Users Guide

Viewing the Details of Organizational Specic Unrecognized LLDP TLVs
• To view the information of organizational specic unrecognized LLDP TLVs using SNMP, use the following commands.
snmpwalk -v2c -c public 10.16.150.83 1.0.8802.1.1.2.1.4.4.1.4
iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.1.133 = STRING: "Dell"
iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.2.134 = STRING: "Dell"
iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.3.135 = STRING: "Dell"
iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.4.136 = STRING: "Dell"
iso.0.8802.1.1.2.1.4.4.1.4.0.3161092.1.0.1.102.5.137 = STRING: "Dell"
snmpget -v2c -c public 10.16.150.102 1.0.8802.1.1.2.1.4.4.1.4.0.1048580.2.0.1.232.16.1
iso.0.8802.1.1.2.1.4.4.1.4.0.1048580.2.0.1.232.16.1 = STRING: "A"
MIB Support for CAM
Dell EMC Networking provides a method to retrieve the CAM usage information. The following table lists the related MIB objects:
Table 116. MIB Objects for CAM
MIB Object OID Description
camUsageL2Pip
eLine
1.3.6.1.4.1.6027.3.7.1.1.2.1.11 Contains information about the pipe line number of the
chip on the layer 2 switch where CAM is located.
camUsageL3Pip
eLine
1.3.6.1.4.1.6027.3.7.1.1.3.1.19 Contains information about the pipe line number of the
chip on the layer 3 switch where CAM is located.
camUsageL3Ing
QosUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.12.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 ingress QOS.
camUsageL3Ing
AclUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.16.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 ingress ACL.
camUsageL3Eg
rAclUsed
1.3.6.1.4.1.6027.3.7.1.1.3.1.18.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 3 egress ACL.
camUsageL2Ing
AclUsed
1.3.6.1.4.1.6027.3.7.1.1.2.1.4.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 2 ingress ACL.
camUsageL2Eg
rAclUsed
1.3.6.1.4.1.6027.3.7.1.1.2.1.10.stack-unit.port-pipe.pipe-line Contains information about the total CAM size allocated to
layer 2 egress ACL.
NOTE: The last three digits of these OIDs correspond to the stack-unit, port-pipe, and pipe-line respectively. The values
corresponding to these elds are incremented by one before being displayed in the snmp walk output. As a result, the stack-unit
number, the port-pipe number, and the pipe-line number starts from 1 instead of 0.
Viewing the CAM MIB
• To view the CAM MIB generated by the system, use the following commands.
snmpwalk -c public -v 2c 10.16.133.177 1.3.6.1.4.1.6027.3.7.1.1.3.1.12
SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.12.1.1.1 = INTEGER: 0
SNMPv2-SMI::enterprises.6027.3.7.1.1.3.1.12.1.1.2 = INTEGER: 0
924
Simple Network Management Protocol (SNMP)