Reference Guide

714 | IPv4 Routing
www.dell.com | support.dell.com
Command Modes
EXEC
EXEC Privilege
Command
History
Example
FTOS#show ip cam linecard 13 port-set 0
Index Destination EC CG V C Next-Hop VId Mac-Addr Port
------ --------------- -- -- - - --------------- ---- ---------------- -------
3276 6.6.6.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP
3277 5.5.5.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP
3278 4.4.4.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP
3279 3.3.3.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP
3280 2.2.2.2 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c1 CP
11144 6.6.6.0 0 0 1 1 0.0.0.0 6 00:00:00:00:00:00 17c5 RP2
11145 5.5.5.0 0 0 1 1 0.0.0.0 5 00:00:00:00:00:00 17c5 RP2
11146 4.4.4.0 0 0 1 1 0.0.0.0 4 00:00:00:00:00:00 17c5 RP2
11147 3.3.3.0 0 0 1 1 0.0.0.0 3 00:00:00:00:00:00 17c5 RP2
11148 2.2.2.0 0 0 1 1 0.0.0.0 2 00:00:00:00:00:00 17c5 RP2
65535 0.0.0.0 0 0 1 1 0.0.0.0 0 00:00:00:00:00:00 17c5 RP2
FTOS#
summary (OPTIONAL) Enter the keyword summary to view a table listing route
prefixes and the total number of routes that can be entered into the CAM.
vrf instance (OPTIONAL) E-Series Only: Enter the keyword
vrf followed by the VRF
Instance name to show CAM information as it applies to that VRF instance.
Version 8.3.19.0 Introduced on S4820T
Version 8.3.7.0 Introduced on S4810
Version 8.1.1.2 E-Series ExaScale E600i supported
Version 8.1.1.0 Introduced on E-Series ExaScale
Version 7.9.1.0 Introduced VRF on the E-Series
Version 7.5.1.0 Introduced on C-Series
pre-Version 6.1.1.0 Introduced for E-Series
Table 24-7. show ip cam Command Example Fields
Field Description
Index Displays the CAM index number of the entry.
Destination Displays the destination route of the index.
EC Displays the number of equal cost multipaths (ECMP) available for the default
route for non-Jumbo line cards.
Displays 0,1 when ECMP is more than 8, for Jumbo line cards.
CG Displays 0.
V Displays a 1 if the entry is valid and a 0 if the entry is for a line card with Catalog
number beginning with LC-EF.
C Displays the CPU bit.
1 indicates that a packet hitting this entry is forwarded to the CP or RP2,
depending on Egress port.
Next-Hop Displays the next hop IP address of the entry.
VId Displays the VLAN ID. If the entry is 0, the entry is not part of a VLAN.