Châssis RAID Dell™ PowerVault™ MD3000i Manuel du propriétaire w w w. d e l l . c o m | s u p p o r t . d e l l .
Remarques, avis et précautions REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : Un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION : Une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document peuvent être modifiées sans préavis.
Sommaire 1 Présentation du système . Présentation . . . . . . . . . . . . . 9 . . . . . . . . . . . . . . . . . . . . . . . . 9 Caractéristiques du châssis . . . . . . . . . . . . 10 . . . . . . . . . . 11 Autres informations utiles . . . . . . . . . . . . . . . 12 Composants de connexion . . . . . . . . . . . . . . . 13 Modular Disk Storage Manager . . . . . . . . . 14 . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . 14 À propos des connexions du châssis .
2 Utilisation du châssis RAID . . . . . . . . . . . 31 Disques physiques, disques virtuels et groupes de disques . . . . . . . . . . . . . . . . . . 31 . . . . . . . . . . . . . . . . . 32 Disques physiques . . . . . . . . . . . . 32 . . . . . . . . . . . . . . . . 34 États des disques physiques Technologie SMART . . . . . . 34 . . . . . . . . . . . . . . 36 RAID 0 . . . . . . . . . . . . . . . . . . . . . . . 36 RAID 1 . . . . . . . . . . . . . . . . . . . . . . . 37 RAID 5 . . .
Fonctions avancées . . . . . . . . . . . . . . . . . . . Partitions de stockage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 52 . . . . . . . . . . . . . . . . 53 Cliché de disque virtuel . . . . . . . . . . 53 . . . . . . . . . . . 54 . . . . . . . . . . . . . . 55 Service de disque virtuel (VDS) Service de cliché instantané des volumes (VSS) . . . . . . Copie de disque virtuel . Utilisation combinée des fonctions de cliché et de copie . . . . . . . . . . . . . . . .
3 Installation des composants du châssis . . . . . . . . . . . . . . Outils recommandés . . . . . . . . . . . 65 . . . . . . . . . . . . . . . . . . 65 Retrait et réinstallation du cadre avant . . . . . . . . . Retrait et installation de disques physiques Retrait de disques physiques installés dans le châssis . . . . . . . . . 67 . . . . . . . . . . . 67 Installation de disques physiques SAS dans le châssis . . . . . . . . . . . . . Retrait et installation d'un module contrôleur RAID . . . . .
4 Dépannage du châssis . . . . . . . . . . . . . . La sécurité d'abord, pour vous et pour le système Routine de démarrage . 83 . . . 83 . . . . . . . . . . . . . . . . . 83 Dépannage des connexions externes Dépannage d'un châssis mouillé . . . . . . . . . 84 . . . . . . . . . . . . 84 Dépannage d'un châssis endommagé . . . . . . . . . 85 Dépannage des blocs d'alimentation . . . . . . . . . . 86 Dépannage des incidents de refroidissement du châssis . . . . . . . . . . . . . . . . . . .
5 Obtention d'aide . . . . . . . . . . . . . . . . . . . Demande d'assistance . . . . . . . . . . . . . . . . . 96 . . . . . . . . . . . . . . . . . . 96 . . . 97 . . . . . . . . . . . . . . . 97 Service automatisé de suivi des commandes Formations Dell Enterprise Incidents liés à votre commande Informations produit . . . . . . . . . . . . 97 . . . . . . . . . . . . . . . . . . . 98 Renvoi d'articles pour une réparation sous garantie ou un remboursement . . . . . . . . . . 98 . . . . .
Présentation du système Le système Dell™ PowerVault™ MD3000i est une baie de stockage RAID externe de 3 unités montée en rack et pouvant accueillir jusqu'à 15 disques SAS (Serial-Attached SCSI) à 3 Gbps. Elle peut être reliée en série à un ou deux châssis d'extension MD1000, ce qui porte à 45 le nombre maximal de disques de la baie de stockage.
Caractéristiques du châssis Les caractéristiques du châssis sont les suivantes : • Prise en charge d'un maximum de 16 serveurs hôtes Microsoft Windows® ou Linux • Châssis de 3 U pour montage en rack • Modules contrôleurs RAID.
• Logiciel de configuration basé sur les tâches (MD Storage Manager) • Fonction Premium (en option) permettant de créer des clichés de disque virtuel (jusqu'à 4 clichés par disque virtuel et 128 par baie) • Fonction Premium (en option) permettant de créer des copies de disque virtuel (jusqu'à 255 par baie) • Surveillance continue des incidents critiques (prévision des pannes de disque physique ou de module contrôleur RAID) effectuée en arrière-plan • Logiciel de basculement installé sur l'hôte.
Autres informations utiles PRÉCAUTION : Le document Product Information Guide (Guide d'information sur le produit) contient d'importantes informations se rapportant à la sécurité et aux réglementations. Les informations sur la garantie se trouvent soit dans ce document, soit à part. 12 • Les documents Rack Installation Guide (Guide d'installation du rack) et Rack Installation Instructions (Instructions d'installation du rack) fournis avec la solution rack décrivent les procédures d'installation.
• Des mises à jour sont parfois fournies pour décrire les modifications apportées au châssis, aux logiciels ou à la documentation. REMARQUE : Vérifiez toujours si des mises à jour sont disponibles sur le site support.dell.com et lisez-les en premier, car elles remplacent souvent les informations contenues dans les autres documents.
À propos des connexions du châssis Le châssis de stockage RAID est connecté à un serveur hôte au moyen de deux modules contrôleurs RAID. Ces modules sont identifiés par les numéros 0 et 1 (voir la figure 1-4). Chaque module contrôleur RAID possède deux ports iSCSI “In” permettant la connexion au serveur hôte. Les ports iSCSI “In” sont identifiés par les numéros 0 et 1.
Figure 1-1. Voyants du cadre avant 1 2 3 Tableau 1-1. Voyants du cadre avant Numéro Voyant 1 Mode divisé (vert) Icône Condition du voyant Ce mode n'étant pas utilisé par le système, le voyant correspondant devrait toujours être éteint. REMARQUE : Le voyant s'allume si le sélecteur de mode situé sur le panneau avant du châssis est sur la position du mode divisé avant la mise sous tension du châssis.
Voyants et caractéristiques du panneau avant La figure 1-2 présente les voyants et les différents éléments situés sur le panneau avant du châssis. Le cadre en option n'est pas représenté. Le tableau 1-2 répertorie les fonctions correspondantes et la signification des voyants. Figure 1-2.
Tableau 1-2. Composants du panneau avant Composant Icône Voyant d'état du châssis (bleu/orange) Condition Orange fixe : le châssis est alimenté en électricité et en cours de réinitialisation. Bleu fixe : le châssis est alimenté en électricité et opérationnel. Bleu clignotant : MD Storage Manager fait clignoter le voyant du châssis. Orange clignotant : une panne du châssis s'est produite.
Voyants des supports de disques physiques Chaque support de disque physique du châssis est équipé de deux voyants : un voyant d'activité (vert) et un voyant d'état bicolore (vert/orange). Voir la figure 1-3. Le voyant d'activité clignote lorsque le système accède à un disque physique. Le tableau 1-3 indique comment interpréter le comportement du voyant d'état. Figure 1-3. Voyants des supports de disques physiques 1 1 Tableau 1-3.
Tableau 1-3. Voyants d'état des supports de disques physiques (suite) Voyant d'état Description Vert clignotant Allumé (400 ms) Éteint (100 ms) Le disque physique est en cours de reconstruction. Orange clignotant (125 ms) Disque physique à l'état “Failed” (Échec) Clignotement vert, orange, puis extinction La possibilité d'une panne du disque physique est signalée par la fonction SMART. Clignotement vert pendant trois La reconstruction du disque physique a été secondes, puis orange pendant annulée.
Figure 1-4. Caractéristiques du panneau arrière 1 2 3 1 Module contrôleur RAID 0 2 Module contrôleur RAID 1 3 Modules de ventilation/ alimentation (2) Modules contrôleurs RAID Les modules contrôleurs RAID présentent différents avantages : hautes performances, configuration avancée des disques virtuels et gestion des sous-systèmes de disques avec tolérance de pannes.
Chaque module contrôleur RAID comprend deux ports iSCSI “In” pour l'accès du système hôte. Ces ports permettent d'établir des connexions hôtes redondantes et prennent en charge les environnements de stockage à haute disponibilité. Selon vos besoins spécifiques en termes de redondance, vous pouvez utiliser différentes configurations pour la connexion du châssis de stockage aux systèmes hôtes (que vous utilisiez un seul ou deux contrôleurs).
• Un port SAS “Out” • Port de débogage Pour obtenir la description des composants d'un module contrôleur RAID, voir le tableau 1-4. Pour plus d'informations sur la connexion du châssis via les ports des modules contrôleurs RAID, reportez-vous au document PowerVault MD3000i Installation Guide (PowerVault MD3000i – Guide d'installation. Figure 1-5. Panneau externe du module contrôleur RAID (vue avant) 1 Tableau 1-4.
Tableau 1-4. Fonctions des composants d'un module contrôleur RAID (suite) Numéro Composant 4 Voyant d'état du port iSCSI “In” 1 (Débit/Activité du lien) Vert : le lien fonctionne à 1000 Mbps. Voyant de panne de la batterie (orange) Orange : l'unité de batterie de sauvegarde ou la batterie est défectueuse ou manquante. 5 Icône Fonction Orange : le lien fonctionne à 100 Mbps. Éteint : la connexion iSCSI est inactive.
Tableau 1-4. Fonctions des composants d'un module contrôleur RAID (suite) Numéro Composant Icône Fonction 11 Voyant de lien Ethernet (vert) Vert : la connexion Ethernet est active. 12 Port de gestion Ethernet Fournit une connexion Ethernet à 10/100 Mbps pour la gestion hors bande du châssis. 13 Voyant de débit Ethernet (vert) Vert : la connexion Ethernet fonctionne à 100 Mbps. Éteint : la connexion Ethernet est inactive. Éteint : la connexion Ethernet fonctionne à 10 Mbps ou est inactive.
Figure 1-6. Module contrôleur RAID 1 2 1 Cache de la batterie 2 Connecteurs pour le fond de panier central (2) Batterie de sauvegarde Chaque module contrôleur RAID contient une batterie de sauvegarde (BBU) à 3 cellules et au lithium-ion, qui alimente sa mémoire cache en cas de coupure de courant. Le contenu de la mémoire cache peut ainsi être conservé pour une durée maximale de 72 heures. Le micrologiciel du module contrôleur RAID teste la BBU au démarrage.
Le module contrôleur RAID enregistre l'âge de la batterie et affiche un rappel indiquant qu'elle doit être remplacée environ 6 semaines avant la date d'expiration. Une fois celle-ci remplacée, utilisez MD Storage Manager pour réinitialiser son âge. Arrêt thermique d'un châssis RAID Les fonctions de gestion comprennent un mécanisme qui arrête le châssis automatiquement lorsque sa température interne dépasse le seuil de sécurité.
Mémoire cache à écriture différée Avec cette méthode, les opérations d'écriture déclenchent l'envoi d'un signal de réussite au système d'exploitation hôte dès que la mémoire cache reçoit les données à écrire. Le disque physique cible recevra les données ultérieurement, à un moment approprié, afin d'optimiser les performances du contrôleur.
Il est possible de remplacer un module de ventilation/alimentation sans mettre le châssis hors tension. Pour plus de détails sur l'installation et le retrait de ces modules, voir “Retrait et installation d'un module de ventilation/alimentation”, à la page 75. La figure 1-7 présente les caractéristiques et les voyants du module de ventilation/alimentation. Le tableau 1-5 contient la description de ces voyants. Figure 1-7.
Tableau 1-5. Voyants des modules de ventilation/alimentation Type Couleur Alimentation en CC Vert Icône Fonction Allumé : les tensions de sortie en CC sont conformes aux spécifications. Éteint : le système n'est pas alimenté, ou bien les tensions ne sont pas conformes aux spécifications. Panne du module de ventilation/ alimentation Orange Alimentation en CA Vert Allumé : la tension de sortie en CC n'est pas conforme aux spécifications, ou bien un ventilateur (voire les deux) est en panne.
Présentation du système
Utilisation du châssis RAID Cette section traite des sujets suivants : • Concepts de base d'une solution RAID : disques physiques, disques virtuels et groupes de disques • Niveaux RAID pris en charge par MD Storage Manager • Fonctionnement des disques de secours et reconstruction • Erreurs de support et secteurs illisibles • Fonctionnement et caractéristiques d'une configuration RAID • Fonctions RAID avancées • Redondance et basculement au niveau du matériel ; informations sur le câblage • Mi
Par exemple, vous pouvez utiliser un disque virtuel pour l'inventaire, un deuxième pour les informations financières et fiscales et un troisième pour les informations sur les clients. Tous les disques virtuels d'un groupe de disques prennent en charge le même niveau RAID. Le châssis RAID prend en charge jusqu'à 256 disques virtuels d'une taille minimale de 10 Mo chacun et pouvant être affectés à des serveurs hôtes.
Tableau 2-1. État des disques physiques reconnus par le module contrôleur RAID (suite) État Mode Description Comportement du voyant d'état des disques physiques Optimal Hot Spare Standby Le disque physique installé (Disque de secours dans l'emplacement indiqué inactif) est configuré en tant que disque de secours. Optimal Hot Spare In Use Le disque physique installé dans Vert fixe (Disque de secours l'emplacement indiqué est utilisé actif) comme disque de secours dans un groupe de disques.
Si la reconstruction d'un disque échoue en raison d'une panne du disque source ou parce que la taille du disque est insuffisante, l'interface utilisateur signale une panne du disque physique. Le voyant d'état du disque indique que la reconstruction a été abandonnée (voyant vert pendant 3 secondes, orange pendant 3 secondes puis éteint pendant 3 secondes).
Création d'un disque virtuel Pour créer un disque virtuel, vous disposez de deux méthodes : • Créer un groupe de disques à partir de l'espace non configuré. Vous pouvez définir le niveau RAID et la capacité (nombre de disques physiques) du groupe de disques, puis définir les paramètres du premier disque virtuel de ce groupe. • Créer un disque virtuel à partir de l'espace disponible d'un groupe de disques existant. Dans ce cas, vous devez uniquement définir les paramètres du nouveau disque virtuel.
Niveaux RAID pris en charge Les niveaux RAID déterminent la façon dont les données sont écrites sur les disques physiques. Il existe plusieurs niveaux RAID offrant différentes possibilités en termes d'accessibilité, de redondance et de capacité. L'utilisation de plusieurs disques physiques (au lieu d'un seul) a plusieurs avantages : • La répartition des données sur plusieurs disques physiques (striping) améliore les performances car les opérations d'E/S peuvent être effectuées simultanément.
RAID 1 Le niveau RAID 1 permet d'écrire les données simultanément sur deux disques physiques. Il est recommandé de l'utiliser pour les bases de données de petite taille ou les applications ne nécessitant pas de capacités importantes. Le RAID 1 permet une mise en redondance totale des données : lorsqu'un disque tombe en panne, le disque miroir prend le relais automatiquement sans aucune perte de données.
Le RAID 0 est le niveau le plus adapté pour les applications de prépresse, d'édition d'images et vidéo, ainsi que pour les applications nécessitant une bande passante importante. Le RAID 1 est très performant en termes de rapidité et de disponibilité des données, mais il entraîne une utilisation des disques plus importante. Il est parfaitement adapté aux applications financières, de comptabilité ou de paie.
Disques de secours et reconstruction L'une des méthodes les plus sûres en matière de protection des données consiste à définir des disques physiques disponibles de la baie de stockage en tant que disques de secours. La présence de tels disques renforce la capacité de tolérance de pannes de la baie. Un disque de secours est un disque physique inactif mais sous tension pouvant être utilisé immédiatement en cas de panne d'un autre disque.
Reconstruction Si un disque faisant partie d'un groupe avec tolérance de pannes (RAID 1, RAID 5 ou RAID 10) devient défectueux et si un disque de secours est disponible, le logiciel RAID tente automatiquement de reconstruire les données pour restaurer la redondance. Si aucun disque de secours n'est disponible, la reconstruction s'effectue automatiquement lorsqu'un nouveau disque physique est installé. Vous pouvez utiliser MD Storage Manager pour indiquer quel disque physique doit être reconstruit.
Fonctionnement et caractéristiques d'une configuration RAID Cette section présente les fonctions RAID suivantes, qui sont prises en charge par le châssis ou le module contrôleur RAID : • Fonctions liées aux disques virtuels • Fonctions liées aux groupes de disques • Priorité des fonctions RAID exécutées en arrière-plan • Migration et itinérance de disques virtuels Fonctions liées aux disques virtuels Initialisation d'un disque virtuel Chaque disque virtuel doit être initialisé.
Initialisation en avant-plan Le micrologiciel du module contrôleur RAID prend en charge l'initialisation complète en avant-plan des disques virtuels. L'accès au disque concerné est bloqué pendant toute la durée de l'opération. Pendant l'initialisation, des zéros (0x00) sont écrits sur chaque secteur du disque virtuel. Celui-ci redevient disponible une fois l'initialisation terminée et sans qu'il soit nécessaire de redémarrer le module contrôleur RAID.
Durée du cycle La vérification des supports est effectuée uniquement sur les groupes de disques sélectionnés, indépendamment des autres groupes. La durée du cycle est le temps requis pour la vérification totale de la région des métadonnées du groupe de disques et de tous les disques virtuels qu'il contient. Le cycle suivant démarre automatiquement une fois le cycle en cours terminé. La durée du cycle d'une vérification des supports peut être définie entre 1 et 30 jours.
Fonctions liées aux groupes de disques Migration du niveau RAID À terme, il est possible que les caractéristiques du niveau RAID que vous utilisiez à l'origine ne soient plus adaptées à votre configuration. Par exemple, vous pouvez ajouter des caractéristiques de tolérance de pannes à un disque configuré en RAID 0 en le convertissant au niveau RAID 5. Sélectionnez le disque virtuel à modifier et le type de niveau RAID souhaité.
• Si le disque virtuel est utilisé dans un environnement mono-utilisateur mais présentant des besoins importants en termes d'E/S (stockage d'applications multimédia, par exemple), vous obtiendrez de meilleures performances si chaque requête est traitée avec une seule bande (correspondant à la taille du segment multipliée par le nombre de disques physiques du groupe qui sont utilisés pour le stockage des données).
Nombre maximal de processus actifs portant sur les groupes de disques Le nombre maximal de processus actifs portant sur les groupes de disques et pouvant être pris en charge simultanément par chaque contrôleur est de 1. Cette limite s'applique aux processus suivants : migration du niveau RAID d'un disque virtuel, migration de la taille de segment, extension de la capacité d'un disque virtuel, extension et défragmentation d'un groupe de disques.
Migration et itinérance de disques virtuels La migration d'un disque virtuel consiste à déconnecter des disques physiques pour les reconnecter à une nouvelle baie afin de déplacer un disque virtuel ou un disque de secours. L'itinérance des disques (disk roaming) consiste à les déplacer d'un emplacement à un autre à l'intérieur d'une baie de stockage. Migration de disques Il est possible de déplacer des disques virtuels d'une baie vers une autre sans mettre la baie cible hors tension.
Utilisez l'une des méthodes suivantes pour déplacer des groupes de disques et des disques virtuels : • Migration à chaud : la migration s'effectue lorsque la baie cible est sous tension. • Migration à froid : la migration s'effectue lorsque la baie cible est hors tension. REMARQUE : Pour vous assurer que les groupes de disques et les disques virtuels migrés seront correctement détectés par une baie cible contenant déjà un disque physique, effectuez une migration à chaud.
REMARQUE : Vous ne devez pas faire migrer simultanément des groupes de disques provenant de plusieurs baies de stockage vers une baie ne contenant aucun disque physique. Pour faire migrer les groupes de disques d'une baie de stockage, effectuez une migration à froid. • Activation des fonctions Premium avant la migration : avant de faire migrer des groupes de disques et des disques virtuels, vous devez activer les fonctions Premium requises sur la baie cible.
Partitions de stockage Le partitionnement du stockage permet aux serveurs hôtes de partager l'accès aux disques virtuels d'une baie. Une partition de stockage est une entité logique composée d'un ou de plusieurs disques virtuels. Elle peut être accessible à un seul serveur hôte ou partagée par plusieurs serveurs hôtes faisant partie d'un même groupe. Avant de créer une partition de stockage, vous devez définir un serveur hôte ou un groupe d'hôtes, puis créer un mappage entre hôte et disque virtuel.
Dans l'un ou l'autre des cas suivants, vous devez utiliser plusieurs partitions de stockage : • Vous souhaitez que des serveurs hôtes spécifiques aient accès à des disques virtuels spécifiques de la baie de stockage. • Les serveurs hôtes connectés à la baie de stockage disposent de systèmes d'exploitation différents. REMARQUE : La baie de stockage peut prendre en charge un maximum de 16 partitions de stockage.
Types de systèmes hôtes En règle générale, un serveur hôte est un serveur qui accède à une baie de stockage. Les serveurs hôtes sont mappés avec les disques virtuels. Ils utilisent un ou plusieurs ports d'initiateur iSCSI et possèdent les attributs suivants : • Nom d'hôte : nom unique identifiant le serveur hôte. • Groupe d'hôtes (utilisé dans les solutions cluster uniquement) : plusieurs serveurs hôtes associés partageant l'accès aux mêmes disques virtuels.
Référentiel de cliché La création d'un cliché de disque virtuel provoque automatiquement celle d'un référentiel de cliché. Un référentiel de cliché est un disque virtuel qui est créé dans la baie de stockage. Il s'agit d'une ressource contenant les métadonnées et les informations de copie sur écriture correspondant à un cliché de disque virtuel spécifique. Chaque référentiel correspond à un seul cliché.
Le programme d'installation du service VDS se trouve dans le répertoire \windows\VDS_VSS du disque MD3000i Resource CD. Pour plus d'information sur ce service, rendez-vous sur le site www.microsoft.com. REMARQUE : Lors de l'enregistrement du service VDS effectué pendant la configuration de Windows, l'interface utilisateur graphique vous invite à indiquer le nom de la baie de stockage car les paramètres de l'interface graphique sont liés à cette dernière et non au système hôte.
Conseils concernant l'utilisation du fournisseur VSS pour la gestion du stockage • Le nombre de clichés pouvant être inclus dans un seul ensemble de clichés varie en fonction du nombre d'E/S traitées par les modules contrôleurs RAID. Ce nombre doit être limité à 8 en cas de charge faible ou nulle et à 3 en cas de forte charge. • Les clichés de disques virtuels créés via le logiciel de gestion du stockage sont des clichés de différentiel. Les clichés plex ne sont pas pris en charge.
Au début du processus de copie, vous devez définir la vitesse souhaitée pour l'opération : si la copie a la priorité la plus élevée, les E/S seront légèrement ralenties, tandis qu'une priorité minimale rendra la copie plus longue. La priorité peut être modifiée en cours de copie. Pour plus d'informations sur la copie d'un disque virtuel, consultez le document MD Storage Manager User's Guide (MD Storage Manager – Guide d'utilisation).
Redondance et basculement au niveau matériel Cette section contient des informations de base qui vous aideront à identifier la méthode de connexion offrant le plus de fiabilité en termes de redondance et de basculement. REMARQUE : Pour optimiser la fiabilité de l'accès aux données, il convient avant tout d'éviter les configurations présentant un point de défaillance, c'est-à-dire un composant ou un chemin non redondant qui, s'il n'est plus disponible, risque d'empêcher tout accès aux données.
Logiciel multiacheminement Le logiciel multiacheminement (également appelé “pilote de basculement”) est un outil installé sur le serveur hôte. Il permet de gérer les chemins de données redondants entre le serveur hôte et le châssis RAID. Pour une gestion correcte du multiacheminement, la redondance doit également être mise en place au niveau physique (connexions iSCSI et câblage).
Retrait ou remplacement d'un module contrôleur RAID Lorsqu'un module contrôleur RAID tombe en panne ou est retiré du châssis RAID, le logiciel de basculement installé sur le serveur hôte transfère toutes les opérations correspondantes sur le module contrôleur RAID secondaire. Les disques virtuels gérés par le contrôleur retiré ou défectueux sont basculés sur le contrôleur restant et les données sont préservées.
Modes de basculement utilisés par les modules contrôleurs RAID Le basculement permet un accès redondant aux disques virtuels gérés par l'un ou l'autre des modules contrôleurs RAID de la baie de stockage. Il est effectué automatiquement et de façon totalement transparente, ce qui permet au(x) serveur(s) hôte(s) de ne jamais perdre l'accès au contrôleur principal auquel appartient le disque virtuel.
Arrêt thermique La gestion du châssis RAID dispose d'une fonction qui arrête automatiquement ce dernier lorsque sa température atteint des niveaux pouvant être dangereux. L'arrêt thermique protège les données stockées sur les disques physiques contre toute altération pouvant résulter d'une panne du système de refroidissement.
Avant de télécharger les fichiers de micrologiciel ou de NVSRAM du module contrôleur RAID, vérifiez que le pilote de multiacheminement (MPP sous Linux ou MPIO sous Windows, par exemple) est en cours d'exécution sur le serveur hôte. Dans une configuration redondante, ce pilote utilise l'un des modules contrôleurs RAID pour permettre aux systèmes hôtes de continuer à accéder aux données pendant la mise à jour de l'autre module contrôleur RAID.
Micrologiciel des châssis d'extension Pour télécharger les mises à jour de micrologiciel destinées aux châssis d'extension MD1000, vous pouvez utiliser MD Storage Manager. Recommandations d'utilisation La baie RAID MD3000i prend en charge diverses configurations. Pour bénéficier de tous les avantages offerts par les fonctions iSCSI et optimiser les performances, tenez compte des recommandations suivantes. • Utilisez un réseau distinct pour le stockage iSCSI.
• Pour plus d'informations concernant la configuration des serveurs hôtes iSCSI en vue de leur utilisation avec les baies d'un réseau de stockage (SAN), reportez-vous au document User's Guide (Guide d'utilisation). Ce guide contient également des informations sur les paramètres avancés des cibles iSCSI. REMARQUE : La modification de ces paramètres entraîne la réinitialisation du port iSCSI.
Installation des composants du châssis Cette section indique comment installer les composants suivants : • Cadre avant (facultatif) • Disques physiques et supports • Modules contrôleurs RAID • Batterie de sauvegarde • Blocs d'alimentation • Panneau de commande • Fond de panier central du châssis Outils recommandés Les procédures présentées dans cette section nécessitent notamment l'utilisation des outils suivants : • Tournevis n° 2 à tête cruciforme • Tournevis Torx T10 • Bracelet anti-st
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Retrait et réinstallation du cadre avant Pour accéder aux disques physiques installés dans le châssis, vous devez retirer le cadre avant (fourni en option). Si ce cadre n'est pas installé, ne tenez pas compte de cette section. Pour retirer le cadre : 1 Si le cadre est fermé à clé, insérez la clé dans le verrou. Sinon, passez à l'étape 3. 2 Tournez la clé vers la gauche pour ouvrir.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Retrait et installation de disques physiques Le châssis peut accueillir jusqu'à 15 disques physiques SAS à 3 Gbps installés dans des supports de disque individuels. Ces disques physiques sont connectés directement au fond de panier central du châssis. Ils sont enfichables à chaud et peuvent donc être installés et retirés sans qu'il soit nécessaire de mettre le châssis hors tension.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-2. Installation et retrait de disques physiques 1 2 1 Mécanisme d'éjection du support 2 Poignée du support de disque 3 Ouvrez la poignée du support en la faisant tourner vers le bas. 4 Retirez le support de son logement tout en mettant une main sous le disque pour le maintenir.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Installation de disques physiques SAS dans le châssis AVIS : Pour assurer une ventilation et un refroidissement corrects du châssis, chaque logement doit contenir un disque physique actif ou un cache. PRÉCAUTION : Portez toujours un bracelet anti-statique lorsque vous manipulez un appareil comprenant des composants sensibles à l'électricité statique.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-3. Installation d'un disque physique SAS dans un support 2 1 3 1 Vis (4) 2 Support du disque 3 Disque physique 2 La poignée du support étant ouverte, alignez le guide du rail coulissant du support avec celui situé sur le châssis, puis mettez le disque physique en place. Voir la figure 3-2. 3 Poussez le support de disque dans son emplacement jusqu'à ce que la base du levier entre en contact avec la façade du châssis.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm 4 Fermez le levier tout en continuant à pousser le support dans le logement. Si le disque est installé correctement, le voyant d'état s'allume en vert et reste fixe. Voir le tableau 1-3. Si le voyant ne s'allume pas, voir “Dépannage des disques physiques SAS”, à la page 89. REMARQUE : Le châssis doit contenir au moins deux disques physiques.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-4. Retrait et installation d'un module contrôleur RAID 2 1 1 Patte de dégagement 2 Levier d'éjection Installation d'un module contrôleur RAID 1 Insérez doucement le module contrôleur RAID dans le logement vide. 2 Poussez-le vers le fond du logement jusqu'à ce qu'il soit fermement emboîté dans le connecteur du fond de panier. Voir la figure 3-4.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Retrait et installation de la batterie de sauvegarde d'un module contrôleur RAID Chaque module contrôleur RAID est équipé d'une batterie qui fournit l'alimentation nécessaire à la sauvegarde des données stockées en mémoire cache. Cette batterie est montée à l'intérieur du module contrôleur RAID et connectée à la carte à circuits imprimés de ce dernier. Cette section explique comment retirer et réinstaller la batterie de sauvegarde.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-5. Retrait et installation de la batterie de sauvegarde d'un module contrôleur RAID 3 2 1 1 Vis moletée 2 Cache de la batterie 3 Batterie 4 Retirez la vis moletée qui fixe la batterie au module contrôleur. 5 Dégagez la batterie de son connecteur en la poussant vers l'arrière du contrôleur, puis retirez-la.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Retrait et installation d'un module de ventilation/alimentation Le châssis peut accueillir deux modules distincts contenant chacun un bloc d'alimentation intégré et deux ventilateurs. Bien que le châssis puisse fonctionner temporairement avec un seul bloc d'alimentation, les deux modules de ventilation (chacun contenant deux ventilateurs) sont nécessaires pour assurer une ventilation correcte.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-6. Réinstallation du bloc d'alimentation 4 3 1 1 Bloc d'alimentation 4 Interrupteur marche/arrêt 2 2 Vis imperdables (2) 3 Poignée PRÉCAUTION : Les modules de ventilation/alimentation sont lourds. Utilisez vos deux mains pour les manipuler. 3 Saisissez la poignée du bloc d'alimentation et retirez doucement le module de la baie. Voir la figure 3-6.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Installation d'un module de ventilation/alimentation 1 Insérez le nouveau module dans la baie vide, sur environ les deux tiers de la longueur. 2 Poussez le module jusqu'au fond du logement, jusqu'à ce qu'il soit fermement emboîté dans le connecteur de fond de panier. Lorsque le bloc d'alimentation est correctement installé, sa face avant est alignée avec celle du bloc d'alimentation voisin.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm 5 Retirez tous les disques physiques du châssis. Voir “Retrait et installation de disques physiques”, à la page 67. REMARQUE : Pour éviter les inversions, notez le numéro d'emplacement de chaque disque immédiatement après l'avoir retiré. Figure 3-7.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Installation du panneau de commande 1 Alignez les pattes inférieures et supérieures du panneau de commande sur les encoches d'insertion situées au bord du châssis. Voir la figure 3-7. 2 Insérez le panneau de commande dans le logement, en vous assurant que le connecteur s'emboîte dans le connecteur approprié du fond de panier. Voir la figure 3-7.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-8. Retrait et réinstallation du bâti des contrôleurs et des blocs d'alimentation 1 2 1 Vis cruciformes (4) 2 Bâti des contrôleurs et des blocs d'alimentation 5 Faites glisser le bâti des contrôleurs et des blocs d'alimentation hors du châssis et mettez-le de côté.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.fm Figure 3-9.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\install.
Dépannage du châssis La sécurité d'abord, pour vous et pour le système Certaines procédures décrites dans ce document impliquent une intervention à l'intérieur du châssis. Lorsque vous intervenez sur le châssis, suivez strictement les opérations décrites dans ce guide ou dans une autre documentation. PRÉCAUTION : Seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du châssis pour accéder aux composants internes.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Dépannage des connexions externes Les incidents les plus courants sont dus à un branchement incorrect des câbles ou à des broches tordues. Vérifiez que tous les câbles externes sont fermement raccordés aux connecteurs externes et qu'aucun de ces connecteurs n'est endommagé. Voir “Voyants et caractéristiques du panneau arrière”, à la page 19 pour obtenir la description des connecteurs situés sur le panneau arrière du châssis.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm 6 Laissez le châssis sécher pendant au moins 24 heures. 7 Réinstallez tous les composants retirés à l'étape précédente. 8 Rebranchez le châssis sur la prise secteur et mettez-le sous tension. Si le châssis ne démarre pas normalement, voir “Obtention d'aide”, à la page 95. Dépannage d'un châssis endommagé Incident • Le châssis est tombé ou a été endommagé.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Dépannage des blocs d'alimentation Incident • Les voyants d'état du châssis indiquent qu'un incident s'est produit. • Les voyants de panne des blocs d'alimentation sont allumés. Action PRÉCAUTION : Seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du châssis pour accéder aux composants internes.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm 3 Retirez et réinstallez le bloc d'alimentation pour vous assurer qu'il est bien en place. Voir “Retrait et installation d'un module de ventilation/ alimentation”, à la page 75. REMARQUE : Après avoir installé un bloc d'alimentation, attendez quelques secondes pour laisser au châssis le temps de le reconnaître et déterminer s'il fonctionne correctement. AVIS : Les modules de ventilation/alimentation sont enfichables à chaud.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Action Vérifiez qu'aucune des conditions suivantes n'est présente : • La température ambiante est trop élevée. • La circulation de l'air extérieur est bloquée. • Un module de ventilation/alimentation est défectueux. Voir “Dépannage d'un ventilateur”, à la page 88. Dépannage d'un ventilateur Incident • Le voyant d'état du châssis est orange.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Dépannage des disques physiques SAS PRÉCAUTION : Seuls les techniciens de maintenance qualifiés sont habilités à retirer le capot du châssis pour accéder aux composants internes.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm 3 Inspectez le disque et les connecteurs destinés au fond de panier central pour voir s'ils sont endommagés. 4 Réinstallez le disque dans sa baie d'origine. Voir “Retrait et installation de disques physiques”, à la page 67. Si l'incident persiste, voir “Obtention d'aide”, à la page 95. Incident • Plusieurs disques physiques ne sont pas détectés par MD Storage Manager.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Dépannage des connexions du châssis Incident • Le châssis n'est pas détecté par le serveur hôte connecté. Action • Inspectez les câbles des modules contrôleurs RAID pour vérifier qu'il n'existe aucun problème de connectivité (câbles endommagés ou mal raccordés, connexions de mauvaise qualité, etc.).
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Erreurs ECC Que le module contrôleur RAID soit utilisé dans une configuration redondante ou non redondante, son micrologiciel peut détecter les erreurs ECC et effectuer une récupération en cas d'erreur ECC portant sur un seul bit. Une baie de stockage contenant des modules contrôleurs RAID redondants peut également effectuer une récupération après des erreurs ECC multibits, car le second contrôleur peut, au besoin, prendre le relais.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.fm Conditions non critiques Une condition non critique est un événement ou un état qui ne provoque pas de panne immédiate mais doit être corrigé pour que le fonctionnement de la baie reste fiable. Exemples d'événements non critiques : • Un bloc d'alimentation est défectueux. • Un ventilateur est défectueux. • Un module contrôleur RAID inclus dans une configuration redondante est défectueux.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\trouble.
Obtention d'aide Demande d'assistance PRÉCAUTION : Avant de retirer le capot du système, débranchez l'ordinateur et le modem de toutes les prises secteur. 1 Suivez les procédures de la section “Dépannage du châssis”, à la page 83. 2 Vérifiez l'état de la baie de stockage sous MD Storage Manager et notez toutes les informations fournies. 3 Pour vous aider lors des procédures d'installation et de dépannage, utilisez toute la gamme de services en ligne proposés par Dell sur le site support.dell.com.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\GetHelp.fm Support technique et service clientèle Le service de support de Dell est à votre disposition pour répondre à vos questions concernant le matériel Dell™. Notre équipe de support technique utilise des diagnostics assistés par ordinateur pour répondre plus rapidement et plus efficacement à vos questions.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\GetHelp.fm • Adresses e-mail du service Marketing et ventes de Dell apmarketing@dell.com (région Asie/Pacifique uniquement) sales_canada@dell.com (Canada uniquement) • Protocole de transfert de fichiers (FTP) anonyme ftp.dell.com/ Connectez-vous en tant que user : anonymous et indiquez votre adresse e-mail comme mot de passe.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\GetHelp.fm Informations produit Si vous avez besoin d'informations à propos d'autres produits disponibles chez Dell, ou si vous désirez passer une commande, consultez le site Web de Dell à l'adresse www.dell.com. Pour trouver le numéro de téléphone à appeler pour parler à un spécialiste des ventes, consultez les informations de contact de votre région.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\GetHelp.fm Avant d'appeler REMARQUE : Ayez votre code de service express à portée de main quand vous appelez. Le code permet au système d'assistance téléphonique automatisé de Dell de diriger votre appel plus efficacement. Si possible, allumez le système avant d'appeler Dell pour obtenir une assistance technique et utilisez un téléphone qui se trouve à côté de l'ordinateur.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\GetHelp.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm Glossaire Cette section définit ou identifie les termes techniques, abréviations et sigles utilisés dans la documentation fournie avec le système. A : Ampère(s). ACPI : Acronyme de “Advanced Configuration and Power Interface”. Interface standard qui permet au système d'exploitation de contrôler les paramètres relatifs à la configuration et à la gestion de l'alimentation. adresse MAC : Adresse de contrôle d'accès aux supports.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm BIOS : Acronyme de “Basic Input/Output System”, système d'entrées/sorties de base. Le BIOS du système contient des programmes stockés sur une puce de mémoire flash. Le BIOS contrôle : • les communications entre le processeur et les périphériques, • diverses fonctions, comme les messages du système. bit : Plus petite unité d'information interprétée par le système.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm carte d'extension : Carte supplémentaire (par exemple un adaptateur SCSI ou un NIC) qui se branche dans un connecteur d'extension sur la carte système de l'ordinateur. Une carte adaptateur ajoute des fonctions spéciales au système en fournissant une interface entre le bus d'extension et un périphérique. carte hôte : Carte assurant la communication entre le bus du système et le contrôleur d'un périphérique.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm COMn : Nom de périphérique associé aux ports série du système. combinaison de touches : Commande exécutée en appuyant sur plusieurs touches en même temps (par exemple ). composant : Dans le contexte de l'interface DMI, il s'agit d'un élément compatible DMI, comme un système d'exploitation, un ordinateur, une carte d'extension ou un périphérique.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm DIN : Acronyme de “Deutsche Industrie-Norm”, norme de l'industrie allemande. disque physique : Disque dur installé dans le châssis RAID. disquette d'amorçage : Disquette utilisée pour démarrer le système si celui-ci ne peut pas être initialisé à partir du disque physique. disquette système : Voir disquette d'amorçage. DMA : Acronyme de “Direct Memory Access”, accès direct à la mémoire.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm EMC : Acronyme de “Electromagnetic Compatibility”, compatibilité électromagnétique. EMI : Acronyme de “ElectroMagnetic Interference”, interférence électromagnétique. EMM : Module de gestion du châssis. enfichable à chaud : Se dit d'un composant ou d'un périphérique pouvant être déconnecté du système sans qu'il soit nécessaire de mettre ce dernier hors tension.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm fichier system.ini : Fichier de démarrage du système d'exploitation Windows. Quand vous lancez Windows, il consulte le fichier system.ini pour déterminer une variété d'options pour l'environnement d'exploitation Windows. Entre autres, le fichier system.ini indique les pilotes vidéo, souris et clavier qui sont installés pour Windows. fichier win.ini : Fichier de démarrage du système d'exploitation Windows.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm Hz : Hertz. ID : Identification. IDE : Acronyme de “Integrated Drive Electronics”. Interface standard entre la carte système et les périphériques de stockage. informations de configuration du système : Données stockées en mémoire, qui informent un système sur la manière dont le matériel est installé et dont le système doit être configuré pour fonctionner. IP : Acronyme de “Internet Protocol”, protocole Internet.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm Ko/s : Kilo-octets par seconde. KVM : Commutateur KVM. Le terme KVM désigne un commutateur qui permet de sélectionner le système correspondant à la sortie vidéo affichée et sur lequel le clavier et la souris sont utilisés. lame : Module équipé d'un processeur, de mémoire et d'un disque physique. Ces modules sont montés dans un châssis équipé de blocs d'alimentation et de ventilateurs. LAN : Réseau local.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm mémoire cache : Zone de mémoire rapide contenant une copie des données ou des instructions pour les récupérer plus vite. Quand un programme demande des données qui se trouvent dans la mémoire cache, l'utilitaire de mise en mémoire cache du disque physique peut extraire les données plus vite de la RAM que du disque même. mémoire conventionnelle : Les 640 premiers kilo-octets de la RAM.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm mode graphique : Mode vidéo qui peut être défini par le nombre de pixels horizontaux x, le nombre de pixels verticaux y et le nombre de couleurs z.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm NVRAM : Mémoire vive rémanente. Mémoire qui ne perd pas son contenu lorsque le système est mis hors tension. La NVRAM est utilisée pour conserver la date, l'heure et la configuration du système. panneau de commande : Pièce du système sur laquelle se trouvent les voyants et les contrôles (bouton d'alimentation, voyant d'alimentation, etc.). parité : Informations redondantes associées à un bloc de données.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm pilote vidéo : Programme qui permet aux applications exécutées en mode graphique et aux systèmes d'exploitation d'afficher les données avec la résolution et le nombre de couleurs voulus. Le pilote vidéo doit correspondre à la carte vidéo installée. pixel : Point sur un écran vidéo. Les pixels sont disposés en lignes et en colonnes afin de créer une image.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm RAID : Acronyme de “Redundant Array of Independent Disks”, matrice redondante de disques indépendants. Technologie permettant la mise en redondance des données. Les niveaux RAID les plus utilisés sont les niveaux 0, 1, 5, 10 et 50. Voir aussi guarding, mise en miroir et striping. RAM : Acronyme de “Random-Access Memory”, mémoire vive. Zone principale de stockage temporaire du système pour les instructions d'un programme et les données.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm rpm : Acronyme de “Revolutions Per Minute”, tours par minute. RTC : Acronyme de “Real-Time Clock”, horloge temps réel. SAN : Acronyme de “Storage Area Network”, réseau de stockage. Environnement dans lequel la technologie Fibre Channel est utilisée pour relier des ordinateurs et des systèmes de stockage. Les réseaux SAN permettent d'éviter les goulets d'étranglements habituellement rencontrés sur les réseaux.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm spanning (concaténation) : Dans ce mode, les volumes de disques attachés sont combinés ensemble et vus par le système d'exploitation comme un disque physique unique. L'espace disponible est ainsi mieux utilisé. striping (répartition des données) : Méthode de répartition des données sur trois ou plusieurs disques, en utilisant une quantité donnée d'espace sur chacun. L'espace occupé par une bande (”stripe”) est le même sur chaque disque.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.fm utilitaire : Programme qui sert à gérer les ressources du système (mémoire, disques durs, imprimantes, etc.). UTP : Acronyme de “Unshielded Twisted Pair”, paire torsadée non blindée. Type de câblage utilisé pour relier un ordinateur à une ligne téléphonique. V : Volt(s). VCA : Volts en courant alternatif. VCC : Volts en courant continu. VGA : Acronyme de “Video Graphics Array”, matrice graphique vidéo.
FILE LOCATION: H:\Enterprise\Bulldog\DL1125 - HOM A00\FR\Glossary.
Index B D Bloc d'alimentation Caractéristiques, 27 Dépannage, 86 Installation et retrait, 75 Voyants, 29 Dell Contacter, 99 C Cadre avant Retrait et réinstallation, 66 Voyants, 15 Châssis Caractéristiques, 10 Non valide, 91 Conditions de verrouillage, 91 Connexion du châssis Dépannage, 91 Connexions externes Dépannage, 84 Contacter Dell, 99 Contrôleur Incident, 91 Coordonnées téléphoniques, 99 Dépannage, 83 Blocs d'alimentation, 86 Connexion du châssis, 91 Connexions externes, 84 Disque physique, 89 Re
E Erreur ECC, 92 F Fond de panier central Installation et retrait, 79 Module contrôleur RAID États, 92 Installation et retrait, 71 Modes de basculement, 60 Retrait/remplacement, 59 Voyants, 91 Module de gestion du châssis, 20 N G Garantie, 12 Groupe de disques Défragmentation, 45 Description, 31 L Logiciel de gestion du stockage. Voir MD Storage Manager.
S Sécurité, 83 Seuils de température, 26, 61 Station de gestion du stockage, 11 Support Contacter Dell, 99 Système endommagé Dépannage, 85 T Test de cohérence, 42 V Ventilateur Caractéristiques, 27 Dépannage, 88 Vérification des supports, 42 Voyants du panneau avant DEL, 17 Index 121
Index