Dell PowerVault MD3200i and MD3220i Storage Arrays Getting Started With Your System Guide de mise en route Introdução ao uso do sistema Introducción al sistema
Dell PowerVault MD3200i and MD3220i Storage Arrays Getting Started With Your System Regulatory Model Series E03J and E04J
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this publication is subject to change without notice. © 2011 Dell Inc. All rights reserved.
Before You Begin NOTE: Throughout the document, Dell PowerVault MD3200i series storage array refers to both Dell PowerVault MD3200i and Dell PowerVault MD3220i. Dell PowerVault MD1200 series expansion enclosure refers to both Dell PowerVault MD1200 and Dell PowerVault MD1220. Before setting up your Dell PowerVault MD3200i series storage array, you must consider certain best practices to ensure that your storage array operates at maximum efficiency and offers full redundancy (if required).
Completing the iSCSI Worksheet IPv4 Settings A host server 192.168.133.101 (In 3 default) Mutual CHAP Secret 192.168.128.101 (management network port) 192.168.132.101 (In 2 default) 192.168.131.101 (In 1 default) 192.168.130.101 (In 0 default) Target CHAP Secret B PowerVault MD3200i series storage array 192.168.130.102 (In 0 default) 192.168.131.102 (In 1 default) 192.168.132.102 (In 2 default) 192.168.133.102 (In 3 default) 192.168.128.
B Static IP address (storage array) Subnet mask Default gateway iSCSI controller 0, In 0 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ iSCSI controller 0, In 1 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ iSCSI controller 0, In 2 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ iSCSI controller 0, In 3 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ Management port cntrl 0 ___ . ___ . ___ . ___ ___ . ___ . ___ .
• The SMI-S Programmer’s Guide provides information about using the SMI-S provider and SMI-S programming. • Any media that ships with your system that provides documentation and tools for configuring and managing your system, including those pertaining to the operating system, system management software, system updates, and system components that you purchased with your system. NOTE: Always check for updates on support.dell.
Common Configurations Cabling Your Direct-Attached Hosts Server 1 Server 2 Server 3 Server 4 Storage array Corporate, public, or private network Getting Started With Your System 7
Cabling Your SAN-Attached Hosts Server Switch 1 Switch 2 Storage array Corporate, public, or private network 8 Getting Started With Your System
Up to 32 hosts Server 1 Server 2 Switch 1 Switch 2 Storage array Corporate, public, or private network Getting Started With Your System 9
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. Unpacking the System Unpack your system and identify each item with the packing list that shipped with your system. Installing the Rails and System in a Rack Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your system.
Connecting the Power Cable(s) Ensure that the power switch is in the OFF position before connecting the power cables. Connect the system’s power cable(s) to the system. Securing the Power Cable(s) Secure the cable(s) firmly to the bracket using the provided strap. Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Each power supply must be connected to a separate power circuit.
Cabling Your Expansion Enclosure PowerVault MD1200 series expansion enclosure 2 (optional) PowerVault MD1200 series expansion enclosure 1 (optional) PowerVault MD3200i series storage array Turning On the Enclosure 12 Getting Started With Your System
Turn on components in the following order 1 Ethernet switches (if used) 2 PowerVault MD1200 series expansion enclosures (if used) NOTE: Before turning on the storage array, ensure that the expansion enclosure status LED is blue. 3 PowerVault MD3200i series storage array NOTE: Before turning on the host server(s), ensure that the storage array status LED is blue. 4 Host server(s) Installing the Bezel Install the bezel (optional).
iSCSI host ports, and creating sessions for the iSCSI modular disk storage arrays. It is recommended that you use MDCU to configure iSCSI on each host server connected to the storage array. To install the MD storage software: 1 Insert the MD series resource media. Depending on your operating system, the installer may launch automatically. If the installer does not launch automatically, navigate to the root directory of the installation media (or downloaded installer image) and run the md_launcher.exe file.
9 When the reboot is complete, the MDCU may launch automatically. If the MDCU does not launch automatically, launch it manually. • In a Windows-based operating system, click Start→ Dell→ Modular Disk Configuration Utility. • In a Linux-based operating system, double-click the Modular Disk Configuration Utility icon on the desktop. NOTE: If MDCU is not installed, see the Deployment Guide at support.dell.com/manuals. 10 Start the MD Storage Manager and discover the array(s).
NOM Information (Mexico Only) The following information is provided on the device described in this document in compliance with the requirements of the official Mexican standards (NOM): Importer: Model number: Supply voltage: Frequency: Current consumption: E03J and E04J 100–240 V CA 50/60 Hz 8.6 A Technical Specifications Drives PowerVault MD3200i Up to twelve 3.5-inch SAS hot-swappable hard drives (3.0 Gbps and 6.0 Gbps) PowerVault MD3220i Up to twenty four 2.5-inch SAS hot-swappable hard drives (3.
Back-Panel Connectors (Per RAID Controller Module) (continued) Management Ethernet connector One 100/1000 Base-T port Ethernet for out-of-band management of the enclosure NOTE: The default management port IP addresses for the primary and secondary RAID controller modules are 192.168.128.101 and 192.168.128.102, respectively. By default, the management ports are set to Dynamic Host Configuration Protocol (DHCP).
LED Indicators Front panel • One two-color LED indicator for system status • Two single-color LED indicators for power and enclosure mode NOTE: The enclosure mode LED is not applicable to the PowerVault MD3200i series storage array.
Power Supplies AC power supply (per power supply) Wattage 600 W Voltage 100–240 VAC (8.6 A–4.3 A) Heat dissipation 100 W Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach a maximum of 55 A per power supply for 10 ms or less.
Environmental NOTE: For additional information about environmental measurements for specific system configurations, see www.dell.com/environmental_datasheets. Temperature Operating 10 °C to 35 °C (50 °F to 95 °F) with a maximum temperature gradation of 10 °C per hour NOTE: For altitudes above 2950 feet, the maximum operating temperature is derated 1ºF/550 ft.
Matrices de stockage Dell PowerVault MD3200i et MD3220i Guide de mise en route Séries E03J et E04J de modèle réglementaire
Remarques, précautions et avertissements REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : une PRÉCAUTION vous avertit d'un risque d'endommagement du matériel ou de perte de données en cas de non-respect des instructions. AVERTISSEMENT : un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessure corporelle ou de mort.
Avant de commencer REMARQUE : Dans ce document, les références à la matrice de stockage Dell PowerVault série MD3200i concernent les matrices de stockage Dell PowerVault MD3200i et Dell PowerVault MD3220i. Le boîtier d'extension Dell PowerVault MD1200 désigne les boîtiers Dell PowerVault MD1200 et Dell PowerVault MD1220.
Compléter la liste de vérification de l'interface iSCSI. Paramètres IPv4 A Clé secrète CHAP mutuelle serveur hôte 192.168.133.101 (ent. 3 par défaut) 192.168.128.101 (port du réseau de gestion) 192.168.132.101 (entrée 2 par défaut) 192.168.131.101 (ent. 1 par défaut) 192.168.130.101 (entrée 0 par défaut) B 192.168.130.102 (ent. 0 par défaut) 192.168.131.102 (entrée 1 par défaut) 192.168.132.102 (ent. 2 par défaut) 192.168.133.
B Passerelle par défaut Contrôleur iSCSI 0, Ent. 0 ___ ___ ___ ___ Masque de sous-réseau ___ ___ ___ ___ Contrôleur iSCSI 0, Ent. 1 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Contrôleur iSCSI 0, Ent. 2 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Contrôleur iSCSI 0, Ent. 3 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Port de gestion cntrl 0 ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ Contrôleur iSCSI 1, Ent.
• • Le Guide de programmation SMI-S fournit des informations sur l'utilisation du fournisseur MI-S et la programmation SMI-S. Tous les supports fournis avec le système contiennent de la documentation et des outils de configuration et de gestion du système, notamment du système d'exploitation même et du logiciel de gestion du système ; les supports contiennent également des mises à jour et les composants système que vous avez achetés avec le système.
Configurations courantes Câblage des hôtes reliés directement Serveur 1 Serveur 2 Serveur 3 Serveur 4 Matrice de stockage Réseau d'entreprise, public ou privé Guide de mise en route 27
Câblage des hôtes reliés au réseau SAN Serveur Commutateur 1 Commutateur 2 Matrice de stockage Réseau d'entreprise, public ou privé 28 Guide de mise en route
Jusqu'à 32 hôtes Serveur 1 Serveur 2 Commutateur 1 Commutateur 2 Matrice de stockage Réseau d'entreprise, public ou privé Guide de mise en route 29
Installation et configuration AVERTISSEMENT : avant d'exécuter la procédure ci-dessous, lisez les consignes de sécurité fournies avec le système. Déballage du système Déballez votre système et identifiez chaque élément en consultant la liste de composants livrée avec votre système. Installation des rails et du système dans un rack Assemblez les rails et installez le système dans le rack en suivant les consignes de sécurité et les instructions d'installation du rack fournies avec votre système.
Branchement du ou des câbles d'alimentation Avant de connecter les câbles d'alimentation, assurez-vous que le commutateur d'alimentation est en position OFF (ÉTEINT). Branchez le ou les câbles d'alimentation sur le système. Fixation du ou des câbles d'alimentation Fixez fermement les câbles au support de fixation à l'aide de la lanière fournie.
Câblage de votre boîtier d'extension Boîtier d'extension PowerVault série MD1200 2 (en option) Boîtier d'extension PowerVault série MD1200 1 (en option) Matrice de stockage PowerVault série MD3200i Mise sous tension du boîtier 32 Guide de mise en route
Mettez les composants sous tension dans l'ordre suivant 1 Commutateurs Ethernet (si utilisés). 2 Boîtiers d'extension PowerVault série MD1200 (si utilisés). REMARQUE : avant d'allumer la matrice de stockage, assurez-vous que le voyant d'état du boîtier d'extension est bleu. 3 Matrice de stockage PowerVault série MD3200i. REMARQUE : avant d'allumer le(s) serveur(s) hôte, assurez-vous que le voyant d'état de la matrice de stockage est bleu. 4 Serveur(s) hôte.
L'application MD Storage Manager configure, gère, et contrôle la matrice de stockage. L'utilitaire de configuration MD (MDCU) est un utilitaire optionnel qui permet une approche consolidée de la configuration des ports de gestion, des ports hôtes iSCSI et de la création de sessions pour les matrices de stockage sur disques modulaires iSCSI. Il vous est recommandé d'utiliser l'utilitaire MDCU pour configurer iSCSI sur chaque hôte connecté à la matrice de stockage.
REMARQUE : cette option ne s'applique qu'à l'installation du logiciel client Windows. 7 Confirmez l'emplacement de l'installation et cliquez sur Install (Installer). 8 À l'invitation (le cas échéant), redémarrez le serveur hôte après la fin de l'installation. 9 Lorsque le redémarrage est terminé, l'utilitaire MDCU peut se lancer automatiquement. S'il ne se lance pas automatiquement, lancez-le manuellement.
Identification du numéro de service Votre système est identifié par un code de service express et un numéro de service uniques. Le code de service express et le numéro de service se trouvent sur le devant et l'arrière du système à côté des modules de contrôleur RAID. Dell utilise ces informations pour acheminer les appels de support au technicien qui convient.
Caractéristiques techniques Lecteurs PowerVault MD3200i Jusqu'à 12 disques durs SAS remplaçables à chaud 3,5 pouces (3,0 Gb/s et 6,0 Gb/s) PowerVault MD3220i Jusqu'à 24 disques durs SAS remplaçables à chaud 2,5 pouces (3,0 Gb/s et 6,0 Gb/s) Modules de contrôleur RAID Modules de contrôleur RAID • Un ou deux modules remplaçables à chaud avec capteurs de température.
Extension PowerVault Série MD1200 Prend en charge jusqu'à 192 disques durs avec n'importe quelle combinaison de boîtiers d'extension PowerVault MD1200 ou PowerVault MD1220. La prise en charge de 192 disques durs est une fonction premium et doit être activée. Le nombre maximum de disques durs pris en charge sans utiliser la fonction premium est 120. La connectivité à chemin redondant fournit des chemins de données redondants à chaque disque dur.
Voyants (suite) Module de contrôleur RAID Dix voyants monochromes : • Un voyant de panne de batterie • Un voyant d'activité de la mémoire cache • Un voyant de panne du contrôleur • Un voyant d'état de l'alimentation de contrôleur • Un voyant système • Un voyant d'activité de gestion Ethernet • Quatre voyants d'activité de port d'entrée iSCSI Six voyants bichromes : • Quatre voyants de vitesse de lien d'entrée iSCSI • Un voyant de panne ou de lien de sortie SAS • Un voyant de vitesse de lien Ethernet de ges
Alimentation disponible pour les disques durs (par logement) PowerVault MD3200i 25 W PowerVault MD3220i 12 W Alimentation du module de contrôleur RAID (par emplacement) Consommation de courant maximale 100 W Caractéristiques physiques PowerVault MD3200i Hauteur 8,68 cm (3,41 pouces) Largeur 44,63 cm (17,57 pouces) Profondeur 60,20 cm (23,70 pouces) Poids (configuration maximale) 29,30 kg (64,6 livres) Poids (vide) 8,84 kg (19,5 livres) PowerVault MD3220i Hauteur 8,68 cm (3,41 pouces) Large
Environnement (suite) Humidité relative En fonctionnement De 20 à 80 % (sans condensation) avec un gradient d'humidité maximal de 10 % par heure Entreposage De 5 à 95 % (sans condensation) Tolérance maximale aux vibrations En fonctionnement 0,25 G avec un balayage de 3 à 200 Hz pendant 15 minutes Entreposage 0,5 G avec un balayage de 3 à 200 Hz pendant 15 minutes Choc maximal En fonctionnement Une impulsion de choc de 31 G pendant un maximum de 2,6 ms sur l'axe z positif (une impulsion de chaque cô
42 Guide de mise en route
Matrizes de armazenamento Dell PowerVault MD3200i e MD3220i Introdução ao uso do sistema Modelo de normalização séries E03J e E04J
Notas, Avisos e Advertências NOTA: uma NOTA fornece informações importantes para ajudar você a aproveitar melhor os recursos do computador. AVISO: um AVISO indica um potencial de danos ao hardware ou a perda de dados se as instruções não forem seguidas. ADVERTÊNCIA: uma ADVERTÊNCIA indica um potencial de danos à propriedade, risco de lesões corporais ou mesmo de risco de vida. ____________________ As informações contidas nesta publicação estão sujeitas a alterações sem aviso prévio. © 2011 Dell Inc.
Antes de começar NOTA: Neste documento, a matriz de armazenamento Dell PowerVault série MD3200i se refere tanto à matriz Dell PowerVault MD3200i quanto à matriz Dell PowerVault MD3220i. O gabinete de expansão Dell PowerVault série MD1200 se refere tanto ao Dell PowerVault MD1200 quanto ao Dell PowerVault MD1220.
Preencher a planilha iSCSI Configurações de IPv4 A Segredo CHAP mútuo servidor host 192.168.133.101 (em 3 por padrão) 192.168.128.101 (porta da rede de gerenciamento) 192.168.132.101 (em 2 por padrão) 192.168.131.101 (em 1 por padrão) 192.168.130.101 (em 0 por padrão) B 192.168.130.102 (em 0 por padrão) Matriz de armazenamento PowerVault série MD3200i Segredo CHAP do destino 192.168.131.102 (em 1 por padrão) 192.168.132.102 (em 2 por padrão) 192.168.133.102 (em 3 por padrão) 192.168.128.
B Endereço IP estático (matriz de armazenamento) controlador iSCSI 0, em 0 ___ . ___ . ___ . ___ Máscara de sub-rede Gateway padrão ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ controlador iSCSI 0, em 1 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ controlador iSCSI 0, em 2 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ controlador iSCSI 0, em 3 ___ . ___ . ___ . ___ controlador da porta de ___ . ___ . ___ .
• • O Guia do programador de SMI-S fornece informações sobre o uso do provedor de SMI-S e sobre a programação de SMI-S. As mídias fornecidas com o sistema que contêm documentação e ferramentas para a configuração e o gerenciamento do sistema, incluindo aquelas relacionadas ao sistema operacional, ao software de gerenciamento do sistema, a atualizações do sistema e a componentes adquiridos com o sistema. NOTA: Verifique sempre se há atualizações disponíveis no site support.dell.
Configurações comuns Cabeamento de hosts conectados diretamente Servidor 1 Servidor 2 Servidor 3 Servidor 4 Matriz de armazenamento Rede corporativa, pública ou privada Introdução ao Uso do Sistema 49
Cabeamento de hosts conectados à SAN Servidor Comutador 1 Comutador 2 Matriz de armazenamento Rede corporativa, pública ou privada 50 Introdução ao Uso do Sistema
Até 32 hosts Servidor 1 Servidor 2 Comutador 1 Comutador 2 Matriz de armazenamento Rede corporativa, pública ou privada Introdução ao Uso do Sistema 51
Instalação e configuração ADVERTÊNCIA: Antes de executar o procedimento abaixo, siga as instruções de segurança fornecidas com o sistema. Remover o sistema da embalagem Desembale o sistema e identifique cada item de acordo com a lista fornecida. Instalar os trilhos e o sistema no rack Monte os trilhos e instale o sistema no rack, seguindo as instruções de segurança e as instruções de instalação fornecidas com o sistema.
Conectar o(s) cabo(s) de alimentação Verifique se a chave está na posição “desligada” (OFF), antes de conectar os cabos de alimentação. Conecte o(s) cabos de alimentação ao sistema. Prender o(s) cabo(s) de alimentação Prenda firmemente os cabos ao gancho usando a tira fornecida.
Cabeamento do gabinete de expansão Gabinete de expansão PowerVault série MD1200 2 (opcional) Gabinete de expansão PowerVault série MD1200 1 (opcional) Matriz de armazenamento PowerVault série MD3200i Ligar o gabinete 54 Introdução ao Uso do Sistema
Ligue os componentes na seguinte ordem: 1 Comutadores Ethernet (se forem usados). 2 Gabinetes de expansão PowerVault série MD1200 (se estiverem sendo usados). NOTA: Antes de ligar a matriz de armazenamento, verifique se o LED de status do gabinete de expansão está azul. 3 Matriz de armazenamento PowerVault série MD3200i. NOTA: Antes de ligar o(s) servidor(es) host, verifique se o LED de status da matriz de armazenamento está azul. 4 Servidor(es) host. Instalar o bezel Instale o bezel (opcional).
O software MD Storage Manager (gerenciamento de armazenamento em discos modulares) configura, gerencia e monitora a matriz de armazenamento. O utilitário de configuração de MD (MDCU - MD Configuration Utility) é um utilitário opcional que faz abordagem consolidada para a configuração de portas de gerenciamento, portas de host iSCSI e para a criação de sessões das matrizes modulares de armazenamento em disco iSCSI.
NOTA: Esta opção só se aplica à instalação de software de cliente Windows. 7 Confirme o local de instalação e clique em Install. 8 Se for solicitado, reinicialize o servidor quando a instalação terminar. 9 Quando a reinicialização terminar, o MDCU será aberto automaticamente. Se o MDCU não for aberto automaticamente, abra-o manualmente. • Em sistemas operacionais baseados no Windows,clique em Iniciar→ Dell→ Modular Disk Configuration Utility.
Informações da norma NOM (apenas para o México) As informações a seguir são fornecidas sobre o dispositivo descrito neste documento em conformidade com os requisitos das normas oficiais mexicanas (NOM): Importador: Número do modelo: Tensão de alimentação: Frequência: Consumo de corrente: E03J e E04J 100 a 240 VCA 50/60 Hz 8,6 A Especificações técnicas Unidades PowerVault MD3200i Até 12 discos rígidos SAS de 3,5 polegadas (3,0 Gbps e 6,0 Gbps) com troca a quente (“hot swappable”) PowerVault MD3220i Até
Módulos controladores de RAID Módulos controladores de RAID • Um ou dois módulos de troca a quente (“hot swappable”) com sensores de temperatura • 2 GB de cache por controlador Conectores do painel traseiro (por módulo controlador de RAID) Conectores iSCSI Quatro conectores de entrada iSCSI de 1 GB para a conexão de hosts Conector de expansão SAS Uma porta de saída SAS (SAS OUT) para expansão com um gabinete PowerVault série MD1200 adicional. NOTA: Os conectores SAS são compatíveis com SFF-8088.
Expansão PowerVault série MD1200 Suporta um máximo de 192 discos rígidos com qualquer combinação de gabinetes de expansão PowerVault MD1200 ou PowerVault MD1220. O suporte para 192 discos rígidos é um recurso Premium e precisa ser ativado. O número máximo de discos rígidos suportados sem o uso de recursos Premium é 120. A conectividade de caminho redundante fornece caminhos redundantes de dados para cada disco rígido.
LEDs indicadores (continuação) Módulo controlador de RAID Dez LEDs de cor única: • Um para falha da bateria • Um para atividade de cache • Um para falha do controlador • Um para alimentação do controlador • Um para identificação do sistema • Um para atividade da Ethernet de gerenciamento • Quatro para atividade das portas de entrada iSCSI Seis LEDs de duas cores: • Quatro para velocidade do link de entrada iSCSI • Um para falha ou link de saída SAS • Um para velocidade do link Ethernet de gerenciamento Ch
Potência disponível para discos rígidos (por slot) PowerVault MD3200i 25 W PowerVault MD3220i 12 W Potência do módulo controlador de RAID (por slot) Consumo máximo de potência 100 W Características físicas PowerVault MD3200i Altura 8,68 cm Largura 44,63 cm Profundidade 60,20 cm Peso (com a configuração máxima) 29,30 kg Peso (em vazio) 8,84 kg PowerVault MD3220i Altura 8,68 cm Largura 44,63 cm Profundidade 54,90 cm Peso (com a configuração máxima) 24,22 kg Peso (em vazio) 8,61 kg Requ
Requisitos ambientais (continuação) De armazenamento -40°C a 65°C com variação máxima de temperatura de 20°C por hora Umidade relativa De operação 20% a 80% (sem condensação) com variação de umidade máxima de 10% por hora De armazenamento 5% a 95% (sem condensação) Vibração máxima De operação 0,25 g em 3 a 200 Hz por 15 minutos De armazenamento 0,5 g em 3 a 200 Hz por 15 minutos Choque máximo De operação Um pulso de choque no eixo z positivo (um pulso em cada lado do sistema) de 31 g por 2,6 ms n
64 Introdução ao Uso do Sistema
Matrices de almacenamiento Dell PowerVault MD3200i y MD3220i Introducción al sistema Modelo reglamentario, series E03J y E04J
Notas, precauciones y avisos NOTA: una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. PRECAUCIÓN: un mensaje de PRECAUCIÓN indica la posibilidad de que se produzcan daños en el hardware o haya pérdida de datos si no se siguen las instrucciones. AVISO: un mensaje de AVISO indica la posibilidad de que se produzcan daños materiales, lesiones personales e incluso la muerte.
Antes de comenzar NOTA: a lo largo del documento, la matriz de almacenamiento de la serie Dell PowerVault MD3200i hace referencia a Dell PowerVault MD3200i y Dell PowerVault MD3220i. El gabinete de expansión de la serie Dell PowerVault MD1200 hace referencia a Dell PowerVault MD1200 y Dell PowerVault MD1220.
Cómo completar la hoja de trabajo de iSCSI Configuración de IPv4 A Servidor host 192.168.133.101 (predet.: entrada 3) 192.168.128.101 (puerto de red de admin.) 192.168.132.101 (predet.: entrada 2) 192.168.131.101 (predet.: entrada 1) 192.168.130.101 (predet.: entrada 0) B 192.168.130.102 (predet.: entrada 0) 192.168.131.102 (predet.: entrada 1) 192.168.132.102 (predet.: entrada 2) 192.168.133.102 (predet.
Contrl. iSCSI 0, entrada 0 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ Puerta de enlace predeterminada ___ . ___ . ___ . ___ Contrl. iSCSI 1, entrada 0 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ Contrl. iSCSI 2, entrada 0 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ Contrl. iSCSI 3, entrada 0 ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ ___ . ___ . ___ . ___ Contrl.
• • En la SMI-S Programmer’s Guide (Guía de los programadores de SMI-S) se proporciona información acerca de cómo utilizar el proveedor y la programación de SMI-S. En los soportes suministrados con el sistema se incluyen documentación y herramientas para configurar y administrar el sistema, incluidas las del sistema operativo, el software de administración del sistema, las actualizaciones del sistema y los componentes del sistema que haya adquirido con el sistema.
Configuraciones comunes Cableado de los hosts de conexión directa Servidor 1 Servidor 2 Servidor 3 Servidor 4 Matriz de almacenamiento Red corporativa, pública o privada Introducción al sistema 71
Cableado de los hosts de conexión SAN Servidor Conmutador 1 Conmutador 2 Matriz de almacenamiento Red corporativa, pública o privada 72 Introducción al sistema
Máximo de 32 hosts Servidor 1 Servidor Conmutador 1 Conmutador 2 Matriz de almacenamiento Red corporativa, pública o privada Introducción al sistema 73
Instalación y configuración AVISO: antes de realizar el procedimiento siguiente, revise las instrucciones de seguridad incluidas con el sistema. Desembalaje del sistema Desembale el sistema e identifique cada parte de la lista de embalaje que se envió con el sistema. Instalación de los rieles y del sistema en un bastidor Ensamble los rieles e instale el sistema en el bastidor siguiendo las instrucciones de seguridad y de instalación del bastidor incluidas con el sistema.
Conexión de los cables de alimentación Asegúrese de que el conmutador de alimentación esté en la posición de APAGADO antes de conectar los cables de alimentación. Conecte los cables de alimentación del sistema al sistema. Fijación de los cables de alimentación Fije los cables al soporte con firmeza con la cinta proporcionada.
Cableado del gabinete de expansión Gabinete 2 de expansión de la serie PowerVault MD1200 (opcional) Gabinete 1 de expansión de la serie PowerVault MD1200 (opcional) Matriz de almacenamiento de la serie PowerVault MD3200i Encendido del gabinete 76 Introducción al sistema
Encienda los componentes en el orden siguiente: 1 Conmutadores Ethernet (si se utilizan). 2 Gabinetes de expansión de la serie PowerVault MD1200 (si se utilizan). NOTA: antes de encender la matriz de almacenamiento, asegúrese de que el LED de estado del gabinete de expansión está iluminado en azul. 3 Matriz de almacenamiento de la serie PowerVault MD3200i. NOTA: antes de encender los servidores host, asegúrese de que el LED de estado de la matriz de almacenamiento está iluminado en azul.
El software MD Storage Manager configura, administra y supervisa la matriz de almacenamiento. La MD Configuration Utility (MDCU) es una utilidad opcional que proporciona un enfoque consolidado para la configuración de puertos de administración y de host iSCSI, y de la creación de sesiones para las matrices de almacenamiento en disco modular iSCSI. Se recomienda utilizar MDCU para configurar iSCSI en cada uno de los servidores hosts conectados a la matriz de almacenamiento.
NOTA: esta opción se aplica solo para la instalación del software cliente de Windows. 7 Confirme la ubicación de la instalación y haga clic en Install (Instalar). 8 Si se le solicita, reinicie el servidor host después de completar la instalación. 9 Una vez terminado el reinicio, la MDCU puede iniciarse automáticamente. Si la MDCU no se inicia automáticamente, iníciela manualmente. • En un sistema operativo basado en Windows, haga clic en Inicio→ Dell→ Modular Disk Configuration Utility.
Información de la NOM (sólo para México) La información que se proporciona a continuación aparece en el dispositivo descrito en este documento en cumplimiento con los requisitos de la Norma Oficial Mexicana (NOM): Importador: Número de modelo: Voltaje de alimentación: Frecuencia: Consumo eléctrico: E03J y E04J 100-240 VCA 50 Hz/60 Hz 8,6 A Especificaciones técnicas Unidades PowerVault MD3200i Hasta doce unidades de disco duro de intercambio directo SAS de 3,5 pulgadas (3,0 Gbps y 6,0 Gbps) PowerVault M
Módulos de la controladora RAID Módulos de la controladora RAID • Uno o dos módulos de intercambio directo con sensores de temperatura • 2 GB de caché por controladora Conectores del panel posterior (por módulo de controladora RAID) Conectores iSCSI Cuatro conectores de entrada iSCSI de 1 GB para conectar hosts Conector de expansión SAS Un puerto de salida SAS para la expansión a un gabinete de la serie PowerVault MD1200 adicional NOTA: los conectores SAS son compatibles con SFF-8088.
Placa de plano posterior • 12 ó 24 conectores de unidad de disco duro SAS Conectores • Dos conectores para módulos de suministro de energía/ventilador de enfriamiento • Dos conjuntos de conectores del módulo de controladora RAID • Un conector del panel de control para LED anteriores y un conmutador de modo de alojamiento Sensores Dos sensores de temperatura Indicadores LED Panel anterior • Un indicador LED de dos colores para el estado del sistema • Dos indicadores LED de un solo color para la alimenta
Indicadores LED (continuación) Módulo de la controladora RAID Diez LEDs de un solo color: • Uno de batería defectuosa • Uno de caché activa • Uno de controladora defectuosa • Uno de alimentación de controladora • Uno de identificación del sistema • Uno de actividad Ethernet de administración • Cuatro de actividad del puerto de entrada iSCSI Seis LEDs de dos colores: • Cuatro de velocidad del enlace de entrada iSCSI • Uno de fallo o enlace de salida de SAS • Uno de velocidad del enlace Ethernet de administr
Suministros de energía Suministro de energía de CA (por suministro de energía) Potencia 600 W Voltaje 100–240 VCA (8,6 A–4,3 A) Disipación de calor 100 W Corriente de conexión máxima En condiciones normales de línea y en todo el rango operativo ambiente del sistema, la irrupción de corriente puede alcanzar un máximo de 55 A por cada suministro de energía durante 10 ms o menos Alimentación de la unidad de disco duro disponible (por ranura) PowerVault MD3200i 25 W PowerVault MD3220i 12 W Alimentac
Especificaciones medioambientales NOTA: para obtener información adicional acerca de medidas ambientales relativas a configuraciones del sistema específicas, vaya a www.dell.com/environmental_datasheets.
86 Introducción al sistema
Printed in the U.S.A. Imprimé aux U.S.A. Impresso nos EUA. Impreso en los EE.UU. w w w. d e l l . c o m | s u p p o r t . d e l l .
Printed in Brazil. Imprimé au Brésil. Impresso no Brasil. Impreso en Brasil. w w w. d e l l . c o m | s u p p o r t . d e l l .