Users Guide

2.1.1.2/32 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 0
0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0
1.1.1.0/24 Direct, Vl 1000 0.0.0.0 00:00:00:00:00:00 CP 1000 0
1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0
2.1.1.0/24 Direct, Vl 20 0.0.0.0 00:00:00:00:00:00 CP 20 0
2.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0
100.1.1.0/24 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Te 1/1/1/2 1000 1
100.1.1.0/24 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 1
Dell#
Dell#show ip route
S 10.1.1.0/24 via 1.1.1.2, Vl 10
via 2.1.1.2, Vl 20
S 20.1.1.0/24 via 3.1.1.2, Vl 30
S 100.1.1.0/24 via 10.1.1.0, weight 7
via 20.1.1.0, weight 1
Example (Show
command output
with Weighted
ECMP Enabled)
Dell# show ip fib stack-unit 1
Destination Gateway First-Hop Mac-Addr Port VId EC RC W
------------------------------------------------------------------------------
0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 - -
1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - -
1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 - -
The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp
weighted command.
Related Commands
• clear ip b stack-unit — clear FIB entries on a specied stack-unit.
• ip ecmp weighted— enable weighted ECMP calculations.
show ip ow
Show how a Layer 3 packet is forwarded when it arrives at a particular interface.
Syntax
show ip flow interface interface {source-ip address destination-ip address}
{protocol number [tcp | udp]} {src-port number destination-port number}
Parameters
interface interface Enter the keyword interface then one of the following interface keywords.
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then
the stack/slot/port/subport information.
• For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the
stack/slot/port/subport information.
•
For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/
slot/port[/subport] information.
• For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/
slot/port/subport information.
• For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the
stack/slot/port information.
source-ip address Enter the keywords source-ip then the IP source address in IP address format.
destination-ip
address
Enter the keywords destination-ip then the IP destination address in IP address
format.
protocol number
[tcp | udp]
Enter the keyword protocol then one of the protocol type keywords: tcp, udp, or
protocol number The protocol number range is from 0 to 255. .
src-port number Enter the keywords src-port then the source port number.
IPv4 Routing 793