Users Guide

• The switch can obtain a dynamically assigned IP address from a DHCP server. A start-up configuration is not received. Use bare metal
provisioning (BMP) to receive configuration parameters (Dell Networking OS version and a configuration file). BMP is enabled as a
factory-default setting on a switch.
A switch cannot operate with BMP and as a DHCP client simultaneously. To disable BMP in EXEC mode, use the stop bmp
command. After BMP stops, the switch acts as a DHCP client.
• Acquire a dynamic IP address from a DHCP client is for a limited period or until the client releases the address.
• A DHCP server manages and assigns IP addresses to clients from an address pool stored on the server. For more information, refer to
Configuring the Server for Automatic Address Allocation.
• Dynamically assigned IP addresses are supported on Ethernet, VLAN, and port-channel interfaces.
• The public out-of-band management interface and default VLAN 1 are configured by default as a DHCP client to acquire a dynamic IP
address from a DHCP server.
• By default, the switch is configured to operate in BMP mode as a DHCP client that sends DHCP requests to a DHCP server to
retrieve configuration information (IP address, boot-image filename, and configuration file). All ports and management interfaces are
brought up in Layer 3 mode and pre-configured with no shutdown and no ip address. For this reason, you cannot enter
configuration commands to set up the switch. To interrupt a BMP process, prevent a loop from occurring, and apply the Dell
Networking OS image and startup configuration stored in the local flash, enter the stop bmp command from the console. To
reconfigure the switch so that it boots up in normal mode using the Dell Networking OS image and startup configuration file in local
flash, enter the reload-type normal-reload command and save it to the startup configuration:
Dell# reload-type normal-reload
Dell# write memory
Dell# reload
• To re-enable BMP mode for the next reload, enter the reload-type jump-start command.
Configuring the DHCP Client System
This section describes how to configure and view an interface as a DHCP client to receive an IP address.
Dell Networking OS Behavior: The ip address dhcp command enables DHCP server-assigned dynamic addresses on an interface.
The setting persists after a switch reboot. To stop DHCP transactions and save the dynamically acquired IP address, use the shutdown
command on the interface. To display the dynamic IP address and show DHCP as the mode of IP address assignment, use the show
interface type slot/port[/subport] command. To unconfigure the IP address, use the no shutdown command when the
lease timer for the dynamic IP address is expired. The interface acquires a new dynamic IP address from the DHCP server.
To configure a secondary (backup) IP address on an interface, use the ip address command at the INTERFACE configuration level.
Use the no ip address dhcp command to:
• Release the IP address dynamically acquired from a DHCP server from the interface.
• Disable the DHCP client on the interface so it cannot acquire a dynamic IP address from a DHCP server.
• Stop DHCP packet transactions on the interface.
When you enter the release dhcp command, the IP address dynamically acquired from a DHCP server is released from an interface.
The ability to acquire a new DHCP server-assigned address remains in the running configuration for the interface. To acquire a new IP
address, use the renew DHCP command in EXEC Privilege mode or the ip address dhcp command in INTERFACE Configuration
mode.
To manually configure a static IP address on an interface, use the ip address command. A prompt displays to release an existing
dynamically acquired IP address. If you confirm, the ability to receive a DHCP server-assigned IP address is removed.
To enable acquiring a dynamic IP address from a DHCP server on an interface configured with a static IP address, use the ip address
dhcp command. A prompt displays to confirm the IP address reconfiguration. If you confirm, the statically configured IP address is
released. An error message displays if you enter the release dhcp or renew dhcp commands.
To renew the lease time of the dynamically acquired IP, use the renew dhcp command on an interface already configured with a
dynamic IP address.
NOTE:
To verify the currently configured dynamic IP address on an interface, use the show ip dhcp lease command.
The show running-configuration command output only displays ip address dhcp. The currently assigned dynamic
IP address does not display.
To configure and view an interface as a DHCP client to receive an IP address, use the following commands.
1. Enter INTERFACE Configuration mode on an Ethernet interface.
CONFIGURATION mode
Dynamic Host Configuration Protocol (DHCP)
255