DELL PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガイド TM TM 下記の情報は、参照されているデバイスの製造業者によって提供されており、Dell によって独自に検証されておらず、 下記の制限事項および免責事項 の対象になります。 概要 テープ・ドライブのセットアップ テープ・ドライブの使用 テープ・バックアップ・ソフトウェアの使用 トラブルシューティング 仕様 用語集 注: 「注」は、システムをよりよく活用するために役立つ重要な情報を示します。 注意: 「注意」は、ハードウェアを損傷する、またはデータを失う可能性が想定されることを示し、問題を回避する方法を説明します。 警 告: 「警告」は、物的損害を生じ る、あるいは「怪我」、や「 人が障 害を負う」または「死亡をもたらす」可能性があることをを 示します。 Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved.
目次ページへ戻る 用語集: DELL PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガイド TM TM -A-B-C-D-E-F-G-H-I-J-L-M-N-O-P-R-S-T-U-V-W 数値 2:1 圧縮 (2:1 compression). 圧縮して保管できるデータ量と、圧縮なしで保管できるデータ量との関係。2:1 圧縮は、圧縮なしで保管するデータ量に比 べ、圧縮したほうが 2 倍の量のデータを保管できることを表す。 A A. アンペア (ampere) を参照。 アンペア (A) (ampere (A)). 1 クーロン (C)/秒、または 1 オームの抵抗に 1 ボルトの電圧が加えられて生じる電流の計測単位。 アダプター (adapter). アダプター・カード (adapter card) を参照。 アダプター・カード (adapter card). コンピューターに機能を加える回路ボード。 B バックアップ (backups).
D データ (data). 意味を割り当てる、あるいは意味を割り当てることのできる、文字やアナログ数量などの任意の表現。 データ・カートリッジ (data cartridge). データの保管専用のテープ・カートリッジ。クリーニング・カートリッジ (cleaning cartridge) と対比。 データ圧縮 (data compression). 圧縮 (compression) を参照。 データ転送速度 (data transfer rate). データ伝送システム内の対応する装置の間で、一定時間当たりに渡されるビット、文字、またはブロックの平 均数。速度は、秒、分、または時間当たりの、ビット、文字、またはブロックで表される。 DC. 直流 (direct current) を参照。 消磁 (degauss). テープの磁気を中性化する電流を出す電気コイルに対して、テープを露出して磁気を消すこと。 デバイス (device). テープ・ドライブやテープ・ライブラリーなどの、データを送受信することができるハードウェア・コンポーネントや周辺装置。 デバイス・ドライバー (device driver).
ギガバイト (gigabyte). 1,000,000,000 バイト。 アース (ground). 地表との電気的な接続を持たせるもの。 H ハードウェア (hardware). コンピューターを形成する物理機器またはデバイス。 ヘッド (head). ドライブ・ヘッド (drive head) を参照。 ヘッド耐性測定テスト (Head Resistance Measurements test). ヘッドのテスト診断の一部で、テープ・ドライブのヘッドが正しく作動するかどうかを 判別する手順。このテストは、破損やその他の損傷に耐えられるかどうかヘッドの能力を測定する。 ホスト (host). データ通信構成における制御システム、または最高レベル・システム。 サーバー (server) と同義。 I ID. 識別子 (Identifier)。 in. インチ (inch) を参照。 インチ (inch). 1/36 ヤードまたは 25.4 mm と同等の長さの単位。 入出力 (I/O) (input/output (I/O)).
ループ (loop). (1) 終了条件に達するまで繰り返される一連の命令。 (2) ループを完了するために接続すること。 Low Voltage Differential (LVD). 低ノイズ、低電力、低振幅の電気信号方式システム。これによって、サポートされるサーバーとテープ・ドライブとの 間のデータ通信が可能になる。 LVD 信号方式は、銅線を通じて 1 つの信号を通すのに 2 つのワイヤーを使用する。一対のワイヤーを使用して、電気 的なノイズとクロストークが減る。 LTO. リニア・テープ・オープン (Linear Tape-Open) を参照。 LVD. Low Voltage Differential を参照。 M 磁気テープ (magnetic tape). 磁気記録によってデータを保管することのできる磁化可能な表層を持つテープ。 保 守モード (maintenance mode).
読み取り (read). ストレージ・デバイス、データ・メディア、あるいは別のソースから、データを取得または解釈すること。 リブート (reboot). 初期プログラム・ロード (IPL) 操作を繰り返すことで、プログラムの実行を再初期化すること。 レコード (record). サーバーから提供され、テープ・ドライブによって処理されて記録されるデータ・バイトを区別する最小のセット、およびテープ・ドライ ブによってテープから読み取られ、再処理されて、サーバーで使用できるようにするデータを区別する最小のセット。 相対 湿度 (relative humidity). 同一温度で可能な水蒸気の最大量に対して、大気中に実際に存在する水蒸気の量の比率。 リセット (reset). デバイスまたは回路をクリア状態に戻すこと。 S スクラッチ・カートリッジ (scratch cartridge). 必要なデータが含まれておらず、新しいデータを書き込むことができるデータ・カートリッジのこと。 SCSI. Small Computer Systems Interface を参照。 SCSI バス (SCSI bus).
TapeAlert. テープ・ドライブに関してこれまでに起こった状態や問題を定義する、特許を受けたテクノロジーと ANSI 規格。 TapeAlert フラグ (TapeAlert flags). TapeAlert ユーティリティーによって生成される状況メッセージとエラー・メッセージであり、サーバーのコンソー ルに表示される。 テープ・カートリッジ (tape cartridge). 繰り出しリールとテープ巻き取り機構に巻かれているベルト式の磁気テープを内蔵する、取り外し可能ストレー ジ・ケース。 テープ・ドライブ (tape drive). テープ・カートリッジ内の磁気テープの動きを制御するデータ・ストレージ・デバイス。DELL PowerVault LTO3-060 テー プ・ドライブは、テープからのデータの読み取りとテープへのデータの書き込みを行う機構 (ドライブ・ヘッド) を内蔵している。非圧縮時データ容量は、カ ートリッジ当たり 400 GB。2:1 圧縮時の容量は、最大 800 GB。 テープ・パス (tape path).
目次ページへ戻る 概要: DELL PowerVault TM TM LTO3-060 テープ・ドライブ ユーザーズ・ガイド 概要 SCSI バス・インターフェース 機構 テープ・バックアップ・ソフトウェア フロント・パネル 背面パネル ステータス LED 操作モード アンロード・ボタン 動作モードのステータス LED の解釈 概要 Dell PowerVault LTO3-060 は、高性能の大容量テープ・ストレージ・デバイスで、オープン・システム環境でデータのバックアップと復元、およびファイル のアーカイブと検索を目的として設計されています。このドライブは、タワーまたはラック・サーバーなどのコンピューター・システムに統合することができ ます。Dell PowerVault LTO3-060 テープ・ドライブは、Dell PowerVault 110T LTO-3 テープ・ドライブのハーフハイト・バージョンです。 LTO3-060 テープ・ドライブは、最大 400 GB (2:1 の圧縮率を想定した場合は 800 GB) のフォーマット済みカートリッジ容量、および、60 MB/秒のデータ 転送速度
テープ・ドライブには、以下の機構があります。 l l l l l l l l l l l l l l l l l l 単一の LTO テープ上で 400 GB (非圧縮時)、800 GB (圧縮時*) の容量 高水準データ保全性のための書き込み後読み取り検証を標準装備 60 MB/秒 (非圧縮時)、120 MB/秒 (圧縮時*) のデータ転送速度 128 MB の読み取り/書き込みキャッシュ・メモリー インテリジェント LTO-DC デュアル・モード圧縮アルゴリズム ピン・ピック・エラー・リカバリーを使用するフェイルセーフ・リーダー・キャプチャー機構 LTO カートリッジ・メモリー 安全なバックアップのための TapeAlert サポート Ultra160 LVD SCSI インターフェース スピード・マッチング (システムのデータ転送速度に合わせてテープ・ドライブをスローダウンする) 省電力のためのスリープ・モード Generation 2 カートリッジとの読み取りおよび書き込みの後方互換性 Generation 1 カートリッジとの読み取りの後方互換性 正式な Ultrium LTO ロゴが付いたすべて
1. 電源コネクター 2. SCSI ID コネクター 3. SCSI コネクター ステータス LED 各ステータス LED には次の 4 つのモードがあります。 l l l l オフ オン ゆっくり明滅する (2 Hz) 速く明滅する (8 Hz) 操 作モード ドライブは、次のモードで機能します。 l l 動作モード - 機能には、データおよびクリーニング・カートリッジの使用、エラーの報告、およびファームウェアの更新が含まれます。詳しくは、下 記の 表 2.
緊急時にカートリッジを排出して、ド ライブをリセットする ドライブのアンロード・ボタンを 12 秒間押し続けます。ドライブは現行ドライブ状態のダンプを RAM に保管してか ら、リブートします。リブートの後、カートリッジはテープ開始点にゆっくり巻き戻されます (いくらか時間がかかりま す)。アンロード・ボタンをもう 1 回押すと、カートリッジは排出されます。 重 要: 電 源をサイクル (オフにしてまたオンにすること) しないでください。そうすると、ダンプの内容が消 去されてしまいます。 動 作モードのステータス LED の解釈 フロント・パネルの LED (図 2 の (2 )、(3 )、(4 )、および (5 )) は、ドライブの現行状況を示しています。 次の表では、ドライブが動作モードになっていてエラーが発生していない場合のステータス LED の解釈について説明します。エラーがある場合は、「トラ ブルシューティング」セクションの表 3. 動作モードのステータス LED の解釈 (エラー状態) に進んでください。 表 2.
目次ページへ戻る
目次ページへ戻る テープ・ドライブのセットアップ: DELL PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガ イド TM TM 事前に取り付け済みの内蔵ドライブ 内蔵ドライブの取り付け デバイス・ドライバーのロード ドライブ操作の検証 事 前に取り付け済み の内 蔵ドライブ Dell は、システムの一部として出荷される内蔵テープ・ドライブの取り付けおよびセットアップを行っています。テープ・バックアップ・ソフトウェアがシステ ムに組み込まれている場合は、ソフトウェアに付属のインストール説明書を参照してください。 サポートされる最新のソフトウェア・バージョンについては、 http://www.support.dell.
ス テ ッ プ 2 — シ ス テ ム の電 源を切る 1. システムの電源を切ります。 2.
ご使用のシステムが取り付け用ハードウェアを使用しない場合、シャーシの穴がテープ・ドライブの側面にある穴と位置が合っているか確認してください (図 7 を参照)。 図 7. テープ・ドライブ上の取り付け穴 1. M-3 取り付けねじ穴 ケーブルを設置するためにドライブを動かす必要があるかもしれませんので、この時点ではドライブをねじで固定しないでください。 ス テ ッ プ 7 — 電 源ケーブルおよび S C S I ケーブルを接続す る 図 8 の番号 1 に示すように、システムの内部電源機構にあるスペアの電源ケーブルを電源コネクターに接続します。 図 8 の番号 2 に示すように、システムの SCSI リボン・ケーブルのスペアの SCSI ケーブルを SCSI コネクターに接続します。 注: ドライブが SCSI チェーン上の最後のデバイスである場合は、終端する必要があります。 図 8.
1. 電源コネクター 2. SCSI コネクター ス テ ッ プ 8 — ドライブを固 定す る テープ・ドライブは、いくつかの方法で取り付けることができます。適切な取り付けレールまたはドライブ取り付けスレッドと、正しいねじ (M-3) があること を確認します。一部のシステムでは、ドライブをメディア・ベイに挿入し、システムに直接固定する必要があります。 図 9. ドライブを固 定す る ス テ ッ プ 9 — コンピューターの電 源を接続し て、 テープ・ドライブへの電 源 供 給をテストする 電源コードをシステムおよび電気コンセントに接続します。ドライブが受電していることを確認するには、システムへの電源をオンにしたときに、以下の項 目を監視してください。 1. ブート・プロセス時に、4 つのステータス LED がすべて 2.0 秒間にわたってオンになります。 2. 自己診断テスト (POST) 中に、作動可能ステータス LED (緑色) はゆっくり明滅します。その他すべての LED はオフになります。 3.
す。 インストール手 順 1. ホスト・サーバーまたはワークステーションに管理者特権でログオンしていることを確認します。 2. Dell PowerVault LTO3-060 ドライブ・サポート CD を、ホスト・サーバーまたはワークステーションの CD ドライブに挿入します。 3. Windows デスクトップの「マイ コンピュータ」アイコンを右クリックし、「管 理」をクリックして「デバイス マネージャ」をクリックします。テープ・ドライ ブは、「? そのほかのデバイス」という項目の下に、「IBM Ultrium-HH3 SCSI Sequential Device」として表示されるはずです。 4. 「IBM Ultrium-HH3 SCSI Sequential Device」リストを右クリックし、「削 除」をクリックしてから「O K」をクリックし、デバイスの取り外しを確認し ます。 5. 「コンピュータの管 理」ウィンドウの右の半分にあるメニュー構造の中の一番上の項目を右クリックします。ポップアップ・ウィンドウが表示されま す。 6.
目次ページへ戻る テープ・バックアップ・ソフトウェアの使用: DELL PowerVault LTO3-060 テープ・ドライブ ユー ザーズ・ガイド TM TM ご使用のテープ・バックアップ・アプリケーションで提供されるユーザーの操作ガイドを参照してください。サポートされる最新のソフトウェア・バージョンに ついては、 http://www.support.dell.
目次ページへ戻る 仕様: DELL PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガイド TM TM 一般 製造元 Dell 社向け 型式番号 DELL PowerVault LTO3-060 内蔵テープ・ドライブ インターフェース・タイプ Ultra160 Low Voltage Differential (LVD) SCSI バス 物理仕様 幅 (ベゼルなし) 146.0 mm (5.75 in.) 幅 (ベゼルあり) 148.0 mm (5.83 in.) 長さ (ベゼルなし) 205.5 mm (8.09 in.) 長さ (ベゼルあり) 210.5 mm (8.29 in.) 高さ (ベゼルなし) 41.0 mm (1.6 in.) 高さ (ベゼルあり) 42.7 mm (1.7 in.) 重量 (カートリッジなし) 1.6 kg (3 lbs. 5 oz.) 電源要件 許容度 (+ 5 VDC and + 12 VDC) 電流 (5 VDC) 電流 (12 VDC) +/- 10% 最小 1.3 A / 最大 2.
目次ページへ戻る トラブルシューティング: Dell PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガイド TM TM ドライバーおよびファームウェアのアップグレードの入手 保守モード ダンプの処理 サービス機能の実行 一般ガイドライン ステータス LED を使用するエラー状態の解釈 エラーおよびメッセージの受け取り方 システムによって通知される問題の解決 メディアに関連した問題の解決 テープ・ドライブの取り外し TapeAlert 手動でのテープ・カートリッジの取り外し ドライバーおよびファームウェアのアップグレードの入 手 注 意: ファームウェアを更 新するときには、 更 新が完 了するまではテープ・ドライブの電 源を切らないでください。 電 源を切る と、ファー ムウェアが失われるおそれがあります。 定期的に Web の http://support.dell.
7 トレーニングを受けたサ ービス担当者用に予約済 み トレーニングを受けたサ ービス担当者用に予約済 み 8 速く明滅 速く明滅 速く明滅 状態により異なる2 速く明滅 オン オン 状態により異なる2 1 この機能には、ブランク・データ・カートリッジ (スクラッチ・カートリッジ) が必要です。 2 保守モードのときの障害ライトの状態は、次のようなドライブ・ダンプの存在と場所を示しています。 l l l オフ = メモリー内にダンプはありません 明滅 = RAM (揮発性) メモリーにダンプがあります 点灯 = フラッシュ (不揮発性) メモリーにダンプがあります 注: 明滅の速度: l l ゆっくり明滅 = 2 Hz 速く明滅 = 8 Hz ダンプの処理 診断データの「ダンプ」をドライブ・メモリーに保管すると、問題を診断する上で役立ちます。ダンプの保管に使用できるメモリーの場所には、RAM メモリ ーとフラッシュ・メモリーの 2 つがあります。 RAM メモリーは、ダンプを保管するデフォルトの場所です。RAM のダンプは、新規ダンプが取られると上書 きされます。ドライブの
重要 15 秒以内に次のステップを実行しないと、ドライブはタイムアウトになります。 3. ブランク・データ・カートリッジ (スクラッチ・カートリッジ) を挿入します。数分後、カートリッジはアンロードし、再びロードします。自己診断テストの最 後に、ドライブはカートリッジを排出します。 ¡ 下図を参照して、テストが正常に実行されたか、失敗したかを判別してください。 LED の状態 LED アイコン テストの正常完了 テストの正常終了。ド ライブのクリーニング が必要。 誤ったメディア メディア障害 ドライブ障害 注: l l テストの後、障害ライトがオフである場合はテストは正常に実行されています。テストの後に障害ライトがオンになっている場合、テストは失 敗しました。 テストの後、クリーニング LED はドライブのクリーニングが必要かどうかに応じてオフまたはオンになります。 ボタン: = オフ = オン = ゆっくり明滅 4.
ボタン: = オフ = オン = ゆっくり明滅 = 速く明滅 重要 15 秒以内に次のステップを実行しないと、ドライブはタイムアウトになります。 3. アンロード・ボタンを 1 回押して、サービス機能 2 にアクセスします。ステータス LED は以下のいずれか 1 つの状態になります。 重 要: 障害ステータス LED がゆっくり明滅する場合、ドライブ・ダンプが現在 RAM にあることを示しています。RAM のドライブ・ダンプが上書きさ れる点に注意してください。RAM のドライブ・ダンプの上書きを防止するために、次のステップに進む前に、ダンプを RAM からフラッシュ・メモリー に移動してください (『サービス機能 4 の実行: フラッシュへのダンプのコピー』を参照)。 サービス機能 2。RAM にドライ サービス機能 2。フラッシュ・メモ LED アイコン サービス機能 2 ブ・ダンプがある。* リーにドライブ・ダンプがある。 ボタン: = オフ = オン = ゆっくり明滅 = 速く明滅 4. アンロード・ボタンをダブルクリックして、サービス機能を開始します。 5.
ボタン: = オフ = ゆっくり明滅 = 速く明滅 c. 障害 LED が明滅していることを確認します。 n 障害 LED が明滅している場合、RAM にダンプがあります。 n 障害 LED が明滅していない場合、サービス機能 2 の手順を繰り返してください。 d. 保守モードを終了して作動可能ライトが点灯するまで、アンロード・ボタンを 1 秒あたり 1 回押します。 サービス機能 3 の実行: トレーニングを受けたサービス担当者 用に予 約済み サービス機能 4 の実行: フラッシュへのダンプのコピー 1. カートリッジがドライブに入っていないことを確認します。 注: カートリッジがドライブにロードされている場合、アンロード・ボタンを押すとアンロード要求として解釈され、2 回目と 3 回目を押してもドライブ は無視します。カートリッジがロードされている間、ドライブを保守モードにすることはできません。 2.
ボタン: = オフ = オン = ゆっくり明滅 = 速く明滅 4. アンロード・ボタンをダブルクリックして、サービス機能を活動化します。 5. 作動可能以外のすべてのドライブ・ステータス LED がオフになると、サービス機能は完了です。作動可能 LED は点灯します。これは、ドライブが 保守モードを終了したことを示します。 6. ダンプがフラッシュ・メモリーにあることを確認するには、以下のステップを実行します。 a. カートリッジがドライブに入っていないことを確認します。 注: カートリッジがドライブにロードされている場合、アンロード・ボタンを押すとアンロード要求として解釈され、2 回目と 3 回目を押してもド ライブは無視します。カートリッジがロードされている間、ドライブを保守モードにすることはできません。 b. 作動可能 LED が速く明滅してサービス機能 1 へのアクセスを示すまで、アンロード・ボタンを押し続けます。ステータス LED は以下の状態 になります。 LED アイコン サービス機能 1。フラッシュ・メモリーにドライブ・ダンプがある。 ボタン: = オフ = オン = 速く明滅 c.
は無視します。カートリッジがロードされている間、ドライブを保守モードにすることはできません。 2. 作動可能 LED が速く明滅してサービス機能 1 へのアクセスを示すまで、アンロード・ボタンを押し続けます。ステータス LED は以下のいずれか 1 つの状態になります。 LED の状態 サービス機能 1。メモリー内に ド サービス機能 1。RAM にドライ サービス機能 1。フラッシュ・メモ LED アイコン ライブ・ダンプはない。 ブ・ダンプがある。 リーにドライブ・ダンプがある。 ボタン: = オフ = オン = ゆっくり明滅 = 速く明滅 重要 15 秒以内に次のステップを実行しないと、ドライブはタイムアウトになります。 3.
注: カートリッジがドライブにロードされている場合、アンロード・ボタンを押すとアンロード要求として解釈され、2 回目と 3 回目を押してもド ライブは無視します。カートリッジがロードされている間、ドライブを保守モードにすることはできません。 b. 作動可能 LED が速く明滅してサービス機能 1 へのアクセスを示すまで、アンロード・ボタンを押し続けます。ステータス LED は以下の状態 になります。 LED アイコン サービス機能 1。ダンプはない。 サービス機能 1。RAM にダンプがある。 ボタン: = オフ = ゆっくり明滅 = 速く明滅 c. 障害 LED がオフであることを確認します。 n 障害 LED がオフである場合、フラッシュ・メモリーは消去されています。 n 障害 LED が点灯している場合、サービス機能 4 の手順を繰り返して、フラッシュ・メモリーを消去してください。 d.
l l l ドライブがテープ・カートリッジをアンロードしな い。 す。作動可能 LED ( ) が点灯したら、アンロード・ボタンを押してカートリッジを排出します。 テープ・カートリッジが正しく挿入されなかった。カートリッジを正しく挿入するには、『テープ・カ ートリッジのロード』を参照してください。 テープ・カートリッジに問題がある。別のテープ・カートリッジを挿入してください。複数のカートリ ッジで問題が起こる場合は、ドライブに問題があります。障害のあるドライブを新しいドライブと 取り替えてください。 ドライブに電源が供給されていない。電源をドライブに接続します (『電源を接続して、ドライブ への電源供給をテストする』を参照)。 テープ・カートリッジが詰まっているか、壊れています。アンロード・ボタンを押します。カートリッジが 排出されない場合、アンロード・ボタンを 12 秒間押してドライブをリセットします。ドライブはダンプを RAM に保管し、リブートしてから、カートリッジをテープ開始点まで巻き戻します。カートリッジが最後 まで巻き取られている場合は、最大 10 分間かかります。カートリッジが開始点に
上記の処置を行っても問題が修正されない場合、カスタマー・サポート要員に連絡してください。 3 適正温度を超過した状態では、障害 LED は点灯します。テープがある場合は排出されます。この LED は、ドライブの温度が 2 次温度限界より下ま で低くなるまで点灯したままです。次の 2 つの条件のうち、1 つに適合します。 l l データまたはクリーニング・カートリッジが挿入されている 電源サイクルが行われた ボタン: = オフ = オン = ゆっくり明滅 エラーおよびメッセージの受け取り方 ドライブ、ドライブまたはドライブを使用するシステム・アプリケーションが入ったライブラリーまたはオートローダーからエラー・メッセージを受け取った場 合、表 3 を相互参照として使用してエラーの意味を判別してください。 注: ドライブが動作モードにあるときと、ドライブが保守モードにあるときでは、ドライブのステータス LED の意味が異なります。動作モード時に 起こる LED 状態は、2 つの別々の表で定義しています。ドライブでエラーが起こっていない場合の LED 状態は、『概要』の表 2.
SCSI ターミネーターを交換して、失敗した操作を再試行します。 SCSI ケーブルを交換し、変換コネクターがあればそれも交換して、失敗した操作を再試行します。 n これらの処置によって問題が訂正されない場合は、Dell のテクニカル・サポートに連絡してください。 問題が複数のテープ・ドライブで起こる場合は、エラーのある最初のテープ・ドライブを見つけて、そのテープ・ドライブと変換コネクター (取り 付けられている場合) を接続する SCSI ケーブルを交換します。 n n ¡ S C S I バ ス上の単一ドライブでの非 再 現 性エラーの修 正 1. 2. 3. 4.
TapeAlert フラグ 表 5 に、Dell PowerVault LTO3-060 テープ・ドライブでサポートされる TapeAlert フラグをリストします。 表 5 .
有効期限が切れたクリーニング・カ ートリッジがテープ・ドライブによって クリーニング・カートリッジを取り替えてください。 検出されると、セットされます。 22 16h Expired clean (クリーニング の期限切れ) 23 17h ドライブはクリーニング・カートリッジ Invalid cleaning tape (無効ク を要求したが、ロードされたカートリ 有効なクリーニング・カートリッジを使用してください。 リーニング・テープ) ッジがクリーニング・カートリッジで はなかったときに、セットされます。 30 1Eh Hardware A (ハードウェア A) リカバリーのために、テープ・ドライ ブをリセットする必要があるハード ウェア障害が起こると、セットされま す。 テープ・ドライブをリセットします。『ドライブのリセット』を参照してく ださい。ドライブをリセットしてもエラーをリカバリーできなければ、 本書の『トラブルシューティング』セクションの『一般ガイドライン』を 参照してください。 31 1Fh Hardware B (ハードウェア B) テープ・ドライブが内部の自
4 つの LED がすべて 2 秒間にわたって点灯します。 作動可能 LED はゆっくり明滅しはじめます。 n 作動可能 LED が明滅を停止して点灯すると、POST は完了です。 ドライブはテープ・カートリッジをゆっくりテープ開始点まで巻き戻し、使用できるように位置決めします。 n カートリッジの巻き戻しおよび位置変更の間、アクティビティー LED は明滅します。 n 巻き戻しおよび位置変更の間、作動可能 LED はオンのままです。 作動可能 LED が点灯したままで、アクティビティー LED がオフになると、テープ・ドライブは使用できるようになります。 注: 巻き戻しプロセスが完了するには、少なくとも 10 分かかります。 n n ¡ ¡ 2.
目次ページへ戻る テープ・ドライブの使用: DELL PowerVault LTO3-060 テープ・ドライブ ユーザーズ・ガイド TM TM ドライブの操作 カートリッジのロード、アンロード、およびライト・プロテクト テープ・カートリッジの手入れ テープ機構のクリーニング ドライブの操 作 システムの電源がオンになると、テープ・ドライブもオンになります。テープ・ドライブは電源オン自己診断テスト (POST) を実行します。ハードウェアの自 己診断テスト終了時に、作動可能 LED が緑色で点灯します。 ドライブのリセット ドライブおよびシステムの電源をオフにせずにドライブをリセットできます。これは、ドライブが応答しなくなった場合に必要になります。このリセットを行う には、テープ・ドライブのフロント・パネルにある排出ボタンを 12 秒間押し続けます (図 2 の番号 1 を参照)。ドライブは、大切な技術データのダンプをド ライブ RAM メモリーに強制的にとり、既存のダンプを上書きします。これで、ドライブがリブートして通信可能になります。ロードされているカートリッジが ある場合、ドライブはカートリッジを
l Generation 2 カートリッジは Generation 3 フォーマットには再フォーマットしません。 図 11 に、LTO Ultrium 400-GB データ・カートリッジとそのコンポーネントを示します。 図 11. LTO Ultrium 400-GB データ・カートリッジ 1. 2. 3. 4. 5. 6. LTO カートリッジ・メモリー ラベル域 ライト・プロテクト・スイッチ 挿入ガイド カートリッジ・ドア リーダー・ピン テープ・カートリッジのロード 1. テープ・ドライブの電源がオンになっていることを確認します (作動可能ライトが緑色で点灯)。 2. ライト・プロテクト・スイッチ (図 11 の番号 3 を参照) が正しくセットされていることを確認します。(『カートリッジのライト・プロテクト・スイッチのセッ ト』を参照。) 3. ライト・プロテクト・スイッチがユーザーの方に向くように、カートリッジを持ちます。 4.
は、必ず、バックアップ・ソフトウェアの中の、長いまたはクイックな消去コマンドを使用してください。 テープ・カートリッジのライト・プロテクト・スイッチの位置 (図 13 の番号 1) によって、テープに書き込むことができるかどうかが決まります。 l l このスイッチがロックされている (パッドロックがロックされている) と、テープにデータを書き込むことはできません。 このスイッチがアンロックされている (パッドロックがアンロックされている、または黒の空洞) と、テープにデータを書き込むことができます。 図 13.
1. 通常保管は 1 年未満の保管のことです。 2.