Owner manual

ManualsBrandsDell ManualsComputer HardwarePowerVault 770N (Deskside NAS Appliance)

Table Of Contents

Notes, Notices, and Cautions
- /K CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Safety Instructions
- /j\ Precautions for Rack-Mountable Products
Installation Instructions
- /K CAUTION: Do not install rack kit components designed for another system. Use only the rack kit for your Dell system. Using the rack kit for another system may result in damage to the system and personal injury.
- Installation Tasks
- Recommended Tools and Supplies
- RapidRails Rack Kit Contents
- VersaRails Rack Kit Contents
Removing the Rack Doors
Marking the Rack
- Figure 1-3. One Rack Unit
□
□
□
□
□
- /t\ CAUTION: If you are installing more than one system, install the slide assemblies so that the first system is installed in the lowest available position in the rack.
- Installing the RapidRails Slide Assemblies
- Installing the VersaRails Slide Assemblies
- Installing the Tower-to-Rack Kit
- Installing the System in the Rack
- Installing the Cable-Management Arm
  - Installing the Cable Tray
    - /j\ CAUTION: The cable tray cannot support the weight of the system. Do not grasp the cable tray when lifting the system. Lift the system only by the chassis edges.
  - Securing the Cable-Management Arm
- Routing Cables
- Replacing the Rack Doors
- Remarques, mises en garde et avertissements
  - /î\ ATTENTION : Le message ATTENTION indique une situation potentiellement dangereuse qui, si elle n'est pas évitée, peut provoquer une blessure mineure ou modérée.
- Instructions de sécurité
  - /j\ Précautions à suivre concernant les produits destinés à être montés dans des racks
- Instructions d’installation
- Retrait des portes du rack
- Marquage du rack
  - Figure 2-3. Unité à un rack
□
□
□
□
□
- /t\ ATTENTION : si vous installez plus d'un système, installez les rails coulissants de façon à ce que le premier système soit placé le plus bas possible dans le rack.
- Installation des rails coulissants RapidRails
- Installation des rails coulissants VersaRails
- Installation du kit de conversion de tour en rack
- Installation du système dans le rack
- Installation du bras de maintien des câbles
  - Installation du chemin de câbles
    - ATTENTION : Le chemin de câbles ne peut pas supporter le poids du système. Ne touchez pas le chemin de câble lorsque vous soulevez le système. Soulevez le système uniquement par les bords du châssis.
  - Installation du bras de maintien des câbles
- Routage des câbles
- Remise en place des portes du rack
- Hinweis, Bitte Beachten und Vorsicht
  - /K VORSICHT: VORSICHT weist darauf hin, dass Gefahr für einen Sachschaden, Personenschaden oder Lebensgefahr besteht.
- Sicherheitshinweise
  - /j\ Vorsichtsmaßnahmen für Rack-montierbare Produkte
- Installationsanleitung
- Entfernen der Rack-Türen
- Markieren des Racks
  - Abbildung 3-3. Eine Rack-Einheit
□
□
□
□
□
- /t\ VORSICHT: Wenn Sie mehr als ein System installieren, installieren Sie die
- Gleitschienen so, dass das erste System in der untersten möglichen Position im Rack installiert ist.
- Befestigen der RapidRails-Gleitschienen
- Befestigen der VersaRails-Gleitschienen
- Installieren des Tower-nach-Rack-Kits
  - Entfernen von Blende, Füßen Abdeckung, Seitenteil und Frontplatte
  - Installieren der Rack-Frontplatte und -Blende
- Installieren des Systems im Rack
  - VORSICHT: Das System ist sehr groß und schwer, also versuchen Sie niemals, es ohne fremde Hilfe in den Gleitschienen zu installieren.
- Einbau des Kabelarms
  - Installation der Kabelführung
  - Befestigen des Kabelarms
- Verlegen der Kabel
- Einsetzen der Rack-Türen
  - o
  - Ft, 0 ч;,
  - m A '
  - с
  - ^ ^ э
  - afe Ч м
    - 9+
  - 1
  - w
  - >S
  - 3
  - á®
  - п>
  - Л
    - VersaRails +
      - 4 4-3. 1U
  - Ml Э
  - VI Ml V
  - M V
  - EE
  - 3 Ml Ш ЗАЗ
  - 3 V
  - 1 А
  - 4 V
  - V
  - м Q V Ч А ч
  - 5Ш А 3
- vil
- VersaRails
- h
- Notas, avisos y precauciones
  - /K PRECAUCIÓN: un mensaje de PRECAUCIÓN indica la posibilidad de que el equipo resulte averiado, de sufrir lesiones personales o incluso la muerte.
- Instrucciones de seguridad
  - /j\ Precauciones para los productos montados en rack
- Instrucciones de instalación
- Desmontaje de las puertas del rack
- Marcado del rack
  - Figura 5-3. Una unidad de rack
□
□
□
□
□
- /t\ PRECAUCIÓN: si va a montar más de un sistema, monte los conjuntos
- deslizantes de modo que el primer sistema se monte en la posición más baja disponible en el rack.
- Montaje de los conjuntos deslizantes RapidRails
  - Figura 5-5. Montaje de los conjuntos deslizantes RapidRails
- Montaje de los conjuntos deslizantes VersaRails
  - Figura 5-6. Montaje de los conjuntos de guía VersaRails
- Montaje del kit de torre a rack
- Montaje del sistema en el rack
- Montaje de la extensión para tendido de cables
  - Montaje de la bandeja para cables
    - PRECAUCIÓN: la bandeja para cables soporta el peso del sistema. No agarre la bandeja para cables al levantar el sistema. Levante el sistema solo por los bordes del chasis.
  - Fijación de la extensión para tendido de cables
    - Figura 5-14. Montaje de la extensión para tendido de cables
- Tendido de cables
- Colocación de las puertas del rack

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the

rack.

• Use caution when pressing the component rail release latches and sliding a component

into or out of a rack* the slide rails can pinch your fingers.

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

• Do not overload the power supply branch circuit that provides power to the rack.

The total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any system/component when servicing other

systems/components in a rack.

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or

more systems in an open-frame relay rack or in a rack cabinet. The Dell™ RapidRails™ rack

kit can be installed in all the manufacturer’s rack cabinets without tools, and the

VersaRails™ rack kit can be installed in most industry-standard rack cabinets. The

procedures for installing both RapidRails and VersaRails rack kits are similar. One rack kit is

required for each system installed in the rack.

/K CAUTION: Do not install rack kit components designed for another system. Use

only the rack kit for your Dell system. Using the rack kit for another system may

result in damage to the system and personal injury.

^ NOTE: If your Dell system Is a tower version, you must Install a tower-to-rack kit. Instructions

for Installing this kit are Included In this document.

The RapidRails rack kit can be installed in any Dell rack cabinet and in most industry-

standard rack cabinets.

O NOTICE: The VersaRails rack kit is intended to be installed by trained service

technicians In a rack that meets the specifications of American National Standards

Institute (ANSD/Electronic Industries Association (EIA) standard ANSI/EIA-310-

D-92, International Electrotechnical Commission (IEC) 297, and Deutsche Industrie

Norm (DIN) 41494. One rack kit is required for each system that is installed in a

rack.

1-2 I Rack Installation Guide