Dell PowerVault DL Backup to Disk Appliance Powered by Symantec Backup Exec Benutzerhandbuch
Anmerkungen, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG liefert wichtige Informationen, mit denen Sie den Computer besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS macht darauf aufmerksam, dass bei Nichtbefolgung von Anweisungen eine Beschädigung der Hardware oder ein Verlust von Daten droht, und zeigt auf, wie derartige Probleme vermieden werden können.
Inhaltsverzeichnis Anmerkungen, Vorsichtshinweise und Warnungen................................................................2 Kapitel 1: Einführung......................................................................................................................7 Unterstützte Hardware und -software......................................................................................................................7 Zusätzliche Informationen..............................................................
Starten von Symantec Backup Exec......................................................................................................................23 Hinzufügen einer optionalen Bandbibliothek..........................................................................................................24 Hinzufügen des Bandgeräts zur Systemkonsole....................................................................................................24 Manuelle Konfiguration des Speichers..........................
Wiederherstellen nach dem Ausfall mehrerer Laufwerke...............................................................................43 Ersetzen von Laufwerken.................................................................................................................................43 Wiederherstellen des Systemlaufwerks mit IDR....................................................................................................44 Wiederherstellen des Appliance-Systemlaufwerks mit SDR......................
Neustarten der Backup Exec-Dienste für Backup Exec 2012..........................................................................64 Bestandsaufnahme und Katalogisierung der virtuellen Laufwerke.................................................................64 Wiederherstellen des Deduplizierung-Laufwerkspeichers aus einer Sicherungskopie.................................64 Importieren des DDS vom Laufwerkbuchstaben.............................................................................................
Einführung 1 Die Dell PowerVault DL Backup to Disk Appliance ist die neueste Generation des Backup-to-Disk-Schutzes der Symantec Backup Exec-Software.
• Bei Dokumenten und Wiederherstellungsmedien, auf die in diesem Dokument Bezug genommen wird, lesen Sie die Zusätzlichen Hinweise. • Eine Übersicht der unterstützten externen Laufwerke finden Sie in der Dell PowerVault MDxxxx-SystemSupport-Matrix auf der Website support.dell.com/manuals. Eine Liste mit unterstützten Bandgeräten, Firmware und Treiberversionen finden Sie in der Kompatibilitätsmatrix Dell PowerVault Compatibility Matrix unter www.dell.com/pvmatrix.
Einrichten des DL Backup to Disk-Systems 2 In den folgenden Abschnitten wird beschreiben, wie die Dell PowerVault DL Backup to Disk Appliance eingerichtet wird.
Verkabeln des Systems 1. Machen Sie die PowerVault DL2xxx- und PowerVault MDxxxx Getting Started Guides (Anleitung „Erste Schritte“) ausfindig, die mit dem System ausgeliefert wurden, und folgen Sie den Anweisungen zum Anschließen der Tastatur, der Netz- und Netzwerkkabel an das PowerVault DL2xxx-System. 2. Schließen Sie die Stromkabel an die einzelnen Speichergehäuse an. ANMERKUNG: Schalten Sie das PowerVault DL2xxx-System und die Speichergehäuse nicht ein.
Abbildung 2. Einstellen des Konfigurationsschalters für das PowerVault MD1200-Speichergehäuse 1. Konfigurationsschalter Anschließen des Speichergehäuses an das PowerVault DL2xxx-System Zum Anschließen des Speichergehäuses führen Sie einen der folgenden Schritte aus: 1. Schließen Sie das SAS-Datenkabel des auf dem PowerVault DL2xxx-System installierten PowerEdge RAIDControllers (PERC) an den primären EMM-SAS In-Anschluss am Speichergehäuse an. Abbildung 3.
Abbildung 4. Anschließen des SAS-Kabels vom PowerVault DL2xxx-System zum PowerVault MD1200-Speichergehäuse 1. PERC-Adapter 2. Primäres EMM ANMERKUNG: Wenn mehr als ein Speichergehäuse verwendet wird, schließen Sie den SAS-Out-Anschluss auf dem primären EMM an den SAS-In-Anschluss auf dem nächsten Gehäuse (in absteigender Reihenfolge) an. Lesen Sie im Dell PowerVault DL Backup to Disk Appliance Interoperability Guide (Dell Kompatibilitätshandbuch zum PowerVault DL Backup to Disk-System) unter support.dell.
Abbildung 5. Anschluss des PowerVault DL2xxx-Systems an das Speichergehäuse und die optionale Bandbibliothek ANMERKUNG: Wenn ein SCSI, SAS oder Fiber Channel Host Adapter für die Verwendung mit einem optionalen Bandgerät installiert wurde, lesen Sie das Thema „Hinzufügen einer optionalen Bandbibliothek“. ANMERKUNG: Schließen Sie keine Bandgeräte an den PERC-Adapter an. Betrachten Sie die Abbildung „Anschluss des SAS-Kabels vom PowerVault DL2xxx-System zum PowerVault MD1200-Speichergehäuse“.
1. Schalten Sie das System für die erstmalige Verwendung ein. 2. Melden Sie sich bei Microsoft Windows Server 2008 an. Der PowerVault DL Backup to Disk Appliance Configuration Wizard (Konfigurationsassistent für das PowerVault DL Backup to Disk-System) wird automatisch ausgeführt.
Standard In diesem Zustand konfiguriert die Backup-Anwendung die verfügbaren Laufwerke in dem PowerVault DL2xxx-System und optionalen Speichergehäusen und verwendet diese als Backup-Speicher. Sie können die Laufwerkskonfigurationsrichtlinie durch Auswählen einer der automatischen Einstellungen so einstellen, dass diese die verfügbaren Laufwerke automatisch konfiguriert. Lesen Sie dazu das Thema „Richtlinien zur Laufwerkkonfiguration“.
PowerVault MD1000 Speichergehäuse-Laufwerkkonfigurationen Das PowerVault MD1000 unterstützt nur SATA-Laufwerke. Die Standardkonfiguration besteht aus einem Hot-Spare in Steckplatz 0, einer Laufwerksgruppe, die die Steckplätze 1 bis 7 belegt und einer Laufwerksgruppe, die die Steckplätze 8 bis 14 belegt. Die automatische Laufwerkkonfiguration erstellt in jeder Laufwerksgruppe eines oder mehr virtuelle RAID 5-Laufwerke. Abbildung 7.
Die Standardkonfiguration mit zwei RAID 6 besteht aus einer Laufwerksgruppe, die die Steckplätze 0 bis 5 belegt und einer Laufwerksgruppe, die die Steckplätze 6 bis 11 belegt. Die automatische Laufwerkkonfiguration erstellt in jeder Laufwerksgruppe eines oder mehr virtuelle RAID 6-Laufwerke. Die Standardkonfiguration mit einzelnem RAID 6 besteht aus einer einzelnen Laufwerksgruppe, die die Steckplätze 0 bis 11 belegt.
Wenn Sie die manuelle Laufwerksrichtlinie wählen, lesen Sie das Thema „Starten von Symantec Backup Exec nach dem Konfigurieren des Systems“.
Eingeben von Lizenzschlüsseln für Versionen vor Backup Exec 2012 Backup Exec-Lizenzschlüssel sind erforderlich, um die Backup Exec-Optionen, die auf dem DL Backup to Disk-System installiert sind, zu aktivieren. ANMERKUNG: Bei Systemen, die mit Backup Exec 12.5 oder Backup Exec 2010 ausgeliefert werden, sich eventuell eine oder mehrere Lizenzen vorinstalliert. Geben Sie bei der Aufforderung durch Backup Exec zur Eingabe der Lizenzschlüssel nicht die vorinstallierten Lizenzen ein. 1.
Licenses on this Backup Exec Server (Optionen und Lizenzschlüssel auf diesem Backup Exec-Server installieren). Festlegen von Optionen in Symantec Backup Exec Standardmäßig installiert Backup Exec das System als unabhängigen Media-Server. Weitere Informationen finden Sie im Backup Exec Administrator’s Guide (Administratorhandbuch für Backup Exec) unter symantec.com. Die folgenden Optionen sind verfügbar: Unabhängiger Media-Server Dies ist der Standardserver, der von Symantec Backup Exec installiert wird.
Konfigurieren des PowerVault DL2xxx-Systems mit NIC-Teaming Die Broadcom Advanced Control Suite (BACS) ist auf dem System vorinstalliert. BACS wird verwendet, um Netzwerkkarten (NICs) auf dem PowerVault DL2xxx-System zu konfigurieren, zu verwalten und zu gruppieren. Zu den Vorteilen von Teaming gehören Lastverteilung des Datenverkehrs und Fehlertoleranz.
Verwenden der DL Backup to DiskSystemkonsole 3 Sie können die DL Backup to Disk Appliance Console (Dell PowerVault DL Backup to Disk-Systemkonsole) für Folgendes verwenden: • Verwalten des DL Backup to Disk Appliance • Starten der Symantec Backup Exec-Software • Anzeige von Systeminformationen • Systemstatusbericht • Anzeige des verfügbaren Laufwerksspeichers • Hinzufügen oder Entfernen von Bandgeräten • Konfigurieren der Netzwerk- und SNMP-Einstellungen ANMERKUNG: Nach dem Systemstart kann e
Hinzufügen einer optionalen Bandbibliothek Eine Liste mit unterstützten Bandgeräten finden Sie in der Dell PowerVault-Kompatibilitätsmatrix unter dell.com/ pvmatrix. Weitere Informationen zum ersten Einrichten und zur Konfiguration von Bandgeräten finden Sie in der Banddokumentation unter support.dell.com/manuals. Zum Hinzufügen einer Bandbibliothek führen Sie die folgenden Schritte aus: 1. Klicken Sie auf Launch Symantec Backup Exec (Symantec Backup Exec starten).
Das Fenster „Log On“ (Anmeldung) wird angezeigt. 3. Melden Sie sich mithilfe des Benutzernamens und des Kennworts, der bzw. das mithilfe des DL Backup to Disk Appliance Configuration Wizard (Konfigurationsassistenten des DL Backup to Disk-Systems) erstellt wurde, bei Server Administrator an.
ANMERKUNG: Sie können den Status des zu konfigurierenden virtuellen Laufwerks auf der Registerkarte Job Monitor (Job-Überwachung) in Backup Exec abfragen. Konvertieren der Speicherrolle von virtuellen Laufwerken Zum Konvertieren der Speicherrolle eines virtuelles Laufwerks von Backup to Disk zu Deduplizierung oder umgekehrt führen Sie die folgenden Schritte aus: 1. Unter Backup Exec 2012 oder aktueller navigieren Sie zur Registerkarte Storage (Speicher) in der Backup Exec Console.
wenn das System zum ersten Mal unter Verwendung des DL Backup to Disk Appliance Configuration Wizard (Konfigurationsassistent für das DL Backup to Disk-System) konfiguriert wird. ANMERKUNG: Nach der Auswahl der Standard-Laufwerkskonfiguration und der Konfiguration der automatischen Laufwerkskonfiguration für eines oder mehr virtuelle Laufwerke sollte diese Einstellung nicht geändert werden. Anderenfalls ändert sich der Status des Laufwerksubsystems von „standard“ (Standard) auf „advanced“ (erweitert).
PERC H800 • Die Nummer des ersten am Anschluss 1 des PERC 6/E-Adapters angeschlossenen Gehäuses lautet 3. Weitere an dieses Gehäuse angeschlossene Gehäuse erhalten entsprechend die Nummern 4 bzw. 5. • Die Nummer des ersten am Anschluss 0 des PERC H800-Adapters angeschlossenen Gehäuses lautet 0. Weitere am ersten der Reihe nach angeschlossene Gehäuse erhalten entsprechend die Nummern 1, 2 bzw. 3. • Die Nummer des ersten am Anschluss 1 des PERC H800-Adapters angeschlossenen Gehäuses lautet 4.
Aktualisieren der DL Backup to DiskSystemsoftware 4 Die DL Backup to Disk Appliance-Software wird regelmäßig aktualisiert, um Probleme zu beheben, die Performance zu verbessern, neue Funktionen einzuführen und um zusätzliche Hardware zu unterstützen. Es wird empfohlen, dass Sie diese Aktualisierungen übernehmen, um Ihr System weiterhin optimal zu betreiben.
finden Sie im Dell Update Packages for Microsoft Windows User's Guide (Benutzerhandbuch für Dell Aktualisierungspakete für Microsoft Windows) unter support.dell.com/manuals. Abonnieren der SystemsoftwareAktualisierungsbenachrichtigungen Technische Aktualisierungen von Dell, Abonnements, E-Mails mit wichtigen Produktwarnungen, Aktualisierungen von Dateien, Treibern und Dienstprogrammen für Ihr System. Um sich für diese Benachrichtigungen zu registrieren, gehen Sie zu support.dell.
von Backup Exec with LiveUpdate) im Symantec Backup Exec for Administrator's Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com.
Notfallwiederherstellung 5 Sie können die Dell PowerVault DL Backup to Disk Appliance nach einer Vielzahl von Hardware- oder Softwarefehlern wiederherstellen. Je nach Art des Problems können folgende Schritte notwendig sein: • • • • • • • Wiederherstellen nach einem Ausfall des internen Server-Laufwerks Wiederherstellen nach einem Laufwerkausfall des externen Speichergehäuses Neuinstallation des Betriebssystems.
Media“ (Konfigurieren und Verwenden virtueller Datenträger) im Integrated Dell Remote Access Controller 6 (iDRAC6) User Guide (Benutzerhandbuch zum Integrated Dell Remote Access Controller 6 (iDRAC6)) unter support.dell.com/ manuals. Planen der Notfallwiederherstellung mit IDR ANMERKUNG: Dieser Abschnitt gilt für DL-Systeme, die unter Backup Exec-Versionen vor Backup Exec 2012 ausgeführt werden.
Vorbereiten des Systems auf IDR Zum Konfigurieren von IDR auf dem System führen Sie die folgenden Schritte aus: 1. Vor der Konfiguration von IDR müssen Sie sicherstellen, dass alle internen und externen Speicher mit DSF konfiguriert wurden, wenn die Option Backup Exec Deduplication (Backup Exec-Deduplizierung) aktiviert und lizenziert wurde. 2.
12. Kopieren Sie dieses ISO-Image auf einen sicheren Speicherplatz auf einem anderen Computersystem. Wenn der startfähige IDR-Datenträger verloren gegangen ist oder während der Wiederherstellung nicht gelesen werden kann, können Sie auf der Basis dieses Images eine neue CD erstellen.
VORSICHT: Das PDDE_Volume ist der Bereitstellungspunkt des virtuellen DSF-Laufwerks, das durch die automatische Laufwerkskonfiguration erstellt wurde. Das Löschen dieses Ordners führt zum Verlust der DSFDaten. 5. Wählen Sie einen verfügbaren Speicherort für einen Backup to Disk-Ordner unter Destination (Ziel) → Device and Media (Geräte und Medien) aus. ANMERKUNG: Wählen Sie den DSF nicht als Ziel für das System-Backup aus. 6.
Weitere Informationen finden Sie unter Changing service account information (Ändern von Kontoinformationen für die Dienste) im Symantec Backup Exec Administrator’s Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com. 2. Ändern Sie das Kennwort für die Deduplizierungsdienste, wenn ein DSF auf dem System vorhanden ist. Führen Sie den folgenden Befehl in dem Verzeichnis C:\Programme\Symantec\Backup Exec\ aus: Spauser -c -u Benutzername.
das Thema „Übersicht der Lösungen zur Wiederherstellung”, und führen Sie die Schritte zur Wiederherstellung von nicht-IDR- oder nicht-SDR-Systemen basierend auf dem Ausfalltyp aus, um das System wiederherzustellen. Weitere Informationen zur SDR finden Sie im Symantec Backup Exec Administrator's Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com. Vorbereiten des Systems auf SDR Zum Wiederherstellen des Systems für die Verwendung von SDR führen Sie die folgenden Schritte aus: 1.
ANMERKUNG: Wenn einer der virtuellen Festplatten, die für ein Backup auf Festplatte ausgewählt wurden, ein Laufwerksbuchstabe zugewiesen ist, werden auch der gesamte Inhalt der virtuellen Festplatte für das Backup auf Festplatte als Teil des Backup-Jobs gesichert. Wenn dies nicht erforderlich ist, deaktivieren Sie die Laufwerksbuchstaben. 5. Wenn der DDS vorhanden ist, stellen Sie sicher, dass die Inhalte des DDS ebenfalls ausgewählt sind.
Ausfalltyp Potenziell betroffene Hardware Potenziell betroffene Software ServerLaufwer ksgrupp e Betr DLiebs Appliance syst em Speicherge häuse, Laufwerksgr uppe Server Administrator Backup Exec DSF oder DDS (Ausfall von internem Laufwerk) Speichergehäuse RAID-Gruppen (Externer Laufwerksfehler) Wiederherste llungsverfahr en 1,3,4,7 ohne IDR oder SDR X X Betriebssystem X DL-Appliance X Server Administrator X X X 1,7 2,7 mit IDR oder SDR 3,4,7 ohne IDR oder SDR 4 X Backup Exec 5 X DS
VORSICHT: Ein ausgefallenes Systemlaufwerk muss sofort ausgetauscht werden, um Datenverlust oder einen vollständigen Ausfall des Systems zu vermeiden. Die optionalen Datenlaufwerke in den PowerVault DL2100- und DL2200-Systemen und Speichergehäusen werden von der Datensicherungsanwendung automatisch in RAID 5- oder RAID 6-Laufwerksgruppen konfiguriert, wie im Thema „Laufwerk-Konfigurationseinstellungen“ beschrieben.
Wiederherstellen nach Ausfällen einzelner Laufwerke Nachdem Sie ein ausgefallenes Festplattenlaufwerk innerhalb einer RAID-Gruppe ausgewechselt haben, baut die Anwendung die Laufwerksgruppe automatisch neu auf. Die Daten auf den virtuellen Laufwerken in der Laufwerksgruppe sind für das System weiterhin verfügbar und das System wird ohne Unterbrechung ausgeführt. Das System wird dann bis zum Abschluss des Wiederaufbauvorgangs im „degraded mode“ (eingeschränkter Betriebszustand) betrieben.
• Laufwerke in einem Speichergehäuse: Informationen zum Ersetzen der Laufwerke des Speichergehäuses finden Sie im Hardware Owner’s Manual (Hardware-Benutzerhandbuch) unter support.dell.com/manuals. Wiederherstellen des Systemlaufwerks mit IDR ANMERKUNG: Dieser Abschnitt gilt für DL-Systeme mit Backup Exec-Versionen vor Backup Exec 2012. Bei Backup Exec 2012 und aktueller lesen Sie das Thema „Wiederherstellen des Systemlaufwerks mit SDR“.
VORSICHT: Stellen Sie sicher, dass die Betriebssystem-Laufwerkspartition „C:“ mit dem entsprechenden Laufwerk verknüpft ist. Wenn die Partition „C:“ nicht korrekt ist, entfernen Sie die Laufwerkbuchstabenzuordnung „C:“ mit dem falschen Laufwerk, und weisen Sie sie zur Betriebssystempartition auf Laufwerk 0 zu. Stellen Sie sicher, dass alle übrigen Laufwerkspartitionen korrekt sind bzw. korrigieren Sie diese, bevor Sie den Vorgang fortsetzen. 10.
9. Klicken Sie auf Recover diesen Computer (Diesen Computer wiederherstellen). 10. Wenn Sie dazu aufgefordert, den Speicherort der Backup-Daten auszuwählen, wählen Sie The data is located on devices locally attached to this computer (Die Daten befinden sich auf Geräten, die lokal an diesen Computer angehängt sind). 11. Gehen Sie nach Aufforderung zur Auswahl der Wiederherstellungsdatei zur *.DR-Datei auf dem Wechseldatenträger oder zum entsprechenden Speicherort im Netzwerk gemäß Schritt 3. 12.
Benutzerhandbuch für erweiterbare RAID-Controller (PERC)) unter support.dell.com/manuals auf der Basis des Adaptermodells im PowerVault DL2xxx-System. 3. Im Configuration Utility (Konfigurationsdienstprogramm) des PERC-Adapters stellen Sie sicher, dass das entsprechende virtuelle Laufwerk als Boot-VD ausgewählt ist. Wiederherstellen der Appliance-Systemfestplatte ohne IDR oder SDR Das Betriebssystem ist auf dem System vorinstalliert.
9. Wenn Sie von SBUU dazu aufgefordert werden, den Windows Server Pack-Installationsdatenträger bereitzustellen, legen Sie den Datenträger mit dem Dell Windows Operating Systems install support pack (Unterstützungspaket für Installation von Dell Windows-Betriebssystemen) ein, das Sie von support.dell.com heruntergeladen haben. 10. Klicken Sie auf Finish (Fertig stellen). 11.
ANMERKUNG: Stellen Sie im RAID Configuration Wizard (RAID-Konfigurationsassistenten) sicher, dass Sie die Auswahl von Assign a HS if available (HS zuweisen, falls vorhanden) aufheben, wenn diese standardmäßig aktiviert ist. Lesen Sie jetzt das Thema „Abschluss der Betriebssystem-Neuinstallation“. Abschluss der Betriebssystem-Neuinstallation 1. Nach Abschluss der Windows-Installation ändern Sie auf Aufforderung hin das Kennwort. 2.
Verwenden von Dell PowerVault DL Backup to Disk Appliance Recovery and Update Utility During Disaster Recovery (Wiederherstellungs- und Aktualisierungsprogramms für das Dell PowerVault DL Backup to Disk-System bei der Notfallwiederherstellung) Wenn Sie in einem Notfallwiederherstellungsszenario das Symantec Backup Exec IDR- oder SDR-Verfahren für die Wiederherstellung des Systems verwenden, werden die Anwendungen der DL Backup to Disk Appliance automatisch wiederhergestellt.
Manuelle Installation von Windows Server-Rollen und -Funktionen Das „PowerVault DL Backup to Disk Appliance Recovery and Update Utility“ (PowerVault DL Backup to DiskDienstprogramm zur Wiederherstellung und Aktualisierung) kann zur automatischen Installation aller erforderlichen Windows Server Rollen und Funktionen verwendet werden. Zum manuellen Installieren der erforderlichen Windows Rollen und Funktionen führen Sie die folgenden Schritte aus: 1. Starten Sie den Server-Manager. 2.
5. – Zustand und Diagnose – * HTTP-Protokollierung * Anforderungsüberwachung Sicherheit – * Anfragefilter Leistung – * Statische Inhaltskomprimierung Verwaltungshilfsprogramme * IIS-Verwaltungskonsole * IIS 6-Verwaltungskompatibilität (alle Suboptionen auswählen) Klicken Sie auf Next (Weiter). Das Fenster Confirm Installation Selections (Installationsauswahl bestätigen) wird angezeigt. 6.
4. Wählen Sie Dell OpenManage Server Administrator für die Verwaltung eines eigenständigen Servers, und wählen Sie Install (Installieren) aus. Das Server Administrator-Installationsprogramm führt einen Kompatibilitätstest durch, um sicherzustellen, dass alle Voraussetzungen für eine erfolgreiche Installation erfüllt sind. 5. Wählen Sie Repair oder Modify Installation (Installation reparieren oder modifizieren) aus. Das Installationsprogramm schließt die Reparatur ab.
Reparieren von Symantec Backup Exec Wenn die Installation von Symantec Backup Exec beschädigt ist oder nicht mehr verwendet werden kann und daher repariert werden muss, finden Sie weitere Informationen unter „Repairing Backup Exec“ (Reparieren von Backup Exec) im Symantec Backup Exec Administrator’s Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com.
Tabelle 3.
Methode zum Erstellen des DSF Automatische Laufwerkskonfiguration Neuer DSF-Assistent auf Laufwerksbuchstaben Bestandsaufnahme und Katalogisierung der virtuellen Laufwerke X X Bestandsaufnahme und Katalogisierung eines DSF X X Neuzuordnen von Jobs zum neuen DDS X Löschen von offline geschalteten virtuellen Laufwerken X Wiederherstellen des Betriebssystem und des DSF für IDR Während des Notfalls, wenn der Systemdatenträger und die Datenträger, auf denen der DSF enthalten ist, ausgefallen sind, fü
Nicht-IDR-Wiederherstellung In diesem Abschnitt werden die Wiederherstellungsverfahren beschrieben, die für ein System auszuführen sind, das einen DSF enthält und nicht durch IDR geschützt ist. Wiederherstellen des Betriebssystems für Nicht-IDR Während des Notfalls, wenn der Systemdatenträger ausgefallen ist, die Datenträger, auf denen der DSF enthalten ist, aber unbeschadet geblieben sind, führen Sie die Schritte in der entsprechenden Spalte basierend auf der Methode aus, mit der der DSF erstellt wurde.
Verfahren zum Erstellen des Ordners für den DDS Automatische Laufwerkskonfiguration Neuer DSF-Assistent auf Laufwerksbuchstaben Automatisches Erstellen eines neuen DSF X Manuelles Erstellen eines neuen DSF X Neuzuordnen des Laufwerksbuchstabens zum DSF X Bestandsaufnahme und Katalogisierung der virtuellen Laufwerke X X Wiederherstellen des DSF aus einer Sicherungskopie X X Bestandsaufnahme und Katalogisierung eines DSF X X Systemwiederherstellung für DL-Appliance mit DDS Wenn die Systemkonf
wurde und später auf Backup Exec 2012 aktualisiert wurde, befindet sich der DSF weiterhin auf dem gleichen Laufwerksbuchstaben. Wiederherstellen von DDS Während des Notfalls, wenn der Systemdatenträger und die Datenträger, auf denen der DDS enthalten ist, ausgefallen sind, führen Sie die Schritte in der entsprechenden Spalte basierend auf der Methode aus, die zum Wiederherstellen der DDS verwendet wurde.
Methoden, die zum Erstellen des DeduplizierungLaufwerkspeichers verwendet wurden Automatische Laufwerkskonfiguration Löschen von offline geschalteten virtuellen Laufwerken Manuell über die Backup Exec Console konfiguriert X X Assistent für neuen Deduplizierungsspeicheror dner auf Laufwerksbuchstabe X SDR-Wiederherstellung In diesem Abschnitt werden die Wiederherstellungsverfahren beschrieben, die für ein System auszuführen sind, das einen DDS enthält und durch SDR geschützt ist.
Methoden, die zum Erstellen des DeduplizierungLaufwerkspeichers verwendet wurden Automatische Laufwerkskonfiguration Automatisches Erstellen eines neuen DeduplizierungLaufwerkspeichers Manuell über die Backup Exec-Konsole konfiguriert Assistent für neuen Deduplizierungsspeicheror dner auf Laufwerksbuchstabe X Manuelles Erstellen eines virtuellen Laufwerks für einen neuen DeduplizierungLaufwerkspeicher X Manuelles Konfigurieren des virtuellen Laufwerks für die Deduplizierung X Neuzuordnen des Laufw
Wiederherstellen des Betriebssystems für Nicht-SDR Während des Notfalls, wenn der Systemdatenträger ausgefallen ist, die Datenträger, auf denen der DDS enthalten ist, aber unbeschadet geblieben sind, führen Sie die Schritte in der entsprechenden Spalte basierend auf der Methode aus, mit der der DDS erstellt wurde. Tabelle 11.
Verfahren zum Erstellen des Automatische Ordners für den DDS Laufwerkskonfiguration Manuelles Konfigurieren des virtuellen Laufwerks für die Deduplizierung Manuell über die Backup Exec-Konsole konfiguriert Neuer DSF-Assistent auf Laufwerksbuchstaben X Neuzuordnen von Laufwerksbuchstaben zum DDS X Bestandsaufnahme und Katalogisierung der virtuellen Laufwerke X X X Wiederherstellen des DDS aus einer Sicherungskopie X X X Importieren des DDS vom Laufwerkbuchstaben Bestandsaufnahme und Katalogisie
Neustarten der Backup Exec-Dienste für Backup Exec 2012 Zum Neustarten der Backup Exec-Dienste führen Sie die folgenden Schritte aus: 1. Klicken Sie in der Backup Exec 2012-Konsole auf die Schaltfläche Backup Exec, wählen Sie Configuration and Settings (Konfiguration und Einstellungen) → Backup Exec Services (Backup Exec-Dienste). 2. Wählen Sie Enable deduplication services to be started or stopped (Starten oder Stoppen der Deduplizierungsdienste aktivieren).
Importieren des DDS vom Laufwerkbuchstaben Zum Importieren des DDS von einem Laufwerkbuchstaben führen Sie die folgenden Schritte aus: 1. Starten Sie die Backup Exec-Konsole. 2. Klicken Sie auf die Schaltfläche Backup Exec → Configurations and Settings (Konfigurationen und Einstellungen) → Logon Accounts (Anmeldekonten). 3. Erstellen Sie ein „Backup Exec Logon Account“ mit den gleichen Zugriffsrechten, die ursprünglich zum Erstellen des DDS verwendet wurden. 4.
7. Suchen Sie auf der Ansicht Device (Geräte) in Backup Exec den DSF in der Gerätestruktur unterhalb des Systemnamens aus. 8. Klicken Sie mit der rechten Maustaste auf den DSF und wählen Sie Delete (Löschen). 9. Starten Sie die Backup Exec-Dienste neu. Lesen Sie auch das Thema „Neustarten der Backup Exec-Dienste”. Neuzuordnen von Jobs des gelöschten DSF Alle Jobs, die mit einem gelöschten DSF verknüpft sind, müssen neu zugeordnet werden, da das virtuelle DSF-Laufwerk aus Backup Exec entfernt wurde.
a) Setzen Sie die Disk Configuration Policy (Laufwerkskonfigurationssrichtlinie) auf Automatic With Confirmation (Automatisch mit Konfiguration). Backup Exec erkennt die unkonfigurierten Austauschlaufwerke und fordert Sie dazu auf, die verfügbaren Laufwerke zu konfigurieren. b) Wenn die Meldung „Device Intervention“ (Geräteintervention) nicht automatisch angezeigt wird, starten Sie die Backup Exec-Dienste neu.
1. Klicken Sie auf dem Windows-Desktop auf Start → Administrative Tools (Verwaltung) → Server Manager, und wählen Sie Disk Management (Laufwerksverwaltung) unter Storage (Speicher) aus. 2. Initialisieren Sie das neue virtuelle Laufwerk im Format „GUID Partition Table“ (GPT). 3. Erstellen Sie mithilfe von Disk Management (Laufwerksverwaltung) ein einfaches Volumen auf dem neuen virtuellen Laufwerk.
6. Geben Sie einen Namen für das DDS-Gerät ein. 7. Wählen Sie Import an existing Deduplication Disk Storage Device (Ein vorhandenes DeduplizierungLaufwerkspeichergerät importieren). 8. Geben Sie den Pfad zum Deduplizierung-Laufwerkspeichergerät ein. Beispiel: K:\BackupExecDeduplicationStorageFolder\ 9. Wählen Sie das Anmeldekonto, das Sie in Schritt 3 erstellt haben. 10. Klicken Sie auf Finish (Fertig stellen), um den Importprozess zu beginnen.
1. Gehen Sie zur Registerkarte Settings (Einstellungen) auf der DL Backup to Disk-Systemkonsole, und überprüfen Sie den Disk Configuration State (Status der Laufwerkskonfiguration). 2. Wenn der Disk Configuration State (Status der Laufwerkskonfiguration)auf Standard gesetzt ist, führen Sie die folgenden Schritte aus: a) Setzen Sie die Laufwerkskonfigurationssrichtlinie auf Automatic With Confirmation (Automatisch mit Konfiguration).
Manuelle Konfiguration eines virtuellen DSF-Laufwerks Zum manuellen Konfigurieren eines virtuellen DSF-Laufwerks führen Sie die folgenden Schritte aus: 1. Suchen Sie mithilfe der Backup Exec-Konsole das unkonfigurierte virtuelle DSF-Laufwerk in der Gerätestruktur. 2. Klicken Sie mit der rechten Maustaste auf das virtuelle Laufwerk und wählen Sie die Option Configure (Konfigurieren). 3. Starten Sie die Backup Exec-Dienste neu. Lesen Sie auch das Thema „Neustarten der Backup Exec-Dienste“.
Löschen von offline geschalteten virtuellen Laufwerken Nach der vollständigen Wiederherstellung des Systems enthält die Backup Exec-Gerätestruktur möglicherweise eine oder mehrere offline geschaltete virtuelle Laufwerke, die auf dem System nicht mehr vorhanden sind. Klicken Sie zum Entfernen eines offline geschalteten virtuellen Laufwerks mit der rechten Maustaste auf das Gerät und wählen Sie Delete (Löschen).
6 Lösungsübersicht In diesem Abschnitt sind häufig gestellte Fragen zur Planung der Bereitstellung, Einrichtung, Verwaltung, Speichererweiterung und -migration und Problembehandlung der Dell PowerVault DL Backup to Disk Appliance aufgeführt.
Wie füge ich Bandgeräte zu meiner PowerVault Backup to Disk Appliance hinzu? Informationen zum Hinzufügen von Bandgeräten zu Ihrem System finden Sie in dem Thema „Hinzufügen einer optionalen Bandbibliothek“.
Administrator’s Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com. Wie kann ich die automatischen Warnungen in Symantec Backup Exec konfigurieren? Lesen Sie das Thema „Alerts and Notifications“ (Warnungen und Benachrichtigungen) im Symantec Backup Exec Administrator’s Guide (Administratorhandbuch für Symantec Backup Exec) unter symantec.com. Wie stelle ich mein System unter Verwendung der Notfallwiederherstellung wieder her? Lesen Sie das Thema „Notfallwiederherstellung“.
Wie erfahre ich mehr über die Bereitstellungsfunktionen der Symantec Backup Exec-Software für das Dell PowerVault Backup-System? Lesen Sie das Dokument Symantec Backup Exec Storage Provisioning Wie füge ich zusätzliche Speicherkapazität zu einem PowerVault MDxxxx-Speichergehäuse hinzu? Lesen Sie das Thema „Installing Enclosure Components“ (Installation von Gehäusekomponenten) im Dell PowerVault MDxxxx Storage Wie binde ich neu hinzugefügten Speicher in das PowerVault DL2xxx-System ein? Lesen Sie das Th
Zusätzliche Hinweise 7 In diesem Abschnitt sind die Software- und Hardwaredokumentationen zu Ihrer Referenz aufgeführt. ANMERKUNG: Soweit nicht anderweitig aufgeführt befinden sich alle Dokumentationen unter support.dell.com.
• • • • • Dell PowerVault TL2000/4000 Tape Library User’s Guide (Dell PowerVault TL2000/4000 - BandbibliothekBenutzerhandbuch) enthält Informationen zur optionalen TL2000/4000-Bandbibliothek. Dell PowerVault ML6000 Tape Library User's Guide (Dell PowerVault ML6000 - Band-Library-Benutzerhandbuch) enthält Informationen zur optionalen ML6000-Bandbibliothek. Dell PowerVault 122T Autoloader User's Guide (Dell PowerVault 122T - Autoloader-Benutzerhandbuch) enthält Informationen zum optionalen 122T Autoloader.
• Dell OpenManage Management Station, die unter support.dell.com/support/downloads heruntergeladen werden kann, enthält IT Assistant, das BMC-Verwaltungsdienstprogramm, die Dell Remote Access Controller-Konsole und das Microsoft Active Directory Snap-in Utility. • Dell Systems Management Tools and Documentation-DVD, die mit dem System ausgeliefert wird (ein Image des Datenträgers kann unter support.dell.
Wie Sie Hilfe bekommen 8 Kontaktaufnahme mit Dell ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit. Da die Verfügbarkeit dieser Optionen je nach Land und Produkt variiert, stehen einige Services in Ihrer Region möglicherweise nicht zur Verfügung.