Users Guide

Configuring Route Leaking without Filtering Criteria
You can use the ip route-export tag command to export all the IPv4 routes corresponding to a source VRF. For leaking IPv6
routes, use the ipv6 route-export tag command. This action exposes source VRF's routes (IPv4 or IPv6 depending on the
command that you use) to various other VRFs. The destinations or target VRFs then import these IPv4 or IPv6 routes using the ip
route-import tag or the ipv6 route-import tag command respectively.
NOTE: In Dell Networking OS, you can configure at most one route-export per VRF as only one set of routes can be
exposed for leaking. However, you can configure multiple route-import targets because a VRF can accept routes from
multiple VRFs.
After the target VRF learns routes that are leaked by the source VRF, the source VRF in turn can leak the export target corresponding to
the destination VRFs that have imported its routes. The source VRF learns the export target corresponding to the destinations VRF using
the ip route-import tag or ipv6 route-import tag command. This mechanism enables reverse communication between
destination VRF and the source VRF.
If the target VRF contains the same prefix (either sourced or Leaked route from some other VRF), then the Leak for that particular prefix
will fail and an error-log will be thrown. Manual intervention is required to clear the unneeded prefixes. The source route will take priority
over the leaked route and the leaked route is deleted.
Consider a scenario where you have created four VRF tables VRF-red, VRF-blue, VRF-Green, and VRF-shared. The VRF-shared table
belongs to a particular service that should be made available only to VRF-Red and VRF-Blue but not VRF-Green. For this purpose, routes
corresponding VRF-Shared routes are leaked to only VRF-Red and VRF-Blue. And for reply, routes corresponding to VRF-Red and VRF-
Blue are leaked to VRF-Shared.
For leaking the routes from VRF-Shared to VRF-Red and VRF-Blue, you can configure route-export tag on VRF-shared (source VRF, who
is exporting the routes); the same route-export tag value should be configured on VRF-Red and VRF-blue as route-import tag (target
VRF, that is importing the routes). For a reply communication, VRF-red and VRF-blue are configured with two different route-export tags,
one for each, and those two values are configured as route-import tags on VRF-shared.
To configure route leaking, perform the following steps:
1. Configure VRF-shared using the following command:
ip vrf vrf-shared
interface interface-type slot/port[/subport]
ip vrf forwarding vrf-shared
ip address ip—address mask
A non-default VRF named VRF-Shared is created and the interface 1/4 is assigned to this VRF.
2. Configure the export target in the source VRF:.
ip route-export 1:1
3. Configure VRF-red.
ip vrf vrf-red
interface-type slot/port[/subport]
ip vrf forwarding VRF-red
ip address ip—address mask
A non-default VRF named VRF-red is created and the interface is assigned to this VRF.
4. Configure the import target in VRF-red.
ip route-import 1:1
5. Configure the export target in VRF-red.
ip route-export 2:2
6. Configure VRF-blue.
ip vrf vrf-blue
interface-type slot/port[/subport]
ip vrf forwarding VRF-blue
ip address ip—address mask
A non-default VRF named VRF-blue is created and the interface 1/12 is assigned to it.
7. Configure the import target in VRF-blue.
ip route-import 1:1
Virtual Routing and Forwarding (VRF)
891