Reference Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S5000

Dell 9.7(0.0) Command Line Reference Guide

for the S5000 Switch

Summary of content (2114 pages)

PAGE 1
Dell 9.7(0.
PAGE 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
PAGE 3
Contents 1 About this Guide..................................................................................................51 Objectives............................................................................................................................................ 51 Audience.............................................................................................................................................. 51 Conventions.................................................................
PAGE 4
show startup-config........................................................................................................................... 94 show version....................................................................................................................................... 95 upgrade system................................................................................................................................... 97 upgrade...........................................................
PAGE 5
service timestamps........................................................................................................................... 140 show alarms.......................................................................................................................................141 show cam-acl-vlan........................................................................................................................... 142 show command-history...................................................
PAGE 6
show ethernet cfm mipbd................................................................................................................ 190 show ethernet cfm statistics.............................................................................................................190 show ethernet cfm port-statistics.................................................................................................... 191 show ethernet cfm traceroute-cache...........................................................
PAGE 7
ignore startup config........................................................................................................................ 223 interface management ethernet ip address.....................................................................................223 interface management port config..................................................................................................224 no default-gateway.....................................................................................
PAGE 8
Common MAC Access List Commands.......................................................................................... 268 clear counters mac access-group............................................................................................. 269 mac access-group...................................................................................................................... 269 show mac access-lists.................................................................................................
PAGE 9
set metric......................................................................................................................................311 set metric-type............................................................................................................................ 312 set next-hop................................................................................................................................ 313 set origin.................................................................
PAGE 10
deny tcp (for IPv6 ACLs)................................................................................................................... 365 deny icmp (for Extended IPv6 ACLs)................................................................................................367 deny (for IPv6 ACLs)......................................................................................................................... 369 9 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM)...........
PAGE 11
bgp bestpath med confed................................................................................................................406 bgp bestpath med missing-as-best................................................................................................. 407 bgp bestpath router-id ignore......................................................................................................... 408 bgp client-to-client reflection.....................................................................
PAGE 12
neighbor advertisement-interval...................................................................................................... 451 neighbor advertisement-start.......................................................................................................... 452 neighbor allowas-in..........................................................................................................................452 neighbor default-originate................................................................
PAGE 13
show ip bgp dampened-paths.........................................................................................................503 show ip bgp detail............................................................................................................................ 504 show ip bgp extcommunity-list....................................................................................................... 506 show ip bgp filter-list......................................................................
PAGE 14
show ip bgp community-list............................................................................................................ 554 show ip bgp dampened-paths......................................................................................................... 555 show ip bgp filter-list........................................................................................................................ 556 show ip bgp flap-statistics..............................................................
PAGE 15
show cpu-queue rate cp..................................................................................................................596 show ip protocol-queue-mapping.................................................................................................. 597 show ipv6 protocol-queue-mapping.............................................................................................. 599 show mac protocol-queue-mapping.............................................................................
PAGE 16
dcb-map stack-unit all stack-ports all.............................................................................................637 show qos dcb-map.......................................................................................................................... 638 dcb pfc-shared-buffer-size..............................................................................................................639 dcb-buffer-threshold .........................................................................
PAGE 17
ip dhcp snooping database........................................................................................................ 676 ip dhcp snooping database renew............................................................................................. 676 ip dhcp snooping trust................................................................................................................ 677 ip dhcp source-address-validation.............................................................................
PAGE 18
fip-snooping port-mode fcf............................................................................................................. 714 fip-snooping port-mode fcoe-trusted.............................................................................................715 show fip-snooping config.................................................................................................................716 show fip-snooping enode............................................................................
PAGE 19
redundancy primary..........................................................................................................................754 redundancy protocol........................................................................................................................ 755 redundancy reset-counter............................................................................................................... 756 redundancy sfm standby..............................................................
PAGE 20
duplex (10/100 Interfaces)................................................................................................................ 797 duplex (Management interface)....................................................................................................... 798 flowcontrol........................................................................................................................................799 interface........................................................................
PAGE 21
clear management application pkt-fallback-cntr..................................................................... 864 management egress-interface-selection.................................................................................. 865 show ip management-eis-route ............................................................................................... 865 show management application pkt-cntr...................................................................................
PAGE 22
show fc switch..................................................................................................................................902 show fc topology..............................................................................................................................902 show fc-trace-level.......................................................................................................................... 903 show fc zone............................................................
PAGE 23
debug ip packet.................................................................................................................................941 ip address.......................................................................................................................................... 944 ip directed-broadcast....................................................................................................................... 945 ip domain-list....................................................
PAGE 24
deny icmp....................................................................................................................................... 1004 deny tcp.......................................................................................................................................... 1005 deny udp......................................................................................................................................... 1007 ipv6 access-group..........................................
PAGE 25
ipv6 nd prefix.................................................................................................................................. 1046 ipv6 route........................................................................................................................................1048 ipv6 unicast-routing....................................................................................................................... 1050 show ipv6 cam stack-unit..........................................
PAGE 26
clear ip bgp ipv6 flap-statistics...................................................................................................... 1089 clear ip bgp ipv6 unicast soft......................................................................................................... 1090 debug ip bgp................................................................................................................................... 1091 debug ip bgp events..............................................................
PAGE 27
network backdoor...........................................................................................................................1130 redistribute....................................................................................................................................... 1131 redistribute isis................................................................................................................................. 1132 redistribute ospf..............................................
PAGE 28
neighbor distribute-list................................................................................................................... 1168 neighbor filter-list............................................................................................................................1169 neighbor maximum-prefix..............................................................................................................1170 neighbor next-hop-self..........................................................
PAGE 29
clns host.......................................................................................................................................... 1207 debug isis........................................................................................................................................ 1208 debug isis adj-packets.................................................................................................................... 1208 debug isis local-updates.......................................
PAGE 30
maximum-paths..............................................................................................................................1245 metric-style.....................................................................................................................................1246 multi-topology................................................................................................................................ 1247 net...................................................................
PAGE 31
show cam mac stack-unit.............................................................................................................. 1292 show mac-address-table............................................................................................................... 1293 show mac-address-table aging-time............................................................................................ 1296 show mac accounting access-list........................................................................
PAGE 32
show lldp neighbors..................................................................................................................1334 show lldp statistics.................................................................................................................... 1335 show management-interface...................................................................................................1336 show running-config lldp...............................................................................
PAGE 33
description...................................................................................................................................... 1369 disable..............................................................................................................................................1370 forward-delay.................................................................................................................................. 1371 hello-time................................................
PAGE 34
match ra.................................................................................................................................... 1407 mtu............................................................................................................................................ 1408 other-config-flag......................................................................................................................1409 reachable-time...............................................................
PAGE 35
priority-pgid.................................................................................................................................... 1444 priority-group bandwidth pfc.........................................................................................................1445 show fcoe-map...............................................................................................................................1447 show npiv devices.............................................................
PAGE 36
maximum-paths..............................................................................................................................1491 mib-binding.................................................................................................................................... 1492 network area................................................................................................................................... 1493 passive-interface.....................................................
PAGE 37
ipv6 ospf area............................................................................................................................ 1554 ipv6 ospf authentication........................................................................................................... 1554 ipv6 ospf bfd all-neighbors.......................................................................................................1556 ipv6 ospf cost..................................................................................
PAGE 38
ip pim neighbor-filter..................................................................................................................... 1598 ip pim query-interval...................................................................................................................... 1599 ip pim register-filter........................................................................................................................1600 ip pim rp-address..........................................................
PAGE 39
protocol spanning-tree pvst.......................................................................................................... 1639 show spanning-tree pvst................................................................................................................1640 spanning-tree pvst..........................................................................................................................1643 spanning-tree pvst err-disable..........................................................
PAGE 40
rate-shape....................................................................................................................................... 1681 service-policy input........................................................................................................................ 1682 service-policy output......................................................................................................................1683 service-queue..........................................................
PAGE 41
ip rip send version........................................................................................................................... 1723 ip split-horizon................................................................................................................................ 1724 maximum-paths.............................................................................................................................. 1725 neighbor.............................................................
PAGE 42
show spanning-tree rstp.................................................................................................................1766 spanning-tree rstp.......................................................................................................................... 1768 tc-flush-standard.............................................................................................................................1771 56 Software-Defined Networking (SDN).........................................
PAGE 43
radius-server host..................................................................................................................... 1807 radius-server vrf........................................................................................................................ 1809 radius-server key....................................................................................................................... 1810 radius-server retransmit..............................................................
PAGE 44
ip ssh rsa-authentication (Config)............................................................................................1844 ip ssh server...............................................................................................................................1845 ip ssh server vrf......................................................................................................................... 1848 ip ssh source-interface.....................................................................
PAGE 45
sflow max-header-size extended.................................................................................................. 1882 sflow polling-interval (Global)........................................................................................................1883 sflow polling-interval (Interface)....................................................................................................1884 sflow sample-rate (Global).........................................................................
PAGE 46
logging on....................................................................................................................................... 1928 logging source-interface................................................................................................................1929 logging synchronous......................................................................................................................1930 logging trap..................................................................
PAGE 47
storm-control unknown-unicast (Configuration).........................................................................1969 storm-control unknown-unicast (Interface)................................................................................. 1970 64 System Time and Date.................................................................................1972 clock summer-time date................................................................................................................
PAGE 48
67 VLAN Stacking.............................................................................................. 2007 dei enable....................................................................................................................................... 2008 dei honor........................................................................................................................................ 2008 dei mark......................................................................................
PAGE 49
delay-restore...................................................................................................................................2041 lacp ungroup member-independent............................................................................................ 2042 multicast peer-routing timeout..................................................................................................... 2043 peer-link port-channel...........................................................................
PAGE 50
show vrrp ipv6................................................................................................................................ 2081 vrrp-ipv6-group............................................................................................................................. 2083 72 Debugging and Diagnostics.......................................................................2085 Diagnostics and Monitoring Commands..............................................................................
PAGE 51
About this Guide 1 This book provides information about the Dell Networking OS command line interface (CLI). This book also includes information about the protocols and features found in Dell Networking OS.
PAGE 52
{X} Keywords and parameters within braces must be entered in the CLI. [X] Keywords and parameters within brackets are optional. x|y Keywords and parameters separated by a bar require you to choose one option. x||y Keywords and parameters separated by a double bar allows you to choose any or all of the options. Information Icons This book uses the following information symbols: NOTE: The Note icon signals important operational information.
PAGE 53
CLI Basics 2 This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Command Line When the system boots successfully, you are positioned on the command line in EXEC mode and not prompted to log in. You can access the commands through a serial console port or a Telnet session.
PAGE 54
User "Irene" on line vty3 ( 123.12.1.321 ) Dell#conf When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Navigating the CLI Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with the hostname command.
PAGE 55
community-list domain-list name domain-lookup translation domain-name fib ftp host max-frag-count assembly multicast-routing name-server pim Protocol prefix-list radius redirect-list route scp source-route options ssh tacacs telnet tftp trace-group trace-list Dell(conf)#ip Add a community list entry Domain name to complete unqualified host Enable IP Domain Name System hostname Define the default domain name FIB configuration commands FTP configuration commands Add an entry to the ip hostname table Max.
PAGE 56
Key Combination Action CNTL-N Returns to the more recent commands in the history buffer after recalling commands with Ctrl-P or the up Arrow key. CNTL-P Recalls commands, beginning with the last command. CNTL-R Re-enters the previous command. CNTL-U Deletes the line. CNTL-W Deletes the previous word. CNTL-X Deletes the line. CNTL-Z Ends continuous scrolling of the command outputs. Esc B Moves the cursor back one word. Esc F Moves the cursor forward one word.
PAGE 57
show run | grep Ethernet returns a search result with instances containing a capitalized “Ethernet,” such as interface TenGigabitEthernet 1/1 show run | grep ethernet does not return the previous search result because it only searches for instances containing a noncapitalized “ethernet” show run | grep Ethernet ignore-case returns instances containing both “Ethernet” and “ethernet” no-more does not paginate the display output save copies the output to a file for future use Displaying All Output To
PAGE 58
To enable the VRF feature and cause all VRF-related commands to be available or viewable in the CLI interface, use the following command. You must enable the VRF feature before you can configure its related attributes. Dell(conf)# feature vrf Based on whether VRF feature is identified as supported in the Feature Configuration file, configuration command feature vrf becomes available for usage. This command will be stored in running-configuration and will precede all other VRF-related configurations.
PAGE 59
Command Modes Command History EXEC EXEC Privilege Version 9.4(0.0) Introduced on the S4810, S4820T, and S6000. Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms. Example Dell#show feature Feature State -----------------------------VRF enabled Command Modes To navigate and launch various CLI modes, use specific commands.
PAGE 60
1. Verify that you are logged in to EXEC Privilege mode. 2. Enter the configure command. The prompt changes to include (conf). From this mode, you can enter INTERFACE mode by using the interface command. CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP). To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command.
PAGE 61
EIS Mode To enable or configure Egress Interface Selection (EIS), use EIS mode. To enter EIS mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the management egress-interface-selection command. The prompt changes to include (conf-mgmt-eis). You can return to CONFIGURATION mode by using the exit command. EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode.
PAGE 62
INTERFACE Mode Use INTERFACE mode to configure interfaces or IP services on those interfaces. An interface can be physical (for example, a Gigabit Ethernet port) or virtual (for example, the Null interface). To enter INTERFACE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the interface command and then enter an interface type and interface number that is available on the switch. The prompt changes to include the designated interface and slot/port number.
PAGE 63
ISIS ADDRESS-FAMILY Mode To enable or configure IPv6 for ISIS, use ISIS ADDRESS-FAMILY mode. For more information, refer to Intermediate System to Intermediate System (IS-IS). To enter ISIS ADDRESS-FAMILY mode: 1. Verify that you are logged in to ROUTER ISIS mode. 2. Enter the command address-family ipv6 unicast. The prompt changes to include (confrouter_isis-af_ipv6). LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode.
PAGE 64
2. Use the mac access-list standard or mac access-list extended command. Include a name for the ACL. The prompt changes to include (conf-std-macl) or (conf-ext-macl). You can return to CONFIGURATION mode by using the exit command. MONITOR SESSION Mode To enable and configure a traffic monitoring session using port monitoring, use MONITOR SESSION mode. For more information, refer to Port Monitoring. To enter MONITOR SESSION mode: 1. Verify that you are logged in to CONFIGURATION mode. 2.
PAGE 65
PORT-CHANNEL FAILOVER-GROUP Mode To configure shared LAG state tracking, use PORT-CHANNEL FAILOVER-GROUP mode. For more information, refer to Port Channel Commands. To enter PORT-CHANNEL FAILOVER-GROUP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the port-channel failover-group command. The prompt changes to include (conf-pofailover-grp). You can return to CONFIGURATION mode by using the exit command. PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode.
PAGE 66
2. Use the route-map map-name [permit | deny] [sequence-number] command. The prompt changes to include (config-route-map). You can return to CONFIGURATION mode by using the exit command. ROUTER BGP Mode To enable and configure Border Gateway Protocol (BGP), use ROUTER BGP mode. For more information, refer to Border Gateway Protocol IPv4 (BGPv4) To enter ROUTER BGP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the router bgp command then enter the AS number.
PAGE 67
ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, refer to Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include (conf-router_rip). You can return to CONFIGURATION mode by using the exit command. SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode.
PAGE 68
1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command then enter the VRRP group ID. The prompt changes to include (conf-if-interface-type-slot/port-vrid-vrrp-group-id). Determining Chassis Mode Chassis mode in Dell Networking OS determines which hardware is being supported in an E-Series chassis.
PAGE 69
3 File Management This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. The commands in this chapter are supported by the Dell Networking OS on the S5000platform. boot system Tell the system where to access the Dell Networking OS image used to boot the system.
PAGE 70
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced the support for bmp-boot on the S-Series and Z-Series switches. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 71
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added NFS mount support. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 72
Command Modes Command History EXEC Version 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. Example copy http://admin:admin123@10.16.206.77/sample_file flash:// sample_file Related Commands copy ftp:flash Copy files from FTP server to switch copy Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field).
PAGE 73
To copy the running configuration enter the keyword running-config To copy the startup configuration enter the keyword startup-config To copy using a Secure Copy (SCP), enter the keyword scp: • If you enter scp: in the source position, enter the target URL; • If you enter scp: in the target position, first enter the source URL; To copy a file on the external FLASH enter slot0:// followed by the filename To copy a file on a TFTP server enter tftp://hostip/filepath To copy a file from an external
PAGE 74
Usage Information Version Description 7.6.1.0 Introduced on the S-Series and added the SSH port number to the SCP prompt sequence on all systems. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell Networking OS supports a maximum of 100 files at the root directory level, on both the internal and external Flash. When copying a file to a remote location (for example, using Secure Copy [SCP]), enter only the keywords and Dell Networking OS prompts you for the rest of the information.
PAGE 75
Example Dell#copy running-config nfsmount:///filepath Destination file name [test.txt]: User name to login remote host: usrname Password to login remote host: Example Dell#copy scp: flash: Address or name of remote host []: 10.11.199.134 Port number of the server [22]: 99 Source file name []: test.cfg User name to login remote host: admin Password to login remote host: Destination file name [test.cfg]: test1.
PAGE 76
no-confirm (OPTIONAL) Enter the keyword no-confirm to specify that Dell Networking OS does not require user input for each file prior to deletion. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON.
PAGE 77
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for NFS mount. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 78
format flash (S-Series) Erase all existing files and reformat the filesystem in the internal flash memory. After the filesystem is formatted, files cannot be restored. Syntax format flash: Defaults flash memory Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 79
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Introduced on S4810 and Z9000. 8.3.19.0 Introduced on S4820T.
PAGE 80
Example Dell#mkdir nfsmount:/nfs-mountpoint/guest Related Commands rmdir – removes a directory. mount nfs Mounts an NFS file system to a device. Syntax mount nfs rhost:path mount-point [username password] Parameters Enter the following location keywords and information: rhost:path Enter the remote hosts’s path directory. mount-point Enter the folder name in the local file system. username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password.
PAGE 81
The following is a list of the Dell Networking OS version history for this command. Version 9.7(0.0) Introduced this command. Example Dell#rmdir nfsmount:/nfs-mountpoint/guest Proceed to remove the directory [confirm yes/no]: yes Dell# Related Commands mkdir – creates a directory. rename Rename a file in the local file system. Syntax Parameters rename url url url Enter the following keywords and a filename: • For a file on the internal Flash, enter flash:// followed by the filename.
PAGE 82
Version Description E-Series Original command restore factory-defaults Restore factory defaults. Syntax Parameters restore factory-defaults stack-unit {0-5 | all} {clear-all | bootvar | nvram} factorydefaults Return the system to its factory default mode. 0-5 Enter the stack member unit identifier to restore only the mentioned stack-unit. all Enter the keyword all to restore all units in the stack. bootvar Enter the keyword bootvar to reset boot line.
PAGE 83
When restoring all units in a stack, all the units in the stack are placed into standalone mode. When restoring a single unit in a stack, that unit placed in stand-alone mode. No other units in the stack are affected. When restoring units in stand-alone mode, the units remain in stand-alone mode after the restoration. After the restore is complete, the units power cycle immediately. CAUTION: There is no undo for this command.
PAGE 84
Unit Nvram Config -----------------------0 Success Success 1 Success Success 2 Success Success 3 Not present 4 Not present 5 Not present Power-cycling the unit(s). Dell# Example (single stack) Dell#restore factory-defaults stack-unit 0 clear-all ************************************************************** * Warning - Restoring factory defaults will delete the existing * * startup-config and all persistent settings (stacking, fanout, etc.)* * After restoration the unit(s) will be powercycled immediately.
PAGE 85
************************************************************** Proceed with factory settings? Confirm [yes/no]:yes -- Restore status -Unit Nvram Config -----------------------1 Success Power-cycling the unit(s). Dell# show boot system Displays information about boot images currently configured on the system.
PAGE 86
Stack-unit 1 [boot] Dell# FLASH BOOT 9-0(2-1) 9-0(2-0) show bootvar Display the variable settings for the boot parameters. Syntax show bootvar Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example 86 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.
PAGE 87
show file-systems Display information about the file systems on the system. Syntax show file-systems Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Command Fields Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 88
Field Description • Prefixes Related Commands w = write access Displays the name of the storage location. format flash (S-Series) – Erases all the existing files and reformats the filesystem in the internal flash memory on the S-Series. show os-version Display the release and software image version information of the image file specified.
PAGE 89
Example Version Description E-Series Original command.
PAGE 90
acl for the current ACL configuration arp for the current static ARP configuration as-path for the current AS-path configuration bfd for the current BFD configuration bgp for the current BGP configuration boot for the current boot configuration cam-profile for the current CAM profile in the configuration class-map for the current class-map configuration communitylist for the current community-list configuration ecmp-group for the current ECMP group configuration eis for the current
PAGE 91
File Management isis for the current ISIS configuration line for the current line configuration lldp for the current LLDP configuration load-balance for the current port-channel loadbalance configuration logging for the current logging configuration mac for the current MAC ACL configuration mac-addresstable for the current MAC configuration managementeis for the current management EIS configuration managementroute for the current Management port forwarding configuration mld for the curre
PAGE 92
resolve for the current DNS configuration rip for the current RIP configuration rmon for the current RMON configuration route-map for the current route map configuration sflow for the current sFlow configuration snmp for the current SNMP configuration spanningtree for the current spanning tree configuration static for the current static route configuration status for the file status information tacacs+ for the current TACACS+ configuration tftp for the current TFTP configuration trace-
PAGE 93
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for the tunnel and EIS interface types. 9.0.0.0 Added support for the VLT option. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the hardware-monitor option. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 94
Usage Information The status option allows you to display the size and checksum of the running configuration and the startup configuration. show startup-config Display the startup configuration. Syntax show startup-config Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 95
show version Display the current Dell Networking Operating System (OS) version information on the system. Syntax show version Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Command Fields File Management Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 96
Example (SSeries) Lines Beginning With Description 1 Route Processor... Hardware configuration of the system, including the number and type of physical interfaces available Dell#show version Dell Real Time Operating System Software Dell Operating System Version: 1.0 Dell Application Software Version: E7-8-1-13 Copyright (c) 1999-2008 by Dell Force10 Networks, Inc.
PAGE 97
upgrade system Upgrade the Dell Networking OS image. To upgrade the bootflash or bootselector image, use the upgrade boot command. Syntax Parameters upgrade system {flash: | ftp: | nfsmount: | scp: | stack-unit {stack-unit-id | all} | tftp: | | usbflash:} file-url {A: |B:} system Enter the keyword system to upgrade the operating system (OS) image.
PAGE 98
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.7(0.0) Added support for NFS mount. Version 9.2(1.0) Introduced on the Z9500. Version 9.0(0.0) Added support for IPv6 for the file-url parameter. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for TFTP and SCP. Version 7.6.1.
PAGE 99
Parameters boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image. ftp: After entering the keyword ftp:, you can either follow it with the location of the source file in this form: // userid:password@hostip/filepath or press Enter to launch a prompt sequence.
PAGE 100
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0(0.0) Added support for IPv6 for the file-url parameter. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only.
PAGE 101
..................................... ............................................................... ..................................... ....................................
PAGE 102
4 Control and Monitoring This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP). NOTE: This command replaces the enable optic-info-update interval command to update information on temperature and power monitoring in the simple network management protocol (SNMP) management information base (MIB).
PAGE 103
Usage Information You must save the configuration and reload the system to implement ASF. When you enter the command, the system sends a message stating that the new mode is enabled when the system reloads. banner exec Configure a message that is displayed when your enter EXEC mode. Syntax banner exec c line c To delete a banner, use the no banner exec command. Parameters c Enter the keywords banner exec, then enter a character delineator, represented here by the letter c. Press ENTER.
PAGE 104
banner and prompt appear. After the user has logged in, the banner EXEC (if configured) displays. Example Dell(conf)#banner exec ? LINE c banner-text c, where 'c' is a delimiting character Dell(conf)#banner exec % Enter TEXT message. End with the character '%'. This is the banner% Dell(conf)#end Dell#exit 4d21h5m: %RPM0-P:CP %SEC-5-LOGOUT: Exec session is terminated for user on line console This is the banner Dell con0 now available Press RETURN to get started.
PAGE 105
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.2.1.
PAGE 106
This is the banner Dell> Related Commands banner motd — sets a Message of the Day banner. banner exec — enables the display of a text string when you enter EXEC mode. banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%).
PAGE 107
configured, it displays first. If no message of the day banner is configured, the login banner and prompt appear. After the user has logged in, the banner EXEC (if configured) displays. Related Commands banner exec — enables the display of a text string when you enter EXEC mode. banner login — sets a banner to display after successful login to the system. cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 108
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2(0.2) Added support for the fcoe parameter on the S4810 and S4820T. 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.
PAGE 109
cam-acl-vlan Specify the number of VFP blocks allocated to OpenFlow. Syntax cam-acl-vlan vlanopenflow {0|1} vlaniscsi {0|1} Defaults Disabled. Parameters vlanopenflow Enter the number 1 to allocate VFP blocks and enable OpenFlow. (Default) Enter the number 0 to disable OpenFlow. vlaniscsi Enter the number 1 to allocate VFP blocks for iSCSI. Enter the number 0 to disable iSCSI CAM allocation. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 110
console 0 Enter the keywords console 0 to reset the console port. vty number Enter the keyword vty then a number to clear a terminal line. The range is from 0 to 9. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON.
PAGE 111
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell#configure Dell(conf)# disable Return to EXEC mode. Syntax Parameters disable [level] level (OPTIONAL) Enter a number for a privilege level of the Dell Networking OS.
PAGE 112
Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax Parameters do command command Enter an EXEC-level command. Defaults none Command Modes • CONFIGURATION • INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 113
Example Dell(conf-if-te-5/1)#do clear counters Clear counters on all interfaces [confirm] Dell(conf-if-te-5/1)# Dell(conf-if-te-5/1)#do clear logging Clear logging buffer [confirm] Dell(conf-if-te-5/1)# Dell(conf-if-te-5/1)#do reload System configuration has been modified. Save? [yes/no]: n Proceed with reload [confirm yes/no]: n enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password.
PAGE 114
Usage Information Users entering EXEC Privilege mode or any other configured privilege level can access configuration commands. To protect against unauthorized access, use the enable password command to configure a password for the enable command at a specific privilege level. If no privilege level is specified, the default is privilege level 15. NOTE: If you are authorized for the EXEC Privilege mode by your role, you do not need to enter an enable password.
PAGE 115
enable xfp-power-updates Enable 10–gigabit small form-factor pluggable (XFP) power updates for SNMP. Syntax Parameters enable xfp-power-updates interval seconds interval seconds Enter the keyword interval then the polling interval in seconds. The range is from 120 to 6000 seconds. Default: 300 seconds (5 minutes). Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 116
end Return to EXEC Privilege mode from other command modes (for example, CONFIGURATION or ROUTER OSPF modes). Syntax end Command Modes • CONFIGURATION • SPANNING TREE • MULTIPLE SPANNING TREE • LINE • INTERFACE • TRACE-LIST • VRRP • ACCESS-LIST • PREFIX-LIST • AS-PATH ACL • COMMUNITY-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP Command History This guide is platform-specific.
PAGE 117
exec-timeout Set a time interval that the system waits for input on a line before disconnecting the session. Syntax exec-timeout minutes [seconds] To return to default settings, use the no exec-timeout command. Parameters minutes Enter the number of minutes of inactivity on the system before disconnecting the current session. The range is from 0 to 35791. The default is 10 minutes for the console line and 30 minutes for the VTY line. seconds (OPTIONAL) Enter the number of seconds.
PAGE 118
exit Return to the lower command mode. Syntax exit Command Modes • Command History EXEC Privilege • CONFIGURATION • LINE, INTERFACE • TRACE-LIST • PROTOCOL GVRP • SPANNING TREE • MULTIPLE SPANNING TREE • MAC ACCESS LIST • ACCESS-LIST • AS-PATH ACL • COMMUNITY-LIST • PREFIX-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP This guide is platform-specific.
PAGE 119
ftp-server enable Enable FTP server functions on the system. Syntax ftp-server enable Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Control and Monitoring Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 120
ftp-server topdir Specify the top-level directory to be accessed when an incoming FTP connection request is made. Syntax Parameters ftp-server topdir directory directory Enter the directory path. Defaults The internal flash is the default directory. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 121
ftp-server username Create a user name and associated password for incoming FTP server sessions. Syntax ftp-server username username password [encryption-type] password To delete a user name and its password, use the no ftp-server username username command. Parameters username Enter a text string up to 40 characters long as the user name. password password Enter the keyword password then a string up to 40 characters long as the password.
PAGE 122
hostname Set the host name of the system. Syntax Parameters hostname name name Enter a text string, up to 32 characters long. Defaults Dell Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.
PAGE 123
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 124
password Enter a string up to 40 characters as the password. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 125
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 126
Parameters username Enter a text string as the user name up to 40 characters long. Defaults No user name is configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 127
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Use this command to make the FTP clients VRF-aware.
PAGE 128
Related Commands ip ssh server — enables the secure shell (SSH) server on the system. ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF. S5000 Syntax ip telnet server vrf {management | vrf-name} To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters vrf management Enter the keyword vrf followed by the keyword management to specify a management VRF that is used by the TELNET server.
PAGE 129
ip telnet source-interface Set an interface’s IP address as the source address in outgoing packets for Telnet sessions. Syntax ip telnet source-interface interface To return to the default setting, use the no ip telnet source-interface [interface] command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 130
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command telnet — telnet to another device. ip telnet vrf Configures a TELNET client to use a specific VRF. S5000 Syntax ip telnet [vrf vrf-name] To undo the TELENT client configuration, use the ip telnet [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TELENT client.
PAGE 131
ip tftp source-interface Assign an interface’s IP address in outgoing packets for TFTP traffic. Syntax ip tftp source-interface interface To return to the default setting, use the no ip tftp source-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 132
Version Description E-Series Original command ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TFTP client. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 133
line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. Syntax Parameters line {aux 0 |console 0 | vty number [end-number]} aux 0 Enter the keyword aux 0 to configure the auxiliary terminal connection. console 0 Enter the keyword console 0 to configure the console port. The console option for the S-Series is <0-0>.
PAGE 134
password — specifies a password for users on terminal lines. motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 135
[sweep-max-size] [sweep-interval] [ointerface (ip src-ipv4address) | interface] Parameters host (OPTIONAL) Enter the host name of the devices to which you are testing connectivity. ip-address (OPTIONAL) Enter the IPv4 address of the device to which you are testing connectivity. The address must be in the dotted decimal format. ipv6-address (OPTIONAL) Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity.
PAGE 136
validate-reply (IPv4 only) Enter Y or N for reply validation. • N: Do not validate reply data. • Y: Do validate reply data. Default is No. outgoinginterface (IPv6 link-local address) Enter the outgoing interface for ping packets to a destination link-local address. pattern pattern (IPv4 only) Enter the IPv4 data pattern. Range: 0-FFFF. Default: 0xABCD. sweep-minsize Enter the minimum size of datagram in sweep range. The range is from 52 to 15359 bytes.
PAGE 137
Usage Information Version 8.3.12.0 Added support for the outgoing-interface option for link-local IPv6 addressing on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on the ExaScale. Version 8.4.1.0 IPv6 pinging available on management interface. Version 8.3.1.0 Introduced extended ping options. Version 8.2.1.0 Introduced on the E-Series ExaScale (IPv6). Version 8.1.1.
PAGE 138
Reply to request 5 from 172.31.1.66 0 ms Reply to request 5 from 172.31.1.87 0 ms Dell# Example (IPv6) Dell#ping 100::1 Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 100::1, timeout is 2 seconds: !!!!! Success rate is 100.0 percent (5/5), round-trip min/avg/max = 0/0/0 (ms) Dell# reload Reboot Dell Networking Operating System (OS). Syntax Parameters reload [conditional nvram-cfg-change] conditional nvram-cfgchange Reload if the condition is true.
PAGE 139
changes made to the nvram, such as stack-group and fanout configurations, must be saved. send Send messages to one or all terminal line users. Syntax Parameters send [*] | [line ] | [console] | [vty] * Enter the asterisk character * to send a message to all tty lines. line Send a message to a specific line. The range is from 0 to 11. console Enter the keyword console to send a message to the primary terminal line. vty Enter the keyword vty to send a message to the virtual terminal.
PAGE 140
service timestamps To debug and log messages, add time stamps. This command adds either the uptime or the current time and date. Syntax service timestamps [debug | log] [datetime [localtime] [msec] [show-timezone] | uptime] To disable timestamping, use the no service timestamps [debug | log] command. Parameters debug (OPTIONAL) Enter the keyword debug to add timestamps to debug messages. log (OPTIONAL) Enter the keyword log to add timestamps to log messages with severity from 0 to 6.
PAGE 141
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. If you do not specify parameters and enter service timestamps, it appears as service timestamps debug uptime in the running-configuration. To view the current options set for the service timestamps command, use the show running-config command. show alarms View alarms currently active in the system.
PAGE 142
Example Dell# show alarms -- Minor Alarms -Alarm Type Duration ---------------------------------------------RPM 0 PEM A failed or rmvd 7 hr, 37 min SFM 0 PEM A failed or rmvd 7 hr, 37 min SFM 1 PEM A failed or rmvd 7 hr, 37 min SFM 2 PEM A failed or rmvd 7 hr, 37 min SFM 3 PEM A failed or rmvd 7 hr, 37 min SFM 4 PEM A failed or rmvd 7 hr, 37 min SFM 5 PEM A failed or rmvd 7 hr, 37 min SFM 6 PEM A failed or rmvd 7 hr, 37 min SFM 7 PEM A failed or rmvd 7 hr, 36 min stack-unit 1 PEM A failed or rmvd 7 hr, 36
PAGE 143
show command-history Display a buffered log of all commands all users enter along with a time stamp. Syntax show command-history Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 144
[11/20 15:47:23]: CMD-(CLI):[interface tengigabitethernet 1/1]by default from console [11/20 15:47:23]: CMD-(CLI):[ip address 1.1.1.
PAGE 145
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 146
show cpu-traffic-stats View the CPU traffic statistics. Syntax Parameters show cpu-traffic-stats [port number | all | cp ] port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568. all (OPTIONAL) Enter the keyword all to display traffic statistics on all the interfaces receiving traffic, sorted based on the traffic. cp (OPTIONAL) Enter the keyword cp to display traffic statistics on the specified CPU.
PAGE 147
Received 100% traffic on TenGigabitEthernet 8/2 Total packets: 100 LLC:0, SNAP:0, IP:100, ARP:0, other:0 Unicast:100, Multicast:0, Broadcast:0 Processor : RP1 --------------Received 62% traffic on TenGigabitEthernet 8/2 Total packets: 500 LLC:0, SNAP:0, IP:500, ARP:0, other:0 Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on TenGigabitEthernet 8/1 Total packets: 300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Processor : RP2 --------------No CPU traffic statistics
PAGE 148
ManagementEthernet 0/0 Port-channel 1-2 Port-channel 5 GigabitEthernet 4/0-3,5-6,10-11,20 GigabitEthernet 5/0-1,5-6,10-11,15,17,19,21 ICMP packet debugging is on for GigabitEthernet 5/0,2,4,6,8,10,12,14,16 Dell# show environment View S-Series and Z-Series system component status (for example, temperature or voltage). Syntax Parameters show environment [all | fan | stack-unit unit-id | pem | thermal-sensor ] all Enter the keyword all to view all components.
PAGE 149
Version Description 7.8.1.0 The output of the show environment fan command for the S-Series is changed to display fan speeds instead of showing the fan status as up or down. Usage Information The following example shows the output of the show environment command.
PAGE 150
show inventory Display the S-Series or Z-Series switch type, components (including media), and Dell Networking Operating System (OS), including hardware identification numbers and configured protocols. Syntax Parameters show inventory [media slot] media slot (OPTIONAL) Enter the keyword media then the stack ID of the stack member for which you want to display pluggable media inventory. NOTE: This parameter is available but not supported in Dell Networking Operating System version 8.3.11.4.
PAGE 151
-------------------------------------------------------------------------------------------------------------------* 0 S6000-01-FE-32T NA 08YWFG A00 CN-08YWFG-28298-39Q-0015 A00 24N1VS1 463 414 838 5 0 S6000-PWR-AC NA 0T9FNW A00 CN-0T9FNW-28298-39Q-0005 A00 NA NA 0 S6000-FAN NA 0MGDH8 A00 CN-0MGDH8-28298-39Q-0009 A00 NA NA 0 S6000-FAN NA 0MGDH8 A00 CN-0MGDH8-28298-39Q-0007 A00 NA NA 0 S6000-FAN NA 0MGDH8 A00 CN-0MGDH8-28298-39Q-0008 A00 NA NA * - Management Unit Software Protocol Configured ----------------
PAGE 152
show memory View current memory usage on the switch. Syntax Parameters show memory [stack-unit id] stack-unit id (OPTIONAL) Enter the keyword stack-unit then the stack unit ID of the S-Series stack member to display memory information on the designated stack member. The unit ID range from 0 to 11. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 153
show processes cpu Display CPU usage information based on processes running. Syntax Parameters show processes cpu [management-unit 1-99 [details] | stack-unit id | summary | [stack-unit id]] managementunit 1-99 [details] (OPTIONAL) Display processes running in the control processor. The 1-99 variable sets the number of tasks to display in order of the highest CPU usage in the past five (5) seconds. Add the keyword details to display all running processes (except sysdlp). Refer to Example (managementunit).
PAGE 154
summary | Summary of CPU utilization Pipe through a command Dell#show processes cpu summary CPU utilization 5Sec 1Min 5Min ------------------------------------------UNIT0 3% 3% 1% Dell#show processes cpu stack-unit 0 CPUID 5sec 1min 5min -------------------------------------------------CORE 0 13.17 11.53 0.00 CORE 2 9.38 12.16 0.00 Overall 11.28 11.84 0.
PAGE 155
1min - 13.37% 5min - 12.94% CoreID: 3 Process: sysdlp PID: 428 CPU usage: - 2.56% 5min - 3.40% CoreID: 0 Process: sysd PID: 410 CPU usage: - 0.96% 5min - 2.50% CoreID: 2 TID Runtime(ms) Invoked 1Min 5Min TTY Thread 56 20 2 0.00% 0.00% 0 usm 55 10 1 0.00% 0.00% 0 DHCLIENT 54 0 0 0.00% 0.00% 0 cms 53 60 6 0.00% 0.00% 0 portmirr 52 0 0 0.00% 0.00% 0 cfgDataSync 51 0 0 0.00% 0.00% 0 sysCompMgr 50 50 5 0.01% 0.00% 0 statMgr 49 1010 101 0.07% 0.08% 0 sflCp 48 30 3 0.00% 0.00% 0 snmp 47 0 0 0.00% 0.
PAGE 156
0x00000132 0.10% 0.13% 0x0000028d 0.05% 0.12% 0x000000a9 0.03% 0.06% 0x00000253 0.02% 0.02% 0x00000206 0.02% 0.03% 0x00000012 0.10% 0.12% 0x0000024d 0.08% 0.14% Related Commands 420 0 410 0 200 0 100 0 140 0 1290 0 0 400 42 vrrp 41 ovsdbsvr 20 arpm 10 otm 14 tnlmgr 129 mount_mfs 40 xstp 10000 0.20% 10000 0.20% 10000 0.20% 10000 0.20% 10000 0.20% 10000 0.00% 10000 0.00% show hardware layer2 acl — displays Layer 2 ACL data for the selected stack member and stack member port-pipe.
PAGE 157
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 158
• Example (SSeries) In the S-Series example, a retry (Retries) value of zero indicates that the SWP mechanism reached the maximum number of retransmissions without an acknowledgement. Dell#show processes ipc flow-control ? cp Control Processor | Pipe through a command show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system.
PAGE 159
Usage Information Version Description 7.6.1.0 Introduced on the S-Series.
PAGE 160
dsagt 6504 MacAgent 269778 Example (managementunit) 0 0 6504 269778 6504 269778 Dell#show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249856 50572 0 50572 50572 323 frrp 5206016 241664 369238 0 369238 369238 322 xstp 7430144 2928640 38328 0 38328 38328 321 pim 5267456 823296
PAGE 161
stack-unit unitID • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Enter the keyword stack-unit then the stack member number to display IFM information for that unit. NOTE: This option is only available on the S-Series.
PAGE 162
LACP 0 0x00000000 0x00000000 0x8000383f 0x00000000 35 DHCP 0 0x00000000 0x00000000 0x800000c2 0x0000c000 37 V6RAD 0 0x00000433 0x00030000 0x00000000 0x00000000 0 Unidentified Client0 0x006e0002 0x00000000 0x00000000 0x00000000 0 Dell# show system Display the status of all stack members or a specific member. Syntax Parameters brief (OPTIONAL) Enter the keyword brief to view an abbreviated list of system information.
PAGE 163
Version Description Version 7.8.1.0 The Boot Flash field displays the code level for boot code 2.8.1.1 and newer, while older boot codes display as "Present". Version 7.7.1.0 Added Master Priority field. Version 7.6.1.0 Introduced on the S-Series.
PAGE 164
Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.
PAGE 165
Jumbo Capable POE Capable FIPS Mode Boot Flash Boot Selector Memory Size Temperature Voltage Serial Number Part Number Vendor Id Date Code Country Code Piece Part ID PPID Revision Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : : : : : : : : : : : : : : : : yes no disabled 3.1.1.2 3.1.0.
PAGE 166
Country Code Piece Part ID PPID Revision Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : : : : NA N/A 0 disabled 00:00:00:00:00:00 3 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) -------------------------------------------------------------------------1 1 up AC up 18528 1 2 absent absent 0 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed ----------------------------------------------------------------------------------1 1 up up 19275 up 19275
PAGE 167
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 168
• • Example (SSeries) show command-history (last 20 commands) show log Dell#show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command Dell#show tech-support stack-unit 1 ? | Pipe through a command Dell#show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence of a pattern grep Show only text that matches a pattern no-more Don't paginate output save Save output to a file Dell#show tech-support sta
PAGE 169
Current Configuration ... ! Version 9-4(0-168) ! Last configuration change at Tue Mar 25 17:43:06 2014 by admin ! boot system stack-unit 0 primary tftp://10.16.127.
PAGE 170
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. telnet Connect through Telnet to a server. The Telnet client and server in Dell Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router. NOTE: The Telnet server and client are VRF-aware.
PAGE 171
• • Defaults Command Modes Command History For Tunnel interface types, enter the keyword tunnel then the slot/ port information. The range is from 1 to 16383. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Not configured. • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 172
Example Dell#telnet vrf vrf1 10.10.10.2 telnet-peer-stack-unit Open a Telnet connection to the peer stack unit. Syntax telnet-peer-stack-unit Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 173
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.
PAGE 174
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 175
4 www.Dell Networking.com (10.11.84.18) 000.000 ms 000.000 ms 000.000 ms FTOS# Example (IPv6) Dell#traceroute 100::1 Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 100::1, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 100::1 000.000 ms 000.000 ms 000.000 ms FTOS#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort.
PAGE 176
Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6address} command.
PAGE 177
Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information You can configure both IPv4 and IPv6 virtual addresses simultaneously, but only one of each. Each time this command is issued, it replaces the previously configured address of the same family, IPv4 or IPv6. The no virtual-ip command takes an address/prefix-length argument, so that the desired address only is removed.
PAGE 178
Usage Information 178 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The write memory command saves the running-configuration to the file labeled startup-configuration.
PAGE 179
5 802.1ag 802.1ag is available on the Dell Networking OS. ccm disable Disable continuity check message (CCM). Syntax ccm disable Enter no ccm disable to enable CCM. Defaults Disabled Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.
PAGE 180
Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the S-Series.
PAGE 181
Defaults 100 minutes Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series.
PAGE 182
domain Create the maintenance domain. Syntax Parameters domain name md-level number name Name the maintenance domain. md-level number Enter a maintenance domain level. The range is from 0 to 7. Defaults none Command Modes ETHERNET CFM Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 183
Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. ethernet cfm mep Create an MEP. Syntax Parameters ethernet cfm mep {up-mep | down-mep} domain {name | level} maname name mepid mep-id [up-mep | down-mep] Specify whether the MEP is up or down facing. • Up-MEP: monitors the forwarding path internal to a bridge on the customer or provider edge; on Dell Networking systems, the internal forwarding path is effectively the switch fabric and forwarding engine.
PAGE 184
ethernet cfm mip Create a maintenance intermediate point (MIP). Syntax Parameters ethernet cfm mip domain {name | level} ma-name name domain [name | level] Enter the keyword domain then the domain name or domain level. ma-name name Enter the keyword ma-name then the name of the maintenance association. Defaults none Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 185
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. mep cross-check enable Enable cross-checking. Syntax Parameters mep cross-check enable {port | vlan-id} port Down service with no VLAN association. vlan-id Enter the VLAN to apply the cross-check. Defaults none Command Modes ECFM DOMAIN Command History This guide is platform-specific.
PAGE 186
Defaults 3 ccms Command Modes ETHERNET CFM Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. ping ethernet Send a loopback message.
PAGE 187
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. show ethernet cfm domain Display maintenance domain information. Syntax Parameters show ethernet cfm domain [name | level | brief] name | level Enter the maintenance domain name or level. brief Enter the keyword brief to display a summary output.
PAGE 188
show ethernet cfm maintenance-points local Display configured MEPs and MIPs. Syntax Parameters show ethernet cfm maintenance-points local [mep | mip] mep Enter the keyword mep to display configured MEPs. mip Enter the keyword mip to display configured MIPs. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 189
show ethernet cfm maintenance-points remote Display the MEP Database. Syntax Parameters show ethernet cfm maintenance-points remote detail [active | domain {level | name} | expired | waiting] active Enter the keyword active to display only the MEPs in active state. domain [name | level] Enter the keyword domain then the domain name or domain level. expired Enter the keyword expired to view MEP entries that have expired due to connectivity failure.
PAGE 190
show ethernet cfm mipbd Display the MIP database. Syntax show ethernet cfm mipdb Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series.
PAGE 191
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. Dell# show ethernet cfm statistics Domain Name: Customer Domain Level: 7 MA Name: My_MA MPID: 300 CCMs: Transmitted: LTRs: Unexpected Rcvd: LBRs: Received: Received Bad MSDU: Transmitted: 1503 RcvdSeqErrors: 0 0 0 0 0 Rcvd Out Of Order: 0 show ethernet cfm port-statistics Display CFM statistics by port.
PAGE 192
show ethernet cfm traceroute-cache Display the link trace cache. Syntax show ethernet cfm traceroute-cache Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.
PAGE 193
Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series.
PAGE 194
traceroute cache size Set the size of the link trace cache. Syntax Parameters traceroute cache size entries entries Enter the number of entries the link trace cache can hold. The range is from 1 to 4095 entries. Defaults 100 entries Command Modes ETHERNET CFM Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 195
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. 802.1ag Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series.
PAGE 196
6 802.1X An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking operating software supports remote authentication dial-in service (RADIUS) and active directory environments using 802.1X Port Authentication.
PAGE 197
debug dot1x Display 802.1X debugging information. Syntax Parameters debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] all Enable all 802.1X debug messages. auth-pae-fsm Enable authentication PAE FSM debug messages. backend-fsm Enable backend FSM debug messages. eapol-pdu Enable the EAPOL frame trace and related debug messages. interface interface Restricts the debugging information to an interface.
PAGE 198
Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts followed number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 199
dot1x auth-server Configure the authentication server to RADIUS. Syntax dot1x auth-server radius Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 200
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. The prerequisites for enabling MAB-only authentication on a port are: • Enable 802.1X authentication globally on the switch and on the port (the dot1x authentication command). • Enable MAC authentication bypass on the port (the dot1x mac-auth-bypass command).
PAGE 201
Related Commands Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series TeraScale. dot1x authentication (Interface) — Enables dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface. Enable dot1x both globally and at the interface level.
PAGE 202
dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable. Syntax dot1x guest-vlan vlan-id To disable the guest VLAN, use the no dot1x guest-vlan vlan-id command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 203
Related Commands • dot1x auth-fail-vlan — Configure an authentication failure VLAN. • dot1x reauthentication — Enable periodic re-authentication of the client. • dot1x reauth-max — Configure the maximum number of times to re-authenticate a port before it becomes unauthorized dot1x host-mode Enable single-host or multi-host authentication. Syntax Parameters dot1x host-mode {single-host | multi-host | multi-auth} single-host Enable single-host authentication.
PAGE 204
• Related Commands Multi-supplicant mode authenticates every device attempting to connect to the network on the authenticator port. show dot1x interface — Display the 802.1X configuration of an interface. dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell Networking OS attempts to authenticate the host based on its MAC address.
PAGE 205
dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command. Parameters number Enter the number of times an EAP request is transmitted before a session time-out. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 206
Defaults 128 hosts can be authenticated on a single authenticator port. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 207
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator completes authentication only when you set port-control to auto.
PAGE 208
Version Description 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic reauthentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic reauthentication, use the no dot1x reauthentication command. Parameters interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which reauthentication is initiated. The range is from 1 to 31536000 (one year). The default is 3600 (1 hour).
PAGE 209
dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 210
Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 211
Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 212
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. show dot1x cos-mapping interface Display the CoS priority-mapping table the RADIUS server provides and applies to authenticated supplicants on an 802.1X-enabled system.
PAGE 213
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. Enter a supplicant’s MAC address using the mac-address option to display CoS mapping information only for the specified supplicant. You can display the CoS mapping information applied to traffic from authenticated supplicants on 802.
PAGE 214
show dot1x interface Display the 802.1X configuration of an interface. Syntax Parameters show dot1x interface interface [mac-address mac-address] interface mac-address Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. (Optional) MAC address of a supplicant.
PAGE 215
Port Control: Port Auth Status: Re-Authentication: Untagged VLAN id: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Dell# Example (macaddress) AUTO AUTHORIZED(MAC-AUTH-BYPASS) Disable 400 Enable 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 second
PAGE 216
Dot1x Status: Port Control: Re-Authentication: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: Enable AUTO Disable Enable 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Au
PAGE 217
Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.
PAGE 218
7 Boot User Mode All commands in this chapter are available in Boot User mode on the S5000. To access this mode, press any key when the following line appears on the console during a system boot: Hit any key to stop autoboot: You enter Boot User mode immediately, as indicated by the BOOT_USER# prompt. NOTE: You cannot use the Tab key to complete commands in this mode. boot change Change the boot parameters in the operating system.
PAGE 219
boot messages disable Deactivate the NetBSD boot log. By default, the NetBSD log is disabled. S5000 Syntax boot messages disable Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. boot messages enable Enable the NetBSD boot log. By default, the NetBSD log is disabled. S5000 Syntax boot messages enable Command Modes BOOT USER Command History Usage Notes Version 9.0(1.3) Introduced on the S5000. Dell recommends that the NetBSD log remain disabled on the S5000.
PAGE 220
Number of Network Boot Config Retries is : 0 boot write net config retries Set the number of retries used for a network boot configuration failure. S5000 Syntax boot write net config retries number Command Modes BOOT USER Command History Example Version 9.0(1.3) Introduced on the S5000. BOOT_USER# boot write net config retries 2 Updated number of Network Boot Config retries to 2. boot zero Clear the primary, secondary, or default boot parameters in the operating system.
PAGE 221
Command Modes Command History BOOT USER Version 9.0(1.3) Introduced on the S5000. enable Set the access privilege level. S5000 Syntax enable {user | admin} Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. help Display the Help menu. S5000 Syntax help Command Modes BOOT USER Command History Example Boot User Mode Version 9.0(1.3) Introduced on the S5000.
PAGE 222
default-gateway default-gateway - set the default gateway ip address enable [user|admin] change access privilege level -(26%)-Use to continue, q to stop: help display help menu ignore enable-password ignore enable password ignore startup-config ignore system starup-config interface management ethernet ip address set the management port ip address and mask interface management port config 1000m set the management port at 1000m interface management port config 100m set the manageme
PAGE 223
ignore enable password Ignore the enabled password. S5000 Syntax ignore enable password Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. ignore startup config Ignore the system startup configuration. S5000 Syntax ignore startup config Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. interface management ethernet ip address Set the IP address and mask of the management port.
PAGE 224
interface management port config Set the speed or transmission mode of the management port. S5000 Syntax Parameters interface management port config {10m | 100m | 1000m | autonegotiate | no auto-negotiate | full-duplex | half-duplex} 10m Set the management port to operate at 10 Mbps. 100m Set the management port to operate at 100 Mbps. 1000m Set the management port to operate at 1000 Mbps. auto-negotiate Set the management port to auto-negotiate its speed with a peer device.
PAGE 225
no interface management ethernet ip address Clear the IP address and mask of the management port. S5000 Syntax no interface management ethernet ip address Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. reload Reload the S5000 switch. S5000 Syntax reload Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. show boot blc Display the current boot-loop counter value.
PAGE 226
show boot selection Display the currently selected bootflash partition to be used for a ROM bootstrap operation. S5000 Syntax show boot selection Command Modes BOOT USER Command History Example Version 9.0(1.3) Introduced on the S5000. BOOT_USER # show boot selection ROM BOOTSTRAP SELECTOR PARMETERS: ================================ Next ROM bootstrap set to occur from Bootflash partition A. Last ROM bootstrap occurred from Bootflash partition B.
PAGE 227
BOOT_USER # show bootvar Display information about the boot parameters used in the operating system. S5000 Syntax show bootvar Command Modes BOOT USER Command History Example Version 9.0(1.3) Introduced on the S5000.
PAGE 228
Command History Example Version 9.0(1.3) Introduced on the S5000. BOOT_USER # show default-gateway Gateway IP address: 10.11.210.63 show interface management ethernet Display the IP address and mask of the management port. S5000 Syntax show interface management ethernet Command Modes BOOT USER Command History Example Version 9.0(1.3) Introduced on the S5000. BOOT_USER # show interface management ethernet Management ethernet IP address: 10.11.210.
PAGE 229
Access Control Lists (ACL) 8 Access control lists (ACLs) are supported by the Dell Networking OS.
PAGE 230
description Enter a description of up to 80 characters. Defaults Not configured. Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 231
Related Commands show config — displays the current ACL configuration. show config Display the current ACL configuration. Syntax show config Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST Command History • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 232
Common IP ACL Commands The following commands are available within both Ingress and Egress IP ACL modes (Standard and Extended) and do not have mode-specific options. When an ACL is created without a rule and then is applied to an interface, ACL behavior reflects an implicit permit. The supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line.
PAGE 233
clear counters ip access-group Erase all counters maintained for access lists. Syntax clear counters ip access-group [access-list-name] Parameters access-listname (OPTIONAL) Enter the name of a configured access-list, up to 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 234
out Enter the keyword out to apply the ACL to outgoing traffic. implicit-permit (OPTIONAL) Enter the keyword implicit-permit to change the default action of the ACL from implicit-deny to implicit-permit (that is, if the traffic does not match the filters in the ACL, the traffic is permitted instead of dropped). vlan vlan-id (OPTIONAL) Enter the keyword vlan then the ID numbers of the VLANs. The range is from 1 to 4094 (you can use IDs from 1 to 4094). Defaults Not enabled.
PAGE 235
ip control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv4 CPU traffic. Syntax ip control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. show ip accounting access-list Display the IP access-lists created on the switch and the sequence of filters.
PAGE 236
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for the 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 237
in | out Command Modes Command History • For a VLAN interface, enter the keyword vlan followed by the slot/port number. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet followed by the slot/port information. • For a Port Channel interface, enter the keyword portchannel followed by a number. For the C-Series and SSeries, the range is 1 to 128. For the E-Series, the range is 1 to 255 for TeraScale and 1 to 512 for ExaScale.
PAGE 238
Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {source [mask] | any | host ip-address} command. source Enter the IP address in dotted decimal format of the network from which the packet was sent. any Enter the keyword any to specify that all routes are subject to the filter. You can enter any of the following keywords to specify route types. host ip-address • bytes — Enter the keyword count to count packets the filter processes.
PAGE 239
Usage Information Version Description 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only.
PAGE 240
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.1.
PAGE 241
mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. You can enter any of the following keywords to specify route types. host ip-address • bytes — Enter the keyword bytes to count bytes processed by the filter. • count — Enter the keyword count to count packets the filter processes.
PAGE 242
Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. Related Commands deny — assigns a IP ACL filter to deny IP packets.
PAGE 243
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale (IPv6). 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 244
bytes (OPTIONAL) Enter the keyword bytes to count bytes the filter processes. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255).
PAGE 245
Related Commands • The seq sequence-number command is applicable only in an ACL group. • The order option works across ACL groups that are applied on an interface via the QoS policy framework. • The order option takes precedence over seq sequence-number. • If you do not configure sequence-number, the rules with the same order value are ordered according to their configuration order. • If you configure sequence-number, the sequence-number is used as a tie breaker for rules with the same order.
PAGE 246
source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or noncontiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 247
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 248
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [dscp] [count [byte] [order] [fragments] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
PAGE 249
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.
PAGE 250
Parameters source Enter the IP address of the network or host from which the packets are sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. dscp Enter this keyword dscp to deny a packet based on the DSCP value.
PAGE 251
count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority) If you did not use the keyword order, the ACLs have the lowest order by default (255).
PAGE 252
The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to the Port Monitoring chapter. When you use the log option, the CP processor logs details the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The C-Series and S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented.
PAGE 253
To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny udp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 254
keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 255
NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt or range) may require more than one entry. The range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range.
PAGE 256
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.
PAGE 257
Parameters source Enter the IP address in dotted decimal format of the network from which the packet was sent. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address or hostname.
PAGE 258
Usage Information Version Description 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 259
any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. bit Enter a flag or combination of bits: • ack: acknowledgement field • fin: finish (no more data from the user) • psh: push function • rst: reset the connection • syn: synchronize sequence numbers • urg: urgent field dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63.
PAGE 260
order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific.
PAGE 261
When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes increment. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. Most ACL rules require one entry in the CAM.
PAGE 262
Parameters 262 • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit udp {source mask | any | host ip-address} {destination mask | any | host ip-address command. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous.
PAGE 263
Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 264
range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range. Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 265
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). 7.8.1.
PAGE 266
ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list permits all IP protocols. tcp Enter the keyword tcp to configure a TCP access list filter. udp Enter the keyword udp to configure a UDP access list filter. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.
PAGE 267
dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS order for the ACL entry. The range is from 0 to 254 (where 0 is the highest priority and 254 is the lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255).
PAGE 268
Usage Information Version Description 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. The order option is relevant in the context of the Policy QoS feature only. The following applies: • The seq sequence-number command is applicable only in an ACL group.
PAGE 269
clear counters mac access-group Clear counters for all or a specific MAC ACL. Syntax Parameters clear counters mac access-group [mac-list-name] mac-list-name (OPTIONAL) Enter the name of a configured MAC access list. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 270
NOTE: This option is available only with the keywordin option. in Enter the keyword in to configure the ACL to filter incoming traffic. out Enter the keyword out to configure the ACL to filter outgoing traffic. NOTE: The option is not available on the S-Series. NOTE: 1. If the MAC ACL is applied on VLAN, none of the VLAN members should have an access list applied for that VLAN. 2.
PAGE 271
Usage Information You can assign one ACL (standard or extended) to an interface. Related Commands mac access-list standard — configures a standard MAC ACL. mac access-list extended — configures an extended MAC ACL. show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed.
PAGE 272
show mac accounting access-list Display MAC access list configurations and counters (if configured). Syntax Parameters show mac accounting access-list access-list-name interface interface in | out access-listname Enter the name of a configured MAC ACL, up to 140 characters.
PAGE 273
Version Description 6.1.1.0 Introduced on the E-Series. Usage Information The ACL hit counters increment the counters for each matching rule, not just the first matching rule.
PAGE 274
byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. log (OPTIONAL, E-Series only) Enter the keyword log to log the packets. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide.
PAGE 275
mac access-list standard To configure a standard MAC ACL, name a new or existing MAC access control list (MAC ACL) and enter MAC ACCESS LIST mode. Also refer to the Commands Common to all ACL Types section and the Common MAC Access List Commands section. Syntax mac access-list standard mac-list-name To delete a MAC access list, use the no mac access-list standard maclist-name command. Parameters mac-list-name Enter a text string as the name of the standard MAC access list (140 character maximum).
PAGE 276
Example Dell(conf)#mac-access-list access-list standard TestMAC Dell(config-std-macl)#permit 00:00:00:00:00:00 00:00:00:00:ff:ff count Dell(config-std-macl)#deny any count permit To forward packets from a specific source MAC address, configure a filter. Syntax permit {any | mac-source-address [mac-source-address-mask]} [count [byte]] | [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 277
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 278
any Enter the keyword any to filter all packets. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match). count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes.
PAGE 279
Usage Information Version Description 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead.
PAGE 280
mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask Specify which bits in the MAC address must match. The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. macdestinationaddress Enter the destination MAC address and mask in nn:nn:nn:nn:nn:nn format. macdestinationaddress-mask Specify which bits in the MAC address must match.
PAGE 281
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs detail the packets that match.
PAGE 282
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.
PAGE 283
Related Commands mac access-list standard — configures a standard MAC access list. show mac accounting access-list — displays MAC access list configurations and counters (if configured). permit To pass packets matching the criteria specified, configure a filter.
PAGE 284
• snap - is the IEEE 802.3 SNAP frame format count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to log the packets. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 285
NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands deny — configures a MAC ACL filter to drop packets. seq — configure a MAC ACL filter with a specified sequence number. IP Prefix List Commands When you create an access-list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit.
PAGE 286
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. ip prefix-list — configures a prefix list. deny To drop packets meeting the criteria specified, configure a filter. Syntax deny ip-prefix [ge min-prefix-length] [le max-prefix-length] To delete a drop filter, use the no deny ip-prefix command. Parameters ip-prefix Specify an IP prefix in the network/length format. For example, 35.0.0.0/ 8 means match the first 8 bits of address 35.0.0.0.
PAGE 287
Usage Information Version Description 6.1.1.0 Introduced on the E-Series. Sequence numbers for this filter are automatically assigned starting at sequence number 5. If you do not use the ge or le options, only packets with an exact match to the prefix are filtered. ip prefix-list Enter the PREFIX-LIST mode and configure a prefix list. Syntax ip prefix-list prefix-name To delete a prefix list, use the no ip prefix-list prefix-name command.
PAGE 288
Related Commands show ip route list — displays IP routes in an IP prefix list. show ip prefix-list summary — displays a summary of the configured prefix lists. seq To a deny or permit filter in a prefix list while configuring the filter, assign a sequence number.
PAGE 289
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the bit mask option. If you do not use the ge or le options, only packets with an exact match to the prefix are filtered. show config Display the current PREFIX-LIST configurations.
PAGE 290
ip prefix-list snickers Dell(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. Syntax Parameters show ip prefix-list detail [prefix-name] prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 291
show ip prefix-list summary Display a summary of the configured prefix lists. Syntax Parameters show ip prefix-list summary [prefix-name] prefix-name (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 292
continue To a route-map entry with a higher sequence number, configure a route-map. Syntax Parameters continue [sequence-number] sequencenumber (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 293
• A successful match with a continue clause, the route map executes the set clauses and then goes to the specified route map entry upon execution of the continue clause. • If the next route map entry contains a continue clause, the route map executes the continue clause if a successful match occurs. • If the next route map entry does not contain a continue clause, the route map evaluates normally.
PAGE 294
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. pre-7.7.1.0 Introduced. route-map — enables a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command.
PAGE 295
Related Commands set as-path — adds information to the BGP AS_PATH attribute. match community To match routes that have a certain COMMUNITY attribute in their BGP path, configure a filter. Syntax match community community-list-name [exact] To delete a community match filter, use the no match community command. Parameters communitylist-name Enter the name of a configured community list. exact (OPTIONAL) Enter the keywords exact to process only those routes with this community list name.
PAGE 296
Parameters interface Enter the following keywords and slot/port or number information: • . • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 297
match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match ip address To match routes based on IP addresses specified in an access list, configure a filter. Syntax match ip address prefix-list-name To delete a match, use the no match ip address prefix-list-name command. Parameters prefix-listname Enter the name of configured prefix list, up to 140 characters. Defaults Not configured.
PAGE 298
match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match ip next-hop To match based on the next-hop IP addresses specified in an IP access list or IP prefix list, configure a filter. Syntax match ip next-hop {prefix-list prefix-list-name} To delete a match, use the no match ip next-hop {prefix-list prefixlist-name} command.
PAGE 299
match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match ip route-source To match based on the routes advertised by routes specified in IP access lists or IP prefix lists, configure a filter.
PAGE 300
Related Commands match interface — redistributes routes that match the next-hop interface. match ip address — redistributes routes that match an IP address. match ip next-hop — redistributes routes that match the next-hop IP address. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match metric To match on a specified value, configure a filter.
PAGE 301
match ip address — redistributes routes that match an IP address. match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. match route-type — redistributes routes that match a route type. match tag — redistributes routes that match a specific tag. match origin To match routes based on the value found in the BGP path ORIGIN attribute, configure a filter.
PAGE 302
match route-type To match routes based on the how the route is defined, configure a filter. Syntax match route-type {external [type-1 | type-2] | internal | level-1 | level-2 | local} To delete a match, use the no match route-type {local | internal | external [type-1 | type-2] | level-1 | level-2} command. Parameters external [type-1| type-2] Enter the keyword external then either type-1 or type-2 to match only on OSPF Type 1 routes or OSPF Type 2 routes.
PAGE 303
match ip next-hop — redistributes routes that match the next-hop IP address. match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match tag — redistributes routes that match a specific tag. match tag To redistribute only routes that match a specified tag value, configure a filter. Syntax match tag tag-value To remove a match, use the no match tag command.
PAGE 304
match ip route-source — redistributes routes that match routes advertised by other routers. match metric — redistributes routes that match a specific metric. match route-type — redistributes routes that match a route type. route-map Enable a route map statement and configure its action and sequence number. This command also places you in ROUTE-MAP mode.
PAGE 305
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 306
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. You can prepend up to eight AS numbers to a BGP route. This command influences best path selection in BGP by inserting a tag or AS number into the AS_PATH attribute.
PAGE 307
Related Commands Version Description pre-6.1.1.0 Introduced on the E-Series. set level — specify the OSPF area for route redistribution. set metric — specify the metric value assigned to redistributed routes. set metric-type — specify the metric type assigned to redistributed routes. set tag — specify the tag assigned to redistributed routes. set comm-list delete To remove the specified community list from the BGP route’s COMMUNITY attribute, configure a filter.
PAGE 308
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. The community list used in the set comm-list delete command must be configured so that each filter contains only one community. For example, the filter deny 100:12 is acceptable, but the filter deny 120:13 140:33 results in an error.
PAGE 309
All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. none Enter the keyword none to remove the community attribute from routes meeting the route map criteria. additive (OPTIONAL) Enter the keyword additive to add the communities to already existing communities. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 310
level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 311
To delete a BGP LOCAL_PREF attribute, use the no set local-preference command. Parameters value Enter a number as the LOCAL_PREF attribute value. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 312
metric-value Enter a number as the new metric value. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 313
type-1 Enter the keyword type-1 to assign the OSPF Type 1 metric. type-2 Enter the keyword type-2 to assign the OSPF Type 2 metric. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.
PAGE 314
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 315
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 316
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set automatic-tag — computes the tag value of the route. set level — specifies the OSPF area for route redistribution. set metric — specifies the metric value assigned to redistributed routes.
PAGE 317
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. If you do not use the set weight command, router-originated paths have a weight attribute of 32768 and all other paths have a weight attribute of zero.
PAGE 318
show route-map Display the current route map configurations. Syntax Parameters show route-map [map-name] map-name (OPTIONAL) Enter the name of a configured route map, up to 140 characters. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.
PAGE 319
AS-Path Commands The following commands configure AS-Path ACLs. ip as-path access-list Enter AS-PATH ACL mode and configure an access control list based on the BGP AS_PATH attribute. Syntax Parameters ip as-path access-list as-path-name as-path-name Enter the access-list name, up to 140 characters. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 320
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. pre-Version 6.1.1.0 Introduced on the E-Series.
PAGE 321
Example Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. pre-Version 6.1.1.0 Introduced on the E-Series. Dell(conf)#ip community-list TestComList Dell(config-community-list)# show ip community-lists Display configured IP community lists in alphabetic order.
PAGE 322
deny (for Standard IP ACLs) To drop packets with a certain IP address, configure a filter. Syntax deny {source | any | host {ip-address}}[count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [thresholdin-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {source [mask] | any | host ip-address} command.
PAGE 323
expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 324
of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 325
one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands deny tcp — Assigns a filter to deny TCP packets. deny udp — Assigns a filter to deny UDP packets. ip access-list extended — Creates an extended ACL. seq (for Standard IPv4 ACLs) Assign a sequence number to a deny or permit filter in an IP access list while creating the filter.
PAGE 326
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 327
• Parameters Defaults Use the no deny tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands.
PAGE 328
capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic.
PAGE 329
Command History Usage Information Version 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 330
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly.
PAGE 331
deny icmp (for Extended IP ACLs) To drop all or specific internet control message protocol (ICMP) messages, configure a filter. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here. For a complete description on all of the keywords and variables that are available with this command, refer the topic of this command discussed earlier in this guide.
PAGE 332
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 333
of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 334
one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). deny (for Standard MAC ACLs) To drop packets with a the MAC address specified, configure a filter.
PAGE 335
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 336
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | macdestination-address mac-destination-address-mask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 337
ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
PAGE 338
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 339
permit arp (for Extended MAC ACLs) Configure a filter that forwards ARP packets meeting this criteria. This command is supported only on 12port GE line cards with SFP optics; refer to your line card documentation for specifications.
PAGE 340
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 341
of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 342
one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). permit icmp (for Extended IP ACLs) Configure a filter to allow all or specific ICMP messages.
PAGE 343
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 344
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 345
and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists.
PAGE 346
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 347
permit (for Standard MAC ACLs) To forward packets from a specific source MAC address, configure a filter. Syntax permit {any | mac-source-address [mac-source-address-mask]} [count [byte]] | [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit {any | mac-source-address mac-sourceaddress-mask} command.
PAGE 348
new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 349
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 350
permit — configures a filter to forward packets. permit tcp (for Extended IP ACLs) To pass TCP packets meeting the filter criteria, configure a filter.
PAGE 351
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 352
Syntax seq sequence-number {deny | permit} arp {destination-macaddress mac-address-mask | any} vlan vlan-id {ip-address | any | opcode code-number} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 353
standard and extended IPv4 ACLs, standard and extended IPv6 ACLs, and standard and extended MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 354
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 355
seq (for IP ACLs) Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 356
If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 357
in which you are creating the rule is applied to the monitored interface. Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 358
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6address} [operator port [port]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 359
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 360
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 361
Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands permit – assigns a permit filter for IP packets. permit icmp (for IPv6 ACLs) To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 362
Command Modes Command History Usage Information ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 363
Parameters Defaults • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 364
You can activate flow-based monitoring for a monitoring session by entering theflow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface.
PAGE 365
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms.
PAGE 366
address} [bit] [operator port [port]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: • • Parameters Defaults Use the no seq sequence-number command syntax if you know the filter’s sequence number Use the no deny tcp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 367
standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 368
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is 5 minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information ACCESS-LIST Version Description 9.7(0.
PAGE 369
deny (for IPv6 ACLs) Configure a filter that drops IPv6 packets that match the filter criteria.
PAGE 370
expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is reenabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 371
9 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This chapter describes the access control list (ACL) VLAN group and content addressable memory (CAM) enhancements. member vlan Add VLAN members to an ACL VLAN group. Syntax Parameters member vlan {VLAN-range} VLAN-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination.
PAGE 372
ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax Parameters ip access-group {group name} out implicit-permit group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 373
Command History Version 9.3. (0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
PAGE 374
show cam-acl-vlan Display the number of flow processor (FP) blocks that is allocated for the different VLAN services. Syntax show cam-acl-vlan Command Modes EXEC Privilege Command History Usage Information Version 9.3. (0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms. After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage.
PAGE 375
VlanHp VlanFcoe : : 1 1 cam-acl-vlan Allocate the number of flow processor (FP) blocks or entries for VLAN services and processes. Syntax Parameters cam-acl-vlan { default | vlanopenflow <0-2> | vlaniscsi <0-2> | vlanaclopt <0-2> default Reset the number of FP blocks to default. By default, 0 groups are allocated for the ACL in VCAP. ACL VLAN groups or CAM optimization is not enabled by default, and you need to allocate the slices for CAM optimization.
PAGE 376
show cam-usage View the amount of CAM space available, used, and remaining in each partition (including IPv4Flow and Layer 2 ACL sub-partitions). Syntax Parameters Command Modes Command History Usage Information show cam-usage [acl | router | switch] acl (OPTIONAL) Enter the keyword acl to display Layer 2 and Layer 3 ACL CAM usage. router (OPTIONAL) Enter the keyword router to display Layer 3 CAM usage. switch (OPTIONAL) Enter the keyword switch to display Layer 2 CAM usage.
PAGE 377
Example 1: Output of the show camusage Command Example 2: Output of the show camusage acl Command Dell#show cam-usage Linecard|Portpipe| CAM Partition | Total CAM | |Available CAM ========|========|=================|=============| =============|============== 1 | 0 | IN-L2 ACL | 1008 | | 688 | | IN-L2 FIB | 32768 | | 31636 | | IN-L3 ACL | 12288 | | 12286 | | IN-L3 FIB | 262141 | | 262127 | | IN-L3-SysFlow | 2878 | | 2833 | | IN-L3-TrcList | 1024 | | 1024 | | IN-L3-McastFib | 9215 | | 9215 | | IN-L3-Qos |
PAGE 378
| 123 | | | OUT-L2 ACL | 7 | 199 Codes: * - cam usage is above 90%.
PAGE 379
| | 0 | OUT-L2 ACL | 0 | 0 show running config acl-vlan-group Display the running configuration of all or a given ACL VLAN group. Syntax Parameters show running config acl-vlan-group group name group-name Default None Command Modes EXEC Display only the ACL VLAN group that is specified. The maximum group name is 140 characters. EXEC Privilege Command History Examples Version 9.3. (0.
PAGE 380
Parameters group-name Specify the name of the ACL VLAN group. The name can contain a maximum 140 characters. Default No default behavior or values Command Modes CONFIGURATION Command History Usage Information Version 9.3(0.0) Introduced on the S4810, S4820T and Z9000 platforms You can have up to eight different ACL VLAN groups at any given time. When you configure an ACL VLAN group, you enter the ACL VLAN Group Configuration mode.
PAGE 381
Command History Version 9.3. (0.0) Introduced on the S4810, S4820T, Z9000, and MXL platforms Usage Information The output for this command displays in a line-by-line format. This allows the ACLVLAN-Group names (or the Access List Group Names) to display in their entirety. Examples The following sample output shows the line-by-line style display when using the show acl-vlan-group detail option.
PAGE 382
10 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 383
Defaults Refer to Parameters. Command Modes ROUTER OSPF ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.2.(0.
PAGE 384
Related Commands neighbor bfd disable — Explicitly disables a BFD session with a BGP neighbor or a BGP peer group. bfd disable Disable BFD on an interface. Syntax bfd disable Re-enable BFD using the no bfd disable command. Defaults BFD is disabled by default. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 385
Defaults BFD is disabled by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.
PAGE 386
Version Description 7.4.1.0 Introduced on the E-Series. bfd interval Specify non-default BFD session parameters beginning with the transmission interval. Syntax Parameters bfd interval interval min_rx min_rx multiplier value role {active | passive} interval milliseconds Enter the keywords interval to specify non-default BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 100.
PAGE 387
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Dell(conf-if-te-1/3)#bfd interval 250 min_rx 300 multiplier 4 role passive Dell(conf-if-te-1/3)# bfd neighbor Establish a BFD session with a neighbor. Syntax bfd neighbor ip-address To remove the BFD session with the neighbor, use the no bfd neighbor ipaddress command.
PAGE 388
Related Commands show bfd neighbors — displays the BFD neighbor information on all interfaces or a specified interface. bfd protocol-liveness Enable the BFD protocol liveness feature. Syntax bfd protocol-liveness Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 389
To disable BFD for all neighbors configured through static routes, use the no ip route bfd [interval interval min_rx min_rx multiplier value role {active | passive}] command. Parameters interval milliseconds (OPTIONAL) Enter the keywords interval to specify nondefault BFD session parameters beginning with the transmission interval. The range is from 50 to 1000. The default is 100.
PAGE 390
ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters. Syntax ipv6 ospf bfd all-neighbors [disable | [interval interval min_rx min_rx multiplier value role {active | passive}]] To disable all BFD sessions on an OSPFv3 interface implicitly, use the no ipv6 ospf bfd all-neighbors disable command in interface mode.. Parameters disable (OPTIONAL) Enter the keyword disable to disable BFD on this interface.
PAGE 391
Usage Information This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode. To disable BFD on a specific interface while you configure BFD in CONFIGURATION mode, use the keyword disable.
PAGE 392
Defaults See Parameters Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.0.0.0 Introduced on Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.5.1.
PAGE 393
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.
PAGE 394
peer-groupname Enter the name of the peer group that you want to explicitly disable for BFD sessions. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 395
show bfd neighbors Display BFD neighbor information on all interfaces or a specified interface. S5000 Syntax Parameters show bfd neighbors interface [detail] interface detail Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 396
* - Active session role Ad Dn - Admin Down B - BGP C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr Clients * 10.1.3.2 RemoteAddr Interface State Rx-int Tx-int Mult 10.1.3.1 Te 1/3 Up 300 Example (Detail) Dell#show bfd neighbors detail Related Commands bfd neighbor — establishes a BFD session with a neighbor. 250 3 C Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.
PAGE 397
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format (A.B.C.D). Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.
PAGE 398
Border Gateway Protocol 11 BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 399
address-family Enable the IPv4 multicast or the IPv6 address family. S5000 Syntax Parameters address-family [ipv4 {multicast | vrf vrf-name} | ipv6 unicast [vrf vrf-name]] ipv4 multicast Enter the keyword ipv4 followed by the keyword multicast to enable BGPv4 multicast mode. ipv4 vrf vrfname Enter the keyword ipv4 followed by the keyword vrf and then the name of the VRF to enable VRF mode.
PAGE 400
Version Description 6.5.1.0 Introduced aggregate-address To minimize the number of entries in the routing table, summarize a range of prefixes. S5000 Syntax Parameters aggregate-address ip-address mask [advertise-map map-name] [asset] [attribute-map map-name] [summary-only] [suppress-map mapname] ip-address mask Enter the IP address and mask of the route to be the aggregate address. Enter the IP address in dotted decimal format (A.B.C.D) and mask in /prefix format (/x).
PAGE 401
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. At least one of the routes included in the aggregate address must be in the BGP routing table for the configured aggregate to become active.
PAGE 402
bgp add-path Allow the advertisement of multiple paths for the same address prefix without the new paths replacing any previous ones. Syntax Parameters Defaults Command Modes Command History bgp add-path [send | receive | both] path-count send Enter the keyword send to indicate that the system sends multiple paths to peers. receive Enter the keyword receive to indicate that the system accepts multiple paths from peers.
PAGE 403
bgp always-compare-med Allows you to enable comparison of the MULTI_EXIT_DISC (MED) attributes in the paths from different external ASs. Syntax bgp always-compare-med To disable comparison of MED, enter no bgp always-compare-med. Defaults Disabled (that is, the software only compares MEDs from neighbors within the same AS). Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 404
To disable a dot or dot+ representation and return to ASPLAIN, enter the no bgp asnotation command. Defaults asplain Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000.
PAGE 405
Dell(conf)#do show run |grep bgp router bgp 1 bgp four-octet-as-support Dell(conf)# Related Commands bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations. Syntax bgp bestpath as-path ignore To return to the default, enter the no bgp bestpath as-path ignore command. Defaults Disabled (that is, the software considers the AS_PATH when choosing a route as best).
PAGE 406
bgp bestpath as-path multipath-relax Include prefixes received from different AS paths during multipath calculation. Syntax bgp bestpath as-path multipath-relax To return to the default BGP routing process, use the no bgp bestpath aspath multipath-relax command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 407
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 408
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 6.3.1.0 Introduced The MED is a 4-byte unsigned integer value and the default behavior is to assume a missing MED as 4294967295. This command causes a missing MED to be treated as 0. During path selection, paths with a lower MED are preferred over paths with a higher MED.
PAGE 409
Usage Information Configuring this option retains the current best-path. When sessions are then reset, the oldest received path is chosen as the best-path. bgp client-to-client reflection Allows you to enable route reflection between clients in a cluster. Syntax bgp client-to-client reflection To disable client-to-client reflection, use the no bgp client-to-client reflection command. Defaults Enabled when a route reflector is configured.
PAGE 410
bgp cluster-id Assign a cluster ID to a BGP cluster with more than one route reflector. Syntax bgp cluster-id {ip-address | number} To delete a cluster ID, use the no bgp cluster-id {ip-address | number} command. Parameters ip-address Enter an IP address as the route reflector cluster ID. number Enter a route reflector cluster ID as a number from 1 to 4294967295. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 411
Related Commands bgp client-to-client reflection — enables route reflection between the route reflector and clients. neighbor route-reflector-client — configures a route reflector and clients. show ip bgp cluster-list — views paths with a cluster ID. bgp confederation identifier Configure an identifier for a BGP confederation. Syntax bgp confederation identifier as-number To delete a BGP confederation identifier, use the no bgp confederation identifier as-number command.
PAGE 412
Usage Information To accept 4-byte formats before entering a 4-byte AS number, configure your system. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation.
PAGE 413
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 414
Parameters retry-timervalue Enter a value that denotes the time interval after which the session retries the connection. The valid range is from 10 to 65535. Defaults 60 seconds. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Introduced on the S4810.
PAGE 415
max-suppresstime (OPTIONAL) Enter the maximum number of minutes a route can be suppressed. The default is four times the half-life value. The range is from 1 to 255. The default is 60 minutes. route-map map-name (OPTIONAL) Enter the keyword route-map then the name of a configured route map. Only match commands in the configured route map are supported. Defaults Disabled. Command Modes • ROUTER BGP • ROUTER BGP-address-family Command History This guide is platform-specific.
PAGE 416
bgp default local-preference Change the default local preference value for routes exchanged between internal BGP peers. Syntax bgp default local-preference value To return to the default value, use the no bgp default local-preference command. Parameters value Enter a number to assign to routes as the degree of preference for those routes. When routes are compared, the higher the degree of preference or local preference value, the more the route is preferred. The range is from 0 to 4294967295.
PAGE 417
bgp dmzlink-bw Enables BGP Link Bandwidth. S5000 Syntax bgp dmzlink-bw To disable BGP Link Bandwidth, enter the no bgp dmzlink-bw command. Parameters dmzlink-bw Defaults N/A Command Modes ROUTER BGP Command History Usage Information Enter the keyword dmzlink-bw to enable BGP Link Bandwidth in BGP multipath. Version Description 9.7(0.0) Introduced on the S-Series.
PAGE 418
Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 419
To disable fast external failover, use the no bgp fast-external-failover command. Defaults Enabled Command Modes ROUTER BGP Command History Usage Information Version 9.0(1.3) Introduced on the S5000. The bgp fast-external-failover command appears in the show config command output. bgp four-octet-as-support Enable 4-byte support for the BGP process. Syntax bgp four-octet-as-support To disable fast external failover, use the no bgp four-octet-as-support command.
PAGE 420
Usage Information Routers supporting 4-byte ASNs advertise that function in the OPEN message. The behavior of a 4-byte router is slightly different depending on whether it is speaking to a 2-byte router or a 4-byte router. When creating Confederations, all the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. Where the 2-byte format is from 1 to 65535, the 4-byte format is from 1 to 4294967295.
PAGE 421
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. This feature is advertised to BGP neighbors through a capability advertisement. In Receiver Only mode, BGP saves the advertised routes of peers that support this capability when they restart.
PAGE 422
Usage Information To view BGP neighbor resets, use the show logging command in EXEC mode. The bgp log-neighbor-changes command appears in the show config command output. Related Commands show logging — views logging settings and system messages logged to the system. bgp non-deterministic-med Compare MEDs of paths from different autonomous systems. Syntax bgp non-deterministic-med To return to the default, use the no bgp non-deterministic-med command.
PAGE 423
When you change the path selection from Deterministic to Non-Deterministic, the path selection for the existing paths remains Deterministic until you enter the clear ip bgp command to clear existing paths. bgp recursive-bgp-next-hop Enable next-hop resolution through other routes learned by BGP. Syntax bgp recursive-bgp-next-hop To disable next-hop resolution, use the no bgp recursive-bgp-next-hop command. Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 424
Related Commands clear ip bgp — clears the ip bgp. bgp regex-eval-optz-disable Disables the Regex Performance engine that optimizes complex regular expression with BGP. Syntax bgp regex-eval-optz-disable To re-enable optimization engine, use the no bgp regex-eval-optz-disable command. Defaults Enabled Command Modes ROUTER BGP (conf-router_bgp) Command History This guide is platform-specific.
PAGE 425
and reusing regular expression evaluation results. This caching and reuse may be at the expensive of RP1 processor memory. Examples Dell(conf-router_bgp)#no bgp regex-eval-optz-disable Dell(conf-router_bgp)#do show ip protocols Routing Protocol is "ospf 22222" Router ID is 2.2.2.2 Area Routing for Networks 51 10.10.10.0/00 Routing Protocol is "bgp 1" Cluster Id is set to 10.10.10.0 Router Id is set to 10.10.10.
PAGE 426
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect.
PAGE 427
Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.2.1.0 Introduced. Usage Information When you enable soft-reconfiguration for a neighbor and you execute the clear ip bgp soft in command, the update database stored in the router is replayed and updates are re-evaluated. With this command, the replay and update process is triggered only if route-refresh request is not negotiated with the peer.
PAGE 428
Version 7.5.1.0 Related Commands Introduced capture bgp-pdu neighbor — enables capture of an IPv4 BGP neighbor packet. show capture bgp-pdu neighbor — displays BGP packet capture information for an IPv6 address. capture bgp-pdu neighbor Enable capture of an IPv4 BGP neighbor packet. Syntax capture bgp-pdu neighbor ipv4-address direction {both | rx | tx} To disable capture of the IPv4 BGP neighbor packet, use the no capture bgppdu neighbor ipv4-address command.
PAGE 429
Related Commands capture bgp-pdu max-buffer-size — specifies a size for the capture buffer. show capture bgp-pdu neighbor — displays BGP packet capture information. clear ip bgp Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection. S5000 Syntax Parameters clear ip bgp [vrf vrf-name] [* | <1–4294967295> | <0.1– 65535.65535> | A.B.C.
PAGE 430
NOTE: You must execute the clear ip bgp soft out command when ever there is a change in the local policy. If you do not run this command after a local policy change, then these policy changes are not reflected in the responses to the peer’s route refresh messages. dampening Enter the keyword dampening to clear the flap dampening information. flap-statistics Enter the keywords flap-statistics to clear the flap statistics information. ipv4 Enter the ipv4 address family to clear.
PAGE 431
clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state. S5000 Syntax Parameters clear ip bgp [vrf vrf-name] [ipv4 [multicast | unicast] | ipv6 unicast] [dampening [ipv4-address mask | ipv6–address mask] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear information on route dampening corresponding to that VRF NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF.
PAGE 432
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. After you enter this command, the software deletes the history routes and returns the suppressed routes to the Active state. The clear ip bgp dampening command does not clear the history paths. clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap.
PAGE 433
regexp regularexpression (OPTIONAL) Enter the keyword regexp then regular expressions. Use one or a combination of the following: • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pattern (0 or more sequences). • + = (plus) the sequences in a pattern (1 or more sequences). • ? = (question mark) sequences in a pattern (either 0 or 1 sequences). NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression.
PAGE 434
undebug all — disables all debugging operations. clear ip bgp peer-group Reset a peer-group’s BGP sessions. S5000 Syntax Parameters clear ip bgp [vrf vrf-name] peer-group peer-group-name [ipv4 [multicast | unicast] | ipv6 unicast] [soft {in | out}] vrf vrf-name Enter the keyword vrf and then the name of the VRF to reset the peer group corresponding to that VRF. NOTE: You can use this attribute on a specific VRF to remove history routes corresponding to that VRF.
PAGE 435
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. S5000 Syntax debug ip bgp [ vrf vrf-name | A.B.C.D | X:X:X:X::X | peer-group peer-group-name] [in | out] To disable all BGP debugging, use the no debug ip bgp command.
PAGE 436
ipv6 Enter the ipv6 IP address to view the IPV6 route information. keepalives Enter the keyword keepalives to view BGP keepalives. notifications Enter the keyword notifications to view BGP notifications. softreconfiguration Enter the keywords soft-reconfiguration to view only information on inbound BGP soft reconfiguration. updates Enter the keyword updates to view BGP updates. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 437
debug ip bgp dampening View information on routes being dampened. S5000 Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 438
debug ip bgp events Display information on local BGP state changes and other BGP events. S5000 Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] events [in | out] To disable debugging, use the no debug ip bgp [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] events [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP state changes corresponding to that VRF. A.B.C.
PAGE 439
Usage Information To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp keepalives Display information about BGP keepalive messages. S5000 Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] keepalives [in | out] To disable debugging, use the no debug ip bgp [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] keepalives [in | out] command.
PAGE 440
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. S5000 Syntax debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 441
Usage Information Version Description 9.7(0.0) Added ipv6 support. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. debug ip bgp peer-group updates View information about BGP peer-group updates.
PAGE 442
Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. S5000 Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-groupname] soft-reconfiguration To disable, use the debug ip bgp [A.B.C.D | X:X:X:X::X | peer-groupname] soft-reconfiguration command.
PAGE 443
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. This command turns on BGP soft-reconfiguration inbound debugging. If no neighbor is specified, debug turns on for all neighbors. debug ip bgp updates Allows you to view information about BGP updates. S5000 Syntax debug ip bgp [vrf vrf-name] [A.B.C.
PAGE 444
peer-groupname (OPTIONAL) Enter the name of the peer group to disable or enable all routers within the peer group. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000.
PAGE 445
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 446
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. pre-7.7.1.0 Introduced. router bgp — enters ROUTER mode on the switch.
PAGE 447
distance bgp Define an administrative distance for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command. Parameters Defaults externaldistance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internaldistance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200.
PAGE 448
are not installed in the routing table. Routes from confederations are treated as internal BGP routes. maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. S5000 Syntax maximum-paths {ebgp | ibgp} number To return to the default values, enter the no maximum-paths command. Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipath support for Internal BGP routes.
PAGE 449
neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/Subsequent Address Family Identifier). Syntax neighbor [ip-address | peer-group-name] activate To disable, use the no neighbor [ip-address | peer-group-name] activate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname (OPTIONAL) Enter the name of the peer group.
PAGE 450
neighbor add-path This command allows the specified neighbor/peer group to send/receive multiple path advertisements. Syntax Parameters neighbor [ip-address | peer-group-name] add-path [send | receive | both] path-count ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname (OPTIONAL) Enter the name of the peer group. send Enter the keyword send to indicate that the system sends multiple paths to peers.
PAGE 451
neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. Syntax neighbor {ip-address | peer-group-name} advertisement-interval seconds To return to the default value, use the no neighbor {ip-address | peergroup-name} advertisement-interval command. Parameters Defaults ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format.
PAGE 452
neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting. Syntax neighbor {ip-address} advertisement-start seconds To return to the default value, use the no neighbor {ip-address} advertisement-start command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. seconds Enter a number as the time interval, in seconds, before BGP route updates are sent. The range is from 0 to 3600 seconds.
PAGE 453
To return to the default value, use the no neighbor {ip-address | peergroup-name} allowas-in command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to set the advertisement interval for all routers in the peer group. number Enter a number of times to allow this neighbor ID to use the AS path. The range is from 1 to 10. Defaults Not configured.
PAGE 454
To remove a default route, use the no neighbor {ip-address | peergroup-name} default-originate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to set the default route of all routers in that peer group. route-map map-name (OPTIONAL) Enter the keyword route-map then the name of a configured route map. Defaults Not configured.
PAGE 455
In case of eBGP, the neighbor default-originate command does not support extended-community as a non-transtive route-map attribute. You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings.
PAGE 456
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor distribute-list Distribute BGP information via an established prefix list. Syntax neighbor {ip-address | peer-group-name} distribute-list prefixlist-name {in | out} To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 457
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Other BGP filtering commands include: neighbor filter-list, ip as-path access-list, and neighbor route-map. Related Commands neighbor route-map — assigns a route map to a neighbor or peer group. neighbor ebgp-multihop Attempt and accept BGP connections to external peers on networks that are not directly connected.
PAGE 458
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To prevent loops, the neighbor ebgp-multihop command does not install the default routes of the multihop peer. Networks not directly connected are not considered valid for best-path selection. neighbor fail-over Enable or disable fast fail-over for BGP neighbors.
PAGE 459
neighbor filter-list Configure a BGP filter based on the AS-PATH attribute. Syntax neighbor {ip-address | peer-group-name} filter-list as-pathname {in | out} To delete a BGP filter, use the no neighbor {ip-address | peer-groupname} filter-list as-path-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to apply the filter to all routers in the peer group.
PAGE 460
Related Commands ip as-path access-list — enter AS-PATH ACL mode and configure the AS-PATH filters. neighbor graceful-restart Enable graceful restart on a BGP neighbor. Syntax neighbor {ip-address | peer-group-name} graceful-restart [restart-time seconds] [stale-path-time seconds] [role receiver-only] To return to the default, enter the no bgp graceful-restart command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 461
Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. This feature advertises to BGP neighbors through a capability advertisement. In Receiver Only mode, BGP saves the advertised routes of peers that support this capability when they restart. neighbor local-as To accept external routes from neighbors with a local AS number in the AS number path, configure Internal BGP (IBGP) routers.
PAGE 462
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as.
PAGE 463
reached. If this parameter is not set, the router stops peering when the maximum number of prefixes is reached. NOTE: When you set this option, the router accepts BGP prefixes only until the maximum configured value. After the maximum number is reached, the router drops any additional prefixes that it receives. Defaults threshold = 75 Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 464
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group. Defaults Disabled. Command Modes ROUTER BGP Command History Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series.
PAGE 465
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 466
neighbor peer-group (assigning peers) Allows you to assign one peer to an existing peer group. Syntax neighbor {ip-address | peer-group peer-group-name} dmzlink-bw To delete a peer from a peer group, use the no neighbor {ip-address | peer-group peer-group-name} command. To disable dmzlink-dw for the peer group, use the no neighbor ip-address dmzlink-dw command. Parameters ip-address Enter the IP address of the router to be included in the peer group.
PAGE 467
Usage Information You can assign up to 256 peers to one peer group. When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
PAGE 468
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.
PAGE 469
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.
PAGE 470
Parameters ip-address Enter the IP address of the neighbor to enter the remote AS in its routing table. peer-groupname Enter the name of the peer group to enter the remote AS into routing tables of all routers within the peer group. number Enter a number of the AS. The range is from 0 to 65535 (2 byte) or from 1 to 4294967295 (4 byte). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 471
neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Syntax neighbor {ip-address | peer-group-name} remove-private-as To return to the default, use the no neighbor {ip-address | peer-groupname} remove-private-as command. Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers. peer-groupname Enter the name of the peer group to remove the private AS numbers. Defaults Disabled (that is, private AS number are not removed).
PAGE 472
Private AS numbers are from 64512 to 65535 (2 byte). neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} route-map map-name {in | out} To remove the route map, use the no neighbor {ip-address | peergroup-name} route-map map-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group.
PAGE 473
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted. If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used in this command.
PAGE 474
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. A route reflector reflects routes to the neighbors assigned to the cluster. Neighbors in the cluster do not need not to be fully meshed.
PAGE 475
Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-groupname Enter the name of the peer group to send a COMMUNITY attribute to all routers within the peer group. extended Optional. Enter the keyword extended to send extended community attribute. standard Optional. Enter the keyword standard to send standard community attribute. Defaults Not configured and COMMUNITY attributes are not sent to neighbors.
PAGE 476
peer-groupname Enter the name of the peer group to enable or disable all routers with in the peer group. All routers in the peer group receive routes from a route reflector. Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.0.2.
PAGE 477
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to disable or enable all routers within the peer group. Defaults Enabled (that is, BGP neighbors and peer groups are disabled.) Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 478
neighbor soft-reconfiguration inbound Enable soft-reconfiguration for BGP. Syntax neighbor {ip-address | peer-group-name} soft-reconfiguration inbound To disable, use the no neighbor {ip-address | peer-group-name} softreconfiguration inbound command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-groupname Enter the name of the peer group to disable or enable all routers within the peer group.
PAGE 479
NOTE: This command is supported in BGP Router Configuration mode for IPv4 Unicast address only. Related Commands show ip bgp neighbors — displays routes received by a neighbor. neighbor subnet Enable passive peering so that the members of the peer group are dynamic. Syntax neighbor peer-group-name subnet subnet-number mask To remove passive peering, use the no neighbor peer-group-name subnet subnet-number mask command. Parameters subnet-number Enter a subnet number in dotted decimal format (A.B.C.D.
PAGE 480
neighbor timers Set keepalive and hold time timers for a BGP neighbor or a peer group. Syntax neighbor {ip-address | peer-group-name} timers keepalive holdtime To return to the default values, use the no neighbor {ip-address | peergroup-name} timers command. Parameters Defaults ip-address Enter the IP address of the peer router in dotted decimal format. peer-groupname Enter the name of the peer group to set the timers for all routers within the peer group.
PAGE 481
Usage Information Timer values configured with the neighbor timers command override the timer values configured with any other command. When two neighbors, configured with different keepalive and holdtime values, negotiate for new values, the resulting values are as follows: • the lower of the holdtime value is the new holdtime value, and • whichever is the lower value; one-third of the new holdtime value, or the configured keepalive value, is the new keepalive value.
PAGE 482
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Loopback interfaces are up constantly and the BGP session may need one interface constantly up to stabilize the session. The neighbor update-source command is not necessary for directly connected internal BGP sessions. Neighbors are sorted according to the source and destination ip addresses.
PAGE 483
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In the Dell Networking OS best path selection process, the path with the highest weight value is preferred. NOTE: In the Dell Networking OS best-path selection process, the path with the highest weight value is preferred.
PAGE 484
• match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 485
In BGP, the next-hop for the route is calculated from the information that is acquired through IGP or static routes. Related Commands redistribute — redistributes routes into BGP. network backdoor Specify this IGP route as the preferred route. Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network.
PAGE 486
Usage Information Although Dell Networking OS does not generate a route due to the backdoor config, there is an option for injecting/sourcing a local route in the presence of network backdoor config on a learned route. permit bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to permit incoming or outgoing traffic. Syntax permit bandwidth To disable this setting, enter the no permit bandwidth command.
PAGE 487
route-map map-name (OPTIONAL) Enter the keyword route-map then the name of an established route map. Only the following ROUTE-MAP mode commands are supported: • match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 488
If you do not configure the default-metric command, in addition to the redistribute command, or there is no route map to set the metric, the metric for redistributed static and connected is “0”. To redistribute the default route (0.0.0.0/0), configure the neighbor defaultoriginate command. As BGP does not query next-hop information corresponding to locally originated routes, a local route with an unreachable next-hop is chosen as the best route.
PAGE 489
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. At least one interface must be in Layer 3 mode for the router bgp command to be accepted.
PAGE 490
During configuration, the bandwidth is specified in Mbps, not in bytes/second. While creating the actual LB extended community, the system will attach the AS number and encode the bandwidth in floating point format. show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system.
PAGE 491
PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] Outgoing packet capture enabled for BGP neighbor 20.20.20.
PAGE 492
network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.2 remote-as 200 neighbor 10.1.1.2 no shutdown show ip bgp View the current BGP IPv4 routing table for the system. S5000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 unicast] [network [networkmask] [longer-prefixes]] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view ipv4–unicast route information corresponding to that VRF.
PAGE 493
Usage Information Version Description 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. In BGP, this command displays the exact reason why the route is discarded.
PAGE 494
All the show and debugs commands display the link band width extendedcommunity prefixed with DMZ-Link-bw along with other extended communities. Dell#show ip bgp 3.3.3.0/24 BGP routing table entry for 3.3.3.0/24 Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 1.1.1.2 (3.3.3.1) Best AS_PATH : Next-Hop : 1.1.1.
PAGE 495
• ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. • $ = (dollar sign) the end of the output string. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 496
Dell#show ip bgp paths Total 2 Paths Refcount Metric Path 1 0 200 i 1 0 200 i show ip bgp cluster-list View BGP neighbors in a specific cluster. S5000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] cluster-list [cluster-id] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view cluster information of BGP neighbors corresponding to that VRF.
PAGE 497
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.
PAGE 498
Weight Path *>I 55.0.0.0/24 172.16.0.2 0 0 400 500 600 i *>I 66.0.0.0/24 172.16.0.2 0 0 500 i *>I 77.0.0.0/24 172.16.0.2 0 0 i Dell# show ip bgp community View information on all routes with Community attributes or view specific BGP community groups.
PAGE 499
no-advertise Enter the keywords no-advertise to view all routes containing the well-known community attribute of NO_ADVERTISE. All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to view all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary.
PAGE 500
Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 501
show ip bgp community-list View routes that a specific community list affects. S5000 Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] community-list community-list-name [exact-match] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes affected by a specific community list corresponding to that VRF. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 502
Usage Information The show ip bgp community-list command without any parameters lists BGP routes matching the Community List and the output is the same as for the show ip bgp command output. The following describes the show ip bgp community-list pass command shown in the following example. Example Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.
PAGE 503
show ip bgp dampened-paths View BGP routes that are dampened (non-active). S5000 Syntax Parameters Command Modes Command History show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF.
PAGE 504
The history paths that the show ip bgp command displays contain only the prefix and the next-hop information. The next-hop information shows the ip address of the neighbor. It does not show the actual next-hop details. The following describes the show ip bgp damp command shown in the following example. Example Field Description Network Displays the network ID to which the route is dampened. From Displays the IP address of the neighbor advertising the dampened route.
PAGE 505
Example Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 506
UpdNetTmrP 0 : RedistTmrP 0x41ee7094 : PeerChgTmrP 0 : CleanRibTmrP 0x41ee7104 PeerUpdTmrP 0x41ee70cc : DfrdNHTmrP 0x41ee7174 : DfrdRtselTmrP 0x41ee713c : FastExtFallover 1 : FastIntFallover 0 : Enforce1stAS 1 PeerIdBitsP 0x41967120 : softOutSz 16 : RibUpdCtxCBP 0 UpdPeerCtxCBP 0 : UpdPeerCtxAFI 0 : TcpioCtxCB 0 : RedistBlk 1 NextCBPurg 1101119536 : NumPeerToPurge 0 : PeerIBGPCnt 0 : NonDet 0 : DfrdPathSel 0 BGPRst 0 : NumGrCfg 1 : DfrdTmestmp 0 : SnmpTrps 0 : IgnrBestPthASP 0 RstOn 1 : RstMod 1 : RstRole 2
PAGE 507
Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information on all routes with extended community attributes corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes.
PAGE 508
ip extcommunity-list ecl1 permit rt 100:4 permit soo 40:4 Dell#show ip bgp extcommunity-list ecl1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop Metric Weight Path *> 55.0.0.0/24 172.16.0.2 0 200 i *> 77.
PAGE 509
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 510
ip as-path access-list a1 permit 500 Dell# Dell#show ip bgp filter-list a1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Weight Path *> 55.0.0.0/24 172.16.0.2 *> 66.0.0.0/24 172.16.0.
PAGE 511
filter-list aspath-name (OPTIONAL) Enter the keyword filter-list then the name of a configured AS-PATH ACL. The range is 140 characters. regexp regularexpression Enter a regular expression then use one or a combination of the following characters to match. The range is 256 characters. • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pattern (zero or more sequences). • + = (plus) the sequences in a pattern (one or more sequences).
PAGE 512
Usage Information Example The following describes the show ip bgp flap command shown in the following example. Field Description Network Displays the network ID to which the route is flapping. From Displays the IP address of the neighbor advertising the flapping route. Flaps Displays the number of times the route flapped. Duration Displays the hours:minutes:seconds since the route first flapped. Reuse Displays the hours:minutes:seconds until the flapped route is available.
PAGE 513
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 514
*> 3.18.135.0/24 * * * *> 4.0.0.0/8 * * * * 6.0.0.0/20 * *> * * 9.2.0.0/16 * --More-- 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.34 63.114.8.33 63.114.8.33 63.114.8.60 63.114.8.
PAGE 515
NOTE: You can use this attribute to view information exchanged by BGP neighbors that correspond to either a default or a non-default VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 516
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.
PAGE 517
The Lines Beginning with: Description BGP state Displays the neighbor’s BGP state and the amount of time in hours:minutes:seconds it has been in that state.
PAGE 518
The Lines Beginning with: Description the peering session was never reset, the word never is displayed. Example Local host: Displays the peering address of the local router and the TCP port number. Foreign host: Displays the peering address of the neighbor and the TCP port number. Dell#show ip bgp neighbors 172.16.0.2 BGP neighbor is 172.16.0.2, remote AS 200, external link Member of peer-group port0 for session parameters BGP remote router ID 172.16.0.
PAGE 519
Related Commands show ip bgp — views the current BGP routing table. show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths. S5000 Syntax show ip bgp [vrf vrf-name] next-hop Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 520
Example Field Description Flaps Displays the number of times the next hop has flapped. Time Elapsed Displays the time elapsed since the next hop was learned. If the route is down, this field displays time elapsed since the route went down. Dell# show ip bgp next-hop Next-hop Resolved 172.16.0.2 YES Dell# show ip bgp paths as-path View all unique AS-PATHs in the BGP database.
PAGE 521
Example Field Description Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these AS-Paths. AS-Path Displays the AS paths for this route, with the origin code for the route listed last. Numbers listed between braces {} are AS_SET information.
PAGE 522
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp paths community command shown in the following example. Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored.
PAGE 523
ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. peer-groupname (OPTIONAL) Enter the name of a peer group to view information about that peer group only. detail (OPTIONAL) Enter the keyword detail to view detailed status information of the peers in that peer group.
PAGE 524
Example Line beginning with: Description Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported. Minimum time Displays the time interval between BGP advertisements. For address family Displays IPv4 Unicast as the address family. BGP neighbor Displays the name of the BGP neighbor.
PAGE 525
Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to view the subset of BGP routing tables that match the regular expression specified on that VRF. NOTE: You can use this attribute to view the subset of BGP routing tables that match the regular expression that is specified on either a default or a non-default VRF. regularexpression [character] Enter a regular expression then use one or a combination of the following characters to match: • .
PAGE 526
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp regexp command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then non-BGP routes exist in the router’s routing table.
PAGE 527
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view the status of all BGP connections corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 528
hops. If this same route is sent to a different peer, an entry for each peer is created, as the next-hop is different. As a result, the BGP attributes count in the summary output will differ accordingly. The following describes the show ip bgp summary command shown in the following example. 528 Field Description BGP router identifier Displays the local router ID and the AS number. BGP table version Displays the BGP table version and the main routing table version.
PAGE 529
Field Description Up/Down Displays the amount of time that the neighbor is in the Established stage. If the neighbor has never moved into the Established stage, the word never is displayed. The output format is: State/Pfxrcd Time Established Display Example < 1 day 00:12:23 (hours:minutes:seconds) < 1 week 1d21h (DaysHours) > 1 week 11w2d (WeeksDays) If the neighbor is in Established stage, the number of network prefixes received.
PAGE 530
show running-config bgp To display the current BGP configuration, use this feature. Syntax show running-config bgp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 531
Parameters keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds. holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 532
address family ipv4 multicast (MBGP) This command changes the context to subsequent address family identifier (SAFI). Syntax address family ipv4 multicast To remove SAFI context, use the no address family ipv4 multicast command. Parameters ipv4 Enter the keyword ipv4 to specify the address family as IPV4. multicast Enter the keyword multicast to specify multicast as SAFI. Defaults IPv4 Unicast Command Modes ROUTER BGP (conf-router_bgp) Command History Usage Information Version 7.8.1.
PAGE 533
attribute-map map-name (OPTIONAL) Enter the keywords attribute-map followed by the name of a configured route map to modify attributes of the aggregate, excluding AS_PATH and NEXT_HOP attributes. summary-only (OPTIONAL) Enter the keyword summary-only to advertise only the aggregate address. Specific routes are not advertised.
PAGE 534
Parameters half-life time (OPTIONAL) Enter the number of minutes after which the Penalty is decreased. After the router assigns a Penalty of 1024 to a route, the Penalty is decreased by half after the half-life period expires. The range is 1 to 45. The default is 15 minutes. route-map map-name (OPTIONAL) Enter the keyword route-map followed by the name of a configured route map. Only match commands in the configured route map are supported. Defaults Disabled.
PAGE 535
Version 7.7.1.0 Introduced on the C-Series. clear ip bgp dampening Clear information on route dampening. Syntax Parameters Command Modes Command History clear ip bgp dampening ipv4 multicast network network-mask dampening Enter the keyword dampening to clear route flap dampening information. network (OPTIONAL) Enter the network address in dotted decimal format (A.B.C.D). network-mask (OPTIONAL) Enter the network mask in slash prefix format (/x). EXEC Privilege Version 7.8.1.
PAGE 536
• + = (plus) the sequences in a pattern (1 or more sequences). • ? = (question mark) sequences in a pattern (either 0 or 1 sequences). NOTE: You must enter an escape sequence (CTRL+v) prior to entering the ? regular expression. Command Modes Command History • [ ] = (brackets) a range of single-character patterns. • ( ) = (parenthesis) groups a series of pattern elements to a single element. • { } = (braces) minimum and the maximum match count. • ^ = (caret) the beginning of the input string.
PAGE 537
ipv6 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view dampened-route information related only to ipv6 unicast routes. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. b Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 538
ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to reset ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to reset ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to reset ipv6 unicast routes. soft (OPTIONAL) Enter the keyword soft to reset soft configuration. in Enter the keyword in to re-configure soft inbound updates.
PAGE 539
out Defaults Disabled. Command Modes EXEC Privilege Command History (OPTIONAL) Enter the keyword out to view only BGP updates sent to neighbors. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command.
PAGE 540
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. CAUTION: Dell Networking recommends not changing the administrative distance of internal routes. Changing the administrative distances may cause routing table inconsistencies. The higher the administrative distance assigned to a route means that your confidence in that route is low.
PAGE 541
Usage Information By default, when you create a neighbor/peer group configuration in the Router BGP context, this enables IPv4/Unicast AFI/SAFI. By using activate in the new context, the neighbor/peer group enables for AFI/SAFI. Related Commands address family ipv4 multicast (MBGP) – changes the context to SAFI. neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group.
PAGE 542
neighbor default-originate Inject the default route to a BGP peer or neighbor. C-Series, E-Series TeraScale, S-Series Syntax neighbor {ip-address | peer-group-name} default-originate [route-map map-name] To remove a default route, use the no neighbor {ip-address | peergroup-name} default-originate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format.
PAGE 543
prefix-listname Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes). in Enter the keyword in to distribute only inbound traffic. out Enter the keyword out to distribute only outbound traffic. Defaults Not configured. Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.
PAGE 544
If the AS-PATH access list is not configured, the default is permit (allow routes). in Enter the keyword in to filter inbound BGP routes. out Enter the keyword out to filter outbound BGP routes. Defaults Not configured. Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 545
warning-only (OPTIONAL) Enter the keyword warning-only to set the router to send a log message when the maximum value is reached. If this parameter is not set, the router stops peering when the maximum number of prefixes is reached. Defaults threshold = 75 Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 546
neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. C-Series, E-Series TeraScale, S-Series Syntax neighbor {ip-address | peer-group-name} remove-private-as To return to the default, use the no neighbor {ip-address | peer-groupname} remove-private-as command. Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers. peer-groupname Enter the name of the peer group to remove the private AS numbers.
PAGE 547
If the Route map is not configured, the default is deny (to drop all routes). in Enter the keyword in to filter inbound routes. out Enter the keyword out to filter outbound routes. Defaults Not configured. Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 548
Command Modes Command History Usage Information ROUTER BGP Address Family (conf-router_bgp_af) Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. The first time you enter this command, it configures the neighbor as a route reflector and members of the route-reflector cluster. If you configure a route reflector, internal BGP (IBGP) speakers do not need to be fully meshed.
PAGE 549
• set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 550
• match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Address Family (conf-router_bgp_af) Command History Usage Information Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 551
match external {1 | 2} (OPTIONAL) Enter the keywords match external to redistribute OSPF external routes. You can specify 1 or 2 to redistribute those routes only. match internal (OPTIONAL) Enter the keywords match internal to redistribute OSPF internal routes only. route-map map-name (OPTIONAL) Enter the keywords route-map followed by the name of a configured route map. Defaults Not configured.
PAGE 552
Command Modes Command History Usage Information • EXEC • EXEC Privilege Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. The following describes the show ip bgp ipv4 multicast command shown the Example below.
PAGE 553
show ip bgp cluster-list View BGP neighbors in a specific cluster. C-Series, E-Series TeraScale, S-Series Syntax Parameters Command Modes Command History show ip bgp ipv4 multicast cluster-list [cluster-id] cluster-id • EXEC • EXEC Privilege (OPTIONAL) Enter the cluster id in dotted decimal format. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series.
PAGE 554
All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to view all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. Command Modes Command History Usage Information • EXEC • EXEC Privilege Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.
PAGE 555
Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. show ip bgp dampened-paths View BGP routes that are dampened (non-active). S5000 Syntax Parameters Command Modes Command History show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF.
PAGE 556
Usage Information To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event. The subsequent route-up event corresponding to the same route is not considered as a flap and is not penalized. The history paths that the show ip bgp command displays contain only the prefix and the next-hop information.
PAGE 557
Command Modes Command History • EXEC • EXEC Privilege Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. show ip bgp flap-statistics View flap statistics on BGP routes.
PAGE 558
• Command Modes Command History • EXEC • EXEC Privilege $ = (dollar sign) the end of the output string. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced IPv6 MGBP on the E-Series. show ip bgp inconsistent-as View routes with inconsistent originating AS numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path.
PAGE 559
Command Modes Command History Usage Information dampenedroutes (OPTIONAL) Enter the keywords dampened-routes to view information on dampened routes from the BGP neighbor. detail (OPTIONAL) Display detailed neighbor information. flap-statistics (OPTIONAL) Enter the keywords flap-statistics to view flap statistics on the neighbor’s routes. routes (OPTIONAL) Enter the keyword routes to view only the neighbor’s feasible routes. • EXEC • EXEC Privilege Version 7.8.1.0 Introduced on the S-Series.
PAGE 560
Example 560 Lines beginning with: Description Sent messages The line displays the number of BGP messages sent, the number of notifications (error messages) and the number of messages waiting in a queue for processing. Received updates This line displays the number of BGP updates received and sent. Minimum time Displays the minimum time, in seconds, between advertisements.
PAGE 561
Minimum time before advertisements start is 0 seconds Capabilities received from neighbor for IPv4 unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Multicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Update source set to Loopback 0 For address family: IPv4 Multicast BGP table version 14, neighbor version 14 3 accepted prefixes consume 12 bytes Prefixes accepted 1 (consume 4 bytes), withdrawn 0 by peer Prefixes advertised 0
PAGE 562
Parameters Command Modes Command History Related Commands peer-groupname (OPTIONAL) Enter the name of a peer group to view information about that peer group only. detail (OPTIONAL) Enter the keyword detail to view detailed status information of the peers in that peer group. summary (OPTIONAL) Enter the keyword summary to view status information of the peers in that peer group. The output is the same as that found in the show ip bgp summary command. • EXEC • EXEC Privilege Version 7.8.1.
PAGE 563
Usage Information The following describes the sho ip bgp ipv4 multicast summary command shown in the Example below. Field Description BGP router identifier Displays the local router ID and the AS number. BGP table version Displays the BGP table version and the main routing table version. network entries Displays the number of network entries, route paths, and the amount of memory used to process those entries.
PAGE 564
Field Description State/Pfxrcd If the neighbor is in Established stage, the number of network prefixes received. If a maximum limit was configured with the neighbor maximum-prefix command, (prfxd) appears in this column. If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm). When the peer is transitioning between states and clearing the routes received, the phrase (Purging) may appear in this column.
PAGE 565
deny To reject (deny) from the two types of extended communities, route origin (rt) or site-of-origin (soo), use this feature. Syntax deny {rt | soo} {as4 ASN4:NN | ASN:NNNN | IPADDR:NN} To remove (delete) the rule, use the no deny {rt | soo} {as4 ASN4:NN | ASN:NNNN | IPADDR:NN} command. Parameters rt Enter the keyword rt to designate a Route Origin community. soo Enter the keyword soo to designate a Site-of-Origin community (also known as Route Origin).
PAGE 566
deny regex This feature allows you to specify an extended community to reject (deny) using a regular expression (regex). Syntax deny regex {regex} To remove, use the no deny regex {regex} command. Parameters regex Enter a regular expression. Defaults Not configured. Command Modes CONFIGURATION (conf-ext-community-list) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 567
Defaults Not configured. Command Modes CONFIGURATION (conf-ext-community-list) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.0 Introduced on the E-Series.
PAGE 568
match extcommunity To match an extended community in the Route Map mode, use this feature. Syntax match extcommunity {extended community list name} To change the match, use the no match extcommunity {extended community list name} command. Parameters extended community list name Enter the name of the extended community list. Defaults none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific.
PAGE 569
Parameters rt Enter the keyword rt to designate a Route Origin community. soo Enter the keyword soo to designate a Site-of-Origin community (also known as Route Origin). as4 ASN4:NN Enter the keyword as4 then the 4-octet AS specific extended community number in the format ASN4:NN (4byte AS number:2-byte community value). ASN:NNNN Enter the 2-octet AS specific extended community number in the format ASN:NNNN (2-byte AS number:4-byte community value).
PAGE 570
Parameters regex Enter a regular expression. Defaults Not configured. Command Modes CONFIGURATION (conf-ext-community-list) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Version 7.6.1.
PAGE 571
additive (OPTIONAL) Enter the keyword additive to add to the existing extended community. non-trans (OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. Defaults none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 572
To delete the site-of-origin community, use the no set extcommunity command. Parameters as4 ASN4:NN Enter the keyword as4 then the 4-octet AS specific extended community number in the format ASN4:NN (4byte AS number:2-byte community value). ASN:NNNN Enter the 2-octet AS specific extended community number in the format ASN:NNNN (2-byte AS number:4-byte community value).
PAGE 573
show ip bgp ipv4 extcommunity-list To display the IPv4 routes matching the extended community list name, use this feature. Syntax Parameters Defaults Command Modes Command History show ip bgp [ipv4 [multicast | unicast] | ipv6 unicast] extcommunity-list name multicast Enter the keyword multicast to display the multicast route information. unicast Enter the keyword unicast to display the unicast route information.
PAGE 574
Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 100.100.1.2 (2.4.0.1) Best AS_PATH : 200 Next-Hop : 100.100.1.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref 100, Weight 0, external Communities : 300:400 500:600 Extended Communities : RT:1111:4278080 SoO:35:4 SoO:36:50529043 SoO:37:50529044 SoO:38:50529045 SoO:0.0.0.2:33 SoO:506.
PAGE 575
Example Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these extended communities. Community Displays the extended community attributes in this BGP path. Dell#show ip bgp paths extcommunity Total 1 Extended Communities Address 0x41d57024 Hash Refcount Extended Community 12272 1 RT:7:200 SoO:5:300 SoO:0.0.0.
PAGE 576
Example Dell#show ip extcommunity-list test ip extcommunity-list test deny RT:1234:12 permit regexp 123 deny regexp 234 deny regexp 123 Dell# show running-config extcommunity-list To display the current configuration of the extended community lists, use this feature. Syntax Parameters show running-config extcommunity-list [word] word Enter the name of the extended community list you want to view. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 577
Bare Metal Provisioning (BMP) 12 Bare metal provisioning (BMP) is supported on the Dell Networking OS platform. In a data center network, BMP automates the configuration and updating of switches, ensuring standard configurations across the installed devices. You can configure autoconfiguration on a single switch or on multiple switches. BMP allows you to set up a stack with a minimum of effort, but is also useful for quick configuration of a single switch.
PAGE 578
auto-save Configure the auto save option to save the downloaded configuration or script file. They are not saved by default. When auto save is configured, downloaded configurations are automatically saved to the startup configuration. Auto saving the downloaded configurations also requires enabling the config-scr-download parameter. Downloaded scripts are automatically saved to the autoexec script. config-scrdownload {enable} (Optional.
PAGE 579
Usage Information Version 9.1(0.0) Introduced on the Z9000. Updated the command mode from EXEC Privilege to GLOBAL CONFIGURATION. Updated the parameter from jumpstart to bmp. Added support for the config-scr-download and user-defined-string commands. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.1.0 Introduced on the S4810. For an initial setup, the config-scr-download parameter of the reload-type command is enabled.
PAGE 580
show reload-type Display the reload type currently configured on the system. Syntax show reload-type Defaults none Command Modes EXEC Privilege Command History To execute the post-configuration script after applying the startup configuration, Usage Information Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Updated output example to include auto-save and retrycount parameters. Version 9.1(0.0) Updated reload type parameters. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.
PAGE 581
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.1(0.0) Deprecated command. Replaced by the stop bmp command. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.4 Introduced on the Z9000.
PAGE 582
Content Addressable Memory (CAM) 13 Content addressable memory (CAM) commands are supported on the Dell Networking platform. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance. CAM Profile Commands The CAM profiling feature allows you to partition the CAM to best suit your application.
PAGE 583
cam-acl (Configuration) Select the default CAM allocation settings or reconfigure a new CAM allocation for Layer 2, IPv4, and IPv6 ACLs, Layer 2 and Layer 3 (IPv4) QoS, Layer 2 Protocol Tunneling (L2PT), IP and MAC source address validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR).
PAGE 584
l2pt number Enter the keyword l2pt and then the number of FP blocks for l2 protocol tunnelling. The range is from 0 to 1. Ipmacacl number Enter the keyword ipmacacl and then the number of FP blocks for IP and MAC ACL. The range is from 0 to 6. ecfmacl number Enter the keyword ecfmacacl and then the number of FP blocks for ECFM ACL. The range is from 0 to 5. nlbclusteracl number Enter the keyword nlbclusteracl and then the number of FP blocks for nlbcluster ACL. The range is from 0 to 2.
PAGE 585
l2acl number ipv4acl number ipv6acl number, ipv4qos number l2qos numberl2pt number ipmacacl number ecfmacl number {nlbclusteracl] [vman-qos | vman-dual-qos number] ipv4pbr numberopenflo w {4|8} | fcoe number [iscsioptacl number] [vrfv4acl number] Allocate space to each CAM region. Enter 4 or 8 for the number of OpenFlow FP blocks.
PAGE 586
Usage Information Version Description 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. Save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings to take effect. The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. Only 13 number of blocks can be configured by the user . The ipv6acl allocation must be a factor of 2.
PAGE 587
Usage Information Version 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dualqos. Version 8.2.1.0 Introduced on the S-Series. Version 7.8.1.0 Introduced on the C-Series. You must save the new CAM settings to the startup-config (write-mem or copy run start) then reload the system for the new settings to take effect. There are four groups total. You must allocate at least one group for L2ACL and IPv4 ACL. The range for the CAM profiles are 1 to 4 for l2acl.
PAGE 588
Usage Information When you enable this command, if a Policy Map containing classification rules (ACL and/or dscp/ ip-precedence rules) is applied to more than one physical interface on the same port pipe, only a single copy of the policy is written (only one FP entry is used). NOTE: An ACL itself may still require more that a single FP entry, regardless of the number of interfaces.
PAGE 589
L2PT : IpMacAcl : VmanQos : VmanDualQos : EcfmAcl : FcoeAcl : iscsiOptAcl : ipv4pbr : vrfv4Acl : Openflow : fedgovacl : nlbclusteracl: 0 0 0 0 0 0 0 0 0 0 0 0 -- stack-unit 0 -Current Settings(in block sizes) 1 block = 128 entries L2Acl : 6 Ipv4Acl : 4 Ipv6Acl : 0 Ipv4Qos : 2 L2Qos : 1 L2PT : 0 IpMacAcl : 0 VmanQos : 0 VmanDualQos : 0 EcfmAcl : 0 FcoeAcl : 0 iscsiOptAcl : 0 ipv4pbr : 0 vrfv4Acl : 0 Openflow : 0 fedgovacl : 0 nlbclusteracl: 0 -- stack-unit 1 -Current Settings(in block sizes) 1 block = 128
PAGE 590
test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax Parameters test cam-usage service-policy input input policy name stackunit {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters. number Enter all to get information for all the linecards/stack-units or enter the linecard/ stack-unit number to get information for a specific card. The range is 0-7 for all other S-Series.
PAGE 591
Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks. Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for linecards or stack units and port-pipes in the chassis. The port set value is from 0 to 0. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile.
PAGE 592
Example (SSeries) Term Explanation Estimated CAM per Port Estimates the amount of CAM space the listed policy will require. Status Indicates whether or not the policy will be allowed in the CAM.
PAGE 593
Control Plane Policing (CoPP) 14 The CoPP commands are supported on the Dell Networking platform. control-plane-cpuqos To manage control-plane traffic, enter control-plane mode and configure the switch. Syntax control-plane-cpuqos Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 594
Parameters policy-name Enter the service-policy name, using a string up to 32 characters. Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 595
Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 596
Command Modes Command History Usage Information CONFIGURATION Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv6 unknown-unicast Disable soft forwarding of unknown IPv6 destination packets.
PAGE 597
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 598
The following is a list of the Dell Networking OS version history for this command. Example 598 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 599
show ipv6 protocol-queue-mapping Display the queue mapping for each configured IPv6 protocol. Syntax show ipv6 protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.
PAGE 600
show mac protocol-queue-mapping Display the queue mapping for the MAC protocols. Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example 600 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.
PAGE 601
Data Center Bridging (DCB) 15 Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell Networking operating software commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 602
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default, iSCSI is enabled on the unit and the flow control is enabled on all of the interfaces. It is also acts as defaults when the link-level flow control is enabled on one or more interfaces.
PAGE 603
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. If you do not use the statistics parameter, both hardware and DCBx counters clear. description Enter a text description of the DCB policy (PFC input or ETS output). Syntax description text To remove the text description, use the no description command.
PAGE 604
Defaults PFC mode is on. Command Modes DCB INPUT POLICY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 605
Defaults No lossless queues are configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 606
port-setnumber Enter the port-set number. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 607
Usage Information Version Description 9.2.(0.0) Down status messages added. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. To clear the PFC TLV counters, use the clear pfc counters interface port-type slot/port[] command. The following describes the show interface pfc summary command shown in the following example. Field Description Interface Interface type with stack-unit and port number.
PAGE 608
Example (Summary) 608 Field Description PFC Link Delay Link delay (in quanta) used to pause specified priority traffic. Application Priority TLV: FCOE TLV Tx Status Status of FCoE advertisements in application priority TLVs from the local DCBX port: enabled or disabled. Application Priority TLV: SCSI TLV Tx Status Status of ISCSI advertisements in application priority TLVs from the local DCBX port: enabled or disabled.
PAGE 609
-------------------------------------FCOE TLV Tx Status is disabled ISCSI TLV Tx Status is disabled Local FCOE PriorityMap is 0x8 Local ISCSI PriorityMap is 0x10 Remote FCOE PriorityMap is 0x8 Remote ISCSI PriorityMap is 0x8 Dell# show interfaces tengigabitethernet 1/4 pfc detail Interface TenGigabitEthernet 1/4 Admin mode is on Admin is enabled Remote is enabled Remote Willing Status is enabled Local is enabled Oper status is recommended PFC DCBX Oper status is Up State Machine Type is Feature TLV Tx Statu
PAGE 610
Example (Summary) Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 611
Example (Summary) Dell(conf)# show stack-unit all stack-ports all pfc details stack unit 0 stack-port all Admin mode is On Admin is enabled, Priority list is 4-5 Local is enabled, Priority list is 4-5 Link Delay 45556 pause quantum 0 Pause Tx pkts, 0 Pause Rx pkts stack unit 1 stack-port all Admin mode is On Admin is enabled, Priority list is 4-5 Local is enabled, Priority list is 4-5 Link Delay 45556 pause quantum 0 Pause Tx pkts, 0 Pause Rx pkts ETS Commands The following ETS commands are supported on t
PAGE 612
Usage Information By default, equal bandwidth is assigned to each port queue and each dot1p priority in a priority group. To configure bandwidth amounts in associated dot1p queues, use the bandwidth-percentage command. When specified bandwidth is assigned to some port queues and not to others, the remaining bandwidth (100% minus assigned bandwidth amount) is equally distributed to unassigned non-strict priority queues in the priority group.
PAGE 613
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. dcb-enable Enable data center bridging. Syntax dcb enable[pfc-queues 1|4] To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 or 2.
PAGE 614
description Enter a text description of the DCB policy (PFC input or ETS output). Syntax description text To remove the text description, use the no description command. Parameters text Enter the description of the output policy. The maximum is 32 characters. Defaults none Command Modes • DCB INPUT POLICY • DCB OUTPUT POLICY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 615
Usage Information Version Description Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. By default: • All 802.1p priorities are grouped in priority group 0. • 100% of the port bandwidth is assigned to priority group 0. The complete bandwidth is equally assigned to each priority class so that each class has 12 to 13%.
PAGE 616
You can only associate output QoS policy profiles with the priority groups in the DCB output profile context; output QoS policy profiles are not permitted on output policy-maps. WRED, ECN, rate shaping, and rate limiting are not supported in output policies because DCBx does not negotiate these parameters with peer devices. You can apply a QoS output policy with WRED and/or rate shaping on a DCBx CIN-enabled interface.
PAGE 617
configured bandwidth allocation is ignored for priority-group traffic when you apply the output policy on an interface. If you enable this command for a QoS ETS output policy, no bandwidth percentage is assigned to the policy. Related Commands • qos-policy-output ets — configures the ETS bandwidth allocation. • bandwidth-percentage — bandwidth percentage allocated to priority traffic in port queues.
PAGE 618
TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is en
PAGE 619
Remote Parameters : ------------------Remote is disabled Local Parameters : -----------------Local is enabled TC-grp Priority# Bandwidth TSA -----------------------------------------------0 1 0,1,2 100% ETS 2 3 0 % SP 3 4,5,6,7 0 % SP 4 5 6 7 Oper status is init ETS DCBX Oper status is Down State Machine Type is Asymmetric Conf TLV Tx Status is enabled Reco TLV Tx Status is enabled 0 Input Conf TLV Pkts, 1955 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Reco TLV Pkts, 1955 Output Reco TLV Pkts, 0 Err
PAGE 620
1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# Bandwidth TSA 0 13% ETS 1 13% ETS 2 13% ETS 3 13% ETS 4 12% ETS 5 12% ETS 6 12% ETS 7 12% ETS Oper status is init Conf TLV Tx Status is disabled Traffic Class TLV Tx Status is disabled 0 Input Conf TLV Pkts, 0 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0T LIVnput Traffic Class TLV Pkts, 0 Output Traffic Class TLV Pkts, 0 Error Traffic Class Pkts Example (Detail) Dell(conf)# show interfaces tengigabitethernet 1/1 ets detail Interface
PAGE 621
2 3 4 5 6 7 0% 0% 0% 0% 0% 0% ETS ETS ETS ETS ETS ETS Priority# Bandwidth TSA 0 13% ETS 1 13% ETS 2 13% ETS 3 13% ETS 4 12% ETS 5 12% ETS 6 12% ETS 7 12% ETS Oper status is init Conf TLV Tx Status is disabled Traffic Class TLV Tx Status is disabled 0 Input Conf TLV Pkts, 0 Output Conf TLV Pkts, 0 Error Conf TLV Pkts 0 Input Traffic Class TLV Pkts, 0 Output Traffic Class TLV Pkts, 0 Error Traffic Class TLV Pkts show qos priority-groups Displays the ETS priority groups configured on the switch, including
PAGE 622
show stack-unit stack-ports ets details Displays the ETS configuration applied to egress traffic on stacked ports, including ETS Operational mode on each unit and the configurated priority groups with dot1p priorities, bandwidth allocation, and scheduler type. Syntax Parameters show stack-unit {all | stack-unit} stack-ports {all | portnumber} ets details stack-unit Enter the stack unit identification. port-number Enter the port number.
PAGE 623
-----------------------------------------------0 0,1,2,3,4,5,6,7 100% ETS 1 2 3 4 5 6 7 8 - DCBX Commands The following DCBX commands are supported on the Dell Networking OS. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements. Syntax advertise dcbx-app-tlv iscsi To disable DCBX iSCSI TLV advertisements, use the no advertise dcbx-apptlv iscsi command. Defaults Enabled Command Modes PROTOCOL LLDP Command History This guide is platform-specific.
PAGE 624
advertise dcbx-appln-tlv On a DCBX port with a manual role, configure the application priority TLVs advertised on the interface to DCBX peers. Syntax advertise dcbx-appln-tlv {fcoe | iscsi} To remove the application priority TLVs, use the no advertise dcbx-applntlv {fcoe | iscsi} command. Parameters {fcoe | iscsi} Enter the application priority TLVs, where: • fcoe: enables the advertisement of FCoE in application priority TLVs. • iscsi: enables the advertisement of iSCSI in application priority TLVs.
PAGE 625
Parameters {ets-conf | etsreco | pfc} Enter the PFC and ETS TLVs advertised, where: • ets-conf: enables the advertisement of ETS configuration TLVs. • ets-reco: enables the advertisement of ETS recommend TLVs. • pfc: enables the advertisement of PFC TLVs. Defaults All PFC and ETS TLVs are advertised. Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 626
Parameters config-source | autodownstream | auto-upstream | manual Enter the DCBX port role, where: • config-source: configures the port to serve as the configuration source on the switch. • auto-upstream: configures the port to receive a peer configuration. The configuration source is elected from auto-upstream ports. • auto-downstream: configures the port to accept the internally propagated DCB configuration from a configuration source.
PAGE 627
Parameters auto | cee | cin | ieee-v2.5 Enter the DCBX version type used on the interface, where: • auto: configures the port to operate using the DCBX version received from a peer. • cee: configures the port to use CDD (Intel 1.01). • cin: configures the port to use Cisco-Intel-Nuova (DCBX 1.0). • ieee-v2: configures the port to use IEEE 802.1az (Draft 2.5). Defaults Auto Command Modes INTERFACE PROTOCOL LLDP Command History This guide is platform-specific.
PAGE 628
Parameters {all | autodetect-timer | config-exchng | fail | mgmt | resource | sem | tlv} Enter the type of debugging, where: • all: enables all DCBX debugging operations. • auto-detect-timer: enables traces for DCBX autodetect timers. • config-exchng: enables traces for DCBX configuration exchanges. • fail: enables traces for DCBX failures. • mgmt: enables traces for DCBX management frames. • resource: enables traces for DCBX system resource frames.
PAGE 629
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module.
PAGE 630
show interface dcbx detail Displays the DCBX configuration on an interface. Syntax Parameters show interface port-type slot/port[] dcbx detail port-type Enter the port type. slot/port[] Enter the slot/port number. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 631
Field Description Local DCBX Compatibility mode DCBX version accepted in a DCB configuration as compatible. In auto-upstream mode, a port can only receive a DCBX version supported on the remote peer. Local DCBX Configured mode DCBX version configured on the port: CEE, CIN, IEEE v2.5, or Auto (port auto-configures to use the DCBX version received from a peer). Peer Operating version DCBX version that the peer uses to exchange DCB parameters.
PAGE 632
Example Field Description Total DCBX Frames transmitted Number of DCBX frames sent from the local port. Total DCBX Frames received Number of DCBX frames received from the remote peer port. Total DCBX Frame errors Number of DCBX frames with errors received. Total DCBX Frames unrecognized Number of unrecognizable DCBX frames received.
PAGE 633
dcb-map Create a DCB map to configure priority flow control (PFC) and enhanced transmission selection (ETS) on Ethernet ports that support converged Ethernet traffic. Apply the DCB map to an Ethernet interface. Syntax Parameters dcb-map map-name map-name Enter a DCB map name. The maximum number of alphanumeric characters is 32. Defaults None. There are no pre-configured PFC and ETS settings on S5000 Ethernet interfaces.
PAGE 634
priority-pgid Assign 802.1p priority traffic to a priority group in a DCB map. Syntax Parameters priority-pgid dot1p0_group-num dot1p1_group-num dot1p2_groupnum dot1p3_group-num dot1p4_group-num dot1p5_group-num dot1p6_group-num dot1p7_group-num dot1p0_groupnum Enter the priority group number for each 802.1p class of traffic in a DCB map.
PAGE 635
• Priority group 0 contains traffic with dot1p priorities 0, 1, and 2. • Priority group 1 contains traffic with dot1p priority 3. • Priority group 2 contains traffic with dot1p priority 4. • Priority group 4 contains traffic with dot1p priority 5, 6, and 7. To remove a priority-pgid configuration from a DCB map, enter the no priority-pgid command. pfc mode on Enable the PFC configuration on the port so that the priorities are included in DCBX negotiation with peer PFC devices.
PAGE 636
priority-group bandwidth pfc Configure the ETS bandwidth allocation and PFC mode used to manage port traffic in an 802.1p priority group. Parameters priority-group group-num Enter the keyword priority-group followed by the number of an 802.1p priority group. Use the prioritypgid command to create the priority groups in a DCB map. bandwidth percentage Enter the keyword bandwidth followed by a bandwidth percentage allocated to the priority group. The range of valid values is 1 to 100.
PAGE 637
If a priority group does not use its allocated bandwidth, the unused bandwidth is made available to other priority groups. To remove a priority-group configuration in a DCB map, enter the no prioritygroup bandwidth pfc command. By default, equal bandwidth is assigned to each dot1p priority in a priority group. Use the bandwidth parameter to configure the bandwidth percentage assigned to a priority group.
PAGE 638
show qos dcb-map Display the DCB parameters configured in a specified DCB map. Syntax Parameters Command Modes Command History Usage Information show qos dcb-map map-name map-name • • Displays the PFC and ETS parameters configured in the specified map. EXEC EXEC Privilege Version Description 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810 and S6000 platforms. 9.3(0.0) Introduced on the FC Flex IO module installed in the MXL 10/40GbE Switch.
PAGE 639
PG:0 TSA:ETS BW:50 PFC:OFF Priorities:0 1 2 4 5 6 7 PG:1 TSA:ETS Priorities:3 BW:50 PFC:ON dcb pfc-shared-buffer-size Configure the maximum amount of shared buffer size for PFC packets in kilobytes. You must configure the shared buffer size to be less than the total PFC buffer size.
PAGE 640
%ERROR: pfc shared buffer size configured cannot accommodate existing buffer requirement in the system. Example Dell(conf)#dcb pfc-shared-buffer-size 5000 dcb-buffer-threshold Configure the profile name for the DCB buffer threshold. This utility is supported on the S4810, S4820T, and S6000 platforms. Syntax Parameters dcb buffer—threshold profile-name profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
PAGE 641
buffer-size Ingress buffer size size Size of the ingress buffer in KB. Enter a number in the range of 0 to 7787. The default is 45 KB. pausethreshold Buffer limit for pause frames to be sent thresholdvalue Buffer limit at which the port sends the pause to peer in KB. Enter a number in the range of 0 to 7787. The default is 10 KB. resume-offset Buffer offset limit for resuming in KB thresholdvalue Buffer offset limit at which the port resumes the peer in KB.
PAGE 642
Example Dell(conf-dcb-buffer-thr)#priority 0 buffer-size 52 pausethreshold 16 resume-offset 10 shared-threshold-weight 7 qos-policy-buffer Create a QoS policy buffer and enter the configuration mode to configure the no-drop queues, ingress buffer size, buffer limit for pausing, and buffer offset limit for resuming. This utility is supported on the .
PAGE 643
sharedthresholdweight Buffer shared threshold weight size Weightage of the priorities on the shared buffer size in the system. Enter a number in the range of 0 to 9. The default shared threshold weight is 10. Default The default size of the ingress buffer is 45 KB. The default buffer limit at which the port sends the pause to peer and recommences the sending of packets to the peer is 10 KB. The default threshold weight of the shared buffer space is 10.
PAGE 644
dcb-policy buffer-threshold (Interface Configuration) Assign the DCB policy to the DCB buffer threshold profile on interfaces. This setting takes precedence over the global buffer-threshold setting. Syntax Parameters dcb-policy buffer-threshold profile-name bufferthreshold Configure the profile name for the DCB buffer threshold profile-name Enter the name of the profile, which can be a string of up to 32 characters in length.
PAGE 645
stack-port all Enter the port number of a port in a switch stack. Default None Command Modes CONFIGURATION mode Command History Version Description 9.3(0.0) Introduced on the S4810 and S4820T platforms. Usage Information You can configure up to a maximum of four lossless (PFC) queues. By configuring four lossless queues, you can configure four different priorities and assign a particular priority to each application that your network is used to process.
PAGE 646
Example Field Description Name Name of the DCB buffer threshold profile Buffer threshold parameters Buffer size allocated for the PFC priority queue and the priority of the queue Dell#show qos dcb buffer-threshold Name : test1 Buffer threshold parameters: pfc priority 0 buffer-size 40 pfc priority 3 buffer-size 50 show hardware stack-unit buffer-stats-snapshot (With Polling and History) View the buffer statistics tracking resource information with polling details and historical snapshots.
PAGE 647
• history Y Command Modes Port {id |all} prio-group {id | all} - ingress priority-group level snapshot Historical snapshot details of buffer space statistics, where Y can be one of the following: • Instance {all | id} - Displays the information for all instances or the specified instance of the snapshot. • Summary - Displays the consolidated information pertaining to the preceding three instances of the snapshot values collected in history.
PAGE 648
polled at 10, 20, 30, 40, and 50 seconds incrementally. If you attempt to enter the show command to display the fifth instance after 30 seconds of enabling polling, the aforementioned information message is shown. If specified instance ID is higher than the size of the maximum number of snapshot instances configured, the following error message is displayed on the console: %Error: Instance Id is not valid.
PAGE 649
-----------------------------------------------PG# Instance 1 Instance 2 Instance 3 Instance 4 Instance 5 Shared Hdrm Shared Hdrm Shared Hdrm Shared Hdrm Shared Hdrm [in CELLS] -------------------------------------------------------------------------------------------------------------6 9 2 0 0 1 0 4 1 7 1 7 0 0 0 0 0 0 0 0 0 1 In the following example, the Headroom Cells field indicates the amount of shared buffer area that is allocated to store packets that are received after the pause frame is
PAGE 650
MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 Stack-unit: 0 unit: 0 port: 5 (interface Fo 0/4) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 1 0 0 2 0 0 3 0 0 4 0 0 5 0 0 6 0 0 7 0 0 --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 UCAST
PAGE 651
UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 0 1 2 3 4 5 6 7 8 9 10 11 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 To determine the port that is congested and monitor all queues (including multicast and unicast queues] only on that port: Dell#$show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 queue all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) -------------------------------------
PAGE 652
MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST Dell# 0 1 2 3 4 5 6 7 8 0 0 0 0 0 0 0 0 0 To determine the port that is congested and monitor all the unicast Queues on that port: Dell#show hardware stack-unit 0 buffer-stats-snapshot unit 0 resource port 1 queue ucast all Stack-unit: 0 unit: 0 port: 1 (interface Fo 0/0) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------UCAST 0 0 UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAS
PAGE 653
--------------------------------------6 0 0 Dell#show hardware stack-unit 1 buffer-stats-snapshot unit 0 resource port 1 prio 6 Stack-unit: 1 unit: 0 port: 1 (interface Te 1/50) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------6 0 0 Dell#show hardware stack-unit 1 buffer-stats-snapshot unit 0 resource port 1 prio 6 Stack-unit: 1 unit: 0 port: 1 (interface Fo 1/1) --------------------------------------PG# SHARED CELLS HEADROOM CELLS -----------------
PAGE 654
buffering is enabled, the limit per port for queues depends on the availability of the buffer. Example Dell(conf)#dcb pfc-total-buffer-size 5000 Dell(conf)#dcb pfc-total-buffer-size 4000 %ERROR: Total pfc buffer size configured cannot accommodate existing buffer requirement in the system. show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration.
PAGE 655
pfc priority 0 buffer-size 80 pause-threshold 60 resumethreshold 30 On interface on which PFC is enabled: Show interface tengigabitethernet 1/1 pfc buffer-threshold -------------------------------------------------------------------------------------------Queue# Lossless Buffer-size Pause-threshold Resumeoffset Shared threshold (KB) (KB) (KB) weight -------------------------------------------------------------------------------------------0 No 1 No 2 Yes 20 9 3 Yes 52 25 15 0 4 Yes 45 25 5 5 No 6 No 7 No De
PAGE 656
dcb pfc-queues Configure the number of PFC queues. This utility is supported on the and platforms. Syntax Parameters dcb pfc-queues value value Enter the number of PFC queues in the range of 0 through 4. The number of ports supported based on lossless queues configured will depend on the buffer. Default The default number of PFC queues in the system is 2 for S4810 and 1 for S6000 platforms. Command Modes CONFIGURATION mode Command History Version Description 9.7(0.0) Introduced on the S6000-ON.
PAGE 657
Command History Usage Information Limitations Version Description 9.7(0.0) Introduced on the S6000-ON. 9.3 (0.1) Introduced on S6000, S4810, and S4820T. PFC and ETS are enabled by default on the interfaces when DCB is globally enabled (refer to dcb enable). In some network topology, you may want to disable PFC on an interface and apply link level flow control; Similarly you may want to disable ETS on an interface and apply QoS bandwidth configurations.
PAGE 658
Dynamic Host Configuration Protocol (DHCP) 16 Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. The Dell Networking operating system supports the basic DHCP commands on the platform.
PAGE 659
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 660
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. default-router Assign a default gateway to clients based on the address pool. Syntax Parameters default-router address [address2...address8] address Enter a list of routers that may be the default gateway for clients on the subnet. You may specify up to eight routers. List them in order of preference. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 661
Command Modes CONFIGURATION DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 662
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. domain-name Assign a domain to clients based on the address pool. Syntax Parameters domain-name name name Give a name to the group of addresses in a pool. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 663
Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 664
Version Description 8.2.1.0 Introduced on the C-Series and S-Series. host For manual (rather than automatic) configurations, assign a host to a single-address pool. Syntax Parameters host address address/mask Enter the host IP address and subnet mask. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 665
infinite Specify that the lease never expires. Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 666
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell Networking recommends specifying clients as hybrid. Syntax Parameters netbios-node-type type type Enter the NETBIOS node type: • Broadcast: Enter the keyword b-node. • Hybrid: Enter the keyword h-node. • Mixed: Enter the keyword m-node.
PAGE 667
network Specify the range of addresses in an address pool. Syntax Parameters network network /prefix-length network/ prefix-length Specify a range of addresses. Prefix-length range is from 17 to 31. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 668
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp binding Display the DHCP binding table. Syntax show ip dhcp binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 669
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 670
Version Description 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp server Display the DHCP server statistics. Syntax show ip dhcp server statistics Defaults none Command Modes EXEC Privilege Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 671
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series. arp inspection-trust — specifies a port as trusted so that ARP frames are not validated against the binding table.
PAGE 672
clear ip dhcp snooping Clear the DHCP binding table. Syntax Parameters clear ip dhcp snooping {binding | source-address-validation discard-counters [interface interface]} binding Clears the binding table. sourceaddressvalidation discardcounters Clears discard counters from all the interfaces configured with IP Source Guard. interface interface (OPTIONAL) Specifies an interface to clear the discard counters.
PAGE 673
Example Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 674
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 675
ip dhcp snooping binding Create a static entry in the DHCP binding table. Syntax Parameters [no] ip dhcp snooping binding mac address vlan-id vlan-id ip ip-address interface type slot/port lease number mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 676
Related Commands Version Description 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp snooping database Delay writing the binding table for a specified time. Syntax Parameters ip dhcp snooping database write-delay minutes minutes The range is from 5 to 21600. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 677
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 678
Version Description 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable the IP Source Guard. Syntax Parameters [no] ip dhcp source-address-validation [ipmac] [vlan vlan-id] ipmac Enable IP+MAC Source Address Validation. vlan vlan-id (OPTIONAL) SAV validates the source IP address along with the source VLAN ID against the DHCP snooping binding table.
PAGE 679
3. Reload the system. ip dhcp relay information-option Enable Option 82. Syntax Parameters ip dhcp relay information-option [trust-downstream] [vpn] trustdownstream Configure the system to trust Option 82 when it is received from the previous-hop router. vpn Enter the keyword vpn to add VPN/VRF related sub-option to relay agent information Option 82. NOTE: Adds the VPN/VRF related sub-options into the relay agent information option(82).
PAGE 680
ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 681
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4. (0.0) Introduced on the S-Series and Z-Series. Usage Information Use this command on the interfaces where the DHCP clients are connected to forward the packets from clients to DHCP server and vice-versa.
PAGE 682
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version 9.6(0.0) Added the discard-counters, interface keywords, and the interface variable. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.
PAGE 683
packets) permit vlan 10 host 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) permit vlan 10 host 1.1.1.3 host 00:00:00:00:01:03 count (0 packets) ipmac-vlan sav access-list on Port-channel 10 on stack-unit 2 Total cam count 5 permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 1.1.1.1 host 00:00:00:00:01:01 count (0 packets) permit vlan 10 host 1.1.1.2 host 00:00:00:00:01:02 count (0 packets) permit vlan 10 host 1.1.1.
PAGE 684
Commands to Configure DNS To configure the Domain Names Systems (DNS) on the system, use the following commands: ip name-server Configures the name server IP addresses for VRF. Using this command, you can configure up to a maximum of six IP addresses per VRF. Syntax ip name-server [vrf vrf-name] ip-address [ip-address2] [ipaddress3] [ip-address4] [ip-address5] [ip-address6] To undo the name server ip address configuration for VRF, use the no ip nameserver [vrf vrf-name] ip-address command.
PAGE 685
ip domain-name Configures the default domain corresponding to a specific VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. Syntax ip domain-name [vrf vrf-name] name To undo the domain name configuration corresponding to a specific VRF, use the no ip domain-name [vrf vrf-name] name command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the domain corresponding to that VRF.
PAGE 686
Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to add a domain name to the DNS list corresponding to that VRF. name Enter the name of the domain to be appended to the DNS list corresponding to the VRF. Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 687
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 688
Usage Information Use this command to delete one or all dynamically learned host table entries corresponding to a specific VRF.
PAGE 689
Equal Cost Multi-Path (ECMP) 17 Equal cost multi-path (ECMP) is supported on the Dell Networking OS. ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold. Syntax ecmp-group {ecmp-group-id interface interface | link-bundlemonitor} To remove the selected interface, use the ecmp-group no interface command.
PAGE 690
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID. You can then assign interfaces to the ECMP group using CONFIGURATION ECMP-GROUP mode. You can also enable on the port-channel configuration using the CONFIGURATION ECMP-GROUP command mode.
PAGE 691
ecmp crc16 | crc16cc | crc32MSB | crc32LSB | crcupper | dest-ip | lsb | xor1 | xor2 | xor4 | xor8 | xor16 hg {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} stack-unit stack-unitnumber | portset port-pipe TeraScale and ExaScale Only: Enter the keyword ecmp then one of the following options: • crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc: Use CRC16_CCITT — 16 bit CRC16 using CRC16-CCITT polynomial • crc32MSB: Use CRC32_UPPER — MSB 16 bits of
PAGE 692
Enter the keywords port-set port-pipe then the port pipe number. The range is from 0 to 5. hg-seed seedvalue stackunit Z-Series only: Enter the keywords hg-seed then the hash algorithm seed value. The range is from 0 to 2147483646. Enter the keywords stack-unit then the stack unit number. Enter the keywords port-set then the stack-unit port-pipe number. lag hash algorithm Z-Series only: Enter the keywords hg-seed . The range is from 0 to 47.
PAGE 693
Usage Information Version Description 7.7.1.1 Added the nh-ecmp option. To ensure that CRC is not used for LAG, set the default hash-algorithm method on ExaScale systems. For example,hash-algorithm ecmp xor lag checksum nh-ecmp checksum. The hash value calculated with the hash-algorithm command is unique to the entire chassis. The hash algorithm command with the stack—unit option changes the hash for a particular stack—unit by applying the mask specified in the IPSA and IPDA fields.
PAGE 694
hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group. Term heading Description heading Syntax hash-algorithm ecmp {crc-upper} | {dest-ip} | {lsb} To return to the default hash algorithm, use the no hash-algorithm ecmp command. Parameters Defaults crc-upper Uses the upper 32 bits of the key for the hash computation. The default is crc-lower. dest-ip Uses the destination IP for ECMP hashing. The default is enabled.
PAGE 695
Term heading Description heading various test scenarios, but if the default algorithm does not provide satisfactory distribution of traffic, use this command to designate another algorithm. When a member leaves or is added to the ECMP group, the hash algorithm is recalculated to balance traffic across the members. hash-algorithm seed Select the seed value for the ECMP, LAG, and NH hashing algorithm.
PAGE 696
FTOS provides a CLI-based solution for modifying the hash seed to ensure that on each configured system, the ECMP selection is same. When configured, the same seed is set for ECMP, LAG, and NH, and is used for incoming traffic only. NOTE: While the seed is stored separately on each port-pipe, the same seed is used across all CAMs. You cannot separate LAG and ECMP but you can use different algorithms across the chassis with the same seed.
PAGE 697
Usage Information You must save the new ECMP settings to the startup-config (write-mem) then reload the system for the new settings to take effect. Related Commands show ip cam stack-unit – Display content-addressable memory (CAM) entries for an S-Series switch. ip ecmp weighted Enables weighted ECMP calculations. Syntax ip ecmp weighted To disable weighted ECMP calculations, enter the no ip ecmp weighted command.
PAGE 698
Command Modes Command History • ECMP-GROUP • PORT-CHANNEL INTERFACE This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810.
PAGE 699
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. show config Display the ECMP configuration. Syntax show config Command Modes CONFIGURATION-ECMP-GROUP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 700
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 701
FIPS Cryptography 18 To configure federal information processing standards (FIPS) cryptography, use the following commands: fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command.
PAGE 702
show fips status Displays the status of the FIPS mode. Syntax show fips status Defaults None Command Modes EXEC Example Dell#show fips status FIPS Mode : Disabled Dell# Dell#show fips status FIPS Mode : Enabled Dell# Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.1(0.
PAGE 703
Version 8.3.12.0 Example Introduced on S4810. Dell#show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192cbc,aes256-cbc,aes128-ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-sha1-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled.
PAGE 704
ssh Open an SSH connection specifying the hostname, username, port number, and version of the SSH client. Syntax Parameters ssh {hostname|ipv4 address|ipv6 address} [-c encryption cipher|-l username|-m HMAC alogorithm|-p port-number|-v {1|2}] hostname (OPTIONAL) Enter the IP address or the hostname of the remote device. ipv4 address (OPTIONAL) Enter the IP address in dotted decimal format A.B.C.D.
PAGE 705
• hmac-shal-96: Force ssh to use the hmac-sha1–96 HMAC algorithm. • hmac-md5: Force ssh to use the hmac-md5 HMAC algorithm. • hmac-md5–96: Force ssh to use the hmac-md5–96 HMAC algorithm. With the FIPS mode enabled: • hmac-md5: Force ssh to use the hmac-md5 HMAC algorithm. • hmac-md5–96: Force ssh to use the hmac-md5–96 HMAC algorithm. • hmac-sha1: Force ssh to use the hmac-sha1 HMAC algorithm. • hmac-shal-96: Force ssh to use the hmac-sha1–96 HMAC algorithm.
PAGE 706
Related Commands Usage Information ip ssh server Configure an SSH server. show ip ssh client-pubkeys Display the client-public keys. Dell Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative.
PAGE 707
aes192-ctr Force ssh aes256-ctr Force ssh Dell#ssh 10.10.10.
PAGE 708
19 FCoE Transit To enable the FCoE Transit feature and configure FIP snooping, use the following Dell Networking Operating System commands on the platform. In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs).
PAGE 709
Version Description 8.3.12.0 Introduced on the S4810. clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface. Syntax Parameters clear fip-snooping statistics [interface vlan vlan-id | interface fortyGigEport-type port/slot | interface port-channel port-channel-number] vlan-id Enter the VLAN ID of the FIP packet statistics to be cleared.
PAGE 710
debug fip snooping Enable debugging on FIP snooping. Syntax Parameters debug fip-snooping [all | acl | error | ifm | info | ipc | tx] all Enter the keyword all to enable debugging on all the options. acl Enter the keyword acl for ACL-specific debugging. error Enter the keyword error for error-specific debugging. ifm Enter the keyword ifm for IFM-specific debugging. info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging.
PAGE 711
interface • all — Enter the keyword all to enable debugging on all the options. • discovery — Enter the keyword discovery to enable debugging on FCF advertisements and ENode solicitation. • virtual-link-instantiation — Enter the keywords virtual-link-instantiation to enable debugging on FLOGI, FDISC, and FLOGO packets. • virtual-link-maintenance — Enter the keywords virtual-link-maintenance to enable debugging on FIP clear virtual link frames and keepalives.
PAGE 712
To disable the FCoE transit feature, use the no feature fip-snooping command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T.
PAGE 713
Usage Information The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. The maximum number of FIP snooping sessions supported per ENode server is 16. fip-snooping fc-map Configure the FC-MAP value FIP snooping uses on all VLANs. Syntax fip-snooping fc-map fc-map-value To return the configured FM-MAP value to the default value, use the no fipsnooping fc-map command. Parameters fc-map-value Enter the FC-MAP value FIP snooping uses. The range is from 0EFC00 to 0EFCFF.
PAGE 714
To remove the configured number of supported sessions, use the no fipsnooping max—sessions-per-enodemac command. Parameters max-value Defaults 32 Command Modes • Command History Usage Information Enter the maximum number of FIP snooping sessions with an ENode that are supported on the switch. The range is 1 to 64. CONFIGURATION Version 9.0(1.3) Introduced on the S5000.
PAGE 715
Usage Information Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The maximum number of FCFs supported per FIP snooping-enabled VLAN is four. fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links. Syntax fip-snooping port-mode fcoe-trusted To remove the bridge-to-bridge link configuration from the port, use the no fipsnooping port-mode fcoe-trusted command.
PAGE 716
show fip-snooping config Display the FIP snooping status and configured FC-MAP values. Syntax show fip-snooping config Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.
PAGE 717
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 718
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 719
Parameters vlan-id Enter the vlan-id of the specified VLAN to display. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example FCoE Transit Version Description 9.7(0.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 720
show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax Parameters show fip-snooping statistics [interface vlan vlan-id | interface port-type port/slot | interface port-channel portchannel-number] vlan-id Enter the VLAN ID of the FIP packet statistics displays. port-type port/ slot Enter the port-type and slot number of the FIP packet statistics displays.
PAGE 721
FCoE Transit Field Description Number of FLOGI Number of FIP-snoop FLOGI request frames received on the interface. Number of FDISC Number of FIP-snoop FDISC request frames received on the interface. Number of FLOGO Number of FIP-snoop FLOGO frames received on the interface Number of ENode Keep Alives Number of FIP-snoop ENode keep-alive frames received on the interface.
PAGE 722
Field Description due to Hardware Config Example Dell# show fip-snooping statistics interface vlan 100 Number of Vlan Requests :0 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :2 Number of Unicast Discovery Solicits :0 Number of FLOGI :2 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :9021 Number of VN Port Keep Alive :3349 Number of Multicast Discovery Advertisement :4437 Number of Unicast Discovery Advertisement :2 Number of FLOGI Accepts :2 Number of FLOGI R
PAGE 723
Number Number Number Number Number Number Number Number Number Number Number Number of of of of of of of of of of of of Multicast Discovery Advertisement :4451 Unicast Discovery Advertisement :2 FLOGI Accepts :2 FLOGI Rejects :0 FDISC Accepts :16 FDISC Rejects :0 FLOGO Accepts :0 FLOGO Rejects :0 CVL :0 FCF Discovery Timeouts :0 VN Port Session Timeouts :0 Session failures due to Hardware Config :0 show fip-snooping system Display information on the status of FIP snooping on the switch (enabled or disabl
PAGE 724
show fip-snooping vlan Display information on the FCoE VLANs on which FIP snooping is enabled. Syntax show fip-snooping vlan Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.
PAGE 725
FCoE Transit Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 726
20 Force10 Resilient Ring Protocol (FRRP) Force10 resilient ring protocol (FRRP) is supported on Dell Networking OS. FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a highspeed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode.
PAGE 727
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series.
PAGE 728
Parameters event Enter the keyword event to display debug information related to ring protocol transitions. packet Enter the keyword packet to display brief debug information related to control packets. detail Enter the keyword detail to display detailed debug information related to the entire ring protocol packets. ring-id (Optional) Enter the ring identification number. The range is from 1 to 255. count number Enter the keyword count then the number of debug outputs.
PAGE 729
Parameters Word Enter a description of the ring. Maximum: 255 characters. Defaults none Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 730
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. interface Configure the primary, secondary, and control-vlan interfaces. S5000 Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 731
Defaults none Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 732
Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.
PAGE 733
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. protocol frrp Enter the Resilient Ring Protocol and designate a ring identification. Syntax protocol frrp {ring-id} To exit the ring protocol, use the no protocol frrp {ring-id} command. Parameters ring-id Enter the ring identification number. The range is from 1 to 255.
PAGE 734
Usage Information This command places you into the resilient ring protocol. After executing this command, the command line prompt changes to conf-frrp. show frrp Display the resilient ring protocol configuration. Syntax Parameters show frrp [ring-id [summary]] | [summary] ring-id Enter the ring identification number. The range is from 1 to 255 summary (OPTIONAL) Enter the keyword summary to view just a summarized version of the Ring configuration.
PAGE 735
Usage Information Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell Networking OS requires a command line confirmation before the command is executed.
PAGE 736
To remove the timer, use the no timer {hello-interval [milliseconds]}| {dead-interval milliseconds} command. Parameters hello-interval milliseconds Enter the keyword hello-interval then the time, in milliseconds, to set the hello interval of the control packets. The milliseconds must be entered in increments of 50 millisecond; for example, 50, 100, 150, and so on. If an invalid value is entered, an error message is generated. The range is from 50 to 2000 ms. Default: 500 ms.
PAGE 737
GARP VLAN Registration (GVRP) 21 The Dell Networking operating system supports the basic GVRP commands on the Dell Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 738
• VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all dynamic VLANs are removed. • GVRP manages the active topology, not non-topological data such as VLAN protocols. If a local bridge must classify and analyze packets by VLAN protocols, manually configure protocol-based VLANs, and simply rely on GVRP for VLAN updates.
PAGE 739
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series show gvrp statistics — displays the GVRP statistics. debug gvrp Enable debugging on GVRP. S5000 Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration.
PAGE 740
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series disable Globally disable GVRP. Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific.
PAGE 741
garp timers Set the intervals (in milliseconds) for sending GARP messages. Syntax garp timers {join | leave | leave-all} To return to the previous setting, use the no garp timers {join | leave | leave-all} command. Parameters join Enter the keyword join then the number of milliseconds to configure the join time. The range is from 100 to 147483647 milliseconds. The default is 200 milliseconds. NOTE: Designate the milliseconds in multiples of 100.
PAGE 742
Usage Information Related Commands • Join Timer — Join messages announce the willingness to register some attributes with other participants. For reliability, each GARP application entity sends a Join message twice and uses a join timer to set the sending interval. • Leave Timer — Leave announces the willingness to de-register with other participants. Together with Join, Leave messages help GARP participants complete attribute reregistration and de-registration.
PAGE 743
Related Commands disable — globally disables GVRP. gvrp registration Configure the GVRP register type. Syntax gvrp registration {fixed | normal | forbidden} To return to the default, use the gvrp register normal command. Parameters fixed Enter the keyword fixed then the VLAN range in a commaseparated VLAN ID set. normal Enter the keyword normal then the VLAN range in a comma-separated VLAN ID set. This setting is the default.
PAGE 744
about the VLAN through GVRP. If the VLAN is removed from the port that sends GVRP advertisements to this device, the port stops being a member of the VLAN. To advertise or learn about VLANs through GVRP, use the forbidden command when you do not want the interface. Related Commands show gvrp — displays the GVRP configuration including the registration. protocol gvrp Access GVRP protocol — (config-gvrp)#. Syntax protocol gvrp Defaults Disabled.
PAGE 745
show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 746
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 747
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 748
summary • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. Enter the keyword summary to display just a summary of the GVRP statistics. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 749
Join In Transmitted: 0 Empty Transmitted: 0 Leave In Transmitted: 0 Leave Empty Transmitted: 0 Leave All Transmitted: 41 Invalid Messages/Attributes skipped: 0 Failed Registrations: 0 Dell# Related Commands show gvrp — displays the GVRP configuration.
PAGE 750
High Availability (HA) 22 High availability (HA) in the Dell Networking operating software is configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. The feature is available on Dell Networking OS. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol.
PAGE 751
patchversion.rtp). For example, a patch labeled “7.8.1.0-EH-rp2-l2mgr-1.rtp” identifies that this patch applies to Dell Networking OS version 7.8.1.0 — E-Series platform, for RP2, addressing the layer 2 management process, and this patch is the first version of this patch. There is no need to reload or reboot the system when you insert the patch. The InService Modular patch replaces the existing process code. After installation is complete, the system executes the patch code as though it was always there.
PAGE 752
Related Commands show processes restartable redundancy auto-failover-limit Specify an auto-failover limit for RPMs. When a non-recoverable fatal error is detected, an automatic RPM failover occurs. This command does not affect user-initiated (manual) failovers. Syntax redundancy auto-failover-limit [count number [period minutes] | period minutes]] To disable the auto-failover limit control, use the no redundancy autofailover-limit command.
PAGE 753
Usage Information If you disable auto failover, enter the redundancy auto-failover-limit (without any parameters) to set auto failover to the default parameters (Count 3, Period 60 minutes). To view the redundancy status, use the show redundancy command. When you change one or both of the optional parameters, Dell Networking OS checks that the interval between auto failovers is more than five (5) minutes. If the interval is less, Dell Networking OS returns a configuration error message.
PAGE 754
Parameters stack-unit Enter the keyword stack-unit then the stack-unit ID number. Default Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 755
Default The RPM in slot R0 is the Primary RPM. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series.
PAGE 756
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the E-Series. • show lacp — displays the lacp configuration. • show redundancy — displays the current redundancy configuration. redundancy reset-counter Reset failover counter and timestamp information displayed in the show redundancy command.
PAGE 757
redundancy sfm standby Place the SFM in an offline state. Syntax redundancy sfm standby To place the SFM in an online state, use the no redundancy sfm standby command. Default The SFM is online by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 758
----------------------------------------0 active 1 standby Dell(conf)#no redundancy sfm Taking secondary SFM online... ! 10Dell(conf)#do show sfm all Switch Fabric State: up -- Switch Fabric Modules -Slot Status ------------------------------------------0 active 1 active redundancy synchronize Manually synchronize data once between the Master and Stand-by stack units. Syntax Parameters redundancy synchronize [full] full Enter the keyword full to synchronize all data. Default Not configured.
PAGE 759
show patch Display the system patches loaded with the In-Service Modular Hot Fix command. Syntax show patch Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.2.1.
PAGE 760
Version Description 8.4.1.0 Introduced on the E-Series.
PAGE 761
Usage Information Version Description 7.6.1.0 Introduced on the E-Series. The following describes the show redundancy command shown in the following example. Field Description RPM Status Displays the following information: • Slot number of the RPM. • Whether the RPM is Primary or Standby. • The state of the RPM: Active, Standby, Booting, or Offline. • Whether the link to the second RPM is up or down.
PAGE 762
Field Description • Running Config is the current running-config. This field only appears when you enter the command from the Primary RPM. Example Dell#show redundancy -- RPM Status ------------------------------------------------RPM Slot ID: 1 RPM Redundancy Role: Primary RPM State: Active RPM SW Version: 7.5.1.0 Link to Peer: Up -- PEER RPM Status ------------------------------------------------RPM State: Standby RPM SW Version: 7.5.1.
PAGE 763
Internet Group Management Protocol (IGMP) 23 The IGMP commands are supported by the Dell Networking operating software on the Dell Networking OS. This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376.
PAGE 764
NOTE: Applies to specific VRF if input is provided, else applies to default VRF. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format. interface interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 765
clear ip igmp snooping groups Clear snooping entries from the group cache table. S5000 Syntax Parameters clear ip igmp snooping groups [group-address interface | interface] group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format. interface interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 766
• Parameters To disable all debugging, use the undebug all command. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging of IGMP packets corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 767
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. S5000 Syntax Parameters debug ip igmp snooping [group address | interface] • To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. • To disable all debugging, use the undebug all command. snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 768
ip igmp access-group To specify access control for packets, use this feature. Syntax ip igmp access-group access-list To remove the feature, use the no ip igmp access-group access-list command. Parameters access-list Enter the name of the extended ACL (16 characters maximum). Defaults Not configured Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 769
To disable ip igmp immediate leave, use the no ip igmp immediateleave command. Parameters group-list prefix-listname Enter the keywords group-list then a string up to 16 characters long of the prefix-list-name. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 770
ip igmp last-member-query-interval Change the last member query interval, which is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages. This interval is also the interval between GroupSpecific Query messages. S5000 Syntax ip igmp last-member-query-interval milliseconds To return to the default value, use the no ip igmp last-member-queryinterval command. Parameters milliseconds Enter the number of milliseconds as the interval.
PAGE 771
ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. S5000 Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 772
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 773
Version Description 7.5.1.0 Introduced on the C-Series in Interface VLAN mode only to enable the system to act as an IGMP Proxy Querier. E-Series legacy command. ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list.
PAGE 774
Version Description Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.7.1.0 Introduced on the E-Series. Usage Information Mapping applies to both v1 and v2 IGMP joins; any updates to the ACL are reflected in the IGMP groups. You may not use extended access lists with this command. When you configure a static SSM map and the router cannot find any matching access lists, the router continues to accept (*,G) groups.
PAGE 775
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. show ip igmp groups View the IGMP groups. S5000 Syntax Parameters show ip igmp [vrf vrf-name] groups [group-address [detail] | detail | interface [group-address [detail]]] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 776
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series and C-Series. 7.5.1.0 Expanded to support the detail option. E-Series legacy command.
PAGE 777
Example (VLT) NOTE: The asterisk (*) after the port channel number (Po 2) highlighted in the following example indicates the port channel is VLT, that the local VLT port channel is down and the remote VLT port is up. Dell#show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Mode Uptime Expires Last Reporter 225.0.0.0 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 Example (Details) 225.0.0.1 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 225.0.0.
PAGE 778
• For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF.
PAGE 779
IGMP querying router is 35.0.0.1 (this system) IGMP version is 2 show ip igmp ssm-map Display is a list of groups that are currently in the IGMP group table and contain SSM mapped sources. S5000 Syntax Parameters show ip igmp [vrf vrf-name] ssm-map [group] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 780
Group source list Source address 65.0.0.1 65.0.0.2 65.0.0.3 65.0.0.4 65.0.0.5 Related Commands Expires 00:01:22 00:01:22 00:01:22 00:01:22 00:01:22 ip igmp ssm-map — uses a statically configured list to translate (*,G) memberships to (S,G) memberships. IGMP Snooping Commands Dell Networking OS supports IGMP Snooping version 2 and 3 on all Dell Networking systems. Important Points to Remember for IGMP Snooping • Dell Networking OS supports version 1, version 2, and version 3 hosts.
PAGE 781
If the IP SA of the incoming IGMP general query is higher than the VLAN IP address, the switch continues to work as an IGMP snooping Querier. ip igmp snooping enable Enable IGMP snooping on all or a single VLAN. This command is the master on/off switch to enable IGMP snooping. Syntax ip igmp snooping enable To disable IGMP snooping, use the no ip igmp snooping enable command. Defaults Disabled. Command Modes • CONFIGURATION • INTERFACE VLAN Command History This guide is platform-specific.
PAGE 782
ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. S5000 Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 783
ip igmp snooping flood This command controls the flooding behavior of unregistered multicast data packets. Syntax ip igmp snooping flood To undo this configuration, use the no ip igmp snooping flood command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 784
To return to the default value, use the no ip igmp snooping last-memberquery-interval command. Parameters milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds. Defaults 1000 milliseconds Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 785
To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number.
PAGE 786
ip igmp snooping querier Enable IGMP querier processing for the VLAN interface. S5000 Syntax ip igmp snooping querier To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 787
show ip igmp snooping groups Display snooping related information for all the IGMP groups, interface or one group of one interface. S5000 Syntax Parameters show ip igmp snooping groups [group-address [detail] | detail | interface [group-address [detail]]] snooping Enter the keyword snooping to display snooping related information. group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only.
PAGE 788
Example Field Description Group Address Lists the multicast address for the IGMP group. Interface Lists the interface type, slot and port number. Mode Displays the IGMP version used. Uptime Displays the amount of time the group has been operational. Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. Member Ports Indicates the port channel.
PAGE 789
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
PAGE 790
24 Interfaces The commands in this chapter are supported by Dell Networking operating software on the S5000 platform. This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands • Time Domain Reflectometer (TDR) • UDP Broadcast Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 791
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a tunnel interface, enter the keyword tunnel. The range is from 1 to 16383. vrrp [[ipv6] vrid] (OPTIONAL) Enter the keyword vrrp to clear the counters of all VRRP groups. To clear the counters of VRRP groups on all IPv6 interfaces, enter ipv6.
PAGE 792
Version Description 6.5.1.0 Updated the definition of the learning-limit option for clarity. Example Dell#clear counters Clear counters on all interfaces [confirm] Related Commands mac learning-limit — allows aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. show interfaces — displays information on the interfaces. clear dampening Clear the dampening counters on all the interfaces or just the specified interface.
PAGE 793
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 794
Usage Information This command only works on ports that the system recognizes as CX4 ports. The show interfaces command shown in the Example below describes an attempt to configure an XFP port in an S25P with the command after inserting a CX4 converter into the port. NOTE: When using a long CX4 cable between the C-Series and the S-Series, to avoid errors, configure the cable using the cx4-cable-length short command only. NOTE: The 15M CX4 active cable is not supported on the C-Series and Sseries.
PAGE 795
period expires. The range is from 1 to 30 seconds. The default is 5 seconds. reusethreshold Enter a number as the reuse threshold, the penalty value below which the interface state is changed to “up”. The range is from 1 to 20000. The default is 750. suppressthreshold Enter a number as the suppress threshold, the penalty value above which the interface state is changed to “error disabled”. The range is from 1 to 20000. The default is 2500.
PAGE 796
Example Dell(conf-if-te-1/10)#dampening 20 800 4500 120 Dell(conf-if-te-1/10)# Related Commands clear dampening — clears the dampening counters on all the interfaces or just the specified interface. show interfaces dampening — displays interface dampening information. description Assign a descriptive text string to the interface. Syntax description desc_text To delete a description, use the no description command. Parameters desc_text Enter a text string up to 240 characters long.
PAGE 797
Usage Information Important Points to Remember: • To use special characters as a part of the description string, you must enclose the whole string in double quotes. • Spaces between characters are not preserved after entering this command unless you enclose the entire description in quotation marks (“desc_text”). • Entering a text string after the description command overwrites any previous text string that you previously configured as the description.
PAGE 798
Version Description Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Introduced Usage Information This command applies to any physical interface with speed set to 10/100. Related Commands negotiation auto — enables or disables auto-negotiation on an interface. NOTE: Starting with Dell Networking OS version 7.8.1.
PAGE 799
Related Commands interface ManagementEthernet — configures the Management port on the system (either the primary or standby stack-unit). flowcontrol Control how the system responds to and generates 802.3x pause frames on 10 Gig ports. Syntax Parameters flowcontrol rx {off | on} tx {off | on} rx on Enter the keywords rx on to process the received flow control frames on this port. This is the default value for the receive side.
PAGE 800
Usage Information The globally assigned 48-bit Multicast address 01-80-C2-00-00-01 is used to send and receive pause frames. To allow full-duplex flow control, stations implementing the pause operation instruct the MAC to enable the reception of frames with a destination address equal to this multicast address. When a port receives traffic at a higher rate than it can process, the frames are stored in the port buffer. As a result, buffer usage increases.
PAGE 801
Example (Values) This Example shows how Dell Networking OS negotiates the flow control values between two Dell Networking chassis connected back-to-back using 1G copper ports.
PAGE 802
interface Configure a physical interface on the switch. Syntax Parameters interface interface range interface range Enter one of the following keywords and slot/port or number information: • For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to1. The port range is 0.
PAGE 803
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport.
PAGE 804
interface group Create or delete group of VLANs with a single command. You can also use this command to apply a set of configurations on a group of interfaces. Syntax interface group [fortyGigE slot/port { - port }| tengigabitethernet slot/port { - port } | vlan vlanid {vlanid } ] To delete a range of VLANs, use the following command: no interface group vlan vlanid {- vlanid} Parameters interface, interface,... Enter the keywords interface group and one of the interfaces — slot/port or VLAN number.
PAGE 805
Usage Information The interface group command will create all the non-existent VLANs specified in the range. On successful command execution, the CLI switches to the interface group context. The configuration commands inside the group context will be the similar to that of the existing range command. Note: For release 9.4(0.0), the group command is supported only for VLANs and physical interfaces.
PAGE 806
Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.4.1.0 Introduced Example Dell(conf)#interface loopback 1655 Dell(conf-if-lo-1655)# Related Commands interface — configures a physical interface.
PAGE 807
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S55, S60, and S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a Management port. The Management port is enabled by default (no shutdown).
PAGE 808
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Usage Information You cannot delete the Null interface.
PAGE 809
Parameters interface {slot/ port | port} — port}, interface {slot/port | port} — port},... Enter interface range and one of the interfaces and then slot/port, port-channel, or VLAN number information. Select the range of interfaces for bulk configuration. You can enter up to six comma-separated ranges. Spaces are not required between the commas. The ranges can include VLANs, portchannels, and physical interfaces. • For a port channel interface, enter the keywords portchannel then a number.
PAGE 810
Usage Information When creating an interface range, interfaces appear in the order they are entered; they are not sorted. The command verifies that interfaces are present (physical) or configured (logical). Important Points to Remember: • Bulk configuration is created if at least one interface is valid. • Non-existing interfaces are excluded from the bulk configuration with a warning message. • The interface range prompt includes interface types with slot/port information for valid interfaces.
PAGE 811
Example (Multiple Range) This example shows how to use commas to add different interface types to the range enabling all Tengigabit Ethernet interfaces in the range 5/1 to 5/23 and both Tengigabit Ethernet interfaces 1/1 and 1/2.
PAGE 812
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Tunnel interface, enter the keyword tunnel then the tunnel ID. The range is from 1 to 16383. For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. • Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 813
Related Commands interface range – configures a range of command (bulk configuration) interface range macro name – runs an interface range macro. interface range macro name Run the interface-range macro to automatically configure the pre-defined range of interfaces. Syntax Parameters interface range macro name name Enter the name of an existing macro. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 814
interface range macro (define) — defines a macro for an interface range (bulk configuration). interface vlan Configure a VLAN. You can configure up to 4094 VLANs. Syntax Parameters interface vlan vlan-id [of-instance{of-id}] of-instance{ofid} Enter the keyword of-instance then the OpenFlow instance ID to add the VLAN to the specified OpenFlow instance. The range is from 1 to 8. NOTE: Associate the OpenFlow instance with the VLAN when the VLAN is created.
PAGE 815
• IPv4 • IPv6 • MTU If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously. Example (Single Range) Dell(conf)#int vlan 3 Dell(conf-if-vl-3)# Related Commands interface — configures a physical interface. interface loopback — configures a loopback interface. interface null — configures a null interface. interface port-channel — configures a port channel group. show vlan — displays the current VLAN configuration on the switch.
PAGE 816
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.16.1 Introduced on the MXL 10/40GbE Switch IO Module. If you configure interface type as CR4 with auto-negotiation enabled, also configure CR4 with auto-negotiation. Many DAC cable link issues are resolved by setting the interface type as CR4. • Interfaces — configures a physical interface. • interface loopback — configures a loopback interface.
PAGE 817
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. When you configure keepalive, the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive, the system does not send keepalive packets and so the local end of a WAN link remains up even if the remote end is down. negotiation auto Enable auto-negotiation on an interface.
PAGE 818
The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits. The negotiation auto command provides a mode option for configuring an individual port to forced-master/forced slave after you enable auto-negotiation. NOTE: The mode option is not available on non-10/100/1000/10G Base-T Ethernet line cards. If you do not use the mode option, the default setting is slave.
PAGE 819
User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces.
PAGE 820
information. The slot range is from 0 to1. The port range is 0. • For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 821
Example (Single Interface) Key Description m Change the view from a single interface to all interfaces on the line card or visa-versa. c Refresh the view. b Change the counters displayed from Packets on the interface to Bytes. r Change the [delta] column from change in the number of packets/bytes in the last interval to rate per second. l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis.
PAGE 822
Te 0/1 Down 0 0 0 0 Te 0/2 Up 61512 52 66160 42 Te 0/3 Up 63086 20 9405888 24 Te 0/4 Up 14697471418 2661481 13392989657 2661385 Te 0/5 Up 3759 3 161959604 832816 Te 0/6 Up 4070 3 8680346 5 Te 0/7 Up 61934 34 138734357 72 Te 0/8 Up 61427 1 59960 1 Te 0/9 Up 62039 53 104239232 3 Te 0/10 Up 17740044091 372 7373849244 79 Te 0/11 Up 18182889225 44 7184747584 138 Te 0/12 Up 18182682056 0 3682 1 Te 0/13 Up 18182681434 43 6592378911 144 Te 0/14 Up 61349 55 86281941 15 Te 0/15 Up 59808 58 62060 27 Te 0/16 Up 59889 1
PAGE 823
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 824
Layer 2 Overhead Link MTU and IP MTU Delta Untagged Packet with VLAN-Stack Header 22 bytes Tagged Packet with VLAN-Stack Header 26 bytes portmode hybrid To accept both tagged and untagged frames, set a physical port or port-channel. A port configured this way is identified as a hybrid port in report displays. Syntax portmode hybrid To return a port to accept either tagged or untagged frames (non-hybrid), use the no portmode hybrid command.
PAGE 825
VLAN 20, and an untagged member of VLAN 10, which becomes the native VLAN of the port. The port now accepts: • untagged frames and classify them as VLAN 10 frames • VLAN 20 tagged frames The following describes the do show interfaces command shown in the following example. This example shows output with “Hybrid” as the newly added value for 802.1QTagged.
PAGE 826
rate-interval Configure the traffic sampling interval on the selected interface. Syntax Parameters rate-interval seconds seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds. NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value. For example, if 44 seconds is designated, it rounds to 30; 45 to 59 seconds rounds to 45.
PAGE 827
show config Display the interface configuration. Syntax show config Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000.
PAGE 828
Command Modes CONFIGURATION INTERFACE (conf-if-range) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 829
Command Modes Command History Interfaces • EXEC • EXEC Privilege • For stack-units, enter the keywords stack-unit then the slot/port information. The range is from 0 to 11. • For a Null interface, enter the keyword null then the Null interface number. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 830
Usage Information Version Description 6.3.1.0 Added the Pluggable Media Type field in the E-Series TeraScale output. Use the show interfaces command for details on a specific interface. NOTE: In the CLI output, the power value is rounded to a 3-digit value. For receive/transmit power that is less than 0.000, an snmp query returns the corresponding dbm value even though the CLI displays as 0.000.
PAGE 831
Line Description LineSpeed Displays the interface’s line speed, duplex mode, and negotiation mode. ARP type:... Displays the ARP type and the ARP timeout value for the interface. Last clearing... Displays the time when the show interfaces counters where cleared. Queuing strategy... States the packet queuing strategy. FIFO means first in first out.
PAGE 832
Line Description – discarded = number of packets discarded without any processing – collisions = number of packet collisions – wred=count both packets discarded in the MAC and in the hardware-based queues Rate information... Estimate of the input and output traffic rate over a designated interval (30 to 299 seconds). Traffic rate is displayed in bits, packets per second, and percent of line rate. Time since... Elapsed time since the last interface status change (hh:mm:ss format).
PAGE 833
Example (1G SFP) Dell#show interfaces tengigabitethernet 2/1 TenGigabitEthernet 2/1 is up, line protocol is down Hardware is Force10Eth, address is 00:01:e8:41:77:95 Current address is 00:01:e8:41:77:95 Pluggable media present, SFP type is 1000BASE-SX Wavelength is 850nm Interface index is 100974648 Port will not be disabled on partial SFM failure Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit Flowcontrol rx on tx on ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "
PAGE 834
Example (Management Ethernet, two IPv6 addresses) Dell#show interfaces managementethernet 0/0 ManagementEthernet 0/0 is up, line protocol is up Hardware is DellForce10Eth, address is 00:01:e8:a0:bf:f3 Current address is 00:01:e8:a0:bf:f3 Pluggable media not present Interface index is 302006472 Internet address is 10.16.130.
PAGE 835
of-instance: 2 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:05:12 Queueing strategy: fifo Time since last interface status change: 00:05:12 Related Commands show interfaces configured – displays any interface with a non-default configuration. show interfaces switchport – displays Layer 2 information about the interfaces.
PAGE 836
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Changed the organization of the display output. Example Dell#show interfaces configured TenGigabitEthernet 13/18 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.
PAGE 837
Parameters interface (Optional) Enter one of the following keywords and slot/port or number information: • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 838
Related Commands dampening — configures dampening on an interface. show interfaces — displays information on a specific physical interface or virtual interface. show interfaces configured — displays any interface with a non-default configuration. show interfaces phy Display auto-negotiation and link partner information. Syntax Parameters show interfaces gigabitethernet slot/port phy tengigabitether net Enter the keyword tengigabitethernet then the slot or port information.
PAGE 839
autoNegComplete field and the linkstatus field read “True.” AutoNegotiatio n Advertise Displays the control words the local interface advertises during negotiation. Duplex is either half or full. Asym- and Sym Pause is the types of flow control the local interface supports. AutoNegotiatio n Remote Partner’s Ability Displays the control words the remote interface advertises during negotiation. Duplex is either half or full. Asym- and Sym Pause is the types of flow control the remote interface supports.
PAGE 840
Example Dell#show interfaces tengigabitethernet 1/0 phy Mode Control: SpeedSelection: 10b AutoNeg: ON Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete: False RemoteFault: False LinkStatus: False JabberDetect: False AutoNegotation Advertise: 100MegFullDplx: True 100MegHalfDplx: True 10MegFullDplx: False 10MegHalfDplx: True Asym Pause: False Sym Pause: False AutoNegotiation Remote Partner's Ability: 100MegFullDplx: False 100MegHalfDplx: False 10MegFullDplx: False
PAGE 841
Command Modes Command History Usage Information Interfaces • EXEC • EXEC Privilege • For the management interface on the RPM, enter the keyword ManagementEthernet followed by the slot/ port information. The slot range is 0-1 and the port range is 0. • For the Null interface, enter the keywords null 0. • For a Port Channel interface, enter the keywords portchannel followed by a number. For the C-Series and SSeries, the range is 1 to 128.
PAGE 842
Field Description OK? Indicates if the hardware is functioning properly. Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface. Description Displays the description (if any) manually configured for the interface.
PAGE 843
Parameters unit-number Enter the stack member number. The range is from 0 to 11 for the S4810. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Interfaces Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 844
Current address is 00:01:e8:4c:f2:83 !-------------output truncated ----------------! Related Commands show hardware stack-unit — displays data plane and management plane input/ output statistics. show interfaces — displays information on a specific physical interface or virtual interface. show interfaces status To display status information on a specific interface only, display a summary of interface information or specify a stack-unit slot and interface.
PAGE 845
Example Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 846
stack-unit unitid • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a backup interface for this interface, enter the keyword backup. (OPTIONAL) Enter the keywords stack-unit then the stack member number.
PAGE 847
Example Items Description 802.1QTagged Displays whether if the VLAN tagged (“True”), untagged (“False”), or hybrid (“Hybrid”), which supports both untagged and tagged VLANs by port 13/0. Vlan membership Lists the VLANs to which the interface is a member. Starting with Dell Networking OS version 7.6.1, this field can display native VLAN membership by port 13/0. Dell#show interfaces switchport Name: TenGigabitEthernet 13/1 802.
PAGE 848
Parameters tengigabitether net For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. fortyGigE For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 849
Interfaces Line Description Bias High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 850
Line Description Voltage Current voltage of the SFPs. If this voltage crosses voltage high alarm/warning thresholds, the voltage high alarm/ warning flag is set to true. Tx Bias Current Present transmission (Tx) bias current of the SFP. If this crosses bias high alarm/warning thresholds, the TX bias high alarm/warning flag is set to true. If it falls below the low alarm/warning thresholds, the TX bias low alarm/warning flag is set to true. Tx Power Present Tx power of the SFP.
PAGE 851
Example Line Description Temperature Low Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above. Voltage Low Alarm Flag This can be either true or false, depending on the Current voltage value displayed above. Tx Bias Low Alarm Flag This can be either true or false, depending on the Tx bias current value displayed above. Tx Power Low Alarm Flag This can be either true or false, depending on the Current Tx power value displayed above.
PAGE 852
SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP 0 0 0 0 0 0 0 0 0 0 0 0 0 Length(50um) 10m = 0x1e Length(62.
PAGE 853
=================================== !-------output truncated ------------------------Related Commands interface — configures a physical interface on the switch. show ip interface — displays Layer 3 information about the interfaces. show interfaces — displays information on a specific physical interface or virtual interface.
PAGE 854
Output Statistics: 0 packets, 0 bytes, 0 underruns Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show range Display all interfaces configured using the interface range command. S5000 Syntax show range Command Modes INTERFACE RANGE (config-if-range) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 855
show interfaces — displays information on a specific physical interface or virtual interface. show running-config ecmp-group Display interfaces, LAG, or LAG link bundles being monitored for uneven traffic distribution using the ecmp-group monitoring enable command. The ECMP group could have a LAG or a list of 10G/40 interfaces (not just LAG link-bundles). S5000 Syntax show running-config ecmp-group Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 856
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 857
speed (for 10/100/1000 interfaces) Set the speed for 10/100/1000 Base-T Ethernet interfaces. Set both sides of a link to the same speed (10/100/1000) or to auto or the link may not come up. S5000 Syntax speed {10 | 100 | 1000 | auto} To return to the default setting, use the no speed {10 | 100 | 1000} command. Parameters 10 Enter the keyword 10 to set the interface’s speed to 10 Mb/s. NOTE: This interface speed is not supported on the LCEH-GE-50P or the LC-EJ-GE-50P card.
PAGE 858
Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Supported on LC-EH-GE-50P or the LC-EJ-GE-50P cards. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information This command is found on the 10/100/1000 Base-T Ethernet interfaces. When you enable auto, the system performs an automatic discovery to determine the optics installed and configure the appropriate speed.
PAGE 859
1000 Enter the keyword 1000 to set the interface to autonegotiate its speed. auto Enter the keyword auto to set the interface to autonegotiate its speed. Defaults auto Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON.
PAGE 860
Parameters stack-unit Enter the stack member unit identifier of the stack member to reset. number Enter the port number of the 40G port to be split. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.
PAGE 861
switchport Place an interface in Layer 2 mode. S5000 Syntax switchport [backup interface {gigabit slot/port | tengigabit slot/port | fortyGigE slot/port | port-channel number}] To remove an interface from Layer 2 mode and place it in Layer 3 mode, enter the no switchport command. If a switchport backup interface is configured, first remove the backup configuration.
PAGE 862
Usage Information Version Description 8.4.1.0 Added support for port-channel interfaces (the portchannel number option). 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Added the backup interface option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface.
PAGE 863
Parameters applicationtype all Enter any of the following keywords: • For DNS, enter the keyword dns. • For FTP, enter the keyword ftp. • For NTP, enter the keyword ntp. • For Radius, enter the keyword radius. • For sFlow collectors, enter the keyword sflowcollector. • For SNMP (traps and MIB responses), enter the keywords snmp . • For SSH, enter the keyword ssh . • For Syslog, enter the keyword syslog. • For TACACS, enter the keyword tacacs. • For Telnet, enter the keyword telnet.
PAGE 864
Parameters applicationtype all Enter any of the following keywords: • For HTTP, enter the keyword http. • For ICMP, enter the keyword icmp. Configure all applications. Defaults None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.3.
PAGE 865
Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 866
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T. Dell#show ip management-eis-route Destination Gateway ----------------10.11.0.0/16 ManagementEthernet 0/0 172.16.1.0/24 10.11.192.
PAGE 867
show management application pkt-fallback-cntr Display the number of packets for each application type that have been rerouted to the default routing table due to management port or route lookup failure. S5000 Syntax show management application pkt—fallback-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 868
NOTE: The Dell Networking OS implementation of LAG or Port Channel requires that you configure a LAG on both switches manually. For information about Dell Networking OS link aggregation control protocol (LACP) for dynamic LAGs, refer to the Link Aggregation Control Protocol (LACP) chapter. For more information about configuring and using Port Channels, refer to the Dell Networking OS Configuration Guide. channel-member Add an interface to the Port Channel, while in INTERFACE PORTCHANNEL mode.
PAGE 869
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Use the interface port-channel command to access this command. You cannot add an interface to a Port Channel if the interface contains an IP address in its configuration. Only the shutdown, description, mtu, and ip mtu commands can be configured on an interface if it is added to a Port Channel.
PAGE 870
shutdown — disables/enables the port channel. group Group two LAGs in a supergroup (“fate-sharing group” or “failover group”). Syntax group group_number port-channel number port-channel number To remove an existing LAG supergroup, use the no group group_number command. Parameters group_number Enter an integer from 1 to 32 that uniquely identifies this LAG fate-sharing group. port-channel number Enter the keywords port-channel then an existing LAG number.
PAGE 871
show interfaces port-channel — displays information on configured Port Channel groups. interface port-channel Create a Port Channel interface, which is a link aggregation group (LAG) containing 16 physical interfaces on the S-Series. S5000 Syntax interface port-channel channel-number To delete a Port Channel, use the no interface port-channel channelnumber command. Parameters channelnumber For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 872
The shutdown, description, and name commands are the only commands that you can configure on an interface while it is a member of a Port Channel. To add a physical interface to a Port Channel, the interface can only have the shutdown, description, and name commands configured. The Port Channel’s configuration is applied to the interfaces within the Port Channel. A Port Channel can contain both 100/1000 interfaces and GE interfaces.
PAGE 873
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 874
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. Usage Information This feature groups two LAGs to work in tandem as a supergroup.
PAGE 875
Example Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. Dell(conf-if-po-1)#show config ! interface Port-channel 1 no ip address shutdown Dell(conf-if-po-1)# show interfaces port-channel Display information on configured Port Channel groups.
PAGE 876
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. Modified to display the LAG failover group status. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information 876 The following describes the show interfaces port-channel command shown in the following example. Field Description Port-Channel 1... Displays the LAG’s status.
PAGE 877
Example Field Description Received 0... Displays the type and number of errors or other specific packets received. This information is displayed over three lines. Output 0... Displays the type and number of packets sent out the interface. This information is displayed over three lines. Rate information... Displays the traffic rate information into and out of the interface. Traffic rate is displayed in bits and packets per second. Time since...
PAGE 878
Field Description • Status Example L2 — for Layer 2 Displays the status of the port channel. • down — if the port channel is disabled (shutdown) • up — if the port channel is enabled (no shutdown) Uptime Displays the age of the port channel in hours:minutes:seconds. Ports Lists the interfaces assigned to this port channel. (untitled) Displays the status of the physical interfaces (up or down).
PAGE 879
incominginterface interface Enter the keywords incoming-interface then the interface type and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. source-ip address Enter the keywords source-ip then the IP source address in IP address format.
PAGE 880
MAC-based hashing is configured for a Layer 2 interface and you are trying to display a Layer 3 flow. The output displays three entries: • Egress port for unfragmented packets. • In the event of fragmented packets, the egress port of the first fragment. • In the event of fragmented packets, the egress port of the subsequent fragments. NOTE: In the show port channel flow command output, the egress port for an unknown unicast, multicast, or broadcast traffic is not displayed.
PAGE 881
S5000 Syntax Parameters tdr-cable-test interface interface Enter the keyword TenGigabitEthernet then the slot/port information for the 10G Ethernet interface. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.7.0.0 Introduced on the S5000.
PAGE 882
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 9.7.0.0 Introduced on the S5000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.
PAGE 883
Related Commands tdr-cable-test — runs the TDR test. UDP Broadcast The user datagram protocol (UDP) broadcast feature is a software-based method to forward low throughput (not to exceed 200 pps) IP/UDP broadcast traffic arriving on a physical or VLAN interface. Important Points to Remember • This feature is available only on the platform. • Routing information protocol (RIP) is not supported with the UDP Broadcast feature.
PAGE 884
Example Dell#debug ip udp-helper UDP helper debugging is on 01:20:22: Pkt rcvd on Gi 5/0 with IP DA (0xffffffff) will be sent on Gi 5/1 Gi 5/2 Vlan 3 01:44:54: Pkt rcvd on Gi 7/0 is handed over for DHCP processing. Related Commands ip udp-broadcast-address — configures a UDP IP address for broadcast. ip udp-helper udp-port — enables the UDP broadcast feature on an interface. show ip udp-helper — displays the configured UDP helper(s) on all interfaces.
PAGE 885
Related Commands debug ip udp-helper — enables debug and displays the debug information on a console. show ip udp-helper — displays the configured UDP helpers on all interfaces. ip udp-helper udp-port Enable the UDP broadcast feature on an interface either for all UDP ports or a specified list of UDP ports. Syntax ip udp-helper udp-port [udp-port-list] To disable the UDP broadcast on a port, use the no ip udp-helper udp-port [udp-port-list] command.
PAGE 886
If you only configure the ip udp-helper udp-port command, all the UDP broadcast traffic is flooded, including ports 67/68 traffic if those ports are part of the udp-port-list. Related Commands ip helper-address — configures the destination broadcast or host address for the DHCP server. debug ip udp-helper — enables debug and displays the debug information on a console. show ip udp-helper — displays the configured UDP helpers on all interfaces.
PAGE 887
ip udp-helper udp-port — enables the UDP broadcast feature on an interface either for all UDP ports or a specified list of UDP ports.
PAGE 888
25 Fabric Services Commands The following commands are supported for Fabric Services operation on the S5000. active-zoneset Activate the zoneset. S5000 Syntax active-zoneset zoneset_name To change to the default zone behavior, use the no active-zoneset zoneset_name command. Parameters Command Modes Command History zoneset_name Enter the zoneset name. FC FABRIC CONFIGURATION Version 9.1(1.0) Introduced on the S5000.
PAGE 889
Parameters number Trace level used to record FC information in the dump file. Range: 1 to 4, where: • 0 turns FC traces off. • 1 records FC error messages. • 2 records FC warning messages. • 3 records FC informational messages. • 4 records all messages generated for FC operation on the switch. Default: 4. Defaults Trace level 4: All FC error messages on the switch are recorded in the FC dump file. Command Modes • EXEC • EXEC Privilege Command History Version 9.0(1.
PAGE 890
Command History Version 9.0(1.3) Introduced on the S5000. Usage Information Use the clear counters fibrechannel command to clear the statistics (counters) displayed in show interfaces fibrechannel command output for a specified FC port. Example Dell(conf)#clear counters fibrechannel 0/11 Clear counters on Fc 0/11 [confirm] yes Related Commands interface fibrechannel — configures a Fibre Channel interface on the switch.
PAGE 891
fc alias Create a zone alias name. S5000 Syntax fc alias ZoneAliasName To delete a zone alias name, use the no fc zone ZoneAliasName command. Parameters Command Modes Command History ZoneAliasName Enter the zone alias name. CONFIGURATION Version 9.1(1.0) Introduced on the S5000. Example Dell(conf)#fc alias za1 Dell(conf-fc-alias-za1)# Related Commands show fc alias — displays the configured alias.
PAGE 892
Usage Information All Fabric-Services mode CLI commands are enabled after changing to FabricServices mode. When you run the fc switch-mode fabric-services command, the following warning message displays: • Warning!!: Switch mode in running-config will be changed to 'fabric-services' :Continue? [yes/no]: – no – No effect on the running-config. – yes – Changes the running-config to reflect the new switch-mode.
PAGE 893
Related Commands show fc zone — displays the configured zone. show fcoe-map — displays the fabric parameters. fc zoneset Create a zoneset. S5000 Syntax fc zoneset zoneset_name To delete a zoneset, use the no fc zoneset zoneset_name command. Parameters Command Modes Command History zoneset_name Enter the zoneset name. CONFIGURATION Version 9.1(1.0) Introduced on the S5000.
PAGE 894
Command Modes Command History Usage Information CONFIGURATION INTERFACE Version 9.0(1.3) Introduced on the S5000. An FCoE map is a template used to map FCoE and FC parameters in a converged fabric. An FCoE map is used to virtualize upstream FC ports on an S5000 NPIV proxy gateway so that they appear to downstream server CNA ports as FCoE forwarder (FCF) ports on an FCoE network.
PAGE 895
Command History Usage Information Version 9.0(1.3) Introduced on the S5000. Use this command to configure the S5000 to interoperate with Fibre Channel devices in SAN fabrics. Enter the no feature fc command to disable the Fibre Channel command-line interface and free memory resources allocated to Fibre Channel operation. Example Dell(conf)#feature fc Related Commands show interfaces fibrechannel — displays the configuration of a Fibre Channel interface. member — alias Add devices to an alias.
PAGE 896
member — zone Add devices to a zone. S5000 Syntax member name To remove devices from the zone, use the no member name command Parameters Command Modes Command History name Enter the WWPN, FC-ID, or Alias name. ZONE CONFIGURATION Version 9.1(1.0) Introduced on the S5000. Example Dell(conf)# fc zone z1 Dell(conf-fc-zone-z1)# member 11:11:11:11:11:11:11:11 Related Commands show fc zone — displays the configured zone. show fc zoneset — displays the configured and active zoneset.
PAGE 897
Related Commands show fc zoneset — displays the configured and active zoneset. show fc alias Display the configured alias. S5000 Syntax Parameters Command Modes Command History Example show fc alias [ZoneAliasName ] ZoneAliasNam e • EXEC • EXEC Privilege Version 9.1(1.0) Enter the zone alias name to display the details. Introduced on the S5000. Dell#show fc alias Zone Alias Name 0x030303 al1 Dell# Related Commands fc alias — creates a zone alias name.
PAGE 898
Command History Example Related Commands Version 9.1(1.0) Introduced on the S5000. Dell#show fc fabric Number of FC Switches = 2 Domain Id Switch WWN 1* 10:00:5c:f9:dd:ef:0a:00 2 10:00:5c:f9:dd:ef:0a:80 Dell# Switch Name Sonoma Sonoma Mgmt IP addr 127.10.11.11 127.10.11.11 fc switch-mode fabric-services — change the switch mode from NPIV Gateway (NPG) mode to fabric-services mode. show fc lsdb Display link state database information on the switch.
PAGE 899
LocalPort RemotePort LinkCost NeighborID LocalPort RemotePort LinkCost Switch Name DomainId Switch Port Hops Cost Age LinkCount NeighborID LocalPort RemotePort LinkCost NeighborID LocalPort RemotePort LinkCost Dell# 1 1 125 3 3 3 125 10:00:5c:f9:dd:ef:16:80 3 3 1 125 1 2 1 1 3 250 2 3 3 125 show fc ns Display the devices in the name server database.
PAGE 900
Port Name 10:00:8c:7c:ff:17:f8:01 Node Name 20:00:8c:7c:ff:17:f8:01 Class of Service 8 IP Address Symbolic Port Name Brocade-1860 | 3.0.3.
PAGE 901
Registered for SCN Dell# Yes Dell#show fc ns fabric brief Total number of devices = 2 Intf# Domain FC-ID EnodeWWPN Enode-WWNN 9 2 02:09:00 32:11:0e:fc:00:00:00:88 22:11:0e:fc:00:00:00:88 11 2 02:0b:00 31:11:0e:fc:00:00:00:77 21:11:0e:fc:00:00:00:77 Dell# show fc route Display the fc route table on the switch. S5000 Syntax show fc route Parameters None Command Modes • EXEC • EXEC Privilege Command History Example Version 9.1(1.0) Introduced on the S5000.
PAGE 902
show fc switch Display the switch configuration for Fibre Channel capability. S5000 Syntax show fc switch Parameters None Command Modes • EXEC • EXEC Privilege Command History Usage Information Version 9.0(1.3) Introduced on the S5000. The following table describes the show fc switch output shown in the following example. Switch Mode Fibre Channel mode of operation of an S5000 switch. Default: NPG (configured as an NPIV proxy gateway).
PAGE 903
Command Modes Command History Example • • EXEC EXEC Privilege Version 9.1(1.0) Introduced on the S5000. Dell#show fc topology Local Port Info _____________________ Port FC 0/1 Port WWN 20:01:5c:f9:dd:ef:24:40 Port Type E Remote Link Information _____________________ Port Type Domain Id Port Name Node Name E 01 20:03:5c:f9:dd:ef:1b:80 10:00:5c:f9:dd:ef:1b:80 Dell# show fc-trace-level Display the currently configured FC trace level.
PAGE 904
Example Dell#show fc-trace-level FC Trace Level = 4 (All) Dell# Related Commands change fc-trace-level— changes the FC trace level used to record FC information in the trace log. show fc zone Display the configured zone. S5000 Syntax Parameters Command Modes Command History Example show fc zone [zonename ] zonename • EXEC • EXEC Privilege Version 9.1(1.0) Enter the zone name to display the details. Introduced on the S5000.
PAGE 905
show fc zoneset Display the configured and active zoneset. S5000 Syntax Parameters Command Modes Command History Example show fc zoneset [ zoneset_name | active | merged ] zoneset_name Enter the zoneset name to display the zoneset name active Enter the keyword active to display the active zonesets. merged Enter the keyword merged to display the merge active zones. • EXEC • EXEC Privilege Version 9.1(1.0) Introduced on the S5000.
PAGE 906
Related Commands fc zone — creates a zone. fc zoneset — creates a zoneset. active-zoneset — activates the zoneset. member - alias — adds devices to an alias. member - zone — adds devices to a zone. member - zoneset — adds zones into a zoneset.
PAGE 907
Fibre Channel Interface Commands 26 The following commands are supported for Fibre Channel operation on the S5000. fabric Configure the SAN fabric to which a Fibre Channel port connects. S5000 Syntax Parameters fabric fcoe-map fcoe-map Enter the name of the FCoE map which contains the FCoE/FC fabric to which the Fibre Channel port connects. Defaults None Command Modes INTERFACE FIBRE_CHANNEL Command History Usage Information Version 9.0(1.3) Introduced on the S5000.
PAGE 908
interface fibrechannel Configure a Fibre Channel (FC) interface on the switch. S5000 Syntax Parameters interface fibrechannel slot/port slot/port For slot, enter the stack-unit number assigned to the switch. The range of slot (stack-unit) numbers is from 0 to 11. The range of port numbers is from 0 to 47. NOTE: In release 9.0.(1.3), an FC module can be installed only in expansion slot 0 (ports 0 to 11) on an S5000 switch.
PAGE 909
server CNA ports. When you enable a fabric-facing FC port, the FCoE map applied on the port starts sending FIP multicast advertisements using the parameters in the FCoE map over server-facing Ethernet ports. A server sees the FC port with its applied FCoE map as an FCF port. Example Dell(conf)#interface fibrechannel 3/0 Dell(conf-if-fc-3/0)#exit# Related Commands show interfaces fibrechannel — displays the configuration of a Fibre Channel interface.
PAGE 910
Table 1. Output Fields for the show interfaces fibrechannel Command Field Description Information: Fibrechannel 0/0 is down, FC link is down Administrative state. of the Fibre Channel interface (up/ enabled or down/ shutdown) and operational state of the FC link (up or down) Pluggable media present, SFP+ type Pluggable optic is. inserted in the port or not, and the SFP+ optic type Wavelength Wavelength of the. inserted optic SFP+ receive power Power received on.
PAGE 911
Field Description WWN, FC-ID Factory-provided. world-wide name (WWN) of FC port (in hexadecimal) that uniquely identifies the port on the switch (not userconfigurable) and the unique FC port ID (24-bit in hexadecimal) received from an FC switch in the fabric after a successful login Last clearing of "show interface" counters Elapsed time since. the interface counters displayed in show interfaces output were last cleared Statistics: BBCR_FrameFailures BBCR_RRDYFrameFailures Number of link.
PAGE 912
Field Class3Discards Number of Class 3. frames dropped DecodeErrors Number of decode. errors FBusy FReject AddressErrors LinkFailures InvalidCRC Number of Fabric. port Busy (F_BSY) frames received Number of Fabric. port Reject (F_RJT) frames received Number of frame-. address ID errors Number of link. failures Number of cyclic redundancy check (CRC) errors TotalRxBytes Number of bytes. received TotalTxBytes Number of bytes. transmitted LongFramesIn LossOfSync ShortFramesIn Number of long.
PAGE 913
Field Description RxOfflineSequences Number of offline. sequences received TxOfflineSequences Number of offline. sequences transmitted TotalOfflineSequences Total number of. offline sequences Rate Information: Input bytes/sec, frames/sec, % of line-rate Incoming rate of FC. traffic in bytes per second, frames per second, and percentage of the total line rate Output bytes/sec, frames/sec, % of line-rate Outgoing rate of FC.
PAGE 914
LinkFailures 0 TxOfflineSeq 3 InvalidCRC 0 TotalOfflineSeq 4 Rate info: Input 0 bytes/sec, 0 frames/sec, 0.00% of line-rate Output 0 bytes/sec, 0 frames/sec, 0.00% of line-rate Time since last interface status change: 03:00:35 Related Commands interface fibrechannel — configures a Fibre Channel interface on the switch. speed Set the speed of a Fibre Channel port or configure the port to auto-negotiate its speed with a peer.
PAGE 915
Passthrough Commands The following are passthrough commands supported on the S5000. show stack-unit port-group portmode Display the fibre channel port-group mode information. S5000 Syntax Parameters Command Modes Command History show system stack-unit unit-number port-group portmode stack-unit unitnumber • EXEC • EXEC Privilege Version 9.1(1.0) Enter the keywords stack-unit then the unit number. The range is from 0 to 11. Introduced on the S5000.
PAGE 916
Parameters Command Modes Command History stack-unit unitnumber Enter the keywords stack-unit then the unit number. The range is from 0 to 11. port-group number Enter the keywords port-group then the number of the port-group. The range is from 0 to 5. portmode Enter the keyword portmode then the keyword ethernet to enable Ethernet mode. CONFIGURATION Version 9.1(1.0) Introduced on the S5000.
PAGE 917
27 Enhanced Validation of Interface Ranges This functionality is supported on the platform. You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as interface range fo 2/0-1,te 10/0,gi 3/0,fa 0/0, this configuration is considered valid. The comma-separated list is not required to be separated by spaces in between the ranges.
PAGE 918
Internet Protocol Security (IPSec) 28 Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: • Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 919
To delete a transform set, use the no crypto ipsec transform-set name {ah-authentication {md5|sha1|null} | esp-authentication {md5| sha1|null} | esp-encryption {3des|cbc|des|null}} command. Parameters name Enter the name for the transform set. ahauthentication Enter the keywords ah-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic.
PAGE 920
Version Description 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. Usage Information • Both sides of the link must specify the same transform set. • You can create up to 64 transform sets. Example Dell(conf)#do show crypto ipsec transform-set Transform-Set Name Transform-Set refCnt AH Transform ESP Auth Transform ESP Encry Transform : ts1 : 0 : md5 : : Dell(conf)# crypto ipsec policy Create a crypto policy used by ipsec.
PAGE 921
Example Dell(conf)#crypto ipsec policy West 10 ipsec-manual Dell(conf-crypto-policy)# management crypto-policy Apply the crypto policy to management traffic. Syntax management crypto-policy name To remove the management traffic crypto policy, use the no management crypto-policy name command. Parameters name Enter the name for the crypto policy.. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 922
Parameters seq-num Enter the match command sequence number. sourceipaddress | ipv6 address Enter the keyword source then the IPv4 or IPv6 address for the source. mask Enter the mask prefix length in /nn format. source-port number Enter the source port number. destinationport number Enter the destination port number. Defaults none Command Modes CONFIG-CRYPTO-POLICY Command History This guide is platform-specific.
PAGE 923
To delete the session key information from the crypto policy, use the no session-key {inbound | outbound} {ah | esp} command. Parameters name Enter the name for the transform set. inbound Specify the inbound session key for IPSec. outbound Specify the outbound session key for IPSec. ah Use the AH protocol when you select the AH transform set in the crypto policy. esp Use the ESP protocol when you select the ESP transform set in the crypto policy. spi Enter the security parameter index number.
PAGE 924
Parameters name Enter the name of the transform set. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
PAGE 925
Inbound ESP Encry SPI : Inbound AH Key : Inbound ESP Auth Key : Inbound ESP Encry Key : Outbound AH SPI : Outbound ESP Auth SPI : Outbound ESP Encry SPI: Outound AH Key : Outound ESP Auth Key : Outound ESP Encry Key : Match sequence Num Protocol type IP or IPv6 Source address Source mask Source port Destination address Destination mask Destination port source-interface name source-interface num 0 [0]:: [0]:: [0]:: 0 0 0 [0]:: [0]:: [0]:: : : : : : : : : : : : 2 tcp IP 1.1.1.1 /32 0 1.1.1.
PAGE 926
Version Description 9.2(0.2) Introduced on the Z9000, S4810, and S4820T.
PAGE 927
29 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the platform. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). S5000 Syntax arp ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF. Use the VRF option after the keyword arp to configure a static arp on that particular VRF.
PAGE 928
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 929
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases. This behavior reduces the potential for the system to slow down while waiting for a multitude of ARP responses.
PAGE 930
1. At time t=0, Dell Networking OS sends an ARP request for IP A.B.C.D. 2. At time t=1, Dell Networking OS receives an ARP request for IP A.B.C.D. 3. At time t=2, Dell Networking OS installs an ARP entry for A.B.C.D only on RP2. Beginning with Dell Networking OS version 8.3.1.0, when a gratuitous ARP is received, Dell Networking OS installs an ARP entry on all three CPUs. arp max-entries Enables you to configure the maximum number of ARP entries per VRF that are allowed for IPv4..
PAGE 931
arp retries Set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. Syntax arp retries number Parameters number Enter the number of retries. The range is from 1 to 20. The default is 5. Defaults 5 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 932
Defaults 240 minutes (4 hours) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 933
• For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ip ip-address (OPTIONAL) Enter the keyword ip then the IP address of the ARP entry you wish to clear.
PAGE 934
clear host Remove one or all dynamically learned host table entries. Syntax Parameters clear host name name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 935
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.19.0 Introduced on the S4820T.
PAGE 936
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information You cannot use this attribute to clear routes corresponding to a management VRF. Related Commands ip route — assigns an IP route to the switch.
PAGE 937
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. debug arp View information on ARP transactions. S5000 Syntax debug arp [interface] [count value] To stop debugging ARP transactions, use the no debug arp command.
PAGE 938
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.
PAGE 939
Example IPv4 Routing Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series.
PAGE 940
Related Commands ip helper-address – specifies the destination broadcast or host address for the DHCP server request. ip helper-address hop-count disable – disables the hop-count increment for the DHCP relay agent. debug ip icmp View information on the internal control message protocol (ICMP). S5000 Syntax debug ip icmp [interface] [count value] To disable debugging, use the no debug ip icmp command.
PAGE 941
Example Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option.
PAGE 942
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. The slot range is from 0 to 1. The port range is 0. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 943
Field Description d= Lists the destination address of the packet and the name of the interface (in parentheses) through which the packet is being sent out on the network. len Displays the packet’s length. sending, rcvd, fragment, sending broad/multicast proto, unroutable The last part of each line lists the status of the packet. TCP src= Displays the source and destination ports, the sequence number, the acknowledgement number, and the window size of the packets in that TCP packets.
PAGE 944
The access-group option supports only the equal to (eq) operator in TCP ACL rules. Port operators not equal to (neq), greater than (gt), less than (lt), or range are not supported in access-group option (refer to the following example). ARP packets (arp) and Ether-type (ether-type) are also not supported in the accessgroup option. The entire rule is skipped to compose the filter.
PAGE 945
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 946
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. ip domain-list Configure names to complete unqualified host names. Syntax ip domain-list name To remove the name, use the no ip domain-list name command.
PAGE 947
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To configure a list of possible domain names, configure the ip domain-list command up to six times. If you configure both the ip domain-name and ip domain-list commands, the software tries to resolve the name using the ip domain-name command.
PAGE 948
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To fully enable DNS, also specify one or more domain name servers with the ip name-server command. Dell Networking OS does not support sending DNS queries over a VLAN.
PAGE 949
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You can only configure one domain name with the ip domain-name command. To configure more than one domain name, configure the ip domain-list command up to six times.
PAGE 950
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 951
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 952
ip address Enter an IP address, in dotted decimal format, to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 953
NOTE: When you configure the capability to enable the loopback IP address to be sent for easy debugging and diagnosis (IP addresses of the devices for which the ICMP source interface is configured), the source IP address of the outgoing ICMP error message is modified, although the packets are not sent out using the configured interface.
PAGE 954
Example Dell(conf)#ip icmp source-interface tengigabitethernet 1/1 Dell(conf)# ipv6 icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv6 packets.
PAGE 955
Usage Information You can enable the mechanism to configure the source or the originating interface from which the packet (the device that generates the ICMP error messages) is received by the switch to send the loopback address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output. The loopback address must be unique in a particular domain.
PAGE 956
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series. To avoid denial of service (DOS) attacks, keep the number of fragments allowed for re-assembly low.
PAGE 957
Usage Information Version 8.1.1.0 Introduced on the E-Series ExaScale. pre-Version 6.1.1.0 Introduced on the E-Series. When you enter the no mtu command, Dell Networking OS reduces the ip mtu value to 1536 bytes. To return the IP MTU value to the default, use the no ip mtu command. Starting with Dell Networking OS Release 9.2(0.2), the ip mtu command is not supported to configure the IP MTU value that is used when the IP packet is fragmented.
PAGE 958
Related Commands Layer 2 Overhead Difference between Link MTU and IP MTU Tagged Packet with VLAN-Stack Header 26 bytes mtu — sets the link MTU for an Ethernet interface. ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command.
PAGE 959
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out on all other interfaces, including the Management port. You can separately configure both IPv4 and IPv6 domain name servers. ip proxy-arp Enable proxy ARP on an interface. Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled.
PAGE 960
ip route Assign a static route to the switch. Syntax ip route ip-address mask {ip-address | interface [ip-address]} [distance] [permanent] [tag tag-value] [vrf vrf-name] [weight weight-value] To delete a specific static route, use the no ip route destination mask command. To delete all routes matching a certain route, use the no ip route destination mask command. Parameters destination Enter the IP address in dotted decimal format of the destination device.
PAGE 961
interface ipaddress Enter the keyword interface then the IP address. distance (OPTIONAL) Enter the value of the distance metric assigned to the route. The range is from 1 to 255. permanent (OPTIONAL) Enter the keyword permanent to specify that the route must not be removed even if the interface assigned to that route goes down. The route must be currently active to be installed in the routing table. If you disable the interface, the route is removed from the routing table.
PAGE 962
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Using the following example of a static route: ip route 33.33.33.0 /24 tengigabitethernet 1/1 172.31.5.
PAGE 963
ip source-route Enable Dell Networking OS to forward IP packets with source route information in the header. Syntax ip source-route To drop packets with source route information, use the no ip route-source command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 964
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 965
• mac {dest-mac | source-destmac | sourcemac} tcp-udp enable Enter the keywords to distribute MAC traffic based on the following criteria: • dest-mac — Uses the destination MAC address, VLAN, Ethertype, source module ID and source port ID fields to hash. The hashing mechanism returns a 3-bit index indicating which port the packet should be forwarded. • source-dest-mac — Uses the destination and source MAC address, VLAN, Ethertype, source module ID and source port ID fields to hash.
PAGE 966
management route Configure a static route that points to the Management interface or a forwarding router. Syntax management route {{ip-address mask | {ipv6-address prefixlength}} {forwarding-router-address | managementethernet | fortyGigE | vlan | tengigabitethernet} To remove a static route, use the no management route{{ip-address mask | {ipv6-address prefix-length}}{forwarding-router-address | managementethernet | fortyGigE | vlan | gigabitethernet | tengigabitethernet} command.
PAGE 967
Version Description 9.7(0.0) Added support for forty gigabit, vlan, and tengigabit ethernet interfaces. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000 and added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 968
• For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ip ip-address mask (OPTIONAL) Enter the keyword ip then an IP address in the dotted decimal format. Enter the optional IP address mask in the slash prefix format (/ x).
PAGE 969
Usage Information Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.8.1.0 Augmented to display local ARP entries learned from private VLANs (PVLANs). 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following example shows two VLANs that are associated with a private VLAN (PVLAN) (refer to Private VLAN (PVLAN)).
PAGE 970
Example (Private VLAN) NOTE: In this example, Line 1 shows community VLAN 200 (in primary VLAN 10) in a PVLAN. Line 2 shows primary VLAN 10. Dell#show arp Protocol Address Age(min) Hardware Address Interface VLAN CPU --------------------------------------------------------------Internet 5.5.5.1 - 00:01:e8:43:96:5e Vl 10 pv 200 CP Internet 5.5.5.10 - 00:01:e8:44:99:55 Vl 10 CP Internet 10.1.2.4 1 00:01:e8:d5:9e:e2 Ma 0/0 CP Internet 10.10.10.4 1 00:01:e8:d5:9e:e2 Ma 0/0 CP Internet 10.16.127.
PAGE 971
show arp retries Display the configured number of ARP retries. Syntax show arp retries Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 972
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6 addresses. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show hosts command in the following example. Field Description Default domain...
PAGE 973
Example Related Commands Dell#show hosts Default domain is not set Name/address lookup uses static Name servers are not set Host Flags TTL Type -------- -------- ---ks (perm, OK) IP 4200-1 (perm, OK) IP 1230-3 (perm, OK) IP ZZr (perm, OK) IP Z10-3 (perm, OK) IP Dell# mappings Address ------2.2.2.2 192.68.69.2 192.68.99.2 192.71.18.2 192.71.23.1 traceroute — views the DNS resolution. ip host — configures a host.
PAGE 974
summary (OPTIONAL) Enter the keyword summary to view a table listing route prefixes and the total number routes which can be entered in to CAM. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.7(0.
PAGE 975
1.1.1.1/32 1.1.1.0/24 Dell# 0 0 1 1 0 0 00:00:00:00:00:00 00:00:00:00:00:00 Example (ECMP-Group) Dell#show ip cam stack-unit 3 po 0 ecmp-group detail Example (Member-Info) Dell#show ip cam stack-unit 3 po 0 ecmp-group member-info detail CP CP Destination EC C VId Mac-Addr Port ECMP Group-Index -----------------------------------------------------------------------------------------1.1.1.2/32 0 0 1000 00:01:00:00:00:02 Te 3/42 2.1.1.2/32 0 0 20 00:03:00:00:00:02 Po 10 2.1.1.
PAGE 976
ip-address mask (OPTIONAL) Enter the IP address of the network destination to view only information on that destination. Enter the IP address in dotted decimal format (A.B.C.D). Enter the mask in slash prefix format (/X). longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. summary (OPTIONAL) Enter the keyword summary to view the total number of prefixes in the FIB.
PAGE 977
If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named W-EC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is assigned with a weight. Example Dell#show ip fib stack-unit 1 Destination Gateway First-Hop MacAddr Port VId EC -----------------------------------------------------------------------------------------1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Te 3/42 1000 0 2.1.1.2/32 via 2.1.1.2, Vl 20 2.1.
PAGE 978
show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface. Syntax Parameters show ip flow interface interface {source-ip address destination-ip address} {protocol number [tcp | udp]} {src-port number destination-port number} interface interface Enter the keyword interface then one of the following interface keywords. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 979
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command provides egress port information for a given IP flow. This information is useful in identifying which interface the packet follows in the case of Port-channel and Equal Cost Multi Paths. Use this command for routed packed only.
PAGE 980
information. The slot range is from 0 to 1. The port range is 0. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. • For a stack-unit interface, enter the keyword stackunit then the stack unit number. • For a tunnel interface, enter the keyword tunnel then the tunnel interface number.
PAGE 981
Example Lines Description TenGigabitEthern et 1/1... Displays the interface’s type, slot/port, and physical and line protocol status. Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed. IP MTU is... Displays IP MTU value. Inbound access... Displays the name of the configured incoming access list. If none is configured, the phrase “not set” is displayed. Proxy ARP...
PAGE 982
Example (Brief) Dell#show ip interface brief Interface IP-Address Status Protocol TenGigabitEthernet 1/0 unassigned administratively down down TenGigabitEthernet 1/1 unassigned administratively down down TenGigabitEthernet 1/2 unassigned up up TenGigabitEthernet 1/3 unassigned up up TenGigabitEthernet 1/4 unassigned up up TenGigabitEthernet 1/5 10.10.10.
PAGE 983
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell#show ip management-route Destination ----------10.1.2.0/24 172.16.1.0/24 Dell# Gateway ------ManagementEthernet 0/0 10.1.2.
PAGE 984
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Introduced on the C- and E-Series. 8.3.7.0 Introduced on the S4810.
PAGE 985
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell#show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.3 Router Id is set to 20.20.20.
PAGE 986
NOTE: bgp, isis, ospf, and rip. • If you enter bgp, you can include the BGP as-number . • If you enter isis, you can include the ISIS routingtag. • If you enter ospf, you can include the OSPF processid. process-id (OPTIONAL) Specify that only OSPF routes with a certain process ID must be displayed. routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes.
PAGE 987
Usage Information The following describes the show ip route all command in the following example.
PAGE 988
N2- OSPF NSSA external type 2, E1 - OSPF external type 1 E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1 L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default >- non-active route + - summary route Gateway of last resort is not set Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------R 3.0.0.0/8 via 100.10.10.10, Te 2/8 120/1 00:07:12 via 101.10.10.10, Te 2/9 100.10.10.0/24 Direct, Te 2/8 0/0 00:08:54 > R 100.10.10.0/24 Direct, Te 2/8 120/0 00:08:54 C 101.
PAGE 989
0/0 C 1/16 0/0 00:01:32 6.6.6.0/24 Direct, Te 00:01:25 Dell# show ip route 1.1.1.0/24 Routing entry for 1.1.1.0/24 Known via "static", distance 1, metric 0 Last update 00:05:01 ago Routing Descriptor Blocks: * 4.4.4.2, via TenGigabitEthernet 1/4 weight 100 * 6.6.6.2, via TenGigabitEthernet 1/16 weight 200 Dell(conf)# Example (With Weighted ECMP Disabled) Dell(conf)#ip route 1.1.1.0/24 6.6.6.2 weight 100 Dell(conf)#ip route 1.1.1.0/24 6.6.6.
PAGE 990
show ip route list Display IP routes in an IP prefix list. Syntax Parameters Command Modes Command History show ip route vrf vrf-name list prefix-list prefix-list • • Enter the name of a configured prefix list. EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.
PAGE 991
R C Related Commands 2.1.3.0/24 2.1.4.0/24 via 2.1.4.1, Te 4/43 Direct, Te 4/43 120/1 0/0 3d1h 3d1h ip prefix-list — enters CONFIGURATION-IP PREFIX-LIST mode and configures a prefix list. show ip prefix-list summary — displays a summary of the configured prefix lists. show ip route summary View a table summarizing the IP routes in the switch. Syntax show ip route summary Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 992
Example Column Heading Description Active Routes Identifies the best route if a route is learned from two protocol sources. Non-active Routes Identifies the back-up routes when a route is learned by two different protocols. If the best route or active route goes down, the non-active route becomes the best route. ospf 100 If routing protocols (OSPF, RIP) are configured and routes are advertised, then information on those routes is displayed. Total 1388 active...
PAGE 993
rp2 (OPTIONAL) Enter the keyword rp2 to view only the statistics from Route Processor 2. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information IPv4 Routing Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 994
Keyword Definition ... timeouts Number of times a timer expired on a reassembled queue. ... too big Number of invalid IP fragments received. ... couldn’t fragment Number of packets that could not be fragmented and forwarded. ...encapsulation failed Counts packets which could not be forwarded due to ARP resolution failure. Dell Networking OS sends an arp request prior to forwarding an IP packet. If a reply is not received, Dell Networking OS repeats the request three times.
PAGE 995
Bcast: 28 received, 0 sent; Mcast: 0 received, 0 sent Sent: 16048 generated, 0 forwarded 21 encapsulation failed, 0 no route ICMP statistics: Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 0 unreachable 0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench 0 parameter, 0 timestamp, 0 info request, 0 other Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply 0 mask requests, 0 mask replies, 0 quench, 0 timestamp 0 info reply, 0 time exceeded, 0 parameter problem UDP statistics: Rcvd: 0 to
PAGE 996
Usage Information 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 6.4.1.0 Introduced The following describes the show tcp statistics cp command shown in the following example. Field Description Rcvd: Displays the number and types of TCP packets received by the switch. 0 checksum error...
PAGE 997
Example Field Description 25 control packets... Displays the number of control packets sent and the number retransmitted. 11603 data packets... Displays the number of data packets sent. 24 data packets retransmitted Displays the number of data packets resent. 355 ack.. Displays the number of acknowledgement packets sent and the number of packet delayed. 0 window probe... Displays the number of window probe and update packets sent. 7 Connections initiated...
PAGE 998
Related Commands 998 show ip cam stack-unit — displays the CAM table.
PAGE 999
IPv6 Access Control Lists (IPv6 ACLs) 30 IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking platform. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl command. • Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. • Reference to an empty ACL permits any traffic.
PAGE 1000
Parameters default l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 Use the default CAM profile settings, and set the CAM as follows: • L3 ACL (ipv4acl): 6 • L2 ACL(l2acl): 5 • IPv6 L3 ACL (ipv6acl): 0 • L3 QoS (ipv4qos): 1 • L2 QoS (l2qos): 1 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor of 2.
PAGE 1001
cam-acl-egress Allocate space for IPv6 egress ACLs. Syntax Parameters cam-acl-egress {default | l2acl 1-4 ipv4acl 1-4 ipv6acl 0-4} default Use the default CAM profile settings, and set the CAM as follows: • • • l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 L2 ACL(l2acl): 1 L3 ACL (ipv4acl: 1 IPv6 L3 ACL (ipv6acl): 2 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 4.
PAGE 1002
l2acl Set L2-ACL entries Dell(conf)#cam-acl-egress l2acl ? <1-4> Number of FP blocks for l2acl Dell(conf)#cam-acl-egress l2acl 1 ? ipv4acl Set IPV4-ACL entries Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ? ipv6acl Set IPV6-ACL entries Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ipv6acl ? <0-4> Number of FP blocks for IPV6 (multiples of 2) Dell(conf)#cam-acl-egress l2acl 1 ipv4acl 1 ipv6acl 2 clear counters ipv6 access-group Erase all counters maintained for the IPv6 access lists.
PAGE 1003
deny Configure a filter that drops IPv6 packets that match the filter criteria. C-Series, E-Series, S-Series Syntax deny {ipv6-protocol-number | icmp | ipv6 | tcp | udp} To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no deny {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command ip-protocolnumber Enter an IPv6 protocol number. The range is 0 to 255.
PAGE 1004
deny icmp Configure a filter to drop all or specific ICMP messages.
PAGE 1005
Version 7.4.1.0 Introduced on the E-Series TeraScale Added the monitor option. deny tcp Configure a filter that drops TCP packets that match the filter criteria.
PAGE 1006
The following list includes some common TCP port numbers: 20 and 21 = FTP • 25 = SMTP • 169 = SNMP Enter the IPv6 address of the network or host to which the packets are sent in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. The :: notation specifies successive hexadecimal fields of zero.
PAGE 1007
Example An ACL rule with a TCP port range of 4000 - 8000 uses eight entries in the CAM: Rule# 1 2 3 4 5 6 7 8 Data Mask 0000111110100000 0000111111000000 0001000000000000 0001100000000000 0001110000000000 0001111000000000 0001111100000000 0001111101000000 From 1111111111100000 1111111111000000 1111100000000000 1111110000000000 1111111000000000 1111111100000000 1111111111000000 1111111111111111 4000 4032 4096 6144 7168 7680 7936 8000 To #Covered 4031 4095 6143 7167 7679 7935 7999 8000 32 64 2048 1
PAGE 1008
mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all routes are subject to the filter. host ipv6address Enter the keyword host followed by the IPv6 address of the host in the x:x:x:x::x format. The :: notation specifies successive hexadecimal fields of zero.
PAGE 1009
ports is configured in the CAM based on bitmask boundaries; the space required depends on exactly what ports are included in the range.
PAGE 1010
filters in the IPv6 ACL, the traffic is permitted instead of dropped). vlan range Defaults Disabled. Command Modes INTERFACE Command History (OPTIONAL) Enter the keyword vlan followed by the VLAN range in a comma separated format. The range is 1 to 4094. Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the S-Series. Version 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters. Prior to version 7.8.1.
PAGE 1011
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. ipv6 access-list Configure an access list based on IPv6 addresses or protocols. Syntax ipv6 access-list access-list-name cpu-qos {permit | deny} ospfv3 To delete an access list, use the no ipv6 access-list access-list-name command.
PAGE 1012
Usage Information Version Description 9.4(0.0) Added support for CoPP for OSPFv3 on the S4810, S4820T, S6000, and Z9000 platforms. 9.0.2.0 Introduced on the S6000 8.3.11.1 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters. Prior to version 7.8.1.
PAGE 1013
udp Enter the keyword udp to filter the User Datagram Protocol. Defaults Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 1014
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series TeraScale. Added the monitor option. permit tcp Configure a filter to pass TCP packets that match the filter criteria.
PAGE 1015
• port port eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two port for the port parameter.) Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is 0 to 65535.
PAGE 1016
Version 7.4.1.0 Introduced on the E-Series TeraScale. Added the monitor option. Usage Information Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (gt, lt, range) may require more than one entry. The range of ports is configured in the CAM based on bitmask boundaries; the space required depends on exactly what ports are included in the range.
PAGE 1017
• Parameters Use the no permit udp {source address mask | any | host ipv6address} {destination address | any | host ipv6-address} command. source address Enter the IPv6 address of the network or host from which the packets were sent in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. The :: notation specifies successive hexadecimal fields of zero. mask Enter a network mask in /prefix format (/x).
PAGE 1018
Version 7.4.1.0 Introduced on the E-Series TeraScale. Added the monitor option. Usage Information Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (gt, lt, range) may require more than one entry. The range of ports is configured in the CAM based on bitmask boundaries; the space required depends on exactly what ports are included in the range.
PAGE 1019
description Defaults Not configured. Command Modes ACCESS-LIST Command History Enter a description of up to 80 characters. Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. Usage Information As shown in the Example below, the same sequence number is used for the remark and an ACL rule.
PAGE 1020
characters. Prior to version 7.8.1.0, names are up to 16 characters long. StartingSeqNu m Enter the starting sequence number to resequence. The range is 0 to 4294967290. Step-toIncrement Enter the step to increment the sequence number. The range is 1 to 4294967290. Defaults none Command Modes • EXEC • EXEC Privilege Command History Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.0 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.
PAGE 1021
Defaults none Command Modes • EXEC • EXEC Privilege Command History Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.0 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. Usage Information When all sequence numbers have been exhausted, this feature permits reassigning new sequence number to entries of an existing access-list.
PAGE 1022
tcp Enter the keyword tcp to configure a Transmission Control protocol filter. udp Enter the keyword udp to configure a User Datagram Protocol filter. source address Enter the IPv6 address of the network or host from which the packets were sent in the x:x:x:x::x format followed by the prefix length in the /x format. The range is /0 to /128. The :: notation specifies successive hexadecimal fields of zero. mask Enter a network mask in /prefix format (/x).
PAGE 1023
byte Defaults Not configured. Command Modes ACCESS-LIST Command History Related Commands (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the E-Series TeraScale and S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the monitor option. deny – configures a filter to drop packets.
PAGE 1024
Example Version Description 7.8.1.0 Introduced on the C-Series.
PAGE 1025
L2Acl Ipv4Acl Ipv6Acl Ipv4Qos L2Qos : : : : : Current Settings(in block sizes) 2 2 4 2 3 Dell#show cam-acl Related Commands cam-acl — configures CAM profiles to support IPv6 ACLs. show cam-acl-egress Show information on FP groups allocated for egress ACLs. Syntax Command Modes Command History show cam-acl-egress • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1026
Ipv4Acl : Ipv6Acl : 1 2 Dell#show cam-acl Related Commands cam-acl — configures CAM profiles to support IPv6 ACLs. show config View the current IPv6 ACL configuration. C-Series, E-Series, S-Series Syntax show config Command Modes ACCESS-LIST Command History Example Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.
PAGE 1027
Parameters Command Modes Command History Usage Information Example access-listname Enter the name of the ACL to be displayed, up to 140 characters. cam_count List the count of the CAM rules for this ACL. interface interface Enter the keyword interface followed by the interface type and slot/port or number information: • EXEC • EXEC Privilege • For a Port Channel interface, enter the keywords portchannel followed by a number. For the C-Series and SSeries, the range is 1 to 128.
PAGE 1028
! Dell# show running-config acl Display the ACL running configuration. C-Series, E-Series, S-Series Syntax show running-config acl Command Modes • EXEC • EXEC Privilege Command History Example Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1029
Parameters policy-map name Enter the name of the policy-map to verify. number Enter all to get information for all the linecards, or enter the linecard number to get information for a specific card. The range is 0-6 for E-Series and 0-7 for C-Series. Defaults none Command Modes EXEC Privilege Command History Usage Information Version 9.0.2.0 Introduced on the S6000. Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.
PAGE 1030
2| Allowed 2| Allowed 4| Allowed 4| Allowed Dell# 1| IPv4Flow| 232| 0| 1| IPv6Flow| 0| 0| 0| IPv4Flow| 232| 0| 0| IPv6Flow| 0| 0| Dell#test cam-usage service-policy input LauraMapTest linecard 4 port-set 0 Linecard|Portpipe|CAM Partition|Available CAM|Estimated CAM per Port|Status ------------------------------------------------------------4| 0| IPv4Flow| 232| 0| Allowed 4| 0| IPv6Flow| 0| 0| Allowed Dell# Dell#test cam-usage service-policy input LauraMapTest linecard 2 port-set 1 Linecard|
PAGE 1031
Defaults Not configured. Command Modes ROUTE-MAP Command History Related Commands Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters. Prior to version 7.8.1.0, the names are up to 16 characters long. Version 7.4.1.0 Introduced on the E-Series TeraScale. match ipv6 next-hop – redistributes routes that match the next-hop IP address.
PAGE 1032
Related Commands match ipv6 address – redistributes routes that match an IP address. match ipv6 route-source – redistributes routes that match routes advertised by other routers. match ipv6 route-source Configure a filter which matches based on the routes advertised in the IPv6 prefix lists. C-Series, E-Series, S-Series Syntax match ipv6 route-source prefix-list prefix-list-name To delete a match, use the no match ipv6 route-source prefix-list prefix-list-name command.
PAGE 1033
route-map Designate a IPv6 route map name and enter ROUTE-MAP mode. C-Series, E-Series, S-Series Syntax route-map map-name To delete a route map, use the no route-map map-name command. Parameters map-name Defaults Not configured. Command Modes ROUTE-MAP Command History Example Enter a text string to name the route map, up to 140 characters. Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series.
PAGE 1034
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults Not configured. Command Modes ROUTE-MAP Command History Usage Information Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale. The set ipv6 next-hop command is the only way to set an IPv6 Next-Hop.
PAGE 1035
show route-map View the current route map configurations. C-Series, E-Series, S-Series Syntax show route-map Command Modes • EXEC • EXEC Privilege Command History Version 8.4.2.1 Introduced on the S-Series. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1036
31 IPv6 Basics IPv6 basic commands are supported on the Dell Networking OS. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide. clear ipv6 fib Clear (refresh) all forwarding information base (FIB) entries on a linecard or stack unit.
PAGE 1037
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series TeraScale. clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. S5000 Syntax Parameters clear ipv6 route [vrf vrf-name] {* | ipv6-address prefixlength} vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF.
PAGE 1038
Version Description 7.4.1.0 Introduced on the E-Series TeraScale. clear ipv6 mld_host Clear the IPv6 MLD host counters and reset the elapsed time. Syntax clear ipv6 mld_host Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T.
PAGE 1039
generated. Valid range is 1 to 100. When warn-threshold is used, once the limit is reached, additional routes will not be allowed into the RTM ( route table manager ) itself. warning-only When the warning-only option is used, a syslog message will be thrown when maximum number of dynamic IPv6 routes reaches the limit. Additional dynamic IPv6 routes will still be allowed. Defaults No limit is set on the maximum number of dynamic IPv6 routes for a VRF.
PAGE 1040
Usage Infomation Version Description 9.1.(0.0) Updated Usage Information section. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. • SAA can configure up to two addresses. If any preferred prefix or valid timers time out, the corresponding address are deprecated or removed. If an address is removed due to a time-out, an address from the current unused prefix is used to create a new address.
PAGE 1041
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example IPv6 Basics Version Description 9.1(0.0) Updated Usage Information. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.1.
PAGE 1042
ipv6 address eui64 Configure IPv6 EUI64 address configuration on the interface. Syntax ipv6 address {ipv6-address prefix-length} eui64 To disable IPv6 EUI64 address autoconfiguration, use the no ipv6 address {ipv6-address prefix-length} eui64 command. Parameters ipv6-address prefix-length Enter the IPv6 prefix in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1043
To restore the default value, use the no ipv6 control-plane icmp errorrate-limit command. Parameters pps Enter the maximum number of error packets generated per second. The range is from 1 to 200, where 0 disables the rate-limiting. Default 100 pps Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1044
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. If the flowlabel value is already set for BGP or SSH, the system defaults to the already configured value. All packets on the same connection are considered part of the same flow by the system. For new connections, set the new flowlabel to zero. ipv6 host Assign a name and IPv6 address the host-to-IPv6 address mapping table uses.
PAGE 1045
ipv6 name-server Enter up to six IPv6 addresses of name servers. The order you enter the addresses determines the order of their use. Syntax ipv6 name-server ipv6-address [ipv6-address2... ipv6-address6] To remove a name server, use the no ipv6 name—server ipv6–address command. Parameters ipv6-address Enter the IPv6 address (X:X:X:X::X) of the name server to be used. Note: The :: notation specifics successive hexadecimal fields of zeros. ipv6-address2...
PAGE 1046
ipv6 nd dad attempts To perform duplicate address detection (DAD) on the management interface, configure the number of neighbor solicitation messages that are sent. Syntax ipv6 nd dad attempts {number of attempts} To restore the default value, use the no ipv6 nd dad attempts command. Parameters number of attempts Enter the number of attempts to be made to detect a duplicate address. The range is from 0 to 15. Setting the value to 0 disables DAD on the interface.
PAGE 1047
no-advertise Enter the keyword no-advertise to prevent the specified prefix from being advertised. no-autoconfig Enter the keywords no-autoconfig to disable Stateless Address Autoconfiguration. no-rtr-address Enter the keyword no-rtr-address to exclude the full router address from router advertisements (the R bit is not set). off-link Enter the keywords off-link to advertise the prefix without stating to recipients that the prefix is either on-link or offlink.
PAGE 1048
ipv6 route Establish a static IPv6 route. S5000 Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6address | interface | interface ipv6-address} [distance] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route [vrf vrf-name]ipv6address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [tag value] [permanent] [weight] command.
PAGE 1049
NOTE: The :: notation specifies successive hexadecimal fields of zeros. distance (OPTIONAL) Enter a number as the metric distance assigned to the route. The range is from 1 to 255. tag value (OPTIONAL) Enter the keyword tag then a tag value number. The range is from 1 to 4294967295. permanent (OPTIONAL) Enter the keyword permanent to specify that the route is not to be removed, even if the interface assigned to that route goes down.
PAGE 1050
recursive resolution is “broken,” Dell Networking OS withdraws the route. The route is re-installed, by Dell Networking OS, when the recursive resolution is satisfied. After an IPv6 static route interface is created, if an IP address is not assigned to a peer interface, the peer must be manually pinged to resolve the neighbor information. You can specify a weight for an IPv4 or IPv6 static route. If the weight value of a path is 0, then that path is not used for forwarding when weighted ECMP is in effect.
PAGE 1051
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series TeraScale. Because this command is enabled by default, it does not appear in the running configuration.
PAGE 1052
summary (OPTIONAL) Enter the keyword summary to display a table listing network prefixes and the total number prefixes which can be entered into the IPv6 CAM. index (OPTIONAL) Enter the index in the IPv6 CAM. ipv6-address Enter the IPv6 address in the x:x:x:x::x/n format to display networks that have more specific prefixes. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1053
show ipv6 control-plane icmp Displays the status of the icmp control-plane setting for the error eate limit setting. Syntax show ipv6 control-plane icmp Default 100 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 8.3.19.
PAGE 1054
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added support for VRF. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.
PAGE 1055
Related Commands ipv6 nd dad attempts — Configure system to set the flow label field in the packets to zero. show ipv6 interface Display the status of interfaces configured for IPv6.
PAGE 1056
fortyGigE (OPTIONAL) View information for an IPv6 fortygigabitethernet interface. stack-unit id (OPTIONAL) View information for stacking. tunnel tunnelid (OPTIONAL) View information for a tunnel interface. vlan (OPTIONAL) View information for IPv6 VLANs. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1057
DAD is enabled, number of DAD attempts: 3 ND reachable time is 39610 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 Dell# Example (Managementet hernet) Dell#show ipv6 interface management 0/0 ManagementEthernet 0/0 is up,
PAGE 1058
ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds ND advertised reachable time is 0 milliseconds ND advertised retransmit interval is 0 milliseconds ND router advertisements are sent every 198 to 600 seconds ND router advertisements live for 1800 seconds ND advertised hop limit is 64 IPv6 hop limit for originated packets is 64 show ipv6 mld_host Display the IPv6 MLD host counters.
PAGE 1059
Example Field Description Malformed Packets The number of MLDv1 and MLDv2 packets that do not match the requirement for a valid MLD packet. MLD Host Traffic Counters Elapsed time since counters cleared: 0028:33:52 Received Sent Valid MLD Packets 97962 18036 Reports 79962 18034 Leaves ---0 MLDv2 Queries 18000 ---MLDv1 Queries 0 ---Errors: Malformed Packets: 4510 show ipv6 route Displays the IPv6 routes.
PAGE 1060
ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes. static (OPTIONAL) View only routes configured by the ipv6 route command. summary (OPTIONAL) View a brief list of the configured IPv6 routes. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1061
Field Example (SSeries) Description • N1 = OSPF NSSA external type 1 • N2 = OSPF NSSA external type 2 • E1 = OSPF external type 1 • E2 = OSPF external type 2 • i = IS-IS • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + = summary routes Destination Identifies the route’s destination IPv6 address. Gateway Identifies whether the route is directly connected and on which interface the route is configured.
PAGE 1062
1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * candidate default, Gateway of last resort is not set C C S L Dell# Example (Summary) Destination Dist/Metric, Gateway, Last Change ----------------------------------------------------100::/64 [0/0] Direct, Te 1/12, 20:00:18 400::/64 [0/0] Direct, Tu 1, 00:09:02 800::/64 [1/0] via 100::1, Te 1/12, 00:00:50 fe80::/10 [0/0] Direct, Nu 0, 20:00:18 show ipv6 route summary: ===============================
PAGE 1063
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Introduced on the E-Series TeraScale. When you configure trust IPv6 diffserv, matched bytes/packets counters are not incremented in the show qos statistics command. Trust diffserv (IPv4) can co-exist with trust ipv6-diffserv in an Input Policy Map.
PAGE 1064
32 IPv6 Border Gateway Protocol (IPv6 BGP) IPv6 Border Gateway Protocol (IPv6 BGP) is supported on Dell Networking platforms. This chapter includes the following sections: • IPv6 BGP Commands • IPv6 MBGP Commands IPv6 BGP Commands BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless interdomain routing and the aggregation of routes and AS paths.
PAGE 1065
includes AS_PATH and community information from the routes included in the aggregated route. attribute-map map-name (OPTIONAL) Enter the keywords attribute-map then the name of a configured route map to modify attributes of the aggregate, excluding AS_PATH and NEXT_HOP attributes. summary-only (OPTIONAL) Enter the keywords summary-only to advertise only the aggregate address. Specific routes are not advertised.
PAGE 1066
In the show ip bgp ipv6 unicast command, aggregates contain an ‘a’ in the first column and routes suppressed by the aggregate contain an ‘s’ in the first column. bgp always-compare-med Allows you to enable comparison of the MULTI_EXIT_DISC (MED) attributes in the paths from different external ASs. Syntax bgp always-compare-med To disable comparison of MED, use the no bgp always-compare-med command. Defaults Disabled (that is, the software only compares MEDs from neighbors within the same AS).
PAGE 1067
bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations. Syntax bgp bestpath as-path ignore To return to the default, use the no bgp bestpath as-path ignore command. Defaults Disabled (that is, the software considers the AS_PATH when choosing a route as best). Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1068
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1069
Usage Information The MED is a 4-byte unsigned integer value and the default behavior is to assume a missing MED as 4294967295. This command causes a missing MED to be treated as 0. During path selection, paths with a lower MED are preferred over those with a higher MED. bgp client-to-client reflection Allows you to enable route reflection between clients in a cluster. Syntax bgp client-to-client reflection To disable client-to-client reflection, use the no bgp client-to-client reflection command.
PAGE 1070
bgp cluster-id Assign a cluster ID to a BGP cluster with more than one route reflector. Syntax bgp cluster-id {ip-address | number} To delete a cluster ID, use the no bgp cluster-id {ip-address | number} command. Parameters ip-address Enter an IP address as the route reflector cluster ID. number Enter a route reflector cluster ID as a number from 1 to 4294967295. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1071
bgp confederation identifier Configure an identifier for a BGP confederation. Syntax bgp confederation identifier as-number To delete a BGP confederation identifier, use the no bgp confederation identifier as-number command. Parameters as-number Enter the AS number. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1072
To remove bgp confederation peers, use the no bgp confederation peer command. Parameters as-number Enter the AS number. The range is 1 to 65535. ...as-number (OPTIONAL) Enter up to 16 confederation numbers. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1073
half-life period expires. The range is from 1 to 45. The default is 15 minutes. reuse (OPTIONAL) Enter a number as the reuse value, which is compared to the flapping route’s Penalty value. If the Penalty value is less than the reuse value, the flapping route is once again advertised (or no longer suppressed). The range is from 1 to 20000. The default is 750. suppress (OPTIONAL) Enter a number as the suppress value, which is compared to the flapping route’s Penalty value.
PAGE 1074
bgp default local-preference Change the default local preference value for routes exchanged between internal BGP peers. Syntax bgp default local-preference value To return to the default value, use the no bgp default local-preference command. Parameters value Enter a number to assign to routes as the degree of preference for those routes. When routes are compared, the higher the degree of preference or local preference value, the more the route is preferred. The range is from 0 to 4294967295.
PAGE 1075
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1076
Usage Information The bgp fast-external-failover command appears in the show config command output. bgp four-octet-as-support Enable 4-byte support for the BGP process. Syntax bgp four-octet-as-support To disable fast external fallover, use the no bgp four-octet-as-support command. Defaults Disabled (supports 2-Byte format) Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1077
bgp graceful-restart Enable graceful restart on a BGP neighbor, a BGP node, or designate a local router to support graceful restart as a receiver only. Syntax bgp graceful-restart [restart-time seconds] [stale-path-time seconds] [role receiver-only] To return to the default, enter the no bgp graceful-restart command.
PAGE 1078
bgp log-neighbor-changes Enable logging of BGP neighbor resets. Syntax bgp log-neighbor-changes To disable logging, use the no bgp log-neighbor-changes command. Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T.
PAGE 1079
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1080
Usage Information Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. This command is a knob to disable BGP next-hop resolution using BGP learned routes. During the next-hop resolution, only the first route that the next-hop resolves through is verified for the route’s protocol source and is checked if the route is learned from BGP or not.
PAGE 1081
quite common. In a large scale configuration, filtering millions of routes based on regular expressions can be quite CPU intensive, as a regular expression evaluation involves generation and evaluation of complex finite state machines. BGP policies, containing regular expressions to match as-path and communities, tend to use a lot of CPU processing time, which in turn affects the BGP routing convergence.
PAGE 1082
Usage Information Peering sessions are reset when you change the router ID of a BGP router. bgp soft-reconfig-backup Use this command only when route-refresh is not negotiated between peers to avoid having a peer resend BGP updates. Syntax bgp soft-reconfig-backup To return to the default setting, use the no bgp soft-reconfig-backup command. Defaults Off Command Modes ROUTER BGPV6 ADDRESS FAMILY (conf-router_bgpv6_af) Command History This guide is platform-specific.
PAGE 1083
capture bgp-pdu max-buffer-size Set the size of the BGP packet capture buffer. This buffer size pertains to both IPv4 and IPv6 addresses. Syntax Parameters capture bgp-pdu max-buffer-size 100-102400000 100-10240000 0 Enter a size for the capture buffer. Defaults 40960000 bytes Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1084
Parameters ipv6-address Enter the IPv6 address of the target BGP neighbor. direction {both | rx | tx} Enter the keyword direction and a direction — either rx for inbound, tx for outbound, or both. Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1085
ipv6 unicast soft [in | out] (OPTIONAL) Enter the keywords ipv6 multicast soft [in | out] to set options within the specified IPv6 address family. soft (OPTIONAL) Enter the keyword soft to configure and activate policies without resetting the BGP TCP session, that is, BGP Soft Reconfiguration. NOTE: If you enter clear ip bgp ip6-address soft, both inbound and outbound policies are reset. in (OPTIONAL) Enter the keyword in to activate only inbound policies.
PAGE 1086
flap-statistics (OPTIONAL) Enter the keywords flap-statistics to clear all flap statistics belonging to that AS or a specified address family within that AS. ipv4 (OPTIONAL) Enter the keyword ipv4 to select options for that address family. ipv6 (OPTIONAL) Enter the keyword ipv6 to select options for that address family. unicast (OPTIONAL) Enter the keyword unicast to select the unicast option within the selected address family.
PAGE 1087
clear ip bgp ipv6-address Reset BGP sessions specific to an IPv6 address. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection. Syntax Parameters clear ip bgp ipv6-address [flap-statistics | ipv4 {multicast {flap-statistics | soft {in | out}} | unicast {flap-statistics | soft {in | out}} | ipv6 unicast {flap-statistics | soft {in | out}| soft [in | out] ipv6-address Enter an IPv6 address to reset neighbors belonging to that IP.
PAGE 1088
Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. clear ip bgp peer-group Reset a peer-group’s BGP sessions. Syntax Parameters clear ip bgp peer-group peer-group-name peer-groupname Enter the peer group name to reset the BGP sessions within that peer group. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1089
NOTE: The :: notation specifies successive hexadecimal fields of zeros. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.
PAGE 1090
• ? (question mark) matches sequences in a pattern (0 or 1 sequences) • [ ] (brackets) matches a range of single-character patterns. • ^ (caret) matches the beginning of the input string. (If the caret is used at the beginning of a sequence or range, it matches on everything BUT the characters specified.) • $ (dollar sign) matches the end of the output string. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1091
ipv4-neighboraddr | ipv6neighbor-addr Clear and reapply policies for a neighbor. peer-group name Clear and reapply policies for all BGP routers in the specified peer group. ipv6 unicast Clear and reapply policies for all IPv6 unicast routes. in Reapply only inbound policies. NOTE: If you enter soft, without an in or out option, both inbound and outbound policies are reset. out Reapply only outbound policies.
PAGE 1092
Parameters ipv6-address (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-group peer-groupname Enter the keywords peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only information on inbound BGP routes. out (OPTIONAL) Enter the keyword out to view only information on outbound BGP routes.
PAGE 1093
debug ip bgp events Allows you to view information on local BGP state changes and other BGP events. Syntax debug ip bgp [ipv6-address | peer-group peer-group-name] events [in | out] To disable debugging, use the no debug ip bgp ipv6-address | peergroup peer-group-name] events command. Parameters ipv6-address (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128.
PAGE 1094
debug ip bgp ipv6 dampening View information on dampened (non-active) IPv6 routes. Syntax debug ip bgp ipv6 unicast dampening [in | out] To disable debugging, use the no debug ip bgp ipv6 unicast dampening command. Parameters in (OPTIONAL) Enter the keyword in to view only inbound dampened routes. out (OPTIONAL) Enter the keyword out to view only outbound dampened routes. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1095
To disable debugging, use the no debug ip bgp [ipv4-address | ipv6address | peer-group-name] ipv6 unicast soft-reconfiguration command. Parameters ipv4-address | ipv6-address Enter the IP address of the neighbor on which you want to enable soft-reconfiguration debugging. peer-groupname Enter the name of the peer group on which you want to enable soft-reconfiguration debugging. ipv6 unicast Debug soft reconfiguration for IPv6 unicast routes. Defaults Disabled.
PAGE 1096
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810.
PAGE 1097
Usage Information Version Description 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced This command enables soft-reconfiguration for the specified BGP neighbor. BGP stores all updates for inbound IPv6 unicast routes the neighbor receives but does not reset the peer-session. CAUTION: Inbound update storage is a memory-intensive operation.
PAGE 1098
The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. Entering a no debug ip bgp command removes all configured debug commands for BGP. debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors.
PAGE 1099
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. Entering a no debug ip bgp command removes all configured debug commands for BGP. debug ip bgp updates Allows you to view information about BGP updates.
PAGE 1100
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1101
Usage Information The default-metric command in BGP sets the value of the BGP MULTI_EXIT_DISC (MED) attribute for redistributed routes only. Related Commands bgp always-compare-med – enables comparison of all BGP MED attributes. redistribute – redistributes routes from other routing protocols into BGP. description Enter a description of the BGP routing protocol. Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1102
distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command. Parameters Defaults externaldistance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internaldistance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200.
PAGE 1103
Routes from confederations are treated as internal BGP routes. maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. Syntax maximum-paths {ebgp | ibgp} number To return to the default values, use the no maximum-paths command. Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipath support for Internal BGP routes.
PAGE 1104
neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI. Syntax neighbor {ipv6-address | peer-group-name} activate To disable, use the no neighbor {ipv6-address | peer-group-name} activate command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Identify a peer group by name.
PAGE 1105
neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. Syntax neighbor {ipv6-address | peer-group-name} advertisementinterval seconds To return to the default value, use the no neighbor {ipv6-address | peergroup-name} advertisement-interval command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1106
neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peergroup-name} allowas-in command. Parameters ip-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1107
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ipv6-address | peer-group-name} default-originate [route-map map-name] To remove a default route, use the no neighbor {ipv6-address | peergroup-name} default-originate [route-map map-name] command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1108
neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). Syntax neighbor {ipv6-address | peer-group-name} description text To delete a description, use the no neighbor {ipv6-address | peer-groupname} description text command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group.
PAGE 1109
To delete a neighbor distribution list, use the no neighbor {ipv6-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. prefix-listname Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes).
PAGE 1110
To disallow and disconnect connections, use the no neighbor {ipv6-address | peer-group-name} ebgp-multihop [ttl] command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. ttl (OPTIONAL) Enter the number of hops as the time to live (ttl) value. The range is from 1 to 255. The default is 255. Defaults Disabled.
PAGE 1111
NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. Defaults Disabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.
PAGE 1112
peer-groupname Enter the name of the peer group to apply the filter to all routers in the peer group. in Enter the keyword in to filter inbound BGP routes. out Enter the keyword out to filter outbound BGP routes. Defaults Not configured. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1113
this percentage of the maximum value, the software sends a message. The range is from 1 to 100 percent. The default is 75. warning-only (OPTIONAL) Enter the keyword warning-only to set the router to send a log message when the maximum value is reached. If this parameter is not set, the router stops peering when the maximum number of prefixes is reached. Defaults threshold = 75 Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific.
PAGE 1114
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname (OPTIONAL) Enter the name of the peer group. Defaults Disabled. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1115
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.
PAGE 1116
neighbor peer-group (creating group) Allows you to create a peer group and assign it a name. Syntax neighbor peer-group-name peer-group To delete a peer group, use the no neighbor peer-group-name peer-group command. Parameters peer-groupname Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1117
neighbor peer-group passive Enable passive peering on a BGP peer group; that is, the peer group does not send an OPEN message, but does respond to one. Syntax neighbor peer-group-name peer-group passive To delete a passive peer-group, use the no neighbor peer-group-name peer-group passive command. Parameters peer-groupname Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1118
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter a text string up to 16 characters long as the name of the peer group. number Enter a number of the AS. The range is from 1 to 65535. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1119
NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group to remove the private AS numbers. Defaults Disabled (that is, the private AS number are not removed). Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1120
NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. map-name Enter the name of an established route map. If the Route map is not configured, the default is deny (to drop all routes). in Enter the keyword in to filter inbound routes. out Enter the keyword out to filter outbound routes. Defaults Not configured. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific.
PAGE 1121
To indicate that the neighbor is not a route reflector client or to delete a route reflector configuration, use the no neighbor {ipv6-address | peer-groupname} route-reflector-client command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. All routers in the peer group receive routes from a route reflector. Defaults Not configured.
PAGE 1122
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. All routers in the peer group receive routes from a route reflector. Defaults Not configured and COMMUNITY attributes are not sent to neighbors. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 1123
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1124
Command Modes ROUTER BGPv6 ADDRESS FAMILY (conf-router_bgpv6_af) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 8.4.1.0 Added support for IPv4 multicast and IPv4 unicast address families. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Introduced on the S4810.
PAGE 1125
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1126
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1127
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1128
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. In the system best path selection process, the path with the highest weight value is preferred. NOTE: To apply the weight to the connection and recompute the best path, reset the neighbor connection (the capture bgp-pdu max-buffer-size * command).
PAGE 1129
network Specify the networks for the BGP process and enter them in the BGP routing table. Syntax network ipv6-address prefix-length [route-map map-name] To remove a network, use the no network ip-address mask [route-map map-name] command. Parameters ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1130
Usage Information The software resolves the network address configured by the network command with the routes in the main routing table to ensure that the networks are reachable using non-BGP routes and non-default routes. Related Commands redistribute – redistributes routes into BGP. network backdoor Specify this IGP route as the preferred route. Syntax network ipv6-address prefix-length backdoor To remove a network, use the no network ipv6-address prefix-length backdoor command.
PAGE 1131
redistribute Redistribute routes into BGP. Syntax redistribute {connected | static} [route-map map-name] To disable redistribution, use the no redistribution {connected | static} command. Parameters connected Enter the keyword connected to redistribute routes from physically connected interfaces. static Enter the keyword static to redistribute manually configured routes. These routes are treated as incomplete routes.
PAGE 1132
To redistribute the default route (0::0/0), configure the neighbor defaultoriginate command. Related Commands neighbor default-originate – injects the default route. redistribute isis Redistribute IS-IS routes into BGP. Syntax redistribute isis [level-1 | level-1-2 | level-2] [metric metric-value | metric-type {external | internal}] [route-map map-name] To stop redistribution of IS-IS routes, use the no redistribute isis command.
PAGE 1133
Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1134
Defaults Not configured. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.
PAGE 1135
Version 7.4.1.0 Introduced on the E-Series TeraScale. show capture bgp-pdu neighbor Display BGP packet capture information for an IPv6 address. Syntax Parameters Defaults show capture bgp-pdu neighbor ipv6-address ipv6-address • EXEC • EXEC Privilege Enter the IPv6 address (X:X:X:X::X) of a BGP neighbor. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1136
show config View the current ROUTER BGP configuration.
PAGE 1137
summary Display a summary of RPF routes. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Related Commands Version Description 9.0.0.0 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. ipv6 prefix-list — configures an IPv6 prefix-list. show ip bgp ipv6 unicast View the current BGP information.
PAGE 1138
Usage Information Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. When you enable the bgp non-deterministic-med command, the show ip bgp command output for a BGP route does not list the INACTIVE reason. show ip bgp ipv6 unicast cluster-list View BGP neighbors in a specific cluster.
PAGE 1139
Paramters communitynumber Enter the community number in AA:NN format where AA is the AS number (2 bytes) and NN is a value specific to that autonomous system. You can specify up to eight community numbers to view information on those community groups. local-AS Enter the keywords local-AS to view all routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED. All routes with the NO_EXPORT_SUBCONFED (0xFFFFFF03) community attribute must not be advertised to external BGP peers.
PAGE 1140
show ip bgp ipv6 unicast community-list View routes that are affected by a specific community list. Syntax Paramters show ip bgp ipv6 unicast community-list community-list-name [exact-match] communitylist-name Enter the name of a configured IP community list. exact-match (OPTIONAL) Enter the keywords exact-match to display only for an exact match of the communities. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1141
Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. show ip bgp ipv6 unicast detail Display BGP internal information for IPv6 Unicast address family. Syntax show ip bgp ipv6 unicast detail Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1142
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.
PAGE 1143
Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale. show ip bgp ipv6 unicast flap-statistics View flap statistics on BGP routes. Syntax Parameters show ip bgp ipv6 unicast flap-statistics [ipv6-address prefixlength] [filter-list as-path-name] [regexp regular-expression] ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format.
PAGE 1144
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1145
show ip bgp ipv6 unicast neighbors Displays information on IPv6 unicast routes exchanged by BGP neighbors. Syntax Parameters show ip bgp ipv6 unicast neighbors [ipv4-neighbor-addr | ipv6neighbor-addr] [advertised-routes | dampened-routes | detail | flap-statistics | routes | received-routes [network [networkmask]] | denied-routes [network [network-mask]]] ipv6 unicast Enter the keywords ipv6 unicast to view information only related to IPv6 unicast routes.
PAGE 1146
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.1.0 Added support for IPv4 multicast and IPv6 unicast address families Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the S4810. Version 7.7.
PAGE 1147
Example Lines Beginning With Description Sent messages The line displays the number of BGP messages sent, the number of notifications (error messages), and the number of messages waiting in a queue for processing. Received updates This line displays the number of BGP updates received and sent. Soft reconfiguration This line indicates that soft reconfiguration inbound is configured. Minimum time Displays the minimum time, in seconds, between advertisements.
PAGE 1148
Sent 48 messages, 0 in queue 3 opens, 2 notifications, 0 updates 43 keepalives, 0 route refresh requests Minimum time between advertisement runs is 30 seconds Minimum time before advertisements start is 0 seconds Capabilities received from neighbor for IPv6 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv6 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) For address family: IPv6 Unicast BGP table version 12, neighbor versi
PAGE 1149
'OPEN error/Bad AS' Sent : 0 Recv: 1 Local host: 5ffe:11::4, Local port: 179 Related Commands show ip bgp ipv6 unicast – views the current BGP routing table. show ip bgp ipv6 unicast peer-group Allows you to view information on the BGP peers in a peer group. Syntax Parameters show ip bgp ipv6 unicast peer-group [peer-group-name [summary]] peer-groupname (OPTIONAL) Enter the name of a peer group to view information about that peer group only.
PAGE 1150
Number of peers in this group 1 Peer-group members (* - outbound optimized): 9000::4: Peer-group RR-CLIENT-PASSIV, remote AS 18508 BGP version 4 Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP neighbor is RR-CLIENT-PASSIV, peer-group internal, Number of peers in this group 1 Peer-group members (* - outbound optimized): 9000::9:2* Dell# show ip bgp ipv6 unicast summary Allows you to view the status of all BGP connections.
PAGE 1151
9000::4:2 9000::5:2 9000::6:2 9000::7:2 9000::8:2 9000::9:2 9000::a:2 9000::b:14 Dell# 18508 1 2 3 18508 18508 18508 18508 0 35 35 35 35 44 35 29 0 32 32 32 32 19 32 29 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 never Active 00:16:42 0 00:16:39 0 00:16:41 0 00:16:42 0 00:16:41 0 00:16:43 0 00:13:01 0 show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status.
PAGE 1152
show ip bgp paths View all the BGP path attributes in the BGP database. Syntax Parameters show ip bgp paths [regexp regular-expression] regexp regularexpression Enter a regular expression then use one or a combination of the following characters to match: • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pattern (0 or more sequences). • + = (plus) the sequences in a pattern (1 or more sequences).
PAGE 1153
show ip bgp paths as-path View all unique AS-PATHs in the BGP database. Syntax show ip bgp paths as-path Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810.
PAGE 1154
Version 7.4.1.0 Introduced on the E-Series TeraScale. show ip bgp paths extcommunity View all unique extended community information in the BGP database. Syntax show ip bgp paths extcommunity Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.
PAGE 1155
• ? = (question mark) sequences in a pattern (either 0 or 1 sequences). NOTE: You must enter an escape sequence (CTRL+v) prior to entering the ? regular expression. • [ ] = (brackets) a range of single-character patterns. • ^ = (caret) the beginning of the input string. If the caret is used at the beginning of a sequence or range, it matches on everything BUT the characters specified. • $ = (dollar sign) the end of the output string.
PAGE 1156
Defaults • keepalive = 60 seconds • holdtimer = 180 seconds Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 8.2.1.
PAGE 1157
Defaults IPv6 Unicast Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1158
summary-only (OPTIONAL) Enter the keywords summary-only to advertise only the aggregate address. Specific routes are not advertised. suppress-map map-name (OPTIONAL) Enter the keywords suppress-map then the name of a configured route map to identify which morespecific routes in the aggregate are suppressed. Defaults Not configured. Command Modes ROUTER-BGPV6-ADDRESS FAMILY Command History This guide is platform-specific.
PAGE 1159
bgp dampening Enable BGP route dampening and configure the dampening parameters. Syntax Parameters bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] half-life (OPTIONAL) Enter the number of minutes after which the Penalty is decreased. After the router assigns a Penalty of 1024 to a route, the Penalty is decreased by half, after the half-life period expires. The range is from 1 to 45. The default is 15 minutes.
PAGE 1160
Usage Information If you enter bgp dampening, the default values for half-life, reuse, suppress, and max-suppress-time are applied. The parameters are positiondependent; therefore, if you configure one parameter, you must configure the parameters in the order they appear in the command. Related Commands show ip bgp ipv6 unicast dampened-paths – views the BGP paths. clear ip bgp ipv6 unicast Reset MBGP sessions.
PAGE 1161
clear ip bgp ipv6 unicast dampening Clear information on route dampening. Syntax Parameters clear ip bgp dampening ipv6 unicast [network network-mask] network (OPTIONAL) Enter the IPv6 network address in x:x:x:x::x format. network-mask If you enter the network address, next enter the network mask, from 0 to 128. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1162
Command Modes Command History • * (asterisk) matches on sequences in a pattern (zero or more sequences). • + (plus sign) matches on sequences in a pattern (one or more sequences). • ? (question mark) matches sequences in a pattern (0 or 1 sequences). • [ ] (brackets) matches a range of single-character patterns. • ^ (caret) matches the beginning of the input string. (If the caret is used at the beginning of a sequence or range, it matches on everything BUT the characters specified.
PAGE 1163
Version 7.4.1.0 Introduced on the E-Series TeraScale. debug ip bgp ipv6 unicast peer-group updates View information about BGP peer-group updates. Syntax debug ip bgp ipv6 unicast peer-group peer-group-name updates [in | out] To disable debugging, use the no debug ip bgp ipv6 unicast peer-group peer-group-name updates [in | out] command. Parameters peer-group peer-groupname Enter the keywords peer-group then the name of the peergroup. updates Enter the keyword updates to view BGP update information.
PAGE 1164
debug ip bgp ipv6 unicast updates View information about BGP updates. Syntax Parameters debug ip bgp ipv6 unicast ipv6-address prefix-length updates [in | out] ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. updates Enter the keyword updates to view BGP update information.
PAGE 1165
Parameters Defaults externaldistance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internaldistance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200. local-distance Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255. The default is 200.
PAGE 1166
neighbor activate Allows you to enable a specified neighbor/peer group for the current address and subsequent address family identifier (AFI/SAFI). Syntax neighbor [ipv6-address | peer-group-name] activate To disable, use the no neighbor [ipv6-address | peer-group-name] activate command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Identify a peer group by name.
PAGE 1167
neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. Syntax neighbor {ipv6-address | peer-group-name} advertisementinterval seconds To return to the default value, use the no neighbor {ipv6-address | peergroup-name} advertisement-interval command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1168
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ipv6-address | peer-group-name} default-originate [route-map map-name] To remove a default route, use the no neighbor {ipv6-address | peergroup-name} default-originate command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1169
To delete a neighbor distribution list, use the no neighbor {ipv6-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. prefix-listname Enter the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes).
PAGE 1170
To delete a BGP filter, use the no neighbor [ipv6-address | peer-groupname] filter-list aspath access-list-name [in | out] command. Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group to apply the filter to all routers in the peer group. access-listname Enter the name of an established AS-PATH access list.
PAGE 1171
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname Enter the name of the peer group. maximum Enter a number as the maximum number of prefixes allowed for this BGP router. The range is from 1 to 4294967295. threshold (OPTIONAL) Enter a number to be used as a percentage of the maximum value. When the number of prefixes reaches this percentage of the maximum value, the software sends a message.
PAGE 1172
Parameters ipv6-address Enter the IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. peer-groupname (OPTIONAL) Enter the name of the peer group. Defaults Disabled. Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1173
Command Modes ROUTER BGPV6-ADDRESS FAMILY Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1174
Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale. When you apply a route map to outbound routes, only routes that match at least one section of the route map are permitted. If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used in this command.
PAGE 1175
Usage Information Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale. The first time you enter this command it configures the neighbor as a route reflector and members of the route-reflector cluster. Internal BGP (IBGP) speakers do not need to be fully meshed if you configure a route reflector. When all clients of a route reflector are disabled, the neighbor is no longer a route reflector.
PAGE 1176
Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale. Usage Information The software resolves the network address configured by the network command with the routes in the main routing table to ensure that the networks are reachable using non-BGP routes and non-default routes. Related Commands redistribute – redistributes routes into BGP. redistribute Redistribute routes into BGP.
PAGE 1177
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1178
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. show ip bgp ipv6 unicast View the current MBGP route table. C-Series, E-Series, S4810 Syntax Paramters Command Modes Command History Usage Information 1178 show ip bgp ipv6 unicast [network [network-mask] [length]] network (OPTIONAL) Enter the network address (in dotted decimal format) of the BGP network to view information only on that network.
PAGE 1179
Example Dell#show ip bgp ipv6 unicast BGP table version is 8, local router ID is 5.5.10.
PAGE 1180
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1181
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1182
show ip bgp ipv6 unicast dampened-paths View BGP routes that are dampened (non-active). Syntax show ip bgp ipv6 unicast dampened-paths Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.
PAGE 1183
bgpNdP 0x41a17000 : NdTmrP 0x41a17000 : NdKATmrP 0x41a17014 : NdTics 327741 : NhLocAS 1 : NdState 2 : NdRPMPrim 1 : NdListSoc 13 NdAuto 1 : NdEqCost 1 : NdSync 0 : NdDefOrg 0 NdV6ListSoc 14 NdDefDid 0 : NdConfedId 0 : NdMedConfed 0 : NdMedMissVal -1 : NdIgnrIllId 0 : NdRRC2C 1 : NdClstId 33686273 : NdPaTblP 0x41a19088 NdASPTblP 0x41a19090 : NdCommTblP 0x41a19098 : NhOptTransTblP 0x41a190a0 : NdRRClsTblP 0x41a190a8 NdPktPA 0 : NdLocCBP 0x41a6f000 : NdTmpPAP 0x419efc80 : NdTmpASPAP 0x41a25000 : NdTmpCommP 0x4
PAGE 1184
show ip bgp ipv6 unicast flap-statistics View flap statistics on BGP routes. Syntax Parameters show ip bgp ipv6 unicast flap-statistics [ipv6-address prefixlength] [filter-list as-path-name] [regexp regular-expression] ipv6-address prefix-length Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1185
Version 7.4.1.0 Example Introduced on the E-Series TeraScale. Dell#show ip bgp ipv6 unicast flap-statistics BGP table version is 8, local router ID is 5.5.10.
PAGE 1186
show ip bgp ipv6 unicast neighbors Allows you to view the information exchanged by BGP neighbors. Syntax Parameters show ip bgp ipv6 unicast neighbors [ipv6-address prefix-length [advertised-routes | dampened-routes | detail | flap-statistics | routes]] ipv6-address prefix-length (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros.
PAGE 1187
Lines Beginning With Description BGP neighbor Displays the BGP neighbor address and its AS number. The last phrase in the line indicates whether the link between the BGP router and its neighbor is an external or internal one. If they are located in the same AS, then the link is internal; otherwise, the link is external. BGP version Displays the BGP version (always version 4) and the remote router ID.
PAGE 1188
Example Lines Beginning With Description Connections established Displays the number of TCP connections established and dropped between the two peers to exchange BGP information. Last reset Displays the amount of time since the peering session was last reset. Also states if the peer resets the peering session. If the peering session was never reset, the word “never” is displayed. Local host: Displays the peering address of the local router and the TCP port number.
PAGE 1189
BGP neighbor is 5ffe:11::3, remote AS 1, external link BGP version 4, remote router ID 5.5.5.
PAGE 1190
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version 8.3.19.0 Introduced on the S4820T. Version 8.4.2.1 Introduced on the C-Series and S4810. Version 7.4.1.0 Introduced on the E-Series TeraScale.
PAGE 1191
Field Description BGP router identifier Displays the local router ID and the AS number. BGP table version Displays the BGP table version and the main routing table version. network entries Displays the number of network entries, route paths, and the amount of memory used to process those entries. BGP path attribute entries Displays the number of BGP path attributes and the amount of memory used to process them.
PAGE 1192
Field Description If a maximum limit was configured with the neighbor maximum-prefix command, (prfxd) appears in this column. If the neighbor is not in Established stage, the current stage is displayed (Idle, Connect, Active, OpenSent, OpenConfirm). When the peer is transitioning between states and clearing the routes received, the phrase (Purging) may appear in this column. If the neighbor is disabled, the phrase (Admin shut) appears in this column.
PAGE 1193
iSCSI Optimization 33 Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on an system. To configure and verify the iSCSI optimization feature, use the following Dell Networking OS commands. advertise dcbx-app-tlv Configure DCBX to send iSCSI TLV advertisements. Syntax advertise dcbx-app-tlv iscsi To disable DCBX iSCSI TLV advertisements, use the no advertise dcbx-apptlv iscsi command. Defaults Disabled.
PAGE 1194
iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes. Defaults 10 minutes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1195
disable Enter the keyword disable to disable the application of preferential QoS treatment to iSCSI frames. dot1p vlanpriority-value Enter the dot1p value of the VLAN priority tag assigned to the incoming packets in an iSCSI session. The range is from 0 to 7. The default is the dot1p value in ingress iSCSI frames is not changed and is the same priority is used in iSCSI TLV advertisements if you did not enter the iscsi prioritybits command.
PAGE 1196
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module.
PAGE 1197
iscsi profile-compellant Configure the auto-detection of Dell Compellent arrays on a port. Syntax iscsi profile-compellent Defaults Dell Compellent disk arrays are not detected. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 8.3.19.
PAGE 1198
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module.
PAGE 1199
-----------------------------------------------iSCSI Targets and TCP Ports: -----------------------------------------------TCP Port Target IP Address 3260 860 Related Commands • show iscsi session — displays information about active iSCSI sessions on the switch. • show iscsi session detailed — displays detailed information about active iSCSI sessions on the switch. • show run iscsi — shows run iscsi. show iscsi session Display information about active iSCSI sessions on the switch.
PAGE 1200
Usage Information Only sessions the switch observes are learned; sessions flowing through an adjacent switch are not learned. After the switch is reloaded, any information exchanged during the initial handshake is not available. If the switch picks up the communication after reloading, it would detect a session was in progress but could not obtain complete information for it. Any incomplete information of this type would not be available in the show commands.
PAGE 1201
Session 1 : ---------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-35 Up Time:00:00:01:22(DD:HH:MM:SS) Time for aging out:00:00:09:31(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.53 33432 10.10.0.101 3260 0 Related Commands • show iscsi — displays the currently configured iSCSI settings.
PAGE 1202
Intermediate System to Intermediate System (IS-IS) 34 The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the platform. IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing both IP and OSI traffic. A router is considered an intermediate system. Networks are partitioned into manageable routing domains, called areas.
PAGE 1203
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabled by default.
PAGE 1204
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support.
PAGE 1205
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 1206
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. Usage Information CAUTION: Use caution when you enter this command. Back up your configuration prior to using this command or your IS-IS configuration will be erased. clear isis Restart the IS-IS process. All IS-IS data is cleared.
PAGE 1207
Version Description 8.3.11.1 Introduced on the Z9000. clns host Define a name-to-network service mapping point (NSAP) that you use with commands that require NSAPs and system IDs. Syntax Parameters clns host name nsap name Enter an alphanumeric string to identify the name-to-NSAP mapping. nsap Enter a specific NSAP address that is associated with the name parameter. Defaults Not configured. Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 1208
debug isis Enable debugging for all IS-IS operations. Syntax debug isis To disable debugging of IS-IS, use the no debug isis command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1209
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1210
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1211
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1212
trigger detail tied to the VRF that you specify. When SPF is triggered, this debugging information is displayed. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms,refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 1213
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(0.2) Introduced on the Z9000. 9.0.2.
PAGE 1214
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support.
PAGE 1215
Parameters description Defaults none Command Modes ROUTER ISIS Command History Related Commands Enter a description to identify the IS-IS protocol (80 characters maximum). Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. pre-7.7.1.0 Introduced. router isis — Enter ROUTER mode on the switch.
PAGE 1216
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. The administrative distance indicates the trust value of incoming packets. A low administrative distance indicates a high trust rate. A high value indicates a lower trust rate.
PAGE 1217
Command Modes Command History • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 1218
static (OPTIONAL) Enter the keyword static for user-configured routing process. Defaults Not configured. Command Modes • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1219
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added IPv6 ISIS support.
PAGE 1220
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. Usage Information The domain password is inserted in Level 2 link state PDUs (LSPs), complete sequence number PDUs (CSNPs), and partial sequence number PDUs (PSNPs). Related Commands • area-password — configures an IS-IS area authentication password.
PAGE 1221
Usage Information Every graceful restart enabled router’s HELLO PDUs includes a restart TLV. This restart enables (re)starting as well as the existing ISIS peers to detect the GR capability of the routers on the connected network. A flag in the Restart TLV contains restart request (RR), restart acknowledge (RA) and suppress adjacency advertisement (SA) bit flags. The ISIS graceful restart-enabled router can co-exist in mixed topologies where some routers are graceful restart-enabled and others are not.
PAGE 1222
graceful-restart t1 Set the graceful restart wait time before unacknowledged restart requests are generated. This wait time is the interval before the system sends a restart request (an IIH with RR bit set in Restart TLV) until the CSNP is received from the helping router. Syntax graceful-restart t1 {interval seconds | retry-times value} To return to the default, use the no graceful-restart t1 command. Parameters interval Enter the keyword interval to set the wait time.
PAGE 1223
Parameters level-1, level-2 Enter the keywords level-1 or level-2 to identify the database instance type to which the wait interval applies. seconds Enter the gracefule-restart t2 time in seconds. The range is from 5 to 120 seconds. The default is 30 seconds. Defaults 30 seconds Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1224
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 1225
Defaults 30 seconds Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 1226
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information IS-IS hellos are padded to the full maximum transmission unit (MTU) size. Padding IS-IS Hellos (IIHS) to the full MTU provides early error detection of large frame transmission problems or mismatched MTUs on adjacent interfaces.
PAGE 1227
ignore-lsp-errors Ignore LSPs with bad checksums instead of purging those LSPs. Syntax ignore-lsp-errors To return to the default values, use the no ignore-lsp-errors command. Defaults In IS-IS, the default deletes LSPs with internal checksum errors (no ignore-lsperrors). Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1228
Defaults No processes are configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.
PAGE 1229
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.
PAGE 1230
level-2-only You can form a Level 2 adjacencies when other Level 2 or Level 1-2 routers and their interfaces are configured for Level 1-2 or Level 2. Level 1 adjacencies cannot be established on this interface. Defaults level-1-2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1231
level-2 (OPTIONAL) Independently configures the interval of time between transmission of CSNPs for Level 2. Defaults seconds = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.
PAGE 1232
Defaults seconds = 10; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.
PAGE 1233
Defaults multiplier = 3; level-1 (if not otherwise specified) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1234
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Usage Information Hello PDUs are “padded” only when both the global and interface padding options are ON. Turning either one OFF disables padding for the corresponding interface. Related Commands hello padding — turns ON or OFF padding for LAN and point-to-point hello PDUs. isis ipv6 metric Assign metric to an interface for use with IPv6 information.
PAGE 1235
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis metric Assign a metric to an interface.
PAGE 1236
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 1237
isis password Configure an authentication password for an interface. Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [password] [level-1 | level-2] command. Parameters encryptiontype (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password.
PAGE 1238
This password provides limited security as it is processed as plain text. isis priority Set the priority of the designated router you select. Syntax isis priority value [level-1 | level-2] To return to the default values, use the no isis priority [value] [level-1 | level-2] command. Parameters value This value sets the router priority. The higher the value, the higher the priority. The range is from 0 to 127. The default is 64. level-1 (OPTIONAL) Specify the priority for Level 1.
PAGE 1239
Setting the priority to 0 lowers the chance of this system becoming the DIS, but does not prevent it. If all the routers have priority 0, one with highest MAC address becomes DIS even though its priority is 0. is-type Configure IS-IS operating level for a router. Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters level-1 Allows a router to act as a Level 1 router.
PAGE 1240
log-adjacency-changes Generate a log messages for adjacency state changes. Syntax log-adjacency-changes To disable this function, use the no log-adjacency-changes command. Defaults Adjacency changes are not logged. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1241
interval seconds Enter the maximum number of seconds between LSP generations. The range is from 0 to 120 seconds. The default is 5 seconds. initial_wait_inte rval seconds (OPTIONAL) Enter the initial wait time, in seconds, before running the first LSP generation. The range is from 0 to 120 seconds. The default is 1 second. second_wait_i nterval seconds (OPTIONAL) Enter the wait interval, in seconds, between the first and second LSP generation. The range is from 0 to 120 seconds.
PAGE 1242
lsp-mtu Set the maximum transmission unit (MTU) of IS-IS link-state packets (LSPs). This command only limits the size of LSPs this router generates. Syntax lsp-mtu size To return to the default values, use the no lsp-mtu command. Parameters size The maximum LSP size, in bytes. The range is from 512 to 16000 for Non-Jumbo mode and from 128 to 9195 for Jumbo mode. The default is 1497. NOTE: The appropriate interface circuit is brought down and removed. Defaults 1497 bytes.
PAGE 1243
lsp-refresh-interval Set the link state PDU (LSP) refresh interval. LSPs must be refreshed before they expire. When the LSPs are not refreshed after a refresh interval, they are kept in a database until their max-lsp-lifetime reaches zero and then LSPs is purged. Syntax lsp-refresh-interval seconds To restore the default refresh interval, use the no lsp-refresh-interval command. Parameters seconds The LSP refresh interval, in seconds.
PAGE 1244
max-area-addresses Configure manual area addresses. Syntax max-area-addresses number To return to the default values, use the no max-area-addresses command. Parameters number Set the maximum number of manual area addresses. The range is from 3 to 6. The default is 3. Defaults 3 addresses Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1245
Defaults 1200 seconds Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.
PAGE 1246
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added support for multi-topology ISIS. 6.3.1.
PAGE 1247
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
PAGE 1248
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Introduced. net To configure an IS-IS network entity title (NET) for a routing process, use this mandatory command. If you did not configure a NET, the IS-IS process does not start. Syntax net network-entity-title To remove a net, use the no net network-entity-title command.
PAGE 1249
passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface. Syntax passive-interface interface To delete a passive interface configuration, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1250
redistribute Redistribute routes from one routing domain to another routing domain. Syntax redistribute {static | connected | rip} [level-1 | level-1-2 | level-2] [metric metric-value] [metric-type {external | internal}] [route-map map-name] To end redistribution or disable any of the specified keywords, use the no redistribute {static | connected | rip} [metric metric-value] [metric-type {external | internal}] [level-1 | level-1-2 | level-2] [route-map map-name] command.
PAGE 1251
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.
PAGE 1252
redistribute bgp Redistribute routing information from a BGP process. Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value] [metric-type {external| internal}] [route-map map-name] To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter a number that corresponds to the autonomous system number. The range is from 1 to 65355.
PAGE 1253
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. Usage Information BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command.
PAGE 1254
metric-type {external | internal} (OPTIONAL) The external link type associated with the default route advertised into a routing domain. The two options are: • external • internal level-1 (OPTIONAL) Routes are independently redistributed into ISIS as Level 1 routes. level-1-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level-1-2 routes. level-2 (OPTIONAL) Routes are independently redistributed into ISIS as Level 2 routes. This setting is the default.
PAGE 1255
Usage Information Version Description 6.3.1.0 Introduced. How a metric value assigned to a redistributed route is advertised depends on how on the configuration of the metric-style command. If the metric-style command is set for Narrow mode and the metric value in the redistribute ospf command is set to a number higher than 63, the metric value advertised in LSPs is 63. If the metric-style command is set for wide mode, the metric value in the redistribute ospf command is advertised.
PAGE 1256
Usage Information Configure a network entity title (the net command) to specify the area address and the router system ID. Enable routing on one or more interfaces to establish adjacencies and establish dynamic routing. You can configure only one IS-IS routing process to perform Level 2 routing. A level-1-2 designation performs Level 1 and Level 2 routing at the same time.
PAGE 1257
Usage Information Version Description 6.3.1.0 Introduced. Set the overload bit when a router experiences problems, such as a memory shortage due to an incomplete link state database which can result in an incomplete or inaccurate routing table. If you set the overload bit in its LSPs, other routers ignore the unreliable router in their SPF calculations until the router has recovered. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 address.
PAGE 1258
spf-interval level-2 120 20 25 exit-address-family Example (AddressFamily_IPv6) The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode. Dell(conf-router_isis-af_ipv6)#show conf ! address-family ipv6 unicast maximum-paths 16 multi-topology transition set-overload-bit spf-interval level-1 100 15 20 spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database.
PAGE 1259
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added supported for VRF. Introduced on the S6000-ON. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810.
PAGE 1260
Field Description value between brackets indicates the duration that the purged LSP stays in the database before being removed. Example ATT This value represents the Attach bit. This value indicates that the router is a Level 2 router and can reach other areas. Level 1-only routers and Level 1-2 routers that have lost connection to other Level 2 routers use the Attach bit to find the closest Level 2 router. They point a default route to the closest Level 2 router. P This value represents the P bit.
PAGE 1261
Metric: 10 IP 10.1.1.0 255.255.255.0 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 20 IP 10.3.3.0 255.255.255.0 Metric: 10 IPv6 (MT-IPv6) 1011::/64 Metric: 10 IPv6 (MT-IPv6) 1511::/64 Metric: 10 IPv6 (MT-IPv6) 2511::/64 Metric: 20 IPv6 (MT-IPv6) 1033::/64 Metric: 10 IPv6 2511::/64 Metric: 20 IPv6 1033::/64 Hostname: ISIS FTOS#show isis database detail IS-IS Level-1 Link State Database LSPID LSP Seq Num Holdtime ATT/P/OL FTOS.00-00 * 0x00000009 941 1/0/0 NLPID: 0xCC Area Address: 49.0000.
PAGE 1262
Example Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 1263
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Dell#show isis hostname System Id Dynamic Name Static Name *F100.E120.0013 Force10 ISIS Dell# show isis interface Display detailed IS-IS interface status and configuration information.
PAGE 1264
Example Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Dell>show isis int TenGigabitEthernet 1/7 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 37847070, Local circuit ID 1 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 1265
level-2 (OPTIONAL) Displays information about Level 2 IS-IS neighbors. detail (OPTIONAL) Displays detailed information about neighbors. interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1266
Example Field Description Type This value displays the adjacency type (Layer 2, Layer 2 or both). Priority IS-IS priority the neighbor advertises. The neighbor with highest priority becomes the designated router for the interface. Uptime Displays the interfaces uptime. Circuit Id The neighbor’s interpretation of the designated router for the interface. The bold sections below identify that Multi-Topology IS-IS is enabled. This command displays only one IP address per line.
PAGE 1267
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(0.2) Introduced on the Z9000. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The bold section identifies that Multi-Topology IS-IS is enabled. Dell#show isis protocol IS-IS Router: System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.
PAGE 1268
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1269
Example Item Description Level-1/Level-2 DR Elections Displays the number of times designated router elections ran. Level-1/Level-2 SPF Calculations Displays the number of shortest path first calculations. LSP checksum errors received Displays the number of checksum errors LSPs received. LSP authentication failures Displays the number of LSP authentication failures.
PAGE 1270
interval seconds Enter the maximum number of seconds between SPF calculations. The range is from 0 to 120 seconds. The default is 10 seconds. initial_wait_inte rval seconds (OPTIONAL) Enter the initial wait time, in seconds, before running the first SPF calculations. The range is from 0 to 120 seconds. The default is 5 seconds. second_wait_i nterval seconds (OPTIONAL) Enter the wait interval, in seconds, between the first and second SPF calculations. The range is from 0 to 120 seconds.
PAGE 1271
are no triggers for two times the maximum interval, fast behavior is restored (the initial wait time).
PAGE 1272
35 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. The LACP commands in this chapter are supported by Dell Networking OS on the platform. NOTE: For static LAG commands, refer to Port Channel Commands in the Interfaces chapter), based on the standards specified in the IEEE 802.
PAGE 1273
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command.
PAGE 1274
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.
PAGE 1275
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command applies to dynamic port-channel interfaces only. When applied on a static port-channel, this command has no effect. Related Commands show lacp — displays the LACP configuration.
PAGE 1276
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp system-priority Configure the LACP system priority. Syntax Parameters lacp system-priority priority-value priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. Defaults 32768 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1277
port-channel mode Configure the LACP port channel mode. Syntax Parameters port-channel number mode [active] [passive] [off] number Enter the keywords number then a number. The range is from 1 to 128. active Enter the keyword active to set the mode to the active state. NOTE: LACP modes are defined in Usage Information. passive Enter the keyword passive to set the mode to the passive state. NOTE: LACP modes are defined in Usage Information. off Enter the keyword off to set the mode to the off state.
PAGE 1278
Mode Function passive An interface is not in an active negotiating state in this mode. LACP runs on any link configured in the passive state. Ports in a passive state respond to negotiation requests from other ports that are in active states. Ports in a passive state respond to LACP packets off An interface cannot be part of a dynamic port channel in off mode. LACP does not run on a port configured in off mode. port-channel-protocol lacp Enable LACP on any LAN port.
PAGE 1279
show lacp Display the LACP matrix. S5000 Syntax Parameters show lacp port-channel-number [sys-id | counters] port-channelnumber Enter a port-channel number. The range is from 1 to 128. sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters. Defaults Without a Port Channel specified, the command clears all Port Channel counters.
PAGE 1280
enabled L-Distribution disabled, M-Partner Defaulted, N-Partner Non-defaulted, O-Receiver is in expired state, P-Receiver is not in expired state Port Te 1/6 is enabled, LACP is Actor Admin: State ACEHJLMP Oper: State ACEGIKNP Partner Admin: State BDFHJLMP Oper: State BCEGIKNP Dell# Example (Sysid) enabled and mode is lacp Key 1 Priority 128 Key 1 Priority 128 Key 0 Priority 0 Key 1 Priority 128 Dell#show lacp 1 sys-id Actor System ID: Priority 32768, Address 0001.e800.
PAGE 1281
36 Layer 2 This chapter describes commands to configure Layer 2 features. This chapter contains the following sections: • MAC Addressing Commands • Virtual LAN (VLAN) Commands • Far-End Failure Detection (FEFD) The VLAN commands are supported on all the platform. MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table.
PAGE 1282
vlan vlan-id Command Modes Command History • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Enter the keyword vlan followed by a VLAN ID number from 1 to 4094. EXEC Privilege Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.12.0 Added support for sticky MAC addresses. 8.5.1.
PAGE 1283
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 1284
output-range interface vlan vlan-id • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. For a multicast MAC address, enter the keyword outputrange then one of the following interfaces to indicate a range of ports for which traffic is forwarded: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1285
Example (Multicast) mac-address-table static 01:00:5E:01:00:01 {multicast vlan 2 output—range Te 1/2,Te 1/3} Related Commands show mac-address-table — displays the MAC address table. mac-address-table station-move threshold Change the frequency with which the MAC address station-move trap is sent after a MAC address changes in a VLAN. A trap is sent if a station move is detected above a threshold number of times in a given interval.
PAGE 1286
mac-address-table station-move refresh-arp Ensure that address resolution protocol (ARP) refreshes the egress interface when a station move occurs due to a topology change. Syntax [no] mac-address-table station-move refresh-arp Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1287
Defaults dynamic (OPTIONAL) Enter the keyword dynamic to allow aging of MACs even though a learning limit is configured. station-moveviolation (OPTIONAL) Enter the keywords station-move to allow a station move on learned MAC addresses. • On S-Series, the default behavior is dynamic. NOTE: “Static” means manually entered addresses, which do not age. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1288
another interface. Enabling or disabling this option has no effect on already learned MAC addresses. After the MAC address learning limit is reached, the MAC addresses do not age out unless you add the dynamic option. To clear statistics on MAC address learning, use the clear counters command with the learning-limit parameter.
PAGE 1289
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands show mac learning-limit — displays details of the mac learning-limit.
PAGE 1290
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Usage Information If you configure mac-learn-limit and the sticky MAC feature is enabled, dynamically learned MAC addresses are converted to sticky for that port. Any new MAC address that is learned also becomes sticky for that port. Related Commands show mac learning-limit — displays the details of the mac learning-limit.
PAGE 1291
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs. Related Commands show mac learning-limit — displays details of the mac learning-limit.
PAGE 1292
Version Description 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. show cam mac stack-unit Display the content addressable memory (CAM) size and the portions allocated for MAC addresses and for MAC ACLs.
PAGE 1293
vlan vlan-id Command Modes Command History • EXEC • EXEC Privilege (OPTIONAL) Enter the keyword vlan followed by the VLAN ID to display the MAC address assigned to the VLAN. The range is 1 to 4094. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series.
PAGE 1294
interface interface (OPTIONAL) Enter the keyword interface then the interface type, slot/port information: • For a port channel interface, enter the keywords portchannel then a number. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1295
Column Heading Description VlanId Displays the VLAN ID number. Mac Address Displays the MAC address in nn:nn:nn:nn:nn:nn format. Type Lists whether the MAC address was manually configured (Static), learned dynamically (Dynamic), or associated with a specific port (Sticky). Interface Displays the interface type and slot/port information. The following abbreviations describe the interface types: State Example Usage Information Layer 2 • gi — Gigabit Ethernet then a slot/port.
PAGE 1296
Column Heading Description State Lists if the MAC address is in use (Active) or not in use (Inactive). The following describes the show mac-address-table count command shown in the following example. Line Beginning With Description MAC Entries... Displays the number of MAC entries learned per VLAN. Dynamic Address... Lists the number of dynamically learned MAC addresses. Static Address... Lists the number of user-defined MAC addresses. Total MAC...
PAGE 1297
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series and S-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 1298
Command Modes Command History Usage Information • EXEC • EXEC Privilege Version 9.0(1.3) Introduced on the S5000. MAC Accounting information can be accessed using SNMP via the Force10 MONITOR MIB. For more information about enabling SNMP, refer to the Dell Networking OS Configuration Guide. NOTE: Currently, the Force10 MONITOR MIB does not return the MAC addresses in an increasing order using SNMP.
PAGE 1299
• For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1300
Virtual LAN (VLAN) Commands The following commands configure and monitor virtual LANs (VLANs). VLANs are a virtual interface and use many of the same commands as physical interfaces. You can configure an IP address and Layer 3 protocols on a VLAN called Inter-VLAN routing. FTP, TFTP, ACLs and SNMP are not supported on a VLAN. Occasionally, while sending broadcast traffic over multiple Layer 3 VLANs, the VRRP state of a VLAN interface may continually switch between Master and Backup.
PAGE 1301
default vlan-id Specify a VLAN as the Default VLAN. Syntax default vlan-id vlan-id To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Defaults The Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1302
default-vlan disable Disable the default VLAN so that all switchports are placed in the Null VLAN until they are explicitly configured as a member of another VLAN. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.
PAGE 1303
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1304
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Dell(conf-if-vl-100)#show config ! interface Vlan 100 no ip address no shutdown Dell(conf-if-vl-100)# show vlan Display the current VLAN configurations on the switch.
PAGE 1305
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Updated to support OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Augmented to display PVLAN data for the C-Series and SSeries and revised the output to include the Description field to display a user-entered VLAN description. 7.6.1.
PAGE 1306
Column Heading Ports Example Description • v (not capitalized v) for VLT untagged • V (capitalized V) for VLT tagged Displays the type, slot, and port information.
PAGE 1307
Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 41 Status Description Q Ports Active T Te 13/47 Dell#show vlan id 42 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 42 Dell# Status Description Q Ports Active U Te 13/47 Example (Brief) Dell#show vlan br VLAN Name STG MAC Aging IP Address ---- --------------------------------
PAGE 1308
tagged Add a Layer 2 interface to a VLAN as a tagged interface. S5000 Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1309
Tagged interfaces can belong to multiple VLANs, while untagged interfaces can only belong to one VLAN at a time. Related Commands interface vlan — configures a VLAN. untagged — specifies which interfaces in a VLAN are untagged. track ip Track the Layer 3 operational state of a Layer 3 VLAN, using a subset of the VLAN member interfaces. S5000 Syntax track ip interface To remove the tracking feature from the VLAN, use the no track ip interface command.
PAGE 1310
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. When this command is configured, the VLAN is operationally UP if any of the interfaces specified in the track ip command are operationally UP, and the VLAN is operationally DOWN if none of the tracking interfaces are operationally UP.
PAGE 1311
Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1312
debug fefd Enable debugging of FEFD. Syntax debug fefd {events | packets} [interface] To disable debugging of FEFD, use the no debug fefd {events | packets} [interface] command. Parameters events Enter the keyword events to enable debugging of FEFD state changes. packets Enter the keyword packets to enable debugging of FEFD to view information on packets sent and received.
PAGE 1313
fefd Enable Far-End Failure Detection on an interface, set the FEFD interval, or select the FEFD mode. Syntax Parameters fefd {disable|interval|mode {aggressive|normal} disable Enter the keyword disable to disable FEFD for the specified interface. interval Enter the keyword interval, followed by a value to specify the FEFD interval in seconds. Range is from 3 to 300. Default is 15. mode Enter the keyword mode followed by the mode type to specify the FEFD mode.
PAGE 1314
Related Commands • fefd disable — disables far-end failure detection on an interface. • fefd reset — enables FEFD globally on the system. • fefd mode — changes FEFD mode on an interface. fefd disable Disable FEFD on an interface only. This command overrides the fefd reset command for the interface. Syntax fefd disable To re-enable FEFD on an interface, use the no fefd disable command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1315
fefd-global Enable FEFD globally on the system. Syntax fefd-global [interval seconds][mode {normal | aggressive}] To disable FEFD globally, use the no fefd-global [mode {normal | aggressive}] command. Parameters interval seconds Enter the keyword interval followed by the number of seconds to wait between FEFD control packets. Range is from 3 to 300 seconds. Default is 15 seconds.
PAGE 1316
If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. Related Commands • fefd — enables far-end failure detection. • fefd-global interval — configures an interval between FEFD control packets. • show fefd — shows the FEFD command output. fefd-global interval Configure an interval between FEFD control packets. Syntax fefd-global interval seconds To return to the default value, use the no fefd-global interval command.
PAGE 1317
fefd interval Set an interval between control packets. Syntax fefd interval seconds To return to the default value, use the no fefd interval command. Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1318
Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol. aggressive (OPTIONAL) Enter the keyword aggressive to change the link state to “error-disabled” when a far-end failure the software detects on that interface.
PAGE 1319
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 1320
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Legacy E-Series command.
PAGE 1321
Te 5/6 Te 5/7 Te 5/8 Te 5/9 Te 5/10 Te 5/11 Dell# Related Commands Layer 2 Aggressive Aggressive Aggressive Aggressive NA Aggressive 10 10 10 10 NA 10 Admin Shutdown Admin Shutdown Admin Shutdown Admin Shutdown Locally disabled Err-disabled • fefd — enables far-end failure detection. • fefd disable — disables FEFD on an interface only. • fefd-global — enables FEFD globally on the system. • fefd reset — resets all interfaces or a single interface that was in “error-disabled” mode.
PAGE 1322
Link Layer Discovery Protocol (LLDP) 37 The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. This chapter contains the following sections: • LLPD Commands • LLDP-MED Commands LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management.
PAGE 1323
port-vlan-id Enter the keywords port-vlan-id to advertise the port VLAN identification TLV. vlan-name Enter the keywords vlan-name to advertise the vlan-name TLV. This keyword is only supported on the C-Series and SSeries. Defaults Disabled. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1324
Defaults none Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1325
Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.1.(0.0) Modified to support management-address parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1326
Command Modes INTERFACE (conf-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.1.(0.0) Introduced on the Z9000 and S4810. 8.3.19.0 Introduced on the S4820T.
PAGE 1327
Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. clear lldp neighbors Clear LLDP neighbor information for all interfaces or a specific interface. Syntax Parameters clear lldp neighbors {interface} interface Defaults none Command Modes EXEC Privilege Command History Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1328
debug lldp interface To display timer events, neighbor additions or deletions, and other information about incoming and outgoing packets, enable LLDP debugging. Syntax debug lldp interface {interface | all}{events | packet {brief | detail} {tx | rx | both}} To disable debugging, use the no debug lldp interface {interface | all}{events} {packet {brief | detail} {tx | rx | both}} command.
PAGE 1329
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. disable Enable or disable LLDP. Syntax disable To enable LLDP, use the no disable command.
PAGE 1330
Related Commands protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. hello Configure the rate at which the LLDP control packets are sent to its peer. Syntax hello seconds To revert to the default, use the no hello seconds command. Parameters seconds Enter the rate, in seconds, at which the control packets are sent to its peer. The rate is from 5 to 180 seconds. The default is 30 seconds.
PAGE 1331
management-interface Enable and configure LLDP protocol parameters on the management interface. Syntax management-interface To remove LLDP configuration on a management interface, use the no management-interface command. Command Modes LLDP (conf-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1332
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) — enables LLDP globally. show lldp neighbors — displays the LLDP neighbors.
PAGE 1333
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch. Syntax protocol lldp To disable LLDP globally on the chassis, use the no protocol lldp command. Defaults Enabled. Command Modes CONFIGURATION (conf-lldp) Command History This guide is platform-specific.
PAGE 1334
Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1335
detail (OPTIONAL) Enter the keyword detail to display all the TLV information, remote management IP addresses, timers, and LLDP tx and rx counters. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.
PAGE 1336
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.
PAGE 1337
show running-config lldp Display the current global LLDP configuration. Syntax show running-config lldp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 1338
The E-Series generally supports the commands. However, LLDP-MED commands are more useful on the C-Series and the S50V model of the S-Series, because they support Power over Ethernet (PoE) devices. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information.
PAGE 1339
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. protocol lldp (Configuration) — enables LLDP globally. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1340
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med location-identification To advertise a location identifier, configure the system.
PAGE 1341
Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 1342
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med softphone-voice To advertise softphone to enable IP telephony on a computer so that the computer can be used as a phone, configure the system.
PAGE 1343
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med streaming-video To advertise streaming video services for broadcast or multicast-based video, configure the system.
PAGE 1344
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1345
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1346
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1347
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1348
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 1349
Microsoft Network Load Balancing 38 Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 1350
Command History Version 9.3(0.0) Added support for association of an IP address with multicast MAC address on the S4810, S4820T, S6000, and Z9000 platforms. Usage Information For multicast mode of NLB, to associate an IP address with a multicast MAC address in the switch, use address resolution protocol (ARP) by entering the arp ip-address multicast-mac-address command in Global configuration mode.
PAGE 1351
output-range interface vlan vlan-id For a multicast MAC address, enter the keyword outputrange then one of the following interfaces to indicate a range of ports for which traffic is forwarded: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number.
PAGE 1352
Multicast Source Discovery Protocol (MSDP) 39 Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell Networking operating system supports MSDP commands on the platform.
PAGE 1353
Version Description 6.2.1.1 Introduced clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 1354
clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters clear ip msdp statistic peer peer-address peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer. Defaults Without any options, this command clears the entire source-active cache. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1355
Parameters event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.). pim Enter the keyword pim to debug advertisement from PIM. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1356
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.4.1.
PAGE 1357
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.0 Introduced If a list is not specified, all SA messages received from the default peer are accepted. You can enter multiple default peer commands.
PAGE 1358
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1359
ip msdp originator-id Configure the MSDP Originator ID. S5000 Syntax ip msdp originator-id {interface} To remove the originator-id, use the no ip msdp originator-id {interface} command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1360
ip msdp peer Configure an MSDP peer. S5000 Syntax ip msdp peer peer address [connect-source] [description] [salimit number] To remove the MSDP peer, use the no ip msdp peer peer address [connect-source interface] [description name] [sa-limit number] command. Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.).
PAGE 1361
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 7.5.1.0 Added option for SA upper limit and the description option. 6.2.1.1 Introduced The connect-source option is used to supply a source IP address for the TCP connection. When an interface is specified using the connect-source option, the primary configured address on the interface is used.
PAGE 1362
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced Modifications to the ACL do not have an immediate effect on the sa-cache. To apply the redistribute filter to entries already present in the SA cache, use the clear ip msdp sa-cache local command.
PAGE 1363
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the E-Series. ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache.
PAGE 1364
limit, the subsequent SA messages are dropped (even if they pass RPF checking and policy checking). If the total number of SA messages is already larger than the limit when this command is applied, those SA messages that are already in Dell Networking OS continue to be accepted. To enforce the limit in such situation, use the clear ip msdp sa-cache command. Related Commands ip msdp peer — configures the MSDP peer. clear ip msdp peer — clears the MSDP peer. show ip msdp — displays the MSDP information.
PAGE 1365
ip multicast-msdp Enable MSDP. Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1366
Defaults Not configured. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1367
show ip msdp sa-cache rejected-sa Display the rejected SAs in the SA cache. Syntax show ip msdp sa-cache rejected-sa Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1368
40 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s. This command supports the Dell Networking platform. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol and view information on the protocol.
PAGE 1369
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1370
Command History Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. pre-7.7.1.0 Introduced protocol spanning-tree mstp – enters MULTIPLE SPANNING TREE mode on the switch. disable Globally disable the multiple spanning tree protocol on the switch. Syntax disable To enable MSTP, enter the no disable command. Defaults disabled.
PAGE 1371
Related Commands protocol spanning-tree mstp — enters MULTIPLE SPANNING TREE mode. forward-delay The amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds the interface waits in the Blocking State and the Learning State before transiting to the Forwarding State. The range is from 4 to 30.
PAGE 1372
hello-time — changes the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10. The default is 2 seconds.
PAGE 1373
max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds. Defaults 20 seconds Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific.
PAGE 1374
max-hops Configure the maximum hop count. Syntax max-hops number To return to the default values, use the no max-hops command. Parameters range Enter a number for the maximum hop count. The range is from 1 to 40. The default is 20. Defaults 20 hops Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1375
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridge-priority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
PAGE 1376
name The name you assign to the multiple spanning tree region. Syntax name region-name To remove the region name, use the no name command. Parameters region-name Enter the MST region name. The range is 32 character limit. Defaults no default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1377
protocol spanning-tree mstp To enable and configure the multiple spanning tree group, enter MULTIPLE SPANNING TREE mode. Syntax protocol spanning-tree mstp To disable the multiple spanning tree group, use the no protocol spanningtree mstp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1378
revision The revision number for the multiple spanning tree configuration. Syntax revision range To return to the default values, use the no revision command. Parameters range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. Defaults 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1379
show config View the current configuration for the mode. Only non-default values are shown. Syntax show config Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 1380
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1381
Command Modes Command History • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
PAGE 1382
Port 89 (TenGigabitEthernet 2/7) is alternate Discarding Port path cost 0, Port priority 128, Port Identifier 128.89 Designated root has priority 16384, address 0001.e800.0a:5c Designated bridge has priority 16384, address 0001.e800.0a:5c Designated port id is 128.89, designated path cost Number of transitions to forwarding state 3 BPDU (Mrecords): sent 7, received 1103 The port is not in the portfast mode Example (EDS and LBK) The bold line shows the loopback BPDU inconsistency (LBK_INC).
PAGE 1383
Usage Information Example (Guard) The following describes the show spanning-tree msti 5 guard command shown in the following example. Field Description Interface Name MSTP interface. Instance MSTP instance. Sts Port state: root-inconsistent (INCON Root), forwarding (FWD), listening (LIS), blocking (BLK), or shut down (EDS Shut). Guard Type Type of STP guard configured (Root, Loop, or BPDU guard).
PAGE 1384
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface.
PAGE 1385
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1386
rootguard Command Modes Command History Usage Information (C-, S-, and E-Series TeraScale only) Enter the keyword rootguard to enable root guard on an MSTP port or portchannel interface. INTERFACE Version Description 9.7(0.0) Introduced on the S6000-ON. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series TeraScale, C-Series, and S-Series. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.2.1.
PAGE 1387
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1388
41 Multicast The multicast commands are supported by Dell Networking operating system (OS) on all platform. This chapter contains the following sections: • IPv4 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 1389
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2.(0.0) Added support for keyword snooping on the Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 1390
mask Enter the mask in slash prefix formation ( /x ) or in dotted decimal format. null 0 (OPTIONAL) Enter the keyword null then zero (0). [protocol [process-id | tag] ip-address] (OPTIONAL) Enter one of the routing protocols: • Enter the BGP as-number then the IP address in dotted decimal format of the reverse path forwarding (RPF) neighbor. The range is from 1 to 65535. • Enter the OSPF process identification number then the IP address in dotted decimal format of the RPF neighbor.
PAGE 1391
ip multicast-limit To limit the number of multicast entries on the system, use this feature. S5000 Syntax Parameters ip multicast-limit [vrf vrf-name] limit vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to limit the number of multicast on the VRF. limit Enter the desired maximum number of multicast entries on the system. The S-Series range is from 1 to 16000. Defaults The S-Series default is 4000.
PAGE 1392
ip multicast-routing Enable IP multicast forwarding. S5000 Syntax ip multicast-routing [vrf vrf-name] To disable multicast forwarding, use the no ip multicast-routing [vrf vrf-name] command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1393
S6000-ON.] [group-address [source-address]] | summary | vlt [group-address [source-address] | count] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. static (OPTIONAL) Enter the keyword static to view static multicast routes.
PAGE 1394
Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, group-address, and source-address parameters were added on E-Series ExaScale. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1395
(50.1.1.2, 225.1.1.1), uptime 00:39:33 flags: S Incoming interface: Vlan 10 Spanned outgoing interface list: Vlan 20 (S) Usage Information Example The following describes the show ip mroute command shown in the following example. Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table.
PAGE 1396
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810.
PAGE 1397
ip multicast-limit To limit the number of multicast entries on the system, use this feature. S5000 Syntax Parameters ip multicast-limit [vrf vrf-name] limit vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to limit the number of multicast on the VRF. limit Enter the desired maximum number of multicast entries on the system. The S-Series range is from 1 to 16000. Defaults The S-Series default is 4000.
PAGE 1398
Neighbor Discovery Protocol (NDP) 42 The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 1399
interface interface To remove all neighbor entries learned on a specific interface, enter the keyword interface then the interface type and slot/port or number information of the interface: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number.
PAGE 1400
Command History Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.3.1.0 Introduced The ip nd mtu command sets the value advertised to routers. It does not set the actual MTU rate. For example, if ip nd mtu is set to 1280, the interface still passes 1500-byte packets. The mtu command sets the actual frame size passed and can be larger than the advertised MTU.
PAGE 1401
hardware_addr ess • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 1402
NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. ipv6-address Enter the IPv6 address of the neighbor in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero. interface interface Enter the keyword interface then the interface type and slot/port or number information: • For a port channel interface, enter the keywords portchannel then a number.
PAGE 1403
00:01:e8:17:5c:af REACH fe80::200:ff:fe00:17 00:00:00:00:00:29 REACH 900::1 00:01:e8:17:5c:b1 STALE 400::1 00:01:e8:17:5c:ae REACH Dell# Te 1/13 - Te 1/14 - Po 23 - Te 1/2 Vl CP 232 CP 0.60 CP 0.60 100 CP IPv6 Router Advertisement (RA) Guard The IPv6 RA guard provides support to perform conditional forwarding or blocking of the router advertisement messages that are received at the network device platform.
PAGE 1404
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. device-role Specify the role of the device attached to the port.
PAGE 1405
To reset the hop count limit, use the no hop-limit {maximum | minimum limit} command. Parameters maximum limit Enter the keyword maximum then the hop limit value. The range is from 0 to 254. minimum limit Enter the keyword minimum then the hop limit value. The range is from 0 to 254. Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
PAGE 1406
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. show ipv6 nd ra-guard policy — Displays the configuration applied on all the RA guard policies or a specific RA guard policy. ipv6 nd ra-guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command.
PAGE 1407
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. ipv6 nd ra-guard enable — Allows you to configure the RA guard related commands. managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters on Enter the keyword on to set the managed-config-flag value as ON.
PAGE 1408
To reset the access list, use the no match ra{ipv6-access-list | ipv6prefix-list | mac-access-list}command. Parameters ipv6–accesslist name Enter the keywords ipv6–access-list then the access-list name. The access-list name allows a maximum of 140 characters. ipv6–prefix-list name Enter the keywords ipv6–prefix-list then the prefix-list name. The prefix-list name allows a maximum of 140 characters. ipv6–macaccess-list name Enter the keywords ipv6–mac-access-list then the macaccess-list name.
PAGE 1409
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. • ipv6 nd ra-guard enable — Allows you to configure the RA guard related commands.
PAGE 1410
• ipv6 nd raguard policy policy-name — Defines the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. reachable-time Enable the verification of the configured reachability time in the received RA packets. Syntax reachable—time value To reset the advertised reachability time, use the no reachable-timevalue command. Parameters value Enter the advertised reachability time in milliseconds. The range is from 0 to 3,600,000 milliseconds.
PAGE 1411
Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches.
PAGE 1412
router-preference maximum Enable the verification of the advertised default router preference (DRP) value. The preference value is lower than or equal to the specified limit. If this command is not configured, the verification process is bypassed. Syntax router-preference maximum {high | low | medium} To reset the default router preference value, use the no router-preference maximum {high | low | medium} command. Parameters high Enter the keyword high to set the DRP value as high.
PAGE 1413
Example Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches.
PAGE 1414
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches.
PAGE 1415
To reset the policy applied to the trusted port, use the no trusted-port command. Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.
PAGE 1416
43 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell Networking, C-Series, E-Series, SSeries, and S4810 platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1417
Command Modes Command History Example • • EXEC EXEC Privilege Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Dell#debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface TenGigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1418
the DOWN timer is running when an interface goes down and comes back up, the DOWN timer is cancelled and the client is not notified of the event. If the timer expires and an object’s state has changed, a notification is sent to the client. If no delay is configured, a notification is sent immediately after a change in the state of a tracked object is detected. The time delay in communicating a state change is specified in seconds.
PAGE 1419
show running-config track Display the current configuration of tracked objects. Syntax Parameters Command Modes Command History Example show running-config track [object-id] object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. EXEC Privilege Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Dell#show running-config track track 1 ip route 23.0.0.
PAGE 1420
• track ip route reachability – configures object tracking on the reachability of an IPv4 route. show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1421
Output Description route ipv6address Example object is Up/ Down Up/Down state of tracked object; for example, IPv4 interface, reachability or metric threshold of an IP route. number changes, last change time Number of times that the state of the tracked object has changed and the time since the last change in hours:minutes:seconds. First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route.
PAGE 1422
2 3 Related Commands • • • • • Interface line-protocol Ethernet0/2 Interface ip routing VLAN100 Down 00:05:00 Up 01:10:05 show running-config track – displays configuration information about tracked objects. track interface ip routing – configures object tracking on the routing status of an IPv4 Layer 3 interface. track interface line-protocol – configures object tracking on the line-protocol state of a Layer 2 interface.
PAGE 1423
interface for different clients, route metrics are scaled in the range 0 to 255, where 0 is connected and 255 is inaccessible. The scaled metric value communicated to a client always considers a lower value to have priority over a higher value. The resulting scaled value is compared against the configured threshold values to determine the state of a tracked route as follows: • • If the scaled metric for a route entry is less than or equal to the UP threshold, the state of a route is UP.
PAGE 1424
Defaults none Command Modes CONFIGURATION Command History Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the routing state of an IPv4 Layer 2 interface: • The status of the IPv4 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IP address.
PAGE 1425
Defaults none Command Modes CONFIGURATION Command History Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the line-protocol state of a Layer 2 interface by monitoring its operational status (UP or DOWN).
PAGE 1426
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the UP and/or DOWN threshold of an IPv4 route metric. In order for a route’s metric to be tracked, the route must appear as an entry in the routing table. A tracked IPv4 route is considered to match an entry in the routing table only if the exact IPv4 address and prefix length match a table entry. For example, when configured as a tracked route, 10.0.0.
PAGE 1427
Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefix-len Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32. vrf vrf-name (Optional) E-Series only: You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. Defaults none Command Modes CONFIGURATION Command History Usage Information Version Description 9.7(0.
PAGE 1428
track resolution ip route Configure the protocol-specific resolution value used to scale an IPv4 route metric. Syntax track resolution ip route {isis resolution-value | ospf resolution-value} To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. isis resolutionvalue Enter the resolution used to convert the metric in the routing table for ISIS routes to a scaled metric.
PAGE 1429
Related Commands • The resolution value used to map RIP routes is not configurable. The RIP hopcount is automatically multiplied by 16 to scale it. For example, a RIP metric of 16 (unreachable) scales to 256, which considers the route to be DOWN. • threshold metric – configures the metric threshold used to determine the UP and/or DOWN state of a tracked route. • track ip route metric threshold – configures object tracking on the threshold of an IPv4 route metric.
PAGE 1430
Example Output Description Track object-id Displays the number of the tracked object. Interface type slot/port, IP route ip-address, IPv6 route ipv6address Displays the interface type and slot/port number or address of the IPv4/IPv6 route that is being tracked. object is Up/ Down Up/Down state of tracked object; for example, IPv4 interface, reachability or metric threshold of an IP route.
PAGE 1431
2 3 Related Commands IPv6 route metric threshold 2040::/64 Up 00:02:36 IPv6 route reachability 2050::/64 Up 00:02:36 • show running-config track – displays configuration information about tracked objects. • show track – displays information about tracked objects, including configuration, current state, and clients which track the object. • track interface ipv6 routing – configures object tracking on the routing status of an IPv6 Layer 3 interface.
PAGE 1432
Usage Information Related Commands Use this command to create an object that tracks the routing state of an IPv6 Layer 3 interface: • The status of the IPv6 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IP address. • The Layer 3 status of an IPv6 interface goes DOWN when its Layer 2 status goes down (for a Layer 3 VLAN, all VLAN ports must be down) or the IP address is removed from the routing table.
PAGE 1433
When you configure the threshold of an IPv6 route metric as a tracked object, the UP/DOWN state of the tracked route is also determined by the current metric for the route in the routing table. To provide a common tracking interface for different clients, route metrics are scaled in the range 0 to 255, where 0 is connected and 255 is inaccessible. The scaled metric value communicated to a client always considers a lower value to have priority over a higher value.
PAGE 1434
Usage Information Version Description 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv6 route. In order for a route’s reachability to be tracked, the route must appear as an entry in the routing table. A tracked route is considered to match an entry in the routing table only if the exact IPv6 address and prefix length match a table entry.
PAGE 1435
Command Modes Command History Usage Information CONFIGURATION Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to configure the protocol-specific resolution value that converts the actual metric of an IPv6 route in the routing table to a scaled metric in the range 0 to 255.
PAGE 1436
44 NPIV Proxy Gateway The N-port identifier virtualization (NPIV) Proxy Gateway (NPG) feature provides FCoE-FC bridging capability on the S5000 switch, allowing server CNAs to communicate with SAN fabrics over the S5000. To configure the S5000 to operate as an NPIV proxy gateway, use the following commands: dcb-map Create a DCB map to configure priority flow control (PFC) and enhanced transmission selection (ETS) on Ethernet ports that support converged Ethernet traffic.
PAGE 1437
To remove a DCB map from an interface, enter the no dcb-map map-name command in Interface configuration mode. Related Commands show qos dcb-map– displays the dcb-map profiles configured on the system. dcb-map stack-unit all stack-ports all– applies a DCB map on all ports of a switch stack. description In an FCoE map, add a text description of the FCoE and FC parameters used to transmit storage traffic over an S5000 NPIV proxy gateway in a converged fabric.
PAGE 1438
Parameters map-name Maximum: 32 alphanumeric characters. Defaults None Command Modes INTERFACE FIBRE_CHANNEL Command History Usage Information Version 9.0(1.3) Introduced on the S5000. An FCoE map is a template used to map FCoE and FC parameters in a converged fabric. An FCoE map is used to virtualize upstream FC ports on an S5000 NPIV proxy gateway so that they appear to downstream server CNA ports as FCoE forwarder (FCF) ports on an FCoE network.
PAGE 1439
fabric-id vlan In an FCoE map, configure the association between the dedicated VLAN used to carry FCoE traffic between servers and a SAN, and the fabric where the desired storage arrays are installed. S5000 Syntax Parameters fabric-id fabric-num vlan vlan-id fabric-id fabric-num Enter a fabric ID number that is the same as the ID number of the dedicated VLAN used to carry FCoE storage traffic to the fabric specified in the FCoE map.
PAGE 1440
Parameters fc-map-value Enter the unique MAC address prefix used by a SAN fabric. The range of FC-MAP values is from 0EFC00 to 0ECFF. Defaults None Command Modes FCOE MAP Command History Usage Information Version 9.0(1.3) Introduced on the S5000. The FC-MAP value you enter must match the FC-MAP value used by an FC switch or FCoE forwarder (FCF) in the fabric. An FC switch accepts only FCoE traffic that uses the correct FC-MAP value.
PAGE 1441
Command Modes Command History Usage Information FCOE MAP Version 9.0(1.3) Introduced on the S5000. The FCF priority you assign to an S5000 is used by server CNAs to select an upstream FCF to use for a fabric login (FLOGI). To remove a configured FCF priority from an FCoE map, enter the no fcfpriority command. Related Commands fcoe-map — creates an FCoE map which contains the parameters used in the communication between servers and a SAN fabric.
PAGE 1442
fka-adv-period In an FCoE map, configure the time interval used to transmit FIP keepalive (FKA) advertisements. S5000 Syntax Parameters fka-adv-period seconds seconds Defaults 8 seconds Command Modes FCOE MAP Command History Version 9.0(1.3) Enter the time period (in seconds) used to send FIP keepalive messages to peer devices. The range is from 8 to 90 seconds. Introduced on the S5000.
PAGE 1443
Command History Usage Information Version 9.0(1.3) Introduced on the S5000 configured as an NPIV proxy gateway. FCoE storage traffic received from servers on an S5000 NPIV proxy gateway is decapsulated into Fibre Channel packets and forwarded over FC links to SAN switches in a specified fabric. You must configure a separate FCoE VLAN for each fabric to which FCoE traffic is forwarded. Any non-FCoE traffic sent on a dedicated FCoE VLAN will be dropped.
PAGE 1444
Usage Information FIP keepalive (FKA) messaging is used to detect if other FCoE devices are reachable. To remove FIP keepalive monitoring from an FCoE map, enter the no keepalive command. Related Commands fcoe-map — creates an FCoE map which contains the parameters used in the communication between servers and a SAN fabric. show fcoe-map— displays the Fibre Channel and FCoE configuration parameters in FCoE maps. priority-pgid Assign 802.1p priority traffic to a priority group in a DCB map.
PAGE 1445
Command History Usage Information Version 9.0(1.3) Introduced on the S5000. PFC and ETS settings are not pre-configured on Ethernet ports. You must use the dcb-map command to configure different groups of 802.1p priorities with PFC and ETS settings. Using the priority-pgid command, you assign each 802.1p priority to one priority group. A priority group consists of 802.
PAGE 1446
strict-priority Configure the priority-group traffic to be handled with strict priority scheduling. Strict-priority traffic is serviced first, before bandwidth allocated to other priority groups is made available. pfc {on | off} Configure whether priority-based flow control is enabled (on) or disabled (off) for port traffic in the priority group. Defaults None Command Modes DCB MAP Command History Usage Information Version 9.0(1.3) Introduced on the S5000.
PAGE 1447
show fcoe-map Display the Fibre Channel and FCoE configuration parameters in FCoE maps. S5000 Syntax Parameters Command Modes Command History Usage Information show fcoe-map [brief | map-name] brief Displays an overview of currently configured FCoE maps. map-name Displays the FC and FCoE configuration parameters in a specified FCoE map. The FCoE map is applied on Ethernet (FCoE) and FC ports to transmit FC storage traffic to a specified fabric. • EXEC • EXEC Privilege Version 9.1(1.
PAGE 1448
Example Field Description VLAN priority FCoE traffic uses VLAN priority 3. (This setting is not userconfigurable.) FC-MAP FCoE MAC address-prefix value - The unique 24-bit MAC address prefix that identifies a fabric. FKA-ADV-period Time interval (in seconds) used to transmit FIP keepalive advertisements. FCF Priority The priority used by a server to select an upstream FCoE forwarder.
PAGE 1449
======================================================= Switch Zoning Parameters ======================================================= Default Zone Mode: Deny Active Zoneset: None ======================================================= Members Fc 0/0 Fc 0/1 Fc 0/2 Fc 0/3 Fc 0/4 Fc 0/5 Fc 0/6 Fc 0/7 Fc 0/8 Fc 0/9 Fc 0/10 Fc 0/11 ======================================================= ======================================================= Dell# Related Commands fcoe-map — creates an FCoE map which contain
PAGE 1450
Field Description ENode-WWPN Worldwide port name (WWPN) of a server CNA port. FCoE-Vlan VLAN ID of the dedicated VLAN used to transmit FCoE traffic to and from the fabric. Fabric-Intf Fabric-facing Fibre Channel port (slot/port) on which FC traffic is transmitted to the specified fabric. Fabric-Map Name of the FCoE map containing the FCoE/FC configuration parameters for the server CNA-fabric connection.
PAGE 1451
Example NPIV Proxy Gateway Field Description Fabric Intf Fabric-facing Fibre Channel port (slot/port) on which FCoE traffic is transmitted to the specified fabric. FCoE VLAN ID of the dedicated VLAN used to transmit FCoE traffic from a server CNA to a fabric and configured on both the serverfacing S5000 port and server CNA port. Fabric Map Name of the FCoE map containing the FCoE/FC configuration parameters for the server CNA-fabric connection.
PAGE 1452
Secs Status Related Commands : : 5593 LOGGED_IN dcb-map — creates a DCB map to configure DCB parameters on Ethernet ports that support converged Ethernet traffic. fcoe-map — creates an FCoE map which contains the parameters used in the communication between servers and a SAN fabric. show fc switch Display the switch configuration for Fibre Channel capability. S5000 Syntax show fc switch Parameters None Command Modes • EXEC • EXEC Privilege Command History Usage Information Version 9.0(1.
PAGE 1453
show qos dcb-map Display the DCB parameters configured in a specified DCB map. S5000 Syntax Parameters Command Modes Command History Usage Information show qos dcb-map map-name map-name • • Displays the PFC and ETS parameters configured in the specified map. EXEC EXEC Privilege Version 9.0(1.3) Introduced on the S5000. Use the show qos dcb-map command to display the enhanced transmission selection (ETS) and priority-based flow control (PFC) parameters used to configure server-facing Ethernet ports.
PAGE 1454
Related Commands 1454 dcb-map — creates a DCB map to configure PFC and ETS parameters and applies the PFC and ETS settings on Ethernet ports.
PAGE 1455
Open Shortest Path First (OSPFv2 and OSPFv3) 45 Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an Interior Gateway Protocol (IGP), which means that it distributes routing information between routers in a single Autonomous System (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1456
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1457
defaultinformationoriginate (OPTIONAL) Allows external routing information to be imported into the NSSA by using Type 7 default. no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1458
mask Specify a mask for the destination prefix. Enter the full mask (for example, 255.255.255.0). not-advertise (OPTIONAL) Enter the keywords not-advertise to set the status to DoNotAdvertise (that is, the Type 3 summary-LSA is suppressed and the component networks remain hidden from other areas.) Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1459
Parameters area-id Specify the OSPF area in dotted decimal format (A.B.C.D.) or enter a number from zero (0) to 65535. no-summary (OPTIONAL) Enter the keywords no-summary to prevent the ABR from sending summary Link State Advertisements (LSAs) into the stub area. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1460
To delete a virtual link, use the no area area-id virtual-link router-id command. To delete a parameter of a virtual link, use the no area area-id virtual-link router-id [[authentication-key [encryption-type] key] | [message-digest-key keyid md5 [encryption-type] key]] [deadinterval seconds] [hello-interval seconds] [retransmit-interval seconds] [transmit-delay seconds] command syntax. Parameters Defaults 1460 area-id Specify the OSPF area in dotted decimal format (A.B.C.D.
PAGE 1461
Command Modes Command History Usage Information ROUTER OSPF Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Deprecated command on the S4810. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. All OSPF areas must be connected to a backbone area (usually Area 0). Virtual links connect broken or discontiguous areas.
PAGE 1462
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables.
PAGE 1463
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. Syntax Parameters clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared.
PAGE 1464
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1465
database-timer rate-limit Command Modes Command History Usage Information (OPTIONAL) Enter the keywords database-timer ratelimit to display the LSA throttling timer information. EXEC Privilege Version 9.0(1.3) Introduced on the S5000. The following describes output for the debug ip ospf command shown in the Example below. Field Description 8:14 Displays the time stamp. OSPF Displays the OSPF process ID: instance ID. v: Displays the OSPF version. Dell Networking OS supports version 2 only.
PAGE 1466
netmask: Displays the destination IP address mask.
PAGE 1467
Parameters always (OPTIONAL) Enter the keyword always to specify that default route information must always be advertised. metric metricvalue (OPTIONAL) Enter the keyword metric then a number to configure a metric value for the route. The range is from 1 to 16777214. metric-type type-value (OPTIONAL) Enter the keywords metric-type then an OSPF link state type of 1 or 2 for default routes.
PAGE 1468
default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command. Syntax default-metric number To return to the default values, use the no default-metric [number] command. Parameters number Enter a number as the metric. The range is from 1 to 16777214. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1469
To remove the OSPF description, use the no description command. Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults none Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1470
ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n format. access-listname (OPTIONAL) Enter the name of an IP standard access list, up to 140 characters. Defaults 110 Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1471
Defaults inter-area dist2 (OPTIONAL) Enter the keywords inter-area then a number to specify a distance metric for routes between areas. The range is from 1 to 255. The default is 110. intra-area dist1 (OPTIONAL) Enter the keywords intra-area then a number to specify a distance metric for all routes within an area. The range is from 1 to 255. The default is 110.
PAGE 1472
To delete a filter, use the no distribute-list prefix-list-name in [interface] command. Parameters prefix-listname Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/ port or number information: • For Port Channel groups, enter the keywords portchannel then a number. For the C-Series, S-Series, and Z9000, the range is from 1 to 128.For Z9500, the range is from 1 to 512.
PAGE 1473
distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters prefix-listname Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed.
PAGE 1474
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF.
PAGE 1475
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on all platforms. The higher this parameter is set, the faster OSPF converge takes place. NOTE: The faster the convergence, the more frequent the route calculations and updates. This behavior impacts CPU utilization and may impact adjacency stability in larger topologies.
PAGE 1476
Usage Information Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. In OSPF, flooding is the most resource-consuming task. The flooding algorithm, described in RFC-2328, requires that OSPF flood LSAs (Link State Advertisements) on all interfaces, as governed by LSA’s flooding scope (see Section 13 of the RFC).
PAGE 1477
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Added support for MultiProcess OSPF. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1478
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1479
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart role Specify the role for your OSPF router during graceful restart.
PAGE 1480
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. Added Restart and Helper roles support on the S-Series. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf auth-change-wait-time OSPF provides a grace period while OSPF changes its interface authentication type.
PAGE 1481
Version Description 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface. Syntax ip ospf authentication-key [encryption-type] key To delete an authentication key, use the no ip ospf authentication-key command. Parameters encryptiontype (OPTIONAL) Enter 7 to encrypt the key. key Enter an eight-character string. Strings longer than eight characters are truncated.
PAGE 1482
Usage Information All neighboring routers in the same network must use the same password to exchange OSPF information. ip ospf cost Change the cost associated with the OSPF traffic on an interface. Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters cost Enter a number as the cost. The range is from 1 to 65535. Defaults The default cost is based on the reference bandwidth. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1483
ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds.
PAGE 1484
ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1485
ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command. Parameters keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. Defaults No MD5 authentication is configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1486
After the reply is received and the new key is authenticated, delete the old key. Dell recommends keeping only one key per interface. NOTE: The MD5 secret is stored as plain text in the configuration file with service password encryption. Write down or otherwise record the key. You cannot learn the key once it is configured. Use caution when changing the key. ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets.
PAGE 1487
ip ospf network Set the network type for the interface. Syntax ip ospf network {broadcast | point-to-point} To return to the default, use the no ip ospf network command. Parameters broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-to-point network. Defaults Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1488
ip ospf priority To determine the designated router for the OSPF network, set the priority of the interface. Syntax ip ospf priority number To return to the default setting, use the no ip ospf priority command. Parameters number Enter a number as the priority. The range is from 0 to 255. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1489
ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies belonging to the interface. Syntax ip ospf retransmit-interval seconds To return to the default values, use the no ip ospf retransmit-interval command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 5 seconds.
PAGE 1490
ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed. Syntax ip ospf transmit-delay seconds To return to the default value, use the no ip ospf transmit-delay command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 1 second. This value must be greater than the transmission and propagation delays for the interface.
PAGE 1491
log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell Networking OS. Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1492
Parameters number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths. Defaults 4 Command Modes ROUTER OSPF for OSPFv2 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1493
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1494
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1495
interface Enter the following keywords and slot/port or number information: • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For Port Channel groups, enter the keywords portchannel then a number. For the C-Series, S-Series, and Z9000, the range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1496
This command behavior has changed as follows: passive-interface interface • The previous no passive-interface interface is removed from the running configuration. • The ABR status for the router is updated. • Save passive-interface interface into the running configuration. passive-interface default • All present and future OSPF interfaces are marked as passive. • Any adjacency is explicitly terminated from all OSPF interfaces.
PAGE 1497
Command Modes Command History Usage Information bfd (OPTIONAL) Enter the keyword bfd to debug only OSPF BFD information. event (OPTIONAL) Enter the keyword event to debug only OSPF event information. packet (OPTIONAL) Enter the keyword packet to debug only OSPF packet information. spf (OPTIONAL) Enter the keyword spf to display the Shortest Path First information. database-timer rate-limit (OPTIONAL) Enter the keywords database-timer ratelimit to display the LSA throttling timer information.
PAGE 1498
auk: If the ip ospf authentication-key command is configured, this field displays the key used. keyid: If the ip ospf message-digest-key command is configured, this field displays the MD5 key to: Displays the interface to which the packet is intended. dst: Displays the destination IP address. netmask: Displays the destination IP address mask.
PAGE 1499
redistribute bgp Redistribute BGP routing information throughout the OSPF instance. Syntax redistribute bgp as number [metric metric-value] | [metric-type type-value] | [tag tag-value] To disable redistribution, use the no redistribute bgp as number [metric metric-value] | [metric-type type-value] [route-map map-name] [tag tag-value] command. Parameters as number Enter the autonomous system number. The range is from 1 to 65535.
PAGE 1500
Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the keyword default. pre- 6.1.1.1 Introduced on the E-Series. redistribute isis Redistribute IS-IS routing information throughout the OSPF instance.
PAGE 1501
Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1502
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information You can configure an arbitrary value in the IP address format for each router. However, each router ID must be unique.
PAGE 1503
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1504
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1505
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1506
Dell# Related Commands Area ranges are show ip ospf database — displays information about the OSPF routes configured. show ip ospf interface — displays the OSPF interfaces configured. show ip ospf neighbor — displays the OSPF neighbors configured. show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. Syntax Parameters show ip ospf [process-id] asbr process-id Enter the OSPF Process ID to show a specific process.
PAGE 1507
Usage Information To isolate problems with external routes, use this command. In OSPF, external routes are calculated by adding the LSA cost to the cost of reaching the ASBR router. If an external route does not have the correct cost, use this command to determine if the path to the originating router is correct. The display output is not sorted in any order. NOTE: ASBRs that are not in directly connected areas are also displayed.
PAGE 1508
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database command shown in the following example.
PAGE 1509
12.1.2.0 13.1.1.0 13.1.2.0 172.16.1.0 Dell> Related Commands 192.68.135.2 13.1.1.1 13.1.1.1 13.1.1.1 1663 1192 1184 148 0x80000054 0x8000006b 0x8000006b 0x8000006d 0xd8d6 0x2718 0x1c22 0x533b 0 0 0 0 show ip ospf database asbr-summary — displays only ASBR summary LSA information. show ip ospf database asbr-summary Display information about autonomous system (AS) boundary LSAs.
PAGE 1510
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf database asbr-summary command shown in the following example. Field Description LS Age Displays the LSA’s age.
PAGE 1511
LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000000f Checksum: 0x8221 Length: 28 Network Mask: /0 TOS: 0 Metric: 2 LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x80000010 Checksum: 0x4198 Length: 28 --More-Related Commands show ip ospf database — displays OSPF database information.
PAGE 1512
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1512 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1513
Example Field Description Metrics Type Displays the external type. TOS Displays the Type of Service (TOS) options. Option 0 is the only option. Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router. External Route Tag Displays the 32-bit field attached to each external route.
PAGE 1514
show ip ospf database network Display the network (type 2) LSA information. Syntax Parameters show ip ospf [process-id] database network [link-state-id] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1515
Usage Information Example The following describes the show ip ospf process-id database network command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1516
Checksum: 0x4309 Length: 36 Network Mask: /24 Attached Router: 192.10.10.2 Attached Router: 20.20.20.1 Attached Router: 20.20.20.5 Dell# Related Commands show ip ospf database — displays OSPF database information. show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. Syntax Parameters show ip ospf [process-id] database nssa-external [link-stateid] [adv-router ip-address] process-id Enter the OSPF Process ID to show a specific process.
PAGE 1517
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. show ip ospf database — displays OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information.
PAGE 1518
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1518 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1519
Example Item Description Opaque ID Displays the Opaque type-specific ID (the remaining 24 bits of the Link State ID). Dell>show ip ospf 1 database opaque-area OSPF Router with ID (3.3.3.3) (Process ID 1) Type-10 Opaque Link Area (Area 0) LS age: 1133 Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.1 Advertising Router: 10.16.1.
PAGE 1520
• adv-router ipaddress the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ipaddress to display only the LSA information about that router. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1521
link-state-id adv-router ipaddress (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router then the IP address of an Advertising Router to display only the LSA information about that router.
PAGE 1522
show ip ospf database router Display the router (type 1) LSA information. Syntax Parameters show ip ospf [process-id] database router [link-state-id] [advrouter ip-address] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1523
Usage Information Example The following describes the show ip ospf process-id database router command shown in the following example. Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1524
LS Seq Number: 0x8000012f Checksum: 0x3357 Length: 144 AS Boundary Router Area Border Router Number of Links: 10 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.129.1 (Link Data) Router Interface address: 192.68.129.1 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.130.1 (Link Data) Router Interface address: 192.68.130.
PAGE 1525
link-state-id adv-router ipaddress (OPTIONAL) Specify LSA ID in dotted decimal format. The LSA ID value depends on the LSA type, and it can be one of the following: • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router then the IP address of an Advertising Router to display only the LSA information about that router.
PAGE 1526
Item Example Description • DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. • E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. LS Seq Number Displays the link state sequence number. This number allows you to identify old or duplicate LSAs.
PAGE 1527
Checksum: 0x1241 Length: 28 Network Mask: /26 TOS: 0 Metric: 1 Dell# Related Commands show ip ospf database — displays OSPF database information. show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated. S5000 Syntax Parameters show ip ospf [process-id | vrf vrf-name] interface [interface] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1528
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1529
Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1 Designated Router (ID) 192.168.253.2, Interface address 192.168.1.2 Backup Designated Router (ID) 192.168.253.1, Interface address 192.168.1.1 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:02 Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 192.168.253.
PAGE 1530
The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1531
show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Syntax Parameters show ip ospf [process-id] routes process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1532
NOTE: Starting with Version 9.4(0.0), the loopback IP address advertised to the neighbor is not displayed in the output because they are not accounted as inactive OSPF routes, whereas the loopback IP address is displayed until Dell Networking OS Version 9.3(0.0). Starting with Version 9.4(0.0), the show ip ospf routes command displays the interface and area ID information of connected networks in addition to the other settings, whereas these details are not displayed until Dell Networking OS Version 9.3(0.
PAGE 1533
neighbor router-id • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.). Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1534
Row Heading Description LSUpd Number of link state update packets. LSAck Number of link state acknowledgement packets. TxQ-Len The transmission queue length. RxQ-Len The reception queue length. Tx-Mark The highest number mark in the transmission queue. Rx-Mark The highest number mark in the reception queue. Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets.
PAGE 1535
Example Error Type Description Seq-no A sequence no errors occurred during the database exchange process. Socket Socket Read/Write operation error. Q-overflow Packets dropped due to queue overflow. Unknown-Pkt Received packet is not an OSPF packet.
PAGE 1536
RtidZero 0 Neighbor ID 4.4.4.4 Packet Statistics Hello DDiscr LSReq LSUpd LSAck RX 5 2 1 3 2 TX 6 5 1 3 3 Timers Hello 0 Wait 0 Grace 0 Dead 39 Transmit 4 Queue Statistics LSU-Q-Len 0 LSU-Q-Wmark 1 LSR-Q-Len 0 LSR-Q-Wmark 1 Dell(conf-if-te-1/6)# Related Commands clear ip ospf statistics — clears the packet statistics in all interfaces and neighbors. show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire.
PAGE 1537
Example Dell#show ip ospf 10 timers rate-limit List of LSAs in rate limit Queue LSA id: 1.1.1.0 Type: 3 Adv Rtid: 3.3.3.3 Expiry time: 00:00:09.111 LSA id: 3.3.3.3 Type: 1 Adv Rtid: 3.3.3.3 Expiry time: 00:00:23.96 Dell# show ip ospf topology Display routers in directly connected areas. Syntax Parameters show ip ospf [process-id] topology process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1538
of reaching the router. If an inter-area or external route is not of correct cost, the display can determine if the path to the originating router is correct or not. Example Dell#show ip ospf 1 topology Router ID 3.3.3.3 1.1.1.1 Dell# Flags Cost E/B/-/ 1 E/-/-/ 1 Nexthop 20.0.0.3 10.0.0.1 Interface Area Gi 13/1 0 Gi 7/1 1 show ip ospf virtual-links Display the OSPF virtual links configured and is useful for debugging OSPF routing operations.
PAGE 1539
Example Items Description “Transit area...” This line identifies the area through which the virtual link was created, the interface used, and the cost assigned to that link. “Transmit Delay...” This line displays the transmit delay assigned to the link and the State of the OSPF neighbor. “Timer intervals...” This line displays the timer values assigned to the virtual link. The timers are Hello is hello-interval, Dead is dead-interval, Wait is transmit-delay, and Retransmit is retransmit-interval.
PAGE 1540
tag tag-value (OPTIONAL) Enter the keyword tag then a value to match on routes redistributed through a route map. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.
PAGE 1541
timers spf Set the time interval between when the switch receives a topology change and starts a shortest path first (SPF) calculation. Syntax timers spf delay holdtime To return to the default, use the no timers spf command. Parameters Defaults delay Enter a number as the delay. The range is from 0 to 4294967295. The default is 5 seconds. holdtime Enter a number as the hold time. The range is from 0 to 4294967295. The default is 10 seconds.
PAGE 1542
timers throttle lsa all Configure LSA transmit intervals. Syntax timers throttle lsa all {start-interval | hold-interval | maxinterval} To return to the default, use the no timers throttle lsa command. Parameters Defaults start-interval Set the minimum interval between initial sending and resending the same LSA. The range is from 0 to 600,000 milliseconds. hold-interval Set the next interval to send the same LSA.
PAGE 1543
100,000, the LSA is sent at 5000 msec, then 1000 msec, then 2000 msec, them 4000 until 100,000 msec is reached. timers throttle lsa arrival Configure the LSA acceptance intervals. Syntax timers throttle lsa arrival arrival-time To return to the default, use the no timers throttle lsa command. Parameters arrival-time Set the interval between receiving the same LSA repeatedly, to allow sufficient time for the system to accept the LSA. The range is from 0 to 600,000 milliseconds.
PAGE 1544
The Dell Networking implementation of OSPFv3 is based on IETF RFC 2740. area authentication Configure an IPsec authentication policy for OSPFv3 packets in an OFSPFv3 area. Syntax Parameters area area-id authentication ipsec spi number {MD5 | SHA1} [keyencryption-type] key area area-id Area for which OSPFv3 traffic is to be authenticated. For area-id, you can enter a number. The range is from 0 to 4294967295. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy.
PAGE 1545
Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.2.0 Introduced on the E-Series TeraScale. Before you enable IPsec authentication on an OSPFv3 area, you must first enable OSPFv3 globally on the router. Configure the same authentication policy (same SPI and key) on each interface in an OSPFv3 link. An SPI number must be unique to one IPsec security policy (authentication or encryption) on the router.
PAGE 1546
esp encryptionalgorithm Encryption algorithm used with ESP. Valid values are: 3DES, DES, AES-CBC, and NULL. For AES-CBC, only the AES-128 and AES-192 ciphers are supported. keyencryptionalgorithm (OPTIONAL) Specifies if the key is encrypted. key Text string used in encryption. Valid values: 0 (key is not encrypted) or 7 (key is encrypted).
PAGE 1547
Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series TeraScale. 8.3.19.0 Introduced on the S4820T. Before you enable IPsec encryption on an OSPFv3 interface, first enable OSPFv3 globally on the router. Configure the same encryption policy (same SPI and keys) on each interface in an OSPFv3 link. An SPI value must be unique to one IPsec security policy (authentication or encryption) on the router.
PAGE 1548
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1549
Example Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1550
• For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1551
Lines Beginning With or Including Description • 7 - external LSA • 8 - link-state advertisement (OSPFv3) • 9 - link local LSA (OSPFv2), Intra-Area-Prefix LSA (OSPFv3) • 11 - grace LSA (OSPFv3) Length: Displays the packet length. Router ID: Displays the OSPF3 router ID. Area ID: Displays the Area ID. Chksum: Displays the OSPF3 checksum. default-information originate Configure the Dell Networking OS to generate a default external route into an OSPFv3 routing domain.
PAGE 1552
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. redistribute — redistributes routes from other routing protocols into OSPFv3.
PAGE 1553
restart grace-period command. The grace period is the length of time that OSPFv3 neighbors continue to advertise the restarting router as though it is fully adjacent. When graceful restart is enabled (restarting role), an OSPFv3 restarting expects its OSPFv3 neighbors to help when it restarts by not advertising the broken link.
PAGE 1554
• An unplanned restart occurs when an unplanned event causes the active RPM to switch to the backup RPM, such as when an active process crashes, the active RPM is removed, or a power failure happens. During an unplanned restart, OSPF sends out a Grace LSA when the backup RPM comes online. By default, both planned and unplanned restarts trigger an OSPFv3 graceful restart. Selecting one or the other mode restricts OSPFv3 to the single selected mode. ipv6 ospf area Enable IPv6 OSPF on an interface.
PAGE 1555
keyencryptiontype (OPTIONAL) Specifies if the key is encrypted. key Text string used in authentication. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). For MD5 authentication, the key must be 32 hex digits (nonencrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1556
show crypto ipsec sa ipv6 – displays the security associations set up for OSPFv3 interfaces in authentication policies. ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters.
PAGE 1557
Usage Information Version Description 9.2.0.0 Introduced on the Z9000, S4820T, and S4810. This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode.
PAGE 1558
• TenGigabitEthernet—Default cost is 1 • FortygigEthernet — Default cost is 1 • Ethernet—Default cost is 10 ipv6 ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the time interval elapses, the neighboring routers declare the router down. Syntax ipv6 ospf dead-interval seconds To return to the default time interval, use the no ipv6 ospf dead-interval command. Parameters seconds Enter the time interval in seconds.
PAGE 1559
ipv6 ospf encryption Configure an IPsec encryption policy for OSPFv3 packets on an IPv6 interface. Syntax Parameters ipv6 ospf encryption {null | ipsec spi number esp encryptionalgorithm [key-encryption-type] key athentication-algorithm [key-encryption-type] key}} null Causes an encryption policy configured for the area to not be inherited on the interface. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1560
For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.
PAGE 1561
To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.
PAGE 1562
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1563
Use this command for interfaces connected to multi-access networks, not pointto-point networks. ipv6 router ospf Enable OSPF for IPv6 router configuration. S5000 Syntax ipv6 router ospf process-id [vrf vrf-name] To exit OSPF for IPv6, use the no ipv6 router ospf process-id command. Parameters process-id Enter the process identification number. The range is from 1 to 65535. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF.
PAGE 1564
Parameters number Defaults 8 Command Modes ROUTER OSPF Command History Specify the number of paths. The range is from 1 to 64. The default is 8 paths. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series.
PAGE 1565
Command History Usage Information Version Description 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. By default, no interfaces are passive. Routing updates are sent to all interfaces on which the routing protocol is enabled.
PAGE 1566
metric metricvalue Enter the keyword metric then the metric value. The range is from 0 to 16777214. The default is 20. metric-type type-value (OPTIONAL) Enter the keywords metric-type then the OSPFv3 link state type of 1 or 2 for default routes. The values are: • 1 for a type 1 external route • 2 for a type 2 external route The default is 2. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of an established route map.
PAGE 1567
Related Commands default-information originate – configures default external route into OSPFv3. router-id Designate a fixed router ID. Syntax router-id ip-address To return to the previous router ID, use the no router-id ip-address command. Parameters ip-address Enter the router ID in the dotted decimal format. Defaults The router ID is selected automatically from the set of IPv4 addresses configured on a router.
PAGE 1568
show crypto ipsec policy Display the configuration of IPsec authentication and encryption policies. Syntax Parameters show crypto ipsec policy [name name] name name (OPTIONAL) Displays configuration details about a specified policy. Defaults No default behavior or values. Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1569
123456789a123456789b123456789c123456789d12345678 Transform set : esp-3des esp-md5-hmac Crypto IPSec client security policy data Policy name : OSPFv3-0-501 Policy refcount : 1 Inbound ESP SPI : 501 (0x1F5) Outbound ESP SPI : 501 (0x1F5) Inbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97 eb7c0 c30808825fb5 Outbound ESP Auth Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba8ed8bb5efe91e97 eb7c0 c30808825fb5 Inbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759
PAGE 1570
show crypto ipsec sa ipv6 Display the IPsec security associations (SAs) used on OSPFv3 interfaces. Syntax Parameters show crypto ipsec sa ipv6 [interface interface] interface interface (OPTIONAL) Displays information about the SAs used on a specified OSPFv3 interface, where interface is one of the following values: • • • • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1571
Interface: TenGigabitEthernet 1/1 Link Local address: fe80::201:e8ff:fe40:4d10 IPSecv6 policy name: OSPFv3-1-500 inbound ah sas spi : 500 (0x1f4) transform : ah-md5-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE outbound ah sas spi : 500 (0x1f4) transform : ah-md5-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE inbound esp sas outbound esp sas Interface: TenGigabitEthernet 1/2 Link Local address: fe80::201:e8ff:fe40:4d11 IPSecv6 policy nam
PAGE 1572
inbound/outbound esp Encryption policy applied to inbound or outbound traffic. spi Security policy index number used to identify the policy. transform Security algorithm that is used to provide authentication, integrity, and confidentiality. in use settings Transform that the SA uses (only transport mode is supported). replay detection support Y: An SA has enabled the replay detection feature. N: The replay detection feature is not enabled.
PAGE 1573
Version Description 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.4.2.2 Added support for the display of graceful restart parameters and Type-11 Grace LSAs on E-Series TeraScale routers. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. Usage Information The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router.
PAGE 1574
Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 Area 1 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 8 Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 E1200-T2C2#sh ipv6 ospf neighbor Neighbor ID ID Interface 63.114.8.
PAGE 1575
Defaults none Command Modes EXEC Command History Usage Information Version Description 9.2.(0.0) Added support for showing BFD status on the S4820T, S4810, and Z9000. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. If you enable BFD at the global level, show ipv6 ospf interface shows the BFD provisioning.
PAGE 1576
NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. interface Defaults none Command Modes EXEC (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information.
PAGE 1577
Policy-based Routing (PBR) 46 Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell Networking Operating System (OS).
PAGE 1578
Related Commands Version Description 7.7.1.0 Introduced on the E-Series ExaScale. ip redirect-list – enables an IP Redirect List. ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name To remove a redirect list from an interface, use the no ip redirect-group name command.
PAGE 1579
Related Commands • show cam pbr – displays the content of the PBR CAM. • show ip redirect-list – displays the redirect-list configuration. ip redirect-list Configure a redirect list and enter REDIRECT-LIST mode. Syntax ip redirect-list redirect-list-name To remove a redirect list, use the no ip redirect-list command. Parameters redirect-listname Defaults None Command Modes CONFIGURATION Command History Enter the name of a redirect list. Version Description 9.7(0.
PAGE 1580
Parameters • If you know the filter sequence number, use the no seq sequence-number syntax command. • You can also use the no permit {ip-protocol-number | protocoltype} {source mask | any | host ip-address} {destination mask | any | host ip-address} [bit] [operators] command. ip-protocolnumber Enter a number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1581
Defaults none Command Modes REDIRECT-LIST Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series Tera Scale. 7.7.1.0 Introduced on the E-Series ExaScale. redirect Configure a rule for the redirect list.
PAGE 1582
ip-protocolnumber Enter a number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1583
Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, and Z9000. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series Tera Scale. 7.7.1.0 Introduced on the E-Series ExaScale. seq Configure a filter with an assigned sequence number for the redirect list.
PAGE 1584
protocol-type Enter one of the following keywords as the protocol type: • • ip for any internet protocol • tcp for transmission control protocol • udp for user datagram protocol source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address.
PAGE 1585
destinationport-range Defaults none Command Modes REDIRECT-LIST Command History Enter the keywords destination-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, and Z9000. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. show cam pbr Display the PBR CAM content.
PAGE 1586
Usage Information The show cam pbr command displays the PBR CAM content. Example Dell#show cam pbr stack-unit 1 port-set 0 TCP Flag: Bit 5 - URG, Bit 4 - ACK, Bit 3 - PSH, Bit 2 - RST, Bit 1 - SYN, Bit 0 - FIN Cam Port VlanID Proto Tcp Src Dst SrcIp DstIp Next-hop Egress Index Flag Port Port MAC Port ---------------------------------------------------------------------------------------------------------------------------------------00000 5 N/A IP 0x0 0 0 22.22.2.22/32 33.33.3.
PAGE 1587
Command History Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. Dell#show ip redirect-list explicit_tunnel IP redirect-list explicit_tunnel: Defined as: seq 5 redirect tunnel 1 track 1 tcp 155.55.2.0/24 222.22.2.0/24, Track 1 [up], Next-hop reachable (via Te 1/32) seq 10 redirect tunnel 1 track 1 tcp any any, Track 1 [up], Next-hop reachable (via Te 1/32) seq 15 redirect tunnel 2 udp 155.55.0.0/16 host 144.144.144.
PAGE 1588
47 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the platform. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim snooping tib Clear tree information discovered by PIM-SM snooping from the PIM database.
PAGE 1589
clear ip pim tib Clear PIM tree information from the PIM database. S5000 Syntax Parameters clear ip pim [vrf vrf-name] tib [group] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group (OPTIONAL) Enter the multicast group address in dotted decimal format (A.B.C.D). Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1590
clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement. S5000 Syntax Parameters clear ip pim [vrf vrf-name] rp-mapping [rp-address] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. rp-address (OPTIONAL) Enter the RP address in dotted decimal format (A.B.C.D).
PAGE 1591
debug ip pim View IP PIM debugging messages. S5000 Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug allto disable all debugging command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF.
PAGE 1592
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000.
PAGE 1593
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. This command is applied to the subsequent PIM-BSR. Existing BSR advertisements are cleaned up by time-out. To clean the candidate RP advertisements, use the clear ip pim rp-mapping command. ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router.
PAGE 1594
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1595
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series on port-channels and the SSeries. The router with the largest value assigned to an interface becomes the designated router.
PAGE 1596
Command History Usage Information Version 8.2.1.0 Introduced on the E-Series ExaScale. Added the ipv6 option for the E-Series. Version 7.6.1.0 Introduced on the E-Series. When an NSF-capable router comes up, it announces the graceful restart capability and restart duration as a Hello option. The receiving router notes the Hello option. Routers not NSF-capable discard the unknown Hello option and adjacency is not affected.
PAGE 1597
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. 7.7.1.0 Introduced on the E-Series. Example Dell(conf)# ip access-list extended iptv-channels Dell(config-ext-nacl)# permit ip 10.1.2.3/24 225.1.1.0/24 Dell(config-ext-nacl)# permit ip any 232.1.1.
PAGE 1598
Example Version Description 8.4.1.0 Introduced Dell(conf)# ip access-list standard map1 Dell(config-std-nacl)# permit 224.0.0.1/24 Dell(config-std-nacl)#exit Dell(conf)#int tengig 1/1 Dell(config-if-te-1/1)# ip pim ingress-interface-map map1 ip pim neighbor-filter To prevent a router from participating in protocol independent multicast (PIM), configure this feature.
PAGE 1599
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages. Syntax ip pim query-interval seconds To return to the default value, use the no ip pim query-interval seconds command.
PAGE 1600
Version Description 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. S5000 Syntax ip pim [vrf vrf-name] register-filter access-list To return to the default, use the no ip pim [vrf vrf-name] registerfilter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF.
PAGE 1601
Usage Information Version Description 7.6.1.0 Introduced The access name is an extended IP access list that denies PIM register packets to RP at the source DR based on the multicast and group addresses. Do not enter this command before creating the access-list. ip pim rp-address Configure a static PIM rendezvous point (RP) address for a group or access-list.
PAGE 1602
Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. pre- 6.1.1.1 Introduced on the E-Series. First-hop routers use this address by to send register packets on behalf of source multicast hosts.
PAGE 1603
• priority For a VLAN, enter the keyword vlan then a number from 1 to 4094. (OPTIONAL) Enter the priority used in Bootstrap election process. The range is zero (0) to 255. The default is 192. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1604
Command History Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series ExaScale. Because PIM-SM snooping is used in a Layer 2 environment, PIM-SM snooping and PIM multicast routing are mutually exclusive. PIM-SM snooping cannot be enabled on a switch/router if PIM-SM or PIM-DM is enabled. If enabled at the global level, PIM-SM snooping is automatically enabled on all VLANs unless the no ip pim snooping command has been entered on a VLAN.
PAGE 1605
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. The interface must be enabled (the no shutdown command) and not have the switchport command configured.
PAGE 1606
Usage Information Version Description 9.7(0.0) Removed the acl-access-list parameter. Modified the max value of S, G entry second range from 86400 to 65535. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series for the port-channels and the SSeries. 7.7.1.
PAGE 1607
Command History Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1608
ip pim spt-threshold To switch to the shortest path tree when the traffic reaches the specified threshold value, configure the PIM router. S5000 Syntax ip pim [vrf vrf-name] spt-threshold [infinity] To return to the default value, use the no ip pim [vrf vrf-name] sptthreshold [infinity] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1609
To re-enable the flooding of multicast packets to the PIM designated router, use the ip pim snooping dr-flood command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 1610
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1611
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 1612
The show ip pim interface command does not display information corresponding to the loop-back interfaces. Example Dell#show ip pim interface Address Interface Ver/ Mode 165.87.34.5 Te 1/10 v2/S 165.87.34.5 10.1.1.2 Vl 10 v2/S 10.1.1.2 20.1.1.5 Vl 20 v2/S 20.1.1.5 165.87.31.200 Vl 30 v2/S 165.87.31.201 Nbr Count 0 Query Intvl 30 DR Prio 1 1 30 1 1 30 1 1 30 1 DR show ip pim neighbor View PIM neighbors.
PAGE 1613
Field Description Neighbor address Displays the IP address of the PIM neighbor. Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found. Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires). Ver Displays the PIM version number.
PAGE 1614
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1615
Parameters vlan vlan-id (OPTIONAL) Enter a VLAN ID to display information about a specified VLAN configured for PIM-SM snooping. The valid VLAN IDs range is from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1616
show ip pim snooping neighbor Display information on PIM neighbors learned through PIM-SM snooping. Syntax Parameters show ip pim snooping neighbor [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter a VLAN ID to display information about PIM neighbors that PIM-SM snooping discovered on a specified VLAN. The valid VLAN IDs range is from 1 to 4094. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1617
Field Example Description • DR = Designated Router • S = Sparse mode Dell#show ip pim snooping neighbor Neighbor Interface Uptime/Expires Ver Address 165.87.32.2 Vl 2 [Te 1/13 ] 00:04:03/00:01:42 v2 165.87.32.10 Vl 2 [Te 1/11 ] 00:00:46/00:01:29 v2 165.87.32.12 Vl 2 [Te 2/20 ] 00:00:51/00:01:24 v2 DR Prio 1 0 0 show ip pim snooping tib Display information from the tree information base (TIB) PIM-SM snooping discovered about multicast group members and states.
PAGE 1618
Usage Information Example The following describes the show ip pim snooping tib commands shown in the following example. Field Description (S, G) Displays the entry in the PIM multicast snooping database. uptime Displays the amount of time the entry has been in the PIM multicast route table. expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1619
Dell#show ip pim snooping tib vlan 2 225.1.2.1 165.87.1.7 PIM Multicast Snooping Table Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune SGR-P - (S,G,R) Prune Timers: Uptime/Expires * : Inherited port (165.87.1.7, 225.1.2.1), uptime 00:00:08, expires 00:02:52, flags: j Incoming interface: Vlan 2, RPF neighbor 0.0.0.0 Outgoing interface list: TenGigabitEthernet 2/11 Upstream Port -/TenGigabitEthernet 2/13 DR Port -/TenGigabitEthernet 2/20 RPF 165.87.32.
PAGE 1620
show ip pim summary View information about PIM-SM operation. S5000 Syntax Command Modes Command History show ip pim [vrf vrf-name] summary • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.
PAGE 1621
Message summary: 2582/2583 Joins sent/received 5/0 Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 State-Refresh messages sent/received 0/0 MSDP updates sent/received 0/0 Null Register messages sent/received 0/0 Register-stop messages sent/received Data path event summary: 0 no-cache messages received 0 last-hop switchover messages received 0/0 pim-assert messages sent/received 0/0 register messages sent/received show ip pim tib View the PIM tree inform
PAGE 1622
Usage Information 1622 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim tib command shown in the following example. Field Description (S, G) Displays the entry in the multicast PIM database. uptime Displays the amount of time the entry has been in the PIM route table.
PAGE 1623
Example Dell#do show ip pim tib PIM Multicast Routing Table Flags: D - Dense, S - Sparse, C - Connected, L - Local, P Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J Join SPT, M - MSDP created entry, A - Candidate for MSDP Advertisement K - Ack-Pending State Timers: Uptime/Expires Interface state: Interface, next-Hop, State/Mode (*, 225.1.1.1), uptime 00:40:16, expires 00:00:00, RP 20.40.4.4, flags: SCJ Incoming interface: Vlan 2007, RPF neighbor 20.30.124.
PAGE 1624
Example 1624 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the E-Series ExaScale.
PAGE 1625
PIM-Source Specific Mode (PIM-SSM) 48 The protocol-independent multicast source-specific mode (PIM-SSM) commands in this section are supported in the Dell Networking operating system. IPv4 PIM Commands The following commands apply to IPv4 PIM-SM, IPv4 PIM-SSM, and PIM-DM.
PAGE 1626
access_list_na me Enter the name of the access list. Defaults Default SSM range is 232/8 and ff3x/32 Command Modes CONFIGURATION Command History Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.
PAGE 1627
show ip pim ssm-range Display the non-default groups added using the SSM range feature. S5000 Syntax show ip pim [vrf vrf-name] ssm-range Defaults none Command Modes • EXEC • EXEC Privilege Command History Exmaple Version Description 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1628
49 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). • The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1629
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1630
set ip dscp Configures the Differentiated Services Code Point (DSCP) value of the packets in the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic. To revert to the default value, use the no form of this command. dscp_value DSCP value of the packets in the ERSPAN traffic. The range is from 0 to 63. The default value is 0. set ip ttl Configures the IP time-to-live (TTL) value of the Encapsulated Remote Switched Port Analyzer (ERSPAN) traffic.
PAGE 1631
Related Command show monitor session — displays the monitor session. show running-config monitor session — displays the running configuration of a monitor session. show config Display the current monitor session configuration. Syntax show config Defaults none Command Modes MONITOR SESSION (conf-mon-sess-session-ID) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1632
show monitor session Display information about monitoring sessions. Syntax show monitor session {session-ID} To display monitoring information for all sessions, use the show monitor session command. Parameters session-ID (OPTIONAL) Enter a session identification number. The range is from 0 to 65535. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific.
PAGE 1633
Related Commands monitor session — creates a monitoring session. show running-config monitor session Display the running configuration of all monitor sessions or a specific session. Syntax show running-config monitor session {session-ID} To display the running configuration for all monitor sessions, use the show running-config monitor session command. Parameters Defaults Command Modes Command History session-ID (OPTIONAL) Enter a session identification number. The range from 0 to 65535.
PAGE 1634
Related Commands monitor session — creates a monitoring session. show monitor session — displays a monitoring session. source (port monitoring) Configure a port monitor source. Syntax source interface | range destination interface direction {rx | tx | both} To disable a monitor source, use the no source interface destination interface direction {rx | tx | both} command.
PAGE 1635
direction {rx | tx | both} Enter the keyword direction then one of the packet directional indicators. • rx: to monitor receiving packets only. • tx: to monitor transmitting packets only. • both: to monitor both transmitting and receiving packets. Defaults none Command Modes MONITOR SESSION (conf-mon- sess-session-ID) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1636
Per-VLAN Spanning Tree Plus (PVST+) 50 The Dell Networking operating software implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell Networking OS supports PVST+ on the platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line. description Enter a description of the PVST+. Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1637
Related Commands Version Description pre- 7.7.1.1 Introduced. protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. Syntax disable To enable PVST+, use the no disable command. Defaults Disabled. Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1638
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1639
Related Commands protocol spanning-tree pvst – enter SPANNING TREE mode on the switch. protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1640
Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports. Related Commands disable — disables PVST+. show spanning-tree pvst — displays the PVST+ configuration. show spanning-tree pvst View the Per-VLAN spanning tree configuration. Syntax Parameters show spanning-tree pvst [vlan vlan-id] [brief] [guard] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094.
PAGE 1641
Usage Information Example (Brief) Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.4.2.1 Support for the optional guard keyword was added on the C-Series, S-Series, and E-Series TeraScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.
PAGE 1642
----------------------------------------------------Te 1/0 Root 128.130 128 20000 FWD 20000 P2P No Te 1/1 Altr 128.131 128 20000 BLK 20000 P2P No Te 1/16 Desg 128.146 128 20000 FWD 20000 P2P Yes Te 1/17 Desg 128.147 128 20000 FWD 20000 P2P Yes Example Dell#show spanning-tree pvst vlan 2 VLAN 2 Root Identifier has priority 4096, Address 0001.e805.e306 Root Bridge hello time 2, max age 20, forward delay 15 Bridge Identifier has priority 4096, Address 0001.e805.
PAGE 1643
Link type: point-to-point (auto) bpdu filter:disable (default) Bpdu guard :disable (default) Bpdus sent 152, received 27562 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ----------------------------------------------------------Te 1/1 128.1223 128 20000 EDS 0 32768 0001.e800.a12b 128.
PAGE 1644
Parameters edge-port Enter the keywords edge-port to configure the interface as a PVST+ edge port. bpduguard Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails. Enter the keyword bpduguard to disable the port when it receives a BPDU. shutdown-onviolation (OPTIONAL) Enter the keywords shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled.
PAGE 1645
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.
PAGE 1646
When used in a PVST+ network, loop guard is performed per-port or per-port channel at a VLAN level. If no BPDUs are received on a VLAN interface, the port or port-channel transitions to a Loop-Inconsistent (blocking) state only for this VLAN. Enabling Portfast BPDU guard and loop guard at the same time on a port results in a port that remains in a Blocking state and prevents traffic from flowing through it.
PAGE 1647
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced. Some non-Dell Networking systems which have hybrid ports participating in PVST+ transmit two kinds of BPDUs: an 802.1D BPDU and an untagged PVST+ BPDU. Dell Networking systems do not expect PVST+ BPDU on an untagged port. If this happens, Dell Networking OS places the port in the Error-Disable state.
PAGE 1648
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. By default, Dell Networking OS implements an optimized flush mechanism for PVST+. This implementation helps in flushing the MAC addresses only when necessary (and less often) allowing for faster convergence during topology changes.
PAGE 1649
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. vlan forward-delay — changes the time interval before Dell Networking OS transitions to the Forwarding state. vlan hello-time — change the time interval between BPDUs. vlan max-age — changes the time interval before PVST+ refreshes.
PAGE 1650
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. vlan bridge-priority — sets the bridge-priority value. vlan hello-time — changes the time interval between BPDUs. vlan max-age — changes the time interval before PVST+ refreshes.
PAGE 1651
Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced. vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — changes the time interval before Dell Networking OS transitions to the forwarding state.
PAGE 1652
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 1653
Quality of Service (QoS) 51 The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking Products. platform. This chapter contains the following sections: • Global Configuration Commands • Per-Port QoS Commands • Policy-Based QoS Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1654
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives. Syntax dot1p-priority priority-value To delete the IEEE 802.
PAGE 1655
Usage Information The dot1p-priority command changes the priority of incoming traffic on the interface. The system places traffic marked with a priority in the correct queue and processes that traffic according to its queue. When you set the priority for a port channel, the physical interfaces assigned to the port channel are configured with the same value. You cannot assign the dot1ppriority command to individual interfaces in a port channel.
PAGE 1656
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information NOTE: Per Port rate police is supported for Layer 2 tagged and untagged switched traffic and for Layer 3 traffic. Per VLAN rate police is supported on only tagged ports with Layer 2 switched traffic. S-Series rate shape Shape the traffic output on the selected interface.
PAGE 1657
Usage Information Version Description 8.3.7.0 Introduced on the S4810. On 40-port 10G stack-unit if the traffic is shaped between 64 and 1000 Kbs, for some values, the shaped rate is much less than the value configured. NOTE: When packets of size greater than 7000 bytes are expected to be received from the network, Dell Networking recommends that you configure the burst value to be more than 175 KB if you configured the rate shape. Such a setting ensures proper bandwidth sharing across queues.
PAGE 1658
Version Description 8.3.7.0 Introduced on the S4810. Usage Information To apply dot1p-queue-mapping, use the service-class dynamic dot1p command. Related Commands show qos dot1p-queue-mapping — displays the dot1p priority to queue mapping on the switch. service-class dynamic dot1p Honor all 802.1p markings on incoming switched traffic on an interface (from INTERFACE mode) or on all interfaces (from CONFIGURATION mode). A CONFIGURATION mode entry supersedes an INTERFACE mode entry.
PAGE 1659
assigned to the port channel are automatically configured; you cannot assign the service-class dynamic command to individual interfaces in a port channel. • All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally. • Layer 2 or Layer 3 service policies supersede dot1p service classes. service-class bandwidth-weight Specify a minimum bandwidth for queues.
PAGE 1660
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1661
Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.1.9.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1662
class-mapname Enter a name of the class for the class map in a character format (32 character maximum). cpu-qos Enter the keyword cpu-qos to assign this Class Map to control plane traffic only (CoPP). layer2 Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Defaults Layer 3 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1663
match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL. match mac dot1p — configures a match criterion for a class map based on a dot1p value. match mac vlan — configures a match criterion for a class map based on VLAN ID. service-queue — assigns a class map and QoS policy to different queues. show qos class-map — views the current class map information. clear qos statistics Clear qos statistics clears statistics from show qos statistics.
PAGE 1664
Related Commands show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the policies (80 characters maximum).
PAGE 1665
match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IPany class-maps on both ACLs as well as VLANs. Syntax match ip access-group access-group-name [set-ip-dscp value | set-color value] To remove ACL match criteria from a class map, use the no match ip accessgroup access-group-name [set-ip-dscp value | set-color value] command.
PAGE 1666
Related Commands class-map — identifies the class map. match ip dscp Use a differentiated services code point (DSCP) value as a match criteria. Syntax match {ip | ipv6 | ip-any} dscp dscp-list [set-ip-dscp value] To remove a DSCP value as a match criteria, use the no match {ip | ipv6 | ip-any} dscp dscp-list [[multicast] set-ip-dscp value] command. Parameters ip Enter the keyword ip to support IPv4 traffic. ipv6 Enter the keyword ipv6 to support IPv6 traffic.
PAGE 1667
Usage Information Version Description 8.3.7.0 Introduced on the S4810. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip dscp and match ip precedence commands are mutually exclusive. Up to 64 IP DSCP values can be matched in one match statement. For example, to indicate IP DCSP values 0 1 2 3 4 5 6 7, enter either the match ip dscp 0,1,2,3,4,5,6,7 or match ip dscp 0-7 command.
PAGE 1668
Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for the ipv6 and ip-any options on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.
PAGE 1669
Parameters vlan vlan-id Enter the keyword vlan and then the ID of the VLAN. The range is from 1 to 4094. Defaults none Command Modes CONF-CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5.(0.
PAGE 1670
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5.(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Use this command to match an IP class-map against a single VRF ID . Related Commands class-map — identifies the class map.
PAGE 1671
Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands class-map — identifies the class map. match mac dot1p Configure a match criterion for a class map based on a dot1p value. Syntax Parameters match mac dot1p {dot1p-list} dot1p-list Enter a dot1p value. The range is from 0 to 7. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific.
PAGE 1672
match mac vlan Configure a match criterion for a class map based on VLAN ID. Syntax Parameters match mac vlan number number Enter the VLAN ID. The range is from 1 to 4094. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 1673
Parameters qos-policyname Enter the name of the policy map in character format (32 characters maximum). Defaults none Command Modes CONFIGURATION (policy-map-input and policy-map-output) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.
PAGE 1674
Defaults Layer 3 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1675
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map. This command enables Policy-Map-Output Configuration mode (conf-policymap-out).
PAGE 1676
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1677
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Usage Information Use this command to specify the name of the output QoS policy. Once output policy is specified, rate-shape, scheduler strict, bandwidth-percentage, and WRED can be defined.
PAGE 1678
Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_g. multicastbandwidth percentage (OPTIONAL) Enter the keywords multicast-bandwidth then the bandwidth percentage. The range is from 0 to 100%. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1679
queue ingress Assign a WRED Curve to all eight ingress Multicast queues or designate the percentage for the Multicast bandwidth queue. Syntax queue ingress multicast {linecard slot number port-set number | all} [wred-profile name] To return to the default, use the no queue ingress multicast {linecard slot number port-set number | all} [wred-profile name] command. Parameters linecard number Enter the keyword linecard then the line card slot number.
PAGE 1680
NOTE: The multicast-bandwidth option is not supported on queue ingress. If you attempt to use the multicast-bandwidth option, the following reject error message is generated: % Error:Bandwidth-percent is not allowed for ingress multicast. rate-police Specify the policing functionality on incoming traffic. Syntax Parameters rate-police [kbps] committed-rate [burst-KB] [peak [kbps] peakrate [burst-KB]] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps).
PAGE 1681
Version Description 8.3.7.0 Introduced on the S4810. Usage Information The default burst size is 100Kb. If a different value is required, you must configure the burst size to the required value. Related Commands rate police — specifies traffic policing on the selected interface. qos-policy-input — creates a QoS output policy. rate-shape Shape traffic output as part of the designated policy.
PAGE 1682
Usage Information On 40-port 10G stack-unit if the traffic is shaped between 64 and 1000 Kbs, for some values, the shaped rate is much less than the value configured. Related Commands rate shape — shapes traffic output as part of the designated policy. qos-policy-output — creates a QoS output policy. service-policy input Apply an input policy map to the selected interface.
PAGE 1683
NOTE: The service-policy commands are not allowed on a port channel. The service-policy input policy-map-name command and the service-class dynamic dot1p command are not allowed simultaneously on an interface. Related Commands policy-map-input — creates an input policy map. service-policy output Apply an output policy map to the selected interface. Syntax service-policy output policy-map-name To remove the output policy map from the interface, use the no servicepolicy output policy-map-name command.
PAGE 1684
service-queue Assign a class map and QoS policy to different queues. Syntax service-queue queue-id [class-map class-map-name] [qos-policy qos-policy-name] To remove the queue assignment, use the no service-queue queue-id [class-map class-map-name] [qos-policy qos-policy-name] command. Parameters queue-id Enter the value used to identify a queue. The range is from 0 to 7.
PAGE 1685
Related Commands class-map — identifies the class map. service-policy input — applies an input policy map to the selected interface. service-policy output — applies an output policy map to the selected interface. set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. Syntax Parameters set {ip-dscp value | mac-dot1p value} ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63.
PAGE 1686
show qos class-map View the current class map information. Syntax Parameters show qos class-map [class-name] class-name (Optional) Enter the name of a configured class map. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1687
• Queue: 2 0 1 3 4 5 6 7 Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1688
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1689
Defaults Command Modes Command History none • • EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1690
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1691
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. Dell#show qos qos-policy-input Qos-policy-input QosInput Rate-police 100 50 peak 100 50 Dscp 32 Dell# show qos qos-policy-output View the output QoS policy details. Syntax Parameters show qos qos-policy-output [qos-policy-name] qos-policyname Enter the QoS policy name.
PAGE 1692
Example Dell#show qos qos-policy-output Qos-policy-output qosOut Rate-limit 50 50 peak 50 50 Wred yellow 1 Wred green 1 show qos statistics View QoS statistics. Syntax Parameters show qos statistics {wred-profile [interface]} | [interface] wred-profile interface interface Enter the keywords wred-profile and optionally one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1693
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. show qos wred-profile View the WRED profile details. Syntax Parameters show qos wred-profile wred-profile-name wred-profilename Enter the WRED profile name to view the profile details. Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1694
wred_fortyg_g 25 467 4671 test cam-usage Check the Input Policy Map configuration for the CAM usage. Syntax Parameters test cam-usage service-policy input policy-map stack-unit {[number port-set portpipe number] | [all]} policy-map Enter the policy map name. stackunitnumber (OPTIONAL) Enter the keyword stack-unit then the stackunit slot number. port-set portpipe number Enter the keywords port-set then the stack-unit port pipe number. The range is from 0 or 1.
PAGE 1695
instance, the Estimated CAM output column contains the size of the CAM space required for the Trust rule and not the Class-map rule. The following describes the test cam-usage service-policy input policy-map stack-unit command shown in the following example. Field Description stack-unit Indicates the stack-unit slot number. Portpipe Indicates the portpipe number. CAM Partition The CAM space where the rules are added.
PAGE 1696
Exception 13 1 Allowed (2) Dell# … … … L2ACL 400 200 threshold Specify the minimum and maximum threshold values for the configured WRED profiles. Syntax threshold min number max number max-drop-probability To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360.
PAGE 1697
delete the threshold values of the pre-defined WRED profiles, the profiles revert to their original default values. Related Commands wred-profile — creates a WRED profile. trust Specify dynamic classification (DSCP) or dot1p to trust. Syntax Parameters trust {diffserv [fallback]| dot1p [fallback]} diffserv Enter the keyword diffserv to specify trust of DSCP markings. dot1p Enter the keyword dot1p to specify trust dot1p configuration.
PAGE 1698
DSCP/CP hex Range (XXX) DSCP Definition Traditional IP Precedenc e S6000 Internal Queue ID S-Series Internal Queue ID DSCP/CP Decimal 111XXX Network Control 7 3 48–63 110XXX Internetwo rk Control 6 3 48–63 101XXX EF (Expedited Forwarding ) CRITIC/EC P 5 2 32–47 100XXX AF4 (Assured Forwarding ) Flash Override 4 2 32–47 011XXX AF3 Flash 3 1 16–31 010XXX AF2 Immediate 2 1 16–31 001XXX AF1 Priority 1 0 0–15 000XXX BE (Best Effort) Best Effort 0 0 0–15 wred Des
PAGE 1699
Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_. Defaults When WRED green is applied, default WRED yellow profiles take effect and viceversa. Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 1700
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. When you enable wred ecn, and the number of packets in the queue is below the minimum threshold, packets are transmitted per the usual WRED treatment.
PAGE 1701
Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_g. Defaults The five pre-defined WRED profiles. When you configure a new profile, the minimum and maximum threshold defaults to predefined wred_ge_g values. If green profile is applied, default yellow also take effect and vice-versa. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1702
52 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell Networking operating software is supported on the platforms. Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell Networking OS private VLAN implementation is based on RFC 3069. For more information, refer to the following commands.
PAGE 1703
Port Types: • Community port: A community port is a port that belongs to a community VLAN and is allowed to communicate with other ports in the same community VLAN and with promiscuous ports. • Isolated port: An isolated port is a port that, in Layer 2, can only communicate with promiscuous ports that are in the same PVLAN. • Promiscuous port: A promiscuous port is a port that is allowed to communicate with any other port type.
PAGE 1704
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN. show arp — displays the ARP table.
PAGE 1705
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. The VLAN: • can be in only one mode, either community, isolated, or primary. • mode ode to community or isolated even before associating it to a primary VLAN.
PAGE 1706
Defaults none Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1707
• Command History Usage Information EXEC Privilege Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.1 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. This command has two types of display — a list of all PVLAN interfaces or for a specific interface. Examples of both types of output are shown below.
PAGE 1708
show vlan private-vlan Display PVLANs and/or interfaces that are part of a PVLAN. Syntax Parameters show vlan private-vlan [community | interface | isolated | primary | primary_vlan | interface interface] community (OPTIONAL) Enter the keyword community to display VLANs configured as community VLANs, along with their interfaces. interface (OPTIONAL) Enter the keyword interface to display VLANs configured as community VLANs, along with their interfaces.
PAGE 1709
Example (All) Field Description Primary Displays the VLAN ID of the designated or associated primary VLAN(s). Secondary Displays the VLAN ID of the designated or associated secondary VLAN(s). Type Displays the type of VLAN in which the listed interfaces reside. Active States whether the interface is operationally up or down. Ports Displays the interface IDs in the listed VLAN.
PAGE 1710
particular secondary VLAN properties are displayed, as shown in the second Example.
PAGE 1711
Example Dell# show vlan private-vlan mapping Private Vlan: Primary : 100 Isolated : 102 Community : 101 Unknown : 200 Related Commands private-vlan mode – sets the mode of the selected VLAN to community, isolated, or primary. show interfaces private-vlan – displays type and status of PVLAN interfaces. show vlan private-vlan mapping – displays the primary-secondary VLAN mapping. switchport mode private-vlan – sets PVLAN mode of the selected port.
PAGE 1712
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information The assignment of the various PVLAN port types to port and port channel (LAG) interfaces is shown in the following example.
PAGE 1713
Routing Information Protocol (RIP) 53 Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking operating software supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2) on the platform. The Dell Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, refer to the Dell Networking OS Configuration Guide.
PAGE 1714
clear ip rip Update all the RIP routes in the Dell Networking OS routing table. Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1715
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. database (OPTIONAL) Enter the keyword database to display messages when there is a change to the RIP database. events (OPTIONAL) Enter the keyword events to debug only RIP protocol changes.
PAGE 1716
To return to the default values, use the no default-information originate command. Parameters always (OPTIONAL) Enter the keyword always to enable the switch software to always advertise the default route. metric metricvalue (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 1 to 16. The default is 1. route-map map-name (OPTIONAL) Enter the keywords route-map then the name of a configured route-map. Defaults Disabled. Metric: 1.
PAGE 1717
To return the default metric to the original values, use the no default-metric command. Parameters number Specify a number. The range is from 1 to 16. The default is 1. Defaults 1 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 1718
Defaults none Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1719
prefix-name (OPTIONAL) Enter a configured prefix list name. Defaults weight = 120 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1720
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1721
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094.
PAGE 1722
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1723
Parameters 1 (OPTIONAL) Enter the number 1 for RIP version 1. 2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1724
2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1725
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 1726
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. RIP supports a maximum of 16 ECMP paths. neighbor Define a neighbor router with which to exchange RIP information.
PAGE 1727
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. When a neighbor router is identified, unicast data exchanges occur. Multiple neighbor routers are possible. To ensure that only specific interfaces are receiving and sending data, use the passive-interface command with the neighbor command. Related Commands passive-interface — sets the interface to only listen to RIP broadcasts.
PAGE 1728
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. You can enable an unlimited number of RIP networks. RIP operates over interfaces configured with any address the network command specifies. offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP.
PAGE 1729
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.
PAGE 1730
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command is intended for low-speed interfaces. passive-interface Suppress routing updates on a specified interface.
PAGE 1731
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1732
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To redistribute the default route (0.0.0.0/0), configure the default-information originate command.
PAGE 1733
Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1734
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1735
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable RIP, assign a network address using the network command. Example Dell(conf)#router rip Dell(conf-router_rip)# Related Commands network — enables RIP. exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration.
PAGE 1736
Example Version Description pre- 6.2.1.1 Introduced on the E-Series. Dell(conf-router_rip)#show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1 Dell(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Syntax Parameters show ip rip database [ip-address mask] ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only.
PAGE 1737
Usage Information Example The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24... Lists the routes and the sources advertising those routes.
PAGE 1738
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.
PAGE 1739
Defaults holddown Enter the number of seconds to specify a time interval during which the route is marked as unreachable but still sending RIP packets. The holddown value should be at least three times the update timer value. The range is from zero (0) to 4294967295. The default is 180 seconds. flush Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table.
PAGE 1740
version Specify either RIP version 1 or RIP version 2. Syntax version {1 | 2} To return to the default version setting, use the no version command. Parameters 1 Enter the keyword 1 to specify RIP version 1. 2 Enter the keyword 2 to specify RIP version 2. Defaults The Dell Networking OS sends RIPv1 and receives RIPv1 and RIPv2. Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1741
Remote Monitoring (RMON) 54 The Dell Networking operating software remote monitoring (RMON) is implemented on the platform. Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1742
Parameters number Enter the alarm integer number from 1 to 65535. The value must be unique in the RMON alarm table. variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3. The object type must be a 32-bit integer. interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables.
PAGE 1743
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on an interface.
PAGE 1744
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon collection statistics Enable RMON MIB statistics collection on an interface.
PAGE 1745
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table. Syntax rmon event number [log] [trap community] [description string] To disable RMON on an interface, use the no rmon event number command.
PAGE 1746
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1747
risingthreshold value event-number Enter the keywords rising-threshold then the value (64 bit) the rising-threshold alarm is either triggered or reset. Then enter the event-number to trigger when the rising threshold exceeds its limit. This value is the same as the alarmRisingEventIndex or alarmTable of the RMON MIB. If there is no corresponding rising-threshold event, the value is zero.
PAGE 1748
show rmon Display the RMON running status including the memory usage. Syntax show rmon Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1749
Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 1750
11 12 13 14 15 16 17 18 19 20 21 22 Dell# 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 1.3.6.1.2.1.1.3 show rmon events Display the contents of the RMON event table. Syntax Parameters show rmon events [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry.
PAGE 1751
Version Description 6.1.1.0 Introduced on the E-Series. Example (Index) Dell(conf)#rmon event 111 -> Dell(conf)#rmon event 112 log -> Dell(conf)#rmon event 113 trap private -> Dell(conf)#rmon event 114 log trap public-> “trap” options Dell(conf)#do show rmon events RMON event entry 111 description: event type: none. event community: event last time sent: none event owner: event status: OK RMON event entry 112 description: event type: LOG.
PAGE 1752
21 22 Dell# 21 22 show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. Syntax Parameters show rmon hc-alarm [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1753
alarm falling threshold value: positive. falling threshold: 999, RMON event index: 6 alarm sampling failed 0 times. alarm owner: 1 alarm storage type: non-volatile. alarm status: OK Dell# Example (Brief) Dell#show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 Dell# show rmon history Display the contents of the RMON Ethernet history table.
PAGE 1754
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1755
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The log table has a maximum of 500 entries.
PAGE 1756
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example (Index) 1756 Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1757
HC 512-1023 bytes packets: 0 HC 1024-1518 bytes packets overflow: 0 HC 1024-1518 bytes packets: 0 Dell# Example (Brief) Dell#show rmon statistics br index ifIndex interface ---------------------------------------6001 100974631 TenGigabitEthernet 2/2 6002 100974631 TenGigabitEthernet 2/2 6003 101236775 TenGigabitEthernet 2/1 6004 101236775 TenGigabitEthernet 2/1 9001 134529054 TenGigabitEthernet 3/2 9002 134529054 TenGigabitEthernet 3/2 9003 134791198 TenGigabitEthernet 3/1 9004 134791198 TenGigabitEthernet
PAGE 1758
Rapid Spanning Tree Protocol (RSTP) 55 The Dell Networking operating software implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking OS supports RSTP.. bridge-priority Set the bridge priority for RSTP.
PAGE 1759
Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disable debugging, use the no debug spanning-tree rstp command. Parameters all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu interface {in | out} (OPTIONAL) Enter the keyword bpdu to debug the bridge protocol data units.
PAGE 1760
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell#debug spanning-tree rstp bpdu tengigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree.
PAGE 1761
Related Commands Version Description 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific.
PAGE 1762
forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds that Dell Networking OS waits before transitioning RSTP to the forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1763
Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. milli-second Enter the keywords milli-second to configure a hello time on the order of milliseconds. The range is from 50 to 950 milliseconds Defaults 2 seconds Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific.
PAGE 1764
max-age To maintain configuration information before refreshing that information, set the time interval for the RSTP bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40 seconds. The default is 20 seconds.
PAGE 1765
Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1766
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell(conf-rstp)#show config ! protocol spanning-tree rstp no disable bridge-priority 16384 show spanning-tree rstp Display the RSTP configuration.
PAGE 1767
Usage Information Example (Brief) Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) caused by loopback BPDU inconsistency. 6.2.1.1 Introduced on the E-Series. The following describes the show spanning-tree rstp guard command shown in the following example. Field Description Interface Name RSTP interface. Instance RSTP instance.
PAGE 1768
- ---- ------- --- ------- -------------------- -------Te 1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge --- ------ -------- ---- ------- --- ------- --------- ---Te 1/1 ErrDis 128.257 128 20000 EDS 0 P2P No Dell#show spanning-tree rstp Root Identifier has priority 32768, Address 0001.e801.6aa8 Root Bridge hello time 2, max age 20, forward delay 15, max hops 0 Bridge Identifier has priority 32768, Address 0001.e801.
PAGE 1769
• Port Channel interface with one 10 Gigabit Ethernet = 2000 • Port Channel with two 1 Gigabit Ethernet = 18000 • Port Channel with two 10 Gigabit Ethernet = 1800 • Port Channel with two 100 Mbps Ethernet = 180000 edge-port Enter the keywords edge-port to configure the interface as a rapid spanning tree edge port. bpduguard (OPTIONAL) Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails.
PAGE 1770
Usage Information Version Description 8.2.1.0 Introduced the hardware shutdown-on-violation options. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the optional bridge port data unit (BPDU) guard. 6.2.1.1 Introduced on the E-Series. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack.
PAGE 1771
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled Command Modes CONFIGURATION (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1772
Software-Defined Networking (SDN) 56 Dell Networking operating software supports Software-Defined Networking (SDN). For more information, refer to the SDN Deployment Guide.
PAGE 1773
57 Security The commands in this chapter are available on Dell Networking OS. This chapter contains various types of security commands offered in the Dell Networking operating software. The commands are listed in the following sections: • AAA Accounting Commands • Authorization and Privilege Commands • Authentication and Password Commands • RADIUS Commands • TACACS+ Commands • Port Authentication (802.
PAGE 1774
Parameters system Enter the keyword system to send accounting information of any other AAA configuration. exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. commands {level | role role-name Enter the keyword command then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role.
PAGE 1775
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. In the example above, TACACS+ accounting is used to track all usage of EXEC command and commands on privilege level 15. Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command.
PAGE 1776
Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1777
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4280T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. Dell Networking OS issues accounting records for all users on the system, including users whose username string, due to protocol translation, is NULL.
PAGE 1778
If the RADIUS group is not configured for Authentication, Authorization, and Accounting, then globally configured Radius servers are used for the purposes. When the RADIUS group is removed, the AAA configuration is also removed. Example show accounting Display the active accounting sessions for each online user. Syntax show accounting Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1779
Related Commands aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. Authorization and Privilege Commands To set command line authorization and privilege levels, use the following commands. authorization Apply an authorization method list to terminal lines. Syntax Parameters authorization {exec | commands {level | role role-name}} method-list exec Enter the keyword exec to apply an EXEC level authorization method list.
PAGE 1780
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. aaa authorization commands — sets the parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands aaa authorization exec — sets the parameters that restrict (or permit) a user’s access to EXEC level commands.
PAGE 1781
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS.
PAGE 1782
Usage Information By default, the aaa authorization commands command configures the system to check both EXEC level and CONFIGURATION level commands. Use the command no aaa authorization config-commands to enable only EXEClevel command checking. aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands.
PAGE 1783
privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands. Syntax privilege mode {level level command | reset command} To delete access to a level and command, use the no privilege mode level level command command.
PAGE 1784
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines. Syntax privilege level level To delete access to a terminal line, use the no privilege level level command.
PAGE 1785
Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication, use the service obscurepasswords command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1786
Related Commands show running-config— Display the current configuration and display changes from the default values. service password-encryption— Encrypts all passwords configured in the system. Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Syntax aaa authentication enable {default | method-list-name} method [...
PAGE 1787
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 1788
To return to the default setting, use the no aaa authentication login {method-list-name | default} command. Parameters method-listname Enter a text string (up to 16 characters long) as the name of a user-configured method list that can be applied to different lines. default Enter the keyword default to specify that the method list specified is the default method for all terminal lines. method Enter one of the following methods: ...
PAGE 1789
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. By default, the locally configured username password is used. If you configure aaa authentication login default, Dell Networking OS uses the methods this command defines for login instead.
PAGE 1790
Parameters access-listname Enter the name of an established IP Standard ACL. Defaults Not configured. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1791
Enter a 7 then a text string as the hidden password. The text string must be a password that was already encrypted by a Dell Networking router. Use this parameter only with a password that you copied from the show running-config file of another Dell Networking router. password Enter a text string, up to 32 characters long, as the clear text password. Defaults No password is configured. level = 15. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1792
privilege level (CONFIGURATION mode) — controls access to the command modes within the switch. enable restricted Allows Dell Networking technical support to access restricted commands. Syntax enable restricted [encryption-type] password To disallow access to restricted commands, use the no enable restricted command. Parameters encryptiontype (OPTIONAL) Enter the number 7 as the encryption type. Enter 7 followed a text string as the hidden password.
PAGE 1793
enable secret Change the password for the enable command. Syntax enable secret [level level] [encryption-type] password To delete a password, use the no enable secret [encryption-type] password [level level] command. Parameters level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 to 15. encryptiontype (OPTIONAL) Enter the number 5 or 0 as the encryption type. Enter a 5 then a text string as the hidden password.
PAGE 1794
Usage Information To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: • Start with a letter, not a number. • Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression. For example, to create the password abcd]e, you type “abcd CNTL v ]e”.
PAGE 1795
Usage Information Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series.
PAGE 1796
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1797
Parameters min-length number (OPTIONAL) Enter the keywords min-length then the number of characters. The range is from 0 to 32 characters. max-retry number (OPTIONAL) Enter the keywords max-retry then the number of maximum password retries. The range is from 0 to 16. lockout-period minutes (OPTIONAL) Enter the keyword lockout-period then the number of minutes. The range is from 1 to 1440 minutes. The default is 0 minutes and the lockout-period is not enabled.
PAGE 1798
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. password — specifies a password for users on terminal lines. service password-encryption Encrypt all passwords configured in Dell Networking OS.
PAGE 1799
To keep unauthorized people from viewing passwords in the switch configuration file, use the service password-encryption command. This command encrypts the clear-text passwords created for user name passwords, authentication key passwords, the privileged command password, and console and virtual terminal line access passwords. To view passwords, use the show running-config command. show privilege View your access level.
PAGE 1800
show users Allows you to view information on all users logged in to the switch. Syntax Parameters show users [all] all (OPTIONAL) Enter the keyword all to view all terminal lines in the switch. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1801
Role Priv Host(s) * 0 console 0 unassigned 1 idle 2 vty 0 admin unassigned 1 idle 3 vty 1 ad unassigned 15 idle 4 vty 2 ad1 sysadmin 1 idle 5 vty 3 ad1 sysadmin 1 idle 6 vty 4 admin unassigned 1 idle 7 vty 5 ad unassigned 15 idle Dell# Related Commands Location 10.16.127.35 10.16.127.145 10.16.127.141 10.16.127.145 10.16.127.141 10.16.127.141 username — enables a user.
PAGE 1802
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The software measures the period of inactivity defined in this command as the period between consecutive keystrokes. For example, if your password is “password” you can enter “p” and wait 29 seconds to enter the next letter.
PAGE 1803
available with the secret option only, and is the default encryption type for this option. password Enter a string up to 32 characters long. privilege level Enter the keyword privilege then a number from zero (0) to 15. role role-name Enter the keyword role followed by the role name to associate with that user ID. secret Enter the keyword secret then the encryption type. Defaults The default encryption type for password option is 0. The default encryption type for secret option is 0.
PAGE 1804
RADIUS Commands The following RADIUS commands are supported by Dell Networking OS. debug radius View RADIUS transactions to assist with troubleshooting. Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1805
• For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. The range is from 1 to 128. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1806
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1807
! radius-server group group1 radius-server vrf vrf1 source-interface TenGigabitEthernet 1/36 radius-server host 1.1.1.1 key 7 9a2f3ec0c65c6f41 radius-server host 2.2.2.2 key 7 9a2f3ec0c65c6f41 Dell(conf-radius-group)# Related Commands login authentication — sets the database to be checked when a user logs in. radius-server key — sets an authentication key for RADIUS communications. radius-server retransmit — sets the number of times the RADIUS server attempts to send information.
PAGE 1808
• 0 is the default and means the password is not encrypted and stored as clear text. • 7 means that the password is encrypted and hidden. Configure this parameter last because leading spaces are ignored. Defaults Not configured. Command Modes • RADIUS SERVER GROUP • CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1809
that are configured in the CONFIGURATION mode are also considered to be on the default VRF. You must configure the RADIUS group explicitly with the aaa radius group command in order for the AAA servers to use the group of RADIUS servers. The 802.1x servers use the group of RADIUS servers based on the VRF where the 802.1x request is received.
PAGE 1810
• For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes RADIUS SERVER GROUP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1811
Parameters encryptiontype key (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the key is not encrypted and stored as clear text. • 7 means that the key is encrypted and hidden. Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 42 characters long. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1812
radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable. Syntax radius-server retransmit retries To configure zero retransmit attempts, use the no radius-server retransmit command. To return to the default setting, use the radius-server retransmit 3 command. Parameters retries Enter a number of attempts that FTOS tries to locate a RADIUS server. The range is from zero (0) to 100.
PAGE 1813
Parameters seconds Enter the number of seconds between an unsuccessful attempt and the Dell Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds. Defaults 5 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1814
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 1815
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections. Syntax ip tacacs source-interface interface To delete a source interface, use the no ip tacacs source-interface command.
PAGE 1816
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. tacacs-server group Creates a group of TACACS servers. Syntax tacacs-server group group-name To delete a group of TACACS servers, use the no tacacs-server group group-name command.
PAGE 1817
Related Commands aaa authentication login — specifies the login authentication method. tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server host Specify a TACACS+ host. Syntax Parameters tacacs-server host {hostname | ipv4-address | ipv6-address} [port number] [timeout seconds] [key key] hostname Enter the name of the TACACS+ server host. ipv4-address | ipv6-address Enter the IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the TACACS+ server host.
PAGE 1818
Usage Information Version Description 7.7.1.0 Authentication key length increased to 42 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times. If you are not configuring the switch as a TACACS+ server, you do not need to configure the port, timeout and key optional parameters.
PAGE 1819
key Enter a text string, up to 42 characters long, as the clear text password. Leading spaces are ignored. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 1820
• For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords portchannel then a number. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes TACACS SERVER GROUP Command History This guide is platform-specific.
PAGE 1821
port to which a client is connected. After authentication is successful, normal traffic passes through the port. Dell Networking OS supports RADIUS and Active Directory environments using 802.1X Port Authentication. Important Points to Remember Dell Networking OS limits network access for certain users by using VLAN assignments. 802.1X with VLAN assignment has these characteristics when configured on the switch and the RADIUS server. • 802.1X is supported on Dell Networking OS. • 802.
PAGE 1822
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x authentication (Interface) — enables dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface; dot1x must be enabled both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command.
PAGE 1823
Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094. max-attempts number (OPTIONAL) Enter the keywords max-attempts then number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1824
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.
PAGE 1825
Usage Information 802.1X authentication is enabled when an interface is connected to the switch. If the host fails to respond within a designated amount of time, the authenticator places the port in the guest VLAN. If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable. Therefore, a guest VLAN is allocated to the interface and authentication for the device occurs at the next re-authentication interval (dot1x reauthentication).
PAGE 1826
Usage Information Version Description 8.4.1.0 Introduced on the C-Series and S-Series. To disable MAC authentication bypass on a port, enter the no dot1x mac-authbypass command. dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command.
PAGE 1827
Parameters forceauthorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. forceunauthorized Enter the keywords force-unauthorized to forcibly deauthorize a port. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1828
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.
PAGE 1829
Related Commands Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. interface range — configures a range of interfaces. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2.
PAGE 1830
Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 1831
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs are transmitted by the Authenticator PAE. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command.
PAGE 1832
show dot1x interface Display the 802.1X information on an interface. Syntax Parameters show dot1x interface interface interface Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1833
Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Dell# NONE Disable Disable 30 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Initialize Initialize Dell# show dot1x interface fortyGigE 1/48 802.
PAGE 1834
Parameters rsa Enter the keyword rsa then the key size to generate a SSHv2 RSA host keys. The range is from 1024 to 2048 if you did not enable FIPS mode; if you enabled FIPS mode, you can only generate a 2048-bit key. The default is 1024. NOTE: You must have a license to access the FIPS mode. For more information, contact your Dell Networking representative. rsa1 Enter the keyword rsa1 then the key size to generate a SSHv1 RSA host keys. The range is from 1024 to 2048. The default is 1024.
PAGE 1835
Example Dell(conf)#crypto key generate rsa Enter key size <1024-2048>. Default<1024> : Host key already exists. Overwrite (y/n)?y Generating 1024-bit SSHv2 RSA key. ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Dell(conf)# Dell(conf)#crypto key generate rsa1 Enter key size <1024-2048>. Default<1024> : Host key already exists. Overwrite (y/n)?y Generating 1024-bit SSHv1 RSA key.
PAGE 1836
Parameters client Enter the keyword client to enable collecting debug information on the client. server Enter the keyword server to enable collecting debug information on the server. Defaults Disabled on both client and server. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1837
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To configure the switch as an SCP server, use the ip ssh server command. Related Commands ip ssh server — enables the SSH and SCP server on the switch.
PAGE 1838
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. This command specifies the maximum number of attempts to authenticate a user on an SSH connection with the remote host for password authentication. SSH disconnects when the number of password failures exceeds authentication-retries. ip ssh connection-rate-limit Configure the maximum number of incoming SSH connections per minute.
PAGE 1839
Parameters enable Enter the keyword enable to enable hostbasedauthentication for SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.
PAGE 1840
Defaults Key size 768 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1841
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. With password authentication enabled, you can authenticate using the local, RADIUS, or TACACS+ password fallback order as configured. ip ssh pub-key-file Specify the file used for host-based authentication.
PAGE 1842
command, it does not appear in the running configuration because you only need to run this command once. The file contains the OpenSSH-compatible public keys of the host for which hostbased authentication is allowed. An example known host file format: poclab4,123.12.1.
PAGE 1843
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL ip ssh rhostsfile Specify the rhost file used for host-based authorization. Syntax Parameters ip ssh rhostsfile {WORD} WORD Enter the rhost file name for the host-based authentication. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1844
NOTE: For rhostfile and pub-key-file, the administrator must FTP the file to the switch. ip ssh rsa-authentication (Config) Enable RSA authentication for the SSHv2 server. Syntax ip ssh rsa-authentication enable To disable RSA authentication, use the no ip ssh rsa-authentication enable command. Parameters enable Enter the keyword enable to enable RSA authentication for the SSHv2 server. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1845
ip ssh server Configure an SSH server. SSH server is enabled by default. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative.
PAGE 1846
The following HMAC algorithms are available: • hmac-sha1 • hmac-sha1-96 • hmac-sha2-256 • hmac-sha2-256-96 When FIPS is enabled, the default HMAC algorithm is hmacsha1-96. When FIPS is not enabled, the default HMAC algorithms are the following: kex keyexchangealgorithm • hmac-md5 • hmac-md5-96 • hmac-sha1 • hmac-sha1-96 • hmac-sha2-256 • hmac-sha2-256-96 Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server.
PAGE 1847
Defaults • Default listening port is 22. • Default cipher list is 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128ctr,aes192-ctr,aes256-ctr. • When FIPS is enabled, the default is hmac-sha1-96. • When FIPS is not enabled, the default is hmac-md5,hmac-md5-96,hmacsha1,hmac-sha1-96,hmac-sha2-256,hmac-sha2-256-96. • When FIPS is enabled, the default is diffie-hellman-group14-sha1.
PAGE 1848
ip ssh server vrf Configure an SSH server on either a specific VRF or a management VRF. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative. ip ssh server vrf {management | vrf-name} To disable the SSH server configuration, use the no ip ssh server vrf {management | vrf-name} command.
PAGE 1849
Related Commands show ip ssh — displays the ssh information. ip ssh source-interface Specifies an interface’s IP address as the source IP address for an outgoing SSH connections. Syntax ip ssh source-interface interface To delete a source interface, use the no ip ssh source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1850
Example Dell(conf)#ip ssh source-interface tengigabitethernet 1/42 Dell(conf)#do ssh 10.10.10.2 -l admin Dell(conf)#no ip ssh source-interface ip ssh vrf Specify a VRF for an outgoing SSH connections. Syntax ip ssh vrf vrf-name To delete a VRF for an outgoing SSH connection, use the no ip ssh vrf vrfname command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to configure that VRF for an outgoing SSH session. Defaults Not configured.
PAGE 1851
Parameters Key Enter the keyword key to display the host public key. mypubkey Enter the keyword mypubkey to display the host public key. rsa Enter the keyword rsa to display the host SSHv2 RSA public key. rsa1 Enter the keyword rsa1 to display the host SSHv1 RSA public key. NOTE: If you enable FIPS mode, this parameter is not available. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1852
Related Commands crypto key generate — generates the SSH keys. show ip ssh Display information about established SSH sessions. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative. show ip ssh Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1853
Related Commands ip ssh server — configures an SSH server. show ip ssh client-pub-keys — displays the client-public keys. show ip ssh client-pub-keys Display the client public keys used in host-based authentication. Syntax show ip ssh client-pub-keys Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1854
eFPaHiygd8U/FXict61jWs84Co1UTsAgRzDJ9aUSS75TVac= Dell# Related Commands ip ssh pub-key-file — configures the filename for the host-based authentication. show ip ssh rsa-authentication Display the authorized-keys for the RSA authentication. Syntax Parameters show ip ssh rsa-authentication {my-authorized-keys} myauthorizedkeys Display the RSA authorized keys. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1855
Related Commands ip ssh rsa-authentication (Config) — configures the RSA authorized keys. ssh Open an SSH connection specifying the hostname, username, encryption cipher, HMAC algorithm, port number, and version of the SSH client. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative.
PAGE 1856
• aes256-ctr : Force ssh to use aes256-ctr encryption cipher -l username (OPTIONAL) Enter the keyword -l then the user name used in this SSH session. The default is the user name of the user associated with the terminal. -m HMAC algorithm Enter one of the following HMAC algorithms to use. (For v2 clients only): "no fips mode enable"(disable) will support v1 & v2 client. • hmac-md5: Force ssh to use hmac-md5 HMAC algorithm. • hmac-md5-96: Force ssh to use hmac-md5-96 HMAC algorithm.
PAGE 1857
Usage Information Dell Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing. Inbound SSH supports accessing the system through the management interface as well as through a physical Layer 3 interface. Example Dell#ssh 10.16.151.48 -l anvltest Trying 10.16.151.48... 01:18:16: %STKUNIT0-M:CP %SEC-5-SSH_USAGE: Initiated SSH Client v2 (FIPS Disabled) to anvltest@10.16.151.48 by default from console anvltest@10.16.151.
PAGE 1858
ip dhcp relay Enable Option 82. Syntax Parameters ip dhcp relay information-option [trust-downstream trustdownstream Configure the system to trust Option 82 when it is received from the previous-hop router. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1859
Version Description 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information When enabled, no learning takes place until you enable snooping on a VLAN. After disabling DHCP Snooping, the binding table is deleted and Option 82, IP Source Guard, and Dynamic ARP Inspection are disabled. Related Commands ip dhcp snooping vlan — enables DHCP Snooping on one or more VLANs. ip dhcp snooping binding Create a static entry in the DHCP binding table.
PAGE 1860
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp snooping database Delay writing the binding table for a specified time.
PAGE 1861
Defaults none Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1862
ip dhcp source-address-validation Enable IP source guard. Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1863
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. When enabled, the system begins creating entries in the binding table for the specified VLANs. NOTE: Learning only happens if there is a trusted port in the VLAN. Related Commands ip dhcp snooping trust — configures an interface as trusted. show ip dhcp snooping Display the contents of the DHCP binding table.
PAGE 1864
created for job functions and through those roles they acquire the permissions to perform their associated job function. This section describes the syntax and usage of RBAC-specific commands.
PAGE 1865
Related Commands 1. Locally define a system administrator user role.This will give you access to login with full permissions even if network connectivity to remote authentication servers is not available. 2. Configure login authentication on the console. This ensures that all users are properly identified through authentication no matter the access point 3. Specify an authentication method (RADIUS, TACACS+, or Local). 4. Specify authorization method (RADIUS, TACACS+ or Local). 5.
PAGE 1866
Usage Information Version Description E-Series Original command. Users entering EXEC Privilege mode or any other configured privilege level can access configuration commands. To protect against unauthorized access, use the enable password command to configure a password for the enable command at a specific privilege level. If no privilege level is specified, the default is privilege level 15.
PAGE 1867
reset Enter the keyword reset to reset all roles back to default for that command. command Enter the command’s keywords to assign the command to a certain access level. You can enter one or more keywords. Defaults none Command Modes CONFIGURATION Command History Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, and MXL.
PAGE 1868
Dell#show role mode configure management route Role access: netadmin, sysadmin Dell#show role mode configure management crypto-policy Role access: secadmin, sysadmin Related Commands userrole, username, privilege show userroles Display information on all defined user roles.
PAGE 1869
Defaults none Command Modes CONFIGURATION Command History Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization. When you create a new user role, you first inherit permissions from one of the system defined roles. Otherwise you would have to create a user role from scratch.
PAGE 1870
58 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command line information (CLI) for the Dell Networking operating software Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel.
PAGE 1871
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a Port Channel interface, enter the keywords portchannel then a number. The range is from 1 to 128.
PAGE 1872
To disable protocol tunneling for a Layer 2 protocol, use the no protocoltunnel command. Parameters rate-limit rate Enter the keyword rate-limit followed by a number for the rate-limit for tunneled packets on the VMAN. The range is from 64 to 320. stp Enter the keyword stp to enable protocol tunneling on a spanning tree, including STP, MSTP, RSTP, and PVST. Defaults none Command Modes CONF-IF-VLAN Command History This guide is platform-specific.
PAGE 1873
Parameters stp Change the default destination MAC address used for L2PT to another value. Defaults The default destination MAC is 01:01:e8:00:00:00. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1874
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.4.1.0 Introduced Dell Networking OS must have the default CAM profile with the default microcode before you enable L2PT. protocol-tunnel rate-limit Enable traffic rate limiting per box.
PAGE 1875
Version Description 7.4.1.0 Introduced Example Dell# Dell#conf Dell(conf)#protocol-tunnel rate-limit 1000 Dell(conf)# Related Commands show protocol-tunnel — displays tunneling information for all VLANs. show running-config — displays the current configuration. show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN.
PAGE 1876
1001 1002 1003 1004 1005 LLDP,GVRP MMRP,MVRP LACP,DOT1X OAM,PAUSE E-LMI Te Te Te Te Te 5/7,Te 5/7,Te 5/7,Te 5/7,Te 5/7,Te 5/6 5/6 5/6 5/6 5/6 Example (Specific VLAN) Dell#show protocol-tunnel vlan 2 System Rate-Limit: 1000 Frames/second Interface Vlan Protocol(s) Te1/2 2 STP, PVST Dell# Related Commands show running-config — displays the current configuration.
PAGE 1877
sFlow 59 The Dell Networking operating software (OS) supports sFlow commands on Dell Networking OS. Dell Networking operating software sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1878
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ipaddress | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
PAGE 1879
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.3 Added support for IPv6 sFlow collectors and agents on the E-series TeraScale, C-Series, and S-Series. 8.4.1.1 Added support for IPv6 sFlow collectors and agents on the E-series ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.
PAGE 1880
sflow enable (Global) Enable sFlow globally. Syntax sflow enable To disable sFlow, use the no sflow enable command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 1881
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced on the S-Series, Z-Series, and MXL switch.
PAGE 1882
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1883
Example Version Description 9.7(0.0) Introduced on the S Series and Z Series switches. Dell(conf)#sflow max-header-size extended sflow polling-interval (Global) Set the sFlow polling interval at a global level. Syntax sflow polling-interval interval value To return to the default, use the no sflow polling-interval interval command. Parameters interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is 20 seconds.
PAGE 1884
Related Commands sflow polling-interval (Interface) — sets the polling interval for an interface. sflow polling-interval (Interface) Set the sFlow polling interval at an interface (overrides the global-level setting.) Syntax sflow polling-interval interval value To return to the default, use the no sflow polling-interval interval command. Parameters interval value Enter the interval value in seconds. The range is from 15 to 86400 seconds. The default is the global counter polling interval.
PAGE 1885
sflow sample-rate (Global) Change the global default sampling rate. Syntax sflow sample-rate value To return to the default sampling rate, use the no sflow sample-rate command. Parameters value Enter the sampling rate value. For the C-Series and S-Series, the range is from 256 to 8388608 packets Enter values in powers of 2 only; for example, 4096, 8192, 16384, and so on. The default is 32768 packets.
PAGE 1886
sflow sample-rate (Interface) Change the interface default sampling rate. Syntax sflow sample-rate value To return to the default sampling rate, use the no sflow sample-rate command. Parameters value Enter the sampling rate value. For the C-Series and S-Series, the range is from 256 to 8388608 packets. Enter values in powers of 2 only; for example, 4096, 8192, 16384, etc. The default is 32768 packets. Defaults The Global default sampling.
PAGE 1887
show sflow Display the current sFlow configuration. Syntax Parameters show sflow [interface] interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1888
Usage Information The dropEvent counter (sFlow samples dropped due to sub-sampling) shown in the following example always displays a value of zero. Example Dell#show sflow sFlow services are enabled Egress Management Interface sFlow services are disabled Global default sampling rate: 32768 Global default counter polling interval: 20 Global default extended maximum header size: 128 bytes Global extended information enabled: none 1 collectors configured Collector IP addr: 100.1.1.1, Agent IP addr: 1.1.1.
PAGE 1889
UDP packets dropped Dell# sFlow :0 1889
PAGE 1890
60 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell Networking OS. The chapter contains the following sections: • SNMP Commands • Syslog Commands SNMP Commands The following SNMP commands are available in the Dell Networking OS.
PAGE 1891
show snmp Display the status of SNMP network elements. Syntax show snmp Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1892
show snmp engineID Display the identification of the local SNMP engine and all remote engines that are configured on the router. Syntax show snmp engineID Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON.
PAGE 1893
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1894
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1895
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. unknown Introduced on the E-Series. Dell#config!------command run on host connected to switch: --------------! > snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2. This is a port connected to IF-MIB::ifAlias.
PAGE 1896
rw Enter the keyword rw to specify read-write permission. ipv6 accesslist-name (Optional) Enter the keyword ipv6 then an IPv6 ACL name (a string up to 16 characters long). security-name name (Optional) Enter the keywords security-name then the security name as defined by the community MIB. access-listname (Optional) Enter a standard IPv4 access list name (a string up to 16 characters long). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1897
If you do not configure the snmp-server community command, you cannot query SNMP data. Only Standard IPv4 ACL and IPv6 ACL is supported in the optional access-list-name. The command options ipv6, security-name, and access-list-name are recursive. In other words, each option can, in turn, accept any of the three options as a sub-option, and each of those sub-options can accept any of the three suboptions as a sub-option, and so forth.
PAGE 1898
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1899
• notificationoption vlt — Notification of virtual link trunking. • vrrp — Notification of a state change in a VRRP group. • xstp — Notification of a state change in MSTP (802.1s), RSTP (802.1w), and PVST+. For the envmon notification-type, enter one of the following optional parameters: • cam-utilization • fan • supply • temperature For the snmp notification-type, enter one of the following optional parameters: • authentication • coldstart • linkdown • linkup Defaults Not enabled.
PAGE 1900
Version Description E-Series legacy command Usage Information Dell Networking OS supports up to 16 SNMP trap receivers. If you do not configure this command, no traps controlled by this command are sent. If you do not specify a notification-type and notification-option, all traps are enabled. Related Commands snmp-server community — enables SNMP and sets the community string. snmp-server engineID Configure the name for both the local and remote SNMP engines on the router.
PAGE 1901
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Changing the value of the SNMP Engine ID has important side effects.
PAGE 1902
Parameters group_name 1 | 2c | 3 Enter a text string (up to 20 characters long) as the name of the group. The following groups are created for mapping to read/write community/security-names (defaults): • v1v2creadg — maps to a community/security-name with ro permissions. • 1v2cwriteg — maps to a community/security-name rw permissions. (OPTIONAL) Enter the security model version number (1, 2c, or 3): • 1 is the least secure version. • 3 is the most secure of the security modes.
PAGE 1903
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.2 Added support for the access parameter. 8.3.7.
PAGE 1904
[community-string] [udp-port number] [notification-type] command. Parameters ip-address Enter the keyword host then the IP address of the host (configurable hosts is limited to 16). ipv6-address Enter the keyword host then the IPv6 address of the host in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zero. traps (OPTIONAL) Enter the keyword traps to send trap notifications to the specified host. The default is traps.
PAGE 1905
notificationtype (OPTIONAL) Enter one of the following keywords for the type of trap to be sent to the host: • bgp — Enable BGP state change traps. • ecfm — Enable ECFM state change traps. • entity — Enable entity change traps. • envmon — Enable SNMP environmental monitor traps. • eoam — Enable EOAM state change traps • ets — Enable ets traps • fips — Enable FIP Snooping state change traps • lacp — Enable LACP state change traps.
PAGE 1906
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information In order to configure the router to send SNMP notifications, enter at least one snmp-server host command. If you enter the command with no keywords, all trap types are enabled for the host. If you do not enter an snmp-server host command, no notifications are sent. In order to enable multiple hosts, issue a separate snmp-server host command for each host.
PAGE 1907
snmp-server location Configure the location of the SNMP server. Syntax snmp-server location text To delete the SNMP location, use the no snmp-server location command. Parameters text Enter an alpha-numeric text string, up to 55 characters long. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1908
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1909
Defaults The IP address assigned to the management interface is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1910
Parameters name Enter the name of the user (not to exceed 20 characters), on the host that connects to the agent. group_name Enter a text string (up to 20 characters long) as the name of the group. The following groups are created for mapping to read/write community/security-names (defaults): • v1v2creadu — maps to a community with ro permissions. • 1v2cwriteu — maps to a community rw permissions.
PAGE 1911
• aes128 — Use 128 bit AES algorithm in CFB mode for encryption. • des56 — Use 56 bit DES algorithm in CBC mode for encryption. priv password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the host to encrypt the contents of the message it sends to the agent. Minimum: eight characters long. access accesslist-name (Optional) Enter the standard IPv4 access list name (a string up to 16 characters long).
PAGE 1912
text password. In either case, the password is stored in the configuration in an encrypted form and displayed as encrypted in the show running-config command. If you have an encrypted password, you can specify the encrypted string instead of the plain-text password. The following command is an Example of how to specify the command with an encrypted string. NOTE: The number of configurable users is limited to 16.
PAGE 1913
aes128–cfb} priv-password] [access access-list-name | ipv6 access-list-name | access-list-name ipv6 access-list-name] command. Parameters auth-password (OPTIONAL) Enter a text string (up to 20 characters long) password that enables the agent to receive packets from the host and to send packets to the host. Minimum: eight characters long. aes128 (OPTIONAL) Enter the keyword aes128 to initiate the AES128-CFB encryption algorithm for transmission of SNMP packets.
PAGE 1914
snmp-server view Configure an SNMPv3 view. Syntax snmp-server view view-name oid-tree {included | excluded} To remove an SNMPv3 view, use the no snmp-server view view-name oidtree {included | excluded} command. Parameters view-name Enter the name of the view (not to exceed 20 characters). oid-tree Enter the OID sub tree for the view (not to exceed 20 characters). included (OPTIONAL) Enter the keyword included to include the MIB family in the view.
PAGE 1915
Related Commands show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF. Syntax snmp-server vrf vrf-name To undo the SNMP agent configuration, use the no snmp-server vrf vrfname command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate an SNMP agent with that VRF. Defaults Not Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1916
Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.
PAGE 1917
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1918
Version Description E-Series legacy command Related Commands logging buffered — sets the logging buffered parameters. default logging console Return the default settings for messages logged to the console. Syntax default logging console Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1919
Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1920
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands logging trap — limit messages logged to the Syslog servers based on severity. logging Configure an IP address or host name of a Syslog server where logging messages are sent. Multiple logging servers of both IPv4 and/or IPv6 can be configured.
PAGE 1921
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added udp and tcp keywords for the S4810, S4820T, S6000, Z9000, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for IPv6. 7.6.1.0 Introduced on the S-Series. 7.5.
PAGE 1922
size (OPTIONAL) Indicate the size, in bytes, of the logging buffer. The number of messages buffered depends on the size of each message. The range is from 40960 to 524288. The default is 40960 bytes. Defaults level = 7; size = 40960 bytes Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1923
logging console Specify which messages are logged to the console. Syntax logging console [level] To return to the default values, use the default logging console command. To disable logging to the console, use the no logging console command. Parameters level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1924
logging facility Configure the Syslog facility used for error messages sent to Syslog servers. Syntax logging facility [facility-type] To return to the default values, use the no logging facility command.
PAGE 1925
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands logging — enables logging to a Syslog server. logging on — enables logging.
PAGE 1926
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network management station. Related Commands show logging — displays information logged to the history buffer.
PAGE 1927
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When the number of messages reach the limit you set with the logging history size command, older messages are deleted as newer ones are added to the table. Related Commands show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications.
PAGE 1928
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands default logging monitor — returns the logging monitor parameters to the default setting. logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines.
PAGE 1929
Related Commands logging — enables logging to the Syslog server. logging buffered — sets the logging buffered parameters. logging console — sets the logging console parameters. logging monitor — sets the logging parameters for the terminal connections. logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server.
PAGE 1930
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1931
Defaults Disabled. If enabled without the level or number-of-buffers options specified, level = 2 and number-of-buffers = 20 are the defaults. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 1932
warnings, notifications, informational, or debugging. The default is 6 or informational. Defaults 6 or informational Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1933
summary Command Modes Command History • • (OPTIONAL) Enter the keyword summary to view a table showing the number of messages per type and per slot. Slots *7* and *8* represent RPMs. EXEC EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(0.
PAGE 1934
Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.1.1.12 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.1.1.15 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.200.12.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: neighbor 1.1.10.2 (Hold time expired) Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: 192.200.14.
PAGE 1935
terminal monitor Configure the Dell Networking OS to display messages on the monitor/terminal. Syntax terminal monitor To return to default settings, use the terminal no monitor command. defaults Disabled. Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1936
61 Spanning Tree Protocol (STP) The commands in this chapter configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell Networking switch/routing platform. bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree. Syntax bridge-priority {priority-value | primary | secondary} To return to the default value, use the no bridge-priority command. Parameters priority-value Enter a number as the bridge priority value.
PAGE 1937
Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. debug spanning-tree Enable debugging of the spanning tree protocol and view information on the protocol. Syntax debug spanning-tree {stp-id [all | bpdu | config | events | exceptions | general | root] | protocol} To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0.
PAGE 1938
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information When you enable debug spanning-tree bpdu for multiple interfaces, the software only sends information on BPDUs for the last interface specified. Related Commands protocol spanning-tree — enters SPANNING TREE mode on the switch.
PAGE 1939
Related Commands Version Description 7.7.1.0 Introduced protocol spanning-tree — enters SPANNING TREE mode on the switch. disable Disable the spanning tree protocol globally on the switch. Syntax disable To enable Spanning Tree Protocol, use the no disable command. Defaults Enabled (that is, the spanning tree protocol is disabled.) Command Modes SPANNING TREE Command History This guide is platform-specific.
PAGE 1940
forward-delay The amount of time the interface waits in the Listening state and the Learning state before transitioning to the Forwarding state. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds the Dell Networking OS waits before transitioning STP to the Forwarding state. The range is from 4 to 30. The default is 15 seconds.
PAGE 1941
Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10. The default is 2 seconds. Defaults 2 seconds Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.
PAGE 1942
Defaults 20 seconds Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1943
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information STP is not enabled when you enter SPANNING TREE mode.
PAGE 1944
Example Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell(config-stp)#show config protocol spanning-tree 0 no disable Dell(config-stp)# show spanning-tree 0 Display the spanning tree group configuration and status of interfaces in the spanning tree group.
PAGE 1945
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 1946
Field Example Description • notification • aging “Port 1...” Displays the Interface type slot/port information and the status of the interface (Disabled or Enabled). “Port path...” Displays the path cost, priority, and identifier for the interface. “Designated root...” Displays the priority and MAC address of the root bridge of the STG that the interface belongs. “Designated port...” Displays the designated port ID.
PAGE 1947
Dell# Example (Brief) Dell#show span 0 brief Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768 Address 0001.e800.0a56 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32768, Address 0001.e800.0a56 Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID -------------- ------ ---- ---- --- ----- -----------------Te 1/1 8.26 8 4 FWD 0 32768 0001.e800.0a56 8.26 Te 1/2 8.27 8 4 FWD 0 32768 0001.
PAGE 1948
Parameters stp-id Enter the STP instance ID. The range is 0. cost cost Enter the keyword cost followed by a number as the cost. The range is 1 to 65535. The defaults are: • 100 Mb/s Ethernet interface = 19. • 1-Gigabit Ethernet interface = 4. • 10-Gigabit Ethernet interface = 2. • Port Channel interface with 100 Mb/s Ethernet = 18. • Port Channel interface with 1-Gigabit Ethernet = 3. • Port Channel interface with 10-Gigabit Ethernet = 1.
PAGE 1949
Version 6.2.1.1 Usage Information Introduced on the E-Series. If you enable portfast bpduguard on an interface and the interface receives a BPDU, the software disables the interface and sends a message stating that fact. The port is in ERR_DISABLE mode, yet appears in the show interface commands as enabled. If you do not enable shutdown-on-violation, BPDUs still are sent to the RPM CPU.
PAGE 1950
62 Stacking Commands All commands in this chapter are specific to the Dell Networking OS on the S5000 switch. The commands are always available and operational. You can use the commands to pre-configure a switch so that the configuration settings are invoked when the switch is attached to other S5000 units. For information about using the S5000 stacking feature, refer to the Stacking chapter in the Dell Networking OS Configuration Guide for the S5000.
PAGE 1951
redundancy force-failover stack-unit Force the standby unit in the stack to become the management unit. Syntax Parameters redundancy force-failover stack-unit stack-unit Enter the stack unit. Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1952
Usage Information Version Description 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the hard reset option. Resetting the management unit is not allowed, and an error message displays if you try to do so. Resetting is a soft reboot, including flushing the forwarding tables. Starting with Dell Networking OS version 7.8.1.
PAGE 1953
• find — search for the first occurrence of a pattern. • grep — show only text that matches a pattern. • no-more — do not paginate the output. • save — save the output to a file. Example show system stack-ports Display information about the stacking ports on all switches in the stack. Syntax Parameters show system stack-ports [status | topology] status (OPTIONAL) Enter the keyword status to display the command output without the Connection field.
PAGE 1954
Field Description Admin Status The only currently listed status is Up. Connection The stack port ID to which this unit’s stack port is connected. Example Example (Status) Example (Topology) Related Commands • reset stack-unit – resets the designated stack member. • show hardware stack-unit – displays the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 1955
stack-unit priority Configure the ability of a switch to become the management unit of a stack. Syntax Parameters stack-unit stack-unit number priority 1-14 stack-number Enter the stack member unit identifier. 1–14 This preference parameter allows you to specify the management priority of one backup switch over another, with 0 the lowest priority and 14 the highest.
PAGE 1956
Command Modes Command History Usage Information EXEC Privilege Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. You can renumber any switch, including the management unit or a stand-alone unit. You cannot renumber a unit to a number of an active member in the stack. When executing this command on the master, the stack reloads.
PAGE 1957
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.1 Introduced on the S4810. 8.3.12.0 Reset command mode from EXEC to CONFIGURATION.
PAGE 1958
flash: After the keyword flash:, enter the location of the source file in the internal flash in the format: //file-pathname or press Enter to launch a prompt sequence. ftp: After the keyword ftp:, enter the location of the source file in the format: //userid:password@host-ip-address/ file-pathname or press Enter to launch a prompt sequence. tftp: After the keyword tftp:, enter the location of the source file in the format: //host-ipaddress/file—pathname or press Enter to launch a prompt sequence.
PAGE 1959
Dell#upgrade boot bootflash-image stack-unit all booted Current BootFlash information in the system: ============================================================== Card BootFlash Current Version New Version -------------------------------------------------------------Unit0 Boot Flash B 1.3.1.1o 1.3.1.1p Unit7 Boot Flash B 1.3.1.1o 1.3.1.1p Unit8 Boot Flash A 1.3.1.1o 1.3.1.1p Unit9 Boot Flash A 1.3.1.1o 1.3.1.
PAGE 1960
upgrade system (stack unit) Upgrade the Dell Networking OS image on one or all stack units in an S5000 stack from the master switch. S5000 Syntax Parameters upgrade system {flash://file-path | ftp://file-path | scp:// file-path | tftp://file-path | usbflash://file-path} | stackunit {stack-unit—id | all}{A: | B:}} boot Enter the keyword system to change the Dell Networking OS image.
PAGE 1961
Usage Information You must reload Dell Networking OS after executing this command. Use the upgrade system stack-unit command to copy Dell Networking OS from the management unit to one or more stack members.
PAGE 1962
Storm Control 63 The Dell Networking operating software storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and SSeries). Storm control is supported on Dell Networking OS. Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1963
show storm-control broadcast Display the storm control broadcast configuration. Syntax Parameters show storm-control broadcast [interface] interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: • Defaults none Command Modes • EXEC • EXEC Privilege Command History For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. This guide is platform-specific.
PAGE 1964
Defaults none Command Modes • EXEC • EXEC Privilege Command History • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. This guide is platform-specific.
PAGE 1965
Defaults none Command Modes • EXEC • EXEC Privilege Command History • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a port channel interface, enter the keywords portchannel then a number. This guide is platform-specific.
PAGE 1966
Parameters percentagedeci mal_value in | out Enter the percentage of broadcast traffic allowed in or out of the network. Optionally, you can designate a decimal value percentage, for example, 55.5%. The decimal range is from .1 to .9. wred-profile name Enter the keyword wred-profile followed by the profile name to designate a wred-profile. packets_per_se cond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1967
Parameters packets_per_se cond in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 1968
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.
PAGE 1969
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. storm-control unknown-unicast (Configuration) Configure the percentage of unknown-unicast traffic allowed in or out of the network.
PAGE 1970
Usage Information Version Description 6.5.1.0 Introduced on the E-Series. Unknown Unicast Storm-Control is valid for Layer 2 and Layer 2/Layer 3 interfaces. storm-control unknown-unicast (Interface) Configure percentage of unknown-unicast traffic allowed on an interface (ingress only).
PAGE 1971
Storm Control Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.0 Introduced on the E-Series.
PAGE 1972
System Time and Date 64 The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, refer to the “Network Time Protocol” section of the Management chapter in the Dell Networking OS Configuration Guide.
PAGE 1973
end-month Enter the name of one of the 12 months in English. You can enter the name of a day to change the order of the display to time day month year. end-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-year Enter a four-digit number as the year. The range is from 1993 to 2035. offset (OPTIONAL) Enter the number of minutes to add during the summer-time period. The range is from 1 to1440. The default is 60 minutes.
PAGE 1974
To delete a daylight saving time zone configuration, use the no clock summertime command. Parameters 1974 time-zone Enter the three-letter name for the time zone. This name is displayed in the show clock output. You can enter up to eight characters. start-week (OPTIONAL) Enter one of the following as the week that daylight saving begins and then enter values for start-day through end-time: • week-number: Enter a number from 1 to 4 as the number of the week in the month to start daylight saving time.
PAGE 1975
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1976
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 1977
events Enter the keyword events to display information on NTP events. loopfilter Enter the keyword loopfilter to display information on NTP local clock frequency. packets Enter the keyword packets to display information on NTP packets. select Enter the keyword select to display information on the NTP clock selection. sync Enter the keyword sync to display information on the NTP clock synchronization. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1978
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 1979
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Added options [0 | 7] for entering the authentication key. 7.6.1.
PAGE 1980
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 1981
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp multicast client To receive NTP information from the network via multicast, configure the switch. Syntax ntp multicast client [multicast-address] To disable multicast reception, use the no ntp multicast client [multicast-address] command. Parameters multicastaddress (OPTIONAL) Enter a multicast address.
PAGE 1982
ntp master Configure the switch as NTP Server. Syntax Parameters ntp master ntp master Enter the stratum number to identify the NTP Server's hierarchy. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1983
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added support for VRF. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.11.
PAGE 1984
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a Port Channel interface, enter the keyword lag then a number. The range is from 1 to 128. • For VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1985
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1986
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example Dell#show clock 11:05:56.949 UTC Thu Oct 25 2001 Dell# Example (Detail) Dell#show clock detail 12:18:10.
PAGE 1987
Usage Information Example System Time and Date Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp associations command shown in the Example below. Field Description (none) One or more of the following symbols could be displayed: • * means synchronized to this peer. • # means almost synchronized to this peer.
PAGE 1988
Related Commands show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. EXEC Privilege The following is a list of the Dell Networking OS version history for this command.
PAGE 1989
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. The following describes the show ntp status command shown in the Example below. Field Description “Clock is...
PAGE 1990
65 u-Boot All commands in this chapter are in u-Boot and are supported on the Dell Networking OS for S5000 platform. To access this mode, press any key when the following line appears on the console during a system boot: Hit any key to stop autoboot: You enter u-Boot immediately, as indicated by the => prompt. NOTE: This chapter describes only a few commands available in u-Boot. NOTE: You cannot use the Tab key to complete commands in this mode.
PAGE 1991
$filesize; erase 0x fff80000 +$filesize; cp.b $loadaddr 0xfff80000 $filesize; protect on 0xfff80000 +$filesize; cmp.b $loadaddr 0xfff80000 $filesize ethact=eTSEC1 ethaddr=00:01:E8:82:09:B2 serverip=10.11.9.4 primary_boot=f10boot tftp://10.11.9.2/si-S4810-40g secondary_boot=f10boot flash0 default_boot=f10boot tftp://192.168.128.1/FTOS-SC-1.2.0.0E3.bin gatewayip=10.11.192.254 ipaddr=10.11.198.114 netmask=255.255.0.
PAGE 1992
Usage Information You must save your changes before resetting the system or all your changes will be lost. save Save configurations created in uBoot. S5000 Syntax save Command Modes uBoot Command History Usage Information Version 9.0(1.0) Introduced on the S5000. You must save your changes before resetting the system or all your changes will be lost. syntax help Display command syntax information. S5000 Syntax syntax help Command Modes BOOT USER Command History Example Version 9.0(1.
PAGE 1993
zero operating system boot parameters default-gateway default-gateway - set the default gateway ip address enable [user|admin] change access privilege level help display help menu ignore enable-password ignore enable password ignore startup-config ignore system starup-config interface management ethernet ip address set the management port ip address and mask interface management port config 1000m set the management port at 1000m interface management port config 100m set the management port at 100m interface
PAGE 1994
boot selection Set the bootflash partition to be used for a ROM bootstrap operation. S5000 Syntax boot selection {a | b} Command Modes uBoot Command History 1994 Version 9.0(1.0) Introduced on the S5000.
PAGE 1995
Uplink Failure Detection (UFD) 66 Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link. clear ufd-disable Re-enable one or more downstream interfaces on the switch/router that are in a UFD-Disabled Error state so that an interface can send and receive traffic.
PAGE 1996
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. debug uplink-state-group Enable debug messages for events related to a specified uplink-state group or all groups.
PAGE 1997
description Enter a text description of an uplink-state group. Syntax Parameters description text text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. Defaults none Command Modes UPLINK-STATE-GROUP Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Command History This guide is platform-specific.
PAGE 1998
• 40-Gigabit Ethernet:fortyGigE {slot/port} • Port channel: port-channel {1–128 | portchannel-range} Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and portrange entry. Defaults none Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific.
PAGE 1999
downstream auto-recover Enable auto-recovery so that UFD-disabled downstream ports in an uplink-state group automatically come up when a disabled upstream port in the group comes back up. Syntax downstream auto-recover To disable auto-recovery on downstream links, use the no downstream autorecover command. Defaults The auto-recovery of UFD-disabled downstream ports is enabled. Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific.
PAGE 2000
Defaults No downstream links are disabled when an upstream link in an uplink-state group goes down. Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 2001
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links.
PAGE 2002
downstream TenGigabitEthernet upstream FortygigabitEthernet upstream PortChannel 1 ! uplink state track 2 downstream TenGigabitEthernet upstream FortygigabitEthernet Related Commands 1/2,4,6,11-19 1/27, 29 1/1,3,5,7-10 1/31,42 • show uplink-state-group — displays the status information on a specified uplink-state group or all groups. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links.
PAGE 2003
Uplink State Group: 7 Status: Enabled, Up Uplink State Group: 16 Status: Disabled, Up Dell# show uplink-state-group 16 Uplink State Group: 16 Status: Disabled, Up Dell#show uplink-state-group detail (Up): Interface up (Dwn): Interface down (Dis): Interface disabled Uplink State Group : 1 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 3 Status: Enabled, Up Upstream Interfaces : Te 1/25(Up) Te 1/28(Up) Downstream Interfaces : Te 5/1(Up) Te 5/1(Up) Te 5/3(Up) Te 5/5(Up)
PAGE 2004
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.
PAGE 2005
Parameters interface Enter one of the following interface types: • 10 Gigabit Ethernet: tengigabitethernet {slot/ port | slot/port-range} • 40-Gigabit Ethernet:fortyGigE {slot/port} • Port channel: port-channel {1–128 | portchannel-range} Where port-range and port-channel-range specify a range of ports separated by a dash (-) and/or individual ports/port channels in any order; for example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5.
PAGE 2006
Related Commands 2006 • downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links.
PAGE 2007
VLAN Stacking 67 With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell Networking operating software supports this feature on Dell Networking OS. For more information about basic VLAN commands, refer to the Virtual LAN (VLAN) Commands section in the Layer 2 chapter.
PAGE 2008
dei enable Make packets eligible for dropping based on their DEI value. Syntax dei enable Defaults Packets are colored green; no packets are dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.
PAGE 2009
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series.
PAGE 2010
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Instroduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information You must first enable DEI for this configuration to take effect. Related Commands dei enable – Make packets eligible for dropping based on their DEI value. member Assign a stackable VLAN access or trunk port to a VLAN.
PAGE 2011
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series and S-Series. Usage Information You must enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. Related Commands vlan-stack compatible — enables stackable VLAN on a VLAN.
PAGE 2012
Related Commands dei honor — Honor the incoming DEI value by mapping it to an Dell Networking OS drop precedence. show interface dei-mark Display the dei mark configuration. Syntax Parameters Command Modes Command History Example show interface dei-mark [interface slot/port | linecard number port-set number] interface slot/ port Enter the interface type followed by the line card slot and port number.
PAGE 2013
stack-unit stack-group Configure a stacking group specified by an ID. Syntax Parameters [no] stack-unit unit-id stack-group stack-group-id unit-id Enter the stack unit ID. stack-group-id Enter the stack group ID. The range is from 0 to 16. [no] Use no stack-unit unit-id stack-group stack-id to remove the current stack group configuration. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 2014
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.
PAGE 2015
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information Prior to disabling the stackable VLAN feature, remove the members. To view the stackable VLANs, use the show vlan command in EXEC Privilege mode.
PAGE 2016
sp-tag-dot1p value Enter the keyword sp-tag-dot1p then the service provider dot1p value. The range is from 0 to 7. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 2017
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale. C-Series and S-Series accept both bytes of the 2-byte S-Tag TPID. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series and S-Series. E-Series original Command Usage Information For specific interoperability limitations regarding the S-Tag TPID, refer to the Dell Networking OS Configuration Guide.
PAGE 2018
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series ExaScale.
PAGE 2019
interface TenGigabitEthernet 1/42 no ip address switchport vlan-stack trunk no shutdown Dell(conf-if-te-1/42)#interface vlan 100 Dell(conf-if-vl-100)#vlan-stack compatible Dell(conf-if-vl-100-stack)#member tengigabitethernet 1/42 Dell(conf-if-vl-100-stack)#show config ! interface Vlan 100 no ip address vlan-stack compatible member TenGigabitEthernet 1/42 shutdown Dell(conf-if-vl-100-stack)#interface vlan 20 Dell(conf-if-vl-20)#tagged Tengigabitethernet 1/42 Dell(conf-if-vl-20)#show config ! interface Vlan 2
PAGE 2020
Dell(conf-if-vlan)#exit Dell(config)# 2020 VLAN Stacking
PAGE 2021
Virtual Routing and Forwarding (VRF) 68 Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist on the same router at the same time. ip vrf Creates a customer VRF. Syntax ip vrf {vrf-name | management} [vrf_id] To delete a customer VRF, use the no ip vrf {vrf-name | management} [vrf_id] command. Parameters vrf-name Enter the name of the VRF that you want to create. management Use this keyword when you want to create the management VRF.
PAGE 2022
description Enables you to specify a descriptive name for a customer VRF. Syntax description string To delete the descriptive name for a customer VRF, use the no description string command. Parameters string Enter a descriptive name for the VRF. Defaults None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 2023
Command Modes INTERFACE-CONFIG Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. Use this command to attach an interface to a configured VRF.
PAGE 2024
ip route-export Enables route leaking between VRFs. Exports or shares IPv4 routes corresponding to one VRF with other non-default VRFs. Syntax Parameters ip route-export tag [route-map-name] route-export Enter the keyword to leak or share routes between VRFs. tag Enter a tag (export route target) to expose routes to other VRFs. This tag acts as an identifier for exported routes. You can use this identifier while importing these routes into another non-default VRF.
PAGE 2025
Related Commands ip route-import – imports routes from another VRF. ip route-import Imports IPv4 routes that are leaked by another VRF using the tag specified by that VRF during export of these routes. Syntax Parameters ip route-import tag [route-map—name] route-import Enter the keyword route-import to import routes into the VRF. tag Enter a tag (ASN number) to specify an import route target for importing routes from another VRF.
PAGE 2026
Related Commands ip route-export – exports routes to another VRF. ipv6 route-export Enables route leaking between VRFs. Exports or shares IPv6 routes corresponding to one VRF with other non-default VRFs. Syntax Parameters Defaults Command Modes ipv6 route-export tag [route-map-name] route-export Enter the keyword route-export to leak or share routes between VRFs. tag Enter a tag (ASN number) as the export route target to expose routes to other VRFs. This tag acts as an identifier for exported routes.
PAGE 2027
Only Active routes are eligible for leaking. For example, if one VRF has two routes corresponding to BGP and OSPF, in which the BGP route is not active, the OSPF route takes precedence over BGP. Even though the Target VRF has specified filtering options to match BGP, the BGP route is not leaked as that route is not active in the Source VRF. Related Commands ipv6 route-import – imports IPv6 routes from another VRF.
PAGE 2028
Usage Information It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. Related Commands ipv6 route-export – exports IPv6 routes to another VRF. match source-protocol Enables you to specify matching criteria while exporting or importing routes.
PAGE 2029
Related Commands ipv6 route-import – imports IPv6 routes from another VRF. redistribute Redistributes leaked or exported routes corresponding to specific protocols. Syntax Parameters redistribute {imported-bgp | import-ospf | import-isis} imported-bgp Enter the keyword imported-bgp to redistribute leaked routes that are learnt using the BGP protocol. imported-ospf Enter the keyword imported-ospf to redistribute leaked routes that are learnt using the OSPF protocol.
PAGE 2030
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. Use this command to associate a management port with a management VRF.
PAGE 2031
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OSCommand Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4(0.0) Introduced on the S–Series.
PAGE 2032
Ma Ma Ma Ma Ma Ma Nu 0, 6/0, 7/0, 8/0, 9/0, 10/0, 11/0, Vl 1 Te 0/14,16-17 Te 0/15 test1 test2 management 1 2 64 FTOS#show ip vrf test1 VRF-Name VRF-ID Interfaces test1 1 Te 0/14,16-17 show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax Parameters Command Modes Command History show run vrf vrf-name vrf vrf-name • EXEC • EXEC Privilege Enter the keyword vrf and then the name of the VRF.. This guide is platform-specific.
PAGE 2033
VLT Proxy Gateway 69 The Virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a L3 end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, refer to Dell Networking OS Command Line Reference Guide. proxy-gateway lldp Enables the proxy-gateway feature using LLDP protocol.
PAGE 2034
proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000. Usage Information When proxy-gateway static configuration is added, the setting is saved in the Layer 2 module.
PAGE 2035
Command Modes Command History VLT DOMAIN PROXY GW STATIC Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. Usage Information You can configure the MAC address, of a VLT peer in remote VLT Domain, to be associated with the static VLT proxy gateway and exclude a VLAN or a range of VLANs from proxy routing..
PAGE 2036
Version Description 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. Usage Information The VLT port channel interface which is connecting to the remote VLT domain must be configured as peer-domain-link. Configure the VLANs that needs to be excluded from VLT Proxy Gateway.
PAGE 2037
vlt-peer-mac transmit Enables the device to transmit, the peer's MAC address along with its own mac-address in the LLDP TLV packets, to the remote VLT Domain. Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000.
PAGE 2038
Usage Information At any point of time the proxy-gateway feature may go operationally down for the following reasons, 1) LLDP globally disabled 2) LLDP disabled per port 3) VLT port-channel is down 4) LLDP neighbor down So, the proxy-gateway feature could be operationally down though properly configured and this will be reported in the “show command”.
PAGE 2039
Virtual Link Trunking (VLT) 70 Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 2040
interval seconds Enter the keyword interval to specify the time interval to send hello messages. The range is from 1 to 5 seconds. The default is 1 second. Defaults 1 second Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.
PAGE 2041
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.2(0.2) Added multicast and ndp parameters. 9.0.
PAGE 2042
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.
PAGE 2043
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810.
PAGE 2044
Parameters value Enter the timeout value in seconds. The range is from 1 to 1200. The default is 150. Command Modes VLT DOMAIN (conf-vlt-domain) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(0.
PAGE 2045
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan parameter. 8.3.8.0 Introduced on the S4810.
PAGE 2046
Version Description 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. peer-routing-timeout Configure the delay after which peer routing is disabled when the peer is unavailable. This command is applicable for both IPV6/IPV4. If not configured, peer-routing will not be disabled at all even though the peer is unavailable. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value in seconds.
PAGE 2047
Parameters value To configure the primary role on a VLT peer, enter a lower value than the priority value of the remote peer. The range is from 1 to 65535. Default 32768 Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.
PAGE 2048
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell Networking OS version number. VLT version numbers are begin with odd numbers such as 3 or 5.
PAGE 2049
Example Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays the counter information.
PAGE 2050
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Usage Information If you do not add a parameter such as arp or mac, the output displays all of the counters.
PAGE 2051
show vlt detail Displays detailed status information about VLT domains currently configured on the switch. Syntax show vlt detail Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 2052
Example Version Description 9.5(0.0) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. Dell#show vlt inconsistency ip mroute Spanned Multicast Routing IIF Inconsistency Multicast Route --------------(22.22.22.200, 225.1.1.2) (*, 225.1.1.
PAGE 2053
System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:bc 32768 Dell_VLTpeer2# show vlt role VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 show vlt statistics Displays statistics on VLT operations.
PAGE 2054
Related Commands Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support in the output for ARP, MAC, and IGMP snooping. 8.3.8.0 Introduced on the S4810. clear vlt statistics — clears the statistics on VLT operations. NOTE: The following example shows the statistics for all of the VLT parameters. If you enter a specific keyword, such as mac, only the statistics for that VLT parameter displays.
PAGE 2055
VLT NDP Statistics -------------------NDP NA VLT Tunnel Pkts sent:16 NDP NA VLT Tunnel Pkts Rcvd:46 NDP NA Non-VLT Tunnel Pkts sent:0 NDP NA Non-VLT Tunnel Pkts Rcvd:0 Ndp-sync Pkts Sent:144 Ndp-sync Pkts Rcvd:105 Ndp Reg Request sent:25 Ndp Reg Request rcvd:24 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History This guide is platform-specific.
PAGE 2056
-------------------------Vlan-ID Local Status ------------------4094 Peer Status ----------- Active Inactive Dell# Example for Qin-Q implementatio n over VLT Dell#show vlt mismatch Domain -----Parameters Local -------------PB for stp Enabled Peer ---Disabled Vlan-type-config ---------------Codes:: P - Primary, C - Community, I - Isolated, N - Normal vlan, M - Vlan-stack Vlan-ID ------- Local ----- 100 Peer ---- N M Port-type-config ---------------Codes:: p - PVLAN Promiscuous port, h - PVLAN Ho
PAGE 2057
Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.7(0.0) Introduced on the S6000-ON. Version 9.5(0.0) Introduced on the Z9500. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.
PAGE 2058
Usage Information Version Description 9.5(0.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, Dell Networking OS automatically creates a VLT-system MAC address used for internal system operations.
PAGE 2059
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. When you create a VLT domain on a switch, Dell Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. The unit IDs are used for internal system operations. Use the unit-id command to explicitly configure the unit ID of a VLT peer. Configure a different unit ID (0 or 1) on each peer switch.
PAGE 2060
Usage Information The VLT domain ID must be the same between the two VLT devices. If the domain ID is not the same, a syslog message is generated and VLT does not launch. Related Commands show vlt — uses the show vlt brief command to display the delay-restore value. vlt-peer-lag port-channel Associate the port channel to the corresponding port channel in the VLT peer for the VLT connection to an attached device.
PAGE 2061
Virtual Router Redundancy Protocol (VRRP) 71 Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on Dell Networking OS. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter a number of seconds. The range is from 1 to 255.
PAGE 2062
Usage Information Version Description 9.5(0.0) Added support for centisecs on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command.
PAGE 2063
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 2064
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. debug vrrp Allows you to enable debugging of VRRP.
PAGE 2065
database Enter the keyword database to enable debugging of configuration changes. interface Enter the keyword interface to enable debugging of interface state changes.. ipv6 Enter the keyword ipv6 to enable debugging for IPv6. packets Enter the keyword packets to enable debugging of VRRP control packets. state Enter the keyword state to enable debugging of VRRP state changes. timer Enter the keyword timer to enable debugging of the VRRP timer.
PAGE 2066
Defaults Not enabled. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 2067
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information To enable VRRP traffic, assign an IP address to the VRRP group using the virtual-address command and enter no disable. Related Commands virtual-address — specifies the IP address of the virtual router. hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router.
PAGE 2068
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information If a switch is a MASTER and you change the hold timer, disable and re-enable VRRP for the new hold timer value to take effect. Related Commands disable — disables a VRRP group. preempt To preempt or become the MASTER router, permit a BACKUP router with a higher priority value.
PAGE 2069
priority Specify a VRRP priority value for the VRRP group. The VRRP protocol uses this value during the MASTER election process. Syntax priority priority To return to the default value, use the no priority command. Parameters priority Enter a number as the priority. Enter 255 only if the router’s virtual address is the same as the interface’s primary IP address (that is, the router is the OWNER). The range is from 1 to 255. The default is 100.
PAGE 2070
show config View the non-default VRRP configuration. Syntax Parameters show config [verbose] verbose (OPTIONAL) Enter the keyword verbose to view all VRRP group configuration information, including defaults. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 2071
vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view active VRRP groups corresponding to that VRF. interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For Port Channel interface types, enter the keywords port-channel then the number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN interface, enter the keyword vlan then the VLAN ID.
PAGE 2072
Item Description Interface Lists the interface type, slot and port on which the VRRP group is configured. Grp Displays the VRRP group ID. Pri Displays the priority value assigned to the interface. If the track command is configured to track that interface and the interface is disabled, the cost is subtracted from the priority value assigned to the interface. Pre States whether preempt is enabled on the interface. State • Y = Preempt is enabled. • N = Preempt is not enabled.
PAGE 2073
Item Description • master (MASTER virtual router) • backup (BACKUP virtual router) the interface’s priority and the IP address of the MASTER. Hold Down:... Adv rcvd:... Example This line displays additional VRRP configuration information: • Hold Down displays the hold down timer interval in seconds. • Preempt displays TRUE if preempt is configured and FALSE if preempt is not configured. • AdvInt displays the Advertise Interval in seconds.
PAGE 2074
TenGigabitEthernet 1/4, VRID: 2, Net: 10.1.2.253 State: Master, Priority: 110, Master: 10.1.2.253 (local) Hold Down: 10 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:02 Virtual IP address: 10.1.2.
PAGE 2075
Usage Information Version Description 7.6.1.0 Introduced on the S-Series (S50 only). 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If the interface is disabled, the cost value is subtracted from the priority value and forces a new MASTER election if the priority value is lower than the priority value in the BACKUP virtual routers. virtual-address Configure up to 12 IP addresses of virtual routers in the VRRP group.
PAGE 2076
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced support for telnetting to the VRRP group IP address assigned using this command. 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when a virtual IP address is configured. When you delete the virtual address, the VRRP group stops sending VRRP packets.
PAGE 2077
Usage Information Related Command Version Description 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. This command applies to a single interface. When used with the vrrp delay reload CLI, the later timer rules the VRRP enabling. For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 2078
Usage Information This command applies to all the VRRP configured interfaces on a system. When used with the vrrp delay minimum CLI, the later timer rules the VRRP enabling. For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP on all interfaces that are up and configured for VRRP.
PAGE 2079
Usage Information The VRRP group only becomes active and sends VRRP packets when a virtual IP address is configured. When you delete the virtual address, the VRRP group stops sending VRRP packets. Related Command virtual-address — assigns up to 12 virtual IP addresses per VRRP group. IPv6 VRRP Commands The following are IPv6 VRRP commands.
PAGE 2080
Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series. Support was added for IPv6 VRRP groups in non-default VRF instances. 8.3.2.0 Introduced on the E-Series TeraScale. debug vrrp ipv6 Allows you to enable debugging of VRRP.
PAGE 2081
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series.
PAGE 2082
Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.3.2.
PAGE 2083
Line Beginning with Description • Example Bad pkts rcvd displays the number of invalid packets received on the interface. Virtual MAC address Displays the virtual MAC address of the VRRP group. Virtual IP address Displays the virtual IP address of the VRRP router to which the interface is connected. Tracking states... Displays information on the tracked interfaces or objects configured for a VRRP group (track command), including: • UP or DOWN state of the tracked interface or object (Up or Dn).
PAGE 2084
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 8.4.2.1 The range of valid VRID values on the E-Series when VRF microcode is loaded in CAM changed from 1 to 15. 8.4.1.
PAGE 2085
Debugging and Diagnostics 72 The basic debugging and diagnostic commands are supported by the Dell Networking OS on the S5000 switch. This chapter contains the following sections: • Offline Diagnostic Commands • Buffer Tuning Commands • Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 2086
Usage Information The Kernel core dump can be large and may take up to 5 to 30 minutes to upload. Dell Networking OS does not overwrite application core dumps so you should delete them as necessary to conserve space on the flash; if the flash is out of memory, the coredump is aborted. On the S-Series, if the FTP server is not reachable, the application coredump is aborted. Dell Networking OS completes the coredump process and wait until the upload is complete before rebooting the system.
PAGE 2087
on 10G links. At this level, stack ports are shut down automatically. level2 Enter the keyword level2 to run Level 2 diagnostics. Level 2 diagnostics are a full set of diagnostic tests with no support for automatic partitioning. Level 2 diagnostics are used primarily for on-board loopback tests and more extensive component diagnostics. Various components on the board are put into Loopback mode and test packets are transmitted through those components.
PAGE 2088
Parameters number Enter the stack-unit id. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 2089
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 2090
Parameters fp Enter the keyword fp to create a buffer profile for the Field Processor. csf Enter the keyword csf to create a buffer profile for the Switch Fabric Processor. profile-name Create a name for the buffer profile, global Apply one of two pre-defined buffer profiles to all of the port-pipes in the system. 1Q Enter the keyword 1Q to choose a pre-defined buffer profile for single queue (for example, non-QoS) applications.
PAGE 2091
show buffer-profile stack-unit Display the buffer profile that is applied to a stack-unit. S5000 Syntax Parameters show buffer-profile stack—unit unit-number stack-unit unitnumber Defaults none Command Modes EXEC Privilege Command History Example (single unit) Version 9.0(1.3) Enter the keyword stack-unit followed by the unit number. The range is 0 to 11. If you do not type a unit number, Dell Networking OS displays buffer-profiles for all units. Introduced on the S5000.
PAGE 2092
counters Enter the keyword counters to clear the counters on the selected stack member. unit number counters Enter the keyword unit along with a port-pipe number, then the keyword counters to clear the counters on the selected port-pipe. cpu data-plane statistics Enter the keywords cpu data-plane statistics to clear the data plane statistics. cpu party-bus statistics Enter the keywords cpu party-bus statistics to clear the management statistics.
PAGE 2093
Parameters stack-unit number Enter the keywords stack-unit then a number to select a particular stack member and then enter one of the following command options to clear a specific collection of data. port-set 0–0 counters Enter the keywords port-set along with a port-pipe number, then the keyword counters to clear the system-flow counters on the selected port-pipe. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 2094
The following is a list of the Dell Networking OS version history for this command. Version Description 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command. hardware watchdog To trigger a reboot and restart the system, set the watchdog timer. Syntax hardware watchdog stack-unit {<0-5> | all} Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 2095
stack-unit id Enter the keyword stack-unit to select a stack ID. port-set 0–0 Enter the keywords port-set with a port-pipe number. . Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.7(0.
PAGE 2096
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. show hardware stack-unit Display the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 2097
drops [unit unit-number [port portnumber | no]] Enter the keyword drops to display internal drops on the selected stack member. Enter the drops keyword to display internal drops on the selected stack member. Option unit 0 followed by port 1-104 (in S6000) is based on internal/ hardware port number” and “option user-port 0-127 is to see the drop using user port numbering convention. fpga register Enter the keyword to display the register value of fpga resgister details in S4810, Z9000 and S6000.
PAGE 2098
Example (DataPlane) Dell#show hardware stack-unit 1 cpu data-plane statistics Input Statistics: 1856 packets, 338262 bytes 141 64-byte pkts, 1248 over 64-byte pkts, 11 over 127-byte pkts 222 over 255-byte pkts, 236 over 511-byte pkts, 0 over 1023byte pkts 919 Multicasts, 430 Broadcasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 325 packets, 27629 bytes, 0 underruns 9 64-byte pkts, 310 over 64-byte pkts, 1 over 127-byte pkts 1 over 255-byte pkts, 2 over 511-byte pkts, 2
PAGE 2099
Packets dropped by FP : 0 (L2+L3) Drops : 0 Port bitmap zero Drops : 0 Rx VLAN Drops : 0 --- Ingress MAC counters--Ingress FCSDrops : 0 Ingress MTUExceeds : 0 --- MMU Drops --HOL DROPS : 0 TxPurge CellErr : 0 Aged Drops : 0 --- Egress MAC counters--Egress FCS Drops : 0 --- Egress FORWARD PROCESSOR Drops --IPv4 L3UC Aged & Drops : 0 TTL Threshold Drops : 0 INVALID VLAN CNTR Drops : 0 L2MC Drops : 0 PKT Drops of ANY Conditions : 0 Hg MacUnderflow : 0 TX Err PKT Counter : 0 25 Dell# Example (PortStats) Exampl
PAGE 2100
0x00680017 0x0060004c 0x0060104c 0x0060204c 0x0060304c 0x0060404c 0x0060504c 0x0060604c 0x0060704c 0x0060804c 0x0060904c 0x0060a04c 0x0060b04c 0x0060c04c 0x0060d04c 0x0060e04c 0x0060f04c 0x0061004c 0x0061104c 0x0061204c 0x0061304c 0x0061404c 0x0061504c 0x0061604c 0x0061704c 0x0061804c 0x0061904c 0x0061a04c 0x0061b04c 0x0061c04c 0x00780000 0x0e700102 0x0e701102 0x0e702102 0x0e703102 0x0e704102 0x0e705102 0x0e706102 0x0e707102 0x0e708102 0x0e709102 0x0e70a102 0x0e70b102 0x0e70c102 0x0e70d102 0x0e70e102 0x0e70
PAGE 2101
0x0b704001 BCAST_STORM_CONTROL.ge4 = 0x00000000 0x0b705001 BCAST_STORM_CONTROL.ge5 = 0x00000000 0x0b706001 BCAST_STORM_CONTROL.ge6 = 0x00000000 0x0b707001 BCAST_STORM_CONTROL.ge7 = 0x00000000 0x0b708001 BCAST_STORM_CONTROL.ge8 = 0x00000000 0x0b709001 BCAST_STORM_CONTROL.ge9 = 0x00000000 0x0b70a001 BCAST_STORM_CONTROL.
PAGE 2102
The linkStatus of Hg Port 27 is FALSE !------------------ output truncated ---------------! Example (Total-Buffer) Dell#show hardware stack-unit 1 buffer total-buffer Example (Buffer-Info) Dell# show hardware stack-unit 1 buffer unit 0 port 1 bufferinfo ----- Buffer Stats for Unit 1 Port 1 ----Maximum Shared Limit for the Port: 30720 Default Packet Buffer allocate for the Port: 120 Dell#show hardware stack-unit 1 buffer total-buffer ----- Buffer Details for Stack-Unit 1 ----Total Buffers allocated per S
PAGE 2103
port-set number [counters] Enter the keywords port-set with a port-pipe number. (OPTIONAL) Enter the keyword counters to display hit counters for the selected ACL or QoS option. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 2104
25 Dell# Example param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=1, mode=0x01, entries=1} ############## FP Entry for redirecting LACP traffic to CPU Port ############ EID 2045: gid=1, slice=15, slice_idx=0x02, prio=0x7fd, flags=0x82, Installed tcam: color_indep=0, higig=0, higig_mask=0, KEY=0x00000000 00000000 00000000 0180c200 00020000 0000
PAGE 2105
show hardware vlan-counters Display the hardware VLAN statistics. Syntax Parameters show hardware vlan-counters vlan-id vlan-id Enter the interface VLAN number. The range is from 1 to 4094. Defaults None Command Modes • EXEC • EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 2106
Debugging and Diagnostics
PAGE 2107
A ICMP Message Types This chapter lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. ICMP Messages and Their Definitions. Symbol Type Code . Query Error Timeout (no reply) ! 0 U 3 C Description 4 3 . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 2108
Symbol & Type Code Description 1 redirect for host . 2 redirect for type-of-service and network . 3 redirect for type-of-service and host . 8 0 echo request . 9 0 router advertisement . 10 0 router solicitation . 11 Error time exceeded: 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 2108 Query parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request .
PAGE 2109
B SNMP Traps This chapter lists the traps sent by the Dell Networking operating software. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Message ID Trap Type Trap Option COLD_START SNMP COLDSTART WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP LINKDOWN SNMP LINKUP SNMP AUTH EGP_NEIGHBOR_LOSS SNMP NONE OSTATE_DOWN SNMP LINKDOWN SNMP LINKUP SNMP NONE SNMP NONE %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent.
PAGE 2110
Message ID Trap Type Trap Option RMON_HC_RISHING_THRESHOLD SNMP NONE SNMP NONE SNMP NONE SNMP NONE SNMP NONE NONE NONE ENVMON NONE ENVMON NONE ENVMON NONE CHM_CARD_PROBLEM ENVMON NONE CHM_ALARM_CUTOFF ENVMON NONE CHM_SFM_UP ENVMON NONE CHM_SFM_DOWN ENVMON NONE CHM_RPM_UP ENVMON NONE ENVMON NONE %RPM0-P:CP %SNMP-4-RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID RMON_HC_FALLING_THRESHOLD %RPM0-P:CP %SNMP-4-RMON_HC_FALLING_THRESHOLD
PAGE 2111
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY %CHMGR-2-RPM_DOWN: RPM 0 down - hard reset %CHMGR-2-RPM_DOWN: RPM 0 down - card removed CHM_RPM_PRIMARY %RAM-5-COLD_FAILOVER: RPM Failover Completed %RAM-5-HOT_FAILOVER: RPM Failover Completed %RAM-5-FAST_FAILOVER: RPM Failover Completed CHM_SFM_ADD %TSM-5-SFM_DISCOVERY: Found SFM 1 CHM_SFM_REMOVE
PAGE 2112
Message ID Trap Type Trap Option CHM_MIN_ALARM_PS_CLR ENVMON SUPPLY ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON FAN ENVMON FAN ENVMON FAN ENVMON FAN %CHMGR-5-MINOR_PS_CLR: Minor alarm cleared: power supply redundant CHM_MIN_ALRM_TEMP %CHMGR-2-MINOR_TEMP: Minor alarm: chassis temperature CHM_MIN_ALRM_TEMP_CLR %CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC) CHM_MAJ_ALRM_TEMP %CHMGR-2-MAJOR_TEMP: Major alar
PAGE 2113
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE PROTO NONE For E1200: %CHMGR-2-FAN_OK: Minor alarm cleared: all fans in fan tray %d are good For E600 and E300: %CHMGR-5-FANOK: Minor alarm cleared: all fans in fan tray are good TME_TASK_SUSPEND %TME-2-TASK SUSPENDED: SUSPENDED - svce:%d - inst: %d - task:%s TME_TASK_TERM %TME-2-ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CHM_CPU
PAGE 2114
Message ID Trap Type Trap Option PROTO NONE PROTO NONE PROTO NONE PROTO NONE %RPM1-P:RP2 %VRRP-3-VRRP_BAD_AUTH: vrid-1 on Gi 11/12 rcvd pkt with authentication failure VRRP_GO_MASTER %VRRP-6-VRRP_MASTER: vrid-%d on %s entering MASTER VRRP_PROTOCOL_ERROR VRRP_PROTOERR: VRRP protocol error on %S BGP4_ESTABLISHED %TRAP-5-PEER_ESTABLISHED: Neighbor %a, state %s BGP4_BACKW_XSITION %TRAP-5-BACKWARD_STATE_TRANS: Neighbor %a, state %s 2114 SNMP Traps