Dell PowerVault DL2300 オーナーズマニュアル 規制モデル: E14S Series 規制タイプ: E14S001
メモ、注意、警告 メモ: コンピュータを使いやすくするための重要な情報を説明しています。 注意: ハードウェアの損傷やデータの損失の可能性を示し、その問題を回避するための方法を説明してい ます。 警告: 物的損害、けが、または死亡の原因となる可能性があることを示しています。 © 2012 Dell Inc. 本書に使用されている商標:Dell™、Dell のロゴ、Dell Boomi™、Dell Precision™、OptiPlex™、Latitude™、PowerEdge™、PowerVault™、 PowerConnect™、OpenManage™、EqualLogic™、Compellent™、KACE™、FlexAddress™、Force10™ および Vostro™ は Dell Inc. の商標で す。Intel®、Pentium®、Xeon®、Core® および Celeron® は米国およびその他の国における Intel Corporation の登録商標です。 AMD® は Advanced Micro Devices, Inc.
目次 メモ、注意、警告.......................................................................................................................2 章 1: システムについて.............................................................................................................9 前面パネルの機能とインジケータ.....................................................................................................................9 診断インジケータ..................................................................................................................
前面ベゼルの取り外し.................................................................................................................................33 前面ベゼルの取り付け.................................................................................................................................34 システムカバーの開閉........................................................................................................................................34 システムカバーの取り外し...................................................................
拡張カードを拡張カードライザー 1 に取り付ける方法.........................................................................57 拡張カードライザーの取り外し.................................................................................................................58 拡張カードライザーの取り付け.................................................................................................................61 SD VFlash カード.........................................................................................................................................
システム基板の取り付け.............................................................................................................................89 章 4: システムのトラブルシューティング.......................................................................91 作業にあたっての注意........................................................................................................................................91 システム起動エラーのトラブルシューティング...........................................................................................
アラートメッセージ..........................................................................................................................................127 章 9: 困ったときは..................................................................................................................129 デルへのお問い合わせ......................................................................................................................................
1 システムについて 前面パネルの機能とインジケータ 図 1.
項目 インジケータ、ボタン、 またはコネクタ アイコン 説明 このボタンは、認定を受けたサポート担当者によっ て指示された場合、または OS のマニュアルで指示さ れている場合にのみ使用してください。 5 ハードドライブ ホットスワップ対応の 3.5 インチハードドライブを 12 台まで。 6 ビデオコネクタ VGA ディスプレイをシステムに接続するときに使用 します。 7 USB コネクタ USB デバイスをシステムに接続するときに使用しま す。ポートは USB 2.
ハードドライブインジケータ 状態 対応処置 ハードドライブに エラーが発生する と、インジケータ が黄色に点滅しま す。 エラーが発生しているハードドライブを特定するには、システ ムイベントログを参照してください。適切なオンライン Diagnostics(診断)テストを実行します。システムを再起動 し、内蔵された Diagnostics(診断)(ePSA)を実行します。 ハードドライブが RAID アレイとして構成されている場合は、 システムを再起動し、ホストアダプタ設定ユーティリティプロ グラムを起動します。 電気インジケータ 状態 対応処置 システムに電気的 なエラー(電圧の 異常、電源ユニッ トや電圧レギュレ ータの障害など) が発生すると、こ のインジケータが 黄色に点滅しま す。 特定の問題については、システムイベントログまたはシステム メッセージを参照してください。電源ユニットが原因である 場合は、電源ユニットの LED を確認します。電源ユニットをい ったん取り外して取り付けなおします。問題が解決しない場 合は、「困ったときは」を参照してください。 温度インジケータ 状態
PCIe インジケータ 状態 対応処置 PCIe カードにエラ ーが発生すると、 このインジケータ が黄色に点滅しま す。 システムを再起動します。PCIe カードに必要なドライバをす べてアップデートします。カードを取り付けなおします。問 題が解決しない場合は、 「困ったときは」を参照してください。 ハードディスクドライブインジケータのパターン 図 2. ハードディスクドライブインジケータ 1. ハードディスクドライブアクティビティインジケータ(緑色) 2.
ドライブステータ スインジケータの パターン(RAID の み) 状態 緑色にゆっくり点 滅 ドライブの再構築中 緑色の点灯 ドライブがオンライン 緑色に 3 秒間点滅、 再構築中止 橙色に 3 秒間点滅、 6 秒間消灯 背面パネルの機能とインジケータ 図 3.
項目 インジケータ、ボタン、 アイコン またはコネクタ 説明 5 シリアルコネクタ シリアルデバイスをシステムに接続するときに使用 します。 6 ビデオコネクタ VGA ディスプレイをシステムに接続するときに使用 します。 7 USB コネクタ(2) USB デバイスをシステムに接続するときに使用しま す。ポートは USB 2.0 対応です。 8 イーサネットコネクタ (4) 内蔵 10/100/1000 Mbps NIC コネクタ 4 個 または 以下を含む内部コネクタ 4 個: • • 10/100/1000 Mbps NIC コネクタ 2 個 100 Mbps/1 Gbps/10 Gbps SFP+/10 GbE T コネク タ2個 9 PCIe 拡張カードスロット フルハイト(3) フルハイト PCI Express 拡張カードを 3 枚まで取り付 けることができます。 10 電源ユニット(PSU1) 750 W AC 11 電源ユニット(PSU2) 750 W AC 12 ハードドライブ(2)(背 面) ホットスワップ対応 2.
インジケータ インジケータコード リンクインジケー タが橙色 NIC は、最大ポート速度未満で有効なネットワークに接続されています。 アクティビティイ ンジケータが緑色 に点滅 ネットワークデータの送信中または受信中です。 電源インジケータコード 各 AC 電源装置には光源付きの透明なハンドル、各 DC 電源装置(使用可能な場合)には LED があり、これら は電源が供給されているかどうか、または電源障害が発生したかどうかを示すインジケータとしての役目を 果たします。 図 5. AC 電源装置ステータスインジケータ 1. AC 電源装置ステータスインジケータ / ハンドル 図 6. DC 電源装置ステータスインジケータ 1.
電源インジケータ のパターン 状態 消灯 電源が接続されていません。 緑色 緑色に点灯するハンドル / LED インジケータは、有効な電源が電源装置に接続され、電 源装置が稼働していることを示します。 橙色に点滅 電源装置に問題があることを示します。 注意: 電源装置の不一致を修正するときは、インジケータが点滅している電源装置 のみを交換してください。もう一方の電源装置を交換して一致するペアを作ろう とすると、エラー状態および予期しないシステムシャットダウンの原因となる場 合があります。高出力設定から低出力設定(またはその逆)への変更には、シス テムの電源を切る必要があります。 注意: AC 電源装置は 220 V および 110 V 入力電圧の両方をサポートします。同一の 電源装置 2 台が異なる入力電圧を受け取ると、これらの電源装置は異なるワット 数を出力する可能性があり、不一致を誘発します。 注意: 2 台の電源装置を使用する場合は、両装置のタイプと最大出力電力が同じで ある必要があります。 注意: AC および DC 電源装置の混在はサポートされておらず、不一致を誘発しま す。 緑色の
セットアップユーティリティとブートマネ ージャの使い方 2 注意: BIOS の変更は、サポート電話で Dell 認定を受けたデルの技術者との通話中にのみ行うことをお勧 めします。 メモ: ソリューションの検証は工場出荷のハードウェア構成を使用して行われています。 セットアップユーティリティでは、システムハードウェアの管理と BIOS レベルオプションの指定を行うこと ができます。 起動時に以下のキー操作を行うと、システム機能にアクセスできます。 キーストローク 説明 セットアップユーティリティが起動します。 システムサービスが起動し、Dell Lifecycle Controller 2(LC2)が開きます。Dell LC2 は、 GUI を使用した OS の導入、ハードウェア診断、プラットフォームアップデート、およ びプラットフォーム設定などのシステム管理機能をサポートします。正確な LC2 の機 能セットは、ご購入の iDRAC ライセンスによって異なります。詳細については、Dell LC2 のマニュアルを参照してください。 BIOS ブートマネージャ
セットアップユーティリティの起動 1. システムの電源を入れるか、再起動します。 2.
メニュー項目 説明 iDRAC Settings (iDRAC 設定) このオプションは、iDRAC 設定の表示と設定を行うために使用します。 Device Settings(デバ このオプションは、デバイス設定の表示と設定を行うために使用します。 イス設定) System BIOS(システム BIOS)画面 メモ: セットアップユーティリティのオプションはシステム構成に応じて変わります。 メモ: セットアップユーティリティのデフォルト設定を以下の項の該当する各オプションの下に示しま す。 メニュー項目 説明 System Information (システム情報) システムモデル名、BIOS バージョン、サービスタグなど、システムに関する情報が表 示されます。 Memory Settings(メ 取り付けられているメモリに関連する情報とオプションが表示されます。 モリ設定) Processor Settings (プロセッサ設 定) 速度、キャッシュサイズなど、プロセッサに関する情報とオプションが表示されます。 Boot Settings(起動 設定) 起動モード(BIOS または U
システム情報画面 メニュー項目 説明 System Model Name (システムモデル 名) システムモデル名が表示されます。 System BIOS Version システムにインストールされている BIOS バージョンが表示されます。 (システム BIOS バ ージョン) System Service Tag (システムのサー ビスタグ) システムのサービスタグが表示されます。 System Manufacturer システム製造元の名前が表示されます。 (システム製造 元) System Manufacturer システム製造元の連絡先情報が表示されます。 Contact Information (システム製造元 の連絡先情報) メモリ設定画面 メニュー項目 説明 System Memory Size (システムメモリ のサイズ) システムに取り付けられているメモリの容量が表示されます。 System Memory Type システムに取り付けられているメモリのタイプが表示されます。 (システムメモリ のタイプ) システムメモリの速度が表示されます。 System Memory
メニュー項目 説明 Memory Operating Mode(メモリ動作 モード) メモリの動作モードを指定します。お使いのシステムのメモリ構成に応じて使用可能 なオプションは、Optimizer Mode(オプティマイザモード)、Advanced ECC Mode(ア ドバンス ECC モード)、Mirror Mode(ミラーモード)、Spare Mode(スペアモー ド)、および Spare with Advanced ECC Mode(スペア + アドバンス ECC モード)です。 デフォルトでは、Memory Operating Mode(メモリ動作モード)オプションは Optimizer Mode(オプティマイザモード)に設定されています。 メモ: メモリ動作モードには、メモリ設定に基づいて、異なるデフォルトおよび利 用可能オプションがあります。 Node Interleaving(ノ 対称的なメモリ構成の場合、このフィールドが Enabled(有効)に設定されていると、 ードのインタリー メモリのインタリービングがサポートされます。このフィールドが Disabled(無効) ビング) に
メニュー項目 説明 ッシュラインのプ リフェッチ) す。ランダムなメモリアクセスの頻度が高いアプリケーションを使用する場合は、こ のオプションを無効にします。 Hardware Prefetcher ハードウェアのプリフェッチャを有効または無効化することができます。デフォルト (ハードウェアの では、Hardware Prefetcher(ハードウェアのプリフェッチャ)オプションは Enabled(有 プリフェッチャ) 効)に設定されています。 データキャッシュユニットストリーマのプリフェッチャを有効または無効化すること DCU Streamer Prefetcher(DCU スト ができます。デフォルトでは、DCU Streamer Prefetcher(DCU ストリーマのプリフェッ リーマのプリフェ チャ)オプションは Enabled(有効)に設定されています。 ッチャ) DCU IP Prefetcher (DCU IP のプリフ ェッチャ) データキャッシュユニット IP のプリフェッチャを有効または無効化することができ ます。デフォルトでは、DCU IP Prefetcher(DCU I
メニュー項目 説明 Number of Cores(コ プロセッサごとのコア数を表示します。 ア数) Boot Settings(起動設定)画面 メニュー項目 説明 Boot Mode(起動モ ード) システムの起動モードを設定できます。 注意: OS インストール時の起動モードが異なる場合、起動モードを切り替えると システムが起動しなくなることがあります。 デフォルトでは、Boot Mode(起動モード)オプションは BIOS に設定されています。 Boot Sequence Retry 起動順序の再試行機能の有効 / 無効を切り替えることができます。このフィールドが (起動順序再試 有効に設定されていて、システムが起動に失敗した場合、システムは 30 秒後に起動を 行) 再試行します。デフォルトでは、Boot Sequence Retry(起動順序試行)オプションは Disabled(無効)に設定されています。 BIOS Boot Settings (BIOS 起動設定) BIOS Boot(BIOS 起動)オプションの有効 / 無効を切り替えることができます。 One-Time Boo
メニュー項目 説明 SD カードの冗長 性) ピーされます。デフォルトでは、Internal SD Card Redundancy(内蔵 SD カードの冗長 性)オプションは Mirror(ミラー)に設定されています。 メモ: このオプションは、システム基板に IDSDM が取り付けられている場合にの み表示されます。 Integrated Network 内蔵ネットワークカード 1 の有効 / 無効を切り替えることができます。デフォルトで Card 1(内蔵ネット は、Integrated Network Card 1(内蔵ネットワークカード 1)オプションは Enabled(有 ワークカード 1) 効)に設定されています。 OS Watchdog Timer (OS ウォッチドッ グタイマー) OS ウォッチドッグタイマーの有効 / 無効を切り替えることができます。このフィー ルドが有効の場合、OS がタイマーを初期化し、OS ウォッチドッグタイマーが OS のリ カバリを支援します。デフォルトでは、OS Watchdog Timer(OS ウォッチドッグタイマ ー)オプションは Disable
メニュー項目 説明 External Serial 外付けシリアルコネクタをシリアルデバイス 1、シリアルデバイス 2、またはリモート Connector(外付けシ アクセスデバイスに関連付けることができます。デフォルトでは、External Serial リアルコネクタ) Connector(外付けシリアルコネクタ)オプションは Serial Device1(シリアルデバイ ス 1)に設定されています。 メモ: SOL にはシリアルデバイス 2 のみを使用できます。SOL でコンソールのリダ イレクトを使用するには、コンソールのリダイレクトとシリアルデバイスに同じ ポートアドレスを設定します。 Failsafe Baud Rate (フェイルセーフ ボーレート) コンソールのリダイレクトに使用されているフェイルセーフボーレートが表示されま す。BIOS は自動的にボーレートの決定を試みます。このフェイルセーフボーレート は、その試みが失敗した場合にのみ使用されます。また、値は変更しないでください。 デフォルトでは、Failsafe Baud Rate(フェイルセーフボーレート)オプションは 11520
メニュー項目 説明 C1E アイドル時にプロセッサが最小パフォーマンス状態に切り替わるかどうかを設定でき ます。デフォルトでは、C1E オプションは Enabled(有効)に設定されています。 C States(C ステー ト) プロセッサが利用可能なすべての電源状態で動作するかどうかを設定できます。デフ ォルトでは、C States(C ステート)オプションは Enabled(有効)に設定されていま す。 Monitor/Mwait プロセッサ内の Monitor/Mwait 命令を有効にすることができます。デフォルトでは、 Monitor/Mwait オプションは Custom(カスタム)を除くすべてのシステムプロファイル に対して Enabled(有効)に設定されています。 メモ: このオプションは、Custom(カスタム)モードで C States(C ステート)オ プションが無効に設定されている場合に限り、無効に設定できます。 メモ: Custom(カスタム)モードで C States(C ステート)が有効に設定されてい ると、Monitor/Mwait 設定を変更してもシステムの能力
メニュー項目 説明 の有効化)フィールド、および Intel TXT フィールドは、TPM Status(TPM ステータス) フィールドが On with Pre-boot Measurements(起動前測定ありでオン)または On without Pre-boot Measurements(起動前測定なしでオン)のいずれかに設定されている場合に 限り、変更できます。 TPM Activation(TPM TPM の動作状態を変更することができます。デフォルトでは、TPM Activation(TPM の の有効化) 有効化)オプションは No Change(変更なし)に設定されています。 TPM Status(TPM ス TPM の状態が表示されます。 テータス) TPM Clear(TPM の クリア) 注意: TPM をクリアすると、TPM 内のすべてのキーが失われます。TPM キーが失 われると、OS の起動に影響するおそれがあります。 TPM の全コンテンツをクリアすることができます。デフォルトでは、TPM Clear(TPM のクリア)オプションは No(なし)に設定されています。 I
その他の設定 メニュー項目 説明 System Time(システ システムの時刻を設定することができます。 ム時刻) System Date(システ システムの日付を設定することができます。 ム日付) Asset Tag Asset Tag が表示されます。Asset Tag はセキュリティと追跡のために変更することが できます。 Keyboard NumLock (キーボードの NumLock) NumLock が有効または無効のどちらの状態でシステムが起動するかを設定することが できます。デフォルトでは、Keyboard NumLock(キーボードの NumLock)は On(オ ン)に設定されています。 メモ: このフィールドは 84 キーのキーボードには適用されません。 Report Keyboard Errors(キーボード エラーの報告) システム起動時にキーボード関連のエラーメッセージが報告されるかどうかを設定す ることができます。デフォルトでは、Report Keyboard Errors(キーボードエラーの報 告)フィールドは Report(報告する)に設定されています。 F
システムパスワードおよび / またはセットアップパスワードの割り当て メモ: パスワードジャンパによって、システムパスワードとセットアップパスワードの機能の有効 / 無効 を切り替えることができます。パスワードジャンパの設定については、 「システム基板のジャンパ設定」 を参照してください。 パスワードジャンパの設定が有効で Password Status(パスワードステータス)が Unlocked(ロック解除)の 場合に限り、新しい System Password(システムパスワード)や Setup Password(セットアップパスワード) の設定、または既存の System Password(システムパスワード)や Setup Password(セットアップパスワー ド)の変更が可能です。Password Status(パスワードステータス)が Locked(ロック)に設定されている場 合、System Password(システムパスワード)や Setup Password(セットアップパスワード)の変更はできま せん。 パスワードジャンパの設定を無効にすると、既存の System Password(シス
既存のシステムパスワードおよび / またはセットアップパスワードの削除または 変更 既存のシステムパスワードおよび / またはセットアップパスワードの削除または変更を試みる前に、パスワ ードジャンパが有効に設定され、Password Status(パスワードステータス)が Unlocked(ロック解除)にな っていることを確認します。Password Status(パスワードステータス)が Locked(ロック)の場合、既存の システムパスワードやセットアップパスワードを削除または変更することはできません。 既存のシステムパスワードおよび / またはセットアップパスワードを削除または変更する手順は、次のとお りです。 1. セットアップユーティリティを起動するには、電源投入または再起動の直後に を押します。 2. System Setup Main Menu(セットアップユーティリティのメインメニュー)で System BIOS(システム BIOS)を選択し、 を押します。 System BIOS(システム BIOS)画面が表示されます。 3.
メモ: 不正な変更からシステムを保護するために、System Password(システムパスワード)と Setup Password(セットアップパスワード)オプションを Password Status(パスワードステータス)オプショ ンと併用することができます。 セットアップパスワード使用中の操作 Setup Password(セットアップパスワード)が Enabled(有効)に設定されている場合は、ほとんどのシステ ムセットアップオプションを変更する前に、正しいセットアップパスワードを入力します。 3 回目までに正しいパスワードを入力しないと、次のメッセージが表示されます。 Incorrect Password! Number of unsuccessful password attempts: System Halted! Must power down.
システム部品の取り付け 3 メモ: ソリューションの検証は工場出荷のハードウェア構成を使用して行われています。 奨励するツール 本項の手順を実行するには、以下のアイテムが必要です。 • システムキーロックのキー • #2 プラスドライバ • T8 および T15 のトルクスドライバ • アースされた静電気防止用リストバンド DC 電源ユニット(利用可能な場合)のケーブルをまとめるのに、以下のツールが必要です。 • AMP 90871-1 圧着ハンドツールまたは同等のツール • サイズ 10 の AWG ソリッドワイヤまたは絶縁された銅製のより線から絶縁材を除去できる絶縁電線プ ライヤ メモ: アルファワイヤパーツナンバー 3080 または同等のもの(65/30 より線)を使用します。 前面ベゼル(オプション) 前面ベゼルの取り外し 1. ベゼルの左端のキーロックを解除します。 2. キーロックの横にあるリリースラッチを押し上げます。 3. ベゼルの左端を前面パネルと反対の方向へ動かします。 4.
図 7. 前面ベゼルの取り外しと取り付け 1. 2. 3. 4. リリースラッチ キーロック 前面ベゼル ロックフック 前面ベゼルの取り付け 1. ベゼルの右端をシャーシに取り付けます。 2. ベゼルのもう一方をシステムにはめ込みます。 3.
3. システム上部のラッチを上げ、カバーを後方にスライドさせます。 4. カバーの両側をつかみ、カバーをシステムから慎重に持ち上げて、取り外します。 図 8. システムカバーの取り外しと取り付け 1. システムカバー 2. ラッチ 3. ラッチリリースロック システムカバーを閉じる 1. カバーのラッチを上げます。 2. 3. カバーをシャーシの上に配置し、シャーシのフックを避けてシステムシャーシと平らになるように、カ バーをわずかに後方にずらします。 ラッチを押し下げてカバーを閉じ位置に動かします。 4. ラッチリリースロックを時計方向に回してカバーを固定します。 5.
図 9. システムの内部 1. 2. 3. 4. 5. 6. 7. 8. 冷却ファンアセンブリ ケーブル固定ブラケット 冷却用エアフローカバー ハードドライブバックプレーン(背面) vFlash メディアスロット ハードドライブ(背面)(2) 拡張カードライザー 3 ネットワークドーターカード 9. 10. 11. 12. 13. 14.
1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. フルレングス PCIe カードが取り付けられている場合は、取り外します。 4. タッチポイントを持ち、冷却用エアフローカバーを持ち上げてシステムから取り出します。 図 10. 冷却用エアフローカバーの取り外しと取り付け 1. 冷却用エアフローカバー 2.
システムにはメモリソケットが 24 個あり、12 個 ずつの 2 セット(各プロセッサに 1 セット)に分かれていま す。ソケット 12 個の各セットは、4 つのチャネルで構成されています。どのチャネルも、最初のソケットの リリースレバーは白、2 番目のソケットのレバーは黒、3 番目のソケットのレバーは緑に色分けされていま す。 メモ: ソケット A1 ~ A12 の DIMM はプロセッサ 1 に、ソケット B1 ~ B12 の DIMM はプロセッサ 2 に割り 当てられています。 図 11.
メモ: x4 と x8 DRAM ベースの DIMM が併用でき、RAS 特性がサポートされます。ただし、特定の RAS 特 性に関するすべてのガイドラインに準拠している必要があります。x4 DRAM ベースの DIMM は、メモリ 最適化(独立チャネル)モードで SDDC(Single Device Data Correction)を維持します。x8 DRAM ベース の DIMM が SDDC を獲得するには、アドバンス ECC モードを必要とします。 以下の各項では、各モードの詳しいメモリ装着ガイドラインを説明します。 Advanced ECC (Lockstep)(アドバンス ECC(ロックステップ)) メモ: アドバンス ECC は Value システム構成でのみサポートされています。 Advanced ECC(アドバンス ECC)モードでは、SDDC が x4 DRAM ベースの DIMM から x4 と x8 の両方の DRAM に拡張されます。これにより、通常動作中のシングル DRAM チップ障害から保護されます。 メモ: メモリモジュールは、サイズ、速度、テクノロジが同一のものを取り付けて
メモ: 下の表で 2R はデュアルランク RDIMM を表します。 表 1.
図 12. メモリモジュールの取り外しと取り付け 1. メモリモジュール 2. メモリモジュールソケットのイジェクタ(2) 3. 位置合わせキー 6. 適切なシステム冷却を確実にするため、空のメモリモジュールソケットにはメモリモジュールダミーを 取り付けてください。 7. 冷却用エアフローカバーを取り付けます。 8. システムカバーを閉じます。 9.
5. メモリモジュールソケットのイジェクタを押し下げて外し、メモリモジュールをソケットに挿入できる ようにします。メモリモジュールダミーがソケットに取り付けられている場合は、ダミーを取り外しま す。 メモ: 取り外したメモリモジュールダミーは、将来使用するために保管しておきます。 注意: メモリモジュールはカードの端のみを持ちます。端以外の部分には絶対に触れないでくださ い。 6. メモリモジュールソケットの位置合わせキーにメモリモジュールのエッジコネクタを合わせ、ソケット にメモリモジュールを差し込みます。 メモ: メモリモジュールソケットには位置合わせキーがあり、メモリモジュールは一方向にしか取り 付けられません。 7. ソケットレバーがロック位置に固定されるまで、メモリモジュールを両手の親指で押し下げます。 メモリモジュールがソケットに適切に装着されると、メモリモジュールソケットのレバーがメモリモジ ュールが装着されている別のソケットのレバーと同じ位置に揃います。 8. 手順 4~7 を繰り返して、残りのメモリモジュールを取り付けます。 9.
ハードドライブスロットから外れるまで、ハードドライブダミーを引き出します。 図 13. 2.5 インチハードドライブダミー(背面)の取り外しと取り付け 1. ハードドライブダミー(背面) 2.5 インチハードドライブダミー(背面)の取り付け メモ: この手順は、シャーシ背面の 2.5 インチハードドライブ 2 台にのみ適用されます。 カチッと固定されるまで、ハードドライブダミーをハードドライブスロットに挿入します。 3.5 インチハードドライブダミーの取り外し 注意: システムの正常な冷却状態を維持するために、空のハードドライブスロットすべてにドライブダミ ーを取り付ける必要があります。 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. ハードドライブダミーの前面を持ち、リリースボタンを押しながら、ハードドライブスロットから外れ るまでダミーを手前に引き出します。 図 14. 3.5 インチハードドライブダミーの取り外しと取り付け 1. ハードドライブダミー 2.
3.5 インチハードドライブダミーの取り付け 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. リリースボタンがカチッと固定されるまで、ハードドライブダミーをハードドライブスロットに挿入し ます。 3. 前面ベゼルを取り外した場合は、取り付けます。 ホットスワップ対応ハードディスクドライブの取り外し 注意: データの損失を防ぐために、お使いのオペレーティングシステムがホットスワップによるドライブ の取り付けに対応していることを確認してください。お使いのオペレーティングシステムのマニュア ルを参照してください。 1.
ホットスワップ対応ハードディスクドライブの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 注意: ハードディスクドライブバックプレーンとの使用がテストおよび承認済みのハードディスクドラ イブのみを使用してください。 注意: 同じ RAID ボリューム内での SAS および SATA ハードディスクドライブの組み合わせはサポートさ れていません。 注意: ハードディスクドライブの取り付け時は、隣接するドライブが完全に取り付けられている事を確認 してください。完全に取り付けられていないキャリアの隣にハードディスクキャリアを挿入してハン ドルをロックしようとすると、完全に取り付けられていないキャリアのシールドバネが損傷し、使用で きな
図 16. ハードドライブキャリアへのハードドライブの取り付けと取り外し 1. ハードディスクドライブキャリア 2. ハードディスクドライブ 3. ネジ(4) ハードディスクドライブキャリアへのハードディスクドライブの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. ハードディスクドライブのコネクタ側をキャリア後部に向けて、ドライブをハードディスクドライブキ ャリアに挿入します。 2. ハードディスクドライブのネジ穴をハードディスクドライブキャリアの後部の穴に合わせます。 正しく揃うと、ハードディスクドライブの背面とハードディスクドライブキャリアの背面が平らに揃い ます。 3.
冷却ファンの取り外し 警告: システムの電源が入っている状態でシステムカバーを開いたり取り外したりすると、感電するおそ れがあります。冷却ファンの取り外しや取り付けの際には、細心の注意を払ってください。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 注意: 冷却ファンはホットスワップ対応です。システムの電源がオンの場合に適切な冷却効果を維持す るため、ファンの交換は 1 台ずつ行ってください。 注意: カバーを取り外した状態で 5 分間以上システムを使用しないでください。 メモ: 各ファンの取り外し手順は同じです。 1. システムカバーを開きます。 2.
冷却ファンの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムカバーを開きます。 2. 冷却ファンの底部にあるプラグをシステム基板のコネクタに合わせます。 3. タブが所定の位置にロックされるまで、冷却ファンを固定スロットに挿入します。 4.
1. 2. 3. 4. 5. 冷却ファンアセンブリ 冷却ファン(6) 青色のリリースレバー(2) ガイドピン(2) 冷却ファンコネクタ(6) 冷却ファンアセンブリの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 注意: 冷却ファンアセンブリを取り付ける前に、ケーブルが正しく接続され、ケーブル保持ブラケットに よって支えられていることを確認します。ケーブルが正しく接続されていないと、損傷するおそれがあ ります。 1. 冷却ファンアセンブリスロットをシャーシのガイドピンに合わせます。 2. 冷却ファンアセンブリをシャーシに挿入します。 3.
5. USB コネクタに USB メモリキーを挿入します。 6. システムカバーを閉じます。 7. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 8. セットアップユーティリティを起動し、USB キーがシステムによって検知されていることを確認します。 図 19. 内蔵 USB キーの交換 1. USB メモリキーコネクタ 2.
図 20. PCIe カードホルダの取り外しと取り付け 1. PCIe カードホルダ 2. リリースタブ PCIe カードホルダの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 注意: PCIe カードホルダが取り付けられていない状態でシステムを使用しないでください。PCIe カード ホルダは、システムの正常な冷却状態を維持するために必要です。 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを開きます。 3. PCIe カードホルダをシャーシのプロジェクションに合わせ、しっかりと装着されるまで押し下げます。 4.
1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. PCIe カードホルダラッチを開くには、タブを押します。 4. PCIe カードホルダラッチを閉じるには、固定されるまでラッチを時計方向に回します。 メモ: フルレングス PCIe カードを取り付ける前に、PCIe カードホルダラッチを閉じる必要がありま す。フルレングス PCIe カードを取り付ける場合は、PCIe カードホルダラッチを開きます。フルレン グス PCIe カードを取り外す前に、PCIe カードホルダラッチを閉じる必要があります。 図 21. PCIe カードホルダラッチの開閉 1. PCIe カードホルダ 2. タブ 3. PCIe カードホルダラッチ 5. システムカバーを閉じます。 6.
図 22. ケーブル保持ブラケットの取り外しと取り付け 1. 位置合わせピン(2) 2. タブ 3. ケーブル保持ブラケット ケーブル保持ブラケットの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを開きます。 3. 位置合わせピンをガイドとして使用しながら、タブが所定の位置に固定されるまで、ケーブル保持ブラ ケットをシャーシ側面に沿ってスライドさせます。 4. 配線するすべてのケーブルをケーブル保持ブラケットに入れます。 5. 冷却用エアフローカバーを取り付けます。 6.
表 2.
7. メモ: システムが FCC(米国連邦通信委員会)の認証を維持するには、空いている拡張スロットにダ ミーブラケットを取り付ける必要があります。また、ダミーブラケットはゴミやホコリがシステム に入るのを防ぎ、システム内部の適正な冷却と通気を助ける働きがあります。 システムカバーを閉じます。 8. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 図 23. 拡張カードの取り外しと取り付け 1. 2. 3. 4. 5.
手順については、カードに付属のマニュアルを参照してください。 2. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 3. システムカバーを開きます。 4. 拡張カードラッチを引き出し、フィラーブラケットを取り外します。 5. 拡張カードの両端を持ち、カードのコネクタをライザーの拡張カードコネクタに合わせます。 6. カードエッジコネクタを拡張カードコネクタにしっかりと挿入し、カードを固定します。 7. 拡張カードラッチを取り付けます。 8. フルレングスカードを取り付けるには、冷却用エアフローカバーに付いているサポートを使用します。 9. 拡張カードにケーブルがある場合は、ケーブルを拡張カードに接続します。 メモ: GPU カードをライザー 2 またはライザー 3(デフォルト)に取り付ける場合は、GPU カードの 電源ケーブルをライザーの電源コネクタに接続します。 10. システムカバーを閉じます。 11. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 12.
図 24. 拡張カードライザー 1 の取り外しと取り付け 1. 2. 3. 4. 拡張カードライザー 1 のケージ 拡張カードコネクタ 拡張カード 拡張カードラッチ(2) 拡張カードを拡張カードライザー 1 に取り付ける方法 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: 拡張カードライザー 1 は、両方のプロセッサが取り付けられている場合にのみ使用できます。 1. 拡張カードをパッケージから取り出し、取り付けの準備をします。 手順については、カードに付属のマニュアルを参照してください。 2. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 3.
9. 拡張カードラッチを閉じます。 10. 拡張カードにケーブルがある場合は、ケーブルを拡張カードに接続します。 11. 拡張カードライザーを取り付けます。 12. システムカバーを閉じます。 13. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 14. カードのマニュアルに従って、必要なすべてのデバイスドライバをインストールします。 拡張カードライザーの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: 拡張カードライザー 1 は、両方のプロセッサが取り付けられている場合にのみ使用できます。 1.
図 26. 拡張カードライザー 1 のコネクタの識別 1. 拡張カードスロット 1 2. 拡張カードスロット 2 3. 拡張カードスロット 3 図 27. 拡張カードライザー 2 の取り外しと取り付け 1. 2. 3. 4. 5.
図 28. 拡張カードライザー 2 のコネクタの識別 1. 2. 3. 4. シャーシイントルージョンスイッチ 拡張カードスロット 4 拡張カードスロット 5 電源コネクタ(GPU カード用) 図 29. 拡張カードライザー 3 の取り外しと取り付け 1. 2. 3. 4. 5.
図 30. 拡張カードライザー 3 のコネクタの識別 1. 拡張カードスロット 6 2. 拡張カードスロット 7 3. 電源コネクタ(GPU カード用) 4. 拡張カードがある場合は、ライザーの拡張カードを取り外すか、または取り付けます。 5. 拡張カードライザーを取り付けます。 6. システムカバーを閉じます。 7. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 拡張カードライザーの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 必要に応じて、取り外した拡張カードを拡張カードライザーに取り付けます。 2.
図 31. SD vFlash カードの取り外しと取り付け 1. SD VFlash カード 2. SD vFlash カードスロット 3. SD vFlash メディアカードを取り付けるには、ラベル側を上に向けて、SD カードの接続ピン側をモジュー ルのカードスロットに挿入します。 メモ: スロットは正しい方向にしかカードを挿入できないように設計されています。 4. カードを押し込んでスロットにロックします。 vFlash メディアユニットの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2.
図 32. vFlash メディアユニットの取り外しと取り付け 1. 2. 3. 4. ケーブル ネジ vFlash メディアユニット 突起 vFlash メディアユニットの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを開きます。 3. vFlash メディアユニットをシャーシの背面方向に挿入します。 4. ケーブルを vFlash メディアユニットに接続します。 5. vFlash メディアユニットをシャーシに固定するネジを取り付けます。 6.
内蔵デュアル SD モジュール メモ: セットアップユーティリティの Integrated Devices(内蔵デバイス)画面で Redundancy(冗長性) オプションが Mirror Mode(ミラーモード)に設定されている場合、1 枚の SD カードから別の SD カード に情報が複製されます。 内蔵デュアル SD モジュールの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3.
図 33. 内蔵デュアル SD モジュールの取り外しと取り付け 1. 2. 3. 4. 5. 青色のプルタブ SD カード 1 SD カード 2 デュアル SD モジュール システム基板上のコネクタ 内蔵デュアル SD モジュールの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. 4. ライザーに取り付けられているカードがあればそれも含めて、拡張カードライザー 3 ケージを取り外し ます。 システム基板上の J_IDSDM コネクタの位置を確認します。 5.
7. 拡張カードライザー 1 を取り付け、ライザーに取り付けるカードがある場合は、取り付けます。 8. システムカバーを閉じます。 9. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 内蔵 SD カード 内蔵 SD カードの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. ライザーに取り付けられているカードがあればそれも含めて、拡張カードライザー 3 を取り外します。 4.
内蔵ストレージコントローラカード お使いのシステムには、システムの内蔵ハードディスクドライブに内蔵ストレージサブシステムを提供する、 内蔵コントローラカード用の専用拡張カードスロットがシステム基板上に装備されています。このコントロ ーラは SAS および SATA ハードディスクドライブをサポートし、お使いのシステムに含まれているストレー ジコントローラのバージョンに応じた RAID 設定で、ハードディスクドライブをセットアップすることも可能 にします。 内蔵ストレージコントローラカードの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1.
図 34. 内蔵ストレージコントローラカードの取り外しと取り付け 1. 2. 3. 4. システム基板上のストレージコネクタ ストレージコントローラカード ストレージコントローラカードホルダ リリースレバー(2) 内蔵ストレージコントローラカードの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを開きます。 3. 冷却用エアフローカバーを取り外します。 4. 拡張カードライザー 1 を取り外します。 5. カードの一方の端をシステム基板上のカードホルダに合わせます。 6.
10. システムカバーを閉じます。 11. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 ネットワークドーターカード ネットワークドーターカードの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. 取り付けられている場合は、拡張カードを拡張カードライザー 2 から取り外します。 4. #2 プラスドライバを使用して、ネットワークドーターカードをシステム基板に固定している 2 本の拘束 ネジを緩めます。 5.
ネットワークドーターカードの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. RJ-45 コネクタが背面パネルのスロットに入る角度にカードを傾けます。 2. カード後端の拘束ネジをシステム基板上の拘束ネジソケットに合わせます。 3. 5. カードコネクタがシステム基板コネクタにしっかり固定されるまで、カードのタッチポイントを押しま す。 #2 プラスドライバを使用して、ネットワークドーターカードをシステム基板に固定する 2 本の拘束ネジ を締めます。 必要に応じて、拡張カードを拡張カードライザー 2 に取り付けます。 6. システムカバーを閉じます。 7.
5. #2 プラスドライバを使用して、ヒートシンク固定ソケットのうち 1 本を緩めます。ヒートシンクとプロ セッサの接続が緩むまで、30 秒ほど待ちます。 6. 2 個目のヒートシンク固定ソケットを外します。 7. ヒートシンクを持ち上げてプロセッサから外します。ヒートシンクは取っておきます。 図 36. プロセッサヒートシンクの取り外しと取り付け 1. 2. 3. 4. ヒートシンク 固定ソケット(2) 固定ネジ(2) プロセッサ 注意: プロセッサは強い圧力でソケットに固定されています。リリースレバーはしっかりつかんで いないと突然跳ね上がるおそれがありますので、注意してください。 8. 9.
図 37. プロセッサシールドのレバー開閉手順 1. 2. 3. 4. 5. ロック施錠シンボル プロセッサソケットリリースレバー プロセッサ プロセッサソケットリリースレバー ロック解除シンボル 10. プロセッサシールドを上方向に持ち上げて、プロセッサが取り出せる状態にします。 注意: ソケットピンは壊れやすく、損傷して修復できなくなることがあります。プロセッサをソケッ トから取り外す際には、ソケットのピンを曲げないように気をつけてください。 11.
図 38. プロセッサの取り外しと取り付け 1. 2. 3. 4. 5. プロセッサソケットリリースレバー ピン 1 インジケータ プロセッサソケットリリースレバー プロセッサシールド プロセッサ 6. ZIF ソケット 7. ソケットキー(4) 8.
メモ: システム BIOS のアップデートは、Lifecycle Controller を使用して行うことができます。 2. 3. 接続されているすべての周辺機器を含むシステムの電源を切り、システムをコンセントから外します。 電源への接続を外したら、カバーを取り外す前に、電源ボタンを 3 秒間押し続けてシステムに蓄えられ た電力を完全に放電します。 システムカバーを開きます。 4. 冷却用エアフローカバーを取り外します。 警告: ヒートシンクとプロセッサは、システムの電源を切った後もしばらくは高温です。ヒートシン クとプロセッサが冷えるのを待ってから作業してください。 5. 注意: プロセッサを取り外そうとしている場合を除き、ヒートシンクをプロセッサから取り外さない でください。ヒートシンクは適切な温度条件を保つために必要です。 ヒートシンク / ヒートシンクダミーおよびプロセッサ / プロセッサダミーを取り外します(該当する場 合)。 6.
メモ: 2 台の電源ユニットを使用する場合は、どちらも同じタイプで最大出力電力も同一である必要があ ります。 ホットスペア機能 お使いのシステムではホットスペア機能がサポートされており、電源ユニットの冗長性に関連する電力のオ ーバーヘッドが著しく軽減されています。 ホットスペア機能を有効に設定すると、冗長電源ユニットがスリープ状態に切り替わります。アクティブな 電源ユニットが負荷の 100% を支えるため、効率良く使用されている状態です。スリープ状態の冗長電源ユニ ットは、アクティブな電源ユニットの出力電圧を監視します。アクティブな電源ユニットの出力電圧が低下 すると、スリープ状態の冗長電源ユニットがアクティブな出力状態に戻ります。 両方の電源ユニットをアクティブにしておく方がスリープ状態の冗長電源ユニットを用意しておくよりも効 率が良い場合は、アクティブな電源ユニットはスリープ状態の電源ユニットをアクティブにすることもでき ます。アクティブな電源ユニットの負荷が 50 パーセントを超えている場合には両方の電源ユニットをウェ イクアップ状態にしておき、負荷が 20 パーセントを下回ると冗長電源ユニットをスリ
図 39. AC 電源装置の取り外しと取り付け 1. 2. 3. 4. コネクタ 電源装置 リリースラッチ 電源装置のハンドル AC 電源ユニットの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 両方の電源ユニットのタイプと最大出力電力が同じであることを確認します。 メモ: 最大出力電力(ワット数で表記)は電源ユニットラベルに記載されています。 2. 電源ユニットダミーが取り付けられている場合は、取り外します。 3.
電源装置ダミーの取り外し 注意: 適切なシステム冷却を確実にするため、非冗長構成では、2 番目の電源装置ベイに電源装置ダミー を取り付ける必要があります。電源装置ダミーを取り外すのは、2 台目の電源装置を取り付けるときの みにしてください。 2 台目の電源装置を取り付ける場合は、電源装置ダミーを外側へ引いて、ベイから取り外します。 図 40. 電源装置ダミーの取り外しと取り付け 1.
1. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 2. システムカバーを開きます。 3. 冷却用エアフローカバーを取り外します。 4. バッテリーソケットの位置を確認します。 注意: バッテリーの取り付け、取り外しの際には、バッテリーコネクタが破損しないようにしっかり 支えてください。 5. バッテリーを取り外すには、コネクタのプラス側をしっかり押し下げてバッテリーコネクタを支えます。 図 41. システムバッテリーの交換 1. バッテリーコネクタのプラス(+)側 2. システムバッテリー 3. バッテリーコネクタのマイナス(-)側 6. バッテリーをコネクタのマイナス側の固定タブから持ち上げて外します。 7. 新しいシステムバッテリーを取り付けるには、コネクタのプラス側をしっかり押し下げてバッテリーコ ネクタを支えます。 8. プラス側を上にしてバッテリーを持ち、コネクタのプラス側にある固定タブの下にスライドさせます。 9. 所定の位置にカチッと収まるまでバッテリーをコネクタに押し込みます。 10.
ハードドライブバックプレーンの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 3. システムカバーを開きます。 注意: ドライブおよびバックプレーンの損傷を防ぐため、バックプレーンを取り外す前にハードドラ イブをシステムから取り外す必要があります。 注意: 後で同じ場所に取り付けることができるように、取り外す前に各ハードドライブの番号を書き 留め、一時的にラベルを貼っておく必要があります。 4. 冷却用エアフローカバーを取り外します。 5.
5. 6. 7. 8. 9. 電源ケーブル A USB ケーブル SAS ケーブル(3) 電源ケーブル B 前面 I/O ケーブル 10. 右コントロールパネルケーブル 11. x12 ハードドライブバックプレーン 12. ハードドライブバックプレーンコネクタ (12) 図 43. ケーブル接続図 — 3.5 インチ(x12)SAS/SATA バックプレーン 1. 2. 3. 4. 5. ケーブル固定ブラケット システム基板 内蔵ストレージコントローラカード システム基板上の SAS コネクタ SAS バックプレーン ハードドライブバックプレーンの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1.
4. 冷却ファンアセンブリを取り付けます。 5. 冷却用エアフローカバーを取り付けます。 6. ハードドライブを元の場所に取り付けます。 7. システムカバーを閉じます。 8. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 9. 前面ベゼルを取り外した場合は、取り付けます。 ハードドライブバックプレーンの取り外し(背面) 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: この手順は、シャーシ背面の 2.5 インチハードドライブ 2 台を取り付けるハードドライブバックプ レーンにのみ適用されます。 1.
図 44. 2.5 インチ(x2)ハードドライブバックプレーン(背面)の取り外しと取り付け 1. 2. 3. 4. 82 パススルー I2C ケーブル I2C ケーブル サイドバンドケーブル ハードドライブバックプレーン(背面) 5. SAS/SATA コネクタ(2) 6. SAS ケーブル 7.
図 45. ケーブル接続図 — 2.5 インチ(x2)ハードドライブバックプレーン(背面) 1. 2. 3. 4. 5. PCIe カードホルダ ハードドライブバックプレーン(背面) システム基板 内蔵ストレージコントローラカード システム基板上の SAS コネクタ 6. ケーブル固定ブラケット 7. x12 または x24 のハードドライブバックプ レーン ハードドライブバックプレーン(背面)の取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: この手順は、シャーシ背面の 2.5 インチハードドライブ 2 台を取り付けるハードドライブバックプ レーンにのみ適用されます。 1.
3. バックプレーンの切り込みをシャーシの切り込みに合わせます。 4. リリースピンを引き上げた状態で、しっかりと固定されるまでバックプレーンをシャーシに挿入します。 5. リリースピンを放してバックプレーンをシャーシに固定します。 6. バックプレーンにすべてのケーブルを接続します。 7. 両方のハードドライブを元の場所に取り付けます。 8. システムカバーを閉じます。 9. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 コントロールパネル コントロールパネルの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1.
図 46. コントロールパネルの取り外しと取り付け 1. 2. 3. 4. Torx ネジ(3) コントロールパネル プルタブ コネクタ 5. ハードドライブバックプレーン 6. シャーシ コントロールパネルの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 3. システムカバーを開きます。 4. ケーブルに付いているラベルを畳みます。 5. コネクタに近い位置にあるプルタブを畳み、コネクタとプルタブをチャネルに挿入します。 6.
11. 前面ベゼルを取り外した場合は、取り付けます。 I/O パネルの取り外し 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 3. システムカバーを開きます。 注意: I/O ケーブルの損傷を防ぐため、ハードドライブバックプレーンのコネクタから I/O ケーブルを 外したり取り付けたりする前に、ロックタブを外す必要があります。 4. ロックを解除するには、I/O ケーブルコネクタのロックタブを時計方向に 90 度回します。 5.
I/O パネルの取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. 前面ベゼルが取り付けられている場合は、取り外します。 2. システムと周辺機器の電源を切り、システムをコンセントから外し、周辺機器をシステムから外します。 3. システムカバーを開きます。 4. ケーブルに付いているラベルを畳みます。 5. チャネルを貫通するまでケーブルを押し込みます。 注意: I/O ケーブルの損傷を防ぐため、ハードドライブバックプレーンのコネクタから I/O ケーブルを 外したり取り付けたりする前に、ロックタブを外す必要があります。 6.
b) c) d) e) f) g) h) i) j) 冷却ファンアセンブリ 電源ユニット すべての拡張カードライザー 内蔵ストレージコントローラカード 内蔵デュアル SD モジュール 内蔵 USB キー(取り付けられている場合) PCIe カードホルダ ケーブル保持ブラケット サポートブラケットが取り付けられている場合は、取り外します。 メモ: システム構成によっては、輸送中の保護のためにサポートブラケットが取り付けられてい る場合があります。取り外し後は処分して構いません。 5. 注意: ミニ SAS ケーブルとコネクタの損傷を防ぐために、システム基板からミニ SAS ケーブルを取 り外す際は正しい手順を守ってください。 次の手順でミニ SAS ケーブルをシステム基板から外します。 a) ミニ SAS ケーブルのコネクタをシステム基板上のコネクタ(J_SASX8)にさらに深く挿入します。 b) ミニ SAS ケーブルコネクタの金属製タブを押し下げた状態に保ちます。 c) ミニ SAS ケーブルをシステム基板上のコネクタから外します。 a. ミニ SAS ケーブルコネクタ b. 金属製タブ 6.
図 48. システム基板の取り外しと取り付け 1. 2. 3. 4. システム基板 システム基板ホルダ リリースピン サポートブラケット(一部のシステムのみ) 警告: ヒートシンクとプロセッサは、システムの電源を切った後もしばらくは高温です。ヒートシン クとプロセッサが冷えるのを待ってから作業してください。 8. ヒートシンク / ヒートシンクのダミーおよびプロセッサ / プロセッサのダミーを取り外します。 9. メモリモジュールとメモリモジュールのダミーカードを取り外します。 10. ネットワークドーターカードを取り外します。 システム基板の取り付け 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1.
3. 注意: システム基板をシャーシに取り付ける際には、システム識別ボタンに損傷を与えないように注 意してください。 タッチポイントを持って、システム基板をシャーシ内に下します。 4. 所定の位置にカチッと固定されるまで、システム基板をシャーシの後方へ押し込みます。 5. 以下を取り付けます。 a) ケーブル保持ブラケット b) PCIe カードホルダ c) 内蔵ストレージコントローラカード d) 内蔵 USB キー(取り付けられている場合) e) 内蔵デュアル SD モジュール f) すべての拡張カードライザー g) 冷却ファンアセンブリ h) 冷却用エアフローカバー i) 電源ユニット 6. すべてのケーブルをシステム基板に接続します。 7. メモ: システム内のケーブルがシャーシ側面に沿って配線され、ケーブル固定ブラケットで固定され ていることを確認します。 システムカバーを閉じます。 8. システムおよびシステムに接続されているすべての周辺機器をコンセントに接続し、電源を入れます。 9.
システムのトラブルシューティング 4 作業にあたっての注意 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: ソリューションの検証は工場出荷のハードウェア構成を使用して行われています。 システム起動エラーのトラブルシューティング 起動時に発生する問題については、画面に表示されるシステムメッセージを書きとめておきます。 外部接続のトラブルシューティング 外付けデバイスのトラブルシューティングを行う前に、すべての外部ケーブルがシステムの外部コネクタに しっかりと接続されていることを確認します。 ビデオサブシステムのトラブルシューティング 1. モニタへのシステムおよび電源接続をチェックします。 2.
8. システムを再起動し、キーボードが機能している場合は、セットアップユーティリティを起動します。 セットアップユーティリティオプションの Integrated Devices(内蔵デバイス)画面で、すべての USB ポ ートが有効化されていることを確認します。 キーボードが機能していない場合は、リモートアクセスも利用できます。システムにアクセスできない 場合は、システム内の NVRAM_CLR ジャンパをリセットし、BIOS をデフォルト設定に復元します。 9. 各 USB デバイスを一度に 1 つずつ再接続し、電源を入れます。 10. 同じ問題が発生するデバイスがあれば、そのデバイスの電源を切り、USB ケーブルを動作確認済みのケ ーブルと交換して、デバイスの電源を入れます。 すべてのトラブルシューティングに失敗する場合は、「困ったときは」を参照してください。 シリアル I/O デバイスのトラブルシューティング 1. システム、およびシリアルポートに接続された周辺機器すべての電源を切ります。 2.
システムが濡れた場合のトラブルシューティング 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1. システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 2. システムカバーを開きます。 3. 以下のコンポーネントをシステムから取り外します。 – ハードドライブ – ハードドライブバックプレーン – USB メモリキー – 冷却用エアフローカバー – 拡張カードライザー(取り付けられている場合) – 拡張カード – 電源ユニット – 冷却ファンアセンブリ(取り付けられている場合) – 冷却ファン – プロセッサとヒートシンク 4.
– 拡張カード – 電源ユニット – 冷却ファンアセンブリ(取り付けられている場合) – 冷却ファン – プロセッサとヒートシンク – メモリモジュール – ハードドライブキャリア – ハードドライブバックプレーン 4. すべてのケーブルが正しく接続されていることを確認します。 5. システムカバーを閉じます。 6.
冷却問題のトラブルシューティング 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 次の状態が発生していないことを確認してください。 • • システムカバー、冷却用エアフローカバー、EMI フィラーパネル、メモリモジュールダミー、または 背面フィラーブラケットが取り外された。 環境温度が高すぎる。 • 外部の通気が遮断されている。 • 冷却ファンが取り外された、または故障した。 • 拡張カードの取り付けガイドラインに準拠していない。 冷却ファンのトラブルシューティング 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホ
5. システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 6. システムカバーを開きます。 7. メモリチャネルをチェックし、正しく装着されていることを確認します。 8. ソケットに装着されている各メモリモジュールを抜き差しします。 9. システムカバーを閉じます。 10. セットアップユーティリティを起動して、システムメモリの設定を確認します。 問題が解決しない場合は、次の手順に進みます。 11. システムカバーを開きます。 12. Diagnostic(診断)テストまたはエラーメッセージで特定のメモリに障害があることが表示された場合、 そのモジュールを動作確認済みのメモリモジュールと取り替え、または交換します。 13.
SD カードのトラブルシューティング 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: 特定の SD カードには、カード上に物理的な書き込み保護スイッチがあります。書き込み保護スイ ッチがオンになっていると、SD カードには書き込みできません。 1. セットアップユーティリティを起動し、Internal SD Card Port(内蔵 SD カードポート)が有効になってい ることを確認します。 2. システムおよび接続されているすべての周辺機器の電源を切り、システムをコンセントから外します。 3.
Diagnostics(診断)テストの結果に応じて、随時次の手順を実行します。 2. システムに RAID コントローラが搭載され、お使いのハードディスクドライブが RAID アレイに設定され ている場合は、次の手順を実行します。 a) システムを再起動し、システム起動中にを押して Lifecycle Controller を実行してから、Hardware Configuration(ハードウェア設定)ウィザードを実行して RAID 設定を確認します。 RAID 設定についての情報は、Lifecycle Controller マニュアルまたはオンラインヘルプを参照してくだ さい。 b) ハードディスクドライブが RAID アレイ用に正しく設定されていることを確認します。 c) ハードディスクドライブをオフラインにして取り外し、再度取り付けます。 d) 設定ユーティリティを終了し、オペレーティングシステムを起動します。 3.
c. 拡張カードのうち 1 枚を取り付けなおします。 d. システムカバーを閉じます。 e. 適切な Diagnostics(診断)テストを実行します。詳細については、「システム診断プログラムの実 行」を参照してください。 テストに失敗した場合は、「困ったときは」を参照してください。 拡張カードのトラブルシューティング 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 メモ: 拡張カードのトラブルシューティングを行う際には、オペレーティングシステムと拡張カードのマ ニュアルを参照してください。 1. 適切な Diagnostics(診断)テストを実行します。詳細については、 「システム診断プログラムの実行」を 参照してください。 2.
1. 2. 適切な Diagnostics(診断)テストを実行します。 実行可能な診断テストについては、「システム診断プ ログラムの実行」を参照してください。 システムおよび接続されている周辺機器の電源を切り、システムをコンセントから外します。 3. システムカバーを開きます。 4. プロセッサとヒートシンクが正しく取り付けられていることを確認します。 5. システムカバーを閉じます。 6.
システム診断プログラムの使い方 5 システムに問題が起こった場合、デルのテクニカルサポートに電話する前にシステム診断プログラムを実行 してください。システム診断プログラムを使うと、特別な装置を使用せずにシステムのハードウェアをテス トでき、データが失われる心配もありません。お客様がご自分で問題を解決できない場合でも、サービスお よびサポート担当者が診断プログラムの結果を使って問題解決の手助けを行うことができます。 Dell Online Diagnostics Dell Online Diagnostics は、診断プログラムまたはテストモジュールのスタンドアロンスイートであり、本番環 境内のシステムでの診断テストの実行を可能にし、システムの稼働時間を最大限に確保するのに役立ちます。 Online Diagnostics を使用して、ハードディスクドライブ、物理メモリ、ネットワークインタフェースカード (NIC)などのストレージコンポーネントやシャーシに診断テストを行うことができます。Online Diagnostics によってシステム上で検知されたハードウェアで診断テストを実行するには、グラフィカル
注意: 内蔵されたシステム診断プログラムは、お使いのシステムをテストする場合にのみ使用してくださ い。このプログラムを他のシステムで使用すると、無効な結果やエラーメッセージが発生する場合があ ります。 1. システム起動中に を押します。 2.
6 ジャンパとコネクタ システム基板のジャンパ設定 パスワード無効化のためのパスワードジャンパのリセットについての情報は、 「忘れてしまったパスワードの 無効化」を参照してください。 表 4.
システム基板のコネクタ 図 49.
項目 コネクタ 説明 11 J_USB USB コネクタ 12 J_VIDEO_REAR ビデオコネクタ 13 J_COM1 シリアルコネクタ 14 J_IDRAC_RJ45 iDRAC7 コネクタ 15 J_CYC システム識別コネクタ 16 CYC_ID システム識別ボタン 17 J_RISER_2A ライザー 2 のコネクタ 18 J_RISER_1A ライザー 1 のコネクタ 19 J_RISER_2B ライザー 2 のコネクタ 20 J_RISER_1B ライザー 1 のコネクタ 21 J_STORAGE 内蔵ストレージコントローラカードのコネク タ 22 J_SASX8 ミニ SAS コネクタ 23 J_USB_INT 内部 USB コネクタ 24 J_SAS_PCH ソフトウェア RAID 用の SAS コネクタ 25 BAT バッテリーコネクタ 26 CPU2 プロセッサソケット 2 27 B10、B6、B2、B9、B5、B1 メモリモジュールソケット 28 J_BP3 バックプレー
項目 コネクタ 説明 42 CPU1 プロセッサソケット 1 43 J_FP_USB 前面パネル USB コネクタ 44 J_BP_SIG1 バックプレーン信号コネクタ 1 45 J_BP_SIG0 バックプレーン信号コネクタ 0 忘れてしまったパスワードの無効化 システムのソフトウェアセキュリティ機能にはシステムパスワードとセットアップパスワードが含まれてい ます。パスワードジャンパでは、これらのパスワード機能を有効化、または無効化して現在使用中の任意の パスワードをクリアすることができます。 注意: 修理作業の多くは、認定されたサービス技術者のみが行うことができます。製品マニュアルで許可 されている範囲に限り、またはオンラインサービスもしくはテレホンサービスとサポートチームの指示 によってのみ、トラブルシューティングと簡単な修理を行うようにしてください。デルで認められてい ない修理による損傷は、保証の対象となりません。製品に付属のマニュアルに記載されている安全上の 注意をよく読んで、その指示に従ってください。 1.
7 仕様 プロセッサ プロセッサのタイプ Intel Xeon プロセッサ E5-2600 シリーズの製品 2 基 拡張バス バスのタイプ PCI Express Generation 3 ライザーカードを使用した拡張スロット: ライザー 1 (スロット 1)ハーフハイトでロープロファイルの x8 リンク (スロット 2)ハーフハイトでロープロファイルの x8 リンク (スロット 3)ハーフハイトでロープロファイルの x8 リンク ライザー 2 (スロット 4)フルハイトでフルレングスの x16 リ ンク メモ: スロット 1 ~ 4 を使用するには、両方のプ ロセッサを取り付ける必要があります。 (スロット 5)フルハイトでフルレングスの x8 リン ク ライザー 3(GPU の交換用) (スロット 6)フルハイトでフルレングスの x16 リ ンク メモリ アーキテクチャ 1600 MT/s DDR3 レジスタ ECC DIMM メモリモジュールソケット 240 ピンソケット 24 個 メモリモジュールの容量 4 GB または 8 GB デュアルランク RAM 32 GB
ドライブ メモ: シャーシ背面に 2.5 インチ SAS または NL SAS (Nearline SAS)ハードドライブ 2 台を搭載できま す。 コネクタ 背面 NIC 10/100/1000 Mbps コネクタ 4 個、および SPF+10 Gbps コネクタ 2 個 シリアル 16550 互換 9 ピン DTE USB 4 ピン USB 2.0 対応コネクタ 2 個 ビデオ 15 ピン VGA 外付け vFlash カード iDRAC7 Enterprise カードを備えたフラッシュメモリ カードスロット 1 個 メモ: このカードスロットは、お使いのシステム に iDRAC7 Enterprise ライセンスがインストール されている場合に限り、使用できます。 前面 USB 4 ピン USB 2.0 対応コネクタ 1 個 ビデオ 15 ピン VGA 内蔵 USB 4 ピン USB 2.
環境 メモ: 動作時の拡張温度範囲で使用すると、シス テムのパフォーマンスに影響が生じる場合があ ります。 メモ: 拡張温度範囲でシステムを使用している 際に、LCD とシステムイベントログに周囲温度 の警告が報告される場合があります。 年間動作時間の 10 パーセント未満 相対湿度 5 ~ 85 パーセント、露点温度 26 °C で、5 ~ 40 °C。 メモ: 標準動作温度範囲(10 ~ 35 °C)外で使用 する場合は、最大年間動作時間の最大 10 パーセ ントまで 5 ~ 40 °C の範囲で動作することがで きます。 35 ~ 40 °C の場合、950 m を超える場所では 175 m 上 昇するごとに最大許容乾球温度を 1 °C 下げます(1 °F/319 フィート)。 年間動作時間の 1 パーセント未満 相対湿度 5 ~ 90 パーセント、露点温度 26 °C で、–5 ~ 45 °C。 メモ: 標準動作温度範囲(10 ~ 35 °C)外で使用 する場合は、最大年間動作時間の最大 1 パーセ ントまで –5 ~ 45 °C の範囲で動作することがで きます。 40 ~ 45 °C の場合
システムメッセージ 8 システムエラーメッセージ システムに問題がある可能性が検知されると、システムメッセージがモニターに表示されます。メッセージ は、システムイベントログ(SEL)に記録されたイベントに基づきます。SEL およびシステム管理設定の詳細 については、システム管理ソフトウェアのマニュアルを参照してください。 メモ: ここに記載されていないシステムメッセージが表示された場合は、そのときに実行していたアプリ ケーションのマニュアルや、OS のマニュアルを参照して、メッセージの説明と推奨されている処置を確 認してください。 メモ: 一部のメッセージでは、特定のシステム部品が名前(<名前>)、コンポーネント番号(<番号>)、 または場所(<ベイ>)で表示される場合があります。 エラーコード AMP0302 メッセージ情報 メッセージ The system board current is greater than the upper warning threshold.
エラーコード ASR0000 ASR0001 ASR0002 ASR0003 BAT0002 メッセージ情報 メッセージ The watchdog timer expired.(ウォッチドッグタイマーがタイム アウトしました。。 ) 詳細 OS またはアプリケーションがタイムアウト時間内に通信でき ませんでした。 対応処置 例外イベントが発生していないか、OS、アプリケーション、ハ ードウェア、システムのイベントログを確認します。 メッセージ The watchdog timer reset the system.(ウォッチドッグタイマーに よってシステムがリセットされました。 ) 詳細 OS またはアプリケーションがタイムアウト時間内に通信でき ませんでした。システムがリセットされました。 対応処置 例外イベントが発生していないか、OS、アプリケーション、ハ ードウェア、システムのイベントログを確認します。 メッセージ The watchdog timer powered off the system.
エラーコード メッセージ情報 対応処置 CPU0000 CPU0001 CPU0005 CPU0010 CPU0023 CPU0204 システムファンをチェックします。問題が解決しない場合は、 「困ったときは」を参照してください。 メッセージ CPU has an internal error (IERR).(CPU <番号> に内部エ ラー(IERR)があります。) 詳細 システムイベントログと OS ログに、例外がプロセッサ外部に あることが示される場合があります。 対応処置 システムイベントログと OS のログを確認します。問題が解決 しない場合は、「困ったときは」を参照してください。 メッセージ CPU has a thermal trip (over-temperature) event.
エラーコード メッセージ情報 対応処置 1. システムの電源を切り、入力電源を 1 分間オフにしておき ます。 2. プロセッサが正しく装着されていることを確認します。 3. 入力電源を入れ、システムの電源をオンにします。 4. 問題が解決しない場合は、 「困ったときは」を参照してく ださい。 CPU0700 メッセージ CPU initialization error detected.(CPU <番号> の初期化エ ラーが検知されました。) 詳細 システム BIOS がプロセッサを初期化できませんでした。 対応処置 1. システムの電源を切り、入力電源を 1 分間オフにしておき ます。 2. プロセッサが正しく装着されていることを確認します。 3. 入力電源を入れ、システムの電源をオンにします。 4. 問題が解決しない場合は、「困ったときは」を参照してく ださい。 CPU0701 メッセージ CPU protocol error detected.
エラーコード メッセージ情報 4. 入力電源を入れ、システムの電源をオンにします。 5. 問題が解決しない場合は、 「困ったときは」を参照してく ださい。 CPU0703 メッセージ CPU bus initialization error detected.(CPU バスの初期化エラーが 検知されました。) 詳細 システムイベントログと OS のログに、例外がプロセッサの外 部にあることが示される場合があります。 対応処置 1. 例外イベントが発生していないか、システムと OS のログ を確認します。例外がない場合は続行します。 2. システムの電源を切り、入力電源を 1 分間オフにしておき ます。 3. プロセッサが正しく装着されていることを確認します。 4. 入力電源を入れ、システムの電源をオンにします。 5. 問題が解決しない場合は、 「困ったときは」を参照してく ださい。 CPU0704 メッセージ CPU machine check error detected.
エラーコード FAN1201 HWC1001 HWC2003 HWC2005 MEM0000 MEM0001 116 メッセージ情報 対応処置 ファンを取り外し、取り付けなおします。問題が解決しない場 合は、「困ったときは」を参照してください。 メッセージ Fan redundancy is lost.(ファンの冗長性が失われました。 ) 詳細 ファンが故障しています。 対応処置 故障したファンを取り外してから再度取り付けるか、追加のフ ァンを取り付けます。 メッセージ The is absent.(<名前> がありません。) 詳細 存在しないデバイスが正常な動作に必要である可能性があり ます。システムの機能が低下する場合があります。 対応処置 ハードウェアを再度取り付けるか、または接続しなおします。 メッセージ The storage cable is not connected, or is improperly connected.
エラーコード MEM0007 MEM0701 MEM0702 MEM1205 メッセージ情報 詳細 メモリモジュールに修正不能なエラーが発生しました。シス テムパフォーマンスが低下する場合があります。その結果、OS やアプリケーションが正常に動作しなくなるおそれがありま す。 対応処置 メモリモジュールを抜き差しします。問題が解決しない場合 は、「困ったときは」を参照してください。 メッセージ Unsupported memory configuration; check memory device at location .
エラーコード MEM1208 MEM8000 PCI1302 PCI1304 PCI1308 118 メッセージ情報 メッセージ Memory spare redundancy is lost. Check memory device at location .(メモリスペアの冗長性が失われました。<場所> の メモリデバイスをチェックしてください。 ) 詳細 メモリスペアリングが使用できなくなっています。 対応処置 メモリモジュールを抜き差しします。問題が解決しない場合 は、「困ったときは」を参照してください。 メッセージ Correctable memory error logging disabled for a memory device at location .
エラーコード PCI1320 PCI1342 PCI1348 PCI1360 PDR0001 メッセージ情報 メッセージ A bus fatal error was detected on a component at bus devicefunction .(バス <バス> デバイス <デ バイス> 機能 <機能> のコンポーネントで、バスの致命的なエラ ーが検知されました。 ) 詳細 システムパフォーマンスが低下するか、またはシステムが動作 しなくなるおそれがあります。 対応処置 入力電源を切って入れなおし、コンポーネントのドライバをア ップデートし、デバイスがリムーバブルの場合は、デバイスを 再び取り付けます。 メッセージ A bus time-out was detected on a component at slot .
エラーコード PDR1016 PST0128 PST0129 PSU0001 PSU0002 PSU0003 120 メッセージ情報 対応処置 障害の発生したディスクを抜き差しします。問題が解決しな い場合は、「困ったときは」を参照してください。 メッセージ Drive is removed from disk drive bay .(ディスクド ライブベイ <ベイ> からドライブ <番号> が取り外されまし た。) 詳細 コントローラがドライブの取り外しを検知しました。 対応処置 ドライブの取り付けを確認します。障害の発生したドライブ を抜き差しします。問題が解決しない場合は、 「困ったときは」 を参照してください。 メッセージ No memory is detected.
エラーコード PSU0006 PSU0016 メッセージ情報 詳細 電源ユニットは正しく取り付けられていますが、入力電源が接 続されていないか、機能していません。 対応処置 入力電源が電源ユニットに接続されていることを確認します。 入力電源が電源ユニットの動作要件を満たしていることを確 認します。 メッセージ Power supply type mismatch.(電源ユニット <番号> の タイプがミスマッチです。) 詳細 電源ユニットは入力タイプと電力定格が一致している必要が あります。 対応処置 一致している電源ユニットを取り付け、このマニュアルで正し い構成を確認します。 メッセージ Power supply is absent.(電源ユニット <番号> がありま せん。 ) 詳細 電源ユニットが取り外されているか、または故障しています。 対応処置 1. 電源ユニットを取り外し、取り付けなおします。 2. システムのケーブルやサブシステムコンポーネントに損 傷がないか確認します。 3.
エラーコード PSU0034 メッセージ情報 詳細 システムパフォーマンスが低下する場合があります。 対応処置 通気および吸気温度を含むシステムの動作環境をチェックし ます。システムログで温度およびサーマルコンポーネント障 害をチェックします。 メッセージ An under voltage fault detected on power supply .(電源ユ ニット <番号> で電圧不足障害が検知されました。 ) 詳細 この障害は、システム内のケーブルまたはサブシステム部品の 電気関係問題の結果である場合があります。 対応処置 1. 電源ユニットを取り外し、取り付けなおします。 2. システムのケーブルやサブシステムコンポーネントに損 傷がないか確認します。 3. 問題が解決しない場合は、「困ったときは」を参照してく ださい。 PSU0035 PSU0036 メッセージ An over voltage fault detected on power supply .
エラーコード PSU1201 PSU1204 PWR1004 PWR1005 PWR1006 メッセージ情報 詳細 電源ユニットは入力タイプと電力定格が一致している必要が あります。 対応処置 一致している電源ユニットを取り付け、このマニュアルで正し い構成を確認します。 メッセージ Power supply redundancy is lost.(電源ユニットの冗長性が失われ ました。) 詳細 電源ユニットは劣化状態での動作を試みます。システムパフ ォーマンスと電源の冗長性が低下するか、または失われる可能 性があります。 対応処置 入力電源を確認します。電源ユニットを取り付けなおします。 問題が解決しない場合は、「困ったときは」を参照してくださ い。 メッセージ The power supplies are not redundant. Insufficient resources to maintain normal operations.
エラーコード RFM1008 RFM1014 RFM1201 メッセージ情報 詳細 システム電力が限度を超えたため、システムが停止しました。 対応処置 システム構成を確認し、電源ユニットをアップグレードする か、システムの電力消費を減らします。 メッセージ Failure detected on Removable Flash Media .(リムーバブル フラッシュメディア <名前> に障害が検知されました。) 詳細 SD カードの読み取りまたは書き込み中にエラーが報告されま した。 対応処置 フラッシュメディアを抜き差しします。問題が解決しない場 合は、「困ったときは」を参照してください。 メッセージ Removable Flash Media is write protected.
エラーコード RFM2006 SEC0031 SEC0033 SEL0006 SEL0008 SEL0012 メッセージ情報 詳細 SD カードモジュールが取り付けられていますが、設定が正しく ないか、初期化ができませんでした。 対応処置 SD モジュールを取り付けなおし、SD カードを抜き差しします。 メッセージ Internal Dual SD Module is write protected.(内蔵デュアル SD モジュール <名前> は書込み防止にされています。) 詳細 モジュールが書込み防止になっています。メディアに変更を 書き込むことができません。 対応処置 意図した状態でない場合は、メディアを取り出し、書込み防止 を解除します。 メッセージ The chassis is open while the power is on.
エラーコード SEL1204 TMP0118 TMP0119 TMP0120 TMP0121 126 メッセージ情報 詳細 システムイベントログが初期化できなかった場合、プラットフ ォームステータスとエラーイベントはキャプチャされません。 一部の管理ソフトウェアはプラットフォームの例外を報告し ません。 対応処置 管理コントローラまたは iDRAC を再起動します。システム入 力電源を切って入れなおします。問題が解決しない場合は、サ ポートにご連絡ください。 メッセージ An unknown system hardware failure detected.
エラーコード VLT0204 メッセージ情報 詳細 室温が高すぎるか、または少なくとも 1 台のファンに障害が発 生している可能性があります。 対応処置 システムの動作環境を確認し、イベントログにファンの障害が 記録されていないか確認します。 メッセージ The system board voltage is outside of the allowable range. (システム基板 <名前> の電圧が許容範囲外です。) 詳細 システムハードウェアが電圧が高すぎるかまたは低すぎる状 態を検知しました。 複数の電圧例外イベントが連続して発生すると、システムはフ ェイルセーフモードになって電源が切れる場合があります。 対応処置 1. 電源ユニットの例外イベントが発生していないか、システ ムログを確認します。 2. システムを最小構成に再構成し、システムケーブルを点検 して取り付けなおします。 3.
困ったときは 9 デルへのお問い合わせ メモ: お使いのコンピュータがインターネットに接続されていない場合は、購入時の納品書、出荷伝票、 請求書、またはデルの製品カタログで連絡先をご確認ください。 デルでは、オンラインまたは電話によるサポートとサービスのオプションを複数提供しています。サポート やサービスの提供状況は国や製品ごとに異なり、国 / 地域によってはご利用いただけないサービスもござい ます。デルのセールス、テクニカルサポート、またはカスタマーサービスへは、次の手順でお問い合わせい ただけます。 1. support.dell.com にアクセスします。 2. サポートカテゴリを選択します。 3. 米国在住以外のお客様は、support.dell.com ページ下の国コードを選択してください。All を選択するとす べての選択肢が表示されます。 必要なサービスまたはサポートのリンクを選択します。 4.