Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM 下記の情報は、参照されているデバイスの製造業者によって提供されており、Dell によって独自に検証されておらず、 下記の制限事項および免責事項の対象になります。 概要 テープ・ドライブのセットアップ テープ・ドライブの使用 テープ・バックアップ・ソフトウェアの使用 トラブルシューティング 仕様 用語集 注: 「注」は、システムをよりよく活用するために役立つ重要な情報を示します。 注意: 「注意」は、ハードウェアを損傷する、またはデータを失う可能性が想定されることを示し、問題を回避する方法を説明します。 警 告: 「 警 告 」は、 物 的 損 害を生じ る、あるいは「 怪 我 」 、や「 人が障 害を負う」ま た は「 死 亡を も た ら す」 可 能 性があることをを示し ま す。 Information in this document is subject to change without notice. © 2005 Dell Inc. All rights reserved.
目次ページへ戻る 用語集: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM -A-B-C -D-E-F-G-H-I-J-L-M-N-O-P -R-S-T-U-V-W 数値 2:1 圧縮 (2:1 compression). 圧縮して保管できるデータ量と、圧縮なしで保管できるデータ量との関係。2:1 圧縮は、圧縮なしで保管するデータ量に比べ、圧縮したほうが 2 倍の量のデータを 保管できることを表す。 A A. ア ン ペ ア (ampere) を参照。 ア ン ペ ア (A) (ampere (A)). 1 クーロン (C)/秒、または 1 オームの抵抗に 1 ボルトの電圧が加えられて生じる電流の計測単位。 ア ダ プ タ ー (adapter). ア ダ プ タ ー ・ カ ー ド (adapter card) を参照。 ア ダ プ タ ー ・ カ ー ド (adapter card). コンピューターに機能を加える回路ボード。 B バ ッ ク ア ッ プ (backups).
デ ー タ圧縮 (data compression). 圧縮 (compression) を参照。 デ ー タ転送 速 度 (data transfer rate). データ伝送システム内の対応する装置の間で、一定時間当たりに渡されるビット、文字、またはブロックの平均数。速度は、秒、分、または時間当たりの、 ビット、文字、またはブロックで表される。 DC. 直 流 (direct current) を参照。 消 磁 (degauss). テープの磁気を中性化する電流を出す電気コイルに対して、テープを露出して磁気を消すこと。 デ バ イ ス (device). テープ・ドライブやテープ・ライブラリーなどの、データを送受信することができるハードウェア・コンポーネントや周辺装置。 デ バ イ ス ・ ド ラ イ バ ー (device driver). 接続デバイスを使用するのに必要なファームウェアが含まれているファイル。 診断プ ロ グ ラ ム (diagnostic).
ホ ス ト (host). データ通信構成における制御システム、または最高レベル・システム。 サーバー (server) と同義。 I ID. 識別子 (Identifier)。 in. イ ン チ (inch) を参照。 イ ン チ (inch). 1/36 ヤードまたは 25.4 mm と同等の長さの単位。 入 出 力 (I/O) (input/output (I/O)). コンピューターに提供されるデータ、またはコンピューター処理の結果によるデータ。 挿入ガ イ ド (insertion guide). ユーザーがカートリッジを誤って挿入することを防ぐ、テープ・カートリッジの表面にある大きな切り込みの入った個所。 イ ン ス ト ー ル、 取り付け (install). (1) 使用または保守のためにセットアップすること。 (2) 単一の変更によって、あるいは複数のコンポーネントやデバイスの追加によって、サーバーやデバイスに 製品、機構、または機能を追加する処置。 変換コ ネ ク タ ー (interposer).
メ ガ バ イ ト (MB) (megabyte (MB)). 1,000,000 バイト。 N ネ ッ ト ワ ー ク (network). 情報交換のために接続される、データ処理デバイスとソフトウェアの構成。 O エ ー ル ス テ ッ ド (oersted). 有理化されていないセンチメートル - グラム - 秒 (cgs) 電磁気システムにおける磁気フィールドの強さの単位。エールステッドは、軸の長さ 4 パイ・センチメートルごとに 1 アブアンペアの巻きのリニア電流密度で誘発される、細長い均一巻きのソレノイド内部の磁場の強さ。 オ フ ラ イ ン (offline). サーバーのアプリケーションがテープ・ドライブと対話できないときに、テープ・ドライブが入っている操作状態。 オンライン (online). サーバーのアプリケーションがテープ・ドライブと対話できるときに、テープ・ドライブが入っている操作状態。 オ ー プ ン ・ シ ス テ ム (Open Systems).
SCSI ID コ ネ ク タ ー (SCSI ID connector). テープ・ドライブの背面にあり、ドライブの SCSI アドレスをセットできるコネクター。アドレスは、ピン上のジャンパーの配置によって決定される。 SCSI イ ン タ ー フ ェ ー ス (SCSI interface). Small Computer Systems Interface を参照。 SCSI ログ・センス・データ (SCSI log sense data). テープ・ドライブのエラー・ログおよびカウンターに関するサーバーからの照会に対する応答の際に、エラーに関する情報を含み、ドライブに よってサーバーに戻される SCSI センス・バイトのパケット。ログ・センス・データは、特に再現性のない問題の診断に使用される。 秒 (second). 1 分の 1/60。 セ ン ス ・ デ ー タ (sense data). 入出力エラーを記述するデータ。センス・データは、センス入出力コマンドへの応答の際にサーバーに渡される。 サ ー バ ー (server).
間の電気的な電位差であると正式に定義されている。 W 最 大湿球温度 (wet bulb temperature). 定常状態の条件の下で大気を飽和させるため、一定の大気のサンプルに一定の圧力で純水を蒸発させる必要がある温度。 湿球温度は湿球温度計で 読み取る。 書き込み (write). ストレージ・デバイスまたはデータ・メディアに、永続的または一時的にデータを記録すること。 ラ イ ト ・ プ ロ テ ク ト (write protected). テープ・カートリッジに適用される、一部の論理または物理機構によってデバイスがそのカートリッジのテープに書き込まれないようにするときに存在する状 態。 ラ イ ト ・ プ ロ テ ク ト ・ ス イ ッ チ (write-protect switch).
目次ページへ戻る 概要: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM 概要 SCSI バス・インターフェース 機構 テープ・バックアップ・ソフトウェア フロント・パネル 背面パネル 概要 Dell PowerVault 110T LTO-3 テープ・ドライブは、高性能の大容量データ・ストレージ・デバイスで、自動バックアップの実行、オープン・システム・アプリケーションの復元、および、ファイルの検索 およびアーカイブを目的として設計されています。このドライブは、システムに統合する (内部モデル) ことも、別個にパッケージされたデスクトップ装置 (外部モデル) として提供することもできます。 Dell PowerVault 110T LTO-3 テープ・ドライブ (Generation 3 と呼ばれる) は、LTO 製品シリーズの第 3 世代テープ・ドライブです。 Dell PowerVault 110 LTO-3 テープ・ドライブは、最大容量 400 GB (2:1 の圧縮率を想定した場合は 800 GB) のフォーマット済みカートリッジ容量、お
l l l l l 省電力のためのスリープ・モード Generation 2 カートリッジとの読み取りおよび書き込みの後方互換性 Generation 1 カートリッジとの読み取りの後方互換性 正式な Ultrium LTO ロゴが付いたすべてのカートリッジとの互換性 正式な Ultrium LTO ロゴが付いた他の LTO テープ・ドライブとのテープの交換 * 最大の圧縮率を想定。実際に実現できる容量と転送速度はデータ・セットによって異なり、これは実際の圧縮率に影響します。 テープ・バックアップ・ソフトウェア DELL PowerVault 110T LTO-3 テープ・ドライブをサポートするバックアップ・ソフトウェアが必要です。一般的な規則として、ネイティブ・バックアップ・アプリケーション (NTBackup および tar な ど) は、テープ・ドライブの最高の性能を発揮するのに必要なデータ・ストリーム速度を提供しません。より良いメモリー管理が可能で、さらに TapeAlert などの他の便利な機能を提供するバックアッ プ・アプリケーションを使用することをお勧めします。サポートされる最新のソフトウ
背 面パネル 図 4. 内部テ ー プ ・ ド ラ イ ブ の背 面パ ネ ル 1. 2. 3. SCSI コネクター SCSI ID コネクター 電源コネクター 図 5. 外 部テ ー プ ・ ド ラ イ ブ の背 面パ ネ ル 1. 2. 3.
目次ページへ戻る テープ・ドライブのセットアップ: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM 事前に取り付け済みの内蔵ドライブ 内蔵ドライブの取り付け 外付けドライブの取り付け デバイス・ドライバーのロード ドライブ操作の検証 事 前に取り付け済み の内 蔵ドライブ Dell は、システムの一部として出荷される内蔵テープ・ドライブの取り付けおよびセットアップを行っています。テープのバックアップ・ソフトウェアは通常、Dell によってインストールされています。ただ し、ソフトウェアが最近更新された場合には、そのソフトウェアをインストールしなければならないことがあります。その場合、インストール手順はソフトウェアと共に提供されます。 サポートされる最新のソフトウェア・バージョンについては、 http://www.support.dell.
1. 2. システムの電源を切ります。 電気コンセントとシステムの両方から電源コードを外します。 ス テ ッ プ 3 — SCSI ID をセットする テープ・ドライブは、デフォルトの SCSI ID 6 で出荷されますが、0 から 15 の間の未使用 ID を割り当てることができます。 SCSI ID 7 は SCSI コントローラー用に予約されているため、使用しな いでください。また、SCSI ID 0 はブート・ディスクに割り当てられている場合が多いため、使用しないでください。 Narrow SCSI バスにドライブを取り付けると、性能が落ちるため、お勧めしません。 注意: 静電気によって電子コンポーネントに損傷を与える恐れがあります。可能であれば、帯電防止リスト・バンドを常に付けてください。リスト・バンドを付けられない場合は、電磁気の帯電 を逃がすために、コンピューターの塗装されていない金属部分 (バック・プレートなど) に触れてから、テープ・ドライブをバッグから取り出してください。 SCSI ID をセットするには、次のようにします。 1. 2. 3.
1. M-3 取り付けねじ穴 ケーブルを設置するためにドライブを動かす必要があるかもしれませんので、この時点ではドライブをねじで固定しないでください。 ス テ ッ プ 7 — 電 源ケーブルおよび SCSI ケーブルを接続す る 図 5 の番号 1 に示すように、システムの内部電源機構にあるスペアの電源ケーブルを電源コネクターに接続します。 図 5 の番号 2 に示すように、システムの SCSI リボン・ケーブルのスペアの SCSI ケーブルを SCSI コネクターに接続します。 注: ドライブが SCSI チェーン上の最後のデバイスである場合は、終端する必要があります。 図 5. 電 源ケ ー ブ ル お よ び SCSI ケ ー ブ ル を接続す る 1. 2.
ドライブの取り付け — 前 提条件 これらのテープ・ドライブは、low voltage differential (LVD) SCSI バス上で、160 MB/秒のバースト転送速度で作動するように設計されている Ultra160 SCSI デバイスです。このドライブの性 能を発揮させるためには、シングル・エンド SCSI バスでは使用しないでください。同じバス上で、他のシングル・エンド・デバイスとしては使用しないでください。それによって、LVD ホスト・アダプターがシ ングル・エンド・モードに切り替えられ、効率が落ちるためです。テープ・ドライブには、専用ホスト・バス・アダプターを使用することをお勧めします。 システムには、SCSI ホスト・アダプターまたはマザーボード上の SCSI コントローラー (SCSI-2 または SCSI-3 準拠) を適切に取り付け、テープ・ドライブをサポートするドライバー・ソフトウェアによ って構成する必要があります。組み込み SCSI チャネルの仕様については、システムの資料を調べてください。 RAID コントローラー・チャネルには接続しないでください。これはディスク・ドライブ
テープ・ドライブが SCSI バス上の唯一のデバイスである場合には、SCSI ケーブルの一方の端をシステムに接続します。 SCSI ケーブルのもう一方の端は、テープ・ドライブの背面パネルにあるどち らかの SCSI コネクター (図 7 の番号 3 を参照) に接続し、ねじで締めて固定します。このケーブルは、テープ・ドライブがバス上の唯一のデバイスであるときには、最長 25 m まで可能です。この構 成を図 8 に示します。 図 8. 1 台の SCSI デ バ イ ス を接続す る 1. 2. 3. 4. 5. 6. テープ・ドライブ SCSI コネクター ターミネーター SCSI バス・ケーブル SCSI ホスト・アダプター・カード システム テープ・ドライブが SCSI バス上の複数のデバイスの 1 つである場合は、SCSI ケーブルをそのバス上の次のデバイスに接続し、ターミネーターをバス上の最後のデバイスに移動してから、操作を再 開するホスト・コマンドを出します。この構成を図 9 に示します。このケーブルは最長 12 m まで可能です。 図 9.
Microsoft Windows 2003 このセクションでは、テープ・ドライブ用の Microsoft Windows 2003 デバイス・ドライバーのインストール、除去、および使用不可の方法について説明します。 イ ン ス ト ー ル手 順 1. 2. 3. ホスト・サーバーまたはワークステーションに管理者特権でログオンしていることを確認します。 Dell PowerVault 110T LTO-3 ドライブ・サポート CD を、ホスト・サーバーまたはワークステーションの CD ドライブに挿入します。 Windows デスクトップの「マ イ コ ン ピ ュ ー タ」アイコンを右クリックし、「管 理」をクリックして「デ バ イ ス マ ネ ー ジ ャ」をクリックします。 テープ・ドライブは、「? そのほかのデバイス」という項目の下に、「IBM Ultrium-TD3 SCSI Sequential Device」として表示されるはずです。 4. 5.
目次ページへ戻る テープ・バックアップ・ソフトウェアの使用: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザー ズ・ガイド TM TM ご使用のテープ・バックアップ・アプリケーションで提供されるユーザーの操作ガイドを参照してください。サポートされる最新のソフトウェア・バージョンについては、 http://www.support.dell.
目次ページへ戻る 仕様: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM 一般 外付けドライブ 内蔵ドライブ 注意: これらの仕様は、通知の目的でのみ製造元から提供されたものあり、 Dell の保証を拡張するものではありません。 Dell の保証内容は、ご使用のシステムの資料に記載されていま す。 一般 製造元 Dell 社向け 型式番号 DELL PowerVault 110T LTO-3 Tape Drive: LTO 内蔵型、LTO 外付型 インターフェース・タイプ Ultra160 Low Voltage Differential (LVD) SCSI バス 外 付けドライブ 物理仕様 幅 24.9 cm (9.8 in) 長さ 29.0 cm (11.42 in) 高さ 12.5 cm (4.92 in) 重量 6.45 kg (14.2 lb) 電源要件 AC 電源電圧 100–240 VAC 電源周波数 50–60 Hz、自動範囲設定 電源電流 (100 VAC) 0.
内 蔵ドライブ 物理仕様 幅 (ベゼルなし) 146.0 mm (5.75 in) 幅 (ベゼルあり) 148.3 mm (5.84 in) 長さ (ベゼルなし) 205.5 mm (8.09 in) 長さ (ベゼルあり) 210.5 mm (8.29 in) 高さ (ベゼルなし) 82.5 mm (3.25 in) 高さ (ベゼルあり) 84.8 mm (3.34 in) 重量 (カートリッジなし) 3 kg (6 lb 10 oz) 電源機構 許容度 + 5 VDC および + 12 VDC (± 10%) 電流 (5 VDC) 最小 1.3 A / 最大 3.0 A 電流 (12 VDC) 最小 0.2 A / 最大 1.1 A ピーク電源電流* (5 VDC) 100 ms15.5 W の場合 3.3 A ピーク電源電流* (12 VDC) 2 ms49.2 W の場合 4.5 A *電源機構による瞬間電力 消費電力 アイドル・モード、カートリッジなし 10 W アイドル・モード、カートリッジあり 12 W 読み取り/書き込み、6.
目次ページへ戻る トラブルシューティング: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM ドライバーおよびファームウェアのアップグレードの入手 診断または保守機能の選択 一般ガイドライン エラーおよびメッセージの受け取り方 説明および修正処置 システムによって通知される問題の解決 メディアに関連した問題の解決 テープ・ドライブの取り外し TapeAlert 手動でのテープ・カートリッジの取り外し ドライバーおよびファームウェアのアップグレードの入 手 注 意: フ ァ ー ム ウ ェ ア を更 新するときには、 更 新が完 了す る ま で は テ ー プ ・ ド ラ イ ブ の電 源を切らないでください。 電 源を切る と、フ ァ ー ム ウ ェ ア が失われるおそれがあります。 定期的に Web の http://support.dell.
機 能コ ー ド 5 — 予 約済み (サ ー ビ ス機 能) 機 能コ ー ド 6 — 予 約済み (サ ー ビ ス機 能) 機 能コ ー ド 7 — 予 約済み (サ ー ビ ス機 能) 機 能コ ー ド 8 — 予 約済み (サ ー ビ ス機 能) 機 能コ ー ド 9 — エラー・コード・ログの表 示 テープ・ドライブは、最新の 10 個のエラー・コードを 1 回に 1 つずつ表示します (コードは順に並べられ、最新のものが最初に表示され、最も古いもの (10 番目のもの) が最後に表示されます)。 ドライブ・エラー・ログを表示するには、次のようにします。 1. 2. カートリッジがドライブに入っていないことを確認します。 2 秒以内の間隔で、排出ボタンを 3 回押します。ステータス・ライトがこはく色に点灯します。つまり、ドライブが保守モードになっていることを意味します。 3. 4. 5. 6.
¡ 診断プログラムを即時に停止し、実行中のテストを終了させるには、排出ボタンを 2 回押します。テープ・ドライブは "0" を表示し、カートリッジの巻き戻しとアンロードを行って、保守 モードを終了します。 機 能コ ー ド H — ヘッドのテスト テープ・ドライブは、ヘッド耐性測定テストおよび (テープの中央部分での) 書き込み/読み取りテストを行います。ドライブは、これらのテストを実行して、テープ・ドライブのヘッドおよびテープ・カート リッジの機構部分が正しく作動していることを確認します。テープ・ドライブのテストの実行には、約 10 分かかります。 1. 2. カートリッジがドライブに入っていないことを確認します。 2 秒以内の間隔で、排出ボタンを 3 回押します。ステータス・ライトがこはく色に点灯します。つまり、ドライブが保守モードになっていることを意味します。 3. 1 文字ディスプレイに 4.
テープ・ドライブの 1 文字ディスプレイ。さらにステータス・ライトがこはく 色で明滅している。 『説明および修正処置』を参照してください。ステータス・ライトのアクティビティーの意味を判別するには、『概要』のフロン ト・パネルのセクションを参照してください。 テープ・ドライブの 1 文字ディスプレイ。さらにステータス・ライトがこはく 色で点灯している。 『診断または保守機能の選択』を参照してください。ステータス・ライトのアクティビティーの意味を判別するには、『概要』 のフロント・パネルのセクションを参照してください。 SCSI ログ・センス・データ (TapeAlert フラグなど) または SCSI ドライ ブ・センス・データ 『TapeAlert フラグ』または『説明および修正処置』を参照してください。 テープ・ドライブのエラー・ログ 『説明および修正処置』を参照してください。 説明および修 正処置 表 4 に、テープ・ドライブに関連するエラーおよびメッセージの説明と、それらを受け取ったときの処置方法を示します。 注意: テープ・ドライブが永続エラーを検出し、 以外のエラー・コードを表示す
複数のテープ・カートリッジで問題が発生した場合、またはテープ・カートリッジのボリューム通し番号が分からない場合は、テープ・ドライブの診断を実行します (『診断または保守機能の選 択』の機能コード 1 を参照)。 l l 診断が失敗した場合は、Dell のテクニカル・サポートに連絡してください。 診断が成功した場合は、ヘッドのテスト診断を実行する (『診断または保守機能の選択』の機能コード H を参照)。 ¡ ヘッドのテスト診断が失敗した場合は、Dell のテクニカル・サポートに連絡してください。 ¡ ヘッドのテスト診断が成功した場合は、問題を起こしたカートリッジを取り替える。 テープ・カートリッジを取り外すか、ドライブを保守モードにすると、エラー・コードはクリアされます。 デ ー タ の読み取り に関す る問 題: ドライブでテープからデータを読み取っているときに問題が起こり、そのテープ・カートリッジのボリューム通し番号が分かっている場合は、次のいずれかの手順を実行してください。 l l 使用可能な別のテープ・ドライブがある場合は、カートリッジを別のドライブに挿入して、操作を再試行する。 ¡ その操作
¡ エラーが起こらない場合は、1 回に 1 つのテープ・ドライブをバスに接続して、問題のあるドライブを識別できるまで各テープ・ドライブごとにステップ 3 を繰り返します。 注: SCSI ターミネーターは常に、SCSI バス上の最後のテープ・ドライブ上に置いてください。 4. 問題が 1 つのテープ・ドライブでのみ起こるのか、複数のテープ・ドライブで起こるのかを判別します。 ¡ 問題が 1 つのテープ・ドライブでのみ起こる場合は、次のことを行います。 n SCSI ターミネーターを交換して、失敗した操作を再試行します。 n SCSI ケーブルを交換し、変換コネクターがあればそれも交換して、失敗した操作を再試行します。 n これらの処置によって問題が訂正されない場合は、Dell のテクニカル・サポートに連絡してください。 ¡ 問題が複数のテープ・ドライブで起こる場合は、エラーのある最初のテープ・ドライブを見つけて、そのテープ・ドライブと変換コネクター (取り付けられている場合) を接続する SCSI ケ ーブルを交換します。 SCSI バ ス上の単一ドライブでの非 再 現 性エラーの修 正 1. 2.
TapeAlert TapeAlert は、テープ・ドライブに関してこれまでに起こった状態や問題について定義したテクノロジーと規格であり、米国規格協会 (ANSI) が特許権を持っています。このテクノロジーを使用すると、 システムは SCSI インターフェースを介してテープ・ドライブから TapeAlert フラグを読み取ることができます。システムは、ログ・センス・ページ 0x2E からフラグを読み取ります。 TapeAlert フラグ 表 5 に、Dell PowerVault 110T LTO-3 テープ・ドライブでサポートされる TapeAlert フラグをリストします。 表 5.
ドライブからカートリッジをアンロードする必要 がある障害が起こると、セットされます。 テープ・カートリッジをアンロードして、再ロードしてください。 33 21h Eject media (メディアの排出) 34 22h FMR (フィールド・マイクロコード交換) イメー Download fail (ダウンロード障害) ジが、SCSI インターフェース経由でテープ・ ドライブに正常にダウンロードできないとき に、セットされます。 36 24h Drive temperature (ドライブの 温度) ドライブの温度センサーによって、ドライブの 温度が、システムの推奨温度を超えているこ とが示されると、セットされます (『仕様』を参 照)。 『説明および修正処置』のエラー・コード 1 を参照してください。 37 25h Drive voltage (ドライブの電圧) 外部から供給される電圧が指定の電圧の許 容範囲外に近づいているか電圧の限界を超 えていることがドライブによって検出されると、 セットされます (『仕様』を参照)。 『説明および修正処置』のエラー・コード 2 を参照
目次ページへ戻る テープ・ドライブの使用: Dell PowerVault 110T LTO-3 テープ・ドライブ ユーザーズ・ガイド TM TM ドライブの操作 カートリッジのロード、アンロード、およびライト・プロテクト テープ・カートリッジの手入れ テープ機構のクリーニング ドライブの操 作 フロント・パネルにある電源オン/オフ・ボタンを押して外付けドライブの電源をオンにします (図 1 の番号 1 を参照)。テープ・ドライブは電源オン自己診断テスト (POST) を実行します。ハードウェアの 自己診断テスト終了時に、ステータス・ライトが緑色で点灯します。 図 1.
1. 2. 3. 4. 5. 6. LTO カートリッジ・メモリー ラベル域 ライト・プロテクト・スイッチ 挿入ガイド カートリッジ・ドア リーダー・ピン テープ・カートリッジのロード 1. 2. 3. 4. テープ・ドライブの電源がオンになっていることを確認します (ステータス・ライトが緑色で点灯)。 ライト・プロテクト・スイッチ (図 4 の番号 3 を参照) が正しくセットされていることを確認します (『カートリッジのライト・プロテクト・スイッチのセット」を参照)。 ライト・プロテクト・スイッチがユーザーの方に向くように、カートリッジを持ちます。 テープ・ロード格納機構にカートリッジをスライドさせて入れます (図 4 を参照)。 ¡ カートリッジがすでに排出位置にあるときに、そのカートリッジを再挿入したい場合は、カートリッジを取り外してから再び挿入します。 ¡ カートリッジがすでにロードされているときに、電源をサイクルする (電源をいったんオフにしてからオンにする) と、テープは再ロードされます。 図 4. ロ ー ド テープ・カートリッジのアンロード 1. 2. 3.
スイッチをセットするには、スイッチを左右にスライドさせて希望する位置にします。カートリッジをドライブに挿入してから赤いタブをスライドしても、カートリッジを取り出して再度挿入するまで変更は有効 になりません。 テープ・カートリッジの手 入れ 注意: 損傷のあるテープ・カートリッジを、テープ・ドライブに挿入しないでください。損傷したカートリッジを使用すると、ドライブの信頼性を損なうおそれがあり、ドライブとカートリッジの保証 が無効になることがあります。テープ・カートリッジを挿入する前に、カートリッジ・ケース、カートリッジ・ドア、およびライト・プロテクト・スイッチを調べて、破損個所がないか検査してください。 誤った取り扱いや不適切な環境によって、LTO Ultrium テープ・カートリッジやその磁気テープが損傷を受けるおそれがあります。テープ・カートリッジへの損傷を防ぐため、またテープ・ドライブの高い 信頼性を保つために、以下のガイドラインに従ってください。 保 守トレーニングの実施 l l l l l 人が集まる場所に、メディアの適切な取り扱いを記述した手順を掲示してください。 テープを取り扱う方が、取り
l l l カートリッジの外側に出ているテープには触れないこと。テープに触れると、テープの表面やエッジの部分に損傷を与えるおそれがあります。これは、読み取りや書き込みの信頼性を損なうことに つながります。カートリッジの外側に出ているテープを引っ張ると、テープとカートリッジのブレーキ機構に損傷を与えるおそれがあります。 6 個を超えるカートリッジを積み重ねないこと。 再利用する予定のカートリッジは消磁しないこと。消磁するとテープが使用できなくなります。 テープ機 構のクリーニング Dell PowerVault 110T LTO-3 ドライブは、クリーニングが少なくて済むように開発されています。テープ・ドライブは、ドライブのクリーニングが必要なときに 1 文字ディスプレイに C を表示し、ステ ータス・ライトをこはく色で明滅させます。 C が表示されたら、クリーニング・カートリッジだけをテープ・ドライブに挿入します。 注意: 「Universal」(ユニバーサル) というラベルが付いた LTO クリーニング・カートリッジだけを使用してください。一部の Generation 1 クリーニング・カートリッジに