Install Guide
Table Of Contents
- Dell EMC PowerSwitch S5200F-ON Series Installation Guide January 2021
- About this guide
- S5200F-ON Series switch
- Site preparations
- S5200F-ON Series switch installation
- Power supplies
- Fans
- Management ports
- Specifications
- Chassis physical design
- IEEE standards
- Agency compliance
- USA Federal Communications Commission statement
- European Union EMC directive conformance statement
- Japan VCCI compliance for class A equipment
- Korean certification of compliance
- Safety standards and compliance agency certifications
- Electromagnetic compatibility
- Product recycling and disposal
- Dell EMC support
00:14.1 Class 0200: 8086:1f41
00:14.2 Class 0200: 8086:1f41
00:16.0 Class 0c03: 8086:1f2c
6:1f22 lass 0106: 8086:1f32
00:1f.0 Class 0601: 8086:1f38
00:1f.3 Class 0c05: 8086:1f3c
01:00.0 Class 0200: 14e4:b960 (NPU PCI detection)
01:00.1
ONIE:/ #
ONIE service discovery
ONIE attempts to locate the installer through several discovery methods.
To download and run an installer, the ONIE Service Discovery feature follows these steps in order and uses the first successful
method found:
1. Search locally attached storage devices for one of the ONIE default installer filenames—for example, onie self update
from the USB.
2. Discover TFTP-based image from the DHCP server.
3. Query to the IPv6 link-local neighbors using HTTP for an installer.
If none of the ONIE Service Discovery methods are successful, you can disable this using the onie-discovery-stop
command.
You can install an operating system manually from HTTP, FTP, or TFTP using the onie-nos-install <URL> command.
NOTE:
If you have a recovery USB plugged into your switch, you must remove it before using the onie-nos-install
command.
The ONIE Install environment uses DHCP to assign an IP address to the management interface—eth0. If that fails, it uses the
default IP address 192.168.3.10/255.255.255.0.
To display the IP address, use the ifconfig eth0 command, as shown.
ONIE:/ # ifconfig eth0
eth0 Link encap:Ethernet HWaddr 90:B1:1C:F4:9C:76
inet addr:10.11.53.33 Bcast:10.255.255.255 Mask:255.0.0.0
inet6 addr: fe80::92b1:1cff:fef4:9c76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18 errors:0 dropped:0 overruns:0 frame:0
TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:1152 (1.1 KiB) TX bytes:6864 (6.7 KiB)
Interrupt:21 Memory:ff300000-ff320000
To assign an IP address to the management interface, eth0, and verify network connectivity, use the ifconfig eth0 <ip
address> command, as shown.
ONIE:/ # ifconfig eth0 10.11.53.33/16 UP
Verify the network connection with ping.
ONIE:/ # ping 10.11.8.12
PING 10.11.8.12 (10.11.8.12): 56 data bytes
64 bytes from 10.11.8.12: seq=0 ttl=62 time=1.357 ms
64 bytes from 10.11.8.12: seq=1 ttl=62 time=0.577 ms
^C
56
Management ports