGP process. bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations.
PAGE 345
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath as-path multipath-relax command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 346
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The software compares the MEDs only if the path contains no external autonomous system numbers. If you enable this command, use the clear ip bgp * command to recompute the best path.
PAGE 347
bgp bestpath router-id ignore Do not compare router-id information for external paths during best path selection. Syntax bgp bestpath router-id ignore To return to the default selection, use the no bgp bestpath router-id ignore command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 348
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Route reflection to clients is not necessary if all client routers are fully meshed.
PAGE 349
Usage Information When a BGP cluster contains only one route reflector, the cluster ID is the route reflector’s router ID. For redundancy, a BGP cluster may contain two or more route reflectors. Assign a cluster ID with the bgp cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster.
PAGE 350
If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as. If the neighbor is an eBGP neighbor, then BGP performs a check on the first AS number. In this scenario, it is mandatory that the first sequence in the AS path is of type AS_SEQUENCE or AS_CONFED_SEQUENCE (in the case of confederations).
PAGE 351
• bgp four-octet-as-support — enable 4-byte support for the BGP process. bgp connection-retry-timer Configures the BGP connection retry timer. Syntax bgp connection-retry-timer retry-timer-value To return to the default configuration, enter the no connection-retry-timer retry-timer-value command. Parameters retry-timer-value Enter a value that denotes the time interval after which the session retries the connection. The valid range is from 10 to 65535. Defaults 60 seconds.
PAGE 352
• Command History ROUTER BGP-address-family This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.
PAGE 353
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information All routers apply the bgp default local-preference command setting within the AS.
PAGE 354
bgp enforce-first-as Disable (or enable) enforce-first-as check for updates received from EBGP peers. Syntax bgp enforce-first-as To turn off the default, use the no bgp enforce-first-as command. Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 355
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 356
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Routers supporting 4-byte ASNs advertise that function in the OPEN message. The behavior of a 4-byte router is slightly different depending on whether it is speaking to a 2-byte router or a 4-byte router. When creating Confederations, all the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them.
PAGE 357
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information This feature is advertised to BGP neighbors through a capability advertisement. In Receiver Only mode, BGP saves the advertised routes of peers that support this capability when they restart. BGP graceful restart is active only when the neighbor becomes established. Otherwise it is disabled. Gracefulrestart applies to all neighbors with established adjacency.
PAGE 358
bgp outbound-optimization Enables outbound optimization for IBGP peer-group members. Syntax bgp outbound-optimization To disable outbound optimization, enter the no bgp outbound-optimization command. Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command.
PAGE 359
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. Usage Information This command is a knob to disable BGP next-hop resolution using BGP learned routes. During the next-hop resolution, only the first route that the next-hop resolves through is verified for the route’s protocol source and is checked if the route is learned from BGP or not.
PAGE 360
To re-enable optimization engine, use the no bgp regex-eval-optz-disable command. Defaults Enabled Command Modes ROUTER BGP (conf-router_bgp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 361
Related Commands • show ip protocols — view information on all routing protocols enabled and active on the E-Series. bgp router-id Assign a user-given ID to a BGP router. Syntax bgp router-id ip-address To delete a user-assigned IP address, use the no bgp router-id command. Parameters ip-address Enter an IP address in dotted decimal format to reset only that BGP neighbor.
PAGE 362
NOTE: Use this attribute to clear a BGP instance corresponding to either a specific address family in a default VRF or an IPv4 address family in a a nondefault VRF. * Enter an asterisk ( * ) to reset all BGP sessions. <1-4294967295> Enter <1-4294967295> to clear peers with the AS number. <0.1-65535.65535 Enter <0.1-65535.65535> to clear peers with the AS number in dot format. > A.B.C.D Enter the BGP neighbor address in the A.B.C.D format to clear.
PAGE 363
Related Commands Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 6.5.1.0 Expanded to include the as-number option. • bgp recursive-bgp-next-hop — disable next-hop resolution through other routes learned by the BGP. clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state.
PAGE 364
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information After you enter this command, the software deletes the history routes and returns the suppressed routes to the Active state. The clear ip bgp dampening command does not clear the history paths. clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap.
PAGE 365
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 366
soft (OPTIONAL) Enter the keyword soft to reset soft configuration. in Enter the keyword in to re-configure soft inbound updates. out Enter the keyword out to re-configure soft outbound updates. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148.
PAGE 367
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series and Z9500. • permit bandwidth – specify link band width extended-community attribute as the matching criteria to permitting incoming or outgoing traffic. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. Syntax debug ip bgp [ vrf vrf-name | A.B.C.
PAGE 368
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.4.(0.0) Added support for VRF. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 369
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 370
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 371
Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command.
PAGE 372
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group-name] softreconfiguration To disable, use the debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 373
Usage Information This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors. debug ip bgp updates Allows you to view information about BGP updates. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] updates [in | out | prefix-list prefix-list-name] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 374
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. default-metric Allows you to change the metric of redistributed routes to locally originated routes. Use this command with the redistribute command. Syntax default-metric number To return to the default setting, use the no default-metric command. Parameters number Enter a number as the metric to be assigned to routes from other protocols. The range is from 1 to 4294967295.
PAGE 375
Parameters description Enter a description to identify the BGP protocol (80 characters maximum). Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 376
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Support from 2 to 64 paths on the S4810.
PAGE 377
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information By default, when you create a neighbor/peer group configuration in the Router BGP context, this enables IPv4/ Unicast AFI/SAFI.
PAGE 378
both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported. The range is from 2 to 64. Defaults none Command Modes CONFIGURATION-ROUTER-BGP-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 379
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 380
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peer-group-name} allowasin command.
PAGE 381
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ip-address | peer-group-name} default-originate [route-map map-name] To remove a default route, use the no neighbor {ip-address | peer-group-name} defaultoriginate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the default route of all routers in that peer group.
PAGE 382
In order that settings corresponding to the neighbor default-originate command take effect, you must execute the clear ip bgp command immediately after you execute the neighbor default-originate command. neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). Syntax neighbor {ip-address | peer-group-name} description text To delete a description, use the no neighbor {ip-address | peer-group-name} description command.
PAGE 383
peer-group-name Enter the name of the peer group to apply the distribute list filter to all routers in the peer group. prefix-list-name Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes). in Enter the keyword in to distribute only inbound traffic. out Enter the keyword out to distribute only outbound traffic. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 384
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 385
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information When you enable failover, BGP keeps track of IP or IPv6 ability to reach the peer remote address and the peer local address.
PAGE 386
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as. This command automatically restarts the neighbor session for the configuration to take effect.
PAGE 387
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 388
neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors. Syntax neighbor {ip-address | peer-group-name} password [encryption-type] password To delete a password, use the no neighbor {ip-address | peer-group-name} password command. Parameters ip-address Enter the IP address of the router to be included in the peer group. peer-group-name Enter the name of a configured peer group.
PAGE 389
If you configure a password on one neighbor, but you have not configured a password for the neighboring router, the following message appears on the console while the routers attempt to establish a BGP session between them: %RPM0-P:RP1 %KERN-6-INT: No BGP MD5 from [peer's IP address] :179 to [local router's IP address]:65524 Also, if you configure different passwords on the two routers, the following message appears on the console: %RPM0-P:RP1 %KERN-6-INT: BGP MD5 password mismatch from [peer's IP address]
PAGE 390
Usage Information You can assign up to 256 peers to one peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
PAGE 391
Version Description 7.7.1.0 Introduced on the C-Series. Usage Information When you create a peer group, it is disabled (Shut mode). Related Commands • • • neighbor peer-group (assigning peers) — assign routers to a peer group. neighbor remote-as — assign a indirectly connected AS to a neighbor or peer group. neighbor shutdown — disable a peer or peer group.
PAGE 392
Related Commands • • neighbor soft-reconfiguration inbound — assign a subnet to a dynamically configured BGP neighbor. neighbor remote-as — assign an indirectly connected AS to a neighbor or peer group. neighbor remote-as Create and specify the remote peer to the BGP neighbor. Syntax neighbor {ip-address | peer-group-name} remote-as number To delete a remote AS entry, use the no neighbor {ip-address | peer-group-name} remote-as number command.
PAGE 393
neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Syntax neighbor {ip-address | peer-group-name} remove-private-as To return to the default, use the no neighbor {ip-address | peer-group-name} removeprivate-as command. Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers. peer-group-name Enter the name of the peer group to remove the private AS numbers. Defaults Disabled (that is, private AS number are not removed).
PAGE 394
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. map-name Enter the name of an established route map. If the Route map is not configured, the default is deny (to drop all routes). in Enter the keyword in to filter inbound routes. out Enter the keyword out to filter outbound routes.
PAGE 395
peer-group-name Enter the name of the peer group. All routers in the peer group receive routes from a route reflector. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 396
Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to send a COMMUNITY attribute to all routers within the peer group. extended (OPTIONAL) Enter the keyword extended to send extended community attribute. standard (OPTIONAL) Enter the keyword standard to send standard community attribute. Defaults Not configured and COMMUNITY attributes are not sent to neighbors.
PAGE 397
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.
PAGE 398
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group.
PAGE 399
Version Description 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings.
PAGE 400
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Timer values configured with the neighbor timers command override the timer values configured with any other command.
PAGE 401
Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group. interface Enter the keyword loopback then a number of the Loopback interface. The range is from 0 to 16383. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 402
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 403
• • set origin set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 404
mask Enter the mask of the IP address in the slash prefix length format (for example, /24). The mask appears in command outputs in dotted decimal format (A.B.C.D). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 405
Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. • deny bandwidth – link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. redistribute Redistribute routes into BGP.
PAGE 406
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced the ability to substitute IGP cost for MED when a peer/peer-group outbound route-map is set as internal. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes.
PAGE 407
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 408
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information At least one interface must be in Layer 3 mode for the router bgp command to be accepted.
PAGE 409
Usage Information You can use this command to disable all the configured BGP neighbors corresponding to the multicast IPv4 address families. This command is global for all VRFs. shutdown address-family-ipv4–unicast Disables all the BGP neighbors corresponding to the unicast IPv4 address families. Syntax shutdown address-family-ipv4–unicast Use the no shutdown address-family-ipv4–unicast command to enable all the configured BGP neighbors corresponding to the unicast IPv4 address families.
PAGE 410
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 411
Example Version Description 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced. DellEMC(conf-router_bgp)# show capture bgp-pdu neighbor 20.20.20.2 Incoming packet capture enabled for BGP neighbor 20.20.20.
PAGE 412
Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. DellEMC(conf-router_bgp)# show config ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown DellEMC(conf-router_bgp)# show ip bgp View the current BGP IPv4 routing table for the system.
PAGE 413
filter-list as-path- (OPTIONAL) Enter the keyword filter-list then the as-path-name to display the name routes conforming to the filter–list. flap–statistics (OPTIONAL) Enter the keyword flap-statistics to display flap statistics of the routes. neighbors (OPTIONAL) Enter the keyword neighbors to display the detailed information on TCP and BGP neighbor connections.
PAGE 414
Version Description 7.7.1.0 Introduced on the C-Series. Usage Information When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. In BGP, this command displays the exact reason why the route is discarded. The following describes the show ip bgp command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route.
PAGE 415
ID *>I ID *>I ID *>I ID ID ID ID ID 110.1.1.0/24 111.1.1.0/24 112.1.1.0/24 113.1.1.0/24 114.1.1.0/24 115.1.1.0/24 116.1.1.0/24 117.1.1.0/24 118.1.1.0/24 119.1.1.0/24 120.1.1.0/24 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.2 11.1.1.
PAGE 416
show ip bgp cluster-list View BGP neighbors in a specific cluster. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] clusterlist [cluster-id] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view cluster information of BGP neighbors corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
PAGE 417
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. DellEMC# show ip bgp cluster-list BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 418
All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to view all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. Command Modes • • Command History This guide is platform-specific.
PAGE 419
Example DellEMC# show ip bgp community ? local-AS Do not export outside local AS (well-known community) no-advertise Do not advertise to any peer (well-known community) no-export Do not export to next AS (well-known community) aa:nn Community number in aa:nn format | Pipe through a command DellEMC# show ip bgp community BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 420
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 421
show ip bgp dampened-paths View BGP routes that are dampened (non-active). Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
PAGE 422
Field Description From Displays the IP address of the neighbor advertising the dampened route. Reuse Displays the hour:minutes:seconds until the dampened route is available. Path Lists all the ASs the dampened route passed through to reach the destination network. Example DellEMC# show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 423
Example DellEMC# show ip bgp detail Detail information for BGP Node bgpNdP 0x41a17000 : NdTmrP 0x41a17000 : NdKATmrP 0x41a17014 : NdTics 74857 : NhLocAS 1 : NdState 2 : NdRPMPrim 1 : NdListSoc 13 NdAuto 1 : NdEqCost 1 : NdSync 0 : NdDefOrg 0 NdV6ListSoc 14 NdDefDid 0 : NdConfedId 0 : NdMedConfed 0 : NdMedMissVal -1 : NdIgnrIllId 0 : NdRRC2C 1 : NdClstId 33686273 : NdPaTblP 0x41a19088 NdASPTblP 0x41a19090 : NdCommTblP 0x41a19098 : NhOptTransTblP 0x41a190a0 : NdRRClsTblP 0x41a190a8 NdPktPA 0 : NdLocCBP 0x41a
PAGE 424
ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. list name Enter the extended community list name you wish to view. The range is 140 characters. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.
PAGE 425
show ip bgp filter-list View the routes that match the filter lists. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] filterlist as-path-name vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes.
PAGE 426
Field Description • Example r = redistributed route entry Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 427
• • • • • • ? = (question mark) sequences in a pattern (either zero or one sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. [ ] = (brackets) a range of single-character patterns. ( ) = (parenthesis) groups a series of pattern elements to a single element. { } = (braces) minimum and the maximum match count. ^ = (caret) the beginning of the input string.
PAGE 428
n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network h 77.0.0.0/24 d 55.0.0.0/24 *> 66.0.0.0/24 *>n 66.66.77.77/32 DellEMC# From 172.16.0.2 172.16.0.2 172.16.0.2 0.0.0.
PAGE 429
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. DellEMC# show ip bgp inconsistent-as BGP table version is 280852, local router ID is 10.1.2.
PAGE 430
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
PAGE 431
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Added the detail option. Output now displays the default MED value. 7.2.1.0 Added the received and denied route options. 6.3.10 The output is changed to display the total number of advertised prefixes. Usage Information After a peer reset, the contents of the notification log messages is displayed in hex values for debugging.
PAGE 432
The Lines Beginning with: Description Prefix advertised Displays the number of network prefixes advertised, the number rejected, and the number withdrawn from the BGP routing table. Connections established Displays the number of TCP connections established and dropped between the two peers to exchange BGP information. Last reset Displays the amount of time since the peering session was last reset. Also states if the peer resets the peering session.
PAGE 433
show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. Syntax show ip bgp [vrf vrf-name] next-hop Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.
PAGE 434
show ip bgp paths View all the BGP path attributes in the BGP database. Syntax show ip bgp[vrf vrf-name] paths [regexp regular-expression] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf to view all path attributes in the BGP database corresponding to that VRF. NOTE: DescriptionYou can use this attribute to view information on all path attributes in the BGP database that correspond to either a default or a nondefault VRF.
PAGE 435
Usage Information The following describes the show ip bgp path command shown in the following example. Field Description Total Displays the total number of BGP path attributes. Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using this path attribute. Metric Displays the MED attribute for this path attribute.
PAGE 436
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The following describes the show ip bgp paths community command shown in the following example. Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored.
PAGE 437
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. Introduced on S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T.
PAGE 438
Related Commands • • neighbor peer-group (assigning peers) — assign a peer to a peer-group. neighbor peer-group (creating group) — create a peer group. show ip bgp regexp Display the subset of the BGP routing tables matching the regular expressions specified. Syntax show ip bgp [vrf vrf-name] regexp regular-expression [character] Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to view the subset of BGP routing tables that match the regular expression specified on that VRF.
PAGE 439
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information The following describes the show ip bgp regexp command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then non-BGP routes exist in the router’s routing table.
PAGE 440
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 441
Field Description MsgRcvd Displays the number of BGP messages that neighbor received. MsgSent Displays the number of BGP messages that neighbor sent. TblVer Displays the version of the BGP table that was sent to that neighbor. InQ Displays the number of messages from that neighbor waiting to be processed. OutQ Displays the number of messages waiting to be sent to that neighbor. If a number appears in parentheses, the number represents the number of messages waiting to be sent to the peer group.
PAGE 442
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 443
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series.
PAGE 444
Dell EMC Platform Support Networking OS Version 7.8.1.0, MBGP for IPv4 Multicast Only S-Series debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 445
distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command. Parameters external-distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internal-distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200.
PAGE 446
ipv4 unicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.
PAGE 447
Origin codes: i - IGP, e - EGP, ? - incomplete Network d From 55.0.0.0/24 172.16.0.2 Reuse Path 00:36:23 200 DellEMC# BGP Extended Communities (RFC 4360) BGP Extended Communities, as defined in RFC 4360, is an optional transitive BGP attribute. BGP Extended Communities provides two major advantages over Standard Communities: • • The range is extended from 4-octet (AA:NN) to 8-octet (Type:Value) to provide enough number communities.
PAGE 448
Version Description 7.6.1.0 Introduced on the E-Series. Usage Information If the set community rt and soo are in the same route-map entry, the behavior defines as: • Related Commands • • If the rt option comes before soo, with or without the additive option, soo overrides the communities rt sets. If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. If the rt with the additive option comes after soo, rt adds the communities soo sets.
PAGE 449
Related Commands • • If the rt option comes after soo, without the additive option, rt overrides the communities soo sets. If the rt with the additive option comes after soo, rt adds the communities soo sets. • set extcommunity rt — set the extended community route origins using the route-map. show ip bgp paths extcommunity To display all BGP paths having extended community attributes, use this feature.
PAGE 450
Parameters word Enter the name of the extended community list you want to view. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.
PAGE 451
NOTE: If you enter soft, without an in or out option, both inbound and outbound policies are reset. out Reapply only outbound policies. NOTE: If you enter soft, without an in or out option, both inbound and outbound policies are reset. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 452
Version Description 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced on the E-Series. Usage Information This command turns on BGP soft-reconfiguration inbound debugging for IPv6 unicast routes. If no neighbor is specified, debug is turned on for all neighbors. ipv6 prefix-list Configure an IPv6 prefix list. Syntax ipv6 prefix-list prefix-list name Parameters prefix-list name Enter the name of the prefix list. NOTE: There is a 140-character limit for prefix list names.
PAGE 453
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 8.4.1.0 Added support for IPv4 multicast and IPv4 unicast address families. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information This command enables soft-reconfiguration for the specified BGP neighbor. BGP stores all updates for inbound IPv6 unicast routes the neighbor receives but does not reset the peer-session.
PAGE 454
Parameters ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. summary Display a summary of RPF routes. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 454 Version Description 9.10(0.
PAGE 455
10 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. NOTE: If you are using these features for the first time, contact Dell EMC Networking Technical Assistance Center (TAC) for guidance.
PAGE 456
• • • • • • • • • • • • • • • IPV4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 nlbclusteracl: 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 ipv4udfmirracl: 0 vrfv4Acl :0 Openflow : 0 fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range is from 0 to 8.
PAGE 457
fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The range is from 0 to 6. Iscsioptacl Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2. number ipv4udfmirracl Enter the keyword ipv4udfmirracl and then the number of FP blocks for IPv4 UDF mirror ACL. The range is from 0 to 8. ipv4mirracl Enter the ipv4mirracl keyword and then the number of FP blocks for IPv4 mirror ACL. The range is from 0 to 8.
PAGE 458
The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only number of blocks can be configured by the user . If allocation values are not entered for the CAM regions, the value is 0. If you enable BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the command reload conditional nvram-cfg-change. cam-acl-egress Allocate CAM for egress ACLs.
PAGE 459
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 460
Command History Version Description 9.14.1.0 Introduced on the S4810 and S4820T. 9.13.0.0 Introduced on the MXL, FN IOM, S5000, S4048-ON, S6000, S6000-ON, S3048-ON, S3100 Series, C9010, S4048T-ON, Z9500, Z9100-ON, S6100-ON, S6010-ON. Usage Information The no cam-threshold command will set the CAM threshold to 90 percent and silence period to 0. The CAM threshold and silence period configuration is applicable only for Ingress L2, IPv4, IPv6 and Egress L2, IPv4, and IPv6 ACL CAM groups.
PAGE 461
Example DellEMC# show cam-acl -- Chassis Cam ACL -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 256 entries L2Acl : 2 Ipv4Acl : 4 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4p
PAGE 462
IPV6(IPV4QOS) Triple Wide Regions: VmanQos, Openflow, ipv4udfmirracl L2Acl : 2 Ipv4Acl : 4 Ipv6Acl* : 2 Ipv4Qos* : 0 L2Qos : 2 L2PT : 0 IpMacAcl : 1 VmanQos : 0 EcfmAcl : 0 EtsAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl : 0 ipv4udfmirracl: 0 ipv4mirracl : 0 * - shared regions show cam-usage Display the amount of memory space used and available in each CAM partition (including Layer 2 ACL, Layer 3 ACL, and IPv4Flow) Syntax show cam-usage [acl | rout
PAGE 463
Example Field Description CAM-Region Type of area in the CAM block that is used for ACL VLAN groups Total CAM space Total amount of space in the CAM block Used CAM Amount of CAM space that is currently in use Available CAM Amount of CAM space that is free and remaining to be allocated for ACLs DellEMC#show cam-usage Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM =========|========|====================|===========|==========|============== 0 | 0 | IN-L2 ACL | 1024 | 0 | 10
PAGE 464
number Enter all to get information for all the stack-units or enter the stack-unit number to get information for a specific stack-unit. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 465
Example Unified Forwarding Table Modes Unified Forwarding Table (UFT) consolidates the resources of several search tables (Layer 2, Layer 3 Hosts, and Layer 3 Route [Longest Prefix Match — LPM]) into a single flexible resource. The system supports several UFT modes to extract the forwarding tables, as required. By default, Dell EMC Networking OS initializes the table sizes to UFT mode 2 profile, as it provides a reasonable shared memory for all the tables.
PAGE 466
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch.
PAGE 467
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 468
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax service-policy rate-limit-cpu-queues policy-name Parameters policy-name Enter the service-policy name, using a string up to 32 characters. Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 469
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 470
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Usage Information Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv6 unknown-unicast Disable soft forwarding of unknown IPv6 destination packets.
PAGE 471
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 472
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 473
Example Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 474
DellEMC# 474 09:00:2b:00:00:04/05 any Control Plane Policing (CoPP) Q9 CP
PAGE 475
12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell EMC Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 476
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 477
Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Usage Information If you do not use the statistics parameter, both hardware and DCBx counters clear. description Enter a text description of the DCB policy (PFC input or ETS output).
PAGE 478
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Usage Information NOTE: Please note that Dell Networking does not recommended to use this command as it has been deprecated in the current 9.4.(0.0) release. A warning message appears when you try to run this command indicating that you have to use the dcb-map commands in the future.
PAGE 479
• dot1p Value in the Incoming Frame Description heading 0 1 1 0 2 2 3 3 4 4 5 5 6 6 7 7 Before configuring the port queues to function as no-drop queues, you must first apply the dcb-map map with pfc mode off. To apply the dcb-map with pfc mode off, use the following commands: dcb-map pfcoff and no pfc mode on. show dcb Displays the data center bridging status, the number of PFC-enabled ports, and the number of PFC-enabled queues.
PAGE 480
show interface pfc Displays the PFC configuration applied to ingress traffic on an interface, including priorities and link delay. Syntax show interface port-type slot/port[/subport] pfc {summary | statistics | detail | buffer-threshold} Parameters port-type slot/ Enter the port-type slot and port PFC information. Enter the subport number if a port is port[/subport] pfc fanned-out into 10G ports.
PAGE 481
Field Description Remote is Operational status (enabled or disabled) of peer device for DCBX exchange of PFC enabled, Priority configuration with a list of the configured PFC priorities. Willing status of peer device for list Remote Willing DCBX exchange (Willing bit received in PFC TLV): enabled or disable. Status is enabled Local is enabled DCBX operational status (enabled or disabled) with a list of the configured PFC priorities.
PAGE 482
Example (Summary) Field Description PFC TLV Statistics: Pause Rx pkts Number of PFC pause frames received.
PAGE 483
• For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/ [subport]. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 1/1/4. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 484
Example (Summary) Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 485
Usage Information By default, equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure bandwidth amounts in associated dot1p queues, use the bandwidth-percentage command. When specified bandwidth is assigned to some port queues and not to others, the remaining bandwidth (100% minus assigned bandwidth amount) is equally distributed to unassigned non-strict priority queues in the priority group.
PAGE 486
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 487
priority-list Configure the 802.1p priorities for the traffic on which you want to apply an ETS output policy. Syntax priority-list value To remove the priority list, use the no priority-list command. Parameters value Enter the priority list value. Separate priority values with a comma; specify a priority range with a dash; for example, priority-list 3,5-7. The range is from 0 to 7. Defaults None Command Modes PRIORITY-GROUP Command History This guide is platform-specific.
PAGE 488
If an error occurs when a port receives a peer’s ETS configuration, the port’s configuration is reset to the previously configured ETS output policy. If no ETS output policy was previously applied, the port is reset to the default ETS parameters. You can only associate output QoS policy profiles with the priority groups in the DCB output profile context; output QoS policy profiles are not permitted on output policy-maps.
PAGE 489
Parameters port-type slot/ Enter the port-type slot and port ETS information. Enter the subport number if a port is port[/subport] ets fanned-out into 10G ports. {summary | detail} Enter the keyword summary for a summary list of results or enter the keyword detail for a full list of results. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 490
------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts Del
PAGE 491
Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Error Reco TLV Pkts DellEMC# show interfaces tengigabitethernet 1/1 ets detail Interface TenGigabitEthernet 1/1 Max Supported TC Groups is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled TC-grp Priority# Bandwidth TSA 0 0,1,2,3,4,5,6,7 100% ETS 1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0%
PAGE 492
-----------------Admin is enabled TC-grp Priority# 0 0,1,2,3,4,5,6,7 1 2 3 4 5 6 7 Priority# 0 1 2 3 4 5 6 7 Remote Parameters: ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# 0 0,1,2,3,4,5,6,7 1 2 3 4 5 6 7 Bandwidth 100% 0% 0% 0% 0% 0% 0% 0% TSA ETS ETS ETS ETS ETS ETS ETS ETS Bandwidth 13% 13% 13% 13% 12% 12% 12% 12% TSA ETS ETS ETS ETS ETS ETS ETS ETS Bandwidth 100% 0% 0% 0% 0% 0% 0% 0% TSA ETS ETS ETS ETS ETS ETS ETS ETS Priority# Bandwi
PAGE 493
Example (Summary) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048–ON and S4048–ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 494
Max Supported TC Groups is 4 Number of Traffic Classes is 1 Admin mode is on Admin Parameters: -------------------Admin is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 - DCBX Commands The following DCBX commands are supported on the Dell EMC Networking OS. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements.
PAGE 495
• iscsi: enables the advertisement of iSCSI in application priority TLVs. Defaults Application priority TLVs are enabled to advertise FCoE and iSCSI. Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.
PAGE 496
Usage Information You can configure the transmission of more than one TLV type at a time; for example: advertise dcbx-tlv ets-conf ets-reco. You can enable ETS recommend TLVs (ets-reco) only if you enable ETS configuration TLVs (ets-conf). To disable TLV transmission, use the no form of the command; for example, no advertise dcbx-tlv pfc ets-reco. DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch.
PAGE 497
dcbx version Configure the DCBX version used on the interface. Syntax dcbx version {auto | cee | cin | ieee-v2.5} To remove the DCBX version, use the dcbx version {auto | cee | cin | ieee-v2.5} command. Parameters auto | cee | cin | ieee-v2.5 Enter the DCBX version type used on the interface, where: • • • • auto: configures the port to operate using the DCBX version received from a peer. cee: configures the port to use CDD (Intel 1.01). cin: configures the port to use Cisco-Intel-Nuova (DCBX 1.0).
PAGE 498
• • sem: enables traces for the DCBX state machine. tlv: enables traces for DCBX TLVs. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON.
PAGE 499
iscsi priority-bits Configure the iSCSI priority advertised for the iSCSI protocol in application priority TLVs. Syntax iscsi priority-bits priority-bitmap To remove the configured iSCSI priority, use the no iscsi priority-bits command. Parameters priority-bitmap Enter the priority-bitmap range. The range is from 1 to FF. Defaults 0x10 Command Modes PROTOCOL LLDP Command History This guide is platform-specific.
PAGE 500
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Down status messages added. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Usage Information To clear DCBX frame counters, use the clear dcbx counters interface stack-unit/port command.
PAGE 501
Field Description Peer DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs received from the peer device. Peer DCBX Highest DCBX version supported in Control TLVs received from the peer device. Status: DCBX Max Version Supported Peer DCBX Status: Sequence Number Sequence number transmitted in Control TLVs received from the peer device. Peer DCBX Status: Acknowledgment Number Acknowledgement number transmitted in Control TLVs received from the peer device.
PAGE 502
DCBX Max Version Supported is 255 Sequence Number: 2 Acknowledgment Number: 2 Total DCBX Frames transmitted 27 Total DCBX Frames received 6 Total DCBX Frame errors 0 Total DCBX Frames unrecognized 0 dcb-map Create a DCB map to configure priority flow control (PFC) and enhanced transmission selection (ETS) on Ethernet ports that support converged Ethernet traffic. Apply the DCB map to an Ethernet interface. Syntax dcb-map map-nameTo remove a DCB map from an ethernet interface, use the no dcb-map command.
PAGE 503
Parameters dot1p0–7_groupnum Enter the priority group number for each 802.1p class of traffic in a DCB map. Defaults None Command Modes DCB MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 504
To disable PFC operation on an interface, enter the no pfc mode on command in DCB Input Policy Configuration mode. PFC is enabled and disabled as global DCB operation is enabled (dcb-enable) or disabled (no dcb-enable). You cannot enable PFC and link-level flow control at the same time on an interface. NOTE: We do not recommended to use this command as it has been deprecated in the current 9.4(0.0) release.
PAGE 505
If a priority group does not use its allocated bandwidth, the unused bandwidth is made available to other priority groups. To remove a priority-group configuration in a DCB map, enter the no priority-group bandwidth pfc command. By default, equal bandwidth is assigned to each dot1p priority in a priority group. Use the bandwidth parameter to configure the bandwidth percentage assigned to a priority group.
PAGE 506
Version Description 9.3(0.0) Introduced on the S4810 and S6000 platforms. 9.3(0.0) Introduced on the FC Flex IO module installed in the MXL 10/40GbE Switch. Usage Information Use the show qos dcb-map command to display the enhanced transmission selection (ETS) and priority-based flow control (PFC) parameters used to configure server-facing Ethernet ports. S5000 Ethernet ports are DCBxenabled by default. The following table describes the show qos dcb-map output shown in the example below.
PAGE 507
Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.6(0.0) Introduced on the S5000. 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms. Usage Information Configure the maximum shared buffer available for PFC traffic. You can choose to increase or decrease the shared buffer that is allocated in the system by default. Configure the shared buffer size less than the total PFC buffer size.
PAGE 508
priority value buffer-size size pause-threshold threshold-value peak-headroom headroom-value resume-offset threshold-value shared-threshold-weight size DellEMC(conf-dcb-buffer)#priority value buffer-size size pause-threshold threshold-value peak-headroom headroom-value resume-offset threshold-value shared-threshold-weight size priority Configure the priority for the PFC threshold to be allocated to the buffer space parameters.
PAGE 509
PFC detects congestion on a queue for a specified priority, it sends a pause frame for the 802.1p priority traffic to the transmitting device. You can use the priority command to set up both the administrative and peer-related PFC priorities. For example, you can configure the intended buffer configuration for all eight priorities.
PAGE 510
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.3(0.0) Introduced on the S4810, S4820T, S6000, and MXL platforms. Usage Information You must apply this buffer policy at the interface level for the attributes to be applicable in conjunction with the DCB input policy.
PAGE 511
Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process. For example, you can assign a higher priority for time-sensitive applications and a lower priority for other services, such as file transfers.
PAGE 512
Parameters Command Modes name Enter the name of the profile, which can be a string of up to 32 characters in length.
PAGE 513
Usage Information Configure the maximum buffer available for PFC traffic. You can choose to increase or decrease the buffer size that is allocated in the system by default. However, if you modify the PFC buffer size lower than the previously configured size, the system determines whether this reduction in size is valid without disrupting the existing configuration. In such a scenario, disable and re-enable DCB. The lossless queue limit per port is validated based on the dcb pfc-queues command.
PAGE 514
Field Description Field Description Profile name Name of the DCB buffer threshold profile Priority The priority of the queue for which the buffer space settings apply buffer-size Ingress buffer size pause-thresholdvalue Buffer limit at which the port sends the pause to peer in KB. resume-threshold- Buffer offset limit at which the port resumes the peer in KB.
PAGE 515
service-class buffer shared-threshold-weight Create a service class and associate the threshold weight of the shared buffer with each of the queues per port in the egress direction.
PAGE 516
Example DellEMC(conf-if-te-1/8)# Service-class buffer shared-threshold-weight queue5 4 queue7 6 dcb pfc-queues Configure the number of PFC queues. Syntax dcb pfc-queues value Parameters value Enter the number of PFC queues in the range of 0 through 4. The number of ports supported based on lossless queues configured will depend on the buffer. Default The default number of PFC queues in the system is 2 for S4810 and 1 for S6000 platforms.
PAGE 517
Version Description 9.3 (0.1) Introduced on S6000, S4810, and S4820T. Usage Information PFC and ETS are enabled by default on the interfaces when DCB is globally enabled (refer to dcb enable). In some network topology, you may want to disable PFC on an interface and apply link level flow control; Similarly you may want to disable ETS on an interface and apply QoS bandwidth configurations. Limitations • • “dcb-map” CLI on interface is mutually exclusive to “no dcb ets enable” and “no dcb pfc enable”.
PAGE 518
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell EMC Networking OS. Topics: • • • Diagnostics and Monitoring Commands Offline Diagnostic Commands Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 519
application coredump is aborted. Dell EMC Networking OS completes the coredump process and wait until the upload is complete before rebooting the system. Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell EMC Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby.
PAGE 520
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 521
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. Usage Information You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented.
PAGE 522
Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 523
clear hardware system-flow Clear system-flow statistics from selected hardware components. Syntax Parameters clear hardware system-flow layer2 stack-unit number port-set 0–0 counters stack-unit number Enter the keywords stack-unit then a number to select a particular stack member and then enter one of the following command options to clear a specific collection of data.
PAGE 524
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command. hardware watchdog To trigger a reboot and restart the system, set the watchdog timer. Syntax hardware watchdog stack-unit {stack-unit-number | all} Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 525
port-set 0–0 Enter the keywords port-set with a port-pipe number to display the MAC ACL entries for the specified port-pipe number. . The range is from 0 to 0. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 526
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. show hardware stack-unit Display the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 527
• Command History Example (DataPlane) Example (PartyBus) EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Increased the stacking range to 12 units in S3100 series. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 528
Example (Drops Unit) Example (PortStats) Example (Register) 528 DellEMC# sh hard stack-unit 1 drops unit 0 PortNumber Ingress Drops IngMac Drops Total Mmu Drops 1 0 0 0 2 0 0 0 3 0 0 0 4 0 0 0 EgMac Drops Egress Drops 0 0 0 0 0 0 0 0 DellEMC# DellEMC# show hardware stack-unit 1 unit 0 port-stats ena/ speed/ link auto STP lrn inter max loop port link duplex scan neg? state pause discrd ops face frame back ge0 down SW Yes Block Untag FA SGMII 1554 ge1 !ena SW Yes Block Tag FA SGMII 1554 ge2 !ena SW Yes Bl
PAGE 529
0x0061c04c ASFPORTSPEED.cpu0 = 0x00000000 0x00780000 AUX_ARB_CONTROL.ipipe0 = 0x0000001c 0x0e700102 BCAST_BLOCK_MASK.ge0 = 0x00000000 0x0e701102 BCAST_BLOCK_MASK.ge1 = 0x00000000 0x0e702102 BCAST_BLOCK_MASK.ge2 = 0x00000000 0x0e703102 BCAST_BLOCK_MASK.ge3 = 0x00000000 0x0e704102 BCAST_BLOCK_MASK.ge4 = 0x00000000 0x0e705102 BCAST_BLOCK_MASK.ge5 = 0x00000000 0x0e706102 BCAST_BLOCK_MASK.ge6 = 0x00000000 0x0e707102 BCAST_BLOCK_MASK.ge7 = 0x00000000 0x0e708102 BCAST_BLOCK_MASK.
PAGE 530
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 530 13 - Pause Control Frame Counter Oversized Frame Counter Jabber Frame Counter VLAN Tag Frame Counter Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter VLAN Tagged Packets Ingress Dropped Packet MTU Check Error Frame Counter PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame
PAGE 531
--------------------unit: 0 port: 61 (interface Fo 1/60) Description RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - IPV4 L3 Unicast Frame Counter IPV4 L3 Routed Multicast Packets IPV6 L3 Unicast Frame Counter IPV6 L3 Routed Multicast Packets Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte F
PAGE 532
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX Example (Details) - Byte Counter Control Frame Counter Pause Control Frame Counter Oversized Frame Counter Jabber Counter VLAN Tag Frame Counter Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame Priority 2 PFC Frame Priority 3 PFC Frame Priority 4 PFC Frame Priority 5 PFC Frame Priority 6 PFC Frame Priority 7 Debug Counter 0 Debug Counter 1 Debug Counte
PAGE 533
The linkStatus of Front End Port 15 is FALSE The linkStatus of Front End Port 16 is FALSE The linkStatus of Front End Port 17 is FALSE The linkStatus of Front End Port 18 is FALSE The linkStatus of Front End Port 19 is FALSE The linkStatus of Front End Port 20 is FALSE The linkStatus of Front End Port 21 is FALSE The linkStatus of Front End Port 22 is FALSE The linkStatus of Front End Port 23 is TRUE The linkStatus of Hg Port 24 is TRUE The linkStatus of Hg Port 25 is TRUE The linkStatus of Hg Port 26 is FA
PAGE 534
port-set number [counters] Enter the keywords port-set with a port-pipe number. (OPTIONAL) Enter the keyword counters for the specified port-pipe. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example 534 Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 535
Example param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=1, mode=0x01, entries=1} ############## FP Entry for redirecting LACP traffic to CPU Port ############ EID 2045: gid=1, slice=15, slice_idx=0x02, prio=0x7fd, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 0180c200 00020000 00000000 0000
PAGE 536
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command.
PAGE 537
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500.
PAGE 538
• • Command Modes For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.
PAGE 539
Rx VLAN Drops --- Ingress MAC counters--Ingress FCSDrops Ingress MTUExceeds --- MMU Drops --Ingress MMU Drops HOL DROPS(TOTAL) HOL DROPS on COS0 HOL DROPS on COS1 HOL DROPS on COS2 HOL DROPS on COS3 HOL DROPS on COS4 HOL DROPS on COS5 HOL DROPS on COS6 HOL DROPS on COS7 HOL DROPS on COS8 HOL DROPS on COS9 HOL DROPS on COS10 HOL DROPS on COS11 HOL DROPS on COS12 HOL DROPS on COS13 HOL DROPS on COS14 HOL DROPS on COS15 HOL DROPS on COS16 HOL DROPS on COS17 TxPurge CellErr Aged Drops --- Egress MAC counters--E
PAGE 540
• Command Modes Interface all prio-group {id | all} - ingress priority-group level snapshot EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the keyword interface all. 9.7(0.
PAGE 541
Parameters interface interface Enter any of the following keywords and slot/port[/subport] or number information: • • Command Modes For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. priority-group Enter the keyword priority-group followed by id for specific priority-group or keyword all.
PAGE 542
service-pool detail Enter the keyword service-pool followed by the keyword detail to view detailed information about the service pool usage. interface interface Enter any of the following keywords and the interface information: • • Command Modes For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information.
PAGE 543
MCAST MCAST MCAST MCAST Example displaying egress queue-level snapshot for unicast packets for the specific interface 5 6 7 8 0 0 0 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 queue ucast 10 Unit 0 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 10 0 DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 queue ucast all Unit 1 unit: 0 port: 1 (
PAGE 544
DellEMC# show hardware buffer-stats-snapshot resource interface fortyGigE 1/49 priority-group all Unit 1 unit: 0 port: 1 (interface Fo 1/49) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 544 Debugging and Diagnostics
PAGE 545
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 546
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Usage Information Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display Dell OS debugging messages for DHCP. Syntax debug ip dhcp server [events | packets] Parameters events Enter the keyword events to display the DHCP state changes.
PAGE 547
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 548
disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default. To enable the system to be a DHCP server, use the no disable command. Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 549
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 550
excluded-address Prevent the server from leasing an address or range of addresses in the pool. Syntax excluded-address [address | low-address high-address] Parameters address Enter a single address to be excluded from the pool. low-address Enter the lowest address in a range of addresses to be excluded from the pool. high-address Enter the highest address in a range of addresses to be excluded from the pool. Defaults None Command Modes DHCP Command History This guide is platform-specific.
PAGE 551
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 552
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the S4810 and S4820T. 9.0.2.
PAGE 553
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-name-server Specify the NetBIOS Windows Internet Naming Service (WINS) name servers, in order of preference, that are available to Microsoft Dynamic Host Configuration Protocol (DHCP) clients. Syntax Parameters netbios-name-server address [address2...address8] address Enter the address of the NETBIOS name server.
PAGE 554
• • Mixed: Enter the keyword m-node. Peer-to-peer: Enter the keyword p-node. Defaults Hybrid Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 555
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. pool Create an address pool. Syntax Parameters pool name name Enter the address pool’s identifying name. Defaults None Command Modes DHCP Command History This guide is platform-specific.
PAGE 556
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 557
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. DellEMC# show ip dhcp configuration global Protocol status : Enabled Number of ping packets : 1 DellEMC# DellEMC# show ip dhcp configuration Pool Name Pool Type Domain Name Lease Time DNS Servers Default Routers Network : : : : : : : pool p1 p1 Dynamic dell.com 2Days 0Hrs 0Mins 10.11.0.1 1.1.1.1 1.1.1.0 255.255.255.
PAGE 558
show ip dhcp server Display the DHCP server statistics. Syntax show ip dhcp server statistics Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 559
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. • arp inspection-trust — specify a port as trusted so that ARP frames are not validated against the binding table.
PAGE 560
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.
PAGE 561
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added the keywords discard-counters, interface, and the variable interface on the S4810, S4820T, S5000, S6000, Z9000, Z9500. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.
PAGE 562
Example Version Description 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. DellEMC# clear ipv6 dhcp snooping? binding Clear the snooping binding database ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [remote-id {port | hostname:port | mac} | circuit-d {port | hostname:port | mac} | trust-downstream] Parameters remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82.
PAGE 563
Version Description 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 564
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 565
ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected: • • lease time For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Enter the keyword lease then the amount of time the IP address are leased.
PAGE 566
IPv6 DHCP Snooping Binding Create a static DHCP snooping binding entry in the snooping database. Syntax [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease value To delete the DHCP snooping binding entry from DHCP snooping database, use the [no] ipv6 dhcp snooping binding mac address vlan-id vlan-id ipv6 ipv6-address interface interface-type | interface-number lease valuecommand.
PAGE 567
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 568
ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults None Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 569
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 570
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp source-address-validation Enable the IP Source Guard. Syntax [no] ip dhcp source-address-validation [ipmac] [vlan vlan-id] Parameters ipmac Enable IP+MAC Source Address Validation.
PAGE 571
1. Use the cam-acl l2acl command from CONFIGURATION mode. 2. Save the running-config to the startup-config. 3. Reload the system. ip dhcp relay information-option Enable Option 82. Syntax Parameters ip dhcp relay information-option [remote-id {hostname | mac | WORD}] [circuit-d {hostname:port}] [trust-downstream] [vpn] remote-id Enter the keyword remote-id to configure the system to enable the remote-id string in option-82.
PAGE 572
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series. Example DellEMC(conf)# ip dhcp relay information-option vpn ip dhcp relay source-interface Configure IPv4 DHCP relay source interface. Syntax ip dhcp relay source–interface interface To disable the IPv4 DHCP relay source interface, use the no ip dhcp relay source–interface interface command.
PAGE 573
To disable the DHCP relay source IPv6 interface, use the no ipv6 dhcp relay source–interface interface command. Parameters source-interface interface Enter the keyword source-interface then the type of interface and the interface information: • • • • • • • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/plot information. For a 10-Gigabit Ethernet information, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 574
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.2.1.0 Introduced on the C-Series and S-Series. ipv6 dhcp snooping verify mac-address Configure to enable verify source mac-address against ipv6 DHCP packet mac address.
PAGE 575
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 576
Example DellEMC(conf-if-te-1/1)# ipv6 helper-address X:X:X:X::X IPv6 helper address VRF VRF name. show ip dhcp snooping Display the contents of the DHCP binding table or display the interfaces configured with IP Source Guard. Syntax show ip dhcp snooping [binding | source-address-validation [discard-counters [interface interface]]] Parameters Parameters Description binding Display the binding table. source-addressvalidation Display the interfaces configured with IP Source Guard.
PAGE 577
Example Version Description 7.8.1.0 Introduced on the C-Series and S-Series. The following example displays the interfaces configured with IP Source Guard: DellEMC> show ip dhcp snooping source-address-validation ip sav access-list on TenGigabitEthernet 1/1 Total cam count 3 permit host 0.0.0.0 count (0 packets) permit host 10.1.1.252 count (0 packets) permit host 10.1.1.253 count (0 packets) ipmac-vlan sav access-list on TenGigabitEthernet 1/2 Total cam count 4 permit host 0.0.0.
PAGE 578
The following example displays the SAV discard counters on a port channel interface: DellEMC> show ip dhcp snooping source-address-validation discard-counters interface portchannel 10 deny access-list on Port-channel 10 on stack-unit 1 Total cam count 1 deny vlan 10 count (0 packets) deny access-list on Port-channel 10 on stack-unit 2 Total cam count 1 deny vlan 10 count (0 packets) deny access-list on Port-channel 10 on stack-unit 3 Total cam count 1 deny vlan 10 count (0 packets) NOTE: The output for port
PAGE 579
Commands to Configure DNS To configure the Domain Names Systems (DNS) on the system, use the following commands: ip name-server Configures one or more name server (DNS) IP addresses. You can configure up to six IP addresses. Syntax ip name-server [vrf vrf-name] ip-address [ip-address2] [ip-address3] [ipaddress4] [ip-address5] [ip-address6] To undo the name server ip address configuration for VRF, use the no ip name-server [vrf vrf-name] ip-address command.
PAGE 580
To undo the domain name configuration corresponding to a specific VRF, use the no ip domain-name [vrf vrf-name] name command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the domain corresponding to that VRF. name Enter the name of the domain to be appended to the in complete DNS requests corresponding to the specified VRF. Defaults None Command Modes EXEC Command History This guide is platform-specific.
PAGE 581
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Usage Information Use this command to add domain names to the DNS lists corresponding to a specific VRF.
PAGE 582
Example DellEMC(conf)# ip host vrf jay dell 1.1.1.1 clear host Removes one or all dynamically learned host table entries for a specific VRF. Syntax clear host [vrf vrf-name] {* | host-name} Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to delete dynamically learned host table entries corresponding to that VRF. host-name Enter the name of the host corresponding to which you want to delete the dynamically learnt host table entries.
PAGE 583
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • • • • • • • • • • ecmp-group hash-algorithm hash-algorithm ecmp hash-algorithm seed ip ecmp-group ip ecmp weighted link-bundle-monitor enable link-bundle-distribution trigger-threshold show config show link-bundle distribution ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
PAGE 584
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Usage Information Using CONFIGURATION mode, create an ECMP group ID.
PAGE 585
hg {crc16 | crc16cc | Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices: crc32MSB | • crc32LSB | xor1 | xor2 | xor4 | xor8 | • • xor16} • • • • • • lag {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} Enter the keyword hg then one of the following options available in the stack-unit and linecard provisioned devices:: • • • • • • • • • hg-seed seed- value crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomia
PAGE 586
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Added the nh-ecmp option. 7.7.1.1 Added the nh-ecmp option.
PAGE 587
Term heading Description heading dest-ip Uses the destination IP for ECMP hashing. The default is enabled. lsb Returns the LSB of the key as the hash. The default is crc-lower. Defaults • • Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. crc-lower dest-ip enabled Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 588
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. Usage Information Deterministic ECMP sorts ECMPs in order even though RTM provides them in a random order.
PAGE 589
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. Usage Information You must save the new ECMP settings to the startup-config (write-mem) then reload the system for the new settings to take effect.
PAGE 590
link-bundle-monitor enable Provides a mechanism to enable monitoring of traffic distribution on an ECMP link bundle. Syntax link-bundle-monitor enable To exit from ECMP group mode, use the exit command. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. ECMP-GROUP PORT-CHANNEL INTERFACE Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 591
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. show config Display the ECMP configuration.
PAGE 592
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 593
16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: Topics: • • • • fips mode enable show fips status show ip ssh ssh fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command. Default Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 594
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 595
Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: DellEMC# show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-sha1-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled.
PAGE 596
• • • aes128–ctr: Force ssh to use the aes256–cbc encryption cipher. aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. 3des-cbc: Force ssh to use 3des-cbc encryption cipher. -l username (OPTIONAL) Enter the keyword —l then the user name used in this SSH session. The default is the user name of the user associated with the terminal. -m HMAC algorithm Enter one of the following HMAC algorithms to use. (For v2 clients only.
PAGE 597
NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. Example If FIPS mode is not enabled: DellEMC# ssh 10.10.10.10 ? -c Encryption cipher to use (for v2 clients only) -l User name option -m HMAC algorithm to use (for v2 clients only) -p SSH server port option (default 22) -v SSH protocol version DellEMC# ssh 10.10.10.
PAGE 598
17 FIP Snooping clear fip-snooping database interface vlan Clear FIP snooping information on a VLAN for a specified FCoE MAC address, ENode MAC address, or FCF MAC address, and remove the corresponding ACLs FIP snooping generates. Syntax clear fip-snooping database interface vlan {vlan-id} enode {enode-mac-address} | fcf {fcf-mac-address} | session {session-mac-address} Parameters enode-macaddress Enter the ENode MAC address of the session which has to be cleared.
PAGE 599
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. debug fip snooping Enable debugging on FIP snooping.
PAGE 600
debug fip snooping rx Enable debugging for FIP snooping receive-specific packets. Syntax debug fip-snooping rx packet-type [all | discovery | ns | virtual-linkinstantiation | virtual-link-maintenance| vlan-discovery] [interface] Parameters packet-type Enter the keyword packet-type and then the option type on which to enable debugging. The options are: • • • • • • interface all — Enter the keyword all to enable debugging on all the options.
PAGE 601
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information Before enabling FIP snooping, assign the fcoeacl space using the cam-acl command.
PAGE 602
fip-snooping fc-map Configure the FC-MAP value FIP snooping uses on all VLANs. Syntax fip-snooping fc-map fc-map-value To return the configured FM-MAP value to the default value, use the no fip-snooping fc-map command. Parameters fc-map-value Enter the FC-MAP value FIP snooping uses. The range is from 0EFC00 to 0EFCFF. Defaults 0x0EFC00 Command Modes • • Command History This guide is platform-specific.
PAGE 603
fip-snooping port-mode fcf Configure the port for bridge-to-FCF links. Syntax fip-snooping port-mode fcf To disable the bridge-to-FCF link on a port, use the no fip-snooping port-mode fcf command. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 604
show fip-snooping config Display the FIP snooping status and configured FC-MAP values. Syntax show fip-snooping config Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 605
Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information The following describes the show fip-snooping enode command shown in the following example. Field Description ENode MAC MAC address of the ENode. ENode Interface Slot/ port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. VLAN VLAN ID number the session uses. FC-ID Fibre Channel session ID the FCF assigns.
PAGE 606
Field Description FC-MAP FC-Map value the FCF advertises. ENode Interface Slot/ number of the interface connected to the ENode. FKA_ADV_PERIO D Time (in milliseconds) during which FIP keep-alive advertisements transmit. No of ENodes Number of ENodes connected to the FCF. FC-ID Fibre Channel session ID the FCF assigns. Example DellEMC# show fip-snooping fcf FCF MAC FCF Interface VLAN FC-MAP FKA_ADV_PERIOD No.
PAGE 607
Field Description Number of Unicast Number of FIP-snoop unicast discovery solicit frames received on the interface. Discovery Solicits Number of FLOGI Number of FIP-snoop FLOGI request frames received on the interface. Number of FDISC Number of FIP-snoop FDISC request frames received on the interface. Number of FLOGO Number of FIP-snoop FLOGO frames received on the interface Number of ENode Keep Alives Number of FIP-snoop ENode keep-alive frames received on the interface.
PAGE 608
Number of FLOGI Rejects :0 Number of FDISC Accepts :16 Number of FDISC Rejects :0 Number of FLOGO Accepts :0 Number of FLOGO Rejects :0 Number of CVL :0 Number of FCF Discovery Timeouts :0 Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 DellEMC(conf)# DellEMC# show fip-snooping statistics int tengigabitethernet 1/11 Number of Vlan Requests :1 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :1 Number of Unicast Discovery Solicits :0 Number of
PAGE 609
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 610
show fips status Display the FIPs status on the platform. Syntax show fips status Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 610 FIP Snooping Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500.
PAGE 611
18 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember • • • • • • • FRRP is media- and speed-independent.
PAGE 612
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 613
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 614
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol. Syntax disable To enable the Resilient Ring Protocol, use the no disable command. Defaults Disabled Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific.
PAGE 615
To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 616
member-vlan Specify the member VLAN identification numbers. Syntax member-vlan {vlan-range} To return to the default, use the no member-vlan [vlan-range] command. Parameters vlan-range Enter the member VLANs using VLAN IDs (separated by commas), a range of VLAN IDs (separated by a hyphen), a single VLAN ID, or a combination. For example: VLAN IDs (comma-separated): 3, 4, 6. Range (hyphen-separated): 5-10. Combination: 3, 4, 5-10, 8.
PAGE 617
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 618
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced Usage Information This command places you into the resilient ring protocol. After executing this command, the command line prompt changes to conf-frrp. show frrp Display the resilient ring protocol configuration. Syntax show frrp [ring-id [summary]] | [summary] Parameters ring-id Enter the ring identification number.
PAGE 619
Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell EMC Networking OS requires a command line confirmation before the command is executed.
PAGE 620
2 UP Master 31 UP Transit 50 Down Transit DellEMC# Example (1) 11-20, 25,27-30 40-41 32 DellEMC# show frrp 1 Ring protocol 1 is in Master mode Ring Protocol Interface: Primary : TenGigabitEthernet 1/16 State: Forwarding Secondary: Port-channel 100 State: Blocking Control Vlan: 1 Ring protocol Timers: Hello-Interval 50 msec Dead-Interval 150 msec Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348 Number of state Changes: 34 Member Vla
PAGE 621
Defaults • • Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 500 ms for hello-interval milliseconds 1500 ms for dead-intervalmilliseconds Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 622
19 GARP VLAN Registration (GVRP) The Dell EMC Networking operating system supports the basic GVRP commands on the Dell EMC Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 623
• • • show garp timers show gvrp show gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface. Syntax Parameters clear gvrp statistics interface interface interface interface Enter the following keywords and the interface information: • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information.
PAGE 624
Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events. pdu Enter the keyword pdu then one of the following Interface keywords and the interface information: • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information.
PAGE 625
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 626
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 627
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • disable — globally disable GVRP. gvrp registration Configure the GVRP register type. Syntax gvrp registration {fixed | normal | forbidden} To return to the default, use the gvrp register normal command.
PAGE 628
Usage Information Fixed registration prevents an interface, configured using the command line, to belong to a VLAN (static configuration) from being unconfigured when it receives a Leave message. Therefore, Registration mode on that interface is fixed. Normal registration is the default registration. The port’s membership in the VLAN depends on GVRP. The interface becomes a member of a VLAN after learning about the VLAN through GVRP.
PAGE 629
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 630
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Example Related Commands DellEMC# show garp timers GARP Timers Value (milliseconds) ---------------------------------------Join Timer 200 Leave Timer 600 LeaveAll Timer 10000 DellEMC# • garp timers — set the intervals (in milliseconds) for sending GARP messages. show gvrp Display the GVRP configuration.
PAGE 631
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Usage Information If no ports are GVRP participants, the message output changes from GVRP Participants running on to GVRP Participants running on no ports. Example Related Commands DellEMC# show gvrp brief GVRP Feature is currently enabled.
PAGE 632
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Usage Information Invalid messages/attributes skipped can occur in the following cases: • • • • • • The incoming GVRP PDU has an incorrect length.
PAGE 633
20 High Availability (HA) High availability (HA) in the Dell EMC Networking OS is the configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol. You must specifically enable some protocols for HA.
PAGE 634
Usage Information Enabling this command keeps the failed RPM in the failed state. If there are two RPMs in the system, enabling this command prevents the failed RPM from becoming a working Standby RPM. If there is only one RPM in the system, the failed RPM does not recover and affects the system. redundancy force-failover Force the secondary stack unit to become the primary stack unit.
PAGE 635
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 8.1.1.
PAGE 636
Field Description • • The state of the RPM: Active, Standby, Booting, or Offline. Whether the link to the second RPM is up or down. PEER RPM Status Displays the state of the second RPM, if present RPM Redundancy Configuration Displays the following information: • • • • • which RPM is the preferred Primary on next boot (the redundancy primary command) the data sync method configured (the redundancy synchronize command) the failover type (you cannot change this type; it is software-dependent).
PAGE 637
Last failover Reason: User request -- Last Data Block Sync Record: ------------------------------------------------Line Card Config: succeeded Jul 13 2007 21:28:53 Start-up Config: succeeded Jul 13 2007 21:28:53 SFM Config State: succeeded Jul 13 2007 21:28:53 Runtime Event Log: succeeded Jul 13 2007 21:28:53 Running Config: succeeded Jul 13 2007 21:28:53 DellEMC# High Availability (HA) 637
PAGE 638
21 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 4. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 638 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 639
Symbol Type Code 12 Description Query Error parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 640
22 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell EMC Networking OS. Topics: • • IGMP Commands IGMP Snooping Commands IGMP Commands Dell EMC Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember • • • • • • • Dell EMC Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent source-specific multicast (PIM-SSM) include and exclude modes.
PAGE 641
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 642
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 643
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. Usage Information The access list accepted is an extended ACL. To block IGMP reports from hosts, on a per-interface basis based on the group address and source address that you specify in the access list, use this feature.
PAGE 644
a group from the membership database. This command provides a way to achieve the immediate deletion. In addition, this command provides a way to enable immediate-leave processing for specified groups. ip igmp last-member-query-interval Change the last member query interval, which is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages. This interval is also the interval between Group-Specific Query messages.
PAGE 645
To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 646
Parameters seconds Enter the number of seconds for the maximum response time. The range is from 1 to 25. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 647
source-address Specify the multicast source address to which the groups are mapped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 648
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Changed the default IGMP from version 2 to version 3. Introduced on the S6000-ON 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 649
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series and C-Series. 7.5.1.
PAGE 650
Example (Details) 225.0.0.1 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.2 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.3 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.4 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 DellEMC# show ip igmp group details Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.
PAGE 651
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results.
PAGE 652
IGMP immediate-leave is disabled IGMP activity: 0 joins IGMP querying router is 50.30.124.1 IGMP version is 3 DellEMC# show ip igmp ssm-map Display is a list of groups that are currently in the IGMP group table and contain SSM mapped sources. Syntax show ip igmp [vrf vrf-name] ssm-map [group] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 653
65.0.0.2 65.0.0.3 65.0.0.4 65.0.0.5 Related Commands • 00:01:22 00:01:22 00:01:22 00:01:22 ip igmp ssm-map — use a statically configured list to translate (*,G) memberships to (S,G) memberships. IGMP Snooping Commands Dell EMC Networking OS supports IGMP Snooping version 2 and 3 on all Dell EMC Networking systems. Important Points to Remember for IGMP Snooping • • • • • • • • • • Dell EMC Networking OS supports version 1, version 2, and version 3 hosts.
PAGE 654
• • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a port channel interface, enter the keywords port-channel then a number. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 655
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, Z9000, and Z9500. Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. This command displays packets for IGMP and IGMP snooping. ip igmp snooping enable Enable IGMP snooping on all or a single VLAN.
PAGE 656
ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 657
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Seris and S-Series. 7.7.1.0 Introduced on the E-Series.
PAGE 658
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This last-member-query-interval is also the interval between successive Group-Specific Query messages.
PAGE 659
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information The Dell EMC Networking OS provides the capability of statically configuring the interface to which a multicast router is attached.
PAGE 660
Version Description E-Series legacy command Usage Information This command enables the IGMP switch to send General Queries periodically. This behavior is useful when there is no multicast router present in the VLAN because the multicast traffic is not routed. Assign an IP address to the VLAN interface for the switch to act as a querier for this VLAN. show ip igmp snooping groups Display snooping related information for all the IGMP groups, interface or one group of one interface.
PAGE 661
Field Description Interface Lists the interface type, slot and port number. Mode Displays the IGMP version used. Uptime Displays the amount of time the group has been operational. Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. Member Ports Indicates the port channel.
PAGE 662
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information If the port channel is a VLT port channel, an asterisk (*) after the port channel number (Po 100*) indicates the port channel is locally down and that a remote VLT port is up. Example Related Commands 662 DellEMC# show ip igmp snooping mrouter Interface Router Ports Vlan 2 Te 1/3, Po 1 DellEMC# • • ip igmp snooping mrouter — configure a static connection to the multicast router.
PAGE 663
23 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • • • • • • Basic Interface Commands Egress Interface Selection (EIS) Commands Port Channel Commands Time Domain Reflectometer (TDR) Commands UDP Broadcast Commands ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 664
corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. vrrp [ipv6 {vr-id} | (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To clear vr-id] the counters of VRRP groups on all IPv6 interfaces, enter ipv6. To clear the counters of a specified group, enter a VRID number from 1 to 255.
PAGE 665
clear dampening Clear the dampening counters on all the interfaces or just the specified interface. Syntax Parameters clear dampening [interface] interface (OPTIONAL) Enter any of the following keywords and the interface information to clear counters from a specified interface: • • • For a Port Channel interface, enter the keywords port-channel then a number. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 666
dampening Configure dampening on an interface. Syntax dampening [[[[half-life] [reuse-threshold]] [suppress-threshold]] [maxsuppress-time]] Parameters half-life Enter the number of seconds after which the penalty is decreased. The penalty decreases half after the half-life period expires. The range is from 1 to 30 seconds. The default is 5 seconds. reuse-threshold Enter a number as the reuse threshold, the penalty value below which the interface state is changed to “up”. The range is from 1 to 20000.
PAGE 667
NOTE: You cannot apply dampening on an interface that is monitoring traffic for other interfaces. Example Related Commands DellEMC(conf-if-te-1/10)# dampening 20 800 4500 120 DellEMC(conf-if-te-1/10)# • • clear dampening — clear the dampening counters on all the interfaces or just the specified interface. show interfaces dampening — display interface dampening information. default interface Reset a physical interface to its factory default settings.
PAGE 668
DellEMC(conf)# default interface tengigabitethernet 1/5 DellEMC(conf-if-te-1/5)# show config ! interface TenGigabitEthernet 1/5 no ip address shutdown Related Commands • show running-config – display the current configuration. description Assign a descriptive text string to the interface. Syntax description desc_text To delete a description, use the no description command. Parameters desc_text Enter a text string up to 240 characters long.
PAGE 669
• • • Entering a text string after the description command overwrites any previous text string that you previously configured as the description. The shutdown and description commands are the only commands that you can configure on an interface that is a member of a port-channel. Use the show interfaces description command to display descriptions configured for each interface. duplex (10/100 Interfaces) Configure duplex mode on the Management Interface interfaces where the speed is set to 10/100.
PAGE 670
encapsulation dot1q Configures lite-subinterfaces. Syntax encapsulation dot1q vlan-id To remove a previously configured lite-subinterface, use the no encapsulation dot1q vlan-id command. Parameters Command Modes Command History dot1q vlan-id Enter the keyword dot1q followed by the VLAN ID to which the host belongs. The range is from 1 to 4094.
PAGE 671
Version Description 9.14(1.0) Introduced arp-inspection option. 9.14(0.0) Introduced on the platforms S4048–ON, S6100–ON, Z9100–ON, S4048T-ON, S3048– ON, S6000, S6010–ON, S5048F-ON, FN-IOM and MXL. 9.13(0.2P2) Introduced on the S3100. Usage Information This command has to be configured before the interface moves to Err-disabled state. If not, the recovery action is not performed. Related Commands errdisable recovery interval— Configure recovery timer interval for an interface.
PAGE 672
rx off Enter the keywords rx off to ignore the received flow control frames on this port. tx on Enter the keywords tx on to send control frames from this port to the connected device when a higher rate of traffic is received. tx off Enter the keywords tx off so that flow control frames are not sent from this port to the connected device when a higher rate of traffic is received. pause-threshold Enter the buffer threshold limit for generating PAUSE frames.
PAGE 673
• • • Do not enable tx pause when buffer carving is enabled. For information and assistance, consult Dell EMC Networking TAC. The only configuration applicable to half duplex ports is rx off tx off. The following error is returned: Can’t configure flowcontrol when half duplex is configure, config ignored Half duplex cannot be configured when the flow control configuration is on (default is rx on tx on).
PAGE 674
LocNegRx off off off off LocNegTx RemNegRx RemNegTx off off off off off off off off off off off off off off off off off off on off off off on off off off off off off on on on off off on on off off on on off on on on off off on on off off on on off off on on off off on on interface Configure a physical or virtual interface on the switch.
PAGE 675
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added the support for interfaces. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.
PAGE 676
Slot/Port information need not contain a space before and after the dash. For example, both of the following commands are valid: interface group tengigabitethernet 1/1 - 1/5; interface group tengigabitethernet 1/1-1/5. • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information.
PAGE 677
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 678
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Usage Information You cannot delete a Management port.
PAGE 679
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Usage Information You cannot delete the Null interface. The only configuration command possible in a Null interface is ip unreachables.
PAGE 680
Version Description 9.14(0.0) Updated the error message when no ports are configured within the specified interface range. 9.13(0.0) Introduced the Configuration Terminal Batch mode on C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P2) Introduced on the S4038-ON. 9.8(0.0P5) Introduced on the S3048-ON. 9.7(0.
PAGE 681
Example (Configuration Terminal Batch Mode) Example (Multiple Ports) Example (Overlapping Ports) DellEMC(conf-b)#interface range te 1/1-4 DellEMC(conf-if-range-te-1/1-4)# DellEMC(conf)# interface range tengigabitethernet 2/10 - 2/23, tengigabitethernet 2/12 - 2/17 DellEMC(conf-if-range-te-2/10-2/23)# DellEMC(conf)# interface range tengigabitethernet 2/3 - 2/11, tengigabitethernet 2/3 - 2/23 DellEMC(conf-if-range-te-2/3-2/23)# Usage Information Only VLAN and port-channel interfaces created using the inte
PAGE 682
Secondary VLT Dec 6 10:43:17 %RPM1-P:CP %CLIBATCH-6-CLI_BATCH_CONFIG_IN_PROGRESS_TRAP: Batch configuration commit is in progress Dec 6 10:43:18 %RPM1-P:CP %CLIBATCH-6-CLI_BATCH_CONFIG_COMPLETE_TRAP: Batch configuration commit is success Related Commands • • • • • interface port-channel — configure a port channel group. interface vlan — configure a VLAN interface. show config (from INTERFACE RANGE mode) — display the bulk configuration interfaces. show range — display the bulk configuration ranges.
PAGE 683
Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Example (Single Range) This example shows how to define an interface range macro named test. Execute the show running-config command to display the macro definition.
PAGE 684
Example (Single Range) Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced This example shows the macro named test that was defined earlier. DellEMC(config)# interface range macro test DellEMC(config-if-range-te-1/1-3,te-5/1-47,te-2/1-89)# Dell Related Commands • • interface range — configure a range of command (bulk configuration).
PAGE 685
FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs and IP ACLs are supported. For more information, see Access Control Lists (ACL). The following features are not supported on VLANs associated with an OpenFlow instance: • • • IPv4 IPv6 MTU If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously.
PAGE 686
Related Commands • • • • Interfaces — configure a physical interface. interface loopback — configure a loopback interface. interface null — configure a null interface. interface port-channel — configure a port channel group. keepalive Send keepalive packets periodically to keep an interface alive when it is not transmitting data. Syntax keepalive To stop sending keepalive packets, use the no keepalive command. Defaults Enabled.
PAGE 687
• • • • • • For the Management interface on the stack-unit, enter the keyword managementEthernet then the slot/port information. For a port channel interface, enter the keyword port-channel and then a number. For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 688
Example (Single Interface) Key Description r Change the [delta] column from change in the number of packets/bytes in the last interval to rate per second. l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis. a Change the view to the previous interface on the line card, or if in line card mode, the previous line card in the chassis. T Increase the screen refresh rate. t Decrease the screen refresh rate. q Return to the CLI prompt.
PAGE 689
Te 1/19 Down 0 0 0 0 Te 1/20 Up 62734 54 62766 18 Te 1/21 Up 60198 9 200899 9 Te 1/22 Up 17304741100 3157554 10102508511 1114221 Te 1/23 Up 17304769659 3139507 7133354895 523329 m - Change mode c - Clear screen b - Display bytes r - Display pkts/bytes per sec l - Page up a - Page down mtu Set the link maximum transmission unit (MTU) (frame size) for an Ethernet interface. Syntax mtu value To return to the default MTU value, use the no mtu command. Parameters value Enter a maximum frame size in bytes.
PAGE 690
• • All members must have the same link MTU value and the same IP MTU value. The port channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the channel members. For example, if the members have a link MTU of 2100 and an IP MTU 2000, the port channel’s MTU values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU. VLANs: • • • All members of a VLAN must have same IP MTU value. Members can have different Link MTU values.
PAGE 691
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. Usage Information The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits. The negotiation auto command provides a mode option for configuring an individual port to forced-master/ forced slave after you enable auto-negotiation.
PAGE 692
Input Statistics: ... User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces.
PAGE 693
port-delay-restore (Configuration Mode) Allows a delayed bring up of all interfaces during switch boot up. Syntax port-delay-restore value To return to the default value, use the no port-delay-restore command. Parameters value Enter a timer value from 1 second to 300 seconds. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command-Line Reference Guide.
PAGE 694
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information The following describes the interface command shown in the following example. This example sets a port as hybrid, makes the port a tagged member of VLAN 20, and an untagged member of VLAN 10, which becomes the native VLAN of the port.
PAGE 695
Parameters seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds. NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value. For example, if 44 seconds is designated, it rounds to 30; 45 to 59 seconds rounds to 45. Defaults 299 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 696
entire buffer is cleared; the show int stats command shows the rate information to be 0 as the polling interval is less than 5. Defaults 299 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced on all Dell EMC Networking OS platforms.
PAGE 697
Example Version Description pre-Version 6.2.1.0 Introduced on the E-Series. DellEMC(conf-if-fo-1/49)# show config ! interface fortyGigE 1/49 no ip address mtu 9216 switchport no shutdown DellEMC(conf-if-fo-1/49)# DellEMC(conf-if-te-1/50)# show config ! interface Tengigabitethernet 1/50 no ip address mtu 9216 switchport no shutdown DellEMC(conf-if-te-1/50)# show config (from INTERFACE RANGE mode) Display the bulk configured interfaces (interface range).
PAGE 698
Example DellEMC(conf)# interface range tengigabitethernet 1/1 - 2 DellEMC(conf-if-range-gi-1/1-2)# show config ! interface TenGigabitEthernet 1/1 no ip address switchport no shutdown ! interface TenGigabitEthernet 1/2 no ip address switchport no shutdown DellEMC(conf-if-range-gi-1/1-2)# show interfaces Display information on a specific physical interface or virtual interface.
PAGE 699
Version Description Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000ON, S6100, Z9500, S6010, and Z9100. Included display information about EEE on the S3048–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. Included display information about EEE on the S3100 series, S4820T, and S5000. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.
PAGE 700
Line Description TenGigabitEthern et 1/1... Interface type and administrative and line protocol status. Hardware is... Interface hardware information, assigned MAC address, and current address. Pluggable media present... Present pluggable media wavelength, type, and rate.
PAGE 701
Line Description • • • • • Vlans = number of VLAN tagged packets throttles = packets containing PAUSE frames discarded = number of packets discarded without any processing collisions = number of packet collisions wred=count both packets discarded in the MAC and in the hardware-based queues Rate information... Estimate of the input and output traffic rate over a designated interval (30 to 299 seconds). Traffic rate is displayed in bits, packets per second, and percent of line rate. Time since...
PAGE 702
Example Example (Management Ethernet) Example (Management Ethernet, two IPv6 addresses) DellEMC# show interfaces tengigabitethernet 1/1 TenGigabitEthernet 1/1 is up, line protocol is down Hardware is DellEMCEth, address is 00:01:e8:41:77:95 Current address is 00:01:e8:41:77:95 Pluggable media present, SFP type is 1000BASE-SX Wavelength is 850nm Interface index is 100974648 Port will not be disabled on partial SFM failure Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit Fl
PAGE 703
Link local IPv6 address: fe80::201:e8ff:fea0:bff3/64 Global IPv6 address: 1::1/ Global IPv6 address: 2::1/64 Virtual-IP is not set Virtual-IP IPv6 address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time
PAGE 704
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Changed the organization of the display output.
PAGE 705
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • • For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 706
Related Commands • • dampening — configure dampening on an interface. show interfaces configured — display any interface with a non-default configuration. show interfaces phy Display auto-negotiation and link partner information. Syntax show interfaces gigabitethernet slot/port phy Parameters tengigabitetherne t Enter the keyword tengigabitethernet then the slot or port information. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 707
AutoNegotiation Advertise Displays the control words the local interface advertises during negotiation. Duplex is either half or full. Asym- and Sym Pause is the types of flow control the local interface supports. AutoNegotiation Remote Partner’s Ability Displays the control words the remote interface advertises during negotiation. Duplex is either half or full. Asym- and Sym Pause is the types of flow control the remote interface supports.
PAGE 708
Sym Pause: False AutoNegotiation Expansion: ParallelDetectionFault: False ... show interfaces stack-unit Display information on all interfaces on a specific S-Series or Z-Series stack member. Syntax show interfaces stack-unit unit-number Parameters unit-number Enter the stack member number. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 709
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 710
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 711
• • stack-unit unit-id For physical interfaces, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4. For port–channel interfaces, you can specify multiple ports as port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces port—channel 1 - 4.
PAGE 712
802.1QTagged: Hybrid Vlan membership: Vlan 2, Vlan 20 Native VlanId: 20 Name: TenGigabitEthernet 1/2 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/3 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/4 802.1QTagged: True Vlan membership: Vlan 2 --More-Related Commands • • • interface — configure a physical interface on the switch. show ip interface — display Layer 3 information about the interfaces.
PAGE 713
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 714
Line Description TX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp High Factory-defined setting. Value can differ between SFP and SFP+. Warning threshold Voltage High Factory-defined setting. Value can differ between SFP and SFP+. Warning threshold Bias High Warning Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 715
Line Description Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above. Tx Bias High Alarm This can be either true or false, depending on the present Tx bias current value displayed Flag above. Tx Power High Alarm Flag This can be either true or false, depending on the Current Tx bias power value displayed above. Rx Power High Alarm Flag This can be either true or false, depending on the Current Rx power value displayed above.
PAGE 716
SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP 0 0 0 0 0 0 0 0 0 0 0 0 Length(62.5um) 10m = 0x0f Length(Copper) 10m = 0x00 Vendor Rev = A Laser Wavelength = 850 nm CheckCodeBase = 0x66 Serial Extended ID fields Options = 0x00 0x12 BR max= 0 BR min= 0 Vendor SN= P5N1ACE Datecode = 040528 CheckCodeExt = 0x5b SFP 1 Diagnostic Information =================================== SFP 1 Rx Power measurement type = Average =================================== SFP 1 Temp High Alarm threshold = 95.
PAGE 717
show interfaces vlan Display VLAN statistics. Syntax Parameters show interfaces vlan {vlan-id} [LINE] {description} vlan-id Enter the interface VLAN number. The range is from 1 to 4094. LINE (OPTIONAL) Enter the name of the VLAN. description Displays the VLAN interface information with description. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 718
Command Modes INTERFACE RANGE (config-if-range) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 719
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. • ecmp-group — configure a mechanism to monitor traffic distribution. show system stack-unit fanout configured Displays the details about the fanned-out ports.
PAGE 720
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.
PAGE 721
100 Enter the keyword 100 to set the interface’s speed to 10/100 Mb/s. NOTE: When this setting is enabled, only 100Base-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s. Auto-negotiation is enabled. For more information, refer to negotiation auto. NOTE: When this setting is enabled, only 1000Base-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card.
PAGE 722
If you use an active optical cable (AOC), you can convert the QSFP+ port to a 10 Gigabit SFP+ port or 1 Gigabit SFP port. Use the speed command to enable the required speed. NOTE: If the interface does not come up when you configure 10/100/1000G speed, configure the interface speed using the speed command manually on both the ends and disable autonegotiation if it is enabled. speed (Management interface) Set the speed for the Management interface.
PAGE 723
stack-unit portmode quad Configures the list of dynamic fan-out capable ports. Syntax stack-unit [stack-unit number] port port-number portmode quad To remove the quad-port configuration, use the command. Parameters stack-unit number Enter the port number. The range is from 1 to 6. Defaults 49,50,51,52,53,54 Command Modes CONFIGURATION Command History Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.
PAGE 724
port-channel (OPTIONAL) Enter the keywords port-channel if the backup port is a static or dynamic port channel. mode (OPTIONAL) Enter the keyword mode to set the interface mode. private-vlan (OPTIONAL) Enter the keywords private-vlan to set the interface mode to private VLAN mode. host (OPTIONAL) Enter the keyword host to set the private VLAN interface to host mode. promiscuous (OPTIONAL) Enter the keyword promiscuous to set the private VLAN interface to promiscuous mode.
PAGE 725
Egress Interface Selection (EIS) Commands The following commands are Egress Interface Selection (EIS) commands. application Configure the management egress interface selection. Syntax application {all | application-type} To remove a management application configuration, use the no application {all | applicationtype} command. Parameters application-type Enter any of the following keywords: • • • • • • • • • • • all For DNS, enter the keyword dns. For FTP, enter the keyword ftp.
PAGE 726
• • all For HTTP, enter the keyword http. For ICMP, enter the keyword icmp. Configure all applications. Defaults None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.
PAGE 727
Version Description 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T. management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface. Syntax management egress-interface-selection To disable and remove management egress interface selection (EIS) configurations, use the no management egress-interface-selection command. Defaults None.
PAGE 728
show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Syntax show management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.
PAGE 729
sflow-collector snmp ssh syslog tacacs telnet tftp : : : : : : : 0 0 2 0 0 0 0 Port Channel Commands A Link Aggregation Group (LAG) is a group of links that appear to a MAC client as if they were a single link according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a Port Channel. • The platform supports 128 port channels and 16 members per port channel.
PAGE 730
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Usage Information Use the interface port-channel command to access this command.
PAGE 731
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 732
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.3.11.1 Introduced on Z9000. 8.1.1.0 Introduced on E-Series. 7.6.1.0 Introduced on S-Series. 7.5.1.0 Introduced on C-Series. pre-Version 6.2.1.0 Introduced on E-Series. Usage Information Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by using the switchport command) or Layer 3 mode (by configuring an IP address).
PAGE 733
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 734
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Usage Information This feature groups two LAGs to work in tandem as a supergroup.
PAGE 735
show interfaces port-channel Display information on configured Port Channel groups. ` Syntax Parameters show interfaces port-channel [channel-number] [brief] [description] channel-number For a Port Channel interface, enter the keyword port-channel then a number. The range is from 1 to 128. NOTE: This command also enables you to view information corresponding to a range of ports. • For port-channel interfaces, you can specify multiple ports as portrange.
PAGE 736
Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fate-sharing group (“Failover-group”) is listed. Hardware is... Displays the interface’s hardware information and its assigned MAC address. Port-channel is part... Indicates whether the LAG is part of a LAG fate-sharing group (“Failover-group”). Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed. MTU 1554...
PAGE 737
DellEMC# User Information The following describes the show interfaces port-channel brief command shown in the following example. Field Description LAG Lists the port channel number. Mode Lists the mode: • • Status L3 — for Layer 3 L2 — for Layer 2 Displays the status of the port channel. • • down — if the port channel is disabled (shutdown) up — if the port channel is enabled (no shutdown) Uptime Displays the age of the port channel in hours:minutes:seconds.
PAGE 738
destination-ip address source-port number destination-port number source-mac address destination-mac Enter the keywords destination-ip then the IP destination address in IP address format. Enter the keywords source-port then the source port number. The range is from 1 to 65536. The default is None. Enter the keywords destination-port then the destination port number. The range is from 1 to 65536. The default is None.
PAGE 739
Example DellEMC# show port-channel-flow outgoing-port-channel 1 incoming-interface te 3/3 source-mac 00:00:50:00:00:00 destination-mac 00:00:a0:00:00:00 Egress Port for port-channel 1, for the given flow, is Te 13/2 Time Domain Reflectometer (TDR) Commands TDR is useful for troubleshooting an interface that is not establishing a link; either it is flapping or not coming up at all. TDR detects open or short conditions of copper cables on 100/1000 Base-T modules.
PAGE 740
Usage Information The interface must be enabled to run the test or an error message is generated: DellEMC# tdr-cable-test tengigabitethernet 11/1 % Error: Interface is disabled Te 11/1. Syslog messages are generated when the link flaps during TDR tests. Related Commands • show tdr — display the results of the TDR test. show tdr Display the TDR test results.
PAGE 741
Status Definition Length: 93 (+/- 1) meters, Status: Open An opening is detected on the cable. The location, in this Example is 93 meters. The open is accurate to plus or minus one meter. Status: Impedance There is an impedance mismatch in the cables.
PAGE 742
Version Description Pre-version 8.3.7.0 Introduced on the E-Series. Example DellEMC# debug ip udp-helper UDP helper debugging is on 01:20:22: Pkt rcvd on Gi 3/0 with IP DA (0xffffffff) will be sent on Gi 5/1 Gi 5/2 Vlan 3 01:44:54: Pkt rcvd on Gi 4/0 is handed over for DHCP processing. DellEMC# debug ip udp-helper UDP helper debugging is on 01:20:22: Pkt rcvd on Te 3/0 with IP DA (0xffffffff) will be sent on Gi 5/1 Gi 5/2 Vlan 3 01:44:54: Pkt rcvd on Te 4/0 is handed over for DHCP processing.
PAGE 743
Usage Information If you configure the ip helper-address command and ip udp-helper udp-port command, the behavior is that the UDP broadcast traffic with port numbers 67/68 is unicast relayed to the DHCP server per the ip helper-address configuration. This occurs regardless if the ip udp-helper udp-port command contains port numbers 67/68 or not.
PAGE 744
• • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a port channel interface, enter the keywords port-channel then a number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 745
24 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: • • • Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 746
• • espauthentication Enter the keywords esp-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. • • • esp-encryption sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. null — Causes an encryption policy configured for the area to not be inherited on the interface. md5 — Use Message Digest 5 (MD5) authentication. sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication.
PAGE 747
Parameters name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.
PAGE 748
match Apply an match filter to the crypto policy. Syntax match seq-num tcp [sourceip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] To remove the match filter for the crypto map, use the no match seq-num tcp [source ip address | ipv6 address {mask} {source-port number}] [destination ip address | ipv6 address {mask} {destination-port number}] command. Parameters seq-num Enter the match command sequence number.
PAGE 749
To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec. ah Use the AH protocol when you select the AH transform set in the crypto policy. esp Use the ESP protocol when you select the ESP transform set in the crypto policy. spi Enter the security parameter index number.
PAGE 750
Example DellEMC# show crypto ipsec transform-set Transform-Set Name Transform-Set refCnt AH Transform ESP Auth Transform ESP Encry Transform DellEMC# : dallas : 0 : : : 3des show crypto ipsec policy Display the crypto policy configuration. Syntax show crypto ipsec policy Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.
PAGE 751
DellEMC(conf-crypto-policy)# transform-set Specify the transform set the crypto policy uses. Syntax transform-set transform-set-name To delete a transform set from the crypto policy, use the no transform-set transform-set-name command. Parameters transform-setname Enter the name for the crypto policy transform set. Defaults None Command Modes CONFIG-CRYPTO-POLICY Command History This guide is platform-specific.
PAGE 752
25 IPv4 Routing The basic IPv4 commands are supported by Dell EMC Networking OS on the platform.
PAGE 753
• • • • • • show ip protocols show ip route show ip route list show ip route summary show ip traffic show tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF.
PAGE 754
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. Usage Information You cannot use Class D or Class E IP addresses or zero IP address (0.0.0.0) when creating a static ARP. Zero MAC addresses (00:00:00:00:00:00) are also invalid. You can use the vrf attribute of this command to create a static ARP entry on either a default or a non-default VRF.
PAGE 755
Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses. Related Commands • show arp retries — display the configured number of ARP retries. arp learn-enable Enable ARP learning using gratuitous ARP.
PAGE 756
max-number Enter the maximum number of ARP entries that a VRF RTM can hold. The range is from 0 to 65535. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 757
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Usage Information Retries are 20 seconds apart. Related Commands • show arp retries — display the configured number of ARP retries. arp timeout Set the time interval for an ARP entry to remain in the ARP cache. Syntax Parameters arp timeout minutes minutes Enter the number of minutes. The range is from 0 to 35790. The default is 240 minutes.
PAGE 758
clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM). Syntax clear arp-cache [vrf vrf-name | interface | ip ip-address] [no-refresh] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear the ARP cache corresponding to that VRF.
PAGE 759
Version Description 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. clear host Remove one or all dynamically learned host table entries. Syntax Parameters clear host name name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 760
vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all FIB entries corresponding to that VRF. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 761
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.9.1.
PAGE 762
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 763
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series(the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 764
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series. Example Related Commands DellEMC# debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.17 BOOTP Request, hops = 0, XID = 0xbf05140f, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 0.0.0.0 00:12:21 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for 00:60:CF:20:7B:8C to 14.4.4.
PAGE 765
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000 and Z-Series. debug ip icmp View information on the internal control message protocol (ICMP).
PAGE 766
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option. ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.
PAGE 767
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094).
PAGE 768
IP Fragment, Ident = 4741, fragment offset = 1480 IP: s=40.40.40.40 (local), d=224.0.0.5 (Te 4/11), len 64, sending broad/ multicast proto=89 IP: s=40.40.40.40 (local), d=224.0.0.6 (Te 4/11), len 28, sending broad/ multicast proto=2 IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable ICMP type=8, code=0 IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable ICMP type=8, code=0 Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option.
PAGE 769
ip address Assign a primary and secondary IP address to the interface. Syntax ip address ip-address mask [secondary] To delete an IP address from an interface, use the no ip address [ip-address] command. Parameters ip-address Enter an IP address in dotted decimal format. mask Enter the mask of the IP address in slash prefix format (for example, /24). secondary (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Defaults Not configured.
PAGE 770
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 771
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information To configure a list of possible domain names, configure the ip domain-list command up to six times.
PAGE 772
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information To fully enable DNS, also specify one or more domain name servers with the ip name-server command. Dell EMC Networking OS does not support sending DNS queries over a VLAN.
PAGE 773
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Usage Information You can only configure one domain name with the ip domain-name command. To configure more than one domain name, configure the ip domain-list command up to six times.
PAGE 774
Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information You can add multiple DHCP servers by entering the ip helper-address command multiple times. If multiple servers are defined, an incoming request is sent simultaneously to all configured servers and the reply is forwarded to the DHCP client.
PAGE 775
Usage Information This command disables the incrementing of the hops field when boot requests are relayed to a DHCP server through Dell EMC Networking OS. If the incoming boot request already has a non-zero hops field, the message is relayed with the same value for hops. However, the message is discarded if the hops field exceeds 16, to comply with the relay agent behavior specified in RFC 1542.
PAGE 776
ip icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv4 packets.
PAGE 777
In network environments that contain a large number of devices, ranging up to thousands of systems, and with each device configured for equal-cost multipath (ECMP) links, you cannot effectively and optimally use the traceroute and ping applications to examine the network reachablity and identify any broken links for diagnostic purposes.
PAGE 778
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 platforms. Usage Information You can enable the mechanism to configure the source or the originating interface from which the packet (the device that generates the ICMP error messages) is received by the switch to send the loopback address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output.
PAGE 779
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series. Usage Information To avoid denial of service (DOS) attacks, keep the number of fragments allowed for re-assembly low. ip max-routes Enables you to configure the maximum number of protocol routes per VRF that are allowed for IPv4.
PAGE 780
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 781
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 782
IPv6 route using a next-hop IPv6 address in order for the ping command to detect the destination address. interface ip- address Enter the keyword interface then the IP address. distance (OPTIONAL) Enter the value of the distance metric assigned to the route. The range is from 1 to 255. name description (OPTIONAL) Enter the keyword name and the description for the IPv4 static route configuration.
PAGE 783
Version Description 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information Using the following example of a static route: ip route 33.33.33.0 /24 tengigabitethernet 1/1 172.31.5.
PAGE 784
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 785
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. load-balance By default, for C-Series and S-Series, Dell EMC Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths.
PAGE 786
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.
PAGE 787
• • • • protocol — Use IPv4 protocol field in hash calculation. vlan — Use vlan field in hash calculation. L4-source-port — Use IPv4 L4-source-port field in hash calculation. L4-dest-port — Use IPv4 L4-dest-port field in hash calculation.
PAGE 788
management route Configure a static route that points to the Management interface or a forwarding router. Syntax management route {ip-address mask | ipv6-address 1.1.1.1prefix-length} {forwarding-router-address | managementethernet | fortyGigE | vlan | tengigabitethernet } To remove a static route, use the no management route command. Parameters ip-address mask Enter an IP address (dotted decimal format) and mask (/prefix format) of the destination subnet.
PAGE 789
Version Description pre-6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix are not reflected in the hardware routing tables. Separate routing tables are maintained for IPv4 and IPv6 management routes. This command manages both tables.
PAGE 790
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF and added usage information for the clear arp-cache command. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 791
Example DellEMC> show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU ------------------------------------------------------------Internet 192.2.1.254 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.253 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.252 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.251 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.250 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.251 1 00:00:c0:02:01:02 Te 2/13 CP Internet 192.2.1.
PAGE 792
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 793
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show hosts command in the following example. Field Description Default domain... Displays the domain name (if configured). Name/address lookup... States if DNS is enabled on the system. Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address.
PAGE 794
port-set pipenumber Enter the keyword port-set then the number of the stack unit’s port-pipe. The unit ID range is from 0 to 0. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display CAM entries corresponding to that VRF. network mask [longer-prefixes [ecmp-group detail]] (OPTIONAL) Enter the IP address and mask of a route to CAM entries for that route only. You can enter one of the following keywords to filter results.
PAGE 795
Field Description V Id Displays the VLAN ID. If the entry is 0, the entry is not part of a VLAN. Mac Addr Displays the next-hop router’s MAC address. Port Displays the egress interface. • • • Example CP = control processor Gi = Gigabit Ethernet interface Te = 10–Gigabit Ethernet interface DellEMC# show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port --------------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Te 3/44 1.
PAGE 796
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 797
S Example (Show command output with Weighted ECMP Enabled) 100.1.1.0/24 via 10.1.1.0, weight 7 via 20.1.1.0, weight 1 DellEMC# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC RC W -----------------------------------------------------------------------------0.0.0.0/0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - 1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - 1.1.1.1/32 via 127.0.0.1 127.0.0.
PAGE 798
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information This command provides egress port information for a given IP flow.
PAGE 799
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example EXEC EXEC Privilege Version Description 9.11(0.0) Updated the command output to include the unicast reverse path forwarding (uRPF) status. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 800
ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# DellEMC#show ip interface vlan 1 Vlan 1 is down, line protocol is down Internet address is not set IP MTU is 1500 bytes Directed broadcast forwarding is disabled Proxy ARP is enabled Split Horizon is enabled Poison Reverse is disabled ICMP redirects are not sent ICMP unreachables are not sent IP unicast RPF check is not supported DellEMC# Usage Information The following describes the show ip interface brief command shown in the fo
PAGE 801
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 802
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Introduced on the C- and E-Series. 8.3.7.0 Introduced on the S4810.
PAGE 803
Example Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Regular evaluation optimization enabled/disabled added to display output. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. DellEMC# show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.3 Router Id is set to 20.20.20.
PAGE 804
routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes. all (OPTIONAL) Enter the keyword all to view both active and non-active routes. static (OPTIONAL) Enter the keyword static to view only routes the ip route command configures. summary (OPTIONAL) Enter the keyword summary. For more information, refer to the show ip route summary command.
PAGE 805
Field Description • • • • • • • • • • • • IA = OSPF inter area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes The weight for weighted ECMP route calculations is displayed for each path in the route in show ip route command.
PAGE 806
*S 0.0.0.0/0 DellEMC> Example (vrf) via 10.10.91.
PAGE 807
show ip route list Display IP routes in an IP prefix list. Syntax Parameters show ip route [vrf vrf-name] list prefix-list prefix-list Enter the name of a configured prefix list. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IP routes in an IP prefix list corresponding to that VRF. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 808
R R C Related Commands • • 2.1.2.0/24 2.1.3.0/24 2.1.4.0/24 via 2.1.4.1, Te 4/43 via 2.1.4.1, Te 4/43 Direct, Te 4/43 120/1 120/1 0/0 3d0h 3d1h 3d1h ip prefix-list — enter CONFIGURATION-IP PREFIX-LIST mode and configures a prefix list. show ip prefix-list summary — display a summary of the configured prefix lists. show ip route summary View a table summarizing the IP routes in the switch.
PAGE 809
Column Heading Description Non-active Routes Identifies the back-up routes when a route is learned by two different protocols. If the best route or active route goes down, the non-active route becomes the best route. ospf 100 If routing protocols (OSPF, RIP) are configured and routes are advertised, then information on those routes is displayed. Total 1388 active... Displays the number of active and non-active routes and the memory usage of those routes.
PAGE 810
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 F10 Monitoring MIB available for the ip traffic statistics command. pre-6.1.1.0 Introduced on the E-Series.
PAGE 811
• • • • Example ARP Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3 ARP Statistics: Sent: Request: Object = f10ArpReqSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.2 ARP Statistics: Sent: Replies: Object = f10ArpReplySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.4 ARP Statistics: Sent: Proxy: Object = f10ArpProxySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.
PAGE 812
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 6.4.1.0 Introduced Usage Information The following describes the show tcp statistics cp command shown in the following example. Field Description Rcvd: Displays the number and types of TCP packets received by the switch.
PAGE 813
Example Field Description 14 Connections closed... Displays the number of TCP connections closed, dropped. 20 Total rxmt... Displays the number of times the switch tried to re-send data and the number of connections dropped during the TCP retransmit timeout period. 0 Keepalive.... Lists the number of keepalive packets in timeout, the number keepalive probes and the number of TCP connections dropped during keepalive.
PAGE 814
26 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell EMC Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember • • • • • • • • • Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. Reference to an empty ACL permits any traffic.
PAGE 815
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 816
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 817
L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos : : : : : Current Settings(in block sizes) 2 2 4 2 3 DellEMC# Related Commands • cam-acl — configure CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 818
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Added the monitor option. permit To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP.
PAGE 819
ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 820
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for CoPP for OSPFv3 on the S4810, S4820T, S6000, and Z9000 platforms. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000 8.3.11.1 Introduced on the Z9000. 8.3.19.
PAGE 821
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.2.0 Introduced on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.8.1.
PAGE 822
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 823
27 IPv6 Basics IPv6 basic commands are supported on the Dell EMC Networking OS. NOTE: For information about the Dell EMC Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell EMC Networking OS Configuration Guide.
PAGE 824
Command History Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048–ON. 9.8(0.0P2) Introduced on the S3048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. Usage Information You can partition the LPM table to store IPv6 prefixes greater than /64 mask length.
PAGE 825
Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table. ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 826
maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have. Syntax maximum dynamic-routes—ipv6 limit {warn-threshold threshold-value | warning-only} To remove the limit on the maximum number of IPv6 routes used, use the no maximum dynamic-routesipv6 command. Parameters limit Maximum number of IPv6 routes allowed in a VRF. Valid range is from 1 to 8000 (or maximum allowable for that platform if smaller value).
PAGE 827
Usage Infomation Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.1.(0.0) Updated Usage Information section. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. • • • • • • SAA can configure up to two addresses. If any preferred prefix or valid timers time out, the corresponding address are deprecated or removed.
PAGE 828
Version Description 7.8.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. Usage Information • • • • • If two addresses are configured, delete an existing address before configuring a new address. If the last manually-configured global IPv6 address is removed using the “no” form of the command, the linklocal IPv6 address is removed automatically. IPv6 addresses on a single management interface cannot be members of the same subnet.
PAGE 829
Usage Information This command allows you to create an EUI64 address based on the specified prefix and MAC address only. Prefixes may be configured on the interface using the ipv6 nd prefix command without creating an EUI64 address.
PAGE 830
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information If the flowlabel value is already set for BGP or SSH, the system defaults to the already configured value. All packets on the same connection are considered part of the same flow by the system. For new connections, set the new flowlabel to zero. ipv6 host Assign a name and IPv6 address the host-to-IPv6 address mapping table uses.
PAGE 831
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series.
PAGE 832
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11.0.1 Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S4810, S4820, S5000, S6000, S6010–ON, S6000–ON, S6100–ON, Z9100–ON, C9010, Z9500, MXL, and FN IOM.
PAGE 833
ipv6 nd prefix Specify which IPv6 prefixes are included in Neighbor Advertisements. Syntax Parameters ipv6 nd prefix {ipv6-prefix | prefix-length | default} [no-advertise] | [noautoconfig] [no-rtr-address] [off-link] [lifetime {valid | infinite} {preferred | infinite}] ipv6-prefix Enter an IPv6 prefix. prefix-length Enter the prefix then the prefix length. The length range is from 0 to 128. default Enter the keyword default to set default parameters for all prefixes.
PAGE 834
Parameters reachable-time Enter the reachable time in milliseconds. The value is from 0 to 3600000. The default value is 0. Default Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(1.0) Introduced on the S5048F–ON. Legacy version Introduced on the S series and Z series. ipv6 route Establish a static IPv6 route.
PAGE 835
tag value (OPTIONAL) Enter the keyword tag then a tag value number. The range is from 1 to 4294967295. permanent (OPTIONAL) Enter the keyword permanent to specify that the route is not to be removed, even if the interface assigned to that route goes down. NOTE: If you disable the interface with an IPv6 address associated with the keyword permanent, the route disappears from the routing table. weight weight- Enter the keyword weight followed by a weight value. The range is from 0 to 255.
PAGE 836
A route is considered for weighted ECMP calculations only if each paths corresponding to that route is configured with a weight.
PAGE 837
show ipv6 cam stack-unit Displays the IPv6 CAM entries for the specified stack-unit. Syntax Parameters show ipv6 cam [vrf vrf-name] stack-unit unit-number port-set {0-1} [summary | index | ipv6 address] vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IPv6 CAM entries corresponding to that VRF. NOTE: If you do not specify this option, IPv6 CAM entries corresponding to the default VRF are displayed. unit-number Enter the stack unit’s ID number.
PAGE 838
show ipv6 control-plane icmp Displays the status of the icmp control-plane setting for the error eate limit setting. Syntax show ipv6 control-plane icmp Default 100 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant DellEMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 839
Version Description 8.4.2.1 Introduced on the S-Series. Usage Information Host tables are not stored in CAM tables on S-Series platforms. Entries for camIndex displays as zero (0) on the show ipv6 fib stack-unit output for neighbor entries, such as address resolution protocol (ARP) entries. show ipv6 flowlabel-zero Display the flow label zero setting. Syntax show ipv6 flowlabel-zero Default Disabled Command Modes EXEC Command History This guide is platform-specific.
PAGE 840
loopback (OPTIONAL) View information for IPv6 Loopback interfaces. port-channel (OPTIONAL) View information for IPv6 port channels. tengigabitetherne t (OPTIONAL) View information for an IPv6 tengigabitethernet interface. fortyGigE (OPTIONAL) View information for an IPv6 fortygigabitethernet interface. stack-unit id (OPTIONAL) View information for stacking. tunnel tunnel-id (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs.
PAGE 841
DAD is enabled, number of DAD attempts: 3 ND reachable time is 39610 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 IPv6 unicast RPF check is not supported DellEMC# DellEMC# show ipv6 interface port-channel 128 Port-channe
PAGE 842
Link Local address: fe80::201:e8ff:fea7:497e Global Unicast address(es): Actual address is 300::1, subnet is 300::/64 (MANUAL) Remaining lifetime: infinite Virtual-IP IPv6 address is not set Global Anycast address(es): Joined Group address(es): ff02::1 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds ND retransmit interval is 1000 milliseconds ND hop limit is
PAGE 843
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 844
hostname (OPTIONAL) View information for this IPv6 routes with Host Name. all (OPTIONAL) View information for all IPv6 routes. bgp (OPTIONAL) View information for all IPv6 BGP routes. connected (OPTIONAL) View only the directly connected IPv6 routes. isis (OPTIONAL) View information for all IPv6 IS-IS routes. list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes.
PAGE 845
Field Description • • • • • • • • • • • • • • Example (SSeries) LO = Locally Originated O = OSPF IA = OSPF inter-area N1 = OSPF NSSA external type 1 N2 = OSPF NSSA external type 2 E1 = OSPF external type 1 E2 = OSPF external type 2 i = IS-IS L1 = IS-IS level-1 L2 = IS-IS level-2 IA = IS-IS inter-area * = candidate default > = non-active route + = summary routes Destination Identifies the route’s destination IPv6 address.
PAGE 846
trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults None Command Modes CONFIGURATION-POLICY-MAP-IN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.
PAGE 847
28 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on Dell EMC Networking OS platforms. To configure and verify the iSCSI optimization feature, use the following Dell EMC Networking OS commands.
PAGE 848
To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. Defaults 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.
PAGE 849
Version Description 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. Usage Information By default, iSCSI flows are assigned to dot1p priority 4. iscsi enable Globally enable iSCSI optimization.
PAGE 850
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. iscsi profile-compellant Configure the auto-detection of Dell Compellent arrays on a port.
PAGE 851
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. Usage Information You can configure up to 16 target TCP ports on the switch in one command or multiple commands.
PAGE 852
show iscsi session Display information about active iSCSI sessions on the switch. Syntax show iscsi session Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 853
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 854
Related Commands 854 Version Description 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. • • • show iscsi — display the currently configured iSCSI settings. show iscsi session — display detailed information about active iSCSI sessions on the switch. show iscsi session detailed — display detailed information on active iSCSI sessions on the switch.
PAGE 855
29 Intermediate System to Intermediate System (IS-IS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 856
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • isis ipv6 metric isis metric isis network point-to-point isis password isis priority is-type log-adjacency-changes lsp-gen-interval lsp-mtu lsp-refresh-interval max-area-addresses max-lsp-lifetime maximum-paths metric-style multi-topology net passive-interface redistribute redistribute bgp redistribute ospf router isis set-overload-bit show config show isis database show isis graceful-restart detail show isis hostname show isis interface show is
PAGE 857
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabled by default.
PAGE 858
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced Usage Information You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1. However, you can regulate the rate flow from one level to another using an IP Prefix list.
PAGE 859
Usage Information To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands • • domain-password — set the authentication password for a routing domain. isis password — configure an authentication password for an interface.
PAGE 860
database Clears IS-IS LSP database information. traffic Clears IS-IS counters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 861
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information To configure a shortcut name that you can use instead of entering a long string of numbers associated with an NSAP address, use this command. Related Commands • hostname dynamic — enable dynamic learning of host names from routers in the domain and allows the routers to advertise the host names in LSPs. debug isis Enable debugging for all IS-IS operations.
PAGE 862
Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details. interface (OPTIONAL) Identifies the interface type and the interface information: • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 863
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 864
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 865
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. debug isis update-packets Enable debugging on link state PDUs (LSPs) that a router detects. Syntax debug isis [vrf vrf-name] update-packets [interface] To turn off debugging, use the no debug isis update-packets [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS.
PAGE 866
default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information. Syntax default-information originate [always] [metric metric] [route-map map-name] To disable the generation of a default route into the specified IS-IS routing domain, use the no defaultinformation originate [always] [metric metric] [route-map map-name] command. Parameters always (OPTIONAL) Enter the keyword always to have the default route always advertised.
PAGE 867
description Enter a description of the IS-IS routing protocol. Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the IS-IS protocol (80 characters maximum). Defaults None Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 868
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 869
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.
PAGE 870
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced.
PAGE 871
Version Description 6.3.1.0 Introduced. Usage Information When you execute this command, IS-IS does not download the route to the routing table if the same route was redistributed into IS-IS routing protocol on the same router. domain-password Set the authentication password for a routing domain. Syntax domain-password [hmac-md5 | encryption-type] password To disable the password, use the no domain-password command.
PAGE 872
graceful-restart ietf Enable graceful restart on an IS-IS router. Syntax graceful-restart ietf To return to the default, use the no graceful-restart ietf command. Parameters ietf Enter ietf to enable graceful restart on the IS-IS router. Defaults Graceful restart disabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 873
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 874
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. • graceful-restart t3 — configure the overall wait time before graceful restart completes. graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated.
PAGE 875
graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize. Syntax graceful-restart t2 {level-1 | level-2} seconds To return to the default, use the no graceful-restart t2 command. Parameters level-1, level-2 Enter the keywords level-1 or level-2 to identify the database instance type to which the wait interval applies. seconds Enter the gracefule-restart t2 time in seconds.
PAGE 876
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 877
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information IS-IS hellos are padded to the full maximum transmission unit (MTU) size.
PAGE 878
Related Commands • clns host — define a name-to-NSAP mapping. ignore-lsp-errors Ignore LSPs with bad checksums instead of purging those LSPs. Syntax ignore-lsp-errors To return to the default values, use the no ignore-lsp-errors command. Defaults In IS-IS, the default deletes LSPs with internal checksum errors (no ignore-lsp-errors). Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 879
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 880
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information Configure a network entity title (the net command) to specify the area address and the router system ID.
PAGE 881
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Because the default establishes Level 1 and Level 2 adjacencies, you do not need to configure this command. Routers in an IS-IS system must be configured as a Level 1-only, Level 1-2, or Level 2-only system.
PAGE 882
Usage Information The default values of this command are typically satisfactory transmission times for a specific interface on a designated intermediate system. To maintain database synchronization, the designated routers send CSNPs. You can configure Level 1 and Level 2 CSNP intervals independently. isis hello-interval Specify the length of time between hello packets sent.
PAGE 883
To return to the default values, use the no isis hello-multiplier [multiplier] [level-1 | level-2] command. Parameters multiplier Specifies an integer that sets the multiplier for the hello holding time. Never configure a hello-multiplier lower than the default (3). The range is from 3 to 1000. The default is 3. level-1 (OPTIONAL) Select this value to configure the hello multiplier independently for Level 1 adjacencies. This value is the default.
PAGE 884
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 885
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Usage Information Dell EMC Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics.
PAGE 886
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Dell EMC Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics.
PAGE 887
hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password. level-1 (OPTIONAL) Independently configures the authentication password for Level 1. The router acts as a station router for Level 1 routing. This setting is the default. level-2 (OPTIONAL) Independently configures the authentication password for Level 2. The router acts as an area router for Level 2 routing. Defaults No default password.
PAGE 888
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 889
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information The IS-IS protocol automatically determines area boundaries and are able to keep Level 1 and Level 2 routing separate.
PAGE 890
lsp-gen-interval Set the minimum interval between successive generations of link-state packets (LSPs). Syntax lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no lsp-gen-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters level-l (OPTIONAL) Enter the keywords level-1 to apply the configuration to generation of Level-1 LSPs.
PAGE 891
lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 512 to 16000 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497. NOTE: The appropriate interface circuit is brought down and removed. Defaults 1497 bytes.
PAGE 892
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 893
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. Usage Information To configure the number of area addresses on router, use this command.
PAGE 894
Usage Information Change the maximum LSP lifetime with this command. The maximum LSP lifetime must always be greater than the LSP refresh interval. The seconds parameter enables the router to keep LSPs for the specified length of time. If the value is higher, the overhead is reduced on slower-speed links. Related Commands • lsp-refresh-interval — set the link-state packet (LSP) refresh interval. maximum-paths Allows you to configure the maximum number of equal cost paths allowed in a routing table.
PAGE 895
To return to the default values, use the no metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] command. Parameters narrow Allows you to generate and accept old-style TLVs. The metric range is from 0 to 63. transition Allows you to generate both old-style and new-style TLVs. The metric range is from 0 to 63. wide Allows you to generate and accept only new-style TLVs. The metric range is from 0 to 16777215. level-1 Enables the metric style on Level 1.
PAGE 896
Defaults Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 897
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command.
PAGE 898
redistribute Redistribute routes from one routing domain to another routing domain. Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] To end redistribution or disable any of the specified keywords, use the no redistribute {static | connected | rip} [metric metric-value] [metric-type {external | internal}] [level-1 | level-1-2 | level-2] [route-map map-name] command.
PAGE 899
Version Description 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. Usage Information To redistribute a default route (0.0.0.0/0), configure the default-information originate command. Changing or disabling a keyword in this command does not affect the state of the other command keywords. When an LSP with an internal metric is received, the Dell EMC Networking OS considers the route cost while considering the advertised cost to reach the destination.
PAGE 900
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 901
• • external internal level-1 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 1 routes. level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level-1-2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes. This setting is the default. match {external | internal} (OPTIONAL) The command used for OSPF to route and redistribute into other routing domains.
PAGE 902
router isis Allows you to enable the IS-IS routing protocol and to specify an IP IS-IS process. Syntax router isis [vrf vrf-name] [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to enable the IS-IS routing protocol and to specify an IP IS-IS process on that VRF. tag (OPTIONAL) This is a unique name for a routing process. A null tag is assumed if the tag option is not specified.
PAGE 903
Defaults Not set. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. ROUTER ISIS (for IPv4) CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 904
Example (RouterIsis) Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode. DellEMC(conf-router_isis)# show config ! router isis clns host ISIS 49.0000.0001.F100.E120.0013.
PAGE 905
summary (OPTIONAL) Displays the summary of link-state database information when specified. lspid (OPTIONAL) Display only the specified LSP. system-id (OPTIONAL) Displays the link-state database for system-id. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 906
Example Field Description ATT This value represents the Attach bit. This value indicates that the router is a Level 1-2 router and can reach other areas. Level 1-only routers and Level 1-2 routers that have lost connection to other Level 1-2 routers use the Attach bit to find the closest Level 1-2 router. They install a default route to the closest Level 1-2 router. P This value represents the P bit. This bit is always set to zero as Dell EMC Networking does not support area partition repair.
PAGE 907
NLPID: 0xCC Area Address: 49.0000.0001 show isis graceful-restart detail Display detailed IS-IS graceful restart related settings. Syntax show isis [vrf vrf-name] graceful-restart detail Command Modes • • Parameters Command History Example EXEC EXEC Privilege vrf vrf-name (Optional) Enter the keyword vrf followed by the name if the VRf to display IS-IS graceful restart details corresponding to that VRF.
PAGE 908
Suppress Adj rcv count : 0 (level-1), 0 (level-2) Restart CSNP rcv count : 0 (level-1), 0 (level-2) Database Sync count : 0 (level-1), 0 (level-2) show isis hostname Display IS-IS host names configured or learned on the switch. Syntax show isis [vrf vrf-name] hostname Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IS-IS host names corresponding to that VRF. Command Modes • • Command History This guide is platform-specific.
PAGE 909
• • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a port channel interface, enter the keywords port-channel then a number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 910
show isis neighbors Display information about neighboring (adjacent) routers. Syntax show isis [vrf vrf-name] neighbors [level-1 | level-2] [detail] [interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display adjacent router information corresponding to that VRF. level-1 (OPTIONAL) Displays information about Level 1 IS-IS neighbors. level-2 (OPTIONAL) Displays information about Level 2 IS-IS neighbors.
PAGE 911
Example Field Description Type This value displays the adjacency type (Layer 2, Layer 2 or both). Priority IS-IS priority the neighbor advertises. The neighbor with highest priority becomes the designated router for the interface. Uptime Displays the interfaces uptime. Circuit Id The neighbor’s interpretation of the designated router for the interface. The bold sections below identify that Multi-Topology IS-IS is enabled. This command displays only one IP address per line.
PAGE 912
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The bold section identifies that Multi-Topology IS-IS is enabled. DellEMC# show isis protocol IS-IS Router: System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.0000.0001 Routing for area address(es): 49.0000.
PAGE 913
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information The following describes the show isis traffic command shown in the following example.
PAGE 914
IS-IS: IS-IS: IS-IS: IS-IS: IS-IS: DellEMC# Level-2 DR Elections : 4 Level-1 SPF Calculations : 0 Level-2 SPF Calculations : 389 LSP checksum errors received : 0 LSP authentication failures : 0 spf-interval Specify the minimum interval between shortest path first (SPF) calculations.
PAGE 915
Usage Information This command spf-interval in CONFIG-ROUTER-ISIS-AF-IPV6 mode is used for IPv6 Multi-Topology route computation only. If using Single Topology mode, use the spf-interval command in CONFIG-ROUTER-ISIS mode for both IPv4 and IPv6 route computations. SPF throttling slows down the frequency at which route calculations are performed during network instability.
PAGE 916
30 Link Aggregation Control Protocol (LACP) This section contains commands for Dell EMC Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell EMC Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 917
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • show lacp — display the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 918
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 919
lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority. Syntax lacp port-priority priority-value To return to the default setting, use the no lacp port-priority priority-value command. Parameters priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768.
PAGE 920
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 921
Related Commands • • show lacp — display the LACP information. show interfaces port-channel — display information on configured Port Channel groups. show lacp Display the LACP matrix. Syntax Parameters show lacp port-channel-number [sys-id | counters] port-channelnumber Enter a port-channel number. The range is from 1 to 128. sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters.
PAGE 922
Distribution disabled, M-Partner Defaulted, N-Partner Non-defaulted, O-Receiver is in expired state, P-Receiver is not in expired state Port Te 1/6 is enabled, LACP is Actor Admin: State ACEHJLMP Oper: State ACEGIKNP Partner Admin: State BDFHJLMP Oper: State BCEGIKNP DellEMC# Example (Sys-id) enabled and mode is lacp Key 1 Priority 128 Key 1 Priority 128 Key 0 Priority 0 Key 1 Priority 128 DellEMC# show lacp 1 sys-id Actor System ID: Priority 32768, Address 0001.e800.
PAGE 923
31 Layer 2 MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically. Syntax Parameters clear mac-address-table {dynamic | sticky }{address mac-address | all | interface interface | vlan vlan-id} dynamic Enter the keyword dynamic to specify dynamically-learned MAC addresses. sticky Enter the keyword sticky to specify sticky MAC addresses.
PAGE 924
mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table. Syntax mac-address-table aging-time seconds Parameters seconds Enter either zero (0) or a number as the number of seconds before MAC addresses are relearned. To disable aging of the MAC address table, enter 0. The range is from 10 to 1000000. The default is 1800 seconds. Defaults 1800 seconds Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 925
multicast Enter a vlan port to where L2 multicast MAC traffic is forwarded. NOTE: Use this option if you want multicast functionality in an L2 VLAN without IGMP protocols.
PAGE 926
mac-address-table station-move threshold Change the frequency with which the MAC address station-move trap is sent after a MAC address changes in a VLAN. A trap is sent if a station move is detected above a threshold number of times in a given interval. Syntax [no] mac-address-table station-move threshold number interval count Parameters threshold number Enter the keyword threshold then the number of times MAC addresses in VLANs can change before an SNMP trap is sent. The range is from 1 to 10.
PAGE 927
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Usage Information For more information about using this command, see NIC Teaming in the Layer 2 section of the Dell EMC Networking OS Configuration Guide.
PAGE 928
Version Description 8.3.12.0 Deprecated the no-station-move command (replaced by the mac-learninglimit mac-address-sticky command). 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added the station-move option. 6.5.1.0 Added support for MAC Learning-Limit on the LAG. Usage Information This command and its options are supported on physical interfaces, static LAGs, LACP LAGs, and VLANs.
PAGE 929
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.
PAGE 930
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information If you configure mac-learn-limit and the sticky MAC feature is enabled, dynamically learned MAC addresses are converted to sticky for that port. Any new MAC address that is learned also becomes sticky for that port. Related Commands • show mac learning-limit — display the details of the mac learning-limit.
PAGE 931
Version Description 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands • show mac learning-limit — display details of the mac learning-limit. mac learning-limit reset Reset the MAC address learning-limit error-disabled state.
PAGE 932
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the C9010, MXL, FN IOM, S3100 series, S4810, S4820T, S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, and Z9500.
PAGE 933
show cam mac linecard (dynamic or static) Display the CAM size and the portions allocated for MAC addresses and for MAC ACLs. Syntax Parameters show cam mac linecard slot port-set port-pipe [address mac_addr | dynamic | interface interface | static | vlan vlan-id] linecard slot (REQUIRED) Enter the keyword linecard then a slot number to select the linecard for which to gather information.
PAGE 934
102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 Dell# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 01:80:00:00:00:00 01:00:0c:cc:cc:cc 01:80:c2:00:00:02 01:80:c2:00:00:0e 00:01:e8:0d:b7:68 00:01:e8:0d:b7:67 00:01:e8:0d:b7:66 00:01:e8:0d:b7:65 00:01:e8:0d:b7:64 00:01:e8:0d:b7:63 00:01:e8:0d:b7:62 00:01:e8:0d:b7:61 00:01:e8:0d:b7:60 00:01:e8:0d:b7:5f 00:01:e8:0d:b7:5e 00:01:e8:0d:b7:5d SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SYSTEM_STATIC SY
PAGE 935
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 936
Line Beginning Description With Dynamic Address... Lists the number of dynamically learned MAC addresses. Static Address... Lists the number of user-defined MAC addresses. Total MAC... Lists the total number of MAC addresses the switch uses.
PAGE 937
Version Description pre-6.2.1.1 Introduced on the E-Series. Example DellEMC# show mac-address-table aging-time Mac-address-table aging time : 1800 DellEMC# Related Commands • show mac-address-table — display the current MAC address configuration. show mac accounting destination Display destination counters for Layer 2 traffic (available on physical interfaces only).
PAGE 938
00:44:00:00:00:02 00:44:00:00:00:01 00:22:00:00:00:00 00:44:00:00:00:02 00:44:00:00:00:01 Te Te Te Te Te 11/1 11/1 11/1 11/1 11/1 1000 1000 1000 2000 2000 10000 10000 10000 10000 10000 5120000 5120000 5120000 5120000 5120000 Dell-1# Related Commands • show mac accounting access-list — display the MAC access list configurations and counters (if configured). show mac learning-limit Display MAC address learning limits set for various interfaces.
PAGE 939
Example Version Description 7.5.1.0 Added support for the violate-action and detail options. 6.5.1.0 Added support for Port Channel.
PAGE 940
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information To return VLAN 1 as the Default VLAN, use this command syntax (default-vlan-id 1). The Default VLAN contains only untagged interfaces.
PAGE 941
name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters vlan-name Enter up to 32 characters as the name of the VLAN. Defaults Not configured. Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 942
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 943
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Updated to support OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 944
Column Heading Description • • • Example Po = port channel Te = ten-gigabit Ethernet Fo = forty-gigabit Ethernet DellEMC# show vlan Codes: * - Default VLAN, G - GVRP VLANs, P - Primary, C - Community, I Isolated Q: U - Untagged, T - Tagged, O - Openflow x - Dot1x untagged, X - Dot1x tagged o - OpenFlow untagged, O - OpenFlow tagged G - GVRP tagged, M - Vlan-stack i - Internal untagged, I - Internal tagged, v - VLT untagged, V - VLT tagged NUM Status Description Q Ports * 1 Inactive 2 Active U Po1(Te 1/1
PAGE 945
x - Dot1x untagged, X - Dot1x tagged G - GVRP tagged, M - Vlan-stack NUM 42 DellEMC# Example (Brief) Status Description Q Ports Active U Te 1/47 DellEMC# show vlan br VLAN Name STG MAC Aging IP Address ---- -----------------------------------1 0 1800 unassigned 2 0 1800 2.2.2.2/24 3 0 1800 3.3.3.
PAGE 946
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 947
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 948
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 949
• • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 950
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 951
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. Related Commands • • fefd reset — clear an interface in Err-disabled state. It doesn’t work until the interface is in err-disabled state. fefd mode — change FEFD mode on an interface.
PAGE 952
fefd mode Change the FEFD mode on an interface. Syntax fefd mode {normal | aggressive}] To return the FEFD mode to the default of normal, use the no fefd mode command. Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol.
PAGE 953
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 954
Version Description 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands • • fefd — enable far-end failure detection. fefd-global — enable FEFD globally on the system. fefd-global Enable FEFD globally on the system. Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command.
PAGE 955
Version Description Legacy E-Series command. Usage Information If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. Related Commands • • • fefd — enable far-end failure detection. fefd-global interval — configure an interval between FEFD control packets. show fefd — display the FEFD command output.
PAGE 956
Field Description Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets. State Displays the state of the interface and can be one of the following: • • • • • Example bi-directional (interface is up, connected and hearing neighbor’s echoes). err-disabled (only found when FEFD mode is aggressive and when the interface has not hearing its neighbor’s echoes for three times the message interval.
PAGE 957
32 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell EMC Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 958
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. • • • protocol lldp (Configuration) — enable LLDP globally.
PAGE 959
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise interface-port-desc Advertise port descriptor. Syntax advertise interface-port-desc {description | port-id} To remove the advertised port descriptor, use the no advertise interface—port—desc {description | port-id} command. Parameters description Enter the keyword description then the interface description. port-id Enter the keyword port-id then the port-id. The range is from 0 to 7.
PAGE 960
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Modified to support management-address parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 961
clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface. Syntax Parameters clear lldp counters [interface interface] interface interface (OPTIONAL) Enter the following keywords and the interface information: • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information.
PAGE 962
Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 963
rx Enter the keyword rx to display receive-only packet information. both Enter the keyword both to display both receive and transmit packet information. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.13.0.0 Enhanced to display organizational specific unrecognized LLDP TLVs. 9.11.2.
PAGE 964
disable Enable or disable LLDP. Syntax disable To enable LLDP, use the no disable command. Defaults Enabled — no disable. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.
PAGE 965
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 966
Parameters tx Enter the keyword tx to set the mode to transmit. rx Enter the keyword rx to set the mode to receive. Defaults Both transmit and receive. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 967
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.
PAGE 968
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 969
• • detail For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. (OPTIONAL) Enter the keyword detail to display all the TLV information, remote management IP addresses, timers, and LLDP tx and rx counters. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 970
Next packet will be sent after 9 seconds The neighbors are given below: ----------------------------------------------------------------------Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 00:00:00:00:00:01 Remote Port Subtype: Interface name (5) Remote Port ID: TenGigabitEthernEt 1/40 Local Port ID: TenGigabitEthernet 1/1 Locally assigned remote Neighbor Index: 1 Remote TTL: 120 Information valid for next 44 seconds Time since last information change of this neighbor: 00:01:16 UnknownTLVList
PAGE 971
Remote Chassis ID: 4c:76:25:f4:ab:03 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: TenGigabitEthernet 1/2 Locally assigned remote Neighbor Index: 3 Remote TTL: 300 Information valid for next 199 seconds Time since last information change of this neighbor: 00:01:41 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),123, 4) ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),120, 4) ((00-01-66),
PAGE 972
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(2.5) Enhanced to display total number of suppressed traps on the, S3048–ON, S4048-ON, S4048T-ON, S6010–ON and Z9100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 973
show running-config lldp Display the current global LLDP configuration. Syntax show running-config lldp Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.
PAGE 974
Usage Information SNMP notification for the changes in the lldp remote entry table is throttled by 5 seconds (default), or the configured time set using this command. If more than one notification message is generated within the configured time, only the first one will be sent and the remaining messages are suppressed. LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands. Dell EMC Networking OS LLDP-MED commands are an extension of the set of LLDP TLV advertisement commands.
PAGE 975
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. • • • protocol lldp (Configuration) — enable LLDP globally. debug lldp interface — debug LLDP. show lldp neighbors — display the LLDP neighbors.
PAGE 976
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. • • debug lldp interface — debug LLDP. show lldp neighbors — display the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system.
PAGE 977
Version Description 7.6.1.0 Introduced on the C-Series and E-Series. Usage Information • • Related Commands • • ECS — Emergency call service such as defined by TIA or the national emergency numbering association (NENA) ELIN — Emergency location identification number, a valid North America Numbering Plan format telephone number supplied for ECS purposes. debug lldp interface — debug LLDP. show lldp neighbors — display the LLDP neighbors.
PAGE 978
advertise med softphone-voice To advertise softphone to enable IP telephony on a computer so that the computer can be used as a phone, configure the system. Syntax advertise med softphone-voice {vlan-id layer2_priority DSCP_value} | {prioritytagged number} To return to the default, use the no advertise med softphone-voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 979
To return to the default, use the no advertise med streaming-video {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094. layer2_priority Enter the Layer 2 priority. The range is from 0 to 7. DSCP_value Enter the DSCP value. The range is from 0 to 63. priority-tagged Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. number Defaults Unconfigured.
PAGE 980
priority-tagged number Enter the keywords priority-tagged, the Layer 2 priority, and then the DSCP value. Defaults Unconfigured. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 981
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 982
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. • • debug lldp interface — de bug LLDP.
PAGE 983
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. • • debug lldp interface — debug LLDP. show lldp neighbors — display the LLDP neighbors.
PAGE 984
33 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 985
Related Commands • • clear arp-cache — clear dynamic ARP entries from the ARP table. show arp — display the ARP table. mac-address-table static (for Multicast MAC Address) For multicast mode of network load balancing (NLB), configure a static multicast MAC address, associate the multicast MAC address with the VLAN used to switch Layer 2 multicast traffic, and add output ports that will receive multicast streams on the VLAN.
PAGE 986
Example (Multicast) Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for multicast MAC address on the MXL platform. mac-address-table static 01:00:5E:01:00:01 {multicast vlan 2 output—range Te 1/2,Te 1/3 ip vlan-flooding Enable unicast data traffic flooding on VLAN member ports.
PAGE 987
34 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell EMC Networking OS supports MSDP commands on the S4048–ON platform.
PAGE 988
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries.
PAGE 989
Version Description 6.2.1.1 Introduced clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters clear ip msdp statistic peer peer-address peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer. Defaults Without any options, this command clears the entire source-active cache.
PAGE 990
packet peer address pim Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.). Enter the keyword pim to debug advertisement from PIM. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 991
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.4.1.0 Introduced • show ip msdp sa-cache rejected-sa — display the rejected SAs in the SA cache. ip msdp default-peer Define a default peer from which to accept all source-active (SA) messages. Syntax ip msdp default-peer peer address [list name] To remove the default peer, use the no ip msdp default-peer {peer address} list name command.
PAGE 992
ip msdp log-adjacency-changes Enable logging of MSDP adjacency changes. Syntax ip msdp log-adjacency-changes To disable logging, use the no ip msdp log-adjacency-changes command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 993
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.
PAGE 994
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 6.2.1.
PAGE 995
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series.
PAGE 996
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced Usage Information Modifications to the ACL do not have an immediate effect on the sa-cache.
PAGE 997
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the E-Series. ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache. The range is from 1 to 500000.
PAGE 998
ip msdp shutdown Administratively shut down a configured MSDP peer. Syntax ip msdp shutdown {peer address} Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 999
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced show ip msdp Display the MSDP peer status, SA cache, or peer summary.
PAGE 1000
Example DellEMC# show ip msdp peer 100.1.1.1 Peer Addr: 100.1.1.1 Local Addr: 100.1.1.2(639) Connect Source: none State: Established Up/Down Time: 00:00:08 Timers: KeepAlive 60 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: none Output (S,G) filter: none DellEMC# Example (Sacache) DellEMC# show ip msdp sa-cache MSDP Source-Active Cache - 1 entries GroupAddr SourceAddr RPAddr 224.1.1.1 172.21.220.10 172.21.3.
PAGE 1001
Example Version Description 8.3.7.1 Introduced on the S4810. 7.4.1.0 Introduced. DellEMC# show ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 200 rejected SAs received, cache-size 1000 UpTime GroupAddr SourceAddr RPAddr LearnedFrom Reason 00:00:13 225.1.2.1 10.1.1.3 110.1.1.1 13.1.1.2 Rpf-Fail 00:00:13 225.1.2.2 10.1.1.4 110.1.1.1 13.1.1.2 Rpf-Fail 00:00:13 225.1.2.3 10.1.1.3 110.1.1.1 13.1.1.2 Rpf-Fail 00:00:13 225.1.2.4 10.1.1.4 110.1.1.1 13.1.1.2 Rpf-Fail 00:00:13 225.1.2.5 10.1.1.3 110.1.1.
PAGE 1002
35 Multicast Listener Discovery Protocol The Multicast Listener Discovery (MLD) protocol is used by IPv6 routers to discover multicast listeners on a directly attached link. Similar to the Internet Group Management Protocol (IGMP), which handles multicast group memberships in IPv4 networks, MLD is used for multicast management on IPv6 networks.
PAGE 1003
debug ipv6 mld Enable debugging on IPv6 MLD packets. Syntax debug ipv6 mld [vrf vrf-name] {group-address | interface} To turn off debugging, use the no debug ipv6 mld {group-address | interface} command. Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF. group-address (OPTIONAL) Enter the multicast group address in the x:x:x:x::x format. The :: notation specifies successive hexadecimal fields of zero.
PAGE 1004
To return to the default, use the no ipv6 mld last-member-query-interval {milliseconds} command. Parameters milliseconds Enter the last member query interval in milliseconds. The range is from 100 to 65535. Defaults 1000 milliseconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(3.
PAGE 1005
ipv6 mld version Configure the MLD version on the system. Syntax ipv6 mld version {1 | 2} Defaults MLD version 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F–ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 1006
Example Dell#show ipv6 mld groups Total Number of Groups: 1 MLD Connected Group Membership Group Address Interface Mode Ff08::12 Vlan 10 MLDv2 Uptime 00:00:12 Expires 00:02:05 Last Reporter 1::2 show ipv6 mld interface View the configured MLD interfaces. Syntax show ipv6 mld [vrf vrf-name] interface [interface] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF.
PAGE 1007
clear ipv6 mld snooping groups Clear entries from the group cache table. Syntax Parameters clear ipv6 mld snooping groups [interface | group-address] interface Enter the following keywords and slot/port or number information: • • • • • group-address For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/port information. For a Port Channel interface, enter the keywords port-channel then a number.
PAGE 1008
Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping Enable MLD snooping on a VLAN. Syntax ipv6 mld snooping To disable MLD snooping, use the no ipv6 mld snooping command. Defaults Enabled on all VLAN interfaces. Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 1009
Version Description 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010. ipv6 mld snooping mrouter Configure a Layer 2 port as a multicast router port. Syntax Parameters ipv6 mld snooping mrouter interface {interface interface} interface Enter the keyword interfaceto indicate the next-hop interface to the multicast router.
PAGE 1010
show ipv6 mld snooping groups Display the IPv6 MLD snooping group information. Syntax show ipv6 mld snooping groups [group address] [summary] [interface interface [detail]] Parameters group-address (Optional) Enter the multicast group addresss in the X:X:X:X::X format. The :: notation specifies successive hexadecimal fields of zero. summary (OPTIONAL) Enter the keyword summary to display a summary of groups.
PAGE 1011
Example Version Description 9.14(1.0) Updated the output to show both MLD versions 1 and 2. 9.14(0.0) Introduced on the S3048–ON, S4048–ON, S4048T-ON, S5048F-ON, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, S3100, and C9010.
PAGE 1012
36 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell EMC Networking OS, conforms to IEEE 802.1s. This command supports the Dell EMC Networking OS.
PAGE 1013
Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1014
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. • protocol spanning-tree mstp — enter MULTIPLE SPANNING TREE mode.
PAGE 1015
Related Commands Version Description 6.5.1.0 Introduced. • • max-age — change the wait time before MSTP refreshes protocol configuration information. hello-time — change the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command.
PAGE 1016
max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell EMC Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds. Defaults 20 seconds Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific.
PAGE 1017
vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094. bridge-priority Enter the keywords bridge-priority then a value in increments of 4096 as the bridge priority. The range is from zero (0) to 61440. priority Valid priority values are: 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, and 61440. All other values are rejected. Defaults default bridge-priority is 32768.
PAGE 1018
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1019
Example DELLEMC(conf)#protocol spanning-tree pvst DELLEMC(conf-pvst)#port-channel path-cost custom protocol spanning-tree mstp To enable and configure the multiple spanning tree group, enter MULTIPLE SPANNING TREE mode. Syntax protocol spanning-tree mstp To disable the multiple spanning tree group, use the no protocol spanning-tree mstp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1020
To return to the default values, use the no revision command. Parameters range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. Defaults 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1021
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series.
PAGE 1022
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information Enable the multiple spanning tree protocol prior to using this command.
PAGE 1023
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) loopback BPDU inconsistency causes. Usage Information Enable the multiple spanning tree protocol prior to using this command. Example DellEMC# show spanning-tree msti 10 MSTI 10 VLANs mapped 101-105 Bridge Identifier has priority 32768, Address 0001.e802.
PAGE 1024
DellEMC# show spanning-tree msti 0 MSTI 0 VLANs mapped 1-4094 Root Identifier has priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15, max hops 20 Bridge Identifier has priority 32768, Address 0001.e801.6aa8 Configured hello time 2, max age 20, forward delay 15, max hops 20 We are the root of MSTI 0 (CIST) Current root has priority 32768, Address 0001.e801.6aa8 CIST regional root ID Priority 32768, Address 0001.e801.
PAGE 1025
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1026
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1027
Version Description 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced Usage Information By default, Dell EMC Networking OS implements an optimized flush mechanism for MSTP. This mechanism helps in flushing the MAC addresses only when necessary (and less often) allowing for faster convergence during topology changes. However, if a standards-based flush mechanism is needed, this knob command can be turned on to enable flushing MAC addresses after receiving every topology change notification.
PAGE 1028
37 Multicast The multicast commands are supported by Dell EMC Networking OS. Topics: • • IPv4 Multicast Commands IPv6 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1029
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 1030
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 1031
Version Description 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Usage Information This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile. To store multicast routes, use the IN-L3-McastFib CAM partition.
PAGE 1032
Related Commands • ip pim sparse-mode — enable IGMP and PIM on an interface. mtrace Trace a multicast route from the source to the receiver. Syntax mtrace [vrf vrf-name] {source-address/hostname} [destination-address/hostname] [group-address/hostname] Parameters Command Modes Command History vrf vrf-name Enter the keyword vrf followed by the name of the VRF. If VRF name is not mentioned, the default VRF will be used. Mtrace is not supported for management VRF.
PAGE 1033
The mtrace command traverses the path of the response data block in the reverse direction of the multicast data traffic. The mtrace command traverses the reverse path to the source from the destination. As a result, the tabular output of the mtrace command displays the destination details in the first row, followed by the RPF router details along the path in the consequent rows, and finally the source details in the last row.
PAGE 1034
0 1/10, 0 1/11, 224.1.1.2 0.0.0.0 1000 1 gi 1/3, gi 224.1.1.1 165.13.34.5 2000 2 gi 1/5, gi show ip mroute View the multicast routing table. Syntax show ip mroute [vrf vrf-name] [static | group-address [source-address] | count | snooping [vlan vlan-id] [group-address [source-address]] | summary | vlt [group-address [source-address] | count] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 1035
Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1036
Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 1037
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources. If a PIMregistered multicast source is reachable using static mroute as well as unicast route, the distance of each route is examined and the route with shorter distance is the one the PIM selects for reach-ability.
PAGE 1038
To disable multicast forwarding, use the no ipv6 multicast-routing [vrf vrf-name] command. Defaults Parameters Disabled. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable IP multicast forwarding on that VRF. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 9.11.3.
PAGE 1039
(*, ff0e:225:0:1::1), uptime 18:01:56 Incoming interface: Null Outgoing interface list: Vlan 401 Vlan 1001 (2001:120:3:1::11, ff0e:225:0:1::1), uptime 18:02:03 Incoming interface: Vlan 401 Outgoing interface list: Vlan 1001 (2001:130:3:1::11, ff0e:225:0:1::1), uptime 18:01:17 Incoming interface: Vlan 1001 Outgoing interface list: Vlan 401 (2001:140:3:1::11, ff0e:225:0:1::1), uptime 18:01:13 Incoming interface: Vlan 1001 Outgoing interface list: Vlan 401 Dell# show ipv6 multicast-cam Display the content add
PAGE 1040
show ipv6 rpf View reverse path forwarding. Syntax show ipv6 rpf Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.11.3.0 Introduced on the C9000, S3048–ON, S3100, S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON and Z9100–ON.
PAGE 1041
38 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1042
• • For a port channel interface, enter the keywords port-channel then a number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1043
• For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. hardware_address Enter a 48-bit hardware MAC address in nn:nn:nn:nn:nn:nn format. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1044
NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero. interface interface Enter the keyword interface then the interface type and slot/port or number information: • • • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1045
IPv6 Router Advertisement (RA) Guard The IPv6 RA guard provides support to perform conditional forwarding or blocking of the router advertisement messages that are received at the network device platform. This functionality analyzes and filters the RAs sent by the devices and compares the configuration information on the layer 2 device with the RA frame. Once the layer 2 device validates the content of the RA frame against the configuration, it forwards the RA to its unicast or multicast destination.
PAGE 1046
device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command. Parameters host Enter the keyword host to set the device-role as host. router Enter the keyword router to set the device-role as router. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
PAGE 1047
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. • • ipv6 nd ra-guard enable — configure the RA guard related commands.
PAGE 1048
ipv6 nd ra–guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 1049
Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. • ipv6 nd ra-guard enable — configure the RA guard related commands. managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters on Enter the keyword on to set the managed-config-flag value as ON.
PAGE 1050
ipv6–mac-access- Enter the keywords ipv6–mac-access-list then the mac-access-list name. The list name mac-access-list name allows a maximum of 140 characters. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.
PAGE 1051
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. • • ipv6 nd ra-guard enable — configure the RA guard related commands. ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode.
PAGE 1052
To reset the advertised reachability time, use the no reachable-timevalue command. Parameters value Enter the advertised reachability time in milliseconds. The range is from 0 to 3,600,000 milliseconds. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.
PAGE 1053
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. ipv6 nd ra-guard enable — configure the RA guard related commands. router–lifetime Set the router lifetime.
PAGE 1054
medium Enter the keyword medium to set the DRP value as medium. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.
PAGE 1055
ipv6 nd ra-guard policy test device-role router hop-limit maximum 251 mtu 1350 other-config-flag on reachable-time 540 retrans-timer 101 router-preference maximum medium trusted-port DellEMC(conf-ra_guard_policy_list)# Related Commands • • • • • • • • • • ipv6 nd ra-guard enable — configure the RA guard related commands. ipv6 nd ra-guard policy — define the RA guard policy name and enter the RA guard policy list configuration mode. device-role — specify the role of the device attached to the port.
PAGE 1056
match ra ipv6-access-list access other-config-flag on router-preference maximum medium trusted-port Interfaces : Te 1/1 DellEMC# Related Commands • • • • • • • • • • • ipv6 nd ra-guard enable — configure the RA guard related commands. ipv6 nd ra-guard policy — define the RA guard policy name and enter the RA guard policy list configuration mode. device-role — specify the role of the device attached to the port. hop-limit — enable the verification of the advertised hop count limit.
PAGE 1057
39 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell EMC Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1058
Example Version Description 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. DellEMC# debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface TenGigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1059
Related Commands • • • • track interface ip routing – configure object tracking on the routing status of an IPv4 Layer 3 interface. track interface line-protocol – configure object tracking on the line-protocol state of a Layer 2 interface. track ip route metric threshold – configure object tracking on the threshold of an IPv4 route metric. track ip route reachability – configure object tracking on the reachability of an IPv4 route. description Enter a description of a tracked object.
PAGE 1060
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Example DellEMC# show running-config track track 1 ip route 23.0.0.
PAGE 1061
resolution (OPTIONAL) Display information on the configured resolution values used to scale protocol-specific route metrics. The range is 0 to 255. brief (OPTIONAL) Display a single line summary of the tracking information for a specified object, object type, or all tracked objects. vrf vrf-name (OPTIONAL) E-Series only: Display information on only the tracked objects that are members of the specified VRF instance. The maximum is 32 characters.
PAGE 1062
First-hop interface is TenGigabitEthernet 1/2 Tracked by: VRRP TenGigabitEthernet 2/3 IPv6 VRID 1 Track 3 IPv6 route 2050::/64 reachability Reachability is Up (STATIC) 5 changes, last change 00:02:16 First-hop interface is TenGigabitEthernet 1/2 Tracked by: VRRP TenGigabitEthernet 2/3 IPv6 VRID 1 Usage Information The following describes the show track brief command shown in the Example below. Output Description ResID Number of the tracked object. Resource Type of tracked object.
PAGE 1063
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Usage Information Use this command to configure the UP and/or DOWN threshold for the scaled metric of a tracked IPv4 or IPv6 route.
PAGE 1064
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1065
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.
PAGE 1066
track ip route metric threshold Configure object tracking on the threshold of an IPv4 route metric. Syntax track object-id ip route ip-address/prefix-len metric threshold [vrf vrf-name] To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefix-len Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32.
PAGE 1067
• • threshold metric – configure the metric threshold used to determine the UP and/or DOWN state of a tracked route. track resolution ip route – configure the protocol-specific resolution value used to scale an IPv4 route metric. track ip route reachability Configure object tracking on the reachability of an IPv4 route. Syntax track object-id ip route ip-address/prefix-len reachability [vrf vrf-name] To return to the default setting, use the no track object-id command.
PAGE 1068
track reachability refresh Change the refresh interval for tracking the reachability of the next-hop. If the next-hop address in the ARP cache ages out for a route tracked for its reachability, an attempt is made to check if the next-hop address is reachable after a certain refresh interval before considering the route DOWN. Syntax track reachability refresh interval Parameters interval Enter the refresh interval, in seconds, for object tracking reachability. The range is from 0 to 60 seconds.
PAGE 1069
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced.
PAGE 1070
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1071
Ouput Description ResID Number of the tracked object. Resource Type of tracked object. Parameter Detailed description of the tracked object. State Up or Down state of the tracked object. Last Change Time since the last change in the state of the tracked object.
PAGE 1072
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Usage Information Use this command to create an object that tracks the routing state of an IPv6 Layer 3 interface: • • Related Commands • • The status of the IPv6 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IP address.
PAGE 1073
not match routing table entry 3333:100:200:300::/64. If no route-table entry has the exact IPv6 address and prefix length, the status of the tracked route is considered to be DOWN. When you configure the threshold of an IPv6 route metric as a tracked object, the UP/DOWN state of the tracked route is also determined by the current metric for the route in the routing table.
PAGE 1074
A tracked route is considered to match an entry in the routing table only if the exact IPv6 address and prefix length match a table entry. For example, when configured as a tracked route, 3333:100:200:300:400::/80 does not match routing table entry 3333:100:200:300::/64. If no route-table entry has the exact IPv6 address and prefix length, the tracked route is considered to be DOWN.
PAGE 1075
• • • • Related Commands • • For ISIS, you can set the resolution in the range 1 to 1000, where the default is 10. For OSPF, you can set the resolution in the range 1 to 1592, where the default is 1. The resolution value used to map static routes is not configurable. By default, Dell EMC Networking OS assigns a metric of 0 to static routes. The resolution value used to map RIP routes is not configurable. The RIP hop-count is automatically multiplied by 16 to scale it.
PAGE 1076
40 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1077
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.
PAGE 1078
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.
PAGE 1079
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1080
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information To configure all routers and access servers within a stub, use this command.
PAGE 1081
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables. S4048–ON Syntax Parameters clear ip ospf process-id [vrf vrf-name] [process] process-id Enter the OSPF Process ID to clear a specific process.
PAGE 1082
clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Syntax clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] Parameters process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all OSPF routing tables corresponding to that VRF.
PAGE 1083
debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process. S4048–ON Syntax debug ip ospf [process-id] [vrf vrf-name] [bfd |event | packet | spf | database-timer rate-limit] To cancel the debug command, use the no debug ip ospf command. Parameters process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared.
PAGE 1084
Field Description 8:14 Displays the time stamp. OSPF Displays the OSPF process ID: instance ID. v: Displays the OSPF version. Dell EMC Networking OS supports version 2 only. t: Displays the type of packet sent: • • • • • l: Displays the packet length. rid: Displays the OSPF router ID. aid: Displays the Autonomous System ID. chk: Displays the OSPF checksum. aut: States if OSPF authentication is configured.
PAGE 1085
Xmt. v:2 t:1(HELLO) l:44 rid:192.1.1.1 aid:0.0.0.1 chk:0xa098 aut:0 auk: keyid:0 to:Te 4/3 dst:224.0.0.5 netmask:255.255.255.0 pri:1 N-, MC-, E+, T-, hi:10 di:40 dr:90.1.1.1 bdr:0.0.0.0 default-information originate To generate a default external route into an OSPF routing domain, configure Dell EMC Networking Operating System (OS).
PAGE 1086
Related Commands • redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command. S4048–ON Syntax default-metric number To return to the default values, use the no default-metric [number] command. Parameters number Enter a number as the metric. The range is from 1 to 16777214. Defaults Disabled.
PAGE 1087
Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults None Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1088
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1089
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1090
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1091
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1092
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on all platforms. Usage Information The higher this parameter is set, the faster OSPF converge takes place.
PAGE 1093
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Added support for Multi-Process OSPF. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information The Helper mode is enabled by default on the device.
PAGE 1094
Version Description 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart mode Enable the graceful restart mode. S4048–ON Syntax graceful-restart mode [planned-only | unplanned-only] To disable graceful restart mode, use the no graceful-restart mode command. Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only.
PAGE 1095
graceful-restart role Specify the role for your OSPF router during graceful restart. S4048–ON Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command. Parameters role helper-only (OPTIONAL) Enter the keywords helper-only to specify the OSPF router is a helper only during graceful restart. role restart-only (OPTIONAL) Enter the keywords restart-only to specify the OSPF router is a restart only during graceful-restart.
PAGE 1096
Defaults zero (0) seconds. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1097
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1098
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information If this command is not configured, cost is based on the auto-cost command. When you configure OSPF over multiple vendors, to ensure that all routers use the same cost, use the ip ospf cost command. Otherwise, OSPF routes improperly. Related Commands • auto-cost — control how the OSPF interface cost is calculated.
PAGE 1099
Usage Information By default, the dead interval is four times the default hello-interval. Related Commands • ip ospf hello-interval — set the time interval between the hello packets. ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. S4048–ON Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535.
PAGE 1100
ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. S4048–ON Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command. Parameters keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. Defaults No MD5 authentication is configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1101
ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets. S4048–ON Syntax ip ospf mtu-ignore To return to the default, use the no ip ospf mtu-ignore command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1102
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1103
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information Setting a priority of 0 makes the router ineligible for election as a designated router or backup designated router.
PAGE 1104
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information Set the time interval to a number large enough to prevent unnecessary retransmissions. ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed. S4048–ON Syntax ip ospf transmit-delay seconds To return to the default value, use the no ip ospf transmit-delay command.
PAGE 1105
log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell EMC Networking OS. S4048–ON Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1106
ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1107
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1108
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1109
• • • Clear everything and revert to the default behavior. All previously marked passive interfaces are removed. May update ABR status. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute information from another routing protocol throughout the OSPF process.
PAGE 1110
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command. Despite removing an OSPF process globally, the OSPF process is not completely removed from the BGP configuration.
PAGE 1111
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.3 Added Route Map for BGP Redistribution to OSPF. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the keyword default. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1112
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1113
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information You can configure an arbitrary value in the IP address format for each router. However, each router ID must be unique.
PAGE 1114
Version Description 9.1(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information You must have an IP address assigned to an interface to enter ROUTER OSPF mode and configure OSPF.
PAGE 1115
Example DellEMC(conf-router_ospf)# show config ! router ospf 3 passive-interface 0 TenGigabitEthernet 1/1 DellEMC(conf-router_ospf)# show ip ospf Display information on the OSPF process configured on the switch. Syntax Parameters show ip ospf [process-id | vrf vrf name] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf name Show only the OSPF information tied to the VRF process.
PAGE 1116
Line Beginning Description with “Routing Process...” Displays the OSPF process ID and the IP address associated with the process ID. “Supports only...” Displays the number of Type of Service (TOS) rouse supported. “SPF schedule...” Displays the delay and hold time configured for this process ID. “Convergence Level” “Min LSA....” Displays the intervals set for LSA transmission and acceptance. “Number of...” Displays the number and type of areas configured for this process ID.
PAGE 1117
Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 1118
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1119
10.2.3.0 10.2.4.0 11.1.1.0 11.1.2.0 12.1.2.0 13.1.1.0 13.1.2.0 172.16.1.0 DellEMC> Related Commands • 11.1.2.1 13.1.1.1 11.1.2.1 11.1.2.1 192.68.135.2 13.1.1.1 13.1.1.1 13.1.1.1 718 1184 718 718 1663 1192 1184 148 0x80000002 0x80000068 0x80000002 0x80000002 0x80000054 0x8000006b 0x8000006b 0x8000006d 0x6e31 0x45db 0x831e 0x7828 0xd8d6 0x2718 0x1c22 0x533b 0 0 0 0 0 0 0 0 show ip ospf database asbr-summary — display only ASBR summary LSA information.
PAGE 1120
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information The following describes the show ip ospf database asbr-summary command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router.
PAGE 1121
Related Commands • show ip ospf database — display OSPF database information. show ip ospf database external Display information on the AS external (type 5) LSAs. Syntax Parameters show ip ospf [process-id | vrf vrf-name ] database external [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1122
Usage Information The following describes the show ip ospf process-id database external command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: • • • Example TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1123
Length: 36 Network Mask: /24 Metrics Type: 2 TOS: 0 Metrics: 1 Forward Address: 0.0.0.0 External Route Tag: 701 DellEMC# Related Commands • show ip ospf database — display OSPF database information. show ip ospf database network Display the network (type 2) LSA information. Syntax Parameters show ip ospf [process-id] database network [link-state-id] [adv-router ipaddress] process-id Enter the OSPF Process ID to show a specific process.
PAGE 1124
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. Usage Information The following describes the show ip ospf process-id database network command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router.
PAGE 1125
Attached Router: 20.20.20.5 DellEMC# Related Commands • show ip ospf database — display OSPF database information. graceful-restart grace-period Enable OSPFv3 graceful restart globally by setting the grace period (in seconds) that an OSPFv3 router’s neighbors continues to advertise the router as adjacent during a graceful restart. Syntax graceful-restart grace-period seconds To disable OSPFv3 graceful restart, enter no graceful-restart grace-period.
PAGE 1126
graceful-restart mode Specify the type of events that trigger an OSPFv3 graceful restart. Syntax graceful-restart mode {planned-only | unplanned-only} To disable graceful restart mode, enter no graceful-restart mode. Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only.
PAGE 1127
area area-id Specify the OSPF area. The range is from 0 to 4294967295. Defaults None Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.2) Increased the area ID value from 65535 to 4294967295. 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1128
Version Description 9.12(1.0) Introduced on the S5048F–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1129
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.0 Introduced on the Z9000, S4820T, and S4810.
PAGE 1130
Using this formula, the default path cost is calculated as: • • • • GigabitEthernet — Default cost is 1 TenGigabitEthernet — Default cost is 1 FortygigEthernet — Default cost is 1 Ethernet — Default cost is 10 ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down.
PAGE 1131
esp encryption- algorithm Encryption algorithm used with ESP. Valid values are: 3DES, DES, AES-CBC, and NULL. For AES-CBC, only the AES-128 and AES-192 ciphers are supported. key-encryptiontype (OPTIONAL) Specifies if the key is encrypted. key Text string used in authentication. Valid values: 0 (key is not encrypted) or 7 (key is encrypted).
PAGE 1132
authentication policy configured for the OSPFv3 area, enter the no ipv6 ospf no ipv6 ospf encryption null command. ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured.
PAGE 1133
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 1134
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 1135
Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters number Specify the number of paths. The range is from 1 to 64. The default is 8 paths.
PAGE 1136
Parameters interface Enter the following keywords and slot/port or number information: • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a port channel interface, enter the keywords port-channel then a number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1137
connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. metric metric- Enter the keyword metric then the metric value. value The range is from 0 to 16777214. The default is 20. metric-type type- value (OPTIONAL) Enter the keywords metric-type then the OSPFv3 link state type of 1 or 2 for default routes.
PAGE 1138
To return to the previous router ID, use the no router-id ip-address command. Parameters ip-address Enter the router ID in the dotted decimal format. Defaults The router ID is selected automatically from the set of IPv4 addresses configured on a router. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1139
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1140
Field Description Inbound ESP SPI and Outbound ESP SPI The encapsulating security payload (ESP) security policy index (SPI) for inbound and outbound links. Inbound ESP Auth The ESP authentication key for inbound and outbound links. Key and Outbound Auth Key Inbound ESP Cipher Key and Outbound ESP Cipher Key The ESP encryption key for inbound and outbound links. Transform set The set of security protocols and algorithms used in the policy.
PAGE 1141
Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Usage Information The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router. Related Commands show crypto ipsec policy – displays the configuration of IPsec authentication and encryption policies.
PAGE 1142
Field Description Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/outbound Authentication policy applied to inbound or outbound traffic. ah inbound/outbound Encryption policy applied to inbound or outbound traffic. esp spi Security policy index number used to identify the policy. transform Security algorithm that is used to provide authentication, integrity, and confidentiality.
PAGE 1143
EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14.1.0 The support to display detailed information of all the types of LSAs is introduced in S4810 and S4820T. 9.13(0.0) Added support to display all the types of LSAs in detail. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1144
Rte Max Eq Cost Paths 10 GR grace-period 180 GR mode planned and unplanned Area 0 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 6 Rtr LSA Count 2 Net LSA Count 1 Inter Area Pfx LSA Count 1 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 Area 1 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 8 Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area Rtr LSA C
PAGE 1145
Metric Type: 2 Metric: 20 Forwarding Address: 101:101:1::1 show ipv6 ospf interface View OSPFv3 interface information. Syntax Parameters show ipv6 ospf [process-number] [vrf vrf-name] [interface] process-number Enter the OSPF process number. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
PAGE 1146
Example DellEMC# show ipv6 ospf 3 interface tengigabitethernet 1/2 TenGigabitEthernet 1/2 is up, line protocol is up Link Local Address fe80::201:e8ff:fe17:5bbd, Interface ID 67420217 Area 0, Process ID 1, Instance ID 0, Router ID 11.1.1.1 NetworkType BROADCAST, Cost: 1, Passive: No Transmit Delay is 100 sec, State DR, Priority 1 Interface is using OSPF global mode BFD configuration. Designated router on this network is 11.1.1.
PAGE 1147
Example Version Description 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. DellEMC# show ipv6 ospf 3 neighbor gi 1/2 Neighbor ID 63.114.8.36 Pri State 1 FULL/DR Dead Time 00:00:38 Interface 4 ID Interface Te 1/2 DellEMC# snmp context Configure SNMPv3 context name to map multiple OSPFv3 VRF instances. Syntax snmp context {context-name} To clear snmp context, use the no snmp context {context-name} command.
PAGE 1148
Parameters delay Enter a number as the delay. The range is from 0 to 2147483647. The default is 5 seconds. When configured in milli seconds, 100 is the least value that is allowed to be configured. holdtime Enter a number as the hold time. The range is from 0 to 2147483647. The default is 10 seconds. When configured in milli seconds, 200 is the least value that is allowed to be configured. msec Enter the keyword msec to specify the time interval value in milli seconds.
PAGE 1149
41 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell EMC Networking OS.
PAGE 1150
Related Commands Version Description 7.7.1.0 Introduced on the E-Series. • ip redirect-list – enable an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name test [l2–switch] To remove a redirect list from an interface, use the no ip redirect-group name command.
PAGE 1151
NOTE: The l2–switch option that redirects Layer2 traffic is applicable only on VLAN interfaces. The Layer3 routing is not affected on the same interface on which Layer2 PBR is applied. The port from which Layer2 packets egress and the destination MAC are re-written from static ARP. Layer 2 packets with the rewritten destination MAC are forwarded through the outgoing port on the same incoming VLAN interface. The l2switch option ensures that the outgoing VLAN and MAC-SA are changed and TTL is not decremented.
PAGE 1152
• • Parameters If you know the filter sequence number, use the no seq sequence-number syntax command. You can also use the no permit {ip-protocol-number | protocol-type} {source mask | any | host ip-address} {destination mask | any | host ip-address} [bit] [operators] command. ip-protocolnumber Enter a number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1153
Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.5.1.0 Introduced on the E-Series. redirect Configure a rule for the redirect list.
PAGE 1154
host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent. operator (OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand: • • • • • eq = equal to neq = not equal to gt = greater than lt = less than range = inclusive range of ports (you must specify two ports for theport command parameter.
PAGE 1155
ip-address Enter the keyword IP address of the forwarding router. tunnel Enter the keyword tunnel to configure the tunnel setting. tunnel-id Enter the keyword tunnel-id to redirect the traffic. track Enter the keyword track to enable the tracking. track Enter the keyword track to track object-id. ip-protocolnumber Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1156
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, S6000-ON, and Z9000. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1157
00003 5 00004 5 DellEMC# Related Commands • • N/A N/A UDP IP 0x0 0x0 0 0 0 0 55.1.3.0/24 0.0.0.0/0 66.6.6.6/32 0.0.0.0/0 00:01:e8:8a:fd:76 Po 128 00:01:e8:8a:fd:76 Vl 1020(Po 100) ip redirect-group – applies a redirect group to an interface. show ip redirect-list – displays the redirect-list configuration. show ip redirect-list View the redirect list configuration and the interfaces it is applied to.
PAGE 1158
, Track 200 [up], Next-hop reachable (via Te 2/18) , Track 200 [up], Next-hop reachable (via Te 2/19) DellEMC# 1158 Policy-based Routing (PBR)
PAGE 1159
42 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell EMC Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. Topics: • • IPv4 PIM-Sparse Mode Commands IPv6 PIM-Sparse Mode Commands IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands.
PAGE 1160
Version Description 7.8.1.0 Introduced on the S-Series. Usage Information This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1161
debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug all to disable all debugging command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF.
PAGE 1162
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface. Syntax ip pim bsr-border To return to the default value, use the no ip pim bsr-border command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1163
interface Enter the following keywords and slot/port or number information: • • • • • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a Port Channel interface, enter the keywords port-channel then a number. For a VLAN, enter the keyword vlan then a number from 1 to 4094. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1164
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1165
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. 7.7.1.0 Introduced on the E-Series. Usage Information When you configure a join filter, it is applicable for both ingress and egress flows.
PAGE 1166
DellEMC(config-if-te-1/1)# ip pim ingress-interface-map map1 DellEMC(config-if-te-1/1)# ip pim neighbor-filter To prevent a router from participating in protocol independent multicast (PIM), configure this feature. Syntax ip pim [vrf vrf-name] neighbor-filter {access-list} To remove the restriction, use the no ip pim [vrf vrf-name] neighbor-filter {access-list} command.
PAGE 1167
To return to the default value, use the no ip pim query-interval seconds command. Parameters seconds Enter a number as the number of seconds between router query messages. The range is from 0 to 65535. The default is 30 seconds. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1168
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1169
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 1170
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the acl-name parameter. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1171
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. Usage Information The interface must be enabled (the no shutdown command) and not have the switchport command configured. Multicast must also be enabled globally (using the ip multicast-lag-hashing command). PIM is supported on the port-channel interface. ip pim sparse-mode sg-expiry-timer Enable expiry timers globally for all sources.
PAGE 1172
Version Description 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. 7.7.1.1 Introduced Usage Information This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL. Even though the FHR nodes act as RPs, these nodes still send Register encap messages to themselves and expect to receive a Register stop message (for Anycast RP support).
PAGE 1173
Usage Information Dell EMC Networking OS supports standard access lists for the SSM range. You cannot use extended ACLs for configuring the SSM range. If you configure an extended ACL and then used in the ip pim ssm-range {access list name} configuration, an error is reported. However, if you configure ip pim ssm-range {access list name} first and then you configure the ACL as an Extended ACL, an error is not reported and the ACL is not applied to the SSM range.
PAGE 1174
Usage Information This command is applicable to last hop routers on the shared tree towards the rendezvous point (RP). no ip pim snooping dr-flood Disable the flooding of multicast packets to the PIM designated router. Syntax no ip pim snooping dr-flood To re-enable the flooding of multicast packets to the PIM designated router, use the ip pim snooping drflood command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1175
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1176
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1177
show ip pim neighbor View PIM neighbors. S4048–ON Syntax Parameters show ip pim [vrf vrf-name] neighbor vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1178
Field Description • • Example DR = Designated Router S = Sparse mode DellEMC# show ip pim neighbor Neighbor Interface Uptime/Expires Ver Address 127.87.3.4 Te 1/16 09:44:58/00:01:24 v2 DellEMC# DR Prio/Mode 1 / S show ip pim rp View all multicast groups-to-RP mappings. S4048–ON Syntax show ip pim [vrf vrf-name] rp [mapping | group-address] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 1179
Example DellEMC# show ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.4 224.3.3.3 165.87.20.4 225.1.2.1 165.87.20.4 225.1.2.2 165.87.20.4 229.1.2.1 165.87.20.4 229.1.2.2 165.87.20.4 DellEMC# Example (Mapping) DellEMC# show ip pim rp mapping PIM Group-to-RP Mappings Group(s): 224.0.0.0/4, Static RP: 50.40.4.4, v2 DellEMC# Example (Address) DellEMC# show ip pim rp 229.1.2.1 Group RP 229.1.2.1 165.87.20.
PAGE 1180
Field Description DR Prio Displays the Designated Router priority value configured on the interface (ip pim drpriority command). DR Displays the IP address of the Designated Router for that interface. Example (#2) DellEMC# show ip pim Interface Ver Nbr Count Vlan 2 v2 3 DellEMC# snooping interface DR DR Prio 1 165.87.32.2 show ip pim snooping neighbor Display information on PIM neighbors learned through PIM-SM snooping.
PAGE 1181
Example DellEMC# show ip pim snooping neighbor Neighbor Interface Uptime/Expires Ver Address 165.87.32.2 Vl 2 [Te 1/13 ] 00:04:03/00:01:42 v2 165.87.32.10 Vl 2 [Te 1/11 ] 00:00:46/00:01:29 v2 165.87.32.12 Vl 2 [Te 2/20 ] 00:00:51/00:01:24 v2 DR Prio 1 0 0 show ip pim snooping tib Display information from the tree information base (TIB) PIM-SM snooping discovered about multicast group members and states.
PAGE 1182
Field Description Incoming interface Displays the reverse path forwarding (RPF) interface towards the RP/ source. RPF neighbor Displays the next hop from this interface towards the RP/source.
PAGE 1183
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1184
Example Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.1 Support for the display of PIM-SM snooping status was added on E-Series. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1185
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D). source-address (OPTIONAL) Enter the source address in dotted decimal format (A.B.C.D). Command Modes • • Command History This guide is platform-specific.
PAGE 1186
Field Description • K = acknowledge pending state Incoming interface Displays the reverse path forwarding (RPF) interface towards the RP/ source. Example RPF neighbor Displays the next hop from this interface towards the RP/source.
PAGE 1187
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the E-Series. DellEMC# show running-config pim ! ip pim rp-address 100.0.0.1 group-address 224.0.0.0/4 ip pim vrf VRF2 rp-address 100.0.0.1 group-address 224.0.0.
PAGE 1188
NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. bsr (OPTIONAL) Enter the keyword bsr to invoke debugging of IPv6 PIM Candidate RP/BSR activities. events (OPTIONAL) Enter the keyword events to invoke debugging of IPv6 PIM events. group [group] (OPTIONAL) Enter the keyword group followed by the group address to invoke debugging on that specific group. packet (OPTIONAL) Enter the keyword packet to invoke debugging of IPv6 PIM packets.
PAGE 1189
interface Enter the following keywords and slot/port or number information: • • • • • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a Port Channel interface, enter the keywords port-channel then a number. For a VLAN, enter the keyword vlan then a number from 1 to 4094. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information.
PAGE 1190
ipv6 pim query-interval Change the frequency of IPv6 PIM router-query messages. Syntax ipv6 pim query-interval seconds To return to the default value, use the no ipv6 pim query-interval seconds command. Parameters seconds Enter a number as the number of seconds between router query messages. The range is from 0 to 65535. The default is 30 seconds. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1191
Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. Usage Information The device selects the RP based on the longest prefix match of the configured group address when both static and dynamic RPs are configured. The override option allow you to use statically configured RP instead of the longest prefix match of the configured group address associated with a dynamic RP.
PAGE 1192
ipv6 pim sparse-mode Enable IPv6 PIM sparse mode and MLD on the interface. Syntax ipv6 pim sparse-mode To disable IPv6 PIM sparse mode and MLD on the interface, use the no ipv6 pim sparse-mode command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1193
ipv6 pim spt-threshold Specifies when a PIM leaf router should join the shortest path tree. Syntax ipv6 pim [vrf vrf-name] spt-threshold {infinity} To return to the default value, use the no ipv6 pim spt-threshold command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1194
show ipv6 pim interface Display IPv6 PIM enabled interfaces. Syntax show ipv6 pim [vrf vrf-name] interface Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes • • Command History This guide is platform-specific.
PAGE 1195
Version Description 9.11.3.0 Introduced on the Z9100-ON, S4048-ON, S6000-ON, S6100-ON, S4048T-ON, S3100, S6010-ON, S3048-ON, and C9010. Example DellEMC#show ipv6 pim neighbor Neighbor Interface Uptime/Expires Address fe80::201:e8ff:fe02:140f Te 1/11 01:44:59/00:01:16 fe80::201:e8ff:fe00:6265 Te 1/12 01:45:00/00:01:16 DellEMC# Ver v2 v2 DR Prio/Mode 1 / S 1 / DR show ipv6 pim rp View all IPv6 multicast groups-to-rendezvous point (RP) mappings.
PAGE 1196
Example (Mapping) DellEMC#show ipv6 pim rp mapping PIM Group-to-RP Mappings Group(s): ff0e::225:1:1:1/128 RP: 100::1, v2 Info source: 200::1, via bootstrap, expires: 00:01:50 RP: 150::1, v2 Info source: 200::1, via bootstrap, expires: 00:01:50 RP: 200::1, v2 Info source: 200::1, via bootstrap, expires: 00:01:57 Group(s): ff0e::225:1:1:2/128 RP: 100::1, v2 Info source: 200::1, via bootstrap, expires: 00:01:50 RP: 150::1, v2 Info source: 200::1, via bootstrap, expires: 00:01:50 RP: 200::1, v2 Info source: 20
PAGE 1197
69/69 (S,G) entries in PIM-TIB/MFC 24/0 (S,G,Rpt) entries in PIM-TIB/MFC 8 PIM nexthops 1 RPs 7 sources 30 Register states Message summary: 47132/53793 Joins/Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 MSDP updates sent/received 243746/0 Null Register messages sent/received 0/973809 Register-stop messages sent/received Data path event summary: 222 no-cache messages received 281 last-hop switchover messages received 26260/2958 pim-assert messages sent
PAGE 1198
(25::1, ff0e::225:1:2:1), uptime 00:09:53, expires 00:00:00,flags: CJ RPF neighbor: TenGigabitEthernet 1/3, fe80::201:e8ff:fe00:6265 Outgoing interface list: TenGigabitEthernet 2/11 (25::1, ff0e::225:1:2:2), uptime 00:09:54, expires 00:00:00,flags: CJ RPF neighbor: TenGigabitEthernet 1/3, fe80::201:e8ff:fe00:6265 Outgoing interface list: TenGigabitEthernet 1/11 (25::2, ff0e::225:1:2:2), uptime 00:09:54, expires 00:00:00,flags: CJ RPF neighbor: TenGigabitEthernet 1/3, fe80::201:e8ff:fe00:6265 Outgoing interf
PAGE 1199
43 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember • • • • • • • Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1200
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1201
monitor multicast-queue Configure monitor QoS multicast queue ID. Syntax monitor multicast-queue queue-id To remove the configuration, use the no monitor multicast-queue command. Parameters Defaults queue-id Enter the QoS multicast queue ID. The range is from 0 to 9. queue-id: 0 Enable status: Disabled Command Modes Example Command History CONFIGURATION DellEMC(conf)#monitor multicast-queue 7 This guide is platform-specific.
PAGE 1202
dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default configuration, use the no form of this command. ttl_value IP TTL value of the ERSPAN traffic. The range is from 1 to 255. The default value is 255. drop Monitors only the dropped packets in the Ingress.
PAGE 1203
Parameters limit Enter the rate-limit value. The range is from 0 to 40000 Megabits per second. Defaults 60 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1204
Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Example DellEMC(conf-mon-sess-1)# show config ! monitor session 1 source TenGigabitEthernet 1/1 destination Port-channel 1 direction rx show monitor session Display information about monitoring sessions. Syntax show monitor session {session-ID} [access-list] To display monitoring information for all sessions, use the show monitor session command.
PAGE 1205
Version Description 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Example DellEMC# show monitor session 1 SessID Source Destination Dir Mode Source IP IP DSCP TTL Drop Rate Gre-Protocol FcMonitor ------ ------------------ ---- ------------------- ------ -------------- --------1 Te 1/2 remote-ip rx Port 0.0.0.0 0.0.0.
PAGE 1206
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1207
destination Enter the keyword destination to specify the destination interface. • • • interface Enter one of the following keywords and slot/port information: • • • • direction {rx | tx | both} For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a port channel interface, enter the keywords port-channel then a number.
PAGE 1208
Example 1208 DellEMC# monitor session 0 source Port-channel 10 destination TenGigabitEthernet 1/3 direction tx DellEMC# Port Monitoring
PAGE 1209
44 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell EMC Networking OS is supported on the platforms. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell EMC Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1210
ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. S4048 Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip localproxy-arp command in INTERFACE VLAN mode for the primary VLAN. To disable Layer 3 communication in a particular secondary VLAN, use the no ip local-proxy-arp command in INTERFACE VLAN mode for the selected secondary VLAN.
PAGE 1211
private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. S4048 Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters community Enter the keyword community to set the VLAN as a community VLAN. isolated Enter the keyword isolated to configure the VLAN as an isolated VLAN.
PAGE 1212
private-vlan mapping secondary-vlan Map secondary VLANs to the selected primary VLAN. Syntax [no] private-vlan mapping secondary-vlan vlan-list To remove specific secondary VLANs from the configuration, use the no private-vlan mapping secondary-vlan vlan-list command syntax. Parameters vlan-list Enter the list of secondary VLANs to associate with the selected primary VLAN. The list can be in comma-delimited or hyphenated-range format, following the convention for the range input.
PAGE 1213
Parameters host Enter the keyword host to configure the selected port or port channel as an isolated interface in a PVLAN. promiscuous Enter the keyword promiscuous to configure the selected port or port channel as an promiscuous interface. trunk Enter the keyword trunk to configure the selected port or port channel as a trunk port in a PVLAN. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1214
45 Per-VLAN Spanning Tree Plus (PVST+) The Dell EMC Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell EMC Networking OS supports PVST+ on the S4048 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1215
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced. • protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S4048 Syntax disable To enable PVST+, use the no disable command. Defaults Disabled.
PAGE 1216
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S4048 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History This guide is platform-specific.
PAGE 1217
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1218
show spanning-tree pvst View the Per-VLAN spanning tree configuration. S4048 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1219
Version Description 6.2.1.1 Introduced. Usage Information The following describes the show spanning-tree pvst command shown in the following examples. Example (Brief) Field Description Interface Name PVST interface. Instance PVST instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1220
Port 146 (TenGigabitEthernet 1/16) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.146 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.
PAGE 1221
spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
PAGE 1222
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series, C-Series, and SSeries. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the hardware shutdown-on-violation option. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1223
spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. S4048 Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1224
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1225
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced.
PAGE 1226
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. • • • • vlan bridge-priority — sets the bridge-priority value.
PAGE 1227
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. • • • • vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — changes the time interval before Dell EMC Networking OS transitions to the forwarding state. vlan max-age — changes the time interval before PVST+ refreshes.
PAGE 1228
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. • • • • 1228 vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — changes the time interval before Dell EMC Networking OS transitions to the forwarding state. vlan hello-time — changes the time interval between BPDUs. show spanning-tree pvst — displays the PVST+ configuration.
PAGE 1229
46 Quality of Service (QoS) The Dell EMC Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell EMC Networking products. Topics: • • • • Global Configuration Commands Per-Port QoS Commands Policy-Based QoS Commands DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1230
Usage Information By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives.
PAGE 1231
rate police Police the incoming traffic rate on the selected interface. Syntax Parameters rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burst-KB]] [vlan vlan-id] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps). committed-rate Enter the bandwidth in Mbps. The range is from 0 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB.
PAGE 1232
rate-shape Shape the traffic output on the selected interface. Syntax rate shape [kbps] rate [burst-KB] Parameters kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). Enter the value in multiples of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps). rate The range is from 10 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB. The range is from 0 to 10000. The default is 50.
PAGE 1233
service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. S4048–ON Syntax Parameters Defaults service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} queue Enter a value from 0 to 7. For each dot1p Priority, the default CoS queue value is: • Dot1p Priority : 0 1 2 3 4 5 6 7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1234
dot1p Queue ID 1 0 2 0 3 1 4 2 5 3 6 3 7 3 Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. INTERFACE CONFIGURATION Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.
PAGE 1235
strict-priority unicast Configure a unicast queue as a strict-priority (SP) queue. Syntax Parameters strict-priority unicast number unicast number Enter the keyword unicast then the queue number. The range is from 1 to 3. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1236
Parameters percentage Enter the percentage assignment of bandwidth to the class/queue. The range is from 1 to 100% (granularity 1%). Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1237
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1238
• • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defaults none Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands EXEC EXEC Privilege Version Description 9.10(0.
PAGE 1239
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1240
Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1241
Defaults none Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option for the class-map on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1242
Parameters seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100. By default, the sequence number are assigned in multiples of five. ip Enter the keyword ip to support IPv4 traffic. ipv6 Enter the keyword ipv6 to support IPv6 traffic. ip-any Enter the keyword ip-any to support IPv4 and IPv6 traffic. ip-precedence-list Enter the IP precedence value(s) as the match criteria.
PAGE 1243
NOTE: Only one of the IP precedence values must be a successful match criterion, not all of the specified IP precedence values must match. Related Commands • class-map — identifies the class map. match ip vlan Uses a VLAN as the match criterion for an L3 class map. Syntax Parameters [seq sequence number] match ip vlan vlan-idTo remove VLAN as the match criterion, use the no [seq sequence number] match ip vlan vlan-id command.
PAGE 1244
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5.(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. Usage Information To access this command, enter the class-map command.
PAGE 1245
Version Description 7.4.1.0 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands • class-map — identifies the class map. match mac dot1p Configure a match criterion for a class map based on a dot1p value. Syntax Parameters [seq sequence number] match mac dot1p {dot1p-list} seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number.
PAGE 1246
match mac vlan Configure a match criterion for a class map based on VLAN ID. Syntax [seq sequence number] match mac vlan number Parameters seq sequence number (OPTIONAL) Enter the keyword seq then the sequence number. The range is from 1 to 100. By default, the sequence number are assigned in multiples of five. number Enter the VLAN ID. The range is from 1 to 4094. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific.
PAGE 1247
Command Modes CONFIGURATION (policy-map-input and policy-map-output) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1248
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1249
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 1250
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1251
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy.
PAGE 1252
Version Description 7.5.1.0 Added support for multicast-bandwidth. 7.4.1.0 and 6.5.3.0 Introduced on the E-Series. Usage Information This command does not uniquely identify a queue, but rather identifies only a set of queues. The WRED curve is applied to all eight egress Multicast queues. Important Points to Remember — Multicast-Bandwidth Option • • • • • • A unique multicast weighted fair queuing (WFQ) setting can be applied only on a per port-pipe basis.
PAGE 1253
Usage Information This command does not uniquely identify a queue, but rather identifies only a set of queues. The WRED Curve is applied to all eight ingress Multicast queues. NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast. rate-police Specify the policing functionality on incoming traffic.
PAGE 1254
Usage Information The default burst size is 100Kb. If a different value is required, you must configure the burst size to the required value. Related Commands • • rate police — specifies traffic policing on the selected interface. qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy.
PAGE 1255
committed burst. Committed rate refers to the guaranteed bandwidth for traffic entering or leaving the interface under normal network conditions. When traffic propagates at an average rate that is less than or equal to the committed rate, it is considered to be green-colored or coded. When the transmitted traffic falls below the committed rate, the bandwidth, which is not used by any traffic that is traversing the network, is aggregated to form the committed burst size.
PAGE 1256
Usage Information You can attach a single policy-map to one or more interfaces to specify the service-policy for those interfaces. A policy map attached to an interface can be modified. NOTE: The service-policy commands are not allowed on a port channel. The service-policy input policy-map-name command and the service-class dynamic dot1p command are not allowed simultaneously on an interface.
PAGE 1257
service-queue Assign a class map and QoS policy to different queues. S4048–ON Syntax service-queue queue-id [class-map class-map-name] [qos-policy qos-policy-name] To remove the queue assignment, use the no service-queue queue-id [class-map class-mapname] [qos-policy qos-policy-name] command. Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7.
PAGE 1258
set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. S4048–ON Syntax set {ip-dscp value | mac-dot1p value} Parameters ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63. mac-dot1p value Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7. Defaults none Command Modes CONFIGURATION (conf-qos-policy-in) Command History This guide is platform-specific.
PAGE 1259
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Introduced the seq option on all the Dell EMC Networking OS platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1260
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information trust dot1p, do1p-priority, service-class dynamic dot1; all these features work over the mapping in this command output.
PAGE 1261
Example (IPv4) Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1262
show qos policy-map-input View the input QoS policy map details. S4048–ON Syntax show qos policy-map-input [policy-map-name] [class class-map-name] [qos-policyinput qos-policy-name] Parameters policy-map-name Enter the policy map name. class class-mapname Enter the keyword class then the class map name. qos-policy-input Enter the keyword qos-policy-input then the QoS policy name. qos-policy-name Defaults none Command Modes • • Command History This guide is platform-specific.
PAGE 1263
Policy-map-input pmap1 Trust ipv6-diffserv Queue# Class-map-name 0 c0 1 c1 2 c2 3 c3 4 c4 5 c5 6 c6 7 c7 DellEMC# Qos-policy-name q0 q1 q2 q3 q4 q6 q7 show qos policy-map-output View the output QoS policy map details. S4048–ON Syntax Parameters show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] policy-map-name Enter the policy map name. qos-policy-output Enter the keyword qos-policy-output then the QoS policy name.
PAGE 1264
Policy-map-output PolicyMapOutput Aggregate Qos-policy-name AggPolicyOut Queue# Qos-policy-name 0 qosPolicyOutput DellEMC# show qos qos-policy-input View the input QoS policy details. S4048–ON Syntax show qos qos-policy-input [qos-policy-name] Parameters qos-policy-name Enter the QoS policy name. Defaults none Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1265
show qos qos-policy-output View the output QoS policy details. S4048–ON Syntax Parameters show qos qos-policy-output [qos-policy-name] qos-policy-name Enter the QoS policy name. Defaults none Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1266
• • wred-profile interface Enter the keywords wred-profile and optionally one of the following keywords and slot/port or number information: • • interface For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information.
PAGE 1267
with per queue per port tx and drop rates Example of show qos statistics wred-profile DellEMC(conf)#do show qos statistics wred-profile Global Wred State : Enabled Interface Te 1/11 Drop-statistic Dropped Pkts Green 0 Yellow 6730113 Out of Profile 0 Usage Information In a dual homing setup, you can use this command only from the primary VLT peer. The following list describes output of the show qos statistics command in the example: • • • • Queue # — Queue Number.
PAGE 1268
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. DellEMC# show qos wred-profile Global Wred State: Disabled Wred-profile-name wred_drop wred_teng_y wred_teng_g wred_fortyg_y wred_fortyg_g DellEMC# min-threshold 0 467 467 467 467 max-threshold 0 4671 4671 4671 4671 max-drop-rate 100 100 50 50 25 test cam-usage Check the Input Policy Map configuration for the CAM usage.
PAGE 1269
Version Description 8.3.7.0 Introduced on the S4810. Usage Information This feature allows you to determine if the CAM has enough space available before applying the configuration on an interface. An input policy map with both Trust and Class-map configuration, the Class-map rules are ignored and only the Trust rule is programmed in the CAM. In such an instance, the Estimated CAM output column contains the size of the CAM space required for the Trust rule and not the Class-map rule.
PAGE 1270
threshold Specify the minimum and maximum threshold values for the configured WRED profiles. S4048–ON Syntax threshold min number max number max-drop-drop To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360. max number Enter the keyword max then the maximum threshold number for the WRED profile. The range is from 1 to 9360 KB.
PAGE 1271
Related Commands Pre-Defined WRED Profile Name Minimum Threshold Maximum Threshold wred_fortyg_g 467 4671 • 25 wred-profile — creates a WRED profile. trust Specify dynamic classification (DSCP) or dot1p to trust. S4048–ON Syntax Parameters trust {diffserv [fallback]| dot1p [fallback]} diffserv Enter the keyword diffserv to specify trust of DSCP markings. dot1p Enter the keyword dot1p to specify trust dot1p configuration.
PAGE 1272
Usage Information When you configure trust, matched bytes/packets counters are not incremented in the show qos statistics command. Dynamic mapping honors packets marked according to the standard definitions of DSCP. The following lists the default mapping. Table 6.
PAGE 1273
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information To assign drop precedence to green or yellow traffic, use this command. If there is no honoring enabled on the input, all the traffic defaults to green drop precedence.
PAGE 1274
When you enable wred ecn, and the number of packets in the queue is between the minimum threshold and the maximum threshold, one of the following two scenarios can occur: • • If the transmission endpoints are ECN-capable and traffic is congested, and the WRED algorithm determines that the packet should have been dropped based on the drop probability, the packet is transmitted and marked so the routers know the system is congested and can slow transmission rates.
PAGE 1275
Version Description 6.1.1.1 Introduced on the E-Series. Usage Information Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred). Related Commands • threshold — specifies the minimum and maximum threshold values of the WRED profile. DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red.
PAGE 1276
Important Points to Remember • • • Example Related Commands All DSCP values that are not specified as yellow or red are colored green. A DSCP value cannot be in both the yellow and red lists. Setting the red or yellow list with any DSCP value that is already in the other list results in an error and no update to that list is made. Each color map can only have one list of DSCP values for each color; any DSCP values previously listed for that color that are not in the new DSCP list are colored green.
PAGE 1277
qos dscp-color-policy Associates the DSCP color map profile with an interface so that all IP packets received on it is given a color based on that color map. Syntax dscp-color-policy color-map-profile-name To remove a color policy map profile, use the no dscp-color-policy color-map-profile-name command. Parameters color-map-profile- Enter the color map profile name. The name can have a maximum of 32 characters.
PAGE 1278
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1279
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps.
PAGE 1280
47 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell EMC Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2). The Dell EMC Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell EMC Networking OS Configuration Guide.
PAGE 1281
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1282
Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information This command triggers updates of the main RIP routing tables. debug ip rip Examine RIP routing information for troubleshooting. S4048–ON Syntax debug ip rip [interface | database | events [interface] | trigger] To turn off debugging output, use the no debug ip rip command.
PAGE 1283
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-information originate Generate a default route for the RIP traffic. S4048–ON Syntax default-information originate [always] [metric metric-value] [route-map mapname] To return to the default values, use the no default-information originate command.
PAGE 1284
Usage Information The default route must be present in the switch routing table for the default-information originate command to take effect. default-metric Change the default metric for routes. To ensure that all redistributed routes use the same metric value, use this command with the redistribute command. S4048–ON Syntax default-metric number To return the default metric to the original values, use the no default-metric command. Parameters number Specify a number. The range is from 1 to 16.
PAGE 1285
description Enter a description of the RIP routing protocol. S4048–ON Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the RIP protocol (80 characters maximum). Defaults none Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1286
mask If you enter an IP address, also enter a mask for that IP address, in either dotted decimal format or /prefix format (/x). prefix-name (OPTIONAL) Enter a configured prefix list name. Defaults weight = 120 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1287
Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1288
isis (OPTIONAL) Enter the keyword isis to filter only IS-IS routes. ospf (OPTIONAL) Enter the keyword ospf to filter all OSPF routes. static (OPTIONAL) Enter the keyword static to filter manually configured routes. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 1289
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1290
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1291
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable the interface to send both version of RIP packets, use the ip rip send version 1 2 command. Related Commands • • ip rip receive version — sets the RIP version for the interface to receive traffic.
PAGE 1292
Related Commands • ip poison-reverse — sets the prefix for RIP routing updates. maximum-paths Set RIP to forward packets over multiple paths. S4048–ON Syntax maximum-paths number To return to the default values, use the no maximum-paths commands. Parameters number Enter the number of paths. The range is from 1 to 16. The default is 4 paths. Defaults 4 Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1293
Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1294
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1295
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1296
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1297
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1298
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command. Related Commands • default-information originate — generates a default route for RIP traffic. redistribute isis Redistribute routing information from an IS-IS instance.
PAGE 1299
redistribute ospf Redistribute routing information from an OSPF process. Syntax redistribute ospf process-id [match external {1 | 2} | match internal | metric metric-value] [route-map map-name] To disable redistribution, use the no redistribute ospf process-id [match external {1 | 2} | match internal | metric metric-value] [route-map map-name] command. Parameters process-id Enter a number that corresponds to the OSPF process ID to redistribute. The range is from 1 to 65355.
PAGE 1300
To disable RIP, use the no router rip command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1301
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.
PAGE 1302
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information The following describes the show ip rip database command shown in the following example.
PAGE 1303
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1304
holddown Enter the number of seconds to specify a time interval during which the route is marked as unreachable but still sending RIP packets. The holddown value should be at least three times the update timer value. The range is from zero (0) to 4294967295. The default is 180 seconds. flush Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table.
PAGE 1305
2 Enter the keyword 2 to specify RIP version 2. Defaults The Dell EMC Networking OS sends RIPv1 and receives RIPv1 and RIPv2. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1306
48 Remote Monitoring (RMON) Dell EMC Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1307
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1308
To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON group of statistics. The integer value must be a unique index in the RMON history table.
PAGE 1309
owner name (OPTIONAL) Enter the keyword owner then the owner name to record the owner of the RMON group of statistics. Defaults none Command Modes CONFIGURATION INTERFACE (config-if) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.
PAGE 1310
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1311
owner string (OPTIONAL) Enter the keyword owner then the owner name to specify an owner for the alarm. This is the alarmOwner object in the alarmTable of the RMON MIB. Defaults owner Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1312
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon RMON status total memory used 218840 bytes.
PAGE 1313
Example (Index) Example (Brief) Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. DellEMC# show rmon alarm 1 RMON alarm entry 1 sample Interval: 5 object: 1.3.6.1.2.1.1.3 sample type: absolute value.
PAGE 1314
show rmon events Display the contents of the RMON event table. S4048–ON Syntax show rmon events [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-toread format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1315
event owner: event status: OK RMON event entry 113 description: event type: SNMP TRAP. event community: private event last time sent: none event owner: event status: OK RMON event entry 114 description: event type: LOG and SNMP TRAP.
PAGE 1316
Example (Index) Example (Brief) Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1317
Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an easy-to-read format Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example (Index) Example (Brief) Version Description 9.10(0.
PAGE 1318
show rmon log Display the contents of the RMON log table. S4048–ON Syntax show rmon log [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON log table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1319
show rmon statistics Display the contents of RMON Ethernet statistics table. S4048–ON Syntax Parameters show rmon statistics [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet statistics table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1320
256-511 bytes packets: 0 512-1023 bytes packets: 0 1024-1518 bytes packets: 0 owner: 1 status: OK HC packets received overflow: 0 HC packets received: 0 HC bytes received overflow: 0 HC bytes received: 0 HC 64bytes packets overflow: 0 HC 64bytes packets: 0 HC 65-127 bytes packets overflow: 0 HC 65-127 bytes packets: 0 HC 128-255 bytes packets overflow: 0 HC 128-255 bytes packets: 0 HC 256-511 bytes packets overflow: 0 HC 256-511 bytes packets: 0 HC 512-1023 bytes packets overflow: 0 HC
PAGE 1321
49 Rapid Spanning Tree Protocol (RSTP) The Dell EMC Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell EMC Networking OS supports RSTP.
PAGE 1322
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol.
PAGE 1323
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Example DellEMC# debug spanning-tree rstp bpdu tengigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree.
PAGE 1324
disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1325
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1326
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information The hello time is encoded in BPDUs in increments of 1/256ths of a second.
PAGE 1327
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • • forward-delay — changes the wait time before RSTP transitions to the Forwarding state. hello-time — changes the time interval between BPDUs. protocol spanning-tree rstp To configure RSTP, enter RSTP mode.
PAGE 1328
Related Commands • disable — disables RSTP globally on the system. show config View the current configuration for the mode. Only non-default values are displayed. Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1329
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1330
Te 4/9 Altr 128.427 128 20000 BLK 20000 P2P DellEMC# Example (EDS, LBK) No NOTE: “LBK_INC” (bold) means Loopback BPDU Inconsistency. DellEMC# show spanning-tree rstp br Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e801.
PAGE 1331
• • • • Port Channel interface with one 10 Gigabit Ethernet = 2000 Port Channel with two 1 Gigabit Ethernet = 18000 Port Channel with two 10 Gigabit Ethernet = 1800 Port Channel with two 100 Mbps Ethernet = 180000 edge-port Enter the keywords edge-port to configure the interface as a rapid spanning tree edge port. bpduguard (OPTIONAL) Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails.
PAGE 1332
Usage Information The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack. This option places the port into an Error Disable state if a BPDU appears and a message is logged so that the administrator can take corrective action. NOTE: A port configured as an edge port, on an RSTP switch, immediately transitions to the Forwarding state.
PAGE 1333
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. Usage Information By default, Dell EMC Networking OS implements an optimized flush mechanism for RSTP.
PAGE 1334
50 Software-Defined Networking (SDN) 1334 Software-Defined Networking (SDN)
PAGE 1335
51 Security The commands in this chapter are available on Dell EMC Networking OS. For configuration details, see the Security section in the Dell EMC Networking OS Configuration Guide. NOTE: Dell EMC Networking OS implements LEAP with MSCHAP v2 supplicant.
PAGE 1336
commands {level | Enter the keyword commands then a privilege level for accounting of commands role role-name} executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: • • For name, enter a user-defined name of a list of accounting methods. For default, the default accounting methods used.
PAGE 1337
Example (TACACS +) DellEMC(conf)# aaa accounting exec default start-stop tacacs+ DellEMC(conf)# aaa accounting command 15 default start-stop tacacs+ DellEMC(conf)# aaa accounting command role secaadmin default start-stop tacacs+ Example (RADIUS) Related Commands DellEMC(conf)# aaa accounting dot1x default start-stop radius DellEMC(conf)# aaa accounting dot1x default stop-only radius • • • • enable password — changes the password for the enable command.
PAGE 1338
Related Commands Version Description 6.3.1.0 Introduced on the E-Series. • aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa accounting suppress Prevent the generation of accounting records of users with the user name value of NULL. Syntax aaa accounting suppress null-username To permit accounting records to users with user name value of NULL, use the no aaa accounting suppress null-username command.
PAGE 1339
Parameters group-name Enter the name of the RADIUS server group. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1340
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1341
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1342
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1343
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the E-Series. Usage Information By default, the aaa authorization commands command configures the system to check both EXEC level and CONFIGURATION level commands.
PAGE 1344
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS. privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands. Syntax privilege mode {level level command | reset command} To delete access to a level and command, use the no privilege mode level level command command.
PAGE 1345
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines. Syntax privilege level level To delete access to a terminal line, use the no privilege level level command.
PAGE 1346
Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication, use the service obscure-passwords command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1347
Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | methodlist-name} method [... method2] command.
PAGE 1348
Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. Usage Information By default, the Enable password is used. If you configure aaa authentication enable default, Dell EMC Networking OS uses the methods defined for Enable access instead. Methods configured with the aaa authentication enable command are evaluated in the order they are configured.
PAGE 1349
Version Description 9.11(0.0) Included a prompt to force the users to re-authenticate, when re-authentication is enabled. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0 Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles Z9500. 9.5(0.
PAGE 1350
To disable the re-authentication option, use the no aaa reauthenticate enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced this command.
PAGE 1351
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. • • • line — applies an authentication method list to the designated terminal lines.
PAGE 1352
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1353
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1354
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1355
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.6.0.0 Revised introductory and usage guidelines description. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.
PAGE 1356
Version Description 9.13(0.0) Changed the maximum length of the password from 32 to 96. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1357
user-lockoutperiod minutes (OPTIONAL) Enter the keyword user-lockout-period then the number of minutes. The range is from 1 to 1440 minutes. The default is 0 minutes and the lockout-period is not enabled. This parameter enhances the security of the switch by locking out the local user account if there are more number of unsuccessful login attempts than what is configured using the max-retry parameter. The default value is 3 times.
PAGE 1358
Example In the following example, after 5 un-successful login attempts, the session (SSH/TELNET) goes into a locked state for 5 minutes. If all the 10 sessions are locked out with 5 un-successful attempts in each session, no users can login during the lockout-period. DellEMC(conf)# password-attributes max-retry 5 lockout-period 5 Related Commands • password — specifies a password for users on terminal lines. secure-cli enable Enable the secured CLI mode.
PAGE 1359
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security. When the passwords are encrypted, you cannot return them to plain text unless you re-configure them.
PAGE 1360
Example DellEMC# show privilege Current privilege level is 15. DellEMC# DellEMC# show privilege Current privilege level is 14. DellEMC# DellEMC# show privilege Current privilege level is 10. DellEMC# Related Commands • privilege level (CONFIGURATION mode) — assign access control to different command modes. show users Allows you to view information on all users logged in to the switch. Syntax show users [all] Parameters all (OPTIONAL) Enter the keyword all to view all terminal lines in the switch.
PAGE 1361
Field Description User Displays the user name of all users logged in. Host(s) Displays the terminal line status. Location Displays the IP address of the user. Example Related Commands DellEMC# show users Authorization Mode: role or privilege Line User Host(s) Location * 0 console 0 2 vty 0 admin idle 10.16.127.35 3 vty 1 ad idle 10.16.127.145 4 vty 2 ad1 idle 10.16.127.141 5 vty 3 ad1 idle 10.16.127.145 6 vty 4 admin idle 10.16.127.141 7 vty 5 ad idle 10.16.127.
PAGE 1362
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information The software measures the period of inactivity defined in this command as the period between consecutive keystrokes.
PAGE 1363
Defaults The default encryption type for password option is 0. The default encryption type for secret option is 5. The default encryption type for sha256-password option is 8. The default value of privilege level is 1. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(1.0) Introduced dynamic-salt option on the S4810 and S4820T. 9.
PAGE 1364
RADIUS Commands The following RADIUS commands are supported by Dell EMC Networking OS. aaa radius auth-method Configure the authentication method to use with RADIUS for user access. Syntax aaa radius auth-method {pap | mschapv2} To undo the RADIUS authentication method configuration, use the no aaa radius auth-method command. Parameters pap Enter the keyword pap to use the Password Authentication Protocol (PAP) for RADIUS authentication.
PAGE 1365
key Command Modes • Usage Information • Command History Enter a string that is the key to be exchanged between the switch and the dynamic authorization client. The key can be up to 42 characters long. CONF-DYNAMIC-AUTH It is possible to configure more than one dynamic authorization clients Duplicate (ipv4-addr or ipv6-addr or host-name) configurations are not allowed. This guide is platform-specific.
PAGE 1366
Command Modes • Usage Information • Command History CONF-DYNAMIC-AUTH Configure no coa-bounce-port to drop radius CoA port-bounce requests from the DAC. This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1367
debug radius View RADIUS transactions to assist with troubleshooting. Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1368
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010– ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. disconnect-user Configure NAS to allow or reject DM requests corresponding to AAA users-sessions coming from the DAC. Syntax disconnect-user To undo this configuration, enter the no disconnect-user command. Defaults Enabled.
PAGE 1369
Parameters interface Enter the following keywords and the interface information: • • • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. For a port channel interface, enter the keywords port-channel then a number.
PAGE 1370
Usage Information • Command History Optionally specify dynamic authorization port number. Default port is 3799. This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command. Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.
PAGE 1371
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1372
radius-server host 1.1.1.1 key 7 9a2f3ec0c65c6f41 radius-server host 2.2.2.2 key 7 9a2f3ec0c65c6f41 DellEMC(conf-radius-group)# Related Commands • • • • login authentication — sets the database to be checked when a user logs in. radius-server key — sets an authentication key for RADIUS communications. radius-server retransmit — sets the number of times the RADIUS server attempts to send information. radius-server timeout — sets the time interval before the RADIUS server times out.
PAGE 1373
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1374
radius-server vrf Create an association between a RADIUS server group and a VRF and source interface. ud Syntax radius-server vrf vrf-name [source-interface interface] To delete the association between a RADIUS server group and a VRF and source interface, use the no radiusserver vrf vrf-name [source-interface interface] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a RADIUS server group with that VRF.
PAGE 1375
Example DellEMC(conf)#radius-server group group1 DellEMC(conf-radius-group)#radius-server vrf vrf1 source-interface tengigabitethernet 1/40 DellEMC(conf)#radius-server group group2 DellEMC(conf-radius-group)#radius-server vrf default radius-server key Configure a key for all RADIUS communications between the switch and the RADIUS host server. Syntax radius-server key [encryption-type] key To delete a password, use the no radius-server key command.
PAGE 1376
If you configure the key parameter in the radius-server host command, the key configured with the radius-server key command is the default key for all RADIUS communications. Related Commands • radius-server host — configures a RADIUS host. radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable.
PAGE 1377
To return to the default value, use the no radius-server timeout command. Parameters seconds Enter the number of seconds between an unsuccessful attempt and the Dell EMC Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds. Defaults 5 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1378
Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.13(0.0) Introduced on the C9010, S3100, S3048–ON, S4048T-ON, S4048–ON, S5000, S6010– ON, S6000–ON, S6100–ON, S6000, Z9100–ON, Z9500, FN-IOM, and MXL. replay-protection-window Configure replay protection window period to drop the duplicate packets. Syntax replay-protection-window minutes To undo the configuration, enter the no replay-protection-window command. Defaults Parameters Command Modes 5 Minutes.
PAGE 1379
TACACS+ Commands Dell EMC Networking OS supports TACACS+ as an alternate method for login authentication. tacacs-server group Creates a group of TACACS servers to be used for Authentication, Authorization, and Accounting.. Syntax aaa tacacsgroup group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command . Parameters group-name Enter the name of the TACACS server group. Defaults Not configured.
PAGE 1380
Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1381
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.
PAGE 1382
Example Related Commands DellEMC(conf)# tacacs-server group group1 DellEMC(conf-tacacs-group)# tacacs-server host 1.1.1.1 key secret DellEMC(conf-tacacs-group)# tacacs-server host 2.2.2.2 key secret DellEMC(conf-tacacs-group)# tacacs-server vrf vrf1 source-interface tengigabitethernet 1/42 DellEMC(conf-tacacs-group)# show config ! tacacs-server group group1 tacacs-server vrf vrf1 source-interface TenGigabitEthernet 1/42 tacacs-server host 1.1.1.1 key 7 9a2f3ec0c65c6f41 tacacs-server host 2.2.2.
PAGE 1383
Version Description 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times.
PAGE 1384
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1385
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1386
• The 802.1X with VLAN assignment feature is not supported on trunk ports, dynamic ports, or with dynamic-access port assignment through a VLAN membership. dot1x authentication (Configuration) Enable dot1x globally; dot1x must be enabled both globally and at the interface level. Syntax dot1x authentication To disable dot1x on globally, use the no dot1x authentication command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1387
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1388
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. Usage Information If the host responds to 802.1X with an incorrect login/password, the login fails. The switch attempts to authenticate again until the maximum attempts configured is reached. If the authentication fails after all allowed attempts, the interface is moved to the authentication failed VLAN.
PAGE 1389
To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port[/subport]) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1390
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1391
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. • interface range — configure a range of interfaces. dot1x port-control Enable port control on an interface.
PAGE 1392
dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command. Parameters seconds Enter the number of seconds. The range is from 1 to 65535. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1393
Related Commands Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1394
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant.
PAGE 1395
Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON.
PAGE 1396
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. show dot1x interface Display the 802.1X information on an interface.
PAGE 1397
Example Version Description 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. DellEMC#show dot1x interface fortyGigE 1/48 802.
PAGE 1398
crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell EMC Networking representative. crypto key generate {rsa} Parameters rsa Enter the keyword rsa then the key size to generate a SSHv2 RSA host keys. The range is from 1024 to 2048 if you did not enable FIPS mode; if you enabled FIPS mode, you can only generate a 2048-bit key. The default is 1024.
PAGE 1399
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! DellEMC(conf)# Related Commands • • ip ssh server — enables the SSH server. show crypto — displays the SSH host public keys. crypto key zeroize rsa Removes the generated RSA host keys and zeroize the key storage location. Syntax crypto key zeroize rsa Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1400
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1401
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command. Related Commands • ip ssh server — enables the SSH and SCP server on the switch. ip ssh authentication-retries Configure the maximum number of attempts that should be used to authenticate a user. Syntax Parameters ip ssh authentication-retries 1-10 1-10 Enter the number of maximum retries to authenticate a user.
PAGE 1402
To disable the challenge response authentication, use the no ip ssh challenge-responseauthentication enable command. Parameters enable Enter the keyword enable to enable the challenge response authentication for SSHv2. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1403
ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server. Syntax ip ssh hostbased-authentication enable To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbased-authentication enable command. Parameters enable Enter the keyword enable to enable hostbased-authentication for SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1404
Parameters 512-869 Enter the key-size number for the server-generated RSA SSHv1 key. The range is from 512 to 869. The default is 768. Defaults Key size 768 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1405
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information With password authentication enabled, you can authenticate using the local, RADIUS, or TACACS+ password fallback order as configured.
PAGE 1406
Usage Information This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command once. The file contains the OpenSSH-compatible public keys of the host for which host-based authentication is allowed.
PAGE 1407
ip ssh rhostsfile Specify the rhost file used for host-based authorization. Syntax Parameters ip ssh rhostsfile {WORD} WORD Enter the rhost file name for the host-based authentication. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1408
Parameters enable Enter the keyword enable to enable RSA authentication for the SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1409
• • aes192-ctr aes256-ctr The default cipher list is used. • • • • • • • mac hmacalgorithm 3des-cbc aes128-cbc aes192-cbc aes256-cbc aes128-ctr aes192-ctr aes256-ctr Enter the keyword mac then a space-delimited list of hash message authentication code (HMAC) algorithms supported by the SSH server for keying hashing for the message authentication. The following HMAC algorithms are available: • • • hmac-sha1 hmac-sha1-96 hmac-sha2-256 When FIPS is enabled, the default HMAC algorithm is hmac-sha1-96.
PAGE 1410
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Removed support for SSHv1 from all platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Removed the support for hmac-sha2-256-96 algorithm. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1411
Version Description 9.13.0.1 Introduced on the MXL, C9010, S3048–ON, S3100 series, S4810, S4820T, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6100–ON, S6010–ON, Z9500, Z9100–ON and FN-IOM. Usage Information To disable the DNS in SSH server configuration, use the no ip ssh server dns enable command. ip ssh server vrf Configure an SSH server on either a specific VRF or a management VRF. Syntax NOTE: Some of the parameters in this command require licensing to access.
PAGE 1412
• • Related Commands • DellEMC(conf)# ip ssh server vrf management DellEMC(conf)# no ip ssh server vrf show ip ssh — displays the ssh information. ip ssh source-interface Specifies an interface’s IP address as the source IP address for an outgoing SSH connections. Syntax ip ssh source-interface interface To delete a source interface, use the no ip ssh source-interface command.
PAGE 1413
ip ssh vrf Specify a VRF for an outgoing SSH connections. Syntax ip ssh vrf vrf-name To delete a VRF for an outgoing SSH connection, use the no ip ssh vrf vrf-name command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to configure that VRF for an outgoing SSH session. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1414
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.12(0.0) Removed support for rsa1 keys from all platforms. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1415
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Removed the support for hmac-sha2-256-96 algorithm. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1416
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1417
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1418
configured using the ip ssh source-interface command and the ssh vrf vrf-name command, then an error is reported. hostname (OPTIONAL) Enter the IP address or the host name of the remote device. vrf instance (OPTIONAL) E-Series Only: Enter the keyword vrf then the VRF Instance name to open an SSH connection to that instance. ipv4 address (OPTIONAL) Enter the IP address in dotted decimal format A.B.C.D.
PAGE 1419
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for the following ciphers and HMAC alogorithms on the Z9000, S6000, S4820T, S4820T. S6000–ON. • • • • • • • • aes128-cbc aes192-cbc aes256-cbc aes128-ctr aes192-ctr aes256-ctr hmac-sha2-256 hmac-sha2-256-96 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1420
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1421
Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1422
Parameters mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected.
PAGE 1423
Parameters minutes The range is from 5 to 21600. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(1.0) Introduced on the Z9500. 8.3.19.
PAGE 1424
ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1425
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping vlan Enable DHCP Snooping on one or more VLANs. Syntax Parameters [no] ip dhcp snooping vlan name name Enter the name of a VLAN on which to enable DHCP Snooping. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1426
Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands EXEC EXEC Privilege Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1427
inherit existingrole-name Enter the inherit keyword then specify the system defined role to inherit permissions from (sysadmin, secadmin, netadmin, netoperator). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1428
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 1429
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1430
Version Description 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL Examples DellEMC# show role mode configure username Role access: sysadmin DellEMC# show role mode configure management route Role access: netadmin, sysadmin DellEMC# show role mode configure management crypto-policy Role access: secadmin, sysadmin Related Commands • userrole — create user roles. show userroles Display information on all defined user roles.
PAGE 1431
sysadmin netoperator testadmin Related Commands • Exec Config Interface Line Router IP Route-map Protocol MAC netadmin Exec Config Interface Line Router IP Route-map Protocol MAC userrole — create user roles. userrole Create user roles for the role-based security model. Syntax userrole name inherit existing-role-name To delete a role name, use the no userrole name command. Note that the reserved role names may not be deleted.
PAGE 1432
• Make sure you select the correct role you want to inherit. NOTE: If you inherit a user role, you cannot modify or delete the inheritance. If you want to change or remove the inheritance, delete the user role and create it again. If the user role is in use, you cannot delete the user role. role mode { { { addrole | deleterole } role-name } | reset } command – Modifies (adds or deletes) command permissions for newly created user roles and system defined roles.
PAGE 1433
ICMPv6 Message Types Echo reply (129) Who are you request (139) Who are you reply (140) Mtrace response (200) Mtrace messages (201) NOTE: The Dell EMC Networking OS does not suppress the following ICMPv6 message types: • Packet too big (2) • Echo request (128) • Multicast listener query (130) • Multicast listener report (131) • Multicast listener done (132) • Router solicitation (133) • Router advertisement (134) • Neighbor solicitation (135) • Neighbor advertisement (136) • Redirect (137
PAGE 1434
boot-access password Set a password for the boot loader. Syntax boot-access password [encryption-type] boot-password To remove the GRUB access password, use the no boot-access password command. Parameters encryption-type (OPTIONAL) Enter an encryption type for the boot password. • • boot-password Defaults None Command Modes CONFIGURATION. Command History 0 directs the system to store the password as clear text. 7 directs the system to store the password with a dynamic salt.
PAGE 1435
flash://filename Enter the keyword flash: and enter the filename to generate the hash checksum for any file in the flash drive using the MD5, SHA1, or SHA256 algorithm. startup-config Enter the keyword shartup-config to generate the hash checksum for the startup configuration using the MD5, SHA1, or SHA256 algorithm. Defaults None Command Modes EXEC Privilege Command History Version Description 9.14(1.0) Introduced on the S4810 and S4820T. 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.
PAGE 1436
• • • A minimum of one upper case letter (A to Z) A minimum of one numeric character (0 to 9) A minimum of one special character including a space (" !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~") If your password does not meet the criteria, the system does not accept your password. If you use encryption type 9, the system stores the clear text password in an inaccessible location on the system. The show running-configuration command does not display the password.
PAGE 1437
Version Description 9.14(0.0) Introduced on the S5048F–ON. 9.13(0.0) Introduced on the S3100 series, S3048–ON, S4048–ON, S4048T-ON, S5000, S6000, S6000–ON, S6010–ON, S6100–ON, Z9100–ON, Z9500, C9010, MXL, and FN-IOM. Usage Information Dell EMC Networking OS supports MD5, SHA1, and SHA256. Example DellEMC# verified boot hash system-image A: 619A8C1B7A2BC9692A221E2151B9DA9E verified startup-config Enable hash validation for the startup configuration during system startup.
PAGE 1438
52 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell EMC Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell EMC Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell EMC Networking OS supports L2PT on Dell EMC Networking OS.
PAGE 1439
count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Defaults Debug disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1440
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.1 Added support for 802.1X, E-LMI, GMRP, GVRP, LLDP, LACP, MMRP, MVRP, and OAM 802.3ah protocol traffic to the E-Series. 8.2.1.
PAGE 1441
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command • show protocol-tunnel — displays tunneling information for all VLANs. protocol-tunnel enable Enable protocol tunneling globally on the system.
PAGE 1442
Parameters rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. Defaults 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.
PAGE 1443
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1444
53 sFlow The Dell EMC Networking OS supports sFlow commands. The Dell EMC Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1445
To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command. Parameters sflow collector ipaddress | ipv6- address Enter the IP address of the collector in dotted decimal format for IPv4 or x:x:x:x::x format for IPv6. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1446
Version Description 6.2.1.1 Introduced on the E-Series. Usage Information You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both. The sFlow agent address is carried in a field in SFlow packets and is used by the collector to identify the sFlow agent. In sFlow, the agent address is a single invariant IPv4 or IPv6 address used to identify the agent to the collector.
PAGE 1447
Version Description 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired. Related Commands • sflow enable (Interface) — enable sFlow on interfaces. sflow enable (Interface) Enable sFlow egress on interfaces. Syntax sflow enable To disable sFlow, use the no sflow enable command. Defaults Disabled.
PAGE 1448
Usage Information When you enable ingress sFlow on an interface, flow sampling is done on any incoming traffic. NOTE: After a physical port is a member of a LAG, it inherits the sFlow configuration from the LAG port. Related Commands • sflow enable (Global) — turn sFlow globally. sflow extended-switch enable Enable packing information on a switch only. Syntax sflow extended-switch enable To disable packing information, use the no sflow extended-switch [enable] command.
PAGE 1449
sflow max-header-size extended Set the maximum header size of a packet to 256 bytes. Syntax sflow max-header-size extended To reset the maximum header size of a packet, use the[no] sflow max-header-size extended command. Parameters extended Defaults 128 bytes Command Modes CONFIGURATION Enter the keyword extended to copy 256 bytes from the sample packets to sFlow datagram. INTERFACE Command History Example This guide is platform-specific.
PAGE 1450
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.
PAGE 1451
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1452
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This command changes the global default sampling rate. You can configure an interface to use a different sampling rate than the global sampling rate.
PAGE 1453
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command changes the sampling rate for an interface. By default, the sampling rate of an interface is set to the same value as the current global default sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power-of-2 value.
PAGE 1454
Version Description 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information The dropEvent counter (sFlow samples dropped due to sub-sampling) shown in the following example always displays a value of zero.
PAGE 1455
54 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell EMC Networking OS. Topics: • • SNMP Commands Syslog Commands SNMP Commands The following SNMP commands are available in the Dell EMC Networking OS.
PAGE 1456
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1457
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1458
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The following Example displays a group named ngroup. The ngroup has a security model of version 3 (v3) with authentication (auth), the read and notify name is nview with no write view name specified, and finally the row status is active.
PAGE 1459
RADIUS-AUTH-CLIENT-MIB SNMP-MPD-MIB RMON-MIB --More— 1.3.6.1.2.1.67.1.2 1.3.6.1.6.3.11 1.3.6.1.2.1.16 show snmp supported-traps Display the list of SNMP traps supported by the platform. Syntax show snmp supported-traps Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.14(0.
PAGE 1460
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1461
snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.
PAGE 1462
name name] | access-list-name [ipv6 ipv6-access-list-name | access-list-name | security-name name]]] To remove access to a community, use the no snmp-server community community-string {ro | rw} [security-name name [access-list-name | ipv6 access-list-name | accesslist-name ipv6 access-list-name]] command. Parameters community-name Enter a text string (up to 20 characters long) to act as a password for SNMP. ro Enter the keyword ro to specify read-only permission.
PAGE 1463
If you do not configure the snmp-server community command, you cannot query SNMP data. Only Standard IPv4 ACL and IPv6 ACL is supported in the optional access-list-name. The command options ipv6, security-name, and access-list-name are recursive. In other words, each option can, in turn, accept any of the three options as a sub-option, and each of those sub-options can accept any of the three sub-options as a sub-option, and so forth.
PAGE 1464
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps. Syntax snmp-server enable traps [notification-type] [notification-option] To disable traps, use the no snmp-server enable traps [notification-type] [notificationoption] command.
PAGE 1465
Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for copy-config and ECMP traps. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for VRRP traps. 7.6.1.0 Added support for STP and xSTP traps. Introduced on the S-Series. 7.5.1.
PAGE 1466
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1467
• • • 1 is the least secure version. 3 is the most secure of the security modes. 2c allows transmission of informs and counter 64, which allows for integers twice the width of what is normally allowed. The default is 1. auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. noauth (OPTIONAL) Enter the keyword noauth to specify no authentication of a packet.
PAGE 1468
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The following example specifies the group named harig as a version 3 user requiring both authentication and encryption and read access limited to the read named rview. NOTE: The number of configurable groups is limited to 16 groups.
PAGE 1469
priv (OPTIONAL) Enter the keyword priv to specify both authentication and then scrambling of the packet. community-string Enter a text string (up to 20 characters long) as the name of the SNMP community. NOTE: For version 1 and version 2c security models, this string represents the name of the SNMP community. The string can be set using this command; however, Dell EMC Networking OS recommends setting the community string using the snmp-server community command before executing this command.
PAGE 1470
Version Description 9.1(0.0) Added support for config and ecmp traps. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for VRRP traps. 7.6.1.0 Added support for STP and xSTP notification types. Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To configure the router to send SNMP notifications, enter at least one snmp-server host command.
PAGE 1471
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1472
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server trap-source Configure a specific interface as the source for SNMP traffic.
PAGE 1473
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810 8.5.1.0 Added support for 4-port 40G line cards. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To enable this snmp-server trap-source command, configure an IP address on the interface and enable the interface configured as an SNMP trap source. Related Commands • snmp-server community — sets the community string.
PAGE 1474
auth (OPTIONAL) Enter the keyword auth to specify authentication of a packet without encryption. md5 | sha (OPTIONAL) Enter the keyword md5 or sha to designate the authentication level. • • md5 — Message Digest Algorithm sha — Secure Hash Algorithm auth-password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the agent to receive packets from the host. Minimum: eight characters long.
PAGE 1475
Usage Information NOTE: For IPv6 ACLs, only IPv6 and UDP types are valid for SNMP. TCP and ICMP rules are not valid for SNMP. In IPv6 ACLs port rules are not valid for SNMP. No default values exist for authentication or privacy algorithms and no default password exists. If you forget a password, you cannot recover it; the user must be reconfigured. You can specify either a plain-text password or an encrypted cypher-text password.
PAGE 1476
Defaults If no authentication or privacy option is configured, then the messages are exchanged (attempted anyway) without any authentication or encryption. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 1477
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1478
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information Use this command to bind an SNMP agent to a VRF. The SNMP agent processes the requests from the interfaces that belong to the specified VRF. If no VRF is specified, then the default VRF is used.
PAGE 1479
Syslog Commands The following commands allow you to configure logging functions on all Dell EMC Networking switches. clear logging Clear the messages in the logging buffer. Syntax clear logging Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1480
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Introduced on the FN IOM. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the MXL.
PAGE 1481
Related Commands • logging buffered — set the logging buffered parameters. default logging console Return the default settings for messages logged to the console. Syntax default logging console Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.
PAGE 1482
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1483
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • logging trap — limit messages logged to the Syslog servers based on severity. logging Configure an IP address or host name of a Syslog server where logging messages are sent. Multiple logging servers of both IPv4 and/or IPv6 can be configured.
PAGE 1484
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for IPv6. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1485
Version Description 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you decrease the buffer size, all messages stored in the buffer are lost.
PAGE 1486
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • • • clear logging — clears the logging buffer. default logging console — returns the logging console parameters to the default setting.
PAGE 1487
Examples Related Commands DellEMC(conf)#logging extended • • show logging auditlog — display the audit log. clear logging auditlog— clear the audit log. logging facility Configure the Syslog facility used for error messages sent to Syslog servers. Syntax logging facility [facility-type] To return to the default values, use the no logging facility command.
PAGE 1488
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1489
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network management station. Related Commands • show logging — displays information logged to the history buffer.
PAGE 1490
Related Commands • show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications. Syntax logging monitor [level] To disable logging to terminal connections, use the no logging monitor command. Parameters level Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1491
To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.
PAGE 1492
• • • For a port-channel interface, enter the keywords port-channel then the portchannel ID. For a Null interface, enter the keyword null then the Null interface number. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1493
all Enter the keyword all to turn off all. limit number-ofbuffers Enter the keyword limit then the number of buffers to be queued for the terminal after which new messages are dropped. The range is from 20 to 300. The default is 20. Defaults Disabled. If enabled without the level or number-of-buffers options specified, level = 2 and number-ofbuffers = 20 are the defaults. Command Modes LINE Command History This guide is platform-specific.
PAGE 1494
Defaults 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1495
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. Usage Information To display syslog messages in a RFC 3164 or RFC 5424 format, use the log version command in configuration mode. By default, the system log version is set to 0.
PAGE 1496
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1497
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1498
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 1499
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1500
55 SNMP Traps This section lists the traps sent by the Dell EMC Networking OS. Each trap is listed by the fields Trap Type, Trap Name, Object Name, and MIB file. Table 9. SNMP Trap List TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 1 TR_COLD_START 1.3.6.1.6.3.1.1.5.1 COLDSTART rfc3418.mib SNMP COLD_START trap sent. 2 TR_WARM_START 1.3.6.1.6.3.1.1.5.2 WARMSTART rfc3418.mib SNMP WARM_START trap sent. 3 TR_LINK_DOWN 1.3.6.1.6.3.1.1.5.3 LINKDOWN rfc3418.
PAGE 1501
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation RPM or the secondary RPM is up and running. 20 TR_CHM_RPM_DO 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmRpm DELLWN .5.1.6 Down NETWORKINGCHASSIS-MIB.mib The primary RPM generate this trap when the secondary RPM is down, either by software reset or being physically removed from the chassis. 21 TR_CHM_PWRSRC 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmPow DELL_DOWN .5.1.7 ersupplyDown NETWORKINGCHASSIS-MIB.
PAGE 1502
TRAP TYPE TRAP NAME TRAP OID Object Name 30 TR_CHM_FANTRAY 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmFanT DELL_OR_PSU_BAD .5.1.25 rayOrPsuDown NETWORKINGCHASSIS-MIB.mib The driver/agent generate this trap when a fan tray or psu is missing or down. 31 TR_CHM_FANTRAY 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmFanT DELL_OR_PSU_BAD_CL .5.1.26 rayOrPsuClear NETWORKINGR CHASSIS-MIB.mib The driver/agent generate this trap when a fan tray or psu is now operational 32 TR_CHM_PSUFAN_ 1.3.6.1.4.1.6027.3.26.
PAGE 1503
TRAP TYPE TRAP NAME 49 TRAP OID Object Name MIB File Explanation TR_PVST_NEW_RO 1.3.6.1.2.1.17.0.1 OT newRoot BRIDGE-MIB.mib PVST new root trap support. 50 TR_PVST_TOPOLO 1.3.6.1.2.1.17.0.2 GY_CHANGE topologyChange BRIDGE-MIB.mib PVST topology change trap support. 51 TR_VRRP_LEAVE_ MASTER 52 TR_VRRP_GIVEUP_ 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmVrrp DELLMASTER .5.1.45 GiveupMaster NETWORKINGCHASSIS-MIB.
PAGE 1504
TRAP TYPE TRAP NAME TRAP OID 59 TR_BGP4_ESTABLI SHED 1.3.6.1.4.1.6027.20.1.1. dellNetBgpM2Establi DELL0.1 shed NETWORKINGBGP4-V2-MIB.mib The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state 60 TR_BGP4_BACKW_ 1.3.6.1.4.1.6027.20.1.1. dellNetBgpM2Backw DELLXSITION 0.2 ardTransition NETWORKINGBGP4-V2-MIB.mib The BGPBackwardTransi tion Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.
PAGE 1505
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation the MEP's Maintenance Domain table entry (dot1agCfmMdTable ). dot1agCfmMaIndex - Also an index (with the MD table index) of the MEP's Maintenance Association table entry (dot1agCfmMaTable) . dot1agCfmMepIdenti fier - MEP Identifier and final index into the MEP table (dot1agCfmMepTabl e). 62 TR_EOAM_THRSHL 1.3.6.1.2.1.158.0.1 D_EVT dot3OamThresholdE stdeoam.
PAGE 1506
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 63 TR_EOAM_NON_T HRSHLD_EVT 1.3.6.1.2.1.158.0.2 dot3OamNonThresh oldEvent stdeoam.mib A dot3OamNonThresh oldEvent notification is sent when a local or remote nonthreshold crossing event is detected. A local event is detected by the local entity, while a remote event is detected by the reception of an Ethernet OAM Event Notification OAMPDU that indicates a nonthreshold crossing event.
PAGE 1507
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation FIPSNOOPINGMIB.mib discovered (Discovery Advertisement is received from FCF) is dropped, as the maximum allowed FCFs limit in a VLAN is already reached. 68 TR_FIPS_ENODE_D 1.3.6.1.4.1.6027.3.22. ROP 4.0.5 dellNetENodeDroppe DELLdTrap NETWORKINGFIPSNOOPINGMIB.mib This trap is sent when a new ENode discovered is dropped, as the maximum allowed ENodes limit in the system is already reached 69 TR_FIPS_SESSION_ 1.3.6.1.4.1.6027.3.22.
PAGE 1508
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation change in the DCBX Peer Status and the dellNetETSGlobalEna bleTrap is enabled to send the trap for Peer Up or Peer Down 74 TR_ETS_OPER_ST ATE_CHANGE 1.3.6.1.4.1.6027.3.15.4 dellNetETSPortDcbx DELL.0.4 OperStateTrap NETWORKINGDCB-MIB.mib This trap is generated in the following conditions.
PAGE 1509
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 78 TR_PFC_OPER_ST ATE_CHANGE 1.3.6.1.4.1.6027.3.15.4 dellNetPFCPortDcbx DELL.0.8 OperStateTrap NETWORKINGDCB-MIB.mib 79 TR_MPLS_TUNNEL 1.3.6.1.2.1.10.166.3.0.1 mplsTunnelUp _UP rfc3812.mib This trap is generated when an lsp on a tunnel changed it operational status to up 80 TR_MPLS_TUNNEL 1.3.6.1.2.1.10.166.3.0. _DOWN 2 mplsTunnelDown rfc3812.
PAGE 1510
TRAP TYPE TRAP NAME 94 TR_SYSADM_CPU_ 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmExd THRESHOLD .5.1.31 CpuThreshold 95 TR_SYSADM_CPU_ 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmClrC DELLTHRESHOLD_CLR .5.1.32 puThreshold NETWORKINGCHASSIS-MIB.mib The agent generate this trap when cpu utilization falls below threshold. 96 TR_SYSADM_MEM _THRESHOLD 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmExd .5.1.33 MemThreshold The agent generate this trap when memory utilization excceded 92%.
PAGE 1511
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation local device sensinga change in the topology that indicates that a new remotedevice attached to a local port, or a remote device disconnectedor moved from one port to another 104 TR_OPENFLOW_S 1.3.6.1.4.1.6027.3.20. NMP_CNTLR_STAT 2.0.1 E_TRAP ofSwitchCntlrSessio nStatusChanged DELLNETWORKINGOPENFLOWMIB.mib This notification is sent when ever Controller's Session Status has changed 105 TR_OPENFLOW_S 1.3.6.1.4.1.6027.3.20.
PAGE 1512
TRAP TYPE TRAP NAME 109 TR_RMON_HC_FAL 1.3.6.1.2.1.16.29.2.0.2 hcFallingAlarm LING_THRESHOLD 110 TR_COPY_CONFIG _COMPLETE 1.3.6.1.4.1.6027.3.5.1. 2.0.1 copyConfigComplete DELLd NETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a copy operational is completed 111 TR_CONFIG_CONF LICT 1.3.6.1.4.1.6027.3.5.1. 2.0.2 configConflict DELLNETWORKINGCOPY-CONFIGMIB.mib The agent generate this trap when a configuration conflict found during audit. 112 TR_CONFIG_CONF LICT_CLEAR 1.3.6.1.4.1.
PAGE 1513
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 118 TR_CAM_IS_FULL 1.3.6.1.4.1.6027.3.7.1. 2.0.2 camIsFull DELLNETWORKINGSYSTEMCOMPONENTMIB.mib The agent generate this trap when the cam is fully used. 119 TR_CAM_AUDIT_E RROR 1.3.6.1.4.1.6027.3.7.1. 2.0.3 camAuditError DELLNETWORKINGSYSTEMCOMPONENTMIB.mib The agent generate this trap when a cam entry mismatches with the Software entry 128 TR_VLT_ROLE_CH ANGE 1.3.6.1.4.1.6027.3.17.2 dellNetVLTRoleChan DELL.0.
PAGE 1514
TRAP TYPE TRAP NAME 131 TR_VLT_HBEAT_ST 1.3.6.1.4.1.6027.3.17.2 dellNetVLTHBeatSta DELLATUS_CHANGE .0.4 tusChange NETWORKINGVIRTUAL-LINKTRUNK-MIB.mib The agent generates this notification to denote the change in Backup Link Status. The notification contains information on the new BackupLink Status. The possible states are as follows: 1. NotEstabished 2. LinkUp 3. LinkDown 4. LinkError" 132 TR_VLT_ICL_BW_T 1.3.6.1.4.1.6027.3.17.2 dellNetVLTIclBwUsa HRESHOLD_EXCEE .0.
PAGE 1515
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation notification contains the information on the port which has gone through the state change and the oper state information of the actor and its partner 138 TR_ENT_CONFIG_ CHANGE 1.3.6.1.2.1.47.2.0.1 entConfigChange entity.mib An entConfigChange notification is generated when the value of entLastChangeTime changes. It can be utilized by an NMS to trigger logical/ physical entity table maintenance polls.
PAGE 1516
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation to detect any missed entConfigChange notificationevents, e.g., due to throttling or transmission loss. 139 TR_CHM_STACK_U 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmStac DELLNIT_ROLE .5.1.46 kUnitRoleChanged NETWORKINGCHASSIS-MIB.mib Trap generated when a stack unit's role in a stack changes to management/ standby/member 140 TR_CHM_VERSION 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmCard DELL_MISMATCH .5.1.
PAGE 1517
TRAP TYPE TRAP NAME TRAP OID Object Name MIB File Explanation 148 TR_BRM_PE_UNIT _DOWN 1.3.6.1.4.1.6027.3.26.1 dellNetSysAlarmPEU DELL.5.1.30 nitDown NETWORKINGCHASSIS-MIB.mib 149 TR_SYSLOG_SERV 1.3.6.1.4.1.6027.3.30.1 Not Available ER_CONNECTION_ .1.2 SUCCESSFUL Not Available Connecting to server with Valid configuration. 150 TR_SYSLOG_SERV 1.3.6.1.4.1.6027.3.30.1 Not Available ER_CONNECTION_ .1.1 FAILURE Not Available Not able to connecting with server with Invalid configuration.
PAGE 1518
56 Stacking All commands in this chapter are specific to the Dell EMC Networking OS. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, see the Stacking S-Series Switches section in the Dell EMC Networking OS Configuration Guide. CAUTION: You cannot enable stacking simultaneously with virtual link trunking (VLT).
PAGE 1519
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the members option. Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the runningconfig. Related Commands show redundancy — displays the current redundancy status.
PAGE 1520
redundancy protocol Enable hitless failover for a protocol. Syntax redundancy protocol Protocols lacp Enter the LACP protocol xstp Enter one of the following protocols: STP, RSTP, MSTP, PVST. Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1521
Version Description 8.3.1.0 Added the hard reset option. Usage Information Resetting the management unit is not allowed, and an error message displays if you try to do so. Resetting is a soft reboot, including flushing the forwarding tables. Starting with Dell EMC Networking OS version 7.8.1.0, you can run this command directly on the stack standby unit (standby master) to reset the standby. You cannot reset any other unit from the standby unit.
PAGE 1522
• • • The hardware watchdog command is enabled only when the S4048T-ON act as master. As a single image runs on both the S4048T-ON as well as the S4048–ON, the hardware watchdog command is retained on the S4048-ON also. However, this command remains ineffective and does not perform any function when the S4048-ON acts as master. When the S4048T-ON is the master and mixed-mode stacking is disabled, the S4048-ON remains in the card problem state due to type mismatch.
PAGE 1523
unmounting /boot (/dev/wd0b)... unmounting /usr (mfs:29)... unmounting /force10 (mfs:24)... unmounting /lib (mfs:21)... unmounting /f10 (mfs:18)... unmounting /tmp (mfs:9)... unmounting /kern (kernfs)... unmounting / (/dev/md0a)... done rebooting... Example (S4048– ON) Dell#conf t Dell(conf)#mixed-mode-stacking enable Dell#conf t Dell(conf)#no mixed-mode-stacking enable show redundancy Display the current redundancy configuration (status of automatic reboot configuration on stack management unit).
PAGE 1524
-----------------------------------------------Stack-unit State: Standby Peer Stack-unit ID: 2 Stack-unit SW Version: 1-0(0-4812) -- Stack-unit Redundancy Configuration ------------------------------------------------Primary Stack-unit: mgmt-id 1 Auto Data Sync: Full Failover Type: Hot Failover Auto reboot Stack-unit: Enabled Auto failover limit: 3 times in 60 minutes -- Stack-unit Failover Record ------------------------------------------------Failover Count: 0 Last failover timestamp: None Last failover R
PAGE 1525
Version Description 8.3.11.1 Introduced on the Z9000. Usage Information The following describes the show system stack-ports command shown in the following example. Example Example (Status) Field Description Topology Lists the topology of stack ports connected: Ring, Daisy chain, or Standalone. Interface The unit/port ID of the connected stack port on this unit. Link Speed Link Speed of the stack port (12 or 42) in Gb/s. Admin Status The only currently listed status is Up.
PAGE 1526
Example (Topology) Related Commands DellEMC#show system stack-ports topology Topology: Ring Interface Connection --------------------1/53 6/53 1/54 2/53 2/53 1/54 2/54 3/53 3/53 2/54 3/54 4/53 4/53 3/54 4/54 5/53 5/53 4/54 5/54 6/54 6/53 1/53 6/54 5/54 DellEMC# • • • reset stack-unit – resets the designated stack member. show hardware stack-unit – displays the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 1527
stack-unit provision Preconfigure a logical stacking ID of a switch that joins the stack. This is an optional command that is executed on the management unit. Syntax Parameters stack-unit [stack-number] provision {model-identifier} stack-number Enter a stack member identifier of the switch that you want to add to the stack. model-identifier Enter the model identifier of the switch to be added as a stack member. This identifier is also referred to as the provision type.
PAGE 1528
Version Description 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810. 8.3.12.0 Reset command mode from EXEC to CONFIGURATION. Usage Information The following message displays to confirm the command. Setting ports Fo 1/60 as stack group will make their interface configs obsolete after a reload.
PAGE 1529
• • • reset stack-unit — resets the designated stack member. show system — displays the status of all stack members or a specific member. show version — displays the current Dell EMC Networking OS version information on the system.
PAGE 1530
57 Storm Control The Dell EMC Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell EMC Networking OS. Important Points to Remember • • • • • • • • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1531
• • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defaults none Command Modes • • Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. EXEC EXEC Privilege Version Description 9.10(0.
PAGE 1532
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1533
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1534
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-MUX (PMUX) mode only. 8.3.19.
PAGE 1535
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
PAGE 1536
Version Description 7.6.1.0 Introduced on the C-series and S-Series. Usage Information Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter. It is possible, however, that some multicast control traffic may get dropped when storm control thresholds are exceeded. storm-control multicast (Interface) Configure the percentage of multicast traffic allowed on an C-Series or S-Series interface (ingress only) network only.
PAGE 1537
Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.9(0.0) Introduced on the C9010, S4810, S4820T, S5000, S6000, Z9500, S3048-ON, S4048-ON, and S6000–ON.
PAGE 1538
Usage Information Unknown Unicast Storm-Control is valid for Layer 2 and Layer 2/Layer 3 interfaces. storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only).
PAGE 1539
58 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell EMC Networking switch/routing platform. Topics: • • • • • • • • • • • • bridge-priority bpdu-destination-mac-address debug spanning-tree description disable forward-delay hello-time max-age protocol spanning-tree show config show spanning-tree 0 spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree.
PAGE 1540
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs.
PAGE 1541
To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0. protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information.
PAGE 1542
Defaults none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1543
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • protocol spanning-tree — enter SPANNING TREE mode on the switch. forward-delay The amount of time the interface waits in the Listening state and the Learning state before transitioning to the Forwarding state.
PAGE 1544
hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10. The default is 2 seconds. Defaults 2 seconds Command Modes SPANNING TREE Command History This guide is platform-specific.
PAGE 1545
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1546
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information STP is not enabled when you enter SPANNING TREE mode.
PAGE 1547
Example DellEMC(config-stp)# show config protocol spanning-tree 0 no disable DellEMC(config-stp)# show spanning-tree 0 Display the spanning tree group configuration and status of interfaces in the spanning tree group. Syntax Parameters show spanning-tree 0 [active | brief | guard | interface interface | root | summary] 0 Enter 0 (zero) to display information about that specific spanning tree group. active (OPTIONAL) Enter the keyword active to display only active interfaces in spanning tree group 0.
PAGE 1548
Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.4.2.1 Added support for the optional guard keyword on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information Enable spanning tree group 0 prior to using this command. The following describes the show spanning-tree 0 command shown in the example.
PAGE 1549
Designated root has priority 32768, address 0001.e800.0a56 Designated bridge has priority 32768, address 0001.e800.0a56 Designated port id is 8.26, designated path cost 0 Timers: message age 0, forward_delay 0, hold 0 Number of transitions to forwarding state 1 BPDU: sent:18, received 0 The port is not in the portfast mode Port 27 (TenGigabitEthernet 1/2) is Forwarding Port path cost 4, Port priority 8, Port Identifier 8.27 Designated root has priority 32768, address 0001.e800.
PAGE 1550
spanning-tree Assigns a Layer 2 interface to STP instance 0 and configures a port cost or port priority, or enables loop guard, root guard, or the Portfast feature on the interface. Syntax spanning-tree stp-id {cost cost | {loopguard | rootguard} | portfast [bpduguard [shutdown-on-violation]] | priority priority} To disable Spanning Tree group on an interface, use the no spanning-tree stp-id {cost cost | {loopguard | rootguard} | portfast [bpduguard [shutdown-on-violation]] | priority priority} command.
PAGE 1551
Version Description 8.3.10.1 Introduced the loopguard and rootguard options on the S4810. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series, C-Series, and SSeries. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the shutdown-on-violation option. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1552
59 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide.
PAGE 1553
Usage Information • • • Example When you run the command, the system displays a message with the information directing to the URL for further information. Even before you accept or reject the EULA, the configuration data is sent to the default centrally deployed SupportAssist Server. If you reject the EULA, the configuration data is not transmitted to the SupportAssist server. If there is an existing SupportAssist configuration, the configuration is not removed and the feature is disabled.
PAGE 1554
Related Commands • support-assist — moves to the SupportAssist Configuration mode. support-assist Move to the SupportAssist configuration mode. Syntax support-assist To remove all the configuration of the SupportAssist service, use the no support-assist command. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1555
support-assist activity Trigger an activity event immediately. Syntax Parameters support-assist activity {full-transfer | core-transfer} start now full-transfer Enter the keyword full-transfer to specify transfer of configuration, inventory, logs, and other information. core-transfer Enter the keyword core-transfer to specify transfer of core files. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1556
Version Description Introduced the core-transfer and event-transfer parameters. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Usage Information By default, each activity follows a set of default actions using a default schedule.
PAGE 1557
last-name Enter the last name for the contact person. To include a space, enter a space within double quotes. Command Modes SUPPORTASSIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1558
Parameters default Enter the keyword default for the default server. server-name Enter the name of the custom server to which the logs would be transferred. To include a space, enter a space within double quotes. Defaults Default server has URL stor.g3.ph.dell.com Command Modes SUPPORTASSIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1559
Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Usage Information The remote file specification for full transfer includes the protocol that is used to copy the file from the remote system. The default Manifest-file for full transfer includes records like alarms, logs, operational, and configuration data. Related Commands • • • action-manifest install — configure the action-manifest to use for a specific activity.
PAGE 1560
Parameters Command Modes local-file-name Enter the name of the local action-manifest file. Allowable characters are: a to z, A to Z, 0 to 9, -, _, and space. SUPPORTASSIST ACTIVITY FULL-TRANSFER SUPPORTASSIST ACTIVITY EVENT-TRANSFER Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.
PAGE 1561
enable Enable a specific SupportAssist activity. Syntax enable To disable a particular SupportAssist activity, use the no enable command. Defaults Enabled Command Modes SUPPORTASSIST ACTIVITY FULL-TRANSFER SUPPORTASSIST ACTIVITY CORE-TRANSFER SUPPORTASSIST ACTIVITY EVENT-TRANSFER Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.
PAGE 1562
postalcode | (OPTIONAL) Enter the keyword postalcode or zipcode then the postal code or zip zipcode company- code for the company site, as one string with no spaces. code Command Modes SUPPORTASSIST COMPANY Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON.
PAGE 1563
territory Configure the territory and set the coverage for the company site. Syntax territory company-territory To remove the company territory information, use the no territory command. Parameters company-territory Enter the territory name for the company. To include a space, enter a space within double quotes. Use three-letter country codes like USA, IND, FRA, GER and so on. Command Modes SUPPORTASSIST COMPANY Command History This guide is platform-specific.
PAGE 1564
Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Usage Information The email addresses must have the standard form of @ to be considered valid. This command is optional for SupportAssist service configuration. Related Commands • preferred-method — configure the preferred method for contacting the person. phone Configure phone numbers to reach the contact person.
PAGE 1565
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.
PAGE 1566
To remove the proxy, use the no proxy-ip-address command. Parameters ipv4-address Enter the IP address of the proxy server in a dotted decimal format (A.B.C.D). ipv6-address Enter the IPv6 address of the proxy server in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. NOTE: To use the IPv6 address, the Open Automation package should also support IPv6 communications. For this purpose, SupportAssist requires Dell EMC Networking Open Automation 9.10(0.
PAGE 1567
Related Commands Version Description 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. • server — configure the name of the remote SupportAssist server. url Configure the URL to reach the SupportAssist remote server. Syntax url uniform-resource-locator To delete the URL for the server, use the no url command.
PAGE 1568
Example Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. DellEMC# show eula-consent support-assist SupportAssist EULA has been: Accepted Additional information about the SupportAssist EULA is as follows: By installing SupportAssist, you allow Dell to save your contact information (e.g.
PAGE 1569
show running-config Display the current configuration and changes from the default values. Syntax Parameters show running-config support-assist support-assist Enter the keyword support-assist to view the detailed configuration for the feature. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.11(0.
PAGE 1570
Example Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. DellEMC#show support-assist status SupportAssist Service: Installed EULA: Accepted Server: default Enabled: Yes URL: https://stor.g3.ph.dell.
PAGE 1571
60 System Time and Date The commands in this section configure time values on the system, either using the Dell EMC Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell EMC Networking OS Configuration Guide.
PAGE 1572
end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year. The range is from 1993 to 2035. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to1440. The default is 60 minutes. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1573
• • first: Enter this keyword to start daylight saving time in the first week of the month. last: Enter this keyword to start daylight saving time in the last week of the month. start-day Enter the name of the day that you want daylight saving time to begin. Use English three letter abbreviations; for example, Sun, Sat, Mon, and so on. The range is from Sun to Sat. start-month Enter the name of one of the 12 months in English. start-time Enter the time in hours:minutes.
PAGE 1574
Related Commands Version Description 6.1.1.0 Introduced on the E-Series. • • • ntp trusted-key — configures a trusted key. clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. show clock — displays the current clock settings. clock timezone Configure a timezone for the switch. Syntax clock timezone timezone-name offset To delete a timezone configuration, use the no clock timezone command.
PAGE 1575
debug ntp Display Network Time Protocol (NTP) transactions and protocol messages for troubleshooting. Syntax debug ntp {level level-number} To disable debugging of NTP transactions, use the no debug ntp {level level-number} command. Parameters level Enter the keyword level then the level–number to display information about NTP logs. The log level range is from 1 to 6. • • 1 is the most important log level. 6 is the least important log level.
PAGE 1576
Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp authentication-key Specify a key for authenticating the NTP server. Syntax ntp authentication-key key-number {md5 | sha1} {0 | 7} key Parameters key-number Specify a number for the authentication key. The range is from 1 to 65534.
PAGE 1577
Version Description 6.1.1.0 Introduced on the E-Series. Usage Information After configuring the ntp authentication-key command, configure the ntp trusted-key command to complete NTP authentication. Dell EMC Networking OS versions 8.2.1.0 and later use an encryption algorithm to store the authentication key that is different from previous Dell EMC Networking OS versions; beginning in version 8.2.1.
PAGE 1578
ntp control-key-passwd Configure control key password for NTPQ authentication. NTP control key supports encrypted and unencrypted option. Syntax ntp control-key-passwd [encryption-type] password To delete the control key, use the no ntp control-key-passwd [encryption-type] password command. Parameters encryption-type (OPTIONAL) Enter one of the following numbers: • • • password 0 (zero) directs the system to store the password as clear text.
PAGE 1579
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp master Configure the switch as NTP Server. Syntax Parameters ntp master ntp master Enter the stratum number to identify the NTP Server's hierarchy.
PAGE 1580
hostname Enter the host name of the server. key keyid (OPTIONAL) Enter the keyword key and a number as the NTP peer key. The range is from 1 to 65534. prefer (OPTIONAL) Enter the keyword prefer to indicate that this peer has priority over other servers. version number (OPTIONAL) Enter the keyword version and a number to correspond to the NTP version used on the server. The range is from 1 to 4. minpoll pollinginterval (OPTIONAL) Enter the keyword minpollthen the polling-interval.
PAGE 1581
When the Dell EMC Networking OS NTP client receives inconsistent timestamp in the origin timestamp filed, it logs the syslog message. It is due to the older versions of NTPD server implementation. Upgrade the system to the latest NTPD package in the NTP server and the system logs the following NTP syslog message: Dell EMC# May 30 13:27:46 %STKUNIT2-:CP %ntp-6-: receive: Unexpected origin timestamp 0xdeb95bee.06ba346e does not match aorg 0000000000.00000000 from server@10.16.151.117 xmt 0xdeb95bee.
PAGE 1582
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp step-threshold Configure the step-threshold time interval.
PAGE 1583
Version Description 9.14(1.0) Introduced the trusted-key range update on the S4810 and S4820T. 9.14(0.0) The trusted-key range value is increased from 1 to 65534. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1584
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example DellEMC#show clock 11:05:56.949 UTC Thu Oct 25 2001 DellEMC# Example (Detail) Related Commands DellEMC# show clock detail 12:18:10.
PAGE 1585
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The following describes the show ntp associations command shown in the Example below. Field Description (none) One or more of the following symbols could be displayed: • • • • • Example (without ntp master configuration) Example (with ntp master configuration) * means synchronized to this peer.
PAGE 1586
Related Commands • • LOCAL(0) indicates that the local machine synchronizes with itself. .LOCL. indicates reference clock of the NTP master. • show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXECEXEC Privilege Command History This guide is platform-specific.
PAGE 1587
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1588
61 Tunneling Tunneling is supported on Dell EMC Networking OS. Topics: • • • • • • • • • • ip unnumbered ipv6 unnumbered tunnel allow-remote tunnel destination tunnel dscp tunnel flow-label tunnel hop-limit tunnel keepalive tunnel-mode tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1589
• • If the logical ip address is configured. If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ip unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address. The tunnel interface is not changed to operationally up until the logical IP address is identified from one of the address family.
PAGE 1590
tunnel allow-remote Configure an IPv4 or IPv6 address or prefix whose tunneled packets are accepted for decapsulation. If you do not configure allow-remote entries, tunneled packets from any remote peer address is accepted. This feature is supported on Dell EMC Networking OS. Syntax tunnel allow-remote {ip-address | ipv6-address} [mask] To delete a configured allow-remote entry use the no tunnel allow-remote command. Any specified address/mask values must match an existing entry for the delete to succeed.
PAGE 1591
ipv6–address Enter the destination IPv6 address for the tunnel. Defaults none Command Modes INTERFACE TUNNEL (conf-if-tu) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 1592
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. Usage Information This command configures the method used to set the high 6 bits (the differentiated services codepoint) of the IPv4 TOS or the IPv6 traffic class in the outer IP header.
PAGE 1593
To restore the default tunnel hop-limit, use the no tunnel hop-limit command. Parameters value Enter the hop limit (ipv6) or time-to-live (ipv4) value to include in the tunnel header. The range is from 0 to 255. The default is 64. Defaults 64 (Time-to-live for IPv4 outer tunnel header or hop limit for IPv6 outer tunnel header) Command Modes INTERFACE TUNNEL (conf-if-tu) Command History This guide is platform-specific.
PAGE 1594
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000 and Z9000.
PAGE 1595
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the decapsulate-any command. 9.3(0.1) Introduced on the S6000 and Z9000. Usage Information To enable a tunnel interface, use this command. You must define a tunnel mode for the tunnel to function. If you previously defined the tunnel destination or source address, the tunnel mode must be compatible.
PAGE 1596
Version Description 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the tunnel source anylocal command. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. Usage Information Added an optional keyword “anylocal” to the tunnel source command. The anylocal argument can be used in place of the ip address or interface, but only with the multipoint receive-only mode tunnels.
PAGE 1597
62 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1598
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • • downstream — assigns a port or port-channel to the uplink-state group as a downstream interface.
PAGE 1599
description Enter a text description of an uplink-state group. Syntax Parameters description text text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. Defaults none Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.
PAGE 1600
Defaults none Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series. 9.10(0.0) Introduced on the S3148. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1601
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • • downstream — assign a port or port-channel to the uplink-state group as a downstream interface. uplink-state-group — create an uplink-state group and enables the tracking of upstream links.
PAGE 1602
To disable upstream-link tracking without deleting the uplink-state group, use the no enable command. Defaults Upstream-link tracking is automatically enabled in an uplink-state group. Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Related Commands Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(2.0) Introduced on the S3100 series.
PAGE 1603
Version Description 8.4.2.3 Introduced on the S-Series S50. Example Related Commands DellEMC# show running-config uplink-state-group ! no enable uplink state track 1 downstream twentyFiveGigE 1/2,4,6,11-19 upstream FortyGigE 1/49, 29 upstream PortChannel 1 ! uplink state track 2 downstream twentyFiveGigE 1/1,3,5,7-10 upstream FortyGigE 1/49,42 • • show uplink-state-group — displays the status information on a specified uplink-state group or all groups.
PAGE 1604
Uplink State Group: 7 Status: Enabled, Up Uplink State Group: 16 Status: Disabled, Up DellEMC# show uplink-state-group 16 Uplink State Group: 16 Status: Disabled, Up DellEMC#show uplink-state-group detail (Up): Interface up (Dwn): Interface down (Dis): Interface disabled Uplink State Group : 1 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/25(Up) Te 1/28(Up) Downstream Interfaces : Te 5/1(Up) Te 5/1(Up) Te 5/3(Up) Te 5/
PAGE 1605
Upstream Interfaces : Te 1/25(Dwn) Po 8(Dwn) Downstream Interfaces : Te 1/30(Dwn) Related Commands • • show running-config uplink-state-group — displays the current configuration of one or more uplink-state groups. uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. uplink-state-group Create an uplink-state group and enable the tracking of upstream links on a switch or router.
PAGE 1606
upstream Assign a port or port-channel to the uplink-state group as an upstream interface. Syntax upstream interface To delete an uplink-state group, use the no upstream interface command.
PAGE 1607
63 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell EMC Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1608
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information When packets are colored green; no packets are dropped.
PAGE 1609
Version Description 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information Enable DEI before using this command. dei mark Set the DEI value on egress according to the color currently assigned to the packet. S4048–ON Syntax Parameters dei mark {green | yellow} {0 | 1} 0|1 Enter the bit value you want to map to a color. green | red | yellow Choose a color: • • Green: High priority packets that are the least preferred to be dropped.
PAGE 1610
Parameters interface Enter the following keywords and the interface information: • • • For a Port Channel interface, enter the keywords port-channel, and then a number. For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. Defaults Not configured. Command Modes CONF-IF-VLAN Command History This guide is platform-specific.
PAGE 1611
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.10.2 Introduced on the S4810.
PAGE 1612
Version Description 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to enabling this command, to place the interface in Layer 2 mode, enter the switchport command. To remove the access port designation, remove the port (using the no member interface command) from all stackable VLAN-enabled VLANs. vlan-stack compatible Enable the stackable VLAN feature on a VLAN.
PAGE 1613
Example DellEMC# show vlan Codes: * - Default VLAN, G - GVRP VLANs * NUM 1 2 Status Inactive Active 3 Active 4 Active 5 Active DellEMC# Q Ports M M M M M M M M M M M Te 1/13 Te 1/1-3 Po1(Te 1/14-15) Te 1/18 Te 1/4 Po1(Te 1/14-15) Te 1/18 Te 1/5 Po1(Te 1/14-15) Te 1/18 Te 1/6 vlan-stack dot1p-mapping Map C-Tag dot1p values to an S-Tag dot1p value.
PAGE 1614
vlan-stack protocol-type Define the stackable VLAN tag protocol identifier (TPID) for the outer VLAN tag (also called the VMAN tag). If you do not configure this command, the Dell EMC Networking OS assigns the value 0x9100. Syntax vlan-stack protocol-type number Parameters number Enter the hexadecimal number as the stackable VLAN tag. You may specify both bytes of the 2-byte S-Tag TPID. The range is from 0 to FFFF. The default is 9100.
PAGE 1615
vlan-stack trunk Specify a Layer 2 port or port channel as a trunk port to the stackable VLAN network. Syntax vlan-stack trunk To remove a trunk port designation from the selected interface, use the no vlan-stack trunk command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1616
no ip address switchport vlan-stack trunk no shutdown DellEMC(conf-if-te-1/42)# interface vlan 100 DellEMC(conf-if-vl-100)# vlan-stack compatible DellEMC(conf-if-vl-100-stack)# member tengigabitethernet 1/42 DellEMC(conf-if-vl-100-stack)# show config ! interface Vlan 100 no ip address vlan-stack compatible member TenGigabitEthernet 1/42 shutdown DellEMC(conf-if-vl-100-stack)# interface vlan 20 DellEMC(conf-if-vl-20)# tagged Tengigabitethernet 1/42 DellEMC(conf-if-vl-20)# show config ! interface Vlan 20 no i
PAGE 1617
64 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time. Topics: • • • • • • • • • • • • • • ip vrf ip http vrf description ip vrf forwarding ip route-export ip route-import ipv6 route-export ipv6 route-import match source-protocol redistribute interface management maximum dynamic-routes show ip vrf show run vrf ip vrf Create or delete a customer VRF.
PAGE 1618
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 1619
Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
PAGE 1620
DellEMC(conf-vrf)# description "Red Network" DellEMC(conf-vrf)# show config ! ip vrf red 4 description "Red Network" DellEMC(conf-vrf)# DellEMC(conf-if-te-1/45)# int te 7/46 DellEMC(conf-if-te-1/46)# no shut DellEMC(conf-if-te-1/46)# ip vrf forwarding red DellEMC(conf-if-te-1/46)# ip add 100.1.1.1/24 DellEMC(conf-if-te-1/46)# DellEMC(conf-if-te-1/46)# DellEMC(conf-if-te-1/46)# DellEMC(conf-if-te-1/46)# show config ! interface TenGigabitEthernet 1/46 ip vrf forwarding red ip address 100.1.1.
PAGE 1621
In Dell EMC Networking OS, you can configure one route-export per VRF as you can only expose one set of routes for leaking. However, you can configure multiple route-import targets because a VRF can accept routes from multiple VRFs. You can expose a unique set of routes from the source VRF for leaking to other VRFs. When two VRFs leak or export routes, there is no option to discretely filter leaked routes from each source VRF.
PAGE 1622
ipv6 route-export Enables route leaking between VRFs. This command exports or shares IPv6 routes corresponding to one VRF with other nondefault VRFs. Syntax ipv6 route-export tag [route-map-name] Parameters route-export Enter the keywords route-export to leak or share routes between VRFs. tag Enter a tag (ASN number) as the export route target to expose routes to other VRFs. This tag acts as an identifier for exported routes.
PAGE 1623
Parameters route-import Enter the keywords route-import to import IPv6 routes into the VRF. tag Enter a tag (ASN number) to specify an import route target for importing routes from another VRF. To import leaked routes from another VRF, use the same ASN number that is specified as the export route target at the source VRF. route-map-name Enter the name of the route-map to filter the imported routes. NOTE: Use the route-map attribute while importing routes from the global RTM.
PAGE 1624
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. Usage Information Specify the matching criteria only after defining a route-map.
PAGE 1625
interface management Associates a management port with a management VRF. Syntax interface management To delete the association between a management port and a management VRF, use the no interface management command. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1626
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4(0.0) Introduced on the S–Series.
PAGE 1627
Ma 6/1, Nu 0, Vl 1 Te 1/14,16-17 Te 1/15 test1 test2 management 1 2 64 DellEMC# show ip vrf test1 VRF-Name VRF-ID Interfaces test1 1 Te 1/14,16-17 show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax Parameters show run vrf vrf-name vrf vrf-name Enter the keyword vrf and then the name of the VRF. Command Modes • • Command History This guide is platform-specific.
PAGE 1628
65 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
PAGE 1629
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.
PAGE 1630
Version Description 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1631
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. Usage Information You must configure the VLT port channel interface which is connecting to the remote VLT domain as peerdomain-link. You can also configure the VLANs you want to exclude from the VLT proxy gateway.
PAGE 1632
vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. S4048–ON Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1633
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 1634
66 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1635
back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax Parameters back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds] vrf [management vrf-name | vrf-name]} ipv4–address Enter the IPv4 address of the backup destination. ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format.
PAGE 1636
clear vlt statistics Clear the VLT operation statistics. Syntax clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP. Command Modes EXEC Command History This guide is platform-specific.
PAGE 1637
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax Parameters delay-restore delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Defaults Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1638
Defaults 60 seconds Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1639
Version Description 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810. Usage Information LACP on the VLT ports (on a VLT switch or access device), which are members of the VLT, are not brought up until the VLT domain is recognized on the access device. During boot-up in a stacking configuration, the system must be able to reach the DHCP server with the boot image and configuration image.
PAGE 1640
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000.
PAGE 1641
Version Description 8.3.8.0 Introduced on the S4810. Usage Information To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option. When a VLT peer with bare metal provisioning (BMP) is booting up, it sends untagged DHCP discover packets to its peer over the VLTi. To ensure that the DHCP discover packets are forwarded to the VLAN that has the DHCP server, use this configuration.
PAGE 1642
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for default value on the S-Series and Z-Series. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added the support for IPV6 / IPV4.
PAGE 1643
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information After you configure a VLT domain on each peer switch and connect (cable) the two VLT peers on each side of the VLT interconnect, the system elects a primary and secondary VLT peer device. To configure the primary and secondary roles before the election process, use the primary-priority command. Enter a lower value on the primary peer and a higher value on the secondary peer.
PAGE 1644
Delay-Restore timer : Delay-Restore Abort Threshold : Peer-Routing : Peer-Routing-Timeout timer : Multicast peer-routing timeout: DellEMC# 90 seconds 60 seconds Disabled 0 seconds 150 seconds show vlt backup-link Displays information about the backup link operation. Syntax show vlt backup-link Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1645
igmp-snoop Enter the keywords igmp-snoop to display the igmp-snooping counter information for the VLT. interface Enter the keyword interface to display the interface counter information for the VLT. mac Enter the keyword mac to display the MAC address counter information for the VLT. ndp Enter the keyword ndp to display the VLT counter information for NDP. Default Not configured. Command Modes EXEC Command History This guide is platform-specific.
PAGE 1646
IGMP Mcast Groups count Ve Example (NDP and Non-VLT ARP) : 0 DellEMC#show vlt counters Total VLT Counters ------------------L2 Total MAC-Address Count: Total Arp Entries Learnt : Total Arp Entries Synced : Total Non-VLT Arp entries Learnt: Total Non-VLT Arp Entries Synced IGMP MRouter Vlans count : IGMP Mcast Groups count : Total VLT Ndp Entries Learnt : Total VLT Ndp Entries Synced : Total Non-VLT Ndp Entries Learnt : Total Non-VLT Ndp Entries Synced : 2 0 0 0 0 2 0 0 0 show vlt detail Displays detaile
PAGE 1647
show vlt inconsistency Display run-time inconsistencies in the incoming interface (IIF) for spanned multicast routes (mroutes). Syntax show vlt inconsistency ip mroute Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 1648
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced support for Q-in-Q implementation over VLT on the S-Series and Z-Series. Introduced on t ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mod 9.0.2.0 Introduced on the S6000.
PAGE 1649
--------------66.66.66.
PAGE 1650
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1651
Related Commands Example Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Added parameters multicast and ndp 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support in the output for ARP, MAC, and IGMP snooping.
PAGE 1652
Route Route Route Route updates sent to Peer: 0 updates rcvd from Peer: 0 update pkts sent to Peer: 0 update pkts rcvd from Peer: 0 VLT NDP Statistics -------------------NDP NA VLT Tunnel Pkts sent:16 NDP NA VLT Tunnel Pkts Rcvd:46 NDP NA Non-VLT Tunnel Pkts sent:0 NDP NA Non-VLT Tunnel Pkts Rcvd:0 Ndp-sync Pkts Sent:144 Ndp-sync Pkts Rcvd:105 Ndp Reg Request sent:25 Ndp Reg Request rcvd:24 show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between
PAGE 1653
system-mac Reconfigure the default MAC address for the domain. Syntax Parameters system-mac mac-address mac-address Enter the system MAC address for the VLT domain. Defaults Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
PAGE 1654
Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information When you create a VLT domain on a switch, the Dell EMC Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for internal system operations.
PAGE 1655
vlt-peer-lag port-channel Associate the port channel to the corresponding VLT peer port channel for the VLT connection to an attached device. Syntax Parameters vlt-peer-lag port-channel id-number id-number Enter the respective VLT port-channel number of the peer device. The range is from 1 to 128. Defaults Not configured. Command Modes INTERFACE PORT-CHANNEL Command History This guide is platform-specific.
PAGE 1656
Usage Information If you add an ICL or VLTi link as a member of a primary VLAN, the ICL becomes a part of the primary VLAN and its associated secondary VLANs, similar to the behavior for normal trunk ports. VLAN symmetry is not validated if you associate an ICL to a PVLAN. Similarly, if you dissociate an ICL from a PVLAN, although the PVLAN symmetry exists, ICL is removed from that PVLAN. The ICL Status field displays the type of VLAN port of the VLTi link configured in a PVLAN.
PAGE 1657
67 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell EMC Networking OS.
PAGE 1658
clear mac-address-table dynamic Clear the MAC address table of specific or all MAC address learned dynamically. Syntax clear mac-address-table dynamic {vxlan {interface interface-type | remote-vtepip ip-address | vnid vnid} | all | interface | vlan | vxlan} Parameters interface interface-type Enter the keyword interface and the interface type to clear all MAC addresses learnt on that interface. The same is also notified to the controller.
PAGE 1659
Related Commands Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.10(0.1P10) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. vxlan-instance — Enable VXLAN instance configuration on the platform. debug vxlan Debug messages between the Gateway and Controller.
PAGE 1660
NOTE: • This command is only applicable for static VXLAN and does not work for the other modes of VXLAN (controller and nuage). • The remote VTEP should already be configured. • In case of static VXLAN VLT deployments, this configuration should be symmetric across VLT nodes. feature vxlan Enable VXLAN configuration globally on the platform. Syntax feature vxlan To disable the VXLAN, use the no feature vxlan command.
PAGE 1661
Related Commands Version Description 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. vxlan-instance— Enable VXLAN Instance configuration on the platform. gateway-ip Configures gateway IP address on the platform. Syntax Parameters gateway-ip IP address IP address Enter the IP address of the gateway for the VXLAN instance. Defaults Disabled Command Modes VXLAN INSTANCE Command History This guide is platform-specific.
PAGE 1662
Usage Information Use the local-vtep-ip IP Address command to set the local IP Address that would be used as source for VXLAN tunnels. max_backoff Configures time to wait between connection attempts with controller. Syntax max_backoff time Parameters time Enter the time in milliseconds. The range is from 1000-180000. The default value is 30000. Defaults 30000 Command Modes VXLAN INSTANCE Command History This guide is platform-specific.
PAGE 1663
remote-vtep-ip Create a remote VTEP and associate it to specified VNIDs. Syntax remote—vtep—ip IP Address vni-profile profile name To delete the remote VTEP, use the no remote—vtep—ip command. Parameters IP Address Enter the IP Address of the remote VTEP. vni-profile Enter the keyword vni-profile followed by the profile name to which the remote VTEP has to be associated. Defaults None. Command Modes VXLAN-INSTANCE Command History This guide is platform-specific.
PAGE 1664
Parameters profile name Enter a valid and unique profile name. The profile name can have a maximum of 32 characters. Defaults None Command Modes VXLAN-INSTANCE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON.
PAGE 1665
Example Enable VXLAN instance: DellEMC(conf)#int 1/5/1 DellEMC(conf-if-te-1/5/1)#vxlan-instance 1 DellEMC(conf-if-te-1/5/1-vxlan-inst-1)#no shutdown Disable VXLAN instance: DellEMC(conf)#no vxlan-instance 1 Related Commands feature vxlan — Enable VXLAN configuration globally on the platform. vxlan-instance (VAP) To configure a VXLAN-Access Port (VAP) in to VXLAN-instance Syntax vxlan-instance instance ID To unconfigure VAP, use the no vxlan-instance 1 command.
PAGE 1666
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.14(0.0) Updated to enable MAC level loopback. 9.13(0.0) Introduced on the S4048T-ON, S4048–ON, S6010–ON, S6000–ON, S6100–ON, S6000, and Z9100–ON. Usage Information You must configure VXLAN globally before using VXLAN-instance. Use the no shutdown command to enable the VXLAN instance.
PAGE 1667
You cannot modify a VXLAN instance mode. If you need to change the mode, you can delete the existing VXLAN instance and create a new instance with the required mode. Example Enable VXLAN instance: DellEMC(conf)#feature vxlan DellEMC(conf)#vxlan-instance 1 static DellEMC(conf-vxlan-inst-1)#no shutdown Disable VXLAN instance: DellEMC(conf)#no vxlan-instance 1 static vxlan-vnid Associate VNID to VLAN. Syntax vxlan-vnid VNID To remove the association, use the no vxlan-vnid command.
PAGE 1668
Example Static Mode: DellEMC#show running-config vxlan ! feature vxlan ! vxlan-instance 1 static local-vtep-ip 1.1.1.1 no shutdown vni-profile ni1 vnid 1 remote-vtep-ip 2.2.2.2 vni-profile ni1 Controller Mode: DellEMC#show running-config vxlan ! feature vxlan ! vxlan-instance 1 gateway-ip 3.3.3.3 fail-mode secure controller 1 192.168.122.6 port 6632 ssl no shutdown Related Commands vxlan-instance- Enable VXLAN Instance configuration on the platform.
PAGE 1669
MAX Backoff Controller 1 Fail Mode Port List Fo 1/49 Te Related Commands : 30000 : 192.168.122.6:6632 ssl (connected) : secure : 1/16 Te 1/20 Po 2 vxlan-instance- Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance logical network Displays logical network information related to Network Virtualization Overlay (NVO) Gateway. Syntax Parameters show vxlan vxlan-instance instance ID logical-network [name name] instance ID Enter the VXLAN instance ID.
PAGE 1670
show vxlan vxlan-instance physical-locator Displays physical locators related to Network Virtualization Overlay (NVO) Gateway. Syntax show vxlan vxlan-instance instance ID physical—locator [vtep-ip A.B.C.D] Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. A.B.C.D Enter the IP address of the VTEP. Defaults Disabled Command Modes VXLAN INSTANCE Command History This guide is platform-specific.
PAGE 1671
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON.
PAGE 1672
show vxlan vxlan-instance unicast-mac-local Displays the information of the local unicast MAC associated with the logical network related to Network Virtualization Overlay (NVO) Gateway. Syntax show vxlan vxlan-instance instance ID unicast-mac-local [logical—network name | vnid VNID] Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. name (Optional) Enter the name of VXLAN logical network with a maximum length of 30 characters.
PAGE 1673
vnidVNID (Optional) Enter the keyword vnid and then enter the ID of the VXLAN. The range is from 1 to 16777215. Command Modes • • Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.13(0.0) Updated to show VLT peer’s local macs. 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. 9.10(0.
PAGE 1674
Remote Vtep IP VNI profile VNID count VNID list 1674 Virtual Extensible LAN (VXLAN) : : : : 10.10.10.
PAGE 1675
68 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell EMC Networking OS. Topics: • • IPv4 VRRP Commands IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1676
Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information Dell EMC Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges. Syntax authentication-type simple [encryption-type] password To delete an authentication type and password, use the no authentication-type command.
PAGE 1677
clear counters vrrp Clear the counters maintained on VRRP operations. Syntax Parameters clear counters vrrp [vrrp-id] [ipv6] vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1678
debug vrrp Enable VRRP debugging. Syntax debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} To disable debugging, use the no debug vrrp [vrrp-id] {all | bfd | database | interface | ipv6 | packets | state | timer} command. Parameters vrrp-id (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups. bfd Enter the keyword bfd to enable debugging of VRRP BFD interactions.
PAGE 1679
Version Description 6.2.1.1 Introduced on the E-Series. Usage Information If you do not specify an option, debug is active on all interfaces and all VRRP groups. description Configure a short text string describing the VRRP group. Syntax description text To delete a VRRP group description, use the no description command. Parameters text Enter a text string up to 80 characters long. Defaults Not enabled. Command Modes VRRP Command History This guide is platform-specific.
PAGE 1680
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1681
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1682
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command. Parameters priority Enter a number as the priority.
PAGE 1683
show config View the non-default VRRP configuration. Syntax show config [verbose] Parameters verbose (OPTIONAL) Enter the keyword verbose to view all the VRRP group configuration information, including default information. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1684
• • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a VLAN interface, enter the keyword vlan, and then the VLAN ID. The VLAN ID range is from 1 to 4094. ipv6 (OPTIONAL) Enter the keyword ipv6 to view only VRRP IPv6 groups.
PAGE 1685
Item Description • • • Example (Brief) NA/IF (the interface is not available). MASTER (the interface associated with the MASTER router). BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router. Virtual addr(s) Displays the virtual IP addresses of the VRRP routers associated with the interface.
PAGE 1686
State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.252 Authentication: (none) Tracking states for 1 interfaces: Up TenGigabitEthernet 1/17 priority-cost 10 -----------------TenGigabitEthernet 1/4, VRID: 2, Net: 10.1.2.253 VRF: 0 default State: Master, Priority: 110, Master: 10.1.2.
PAGE 1687
To disable monitoring, use the no track interface command. Parameters interface (OPTIONAL) Enter the following keywords and the interface information: • • • priority-cost For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a VLAN interface, enter the keyword vlan, and then the VLAN ID. The VLAN ID range is from 1 to 4094.
PAGE 1688
Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.8(2.0) Introduced on the S3100 series. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1689
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information This command applies to a single interface. When you use this command with the vrrp delay reload command, the later timer rules VRRP enabling.
PAGE 1690
• When an interface comes up, whether as part of a system reload or an interface reload, the system waits 300 seconds (5 minutes) to bring up VRRP on that interface. For the delay timers to take effect, save the configuration and reload the system. Related Command • vrrp delay minimum — sets the delay time for VRRP initialization after a line card reboot. vrrp-group Assign a VRRP ID to an interface. You can configure up to 12 VRRP groups per interface.
PAGE 1691
3 Enter the keyword 3 to specify VRRP version 3 as defined by RFC 5798, Virtual Router Redundancy Protocol. both Enter the keyword both for in-service migration from VRRP version 2 to VRRP version 3. Defaults 2 Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.
PAGE 1692
• • • priority show config virtual-address clear counters vrrp ipv6 Clear the counters recorded for IPv6 VRRP groups. Syntax clear counters vrrp ipv6 [vrid | vrf vrf-name] Parameters vrid (OPTIONAL) Enter the number of an IPv6 VRRP group; range is from 1 to 255. vrf vrf-name (OPTIONAL) Enter the name of a VRF instance to clear the counters of all IPv6 VRRP groups in the specified VRF. The maximum is 32 characters. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1693
debug vrrp ipv6 Enable VRRP debugging. Syntax Parameters debug vrrp ipv6 interface [vrid] {all | packets | state | timer} interface Enter the following keywords and the interface information: • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport[/subport] information. For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. For a Port Channel interface, enter the keywords port-channel, and then a number.
PAGE 1694
show vrrp ipv6 View the active IPv6 VRRP groups. If no VRRP groups are active, the Dell EMC Networking OS returns No Active VRRP group. Syntax show vrrp ipv6 [vrid] [interface] [brief] [vrf vrf-name] Parameters vrid (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255.
PAGE 1695
Line starting with Description • • master (MASTER virtual router) backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:... Displays additional VRRP configuration information: • • • Adv rcvd:... Displays counters for the following: • • • Adv rcvd displays the number of VRRP advertisements received on the interface. Adv sent displays the number of VRRP advertisements sent on the interface.
PAGE 1696
Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.4.2.1 The range of valid VRID values on the E-Series when VRF microcode is loaded in CAM changed from 1 to 15. 8.4.
PAGE 1697
69 X.509v3 X.509v3 is a standard for public key infrastructure (PKI) to manage digital certificates and public key encryption. This standard specifies a format for public-key certificates or digital certificates. Dell EMC Networking OS supports X.509v3 standards.
PAGE 1698
crypto ca-cert install Downloads and installs the certificate of a Certificate Authority (CA) on to the device. Syntax crypto ca-cert install path Parameters path Enter the path where the CA certificate is available for download. The format that you use to specify the location of the CA certificate also includes the protocol that is used to contact the CA.
PAGE 1699
The certificate matching the current FIPS state is deleted. If the system is in FIPS mode, the FIPS certificate is deleted. If the system is in non-FIPS mode, the non-FIPS certificate is deleted. Before deleting the system’s trusted certificate, the system prompts you to specify whether to proceed with deletion. If you proceed, the system deletes the certificate and also the private key.
PAGE 1700
validity days (OPTIONAL) Enter the keyword validity followed by the number of days for which the certificate is valid. NOTE: For CSRs, validity has no effect. For self-signed certificates, if validity is not specified, it defaults to 3650 days, or 10 years. length length (OPTIONAL) Enter the keyword length followed by a bit length value. The default key length for both FIPS and non-FIPS mode is 2048. Minimum key length value for FIPS mode is 2048. The range is from 2048 to 4096.
PAGE 1701
where the certificate file is stored. Following are example of a path that you can specify: flash://certs/s4810-001-request.crtand usbflash:/certs/ s4810-001-cert.pem NOTE: Before installing a trusted certificate, you first need to download it from a remote CA using the copy command. . key-file Enter the keyword key-file to specify the private key. private Enter the keyword private to specify that the key is stored in a hidden location in the NVRAM.
PAGE 1702
Related Commands • crypto ca-cert install crypto x509 ocsp Configures the OCSP behavior. Syntax crypto x509 ocsp [nonce] [sign-requests] Parameters nonce Enter the keyword nonce to use the nonce feature for the OCSP requests to OCSP responder communication. This is a one-time value that must be returned in the OCSP response. If the OCSP responder is using precomputed responses, then it does not reply with the nonce. The nonce feature is off by default.
PAGE 1703
Related Commands Version Description 9.11.0.0 Introduced this command. • crypto x509 ocsp debug crypto This command allows you to test a certificate chain file for validity and checking revocation outside of its use in TLS communication. Syntax Parameters debug crypto {flash://path} path Enter the path to a local file where a certificate chain is stored in PEM format. Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1704
the received certificate’s sha-1 fingerprint against this configured sha-1 fingerprint. If present, only the fingerprint is used for certificate revocation validation. port port-number Enter the keyword port followed by the port number. The default port number is 6514 for secure logging. Defaults None. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide.
PAGE 1705
When you use this command, the device maps the current certificate context in the certificate store to a CA certificate through the subject key identifier field. The subject key identifier field contains the SHA-1 hash of the CA’s public key. This configuration provides a way to uniquely identify a CA and associate it with any CA-specific settings. This context is used to store certificate-specific settings such as alternate CRL and OCSP locations. Incoming X.
PAGE 1706
Defaults None. Command Modes CERTIFICATE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Version Description 9.11.0.0 Introduced this command.
PAGE 1707
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. The following is a list of the Dell EMC Networking OS version history for this command: Version Description 9.11.0.0 Introduced this command. Usage Information The following RBAC roles are allowed to issue this command: Related Commands • • sysadmin secadmin • crypto cert install X.