Administrator Guide

• ipv4mirracl: 0
l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 0 to 8
in multiples of 2.
ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4 ACL. The range
is from 0 to 9 in multiples of 3, when ipv4udfenable is selected. If not enabled, it is in
multiples of 2. If the feature acloptimized command is enabled, the allocation is in
multiples of 1.
ipv6acl number Enter the keyword ipv6acl and then the number of FP blocks for IPv6 ACL. The range
is from 0 to 9 in multiples of 3. If you used the feature ipv6acloptimized
command, the range is from 0 to 8 in multiples of 2.
ipv4qos number Enter the keyword ipv4qos and then the number of FP blocks for IPv4 QoS. The range
is from 0 to 8 in multiples of 2.
l2qos number Enter the keyword l2qos and then the number of FP blocks for L2 QoS. The range is
from 0 to 8 in multiples of 2.
l2pt number Enter the keyword l2pt and then the number of FP blocks for l2 protocol tunnelling. The
range is from 0 to 8 in multiples of 2.
Ipmacacl number Enter the keyword ipmacacl and then the number of FP blocks for IP and MAC ACL.
The range is from 0 to 9.
etsacl number Enter the keyword etsacl and then the number of FP blocks for ETS ACL. The range is
from 0 to 9.
nlbclusteracl
number
Enter the keyword nlbclusteracl and then the number of FP blocks for nlbcluster
ACL. The range is from 0 to 9. By default, the value is 0 and it supports 8 NLB arp entries
reserved for internal functionality.
NOTE: When you reconfigure CAM allocation, use the nlbclusteracl
number command to change the number of NLB ARP entries. The range is
from 0 to 9. The default value is 0. At the default value of 0, eight NLB ARP
entries are available for use. This platform supports up to 512 CAM entries.
Select 1 to configure 256 entries. Select 2 to configure 512 entries. Even
though you can perform CAM carving to allocate the maximum number of
NLB entries, Dell EMC Networking recommends that you use a maximum of
64 NLB ARP entries.
vman-qos Enter the keyword vman-qos and then the number of FP blocks for VMAN QoS. The
range is from 0 to 9.
Ipv4pbr number Enter the keyword ipv4pbr and then the number of FP blocks for ipv4pbr ACL. The
range is from 0 to 8.Each PBR entry is carved out in double wide mode. While carving,
specify only even groups for PBR.
Openflow number Enter the keyword openflow and then the number of FP blocks for open flow. The
range is from 0 to 9 in multiples of 3.
fcoeacl number Enter the keyword fcoeacl and then the number of FP blocks for FCOE ACL. The
range is from 0 to 8 in multiples of 2.
Iscsioptacl
number
Enter the keyword iscsioptacl and then the number of FP blocks for iSCSI
optimization ACL. The range is from 0 to 9.
ipv4udfmirracl
Enter the keyword ipv4udfmirracl and then the number of FP blocks for IPv4 UDF
and IPv6 mirror ACL. The range is from 0 to 8.
ipv4mirracl
Enter the ipv4mirracl keyword and then the number of FP blocks for IPv4 mirror
ACL. The range is from 0 to 8. You cannot use the ipv4mirracl and
ipv4udfmirracl commands at the same time.
Command Modes CONFIGURATION
438 Content Addressable Memory (CAM)