Dell™ PowerVault™ DL2000 Manuel du propriétaire w w w. d e l l . c o m | s u p p o r t . d e l l .
Remarques, avis et précautions REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : un AVIS vous avertit d'un risque d’endommagement du matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION : une PRÉCAUTION vous avertit d'un risque d'endommagement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document sont sujettes à modification sans préavis.
Table des matières 1 À propos du système . Autres informations utiles . . . . . . . . . . . . . . . 11 . . . . . . . . . . . . . . . 11 Fonctions du système accessibles au démarrage . . . 12 Voyants et fonctions du panneau avant . . . . . . . . . 13 Codes des voyants de disques durs . . . . . . . . 15 Voyants et fonctions du panneau arrière . . . . . . . . 17 Connexion de périphériques externes . . . . . . . 18 Codes du voyant d'alimentation . . . . . . . . . . . .
2 Utilisation du programme de configuration du système . . . . . . . . . . . . Accès au programme de configuration du système Réponse aux messages d'erreur . . . 49 . . . . . . . . . 50 Utilisation du programme de configuration du système . . . . . . . . . . . . . . . . . . . . . 50 . . . . . . . . . . 50 . . . . . . . . . . . . . . . . . . . 50 Options de configuration du système Écran principal Écran Memory Information (Informations sur la mémoire) . . . . . . . . . . . . . . . . . . . .
3 Installation des composants du système . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Outils recommandés . . . . . . . . . . . . . . . . . . 69 Intérieur du système . . . . . . . . . . . . . . . . . . . 70 . . . . . . . . . . . . . . . . . . . . . . . 71 Cadre avant Retrait du cadre avant . . . . . . . . . . . . . . . 71 Réinstallation du cadre avant . . . . . . . . . . . 72 Ouverture et fermeture du système . . . . . . . . . . . 72 Ouverture du système . . . . . . . . . . .
Ventilateurs du système . . . . . . . . . . . . . . . . . . . . . . . . . 84 . . . . . . . . . . . 86 . . . . . . . . . . . . . . 86 Retrait d'un ventilateur du système Réinstallation d'un ventilateur Carénage de refroidissement Retrait du carénage de refroidissement . . . . . . 87 . . . . . . . . . . . . . . . . . 88 Retrait du support de ventilateur . . . . . . . . . . Carte contrôleur fille SAS 89 . . . . . . . . . . . . . . . . 90 Installation d'une carte contrôleur fille SAS . . . .
Mémoire système . . . . . . . . . . . . . . . . . . . . Consignes générales pour l'installation des modules de mémoire . . . . . . . . . . . . . 103 . . . 103 Configurations de mémoire non optimales . . . . 104 Prise en charge d'une mémoire de réserve . . . . 104 Prise en charge de la mise en miroir de la mémoire . . . . . . . . . . . . . . . . . . . . . . 105 . . . . . . . . 105 . . . . . . . . . .
Assemblage du panneau de commande (procédure réservée à la maintenance) . . . . . . . . . . . . . Retrait de l'assemblage du panneau de commande . . . . . . . . . . . . . . . . . 125 . . . . . . 125 Installation de l'assemblage du panneau de commande . . . . . . . . . . . . . . . . . . . . . 126 . . . . . . . 127 . . . . . . . . . . . . . 127 Carte système (maintenance uniquement) Retrait de la carte système Installation de la carte système 4 Dépannage du système . . . . . . . . . . . . . .
Dépannage des problèmes de refroidissement du système . . . . . . . . . . . . . . . . . . . . . . Dépannage d'un ventilateur . . . 143 . . . . . . . . . . . . 143 Dépannage de la mémoire système . Dépannage d'un lecteur optique . . . . . . . . . . 145 . . . . . . . . . . . . 147 Dépannage d'un lecteur de bande SCSI externe Dépannage d'un disque dur . . . . 148 . . . . . . . . . . . . . . . 149 . . . . . . 151 . . . . . . . . . . 152 . . . . . . . . . . .
6 Cavaliers et connecteurs Cavaliers de la carte système . . . . . . . . . . . . . . . . . . . . . . . . . Connecteurs de la carte système . . . . . . . . . . . . Connecteurs de la carte de fond de panier SAS Connecteurs de la carte latérale Contacter Dell 165 168 . . . . . . . . . . . . 169 Désactivation d'un mot de passe oublié Obtention d'aide 163 . . . . Composants et bus PCI de carte de montage pour carte d'extension . . . . . . . . . . . . . . . . . 7 163 . . . 169 . . . . . . . .
À propos du système Cette section décrit les principales caractéristiques du système et couvre notamment le matériel, le micrologiciel et l'interface logicielle. Les connecteurs situés sur les panneaux avant et arrière du système permettent au système de bénéficier d'une connectivité optimale et de nombreuses possibilités d'extension. Le micrologiciel, les applications et le système d'exploitation gèrent le système ainsi que l'état des composants. Ils vous alertent lorsqu'un incident survient.
• La documentation du système d'exploitation indique comment installer (au besoin), configurer et utiliser le système d'exploitation. • La documentation fournie avec les composants achetés séparément indique comment installer et configurer ces options. • Des mises à jour sont parfois fournies avec le système. Elles décrivent les modifications apportées au système, aux logiciels ou à la documentation. REMARQUE : vérifiez toujours si des mises à jour sont disponibles sur le site support.dell.
Tableau 1-1. Touches d'accès aux fonctions du système (suite) Touche(s) Description Ouvre l'utilitaire de configuration RAID, qui permet de configurer une carte RAID en option. Pour plus d'informations, reportez-vous à la documentation de la carte RAID. Cette option s'affiche uniquement si le support PXE est activé dans le programme de configuration du système (reportez-vous à la section « Écran Integrated Devices (Périphériques intégrés) », à la page 55).
Tableau 1-2. Voyants, boutons et connecteurs du panneau avant Élément Voyant, bouton ou connecteur 1 Voyant et bouton d'alimentation Icône Description Le voyant d'alimentation s'allume lorsque le système est sous tension. Le bouton d'alimentation contrôle la sortie du bloc d'alimentation en CC qui alimente le système.
Tableau 1-2. Voyants, boutons et connecteurs du panneau avant (suite) Élément Voyant, bouton ou connecteur 4 Icône Écran LCD Description Affiche l'ID du système, des informations d'état et des messages d'erreur. L'écran LCD s'allume lorsque le système fonctionne normalement. Les logiciels de gestion de systèmes, tout comme les boutons d'identification situés à l'avant et à l'arrière du système, peuvent faire clignoter l'écran LCD en bleu pour identifier un système spécifique.
Figure 1-2. Voyants de disque dur 1 2 1 voyant d'état du lecteur (vert et orange) 2 voyant d'activité du lecteur (vert) Le Tableau 1-3 répertorie les codes des voyants des disques durs RAID. Les codes varient en fonction des événements affectant les lecteurs du système. Par exemple, si un disque dur tombe en panne, la séquence « Échec du disque » apparaît.
Tableau 1-3.
1 carte de montage PCI centrale (logement 1) 2 carte de montage PCI de gauche (logement 2) 3 carte de montage PCI de gauche (logement 2) 4 modules d'alimentation (2) 5 bouton d'identification du système 6 voyant d'état du système 7 connecteur du voyant d'état du système 8 connecteur NIC2 9 connecteur NIC1 10 connecteurs USB (2) 11 connecteur vidéo 12 connecteur série 13 Dell remote access controller (en option) Connexion de périphériques externes Appliquez les consignes suivantes l
Codes du voyant d'alimentation Le bouton d'alimentation du panneau avant contrôle la mise sous tension des blocs d'alimentation du système. Le voyant d'alimentation s'allume en vert quand le système est sous tension. Les voyants des blocs d'alimentation redondants indiquent si le système est alimenté et permettent de détecter une éventuelle panne d'alimentation (reportez-vous à la Figure 1-4). Le Tableau 1-4 répertorie les codes des voyants des blocs d'alimentation. Tableau 1-4.
Codes des voyants de carte NIC Chaque NIC du panneau arrière est associé à un voyant qui fournit des informations sur l'activité du réseau et l'état du lien. Reportez-vous à la Figure 1-5. Le Tableau 1-5 répertorie les codes des voyants d'activité réseau. Figure 1-5. Voyants d'activité réseau 2 1 1 Tableau 1-5. voyant de lien 2 voyant d'activité Codes des voyants de carte NIC Voyant Code du voyant Les voyants de lien et d'activité sont éteints. La carte NIC n'est pas connectée au réseau.
PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. REMARQUE : si le démarrage du système échoue, appuyez sur le bouton d'ID du système pendant au moins cinq secondes, jusqu'à ce qu'un code d'erreur s'affiche sur l'écran LCD. Notez ce code, puis reportez-vous à la section « Obtention d'aide », à la page 173. Tableau 1-6.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E12nn xx PwrGd Panne du régulateur de tension indiqué. Reportez-vous à la section « Obtention d'aide », à la page 173. E1210 CMOS Batt La pile CMOS est manquante ou la tension est en dehors des limites autorisées. Reportez-vous à la section « Dépannage de la batterie du système », à la page 141. E1229 CPU # VCORE Panne du régulateur de tension VCORE du processeur n.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E1414 CPU # Thermtrip La température du microprocesseur spécifié est en dehors des limites autorisées et celui-ci s'est arrêté. Reportez-vous à la section « Dépannage des problèmes de refroidissement du système », à la page 143. Si le problème persiste, assurez-vous que les dissipateurs de chaleur du microprocesseur sont correctement installés.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes E141C CPU Mismatch La configuration des Vérifiez que les processeurs n'est pas prise processeurs sont de même en charge par Dell. type et conformes aux spécifications décrites dans le Guide de mise en route du système. E141F CPU Protocol Le BIOS du système a renvoyé une erreur de protocole liée au processeur. Reportez-vous à la section « Obtention d'aide », à la page 173.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E161C PS # Input Lost La source d'alimentation du bloc d'alimentation indiqué est indisponible ou en dehors des limites autorisées. Vérifiez la source de CA du bloc d'alimentation indiqué. Si le problème persiste, reportez-vous à la section « Dépannage des blocs d'alimentation », à la page 142.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte E1711 PCI PERR B## D## F## Causes Le BIOS du système a renvoyé une erreur de parité PCI liée à un PCI PERR Slot composant résidant dans # l'espace de configuration PCI du bus ##, périphérique ##, fonction ##. Le BIOS du système a renvoyé une erreur de parité PCI liée à un composant installé dans le logement PCI indiqué.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes E1714 Unknown Err Le BIOS du système a Reportez-vous à la section détecté une erreur système « Obtention d'aide », à la non identifiée. page 173. E171F PCIE Fatal Err B## D## F## Le BIOS du système a renvoyé une erreur fatale PCIe liée à un composant résidant dans l'espace de configuration PCI du bus nn, périphérique nn, fonction n. Retirez et réinstallez les cartes d'extension PCI.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E1913 CPU & Firmware Mismatch Le micrologiciel du contrôleur BMC ne prend pas en charge le processeur. Installez la version la plus récente du micrologiciel pour le contrôleur BMC. Reportez-vous au document BMC User's Guide (Contrôleur BMC Guide d'utilisation) pour plus d'informations sur la configuration et l'utilisation de ce contrôleur.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E2010 No Memory Aucune mémoire n'est installée dans le système. Installez de la mémoire. Reportez-vous à la section « Installation de modules de mémoire », à la page 105. E2011 Mem Config Err Mémoire détectée mais non configurable. Erreur détectée lors de la configuration de la mémoire. Reportez-vous à la section « Dépannage de la mémoire système », à la page 145.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E201A SIO Err Échec de la puce Super E/S. Reportez-vous à la section « Obtention d'aide », à la page 173. E201B Kybd Controller Échec du contrôleur de clavier. Reportez-vous à la section « Obtention d'aide », à la page 173. E201C SMI Init Échec d'initialisation SMI Reportez-vous à la section (System Management « Obtention d'aide », à la Interrupt). page 173.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives E2021 Memory Population Configuration de la mémoire incorrecte. L'ordre d'insertion des barrettes de mémoire est incorrect. Vérifiez si l'écran affiche des messages d'erreur spécifiques. Reportez-vous à la section « Dépannage de la mémoire système », à la page 145. E2022 POST Fail Échec général après le test Vérifiez si l'écran affiche vidéo. des messages d'erreur spécifiques.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte E2112 Mem Spare Crd Le BIOS du système a activé la mémoire de # DIMM ## réserve car il a détecté un nombre d'erreurs trop important. « ## &t ## » représente la paire de barrettes DIMM indiquée par le BIOS. Si le système n'est pas équipé d'une carte de mémoire, la chaîne « Crd # » n'apparaît pas dans le message. Reportez-vous à la section « Dépannage de la mémoire système », à la page 145.
Tableau 1-6. Messages d'état affichés sur l'écran LCD (suite) Code Texte Causes Mesures correctives I1911 >3 ERRs Chk Log Les messages à afficher dépassent la capacité de l'écran LCD. Vérifiez le journal d'événements du système pour plus de détails. L'écran LCD ne peut afficher que trois messages d'erreur à la suite. Le quatrième message indique que la capacité de l'écran est à son maximum. I1912 SEL Full Le journal d'événements Supprimez des du système est saturé et ne événements du journal.
• Clear the SEL (Effacer le journal d'événements du système) : cette tâche peut être effectuée à distance. Elle supprime l'historique des événements du système. • Power cycle (Mettre le système hors tension) : éteignez le système et débranchez-le de la prise secteur. Attendez environ 10 secondes, puis rebranchez le câble d'alimentation et redémarrez le système. Ces interventions permettent d'effacer les messages d'erreur. Les voyants d'état et l'écran LCD reviennent à l'état normal.
Tableau 1-7. Messages système Message Causes Mesures correctives Alert! Redundant memory disabled! Memory configuration does not support redundant memory. Les modules de mémoire installés ne sont pas du même type ni de la même taille ; un ou plusieurs modules de mémoire sont défectueux. Vérifiez que tous les modules de mémoire sont du même type et de la même taille et qu'ils sont correctement installés.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives DIMM pairs must be matched in size, speed, and technology. The following DIMM pair is mismatched: DIMM x and DIMM y. Modules DIMM incompatibles ; module(s) de mémoire défectueux ou mal installé(s). Vérifiez que toutes les paires de modules de mémoire sont de même type et de même taille et qu'elles sont correctement installées. Reportez-vous à la section « Mémoire système », à la page 103.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Dual-rank DIMM paired with Single-rank DIMM The following DIMM/rank has been disabled by BIOS: DIMM x Rank y Modules DIMM incompatibles ; module(s) de mémoire défectueux. Le système a détecté qu'un module DIMM à double rangée de connexions a été installé avec un module à une seule rangée de connexions. La seconde rangée du premier module sera désactivée.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Diskette subsystem Lecteur de disquette ou de Remplacez la disquette ou la reset failed bande défectueux ou mal bande. Si le problème installé. persiste, reportez-vous à la section « Dépannage d'un lecteur optique », à la page 147. Drive not ready Disquette manquante ou Remplacez la disquette. Si le mal insérée dans le lecteur. problème persiste, reportezvous à la section « Dépannage d'un lecteur optique », à la page 147.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives FBD training error: The following branch has been disabled: Branch x. Le circuit indiqué (paire de canaux) contient des barrettes DIMM qui ne sont pas compatibles entre elles. Vérifiez que vous utilisez uniquement des barrettes de mémoire certifiées par Dell. Nous vous recommandons d'acheter les kits d'extension de mémoire directement sur le site www.dell.com ou de contacter votre représentant commercial Dell à cet effet.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Memory address line failure at address, read value expecting value Barrettes de mémoire défectueuses ou mal installées. Reportez-vous à la section « Dépannage de la mémoire système », à la page 145.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives No boot device available Sous-système du lecteur optique, de disquette ou de disque dur défectueux ou manquant ; disque dur défectueux ou manquant ou aucune disquette de démarrage dans l'unité A. Utilisez une disquette, un CD ou un disque dur amorçable.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Not a boot diskette La disquette ne contient aucun système d'exploitation. Utilisez une disquette amorçable. PCIe Degraded Link Carte PCIe défectueuse ou mal installée dans le Width Error: support spécifié. Embedded Bus#nn/Dev#nn/Funcn Expected Link Width is n Actual Link Width is n Réemboîtez la carte PCIe dans le logement indiqué. Reportez-vous à la section « Cartes d'extension », à la page 93.
Tableau 1-7. Messages système (suite) Message Causes Plug & Play Configuration Error Erreur d'initialisation d'un Installez la fiche du cavalier périphérique PCI ; carte NVRAM_CLR et mère défectueuse. redémarrez le système. Reportez-vous à la Figure 6-1 pour identifier son emplacement. Si le problème persiste, reportezvous à la section « Dépannage des cartes d'extension », à la page 152.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Sector not found Lecteur de disquette ou disque dur défectueux. Reportez-vous à la section « Dépannage d'un lecteur optique », à la page 147, « Dépannage d'un périphérique USB », à la page 137 ou « Dépannage d'un disque dur », à la page 149pour vérifier si les lecteurs installés dans votre système sont adaptés. Shutdown failure Échec du test d'arrêt.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives The following Les modules DIMM DIMMs are not indiqués sont compatible: DIMM x incompatibles avec le and DIMM y système. Time-of-day not set - please run SETUP program Utilisez exclusivement des modules FB-DIMM1 avec ECC. Nous vous recommandons d'acheter les kits d'extension de mémoire directement sur le site www.dell.com ou de contacter votre représentant commercial Dell à cet effet.
Tableau 1-7. Messages système (suite) Message Causes Mesures correctives Warning: Embedded RAID firmware is not present. Le micrologiciel RAID intégré ne répond pas. Lisez la documentation du contrôleur RAID pour obtenir des informations sur l'installation et la mise à jour du micrologiciel RAID. Warning: Embedded RAID error. Le micrologiciel RAID Reportez-vous à la section intégré renvoie une erreur. « Dépannage d'une carte contrôleur fille SAS », à la page 151.
Messages d'avertissement Un message d'avertissement signale un problème possible et vous demande une réponse avant de laisser le système poursuivre son exécution. Par exemple, lorsque vous lancez le formatage d'une disquette, un message vous avertit que vous allez perdre toutes les données qu'elle contient. Les messages d'avertissement interrompent la tâche en cours et vous demandent de répondre en tapant y (pour oui) ou n (pour non).
À propos du système
Utilisation du programme de configuration du système Après avoir installé le système, lancez le programme de configuration pour vous familiariser avec la configuration et les paramètres facultatifs disponibles. Notez ces informations pour pouvoir vous y reporter ultérieurement.
Réponse aux messages d'erreur Vous pouvez accéder au programme de configuration du système en répondant à certains messages d'erreur. Si un message d'erreur s'affiche quand le système démarre, prenez-en note. Avant d'accéder au programme de configuration du système, reportez-vous à la section « Messages système », à la page 34 pour trouver une explication du message et des suggestions de correction.
Figure 2-1. Écran principal du programme de configuration du système Le Tableau 2-2 répertorie les options des champs qui apparaissent dans l'écran principal du programme de configuration du système et il décrit ces derniers. REMARQUE : les options disponibles du programme de configuration du système varient en fonction de la configuration du système. REMARQUE : les valeurs par défaut du programme de configuration du système sont répertoriées sous l'option correspondante, le cas échéant. Tableau 2-2.
Tableau 2-2. Options du programme de configuration du système (suite) Option Description Memory Information (Informations mémoire) Affiche des informations relatives à la mémoire système, vidéo et redondante, y compris la taille, le type et la vitesse. CPU Information Affiche des informations relatives aux microprocesseurs (vitesse, (Informations UC) taille de la mémoire cache, etc.).
Tableau 2-2. Options du programme de configuration du système (suite) Option Description PCI IRQ Affiche un écran permettant de modifier l'IRQ affectée à Assignment chaque périphérique intégré du bus PCI, ainsi qu'à toutes les (Affectation d'IRQ cartes d'extension nécessitant une IRQ.
Tableau 2-3. Écran Memory Information (Informations sur la mémoire) Option Description System Memory Size Affiche la quantité de mémoire système. System Memory Type Affiche le type de la mémoire système. System Memory Speed Affiche la vitesse de la mémoire système. Video Memory Affiche la quantité de mémoire vidéo. System Memory Testing Indique si la mémoire système doit être testée à chaque amorçage. Les options disponibles sont Enabled (Activé) et Disabled (Désactivé).
Tableau 2-4. Écran CPU Information (Informations sur le processeur) Option Description Bus Speed Affiche la vitesse de bus des processeurs. Logical Processor (Option par défaut : Enabled [Activé]) Indique si les processeurs prennent en charge la fonction HyperThreading. L'option Enabled (Activé) permet au système d'exploitation d'utiliser tous les processeurs logiques.
Tableau 2-5. Options de l'écran Integrated Devices (Périphériques intégrés) Option Description Integrated SAS Active ou désactive le contrôleur SAS intégré. Controller (Option par défaut : Enabled [Activé]) Embedded SATA Permet de paramétrer le contrôleur SATA intégré sur Off (Option par défaut : (Désactivé) ou sur ATA Mode (Mode ATA). Off [Désactivé]) IDE CD-ROM Controller (Option par défaut : Auto) Active le contrôleur IDE intégré.
Tableau 2-5. Options de l'écran Integrated Devices (Périphériques intégrés) (suite) Option Description Embedded Gb NIC2 Enabled with PXE (Activé avec PXE, option par défaut) Active ou désactive la carte NIC intégrée du système. Les options disponibles sont Enabled without PXE (Activé sans PXE), Enabled with PXE (Activé avec PXE) et Disabled (Désactivé). Le support PXE permet au système de démarrer à partir du réseau. Les modifications prennent effet après le redémarrage du système.
Écran Serial Communication (Communications série) Le Tableau 2-6 répertorie les options et les descriptions des champs qui apparaissent dans l'écran Serial Communication (Communications série). Tableau 2-6. Options de l'écran Serial Communication (Communications série) Option Description Serial Communication Les options disponibles sont On with Console Redirection (Option par défaut : (Activé avec redirection de console) via COM2 et Off Off [Désactivé]) (Désactivé).
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option Description Setup Password (Mot de passe de configuration) Restreint l'accès au programme de configuration du système, tout comme le mot de passe système protège l'accès à ce dernier. REMARQUE : reportez-vous à la section « Utilisation du mot de passe de configuration », à la page 66 pour plus d'instructions sur l'attribution, l'utilisation ou la modification d'un mot de passe de configuration existant.
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option Description TPM Security Définit les modalités de déclaration de la puce TPM (Trusted (Option par défaut : Platform Module) dans le système. Off [Désactivé]) Lorsque l'option Off (Désactivé) est sélectionnée, la présence de la puce TPM n'est pas signalée au système d'exploitation.
Tableau 2-7. Options de l'écran System Security (Sécurité du système) (suite) Option TPM Clear (Option par défaut : No) Description AVIS : l'effacement de la puce TPM entraîne la perte de toutes les clés de cryptage qu'elle contient. Cette opération empêche le démarrage du système d'exploitation. Si les clés de cryptage ne peuvent pas être restaurées, des données risquent d'être perdues. Vous devez donc impérativement créer une copie de sauvegarde des clés TPM avant d'activer cette option.
Tableau 2-7. Option Options de l'écran System Security (Sécurité du système) (suite) Description AC Power Recovery Détermine le comportement du système au retour de (Option par défaut : l'alimentation secteur. L'option Last (Dernier) indique que le Last [Dernier]) système doit revenir au même état qu'avant la coupure d'alimentation. Avec l'option On (Marche), le système démarre dès que l'alimentation en CA est rétablie.
Vous ne pouvez changer ou supprimer un mot de passe que si vous le connaissez (reportez-vous à la section « Suppression ou modification d'un mot de passe système existant », à la page 65). Si vous avez oublié votre mot de passe, vous ne pourrez pas faire fonctionner le système ni modifier sa configuration tant qu'un technicien de maintenance qualifié n'aura pas effacé les mots de passe en déplaçant le cavalier approprié sur la carte système.
3 Saisissez le nouveau mot de passe système. Le mot de passe peut contenir jusqu'à 32 caractères. Les caractères entrés ne sont pas affichés dans le champ ; ils sont remplacés (y compris les espaces) par des caractères génériques. Le mot de passe ne tient pas compte de la différence entre majuscules et minuscules. Cependant, certaines combinaisons de touches ne sont pas valides. Si vous entrez l'une de ces combinaisons, le système émet un signal sonore.
Pour désactiver la protection par mot de passe : 1 Démarrez le système ou redémarrez-le en appuyant sur . 2 Saisissez le mot de passe et appuyez sur . Si l'option Password Status (État du mot de passe) a la valeur Locked (Verrouillé) lorsque vous allumez ou redémarrez le système (en appuyant sur ), saisissez votre mot de passe et appuyez sur à l'invite.
5 Vérifiez que l'option System Password (Mot de passe système) est définie sur Not Enabled (Non activé). Si tel est le cas, le mot de passe système a été supprimé. Si l'option System Password (Mot de passe système) est définie sur Enabled (Activé), appuyez sur pour redémarrer le système, puis recommencez les étapes 2 à 5.
Fonctionnement du système avec un mot de passe de configuration activé Si le paramètre Setup Password (Mot de passe de configuration) a la valeur Enabled, (Activé) vous devez entrer ce mot de passe pour modifier la plupart des options de configuration du système. Une invite de saisie s'affiche lorsque vous accédez au programme de configuration du système.
Configuration du contrôleur BMC Le contrôleur BMC permet de configurer, contrôler et restaurer les systèmes à distance.
Installation des composants du système Cette section décrit l'installation des composants suivants : • Disques durs • Blocs d'alimentation • Ventilateurs du système • Carénage de refroidissement • Supports de ventilateur • Carte contrôleur fille SAS • Cartes d'extension • Boîtier de cartes d'extension • Carte DRAC • Lecteur optique • Mémoire système • Processeurs • Batterie du système • Cartes de montage pour cartes d'extension • Carte latérale • Carte de fond de panier SAS • Assemblage du panneau de comman
Intérieur du système PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. Dans la Figure 3-1, les panneaux sont ouverts pour montrer l'intérieur du système. Figure 3-1.
La carte système contient les circuits de contrôle du système et d'autres composants électroniques. Plusieurs options matérielles, telles que les microprocesseurs et la mémoire, sont directement installées sur la carte système. Le boîtier de cartes d'extension contenant la carte de montage de gauche peut recevoir deux cartes d'extension PCIe ou PCI-X pleine longueur. La carte de montage centrale peut accueillir une seule carte d'extension PCIe demi-longueur.
Figure 3-2. Retrait du cadre avant 2 1 1 verrou du cadre 2 écran LCD du panneau de commande Réinstallation du cadre avant Pour réinstaller le cadre avant, suivez les étapes précédentes dans l'ordre inverse. Ouverture et fermeture du système PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système.
1 À moins que vous n'installiez un composant enfichable à chaud tel qu'un ventilateur ou un bloc d'alimentation, vous devez arrêter le système et les périphériques connectés, puis le débrancher de la prise secteur et des périphériques. 2 Pour retirer le capot du système, tournez le verrou du loquet de dégagement dans le sens inverse des aiguilles d'une montre. Reportez-vous à la Figure 3-3. 3 Soulevez le loquet situé sur la partie supérieure du système. Reportez-vous à la Figure 3-3.
Figure 3-3. Retrait du capot 1 2 3 1 loquet 3 crochets d'alignement en J 2 verrou du loquet de dégagement Disques durs Cette sous-section décrit les procédures permettant d'installer et de configurer des disques durs SCSI dans les baies internes du système. Votre système compte jusqu'à quatre disques durs SATA 3,5 pouces. Tous les disques sont connectés à la carte système par l'intermédiaire d'une carte de fond de panier SAS.
Avant de commencer Les disques durs sont fournis dans des supports de lecteur spéciaux enfichables à chaud, qui s'encastrent dans les baies de disques durs. Selon la configuration que vous utilisez, vous avez reçu l'un des deux types de support de disque suivants : • Support d'unité SATA : utilisable uniquement avec un disque dur SATA. • Support d'unité SATAu : utilisable avec un disque dur SAS ou avec un disque dur SATA équipé d'une carte intermédiaire universelle.
Installation d'un cache de lecteur Le cache de lecteur est muni d'un détrompeur permettant de s'assurer qu'il sera correctement inséré dans la baie. Pour installer un cache de lecteur 3,5 pouces, insérez et faites pivoter le côté doté de repères dans la baie de lecteurs. Appuyez de manière égale sur l'autre côté du cache jusqu'à ce qu'il soit correctement emboîté. Retrait d'un disque dur enfichable à chaud 1 Retirez le cadre avant, s'il est installé.
1 Retirez le cadre avant, s'il est installé. Reportez-vous à la section « Retrait du cadre avant », à la page 71. 2 Si la baie est fermée par un cache, retirez-le. Reportez-vous à la section « Retrait d'un cache de lecteur », à la page 75. 3 Installez le disque dur enfichable à chaud. a Ouvrez la poignée du support de disque dur. Figure 3-4.
Réinstallation d'un support de disque dur Retrait d'un disque dur installé dans un support 1 Si vous retirez un disque dur SATA d'un support SATAu, retirez la carte intermédiaire : a Repérez le levier d'éjection. Lorsque le support de disque dur est vu depuis l'arrière, ce levier se trouve à l'extrémité gauche de la carte intermédiaire. b Écartez le levier du rail du support afin de libérer le côté gauche de la carte. c Faites pivoter le côté gauche de la carte de manière à libérer le connecteur.
Figure 3-5. Installation d'un disque dur SATA dans un support de lecteur SATA 2 1 3 1 vis (4) 3 disque dur SATA. 2 support de disque dur SATA Installation d'un disque dur SATA et d'une carte intermédiaire dans un support SATAu REMARQUE : pour installer un disque dur SATA dans un support SATAu, vous devez préalablement fixer une carte intermédiaire à l'arrière du disque.
2 En disposant l'assemblage tel qu'il est représenté à la Figure 3-6, faites correspondre le trou arrière inférieur du disque dur à celui marqué « SATAu » sur le support. Si la position est correcte, l'arrière du disque dur doit être au même niveau que l'arrière du support. 3 Fixez le disque dur sur le support à l'aide des quatre vis. Reportez-vous à la Figure 3-6.
Figure 3-6.
Blocs d'alimentation Le système prend en charge un ou deux blocs d'alimentation d'une puissance de sortie de 750 W. Si le système comprend un seul bloc d'alimentation, celuici doit être installé dans la baie de gauche (1). Si deux blocs sont installés, le second est utilisé comme source d'alimentation redondante enfichable à chaud. AVIS : si un seul bloc d'alimentation est installé, vous devez installer un cache sur la baie vide pour assurer un refroidissement correct du système.
4 Poussez vers la droite la patte de verrouillage située à gauche du bloc d'alimentation, afin de la débloquer. Faites pivoter la poignée jusqu'à ce que le bloc d'alimentation se dégage du châssis. Reportez-vous à la Figure 3-7. 5 Soulevez le bloc d'alimentation pour le retirer du châssis. Figure 3-7.
3 Faites passer le cordon d'alimentation dans le support de fixation, connectez-le au bloc d'alimentation et branchez l'autre extrémité sur une prise de courant. REMARQUE : après avoir installé un nouveau bloc d'alimentation, patientez quelques secondes pour que le système reconnaisse ce module et détermine s'il fonctionne correctement. Le voyant du bloc d'alimentation s'allume en vert si le bloc d'alimentation fonctionne normalement. Reportez-vous à la Figure 1-4.
PRÉCAUTION : attendez que les lames du ventilateur se soient arrêtées pour le manipuler. 2 Relevez la poignée du ventilateur et tirez ce dernier vers le haut hors de son boîtier pour le dégager du châssis. Reportez-vous à la Figure 3-8. Figure 3-8.
Réinstallation d'un ventilateur 1 Vérifiez que la poignée du ventilateur est relevée et enfoncez ce dernier sur le bâti jusqu'à ce qu'il soit correctement emboîté. Abaissez la poignée du ventilateur jusqu'à ce que vous entendiez un déclic. Reportez-vous à la Figure 3-8. 2 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73. Carénage de refroidissement Le carénage de refroidissement produit un flux d'air qu'il dirige sur les modules de mémoire du système.
Figure 3-9. Installation et retrait du carénage de refroidissement 3 2 1 4 5 1 pivots du carénage (2) 2 carénage de refroidissement 3 loquet d'éjection 4 charnières du carénage (2) 5 support de ventilateur Installation du carénage de refroidissement 1 Alignez les charnières sur les pivots du carénage, qui sont situés de chaque côté du support de ventilateur. Reportez-vous à la Figure 3-9.
Supports de ventilateur Retrait du support de ventilateur PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur. 2 Ouvrez le système. Reportez-vous à la section « Ouverture du système », à la page 72.
Figure 3-10. Retrait et installation du support de ventilateur 3 2 4 1 5 1 loquet d'éjection 2 support de ventilateur 3 clip en plastique 4 emplacement du support de ventilateur dans le bâti des blocs d'alimentation 5 pattes (2) Réinstallation du support de ventilateur 1 Insérez les deux pattes situées à droite du support de ventilateur dans les emplacements correspondants, sur le plateau de la carte système.
5 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73. 6 Rebranchez le système à la prise secteur et allumez-le, ainsi que les périphériques connectés. Carte contrôleur fille SAS La carte latérale du système comprend un logement réservé à l'installation d'une carte contrôleur fille SAS. La carte contrôleur fille SAS fournit un soussystème de stockage SAS aux disques durs internes du système. La carte contrôleur fille SAS est représentée à la Figure 3-11.
Figure 3-11. Installation d'une carte contrôleur fille SAS 3 2 1 4 6 5 1 carte contrôleur fille SAS 2 carte contrôleur fille SAS 3 patte de dégagement 4 connecteurs SAS 0 et 1 en face des connecteurs de fond de panier SAS_A et SAS_B 5 orifices sur le châssis (2) 6 Carte contrôleur fille SAS 6 Reliez tous les câbles de la carte contrôleur fille SAS au fond de panier.
Instructions de câblage de la carte contrôleur fille SAS Figure 3-12. pouces x 4 Câblage de la carte contrôleur fille SAS avec le fond de panier 3,5 2 3 1 4 5 1 contrôleur SAS 0 2 carte contrôleur SAS?fille 3 contrôleur SAS 1 4 fond de panier SAS A 5 fond de panier 3,5 pouces x 4 Retrait d'une carte contrôleur fille SAS 1 Débranchez le câble du panneau de commande. Reportez-vous à la section « Retrait de l'assemblage du panneau de commande », à la page 125.
Configuration du périphérique d'amorçage REMARQUE : le démarrage du système à partir d'un périphérique externe connecté à une carte SAS ou SCSI n'est pas pris en charge. Consultez le site support.dell.com pour obtenir les informations les plus récentes concernant le démarrage à partir de périphériques externes. Si vous envisagez de démarrer le système à partir d'un disque dur, celui-ci doit être relié au contrôleur principal (d'amorçage).
Installation d'une carte d'extension PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. REMARQUE : la procédure utilisée pour installer les cartes d'extension dans les cartes de montage de gauche et centrale est la même.
Figure 3-13. Installation d'une carte d'extension 3 4 5 2 1 1 guide d'alignement avant 2 connecteur de carte d'extension 3 connecteur latéral 4 carte d'extension 5 loquet du guide de la carte d'extension 6 Connectez tous les câbles requis pour la nouvelle carte. Consultez la documentation fournie avec la carte pour obtenir des informations sur la connexion des câbles. 7 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73.
1 Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur. 2 Ouvrez le système. Reportez-vous à la section « Ouverture du système », à la page 72. 3 Déconnectez tous les câbles de la carte d'extension. 4 Dégagez la carte d'extension : a Ouvrez le loquet de la carte d'extension. Reportez-vous à la Figure 3-13. b Tenez la carte d'extension par les coins supérieurs et retirez-la du connecteur avec précaution.
3 Déconnectez tous les câbles de la carte d'extension. 4 Retirez toutes les cartes d'extension du boîtier. Reportez-vous à la section « Retrait d'une carte d'extension », à la page 95. 5 Appuyez sur les deux loquets de dégagement bleus du boîtier de cartes d'extension. Reportez-vous à la Figure 3-14. Figure 3-14.
Réinstallation du boîtier de cartes d'extension PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Alignez les guides situés de chaque côté du boîtier de cartes d'extension sur les broches de la carte système, puis mettez le boîtier en place. Reportez-vous à la Figure 3-14. 2 Installez toutes les cartes d'extension.
Figure 3-15. Installation d'une carte DRAC 2 3 4 5 1 6 1 connecteurs de carte DRAC (2) 2 câbles de carte DRAC (2) 3 orifice du picot de fixation 4 carte DRAC 5 obturateur de prise 6 orifices des picots de support (2) 6 Alignez le bord avant de la carte DRAC sur les deux picots de fixation avant en plastique, qui se trouvent à côté du connecteur de DRAC de la carte système. Appuyez sur le côté de la carte jusqu'à ce qu'elle soit correctement emboîtée. Reportez-vous à la Figure 3-15.
7 Reliez la carte DRAC à la carte système à l'aide des deux câbles rubans courts. Reportez-vous à la Figure 6-2 pour identifier les emplacements des connecteurs. AVIS : lorsque vous enfichez des câbles, veillez à ne pas endommager les composants adjacents de la carte système. a Branchez un câble sur le connecteur 1 de la carte DRAC et sur le connecteur DRAC_CONN1 de la carte système. b Branchez le second câble sur le connecteur 2 de la carte DRAC et sur le connecteur DRAC_CONN2 de la carte système.
2 Retirez le cadre. Reportez-vous à la section « Retrait du cadre avant », à la page 71. 3 Ouvrez le système. Reportez-vous à la section « Ouverture du système », à la page 72. 4 Déconnectez le câble du lecteur optique de l'arrière du lecteur. 5 Pour retirer le lecteur optique, appuyez sur la patte de dégagement bleue, puis faites glisser le plateau hors du système. Reportez-vous à la Figure 3-16. Figure 3-16.
4 Retirez le carénage de refroidissement. Reportez-vous à la section « Retrait du carénage de refroidissement », à la page 86. 5 Retirez le support de retention de câble de la paroi interne droite du châssis. Appuyez sur le loquet d'éjection bleu et sur la languette vers l'avant du système jusqu'à ce que la languette sorte des logements du châssis. 6 Acheminez le câble SATA dans le conduit pour câble situé sur la paroi droite du châssis et remettez le support de câble en place.
Mémoire système Vous pouvez mettre la mémoire du système à niveau à 16 Go maximum en installant des modules de mémoire DDR II de 667 MHz FB (mises en tampon) par lots de 1 Go ou 2 Go. Les huit emplacements mémoire se trouvent sur la carte système, sous le carénage de refroidissement placé à côté des baies d'alimentation. Reportez-vous à la Figure 6-2. Vous pouvez vous procurer des kits d'extension de mémoire auprès de Dell.
• Les modules FB DIMM doivent être installés par paires de taille, vitesse et technologie identiques. Leur nombre total doit être de deux, quatre ou huit. Pour optimiser les performances du système, ces quatre ou huit modules doivent être de taille, vitesse et technologie identiques. • La mise en miroir de la mémoire et l'utilisation d'une mémoire de réserve requièrent 8 modules FB DIMM de même taille, vitesse et technologie. • Ces deux fonctionnalités ne peuvent pas être implémentées en même temps.
Tableau 3-1. Configurations pour l'utilisation d'une mémoire de réserve ( s u i t e ) Modules Taille/Type de mémoire Mémoire totale Disponible Lecteur de rechange 8 2 Go, une rangée de connexions 16 Go 8 Go 8 Go 8 2 Go, double rangée de connexions 16 Go 12 Go 4 Go Prise en charge de la mise en miroir de la mémoire Le système prend en charge la mise en miroir de la mémoire s'il est équipé de huit modules de mémoire identiques.
PRÉCAUTION : les modules DIMM restent chauds un certain temps après la mise hors tension du système. Si vous devez les manipuler, attendez qu'ils refroidissent. Tenez-les par les bords en évitant de toucher leurs composants. 5 Appuyez sur les pattes d'éjection du support de module de mémoire, puis écartez-les (reportez-vous à la Figure 3-18) pour pouvoir insérer le module dans le support. Figure 3-18.
9 Réinstallez le carénage de refroidissement de la mémoire. Reportez-vous à la section « Installation du carénage de refroidissement », à la page 87. AVIS : ne faites jamais fonctionner le système si le carénage de refroidissement de la mémoire a été retiré. Le système pourrait surchauffer rapidement et s'arrêter, entraînant une perte de données. 10 Refermez le système. Reportez-vous à la section « Ouverture du système », à la page 72.
4 Repérez les supports des modules de mémoire sur la carte système. Reportez-vous à la Figure 6-2. PRÉCAUTION : les modules DIMM restent chauds un certain temps après la mise hors tension du système. Si vous devez les manipuler, attendez qu'ils refroidissent. Tenez-les par les bords en évitant de toucher leurs composants. 5 Poussez les pattes d'éjection situées de chaque côté du support vers le bas et vers l'extérieur pour extraire le module de mémoire. Reportez-vous à la Figure 3-18.
1 Avant de mettre le système à niveau, téléchargez la version du BIOS système la plus récente disponible sur le site support.dell.com. 2 Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur. 3 Ouvrez le système. Reportez-vous à la section « Ouverture du système », à la page 72. 4 Retirez les ventilateurs. Reportez-vous à la section « Retrait d'un ventilateur du système », à la page 84. 5 Retirez le support du ventilateur.
Figure 3-19. Installation et retrait du dissipateur de chaleur 1 2 3 1 dissipateur de chaleur 3 loquet du levier de fixation 2 leviers de fixation du dissipateur de chaleur (2) 7 Attendez 30 secondes pour que le dissipateur de chaleur se détache du processeur. 8 Ouvrez l'autre levier de fixation du dissipateur de chaleur.
11 Relevez le levier d'éjection de 90 degrés jusqu'à ce que le processeur sorte de son support. Reportez-vous à la Figure 3-20. 12 Relevez le cadre de protection pour dégager le processeur. Figure 3-20. Installation et retrait d'un processeur 1 2 3 6 4 5 1 encoche du processeur (2) 2 processeur 3 levier d'éjection du support 4 cadre de protection du processeur 5 support ZIF 6 repère (2) 13 Sortez le processeur et laissez le levier relevé afin de pouvoir installer le nouveau processeur.
AVIS : le fait de remettre le système sous tension alors que le processeur est mal positionné risque de provoquer des dommages irréparables, à la fois pour le processeur et pour la carte système. Lorsque vous insérez le processeur dans le support, prenez garde à ne pas tordre les broches de ce dernier. a Si ce n'est déjà fait, redressez complètement le levier d'éjection. b Une fois le p rocesseur aligné sur les repères, insérez-le dans le support avec précaution.
6 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73. Lorsque le système démarre, il détecte la présence du nouveau processeur et modifie automatiquement les informations du programme de configuration du système. 7 Appuyez sur pour accéder au programme de configuration du système et vérifier que les informations relatives au processeur correspondent bien à la nouvelle configuration.
AVIS : si vous sortez la pile de son support avec un objet non pointu, prenez garde de ne pas toucher la carte système. Vérifiez que l'objet est inséré entre la pile et son support avant de tenter d'extraire la pile. Sinon, vous risqueriez d'endommager la carte système en arrachant le support ou en brisant des éléments de circuit sur la carte système. AVIS : pour ne pas endommager le connecteur de pile, maintenez-le en place lorsque vous installez ou retirez une pile. 4 Retirez la pile du système.
6 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73. 7 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. 8 Accédez au programme de configuration du système pour vérifier que la batterie fonctionne correctement. Reportez-vous à la section « Accès au programme de configuration du système », à la page 49. 9 Entrez l'heure et la date exactes dans les champs Heure et Date du programme de configuration du système.
5 Retirez la plaque de la carte de montage : a Tirez sur la broche de dégagement de la carte de montage. Reportez-vous à la section Figure 3-22. b Simultanément, retirez la carte de montage des ouvertures de cartes d'extension. c Soulevez la carte de montage pour la dégager des six pattes de fixation. Figure 3-22.
Installation de la carte de montage de gauche PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Placez la carte de montage dans le bâti, en faisant en sorte que les six pattes de fixation s'insèrent dans les encoches correspondantes. Reportezvous à la Figure 3-22.
Figure 3-23. Réinstallation de la carte de montage centrale 2 3 1 4 5 1 guide de la carte (2) 2 patte de dégagement 3 carte de montage centrale 4 broches d'alignement (2) 5 support de la carte système Installation de la carte de montage centrale 1 Alignez les deux broches de la carte système sur les guides de la carte de montage, puis enfoncez cette dernière jusqu'à ce que son connecteur soit complètement inséré dans le logement de la carte système. Reportez-vous à la Figure 3-23.
Carte latérale Retrait de la carte latérale PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur. 2 Ouvrez le système. Reportez-vous à la section « Ouverture du système », à la page 72.
Figure 3-24.
Installation de la carte latérale PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Mettez le système et les périphériques connectés hors tension, puis débranchez le système de la prise secteur.
5 Débranchez le(s) câble(s) SAS et le câble du panneau de commande de leurs connecteurs respectifs, sur le fond de panier. Reportez-vous aux sections « Instructions de câblage de la carte contrôleur fille SAS », à la page 92 et « Retrait de l'assemblage du panneau de commande », à la page 125. 6 Le cas échéant, retirez la carte contrôleur de stockage fille. Reportez-vous à la section « Retrait d'une carte contrôleur fille SAS », à la page 92. 7 Retirez le carénage de ventilation.
Figure 3-25. Retrait de la carte de fond de panier SAS 2 3 4 1 5 1 support de disque 2 broche de dégagement de la carte de fond de panier SAS 3 carte de fond de panier SAS 4 logements de fixation (10) 5 pattes de fixation (10) Installation de la carte de fond de panier SAS PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
4 Réinstallez le support de ventilateur. Reportez-vous à la section « Réinstallation du support de ventilateur », à la page 89. 5 Réinstallez les ventilateurs. Reportez-vous à la section « Réinstallation d'un ventilateur », à la page 86. 6 Réinstallez le carénage de ventilation. Reportez-vous à la section « Installation du carénage de refroidissement », à la page 87. 7 Réinstallez la carte contrôleur SAS?fille. Reportez-vous à la section « Installation d'une carte contrôleur fille SAS », à la page 90.
Assemblage du panneau de commande (procédure réservée à la maintenance) REMARQUE : l'assemblage du panneau de commande se compose de deux modules distincts : le module d'affichage et la carte du panneau de commande. Utilisez les instructions suivantes pour retirer et installer chaque module. Retrait de l'assemblage du panneau de commande PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
Figure 3-26. Retrait du panneau de commande 5 4 6 3 1 2 7 1 étiquette du module d'affichage 2 vis de fixation du module d'affichage (2) 3 module d'affichage 4 câble du module d'affichage 5 câble du panneau de commande 6 carte du circuit du panneau de commande 7 vis de fixation de la carte du panneau de commande (3) Installation de l'assemblage du panneau de commande 1 Insérez le module d'affichage dans l'ouverture du châssis et fixez-le à l'aide des deux vis Torx.
4 Enfichez le câble du module d'affichage dans la carte du panneau de commande. Reportez-vous à la Figure 3-26. 5 Connectez le câble du panneau de commande à la carte du panneau de commande. Reportez-vous à la Figure 3-26. 6 Refermez le système. Reportez-vous à la section « Fermeture du système », à la page 73. 7 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés. 8 Installez le cadre, le cas échéant.
PRÉCAUTION : Les modules DIMM restent chauds un certain temps après la mise hors tension du système. Si vous devez les manipuler, attendez qu'ils refroidissent. Tenez-les par les bords en évitant de toucher leurs composants. 9 Retirez les modules de mémoire. Reportez-vous à la section « Retrait de modules de mémoire », à la page 107. REMARQUE : Lorsque vous retirez les modules de mémoire, notez l'emplacement de chacun afin de pouvoir ensuite les réinstaller correctement.
Figure 3-27.
Installation de la carte système PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Abaissez le plateau de la carte système jusqu'à ce qu'il soit posé à plat au fond du châssis. 2 Vérifiez que les 17 pattes de fixation de la carte système sont correctement insérées dans les logements correspondants.
Dépannage du système La sécurité d'abord, pour vous et pour le système Pour effectuer certaines des procédures décrites dans ce document, vous devez retirer le capot du système et intervenir à l'intérieur. Lorsque vous intervenez sur le système, suivez scrupuleusement les opérations décrites dans ce guide ou dans une autre documentation accompagnant le système. PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
Tableau 4-1. Indications fournies par la procédure de démarrage (suite) Observez/écoutez : Action Comportement du voyant d'activité du lecteur de CD. Reportez-vous à la section « Dépannage d'un lecteur optique », à la page 147. Comportement du voyant d'activité du disque dur. Reportez-vous à la section « Dépannage d'un disque dur », à la page 149. Un bruit inhabituel de raclement Reportez-vous à la section « Obtention d'aide », ou de grincement constant lorsque à la page 173.
Tableau 4-2.
Action 1 Vérifiez les branchements du moniteur (prise secteur et raccordement au système). 2 Déterminez si le système comporte une carte d'extension équipée d'un connecteur de sortie vidéo. Si tel est le cas, le câble du moniteur doit être branché sur le connecteur de la carte d'extension, et non sur le connecteur vidéo intégré du système. Pour vérifier que le moniteur est relié au connecteur approprié, mettez le système hors tension, attendez une minute, puis reliez le moniteur à l'autre connecteur vidéo.
Action 1 Accédez au programme de configuration du système et vérifiez que les ports USB sont activés. Reportez-vous à la section « Utilisation du programme de configuration du système », à la page 49. 2 Examinez le clavier et son câble pour voir s'ils sont endommagés. 3 Remplacez le clavier défectueux par un clavier fiable. Si l'incident est résolu, remplacez le clavier défectueux. Reportez-vous à la section « Obtention d'aide », à la page 173. 4 Exécutez le test de diagnostic en ligne approprié.
3 Remplacez la souris défectueuse par une souris fiable. Si l'incident est résolu, remplacez la souris défectueuse. Reportez-vous à la section « Obtention d'aide », à la page 173. 4 Accédez au programme de configuration du système et vérifiez que le port USB est activé. Reportez-vous à la section « Utilisation du programme de configuration du système », à la page 49. Si l'incident persiste, reportez-vous à la section « Obtention d'aide », à la page 173.
Action 1 Mettez le système et les périphériques connectés au port série hors tension. 2 Remplacez le câble d'interface série par un câble fiable, puis mettez le système et le périphérique série sous tension. Si l'incident est résolu, remplacez le câble d'interface. 3 Mettez le système et le périphérique série hors tension, puis remplacez ce dernier par un périphérique similaire. 4 Mettez le système et le périphérique série sous tension. Si l'incident est résolu, remplacez le périphérique série.
6 Éteignez le système et le périphérique USB et remplacez ce dernier par un périphérique similaire. 7 Allumez le système et le périphérique USB. Si l'incident est résolu, remplacez le périphérique USB. Reportez-vous à la section « Obtention d'aide », à la page 173. Si le problème persiste, reportez-vous à la section « Obtention d'aide », à la page 173. Dépannage d'une carte NIC Problème • La carte NIC ne parvient pas à communiquer avec le réseau.
5 Vérifiez que les NIC, les concentrateurs et les commutateurs du réseau sont tous réglés sur la même vitesse de transmission des données. Consultez la documentation du matériel réseau. 6 Vérifiez que tous les câbles réseau sont du type approprié et qu'ils ne dépassent pas la longueur maximum. Reportez-vous au câblage réseau requis dans le Guide de mise en route. Dépannage d'un système mouillé Problème • Liquide répandu sur le système. • Excès d'humidité.
7 Si le système démarre normalement, arrêtez-le et réinstallez les cartes d'extension que vous avez retirées. Reportez-vous à la section « Installation d'une carte d'extension », à la page 94. 8 Exécutez le test de diagnostic en ligne approprié. Reportez-vous à la section « Utilisation des diagnostics de Server Administrator », à la page 157. Si les tests échouent, reportez-vous à la section « Obtention d'aide », à la page 173.
Dépannage de la batterie du système Problème • Un message du système indique un problème de batterie. • Le programme de configuration du système perd les informations. • La date et l'heure du système se dérèglent constamment. REMARQUE : si le système reste hors tension longtemps (pendant des semaines ou des mois), la NVRAM peut perdre ses informations de configuration. Cette situation est causée par une batterie défectueuse.
Dépannage des blocs d'alimentation Problème • Les voyants d'état du système sont orange. • Les voyants de panne des blocs d'alimentation sont orange. • L'écran LCD du panneau avant indique qu'un incident lié aux blocs d'alimentation s'est produit. Action PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système.
4 Observez les voyants pour voir si l'incident est résolu. Si tel n'est pas le cas, retirez le bloc d'alimentation défectueux. Reportez-vous à la section « Retrait d'un bloc d'alimentation », à la page 82. 5 Installez un nouveau bloc d'alimentation. Reportez-vous à la section « Réinstallation d'un bloc d'alimentation », à la page 83. Si le problème persiste, reportez-vous à la section « Obtention d'aide », à la page 173.
Action PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Exécutez le test de diagnostic approprié. Reportez-vous à la section « Utilisation des diagnostics de Server Administrator », à la page 157. 2 Ouvrez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72.
Dépannage de la mémoire système Problème • Module de mémoire défectueux. • Carte système défectueuse. • L'écran LCD du panneau avant indique qu'un incident lié à la mémoire système s'est produit. Action PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Exécutez le test de diagnostic en ligne approprié.
9 Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques connectés. 10 Accédez au programme de configuration du système et vérifiez le paramètre de la mémoire système. Reportez-vous à la section « Utilisation du programme de configuration du système », à la page 49.
Dépannage d'un lecteur optique Problème • Le système ne peut pas lire les données d'un CD ou d'un DVD placé dans le lecteur. • Le voyant du lecteur optique ne clignote pas au démarrage du système. Action PRÉCAUTION : seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes. Avant de commencer cette procédure, lisez les consignes de sécurité fournies avec le système. 1 Essayez un autre CD ou DVD fiable.
Dépannage d'un lecteur de bande SCSI externe Problème • Lecteur de bande défectueux • Cartouche défectueuse • Logiciel de sauvegarde sur bande ou pilote du lecteur de bande manquant ou altéré • Contrôleur SCSI défectueux Action 1 Retirez la cartouche que vous utilisiez lorsque l'incident s'est produit et remplacez-la par une autre cartouche fiable. 2 Assurez-vous que les pilotes SCSI requis pour le lecteur de bande sont correctement installés et configurés.
9 Ouvrez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72. 10 Vérifiez que la carte contrôleur SCSI est correctement emboîtée dans son connecteur. Reportez-vous à la section « Installation d'une carte d'extension », à la page 94. 11 Refermez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72. 12 Rebranchez le système sur la prise secteur et allumez-le, ainsi que les périphériques connectés.
3 Si l'incident concerne plusieurs disques durs, passez à l'étape 7. S'il concerne un seul disque dur, passez à l'étape suivante. 4 Mettez le système hors tension, remboîtez le disque dur dans son logement et redémarrez le système. 5 Si le système est équipé d'une carte contrôleur RAID SAS fille, effectuez les étapes suivantes. a Redémarrez le système et appuyez sur pour ouvrir l'utilitaire de configuration de l'adaptateur hôte.
Dépannage d'une carte contrôleur fille SAS REMARQUE : pour dépanner une carte contrôleur fille SAS, reportez-vous également à sa documentation et à celle du système d'exploitation. Problème • Un message d'erreur signale un incident lié à la carte contrôleur fille SAS. • La carte contrôleur fille SAS ne fonctionne pas correctement ou pas du tout. Action PRÉCAUTION : seuls les techiniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
8 Vérifiez que la carte contrôleur est correctement insérée dans son connecteur. Reportez-vous à la section « Carte contrôleur fille SAS », à la page 90. 9 Vérifiez le câblage entre le ou les fonds de panier SAS et la carte contrôleur SAS fille. Reportez-vous à la section « Installation d'une carte contrôleur fille SAS », à la page 90. 10 Vérifiez que les câbles sont correctement connectés à la carte contrôleur SAS fille et au fond de panier SAS. 11 Refermez le système.
4 Ouvrez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72. 5 Vérifiez que chaque carte d'extension est correctement emboîtée dans son connecteur. Reportez-vous à la section « Installation d'une carte d'extension », à la page 94. 6 Refermez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72. 7 Rebranchez le système à la prise secteur et mettez-le sous tension, ainsi que les périphériques connectés.
Dépannage des microprocesseurs Problème • Un message d'erreur signale un incident lié au processeur. • L'écran LCD du panneau avant indique qu'un incident lié aux processeurs ou à la carte système s'est produit. • Un dissipateur de chaleur n'est pas installé pour chaque processeur. Action PRÉCAUTION : seuls les techiniciens de maintenance qualifiés sont habilités à retirer le capot du système pour accéder aux composants internes.
10 Retirez le processeur 2 et ne laissez que le processeur 1 installé. Reportezvous à la section « Processeurs », à la page 108. Pour identifier l'emplacement des processeurs, reportez-vous à la Figure 6-2. Si un seul processeur est installé, reportez-vous à la section « Obtention d'aide », à la page 173 . 11 Refermez le système. Reportez-vous à la section « Ouverture et fermeture du système », à la page 72.
Dépannage du système
Exécution des diagnostics du système Si vous rencontrez des problèmes lors de l’utilisation du système, lancez les diagnostics avant de demander une assistance technique. Le but des diagnostics est de tester le matériel du système sans nécessiter d'équipement supplémentaire et sans risque de perte de données. Si vous ne réussissez pas à corriger le problème, le personnel de service et de support peut s'aider des résultats des tests de diagnostic pour vous aider à le résoudre.
• Interrompre temporairement un test quand une erreur est détectée ou l'arrêter lorsqu'une limite d'erreur définie par l'utilisateur est atteinte. • Afficher des messages d'aide qui décrivent brièvement chaque test et ses paramètres. • Afficher des messages d'état qui vous indiquent si les tests ont abouti. • Afficher des messages d'erreur qui vous indiquent si des problèmes sont survenus pendant les tests.
Options de test des diagnostics du système Cliquez sur l'option de test voulue dans la fenêtre Main Menu (Menu principal). Le Tableau 5-1 explique brièvement le fonctionnement des options de test disponibles. Tableau 5-1. Options de test des diagnostics du système Option de test Fonction Express Test (Test rapide) Effectue une vérification rapide du système. Cette option exécute les tests de périphériques qui ne requièrent pas d'action de l'utilisateur.
Sélection d'options de diagnostic Le champ Diagnostics Options (Options de diagnostic) permet de sélectionner la façon dont le périphérique sera testé. Vous pouvez définir les options suivantes : 160 • Non-Interactive Tests Only (Tests non interactifs uniquement) : cette option permet d'exécuter uniquement les tests ne nécessitant aucune intervention de l'utilisateur.
Visualisation des informations et des résultats Les onglets de la fenêtre Customize (Personnaliser) contiennent des informations sur les tests et les résultats. Les onglets suivants sont disponibles : • Results (Résultats) : indique le test exécuté et son résultat. • Errors (Erreurs) : affiche les erreurs qui se sont produites pendant le test. • Help (Aide) : affiche des informations sur le périphérique, le composant ou le test sélectionné.
Exécution des diagnostics du système
Cavaliers et connecteurs Cette section contient des informations spécifiques concernant les cavaliers du système. Elle décrit également les connecteurs se trouvant sur les cartes du système. Cavaliers de la carte système La Figure 6-1 présente l'emplacement des cavaliers de configuration sur la carte système.Le Tableau 6-1 répertorie les paramètres des cavaliers.
Figure 6-1.
Tableau 6-1. Réglages des cavaliers de la carte système Cavalier 1 PWRD_EN Paramètre Description (par défaut) La fonction de mot de passe est activée. La fonction de mot de passe est désactivée. 2 NVRAM_CLR (par défaut) Les paramètres de configuration sont conservés au démarrage du système. Les paramètres de configuration sont effacés au prochain démarrage du système.
Figure 6-2.
Tableau 6-2.
Connecteurs de la carte de fond de panier SAS La Figure 6-3 montre l'emplacement des connecteurs sur la carte de fond de panier SAS. Figure 6-3.
Connecteurs de la carte latérale Reportez-vous à la Figure 6-4 pour connaître l'emplacement des connecteurs de la carte latérale et consulter la description de ces connecteurs. Figure 6-4.
Figure 6-5. Composants de la carte de montage de gauche pour cartes d'extension PCIe (en option) 1 2 3 4 5 1 broche de dégagement de la carte de montage 2 largeur LANE de logement PCIe 2 (x 8) 3 largeur LANE de logement PCIe 3 (x 4) 4 guide de broche (2) 5 connecteur de la carte système Figure 6-6.
Désactivation d'un mot de passe oublié Les fonctionnalités logicielles de protection du système comprennent un mot de passe système et un mot de passe de configuration, qui sont présentés en détail dans la section « Utilisation du programme de configuration du système », à la page 49. Le cavalier de mot de passe active ces fonctions ou les désactive, et efface le(s) mot(s) de passe utilisé(s).
12 Rebranchez le système et les périphériques sur les prises secteur, puis allumez le système. 13 Attribuez un nouveau mot de passe système et/ou de configuration. Pour attribuer un nouveau mot de passe à l'aide du programme de configuration du système, reportez-vous à la section « Attribution d'un mot de passe système », à la page 63.
Obtention d'aide Contacter Dell Aux États-Unis, appelez le 800-WWW-DELL (800-999-3355). REMARQUE : si vous ne disposez pas d'une connexion Internet active, vous pouvez utiliser les coordonnées figurant sur votre preuve d'achat, votre bordereau de livraison, votre facture ou encore sur le catalogue des produits Dell. Dell fournit plusieurs options de service et de support en ligne et par téléphone.
Obtention d'aide
Glossaire Cette section définit ou identifie les termes techniques, abréviations, acronymes et sigles utilisés dans la documentation fournie avec le système. A : ampère. ACPI : acronyme de « Advanced Configuration and Power Interface », interface de configuration et d'alimentation avancée. Interface standard qui permet au système d'exploitation de contrôler les paramètres relatifs à la configuration et à la gestion de l'alimentation.
BTU : acronyme de « British Thermal Unit », unité thermique britannique. bus : chemin d'informations entre les différents composants du système. Le système contient un bus d'extension qui permet au processeur de communiquer avec les contrôleurs des différents périphériques connectés au système. Il contient également un bus d'adresse et un bus de données pour les communications entre le microprocesseur et la RAM.
combinaison de touches : commande exécutée lorsque l'utilisateur appuie sur plusieurs touches en même temps (exemple : ). composant : dans le contexte de l'interface DMI, il s'agit d'un élément compatible DMI, comme un système d'exploitation, un ordinateur, une carte d'extension ou un périphérique. Chaque composant est constitué de groupes et d'attributs définis comme caractéristiques de ce composant.
DRAC : acronyme de « Dell Remote Access Controller », contrôleur d'accès à distance Dell. DRAM : acronyme de « Dynamic Random-Access Memory », mémoire vive dynamique. Normalement, la mémoire vive d'un système est composée entièrement de puces DRAM. DVD : acronyme de « Digital Versatile Disc », disque numérique polyvalent. ECC : acronyme de « Error Checking and Correction », vérification et correction d'erreurs.
Gb : gigabit ; 1 024 mégabits, soit 1 073 741 824 bits. Go : giga-octet ; 1 024 méga-octets, soit 1 073 741 824 octets. La mesure est souvent arrondie à 1 000 000 000 octets lorsqu'elle fait référence à la capacité d'un disque dur. groupe : dans le contexte de l'interface DMI, un groupe est une structure de données qui définit les informations courantes, ou attributs, d'un composant gérable.
lame : module équipé d'un processeur, de mémoire et d'un disque dur. Ces modules sont montés dans une baie qui dispose de blocs d'alimentations et de ventilateurs. LAN : acronyme de « Local Area Network », réseau local. Un LAN se limite normalement à un bâtiment ou à un groupe de bâtiments proches, où tout le l'équipement est relié par des câbles réservés au réseau LAN. lb : livre (poids). LCD : acronyme de « Liquid Crystal Display », écran à cristaux liquides.
mémoire vidéo : la plupart des cartes vidéo VGA et SVGA contiennent des puces de mémoire qui viennent s'ajouter à la RAM du système. L'espace mémoire vidéo installé affecte surtout le nombre de couleurs affichables par un programme (si les pilotes vidéo et la capacité de moniteur sont adéquats). MHz : mégahertz.
NMI : acronyme de « NonMaskable Interrupt », interruption non masquable. Un matériel envoie une NMI pour signaler des erreurs matérielles au processeur. ns : nanoseconde. NTFS : option du système de fichiers NT dans le système d'exploitation Windows 2000. numéro de service : code à barres qui se trouve sur le système et permet de l'identifier lorsque vous appelez le support technique de Dell.
pixel : point sur un écran vidéo. Les pixels sont disposés en lignes et en colonnes afin de créer une image. Une résolution vidéo, par exemple 640 x 480, indique le nombre de pixels en largeur et en hauteur. port en amont : port sur un commutateur ou un concentrateur réseau, qui sert à le relier à un autre commutateur ou concentrateur sans utiliser de câble croisé. port série : port d'E/S, utilisé le plus souvent pour connecter un modem au système.
répertoire : les répertoires permettent de conserver des fichiers apparentés sur un disque en les organisant hiérarchiquement dans une structure en « arborescence inversée ». Chaque disque possède un répertoire « racine ». Les répertoires supplémentaires qui partent du répertoire racine sont appelés sous-répertoires. Ces derniers peuvent contenir d'autres répertoires, formant une sous-arborescence.
SMART : acronyme de « Self-Monitoring Analysis and Reporting Technology », technologie de prévision des défaillances des lecteurs de disque. Cette technologie permet aux disques durs de signaler les erreurs et les pannes au BIOS du système, puis d'afficher un message d'erreur sur l'écran. SMP : acronyme de « Symmetric MultiProcessing », multi-traitement symétrique.
TOE : acronyme de « TCP/IP Offload Engine », moteur de décentralisation TCP/IP. UNIX : Universal Internet Exchange. UNIX est un système d'exploitation écrit en langage C. Il est le précurseur de Linux. UPS : acronyme de « Uninterruptible Power Supply », onduleur. Unité, alimentée par batterie, qui fournit automatiquement l'alimentation du système en cas de coupure de courant. USB : acronyme de « Universal Serial Bus », bus série universel.
win.ini : fichier de démarrage du système d'exploitation Windows. Au démarrage de Windows, le système d'exploitation consulte le fichier win.ini afin de déterminer les options à utiliser dans l'environnement Windows. Ce fichier comprend généralement aussi des sections qui contiennent les paramètres facultatifs pour les programmes Windows installés sur le disque dur. XML : acronyme de « Extensible Markup Language ».
Glossaire
Index A acheminement de câbles SATA dans le PowerVault DL2000, 102 alerte messages, 47 alimentation voyant, 19 voyants, 19 assemblage du panneau de commande installation, 126 retrait, 125 assistance contacter Dell, 173 Boîtier de cartes d'extension Réinstallation, 98 boîtier de cartes d'extension retrait, 96 bus PCI carte de montage des cartes d'extension, 169 C Cache Bloc d'alimentation, 84 Disque dur, 75 Cache de bloc d'alimentation, 84 avertissement messages, 47 Cache de lecteur Installation, 76 Retr
Carte de fond de panier SAS Connecteurs, 168 Installation, 123 Retrait, 121 Cavaliers Carte système, 163 carte de montage centrale installation, 118 retrait, 117 configuration mémoire, 103 carte de montage de gauche installation, 117 retrait, 115 carte de montage des cartes d'extension bus PCI, 169 connecteurs, 169 carte fille SAS, 90, 92 Carte latérale Installation, 121 Retrait, 119 carte système cavaliers, 163 connecteurs, 165 installation, 130 remise en place, 127 retrait, 127 cartes d'extension cons
démarrage accès aux fonctions du système, 12 Dépannage Fonctions d'E-S de base, 136 Périphérique d'E/S série, 136 Ventilateur, 143 dépannage batterie, 141 blocs d'alimentation, 142 carte contrôleur fille SAS, 151 carte NIC, 138 cartes d'extension, 152 clavier, 134 connexions externes, 133 disque dur, 149 lecteur de bande, 148 lecteur de CD, 147 mémoire, 145 microprocesseurs, 154 périphérique USB, 137 refroidissement du système, 143 routine de démarrage, 131 souris, 135 système endommagé, 140 système mouillé
I Installation Cache de bloc d'alimentation, 84 Cache de disque dur, 76 Carte d'extension, 94 Carte de fond de panier SAS, 123 Carte latérale, 121 installation assemblage du panneau de commande, 126 carte de montage de gauche, 115 carte système, 130 consignes relatives à la mémoire, 103 consignes relatives aux cartes d'extension, 93 disque dur SATA dans un support SATA, 78 disque dur SATAu dans un support SATA, 79 disques durs, 76 lecteur optique, 101 mémoire, 105 processeur, 108, 111 Installation à chaud D
modules de mémoire retrait, 107 mot de passe désactivation, 171 mot de passe de configuration attribution, 66 modification, 67 utilisation, 66 mot de passe de configuration activé utilisation, 67 mot de passe système attribution, 63 modification, 65 suppression, 65 utilisation, 63 mots de passe configuration, 66 système, 63 N NIC voyants, 20 numéros de téléphone, 173 O options configuration du système, 50 P panneau arrière caractéristiques, 17 périphérique USB dépannage, 137 périphériques externes connex
remplacement pile du système, 113 souris dépannage, 135 Retrait Cache de bloc d'alimentation, 84 Cache de disque dur, 75 Capot, 72 Carte d'extension, 95 Carte de fond de panier SAS, 121 Carte latérale, 119 Disques durs, 76 Ventilateur, 84 support disque dur SATA (SATA), 78 disque dur SATAu (SATA), 79 retrait assemblage du panneau de commande, 125 batterie du système, 113 bloc d'alimentation, 82 boîtier de cartes d'extension, 96 cadre, 71 carte de montage de gauche, 115 carte système, 127 disque dur inst
V Ventilateur Dépannage, 143 ventilateurs remise en place, 86 retrait, 84 vérification du matériel, 132 vidéo dépannage, 133 Voyants Disque dur, 15 voyants carte NIC, 20 panneau arrière, 17 panneau avant, 13 Index 195
Index