Users Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S6100-ON

Dell Command Line Reference Guide for the

S6100–ON System

9.10(0.2)

Summary of content (1677 pages)

PAGE 1
Dell Command Line Reference Guide for the S6100–ON System 9.10(0.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
PAGE 3
Contents 1 About this Guide...........................................................................................................................................39 Objectives......................................................................................................................................................................... 39 Audience........................................................................................................................................................
PAGE 4
banner exec...................................................................................................................................................................... 84 banner login...................................................................................................................................................................... 85 banner motd..........................................................................................................................................
PAGE 5
show system................................................................................................................................................................... 139 show tech-support..........................................................................................................................................................141 ssh-peer-stack-unit...........................................................................................................................................
PAGE 6
ip control-plane egress-filter................................................................................................................................... 185 show ip accounting access-list...............................................................................................................................185 Standard IP ACL Commands.........................................................................................................................................187 deny................
PAGE 7
clear ip prefix-list......................................................................................................................................................245 deny........................................................................................................................................................................... 245 ip prefix-list................................................................................................................................................
PAGE 8
permit icmp (for Extended IP ACLs)........................................................................................................................... 292 permit udp (for Extended IP ACLs).............................................................................................................................293 permit (for Extended IP ACLs)....................................................................................................................................
PAGE 9
bgp regex-eval-optz-disable...................................................................................................................................339 bgp router-id.............................................................................................................................................................340 clear ip bgp................................................................................................................................................................
PAGE 10
permit bandwidth.................................................................................................................................................... 385 redistribute................................................................................................................................................................386 redistribute ospf......................................................................................................................................................
PAGE 11
show ip protocol-queue-mapping................................................................................................................................ 442 show ipv6 protocol-queue-mapping............................................................................................................................443 show mac protocol-queue-mapping............................................................................................................................444 11 Data Center Bridging (DCB).
PAGE 12
diag stack-unit..........................................................................................................................................................479 offline stack-unit...................................................................................................................................................... 480 online stack-unit.....................................................................................................................................................
PAGE 13
ip dhcp relay..............................................................................................................................................................527 ip dhcp snooping......................................................................................................................................................528 ipv6 dhcp snooping.................................................................................................................................................
PAGE 14
debug fip snooping rx....................................................................................................................................................564 feature fip-snooping......................................................................................................................................................565 fip-snooping enable..................................................................................................................................................
PAGE 15
ip igmp access-group.............................................................................................................................................. 607 ip igmp immediate-leave......................................................................................................................................... 608 ip igmp last-member-query-interval...................................................................................................................... 609 ip igmp query-interval.
PAGE 16
rate-interval.............................................................................................................................................................. 662 show config.............................................................................................................................................................. 663 show config (for speed).........................................................................................................................................
PAGE 17
ip address........................................................................................................................................................................ 724 ip directed-broadcast.................................................................................................................................................... 725 ip domain-list.............................................................................................................................................
PAGE 18
ipv6 route........................................................................................................................................................................ 783 show ipv6 route..............................................................................................................................................................785 24 IPv6 Access Control Lists (IPv6 ACLs)....................................................................................................
PAGE 19
isis csnp-interval.............................................................................................................................................................828 isis hello-interval.............................................................................................................................................................828 isis hello-multiplier....................................................................................................................................
PAGE 20
show iscsi session detailed............................................................................................................................................873 show run iscsi................................................................................................................................................................. 874 27 Link Aggregation Control Protocol (LACP)...............................................................................................
PAGE 21
29 Link Layer Discovery Protocol (LLDP)......................................................................................................919 LLPD Commands........................................................................................................................................................... 919 advertise dot1-tlv......................................................................................................................................................919 advertise dot3-tlv....
PAGE 22
ip msdp shutdown......................................................................................................................................................... 959 ip multicast-msdp.......................................................................................................................................................... 959 show ip msdp......................................................................................................................................................
PAGE 23
reachable–time........................................................................................................................................................ 999 retrans-time............................................................................................................................................................ 1000 router–lifetime........................................................................................................................................................
PAGE 24
fast-convergence................................................................................................................................................... 1044 flood-2328...............................................................................................................................................................1045 graceful-restart grace-period...............................................................................................................................
PAGE 25
show ip ospf topology............................................................................................................................................ 1104 summary-address................................................................................................................................................... 1105 timers spf.................................................................................................................................................................
PAGE 26
38 PIM-Sparse Mode (PIM-SM)................................................................................................................. 1156 IPv4 PIM-Sparse Mode Commands...........................................................................................................................1156 clear ip pim rp-mapping..........................................................................................................................................1156 clear ip pim tib...........................
PAGE 27
extend system-id..........................................................................................................................................................1200 protocol spanning-tree pvst.........................................................................................................................................1201 show spanning-tree pvst.............................................................................................................................................
PAGE 28
show qos policy-map..............................................................................................................................................1247 show qos policy-map-input................................................................................................................................... 1249 show qos policy-map-output................................................................................................................................
PAGE 29
redistribute ospf........................................................................................................................................................... 1295 router rip........................................................................................................................................................................1296 show config............................................................................................................................................
PAGE 30
aaa authorization config-commands................................................................................................................... 1340 aaa authorization exec............................................................................................................................................1341 privilege level (CONFIGURATION mode).............................................................................................................1341 privilege level (LINE mode)..............
PAGE 31
dot1x mac-auth-bypass......................................................................................................................................... 1383 dot1x max-eap-req................................................................................................................................................. 1384 dot1x port-control...................................................................................................................................................
PAGE 32
role............................................................................................................................................................................1423 show role................................................................................................................................................................. 1424 show userroles.............................................................................................................................................
PAGE 33
Syslog Commands.........................................................................................................................................................1471 clear logging.............................................................................................................................................................1471 clear logging auditlog.............................................................................................................................................
PAGE 34
52 Spanning Tree Protocol (STP)................................................................................................................ 1515 bridge-priority................................................................................................................................................................1515 bpdu-destination-mac-address...................................................................................................................................
PAGE 35
show running-config.................................................................................................................................................... 1548 show support-assist status.........................................................................................................................................1548 54 System Time and Date...........................................................................................................................
PAGE 36
upstream....................................................................................................................................................................... 1586 57 VLAN Stacking....................................................................................................................................... 1589 dei enable....................................................................................................................................................................
PAGE 37
multicast peer-routing timeout...................................................................................................................................1625 peer-link port-channel................................................................................................................................................. 1626 peer-routing.................................................................................................................................................................
PAGE 38
preempt....................................................................................................................................................................1661 priority...................................................................................................................................................................... 1661 show config.................................................................................................................................................
PAGE 39
1 About this Guide This guide provides information about the Dell Networking operating system (OS) command line interface (CLI). This book also includes information about the protocols and features supported in Dell Networking OS.
PAGE 40
x|y Keywords and parameters separated by a bar require you to choose one option. x||y Keywords and parameters separated by a double bar allow you to choose any or all of the options. Information Icons This guide uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data.
PAGE 41
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols.
PAGE 42
% Warning: The following users are currently configuring the system: User "" on line User "admin" on User "admin" on User "Irene" on Dell#conf console0 line vty0 ( 123.12.1.123 ) line vty1 ( 123.12.1.123 ) line vty3 ( 123.12.1.321 ) When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2.
PAGE 43
tcp telnet tftp unicast-host-route unknown-unicast vlan-flooding vrf global tcp settings Specify telnet options TFTP configuration commands Configuration for ip unicast address-family Enable IPv4 unknown-unicast packets to CPU Vlan flooding Configure VRF instance When entering commands, you can take advantage of the following timesaving features: • Commands are not case-sensitive. • Enter partial (truncated) command keywords.
PAGE 44
The CLI prompt changes as you move up and down the levels of the command structure. Starting with CONFIGURATION mode, the command prompt adds modifiers to further identify the mode. For more information about command modes, see Command Modes. Using the Keyword no Command To disable, delete or return to default values, use the no form of the commands. For most commands, if you type the keyword no in front of the command, you disable that command or delete it from the running configuration.
PAGE 45
Filtering the Command Output Multiple Times You can filter a single command output multiple times. To filter a command output multiple times, place the save option as the last filter. For example: command | grep regular-expression | except regular-expression | grep other-regularexpression | find regular-expression | no-more | save.
PAGE 46
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S5000, and S6000.
PAGE 47
Command Modes To navigate and launch various CLI modes, use specific commands. Navigation to these modes is described in the following sections. BGP ADDRESS-FAMILY Mode To enable or configure IPv4 for BGP, use BGP ADDRESS-FAMILY mode. For more information, see Border Gateway Protocol IPv4 (BGPv4). To enter BGP ADDRESS-FAMILY mode: 1 Verify that you are logged in to ROUTER BGP mode. 2 Enter the address-family command. 3 Enter the protocol type: • For IPv4, enter the ipv4 multicast command.
PAGE 48
DHCP Mode To enable and configure Dynamic Host Configuration Protocol (DHCP), use DHCP mode. For more information, see Dynamic Host Configuration Protocol (DHCP). To enter DHCP mode: 1 Verify that you are logged in to CONFIGURATION mode. 2 Enter the ip dhcp server command. The prompt changes to include config-dhcp. You can return to CONFIGURATION mode by using the exit command. DHCP POOL Mode To create an address pool, use DHCP POOL mode.
PAGE 49
When you are in EXEC mode, the > prompt is displayed following the host name prompt, which is “Dell” by default. You can change the host name prompt using the hostname command. NOTE: Each mode prompt is preceded by the host name. EXEC Privilege Mode The enable command accesses EXEC Privilege mode. If an administrator has configured an “Enable” password, you are prompted to enter it.
PAGE 50
Prompt Interface Type Dell(conf-if)# INTERFACE mode Dell(conf-ifte-1/1/1/1)# Ten-Gigabit Ethernet interface then stack/slot/port/subport information Dell(conf-iftf-1/1/1/1)# Twenty-five Gigabit Ethernet interface then stack/slot/port/subport information Dell(conf-iffo-1/1/1/1)# Forty-Gigabit Ethernet interface then stack/slot/port/subport information or stack/slot/port information, depending on the module used Dell(conf-iffi-1/1/1/1)# Fifty-Gigabit Ethernet interface then stack/slot/port/subport
PAGE 51
1 Verify that you are logged in to ROUTER ISIS mode. 2 Enter the address-family ipv6 unicast command. The prompt changes to include conf-router_isis-af_ipv6. LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more information, see Link Layer Discovery Protocol (LLDP). To enter LLDP mode: 1 To enable LLDP globally, verify that you are logged in to CONFIGURATION mode. To enable LLDP on an interface, verify that you are logged in to INTERFACE mode.
PAGE 52
To enter MONITOR SESSION mode: 1 Verify that you are logged in to CONFIGURATION mode. 2 Enter the monitor session command, and then the session ID. The prompt changes to include conf-mon-sess-sessionID. MULTIPLE SPANNING TREE (MSTP) Mode To enable and configure MSTP, use MULTIPLE SPANNING TREE mode. For more information, see Multiple Spanning Tree Protocol (MSTP). To enter MULTIPLE SPANNING TREE mode: 1 Verify that you are logged in to CONFIGURATION mode.
PAGE 53
PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode. To enter PREFIX-LIST mode: 1 Verify that you are logged in to CONFIGURATION mode. 2 Enter the ip prefix-list command and the name for the prefix list. The prompt changes to include conf-nprefixl. You can return to CONFIGURATION mode by using the exit command. PROTOCOL GVRP Mode To enable and configure GARP VLAN Registration Protocol (GVRP), use PROTOCOL GVRP mode. For more information, see GARP VLAN Registration (GVRP).
PAGE 54
1 Verify that you are logged in to CONFIGURATION mode. 2 Use the router bgp command, and then enter the AS number. The prompt changes to include conf-router_bgp. You can return to CONFIGURATION mode by using the exit command. ROUTER ISIS Mode To enable and configure Intermediate System to Intermediate System (ISIS), use ROUTER ISIS mode. For more information, see Intermediate System to Intermediate System (IS-IS). To enter ROUTER ISIS mode: 1 Verify that you are logged in to CONFIGURATION mode.
PAGE 55
SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode. For more information, see Spanning Tree Protocol (STP). To enter SPANNING TREE mode: 1 Verify that you are logged in to CONFIGURATION mode. 2 Enter the protocol spanning-tree stp-id command. The prompt changes to include conf-stp. You can return to CONFIGURATION mode by using the exit command. SupportAssist Mode To enable and configure the SupportAssist, use SupportAssist mode.
PAGE 56
2 56 Enter the vrrp-group command, and then enter the VRRP group ID. The prompt changes to include conf-if-interfacetype-slot/port-vrid-vrrp-group-id.
PAGE 57
3 File Management This section contains command line interface (CLI) commands needed to manage the configuration files, as well as other file management commands.
PAGE 58
all Enter the keyword all for all the stack units. stack-unit-number Enter the stack-unit number. The range is from 1 to 6. default Enter the keyword default to specify the default Dell Networking OS image. primary Enter the keyword primary to specify the primary Dell Networking OS image. secondary Enter the keyword secondary to specify the secondary Dell Networking OS image. ftp: Enter the keyword FTP: to retrieve the image from an FTP server. ftp:// userid:password@hostip/filepath.
PAGE 59
cd Change to a different working directory. Syntax Parameters cd [flash: | usbflash:] flash: Use the keyword flash: to change the current directory to internal flash and its sub directories. usbflash: Use the keyword usbflash: to change the current directory to the inserted USB.
PAGE 60
flash: Enter the keyword flash: to copy from the local file system ([flash://]filepath). ftp: Enter the keyword ftp: to copy from the remote file system, IPv4, or IPv6, (ftp:// userid:password@hostip/filepath) . http: Enter the keyword http: to copy from the remote file system, IPv4, or IPv6, (http:// hostip/filepath) . nfsmount: Enter the keyword nfsmount: to copy from the nfs mount file system (nfsmount:// /filepath).
PAGE 61
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell Networking OS supports a maximum of 100 files at the root directory level on both the internal and external flash. When copying a file to a remote location (for example, using Secure Copy [SCP]), enter only the keywords and Dell Networking OS prompts you for the rest of the information.
PAGE 62
User name to login remote host: admin Password to login remote host: Destination file name [test.cfg]: test1.cfg Dell# Example Dell# copy compressed-config compressed-cfg ! 6655 bytes successfully copied Dell# Dell#copy compressed-config ftp: Address or name of remote host []: 10.11.8.12 Destination file name [startup-config]: User name to login remote host: spbalaji Password to login remote host: ! 6655 bytes successfully copied Dell# Example Dell# copy http://admin:admin123@10.16.206.
PAGE 63
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. dir Display the files in a file system. The default is the current directory.
PAGE 64
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 65
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series You must include the colon (:) when entering this command. After reformatting is complete, three empty directories are automatically created on flash: CRASH_LOG_DIR, TRACE_LOG_DIR and NVTRACE_LOG_DIR.
PAGE 66
Usage Information Version Description 9.1(0.0) Introduced on S4810 and Z9000. 8.3.19.0 Introduced on S4820T. Include the colon (:) when entering this command. This command checks the specified flash memory for errors. If errors are found, the command recommends that you format the flash. CAUTION: If you elect to format the flash, all files – including the startup configuration file – are lost.
PAGE 67
mount-point Enter the folder name in the local file system. username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 68
upgrade system Upgrade the Dell Networking OS image. To upgrade the bootflash or bootselector image, use the upgrade boot command. Syntax upgrade system {flash: | ftp: | nfsmount: | scp: | stack-unit {stack-unit-id | all} | tftp: | usbflash:} file-url {A: |B:} Parameters system Enter the keyword system to upgrade the operating system (OS) image.
PAGE 69
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility this command accepts IPv6 host addresses with or without the square brackets.
PAGE 70
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.1.0 Introduced on C-Series E-Series Original command show boot system Displays information about boot images currently configured on the system.
PAGE 71
Example Dell#show boot system stack-unit 1 Current system image information in the system: =============================================== Type Boot Type A B ---------------------------------------------------stack-unit 1 FLASH BOOT 9.10(0.0) 9.10(0.0) [boot] Dell# show bootvar Display the variable settings for the boot parameters. Syntax show bootvar Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 72
Reload Mode = Dell# normal-reload show file-systems Display information about the file systems on the system. Syntax show file-systems Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 73
Field Description Flags Displays the access available to the storage location. The following letters indicate the level of access: Prefixes Related Commands • • r = read access • w = write access Displays the name of the storage location. format flash – erases all the existing files and reformats the file system in the internal flash memory. show os-version Display the release and software image version information of the image file specified.
PAGE 74
Example Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell#show os-version RELEASE IMAGE INFORMATION : ----------------------------------------------------------Platform Version Size ReleaseTime S-Series:S6100-ON 9.10(0.0) 54246311 Sep 12 2015 04:21:53 TARGET IMAGE INFORMATION : ------------------------------------------------Type Version Target checksum runtime 9.10(0.
PAGE 75
as-path for the current AS-path configuration bfd for the current BFD configuration bgp for the current BGP configuration boot for the current boot configuration cam-profile for the current CAM profile in the configuration class-map for the current class-map configuration communitylist for the current community-list configuration ecmp-group for the current ECMP group configuration eis for the current EIS configuration ethernet for the current Ethernet CFM configuration fefd for the curr
PAGE 76
File Management mld for the current MLD configuration monitor for the current Monitor configuration mroute for the current Mroutes configuration msdp for the current MSDP configuration ntp for the current NTP configuration ospf for the current OSPF configuration pim for the current PIM configuration policy-mapinput for the current input policy map configuration policy-mapoutput for the current output policy map configuration po-failovergroup for the current port-channel failover-grou
PAGE 77
users for the current users configuration vlt for the current VLT configuration wred-profile for the current wred-profile configuration configured (OPTIONAL) Enter the keyword configuration to display line card interfaces with non-default configurations only. status (OPTIONAL) Enter the keyword status to display the checksum for the running configuration and the start-up configuration. compressed (Optional) Enter the keyword compressed to display the compressed group configuration.
PAGE 78
boot system stack-unit 1 default system: A: boot system gateway 10.16.133.
PAGE 79
Example Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on S-Series 7.5.1.
PAGE 80
Command Fields Example (S6100– ON) Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series 7.5.1.
PAGE 81
System Type: S6100-ON Control Processor: Intel Rangeley with 3 Gbytes (3177226240 bytes) of memory, core(s) 4. 8G bytes of boot flash memory. 1 4 Modules, 16x40G/8x100G ports TE/TF/FO/FI/HU G (S6100-ON) 2 Ten GigabitEthernet/IEEE 802.3 interface(s) 64 Forty GigabitEthernet/IEEE 802.3 interface(s) upgrade boot Upgrade the bootflash image or bootselector image.
PAGE 82
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 9.0(0.0) Added support for IPv6 for the file-url parameter. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series.
PAGE 83
Usage Information Example You can enter this command in the following ways: • verify md5 flash://img-file • verify md5 flash://img-file • verify sha256 flash://img-file • verify sha256 flash://img-file Without Entering the Hash Value for Verification using SHA256 Dell# verify sha256 flash://FTOS-SE-9.5.0.0.bin SHA256 hash for FTOS-SE-9.5.0.0.
PAGE 84
4 Control and Monitoring This section contains command information to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP). banner exec Configure a message that is displayed when your enter EXEC mode. Syntax banner exec c line c To delete a banner, use the no banner exec command. Parameters c Enter the keywords banner exec, then enter a character delineator, represented here by the letter c. Press ENTER.
PAGE 85
Version Description E-Series Original Command Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first. If no message of the day banner is configured, the login banner and prompt appear. After the user has logged in, the banner EXEC (if configured) displays.
PAGE 86
Version Description 9.10(0.0) Introduced the acknowledgement keyword. Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced the keyword keyboard-interactive. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 87
banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator. The delineator is a percent character (%). Defaults No banner is configured.
PAGE 88
cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 89
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.2(0.2) Added support for the fcoe parameter on the S4810 and S4820T. 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.
PAGE 90
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 91
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 92
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. do Allows the execution of most EXEC-level commands from all CONFIGURATION levels without returning to the EXEC level. Syntax do command Parameters Defaults Enter an EXEC-level command.
PAGE 93
Usage Information Example Version Description 6.1.1.0 Introduced on the E-Series. The following commands are not supported by the do command: • enable • disable • exit • config Dell(conf-if-te-1/1/1/1)# do clear counters Clear counters on all interfaces [confirm] Dell(conf-if-te-1/1/1/1)# Dell(conf-if-te-1/1/1/1)# do clear logging Clear logging buffer [confirm] Dell(conf-if-te-1/1/1/1)# Dell(conf-if-te-1/1/1/1)# do reload System configuration has been modified.
PAGE 94
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Users entering EXEC Privilege mode or any other configured privilege level can access configuration commands. To protect against unauthorized access, use the enable password command to configure a password for the enable command at a specific privilege level.
PAGE 95
Usage Information Version Description 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. To enable polling and to configure the polling frequency, use this command. end Return to EXEC Privilege mode from other command modes (for example, CONFIGURATION or ROUTER OSPF modes).
PAGE 96
Related Commands Version Description 7.5.1.0 Introduced on the C-Series and E-Series. E-Series Original command. • exit — returns to the lower command mode. exec-timeout Set a time interval that the system waits for input on a line before disconnecting the session. Syntax exec-timeout minutes [seconds] To return to default settings, use the no exec-timeout command. Parameters minutes Enter the number of minutes of inactivity on the system before disconnecting the current session.
PAGE 97
Example Dell con0 is now available Press RETURN to get started. Dell> exit Return to the lower command mode. Syntax Command Modes Command History exit • EXEC Privilege • CONFIGURATION • LINE, INTERFACE • TRACE-LIST • PROTOCOL GVRP • SPANNING TREE • MULTIPLE SPANNING TREE • MAC ACCESS LIST • ACCESS-LIST • AS-PATH ACL • COMMUNITY-LIST • PREFIX-LIST • ROUTER OSPF • ROUTER RIP • ROUTER ISIS • ROUTER BGP This guide is platform-specific.
PAGE 98
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. E-Series Original command. • end — returns to EXEC Privilege mode. ftp-server enable Enable FTP server functions on the system. Syntax ftp-server [vrf vrf-name] enable Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to enable the FTP server to listen to that VRF instance. NOTE: Use this attribute to specify the VRF that is used by the FTP server to accept client connections.
PAGE 99
Name (10.31.1.111:dch): dch 331 Password required Password: 230 User logged in ftp> pwd 257 Current directory is "flash:" ftp> dir 200 Port set okay 150 Opening ASCII mode data connection size date time name -------- ------ ------ -------512 Jul-20-2004 18:15:00 tgtimg 512 Jul-20-2004 18:15:00 diagnostic 512 Jul-20-2004 18:15:00 other 512 Jul-20-2004 18:15:00 tgt 226 Transfer complete 329 bytes received in 0.018 seconds (17.
PAGE 100
Usage Information Related Commands Version Description E-Series Original command. After you enable FTP server functions with the ftp-server enable command, Dell Networking recommends specifying a top-level directory path. Without a top-level directory path specified, the Dell Networking OS directs users to the flash directory when logging in to the FTP server. • ftp-server enable — enables FTP server functions on the E-Series.
PAGE 101
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. hostname Set the host name of the system. Syntax Parameters hostname name name Enter a text string, up to 32 characters long. Defaults Dell Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 102
ip ftp password Specify a password for outgoing FTP connections. Syntax ip ftp password [encryption-type] password To remove a password and return to the default setting, use the no ip ftp password [password] command. Parameters encryption-type password (OPTIONAL) Enter one of the following numbers: • 0 (zero) for an unecrypted (clear text) password • 7 (seven) for a hidden text password Enter a string up to 40 characters as the password. Defaults Not configured.
PAGE 103
ip ftp source-interface Specify an interface’s IP address as the source IP address for FTP connections. Syntax ip ftp source-interface interface To delete an interface, use the no ip ftp source-interface interface command. Parameters interface Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 104
Version Description 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command.
PAGE 105
To return to anonymous FTP connections, use the no ip ftp username [username] command. Parameters username Enter a text string as the user name up to 40 characters long. Defaults No user name is configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 106
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.
PAGE 107
Related Commands Version Description 6.1.1.0 Introduced on the E-Series. • ip ssh server — enables the secure shell (SSH) server on the system. ip telnet server vrf Configures the TELNET server on either a specific VRF or a management VRF. Syntax ip telnet server vrf {vrf-name | any | management} To undo the TELNET server configuration, use the no ip telnet server [vrf vrf-name] command. Parameters vrf-name Enter the vrf-name to specify the VRF that is used by the TELNET server.
PAGE 108
ip telnet source-interface Set an interface’s IP address as the source address in outgoing packets for Telnet sessions. Syntax ip telnet source-interface interface To return to the default setting, use the no ip telnet source-interface [interface] command. Parameters interface Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 109
Related Commands Version Description 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command telnet — telnet to another device. ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name] command.
PAGE 110
line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. Syntax line {console 0 | vty number [end-number]} Parameters console 0 Enter the keyword console 0 to configure the console port. The console option is <0-0>. vty number Enter the keyword vty then a number from 0 to 9 to configure a virtual terminal line for remote sessions. The system supports 10 remote sessions.
PAGE 111
login concurrent-session Configures the limit of concurrent sessions for all users on console and virtual terminal lines. Syntax login concurrent-session {limit number-of-sessions | clear—line enable} no login concurrent-session {limit number-of-sessions | clear—line enable} Parameters limit number-ofsessions Sets the number of concurrent sessions that any user can have on console and virtual terminal lines. The range is from 1 to 12 (10 VTY lines, one console, and one AUX line).
PAGE 112
When you try to log in, the following message appears with all your existing concurrent sessions, providing an option to close any one of the existing sessions: $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'. Login: admin Password: Current sessions for user admin: Line Location 2 vty 0 10.14.1.97 3 vty 1 10.14.1.
PAGE 113
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. Only the system and security administrators can configure login activity tracking and view the login activity details of other users.
PAGE 114
• show login statistics — displays login statistics of users who have used the console or virtual terminal lines to log in to the system. motd-banner Enable a message of the day (MOTD) banner to appear when you log in to the system. Syntax motd-banner To disable the MOTD banner, use the no motd-banner command. Defaults Enabled on all lines. Command Modes LINE Command History This guide is platform-specific.
PAGE 115
ip-address (OPTIONAL) Enter the IPv4 address of the device to which you are testing connectivity. The address must be in the dotted decimal format. ipv6-address (OPTIONAL) Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros. count Enter the number of echo packets to be sent. The default is 5.
PAGE 116
Defaults sweep-max-size Enter the maximum size of datagram in sweep range. The range is from 53 to 15359 bytes. sweep-interval Enter the incremental value for sweep size. The range is from 1 to 15308 seconds. interface (IPv4 only) Enter the outgoing interface for multicast packets. Enter the IP address in A.B.C.D format. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 117
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards. 8.4.1.0 IPv6 pinging available on management interface. 8.3.1.0 Introduced extended ping options. 8.2.1.0 Introduced on the E-Series (IPv6). 8.1.1.0 Introduced on the E-Series (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for IPv6 address on the E-Series.
PAGE 118
reload Reboot the system. Syntax reload [conditional nvram-cfg-change | no-confirm [discard-running] | dell-diag | onie [install | uninstall | rescue]] Parameters conditional nvramcfg-change (OPTIONAL) Reload into the Dell Networking Operating System (OS) if the condition is true. A configuration change to the NVRAM requires a switch reload. To reload the switch, select nvram-cfg-change. no-confirm [discard-running] Reload the chassis without prompting for further confirmation.
PAGE 119
Usage Information Version Description E-Series Original command. If you use only the reload command, the system boots into the Dell Networking OS. If there is a change in the running configuration, the system prompts you to save the new configuration when you reload the system using the reload command. You can also save your running configuration manually using the copy running-config command.
PAGE 120
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.
PAGE 121
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000.
PAGE 122
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 123
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000.
PAGE 124
show debugging View a list of all enabled debugging processes. Syntax show debugging Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON.
PAGE 125
Command Modes Command History fan Enter the keyword fan to view information on the fans. The output of this command is chassis-dependent. pem Enter the keyword pem to view only information on power entry modules. stack-unit unit-id Enter the keywords stack-unit then the unit-id to display information on a specific stack member. thermal-sensor Enter the keywords thermal-sensor to view information on thermal sensors.
PAGE 126
-----------------------------------* 1 online 32C ok * Management Unit -- Optional Modules Environment Status (deg C) -Unit Module Temperature ---------------------------------------------------1 1 36 1 2 38 1 3 36 1 4 37 -- Thermal Sensor Readings (deg C) -Unit CpuOnBoard Bcm56960_F SysInt Bcm56960_R SwitchOn FP-GE FP-SFP+ Bcm_Int Cpu_Int --------------------------------------------------------------------------------------1 32 36 32 38 34 34 31 53 30 Dell# Dell#show environment fan -- Fan Status -Unit Bay
PAGE 127
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.2) Removed the Dell Qualified column from the show inventory media output. 9.11(0.0) Added support to display 10GBASE-T information on the S4048, S4048T, S6000, S6000ON, S6100, Z9500, S6010, and Z9100. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 128
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1/2 1/3 1/4 1/5 1/6 1/7 1/8 1/9 1/10 1/11 1/12 1/13 1/14 1/15 1/16 2/1 2/2 2/3 2/4 2/5 2/6 2/7 2/8 2/9 2/10 2/11 2/12 2/13 2/14 2/15 2/16 3/1 3/2 3/3 3/4 3/5 3/6 3/7 3/8 3/9 3/10 3/11 3/12 3/13 3/14 3/15 3/16 4/1 4/2 4/3 4/4 4/5 4/6 4/7 4/8 4/9 4/10 4/11 4/12 4/13 4/14 4/15 4/16 5/1 5/2 QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP QSFP Media not pres
PAGE 129
time-period days (Optional)Displays the number of failed login attempts by the current user in the specified period. successfulattempts (Optional)Displays the number of successful login attempts by the current user in the last 30 days or the custom defined time period unsuccessfulattempts (Optional)Displays the number of failed login attempts by the current user in the last 30 days or the custom defined time period.
PAGE 130
User: admin Last login time: 12:52:01 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.143 ) Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 30 day(s): 0 Successful login attempt(s) in last 30 day(s): 1 -----------------------------------------------------------------The following is sample output of the show login statistics all command.
PAGE 131
The following is sample output of the show login statistics unsuccessful-attempts timeperiod days command. Dell# show login statistics unsuccessful-attempts time-period 15 There were 0 unsuccessful login attempt(s) for user admin in last 15 day(s). The following is sample output of the show login statistics unsuccessful-attempts user login-id command. Dell# show login statistics unsuccessful-attempts user admin There were 3 unsuccessful login attempt(s) for user admin in last 12 day(s).
PAGE 132
Version Description 7.6.1.0 Introduced this version of the command for the S-Series. Usage Information The output for show memory displays the memory usage of LP part (sysdlp) of the system. The sysdlp is an aggregate task that handles all the tasks running on the S-Series’ CPU.
PAGE 133
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the keywords management-unit [details]. 7.6.1.0 Introduced on the S-Series.
PAGE 134
details | Detail CPU utilization Pipe through a command Dell# show processes cpu management-unit CPUID 5sec 1min 5min -------------------------------------------------CORE 0 9.54 9.92 12.82 CORE 2 10.74 11.56 14.31 Overall 10.14 10.74 13.
PAGE 135
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 136
Example Dell#show processes ipc flow-control cp Q Statistics on CP Processor TxProcess RxProcess Cur High Len Mark ACL0 RTM0 0 0 ACL0 DIFFSERV0 0 0 ACL0 SNMP0 0 0 LACP0 IFMGR0 0 0 DHCP0 ACL0 0 0 DHCP0 IPMGR0 0 0 DHCP0 IFMGR0 0 0 Time Out 0 0 0 0 0 0 0 Retr ies 0 0 0 0 0 0 0 Msg Sent 0 0 0 0 0 0 0 Ack Rcvd 0 0 0 0 0 0 0 Aval Retra 10 10 10 25 25 25 25 Max Retra 10 10 10 25 25 25 25 show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system.
PAGE 137
Usage Information show processes memory output Description Total: Total system memory available MaxUsed: Total maximum memory used ever (history indicated with time stamp) CurrentUsed: Total memory currently in use CurrentFree: Total system memory available SharedUsed: Total used shared memory SharedFree: Total free shared memory PID Process ID Process Process Name ResSize Actual resident size of the process in memory Size Process test, stack, and data size Allocs Total dynamic memor
PAGE 138
323 frrp 5206016 241664 369238 0 369238 322 xstp 7430144 2928640 38328 0 38328 321 pim 5267456 823296 62168 0 62168 314 igmp 4960256 380928 18588 16564 18588 313 mrtm 6742016 1130496 72758 0 72758 308 l2mgr 5607424 552960 735214 380972 619266 301 l2pm 5001216 167936 1429522 1176044 286606 298 arpm 4628480 217088 71092 33128 71092 294 ospf 5468160 503808 724204 662560 78208 288 dsm 6778880 1159168 39490 16564 39490 287 rtm 5713920 602112 442280 198768 376024 284 rip 4562944 258048 528 0 528 281 lacp 4673536
PAGE 139
Defaults Command Modes Command History Example None. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T.
PAGE 140
stack-unit unit-id Command Modes Command History • EXEC • EXEC Privilege (OPTIONAL) Enter the keywords stack-unit then the stack member ID for information on that stack member. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 141
Boot Selector Memory Size Temperature Voltage Serial Number Part Number Vendor Id Date Code Country Code Piece Part ID PPID Revision Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : : : : : : : : : : : : 3.25.0.
PAGE 142
flash: Save to local flash drive (flash://filename. A maximum of 20 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 143
Example (S-Series) • show log summary • show command-history (last 20 commands) • show log Dell# show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command Dell#show tech-support stack-unit 1 ? | Pipe through a command Dell# show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence of a pattern grep Show only text that matches a pattern no-more Don't paginate output save Save output to a file
PAGE 144
! ip control-plane egress-filter ! ipv6 control-plane egress-filter ! hardware watchdog stack-unit 1 hardware watchdog stack-unit 2 hardware watchdog stack-unit 3 hardware watchdog stack-unit 4 hardware watchdog stack-unit 5 hardware watchdog stack-unit 6 ! no logging console service timestamps log datetime ! logging coredump stack-unit 1 logging coredump stack-unit 2 logging coredump stack-unit 3 logging coredump stack-unit 4 logging coredump stack-unit 5 logging coredump stack-unit 6 ! hostname ps-maa-s61
PAGE 145
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. stack-unit location-led Toggle the stack unit location LED on or off. Syntax Parameters stack-unit stack-unit-number location—led {module module-number {off | on} | off | on} stack-unit stackunit-number Enter the keywords stack-unit and the stack unit number.
PAGE 146
ipv6-address prefixlength Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults (Optional) Enter the keyword vrf then the VRF instance name. source-interface (OPTIONAL) Enter the keywords /source-interface then the interface information to include the source interface.
PAGE 147
Usage Information Version Description 8.3.12.0 Introduced on the S4810. Added support for source-interface for link-local IPv6 addressing. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series (IPv6). Increased the number of VLANs to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series (IPv4). 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and added support for IPv6 address on the E-Series only.
PAGE 148
terminal length Configure the number of lines displayed on the terminal screen. Syntax terminal length screen-length Parameters Defaults screen-length Enter a number of lines. Entering zero causes the terminal to display without pausing. The range is from 0 to 512. 24 lines Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 149
ip-address Enter the IP address of the device in dotted decimal format. ipv6-address Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing connectivity. NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults Command Modes Command History Usage Information • Timeout = 5 seconds • Probe count = 3 • 30 hops max • 40 byte packet size • UDP port = 33434 • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 150
For IPv6, you are prompted for a minimum hop count (default is 1) and a maximum hop count (default is 64). Example (IPv4) Dell# traceroute www.Dell Networking.com Translating "www.Dell Networking.com"...domain server (10.11.0.1) [OK] Type Ctrl-C to abort. ----------------------------------------------Tracing the route to www.Dell Networking.com (10.11.84.18), 30 hops max, 40 byte packets ----------------------------------------------TTL Hostname Probe1 Probe2 Probe3 1 10.11.199.190 001.000 ms 001.
PAGE 151
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 152
Usage Information 152 Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. The write memory command saves the running-configuration to the file labeled startup-configuration.
PAGE 153
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking OS supports remote authentication dial-in service (RADIUS) and active directory environments using 802.
PAGE 154
• dot1x port-control • dot1x profile • dot1x quiet-period • dot1x reauthentication • dot1x reauth-max • dot1x server-timeout • dot1x static-mab • dot1x supplicant-timeout • dot1x tx-period • show dot1x cos-mapping interface • show dot1x interface • show dot1x profile debug dot1x Display 802.1X debugging information. Syntax debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface] Parameters all Enable all debugs in dot1x.
PAGE 155
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series. dot1x auth-fail-vlan Configure an authentication failure VLAN for users and devices that fail 802.1X authentication. Syntax dot1x auth-fail-vlan vlan-id [max-attempts number] To delete the authentication failure VLAN, use the no dot1x auth-fail-vlan vlan-id [maxattempts number] command. Parameters vlan-id Enter the VLAN Identifier. The range is from 1 to 4094.
PAGE 156
After the authentication VLAN is assigned, the port-state must be toggled to restart authentication. Authentication occurs at the next reauthentication interval (dot1x reauthentication). Related Commands • dot1x port-control — enable port control on an interface • dot1x guest-vlan — configure a guest VLAN for limited access users or for devices that are not 802.1X capable. • show dot1x interface — display the 802.1X configuration of an interface.
PAGE 157
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000.
PAGE 158
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.
PAGE 159
Related Commands Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. • dot1x authentication (Configuration) — enable dot1x globally. dot1x critical-vlan Configure critical-VLAN for users or devices when authentication server is not reachable. Syntax Parameters [no] dot1x critical-vlan vlan-id vlan-id Defaults Not Configured.
PAGE 160
Auth-Fail VLAN id: Auth-Fail Max-Attempts: Critical VLAN: Critical VLAN id: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: 400 3 Enable 400 Disable Disable 30 seconds 60 seconds 2 30 seconds 30 seconds 60 seconds 2 SINGLE_HOST Authenticated Idle dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.1X capable.
PAGE 161
If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable. Therefore, a guest VLAN is allocated to the interface and authentication, for the device, occurs at the next reauthentication interval (dot1x reauthentication). If the host fails authentication for the designated number of times, the authenticator places the port in authentication failed VLAN (dot1x auth-fail-vlan).
PAGE 162
Usage Information Related Commands Version Description 8.4.1.0 Added the multi-auth option on the C-Series and S-Series. 8.3.2.0 Added the single-host and multi-host options on the C-Series, E-Series, and SSeries. • Single-host mode authenticates only one host per authenticator port and drops all other traffic on the port. • Multi-host mode authenticates the first host to respond to an Identity Request and then permits all other traffic on the port.
PAGE 163
Dell(conf-dot1x-profile)#show config dot1x profile mySupplicants mac 00:50:56:aa:01:10 mac 00:50:56:aa:01:11 Dell(conf-dot1x-profile)# Dell(conf-dot1x-profile)#exit dot1x mac-auth-bypass Enable MAC authentication bypass. If 802.1X times out because the host did not respond to the Identity Request frame, Dell Networking OS attempts to authenticate the host based on its MAC address. Syntax dot1x mac-auth-bypass To disable MAC authentication bypass on a port, use the no dot1x mac-auth-bypass command.
PAGE 164
Parameters number Enter the number of times an EAP request is transmitted before a session time-out. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 165
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series. • dot1x host-mode — enable single-host or multi-host authentication.
PAGE 166
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. The authenticator completes authentication only when you set port-control to auto. dot1x profile Configure a dot1x profile to define a list of trusted supplicant MAC addresses.
PAGE 167
dot1x quiet-period Set the number of seconds that the authenticator remains quiet after a failed authentication with a client. Syntax dot1x quiet-period seconds To disable quiet time, use the no dot1x quiet-time command. Parameters seconds Enter the number of seconds. The range is from 1 to 65535. The default is 60. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 168
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 169
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x server-timeout Configure the amount of time after which exchanges with the server time-out.
PAGE 170
Usage Information When you configure the dot1x server-timeout value, take into account the communication medium used to communicate with an authentication server and the number of RADIUS servers configured. Ideally, the dot1x server-timeout value (in seconds) is based on the configured RADIUS-server timeout and retransmit values and calculated according to the following formula: dot1x server-timeout seconds > (radius-server retransmit seconds + 1) * radius-server timeout seconds.
PAGE 171
Dot1x Status: Port Control: Port Auth Status: Re-Authentication: Untagged VLAN id: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Critical VLAN: Critical VLAN id: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Static-MAB: Static-MAB Profile: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Enable AUTO AUTHORIZED (STATIC-MAB) Enable 400 Enable 400 Enable 400 3 Enable 400 Disable Di
PAGE 172
Version Description 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x tx-period Configure the intervals at which EAPOL PDUs the Authenticator PAE transmits. Syntax dot1x tx-period seconds To return to the default, use the no dot1x tx-period command. Parameters seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535. The default is 30.
PAGE 173
Parameters interface mac-address Defaults Command Modes Command History Usage Information Enter one of the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 174
Dot1p 0 1 2 3 4 5 6 7 Dell# Remapped Dot1p 7 6 5 4 3 2 1 0 Dell# show dot1x cos-mapping interface tengigabitethernet 1/1/1/1 mac-address 00:00:00:00:00:10 Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.1p CoS re-map table on Te 1/1/1/1: ---------------------------------802.1p CoS re-map table for Supplicant: 00:00:00:00:00:10 Dot1p 0 1 2 3 4 5 6 7 Dell# Remapped Dot1p 7 6 5 4 3 2 1 0 show dot1x interface Display the 802.1X configuration of an interface.
PAGE 175
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 176
802.
PAGE 177
show dot1x profile Display all the dot1x profiles or the details of a specific profile configured in the system. Syntax Parameters show dot1x profile profile-name profile-name Specify a static dot1x profile-name. The maximum character limit for a profile name is 32 characters. Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 178
6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell Networking OS.
PAGE 179
• permit icmp (for Extended IP ACLs) • permit udp (for Extended IP ACLs) • permit (for Extended IP ACLs) • permit (for Standard MAC ACLs) • seq (for Standard MAC ACLs) • permit tcp (for Extended IP ACLs) • seq arp (for Extended MAC ACLs) • seq ether-type (for Extended MAC ACLs) • seq (for IP ACLs) • seq (for IPv6 ACLs) • permit (for IPv6 ACLs) • deny arp (for Extended MAC ACLs) • deny (for IPv6 ACLs) Commands Common to all ACL Types The following commands are available within each
PAGE 180
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced on the E-Series. The remark command is available in each ACL mode.
PAGE 181
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.19.
PAGE 182
ipv4 Enter the keyword ipv4 to configure an IPv4 access class. ipv6 Enter the keyword ipv6 to configure an IPv6 access class. Defaults Not configured. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 183
Similarly, if you have configured either IPv4 or IPv6 specific filtering on a terminal line, you cannot apply generic IP ACLs on top of this configuration. Before applying the generic ACL configuration, first undo the existing configuration using the no access-class access-list-name [ipv4 | ipv6] command. clear counters ip access-group Erase all counters maintained for access lists.
PAGE 184
To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} command. Parameters access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 185
Usage Information You can assign one ingress ACL and one egress ACL to an interface. NOTE: If you apply outbound(egress) IP acl on a switch port, the filter applies only for routed traffic egressing out of that port. To associate an access-list to a non-default VRF, use the vrf attribute of this command. You can use this command at the interface context (physical/LAG) to apply the access-list to a range of VRFs. The VRF MODE is not available for the default and management VRFs.
PAGE 186
Command Modes Command History 186 cam_count List the count of the CAM rules for this ACL. interface interface Enter the keyword interface then the one of the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 187
Usage Information NOTE: The vrf option is available only when VRF feature is enabled. show ip accounting access-lists Description “Extended IP...” Displays the name of the IP ACL. “seq 5...” Displays the filter. If the keywords count or byte were configured in the filter, the number of packets or bytes the filter processes is displayed at the end of the line. “order 4” Displays the QoS order of priority for the ACL entry.
PAGE 188
numbers have higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). monitor (OPTIONAL) Enter the keyword monitor then the session–ID to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. The session–ID range is from 0 to 65535. NOTE: For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell Networking OS Configuration Guide.
PAGE 189
Related Commands • ip access-list standard — configure a standard ACL. • permit — configure a permit filter. ip access-list standard Create a standard IP access list (IP ACL) to filter based on IP address. Syntax ip access-list standard access-list-name To delete an access list, use the no ip access-list standard access-list-name command. Parameters access-list-name Enter a string up to 140 characters long as the ACL name.
PAGE 190
The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer to your line card documentation. Example Dell(conf)# ip access-list standard TestList Dell(config-std-nacl)# Related Commands • ip access-list extended — create an extended access list. • show config — display the current configuration. permit To permit packets from a specific source IP address to leave the switch, configure a filter.
PAGE 191
no-drop Enter the keywords no-drop to match only the forwarded packets. Defaults Not configured. Command Modes CONFIGURATION-STANDARD-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 192
Defaults access-list-name Enter the name of a configured IP access list. StartingSeqNum Enter the starting sequence number to resequence. The range is from 0 to 4294967290. Step-to-Increment Enter the step to increment the sequence number. The range is from 1 to 4294967290. None Command Modes Command History Usage Information • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 193
Parameters sequence-number Enter a number from 0 to 4294967290. deny Enter the keyword deny to configure a filter to drop packets meeting this condition. permit Enter the keyword permit to configure a filter to forward packets meeting this criteria. source Enter an IP address in dotted decimal format of the network from which the packet was received. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.
PAGE 194
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 195
To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {ip | ip-protocol-number} {source mask | any | host ip-address} {destination mask | any | host ip-address} command. ip Enter the keyword ip to configure a generic IP access list. The keyword ip specifies that the access list denies all IP protocols.
PAGE 196
Usage Information Version Description 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 197
• Parameters Use the no deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter.
PAGE 198
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only.
PAGE 199
port port • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command) Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is from 0 to 65535.
PAGE 200
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 201
1 0000000000000000 1111110000000000 0 1023 1024 Total Ports: 1024 Related Commands • deny — assign a filter to deny IP traffic. • deny udp — assign a filter to deny UDP traffic. deny udp To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 202
order numbers have a higher priority) If you did not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments. monitor (OPTIONAL) Enter the keyword monitor then the session–ID to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. The session–ID range is from 0 to 65535.
PAGE 203
The C-Series and S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt or range) may require more than one entry.
PAGE 204
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 205
destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets processed by the filter. bytes (OPTIONAL) Enter the keyword bytes to count bytes processed by the filter. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 206
Usage Information Version Description 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only. For more information, see the “Quality of Service” section of the Dell Networking OS Configuration Guide. The software cannot count both packets and bytes; when you enter the count byte options, only bytes are incremented. Related Commands • ip access-list extended — create an extended ACL.
PAGE 207
port port • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port parameter) Enter the application layer port number. Enter two port numbers if you are using the range logical operand. The range is from 0 to 65535. The following list includes some common TCP port numbers: • 23 = Telnet • 20 and 21 = FTP • 25 = SMTP • 169 = SNMP destination Enter the IP address of the network or host to which the packets are sent.
PAGE 208
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option.
PAGE 209
Related Commands • ip access-list extended — create an extended ACL. • permit — assign a permit filter for IP packets. • permit udp — assign a permit filter for UDP packets. permit udp To pass UDP packets meeting the filter criteria, configure a filter.
PAGE 210
monitor (OPTIONAL) Enter the keyword monitor then the session–ID to describe the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. The session–ID range is from 0 to 65535. For more information, see “Flow-based Monitoring” in the Port Monitoring section of the Dell Networking OS Configuration Guide. no-drop Enter the keywords no-drop to match only the forwarded packets. Defaults Not configured.
PAGE 211
Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry. The range of ports is configured in the CAM based on bit mask boundaries; the space required depends on exactly what ports are included in the range. Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 212
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series (IPv4). 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.
PAGE 213
mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host and then enter the IP address to specify a host IP address or hostname.
PAGE 214
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 215
NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value. Configure packet counters with logging instead. Related Commands • deny — configure a filter to drop packets. • permit — configure a filter to forward packets. Extended IPv6 ACL Commands The following commands configure extended IPv6 ACLs. deny Configure a filter that drops IPv6 packets that match the filter criteria.
PAGE 216
deny icmp Configure a filter to drop all or specific ICMP messages.
PAGE 217
deny tcp Configure a filter that drops TCP packets that match the filter criteria.
PAGE 218
• fin: finish (no more data from the user) • psh: push function • rst: reset the connection • syn: synchronize sequence numbers • urg: urgent field count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. Defaults Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific.
PAGE 219
Total Ports: 1024 Related Commands deny – assigns a filter to deny IP traffic. deny udp – assigns a filter to deny UDP traffic. deny udp Configure a filter to drop user datagram protocol (UDP) packets meeting the filter criteria.
PAGE 220
byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. Defaults Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the S-Series. 8.2.1.
PAGE 221
ipv6 access-list Configure an access list based on IPv6 addresses or protocols. Syntax ipv6 access-list access-list-name cpu-qos To delete an access list, use the no ipv6 access-list access-list-name command. Parameters access-list-name Enter the access list name as a string, up to 140 characters. cpu-qos Enter the keyword cpu-qos to assign this ACL to control plane traffic only (CoPP). permit Enter the keyword permit to configure a filter to forward packets meeting this condition.
PAGE 222
Usage Information Version Description 7.4.1.0 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification on entries allowed per ACL, refer to your line card documentation. You can create an IPv6 ACL for control-plane traffic policing for OSPFv3, in addition to the CoPP support for VRRP, BGP, and ICMP. permit To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP.
PAGE 223
permit tcp Configure a filter to pass TCP packets that match the filter criteria. Syntax permit tcp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [bit] [operator port [port]] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 224
• psh: push function • rst: reset the connection • syn: synchronize sequence numbers • urg: urgent field count (OPTIONAL) Enter the keyword count to count packets processed by the filter. byte (OPTIONAL) Enter the keyword byte to count bytes processed by the filter. Defaults Not configured. Command Modes ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 225
permit udp – assigns a permit filter for UDP packets. permit udp Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [operator port [port]] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 226
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series TeraScale. Added the monitor option. Usage Information Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (gt, lt, range) may require more than one entry.
PAGE 227
Parameters Defaults Command Modes Command History Usage Information ipv4 | ipv6 | mac Enter the keyword ipv4, ipv6 or mac to identify the access list type to resequence. access-list-name Enter the name of a configured IP access list, up to 140 characters. Increased name string to accept up to 140 characters. Prior to version 7.8.1.0, names are up to 16 characters long. StartingSeqNum Enter the starting sequence number to resequence. The range is 0 to 4294967290.
PAGE 228
icmp Enter the keyword icmp to configure an Internet Control Message Protocol version 6 filter. ipv6 Enter the keyword ipv6 to configure any Internet Protocol version 6 filter. tcp Enter the keyword tcp to configure a Transmission Control protocol filter. udp Enter the keyword udp to configure a User Datagram Protocol filter. source address Enter the IPv6 address of the network or host from which the packets were sent in the x:x:x:x::x format followed by the prefix length in the /x format.
PAGE 229
Related Commands 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.0.2.0 Introduced on the S6000. 8.4.2.1 Introduced on the E-Series TeraScale and S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. deny – configures a filter to drop packets. permit – configures a filter to forward packets.
PAGE 230
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. mac access-group Apply a MAC ACL to traffic entering or exiting an interface. You can apply a MAC ACL on a physical, port-channel, or VLAN interface.
PAGE 231
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 232
in | out • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. • For a port-channel interface, enter the keywords port-channel then the portchannel ID. Identify whether ACL is applied on ingress or egress side. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 233
in | out Command Modes Command History • EXEC • EXEC Privilege • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Identify whether ACL is applied on ingress or egress side. This guide is platform-specific.
PAGE 234
Standard MAC ACL Commands When you create an access control list without any rule and then apply it to an interface, the ACL behavior reflects implicit permit. These commands configure standard MAC ACLs and support both Ingress and Egress MAC ACLs. NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets with a the MAC address specified, configure a filter.
PAGE 235
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. When you use the log option, the CP processor logs detail the packets that match.
PAGE 236
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 237
threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The threshold range is from 1 to 10 minutes.
PAGE 238
seq To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny {any | mac-source-address mac-source-address-mask} command.
PAGE 239
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs details about the packets that match.
PAGE 240
Parameters any Enter the keyword any to drop all packets. host mac-address Enter the keyword host and then enter a MAC address to drop packets with that host address. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask Specify which bits in the MAC address must match. The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly.
PAGE 241
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 242
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 243
permit To pass packets matching the criteria specified, configure a filter. Syntax permit {any | host mac-address | mac-source-address mac-source-address-mask} {any | host mac-address | mac-destination-address mac-destination-address-mask} [ethertype operator] [count [byte]] | [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 244
Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 245
clear ip prefix-list Reset the number of times traffic mets the conditions (“hit” counters) of the configured prefix lists. Syntax Parameters clear ip prefix-list [prefix-name] prefix-name (OPTIONAL) Enter the name of the configured prefix list to clear only counters for that prefix list, up to 140 characters long. Defaults Clears “hit” counters for all prefix lists unless a prefix list is specified. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 246
To delete a drop filter, use the no deny ip-prefix command. Parameters ip-prefix Specify an IP prefix in the network/length format. For example, 35.0.0.0/ 8 means match the first 8 bits of address 35.0.0.0. ge min-prefixlength (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32. le max-prefix-length (OPTIONAL) Enter the keyword le and then enter the maximum prefix length, which is a number from zero (0) to 32. Defaults Not configured.
PAGE 247
Parameters prefix-name Enter a string up to 16 characters long as the name of the prefix list, up to 140 characters long. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 248
permit Enter the keyword permit to configure a filter to forward packets meeting this condition. any (OPTIONAL) Enter the keyword any to match any packets. ip-prefix /nn (OPTIONAL) Specify an IP prefix in the network/length format. For example, 35.0.0.0/8 means match the first 8 bits of address 35.0.0.0. ge min-prefixlength (OPTIONAL) Enter the keyword ge and then enter the minimum prefix length, which is a number from zero (0) to 32.
PAGE 249
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 250
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 251
Example Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 252
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 253
description Add a description to this route map. Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the route map (80 characters maximum). Defaults None Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 254
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 255
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 256
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 257
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 258
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 259
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 260
Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 261
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 262
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 263
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 264
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 265
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 266
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 267
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 268
All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to drop all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. none Enter the keyword none to remove the community attribute from routes meeting the route map criteria.
PAGE 269
To remove a set level condition, use the no set level {backbone | level-1 | level-1-2 | level-2 | stub-area} command. Parameters backbone Enter the keyword backbone to redistribute matched routes to the OSPF backbone area (area 0.0.0.0). level-1 Enter the keyword level-1 to redistribute matched routes to IS-IS Level 1. level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2.
PAGE 270
set local-preference To set the BGP LOCAL_PREF attribute for routers within the local autonomous system, configure a filter. Syntax set local-preference value To delete a BGP LOCAL_PREF attribute, use the no set local-preference command. Parameters value Enter a number as the LOCAL_PREF attribute value. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 271
To delete a setting, enter no set metric. Parameters + (OPTIONAL) Enter + to add a metric-value to the redistributed routes. - (OPTIONAL) Enter - to subtract a metric-value from the redistributed routes. metric-value Enter a number as the new metric value. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 272
Parameters internal Enter the keyword internal to assign the Interior Gateway Protocol metric of the next hop as the route’s BGP MULTI_EXIT_DES (MED) value. external Enter the keyword external to assign the IS-IS external metric. type-1 Enter the keyword type-1 to assign the OSPF Type 1 metric. type-2 Enter the keyword type-2 to assign the OSPF Type 2 metric. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 273
Parameters ip-address Specify an IP address in dotted decimal format. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 274
incomplete Enter the keyword incomplete to set routes with incomplete routing information. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 275
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 276
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 277
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell(conf-nprefixl)# show config ! ip prefix-list PL_OSPF_to_RIP seq 5 permit 1.1.1.0/24 seq 10 deny 2.1.0.0/16 ge 23 seq 25 permit 192.0.0.0 bitmask 192.0.0.0 Dell(conf-nprefixl)# show route-map Display the current route map configurations.
PAGE 278
Example Version Description pre-6.1.1.0 Introduced on the E-Series. Dell# show route-map route-map firpo, permit, sequence 10 Match clauses: Set clauses: tag 34 Dell# Related Commands • route-map — configure a route map. deny (for Standard IP ACLs) To drop packets with a certain IP address, configure a filter.
PAGE 279
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 280
of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 281
• deny udp — assign a filter to deny UDP packets. • ip access-list extended — create an extended ACL. seq (for Standard IPv4 ACLs) Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {source [mask] | any | host ip-address}} [count [bytes]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To delete a filter, use the no seq sequence-number command.
PAGE 282
count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 283
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 284
To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny ether-type protocol-type-number {destination-mac-address macaddress-mask | any} vlan vlan-id {source-mac-address mac-address-mask | any} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 285
egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 286
Usage Information Version Description 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 287
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 288
permit (for Standard IP ACLs) To permit packets from a specific source IP address to leave the switch, configure a filter. Syntax permit {source [mask]| any | host ip-address} [count [byte]] [dscp value] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit {source [mask] | any | host ip-address} command.
PAGE 289
count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 290
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 291
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 292
permit icmp (for Extended IP ACLs) Configure a filter to allow all or specific ICMP messages. Syntax permit icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [dscp] [count [byte]] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 293
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 294
Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 295
• Parameters Defaults Use the no deny {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 296
traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). Related Commands • ip access-list extended — create an extended ACL.
PAGE 297
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 298
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.
PAGE 299
[count [byte]] [order] [fragments] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit tcp {source mask | any | host ip-address} {destination mask | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 300
can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode. When you enable this capability, traffic with particular flows that are traversing through the ingress and egress interfaces are examined and, appropriate ACLs can be applied in both the ingress and egress direction.
PAGE 301
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3.0.
PAGE 302
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. You can enter a threshold in the range of 1-100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. You can enter an interval in the range of 1-10 minutes.
PAGE 303
seq (for IP ACLs) Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter.
PAGE 304
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 305
Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 306
Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. no-drop Enter the keywords no-drop to match only the forwarded packets.
PAGE 307
deny arp (for Extended MAC ACLs) Configure an egress filter that drops ARP packets on egress ACL supported line cards. (For more information, refer to your line card documentation).
PAGE 308
count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 309
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 310
7 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 311
ROUTER OSPFv3 ROUTER BGP ROUTER ISIS Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.2) Introduced support for enabling BFD on nondefault VRFs for OSPFv2 on the S3048–ON, S4048–ON, S4048T-ON, S6010–ON, Z9100–ON, and S6100–ON. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.
PAGE 312
You can enable BFD on a nondefault VRF for OSPFv2. Related Commands • neighbor bfd disable — disable a BFD session explicitly with a BGP neighbor or a BGP peer group. ip route bfd Enable BFD for all neighbors configured through static routes.
PAGE 313
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.3.(0.0) Introduced on S6000. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on Z9000, S4810, and S4820T. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. neighbor bfd Explicitly enable a BFD session with a BGP neighbor or a BGP peer group.
PAGE 314
Related Commands • The neighbor does not inherit the global BFD enable values configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs. • The neighbor only inherits the global timer values configured with the bfd neighbor command: interval, min_rx, and multiplier. • neighbor bfd disable — disable a BFD session explicitly with a BGP neighbor or a BGP peer group. neighbor bfd disable Explicitly disable a BFD session with a BGP neighbor or a BGP peer group.
PAGE 315
BFD session parameters globally configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs. Related Commands • neighbor bfd — enable a BFD session explicitly with a BGP neighbor or a BGP peer group. show bfd neighbors Display BFD neighbor information on all interfaces or a specified interface.
PAGE 316
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Added support for BFD for BGP on the S4810. 8.4.1.3 Added support for BFD for BGP on the E-Series. 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series. 7.5.1.0 Added support for BFD for VLAN and port-channel interfaces on the E-Series. 7.4.1.0 Introduced BFD on physical ports on the E-Series.
PAGE 317
Client Registered: OSPF Uptime: 00:00:15 Statistics: Number of packets received from neighbor: 78 Number of packets sent to neighbor: 78 Number of state changes: 1 Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 4 Session Discriminator: 7 Neighbor Discriminator: 2 Local Addr: 6.1.1.1 Local MAC Addr: 00:a0:c9:00:00:02 Remote Addr: 6.1.1.
PAGE 318
8 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 319
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.5.1.
PAGE 320
• Command History Usage Information ROUTER BGP ADDRESS FAMILY IPv6 This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 321
Parameters Defaults Command Modes Command History Related Commands send Enter the keyword send to indicate that the system sends multiple paths to peers. receive Enter the keyword receive to indicate that the system accepts multiple paths from peers. both Enter the keyword both to indicate that the system sends and accepts multiple paths from peers. path-count Enter the number paths supported. The range is from 2 to 64.
PAGE 322
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced command. 7.7.1.0 Introduced on the C-Series. Any update without a MED attribute is the least preferred route.
PAGE 323
Usage Information Before enabling this feature, enable the enable bgp four-octet-as-supportcommand. If you disable the four-octect-support command after using dot or dot+ format, the AS numbers revert to asplain text. When you apply an asnotation, it is reflected in the running-configuration. If you change the notation type, the running-config updates dynamically and the new notation shows.
PAGE 324
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enable this command, use the clear ip bgp * command to recompute the best path.
PAGE 325
bgp bestpath med confed Enable MULTI_EXIT_DISC (MED) attribute comparison on paths learned from BGP confederations. Syntax bgp bestpath med confed To disable MED comparison on BGP confederation paths, enter the no bgp bestpath med confed command. Defaults Disabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.8(0.
PAGE 326
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 6.3.1.
PAGE 327
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced Configuring this option retains the current best-path. When sessions are then reset, the oldest received path is chosen as the best-path. bgp client-to-client reflection Allows you to enable route reflection between clients in a cluster. Syntax bgp client-to-client reflection To disable client-to-client reflection, use the no bgp client-to-client reflection command.
PAGE 328
bgp cluster-id Assign a cluster ID to a BGP cluster with more than one route reflector. Syntax bgp cluster-id {ip-address | number} To delete a cluster ID, use the no bgp cluster-id {ip-address | number} command. Parameters ip-address Enter an IP address as the route reflector cluster ID. number Enter a route reflector cluster ID as a number from 1 to 4294967295. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 329
bgp confederation identifier Configure an identifier for a BGP confederation. Syntax bgp confederation identifier as-number To delete a BGP confederation identifier, use the no bgp confederation identifier as-number command. Parameters as-number Enter the AS number. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.1 to 65535.65535 (dotted format). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 330
This command automatically restarts the BGP instance for the configuration to take effect. Related Commands • bgp four-octet-as-support — enable 4-byte support for the BGP process. bgp confederation peers Specify the autonomous systems (ASs) that belong to the BGP confederation. Syntax bgp confederation peers as-number [...as-number] To return to the default, use the no bgp confederation peers command. Parameters as-number Enter the AS number.
PAGE 331
• bgp four-octet-as-support — enable 4-byte support for the BGP process. bgp dampening Enable BGP route dampening and configure the dampening parameters. Syntax bgp dampening [half-life reuse suppress max-suppress-time] [route-map map-name] To disable route dampening, use the no bgp dampening [half-life reuse suppress maxsuppress-time] [route-map map-name] command. Parameters half-life (OPTIONAL) Enter the number of minutes after which the Penalty is decreased.
PAGE 332
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enter the bgp dampening command, the default values for half-life, reuse, suppress, and maxsuppress-time are applied. The parameters are position-dependent; therefore, if you configure one parameter, configure the parameters in the order they appear in the CLI. Route refresh is sent when you enable BGP dampening.
PAGE 333
Usage Information Related Commands All routers apply the bgp default local-preference command setting within the AS. To set the local preference for a specific route, use the set local-preference command in ROUTE-MAP mode. • set local-preference — assign a local preference value for a specific route. bgp dmzlink-bw Enables BGP Link Bandwidth. Syntax bgp dmzlink-bw To disable BGP Link Bandwidth, enter the no bgp dmzlink-bw command.
PAGE 334
bgp enforce-first-as Disable (or enable) enforce-first-as check for updates received from EBGP peers. Syntax bgp enforce-first-as To turn off the default, use the no bgp enforce-first-as command. Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 335
bgp fast-external-fallover Enable the fast external fallover feature, which immediately resets the BGP session if a link to a directly connected external peer fails. Syntax bgp fast-external-fallover To disable fast external fallover, use the no bgp fast-external-fallover command. Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 336
Defaults Disabled (supports 2–byte format) Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500.
PAGE 337
stale-path-time seconds Enter the keyword stale-path-time then the maximum number of seconds to wait before restarting a peer’s stale paths. The default is 360 seconds. role receiver-only Enter the keyword role receiver-only to designate the local router to support graceful restart as a receiver only. Defaults as above Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 338
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 339
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced. This command is a knob to disable BGP next-hop resolution using BGP learned routes.
PAGE 340
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced BGP uses regular expressions (regex) to filter route information. In particular, the use of regular expressions to filter routes based on AS-PATHs and communities is common.
PAGE 341
Defaults The router ID is the highest IP address of the Loopback interface or, if no Loopback interfaces are configured, the highest IP address of a physical interface on the router. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 342
NOTE: If you enter the clear ip bgp ip-address soft command, both inbound and outbound policies are reset. in (OPTIONAL) Enter the keyword in to activate only inbound policies. out (OPTIONAL) Enter the keyword out to activate only outbound policies. NOTE: You must execute the clear ip bgp soft out command when ever there is a change in the local policy.
PAGE 343
clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state. Syntax Parameters clear ip bgp [vrf vrf-name] [ipv4 [multicast | unicast] | ipv6 unicast] [dampening [ipv4-address mask | ipv6–address mask] ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to clear dampening information only that BGP neighbor.
PAGE 344
clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap. Syntax clear ip bgp [vrf vrf-name] [ipv4 [multicast | unicast] | ipv6 unicast] [flapstatistics [ipv4-address mask | ipv6–address mask] | filter-list as-path-name | regexp regular-expression] Parameters ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to reset only that prefix.
PAGE 345
Usage Information Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enter the clear ip bgp flap-statistics command without any parameters, all statistics are cleared. • show debugging — view the enabled debugging operations. • show ip bgp flap-statistics — view the BGP flap statistics.
PAGE 346
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. debug ip bgp Display all information on BGP, including BGP events, keepalives, notifications, and updates. Syntax debug ip bgp [ vrf vrf-name | A.B.C.
PAGE 347
soft-reconfiguration Enter the keywords soft-reconfiguration to view only information on inbound BGP soft reconfiguration. updates Enter the keyword updates to view BGP updates. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 348
Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 unicast routes.
PAGE 349
Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP state changes corresponding to that VRF. A.B.C.D (OPTIONAL) Enter the IPv4 address of the neighbor. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peergroup-name (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only events on inbound BGP messages.
PAGE 350
Parameters A.B.C.D (OPTIONAL) Enter the IPv4 address of the neighbor. X:X:X:X::X (OPTIONAL) Enter an IPv6 address. peer-group peergroup-name (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only inbound keepalive messages. out (OPTIONAL) Enter the keyword out to view only outbound keepalive messages. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 351
out (OPTIONAL) Enter the keyword out to view BGP notifications sent to neighbors Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added ipv6 support.
PAGE 352
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 353
prefix-list prefix-listname (OPTIONAL) Enter the keyword prefix-list then the name of an established prefix list. If the prefix list is not configured, the default is permit (to allow all routes). ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group to disable or enable all routers within the peer group. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 354
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 355
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series and Z9500. • permit bandwidth – specify link band width extended-community attribute as the matching criteria to permitting incoming or outgoing traffic. description Enter a description of the BGP routing protocol. Syntax description {description} To remove the description, use the no description {description} command.
PAGE 356
maximum-paths Configure the maximum number of parallel routes (multipath support) BGP supports. Syntax maximum-paths {ebgp | ibgp} number To return to the default values, enter the no maximum-paths command. Parameters ebgp Enter the keyword ebgp to enable multipath support for External BGP routes. ibgp Enter the keyword ibgp to enable multipath support for Internal BGP routes. number Enter a number as the maximum number of parallel paths.
PAGE 357
neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/Subsequent Address Family Identifier). Syntax neighbor [ip-address | peer-group-name] activate To disable, use the no neighbor [ip-address | peer-group-name] activate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group.
PAGE 358
neighbor add-path This command allows the specified neighbor/peer group to send/receive multiple path advertisements. Syntax neighbor [ip-address | peer-group-name] add-path [send | receive | both] pathcount Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name (OPTIONAL) Enter the name of the peer group. send Enter the keyword send to indicate that the system sends multiple paths to peers.
PAGE 359
To return to the default value, use the no neighbor {ip-address | peer-group-name} advertisement-interval command. Parameters Defaults ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. seconds Enter a number as the time interval, in seconds, between BGP advertisements. The range is from 0 to 600 seconds.
PAGE 360
seconds Enter a number as the time interval, in seconds, before BGP route updates are sent. The range is from 0 to 3600 seconds. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 361
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 362
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 363
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 364
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 365
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 366
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.4.1.0 Introduced When you enable failover, BGP keeps track of IP or IPv6 ability to reach the peer remote address and the peer local address.
PAGE 367
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If a local-as is configured, BGP does not allow for the configuration of BGP confederation. Similarly, if BGP confederation is configured, then BGP does not allow the configuration of local-as.
PAGE 368
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 369
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 370
To disable dmzlink-dw for the peer group, use the no neighbor ip-address dmzlink-dw command. Parameters ip-address Enter the IP address of the router to be included in the peer group. peer-group-name Enter the name of a configured peer group. dmzlink-bw Enter the keyword dmzlink-bw to attach a link bandwidth to received routes.
PAGE 371
In BGP, you cannot associate a peer to a peer-group without configuring the remote-as for Internal BGP (IBGP) or External BGP (EBGP). This command automatically restarts the neighbor session for the configuration to take effect. Related Commands • clear ip bgp — reset BGP sessions. • neighbor peer-group (creating group) — create a peer group. • show ip bgp peer-group — view BGP peers. • show ip bgp neighbors — view BGP neighbors configurations.
PAGE 372
• neighbor shutdown — disable a peer or peer group. neighbor peer-group passive Enable passive peering on a BGP peer group, that is, the peer group does not send an OPEN message, but responds to one. Syntax neighbor peer-group-name peer-group passive [ sessions] To delete a passive peer-group, use the no neighbor peer-group-name peer-group passive command. Parameters peer-group-name Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured.
PAGE 373
neighbor remote-as Create and specify the remote peer to the BGP neighbor. Syntax neighbor {ip-address | peer-group-name} remote-as number To delete a remote AS entry, use the no neighbor {ip-address | peer-group-name} remote-as number command. Parameters ip-address Enter the IP address of the neighbor to enter the remote AS in its routing table. peer-group-name Enter the name of the peer group to enter the remote AS into routing tables of all routers within the peer group.
PAGE 374
• bgp four-octet-as-support — enable 4-byte support for the BGP process. neighbor remove-private-as Remove private AS numbers from the AS-PATH of outgoing updates. Syntax neighbor {ip-address | peer-group-name} remove-private-as To return to the default, use the no neighbor {ip-address | peer-group-name} removeprivate-as command. Parameters ip-address Enter the IP address of the neighbor to remove the private AS numbers.
PAGE 375
neighbor route-map Apply an established route map to either incoming or outbound routes of a BGP neighbor or peer group. Syntax neighbor {ip-address | peer-group-name} route-map map-name {in | out} To remove the route map, use the no neighbor {ip-address | peer-group-name} route-map map-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. map-name Enter the name of an established route map.
PAGE 376
If you identify a peer group by name, the peers in that peer group inherit the characteristics in the Route map used in this command. If you identify a peer by IP address, the Route map overwrites either the inbound or outbound policies on that peer. neighbor route-reflector-client Configure the router as a route reflector and the specified neighbors as members of the cluster.
PAGE 377
The first time you enter this command, the router configures as a route reflector and the specified BGP neighbors configure as clients in the route-reflector cluster. When you remove all clients of a route reflector using the no neighbor route-reflector-client command, the router no longer functions as a route reflector.
PAGE 378
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To configure a COMMUNITY attribute, use the set community command in ROUTE-MAP mode. In order that settings corresponding to the neighbor send-community command take effect, you must execute the clear ip bgp command immediately after you execute the neighbor send-community command.
PAGE 379
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group. Use this command with caution as it terminates the specified BGP sessions. When a neighbor or peer group is shut down, use the show ip bgp summary command to confirm its status.
PAGE 380
Usage Information Version Description 7.4.1.0 Introduced. This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group. Similarly, you cannot associate a peer to a peer group if that peer is already configured with these settings. CAUTION: Inbound update storage is a memory-intensive operation.
PAGE 381
Usage Information Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Timer values configured with the neighbor timers command override the timer values configured with any other command.
PAGE 382
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Loopback interfaces are up constantly and the BGP session may need one interface constantly up to stabilize the session.
PAGE 383
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In the Dell Networking OS best path selection process, the path with the highest weight value is preferred. NOTE: In the Dell Networking OS best-path selection process, the path with the highest weight value is preferred.
PAGE 384
If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 385
To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted decimal format of the network. mask Enter the mask of the IP address in the slash prefix length format (for example, /24). The mask appears in command outputs in dotted decimal format (A.B.C.D). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 386
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series.
PAGE 387
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 388
redistribute ospf Redistribute OSPF routes into BGP. Syntax redistribute ospf process-id [[match external {1 | 2}] [match internal]] [route-map map-name] To stop redistribution of OSPF routes, use the no redistribute ospf process-id command. Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 | 2} (OPTIONAL) Enter the keywords match external to redistribute OSPF external routes. You can specify 1 or 2 to redistribute those routes only.
PAGE 389
Usage Information You can use the redistribute command to advertise the IGP cost as the MED on redistributed routes. When you set the route-map with metric-type internal and apply outbound to an EBGP peer/peer-group, the advertised routes corresponding to those peer/peer-groups have the IGP cost set as MED. When you enter the redistribute isis process-id command without any other parameters, Dell Networking OS redistributes all OSPF internal routes, external type 1 routes, and external type 2 routes.
PAGE 390
BGP does not allow 23456 (AS-TRANS) as a configured AS number. Example Dell(conf)# router bgp 3 Dell(conf-router_bgp)# set extcommunity bandwidth Enables you to set extended community bandwidth. Syntax set extcommunity bandwidth To disable extended community bandwidth, enter the no set extcommunity bandwidth command. Parameters bandwidth Enter the keyword bandwidth to enable extended community bandwidth. The range is from 0 to 102400.
PAGE 391
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 392
show config View the current ROUTER BGP configuration. Syntax show config Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 393
Parameters Command Modes Command History Usage Information ipv4 unicast (OPTIONAL) Enter the keywords ipv4 unicast to view information only related to ipv4 unicast routes. network (OPTIONAL) Enter the network address (in dotted decimal format) of the BGP network to view information only on that network. network-mask (OPTIONAL) Enter the network mask (in slash prefix format) of the BGP network address.
PAGE 394
Field Description Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. The show ip bgp command displays the dmzlink-dw details only if dmzlink-bw is enabled using the bgp dmzlink-dw command. Example Dell# show ip bgp BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 395
Command Modes Command History Usage Information Example ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 multicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related to only to the ipv6 unicast routes. cluster-id (OPTIONAL) Enter the cluster id in dotted decimal format. The range is 1 — 4294967295. • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 396
Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *>I 55.0.0.0/24 *>I 66.0.0.0/24 *>I 77.0.0.0/24 Next Hop 172.16.0.2 172.16.0.2 172.16.0.2 Metric LocPrf Weight Path 0 0 400 500 600 i 0 0 500 i 0 0 i Dell# show ip bgp cluster-list 4.4.4.4 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 397
All routes with the NO_ADVERTISE (0xFFFFFF02) community attribute must not be advertised to other BGP peers. no-export Enter the keywords no-export to view all routes containing the well-known community attribute of NO_EXPORT. All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. Command Modes Command History Usage Information • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 398
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network.
PAGE 399
Command Modes Command History Usage Information • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 400
Dell# show ip bgp 55.0.0.0/24 BGP routing table entry for 55.0.0.0/24 Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 172.16.0.2 (172.16.0.2) AS_PATH : 200 Best Next-Hop : 172.16.0.2, Cost : 0 Origin IGP, Metric 4294967295 (Default), LocalPref Communities : 200:1 1000:1 Dell# 100, Weight 0, external 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active).
PAGE 401
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To determine a BGP session flap, both a route-down event and a subsequent route-up event corresponding to a single route are considered. As a result, a flap event is penalized only one time during the route-down event.
PAGE 402
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 403
NdRibCtxAddrLen 255 : NdAFPrefix 0 : NdAfNLRIP 0 : NdAFNLRILen 0 : NdAFWPtrP 0 NdAFWLen 0 : NdAfNH : NdAFRedRttP 0x41a0d400 : NdRecCtxAdd 1101110868 NdRedCtxAddrLen 255 : NdAfRedMkrP 0x41a19e88 : AFAggRttP 0x41a0d600 : AfAggCtxAddr 1101111028 : AfAggrCtxAddrLen 255 AfNumAggrPfx 0 : AfNumAggrASSet 0 : AfNumSuppmap 0 : AfNumAggrValidPfx 0 : AfMPathRttP 0x41a0d700 MpathCtxAddr 1101111140 : MpathCtxAddrlen 255 : AfEorSet 0x41a19f98 : NumDfrdPfx 0 AfActPeerHd 0x41a1a3a4 : AfExtDist 1101112312 : AfIntDist 200 : A
PAGE 404
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To view the total number of COMMUNITY attributes found, use the show ip bgp summary command. The text line above the route table states the number of COMMUNITY attributes found.
PAGE 405
Command Modes Command History Usage Information Example • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 406
Dell# Dell# show ip bgp filter-list a1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 55.0.0.0/24 *> 66.0.0.0/24 Dell# Next Hop 172.16.0.2 172.16.0.
PAGE 407
Command Modes Command History Usage Information Example • EXEC • EXEC Privilege • ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified. • $ = (dollar sign) the end of the output string. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 408
*>n 66.66.77.77/32 Dell# 0.0.0.0 0 32768 i show ip bgp inconsistent-as View routes with inconsistent originating autonomous system (AS) numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path.
PAGE 409
Example Field Description LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight. Path Lists all the ASs the route passed through to reach the destination network. Dell# show ip bgp inconsistent-as BGP table version is 280852, local router ID is 10.1.2.
PAGE 410
{received-routes [network [network-mask]]} | {denied-routes [network [networkmask]]}] Parameters ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes.
PAGE 411
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Added the detail option. Output now displays the default MED value. 7.2.1.0 Added the received and denied route options. 6.3.10 The output is changed to display the total number of advertised prefixes.
PAGE 412
Example The Lines Beginning with: Description (list of inbound and outbound policies) Displays the policy commands configured and the names of the Route map, AS-PATH ACL, or Prefix list configured for the policy. For address family: Displays the IPv4 Unicast as the address family. BGP table version Displays which version of the primary BGP routing table the router and the neighbor are using.
PAGE 413
Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last reset never Local host: 172.16.0.1, Local port: 58145 Foreign host: 172.16.0.2, Foreign port: 179 Dell# Related Commands • show ip bgp — view the current BGP routing table. show ip bgp next-hop View all next hops (using learned routes only) with current reachability and flap status. This command only displays one path, even if the next hop is reachable by multiple paths.
PAGE 414
Example Field Description RefCount Displays the number of BGP routes using this next hop. Cost Displays the cost associated with using this next hop. Flaps Displays the number of times the next hop has flapped. Flaps Displays the number of times the next hop has flapped. Dell# show ip bgp next-hop Next-hop Resolved 172.16.0.2 YES Dell# show ip bgp paths View all the BGP path attributes in the BGP database.
PAGE 415
Usage Information Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF for the S4810, S4820T, and S6000. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp path command shown in the following example.
PAGE 416
• Command History Usage Information Example EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 417
Parameters Command Modes Command History Usage Information ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
PAGE 418
Example Line beginning with: Description Minimum time Displays the time interval between BGP advertisements. For address family Displays IPv4 Unicast as the address family. BGP neighbor Displays the name of the BGP neighbor. Number of peers Displays the number of peers currently configured for this peer group. Peer-group members: Lists the IP addresses of the peers in the peer group. If the address is outbound optimized, an * is displayed next to the IP address.
PAGE 419
NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. Command Modes Command History Usage Information • EXEC • EXEC Privilege • [ ] = (brackets) a range of single-character patterns. • ( ) = (parenthesis) groups a series of pattern elements to a single element. • { } = (braces) minimum and the maximum match count. • ^ = (caret) the beginning of the input string.
PAGE 420
Example Dell# show ip bgp regexp ^200 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r - redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network *> 55.0.0.0/24 *> 66.0.0.0/24 Dell# Next Hop 172.16.0.2 172.16.0.
PAGE 421
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations. When attributes that correspond to multiple routes change, then attribute counts that the show ip bgp summary command displays are calculated as summations of attributes corresponding to all the associated routes.
PAGE 422
Field Description OutQ Displays the number of messages waiting to be sent to that neighbor. If a number appears in parentheses, the number represents the number of messages waiting to be sent to the peer group. Up/Down Displays the amount of time that the neighbor is in the Established stage. If the neighbor has never moved into the Established stage, the word never is displayed.
PAGE 423
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.
PAGE 424
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 425
Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF. ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view dampened-route information related only to ipv4 unicast routes.
PAGE 426
local-distance Defaults Enter a number to assign to routes learned from networks listed in the network command. The range is from 1 to 255. The default is 200. • external-distance = 20 • internal-distance = 200 • local-distance = 200 Command Modes ROUTER BGP (conf-router_bgp_af) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 427
Command Modes Command History Usage Information ipv4 multicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword multicast to view information related only to ipv4 multicast routes. ipv4 unicast (OPTIONAL) Enter the keywords ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes.
PAGE 428
Example Dell# show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network d 55.0.0.0/24 Dell# 428 Border Gateway Protocol From 172.16.0.
PAGE 429
9 Content Addressable Memory (CAM) You can use content addressable memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance.
PAGE 430
cam-acl (Configuration) Select the default CAM allocation settings or reconfigure a new CAM allocation for Layer 2, IPv4, and IPv6 ACLs, Layer 2 and Layer 3 (IPv4) QoS, Layer 2 Protocol Tunneling (L2PT), IP and MAC source address validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, OpenFlow, and Policy-based Routing (PBR).
PAGE 431
Ipmacacl number Enter the keyword ipmacacl and then the number of FP blocks for IP and MAC ACL. The range is from 0 to 9. etsaclnumber Enter the keyword etsacl and then the number of FP blocks for ETS ACL. The range is from 0 to 9. nlbclusteracl number Enter the keyword nlbclusteracl and then the number of FP blocks for nlbcluster ACL. The range is from 0 to 9. By default, the value is 0 and it supports 8 NLB arp entries reserved for internal functionality.
PAGE 432
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Added the keyword ipv4udfmirracl. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the nlbcluster ACL keyword. Introduced on the S6000-ON. 9.4.(0.
PAGE 433
Parameters default Reset egress CAM ACL entries to default settings. l2acl number Allocate space to each CAM region. The total space allocated must equal 4. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 434
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 435
Usage Information Version Description 7.8.1.0 Introduced on the C-Series. The display reflects the settings implemented with the cam-acl command. Example test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax Parameters test cam-usage service-policy input input policy name stack-unit {number | all} policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters.
PAGE 436
The following describes the test cam-usage command shown in the following example. Example Term Explanation Stack-Unit Lists the stack unit or units that are checked. Entering all shows the status for all stacks. Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for stack-units and port-pipes in the chassis. . CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile.
PAGE 437
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.7(0.0) Introduced on the S6000, S6000-ON, and Z9500 switch..
PAGE 438
10 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 439
Version Description 8.3.8.0 Introduced on the S4810. service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax Parameters service-policy rate-limit-cpu-queues policy-name policy-name Enter the service-policy name, using a string up to 32 characters. Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific.
PAGE 440
service-policy rate-limit-protocols Apply a policy for the system to rate limit control protocols on a per-protocol basis. Syntax service-policy rate-limit-protocols policy-name Parameters policy-name Enter the service-policy name, using a string up to 32 characters. Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 441
show cpu-queue rate cp Display the rates for each CPU queue. Syntax show cpu-queue rate cp Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 442
show ip protocol-queue-mapping Display the queue mapping for each configured protocol. Syntax show ip protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example 442 Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 443
show ipv6 protocol-queue-mapping Display the queue mapping for each configured IPv6 protocol. Syntax show ipv6 protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 444
show mac protocol-queue-mapping Display the queue mapping for the MAC protocols. Syntax show mac protocol-queue-mapping Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 445
11 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic. The Dell Networking OS commands for data center bridging features include 802.1Qbb priority-based flow control (PFC), 802.1Qaz enhanced transmission selection (ETS), and the data center bridging exchange (DCBX) protocol.
PAGE 446
To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.
PAGE 447
port-set port-pipe Command Modes Enter the keywords port-set and port-pipe number. The port-pipe number is 0. EXEC EXEC Privilege Command History Related Commands Version Description 9.10(0.0) Introduced on the C9010, S6000, S6000–ON, Z9100–ON and S6100–ON. pfc-nodrop-priority l2-dlf drop — configures to drop the unknown unicast packets flooding on lossless priorities. show hardware pfc-nodrop-priority — displays the packets drop count corresponding to the priority.
PAGE 448
pfc-nodrop-priority l2-dlf drop Configure to drop the unknown unicast packets flooding on lossless priorities. Syntax pfc-nodrop-priority l2-dlf drop To disable the feature, use the no pfc-nodrop-priority l2-dlf drop command. Parameters l2-dlf Enter the keywords l2-dlf to drop flooding traffic on lossless priorities. drop Enter the keyword drop to enable the drop action. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 449
Usage Information Version Description 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. • • When you configure lossless queues on an interface, PFC priority configuration is not allowed on the dcb-map profile applied on the interface. The maximum number of lossless queues globally supported on the switch is two. The following lists the dot1p priority-queue assignments.
PAGE 450
Usage Information Version Description 9.7(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. The default number of 802.1p priorities that you can enable for PFC is –2. The maximum number of 802.1p priorities that you can enable for PFC is –4. Queues to which PFC priority traffic is mapped are lossless by default.
PAGE 451
1 1 1 1 0.0 0.1 0.2 0.3 3399 3399 3399 3399 3088 3088 3088 3088 208 208 208 208 2880 2740 2880 2740 show hardware pfc-nodrop-priority View the packets drop count corresponding to the priority. Syntax Parameters Command Modes show hardware pfc-nodrop-priority l2-dlf drops stack-unit stack-unit-number port-set port-pipe stack-unit stackunit-number Enter the keywords stack-unit and the stack unit number. port-set port-pipe Enter the keywords port-set and port-pipe number. The port-pipe number is 0.
PAGE 452
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. Command Modes • For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 453
Field Description Operational status (local port) Port state for current operational PFC configuration: • Init: Local PFC configuration parameters were exchanged with the peer. • Recommend: Remote PFC configuration parameters were received from the peer. • Internally propagated: PFC configuration parameters were received from the configuration source. PFC DCBX Oper status Operational status for the exchange of the PFC configuration on the local port: match (up) or mismatch (down).
PAGE 454
-----------------------------------------------------------------------------------Te 1/1/3/1 Q0 NO Te 1/1/3/1 Q1 NO Te 1/1/3/1 Q2 NO Te 1/1/3/1 Q3 NO Te 1/1/3/1 Q4 NO Te 1/1/3/1 Q5 NO Te 1/1/3/1 Q6 NO Te 1/1/3/1 Q7 NO - show int hundredGigE 1/32 pfc detail Interface hundredGigE 1/32 Admin mode is on Admin is enabled Remote is disabled Local is enabled Oper status is init PFC DCBX Oper status is Down Reason: Port Shutdown State Machine Type is Symmetric TLV Tx Status is enabled PFC Link Delay 65535 pause
PAGE 455
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • For non-ON platforms, you can specify multiple ports as slot/port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 456
ETS Commands The following ETS commands are supported on the Dell Networking OS. NOTE: Before configuring ETS, assign the etsacl space. using the cam-acl l2acl 2 ipv4acl 0 ipv6acl 0 ipv4qos 2 l2qos 0 l2pt 0 ipmacacl 0 vman-qos 0 fcoeacl 2 etsacl 1 iscsi 2 command. dcb-enable Enable data center bridging. Syntax dcb enable[pfc-queues 1–4] To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command. The range is from 1 to 4.
PAGE 457
clear ets counters Clear all ETS TLV counters on an interface. Syntax Parameters clear ets counters port-type slot/port[/subport] port-type Enter the keywords port-type then the slot/port information. Enter the subport number if a 40G port is fanned-out into 10G ports. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.
PAGE 458
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 459
State Machine Type is Feature Conf TLV Tx Status is enabled Example (Detail) Dell(conf)#do show int te 1/1/1/1 ets detail Interface TenGigabitEthernet 1/1/1/1 Max Supported PG is 4 Number of Traffic Classes is 8 Admin mode is on Admin Parameters : -----------------Admin is enabled PG-grp Priority# BW-% BW-COMMITTED BW-PEAK TSA % Rate(Mbps) Burst(KB) Rate(Mbps) Burst(KB) ---------------------------------------------------------------------------------0 0,1,2,3,4,5,6,7 100 ETS 1 2 3 4 5 6 7 15 Remote Para
PAGE 460
• ets-conf: enables the advertisement of ETS configuration TLVs. • ets-reco: enables the advertisement of ETS recommend TLVs. • pfc: enables the advertisement of PFC TLVs. Defaults All PFC and ETS TLVs are advertised. Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.
PAGE 461
• auto-downstream: configures the port to accept the internally propagated DCB configuration from a configuration source. • manual: configures the port to operate only on administer-configured DCB parameters. The port does not accept a DCB configuration received form a peer or a local configuration source. Defaults Manual Command Modes INTERFACE PROTOCOL LLDP Command History This guide is platform-specific.
PAGE 462
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch.
PAGE 463
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. fcoe priority-bits Configure the FCoE priority advertised for the FCoE protocol in application priority TLVs. Syntax fcoe priority-bits priority-bitmap To remove the configured FCoE priority, use the no fcoe priority-bits command. Parameters priority-bitmap Enter the priority-bitmap range. The range is from 1 to FF.
PAGE 464
Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.
PAGE 465
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Down status messages added. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. To clear DCBX frame counters, use the clear dcbx counters interface stack-unit/port command. The following describes the show interface dcbx detail command shown in the following example.
PAGE 466
Example Field Description Peer DCBX Status: DCBX Operational Version DCBX version advertised in Control TLVs received from the peer device. Peer DCBX Status: DCBX Max Version Supported Highest DCBX version supported in Control TLVs received from the peer device. Peer DCBX Status: Sequence Number Sequence number transmitted in Control TLVs received from the peer device. Peer DCBX Status: Acknowledgment Number Acknowledgement number transmitted in Control TLVs received from the peer device.
PAGE 467
Acknowledgment Number: 2 Total DCBX Frames transmitted 27 Total DCBX Frames received 6 Total DCBX Frame errors 0 Total DCBX Frames unrecognized 0 dcb-map Create a DCB map to configure priority flow control (PFC) and enhanced transmission selection (ETS) on Ethernet ports that support converged Ethernet traffic. Apply the DCB map to an Ethernet interface. Syntax Parameters dcb-map map-nameTo remove a DCB map from an ethernet interface, use the no dcb-map command. map-name Enter a DCB map name.
PAGE 468
priority-pgid Assign 802.1p priority traffic to a priority group in a DCB map. Syntax priority-pgid dot1p0_group-num dot1p1_group-num dot1p2_group-num dot1p3_groupnum dot1p4_group-num dot1p5_group-num dot1p6_group-num dot1p7_group-num Parameters dot1p0–7_groupnum Enter the priority group number for each 802.1p class of traffic in a DCB map. Defaults None Command Modes DCB MAP Command History This guide is platform-specific.
PAGE 469
Parameters priority-group group-num Enter the keyword priority-group followed by the number of an 802.1p priority group. Use the priority-pgid command to create the priority groups in a DCB map. bandwidth percentage Enter the keyword bandwidth followed by a bandwidth percentage allocated to the priority group. The range of valid values is 1 to 100. The sum of all allocated bandwidth percentages in priority groups in a DCB map must be 100%.
PAGE 470
dcb-map stack-unit all stack-ports all Apply the specified DCB map on all ports of the switch stack. Syntax dcb-map stack-unit all stack-ports all dcb-map-name To remove the PFC and ETS settings in a DCB map from all stack units, use the no dcb-map stack-unit all stack-ports all command. Parameters dcb-map-name Enter the name of the DCB map. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 471
Usage Information Version Description 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms. Configure the maximum shared buffer available for PFC traffic. You can choose to increase or decrease the shared buffer that is allocated in the system by default. Configure the shared buffer size less than the total PFC buffer size.
PAGE 472
Example of commands in dcb buffer— threshold mode priority value buffer-size size pause-threshold threshold-value resume-offset threshold-value shared-threshold-weight size Dell(conf-dcb-buffer-thr)#priority 0 buffer-size 52 pause-threshold 16 resumeoffset 10 shared-threshold-weight 7 priority Configure the priority for the PFC threshold to be allocated to the buffer space parameters.
PAGE 473
Usage Information Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, and S6000 platforms. For each priority, you can specify the shared buffer threshold limit, the ingress buffer size, buffer limit for pausing the acceptance of packets, and the buffer offset limit for resuming the acceptance of received packets.
PAGE 474
the pause or resume thresholds for the buffer. This method of configuration enables you to effectively manage and administer the behavior of lossless queues. Example Dell(conf-if-te-1/1/1/1)# dcb-policy buffer-threshold test dcb pfc-total-buffer-size Configure the total buffer size for PFC in kilobytes. Syntax dcb pfc-total—buffer—size KB Parameters KB Enter a number in the range of 0 to 3399. Default The default is 3088KB.
PAGE 475
show running-config dcb-buffer-threshold Displays the DCB buffer threshold details in the running configuration. Syntax show running—config dcb-buffer-threshold Command Modes EXEC EXEC Privilege Command History Usage Information Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.
PAGE 476
Te 1/1/1/2 Te 1/1/1/2 Dell(conf)# Q6 Q7 NO NO - - - - On interface in which PFC is not enabled: Dell#show interface tengigabitethernet 1/1/1/1 pfc buffer-threshold The following table describes the output fields displayed for the show interface pfc buffer-threshold command: Field Description queue Number of the queue lossless Whether the queue is a lossy or lossless queue for which buffer threshold is configured buffer-size Ingress buffer size pause-thresholdvalue Buffer limit at which the
PAGE 477
dcb {ets | pfc} enable Enable priority flow control or enhanced transmission selection on interface. Syntax dcb {ets | pfc} enable • To disable ETS on interface, use “no dcb ets enable” command. • To disable PFC on interface, use “no dcb pfc enable” command. Defaults Enable Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 478
12 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell Networking OS. Topics: • Diagnostics and Monitoring Commands • Offline Diagnostic Commands • Hardware Commands Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack.
PAGE 479
Usage Information Version Description 8.3.7.0 Introduced on the S4810. The Kernel core dump can be large and may take up to 5 to 30 minutes to upload. Dell Networking OS does not overwrite application core dumps so you should delete them as necessary to conserve space on the flash; if the flash is out of memory, the coredump is aborted. Dell Networking OS completes the coredump process and wait until the upload is complete before rebooting the system.
PAGE 480
verbose Enter the keyword verbose to run the diagnostic in Verbose mode. Verbose mode gives more information in the output than Standard mode. no-reboot Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit stack-unitnumber command. interactive Enter the keyword interactive with the test ID to test interactive test cases.
PAGE 481
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series.
PAGE 482
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a unit which is already online. The system which is currently offline reboots when the online command is given. Hardware Commands These commands display information from a hardware sub-component or ASIC.
PAGE 483
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series.
PAGE 484
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. clear hardware vlan-counters Clear VLAN statistics. Syntax clear hardware vlan-couters vlan-id Parameters vlan-id Enter the interface VLAN number. The range is from 1 to 4094. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 485
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. This command enables a hardware watchdog mechanism that automatically reboots an Dell Networking OS switch/ router with a single unresponsive unit.
PAGE 486
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. The unit numbers given are internal port numbers. show hardware ip Display ACL or QoS data for the selected stack member and stack member port-pipe. Syntax show hardware layer3 {acl | qos} stack-unit number port-set 0–0 pipeline pipeline-number Parameters acl | qos Enter either the keyword acl or the keyword qos to select between ACL or QoS data.
PAGE 487
show hardware stack-unit Display the data plane or management plane input and output statistics of the designated component of the designated stack member.
PAGE 488
Example (DataPlane) 488 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Replaced the keyword port with interface. 9.7(0.0) Introduced on the S6000-ON. 9.2(0.2) Modified the drops keyword range, unit keyword range and added the buffer and cpu management statistics options. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.5 Added i2c statistics and sata-interfaces statistics. 8.3.11.
PAGE 489
txPkt(COS9 ) txPkt(COS10) txPkt(COS11) txPkt(UNIT0) :0 :0 :0 :0 Example (Party-Bus) Dell# show hardware stack-unit 1 cpu party-bus statistics Input Statistics: 0 packets, 0 bytes 0 dropped, 0 errors Output Statistics: 0 packets, 0 bytes 0 errors Example (Drops Unit) Dell#show hardware stack-unit 1 drops unit 0 Example (PortStats) Dell# show hardware stack-unit 1 ena/ speed/ link auto port link Lns duplex scan neg? ce0 up 4 100G FD SW No xe0 !ena 1 25G FD None No xe1 !ena 1 50G FD None No xe2 !ena 1 25G
PAGE 490
FA FA FA FA FA FA FA FA FA FA FA XGMII CR4 XGMII XGMII XGMII CR4 XGMII XGMII XGMII CR CR 9412 8996 9412 9412 9412 8996 9412 9412 9412 8996 8996 No No No No No No No No No No No Example (Register) Dell# show hardware stack-unit 1 unit 0 register 0x38804000 ASF_CREDIT_THRESH_HI.xe113 = 0x00000007 0x38804010 ASF_CREDIT_THRESH_HI.xe114 = 0x00000007 0x38804001 ASF_CREDIT_THRESH_HI.xe115 = 0x00000007 0x38804011 ASF_CREDIT_THRESH_HI.xe116 = 0x00000007 0x38804002 ASF_CREDIT_THRESH_HI.
PAGE 491
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter VLAN Tagged Packets Ingress Dropped Packet MTU Check Error Frame Counter PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame Priority 2 PFC Frame Priority 3 PFC Frame Priority 4 PFC Frame Priority 5 PFC Frame Priority 6 PFC Frame Priority 7 Deb
PAGE 492
Example (Details) ************************** bcmLinkMonStatusShow: The Current Link Status Is Front End Link Status 0x00000000 0x00000000 0x00000000 0x00000000 Front End Port Presence 0x00000000 0x00000000 0x00000000 0x00000000 Backplane Link Status 0x00000000 ****************************************************** Link Status of all the ports in the Device - 0 The The The The The The The The linkStatus linkStatus linkStatus linkStatus linkStatus linkStatus linkStatus linkStatus of of of of of of of of F
PAGE 493
• For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. all Display buffer statistics for all ports queue Enter the keyword queue followed by id for specific queue or keyword all. priority-group Identifier of the priority group in the range of 0 to 7.
PAGE 494
Example displaying total-buffer information for all interface in the specified stack member and unit Dell#show hardware stack-unit 0 buffer unit 0 interface all buffer-info Example displaying queue range Dell#show hardware stack-unit 0 buffer unit 0 interface all queue 6 buffer-info Buffer Stats for Front End Ports ================================ ----- Buffer Stats for Interface Te 1/1/1/1 Queue 6 ----Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: 8 Used Packet Buffer: 0 -----
PAGE 495
show hardware buffer-stats-snapshot Displays buffer statistics tracking resource information for a specific interface.
PAGE 496
multicast packets for --------------------------------------0 0 the specific interface UCAST UCAST 1 0 UCAST 2 0 UCAST 3 0 UCAST 4 0 UCAST 5 0 UCAST 6 0 UCAST 7 0 UCAST 8 0 UCAST 9 0 MCAST 0 0 MCAST 1 0 MCAST 2 0 MCAST 3 0 MCAST 4 0 MCAST 5 0 MCAST 6 0 MCAST 7 0 MCAST 8 0 MCAST 9 0 Example displaying egress queue-level snapshot for unicast packets for the specific interface Dell# show hardware buffer-stats-snapshot resource interface hundredGigE 1/10 queue ucast 0 Stack-unit 1 unit: 0 port: 34 (interface H
PAGE 497
MCAST MCAST MCAST Example displaying ingress prioritygroup level snapshot for the specific interface 7 8 9 0 0 0 Dell# show hardware buffer-stats-snapshot resource interface hundredGigE 1/10 prio-group 0 Stack-unit 1 unit: 0 port: 34 (interface Hu 1/10) --------------------------------------PG# SHARED CELLS HEADROOM CELLS --------------------------------------0 0 0 Dell# show hardware buffer-stats-snapshot resource interface hundredGigE 1/10 prio-group all Stack-unit 1 unit: 0 port: 34 (interface Hu 1/10
PAGE 498
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500.
PAGE 499
show hardware drops Displays internal drops on the specified interface or for a range of interface. Syntax Parameters Command Modes show hardware drops interface interface drops Enter the keyword drops to display internal drops. interface Enter any of the following keywords and the interface or interface range information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 500
Example displaying internal drops for all the interfaces 500 Version Description 9.2(0.2) Modified the drops keyword range, unit keyword range and added the buffer and cpu management statistics options. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.5 Added i2c statistics and sata-interfaces statistics. 8.3.11.4 Added user port information. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
PAGE 501
PKT Drops of ANY Conditions : 0 Hg MacUnderflow : 0 TX Err PKT Counter : 0 --- Error counters--Internal Mac Transmit Errors : 0 Unknown Opcodes : 0 Internal Mac Receive Errors : 0 --- FEC Counters --Ingress FEC uncorrected code words: 0 --- Error Ratio Counters --Ingress preFEC Bit Error Ratio: 0.0E0 Ingress FCS Drops Error Ratio : 0.
PAGE 502
--- Error Ratio Counters --Ingress preFEC Bit Error Ratio: 3.727463E-11 Ingress FCS Drops Error Ratio : 0.
PAGE 503
Ingress FCS Drops Error Ratio : 0.
PAGE 504
show hardware system-flow Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe. Syntax show hardware system-flow stack-unit id port-set number [counters | pipeline pipeline-number] Parameters stack-unit id Enter the keywords stack-unit to select a stack member ID. port-set number [counters | pipeline pipeline-number] Enter the keywords port-set with a port-pipe number. (OPTIONAL) Enter the keyword counters for the specified port-pipe.
PAGE 505
Part:0 Offset3: 84 Width3: 4 Part:0 Offset4: 88 Width4: 4 Part:0 Offset5: 92 Width5: 4 DATA=0x00000180 c2000000 MASK=0x0000ffff ffffffff InPorts Part:0 Offset0: 0 Width0: 36 DATA=0x00000001 ffffffff MASK=0x00000001 ffffffff HiGig Part:0 Offset0: 150 Width0: 2 DATA=0x00000000 MASK=0x00000001 action={act=DropPrecedence, param0=1(0x1), param1=0(0), param2=0(0), param3=0(0)} action={act=Drop, param0=0(0), param1=0(0), param2=0(0), param3=0(0)} action={act=CosQCpuNew, param0=7(0x7), param1=0(0), param2=0(0), par
PAGE 506
Related Commands • clear hardware system-flow — clear the statistics from selected hardware components. show hardware stack-unit buffer-stats-snapshot View the buffer statistics tracking resource information without polling details and historical snapshots.
PAGE 507
• Port- Priority-Group – Displays the shared space counters usage, head-room space counters per ingress port on per-priority- group granularity. When the buffer-stats-snapshot is disabled, an informational message is dispayed to this effect when you attempt to view the buffer statistics tracking resource information without polling details and historical snapshots. Example Only the queues for which the buffer cell consumption is not zero are displayed.
PAGE 508
Usage Information Version Description 9.3(0.0) Introduced on the S6000, S4810, and S4820T. The following information is displayed based on the buffer-info type, such as device-level details, queue-based snapshots, or priority group-level snapshot in the egress and ingress direction of traffic: • Device-ingress – Displays total buffer accounting usage for the unit. • Device-egress –Display total buffer usage for the unit, total multicast buffer usage for the unit and also on perservice-pool basis.
PAGE 509
13 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine.
PAGE 510
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Press Enter after the clear ip dhcp binding command clears all the IPs from the binding table.
PAGE 511
Version Description 8.2.1.0 Introduced on the C-Series and S-Series. debug ipv6 dhcp To enable debug logs for DHCPv6 relay agent transactions. Syntax debug ipv6 dhcp To disable the debug logs for dhcpv6 relay agent transactions, use the debug ipv6 dhcp command. Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 512
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. disable Disable the DHCP server. Syntax disable DHCP Server is disabled by default.
PAGE 513
Version Description 8.2.1.0 Introduced on the C-Series and S-Series. dns-server Assign a DNS server to clients based on address pool. Syntax Parameters dns-server address [address2...address8] address Enter a list of DNS servers that may service clients on the subnet. You may list up to eight servers, in order of preference. Defaults None Command Modes DHCP Command History This guide is platform-specific.
PAGE 514
Parameters name Give a name to the group of addresses in a pool. Defaults None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 515
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. hardware-address For manual configurations, specify the client hardware address.
PAGE 516
host For manual (rather than automatic) configurations, assign a host to a single-address pool. Syntax host address Parameters address/mask Enter the host IP address and subnet mask. Defaults None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 517
infinite Specify that the lease never expires. Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 518
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell Networking recommends specifying clients as hybrid.
PAGE 519
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. network Specify the range of addresses in an address pool. Syntax Parameters network network /prefix-length network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. Defaults None Command Modes DHCP Command History This guide is platform-specific.
PAGE 520
pool Create an address pool. Syntax pool name Parameters name Enter the address pool’s identifying name. Defaults None Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 521
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 522
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Dell# show ip dhcp configuration global Protocol status : Enabled Number of ping packets : 1 Dell# Dell# show ip dhcp configuration Pool Name Pool Type Domain Name Lease Time DNS Servers Default Routers Network : : : : : : : pool p1 p1 Dynamic dell.com 2Days 0Hrs 0Mins 10.11.0.1 1.1.1.1 1.1.1.0 255.255.255.
PAGE 523
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp server Display the DHCP server statistics. Syntax show ip dhcp server statistics Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON.
PAGE 524
Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks. arp inspection Enable dynamic arp inspection (DAI) on a VLAN. Syntax arp inspection Defaults Disabled Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 525
arp inspection-trust Specify a port as trusted so that ARP frames are not validated against the binding table. Syntax arp inspection-trust Defaults Disabled Command Modes Command History Related Commands • INTERFACE • INTERFACE PORT-CHANNEL This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 526
source-addressvalidation discardcounters Clears discard counters from all the interfaces configured with IP Source Guard. interface interface (OPTIONAL) Specifies an interface to clear the discard counters. Enter any of the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 527
The following example shows how to clear the discard counters on an interface: Dell> clear ip dhcp snooping source-address-validation discard-counters interface TenGigE 1/1/1/1 The following example shows how to clear the discard counters on a port channel interface: Dell> clear ip dhcp snooping source-address-validation discard-counters interface portchannel 1 Related Commands • show ip dhcp snooping — display the contents of the DHCP binding table.
PAGE 528
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(0.2) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 529
Usage Information Version Description 8.2.1.0 Introduced on the C-Series and S-Series on Layer 2 interfaces. 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces. When enabled, no learning takes place until you enable snooping on a VLAN. After disabling DHCP snooping, the binding table deletes and Option 82, IP Source Guard, and Dynamic ARP Inspection are disabled. Introduced in Dell Networking OS version 7.8.1.
PAGE 530
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp snooping binding Create a static entry in the DHCP binding table.
PAGE 531
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 532
Defaults • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. interface number Enter the number of the interface. lease value Enter the keyword lease then the amount of time the IPv6 address are leased. The range is from 1 to 4294967295. None Command Modes Command History • EXEC Privilege This guide is platform-specific.
PAGE 533
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. ipv6 dhcp snooping database write-delay To set time interval for storing the snooping binding entries in a file.
PAGE 534
Defaults None Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 535
ip dhcp snooping trust Configure an interface as trusted. Syntax [no] ip dhcp snooping trust Defaults Untrusted Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 536
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip dhcp source-address-validation Enable the IP Source Guard. Syntax [no] ip dhcp source-address-validation [ipmac] [vlan vlan-id] Parameters ipmac Enable IP+MAC Source Address Validation.
PAGE 537
Usage Information Version Description 7.8.1.0 Introduced on the C-Series and S-Series. Allocate at least one FP block to ipmacacl before you can enable IP+MAC Source Address Validation and SAV with VLAN option. 1 Use the cam-acl l2acl command from CONFIGURATION mode. 2 Save the running-config to the startup-config. 3 Reload the system. ip dhcp relay information-option Enable Option 82.
PAGE 538
Example Version Description 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series. Dell(conf)# ip dhcp relay information-option vpn ip dhcp snooping verify mac-address Validate a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Syntax [no] ip dhcp snooping verify mac-address Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 539
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series. ip helper-address Configures the destination broadcast address or the host address for DHCP server requests.
PAGE 540
ipv6 helper-address Configures the ipv6 DHCP helper addresses without VRF. Syntax [no] ipv6 helper-address ipv6-address To delete the ipv6 helper address, use the [no] ipv6 helper-address ipv6-address command. Parameters ipv6-address Enter the keywordipv6–address through which the server address can be reached. Default Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 541
Parameters Description discard-counters (OPTIONAL) Display the number of dropped packets. interface interface (OPTIONAL) Specifies an interface to show the discard counters. Enter any of the following keywords and the interface information: Defaults Command Modes Command History • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 542
Example The following example displays the interfaces configured with IP Source Guard: Dell> show ip dhcp snooping source-address-validation ip sav access-list on TenGigabitEthernet 1/1/1/1 Total cam count 3 permit host 0.0.0.0 count (0 packets) permit host 10.1.1.252 count (0 packets) permit host 10.1.1.253 count (0 packets) ipmac-vlan sav access-list on TenGigabitEthernet 1/1/1/2 Total cam count 4 permit host 0.0.0.0 host 00:00:00:00:00:00 count (0 packets) permit vlan 10 host 10.1.1.
PAGE 543
Total cam count 1 deny vlan 10 count (0 packets) deny access-list on Port-channel 10 on stack-unit 3 Total cam count 1 deny vlan 10 count (0 packets) NOTE: The output for port-channel interfaces does not display the physical interface. If the LAG member interfaces belong to different stack-units, the counters are displayed per stack-unit for that port channel. show ipv6 dhcp snooping Display the DHCPv6 snooping binding database.
PAGE 544
Commands to Configure DNS To configure the Domain Names Systems (DNS) on the system, use the following commands: ip name-server Configures one or more name server (DNS) IP addresses. You can configure up to six IP addresses. Syntax ip name-server [vrf vrf-name] ip-address [ip-address2] [ip-address3] [ipaddress4] [ip-address5] [ip-address6] To undo the name server ip address configuration for VRF, use the no ip name-server [vrf vrf-name] ip-address command.
PAGE 545
Example • Dell(conf)#ip name-server vrf jay 2.2.2.2 • Dell(conf)#ip name-server vrf jay 2.2.2.2 3.3.3.3 4.4.4.4 5.5.5.5 6.6.6.6 7.7.7.7 ip domain-name Configures the default domain corresponding to a specific VRF. This domain is appended to the in complete DNS requests corresponding to the specified VRF. Syntax ip domain-name [vrf vrf-name] name To undo the domain name configuration corresponding to a specific VRF, use the no ip domain-name [vrf vrf-name] name command.
PAGE 546
ip domain-list Adds a domain name to the DNS list. This domain name is appended to incomplete host names in DNS requests corresponding to a specific VRF. Syntax ip domain-list [vrf vrf-name] name To remove a domain name from DNS list, use the no ip domain-list [vrf vrf-name] name command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to add a domain name to the DNS list corresponding to that VRF.
PAGE 547
To undo the host name server to IP address mapping for VRFs, use the no ip host [vrf vrf-name] name ip-address command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the name server to IP address mapping for that VRF. name Enter the name od the host to be associated with an IP address. ip-address Enter the IP address of the name server in dotted decimal format.
PAGE 548
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 549
14 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. Topics: • ecmp-group • hash-algorithm • ip ecmp-group • ip ecmp weighted • link-bundle-distribution trigger-threshold • link-bundle-monitor enable ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle.
PAGE 550
Defaults Off Command Modes Command History Usage Information • CONFIGURATION • CONFIGURATION ECMP-GROUP This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 551
crc32MSB | crc32LSB | crcupper | dest-ip | flow-based-hashing | crc16|crc16cc| crc32MSB| crc32LSB|xor1 | xor2 | xor4 | xor8 | xor16}|lsb | xor1 | xor2 | xor4 | xor8 | xor16 hg {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} lag {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} • crc32MSB: Use CRC32_UPPER — MSB 16 bits of computed CRC32 • crc32LSB: Use CRC32_LOWER — LSB 16 bits of computed CRC32 • crc-upper: Uses the upper 32 bits of the key for t
PAGE 552
• xor16: Use CR16 — 16 bit XOR hg-seed seed-value (This option is available in stack-unit and linecard provisioned devices): Enter the keywords hg-seed then the hash algorithm seed value. The range is from 0 to 2147483646. stack-unit number (OPTIONAL) : Enter the keyword stack-unit then the stack-unit slot number. linecard number (OPTIONAL) : Enter the keyword linecard then the linecard slot number. port-set number (OPTIONAL) Enter the keyword port-set then the port-set slot number.
PAGE 553
• % Error: This command is not supported in the current microcode configuration In addition, the linecard number ip-sa-mask value ip-da-mask value option has the following behavior to maintain bi-directionality: • When hashing is done on both IPSA and IPDA, the ip-sa-mask and ip-da-mask values must be equal. (Single Linecard).
PAGE 554
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. You must save the new ECMP settings to the startup-config (write-mem) then reload the system for the new settings to take effect. ip ecmp weighted Enables weighted ECMP calculations. Syntax ip ecmp weighted To disable weighted ECMP calculations, enter the no ip ecmp weighted command.
PAGE 555
link-bundle-distribution trigger-threshold Provides a mechanism to set the threshold to trigger when traffic distribution begins being monitored on an ECMP link bundle. Syntax link-bundle-distribution trigger-threshold [percent] To exit from ecmp group mode, use the exit command. Parameters percent Indicate the threshold value when traffic distribution starts being monitored on an ECMP link bundle. The range is from 1 to 90%. The default is 60%.
PAGE 556
• Command History 556 PORT-CHANNEL INTERFACE This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 557
15 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. Topics: • load-balance ingress-port enable • load-balance flexhash • reload-type fastboot • lacp fast-switchover • encapsulation dot1q load-balance ingress-port enable Enable the Flex hash functionality. This utility is supported on the platform. Syntax load-balance ingress-port enable To disable the Flex hash capability, use the no version of this command.
PAGE 558
load-balance flexhash Specify the parameters for the Flex Hash mechanism, such as whether IPv4 or IPv6 packets must be subject to Flex Hash functionality, a unique protocol number, the offset of hash fields from the start of the L4 header to be used for hash calculation, and a meaningful description to associate the protocol number with the name.
PAGE 559
packet search key and matches packets based on the search key. When a packet matches the search key, two 16bit hash fields are extracted from the start of the L4 header and provided as inputs (bins 2 and 3) for RTAG7 hash computation. You must specify the offset of hash fields from the start of the L4 header, which contains a flow identification field.
PAGE 560
lacp fast-switchover Cause the physical ports to be aggregated faster by configuring this capability in a port-channel on both the nodes that are members of a port-channel. Syntax lacp fast-switchover To disable the capability of faster aggregation of the member ports of a LAG or a port-channel bundle, use the no version of this command. Defaults Not configured Command Modes INTERFACE (conf-if-po-number) Command History Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON.
PAGE 561
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.3.0.0 Introduced on the S6000. 9.2(1.0) Introduced on the Z9500. To enable routing of RRoCE packets, the VLAN ID is mapped to the default VLAN ID of 4095 and this mapping is performed using VLAN translation. After VLAN translation, the RRoCE packets are considered in the same manner as normal IP packets that received on L3 interface and routed in the egress direction.
PAGE 562
16 FIP Snooping In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibre Channel over Ethernet (FCoE) forwarders (FCFs). Acting as a transit FIP snooping bridge, the switch uses dynamically created access control lists (ACLs) to permit only authorized FCoE traffic to transmit between an FCoE end-device and an FCF.
PAGE 563
clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface. Syntax Parameters clear fip-snooping statistics [interface vlan vlan-id | interface port-type slot/port[/subport] | interface port-channel port-channel-number] vlan-id Enter the VLAN ID of the FIP packet statistics to be cleared. port-type slot/port Enter the slot number and port-type of the FIP packet statistics to be cleared.
PAGE 564
ipc Enter the keyword ipc for IPC-specific debugging. ns Enter the keyword ns for name-server-specific debugging. rscn Enter the keyword rscn for RSCN-specific debugging. rx Enter the keyword rx for packet receive-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 565
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 566
Usage Information Version Description 9.7(0.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Before enabling FIP snooping, assign the fcoeacl space using the cam-acl command. If not assigned, the following error message is displayed: Dell(conf)#feature fip-snooping % Error: Cannot enable fip snooping. CAM Region not allocated for Fcoe.
PAGE 567
fip-snooping fc-map Configure the FC-MAP value FIP snooping uses on all VLANs. Syntax fip-snooping fc-map fc-map-value To return the configured FM-MAP value to the default value, use the no fip-snooping fc-map command. Parameters Defaults Command Modes Command History fc-map-value Enter the FC-MAP value FIP snooping uses. The range is from 0EFC00 to 0EFCFF. 0x0EFC00 • CONFIGURATION • VLAN INTERFACE This guide is platform-specific.
PAGE 568
Defaults 32 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 9.2(0.2) Introduced on the S4810 and S4820T. fip-snooping port-mode fcf Configure the port for bridge-to-FCF links.
PAGE 569
fip-snooping port-mode fcoe-trusted Configure the port for bridge-to-bridge links. It is not recommended to use this command because multi-hop FSB is not supported. Syntax fip-snooping port-mode fcoe-trusted To remove the bridge-to-bridge link configuration from the port, use the no fip-snooping port-mode fcoe-trusted command. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 570
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 571
Usage Information Example The following describes the show fip-snooping enode command shown in the following example. Field Description ENode MAC MAC address of the ENode. ENode Interface Slot/ port number of the interface connected to the ENode. FCF MAC MAC address of the FCF. VLAN VLAN ID number the session uses. FC-ID Fibre Channel session ID the FCF assigns.
PAGE 572
Example Field Description FCF Interface Slot/port number of the interface to which the FCF is connected. VLAN VLAN ID number the session uses. FC-MAP FC-Map value the FCF advertises. ENode Interface Slot/ number of the interface connected to the ENode. FKA_ADV_PERIOD Time (in milliseconds) during which FIP keep-alive advertisements transmit. No of ENodes Number of ENodes connected to the FCF. FC-ID Fibre Channel session ID the FCF assigns.
PAGE 573
Field Description Number of VLAN Requests Number of FIP-snoop VLAN request frames received on the interface. Number of VLAN Notifications Number of FIP-snoop VLAN notification frames received on the interface. Number of Multicast Discovery Solicits Number of FIP-snoop multicast discovery solicit frames received on the interface. Number of Unicast Discovery Solicits Number of FIP-snoop unicast discovery solicit frames received on the interface.
PAGE 574
Example Dell# show fip-snooping statistics interface vlan 100 Number of Vlan Requests :0 Number of Vlan Notifications :0 Number of Multicast Discovery Solicits :2 Number of Unicast Discovery Solicits :0 Number of FLOGI :2 Number of FDISC :16 Number of FLOGO :0 Number of Enode Keep Alive :9021 Number of VN Port Keep Alive :3349 Number of Multicast Discovery Advertisement :4437 Number of Unicast Discovery Advertisement :2 Number of FLOGI Accepts :2 Number of FLOGI Rejects :0 Number of FDISC Accepts :16 Numbe
PAGE 575
Number of VN Port Session Timeouts :0 Number of Session failures due to Hardware Config :0 show fip-snooping system Display information on the status of FIP snooping on the switch (enabled or disabled), including the number of FCoE VLANs, FCFs, ENodes, and currently active sessions. Syntax Command Modes Command History Example show fip-snooping system • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 576
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the Z9500 and S6000-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 577
17 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember • FRRP is media- and speed-independent.
PAGE 578
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 579
debug frrp Clear the FRRP statistics counters. Syntax debug frrp {event | packet | detail} [ring-id] [count number] To disable debugging, use the no debug frrp {event | packet | detail} {ring-id} [countnumber] command. Parameters event Enter the keyword event to display debug information related to ring protocol transitions. packet Enter the keyword packet to display brief debug information related to control packets.
PAGE 580
description Enter an identifying description of the ring. Syntax description Word To remove the ring description, use the no description [Word] command. Parameters Word Enter a description of the ring. Maximum: 255 characters. Defaults None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 581
To enable the Resilient Ring Protocol, use the no disable command. Defaults Disabled Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 582
secondary interface control-vlan vlan-id • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a port channel interface, enter the keywords port-channel then a number. Enter the keyword secondary to configure the secondary interface then one of the following interfaces and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 583
member-vlan Specify the member VLAN identification numbers. Syntax member-vlan {vlan-range} To return to the default, use the no member-vlan [vlan-range] command. Parameters vlan-range Enter the member VLANs using VLAN IDs (separated by commas), a range of VLAN IDs (separated by a hyphen), a single VLAN ID, or a combination. For example: VLAN IDs (comma-separated): 3, 4, 6. Range (hyphen-separated): 5-10. Combination: 3, 4, 5-10, 8.
PAGE 584
To reset the mode, use the no mode {master | transit} command. Parameters master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Defaults Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 585
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 586
Usage Information Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings.
PAGE 587
2 Dell# Related Commands • Up Master 2 11-20, 25, 27-30 protocol frrp — enter the resilient ring protocol and designate a ring identification. timer Set the hello interval or dead interval for the Ring control packets. Syntax timer {hello-interval milliseconds}| {dead-interval milliseconds} To remove the timer, use the no timer {hello-interval [milliseconds]}| {dead-interval milliseconds} command.
PAGE 588
Usage Information 588 Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. The hello interval command is the interval at which ring frames are generated from the primary interface of the master node. The dead interval command is the time that elapses before a time-out occurs.
PAGE 589
18 GARP VLAN Registration (GVRP) The Dell Networking operating system supports the basic GVRP commands on the Dell Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 590
Topics: • clear gvrp statistics • debug gvrp • disable • garp timers • gvrp enable • gvrp registration • protocol gvrp • show config • show garp timers • show gvrp • show gvrp statistics clear gvrp statistics Clear GVRP statistics on an interface.
PAGE 591
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • show gvrp statistics — display the GVRP statistics. debug gvrp Enable debugging on GVRP.
PAGE 592
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 593
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • gvrp enable — enable GVRP on physical interfaces and LAGs. • protocol gvrp — access GVRP protocol. garp timers Set the intervals (in milliseconds) for sending GARP messages. Syntax garp timers {join | leave | leave-all} To return to the previous setting, use the no garp timers {join | leave | leave-all} command.
PAGE 594
Usage Information Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • Join Timer — Join messages announce the willingness to register some attributes with other participants.
PAGE 595
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • disable — globally disable GVRP. gvrp registration Configure the GVRP register type.
PAGE 596
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Fixed registration prevents an interface, configured using the command line, to belong to a VLAN (static configuration) from being unconfigured when it receives a Leave message. Therefore, Registration mode on that interface is fixed. Normal registration is the default registration.
PAGE 597
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series • disable — globally disable GVRP. show config Display the global GVRP configuration. Syntax show config Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 598
show garp timers Display the GARP timer settings for sending GARP messages. Syntax show garp timers Defaults None Command Modes Command History Example EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 599
show gvrp Display the GVRP configuration. Syntax Parameters Defaults Command Modes Command History show gvrp [brief | interface] brief (OPTIONAL) Enter the keyword brief to display a brief summary of the GVRP configuration. interface (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 600
Version Description 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Usage Information If no ports are GVRP participants, the message output changes from GVRP Participants running on to GVRP Participants running on no ports. Example Dell# show gvrp brief GVRP Feature is currently enabled.
PAGE 601
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000.
PAGE 602
19 ICMP Message Types This section lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. Table 1. ICMP messages and their definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 603
Symbol Type & 11 Code Description Query Error time exceeded: 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 604
20 Internet Group Management Protocol (IGMP) The IGMP commands are supported on the Dell Networking OS. Topics: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember • Dell Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent source-specific multicast (PIM-SSM) include and exclude modes. • IGMPv2 is the default version of IGMP on interfaces.
PAGE 605
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 606
• Parameters To disable all debugging, use the undebug all command. vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging of IGMP packets corresponding to that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 607
Usage Information IGMP commands accept only non-VLAN interfaces — specifying VLAN does not yield results. This command displays packets for IGMP and IGMP snooping. ip igmp access-group To specify access control for packets, use this feature. Syntax ip igmp access-group access-list To remove the feature, use the no ip igmp access-group access-list command. Parameters access-list Enter the name of the extended ACL (16 characters maximum).
PAGE 608
ip igmp immediate-leave Enable IGMP immediate leave. Syntax ip igmp immediate-leave [group-list prefix-list-name] To disable ip igmp immediate leave, use the no ip igmp immediate-leave command. Parameters group-list prefix-listname Enter the keywords group-list then a string up to 16 characters long of the prefix-listname. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 609
ip igmp last-member-query-interval Change the last member query interval, which is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages. This interval is also the interval between Group-Specific Query messages. Syntax ip igmp last-member-query-interval milliseconds To return to the default value, use the no ip igmp last-member-query-interval command. Parameters milliseconds Enter the number of milliseconds as the interval.
PAGE 610
ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 611
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 612
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 613
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax Parameters ip igmp version {2 | 3} 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. Defaults 2 (IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 614
show ip igmp groups View the IGMP groups. Syntax show ip igmp [vrf vrf-name] groups [group-address [detail] | detail | interface [group-address [detail]]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only.
PAGE 615
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series and C-Series. 7.5.1.0 Expanded to support the detail option. E-Series legacy command. Usage Information This command displays the IGMP database, including configured entries for either all groups on all interfaces, all groups on specific interfaces, or specific groups on specific interfaces.
PAGE 616
225.0.0.4 Example (Details) Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 Dell# show ip igmp group details Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.5 00:01:22 show ip igmp interface View information on the interfaces participating in IGMP.
PAGE 617
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 618
IGMP querying router is 50.10.4.1 (this system) IGMP version is 3 Vlan 4007 Inbound IGMP access group is not set Internet address is 50.30.124.4/24 IGMP is up on the interface IGMP query interval is 60 seconds IGMP querier timeout is 83 seconds IGMP max query response time is 10 seconds IGMP last member query response interval is 1000 ms IGMP immediate-leave is disabled IGMP activity: 0 joins IGMP querying router is 50.30.124.
PAGE 619
Example Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. Dell# show ip igmp ssm-map Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.
PAGE 620
• When enabled, IGMP snooping Querier periodically sends general queries with an IP source address of the VLAN interface. If it receives a general query on any of its VLAN member, it checks the IP source address of the incoming frame. If the IP SA in the incoming IGMP general query frame is lower than the IP address of the VLAN interface, the switch disables its IGMP snooping Querier functionality.
PAGE 621
debug ip igmp snooping Enable debugging of IGMP snooping packets on interfaces and groups. Syntax Parameters debug ip igmp snooping [group address | interface] • To disable debugging of IGMP snooping, use the no debug ip igmp snooping [group address | interface] command. • To disable all debugging, use the undebug all command. snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format.
PAGE 622
ip igmp snooping enable Enable IGMP snooping on all or a single VLAN. This command is the master on/off switch to enable IGMP snooping. Syntax ip igmp snooping enable To disable IGMP snooping, use the no ip igmp snooping enable command. Defaults Disabled. Command Modes Command History Usage Information • CONFIGURATION • INTERFACE VLAN This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 623
ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 624
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to Group-Leave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
PAGE 625
ip igmp snooping mrouter Statically configure a VLAN member port as a multicast router interface. Syntax ip igmp snooping mrouter interface interface To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 626
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information The Dell Networking OS provides the capability of statically configuring the interface to which a multicast router is attached. To configure a static connection to the multicast router, enter the ip igmp snooping mrouter interface command in the VLAN context. The interface to the router must be a part of the VLAN where you are entering the command.
PAGE 627
Version Description E-Series legacy command Usage Information This command enables the IGMP switch to send General Queries periodically. This behavior is useful when there is no multicast router present in the VLAN because the multicast traffic is not routed. Assign an IP address to the VLAN interface for the switch to act as a querier for this VLAN. show ip igmp snooping groups Display snooping related information for all the IGMP groups, interface or one group of one interface.
PAGE 628
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, Z9000, and Z9500. This command displays the IGMP database, including configured entries for either all groups on all interfaces, all groups on specific interfaces, or specific groups on specific interfaces.
PAGE 629
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command.
PAGE 630
21 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Topics: • Basic Interface Commands • Port Channel Commands • Enhanced Validation of Interface Ranges • ip http source-interface Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces.
PAGE 631
• For a tunnel interface, enter the keyword tunnel. The range is from 1 to 16383. NOTE: This command also enables you to clear the port configurations corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 632
Example Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4093 VLANs on the E-Series. Prior to the release, 2094 was supported. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Updated the definition of the learning-limit option for clarity.
PAGE 633
Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 634
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 635
Parameters desc_text Enter a text string up to 240 characters long. Defaults None Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 636
range • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the slot/port/subport information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the slot/ port/subport information.
PAGE 637
Related Commands • show running-config – display the current configuration. fec default Set the FEC to default value. Syntax fec default Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 638
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. This command is not applicable for 10–Gigabit and 40–Gigabit Ethernet interfaces. For 100-Gigabit Ethernet interfaces, CR4 auto-negotiation is enabled by default. You cannot enable or disable FEC separately.
PAGE 639
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.11(0.0) Added support for monitor session. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 640
• Speeds less than one Gig cannot be configured when the asymmetric flow control configuration is on. The following error is returned: Can’t configure speed <1G when Asymmetric flowcontrol is on, config ignored • Dell Networking OS only supports rx on tx on and rx off tx off for speeds less than one Gig (Symmetric). NOTE: If you use the disable rx flow control command, Dell Networking recommends rebooting the system.
PAGE 641
on on off off on on off off on on on off off on on on off off on on interface Configure a physical or virtual interface on the switch. Syntax Parameters interface interface interface Enter one of the following keywords and the interface information: • For a null interface, enter the keyword null then the slot/port information. The Null interface number is 0. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information.
PAGE 642
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added the support for interfaces. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 643
interface group Create or delete group of VLANs with a single command. You can also use this command to apply a set of configurations on a group of interfaces. Syntax interface group [interface | vlan vlanid {- vlanid } ] To delete a range of VLANs, use the following command: no interface group vlan vlanid {- vlanid} Parameters interface, interface,... Enter the keywords interface group and one of the interfaces — slot/port or VLAN number. Select the range of interfaces for bulk configuration.
PAGE 644
Usage Information Version Description 9.4(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL Switch. The interface group command will create all the non-existent VLANs specified in the range. On successful command execution, the CLI switches to the interface group context. The configuration commands inside the group context will be the similar to that of the existing range command. Note: For release 9.4(0.0), the group command is supported only for VLANs and physical interfaces.
PAGE 645
Example Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced Dell(conf)# interface loopback 1655 Dell(conf-if-lo-1655)# • interface — configure a physical interface. • interface null — configure a Null interface. • interface port-channel — configure a port channel. • interface vlan — configure a VLAN. interface managementEthernet Configure the Management port on the system (either the Primary or Standby RPM).
PAGE 646
The Management port is enabled by default (no shutdown). To assign an IP address to the Management port, use the ip address command. Example Dell(conf)# interface managementethernet 1/1 Dell(conf-if-ma-1/1)# Related Commands • management route — configure a static route that points to the Management interface or a forwarding router. • speed (Management interface) — Set the speed for the Management interface. interface null Configure a Null interface on the switch.
PAGE 647
Example Related Commands Dell(conf)# interface null 0 Dell(conf-if-nu-0)# • interface — configure a physical interface. • interface loopback — configure a Loopback interface. • interface port-channel — configure a port channel. • interface vlan — configure a VLAN. • ip unreachables — enable generation of internet control message protocol (ICMP) unreachable messages.
PAGE 648
Usage Information Version Description 9.8(0.0P5) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.2.1.0 Added support for 4093 VLANs on E-Series. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series. 7.6.1.
PAGE 649
Example (Overlapping Ports) Dell(conf)# interface range tengigabitethernet 1/1/1/1 - 1/1/3/1, tengigabitethernet 1/1/1/1 - 1/1/4/3 Dell(conf-if-range-te-1/1/1/1-1/1/4/3)# Usage Information Only VLAN and port-channel interfaces created using the interface vlan and interface port-channel commands can be used in the interface range command. Use the show running-config command to display the VLAN and port-channel interfaces.
PAGE 650
Spaces are not required between the commas. Comma-separated ranges can include VLANs, port-channels, and physical interfaces. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information.
PAGE 651
Dell# show running-config | grep define define interface-range test tengigabitethernet 1/1/1/1 - 1/1/3/1, tengigabitethernet 1/1/5/1 - 1/1/7/4, tengigabitethernet 1/1/8/1 - 1/1/8/4 Dell(config)# interface range macro test Dell(config-if-range-te-1/1/1/1-1/1/3/1,te-1/1/5/1-1/1/7/4,te-1/1/8/1-1/1/8/4)# Dell(config)# define interface-range test HundredGigE 1/1 - 1/3, HundredGigE 1/7 - 1/17, HundredGigE 1/19 - 1/22 Dell# show running-config | grep define define interface-range test HundredGigE 1/1 - 1/3, Hundre
PAGE 652
Example (Single Range) Version Description 6.2.1.0 Introduced This example shows the macro named test that was defined earlier. Dell(config)# interface range macro test Dell(config-if-range-te-1/1/1/1-1/1/1/3,te-1/1/3/1-1/1/4/4,te-1/1/7/1-1/1/9/1)# Dell Related Commands • interface range — configure a range of command (bulk configuration). • interface range macro (define) — define a macro for an interface range (bulk configuration). interface vlan Configure a VLAN.
PAGE 653
FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs and IP ACLs are supported. For more information, see Access Control Lists (ACL). The following features are not supported on VLANs associated with an OpenFlow instance: • IPv4 • IPv6 • MTU If OpenFlow VLANs are configured on the switch, spanning-tree protocols cannot be enabled simultaneously. Example (Single Range) Related Commands Dell(conf)# int vlan 3 Dell(conf-if-vl-3)# • interface — configure a physical interface.
PAGE 654
Usage Information Version Description 8.3.16.1 Introduced on the MXL 10/40GbE Switch IO Module. You can configure the interface type as CR4 with auto-negotiation enabled. If a DAC cable link is down, you can resolve the issue by setting the interface type as CR4. If the CR4 optic fails to come up, use the autoneg option. On 100-Gigabit Ethernet interfaces, CR4 auto-negotiation is enabled by default. Related Commands • Interfaces — configure a physical interface.
PAGE 655
Usage Information When you configure keepalive, the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive, the system does not send keepalive packets and so the local end of a WAN link remains up even if the remote end is down. monitor interface Monitor counters on a single interface or all interfaces. The screen is refreshed every five seconds and the CLI prompt disappears.
PAGE 656
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. In the Example, the delta column displays changes since the last screen refresh. The following are the monitor command menu options.
PAGE 657
Input overrun: Output underruns: Output throttles: m l T q Example (All Interfaces) - 0 0 0 0 pps 0 pps 0 pps Change mode Page up Increase refresh interval Quit 0 0 0 c - Clear screen a - Page down t - Decrease refresh interval systest-3 Monitor time: 00:01:31 Refresh Intvl.
PAGE 658
Usage Information Version Description 9.10(0.0) Reduced the maximum size of the maximum transmission unit (MTU) to 9216 bytes on S6000, S6000-ON, S4048-ON, Z9500, and C9010. Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000.
PAGE 659
Layer 2 Overhead Link MTU and IP MTU Delta Untagged Packet with VLAN-Stack Header 22 bytes Tagged Packet with VLAN-Stack Header 26 bytes negotiation auto Enable auto-negotiation on an interface. Syntax negotiation auto To disable auto-negotiation, use the no negotiation auto command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 660
You can use the negotiation auto command on the 10G ports on the device. The no negotiation auto command is only available if you first manually set the speed of a port to 10Mbits or 100Mbits. The negotiation auto command provides a mode option for configuring an individual port to forced-master/ forced slave after you enable auto-negotiation. If you do not use the mode option, the default setting is slave.
PAGE 661
• auto-negotiation enabled speed 100 • auto-negotiation disabled speed 100 • auto-negotiation disabled speed 100 • auto-negotiation enabled* speed 1000 or auto Port 1 • auto-negotiation enabled* speed 1000 or auto • auto-negotiation enabled speed 100 • auto-negotiation disabled speed 100 • auto-negotiation enabled speed 100 • auto-negotiation disabled speed 100 Link Status Between Port 1 and Port 2 • Up at 1000 Mb/s • Up at 100 Mb/s • Up at 100 Mb/s • Down • Down * You cannot dis
PAGE 662
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. The following describes the interface command shown in the following example. This example sets a port as hybrid, makes the port a tagged member of VLAN 20, and an untagged member of VLAN 10, which becomes the native VLAN of the port.
PAGE 663
Parameters seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds. NOTE: Because polling occurs every 15 seconds, the number of seconds designated here rounds to the multiple of 15 seconds lower than the entered value. For example, if 44 seconds is designated, it rounds to 30; 45 to 59 seconds rounds to 45. Defaults 299 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 664
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 665
show config (from INTERFACE RANGE mode) Display the bulk configured interfaces (interface range). Syntax show config Command Modes CONFIGURATION INTERFACE (conf-if-range) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 666
Parameters interface Enter one of the following keywords and the interface information: • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For stack-units, enter the keywords stack-unit then the slot/port information. • For a Null interface, enter the keyword null then the Null interface number. • For a port channel interface, enter the keywords port-channel then a number.
PAGE 667
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.2(0.2) Added support for the tunnel interface type. 9.1(0.0) Updated Management Ethernet output to include two global IPv6 addresses on S4810 and Z9000 and added output example showing OpenFlow instance ID. 8.3.12.1 Updated command output to support multiple IPv6 addresses on S4810. 8.3.11.4 Output expanded to support eSR4 optics in Z9000. 8.3.11.1 Introduced on the Z9000. 8.5.1.
PAGE 668
Line Description Internet address... States whether an IP address is assigned to the interface. If an IP address is assigned, that address is displayed. MTU 1554... Displays link and IP MTU information. LineSpeed Displays the interface’s line speed, duplex mode, and negotiation mode. Energy Efficient Ethernet Displays whether Energy Efficient Ethernet has been enabled or not. ARP type:... Displays the ARP type and the ARP timeout value for the interface. Last clearing...
PAGE 669
Line Description • wred=count both packets discarded in the MAC and in the hardware-based queues Rate information... Estimate of the input and output traffic rate over a designated interval (30 to 299 seconds). Traffic rate is displayed in bits, packets per second, and percent of line rate. Time since... Elapsed time since the last interface status change (hh:mm:ss format).
PAGE 670
32992398774 packets, 2243483116632 bytes 0 64-byte pkts, 32992398774 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 32992398774 Unicasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded 669 FEC bit errors, 172 FEC uncorrected code words Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0
PAGE 671
Virtual-IP IPv6 address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example (OpenFlow instance) Dell# show interfaces vlan 6 Vlan 6 is down, line protoc
PAGE 672
Command History Example 672 This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 673
show interfaces dampening Display interface dampening information. Syntax Parameters show interfaces dampening [[interface] [summary] [detail]] interface (Optional) Enter one of the following keywords and the interface information: • For a port channel interface, enter the keywords port-channel then a number. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 674
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 675
Example Related Commands Version Description 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 676
Syntax show interfaces [interface | stack—unit slot-number] status Parameters interface (OPTIONAL) Enter one of the following keywords the interface information: • For a port channel interface, enter the keywords port-channel then a number. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 677
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Example show interfaces vlan Display VLAN statistics.
PAGE 678
Usage Information NOTE: This command also enables you to view information corresponding to a range of ports. • Example You can specify multiple ports as port-range. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1 - 4.
PAGE 679
1/3 1/5 1/7 1/9 1/11 1/13 1/15 2/1 2/3 2/5 2/7 2/9 2/11 2/13 2/15 Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad Quad 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G 10G show interfaces switchport Display only virtual and physical interfaces in Layer 2 mode. This command displays the Layer 2 mode interfaces’ IEEE 802.1Q tag status and VLAN membership.
PAGE 680
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 681
Vlan 2 Name: TenGigabitEthernet 1/1/3/1 802.1QTagged: True Vlan membership: Vlan 2 Name: TenGigabitEthernet 1/1/4/1 802.1QTagged: True Vlan membership: Vlan 2 --More-Related Commands • interface — configure a physical interface on the switch. • show ip interface — display Layer 3 information about the interfaces. • show interfaces transceiver — display the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number.
PAGE 682
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(2.0) Introduced on the S3100 series. 9.8(1.
PAGE 683
Line Description TX Power High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power High Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+. Bias Low Alarm threshold Factory-defined setting. Value can differ between SFP and SFP+.
PAGE 684
Interfaces Line Description Tx Power Present Tx power of the SFP. If this crosses Tx power alarm/warning thresholds, the Tx power high alarm/warning flag is set to true. If it falls below the low alarm/warning thresholds, the Tx power low alarm/ warning flag is set to true. Rx Power Present receiving (Rx) power of the SFP. This value is either average Rx power or OMA. This depends on the Rx Power measurement type displayed above.
PAGE 685
Example Line Description Tx Power High Warning Flag This can be either true or false, depending on the Current Tx power value displayed above. Rx Power High Warning Flag This can be either true or false, depending on the Current Tx power value displayed above. Temperature Low Warning Flag This can be either true or false, depending on the Current Temperature value displayed above. Voltage Low Warning Flag This can be either true or false, depending on the Current Voltage value displayed above.
PAGE 686
QSFP 4/7/1 Bias High Warning threshold QSFP 4/7/1 RX Power High Warning threshold QSFP 4/7/1 Temp Low Warning threshold QSFP 4/7/1 Voltage Low Warning threshold QSFP 4/7/1 Bias Low Warning threshold QSFP 4/7/1 RX Power Low Warning threshold =================================== QSFP 4/7/1 Temperature QSFP 4/7/1 Voltage QSFP 4/7/1 TX1 Bias Current QSFP 4/7/1 TX2 Bias Current QSFP 4/7/1 TX3 Bias Current QSFP 4/7/1 TX4 Bias Current QSFP 4/7/1 RX1 Power QSFP 4/7/1 RX2 Power QSFP 4/7/1 RX3 Power QSFP 4/7/1 RX4 Pow
PAGE 687
Command History Example Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 688
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 689
Parameters 10 Enter the keyword 10 to set the interface’s speed to 10 Mb/s. NOTE: This interface speed is not supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. If the command is entered for these interfaces, an error message appears. 100 Enter the keyword 100 to set the interface’s speed to 10/100 Mb/s. NOTE: When this setting is enabled, only 100Base-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s.
PAGE 690
Usage Information This command is found on the 10/100/1000/10000 Base-T Ethernet interfaces. When you enable auto, the system performs an automatic discovery to determine the optics installed and configure the appropriate speed. When you configure a speed for the 10/100/1000/10000 interface, confirm the negotiation auto command setting. Both sides of the link must have auto-negotiation either enabled or disabled.
PAGE 691
Usage Information Related Commands Version Description 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. This command is found on the Management interface only. • interface ManagementEthernet — configure the Management port on the system (either the Primary or Standby RPM). • management route — configure a static route that points to the Management interface or a forwarding router.
PAGE 692
Usage Information Version Description 9.7(0.0) Added support for dynamically fanning-out of interfaces on S6000. Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. You can split a 100G port into two 50G, one 40G, four 10G, or four 25G ports.
PAGE 693
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 694
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface. To use the switchport command on an interface, only the no ip address and no shutdown statements must be listed in the show config output. When you enter the switchport command, the interface is automatically added to the default VLAN.
PAGE 695
Defaults Not configured. Command Modes INTERFACE PORTCHANNEL Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 696
• interface port-channel — create a Port Channel interface. • shutdown — disable/enable the port channel. group Group two LAGs in a supergroup (“fate-sharing group” or “failover group”). Syntax group group_number port-channel number port-channel number To remove an existing LAG supergroup, use the no group group_number command. Parameters group_number Enter an integer from 1 to 32 that uniquely identifies this LAG fate-sharing group.
PAGE 697
interface port-channel Create a Port Channel interface, which is a link aggregation group (LAG) containing 16 physical interfaces on the S-Series. Syntax interface port-channel channel-number To delete a Port Channel, use the no interface port-channel channel-number command. Parameters channel-number For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 4096. Defaults Not configured.
PAGE 698
If the line card is in a Jumbo mode chassis, you can also configure the mtu and ip mtu commands. The Link MTU and IP MTU values configured on the channel members must be greater than the Link MTU and IP MTU values configured on the Port Channel interface. If the stack—unit card is in a Jumbo mode chassis, you can also configure the mtu and ip mtu commands.
PAGE 699
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If you use this command to configure the minimum number of links in a LAG that must be in “oper up” status, the LAG must have at least that number of “oper up” links before it can be declared as up.
PAGE 700
other LAG. You can use both static and dynamic (LACP) LAGs to configure failover groups. For more information, see the “Port Channel” section in the Dell Networking OS Configuration Guide. Related Command • group — group two LAGs in a supergroup (“fate-sharing group”). • show interfaces port-channel — display information on configured Port Channel groups. show interfaces port-channel Display information on configured Port Channel groups.
PAGE 701
Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. Modified to display the LAG failover group status. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Example The following describes the show interfaces port-channel command shown in the following example. Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fate-sharing group (“Failover-group”) is listed. Hardware is...
PAGE 702
Members in this channel: Hu 2/5 Hu 2/18 ARP type: ARPA, ARP timeout 04:00:00 Last clearing of "show interfaces" counters 00:00:00 Queueing strategy: fifo 44507301 packets input, 3563070343 bytes Input 44506754 IP Packets, 0 Vlans 0 MPLS 41 64-byte pkts, 44502871 over 64-byte pkts, 249 over 127-byte pkts 407 over 255-byte pkts, 3127 over 511-byte pkts, 606 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 1218120 packets output, 10
PAGE 703
show port-channel-flow Display an egress port in a given port-channel flow. Syntax Parameters show port-channel-flow outgoing-port-channel number incoming-interface interface {source-ip address destination-ip address} | {source-port number destination-port number} | {source-mac address destination-mac address {vlan vlanid | ether-type}} outgoing-portchannel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information.
PAGE 704
Usage Information Version Description 9.10(0.0) Increased the number of port channels to 4096. Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810.
PAGE 705
ip http source-interface Specify an interface as the source interface for HTTP connections. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command. Parameters interface Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 706
22 IPv4 Routing The basic IPv4 commands are supported by Dell Networking OS on the platform.
PAGE 707
• load-balance hg • management route • show arp • show arp retries • show hosts • show ip cam stack-unit • show ip fib stack-unit • show ip flow • show ip interface • show ip management-route • show ipv6 management-route • show ip protocols • show ip route • show ip route list • show ip route summary • show ip traffic • show tcp statistics arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP).
PAGE 708
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 709
arp backoff-time Set the exponential timer for resending unresolved ARPs. Syntax Parameters arp backoff-time seconds seconds Enter the number of seconds an ARP entry is black-holed. The range is from 1 to 3600. The default is 30. Defaults 30 Command Mode CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.
PAGE 710
Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 711
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S4810 and S4820T.
PAGE 712
Usage Information Related Commands Version Description 8.3.1.0 Introduced. Retries are 20 seconds apart. • show arp retries — display the configured number of ARP retries. arp timeout Set the time interval for an ARP entry to remain in the ARP cache. Syntax arp timeout minutes Parameters minutes Enter the number of minutes. The range is from 0 to 35790. The default is 240 minutes. Defaults 240 minutes (4 hours) Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 713
Version Description pre-6.2.1.1 Introduced on the E-Series. clear arp-cache Clear the dynamic ARP entries from a specific interface or optionally delete (no-refresh) ARP entries from the content addressable memory (CAM). Syntax Parameters clear arp-cache [vrf vrf-name | interface | ip ip-address] [no-refresh] vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to clear the ARP cache corresponding to that VRF.
PAGE 714
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.
PAGE 715
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. clear ip fib stack-unit Clear all FIB entries in the specified stack unit (use this command with caution, refer to Usage Information.
PAGE 716
Related Commands • show ip fib stack-unit — show FIB entries on a specified stack-unit. clear ip route Clear one or all routes in the routing table. Syntax clear ip route [vrf vrf-name] {* | ip-address mask} Parameters vrf vrf-name (Optional) Enter the keyword vrf and then the name of the VRF to clear the routes corresponding to that VRF. * Enter an asterisk (*) to clear all learned IP routes.
PAGE 717
Usage Information Use the vrf vrf-name attribute of this command to clear routes corresponding to either a specific VRF or the default VRF. You cannot use this attribute to clear routes corresponding to a management VRF. Related Commands • ip route — assign an IP route to the switch. • show ip route — view the routing table. • show ip route summary — view a summary of the routing table. clear tcp statistics Clear TCP counters.
PAGE 718
debug arp View information on ARP transactions. Syntax debug arp [interface] [count value] To stop debugging ARP transactions, use the no debug arp command. Parameters interface count value (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 719
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series(the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Added the count option. To stop packets from flooding the user terminal when debugging is turned on, use the count option.
PAGE 720
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series. Dell# debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.17 BOOTP Request, hops = 0, XID = 0xbf05140f, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 0.0.0.0 00:12:21 : %RELAY-I-BOOTREQUEST: Forwarded BOOTREQUEST for 00:60:CF:20:7B:8C to 14.4.4.
PAGE 721
To disable debugging, use the no debug ip icmp command. Parameters interface count value (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 722
Example ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: Usage Information echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.40 echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.40 reply reply reply reply To stop packets from flooding the user terminal when debugging is turned on, use the count option.
PAGE 723
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Added the access-group option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.
PAGE 724
proto=89 IP: s=40.40.40.40 (local), d=224.0.0.6 (Te 1/1/4/1), len 28, sending broad/ multicast proto=2 IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable ICMP type=8, code=0 IP: s=0.0.0.0, d=30.30.30.30, len 100, unroutable ICMP type=8, code=0 Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option. The access-group option supports only the equal to (eq) operator in TCP ACL rules.
PAGE 725
secondary (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 726
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 727
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To configure a list of possible domain names, configure the ip domain-list command up to six times.
PAGE 728
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 729
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 730
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6. 8.
PAGE 731
Defaults Enabled; the hops field in the DHCP message header is incremented by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 732
ip address Enter an IP address, in dotted decimal format, to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 733
• For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 734
ipv6 icmp source-interface Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and reachability problems with IPv6 packets.
PAGE 735
Usage Information You can enable the mechanism to configure the source or the originating interface from which the packet (the device that generates the ICMP error messages) is received by the switch to send the loopback address instead of its source IP address to be used in the ICMP unreachable messages and in the traceroute command output. The loopback address must be unique in a particular domain.
PAGE 736
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced for the E-Series. To avoid denial of service (DOS) attacks, keep the number of fragments allowed for re-assembly low. ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use.
PAGE 737
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell Networking OS does not support sending DNS queries over a VLAN. DNS queries are sent out on all other interfaces, including the Management port. You can separately configure both IPv4 and IPv6 domain name servers.
PAGE 738
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. • show ip interface — display the interface routing status and configuration. ip route Assign a static route to the switch.
PAGE 739
• For a tunnel interface, enter the keyword tunnel then the tunnel interface number. The range is from 1 to 16383. If you configure a static IPv6 route using an egress interface and enter the ping command to reach the destination IPv6 address, the ping operation may not work. Configure the IPv6 route using a next-hop IPv6 address in order for the ping command to detect the destination address. interface ip-address Enter the keyword interface then the IP address.
PAGE 740
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Using the following example of a static route: ip route 33.33.33.0 /24 tengigabitethernet 1/1/1/1 172.31.5.
PAGE 741
ip source-route Enable Dell Networking OS to forward IP packets with source route information in the header. Syntax ip source-route To drop packets with source route information, use the no ip route-source command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 742
Parameters Command Modes Command History Usage Information <8-75> Wait duration in seconds for the TCP connection to be established. CONFIGURATION Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 743
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload. ipv4 unicast-host-route Enable programming of IPv4 /32 route prefixes in L3 host table.
PAGE 744
Command History Version Description 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages. Syntax ip unreachables To disable the generation of ICMP messages, use the no ip unreachables command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 745
load-balance By default, for C-Series and S-Series, Dell Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 746
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 747
port | L4-destport ] mac [source-mac | source-port-id | source-module-id | dest-mac | destport-id | destmodule-id | vlan | ethertype | sourcedest-mac ] tunnel [ipv4-overipv4 | ipv4-overgre-ipv4 | mac-inmac]} • dest-port-id — Use dest-port-id field in hash calculation. • dest-module-id — Use dest-module-id field in hash calculation. • protocol — Use IPv4 protocol field in hash calculation. • vlan — Use vlan field in hash calculation.
PAGE 748
management route Configure a static route that points to the Management interface or a forwarding router. Syntax management route {ip-address mask | ipv6-address 1.1.1.1prefix-length} {forwarding-router-address | managementethernet | fortyGigE | vlan | tengigabitethernet} To remove a static route, use the no management route command. Parameters ip-address mask Enter an IP address (dotted decimal format) and mask (/prefix format) of the destination subnet.
PAGE 749
Usage Information Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route.
PAGE 750
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. ip ip-address mask (OPTIONAL) Enter the keyword ip then an IP address in the dotted decimal format. Enter the optional IP address mask in the slash prefix format (/ x).
PAGE 751
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. The following example shows two VLANs that are associated with a private VLAN (PVLAN) (refer to Private VLAN (PVLAN)). If you have entered the clear arp-cache command to remove a large number of ARP entries and the command is still being processed in the background, an error message display if you attempt to enter the show arp command: Clear arp in-progress.
PAGE 752
Description Total Entries Lists the total number of ARP entries in the ARP table. Static Entries Lists the total number of configured or static ARP entries. Dynamic Entries Lists the total number of learned or dynamic ARP entries. CPU Lists which CPU the entries are stored on.
PAGE 753
Related Commands • arp retries — set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. show hosts View the host table and DNS configuration. Syntax Command Modes Command History Usage Information show hosts • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 754
Field Description Name servers are... Lists the name servers, if configured. Host Displays the host name assigned to the IP address. Flags Classifies the entry as one of the following: • perm — the entry was manually configured and will not time out • temp — the entry was learned and will time out after 72 hours of inactivity. Also included in the flag is an indication of the validity of the route: Example • ok — the entry is valid. • ex — the entry expired. • ?? — the entry is suspect.
PAGE 755
[ecmp-group detail]] • Enter the keyword longer-prefixes to view routes with a common prefix. • Enter the keyword ecmp-group detail to view the ECMP group index. ecmp-group {detail | member-info [detail [group-index index-number]]} (OPTIONAL) Enter the keyword ecmp-group then one of the following keywords to filter results. summary Command Modes Command History Usage Information • EXEC • EXEC Privilege • Enter the keyword detail to view the ECMP group index.
PAGE 756
Example Field Description Mac Addr Displays the next-hop router’s MAC address. Port Displays the egress interface. • CP = control processor • Gi = Gigabit Ethernet interface • Te = 10–Gigabit Ethernet interface Dell# show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port -------------------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Te 1/1/1/1 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP 1.1.1.
PAGE 757
Command Modes Command History Usage Information longer-prefixes (OPTIONAL) Enter the keywords longer-prefixes to view all routes with a common prefix. summary (OPTIONAL) Enter the keyword summary to view the total number of prefixes in the FIB. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 758
2.1.1.2/32 0.0.0.0/0 1.1.1.0/24 1.1.1.1/32 2.1.1.0/24 2.1.1.1/32 100.1.1.0/24 100.1.1.0/24 Dell# S Dell#show ip route 10.1.1.0/24 S S Example (Show command output with Weighted ECMP Enabled) Related Commands via 2.1.1.2, Vl 20 Direct, Vl 1000 via 127.0.0.1 Direct, Vl 20 via 127.0.0.1 via 1.1.1.2, Vl 1000 via 2.1.1.2, Vl 20 20.1.1.0/24 100.1.1.0/24 via via via via via 2.1.1.2 0.0.0.0 0.0.0.0 127.0.0.1 0.0.0.0 127.0.0.1 1.1.1.2 2.1.1.
PAGE 759
destination-port number Enter the keywords destination-port then the destination port number. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 760
show ip interface View IP-related information on all interfaces. Syntax show ip interface [interface | brief] [configured] Parameters interface (OPTIONAL) Enter the following keywords and the interface information: Command Modes Command History 760 IPv4 Routing • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 761
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 8.1.1.
PAGE 762
ICMP unreachables are not sent IP unicast RPF check is not supported Dell# Dell# show ip interface port-channel 128 Port-channel 128 is down, line protocol is down Internet address is 10.1.1.1/16 Broadcast address is 10.1.255.
PAGE 763
show ip management-route View the IP addresses assigned to the Management interface. Syntax Parameters Command Modes Command History Example show ip management-route [all | connected | summary | static] all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
PAGE 764
172.16.1.0/24 Dell# 10.1.2.4 Active show ipv6 management-route Display the IPv6 static routes configured for the management interface. Syntax show ipv6 management-route [all | connected | summary | static] Parameters all (OPTIONAL) Enter the keyword all to view all IP addresses assigned to all Management interfaces on the switch. connected (OPTIONAL) Enter the keyword connected to view only routes directly connected to the Management interface.
PAGE 765
show ip protocols View information on all routing protocols enabled and active on the switch. Syntax Command Modes Command History Example show ip protocols • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 766
Weight : 0 Address : 5::6 Weight : 0 Dell# show ip route View information, including how they were learned, about the IP routes on the switch. Syntax show ip route [vrf vrf-name] hostname | ip-address [mask] [longer-prefixes] | list prefix-list | protocol [process-id | routing-tag] | all | connected | static | summary] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the VRF name to list the routes in the route table of a specific VRF.
PAGE 767
• Command History Usage Information EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 768
Field Description • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + = summary routes The weight for weighted ECMP route calculations is displayed for each path in the route in show ip route command. The ECMP weight is displayed only if weighted ECMP is enabled using the ip ecmp weighted command is enabled. If weighted ECMP is disabled, the show ip route command does not show the weighted ECMP route information.
PAGE 769
Example (vrf) Dell# show ip route vrf test1 Codes: C - connected, S - static, R - RIP, B - BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated, O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set C Example (With Weighted ECMP E
PAGE 770
show ip route list Display IP routes in an IP prefix list. Syntax show ip route [vrf vrf-name] list prefix-list Parameters Command Modes Command History Example prefix-list Enter the name of a configured prefix list. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IP routes in an IP prefix list corresponding to that VRF. • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 771
L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.0/24 2.1.3.0/24 2.1.4.0/24 Gateway Dist/Metric Last Change ----------------- ----------via 2.1.4.1, Te 1/1/1/1 120/2 3d0h via 2.1.4.1, Te 1/1/1/1 120/2 3d1h via 2.1.4.1, Te 1/1/1/1 120/1 3d0h via 2.1.4.
PAGE 772
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example. Column Heading Description Example Route Source Identifies how the route is configured in Dell Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources.
PAGE 773
rp1 (OPTIONAL) Enter the keyword rp1 to view only the statistics from Route Processor 1. rp2 (OPTIONAL) Enter the keyword rp2 to view only the statistics from Route Processor 2. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 774
Keyword Definition ... couldn’t fragment Number of packets that could not be fragmented and forwarded. ...encapsulation failed Counts packets which could not be forwarded due to ARP resolution failure. Dell Networking OS sends an arp request prior to forwarding an IP packet. If a reply is not received, Dell Networking OS repeats the request three times. These packets are counted in encapsulation failed. Rcvd: ...short packets The number of bytes in the packet are too small. ...
PAGE 775
Sent: 21 requests, 10 replies (0 proxy) Routing Processor1 IP Traffic: show tcp statistics View information on TCP traffic through the switch. Syntax Parameters show tcp statistics {all | cp} all Enter the keyword all to view all TCP information. cp Enter the keyword cp to view only TCP information from the Control Processor. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 776
Field Description • Example too short 329 packets... Displays the number of packets and bytes received in sequence. 17 dup... Displays the number of duplicate packets and bytes received. 0 partially... Displays the number of partially duplicated packets and bytes received. 7 out-of-order... Displays the number of packets and bytes received out of order. 0 packets with data after window Displays the number of packets and bytes received that exceed the switch’s window size.
PAGE 777
Sent: 12007 Total, 0 urgent packets 25 control packets (including 24 retransmitted) 11603 data packets (12439677 bytes) 24 data packets (7638 bytes) retransmitted 355 ack only packets (41 delayed) 0 window probe packets, 0 window update packets 7 Connections initiated, 8 connections accepted, 15 connections established 14 Connections closed (including 0 dropped, 0 embryonic dropped) 20 Total rxmt timeout, 0 connections dropped in rxmt timeout 0 Keepalive timeout, 0 keepalive probe, 0 Connections dropped in
PAGE 778
23 IPv6 Basics IPv6 basic commands are supported on the Dell Networking OS. NOTE: For information about the Dell Networking OS version and platform that supports IPv6 in each software feature, see the IPv6 Addressing section in the Dell Networking OS Configuration Guide.
PAGE 779
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. You can partition the LPM table to store IPv6 prefixes greater than /64 mask length. Requires reboot of the switch to take effect as the SDK handles this only during its initialization. clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table.
PAGE 780
maximum dynamic-routes-ipv6 Specify the maximum number of dynamic (protocol) IPv6 routes a VRF can have. Syntax maximum dynamic-routes—ipv6 limit {warn-threshold threshold-value | warning-only} To remove the limit on the maximum number of IPv6 routes used, use the no maximum dynamic-routesipv6 command. Parameters limit Maximum number of IPv6 routes allowed in a VRF. Valid range is from 1 to 8000 (or maximum allowable for that platform if smaller value).
PAGE 781
show cam-ipv6 extended-prefix Display the current settings and next-boot settings for cam-ipv6 extended-prefix configuration. Display the cam-ipv6 extended-prefix configuration. Syntax show cam-ipv6 extended-prefix Defaults None Command Modes EXEC EXEC Privilege Command History Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000.
PAGE 782
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.1) Introduced on the S6000. Usage Information You can use this command to enable programming of /128 route prefixes in L3 host table or in LPM table. A warning message is displayed when you enter this command stating that this setting takes effect for existing routes only when IPv6 route prefixes are cleared from the routing table (RTM).
PAGE 783
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Introduced on the Z9000, S6000, S4810, S4820T, and MXL.. Usage Information Use this command to add, edit, or delete an IPv6 RDNSS address and lifetime value. You can configure up to four IPv6 RDNSS addresses. You must specify a lifetime using the lifetime or infinite parameter. Example Dell(conf-if-te-1/1/1/1)# ipv6 nd dns-server 1000::1 1 ipv6 route Establish a static IPv6 route.
PAGE 784
Configure the IPv6 route using a next-hop IPv6 address in order for the ping command to detect the destination address. ipv6-address (OPTIONAL) Enter the forwarding router IPv6 address in the x:x:x:x::x format. NOTE: The :: notation specifies successive hexadecimal fields of zeros. distance (OPTIONAL) Enter a number as the metric distance assigned to the route. The range is from 1 to 255. tag value (OPTIONAL) Enter the keyword tag then a tag value number. The range is from 1 to 4294967295.
PAGE 785
Usage Information When the interface goes down, Dell Networking OS withdraws the route. The route is re-installed, by Dell Networking OS, when the interface comes back up. When a recursive resolution is “broken,” Dell Networking OS withdraws the route. The route is re-installed, by Dell Networking OS, when the recursive resolution is satisfied.
PAGE 786
Defaults (OPTIONAL) View only the directly connected IPv6 routes. isis (OPTIONAL) View information for all IPv6 IS-IS routes. list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes. static (OPTIONAL) View only routes configured by the ipv6 route command. summary (OPTIONAL) View a brief list of the configured IPv6 routes.
PAGE 787
Field Example (S-Series) Description • O = OSPF • IA = OSPF inter-area • N1 = OSPF NSSA external type 1 • N2 = OSPF NSSA external type 2 • E1 = OSPF external type 1 • E2 = OSPF external type 2 • i = IS-IS • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + = summary routes Destination Identifies the route’s destination IPv6 address.
PAGE 788
24 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking OS. NOTE: For IPv4 ACL commands, see Access Control Lists (ACL). Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, see cam-acl. • Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. • Reference to an empty ACL permits any traffic.
PAGE 789
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810.
PAGE 790
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 791
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.
PAGE 792
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. ipv6 control-plane egress-filter Enable egress Layer 3 ACL lookup for IPv6 CPU traffic. Syntax ipv6 control-plane egress-filter Defaults Not enabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 793
ipv6 access-list Configure an access list based on IPv6 addresses or protocols. Syntax ipv6 access-list access-list-name cpu-qos To delete an access list, use the no ipv6 access-list access-list-name command. Parameters access-list-name Enter the access list name as a string, up to 140 characters. cpu-qos Enter the keyword cpu-qos to assign this ACL to control plane traffic only (CoPP). permit Enter the keyword permit to configure a filter to forward packets meeting this condition.
PAGE 794
Usage Information Version Description 7.4.1.0 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent. For detailed specification on entries allowed per ACL, refer to your line card documentation. You can create an IPv6 ACL for control-plane traffic policing for OSPFv3, in addition to the CoPP support for VRRP, BGP, and ICMP. ipv6 access-group Assign an IPv6 access-group to an interface.
PAGE 795
! interface TenGigabitEthernet 1/1/1/1 no ip address ipv6 access-group AclList1 in implicit-permit Vlan 10-20 no shutdown Dell(conf-if-te-1/1/1/1)# cam-acl-egress Allocate space for IPv6 egress ACLs. Syntax Parameters cam-acl-egress {default | l2acl 1-4 ipv4acl 1-4 ipv6acl 0-4} default l2acl 1-4 ipv4acl 1- 4 ipv6acl 0-4 Use the default CAM profile settings, and set the CAM as follows: • L2 ACL(l2acl): 1 • L3 ACL (ipv4acl: 1 • IPv6 L3 ACL (ipv6acl): 2 Allocate space to support IPv6 ACLs.
PAGE 796
Usage Information For the new settings to take effect, save the new CAM settings to the startup-config (write-mem or copy run start), then reload the system. The total amount of space allowed is 4 FP Blocks.
PAGE 797
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.2.0 Introduced on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 798
25 Intermediate System to Intermediate System (ISIS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 799
• hello padding • hostname dynamic • ignore-lsp-errors • ip router isis • ipv6 router isis • isis circuit-type • isis csnp-interval • isis hello-interval • isis hello-multiplier • isis hello padding • isis ipv6 metric • isis metric • isis network point-to-point • isis password • isis priority • is-type • log-adjacency-changes • lsp-gen-interval • lsp-mtu • lsp-refresh-interval • max-area-addresses • max-lsp-lifetime • maximum-paths • metric-style • multi-topo
PAGE 800
To disable adjacency check, use the no adjacency-check command. Defaults Enabled. Command Modes Command History Usage Information • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 801
prefix-list-name Defaults Enter the name of a configured IP prefix list. Routes meeting the criteria of the IP Prefix list are leaked. level1-into-level2 (Level 1 to Level 2 leaking is enabled.) level2–into-level1 (Level 2 to Level 1) leaking is disabled. Command Modes Command History Usage Information • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific.
PAGE 802
password Enter a 1 to 16-character length alphanumeric string to prevent unauthorized access or incorrect routing information corrupting the link state database. The password is processed as plain text, which only provides limited security. Defaults Not configured. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.
PAGE 803
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. Usage Information CAUTION: Use caution when you enter this command. Back up your configuration prior to using this command or your IS-IS configuration will be erased.
PAGE 804
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. clns host Define a name-to-network service mapping point (NSAP) that you use with commands that require NSAPs and system IDs. Syntax clns host name nsap Parameters name Enter an alphanumeric string to identify the name-to-NSAP mapping. nsap Enter a specific NSAP address that is associated with the name parameter.
PAGE 805
debug isis Enable debugging for all IS-IS operations. Syntax debug isis To disable debugging of IS-IS, use the no debug isis command. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 806
Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable the debug information on IS-IS for an adjacency tied to that VRF. This command displays the IIH related debug details. interface (OPTIONAL) Identifies the interface type and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 807
To turn off debugging, use the no debug isis [vrf vrf—name] updates [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF. This information contains local updates tied to the VRF that you specify. This command displays the local LSP debugging details of the current unit.
PAGE 808
debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. Syntax debug isis [vrf vrf-name] snp-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name] snp-packets [interface] command.
PAGE 809
Version Description 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. Syntax debug isis [vrf vrf-name] spf-triggers To turn off debugging, use the no debug isis [vrf vrf-name] spf-triggers command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging information on IS-IS corresponding to that VRF.
PAGE 810
debug isis update-packets Enable debugging on link state PDUs (LSPs) that a router detects. Syntax debug isis [vrf vrf-name] update-packets [interface] To turn off debugging, use the no debug isis update-packets [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS. This information contains updates from neighbors tied to the VRF that you specify.
PAGE 811
Version Description 8.3.12.0 Introduced on the S4810. 6.3.1.0 Introduced. default-information originate Generates a default route into an IS-IS routing domain and controls the distribution of default information. Syntax default-information originate [always] [metric metric] [route-map map-name] To disable the generation of a default route into the specified IS-IS routing domain, use the no defaultinformation originate [always] [metric metric] [route-map map-name] command.
PAGE 812
Usage Information When you use this command to redistribute routes into a routing domain, the router becomes an autonomous system (AS) boundary router. An AS boundary router does not always generate a default route into a routing domain. The router still requires its own default route before it can generate one. How a metric value assigned to a default route advertises depends on the metric-style command configuration.
PAGE 813
distance Define the administrative distance for learned routes. Syntax distance weight [ip-address mask [prefix-list]] To return to the default values, use the no distance weight command. Parameters Defaults Command Modes Command History Usage Information weight The administrative distance value indicates the reliability of a routing information source. The range is from 1 to 255. (A higher relative value indicates lower reliability. Routes with smaller values are given preference.
PAGE 814
distribute-list in Filter network prefixes received in updates. Syntax distribute-list prefix-list-name in [interface] To return to the default values, use the no distribute-list prefix-list-name in [interface] command. Parameters Defaults Specify the prefix list to filter prefixes in routing updates. interface (OPTIONAL) Identifies the interface type and the interface following: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 815
Related Commands Version Description 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. • distribute-list out — suppress networks from being advertised in updates. • redistribute — redistribute routes from one routing domain to another routing domain. distribute-list out Suppress network prefixes from being advertised in outbound updates.
PAGE 816
Usage Information Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. You can assign a name to a routing process so a prefix list IS applied to only the routes derived from the specified routing process. • distribute-list in — filter the networks received in updates. • redistribute — redistribute routes from one routing domain to another routing domain.
PAGE 817
domain-password Set the authentication password for a routing domain. Syntax domain-password [hmac-md5 | encryption-type] password To disable the password, use the no domain-password command. Parameters hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. encryption-type (OPTIONAL) Enter 7 to encrypt the password using DES. password Enter an alphanumeric string up to 16 characters long.
PAGE 818
graceful-restart ietf Enable graceful restart on an IS-IS router. Syntax graceful-restart ietf To return to the default, use the no graceful-restart ietf command. Parameters ietf Enter ietf to enable graceful restart on the IS-IS router. Defaults Graceful restart disabled. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 819
To return to the default, use the no graceful-restart interval command. Parameters minutes Enter the graceful-restart interval minutes. The range is from 1 to 20 minutes. The default is 5 minutes. Defaults 5 minutes Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 820
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 821
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize.
PAGE 822
graceful-restart t3 Configure the overall wait time before graceful restart completes. Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command. Parameters adjacency Enter the keyword adjacency so that the restarting router receives the remaining time value from its peer and adjusts its T3 value so if you have configured this option. manual Enter the keyword manual to specify a time value that the restarting router uses.
PAGE 823
hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | point-to-point] command. Parameters multi-point (OPTIONAL) Enter the keywords multi-point to pad only LAN hello PDUs. point-to-point (OPTIONAL) Enter the keywords point-to-point to pad only point-to-point PDUs.
PAGE 824
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 825
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. IS-IS normally purges LSPs with an incorrect data link checksum causing the LSP source to regenerate the message. A cycle of purging and regenerating LSPs can occur when a network link continues to deliver accurate LSPs even though there is a link causing data corruption. This process could cause disruption to your system operation.
PAGE 826
NOTE: IP address is not mandatory for forming IS-IS adjacency. Related Commands • net — configure an IS-IS network entity title (NET) for the routing process. • router isis — enable the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process. Syntax ipv6 router isis [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters tag Defaults Not configured.
PAGE 827
isis circuit-type Configure the adjacency type on interfaces. Syntax isis circuit-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no isis circuit-type command. Parameters level-1 You can form a Level 1 adjacency if there is at least one common area address between this system and neighbors. You cannot form Level 2 adjacencies on this interface.
PAGE 828
isis csnp-interval Configure the IS-IS complete sequence number PDU (CSNP) interval on an interface. Syntax isis csnp-interval seconds [level-1 | level-2] To return to the default values, use the no isis csnp-interval [seconds] [level-1 | level-2] command. Parameters seconds Interval of transmission time between CSNPs on multi-access networks for the designated intermediate system. The range is from 0 to 65535. The default is 10.
PAGE 829
To return to the default values, use the no isis hello-interval [seconds] [level-1 | level-2] command. Parameters seconds Allows you to set the length of time between hello packet transmissions. The range is from 1 to 65535. The default is 10. level-1 (OPTIONAL) Select this value to configure the hello interval for Level 1. This value is the default. level-2 (OPTIONAL) Select this value to configure the hello interval for Level 2.
PAGE 830
Parameters multiplier Specifies an integer that sets the multiplier for the hello holding time. Never configure a hello-multiplier lower than the default (3). The range is from 3 to 1000. The default is 3. level-1 (OPTIONAL) Select this value to configure the hello multiplier independently for Level 1 adjacencies. This value is the default. level-2 (OPTONAL) Select this value to configure the hello multiplier independently for Level 2 adjacencies.
PAGE 831
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 832
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Dell Networking recommends configuring metrics on all interfaces.
PAGE 833
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Dell Networking recommends configuring metrics on all interfaces.
PAGE 834
isis password Configure an authentication password for an interface. Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [password] [level-1 | level-2] command. Parameters encryption-type (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password.
PAGE 835
isis priority Set the priority of the designated router you select. Syntax isis priority value [level-1 | level-2] To return to the default values, use the no isis priority [value] [level-1 | level-2] command. Parameters value This value sets the router priority. The higher the value, the higher the priority. The range is from 0 to 127. The default is 64. level-1 (OPTIONAL) Specify the priority for Level 1. This setting is the default. level-2 (OPTIONAL) Specify the priority for Level 2.
PAGE 836
is-type Configure IS-IS operating level for a router. Syntax is-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no is-type command. Parameters level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. Defaults level-1-2 Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 837
Defaults Adjacency changes are not logged. Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500.
PAGE 838
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 839
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement.
PAGE 840
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The refresh interval determines the rate at which route topology information is transmitted preventing the information from becoming obsolete.
PAGE 841
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. To configure the number of area addresses on router, use this command. This value must be consistent with routers in the same area, otherwise the router forms only Level 2 adjacencies. The value must be same among all the routers to form Level 1 adjacencies.
PAGE 842
Related Commands • lsp-refresh-interval — set the link-state packet (LSP) refresh interval. maximum-paths Allows you to configure the maximum number of equal cost paths allowed in a routing table. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 addresses. Syntax maximum-paths number To return to the default values, use the no maximum-paths command.
PAGE 843
To return to the default values, use the no metric-style {narrow [transition] | transition | wide [transition]} [level-1 | level-2] command. Parameters narrow Allows you to generate and accept old-style TLVs. The metric range is from 0 to 63. transition Allows you to generate both old-style and new-style TLVs. The metric range is from 0 to 63. wide Allows you to generate and accept only new-style TLVs. The metric range is from 0 to 16777215. level-1 Enables the metric style on Level 1.
PAGE 844
multi-topology Enables multi-topology IS-IS. It also allows enabling/disabling of old and new style TLVs for IP prefix information in the LSPs. Syntax multi-topology [transition] To return to a single topology configuration, use the no multi-topology [transition] command. Parameters transition Defaults Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific.
PAGE 845
Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 846
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 847
route-map mapname Defaults Command Modes Command History Usage Information (OPTIONAL) If you do not enter the route-map argument, all routes are redistributed. If a map-name value is not specified, no routes are imported. • metric metric-value = 0 • metric-type= internal; level-2 • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific.
PAGE 848
• distribute-list out — suppress networks from being advertised in updates. This command filters redistributed routing information. redistribute bgp Redistribute routing information from a BGP process. Syntax redistribute bgp AS number [level-1| level-1-2 | level-2] [metric metric-value] [metric-type {external| internal}] [route-map map-name] To return to the default values, use the no redistribute bgp command with the appropriate parameters.
PAGE 849
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added support for IPv6 ISIS. 6.3.1.0 Introduced. Usage Information BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command.
PAGE 850
level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes. This setting is the default. match {external | internal} (OPTIONAL) The command used for OSPF to route and redistribute into other routing domains. The values are route-map mapname • internal • external map-name is an identifier for a configured route map. The route map should filter imported routes from the source routing protocol to the current routing protocol.
PAGE 851
router isis Allows you to enable the IS-IS routing protocol and to specify an IP IS-IS process. Syntax router isis [vrf vrf-name] [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to enable the IS-IS routing protocol and to specify an IP IS-IS process on that VRF. tag (OPTIONAL) This is a unique name for a routing process. A null tag is assumed if the tag option is not specified.
PAGE 852
• net — configure an IS-IS network entity title (NET) for a routing process. • is-type — assign a type for a given area. set-overload-bit To set the overload bit in zeroth fragment of non-pseudonode LSPs on the router, configure the router. This setting prevents other routers from using it as an intermediate hop in their shortest path first (SPF) calculations. Syntax set-overload-bit To return to the default values, use the no set-overload-bit command. Defaults Not set.
PAGE 853
show config Display the changes you made to the IS-IS configuration. Default values are not shown. Syntax Command Modes Command History Example (RouterIsis) show config • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.
PAGE 854
spf-interval level-2 120 20 25 exit-address-family show isis database Display the IS-IS link state database. Syntax show isis [vrf vrf-name] database [level-1 | level-2] [local] [detail | summary] [system-id] [lspid] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IS-IS link state database corresponding to that VRF. NOTE: If you do not specify this option, the IS-IS link state database corresponding to the default VRF are displayed.
PAGE 855
Usage Information Version Description 8.3.7.1 Introduced on the S4810. The following describes the show isis database command shown in the following example. Field Description IS-IS Level-1/ Level-2 Link State Database Displays the IS-IS link state database for Level 1 or Level 2. LSPID Displays the LSP identifier. The first six octets are the System ID of the originating router. The first six octets are the System ID of the originating router. The next octet is the pseudonode ID.
PAGE 856
! Dell# show isis database detail ISIS.00-00 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002B 0x853B 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.1 IPv6 Address: 1011::1 Topology: IPv4 (0x00) IPv6 (0x8002) Metric: 10 IS OSPF.00 Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 15.1.1.0 255.255.255.
PAGE 857
Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name if the VRf to display IS-IS graceful restart details corresponding to that VRF. NOTE: If you do not specify this option, the IS-IS graceful restart details corresponding to the default VRF are displayed. Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 858
show isis hostname Display IS-IS host names configured or learned on the switch. Syntax show isis [vrf vrf-name] hostname Parameters Command Modes Command History Example vrf vrf-name • EXEC • EXEC Privilege Enter the keyword vrf followed by the name of the VRF to display IS-IS host names corresponding to that VRF. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 859
Parameters Command Modes Command History Example vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS interface status information corresponding to that VRF. interface (OPTIONAL) Enter the following keywords and the interface information: • EXEC • EXEC Privilege • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 860
Number of active level-2 adjacencies: 1 Next IS-IS LAN Level-1 Hello in 2 seconds Next IS-IS LAN Level-2 Hello in 1 seconds LSP Interval: 33 TenGigabitEthernet 1/1/2/1 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 38371358, Local circuit ID 2 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 861
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 862
show isis protocol Display IS-IS routing information. Syntax show isis [vrf vrf-name] protocol Parameters Command Modes Command History Example vrf vrf-name • EXEC • EXEC Privilege (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS routing information corresponding to that VRF. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 863
Accept wide metrics: none Multi Topology Routing is enabled in transition mode. Dell# show isis traffic This command allows you to display IS-IS traffic interface information. Syntax Parameters Command Modes Command History show isis [vrf vrf-name] traffic [interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display IS-IS traffic interface information corresponding to that VRF.
PAGE 864
Usage Information Example 864 Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. The following describes the show isis traffic command shown in the following example. Item Description Level-1/Level-2 Hellos (sent/rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/ rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs.
PAGE 865
spf-interval Specify the minimum interval between shortest path first (SPF) calculations. Syntax spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command.
PAGE 866
Usage Information This command spf-interval in CONFIG-ROUTER-ISIS-AF-IPV6 mode is used for IPv6 Multi-Topology route computation only. If using Single Topology mode, use the spf-interval command in CONFIG-ROUTER-ISIS mode for both IPv4 and IPv6 route computations. SPF throttling slows down the frequency at which route calculations are performed during network instability.
PAGE 867
26 iSCSI Optimization Internet small computer system interface (iSCSI) optimization enables quality-of-service (QoS) treatment for iSCSI storage traffic on an S6100–ON system. To configure and verify the iSCSI optimization feature, use the following Dell Networking OS commands.
PAGE 868
Usage Information You can configure iSCSI TLVs to send either globally or on a specified interface. The interface configuration takes priority over global configuration. iscsi aging time Set the aging time for iSCSI sessions. Syntax iscsi aging time time To remove the iSCSI session aging time, use the no iscsi aging time command. Parameters time Enter the aging time for the iSCSI session. The range is from 5 to 43,200 minutes.
PAGE 869
dscp dscp-value Enter the DSCP value assigned to the incoming packets in an iSCSI session. The valid range is from 0 to 63. The default is: the DSCP value in ingress packets is not changed. remark Marks the incoming iSCSI packets with the configured dot1p or DSCP value when they egress to the switch. The default is: the dot1and DSCP values in egress packets are not changed. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 870
iscsi priority-bits Configure the priority bitmap that advertises in the iSCSI application TLVs. Syntax iscsi priority-bits To remove the configured priority bitmap, use the no iscsi priority-bits command. Defaults 4 (0x10 in the bitmap) Command Modes PROTOCOL LLDP (only on the global, not on the interface) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 871
iscsi target port Configure the iSCSI target ports and optionally, the IP addresses on which iSCSI communication is monitored. Syntax iscsi target port [tcp-port-2...tcp-port-16]ip-address [ip-address] To remove the configured iSCSI target ports or IP addresses, use the no iscsi target port command. Parameters tcpport-2...tcpport- 16 Enter the tcp-port number of the iSCSI target ports. The tcp-port-n is the TCP port number or a list of TCP port numbers on which the iSCSI target listens to requests.
PAGE 872
Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module.
PAGE 873
-----------------------------------------------------Target: iqn.2001-05.com.equallogic:0-8a0906-0e70c2002-10a0018426a48c94-iom010 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000 Session 1: --------------------------------------------------------Target: iqn.2001-05.com.equallogic:0-8a0906-0f60c2002-0360018428d48c94-iom011 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000.
PAGE 874
Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.44 33345 10.10.0.101 3260 0 Session 1 : ---------------------------------------------------Target:iqn.2010-11.com.ixia:ixload:iscsi-TG1 Initiator:iqn.2010-11.com.ixia.ixload:initiator-iscsi-35 Up Time:00:00:01:22(DD:HH:MM:SS) Time for aging out:00:00:09:31(DD:HH:MM:SS) ISID:806978696102 Initiator Initiator Target Target Connection IP Address TCP Port IP Address TCPPort ID 10.10.0.53 33432 10.10.0.
PAGE 875
27 Link Aggregation Control Protocol (LACP) This section contains commands for Dell Networks’ implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking OS. NOTE: For static LAG commands based on the standards specified in the IEEE 802.3 Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications, see Port Channel Commands .
PAGE 876
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • show lacp — display the LACP configuration.
PAGE 877
• Defaults Command Modes Command History Transmit enter out None • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 878
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 879
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp system-priority Configure the LACP system priority.
PAGE 880
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. port-channel-protocol lacp Enable LACP on any LAN port. Syntax port-channel-protocol lacp To disable LACP on a LAN port, use the no port-channel-protocol lacp command. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 881
show lacp Display the LACP matrix. Syntax Parameters Defaults Command Modes Command History Example (PortChannel-Number) show lacp port-channel-number [sys-id | counters] port-channelnumber Enter a port-channel number. The range is from 1 to 4096. sys-id (OPTIONAL) Enter the keywords sys-id and the value that identifies a system. counters (OPTIONAL) Enter the keyword counters to display the LACP counters. Without a Port Channel specified, the command clears all Port Channel counters.
PAGE 882
A-Active LACP, B-Passive LACP, C-Short Timeout, D-Long Timeout E-Aggregatable Link, F-Individual Link, G-IN_SYNC, H-OUT_OF_SYNC I-Collection enabled, J-Collection disabled, K-Distribution enabled LDistribution disabled, M-Partner Defaulted, N-Partner Non-defaulted, O-Receiver is in expired state, P-Receiver is not in expired state Port Te 1/1/6/1 is enabled, LACP is Actor Admin: State ACEHJLMP Key Oper: State ACEGIKNP Key Partner Admin: State BDFHJLMP Key Oper: State BCEGIKNP Key Dell# Example (Sys-id) ena
PAGE 883
28 Layer 2 This section describes commands to configure Layer 2 features. MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table. Syntax Parameters mac-address-table aging-time seconds seconds Enter either zero (0) or a number as the number of seconds before MAC addresses are relearned. To disable aging of the MAC address table, enter 0.
PAGE 884
Related Commands Version Description 8.3.1.0 On the E-Series, available in INTERFACE VLAN context, reduced the minimum aging time in the INTERFACE VLAN context from 10 seconds to 1 second. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. • mac learning-limit — set the MAC address learning limits for a selected interface. • show mac-address-table aging-time — display the MAC aging time.
PAGE 885
Related Commands Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. • mac learning-limit — set the MAC address learning limits for a selected interface. • show mac-address-table aging-time — display the MAC aging time. mac-address-table static Associate specific MAC or hardware addresses to an interface and VLANs.
PAGE 886
vlan vlan-id • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a port channel interface, enter the keywords port-channel then a number. Enter the keyword vlan then a VLAN ID number from 1 to 4094.
PAGE 887
To disable the ARP refresh feature, use the no mac-address-table station-move refresh-arp command. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.9(0.0) Modified the default option from none to Enabled. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 888
station-moveviolation Defaults • (OPTIONAL) Enter the keywords station-move to allow a station move on learned MAC addresses. On S-Series, the default behavior is dynamic. NOTE: “Static” means manually entered addresses, which do not age. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON.
PAGE 889
NOTE: If you configure this command on an interface in a routed VLAN, and after the MAC addresses learned reaches the limit set in the mac learning-limit command, IP protocols are affected. For example, VRRP sets multiple VRRP Masters and OSPF may not come up. When a channel member is added to a port-channel and there is not enough ACL CAM space, the MAC limit functionality on that port-channel is undefined.
PAGE 890
Usage Information Related Commands Version Description 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. This command is supported on physical interfaces, static LAGs, and LACP LAGs. • show mac learning-limit — display details of the mac learning-limit. mac learning-limit mac-address-sticky Maintain the dynamically learned mac addresses as sticky MAC addresses on the selected port.
PAGE 891
mac learning-limit station-move-violation Specify the actions for a station move violation. Syntax mac learning-limit station-move-violation {log | shutdown-both | shutdownoffending | shutdown-original} To disable a configuration, use the no mac learning-limit station-move-violation command, then the configured keyword. Parameters log Enter the keyword log to generate a syslog message on a station move violation.
PAGE 892
Related Commands • show mac learning-limit — display details of the mac learning-limit. mac learning-limit reset Reset the MAC address learning-limit error-disabled state. Syntax mac learning-limit reset Defaults none Command Modes Command History 892 Layer 2 • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.
PAGE 893
show mac-address-table Display the MAC address table. Syntax Parameters Command Modes show mac-address-table [address mac-address | interface interface | vlan vlanid] [aging-time] [dynamic | static] [count [vlan vlan-id] [interface interfacetype [slot [/port[/subport]]]]] address macaddress (OPTIONAL) Enter the keyword address then a MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address.
PAGE 894
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 895
2 2 Usage Information Example (Count) Related Commands 00:00:00:00:00:03 00:00:00:00:00:04 Dynamic Dynamic Po 100 Po 10 Active Active The following describes the show mac-address-table count command shown in the following example. Line Beginning With Description MAC Entries... Displays the number of MAC entries learned per VLAN. Dynamic Address... Lists the number of dynamically learned MAC addresses. Static Address... Lists the number of user-defined MAC addresses. Total MAC...
PAGE 896
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 7.7.1.0 Introduced on the C-Series and S-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 897
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000.
PAGE 898
To remove the default VLAN status from a VLAN and VLAN 1 does not exist, use the no default vlan-id vlan-id syntax. Parameters vlan-id Enter the VLAN ID number of the VLAN to become the new Default VLAN. The range is from 1 to 4094. The default is 1. Defaults Default VLAN is VLAN 1. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 899
Parameters description Defaults none Command Modes INTERFACE VLAN Command History Related Commands Enter a text string description to identify the VLAN (80 characters maximum). Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 900
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced The no default vlan disable command is not listed in the running-configuration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters vlan-name Enter up to 32 characters as the name of the VLAN. Defaults Not configured.
PAGE 901
Related Commands • interface vlan — configure a VLAN. • show vlan — display the current VLAN configurations on the switch. show config Display the current configuration of the selected VLAN. Syntax show config Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 902
show vlan Display the current VLAN configurations on the switch. Syntax show vlan [brief | id vlan-id | name vlan-name] Parameters Command Modes Command History 902 Layer 2 brief (OPTIONAL) Enter the keyword brief to display the following information: • VLAN ID • VLAN name (left blank if none is configured) • Spanning Tree Group ID • MAC address aging time • IP address id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094.
PAGE 903
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. The following describes the show vlan command shown in the following example. Column Heading Description (Column 1 — no heading) asterisk symbol (*) = Default VLAN • G = GVRP VLAN • P = primary VLAN • C = community VLAN • I = isolated VLAN • O = OpenFlow NUM Displays existing VLAN IDs.
PAGE 904
* Example (VLAN ID) NUM 1 2 Status Inactive Active Description 3 Active T Po20(Te 1/1/6/1) 4 Active U Po2(Te 1/1/2/1) 5 Active T Po20(Te 1/1/6/1) 6 Active U Po3(Te 1/1/4/1) 7 Active T Po20(Te 1/1/6/1) P 100 Active T Po1(Te 1/1/1/1) C 101 I 102 Dell# Inactive T Te 1/1/3/1 Inactive T Te 1/1/4/1 Q Ports U Po1(Te 1/1/1/1) T Po20(Te 1/1/6/1), Te 1/1/5/2 T Te 1/1/7/1 T Te 1/1/7/1 U Te 1/1/1/1 T Po20(Te 1/1/6/1) T Te 1/1/7/1 T Te 1/1/7/1 U Te 1/1/3/1 T Po20(Te 1/1/6/1) T Te 1/1/7/1 T Te 1/1/7/1
PAGE 905
Dell(conf-if-vl-222)#do show vlan name test Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM Status Description 222 Inactive Dell(conf-if-vl-222)# Example (OpenFlow instance) * O O O Related Commands NUM 1 3 6 8 12 Status Inactive Inactive Inactive Inactive Inactive Q Ports U Te 1/1/2/1 Description Q Ports O Te 1/1/1/1 • vlan-stack compatible — enable the Stackable VLAN feature on the selected VLAN.
PAGE 906
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.
PAGE 907
• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a port channel interface, enter the keywords port-channel then a number. Defaults Not configured.
PAGE 908
untagged Add a Layer 2 interface to a VLAN as an untagged interface. Syntax untagged interface To remove an untagged interface from a VLAN, use the no untagged interface command. Parameters interface Enter the following keywords and the interface information: • For a port channel interface, enter the keywords port-channel then a number. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 909
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Untagged interfaces can only belong to one VLAN. In the Default VLAN, you cannot use the no untagged interface command. To remove an untagged interface from all VLANs, including the Default VLAN, enter INTERFACE mode and use the no switchport command. Related Commands • interface vlan — configure a VLAN. • tagged — specify which interfaces in a VLAN are tagged.
PAGE 910
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 911
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
PAGE 912
Version Description 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information Related Commands FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. • fefd reset — clear an interface in Err-disabled state. It doesn’t work until the interface is in err-disabled state. • fefd mode — change FEFD mode on an interface. fefd interval Set an interval between control packets.
PAGE 913
fefd mode Change the FEFD mode on an interface. Syntax fefd mode {normal | aggressive}] To return the FEFD mode to the default of normal, use the no fefd mode command. Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol.
PAGE 914
Parameters interface (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information.
PAGE 915
Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 916
Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 917
• Command Modes Command History • EXEC • EXEC Privilege For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 918
Te 1/1/1/1 Te 1/1/2/1 Te 1/1/3/1 Te 1/1/4/1 Te 1/1/5/1 Te 1/1/6/1 Te 1/1/7/1 Te 1/1/8/1 Dell# Related Commands 918 Layer 2 Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive Aggressive 10 10 10 10 10 10 10 10 Admin Admin Admin Admin Admin Admin Admin Admin Shutdown Shutdown Shutdown Shutdown Shutdown Shutdown Shutdown Shutdown • fefd — enable far-end failure detection. • fefd disable — disable FEFD on an interface only.
PAGE 919
29 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell Networking operating software implementation of LLDP is based on IEEE standard 801.1ab. The Dell Networking OS supports the basic LLDP commands on platform.
PAGE 920
Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 921
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.
PAGE 922
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.
PAGE 923
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.
PAGE 924
events Enter the keyword events to display major events such as timer events. packet Enter the keyword packet to display information regarding packets coming in or going out. brief Enter the keyword brief to display brief packet information. detail Enter the keyword detail to display detailed packet information. tx Enter the keyword tx to display transmit-only packet information. rx Enter the keyword rx to display receive-only packet information.
PAGE 925
Defaults Enabled — no disable. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 926
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 927
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. • protocol lldp (Configuration) — enable LLDP globally.
PAGE 928
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Configuration) Enable the LLDP globally on the switch. Syntax protocol lldp To disable LLDP globally on the chassis, use the no protocol lldp command. Defaults Enabled.
PAGE 929
protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.
PAGE 930
show lldp neighbors Display LLDP neighbor information for all interfaces or a specified interface. Syntax show lldp neighbors [interface interface] [detail] Parameters interface interface detail (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 931
Usage Information Version Description 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval. Example show lldp statistics Display the LLDP statistical information. Syntax show lldp statistics Defaults None Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 932
LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands. Dell Networking OS LLDP-MED commands are an extension of the set of LLDP TLV advertisement commands. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so that endpoint devices and network connectivity devices can advertise their characteristics and configuration information.
PAGE 933
Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 934
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 935
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 936
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series.
PAGE 937
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 938
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 939
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 940
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 941
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000.
PAGE 942
Command History Related Commands 942 This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 943
30 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 944
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.3(0.0) Added support for association of an IP address with multicast MAC address on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 945
• output-range interface vlan vlan-id For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. For a multicast MAC address, enter the keyword output-range then one of the following interfaces to indicate a range of ports for which traffic is forwarded: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 946
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL platforms. Default Disabled Usage Information By default this command is disabled.
PAGE 947
31 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM sparse-mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell Networking OS supports MSDP commands on the platform.
PAGE 948
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 949
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.
PAGE 950
Version Description 8.3.7.1 Introduced on the S4810. 7.8.1.0 Added the local option. 7.7.1.0 Added the rejected-sa option. 6.2.1.1 Introduced ip msdp cache-rejected-sa Enable an MSDP cache for the rejected source-active entries. Syntax ip msdp cache-rejected-sa {number} To clear the MSDP rejected source-active entries, use the no ip msdp cache-rejected-sa {number} command then the ip msdp cache-rejected-sa {number} command. Parameters number Enter the number of rejected SA entries to cache.
PAGE 951
ip msdp default-peer Define a default peer from which to accept all source-active (SA) messages. Syntax ip msdp default-peer peer address [list name] To remove the default peer, use the no ip msdp default-peer {peer address} list name command. Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.) list name Enter the keywords list name and specify a standard access list that contains the RP address that should be treated as the default peer.
PAGE 952
ip msdp log-adjacency-changes Enable logging of MSDP adjacency changes. Syntax ip msdp log-adjacency-changes To disable logging, use the no ip msdp log-adjacency-changes command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 953
peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 954
• For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 955
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 956
If the total number of SA messages received from the peer is already larger than the limit when this command is applied, those SA messages continue to be accepted. To enforce the limit in such situation, use the clear ip msdp peer command to reset the peer. Related Commands • ip msdp sa-limit — configure the MSDP SA Limit. • clear ip msdp peer — clear the MSDP peer. • show ip msdp — display the MSDP information. ip msdp redistribute Filter local PIM SA entries in the SA cache.
PAGE 957
To apply the redistribute filter to entries already present in the SA cache, use the clear ip msdp sa-cache local command. ip msdp sa-filter Permit or deny MSDP source active (SA) messages based on multicast source and/or group from the specified peer. Syntax ip msdp sa-filter {in | out} peer-address list [access-list name] Remove this configuration using the no ip msdp sa-filter {in | out} peer address list [access-list name] command.
PAGE 958
ip msdp sa-limit Configure the upper limit of source-active (SA) entries in SA-cache. Syntax ip msdp sa-limit number To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache. The range is from 1 to 500000. Defaults 50000 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 959
ip msdp shutdown Administratively shut down a configured MSDP peer. Syntax Parameters ip msdp shutdown {peer address} peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 960
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 961
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced Dell# show ip msdp peer 100.1.1.1 Peer Addr: 100.1.1.1 Local Addr: 100.1.1.
PAGE 962
Command History Example 962 This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.
PAGE 963
32 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking OS, conforms to IEEE 802.1s. This command supports the Dell Networking platform.
PAGE 964
• For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 965
disable Globally disable the multiple spanning tree protocol on the switch. Syntax disable To enable MSTP, enter the no disable command. Defaults Disabled. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 966
To return to the default setting, use the no forward-delay command. Parameters seconds Enter the number of seconds the interface waits in the Blocking State and the Learning State before transiting to the Forwarding State. The range is from 4 to 30. The default is 15 seconds. Defaults 15 seconds Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 967
Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10. The default is 2 seconds. Defaults 2 seconds Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 968
Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 969
Valid priority values are: 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, and 61440. All other values are rejected. Defaults default bridge-priority is 32768. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 970
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 971
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 972
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 973
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series.
PAGE 974
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Usage Information Enable the multiple spanning tree protocol prior to using this command.
PAGE 975
Version Description 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Support for the optional keyword guard was added on the C-Series, S-Series, and ESeries. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) loopback BPDU inconsistency causes. Usage Information Enable the multiple spanning tree protocol prior to using this command.
PAGE 976
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID -----------------------------------------------------------Te 1/1/1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge Boundary -----------------------------------------------------------Te 1/1/1/1 ErrDis 128.257 128 20000 EDS 0 P2P No No Dell# show spanning-tree msti 0 MSTI 0 VLANs mapped 1-4094 Root Identifier has priority 32768, Address 0001.e801.
PAGE 977
spanning-tree Enable the multiple spanning tree protocol on the interface. Syntax spanning-tree To disable the multiple spanning tree protocol on the interface, use the no spanning-tree command. Parameters spanning-tree Enter the keywords spanning-tree to enable the MSTP on the interface. Defaults Enable. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 978
Parameters msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 979
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 980
33 Multicast The multicast commands are supported by Dell Networking OS on all platform. IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 981
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • show ip pim tib — show the PIM tree information base. ip mroute Assign a static mroute.
PAGE 982
ip-address (OPTIONAL) Enter the IP address in dotted decimal format of the RPF neighbor. distance (OPTIONAL) Enter a number as the distance metric assigned to the mroute. The range is from 0 to 255. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 983
Usage Information Version Description 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the S6100–ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.
PAGE 984
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 985
Enter a VLAN ID to limit the information displayed to the multicast routes PIM-SM snooping discovers on a specified VLAN. The VLAN ID range is from 1 to 4094. Enter a multicast group address and, optionally, a source multicast address in dotted decimal format (A.B.C.D) to limit the information displayed to the multicast routes PIMSM snooping discovers for a specified multicast group and source. Command Modes Command History summary (OPTIONAL) Enter the keyword summary to view a summary of all routes.
PAGE 986
IPv4 Multicast Snooping Table (*, 224.0.0.0), uptime 17:46:23 Incoming vlan: Vlan 2 Outgoing interface list: TenGigabitEthernet 1/1/3/1 (*, 225.1.2.1), uptime 00:04:16 Incoming vlan: Vlan 2 Outgoing interface list: TenGigabitEthernet 1/1/1/1 TenGigabitEthernet 1/1/3/1 (165.87.1.7, 225.1.2.
PAGE 987
(*, 224.20.20.1), uptime 00:05:12 Incoming interface: TenGigabitEthernet 1/1/2/1 Outgoing interface list: TenGigabitEthernet 1/1/4/1 show ip rpf View reverse path forwarding. Syntax Command Modes Command History show ip rpf • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 988
34 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 989
clear ipv6 neighbors Delete all entries in the IPv6 neighbor discovery cache or neighbors of a specific interface. Static entries are not removed using this command. Syntax Parameters clear ipv6 neighbors [vrf vrf-name] [ipv6-address | interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to clear the neighbor corresponding to that VRF. NOTE: If you do not specify this option, the neighbors in the default VRF are cleared.
PAGE 990
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. debug ipv6 nd ra–guard Enable debugging for IPv6 RA guard snooping information.
PAGE 991
device–role Specify the role of the device attached to the port. Syntax device-role {host | router} To reset the device role, use the no device-role {host | router} command. Parameters host Enter the keyword host to set the device-role as host. router Enter the keyword router to set the device-role as router. Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
PAGE 992
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 993
Related Commands • show ipv6 nd ra-guard policy — display the configuration applied on all the RA guard policies or a specific RA guard policy. ipv6 nd ra–guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 994
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. • ipv6 nd ra-guard enable — configure the RA guard related commands. ipv6 neighbor Configure a static entry in the IPv6 neighbor discovery.
PAGE 995
Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 996
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.
PAGE 997
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, and Z9000 switches. • ipv6 nd ra-guard enable — configure the RA guard related commands. • ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode.
PAGE 998
• ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode. mtu Enable the verification of the configured maximum transmission unit (MTU) value in the received RA packets. Syntax mtu value To reset the MTU value, use the no mtu value command. Parameters value Enter the maximum transmission unit value in bytes. The range is from 1,280 to 11,982 bytes.
PAGE 999
Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1000
Related Commands Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. • ipv6 nd ra-guard enable — configure the RA guard related commands. • ipv6 nd raguard policy policy-name — define the RA guard policy name and enter the RA guard policy configuration mode. retrans-time Enable the verification of the configured retransmission timer value in the received RA packets.
PAGE 1001
Defaults None Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.11(0.0) Introduced on the C9010. 9.10(0.0) Introduced on the S6100-ON. 9.9(0.0) Introduced on the Z9500. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1002
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000-ON, and Z9000 switches. • ipv6 nd ra-guard enable — configure the RA guard related commands. • ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. show config Display the RA guard policy mode configurations.
PAGE 1003
• other-config-flag — enable the verification of the advertised other configuration parameter. • reachable-time — set the advertised reachability time. • retrans-timer — set the advertised retransmission time. • router-preference maximum — enable the verification of the advertised default router preference (DRP) value. • trusted-port — apply the policy to trusted ports. show ipv6 nd ra–guard policy Display the configurations applied on all the RA guard policies or a specific RA guard policy.
PAGE 1004
• ipv6 nd raguard attach-policy — apply the IPv6 RA guard to a specific interface. show ipv6 neighbors Display IPv6 discovery information. Entering the command without options shows all IPv6 neighbor addresses stored on the control processor (CP). Syntax show ipv6 neighbors [vrf vrf-name] [ipv6-address| interface interface] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and the name of the VRF to display the neighbors corresponding to that VRF.
PAGE 1005
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810.
PAGE 1006
Usage Information Related Commands 1006 Use this command to disable all the RA guard policies. • ipv6 nd ra-guard enable — configure the RA guard related commands. • ipv6 nd raguard policy policy-name — define the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode.
PAGE 1007
35 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1008
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Example delay Configure the time delay used before communicating a change in the status of a tracked object to clients.
PAGE 1009
If the state of an object changes back to its former UP/DOWN state before the timer expires, the timer is cancelled and the client is not notified. For example, if the DOWN timer is running when an interface goes down and comes back up, the DOWN timer is cancelled and the client is not notified of the event. If the timer expires and an object’s state has changed, a notification is sent to the client.
PAGE 1010
show running-config track Display the current configuration of tracked objects. Syntax show running-config track [object-id] Parameters object-id (OPTIONAL) Display information on the specified tracked object. The range is 1 to 500. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1011
• track ip route reachability – configure object tracking on the reachability of an IPv4 route. show track Display information about tracked objects, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object. Syntax Parameters show track [object-id [brief] | interface [brief] [vrf vrf-name] | ip route [brief] [vrf vrf-name] | resolution | vrf vrf-name [brief] | brief] object-id (OPTIONAL) Display information on the specified tracked object.
PAGE 1012
Example Output Description number changes, last change time Number of times that the state of the tracked object has changed and the time since the last change in hours:minutes:seconds. First hop interface Displays the type and slot/port number of the first-hop interface of the tracked route. Tracked by Client that is tracking an object’s state; for example, VRRP. Dell# show track Track 1 IP route 23.0.0.
PAGE 1013
threshold metric Configure the metric threshold used to determine the UP and/or DOWN state of a tracked IPv4 or IPv6 route. Syntax threshold metric {up number | down number} To return to the default setting, use the no threshold metric {up number | down number} command. Parameters up number Enter a number for the UP threshold to be applied to the scaled metric of an IPv4 or IPv6 route. The default UP threshold is 254.
PAGE 1014
Configure the UP and DOWN thresholds for each tracked route with the threshold metric command. The default UP threshold is 254; the default DOWN threshold is 255. The notification of a change in the state of a tracked object is sent when a metric value crosses a configured threshold. The tracking process uses a protocol-specific resolution value to convert the actual metric in the routing table to a scaled metric in the range 0 to 255.
PAGE 1015
Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for tunnel interface. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the routing state of an IPv4 Layer 2 interface: • The status of the IPv4 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IP address.
PAGE 1016
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced.
PAGE 1017
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the UP and/or DOWN threshold of an IPv4 route metric. In order for a route’s metric to be tracked, the route must appear as an entry in the routing table.
PAGE 1018
vrf vrf-name (Optional) E-Series only: You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1019
isis resolution-value Enter the resolution used to convert the metric in the routing table for ISIS routes to a scaled metric. ospf resolutionvalue Enter the resolution used to convert the metric in the routing table for OSPF routes to a scaled metric. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.
PAGE 1020
• debug track • delay • description • show running-config track • threshold metric • track interface line-protocol show track ipv6 route Display information about all tracked IPv6 routes, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1021
Example Output Description Tracked by Client that is tracking an object’s state; for example, VRRP.
PAGE 1022
Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. interface Enter one of the following values: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information.
PAGE 1023
track ipv6 route metric threshold Configure object tracking on the threshold of an IPv4 route metric. Syntax track object-id ipv6 route ipv6-address/prefix-len metric threshold To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. ipv6-address/ prefix-len Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128.
PAGE 1024
You configure the UP and DOWN thresholds for each tracked IPv6 route by using the threshold metric command. The default UP threshold is 254; the default DOWN threshold is 255. The notification of a change in the state of a tracked object is sent when a metric value crosses a configured threshold. Related Commands • show track ipv6 route – display information about tracked IPv6 routes, including configuration, current state, and clients which track the route.
PAGE 1025
When you configure IPv6 route reachability as a tracked object, the UP/DOWN state of the tracked route is also determined by the entry of the next-hop address in the ARP cache. A tracked route is considered to be reachable if there is an ARP cache entry for the route's next-hop address. If the next-hop address in the ARP cache ages out for a route tracked for its reachability, an attempt is made to regenerate the ARP cache entry to if the next-hop address appears before considering the route DOWN.
PAGE 1026
The protocol-specific resolution value calculates the scaled metric by dividing a route's cost by the resolution value set for the route protocol: Related Commands 1026 • For ISIS, you can set the resolution in the range 1 to 1000, where the default is 10. • For OSPF, you can set the resolution in the range 1 to 1592, where the default is 1. • The resolution value used to map static routes is not configurable. By default, Dell Networking OS assigns a metric of 0 to static routes.
PAGE 1027
36 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an interior gateway protocol (IGP), which means that it distributes routing information between routers in a single autonomous system (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1028
Defaults cost = 1; no areas are configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1029
default-informationoriginate (OPTIONAL) Allows external routing information to be imported into the NSSA by using Type 7 default. no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1030
not-advertise (OPTIONAL) Enter the keywords not-advertise to set the status to DoNotAdvertise (that is, the Type 3 summary-LSA is suppressed and the component networks remain hidden from other areas.) Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.
PAGE 1031
Parameters area-id Specify the OSPF area in dotted decimal format (A.B.C.D.) or enter a number from zero (0) to 65535. no-summary (OPTIONAL) Enter the keywords no-summary to prevent the ABR from sending summary Link State Advertisements (LSAs) into the stub area. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1032
Parameters ref-bw (OPTIONAL) Specify a reference bandwidth in megabits per second. The range is from 1 to 4294967. The default is 100 megabits per second. Defaults 100 megabits per second. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1033
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1034
neighbor router-id • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. • For Port Channel groups, enter the keywords port-channel then a number. (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.).
PAGE 1035
To cancel the debug command, use the no debug ip ospf command. Parameters process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared. vrf vrf-name Enter the keyword vrf to view debugging information on OSPF corresponding to that VRF. bfd (OPTIONAL) Enter the keyword bfd to debug only OSPF BFD information. event (OPTIONAL) Enter the keyword event to debug only OSPF event information.
PAGE 1036
Field Example 1036 Description • 1 - Hello packet • 2 - database description • 3 - link state request • 4 - link state update • 5 - link state acknowledgement l: Displays the packet length. rid: Displays the OSPF router ID. aid: Displays the Autonomous System ID. chk: Displays the OSPF checksum. aut: States if OSPF authentication is configured.
PAGE 1037
Dell# 08:14:24 : OSPF(100:00): Xmt. v:2 t:1(HELLO) l:44 rid:192.1.1.1 aid:0.0.0.1 chk:0xa098 aut:0 auk: keyid:0 to:Te 1/1/3/1 dst:224.0.0.5 netmask:255.255.255.0 pri:1 N-, MC-, E+, T-, hi:10 di:40 dr:90.1.1.1 bdr:0.0.0.0 default-information originate To generate a default external route into an OSPF routing domain, configure Dell Networking Operating System (OS).
PAGE 1038
Related Commands Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. • redistribute — redistributes routes from other routing protocols into OSPF. default-metric Change the metrics of redistributed routes to a value useful to OSPF. Use this command with the redistribute command.
PAGE 1039
Version Description pre- 6.1.1.1 Introduced on the E-Series. description Add a description about the selected OSPF configuration. Syntax description description To remove the OSPF description, use the no description command. Parameters description Enter a text string description to identify the OSPF configuration (80 characters maximum). Defaults None Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1040
distance Define an administrative distance for particular routes to a specific IP address. Syntax distance weight [ip-address mask access-list-name] To delete the settings, use the no distance weight [ip-address mask access-list-name] command. Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110. ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address.
PAGE 1041
distance ospf Configure an OSPF distance metric for different types of routes. Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255. The default is 110.
PAGE 1042
Usage Information To specify a distance for routes learned from other routing domains, use the redistribute command. distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table. Syntax distribute-list prefix-list-name in [interface] To delete a filter, use the no distribute-list prefix-list-name in [interface] command. Parameters prefix-list-name Enter the name of a configured prefix list.
PAGE 1043
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter.
PAGE 1044
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1045
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on all platforms. The higher this parameter is set, the faster OSPF converge takes place. NOTE: The faster the convergence, the more frequent the route calculations and updates.
PAGE 1046
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. In OSPF, flooding is the most resource-consuming task. The flooding algorithm, described in RFC-2328, requires that OSPF flood LSAs (Link State Advertisements) on all interfaces, as governed by LSA’s flooding scope (see Section 13 of the RFC).
PAGE 1047
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. Added support for Multi-Process OSPF. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The Helper mode is enabled by default on the device.
PAGE 1048
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 7.8.1.0 Restart role enabled on the S-Series (Both Helper and Restart roles now supported on S-Series). Added support for Multi-Process OSPF. 7.7.1.0 Added Helper-Role support on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart mode Enable the graceful restart mode.
PAGE 1049
Version Description 7.8.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. graceful-restart role Specify the role for your OSPF router during graceful restart. Syntax graceful-restart role [helper-only | restart-only] To disable graceful restart role, use the no graceful-restart role command. Parameters role helper-only (OPTIONAL) Enter the keywords helper-only to specify the OSPF router is a helper only during graceful restart.
PAGE 1050
ip ospf auth-change-wait-time OSPF provides a grace period while OSPF changes its interface authentication type. During the grace period, OSPF sends out packets with new and old authentication scheme until the grace period expires. Syntax ip ospf auth-change-wait-time seconds To return to the default, use the no ip ospf auth-change-wait-time command. Parameters seconds Enter the seconds. The range is from 0 to 300. Defaults zero (0) seconds.
PAGE 1051
ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface. Syntax ip ospf authentication-key [encryption-type] key To delete an authentication key, use the no ip ospf authentication-key command. Parameters encryption-type (OPTIONAL) Enter 7 to encrypt the key. key Enter an eight-character string. Strings longer than eight characters are truncated. Defaults Not configured.
PAGE 1052
ip ospf cost Change the cost associated with the OSPF traffic on an interface. Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters cost Enter a number as the cost. The range is from 1 to 65535. Defaults The default cost is based on the reference bandwidth. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1053
ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds.
PAGE 1054
ip ospf hello-interval Specify the time interval between the hello packets sent on the interface. Syntax ip ospf hello-interval seconds To return to the default value, use the no ip ospf hello-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 10 seconds. Defaults 10 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1055
ip ospf message-digest-key Enable OSPF MD5 authentication and send an OSPF message digest key on the interface. Syntax ip ospf message-digest-key keyid md5 key To delete a key, use the no ip ospf message-digest-key keyid command. Parameters keyid Enter a number as the key ID. The range is from 1 to 255. key Enter a continuous character string as the password. Defaults No MD5 authentication is configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1056
After the reply is received and the new key is authenticated, delete the old key. Dell recommends keeping only one key per interface. NOTE: The MD5 secret is stored as plain text in the configuration file with service password encryption. Write down or otherwise record the key. You cannot learn the key once it is configured. Use caution when changing the key. ip ospf mtu-ignore Disable OSPF MTU mismatch detection upon receipt of database description (DBD) packets.
PAGE 1057
ip ospf network Set the network type for the interface. Syntax ip ospf network {broadcast | point-to-point} To return to the default, use the no ip ospf network command. Parameters broadcast Enter the keyword broadcast to designate the interface as part of a broadcast network. point-to-point Enter the keywords point-to-point to designate the interface as part of a point-topoint network. Defaults Broadcast. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1058
ip ospf priority To determine the designated router for the OSPF network, set the priority of the interface. Syntax ip ospf priority number To return to the default setting, use the no ip ospf priority command. Parameters number Enter a number as the priority. The range is from 0 to 255. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1059
ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies belonging to the interface. Syntax ip ospf retransmit-interval seconds To return to the default values, use the no ip ospf retransmit-interval command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 5 seconds.
PAGE 1060
ip ospf transmit-delay To send a link state update packet on the interface, set the estimated time elapsed. Syntax ip ospf transmit-delay seconds To return to the default value, use the no ip ospf transmit-delay command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 1 second. This value must be greater than the transmission and propagation delays for the interface.
PAGE 1061
log-adjacency-changes To send a Syslog message about changes in the OSPF adjacency state, set Dell Networking OS. Syntax log-adjacency-changes To disable the Syslog messages, use the no log-adjacency-changes command. Defaults Disabled. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1062
To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters number Specify the number of paths. The range for OSPFv2 is from 1 to 64. The default for OSPFv2 is 4 paths. The range for OSPFv3 is from 1 to 64. The default for OSPFv3 is 8 paths. Defaults 4 Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific.
PAGE 1063
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 1064
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1065
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 1066
• The previous no passive-interface interface is removed from the running configuration. • The ABR status for the router is updated. • Save passive-interface interface into the running configuration. passive-interface default • All present and future OSPF interfaces are marked as passive. • Any adjacency is explicitly terminated from all OSPF interfaces. • All previous passive-interface interface commands are removed from the running configuration.
PAGE 1067
metric-type typevalue (OPTIONAL) Enter the keywords metric-type then one of the following: • 1 = OSPF External type 1 • 2 = OSPF External type 2 route-map mapname (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag then a number. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1068
redistribute bgp Redistribute BGP routing information throughout the OSPF instance. Syntax redistribute bgp as number [metric metric-value] | [metric-type type-value] | [tag tag-value] To disable redistribution, use the no redistribute bgp as number [metric metric-value] | [metric-type type-value] [route-map map-name] [tag tag-value] command. Parameters as number Enter the autonomous system number. The range is from 1 to 65535.
PAGE 1069
Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the keyword default. pre- 6.1.1.1 Introduced on the E-Series. redistribute isis Redistribute IS-IS routing information throughout the OSPF instance.
PAGE 1070
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.
PAGE 1071
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information You can configure an arbitrary value in the IP address format for each router. However, each router ID must be unique.
PAGE 1072
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 1073
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1074
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added output for LSA throttling timers. 8.3.7.0 Introduced on the S4810. 7.9.1.0 Added support for VRF. 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1075
show ip ospf asbr Display all autonomous system boundary router (ASBR) routers visible to OSPF. Syntax Parameters Defaults Command Modes Command History Usage Information show ip ospf [process-id | vrf vrf-name] asbr process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1076
You can determine if an ASBR is in a directly connected area (or not) by the flags. For ASBRs in a directly connected area, E flags are set. In the following example, router 1.1.1.1 is in a directly connected area since the Flag is E/-/-/. For remote ASBRs, the E flag is clear (-/-/-/). Example Dell# show ip ospf 1asbr RouterID 3.3.3.3 1.1.1.1 Dell# Flags -/-/-/ E/-/-/ Cost Nexthop 2 10.0.0.2 0 0.0.0.0 Interface Area Te 1/1/1/1 1 0 show ip ospf database Display all LSA information.
PAGE 1077
Usage Information Example Version Description 7.8.1.0 Added support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database command shown in the following example. Field Description Link ID Identifies the router ID. ADV Router Identifies the advertising router’s ID. Age Displays the link state age. Seq# Identifies the link state sequence number.
PAGE 1078
show ip ospf database asbr-summary Display information about autonomous system (AS) boundary LSAs. Syntax show ip ospf [process-id] database asbr-summary [link-state-id] [adv-router ipaddress] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1079
Usage Information Example Version Description pre- 6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf database asbr-summary command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service.
PAGE 1080
Related Commands • show ip ospf database — display OSPF database information. show ip ospf database external Display information on the AS external (type 5) LSAs. Syntax show ip ospf [process-id | vrf vrf-name ] database external [link-state-id] [adv-router ip-address] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1081
Usage Information Example Version Description 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id database external command shown in the following example. Field Description LS Age Displays the LSA’s age. Options Displays the optional capabilities available on router.
PAGE 1082
Length: 36 Network Mask: /32 Metrics Type: 2 TOS: 0 Metrics: 25 Forward Address: 0.0.0.0 External Route Tag: 43 LS age: 1868 Options: (No TOS-capability, DC) LS type: Type-5 AS External Link State ID: 24.216.12.0 Advertising Router: 20.20.20.8 LS Seq Number: 0x80000005 Checksum: 0xa00e Length: 36 Network Mask: /24 Metrics Type: 2 TOS: 0 Metrics: 1 Forward Address: 0.0.0.0 External Route Tag: 701 Dell# Related Commands • show ip ospf database — display OSPF database information.
PAGE 1083
Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.
PAGE 1084
Options: (No TOS-capability, DC, E) LS type: Network Link State ID: 202.10.10.2 Advertising Router: 20.20.20.8 LS Seq Number: 0x80000006 Checksum: 0xa35 Length: 36 Network Mask: /24 Attached Router: 20.20.20.8 Attached Router: 20.20.20.9 Attached Router: 20.20.20.7 Network (Area 0.0.0.1) LS age: 252 Options: (TOS-capability, No DC, E) LS type: Network Link State ID: 192.10.10.2 Advertising Router: 192.10.10.2 LS Seq Number: 0x80000007 Checksum: 0x4309 Length: 36 Network Mask: /24 Attached Router: 192.10.10.
PAGE 1085
• Command History Related Commands EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1086
• adv-router ipaddress Command Modes Command History Usage Information 1086 • EXEC • EXEC Privilege the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1087
Example Item Description Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Opaque Type Displays the Opaque type field (the first 8 bits of the Link State ID). Opaque ID Displays the Opaque type-specific ID (the remaining 24 bits of the Link State ID). Dell> show ip ospf 1 database opaque-area OSPF Router with ID (3.3.3.
PAGE 1088
Command Modes Command History Related Commands • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1089
adv-router ipaddress Command Modes Command History Related Commands • EXEC • EXEC Privilege • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router then the IP address of an Advertising Router to display only the LSA information about that router. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1090
vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view the router LSA information corresponding to the OSPF process that is tied to a specific VRF. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1091
Item Example Description • DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. • E or No E is displayed on whether the originating router can accept AS External LSAs. LS Type Displays the LSA type. Link State ID Displays the Link State ID. Advertising Router Identifies the router ID of the LSA’s originating router. LS Seq Number Displays the link state sequence number. This number detects duplicate or old LSAs.
PAGE 1092
Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.141.2 (Link Data) Router Interface address: 192.68.141.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.140.2 (Link Data) Router Interface address: 192.68.140.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Stub Network (Link ID) Network/subnet number: 11.1.5.
PAGE 1093
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1094
Summary Network (Area 0.0.0.0) LS age: 1551 Options: (No TOS-capability, DC, E) LS type: Summary Network Link State ID: 192.68.16.0 Advertising Router: 192.168.17.1 LS Seq Number: 0x80000054 Checksum: 0xb5a2 Length: 28 Network Mask: /24 TOS: 0 Metric: 1 LS age: 9 Options: (No TOS-capability, No DC, E) LS type: Summary Network Link State ID: 192.68.32.0 Advertising Router: 1.1.1.
PAGE 1095
Command Modes Command History Usage Information • EXEC • EXEC Privilege • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1096
Example Item Description Process ID... This line displays the OSPF Process ID, Router ID, Network type and cost metric for this interface. Transmit Delay... This line displays the interface’s settings for Transmit Delay, State, and Priority. In the State setting, BDR is Backup Designated Router. Designated Router... This line displays the ID of the Designated Router and its interface address. Backup Designated... This line displays the ID of the Backup Designated Router and its interface address.
PAGE 1097
Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to show information corresponding to the OSPF neighbors that are tied to a specific VRF. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1098
20.20.20.1 Dell# 1 FULL/DROTHER00:00:36 192.10.10.4 Te 1/1/3/1 0.0.0.1 show ip ospf routes Display routes OSPF calculates and stores in OSPF RIB. Syntax show ip ospf [process-id | vrf vrf-name ] routes Parameters Defaults Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1099
This command has the following limitations: • The display output is sorted by prefixes; intra-area ECMP routes are not displayed together. • For Type 2 external routes, Type 1 cost is not displayed. NOTE: Starting with Version 9.4(0.0), the loopback IP address advertised to the neighbor is not displayed in the output because they are not accounted as inactive OSPF routes, whereas the loopback IP address is displayed until Dell Networking OS Version 9.3(0.0). Starting with Version 9.4(0.
PAGE 1100
neighbor router-id Defaults For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.). None Command Modes Command History Usage Information 1100 • • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1101
Row Heading Description TxQ-Len The transmission queue length. RxQ-Len The reception queue length. Tx-Mark The highest number mark in the transmission queue. Rx-Mark The highest number mark in the reception queue. Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets.
PAGE 1102
Error packets (Only for RX) Intf-Down Wrong-Len Auth-Err Version No-Buffer Q-OverFlow 0 0 0 0 0 0 Non-Dr Invld-Nbr MD5-Err AreaMis Seq-No Unkown-Pkt 0 0 0 0 0 0 Self-Org 0 Nbr-State 0 Chksum 0 Conf-Issues 0 Socket 0 Error packets (Only for TX) Socket Errors Dell# Usage Information Example (Statistics) 0 The show ip ospf process-id statistics command displays the error packet count received on each interface as: • The hello-timer remaining value for each interface • The wait-timer remaining value
PAGE 1103
show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire. Syntax Parameters Defaults Command Modes Command History Example show ip ospf [process-id] timers rate-limit process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1104
show ip ospf topology Display routers in directly connected areas. Syntax show ip ospf [process-id] topology Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. None Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1105
summary-address To advertise one external route, set the OSPF ASBR. Syntax summary-address ip-address mask [not-advertise] [tag tag-value] To disable summary address, use the no summary-address ip-address mask command. Parameters ip-address Specify the IP address in dotted decimal format of the address to summarize. mask Specify the mask in dotted decimal format of the address to summarize.
PAGE 1106
With the not-advertise parameter configured, you can use this command to filter out some external routes. For example, if you want to redistribute static routes to OSPF, but you don't want OSPF to advertise routes with prefix 1.1.0.0, you can configure the summary-address 1.1.0.0 255.255.0.0 not-advertise to filter out all the routes fall in range 1.1.0.0/16. Related Commands • area range — summarize routes within an area.
PAGE 1107
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. Usage Information Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage.
PAGE 1108
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1109
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. OSPFv3 Commands Open shortest path first version 3 (OSPFv3) for IPv6 is supported on the platform.
PAGE 1110
For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1111
area encryption Configure an IPsec encryption policy for OSPFv3 packets in an OSPFv3 area. Syntax Parameters area area-id encryption ipsec spi number esp encryption-algorithm [keyencryption-type] key authentication-algorithm [key-encryption-type] key area area-id Area for which OSPFv3 traffic is to be encrypted. For area-id, enter a number. The range is from 0 to 4294967295. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1112
For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). null Causes an encryption policy configured for the area to not be inherited on the interface. Defaults Not configured. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1113
auto-cost Specify how the OSPF interface cost is calculated based on the reference bandwidth method. Syntax auto-cost [reference-bandwidth ref-bw] To return to the default bandwidth or to assign cost based on the interface type, use the no auto-cost [reference-bandwidth ref-bw] command. Parameters ref-bw (OPTIONAL) Specify a reference bandwidth in megabits per second. The range is from 1 to 4294967. The default is 100 megabits per second. Defaults 100 megabits per second.
PAGE 1114
Parameters Command Modes Command History vrf vrf-name • EXEC • EXEC Privilege (Optional) Enter the keyword vrf followed by the name of the VRF to clear IPv6 routes corresponding to that VRF. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1115
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the S4820T, S4810, and Z9000.
PAGE 1116
debug ipv6 ospf packet Display debug information and interface types on OSPF IPv6 packets. Syntax debug ipv6 ospf {packet | events} [interface] Parameters interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1117
07:21:40 : OSPFv3: Received, Ver:3, Type:1(Hello), Len:40, Router ID: 223.255.255.254, Area ID:0, Chksum:af8f, Inst:0, from Te 1/1/6/1 Dell# Command Fields Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1118
route-map mapname (OPTIONAL) Enter the keywords route-map then the name of an established route map. Defaults Disabled. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1119
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. By default, OSPFv3 graceful restart is disabled and functions only in a helper role to help restarting neighbor routers in their graceful restarts when it receives a Grace LSA.
PAGE 1120
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. OSPFv3 graceful restart supports planned-only and/or unplanned-only restarts. The default is support for both planned and unplanned restarts.
PAGE 1121
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.4.1.0 Introduced on the E-Series and C-Series. ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface.
PAGE 1122
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Before you enable IPsec authentication on an OSPFv3 interface, first enable IPv6 unicast routing globally, configure an IPv6 address and enable OSPFv3 on the interface, and assign the interface to an area.
PAGE 1123
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1124
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. By default, the dead interval is four times longer than the default hello-interval. • ipv6 ospf hello-interval – specify the time interval between hello packets.
PAGE 1125
key-encryptiontype (OPTIONAL) Specifies if the authentication key is encrypted. Valid values: 0 (key is not encrypted) or 7 (key is encrypted). key Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1126
ipv6 ospf graceful-restart helper-reject Configure an OSPFv3 interface to not act upon the Grace LSAs that it receives from a restarting OSPFv3 neighbor. Syntax ipv6 ospf graceful-restart helper-reject To disable the helper-reject role, enter no ipv6 ospf graceful-restart helper-reject. Defaults The helper-reject role is not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1127
To return to the default time interval, enter no ipv6 ospf hello—interval. Parameters seconds Enter the time interval in seconds as the time between hello packets. The range is from 1 to 65525 seconds. Defaults 10 seconds (Ethernet). Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.
PAGE 1128
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.
PAGE 1129
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. maximum-paths Enable the software to forward packets over multiple paths. Syntax maximum-paths number To disable packet forwarding over multiple paths, use the no maximum-paths command. Parameters number Specify the number of paths.
PAGE 1130
max-metric router-lsa Configure the maximum cost of 65535 on a new router so that it functions as a stub router in the network and OSPF traffic destined to other networks is not forwarded on a path through the router.
PAGE 1131
through the new router, other routers will not use a path through the router as a transit path to forward traffic to other networks. Use the max-metric router-lsa command to gracefully shut down or reload a router without dropping packets destined for other networks. NOTE: If you enter the max-metric router-lsa command without an option (on-startup announce-time or on-startup wait-for-bgp [wait-time]), the maximum metric of 65535 is always announced in LSAs sent by the router.
PAGE 1132
To enable sending routing updates on an interface, use the no passive-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1133
On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute into OSPFv3. Syntax redistribute {bgp as number}{connected | static}[metric metric-value | metrictype type-value] [route-map map-name] [tag tag-value] To disable redistribution, use the no redistribute {connected | static} command.
PAGE 1134
Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.
PAGE 1135
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. You can configure an arbitrary value in the IP address for each router.
PAGE 1136
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. The show crypto ipsec policy command output displays the AH and ESP parameters configured in IPsec security policies, including the SPI number, keys, and algorithms used. When configured in a helper-reject role, an OSPFv3 router ignores the Grace LSAs that it receives from a restarting OSPFv3 neighbor.
PAGE 1137
Field Description Inbound ESP SPI and Outbound ESP SPI The encapsulating security payload (ESP) security policy index (SPI) for inbound and outbound links. Inbound ESP Auth Key and Outbound Auth Key The ESP authentication key for inbound and outbound links. Inbound ESP Cipher Key and Outbound ESP Cipher Key The ESP encryption key for inbound and outbound links. Transform set The set of security protocols and algorithms used in the policy.
PAGE 1138
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1139
replay detection support : N STATUS : ACTIVE outbound esp sas spi : 600 (0x258) transform : esp-des esp-sha1-hmac in use settings : {Transport, } replay detection support : N STATUS : ACTIVE show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/outbound ah Authentication policy applied to inbound or outbound traffic.
PAGE 1140
database-summary (OPTIONAL) Enter the keywords database-summary to view a summary of database LSA information. grace-lsa (OPTIONAL): Enter the keywords grace-lsa to display the Type-11 Grace LSAs sent and received on an OSPFv3 router. Defaults None Command Modes EXEC EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1141
Example (databasesummary) Dell# show ipv6 ospf 3 database database-summary OSPFv3 Router with ID (1.1.1.
PAGE 1142
vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed. interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1143
NetworkType BROADCAST, Cost: 1, Passive: No Transmit Delay is 100 sec, State DR, Priority 1 Interface is using OSPF global mode BFD configuration. Designated router on this network is 11.1.1.1 (local) No backup designated router on this network Timer intervals configured, Hello 10, Dead 40, Wait 1, Retransmit 5 Dell# show ipv6 ospf neighbor Display the OSPF neighbor information on a per-interface basis.
PAGE 1144
Example Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. Dell# show ipv6 ospf 3 neighbor te 1/1/2/1 Neighbor ID 63.114.8.
PAGE 1145
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11.0.0 Introduced the keyword msec. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S6000-ON, S6000, S4820T, S4810, S5000.
PAGE 1146
37 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell Networking OS.
PAGE 1147
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.7.1.0 Introduced on the E-Series. • ip redirect-list – enable an IP Redirect List.
PAGE 1148
Usage Information Version Description 7.7.1.0 Introduced on the E-Series. You can apply any number of redirect-groups to an interface. A redirect list can contain any number of configured rules. These rules includes the next-hop IP address where the incoming traffic is to be redirected. If the next hop address is reachable, traffic is forwarded to the specified next hop. Otherwise, the normal routing table is used to forward traffic.
PAGE 1149
Version Description 6.5.3.0 Introduced on the E-Series. permit Configure a permit rule. A permit rule excludes the matching packets from PBR classification and routes them using conventional routing. Syntax permit {ip-protocol-number | protocol-type} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [bit] [operators] To remove the rule, use one of the following: Parameters • If you know the filter sequence number, use the no seq sequence-number syntax command.
PAGE 1150
• neq = not equal to • gt = greater than • lt= less than • range = inclusive range of ports (you must specify two ports for the portcommand parameter.) Defaults None Command Modes REDIRECT-LIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1151
slot/port Enter the keyword slot / port followed by the slot/port information. tunnel Enter the keyword tunnel to configure the tunnel setting. tunnel-id Enter the keyword tunnel-id to redirect the traffic. track Enter the keyword track to enable the tracking. track Enter the keyword track to track object-id. ip-protocol-number Enter a number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1152
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, and Z9000. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.0 Introduced on the E-Series. 7.7.1.
PAGE 1153
• ip for any internet protocol • tcp for transmission control protocol • udp for user datagram protocol source Enter the IP address of the network or host from which the packets were sent. mask Enter a network mask in /prefix format (/x). any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then the IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1154
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, S6000-ON, and Z9000. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. show cam pbr Display the PBR CAM content.
PAGE 1155
00004 5 Dell# Related Commands N/A IP 0x0 0 0 0.0.0.0/0 0.0.0.0/0 00:01:e8:8a:fd:76 Vl 1020(Po 100) • ip redirect-group – applies a redirect group to an interface. • show ip redirect-list – displays the redirect-list configuration. show ip redirect-list View the redirect list configuration and the interfaces it is applied to.
PAGE 1156
38 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement.
PAGE 1157
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. The existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1158
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. If you use this command on a local VLT node, all multicast routes from the local PIM TIB, the entire multicast route table, and all the entries in the data plane are deleted. The local VLT node sends a request to the peer VLT node to download multicast routes learned by the peer. Both local and synced routes are removed from the local VLT node multicast route table. The peer VLT node clears synced routes from the node.
PAGE 1159
• register: to view the register suppression timer Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1160
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. This command is applied to the subsequent PIM-BSR. Existing BSR advertisements are cleaned up by time-out. To clean the candidate RP advertisements, use the clear ip pim rp-mapping command. ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router.
PAGE 1161
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1162
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series on port-channels and the S-Series. The router with the largest value assigned to an interface becomes the designated router. If two interfaces contain the same designated router priority value, the interface with the largest interface IP address becomes the designated router.
PAGE 1163
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. 7.7.1.0 Introduced on the E-Series. Usage Information When you configure a join filter, it is applicable for both ingress and egress flows. There is no option to specify in or out parameters while configuring a join filter.
PAGE 1164
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series.
PAGE 1165
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. Syntax ip pim [vrf vrf-name] register-filter access-list To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command.
PAGE 1166
Usage Information The access name is an extended IP access list that denies PIM register packets to RP at the source DR based on the multicast and group addresses. Do not enter this command before creating the access-list. ip pim rp-address Configure a static PIM rendezvous point (RP) address for a group or access-list.
PAGE 1167
Usage Information Version Description 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. pre- 6.1.1.1 Introduced on the E-Series. First-hop routers use this address by to send register packets on behalf of source multicast hosts. The RP addresses are stored in the order in which they are entered. The RP is chosen based on a longer prefix match for a group. The RP selection does not depend on dynamic or static RP assignments.
PAGE 1168
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the acl-name parameter. 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1169
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. The interface must be enabled (the no shutdown command) and not have the switchport command configured. Multicast must also be enabled globally (using the ip multicast-lag-hashing command). PIM is supported on the port-channel interface.
PAGE 1170
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Series. 7.7.1.1 Introduced This command configures an expiration timer for all S.G entries, unless they are assigned to an Extended ACL.
PAGE 1171
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Dell Networking OS supports standard access lists for the SSM range. You cannot use extended ACLs for configuring the SSM range.
PAGE 1172
NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. infinity (OPTIONAL) Enter the keyword infinity to never switch to the source-tree. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.
PAGE 1173
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series.
PAGE 1174
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.
PAGE 1175
show ip pim neighbor View PIM neighbors. Syntax Parameters show ip pim [vrf vrf-name] neighbor vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes Command History Usage Information • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1176
Field Description Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires). Ver Displays the PIM version number. • DR prio/Mode Example v2 = PIM version 2 Displays the Designated Router priority and the mode.
PAGE 1177
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the S-Series. Example Dell# show ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.4 224.3.3.3 165.87.20.4 225.1.2.1 165.87.
PAGE 1178
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1179
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for VRF. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.1 Support for the display of PIM-SM snooping status was added on E-Series. 8.1.1.
PAGE 1180
show ip pim tib View the PIM tree information base (TIB). Syntax show ip pim [vrf vrf-name] tib [group-address [source-address]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. Command Modes Command History Usage Information 1180 group-address (OPTIONAL) Enter the group address in dotted decimal format (A.B.C.D).
PAGE 1181
Example Field Description expires Displays the amount of time until the entry expires and is removed from the database. RP Displays the IP address of the RP/source for this entry.
PAGE 1182
39 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). • The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1183
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 1184
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S6000, Z9500, S6000-ON. show running-config monitor session — displays information about monitor configurations. monitor session Create a session for monitoring traffic with port monitoring.
PAGE 1185
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(2.0) Introduced on the S3100 series. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the drop parameter. 9.7(0.0) Introduced on the S6000-ON. Introduced the set ip dscp and set ip ttl parameters. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 9.0.2.0 Introduced on the S6000. 9.0.2.
PAGE 1186
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000-ON, Z9500. • monitor session — enable a monitoring session. • show monitor session — display the monitor session. show config Display the current monitor session configuration.
PAGE 1187
show monitor session Display information about monitoring sessions. Syntax show monitor session {session-ID} To display monitoring information for all sessions, use the show monitor session command. Parameters Defaults Command Modes Command History Example session-ID (OPTIONAL) Enter a session identification number. The range is from 0 to 65535. none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1188
IP DSCP TTL ------ ---------------1 Te 1/1/2/1 0.0.0.0 0 Dell# Related Commands Drop Rate Gre-Protocol FcMonitor ------------- ---- -------------- -------------- --------remote-ip rx Port 0.0.0.0 0 No N/A N/A yes • monitor session — creates a monitoring session. • rate-limit — configures the rate-limit. show running-config monitor session Display the running configuration of all monitor sessions or a specific session.
PAGE 1189
Usage Information The monitoring command is saved in the running configuration at the Monitor Session mode level and can be restored after a chassis reload. Example Dell# show running-config monitor session ! monitor session 1 source TenGigabitEthernet 1/1/1/1 destination TenGigabitEthernet 1/1/2/1 direction rx ! monitor multicast-queue 7 Dell# Related Commands • monitor session — creates a monitoring session. • show monitor session — displays a monitoring session.
PAGE 1190
interface direction {rx | tx | both} • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a port channel interface, enter the keywords port-channel then a number.
PAGE 1191
Example Version Description 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1192
40 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell Networking OS is supported on the platforms. Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell Networking OS private VLAN implementation is based on RFC 3069. For more information, see the following commands.
PAGE 1193
• A trunk port can also belong to a regular VLAN (non-private VLAN). Topics: • ip local-proxy-arp • private-vlan mode • private-vlan mapping secondary-vlan • switchport mode private-vlan ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN. Syntax [no] ip local-proxy-arp To disable Layer 3 communication between secondary VLANs in a private VLAN, use the no ip local-proxyarp command in INTERFACE VLAN mode for the primary VLAN.
PAGE 1194
Related Commands • private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. • private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN. • show arp — displays the ARP table. • switchport mode private-vlan — sets PVLAN mode of the selected port. private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary.
PAGE 1195
• mode to community or isolated even before associating it to a primary VLAN. This secondary VLAN continues to work normally as a normal VLAN even though it is not associated to a primary VLAN. (A syslog message indicates this.) • must not have a port in it when VLAN mode is being set. Only ports (and port channels) configured as promiscuous, host, or PVLAN trunk ports (as previously described) can be added to the PVLAN. No other regular ports can be added to the PVLAN.
PAGE 1196
Usage Information Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. The list of secondary VLANs can be: • Specified in comma-delimited or hyphenated-range format. • Specified with this command even before they have been created. • Amended by specifying the new secondary VLAN to be added to the list. • private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary.
PAGE 1197
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information The assignment of the various PVLAN port types to port and port channel (LAG) interfaces is shown in the following example.
PAGE 1198
41 Per-VLAN Spanning Tree Plus (PVST+) The Dell Networking OS implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell Networking OS supports PVST+ on the platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line.
PAGE 1199
Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.1 Introduced.
PAGE 1200
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. • protocol spanning-tree pvst — enter PVST+ mode. extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID.
PAGE 1201
We are the root of Vlan 5 Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ------------------------------------------------------------Te 1/1/1/1 128.140 128 200000 FWD 0 32773 0001.e832.73f7 128.140 Te 1/1/2/1 128.142 128 200000 DIS 0 32773 0001.e832.73f7 128.142 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge -------------------------------------------------------Te 1/1/1/1 Desg 128.
PAGE 1202
Version Description 8.3.1.0 Introduced. Example Dell# conf Dell(conf)# protocol spanning-tree pvst Dell(conf-pvst)# no disable Dell(conf-pvst)# vlan 2 bridge-priority 4096 Dell(conf-pvst)# vlan 3 bridge-priority 16384 Dell(conf-pvst)# Dell(conf-pvst)# show config ! protocol spanning-tree pvst no disable vlan 2 bridge-priority 4096 vlan 3 bridge-priority 16384 Dell# Usage Information After you enable PVST+, the device runs an STP instance for each VLAN it supports.
PAGE 1203
Defaults Command Modes Command History Usage Information Example (Brief) none • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1204
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------------------------------------------------------Te 1/1/1/1 128.130 128 20000 FWD 20000 4096 0001.e801.6aa8 Te 1/1/2/1 128.131 128 20000 BLK 20000 4096 0001.e801.6aa8 Te 1/1/3/1 128.146 128 20000 FWD 20000 16384 0001.e805.e306 Te 1/1/4/1 128.147 128 20000 FWD 20000 16384 0001.e805.e306 128.426 128.427 128.146 128.
PAGE 1205
Bpdu guard :disable (default) Bpdus sent 152, received 27562 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ----------------------------------------------------------Te 1/1/1/1 128.1223 128 20000 EDS 0 32768 0001.e800.a12b 128.
PAGE 1206
vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. cost number Enter the keyword cost then the port cost value. The range is from 1 to 200000. Defaults: • 100 Mb/s Ethernet interface = 200000. • 1-Gigabit Ethernet interface = 20000. • 10-Gigabit Ethernet interface = 2000. • Port Channel interface with one 100 Mb/s Ethernet = 200000. • Port Channel interface with one 1 Gigabit Ethernet = 20000. • Port Channel interface with one 10 Gigabit Ethernet = 2000.
PAGE 1207
Usage Information Version Description 7.4.1.0 Added the optional Bridge Port Data Unit (BPDU) guard. 6.2.1.1 Introduced. The BPDU guard option prevents the port from participating in an active STP topology in case a BPDU appears on a port unintentionally, or is misconfigured, or is subject to a DOS attack. This option places the port into the Error Disable state if a BPDU appears, and a message is logged so that the administrator can take corrective action.
PAGE 1208
spanning-tree pvst err-disable Place ports in an Err-Disabled state if they receive a PVST+ BPDU when they are members an untagged VLAN. Syntax spanning-tree pvst err-disable cause invalid-pvst-bpdu Defaults Enabled; ports are placed in the Err-Disabled state if they receive a PVST+ BPDU when they are members of an untagged VLAN. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1209
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1210
To return to the default value, use the no vlan bridge-priority command. Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. bridge-priority value Enter the keywords bridge-priority then the bridge priority value in increments of 4096. The range is from 0 to 61440. The default is 32768. Defaults 32768 Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1211
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. forward-delay seconds Enter the keywords forward-delay then the time interval, in seconds, that Dell Networking OS waits before transitioning PVST+ to the forwarding state. The range is from 4 to 30 seconds. The default is 15 seconds. Defaults 15 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific.
PAGE 1212
Parameters vlan vlan-range Enter the keyword vlan then the VLAN numbers. The range is from 1 to 4094. hello-time seconds Enter the keywords hello-time then the time interval, in seconds, between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. Defaults 2 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1213
max-age seconds Enter the keywords max-age then the time interval, in seconds, that Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40 seconds. The default is 20 seconds. Defaults 20 seconds Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 1214
42 Quality of Service (QoS) The Dell Networking OS commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking products. platform. Topics: • Global Configuration Commands • Per-Port QoS Commands • Policy-Based QoS Commands • DSCP Color Map Commands Global Configuration Commands There is only one global configuration QoS command.
PAGE 1215
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced. By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations.
PAGE 1216
service-class dot1p-mapping Configure a service-class criterion based on a dot1p value. Syntax service-class dot1p-mapping {dot1p0 queue | dot1p1 queue | dot1p2 queue | dot1p3 queue | dot1p4 queue| dot1p5 queue | dot1p6 queue | dot1p7 queue} Parameters Defaults queue Enter a value from 0 to 7. For each dot1p Priority, the default CoS queue value is: • Dot1p Priority : 0 1 2 3 4 5 6 7 • Queue : 1 0 2 3 4 5 6 7 Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1217
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1218
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The dot1p-priority command changes the priority of incoming traffic on the interface.
PAGE 1219
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.
PAGE 1220
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1221
Command Modes Command History Usage Information dot1p Queue ID 0 1 1 0 2 2 3 3 4 4 5 5 6 6 7 7 • INTERFACE • CONFIGURATION This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1222
You can apply this command on both physical interfaces and port channels. When you set the service-class dynamic for a port channel, the physical interfaces assigned to the port channel are automatically configured; you cannot assign the service-class dynamic command to individual interfaces in a port channel. • All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally.
PAGE 1223
Usage Information Related Commands Version Description 6.2.1.1 Introduced on the E-Series. The unit of bandwidth percentage is 1%. If the sum of the bandwidth percentages given to all eight classes exceeds 100%, the bandwidth percentage automatically scales down to 100%. • qos-policy-output — creates a QoS output policy. buffer-stats-snapshot Enable the buffer statistics tracking utility and enter the Buffer Statistics Snapshot configuration mode.
PAGE 1224
class-map Create/access a class map. Class maps differentiate traffic so that you can apply separate quality-of-service policies to each class. Syntax class-map {match-all | match-any} class-map-name [cpu-qos] [layer2] Parameters match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class.
PAGE 1225
Usage Information Version Description 7.4.1.0 E-Series Only: Expanded to add support for Layer 2. Packets arriving at the input interface are checked against the match criteria and configured using this command to determine if the packet belongs to that class. This command accesses CLASS-MAP mode, where the configuration commands include thematch ip and match mac options. When you create a class map to filter protocol traffic for CoPP, you must enter the keyword cpu-qos .
PAGE 1226
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.18.0 Introduced on the S4820T.
PAGE 1227
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 7.7.1.0 Introduced. • policy-map-input — creates an input policy map. • policy-map-output — creates an output policy map.
PAGE 1228
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.
PAGE 1229
set-ip-dscp value (OPTIONAL) Enter the keywords set-ip-dscp then the IP DSCP value. The matched traffic is marked with the DSCP value. The range is from 0 to 63. Defaults none Command Modes CLASS-MAP CONFIGURATION (config-class-map) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1230
match ip precedence Use IP precedence values as a match criteria. Syntax match {ip | ipv6 | ip-any} precedence ip-precedence-list [set-ip-dscp value] To remove IP precedence as a match criteria, use the no match {ip | ipv6 | ip-any} precedence ip-precedence-list [[multicast] set-ip-dscp value] command. Parameters ip Enter the keyword ip to support IPv4 traffic. ipv6 Enter the keyword ipv6 to support IPv6 traffic. ip-any Enter the keyword ip-any to support IPv4 and IPv6 traffic.
PAGE 1231
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Added support for the DSCP Marking option. 6.1.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip precedence command and the match ip dscp command are mutually exclusive. Up to eight precedence values can be matched in one match statement.
PAGE 1232
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Available on the C-Series and S-Series. 7.5.1.0 Added support for the DSCP Marking option. 7.4.1.0 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. • class-map — identifies the class map.
PAGE 1233
Usage Information Related Commands Version Description 7.4.1.0 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. • class-map — identifies the class map. match mac vlan Configure a match criterion for a class map based on VLAN ID. Syntax Parameters match mac vlan number number Enter the VLAN ID. The range is from 1 to 4094.
PAGE 1234
policy-aggregate Allow an aggregate method of configuring per-port QoS via policy maps. An aggregate QoS policy is part of the policy map (output) applied on an interface. Syntax policy-aggregate qos-policy-name To remove a policy aggregate configuration, use the no policy-aggregate qos-policy-name command. Parameters qos-policy-name Enter the name of the policy map in character format (32 characters maximum).
PAGE 1235
policy-map-input Create an input policy map. Syntax policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] To remove an input policy map, use the no policy-map-input policy-map-name cpu-qos | [layer2] [cpu-qos] command. Parameters policy-map-name Enter the name of the policy map in character format (32 characters maximum). cpu-qos Enter the cpu-qos keyword to assign this ACL to control plane traffic only. layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map.
PAGE 1236
Usage Information Related Commands The input policy map is used to classify incoming traffic to different flows using class-map, QoS policy, or incoming packets DSCP. This command enables Policy-Map-Input Configuration mode (conf-policy-map-in). When you configure an input policy map for CoPP, you must enter the keyword cpu-qos . • service-queue — assigns a class map and QoS policy to different queues. • service-policy input — applies an input policy map to the selected interface.
PAGE 1237
Related Commands • service-queue — assigns a class map and QoS policy to different queues. • policy-aggregate — allows an aggregate method of configuring per-port QoS using policy maps. • service-policy output — applies an output policy map to the selected interface. qos-policy-input Create a QoS input policy on the router.
PAGE 1238
Usage Information Version Description 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy. Once input policy is specified, rate-police can be defined. This command enables the qos-policy-input configuration mode— (conf-qos-policy-in). When changing a Service-Queue configuration in a QoS policy map, all QoS rules are deleted and re-added automatically to ensure that the order of the rules is maintained.
PAGE 1239
Usage Information Related Commands Version Description 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the output QoS policy. Once output policy is specified, rate-shape, scheduler strict, bandwidth-percentage, and WRED can be defined. This command enables the qos-policy-output configuration mode—(conf-qos-policy-out).
PAGE 1240
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. The default burst size is 100Kb.
PAGE 1241
Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added the kbps option on the C-Series, E-Series, and S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.
PAGE 1242
layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Defaults Layer 3 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1243
To remove the output policy map from the interface, use the no service-policy output policy-mapname command. Parameters policy-map-name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1244
class-map classmap-name (OPTIONAL) Enter the keyword class-map then the class map name assigned to the queue in character format (32 character maximum). NOTE: This option is available under policy-map-input only. qos-policy qospolicy-name (OPTIONAL) Enter the keywords qos-policy then the QoS policy name assigned to the queue in text format (32 characters maximum). This specifies the input QoS policy assigned to the queue under policy-map-input and output QoS policy under policy-map-output context.
PAGE 1245
set Mark outgoing traffic with a differentiated service code point (DSCP) or dot1p value. Syntax Parameters set {ip-dscp value | mac-dot1p value} ip-dscp value (OPTIONAL) Enter the keywords ip-dscp then the IP DSCP value. The range is from 0 to 63. mac-dot1p value Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7. Defaults none Command Modes CONFIGURATION (conf-qos-policy-in) Command History This guide is platform-specific.
PAGE 1246
show qos class-map View the current class map information. Syntax show qos class-map [class-name] Parameters Defaults class-name (Optional) Enter the name of a configured class map. none Command Modes Command History Example • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON.
PAGE 1247
show qos policy-map View the QoS policy map information. Syntax Parameters show qos policy-map {summary [interface] | detail} 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1248
Example (IPv4) Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series only: Added trust IPv6 diffserv . 6.2.1.
PAGE 1249
show qos policy-map-input View the input QoS policy map details. Syntax Parameters Defaults Command Modes Command History Example show qos policy-map-input [policy-map-name] [class class-map-name] [qos-policyinput qos-policy-name] policy-map-name Enter the policy map name. class class-mapname Enter the keyword class then the class map name. qos-policy-input qos-policy-name Enter the keyword qos-policy-input then the QoS policy name.
PAGE 1250
Aggregate Qos-policy-name AggPolicyIn Queue# Class-map-name Qos-policy-name 0 ClassMap1 qosPolicyInput Dell# Example Dell# show qos policy-map-input Policy-map-input pmap1 Trust ipv6-diffserv Queue# Class-map-name 0 c0 1 c1 2 c2 3 c3 4 c4 5 c5 6 c6 7 c7 Dell# Qos-policy-name q0 q1 q2 q3 q4 q6 q7 show qos policy-map-output View the output QoS policy map details. Syntax show qos policy-map-output [policy-map-name] [qos-policy-output qos-policyname] Parameters Defaults Enter the policy map name.
PAGE 1251
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Dell# show qos policy-map-output Policy-map-output PolicyMapOutput Aggregate Qos-policy-name AggPolicyOut Queue# Qos-policy-name 0 qosPolicyOutput Dell# show qos qos-policy-input View the input QoS policy details.
PAGE 1252
Example Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Dell# show qos qos-policy-input Qos-policy-input QosInput Rate-police 100 50 peak 100 50 Dscp 32 Dell# show qos qos-policy-output View the output QoS policy details. Syntax show qos qos-policy-output [qos-policy-name] Parameters Defaults Enter the QoS policy name.
PAGE 1253
Example Version Description 6.1.1.1 Introduced on the E-Series. Dell# show qos qos-policy-output Qos-policy-output qosOut Rate-limit 50 50 peak 50 50 Wred yellow 1 Wred green 1 Dell# show qos statistics View QoS statistics.
PAGE 1254
Defaults For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 1255
9 10 11 12 13 14 15 16 17 18 19 Dell# Usage Information UCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST MCAST 1132 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 143063 0 0 0 0 0 0 0 0 0 0 217 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 In a dual homing setup, you can use this command only from the primary VLT peer.
PAGE 1256
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. Example service-class buffer shared-threshold-weight Create a service class and associate the threshold weight of the shared buffer with each of the queues per port in the egress direction.
PAGE 1257
sharedthresholdweight on the queue % of available shared buffer that can be consumed by the queue 0 No dynamic sharing; shared buffer = 0. 1 0.77% 2 1.54% 3 3.03% 4 5.88% 5 11.11% 6 20% 7 33.33% 8 50% 9 66.67% 10 80% 11 88.89% Example test cam-usage Check the Input Policy Map configuration for the CAM usage. Syntax Parameters test cam-usage service-policy input policy-map stack-unit {[number port-set portpipe number] | [all]} policy-map Enter the policy map name.
PAGE 1258
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. This feature allows you to determine if the CAM has enough space available before applying the configuration on an interface.
PAGE 1259
threshold Specify the minimum and maximum threshold values for the configured WRED profiles. Syntax threshold min number max number max-drop-drop To remove the threshold values, use the no threshold min number max number command. Parameters min number Enter the keyword min then the minimum threshold number for the WRED profile. The range is from 1 to 9360. max number Enter the keyword max then the maximum threshold number for the WRED profile. The range is from 1 to 9360 KB.
PAGE 1260
trust Specify dynamic classification (DSCP) or dot1p to trust. Syntax trust {diffserv [fallback]| dot1p [fallback]} Parameters diffserv Enter the keyword diffserv to specify trust of DSCP markings. dot1p Enter the keyword dot1p to specify trust dot1p configuration. fallback Enter the keyword fallback to classify packets according to their DSCP or dot1p value as a secondary option in case no match occurs against the configured class maps.
PAGE 1261
Dynamic mapping honors packets marked according to the standard definitions of DSCP. The following lists the default mapping. Table 2.
PAGE 1262
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1263
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820t. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. When you enable wred ecn, and the number of packets in the queue is below the minimum threshold, packets are transmitted per the usual WRED treatment.
PAGE 1264
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3.0.0 Introduced on the S6000 and Z9000 platforms Usage Information If the average queue size is more than the maximum threshold of WRED, the packet is dropped. If the average queue size is between the minimum and maximum threshold values, the decision to drop or queue the packet is taken based on the packet drop probability.
PAGE 1265
Usage Information Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. Use the default pre-defined profiles or configure your own profile. You cannot delete the pre-defined profiles or their default values. This command enables WRED configuration mode —(conf-wred).
PAGE 1266
kbps Enter the keyword kbps to specify the peak rate limit in Kilobits per second (Kbps). Specify this value as a multiple of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps). pps Enter the keyword pps to specify the peak rate limit in packets per second (pps). The range is from 1 to 268000000. The default granularity is Megabits per second (Mbps). peak-rate Define the peak rate, which is the guaranteed or minimum confirmed rate for the packets.
PAGE 1267
Dell(conf-qos-policy-in)#rate-police 100 25 peak 80 500 % Error: Peak rate cannot be less than committed rate. service-pool wred A global buffer pool that is a shared buffer pool accessed by multiple queues when the minimum guaranteed buffers for the queue are consumed can be configured on the S6000 and Z9000 platforms. Create a global buffer pool that is a shared buffer pool accessed by multiple queues when the minimum guaranteed buffers for the queue are consumed.
PAGE 1268
Example Dell(conf-wred) #wred thresh-1 Dell(conf-wred) #threshold min 100 max 200 max-drop-rate 40 Dell(conf-wred) #wred thresh-2 Dell(conf-wred) #threshold min 300 max 400 max-drop-rate 80 Dell(conf) #service-pool wred green pool0 thresh-1 pool1 thresh-2 DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red.
PAGE 1269
Usage Information If the specified color-map does not exist, the Diffserv Manager (DSM) creates a color map and sets all the DSCP values to green (low drop precedence). The default setting for each DSCP value (0-63) is green (low drop precedence). This command allows setting the number of specific DSCP values to yellow or red. Important Points to Remember Example Related Commands • All DSCP values that are not specified as yellow or red are colored green.
PAGE 1270
you do, all the DSCP values are set to green (low drop precedence). To delete the DSCP color map that is being used by one or more interfaces, remove the DSCP map from each interface. Example Dell(conf)#qos dscp-color-map mymap Related Commands • qos dscp-color-map— associates the DSCP color map profile with an interface so that all IP packets received on it is given a color based on that color map. • dscp— sets the number of specific DSCP values for color map profile to yellow or red.
PAGE 1271
show qos dscp-color-policy Display DSCP color policy configuration for one or all interfaces. Syntax Parameters show qos dscp-color-policy {summary [interface] | detail {interface}} summary Enter the summary keyword to display summary information about a color policy on one or more interfaces. Detail Enter the detail keyword to display detailed information about a color policy on one or more interfaces. interface Enter the name of the interface that has color policy configured.
PAGE 1272
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps. Dell# show qos dscp-color-map Dscp-color-map mapONE yellow 4,7 red 20,30 Dscp-color-map mapTWO yellow 16,55 Display a specific DSCP color map.
PAGE 1273
43 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking OS supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2) on the platform. The Dell Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, see the Dell Networking OS Configuration Guide.
PAGE 1274
auto-summary Restore the default behavior of automatic summarization of subnet routes into network routes. This command applies only to RIP version 2. Syntax auto-summary To send sub-prefix routing information, use the no auto-summary command. Defaults Enabled. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1275
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.
PAGE 1276
database (OPTIONAL) Enter the keyword database to display messages when there is a change to the RIP database. events (OPTIONAL) Enter the keyword events to debug only RIP protocol changes. trigger (OPTIONAL) Enter the keyword trigger to debug only RIP trigger extensions. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1277
route-map mapname (OPTIONAL) Enter the keywords route-map then the name of a configured route-map. Defaults Disabled. Metric: 1. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1278
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1279
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 7.7.1.0 Introduced on the E-Series. • router rip — enters ROUTER mode on the switch.
PAGE 1280
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1281
Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.29.
PAGE 1282
• For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a Port Channel interface, enter the keywords port-channel then a number. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. connected (OPTIONAL) Enter the keyword connected to filter only directly connected routes.
PAGE 1283
ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.
PAGE 1284
ip rip receive version To receive specific versions of RIP, set the interface. The RIP version you set on the interface overrides the version command in ROUTER RIP mode. Syntax ip rip receive version [1] [2] To return to the default, use the no ip rip receive version command. Parameters 1 (OPTIONAL) Enter the number 1 for RIP version 1. 2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1285
ip rip send version To send a specific version of RIP, set the interface. The version you set on the interface overrides the version command in ROUTER RIP mode. Syntax ip rip send version [1] [2] To return to the default value, use the no ip rip send version command. Parameters 1 (OPTIONAL) Enter the number 1 for RIP version 1. The default is RIP version 1. 2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1286
ip split-horizon Enable split-horizon for RIP data on the interface. As described in RFC 2453, the split-horizon scheme prevents any routes learned over a specific interface to be sent back out that interface. Syntax ip split-horizon To disable split-horizon, use the no ip split-horizon command. Defaults Enabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1287
maximum-paths Set RIP to forward packets over multiple paths. Syntax maximum-paths number To return to the default values, use the no maximum-paths commands. Parameters number Enter the number of paths. The range is from 1 to 16. The default is 4 paths. Defaults 4 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.
PAGE 1288
neighbor Define a neighbor router with which to exchange RIP information. Syntax neighbor ip-address To delete a neighbor setting, use the no neighbor ip-address command. Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1289
network Enable RIP for a specified network. To enable RIP on all networks connected to the switch, use this command. Syntax network ip-address To disable RIP for a network, use the no network ip-address command. Parameters ip-address Specify an IP network address in dotted decimal format. You cannot specify a subnet. Defaults No RIP network is configured. Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1290
offset-list Specify a number to add to the incoming or outgoing route metrics learned using RIP. Syntax offset-list prefix-list-name {in | out} offset [interface] To delete an offset list, use the no offset-list prefix-list-name {in | out} offset [interface] command. Parameters prefix-list-name Enter the name of an established Prefix list to determine which incoming routes are modified.
PAGE 1291
Usage Information Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. When the offset metric is applied to an interface, that value takes precedence over an offset value that is not extended to an interface. • ip prefix-list — enters PREFIX-LIST mode and configure a prefix list.
PAGE 1292
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. This command is intended for low-speed interfaces. passive-interface Suppress routing updates on a specified interface. Syntax passive-interface interface To delete a passive interface, use the no passive-interface interface command.
PAGE 1293
Usage Information Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1294
Usage Information Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. To redistribute the default route (0.0.0.0/0), configure the default-information originate command.
PAGE 1295
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre- 6.2.1.1 Introduced on the E-Series. redistribute ospf Redistribute routing information from an OSPF process.
PAGE 1296
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series.
PAGE 1297
Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable RIP, assign a network address using the network command. Example Dell(conf)# router rip Dell(conf-router_rip)# Related Commands • network — enables RIP. • exit — returns to CONFIGURATION mode. show config Display the changes you made to the RIP configuration. The default values are not shown.
PAGE 1298
Example Dell(conf-router_rip)# show config ! router rip network 172.31.0.0 passive-interface TenGigabitEthernet 1/1/1/1 Dell(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. Syntax show ip rip database [ip-address mask] Parameters ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If you enter an IP address, also enter a mask for that IP address.
PAGE 1299
Example Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24... Lists the routes and the sources advertising those routes. Dell# show ip rip database Total number of routes in RIP database: 1624 204.250.54.0/24 [50/1] via 192.14.1.3, 00:00:12, GigabitEthernet 1/15/1 204.250.
PAGE 1300
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. Dell# show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.
PAGE 1301
routing table. The flush value should be greater than the update value. The range is from zero (0) to 4294967295. The default is 240 seconds. Defaults • update = 30 seconds • invalid = 180 seconds • holddown = 180 seconds • flush = 240 seconds Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.
PAGE 1302
Defaults The Dell Networking OS sends RIPv1 and receives RIPv1 and RIPv2. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands 1302 Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON.
PAGE 1303
44 Remote Monitoring (RMON) The Dell Networking OS remote monitoring (RMON) is implemented on the platform. Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1304
rmon alarm Set an alarm on any MIB object. Syntax rmon alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] To disable the alarm, use the no rmon alarm number command. Parameters number Enter the alarm integer number from 1 to 65535. The value must be unique in the RMON alarm table. variable Enter the MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.3.
PAGE 1305
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on an interface.
PAGE 1306
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1307
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table.
PAGE 1308
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1309
falling-threshold value event-number Enter the keywords falling-threshold then the value (64 bit) the falling-threshold alarm is either triggered or reset. Then enter the event-number to trigger when the falling threshold exceeds its limit. This value is the same as the alarmFallingEventIndex or the alarmTable of the RMON MIB. If there is no corresponding falling-threshold event, the value is zero. owner string (OPTIONAL) Enter the keyword owner then the owner name to specify an owner for the alarm.
PAGE 1310
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1311
Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1312
show rmon events Display the contents of the RMON event table. Syntax show rmon events [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-toread format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1313
description: event type: LOG. event community: event last time sent: none event owner: event status: OK RMON event entry 113 description: event type: SNMP TRAP. event community: private event last time sent: none event owner: event status: OK RMON event entry 114 description: event type: LOG and SNMP TRAP.
PAGE 1314
Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1315
show rmon history Display the contents of the RMON Ethernet history table. Syntax Parameters show rmon history [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an easy-to-read format Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1316
show rmon log Display the contents of the RMON log table. Syntax show rmon log [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON log table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1317
2 4 Dell# 2 4 show rmon statistics Display the contents of RMON Ethernet statistics table. Syntax Parameters show rmon statistics [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet statistics table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1318
45 Rapid Spanning Tree Protocol (RSTP) The Dell Networking OS implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking OS supports RSTP.
PAGE 1319
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1320
events (OPTIONAL) Enter the keyword events to debug RSTP events. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1321
Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. pre-7.7.1.0 Introduced. • protocol spanning-tree rstp — enters SPANNING TREE mode on the switch.
PAGE 1322
Related Commands Version Description 6.2.1.1 Introduced on the E-Series. • protocol spanning-tree rstp — enters SPANNING TREE mode on the switch. forward-delay Configure the amount of time the interface waits in the Listening State and the Learning State before transitioning to the Forwarding State. Syntax forward-delay seconds To return to the default setting, use the no forward-delay command.
PAGE 1323
hello-time Set the time interval between the generation of the RSTP bridge protocol data units (BPDUs). Syntax hello-time [milli-second] seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10 seconds. The default is 2 seconds. milli-second Enter the keywords milli-second to configure a hello time on the order of milliseconds.
PAGE 1324
• max-age — changes the wait time before RSTP refreshes the protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the RSTP bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40 seconds. The default is 20 seconds.
PAGE 1325
To exit RSTP mode, use the exit command. Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1326
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1327
Usage Information Example (Brief) Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added support for the optional guard keyword on the C-Series, S-Series, and E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display the port error disable state (EDS) caused by loopback BPDU inconsistency. 6.2.1.
PAGE 1328
Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID - ---- ------- --- ------- -------------------- -------Te 1/1/1/1 128.257 128 20000 EDS 0 32768 0001.e801.6aa8 128.257 Interface Name Role PortID Prio Cost Sts Cost Link-type Edge --- ------ -------- ---- ------- --- ------- --------- ---Te 1/1/1/1 ErrDis 128.257 128 20000 EDS 0 P2P No Dell# show spanning-tree rstp Root Identifier has priority 32768, Address 0001.e801.
PAGE 1329
bpduguard (OPTIONAL) Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails. Enter the keyword bpduguard to disable the port when it receives a BPDU. shutdown-onviolation (OPTIONAL) Enter the keywords shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled. priority priority Enter keyword priority then a value in increments of 16 as the priority. The range is from 0 to 240.
PAGE 1330
NOTE: A port configured as an edge port, on an RSTP switch, immediately transitions to the Forwarding state. Only configure ports connected to end-hosts as edge ports. Consider an edge port similar to a port with a spanning-tree portfast enabled. If you do not enable shutdown-on-violation, BPDUs are still sent to the RPM CPU. You cannot enable STP root guard and loop guard at the same time on a port.
PAGE 1331
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. By default, Dell Networking OS implements an optimized flush mechanism for RSTP. This implementation helps in flushing MAC addresses only when necessary (and less often), allowing for faster convergence during topology changes.
PAGE 1332
46 Security The commands in this chapter are available on Dell Networking OS. For configuration details, see the Security section in the Dell Networking OS Configuration Guide. NOTE: Dell Networking OS implements LEAP with MSCHAP v2 supplicant. Topics: • AAA Accounting Commands • Authorization and Privilege Commands • Obscure Password Commands • Authentication and Password Commands • RADIUS Commands • TACACS+ Commands • Port Authentication (802.
PAGE 1333
exec Enter the keyword exec to send accounting information when a user has logged in to EXEC mode. commands {level | role role-name Enter the keyword command then a privilege level for accounting of commands executed at that privilege level or enter the keyword role then the role name for accounting of commands executed by a user with that user role. name | default Enter one of the following: • For name, enter a user-defined name of a list of accounting methods.
PAGE 1334
Privilege level 15 is the default. If you want to track usage at privilege level 1 for example, use the aaa accounting command 1 command. Example Dell(conf)# aaa accounting exec default start-stop tacacs+ Dell(conf)# aaa accounting command 15 default start-stop tacacs+ Dell(conf)# aaa accounting command role secaadmin default start-stop tacacs+ Related Commands • enable password — changes the password for the enable command.
PAGE 1335
login method-list none command is applied. To prevent the accounting records from being generated for sessions that do not have user names associated to them, use the aaa accounting suppress command. accounting Apply an accounting method list to terminal lines. Syntax Parameters accounting {exec | commands {level | role role-name} method-list exec Enter the keyword exec to apply an EXEC level accounting method list.
PAGE 1336
Related Commands • aaa accounting — enables AAA Accounting and creates a record for monitoring the accounting function. aaa radius group Configure the RADIUS server group that is used for Authentication, Authorization and Accounting. Syntax aaa radius group group-name To remove the RADIUS group configuration, use the no aaa radius group group-name command. Parameters group-name Enter the name of the RADIUS server group.
PAGE 1337
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL.
PAGE 1338
Authorization and Privilege Commands To set command line authorization and privilege levels, use the following commands. authorization Apply an authorization method list to terminal lines. Syntax authorization {exec | commands {level | role role-name}} method-list Parameters exec Enter the keyword exec to apply an EXEC level authorization method list.
PAGE 1339
Related Commands • aaa authorization commands — sets the parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands. • aaa authorization exec — sets the parameters that restrict (or permit) a user’s access to EXEC level commands. aaa authorization commands Set parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands.
PAGE 1340
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Added support for RADIUS. Certain TACACS+ servers do not authenticate the device if you use the aaa authorization commands level default local tacacs+ command. To resolve the issue, use the aaa authorization commands level default tacacs+ local command. aaa authorization config-commands Set parameters that restrict (or permit) a user’s access to EXEC level commands.
PAGE 1341
aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands. Syntax aaa authorization exec {name | default} {local || tacacs+ || if-authenticated || none} To disable authorization checking for EXEC level commands, use the no aaa authorization exec command. Parameters name Define a name for the list of authorization methods. default Define the default list of authorization methods.
PAGE 1342
To delete access to a level and command, use the no privilege mode level level command command. Parameters mode level level Enter one of the following keywords as the mode for which you are controlling access: • configure for CONFIGURATION mode • exec for EXEC mode • interface for INTERFACE modes • line for LINE mode • route-map for ROUTE-MAP mode • router for ROUTER OSPF, ROUTER RIP, ROUTER ISIS and ROUTER BGP modes Enter the keyword level then a number for the access level.
PAGE 1343
privilege level (LINE mode) Change the access level for users on the terminal lines. Syntax privilege level level To delete access to a terminal line, use the no privilege level level command. Parameters level level Enter the keyword level then a number for the access level. The range is from 0 to 15. Level 1 is EXEC mode and Level 15 allows access to all CLI modes. Defaults level = 15 Command Modes LINE Command History This guide is platform-specific.
PAGE 1344
Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication, use the service obscure-passwords command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1345
Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | method-listname} method [... method2] command.
PAGE 1346
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell Networking OS uses the methods defined for Enable access instead.
PAGE 1347
... method4 • local: use the password for the userid contained in the local password database. • none: no authentication. Not available if role-only is in use. • radius: use the RADIUS servers configured with the radius-server host command. • tacacs+: use the TACACS+ servers configured with the tacacs-server host command. (OPTIONAL) Enter up to four additional methods.
PAGE 1348
Methods configured with the aaa authentication login command are evaluated in the order they are configured. If users encounter an error with the first method listed, Dell Networking OS applies the next method configured. If users fail the first method listed, no other methods are applied. The only exception is the local method. If the user’s name is not listed in the local database, the next method is applied.
PAGE 1349
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. • line — applies an authentication method list to the designated terminal lines. • ip access-list standard — names (or selects) a standard access list to filter based on the IP address. • ip access-list extended — names (or selects) an extended access list based on the IP addresses or protocols.
PAGE 1350
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command.
PAGE 1351
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1352
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1353
default Enter the keyword default to specify that the default method list, created in the aaa authentication login command, is applied to the terminal line. Defaults No authentication is performed on the console lines. Local authentication is performed on the virtual terminal and auxiliary lines. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1354
password Specify a password for users on terminal lines. Syntax password [encryption-type] password To delete a password, use the no password password command. Parameters encryption-type password (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the password entered. The options are • 0 is the default and means the password is not encrypted and stored as clear text. • 7 means that the password is encrypted and hidden. Enter a text string up to 32 characters long.
PAGE 1355
• radius-server key — configures a key for all RADIUS communications between the switch and the RADIUS host server. • tacacs-server key — configures a key for communication between a TACACS+ server and client. • username — establishes an authentication system based on user names. password-attributes Configure the password attributes (strong password).
PAGE 1356
Example Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced lockout-period option on the Z9500. 9.5(0.0) Introduced lockout-period option on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1357
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information CAUTION: Encrypting passwords with this command does not provide a high level of security.
PAGE 1358
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell# show privilege Current privilege level is 15. Dell# Dell# show privilege Current privilege level is 14. Dell# Dell# show privilege Current privilege level is 10.
PAGE 1359
Usage Information Example Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show user command shown in the following example. Field Description (untitled) Indicates with an asterisk (*) which terminal line you are using. Line Displays the terminal lines currently in use.
PAGE 1360
• AUX — range is from 1 to 300 seconds, the default is 0 seconds (no timeout). Defaults See Parameters. Command Modes LINE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1361
encryption-type Enter an encryption type for the password that you enter. • 0 directs the system to store the password as clear text. It is the default encryption type when using the password option. • 8 to indicate that a password encrypted using a sha256 hashing algorithm follows. This encryption type is available with the sha256-password option only, and is the default encryption type for this option. • 7 to indicate that a password encrypted using a DES hashing algorithm follows.
PAGE 1362
Usage Information Related Commands To view the defined user names, use the show running-config user command. • password — specifies a password for users on terminal lines. • show running-config — views the current configuration. RADIUS Commands The following RADIUS commands are supported by Dell Networking OS. debug radius View RADIUS transactions to assist with troubleshooting. Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled.
PAGE 1363
ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections. Syntax ip radius source-interface interface To delete a source interface, use the no ip radius source-interface command. Parameters interface Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1364
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped. Syntax radius-server deadtime seconds To disable this function or return to the default value, use the no radius-server deadtime command. Parameters seconds Enter a number of seconds during which non-responsive RADIUS servers are skipped.
PAGE 1365
Parameters group-name Enter the group name that denotes the group of RADIUS servers. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1366
For the encryption-type, enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the password is not encrypted and stored as clear text. • 7 means that the password is encrypted and hidden. Configure this parameter last because leading spaces are ignored. Defaults Not configured. Command Modes Command History Usage Information • RADIUS SERVER GROUP • CONFIGURATION This guide is platform-specific.
PAGE 1367
you configure the timeout, retransmit, or key values, include those keywords when using the no radiusserver host command syntax. You can use duplicate host names or IP addresses among RADIUS groups. However, you cannot use duplicate host names or IP addresses within the same RADIUS group. If a VRF is not configured on the RADIUS group, then servers configured in the group are considered to be on the default VRF.
PAGE 1368
• For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes RADIUS SERVER GROUP Command History This guide is platform-specific.
PAGE 1369
To delete a password, use the no radius-server key command. Parameters encryption-type key (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the key is not encrypted and stored as clear text. • 7 means that the key is encrypted and hidden. Enter a string that is the key to be exchanged between the switch and RADIUS servers. It can be up to 42 characters long. Defaults Not configured.
PAGE 1370
radius-server retransmit Configure the number of times the switch attempts to connect with the configured RADIUS host server before declaring the RADIUS host server unreachable. Syntax radius-server retransmit retries To configure zero retransmit attempts, use the no radius-server retransmit command. To return to the default setting, use the radius-server retransmit 3 command. Parameters retries Enter a number of attempts that the Dell OS tries to locate a RADIUS server.
PAGE 1371
To return to the default value, use the no radius-server timeout command. Parameters seconds Enter the number of seconds between an unsuccessful attempt and the Dell Networking OS times out. The range is from zero (0) to 1000 seconds. The default is 5 seconds. Defaults 5 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1372
Parameters group-name Enter the name of the TACACS server group. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1373
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. ip tacacs source-interface Specify an interface’s IP address as the source IP address for TACACS+ connections.
PAGE 1374
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 1375
Related Commands • aaa authentication login — specifies the login authentication method. • tacacs-server key — configures a TACACS+ key for the TACACS server. tacacs-server host Specify a TACACS+ host. Syntax Parameters tacacs-server host {hostname | ipv4-address | ipv6-address} [port number] [timeout seconds] [key key] hostname Enter the name of the TACACS+ server host. ipv4-address | ipv6address Enter the IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of the TACACS+ server host.
PAGE 1376
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. To list multiple TACACS+ servers to be used by the aaa authentication login command, configure this command multiple times. If you are not configuring the switch as a TACACS+ server, you do not need to configure the port, timeout and key optional parameters. If you do not configure a key, the key assigned in the tacacs-server key command is used.
PAGE 1377
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.
PAGE 1378
• For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 1379
• If no VLAN is supplied by the RADIUS server or if 802.1X authorization is disabled, the port is configured in its access VLAN after successful authentication. • If 802.1X authorization is enabled but the VLAN information from the RADIUS server is not valid, the port returns to the Unauthorized state and remains in the configured access VLAN. This prevents ports from appearing unexpectedly in an inappropriate VLAN due to a configuration error. Configuration errors create an entry in Syslog. • If 802.
PAGE 1380
dot1x authentication (Interface) Enable dot1x on an interface; dot1x must be enabled both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.
PAGE 1381
Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.
PAGE 1382
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.
PAGE 1383
Usage Information 802.1X authentication is enabled when an interface is connected to the switch. If the host fails to respond within a designated amount of time, the authenticator places the port in the guest VLAN. If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable. Therefore, a guest VLAN is allocated to the interface and authentication for the device occurs at the next re-authentication interval (dot1x reauthentication).
PAGE 1384
dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command. Parameters number Enter the number of times an EAP request is transmitted before a session time-out. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1385
force-unauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1386
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic re-authentication of the client.
PAGE 1387
Related Commands Version Description 7.4.1.0 Introduced on the E-Series. • interface range — configures a range of interfaces. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command. Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2.
PAGE 1388
To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1389
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1390
Version Description 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. show dot1x interface Display the 802.1X information on an interface. Syntax show dot1x interface interface Parameters Defaults Enter one of the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1391
Example Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series, S-Series, and E-Series. Dell#show dot1x interface fortyGigE 1/10 802.
PAGE 1392
SSH and SCP Commands Dell Networking OS supports secure shell (SSH) protocol versions 1.5 and 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted and use authentication. crypto key generate Generate keys for the SSH server. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative.
PAGE 1393
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The host keys are required for key-exchange by the SSH server. If the keys are not found when you enable the server (ip ssh server enable), the keys are automatically generated. This command requires user interaction and generates a prompt prior to overwriting any existing host keys. NOTE: Only a user with superuser permissions should generate host-keys.
PAGE 1394
debug ip ssh Enables collecting SSH debug information. Syntax debug ip ssh {client | server} To disable debugging, use the no debug ip ssh {client | server} command. Parameters client Enter the keyword client to enable collecting debug information on the client. server Enter the keyword server to enable collecting debug information on the server. Defaults Disabled on both client and server. Command Modes EXEC Command History This guide is platform-specific.
PAGE 1395
Parameters directory Enter a directory name. Defaults The internal flash (flash:) is the default directory. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1396
Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.
PAGE 1397
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server.
PAGE 1398
Usage Information If you enable this command, clients can log in without a password prompt. This command provides two levels of authentication: • rhost-authentication is done with the file specified in the ip ssh rhostfile command. • checking client host-keys is done with the file specified in the ip ssh pub-key-file command. NOTE: Administrators must specify the two files (rhosts and pub-key-file) to configure hostbased authentication.
PAGE 1399
ip ssh password-authentication Enable password authentication for the SSH server. Syntax ip ssh password-authentication enable To disable password-authentication, use the no ip ssh password-authentication enable command. Parameters enable Enter the keyword enable to enable password-authentication for the SSH server. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1400
Parameters time minutes Enter the keywords time then the amount of time in minutes. The range is from 10 to 1440 minutes. The default is 60 minutes volume rekeylimit Enter the keywords volume then the amount of volume in megabytes. The range is from 1 to 4096 to megabytes. The default is 1024 megabytes Defaults The default time is 60 minutes. The default volume is 1024 megabytes. Command Modes CONFIGURATION mode Command History This guide is platform-specific.
PAGE 1401
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication. The creates/ file overwrites the flash://ADMIN_DIR/ssh/knownhosts file and deletes the user-specified file.
PAGE 1402
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1403
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1404
The default cipher list is used. mac hmacalgorithm • 3des-cbc • aes128-cbc • aes192-cbc • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr Enter the keyword mac then a space-delimited list of hash message authentication code (HMAC) algorithms supported by the SSH server for keying hashing for the message authentication. The following HMAC algorithms are available: • hmac-sha1 • hmac-sha1-96 • hmac-sha2-256 When FIPS is enabled, the default HMAC algorithm is hmac-sha1-96.
PAGE 1405
[version {1 | 2}] (OPTIONAL) Enter the keyword version then the SSH version 1 or 2 to specify only SSHv1 or SSHv2. NOTE: If you enable FIPS mode, you can only select version 2. Defaults • Default listening port is 22. • Default cipher list is 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192-ctr,aes256-ctr. • When FIPS is enabled, the default is hmac-sha1-96. • When FIPS is not enabled, the default is hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmac-sha2-256.
PAGE 1406
Example Dell# conf Dell(conf)# ip ssh server port 45 Dell(conf)# ip ssh server enable Dell# ip ssh server vrf Configure an SSH server on either a specific VRF or a management VRF. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative. ip ssh server vrf {any | management | vrf-name} To disable the SSH server configuration, use the no ip ssh server vrf {management | vrf-name} command.
PAGE 1407
• • • • Related Commands • Dell(conf)# Dell(conf)# Dell(conf)# Dell(conf)# ip no ip no ssh server vrf vrf1 ip ssh server vrf ssh server vrf management ip ssh server vrf show ip ssh — displays the ssh information. ip ssh source-interface Specifies an interface’s IP address as the source IP address for an outgoing SSH connections. Syntax ip ssh source-interface interface To delete a source interface, use the no ip ssh source-interface command.
PAGE 1408
Version Description 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information The source-interface interface attribute is applicable for both the SSH client as well as the COPY (SCP) commands. Using these attributes the client session tags an error to the user during run time, in case there is a mismatch between this command and the ip ssh vrf command. Example Dell(conf)#ip ssh source-interface tengigabitethernet 1/1/3/1 Dell(conf)#do ssh 10.10.10.
PAGE 1409
show crypto Display the public part of the SSH host-keys. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative. show crypto key mypubkey {rsa | rsa1} Parameters Key Enter the keyword key to display the host public key. mypubkey Enter the keyword mypubkey to display the host public key. rsa Enter the keyword rsa to display the host SSHv2 RSA public key.
PAGE 1410
Dell# show crypto key mypubkey rsa ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQC9IYgcUcc8wQm+5KUQgW/ zAs8V5STalGq4/+S+6H9axpQnA+A0xweeo5iR5hvPP6Vc+HS+uWoQH+ VOJ8H5Jxsm347XnYv/gpSqhgjZ/C5UwFiucVkVfYu8RDcJVIuQhLv PEebIF5Q+sD8K89MXU90MAS/UdoiJZSOIlbaCuSTW1Q== Dell# Related Commands • crypto key generate — generates the SSH keys. show ip ssh Display information about established SSH sessions. Syntax NOTE: Some of the parameters in this command require licensing to access.
PAGE 1411
ctr,aes128-cbc,3des-cbc. SSH server macs : hmac-sha2-256,hmac-sha1,hmac-sha1-96,hmac-md5,hmacmd5-96. SSH server kex algorithms : diffie-hellman-group-exchange-sha1,diffie-hellmangroup1-sha1,diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Challenge Response Auth : enabled. Vty Encryption HMAC Remote IP 2 aes128-cbc hmac-md5 10.16.127.141 4 aes128-cbc hmac-md5 10.16.127.141 * 5 aes128-cbc hmac-md5 10.16.127.
PAGE 1412
Example Dell# show ip ssh client-pub-keys 4.8.1.2 ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAu5NoTbmnLxBknaeXZmUJMupNwNUoGlo1/ yLPI5eehQTyaldRPHtGyPlcmMbCH +QJkqtyiwDPmH4njyDMYDCXY85vc55ibWsN9qalagklnh2cj2q4nYj5x8+8OOhYeFPaHiygd8U/ FXict61jWs84Co1UTsAgRzDJ9aUSS75TVac= root@dt-maa-linux-1.force10networks.
PAGE 1413
Example Dell# show ip ssh rsa-authentication my-authorized-keys ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAyB17l4gFp4r2DRHIvMc1VZ d0Sg5GQxRV1y1X1JOMeO6Nd0WuYyzrQMM 4qJAoBwtneOXfLBcHF3V2hcMIqaZN+CRCnw/ zCMlnCf0+qVTd1oofsea5r09kS0xTp0CNfHXZ3NuGCq9Ov33m9+ U9tMwhS8vy8AVxdH4x4km3c3t5Jvc= freedom@poclab4 Dell# Related Commands • ip ssh rsa-authentication (Config) — configures the RSA authorized keys.
PAGE 1414
• aes128-ctr : Force ssh to use aes128-ctr encryption cipher • aes192-ctr : Force ssh to use aes192-ctr encryption cipher • aes256-ctr : Force ssh to use aes256-ctr encryption cipher -l username (OPTIONAL) Enter the keyword -l then the user name used in this SSH session. The default is the user name of the user associated with the terminal. -m HMAC algorithm Enter one of the following HMAC algorithms to use. (For v2 clients only): "no fips mode enable"(disable) will support v1 & v2 client.
PAGE 1415
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Added support for the -c and -m parameters on the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Added IPv6 support. Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information Dell Networking OS supports both inbound and outbound SSH sessions using IPv4 or IPv6 addressing.
PAGE 1416
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. • show ip dhcp snooping — display the contents of the DHCP binding table. ip dhcp relay Enable Option 82.
PAGE 1417
Version Description 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1418
Defaults Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094. ip ip-address Enter the keyword ip then the IP address that the server is leasing. interface type Enter the keyword interface then the type of interface to which the host is connected. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1419
Related Commands • show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp snooping database renew Renew the binding table. Syntax ip dhcp snooping database renew Defaults none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1420
Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp source-address-validation Enable IP source guard.
PAGE 1421
ip dhcp snooping vlan Enable DHCP Snooping on one or more VLANs. Syntax Parameters [no] ip dhcp snooping vlan name name Enter the name of a VLAN on which to enable DHCP Snooping. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.
PAGE 1422
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1423
inherit existing-rolename Enter the inherit keyword then specify the system defined role to inherit permissions from (sysadmin, secadmin, netadmin, netoperator). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.
PAGE 1424
line for LINE mode route-map for Route-map mode router for Router mode addrole Enter the keyword addrole to add permission to the command. You cannot add or delete rights for the sysadmin role. deleterole Enter the keyword deleterole to remove access to the command. You cannot add or delete rights for the sysadmin role. role-name Enter a text string for the name of the user role up to 63 characters. These are 3 system defined roles you can modify: secadmin, netadmin, and netoperator.
PAGE 1425
• interface • line • route-map • router Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Examples Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 1426
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL.
PAGE 1427
Usage Information Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL. Instead of using the system defined user roles, you can create a new user role that best matches your organization.
PAGE 1428
47 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging section. This section includes command line information (CLI) for the Dell Networking OS Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell Networking OS supports L2PT on Dell Networking OS.
PAGE 1429
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information.
PAGE 1430
protocol-tunnel Enable protocol tunneling on a stacked (Q-in-Q) VLAN for specified protocol packets. Syntax protocol-tunnel {rate-limit rate| stp} To disable protocol tunneling for a Layer 2 protocol, use the no protocol-tunnel command. Parameters rate-limit rate Enter the keyword rate-limit followed by a number for the rate-limit for tunneled packets on the VMAN. The range is from 64 to 320.
PAGE 1431
protocol-tunnel destination-mac Overwrite the BPDU destination MAC address with a specific value. Syntax Parameters protocol-tunnel destination-mac xstp address stp Change the default destination MAC address used for L2PT to another value. Defaults The default destination MAC is 01:01:e8:00:00:00. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1432
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1433
Example Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and E-Series. Maximum rate limit on E-Series reduced from 4000 to 3000. 7.4.1.
PAGE 1434
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and E-Series. 7.4.1.
PAGE 1435
48 sFlow The Dell Networking OS supports sFlow commands. The Dell Networking OS sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1436
sflow collector Configure a collector device to which sFlow datagrams are forwarded. Syntax sflow collector {ip-address | ipv6-address} agent-addr {ip-address | ipv6address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command.
PAGE 1437
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.4.2.3 Added support for IPv6 sFlow collectors and agents on the E-series, C-Series, and SSeries. 8.4.1.1 Added support for IPv6 sFlow collectors and agents on the E-series. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.5.1.
PAGE 1438
Usage Information Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.0 Introduced on the S-Series.
PAGE 1439
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. When you enable ingress sFlow on an interface, flow sampling is done on any incoming traffic. NOTE: After a physical port is a member of a LAG, it inherits the sFlow configuration from the LAG port. Related Commands • sflow enable (Global) — turn sFlow globally. sflow extended-switch enable Enable packing information on a switch only.
PAGE 1440
Usage Information Related Commands Dell Networking OS enhances the sflow implementation for real time traffic analysis on the E-Series to provide extended gateway information in cases where the destination IP addresses are learned by different routing protocols and for cases where the destination is reachable over ECMP. • show sflow — displays the sFlow configuration. sflow max-header-size extended Set the maximum header size of a packet to 256 bytes.
PAGE 1441
Defaults 20 seconds Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500.
PAGE 1442
Command History Usage Information Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1443
Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.
PAGE 1444
Usage Information Related Commands Version Description 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series. 7.7.1.
PAGE 1445
• Command Modes Command History • EXEC • EXEC Privilege For a port-channel interface, enter the keywords port-channel then the portchannel ID. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100-ON. 9.8(1.0) Introduced on the Z9100-ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1446
49 Simple Network Management Protocol (SNMP) and Syslog This section contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell Networking OS. Topics: • SNMP Commands • Syslog Commands SNMP Commands The following SNMP commands are available in the Dell Networking OS.
PAGE 1447
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1448
• Command History Example EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1449
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The following Example displays a group named ngroup.
PAGE 1450
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1451
Example Version Description 7.5.1.0 Introduced on the C-Series. unknown Introduced on the E-Series. Dell#config!------command run on host connected to switch: --------------! > snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2. This is a port connected to IF-MIB::ifAlias.
PAGE 1452
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.
PAGE 1453
Dell(conf)# snmp-server community guest ro snmp-ro-acl Dell(conf)# Related Commands • ip access-list standard — names (or selects) a standard access list to filter based on IP address. • ipv6 access-list — configures an access list based on IPv6 addresses or protocols. • show running-config — displays the current SNMP configuration and defaults. snmp-server contact Configure contact information for troubleshooting this SNMP node.
PAGE 1454
snmp-server enable traps Enable SNMP traps. Syntax snmp-server enable traps [notification-type] [notification-option] To disable traps, use the no snmp-server enable traps [notification-type] [notificationoption] command. Parameters notification-type notification-option Enter the type of notification from the following list: • bgp — Notification of changes in the BGP process. • config — Notification of changes to the startup or running configuration. • ecfm — Notification of changes to ECFM.
PAGE 1455
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the following two SNMP notification options: syslog-reachable and syslog-unreachable. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.
PAGE 1456
Format (as specified in RFC 3411): 12 octets. • The first four octets are set to the private enterprise number. • The remaining eight octets are the MAC address of the chassis. remote ip-address Enter the keyword remote followed by the IP address that identifies the copy of the SNMP on the remote device. vrf vrf-name Enter the keyword vrf followed by the name of the VRF that is used to reach the device. NOTE: Use this attribute to specify the VRF that is used by the SNMP engine to reach the device.
PAGE 1457
Related Commands • show snmp engineID — displays the SNMP engine and all the remote engines that are configured on the router. • show running-config snmp — displays the SNMP running configuration. snmp-server group Configure a new SNMP group or a table that maps SNMP users to SNMP views.
PAGE 1458
access-list-name ipv6 access-listname (Optional) Enter both an IPv4 and IPv6 access list name. Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1459
snmp-server host Configure the recipient of an SNMP trap operation. Syntax snmp-server host ip-address | ipv6-address [vrf vrf-name] traps | informs [version 1 | 2c | 3] [auth | no auth | priv] [community-string] [udp-port portnumber] [notification-type] To remove the SNMP host, use the no snmp-server host ip-address [vrf vrf-name] traps | informs [version 1 | 2c | 3] [auth | noauth | priv] [community-string] [udpport number] [notification-type] command.
PAGE 1460
NOTE: For version 1 and version 2c security models, this string represents the name of the SNMP community. The string can be set using this command; however, Dell Networking OS recommends setting the community string using the snmp-server community command before executing this command. For version 3 security model, this string is the USM user security name. udp-port portnumber (OPTIONAL) Enter the keywords udp-port followed by the port number of the remote host to use. The range is from 0 to 65535.
PAGE 1461
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for VRRP traps. 7.6.1.0 Added support for STP and xSTP notification types. Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To configure the router to send SNMP notifications, enter at least one snmp-server host command.
PAGE 1462
snmp-server location Configure the location of the SNMP server. Syntax snmp-server location text To delete the SNMP location, use the no snmp-server location command. Parameters text Enter an alpha-numeric text string, up to 55 characters long. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1463
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1464
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults The IP address assigned to the management interface is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1465
Parameters name Enter the name of the user (not to exceed 20 characters), on the host that connects to the agent. group_name Enter a text string (up to 20 characters long) as the name of the group. The following groups are created for mapping to read/write community/security-names (defaults): • v1v2creadu — maps to a community with ro permissions. • 1v2cwriteu — maps to a community rw permissions.
PAGE 1466
ipv6 access-listname (Optional) Enter the keyword ipv6 then the IPv6 access list name (a string up to 16 characters long). access-list-name ipv6 access-listname (Optional) Enter both an IPv4 and IPv6 access list name. Defaults As above. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.
PAGE 1467
Example Dell#conf Dell(conf)# snmp-server user authuser v3group v3 auth md5 authpasswd Usage Information The following command configures a remote user named n3user with a v3 security model and a security level of authNOPriv. Example Dell#conf Dell(conf)# snmp-server user n3user ngroup remote 172.31.1.3 udp-port 5009 3 auth md5 authpasswd Related Commands • show snmp user — displays the information configured on each SNMP user name.
PAGE 1468
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.
PAGE 1469
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1470
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Use this command to bind an SNMP agent to a VRF. The SNMP agent processes the requests from the interfaces that belong to the specified VRF. If no VRF is specified, then the default VRF is used. • show snmp user — display the information configured on each SNMP user name.
PAGE 1471
Version Description E-Series legacy command Usage Information If the interface is expected to flap during normal usage, you could disable this command. Syslog Commands The following commands allow you to configure logging functions on all Dell Networking switches. clear logging Clear the messages in the logging buffer. Syntax clear logging Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1472
clear logging auditlog Clears audit log. Syntax clear logging auditlog Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the MXL.
PAGE 1473
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • logging buffered — set the logging buffered parameters. default logging console Return the default settings for messages logged to the console. Syntax default logging console Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1474
default logging monitor Return to the default settings for messages logged to the terminal. Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1475
Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1476
NOTE: Use this attribute to specify the VRF that is used to contact the host. By default, the default VRF is used. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1477
To return to the default values, use the default logging buffered command. To disable logging stored to an internal buffer, use the no logging buffered command. Parameters level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following equivalent words: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging. size (OPTIONAL) Indicate the size, in bytes, of the logging buffer.
PAGE 1478
logging console Specify which messages are logged to the console. Syntax logging console [level] To return to the default values, use the default logging console command. To disable logging to the console, use the no logging console command. Parameters level (OPTIONAL) Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1479
logging extended Logs security and audit events to a system log server. Syntax logging extended Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1480
Parameters facility-type (OPTIONAL) Enter one of the following parameters: • auth (authorization system) • cron (Cron/at facility) • deamon (system deamons) • kern (kernel) • local0 (local use) • local1 (local use) • local2 (local use) • local3 (local use) • local4 (local use) • local5 (local use) • local6 (local use) • local7 (local use) • lpr (line printer system) • mail (mail system) • news (USENET news) • sys9 (system use) • sys10 (system use) • sys11 (system use) •
PAGE 1481
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • logging — enables logging to a Syslog server • logging on — enables logging. logging history Specify which messages are logged to the history table of the switch and the SNMP network management station (if configured).
PAGE 1482
Version Description E-Series legacy command Usage Information Related Commands When you configure the snmp-server trap-source command, the system messages logged to the history table are also sent to the SNMP network management station. • show logging — displays information logged to the history buffer. logging history size Specify the number of messages stored in the Dell Networking logging history table.
PAGE 1483
Related Commands • show logging — displays information logged to the history buffer. logging monitor Specify which messages are logged to Telnet applications. Syntax logging monitor [level] To disable logging to terminal connections, use the no logging monitor command. Parameters level Indicate a value from 0 to 7 or enter one of the following parameters: emergencies, alerts, critical, errors, warnings, notifications, informational, or debugging. The default is 7 or debugging.
PAGE 1484
logging on Specify that debug or error messages are asynchronously logged to multiple destinations, such as the logging buffer, Syslog server, or terminal lines. Syntax logging on To disable logging to logging buffer, Syslog server and terminal lines, use the no logging on command. Defaults Enabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1485
To disable this command and return to the default setting, use the no logging source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information.
PAGE 1486
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Related Commands Syslog messages contain the IP address of the interface used to egress the router. By configuring the logging source-interface command, the Syslog packets contain the IP address of the interface configured. • logging — enables logging to the Syslog server. logging synchronous Synchronize unsolicited messages and Dell Networking OS output.
PAGE 1487
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you enable logging synchronous, unsolicited messages appear between software prompts and outputs. Only the messages with a severity at or below the set level are sent to the console. If the message queue limit is reached on a terminal line and messages are discarded, a system message appears on that terminal line.
PAGE 1488
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Related Commands To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5. • logging — enables the logging to another device. • logging on — enables logging.
PAGE 1489
Example Dell(conf)#logging version ? <0-1> Select syslog version (default = 0) Dell(conf)#logging version 1 show logging auditlog Displays an audit log. Syntax show logging auditlog Defaults None Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 1490
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1491
Oct 8 09:26:25: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 1.1.14.2 closed. Neighbor recycled --More-Example (History) Dell#show logging history Syslog History Table: 1 maximum table entries, saving level Warnings or higher SNMP notifications not Enabled %RPM:0:0 %CHMGR-2-LINECARDDOWN - Line card 3 down - IPC timeout Dell# show logging driverlog stack-unit Display the driver log for the specified hardware component.
PAGE 1492
Cannot enable psu -127228353 2:Task(tUsrRoot): [ 6876]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main block failed checksum calulated checksum 0x1d actual chksum 0x0 3:Task(tUsrRoot): [ 61]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Main block failed errcode 6 4:Task(tUsrRoot): [ 89]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed checksum calulated checksum 0xc9a6 actual chksum 0x0 5:Task(tUsrRoot): [ 57]EEPROM LIB ERR: f10EepromBlkRead@psu0eeprom: Redundant block failed errcode 6 6:T
PAGE 1493
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands • logging monitor — set the logging parameters on the monitor/terminal.
PAGE 1494
50 SNMP Traps This section lists the traps sent by the Dell Networking OS. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Table 3. SNMP Trap List Message ID Trap Type Trap Option COLD_START SNMP COLDSTART WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP LINKDOWN SNMP LINKUP SNMP AUTH EGP_NEIGHBOR_LOSS SNMP NONE OSTATE_DOWN SNMP LINKDOWN SNMP LINKUP SNMP NONE %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent.
PAGE 1495
Message ID Trap Type Trap Option SNMP NONE SNMP NONE SNMP NONE SNMP NONE SNMP NONE SNMP NONE NONE NONE CHM_CARD_PROBLEM ENVMON NONE CHM_ALARM_CUTOFF ENVMON NONE CHM_SFM_UP ENVMON NONE CHM_SFM_DOWN ENVMON NONE CHM_RPM_UP ENVMON NONE ENVMON NONE rising threshold alarm from SNMP OID RMON_FALLING_THRESHOLD %RPM0-P:CP %SNMP-4RMON_FALLING_THRESHOLD: RMON falling threshold alarm from SNMP OID RMON_HC_RISHING_THRESHOLD %RPM0-P:CP %SNMP-4RMON_HC_RISING_THRESHOLD: RMON hi
PAGE 1496
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY %CHMGR-2-RPM_DOWN: RPM 0 down card removed CHM_RPM_PRIMARY %RAM-5-COLD_FAILOVER: RPM Failover Completed %RAM-5-HOT_FAILOVER: RPM Failover Completed %RAM-5-FAST_FAILOVER: RPM Failover Completed CHM_SFM_ADD %TSM-5-SFM_DISCOVERY: Found SFM 1 CHM_SFM_REMOVE %TSM-5-SFM_REMOVE: Removed SFM 1 CHM_MAJ_SFM
PAGE 1497
Message ID Trap Type Trap Option ENVMON SUPPLY ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON FAN ENVMON FAN ENVMON FAN %CHMGR-1-MINOR_PS: Minor alarm: power supply non-redundant CHM_MIN_ALARM_PS_CLR %CHMGR-5-MINOR_PS_CLR: Minor alarm cleared: power supply redundant CHM_MIN_ALRM_TEMP %CHMGR-2-MINOR_TEMP: Minor alarm: chassis temperature CHM_MIN_ALRM_TEMP_CLR %CHMRG-5-MINOR_TEMP_CLR: Minor alarm cleared: chassis temperature normal (%s %d temperature is within threshold of %dC) CHM_
PAGE 1498
Message ID Trap Type Trap Option ENVMON FAN ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE For the E1200: %CHMGR-2FAN_BAD: Minor alarm: some fans in fan tray %d are down For the E600 and E300: %CHMGR2-1FANBAD: Minor alarm: fan in fan tray is down CHM_MIN_FANBAD_CLR For E1200: %CHMGR-2-FAN_OK: Minor alarm cleared: all fans in fan tray %d are good For E600 and E300: %CHMGR-5FANOK: Minor alarm cleared: all fans in fan tray are
PAGE 1499
Message ID Trap Type Trap Option ENVMON NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE %CHMGR-1-PORT_TEMP_MINOR: Minor Alarm Interface %s temperature exceeds threshold PORT_TEMP_MAJOR_CLR %CHMGR-1-PORT_TEMP_MAJOR_CLR: Major Alarm cleared for Interface %s port temperature is lower than threshold VRRP_BADAUTH %RPM1-P:RP2 %VRRP-3VRRP_BAD_AUTH: vrid-1 on Gi 11/12 rcvd pkt with authentication type mismatch.
PAGE 1500
51 Storm Control The Dell Networking OS storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell Networking OS. Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1501
• storm-control broadcast (Configuration) • storm-control broadcast (Interface) • storm-control multicast (Configuration) • storm-control multicast (Interface) • storm-control unknown-unicast (Configuration) • storm-control unknown-unicast (Interface) polling-interval You can set the time interval to poll the queue depth and egress counters. Syntax Parameters polling—interval {interval in milli-seconds} interval in milliseconds Enter the polling interval in milliseconds.
PAGE 1502
Version Description 9.10(0.0) Introduced on the S6000, S6000–ON, S61000–ON, Z9100–ON. Usage Information The xoff-state threshold polling-count command is used to set the number of times the polling should be done. If a port/priority remains in the ‘xoff’ state for the configured threshold number of polling-intervals, then it would be detected as PFC storm condition. The ‘xoff’ state means no transmission of data happens out of a port/queue even though there are packets buffered in that queue.
PAGE 1503
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6000, S6000–ON, S61000–ON, Z9100–ON. Usage Information The storm-control pfc in queue-drop command is used to drop the traffic meant for egressing through the specified port or priority where PFC storm has been detected.
PAGE 1504
Defaults 10 Command Modes CONFIGURATION (conf-storm-control-pfc) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6000, S6000–ON, S61000–ON, Z9100–ON.
PAGE 1505
Command Modes EXEC Privilege. Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Comma Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6000, S6000–ON, S6100–ON, Z9100–ON. Usage Information The show storm-control pfc status command is used to view the status of the PFC storm on the specified stack u and the port set.
PAGE 1506
Te 0/3 Te 0/4 Te 0/5 Te 0/80 6 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 2 2 2 2 2 2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Dell# show storm-control broadcast Display the storm control broadcast configuration.
PAGE 1507
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced on the E-Series. show storm-control multicast Display the storm control multicast configuration.
PAGE 1508
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on the E-Series. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series.
PAGE 1509
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1510
Command Modes CONFIGURATION (conf) Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1511
Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added the percentage decimal value option. 6.5.1.
PAGE 1512
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-MUX (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. Broadcast traffic (all 0xFs) should be counted against the broadcast storm control meter, not against the multicast storm control meter.
PAGE 1513
storm-control unknown-unicast (Configuration) Configure the percentage of unknown-unicast traffic allowed in or out of the network. Syntax storm-control unknown-unicast [packets_per_second in] To disable storm control for unknown-unicast traffic, use the no storm-control unknown-unicast [packets_per_second in] command. Parameters packets_per_secon d in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368.
PAGE 1514
To disable unknown-unicast storm control on the interface, use the no storm-control unknown-unicast [percentage decimal_value in] | [wred-profile name]] [packets_per_second in] command. Parameters percentage decimal_value [in | out] E-Series Only: Enter the percentage of broadcast traffic allowed in or out of the network. Optionally, you can designate a decimal value percentage, for example, 55.5%. The percentage is from 0 to 100: • 0% blocks all related traffic.
PAGE 1515
52 Spanning Tree Protocol (STP) The commands in this section configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell Networking switch/routing platform. Topics: • bridge-priority • bpdu-destination-mac-address • debug spanning-tree • description • disable • forward-delay • hello-time • max-age • protocol spanning-tree • show config • show spanning-tree 0 • spanning-tree bridge-priority Set the bridge priority of the switch in an IEEE 802.
PAGE 1516
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1517
Version Description 8.2.1.0 Introduced on the C-Series and S-Series. debug spanning-tree Enable debugging of the spanning tree protocol and view information on the protocol. Syntax debug spanning-tree {stp-id [all | bpdu | config | events | exceptions | general | root] | protocol} To disable debugging, use the no debug spanning-tree command. Parameters stp-id Enter zero (0). The switch supports one spanning tree group with a group ID of 0.
PAGE 1518
Usage Information Related Commands When you enable debug spanning-tree bpdu for multiple interfaces, the software only sends information on BPDUs for the last interface specified. • protocol spanning-tree — enters SPANNING TREE mode on the switch. description Enter a description of the spanning tree. Syntax description {description} To remove the description from the spanning tree, use the no description {description} command.
PAGE 1519
Defaults Enabled (that is, the spanning tree protocol is disabled.) Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1520
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1521
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. • forward-delay — changes the wait time before STP transitions to the Forwarding state. • max-age — changes the wait time before STP refreshes protocol configuration information.
PAGE 1522
Related Commands Version Description 6.2.1.1 Introduced on the E-Series. • forward-delay — changes the wait time before STP transitions to the Forwarding state. • hello-time — changes the time interval between BPDUs. protocol spanning-tree To enable and configure the spanning tree group, enter SPANNING TREE mode. Syntax protocol spanning-tree stp-id To disable the Spanning Tree group, use the no protocol spanning-tree stp-id command. Parameters stp-id Enter zero (0).
PAGE 1523
Related Commands • disable — disables spanning tree group 0. To enable spanning tree group 0, use the no disable command. show config Display the current configuration for the mode. Only non-default values display. Syntax show config Command Modes SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 1524
brief (OPTIONAL) Enter the keyword brief to display a synopsis of the spanning tree group configuration information. guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an STP interface and the current port state. interface interface (OPTIONAL) Enter the keyword interface and the type slot/port of the interface you want displayed. Type slot/port options are the following: • For a port-channel interface, enter the keywords port-channel then the portchannel ID.
PAGE 1525
Usage Information Version Description 6.2.1.1 Introduced on the E-Series. Enable spanning tree group 0 prior to using this command. The following describes the show spanning-tree 0 command shown in the example. Example Field Description “Bridge Identifier...” Lists the bridge priority and the MAC address for this STP bridge. “Configured hello...” Displays the settings for hello time, max age, and forward delay. “We are...” States whether this bridge is the root bridge for the STG.
PAGE 1526
The port is not in the portfast mode Port 27 (TenGigabitEthernet 1/1/2/1) is Forwarding Port path cost 4, Port priority 8, Port Identifier 8.27 Designated root has priority 32768, address 0001.e800.0a56 Designated bridge has priority 32768, address 0001.e800.0a56 Designated port id is 8.
PAGE 1527
spanning-tree Assigns a Layer 2 interface to STP instance 0 and configures a port cost or port priority, or enables loop guard, root guard, or the Portfast feature on the interface. Syntax spanning-tree stp-id {cost cost | {loopguard | rootguard} | portfast [bpduguard [shutdown-on-violation]] | priority priority} To disable Spanning Tree group on an interface, use the no spanning-tree stp-id {cost cost | {loopguard | rootguard} | portfast [bpduguard [shutdown-on-violation]] | priority priority} command.
PAGE 1528
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.1 Introduced the loopguard and rootguard options on the S4810. 8.4.2.1 Introduced the loopguard and rootguard options on the E-Series, C-Series, and SSeries. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the shutdown-on-violation option. 7.7.1.
PAGE 1529
53 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell Networking device. For more information on SmartScripts, see Dell Networking Open Automation guide.
PAGE 1530
Usage Information Example Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. • When you run the command, the system displays a message with the information directing to the URL for further information.
PAGE 1531
Reject the EULA: Dell(conf)#eula-consent support-assist reject Aug 24 22:35:38: %STKUNIT1-M:CP %SUPPORT_ASSIST-6-SUPASSIST_EVT: Event monitor service stopped I do not accept the terms of the license agreement. The SupportAssist feature has been deactivated and can no longer be used. To enable SupportAssist configurations, accept the terms of the license agreement by configuring this command 'eula-consent support-assist accept'.
PAGE 1532
Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.1) Introduced on the S6010-ON and S4048T-ON. 9.10(0.0) Introduced on the S3148. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. You are guided through a series of queries to configure SupportAssist.
PAGE 1533
SupportAssist Commands Dell Networking OS supports the following SupportAssist mode commands. activity Move to the SupportAssist Activity mode for an activity. Allow the user to configure customized details for a specific activity. Syntax activity {activity-name} To remove all customized detail for a specific activity, use the no activity {activity-name} command. Parameters activity-name Enter one of the following keywords: • Enter the keyword full-transfer to enable or disable full transfer.
PAGE 1534
Parameters company-name Enter the name for the company. If there are multiple words in the name, use optional additional fields. company-nextname (OPTIONAL) Enter the next components of the company name, up to 5 components are allowed. Command Modes SUPPORTASSIST Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.11(0.
PAGE 1535
Usage Information Each contact person must be unique by their name. You can configure only one contact person. It is not possible to remove the first name or last name. The no form of the command removes the entire contactperson entry. This command is optional for SupportAssist service configuration. enable Enable all activities and severs for the SupportAssist service. Syntax enable all To disable the SupportAssist activities temporarily, use the no enable all command.
PAGE 1536
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1537
Usage Information Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. The remote file specification for full transfer includes the protocol that is used to copy the file from the remote system. The default Manifest-file for full transfer includes records like alarms, logs, operational, and configuration data. Related Commands • action-manifest install — configure the action-manifest to use for a specific activity.
PAGE 1538
• action-manifest remove — remove the action-manifest file for an activity. action-manifest remove Remove the action-manifest file from Dell Networking OS. Syntax action-manifest remove } Parameters Command Modes local-file-name Enter the name of the local action-manifest file. Allowable characters are: a to z, A to Z, 0 to 9, -, _, and space.
PAGE 1539
Related Commands Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. • action-manifest get — copy an action-manifest file for an activity to the system. • action-manifest install — configure the action-manifest to use for a specific activity.
PAGE 1540
address Configure the address information for the company. Syntax address [city company-city] [{province | region | state} name] [country company-country] [{postalcode | zipcode] company-code] To remove a portion of the company address information, use the no address [city | province | region | state | country | postalcode | zipcode] command. For example, to remove the city alone, use the no address city command. To remove the complete company contact information, use the no address command.
PAGE 1541
street-address Configure the street address information for the company. Syntax street-address {address1} [address2]…[address8] To remove the street address, use the no street-address command. Parameters address1 Enter the street address for the company. address2..address8 (OPTIONAL) Enter the street address of the company site. Up to 8 fields are allowed. Command Modes SUPPORTASSIST COMPANY Command History This guide is platform-specific.
PAGE 1542
SupportAssist Person Commands Dell Networking OS supports the following SupportAssist Person mode commands. email-address Configure the email addresses to reach the contact person. Syntax email-address primary email-address [alternate email-address] To remove an email address, use the no email-address command. To remove the primary and the alternate email addresses, use the no email-address primary and no email-address alternate commands respectively.
PAGE 1543
Parameters primary phone Enter the keyword primary then the primary phone number for the person. alternate phone Enter the keyword alternate then the alternate phone number for the person. Command Modes SUPPORTASSIST PERSON Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.
PAGE 1544
• phone — configure phone numbers to reach the contact person. time-zone Configure the time zone for contacting the person. Syntax time-zone zone +-HH:MM[start-time HH:MM] [end-time HH:MM] To remove the time zone, use the no time-zone [zone | start-time | end-time] command. Parameters zone +-HH:MM Enter the keyword zone then a time difference from GMT expressed as HH:MM. This number may be preceded by either a + or – sign.
PAGE 1545
NOTE: The :: notation specifies successive hexadecimal fields of zeros. NOTE: To use the IPv6 address, the Open Automation package should also support IPv6 communications. For this purpose, SupportAssist requires Dell Networking Open Automation 9.10(0.0) package or later. port port-number Enter the keyword port then the TCP/IP port number. The port number range is from 80 to 100000. username userid (OPTIONAL) Enter the keyword username then the user ID used for the proxy server.
PAGE 1546
Related Commands Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. • server — configure the name of the remote SupportAssist server. url Configure the URL to reach the SupportAssist remote server. Syntax url uniform-resource-locator To delete the URL for the server, use the no url command.
PAGE 1547
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1548
show running-config Display the current configuration and changes from the default values. Syntax show running-config support-assist Parameters support-assist Enter the keyword support-assist to view the detailed configuration for the feature. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.11(0.
PAGE 1549
Command History Example This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced on the M I/O Aggregator and FN IOM. 9.10(0.0) Introduced on the C9010, Z9100–ON, S6100–ON, and S3100 series. 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1550
54 System Time and Date The commands in this section configure time values on the system, either using the Dell Networking OS, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, see “Network Time Protocol” of the Management section in the Dell Networking OS Configuration Guide.
PAGE 1551
start-day Enter the number of the day. The range is from 1 to 31. You can enter the name of a month to change the order of the display to time day month year. start-year Enter a four-digit number as the year. The range is from 1993 to 2035. start-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm. end-day Enter the number of the day. The range is from 1 to 31.
PAGE 1552
clock summer-time recurring Set the software clock to convert to daylight saving time on a specific day each year. Syntax clock summer-time time-zone recurring [start-week start-day start-month starttime end-week end-day end-month end-time [offset]] To delete a daylight saving time zone configuration, use the no clock summer-time command. Parameters time-zone Enter the three-letter name for the time zone. This name is displayed in the show clock output. You can enter up to eight characters.
PAGE 1553
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 1554
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1555
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1556
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. You also must configure an authentication key for NTP traffic using the ntp authentication-key command. ntp broadcast client Set up the interface to receive NTP broadcasts from an NTP server. Syntax ntp broadcast client To disable broadcast, use the no ntp broadcast client command.
PAGE 1557
ntp disable Prevent an interface from receiving NTP packets. Syntax ntp disable To re-enable NTP on an interface, use the no ntp disable command. Defaults Disabled (that is, if you configure an NTP host, all interfaces receive NTP packets) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 1558
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.
PAGE 1559
ntp offset-threshold Configure the threshold time interval before which the system generates an NTP audit log message if the time difference from the NTP server is greater than a threshold value (offset-threshold). Syntax ntp offset-threshold threshold-value To disable the threshold value, use the no ntp offset-threshold command. Parameters offset-threshold threshold-value (Optional) Enter the keyword offset-threshold and then the threshold value. The range is from 0 to 999. Defaults Not enabled.
PAGE 1560
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added support for VRF. 9.4.(0.0) Added support for VRF. 9.2(1.
PAGE 1561
• For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1562
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1563
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000.
PAGE 1564
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1565
Usage Information Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1566
* master (synced), # master (unsynced), + selected, - candidate Dell# Related Commands • show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXECEXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.
PAGE 1567
Usage Information Example Related Commands Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1568
55 Tunneling Tunneling is supported on Dell Networking OS. Topics: • ip unnumbered • ipv6 unnumbered • tunnel allow-remote • tunnel destination • tunnel dscp • tunnel flow-label • tunnel hop-limit • tunnel keepalive • tunnel-mode • tunnel source ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address.
PAGE 1569
Usage Information Version Description 9.4(0.1) Introduced on the S4810, S4820T, S6000 and Z9000. 9.3(0.1) Introduced on the S5000 and Z9000. The ip unnumbered command fails in two conditions: • If the logical ip address is configured. • If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends.
PAGE 1570
• If Tunnel mode is ipv6ip (where ip address over tunnel interface is not possible). To ping the unnumbered tunnels, the logical address route information must be present at both the ends. NOTE: The ipv6 unnumbered command can specify an interface name that does not exist or does not have a configured IPv6 address. The tunnel interface is not changed to operationally up until the logical IP address is identified from one of the address family.
PAGE 1571
If you configure any allow-remote , the tunnel source or tunnel mode commands fail if the outer header address family does not match that of the configured allow-remote. tunnel destination Set a destination endpoint for the tunnel. Syntax tunnel destination {ip-address | ipv6–address} To delete a tunnel destination address, use the no tunnel destination {ip-address | ipv6– address} command. Parameters ip-address Enter the destination IPv4 address for the tunnel.
PAGE 1572
Parameters mapped Enter the keyword mapped to map the original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/Traffic Class (IPv6) depending on the mode of tunnel. value Enter a value to set the DSCP value in the tunnel header. The range is from 0 to 63. The default value of 0 denotes mapping of original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/Traffic Class (IPv6) depending on the mode of tunnel.
PAGE 1573
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. This command is only valid for tunnel interfaces with an IPv6 outer header.
PAGE 1574
tunnel keepalive Configure the tunnel keepalive target, interval and attempts. Syntax tunnel keepalive {ip-address | ipv6-address}[interval {seconds}] [attempts {count | unlimited}] To disable the tunnel keepalive probes use the no tunnel keepalive command. Parameters ip-address ipv6 address Enter the IPv4 or IPv6 address of the peer to which the keepalive probes will be sent.
PAGE 1575
into a keepalive down state that does not clear in a few seconds, then performing shutdown - no shutdown sequence on one end should bring both ends back to up. tunnel-mode Enable a tunnel interface. . Syntax tunnel mode {ipip | ipv6 | ipv6ip}[decapsulate-any] To disable an active tunnel interface, use the no tunnel mode command. Parameters ipip Enable tunnel in RFC 2003 mode and encapsulate IPv4 and/or IPv6 datagrams inside an IPv4 tunnel.
PAGE 1576
tunnel source Set a source address for the tunnel. Syntax tunnel source {ip-address | ipv6–address | interface-type-number | anylocal} To delete the current tunnel source address, use the no tunnel source command. Parameters ip-address Enter the source IPv4 address in A.B.C.D format. ipv6–address Enter the source IPv6 address in X:X:X:X::X format. interface-typenumber • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information.
PAGE 1577
Usage Information Added an optional keyword “anylocal” to the tunnel source command. The anylocal argument can be used in place of the ip address or interface, but only with the multipoint receive-only mode tunnels. The tunnel source anylocal command allows the multipoint receive-only tunnel to decapsulate tunnel packets addressed to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the switch that is operationally Up.
PAGE 1578
56 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link.
PAGE 1579
Command History Related Commands This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50.
PAGE 1580
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • clear ufd-disable — re-enable downstream interfaces that are in a UFD-Disabled Error state. description Enter a text description of an uplink-state group. Syntax description text Parameters text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters.
PAGE 1581
To delete an uplink-state group, enter the no downstream interface command. Parameters interface Enter one of the following interface types: • 10 Gigabit Ethernet: tengigabitethernet {slot/port/subport | slot/ port/subport-range} • 40-Gigabit Ethernet:fortyGigE {slot/port} • Port channel: port-channel {1–128 | port-channel-range} • For a 25-Gigabit interface, enter the keyword twentyfiveGigE then the slot/port/ subport information.
PAGE 1582
downstream auto-recover Enable auto-recovery so that UFD-disabled downstream ports in an uplink-state group automatically come up when a disabled upstream port in the group comes back up. Syntax downstream auto-recover To disable auto-recovery on downstream links, use the no downstream auto-recover command. Defaults The auto-recovery of UFD-disabled downstream ports is enabled. Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific.
PAGE 1583
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.
PAGE 1584
Related Commands Version Description 8.3.19.0 Introduced on the S4820T 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • uplink-state-group — create an uplink-state group and enables the tracking of upstream links. show running-config uplink-state-group Display the current configuration of one or more uplink-state groups.
PAGE 1585
show uplink-state-group Display status information on a specified uplink-state group or all groups. Syntax Parameters Defaults Command Modes Command History show uplink-state-group [group-id] [detail] group-id Displays status information on a specified uplink-state group or all groups. The valid group-id values are from 1 to 16. detail Displays additional status information on the upstream and downstream interfaces in each group none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1586
Parameters group-id Enter the ID number of an uplink-state group. The range is from 1 to 16. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10.0.2 Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1587
To delete an uplink-state group, use the no upstream interface command. Parameters interface Enter one of the following interface types: • 10 Gigabit Ethernet: tengigabitethernet {slot/port/subport | slot/ port/subport-range} • 40-Gigabit Ethernet:fortyGigE {slot/port} • Port channel: port-channel {1–128 | port-channel-range} • For a 25-Gigabit interface, enter the keyword twentyfiveGigE then the slot/port/ subport information.
PAGE 1588
• 1588 uplink-state-group — creates an uplink-state group and enables the tracking of upstream links.
PAGE 1589
57 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell Networking OS supports this feature. For more information about basic VLAN commands, see the Virtual LAN (VLAN) Commands section in Layer 2.
PAGE 1590
dei enable Enable packets to be dropped based on their DEI value. Syntax dei enable Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1591
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command.
PAGE 1592
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. member Assign a stackable VLAN access or trunk port to a VLAN. The VLAN must contain the vlan-stack compatible command in its configuration. Syntax member interface To remove an interface from a Stackable VLAN, use the no member interface command.
PAGE 1593
Usage Information Related Commands Version Description 8.2.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the C-Series and S-Series. Enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. • vlan-stack compatible — enables stackable VLAN on a VLAN. stack-unit stack-group Configure a stacking group specified by an ID.
PAGE 1594
vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network. Syntax vlan-stack access To remove access port designation, use the no vlan-stack access command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 1595
Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1596
vlan-stack dot1p-mapping Map C-Tag dot1p values to an S-Tag dot1p value. Syntax vlan-stack dot1p-mapping c-tag-dot1p values sp-tag-dot1p value Parameters c-tag-dot1p value Enter the keyword c-tag-dot1p then the customer dot1p value that is mapped to a service provider do1p value. The range is from 0 to 7. sp-tag-dot1p value Enter the keyword sp-tag-dot1p then the service provider dot1p value. The range is from 0 to 7.
PAGE 1597
Defaults 0x9100 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1598
To remove a trunk port designation from the selected interface, use the no vlan-stack trunk command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1599
switchport vlan-stack trunk no shutdown Dell(conf-if-te-1/1/2/1)# interface vlan 100 Dell(conf-if-vl-100)# vlan-stack compatible Dell(conf-if-vl-100-stack)# member tengigabitethernet 1/1/2/1 Dell(conf-if-vl-100-stack)# show config ! interface Vlan 100 no ip address vlan-stack compatible member TenGigabitEthernet 1/1/2/1 shutdown Dell(conf-if-vl-100-stack)# interface vlan 20 Dell(conf-if-vl-20)# tagged Tengigabitethernet 1/1/2/1 Dell(conf-if-vl-20)# show config ! interface Vlan 20 no ip address tagged TenGig
PAGE 1600
58 Virtual Routing and Forwarding (VRF) Virtual routing and forwarding (VRF) allows multiple instances of a routing table to coexist on the same router at the same time.
PAGE 1601
Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.0/0) in the LPM route forwarding table if it was deleted using the no ip unknown-unicast command previously. This will be the default configuration after reload.
PAGE 1602
Parameters string Enter a descriptive name for the VRF. Defaults None. Command Modes VRF MODE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 1603
Usage Information You can attach an interface to either a nondefault VRF or a management VRF. To assign a port-back to a default VRF, remove the VRF association from the interface. You can use this only if there is no IP address configured on the interface. There must be no prior Layer 3 configuration on the interface when configuring VRF. You must enable VRF before using this command.
PAGE 1604
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To make the HTTP clients VRF-aware, use the ip http vrf command.
PAGE 1605
Usage Information To export all the routes corresponding to a source VRF, you can use the ip route-export tag command without specifying the route-map attribute. This action exposes source VRF routes to various other VRFs, which then import these routes using the ip route-import tag command. In Dell Networking OS, you can configure one route-export per VRF as you can only expose one set of routes for leaking.
PAGE 1606
Usage Information Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match protocol and match prefix-list options. Other options that are configured in the route-maps are ignored. Related Commands • ip route-export – exports routes to another VRF. ipv6 route-export Enables route leaking between VRFs.
PAGE 1607
In Dell Networking OS, you can configure one route-export per VRF as you can only expose one set of routes for leaking. However, you can configure multiple route-import targets because a VRF can accept routes from multiple VRFs. You can expose a unique set of routes from the source VRF for leaking to other VRFs. When two VRFs leak or export routes, there is no option to discretely filter leaked routes from each source VRF.
PAGE 1608
The export-target and import-target support only the match the protocol and prefix-list options. Other options that you configure in the route-maps are ignored. Related Commands • ipv6 route-export — exports IPv6 routes to another VRF. match source-protocol Specify matching source-protocol criteria while exporting or importing routes. Syntax match source-protocol {bgp | isis | ospf | connected | static} Parameters bgp Enter the keyword bgp to leak or share routes corresponding to the BGP protocol.
PAGE 1609
Parameters imported-bgp Enter the keywords imported-bgp to redistribute leaked routes that are learned using the BGP protocol. imported-ospf Enter the keywords imported-ospf to redistribute leaked routes that are learned using the OSPF protocol. imported-isis Enter the keywords imported-isis to redistribute leaked routes that are learned using the ISIS protocol. route-map Enter the name of the route-map to specify the filtering criteria for imported routes.
PAGE 1610
Usage Information Version Description 9.4.(0.0) Introduced on the S-Series and Z9000. When you use this command, the management ports corresponding to both the active unit and the standby unit are associated with the management VRF. maximum dynamic-routes Specify the maximum number of dynamic (protocol) routes a VRF can have.
PAGE 1611
show ip vrf Displays information corresponding to the VRFs that you configure in the system. Syntax Parameters Command Modes Command History show ip [vrf vrf-name] vrf vrf-name • EXEC • EXEC Privilege Enter the keyword vrf then the name of the VRF to display information corresponding to that VRF. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1612
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON and Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. Usage Information This command displays information from the running-config corresponding to either a specific VRF or all the VRFs in the system.
PAGE 1613
59 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Dell Networking OS Command Line Reference Guide.
PAGE 1614
3 Example The proxy-gateway LLDP configuration is applied. Dell(conf)# vlt-domain 1 Dell(conf-vlt-domain)# proxy-gateway lldp Dell(conf-vlt-domain)# proxy-gateway static Enables the proxy-gateway feature using static configurations. Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1615
mac-address Enter the 48-bit hexadecimal address in nn:nn:nn:nn:nn:nn format. vlan-range Enter the VLAN IDs in which proxy gateway is not needed. The VLANs are excluded from doing proxy gateway. The value can be a single VLAN ID, comma-separated VLAN IDs, a range of VLAN IDs, or a combination. For example: Comma-separated: 3, 4, 6 Range: 5-10 Combination: 3, 4, 5-10, 8 Command Modes VLT DOMAIN PROXY GW STATIC Command History This guide is platform-specific.
PAGE 1616
vlan-range Enter the VLAN IDs that you want to exclude from the proxy gateway. The value can be a single VLAN ID, comma-separated VLAN IDs, a range of VLAN IDs, or a combination. For example: Comma-separated: 3, 4, 6 Range: 5-10 Combination: 3, 4, 5-10, 8 Command Modes VLT DOMAIN PROXY GW LLDP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.
PAGE 1617
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Removed the default value on the S-Series and Z-Series. 9.4(0.
PAGE 1618
This configuration is applicable only for an LLDP proxy gateway. A typical use example is a square VLT topology with single link connecting to the remote peers. Example Dell(conf-vlt-domain-proxy-gw-lldp)# vlt-peer-mac transmit show vlt-proxy-gateway Displays the VLT proxy gateway configuration.
PAGE 1619
Example Dell#show vlt proxy-gateway VLT Proxy Gateway Brief ------------------------Config Mode: Global LLDP Config Status: peer-mac-transmit Status: LLDP Enabled Disabled Dell#show vlt proxy-gateway info static Mac Address Exclude Vlan ---------------------00:01:e8:8a:e8:f7 3,7-8 00:01:e8:8b:1c:c0 3,7-8 Dell#show vlt proxy-gateway info lldp LagId Mac Address Exclude Vlan ----- ---------------------Po 55 00:01:e8:8a:e8:f7 3,7-8 << Macs learnt via port-channel 55 Po 55 00:01:e8:8b:1c:c0 3,7-8 VLT Proxy G
PAGE 1620
60 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1621
• show vlt role • show vlt statistics • show vlt statistics igmp-snoop • unit-id • vlt domain • vlt-peer-lag port-channel back-up destination Configure the IPv4 or IPv6 address of the management interface on the remote VLT peer used as the VLT backup link endpoint for sending out-of-band (OOB) hello messages. Syntax Parameters back-up destination {[ipv4–address] | [ipv6 ipv6–address] [interval seconds]} ipv4–address Enter the IPv4 address of the backup destination.
PAGE 1622
clear vlt statistics Clear the VLT operation statistics. Syntax clear vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Clear the VLT statistics for the domain. multicast Clear the VLT statistics for multicast. mac Clear the VLT statistics for the MAC address. arp Clear the VLT statistics for ARP. igmp-snoop Clear the VLT statistics for IGMP snooping. ndp Clear the VLT statistics for NDP. Command Modes EXEC Command History This guide is platform-specific.
PAGE 1623
delay-restore Configure the delay in bringing up VLT ports after reload or peer-link restoration between the VLT peer switches. Syntax Parameters delay-restore delay-restore Enter the amount of time, in seconds, to delay bringing up the VLT ports after the VLTi device reloads or after the peer-link restores between VLT peer switches. The range from 1 to 1200. The default is 90 seconds. Defaults Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1624
To remove the boot up timer value, use the no delay-restore abort-threshold command. Parameters interval Enter the interval value (in seconds) for the delay restore timer to abort. The range is from 1 to 1800 seconds. The default is 60 seconds. This delay restore timer applies only during reload/boot-up and not in other scenarios (for example, during ICL flap). Defaults 60 seconds Command Modes VLT DOMAIN Command History This guide is platform-specific.
PAGE 1625
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added port-channel parameter on the S4810. 8.3.8.0 Introduced on the S4810.
PAGE 1626
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. peer-link port-channel Configure the specified port channel as the chassis interconnect trunk between VLT peers in the domain.
PAGE 1627
Usage Information To configure the VLAN from where the VLT peer forwards packets received over the VLTi from an adjacent VLT peer that is down, use the peer-down-vlan option. When a VLT peer with bare metal provisioning (BMP) is booting up, it sends untagged DHCP discover packets to its peer over the VLTi. To ensure that the DHCP discover packets are forwarded to the VLAN that has the DHCP server, use this configuration. peer-routing Enable Layer 3 (L3) VLT peer-routing.
PAGE 1628
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for default value on the S-Series and Z-Series. 9.5(0.1) Introduced on the Z9500.
PAGE 1629
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. After you configure a VLT domain on each peer switch and connect (cable) the two VLT peers on each side of the VLT interconnect, the system elects a primary and secondary VLT peer device. To configure the primary and secondary roles before the election process, use the primary-priority command.
PAGE 1630
Version : Local System MAC address : Remote System MAC address : Remote system version : Delay-Restore timer : Delay-Restore Abort Threshold : Peer-Routing : Peer-Routing-Timeout timer : Multicast peer-routing timeout: Dell# 6(3) 00:01:e8:8a:e9:91 00:01:e8:8a:e9:76 6(3) 90 seconds 60 seconds Disabled 0 seconds 150 seconds show vlt backup-link Displays information about the backup link operation. Syntax show vlt backup-link Default Not configured.
PAGE 1631
show vlt counters Displays counter information. Syntax Parameters show vlt counters [arp| igmp-snoop | interface | mac | ndp] arp Enter the keyword arp to display the ARP counter information for the VLT. igmp-snoop Enter the keywords igmp-snoop to display the igmp-snooping counter information for the VLT. interface Enter the keyword interface to display the interface counter information for the VLT. mac Enter the keyword mac to display the MAC address counter information for the VLT.
PAGE 1632
Example (igmpsnoop interface port-channel) Dell#show vlt counter igmp-snoop interface port-channel 2 VLT Port-ID: 2 IGMP Counter ----------------------IGMP MRouter Vlans count : 0 IGMP Mcast Groups count : 5 Dell# show vlt counter igmp-snoop interface port-channel 100 VLT Port-ID: 100 IGMP Counter ----------------------IGMP MRouter Vlans count : 1 IGMP Mcast Groups count : 0 Ve Example (NDP and Non-VLT ARP) Dell#show vlt counters Total VLT Counters ------------------L2 Total MAC-Address Count: Total Arp
PAGE 1633
Example Dell# Dell(conf-if-vl-100)#show vlt detail Local LAG Id Peer LAG Id Local Status Peer Status Active VLANs ------------ ----------- ------------ ----------- ------------10 10 UP UP 100, 200, 300, 400, show vlt inconsistency Display run-time inconsistencies in the incoming interface (IIF) for spanned multicast routes (mroutes). Syntax show vlt inconsistency ip mroute Command Modes EXEC Command History This guide is platform-specific.
PAGE 1634
Example Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced support for Q-in-Q implementation over VLT on the S-Series and Z-Series. Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000.
PAGE 1635
------128 ----mt ---mu Vlan-stack protocol-type -----------------------Local ----0x4100 Peer ---0x8100 VLT-VLAN config --------------Local Lag --------128 Peer Lag Local VLANs -------- ----------128 4094 Peer VLANs ---------100 Dell# show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. Syntax show vlt role Default Not configured.
PAGE 1636
Dell_VLTpeer2# show vlt role VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 show vlt statistics Displays VLT operations statistics. Syntax show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters arp Enter the keyword arp to display the ARP VLT statistics. domain Enter the keyword domain to display the domain VLT statistics.
PAGE 1637
Example NOTE: The following example shows the statistics for all the VLT parameters. If you enter a specific keyword, such as mac, only the statistics for that VLT parameter displays.
PAGE 1638
show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1639
Command History Usage Information This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.
PAGE 1640
Usage Information Related Commands Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. The VLT domain ID must be the same between the two VLT devices. If the domain ID is not the same, a syslog message generates and VLT does not launch. • show vlt brief — display the delay-restore value. vlt-peer-lag port-channel Associate the port channel to the corresponding VLT peer port channel for the VLT connection to an attached device.
PAGE 1641
61 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on Dell Networking OS.
PAGE 1642
Version Description 9.4.(0.0) Introduced on the S6000. Usage Information You must configure feature VXLAN to configure VXLAN-instance. Related Commands vxlan-instance — Enable VXLAN Instance configuration on the platform. debug vxlan Debug messages between the Gateway and Controller. Syntax debug vxlan Defaults Disabled Command Modes EXEC Privilege Command History Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1643
Related Commands Version Description 9.4.(0.0) Introduced on the S6000. vxlan-instance— Enable VXLAN Instance configuration on the platform. vxlan-instance Enable VXLAN Instance configuration on the platform. Syntax vxlan-instance instance ID To delete vxlan-instance from the system, use no vxlan-instance instance ID command. Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release.
PAGE 1644
To unconfigure VAP, use the no vxlan-instance 1 command. Parameters instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Defaults Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.
PAGE 1645
gateway-ip Configures gateway IP address on the platform. Syntax Parameters gateway-ip IP address IP address Enter the IP address of the gateway for the VXLAN instance. Defaults Disabled Command Modes VXLAN INSTANCE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON.
PAGE 1646
Related Commands Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000. vxlan-instance — Enable VXLAN instance configuration on the platform. show vxlan vxlan-instance Displays information related to Network Virtualization Overlay (NVO) Gateway.
PAGE 1647
Port List Fo 1/4/1 Related Commands : Te 1/1/1/1 Te 1/1/2/1 Po 2 vxlan-instance- Enable VXLAN Instance configuration on the platform. show running-config vxlan Displays the VXLAN configuration information from running configuration. Syntax Command Modes Command History Example show running-config vxlan • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1648
show vxlan vxlan-instance unicast-mac-remote Displays the information of the remote unicast MACs associated with the logical network related to Network Virtualization Overlay (NVO) Gateway. Syntax show vxlan vxlan-instance instance ID unicast-mac-remote [logical-network name | vnid VNID] Parameters Command Modes Command History instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release.
PAGE 1649
Parameters Command Modes Command History Example instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. name (Optional) Enter the name of VXLAN logical network with a maximum length of 30 characters. vnid VNID (Optional) Enter the keyword vnid and enter the ID of the VXLAN. The range is from 1 to 16777215. • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1650
VLAN-ID Defaults • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information. • For a 50-Gigabit Ethernet interface, enter the keyword fiftyGigE then the stack/ slot/port/subport information. • For a 100-Gigabit Ethernet interface, enter the keyword hundredGigE then the stack/slot/port information.
PAGE 1651
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.11(0.0) Introduced the static mode on the S4048–ON, S4048T-ON, S6000–ON, S6010–ON, S6100–ON, and Z9100–ON. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0) Introduced on the S4048–ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S6000.
PAGE 1652
Example Version Description 9.4.(0.0) Introduced on the S6000. Dell#show vxlan vxlan-instance 1 logical-network name LN-1 Name : LN-1 Description : Type : ELAN Tunnel Key : 1 VFI : 28674 Unknown Multicast MAC Tunnels: 2.2.2.
PAGE 1653
clear mac-address-table dynamic all Clear the MAC address table of all MAC address learned dynamically. It clears both MAC address of the VXLAN and legacy VLAN. Syntax Parameters clear mac-address-table dynamic all instance ID Enter the VXLAN instance ID. The platform supports only the instance ID 1 in the initial release. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1654
62 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell Networking OS. Topics: • IPv4 VRRP Commands • IPv6 VRRP Commands IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds.
PAGE 1655
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges.
PAGE 1656
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations.
PAGE 1657
Version Description 6.2.1.1 Introduced on the E-Series. Usage Information NOTE: This command also enables you to clear the port configurations corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 1658
state Enter the keyword state to enable debugging of VRRP state changes. timer Enter the keyword timer to enable debugging of the VRRP timer. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1659
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. disable Disable a VRRP group. Syntax disable To re-enable a disabled VRRP group, use the no disable command.
PAGE 1660
Usage Information Related Commands To enable VRRP traffic, assign an IP address to the VRRP group using the virtual-address command and enter no disable. • virtual-address — specify the IP address of the virtual router. hold-time Specify a delay (in seconds) before a switch becomes the MASTER virtual router. By delaying the initialization of the VRRP MASTER, the new switch can stabilize its routing tables.
PAGE 1661
Related Commands • disable — disables a VRRP group. preempt To preempt or become the MASTER router, configure a BACKUP router with a higher priority value. Syntax preempt To prohibit preemption, use the no preempt command. Defaults Enabled (that is, a BACKUP router can preempt the MASTER router). Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1662
Defaults 100 Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 1663
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell(conf-if-vrid-4)# show config vrrp-group 4 virtual-address 119.
PAGE 1664
• Command Modes Command History Usage Information ipv6 (OPTIONAL) Enter the keyword ipv6 to view only VRRP IPv6 groups. vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view active VRRP groups corresponding to that VRF. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.
PAGE 1665
Item Description • NA/IF (the interface is not available). • MASTER (the interface associated with the MASTER router). • BACKUP (the interface associated with the BACKUP router). Master addr Displays the IP address of the MASTER router. Virtual addr(s) Displays the virtual IP addresses of the VRRP routers associated with the interface.
PAGE 1666
Item Description • Dn or Up states whether the interface is down or up. • The interface type slot/port information. Example Dell> show vrrp -----------------TenGigabitEthernet 1/1/2/1, VRID: 1, Net: 10.1.1.253 VRF: 0 default State: Master, Priority: 105, Master: 10.1.1.253 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Adv sent: 1862, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.
PAGE 1667
Parameters interface priority-cost (OPTIONAL) Enter the following keywords and the interface information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information.
PAGE 1668
To delete one or more virtual IP addresses, use the no virtual-address ip-address1 [... ipaddress12] command. Parameters ip-address1 Enter an IP address of the virtual router in dotted decimal format. The IP address must be on the same subnet as the interface’s primary IP address. ... ip-address12 (OPTIONAL) Enter up to 11 additional IP addresses of virtual routers in dotted decimal format. Separate the IP addresses with a space.
PAGE 1669
Parameters seconds Enter the number of seconds for the delay for VRRP initialization after an interface becomes operational. The range is from 0 to 900 (0 indicates no delay). Defaults 0 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Related Command Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1670
Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. This command applies to all the VRRP interfaces on a system. When you use this command with the vrrp delay minimum command, the later timer rules VRRP enabling.
PAGE 1671
Usage Information Related Command Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The VRRP group only becomes active and sends VRRP packets when you configure a virtual IP address. When you delete the virtual IP address, the VRRP group stops sending VRRP packets.
PAGE 1672
Usage Information You can use the both command to migrate from VRRPv2 to VRRPv3. When you set the VRRP protocol version to both, the switch sends only VRRPv3 advertisements but can receive either VRRPv2 or VRRPv3 packets. To migrate an IPv4 VRRP group from VRRPv2 to VRRPv3: 1 Set the switches with the lowest priority to both. 2 Set the switch with the highest priority to version 3. 3 Set all the switches from both to version 3.
PAGE 1673
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version Description 9.9(0.0) Added support to clear the interface configurations corresponding to a range of ports. 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1674
• For a Port Channel interface, enter the keywords port-channel, and then a number. • For a VLAN interface, enter the keyword vlan, and then the VLAN ID. The VLAN ID range is from 1 to 4094. vrid (OPTIONAL) Enter a number from 1 to 255 as the VRRP group ID. all Enter the keyword all to enable debugging of all VRRP groups. bfd Enter the keyword bfd to enable debugging of all VFFP BFD interactions.
PAGE 1675
Command Modes Command History Usage Information • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the stack/slot/port/subport information. • For a 25-Gigabit Ethernet interface, enter the keyword twentyFiveGigE then the stack/slot/port/subport information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the stack/ slot/port[/subport] information.
PAGE 1676
Line starting with Description • backup (BACKUP virtual router) Also displays the interface’s priority and IP address of the MASTER. Hold Down:... Adv rcvd:... Example Displays additional VRRP configuration information: • Hold Down displays the hold down timer interval in seconds. • Preempt displays TRUE if preempt is configured and FALSE if preempt is not configured. • AdvInt displays the Advertise Interval in seconds.
PAGE 1677
Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.10(0.0) Introduced on the S6100–ON. 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.4.2.