Users Guide

● Enable IPsec encryption for OSPFv3 packets in Interface mode.
ipv6 ospf encryption ipsec spi number esp encryption-type
key authentication-type key
○ ipsec spi number — Enter a unique security policy index (SPI) value, from 256 to 4294967295.
○ esp encryption-type key — Enter the encryption algorithm used with ESP (3DES, DES, AES-CBC, or NULL). For
AES-CBC, only the AES-128 and AES-192 ciphers are supported.
○ key — Enter the text string used in the encryption algorithm. All neighboring OSPFv3 routers must share the key to
decrypt information. Only a non-encrypted key is supported. Required lengths of the non-encrypted key are: 3DES — 48
hex digits; DES — 16 hex digits; AES-CBC — 32 hex digits for AES-128 and 48 hex digits for AES-192.
○
authentication-type key — Enter the encryption authentication MD5 or SHA1 algorithm to use.
○ key — Enter the text string used in the authentication algorithm. All neighboring OSPFv3 routers must share the key
to exchange information. Only a non-encrypted key is supported. For MD5 authentication, the non-encrypted key must
be 32 plain hex digits. For SHA1 authentication, the non-encrypted key must be 40 hex digits. An encrypted key is not
supported.
To delete an IPsec encryption policy, use the no ipv6 ospf encryption ipsec spi number or no ipv6 ospf
encryption null command.
Configure IPsec encryption on interface
OS10(conf-if-eth1/1/1)# ipv6 ospf encryption ipsec spi 500 esp des 1234567812345678 md5
12345678123456781234567812345678
OS10(conf-if-eth1/1/1)# show configuration
!
interface ethernet1/1/1
ipv6 ospf encryption ipsec spi 500 esp des 1234567812345678 md5
12345678123456781234567812345678
no switchport
no shutdown
ipv6 address 1::1/64
Configure IPsec authentication for OSPFv3 area
Prerequisite: Before you enable IPsec authentication for an OSPFv3 area, enable OSPFv3 globally on the router.
● Enable IPsec authentication for OSPFv3 packets in an area in Router-OSPFv3 mode.
area area-id authentication ipsec spi number {MD5 | SHA1} key
○ area area-id — Enter an area ID as a number or IPv6 prefix.
○ ipsec spi number — Enter a unique security policy index (SPI) value, from 256 to 4294967295.
○ md5 — Enable message digest 5 (MD5) authentication.
○ sha1 — Enable secure hash algorithm 1 (SHA1) authentication.
○ key — Enter the text string used in the authentication type. All OSPFv3 routers in the area share the key to exchange
information. Only a non-encrypted key is supported. For MD5 authentication, the non-encrypted key must be 32 plain hex
digits. For SHA1 authentication, the non-encrypted key must be 40 hex digits. An encrypted key is not supported.
To delete an IPsec area authentication policy, use the no area area-id authentication ipsec spi number
command.
Configure IPsec authentication for an OSPfv3 area
OS10(config-router-ospfv3-100)# area 1 authentication ipsec spi 400 md5
12345678123456781234567812345678
OS10(config-router-ospfv3-100)# show configuration
!
router ospfv3 100
area 0.0.0.1 authentication ipsec spi 400 md5 12345678123456781234567812345678
IPsec encryption for OSPV3 area
Prerequisite: Before you enable IPsec encryption for an OSPFv3 area, first enable OSPFv3 globally on the router.
776
Layer 3