Matrices de almacenamiento Dell PowerVault MD3600f y MD3620f Manual del propietario Modelo regulatorio: Serie E03J y Serie E04J Tipo regulatorio: E03J001 y E04J001
Notas, precauciones y avisos NOTA: una NOTA proporciona información importante que le ayudará a utilizar mejor el equipo. PRECAUCIÓN: un mensaje de PRECAUCIÓN indica la posibilidad de daños en el hardware o la pérdida de datos si no se siguen las instrucciones. AVISO: un mensaje de AVISO indica el riesgo de daños materiales, lesiones o incluso la muerte. ____________________ © 2013 Dell Inc.
Contenido 1 Introducción . . . . . . . . . . . . . . . . . . . . . . Acerca de este documento . . . . . . . . . . . . . . . 21 Contenido de la caja de la matriz de almacenamiento Dell PowerVault serie MD3600f . . . . . . . . . . . . . 22 Matriz de almacenamiento de la serie MD3600f. . . . . . . . . . . . . . . . . . . . . . . 22 Dell PowerVault Modular Disk Storage Manager . . . . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . . . . . . 23 Otra información útil .
3 Planificación: Módulos de la controladora RAID . . . . . . . . Módulos de la controladora RAID . . . . . . . . . . 35 . . . . . . . . . . . 35 Conectores y funciones del módulo de la controladora RAID . . . . . . . . . . . . . . . . . . . . Indicaciones de enlace/velocidad de LED de canal de host . . . . . . . . . . . . . . . . . . . . . . . . Módulo de la controladora RAID: funciones adicionales . . . . . . . . 38 . . . . . . . . . . . .
Tecnología de informes de análisis de autosupervisión (SMART) . . . . . . . Discos virtuales y grupos de discos 48 . . . . . . . . 48 . . . . . . . . . . . . . . 48 . . . . . . . . . . . . . . . . . . . . . 49 Estados de disco virtual Niveles de RAID . . . . . . Uso de nivel de RAID . Tamaño del segmento . . . . . . . . . . . . . . . 50 . . . . . . . . . . . . . . . . . . 51 Operaciones de disco virtual . . . . . . . . . . . . . . Inicialización de disco virtual . . . . . . . . . . .
Tipos de host . . . . . . . . . . . . . . . . . . . . Discos virtuales de instantánea . . . . . . . . . . Disco virtual de repositorio de instantánea Copia de disco virtual . 62 . . . . . . . . . . . . . . . 62 . . . . . . . . . . . Uso conjunto de instantánea y copia de disco . Software de múltiples rutas . 64 . . . . . . . . . . . . . . 64 . . . 65 . . . . . . . . . . . . . 66 . . . . . . . . . . . . . . . . . . .
Visualización de conexiones de la matriz de almacenamiento . . . . . . . . . . . . . . . . . 85 Cómo agregar/editar un comentario en una matriz de almacenamiento existente . . . . . . . . . . . 86 Cómo quitar matrices de almacenamiento . . . . . 86 . . . . . . . . 87 Habilitación de funciones Premium Pantalla de alerta de migración tras error . . . . . 87 Cambio de la configuración de caché en la matriz de almacenamiento . . . . . . . . . . . . . . . . .
Eliminación del acceso de host . . . . . . . . . . . . Administración de grupos de hosts . . . . . . . . . . Creación de un grupo de hosts . . . . . . . . . . Cómo mover un host a un grupo de hosts diferente . . . . . . . . . . . 104 105 . . . . . . . . . . . . . . . . 105 . 105 . . . . . . . . 106 Administración de identificadores de puerto de host 108 Protección de la ruta de datos de E/S . Configuración: Grupos de discos y discos virtuales . . . . . . . . . . . . . . . . .
Cómo guardar una clave de seguridad . Validar clave de seguridad . . . . . . . 129 . . . . . . . . . . . . 130 Desbloqueo de discos físicos de seguridad . . . . 131 . . . . . . . . 131 . . . . . . . . . . . 132 Borrado de discos físicos seguros . Configuración de discos físicos de repuesto dinámico . . . . . . . . . Repuesto dinámico y regeneración Repuestos dinámicos globales . . . . . . . . . 134 . . . . . . . . . . 134 Operación de repuesto dinámico. . . . . . . . . .
Particionamiento de almacenamiento . . . . . . . . Expansión de grupo de discos y discos virtuales . Expansión de grupo de discos . . 152 . . . . . . . . . . 152 . . . . . . . . . . . . 153 . . . . . . . . . . . . . 153 Expansión del disco virtual Uso de capacidad libre . 150 Uso de capacidad no configurada . . . . . . . . 153 Migración de grupo de discos . . . . . . . . . . . . . 154 Exportar grupo de discos . . . . . . . . . . . . . 154 Exportación de un grupo de discos .
Preparación de los servidores host para crear la instantánea mediante la ruta de acceso sencilla . . . . . . . . . . . . . . . . . . . 164 Creación de un disco virtual de instantánea mediante la ruta de acceso avanzada . . . . . . . . . . . . . . . 167 Acerca de la ruta de acceso avanzada . . . . . . 167 Preparación de los servidores host para crear l a instantánea mediante la ruta de acceso avanzada . . . . . . . . . . . . . . . . . .
11 Configuración: Función Premium Copia de disco virtual . . . . . . . . . . Tipos de copias de disco virtual . Copia fuera de línea . . . . . 185 . . . . . . . . . . . 186 . . . . . . . . . . . . . . . 187 . . . . . . . . . . . . . . . . . . 187 Creación de una copia de disco virtual para un disco compartido de MSCS. . . . . . . . . . . . . . . . . . 188 Permisos de lectura/escritura de disco virtual . . . . 189 . . . . . . . 190 . . . . . . . . 191 . . . . . . . . . . . . . . . .
Preparación de los servidores host para una nueva copia de un disco virtual . . . . . . . . . . . . . . 198 Cómo volver a copiar un disco virtual Quitar los pares de copia . . . . . . . 199 . . . . . . . . . . . . . . . . 200 12 Configuración: Función Premium Actualización a un nivel de alto rendimiento . . . . . . . . . . . . . . . . . . 201 13 Configuración: Función Premium Replicación remota . . . . . . . . . . . . . . . .
Sistemas de archivos transaccionales y la replicación remota . . . . . . . . . . . . . . . . 209 . . . . . . 210 Activación de la función Premium de replicación remota y creación de discos virtuales de replicación . . . . . . . . . . . . . . . . . . . 211 Activación y creación de discos virtuales de repositorio de replicación a partir de la matriz de almacenamiento . . . . . . . . . . . . . . . . 211 . . 212 . . . . . . . 213 Configuración y administración de la replicación remota . . . . . .
Resincronización automática de los discos virtuales . . . . . . . . . . . Resincronización manual de los discos virtuales . . . . . . . . . . . . . . . . . 227 . . . . . . . . . . 227 Inversión de funciones entre los discos virtuales primario y secundario . . . . . . . . . . . . . . . 227 . . . . . 228 . . . . . . 229 Promoción del disco virtual secundario o degradación del disco virtual primario . . Suspensión de una replicación remota Reanudación de una replicación remota.
Pasos de configuración de Device Mapper . . . 239 . . . . . . . . . 245 . . . . . . . . . . . . . . . . 246 Limitaciones y problemas conocidos Solución de problemas 15 Administración: Descargas de firmware . . . . . . . . . . . . . . . . . . . . . . 249 Descarga de los paquetes de la controladora RAID y de la NVSRAM . . . . . . . . . . . . . . . . . . . . . . . 249 Descarga del firmware de la controladora RAID y de la NVSRAM . . . . . . . . . . . . . . . . . . . . . . .
Extracción de una unidad de disco duro de relleno . . . . . . . . . . . . . . . . . . . . . . 263 Instalación de una unidad de disco duro de relleno . . . . . . . . . . . . . . . . . . . . . . 264 Extracción de una unidad de disco duro . . . . . . 264 Instalación de una unidad de disco duro. . . . . . 266 Extracción de una unidad de disco duro de un portaunidades de disco duro . . . . . . . . . . . . 267 Instalación de una unidad de disco duro en un portaunidades de disco duro . . . . . . . .
Extracción del panel de control . . . . . . . . . 279 Instalación del panel de control . . . . . . . . . 281 . . . . . . . . . . . . . . . . . . . . 282 Plano posterior . Extracción del plano posterior . . . . . . . . . . Instalación del plano posterior . 17 Administración: Inventario de firmware . . . . . . . . . . . . . . . . . . . . . 285 . . . . . . . . . . 287 Visualización del inventario de firmware . . . . . . . 287 . . . . . . . . . . 289 . . . . . . . . . . . . . . . .
Recovery Guru 301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 . . . . . . . . . . 304 . . . . . . . . . . . 304 . . . . . . . . . . . . . . . . . . . 305 Perfil de la matriz de almacenamiento Cómo ver las asociaciones lógicas . Cómo ver las asociaciones físicas Búsqueda de nodos Uso de la opción Ir a . Recuperación de una condición de matriz de almacenamiento que no responde . . . . . . Ubicación de un disco físico . . . . . 308 . . . . . . . . . . . . . .
Solución de problemas de las conexiones externas . 324 Solución de problemas del módulo de suministro de energía/ventilador de enfriamiento . . . . . . . . . . 325 Solución de problemas de enfriamiento de la matriz . . . . . . . . . . . . . . . . . . . . . . . . 326 Solución de problemas de los módulos de administración del gabinete de expansión . . . . . . 327 Solución de problemas de módulos de la controladora RAID . . . . . . . . . . . . . . . . . . . 328 . . . . . . .
Introducción NOTA: a menos que se especifique lo contrario, la serie MD3600f representa las matrices de almacenamiento Dell PowerVault MD3600f y Dell PowerVault MD3620f. AVISO: consulte el documento Información de seguridad, medioambiental y reglamentaria para obtener información importante sobre seguridad antes de seguir algún procedimiento que aparezca en este documento. Acerca de este documento Esta guía le familiariza con las funciones de la matriz de almacenamiento Dell PowerVault serie MD3600f.
Contenido de la caja de la matriz de almacenamiento Dell PowerVault serie MD3600f El paquete del producto serie MD3600f incluye: • Matriz de almacenamiento Dell PowerVault serie MD3600f • Transceptor conectable de formato reducido (SFP) (2 por controladora) • Cables de fibra óptica (opcional) • Cables de alimentación (2) • Bisel anterior (opcional) • Rieles de montaje (2) (opcional) • Soporte de recursos de la serie MD3600f • Instrucciones de instalación en bastidor • Introducción al sistem
Otra información útil AVISO: consulte la información sobre normativas y seguridad suministrada con el sistema. La información sobre la garantía puede estar incluida en este documento o constar en un documento aparte. • La Guía de introducción proporciona una visión general de la configuración y la conexión de cables de la matriz de almacenamiento. • La Guía de implementación proporciona instrucciones de instalación y configuración, tanto para software como para hardware.
Introducción
Planificación: Acerca de la matriz de almacenamiento Descripción general La matriz de almacenamiento serie MD3600f está diseñada para alta disponibilidad y ofrece acceso redundante al almacenamiento de datos. Ofrece compatibilidad para la configuración de la controladora RAID tanto única como dual. La matriz de almacenamiento Dell PowerVault serie MD3600f proporciona conectividad Fibre Channel (FC) al servidor host y permite el acceso a ocho servidores no redundantes o a cuatro servidores redundantes.
Funciones de hardware Componentes e indicadores del panel anterior Ilustración 2-1. Indicadores y funciones del panel anterior: Dell PowerVault MD3600f 1 2 3 4 5 6 Ilustración 2-2.
Ilustración 2-3. Indicadores y funciones del bisel anterior 1 2 3 Elemento Indicador, botón Icono Descripción o conector 1 LED de estado del gabinete El LED de estado del gabinete se ilumina cuando el gabinete está encendido. Está iluminado en azul durante el funcionamiento normal. Parpadea en azul cuando el servidor host está identificando el gabinete o cuando el botón de identificación del sistema está presionado. Está iluminado en ámbar cuando el gabinete se inicia o se restablece.
Elemento Indicador, botón Icono Descripción o conector 2 LED de alimentación El LED de alimentación se ilumina en verde cuando al menos un suministro de energía está dando energía al gabinete. 3 LED del modo dividido Este LED debería estar apagado cuando la función de modo dividido no es compatible con las matrices de almacenamiento serie MD3600f.
Indicadores y funciones del panel posterior Ilustración 2-4.
Pautas de los indicadores de la unidad de disco duro Ilustración 2-5.
Pauta de los indicadores de estado de la Condición unidad Apagado El disco físico: • no ha sido detectado todavía por el servidor host • se ha desactivado para su extracción • no es compatible con el módulo de la controladora RAID o no está en la ranura de disco físico NOTA: el indicador de estado de la unidad permanece apagado hasta que se inicializan todas las unidades de disco duro una vez que se enciende el sistema. Durante este tiempo, las unidades no están listas para la inserción ni la extracción.
Componentes del suministro de energía y del ventilador de enfriamiento La matriz de almacenamiento serie MD3600f incluye dos módulos de suministro de energía/ventilador de enfriamiento integrados de intercambio directo. Es preciso instalar ambos módulos para garantizar una refrigeración adecuada. El sistema requiere al menos que funcione uno de los ventiladores de enfriamiento para evitar que se caliente excesivamente.
Elemento Tipo de LED 1 Alimentación de CC Icono Descripción El LED parpadea en verde cuando el voltaje de salida de CC se encuentra dentro del límite. Si este LED está apagado, eso indica que el voltaje de salida de CC no se encuentra dentro del límite. 2 Fallo del suministro de energía/ventilador de enfriamiento El LED se ilumina en ámbar cuando el voltaje de salida de CC no se encuentra dentro del límite o se ha detectado un fallo en el ventilador.
Planificación: Acerca de la matriz de almacenamiento
Planificación: Módulos de la controladora RAID Módulos de la controladora RAID Los módulos de la controladora RAID proporcionan alto rendimiento, administración de subsistema de disco con tolerancia a errores y configuración de discos virtuales avanzada.Cada módulo de la controladora RAID contiene una caché duplicada de 2 GB o 4 GB para alta disponibilidad y está protegido por un mecanismo de descarga de caché alimentado por la batería. NOTA: La caché duplicada de 4 GB es una característica opcional.
Para obtener información sobre la conexión de cables, consulte la MD3600f and MD3620f Series Storage Array’s Deployment Guide (Guía de implementación de la matriz de almacenamiento serie MD3600f y MD3620f) en dell.com/support/manuals. Conectores y funciones del módulo de la controladora RAID Ilustración 3-1.
Elemento Componente Función 7 Puerto de depuración Únicamente soporte Dell. 8 LED de actividad de puerto de administración Se ilumina en verde cuando la conexión Ethernet está activa. 9 Conector Ethernet de puerto de administración Proporciona una conexión Ethernet de 100/1000 Mbps para la administración fuera de banda del gabinete. 10 LED de velocidad de Se ilumina en verde cuando la conexión Ethernet puerto de funciona a 1000 Mbps.
Elemento Componente Función 15 LED 1 / LED 0 de puerto FCIN 2 Muestra la velocidad de enlace y el estado del puerto según la tabla de enlace/velocidad del LED de canal de host que lo acompaña. 16 LED de identificación del sistema Parpadea en azul cuando se presiona el botón de encendido del conmutador de identificación del sistema en el panel anterior del gabinete. 17 LED de fallo de la controladora Se ilumina en ámbar cuando se detecta un fallo en la controladora.
Tabla 3-1. Indicadores de estado LED LED 1 LED 0 Velocidad habitual Apagado Apagado Enlace apagado Apagado On 2 Gbps Encendido Apagado 4 Gbps Encendido On 8 Gbps Módulo de la controladora RAID: funciones adicionales Unidad de reserva de la batería Cada controladora RAID contiene una unidad de reserva de la batería (BBU) de nanopolímeros de iones de litio de dos celdas.
Tabla 3-2. Tipo de umbral de apagado Superación de la temperatura del umbral Descripción del evento Umbral de fallo nominal Se ha establecido un evento crítico. Umbral de fallo máximo El apagado de los suministros de energía del sistema se produce en 3 minutos Umbral de apagado El apagado de los suministros de energía del sistema se produce en 5 segundos. Restablecimiento de la contraseña del sistema La contraseña de la matriz de almacenamiento se puede restablecer si se ha olvidado.
Caché de escritura diferida En la caché de escritura diferida, las operaciones de escritura hacen que se envíe una señal de finalización al sistema operativo host en cuanto la caché recibe los datos que se vayan a escribir. El disco físico de destino recibe los datos en un momento más adecuado para aumentar el rendimiento de la controladora.
Ilustración 3-2. Conexión de cable de fibra óptica 1 2 1 Transceptor SFP 2 Cable de fibra óptica Los puertos de expansión RAID admiten conexiones de expansión SAS. La Ilustración 3-3 muestra un cable SAS y un conector SFF-8088. Ilustración 3-3.
Interoperabilidad de dispositivos de 2 Gbps, 4 Gbps y 8 Gbps El estándar FC especifica un procedimiento de autodetección rápida. Si un puerto de 4 Gbps de un conmutador o dispositivo está conectado a un puerto de 2 Gbps, deberá negociarse que el enlace se ejecute a 2 Gbps. Si hay dos puertos de 8 Gbps en algún extremo de un enlace, la negociación ejecutará el enlace a 8 Gbps si éste admite las especificaciones necesarias.
Planificación: Módulos de la controladora RAID
Planificación: Términos y conceptos de la matriz de almacenamiento serie MD3600f En este capítulo se explican los términos y conceptos utilizados para la configuración y el funcionamiento de las matrices de almacenamiento serie MD3600f. Discos físicos, discos virtuales y grupos de discos Los discos físicos de la matriz de almacenamiento proporcionan la capacidad física de almacenamiento para sus datos.
Discos físicos En la matriz de almacenamiento solo se admiten discos físicos SAS de 6,0 Gbps compatibles con Dell. Si la matriz de almacenamiento detecta discos físicos no compatibles, marca el disco como no compatible y el disco físico se vuelve no disponible para todas las operaciones. NOTA: la matriz de almacenamiento serie MD3600f debe contener al menos dos discos físicos para funcionar correctamente. Esto es necesario porque los discos físicos se utilizan para almacenar información de configuración.
Tabla 4-1. Estado Estados de disco físico de la controladora RAID (continuación) Modo Descripción LED de estado del disco físico Reemplazado Asignado El disco físico de la ranura indicada se ha reemplazado y está listo para configurarse, o se está configurando de forma activa en un grupo de discos.
Tecnología de informes de análisis de autosupervisión (SMART) SMART supervisa el rendimiento interno de todos los componentes de disco físico para detectar fallos que indiquen un potencial de fallo en disco físico. SMART utiliza esta información para notificar si el fallo es inminente, de modo que un disco físico se pueda sustituir antes de que se produzca el fallo. La matriz de almacenamiento supervisa todas las unidades conectadas y le notifica si un disco físico informa de un fallo previsto.
Tabla 4-2. Estado Estados de disco virtual de la controladora RAID Descripción Fuera de línea Un disco virtual con uno o más discos miembros se encuentra en un estado inaccesible (ha fallado, faltante o está fuera de línea). Los datos del disco virtual ya no son accesibles. Forzar en línea La matriz de almacenamiento fuerza un disco virtual que está en un estado Fuera de línea a un estado Óptimo.
Uso de nivel de RAID Para garantizar el mejor rendimiento, debe seleccionar un nivel de RAID óptimo al crear un disco físico del sistema.
RAID 5 RAID 5 utiliza los datos de paridad y división de datos en bloques en todos los discos físicos (paridad distribuida) con la finalidad de proporcionar un elevado rendimiento de datos así como redundancia de éstos, en especial para pequeños accesos aleatorios.
El tamaño de segmento o tamaño de elemento de banda especifica el tamaño de los datos de una banda escritos en un único disco. La matriz serie MD3600f admite tamaños de elementos de banda de 8 KB, 16 KB, 32 KB, 64 KB, 128 KB, 256 KB y 512 KB. El tamaño de elemento de banda predeterminado es 128 KB. El ancho de banda, o la profundidad, hacen referencia al número de discos implicados en una matriz en la que se implemente la división de datos en bloques.
Comprobación de coherencia Una comprobación de coherencia verifica la exactitud de los datos en una matriz redundante (niveles de RAID 1, 5, 6 y 10). Por ejemplo, en un sistema con paridad, la comprobación de coherencia implica calcular los datos de un disco físico y comparar los resultados con el contenido del disco físico de paridad. Una comprobación de coherencia es parecida a una inicialización en segundo plano.
La matriz de almacenamiento realiza un seguimiento del ciclo de cada grupo de discos con independencia de los otros grupos de discos de la controladora y crea un punto de control. Si la operación de verificación de soporte de un grupo de discos se adelanta o es bloqueada por otra operación del grupo de discos, la matriz de almacenamiento se reanudará después del ciclo actual.
Migración de tamaño de segmento El tamaño de segmento hace referencia a la cantidad de datos (en KB) que la matriz de almacenamiento escribe en un único disco físico de un disco virtual antes de escribir datos en el siguiente disco físico. Los valores válidos para el tamaño de segmento son 8 KB, 16 KB, 32 KB, 64 KB, 128 KB, 256 KB y 512 KB. La migración dinámica de tamaño de segmento permite cambiar el tamaño de segmento de un determinado disco virtual.
Expansión de grupo de discos Como la matriz de almacenamiento admite discos físicos de conexión en caliente, puede agregar dos discos físicos simultáneamente para cada grupo de discos mientras la matriz de almacenamiento permanece en línea. Podrá acceder a los datos de los grupos de discos virtuales, discos virtuales y discos físicos durante la operación. Los datos y el espacio libre no utilizado aumentado se distribuirán dinámicamente por el grupo de discos.
Prioridad de operaciones en segundo plano de RAID La matriz de almacenamiento admite una prioridad configurable común para las siguientes operaciones de RAID: • Inicialización en segundo plano • Recreación • Copia de respaldo • Expansión de capacidad de disco virtual • Migración de nivel de RAID • Migración de tamaño de segmento • Expansión de grupo de discos • Desfragmentación de grupo de discos La prioridad de cada una de estas operaciones se puede cambiar para satisfacer los requisitos de
Migración de discos Puede mover discos virtuales de una matriz a otra sin poner la matriz de destino fuera de línea. Sin embargo, el grupo de discos que se esté migrando debe estar fuera de línea antes de realizar la migración del disco. Si el grupo de discos no está fuera de línea antes de la migración, la matriz de origen que contenga los discos físicos y virtuales dentro del grupo de discos los marcará como faltantes. Sin embargo, los propios grupos de discos migrarán a la matriz de destino.
Al intentar llevar a cabo la migración de disco virtual, siga estas recomendaciones: • Mover discos físicos a la matriz de destino para migración: al insertar unidades en la matriz de almacenamiento de destino durante la migración de disco virtual activa, espere a que aparezca el disco físico insertado en MDSM antes de insertar el siguiente disco físico.
Itinerancia de discos Puede mover los discos físicos dentro de una matriz. El módulo de la controladora RAID reconoce automáticamente los discos físicos reubicados y los coloca de forma lógica en los discos virtuales correspondientes que forman parte del grupo de discos. La itinerancia de disco se permite cuando el módulo de la controladora RAID está en línea o apagado. NOTA: el grupo de discos debe exportarse antes de mover los discos físicos.
Tipos de host Un servidor host es un servidor que accede a una matriz de almacenamiento. Los servidores host se asignan a los discos virtuales. Los servidores host tienen los atributos siguientes: • Nombre de host: nombre que identifica el host de forma exclusiva. • Grupo de hosts (sólo utilizado en soluciones de clúster): dos o más servidores host asociados juntos para compartir acceso a los mismos discos virtuales. Este grupo de hosts es una entidad lógica que puede crear en MDSM.
Disco virtual de repositorio de instantánea Al crear un disco virtual de instantánea, éste crea automáticamente un disco virtual de repositorio de instantánea. Un repositorio de instantánea es un disco virtual creado en la matriz de almacenamiento como recurso para un disco virtual de instantánea. Un disco virtual de repositorio de instantánea contiene metadatos de disco virtual de instantánea y datos de copia al escribir de un determinado disco virtual de instantánea.
La copia de disco virtual genera una copia completa de los datos del disco virtual de origen al disco virtual de destino en una matriz de almacenamiento y se puede realizar tanto en línea como fuera de línea. Disco virtual de origen Al crear una copia de disco virtual, se crea un par de copia con un disco virtual de origen y un disco virtual de destino en la misma matriz de almacenamiento.
Asegúrese de registrar el LUN utilizado para proporcionar acceso al disco virtual de origen. Esta información es necesaria cuando se define una asignación de servidor host a disco virtual para el disco virtual (de copia de seguridad) de destino. Igualmente, asegúrese de detener toda actividad de E/S del disco virtual de origen antes de iniciar el procedimiento de recuperación de disco virtual.
El software multirruta identifica la existencia de múltiples rutas a un disco virtual y establece una ruta preferente a ese disco. Si falla un componente de la ruta preferente, el software de multirruta redirecciona automáticamente las peticiones de E/S a la ruta alternativa para que la matriz de almacenamiento pueda seguir funcionando sin ninguna interrupción. NOTA: el software multirruta está disponible en el soporte de recursos de la serie MD3600f.
Propiedad de disco virtual MDSM se puede utilizar para crear y ver automáticamente discos virtuales. Utiliza la configuración óptima para dividir en bloques los datos del grupo de discos. Cuando se crean, los discos virtuales se asignan a módulos de la controladora RAID alternativos. Esta asignación predeterminada ofrece un medio sencillo de equilibrar la carga de trabajo de los módulos de la controladora RAID.
• Profundidad de cola mínima con subconjunto: la directiva de profundidad de cola mínima con subconjunto también se conoce como directiva de E/S mínima o de solicitudes mínimas. Esta directiva dirige la siguiente solicitud de E/S a la ruta de datos que tenga menos solicitudes de E/S pendientes a la cola. Para esta directiva, una solicitud de E/S no es más que un comando a la cola. El tipo de comando o el número de bloques asociados con el comando no se tienen en cuenta.
• Si la matriz de almacenamiento que está supervisando se inicia o pasa al estado No responde, aparecerá un cuadro de diálogo informativo. El cuadro de diálogo le indicará que el Supervisor de rendimiento no puede sondear la matriz de almacenamiento en busca de datos de rendimiento. Para supervisar el rendimiento de las matrices: 1 Abra MDSM y seleccione la matriz de almacenamiento adecuada. 2 Abra la Ventana Administración de matrices (AMW) de la matriz de almacenamiento seleccionada.
8 Haga clic en Guardar como en el cuadro de diálogo principal del Supervisor de rendimiento para guardar las estadísticas de rendimiento actualmente visualizadas. 9 Seleccione el directorio adecuado. 10 Escriba un nombre de archivo en el cuadro de texto Nombre de archivo. NOTA: la extensión .perf es el valor predeterminado. 11 Seleccione un tipo de archivo de la lista Tipos de archivo.
Tabla 4-3. Descripción de la tabla del Supervisor de rendimiento Encabezados de columna Descripción E/S por segundo actuales Instantánea de E/S por segundo (ESP = Entrada/salida por segundo o una transacción de E/S finalizada). E/S por segundo máximas Máximo de E/S por segundo registradas desde el último inicio de tiempo. Para obtener más información, consulte la Matriz de compatibilidad MD PowerVault en dell.com/support/manuals.
Configuración: Descripción general La ayuda en línea de Dell PowerVault Modular Disk Storage Manager (MDSM) contiene información sobre cómo utilizar la aplicación MDSM para realizar las tareas de configuración y administración descritas en este documento. Puede acceder a la ayuda en línea seleccionando Ayuda, que se encuentra en la esquina superior derecha de la interfaz de MDSM.
• Debajo de la barra de herramientas están las fichas. Las fichas se utilizan para agrupar las tareas que puede realizar en una matriz de almacenamiento. • Debajo de las fichas está la barra de estado. La barra de estado muestra los mensajes de estado y los iconos de estado relacionados con la matriz de almacenamiento. NOTA: de forma predeterminada, la barra de herramientas y la barra de estado no aparecen.
• Agregar comentarios sobre la matriz de almacenamiento a la Vista tabla. • Ordenar las filas de la Vista tabla en función de diferentes criterios. • Almacenar los datos de configuración y las preferencias de vista de la EMW en archivos de configuración local. La próxima vez que abra la EMW, los datos de los archivos de configuración local se utilizarán para mostrar preferencias y vistas personalizadas.
Ventana Administración de matrices Puede iniciar la AMW desde la EMW. La AMW proporciona funciones de administración para una única matriz de almacenamiento. Puede tener varias AMW abiertas simultáneamente para administrar diversas matrices de almacenamiento. Para iniciar la AMW: 1 En la EMW, en la ficha Dispositivos, haga doble clic en la matriz de almacenamiento correspondiente. Se muestra el menú contextual del almacenamiento seleccionado.
• Soporte: puede completar tareas de soporte comunes, como descargar firmware de módulo de la controladora RAID, ver la ayuda en línea, etc. En la AMW, puede: • Proporcionar opciones de matriz de almacenamiento como, por ejemplo, cambiar el nombre de una matriz de almacenamiento, cambiar una contraseña o habilitar una exploración de soportes en segundo plano.
Configuración: Descripción general
Configuración: Acerca de la matriz de almacenamiento Existen dos formas de administrar una matriz de almacenamiento: • Administración fuera de banda • Administración en banda Administración fuera de banda Al utilizar el método de administración fuera de banda, los datos son independientes de comandos y eventos. Los datos se transmiten a través de la interfaz del host a la controladora, mientras que los comandos y los eventos se transmiten a través de cables Ethernet de los puertos de administración.
Administración en banda Al utilizar la administración en banda, los comandos, los eventos y los datos se transmiten a través de la interfaz del host a la controladora. A diferencia de lo que sucede con la administración fuera de banda, los comandos y los eventos se combinan con los datos. NOTA: para obtener información detallada sobre la configuración de la administración en banda y fuera de banda, consulte la Guía de implementación.
Cómo agregar matrices de almacenamiento Puede agregar matrices de almacenamiento sólo en la EMW. Puede: • Detectar automáticamente matrices de almacenamiento • Agregar manualmente matrices de almacenamiento NOTA: verifique que la configuración de red del host o de la estación de administración, incluidas la dirección IP de la estación, la máscara de subred y la puerta de enlace predeterminada, sea correcta antes de agregar una nueva matriz de almacenamiento mediante la opción Automática.
Para agregar una matriz de almacenamiento en banda, agregue el host a través del cual la matriz de almacenamiento esté conectada a la red. NOTA: MDSM puede tardar varios minutos en conectarse a la matriz de almacenamiento especificada . Para agregar una matriz de almacenamiento manualmente: 1 Seleccione Editar→ Agregar matriz de almacenamiento.
Utilice la lista de tareas de configuración inicial la primera vez que configure una matriz de almacenamiento para llevar a cabo las tareas siguientes: • Localizar la matriz de almacenamiento: busque la ubicación física de la matriz de almacenamiento en la red activando los LEDs de identificación de la unidad. La matriz de almacenamiento puede identificarse con una etiqueta. • Asignar un nombre nuevo a la matriz de almacenamiento: utilice un nombre exclusivo que identifique cada matriz de almacenamiento.
• Ver y habilitar funciones avanzadas: MDSM puede incluir funciones avanzadas. Vea las funciones avanzadas que están disponibles y las funciones avanzadas que ya se hayan iniciado. Puede iniciar las funciones avanzadas disponibles que actualmente estén detenidas. Localización de matrices de almacenamiento Puede utilizar la opción Hacer parpadear para localizar e identificar físicamente una matriz de almacenamiento.
Para cambiar el nombre de una matriz de almacenamiento seleccionada: 1 Realice una de estas acciones: • En la ficha Configuración de la AMW, seleccione Cambiar el nombre de la matriz de almacenamiento. • En la vista Árbol de la ficha Dispositivos de la EMW, seleccione Editar→ Cambiar nombre. • En la vista Tabla de la ficha Dispositivos de la EMW, seleccione Editar→ Cambiar nombre.
Cómo definir una contraseña Puede configurar cada matriz de almacenamiento con una contraseña para evitar un acceso no autorizado. MDSM solicita la contraseña cuando se intenta cambiar la configuración de la matriz de almacenamiento, por ejemplo, al crear o eliminar un disco virtual. Las operaciones de vista no cambian la configuración de la matriz de almacenamiento y no requieren una contraseña. Puede crear una nueva contraseña o cambiar una existente.
Pautas para las contraseñas Al crear una contraseña, siga estas pautas: • Utilice contraseñas seguras para la matriz de almacenamiento. Una contraseña debe ser fácil de recordar, pero difícil de adivinar para los demás. Pruebe utilizar números o caracteres especiales en lugar de letras; por ejemplo, el número 1 en vez de la letra I o el símbolo @ en vez de la letra a. • Para obtener una mayor protección, utilice una contraseña larga, de al menos 15 caracteres alfanuméricos.
Cómo agregar/editar un comentario en una matriz de almacenamiento existente Un comentario descriptivo, con un nombre de matriz de almacenamiento correspondiente, es una herramienta de identificación útil. Puede agregar o editar un comentario para una matriz de almacenamiento sólo en la EMW. Para agregar o editar un comentario: 1 En la EMW, seleccione la ficha Dispositivos y seleccione la matriz de almacenamiento administrada correspondiente. 2 Seleccione Editar→ Comentario.
3 Para quitar la matriz de almacenamiento, haga clic en Sí. Habilitación de funciones Premium Puede habilitar las funciones Premium de la matriz de almacenamiento. Para habilitar las funciones Premium, debe obtener un archivo de clave de función específico para la función Premium que desee habilitar de su proveedor de almacenamiento. Para habilitar funciones Premium: 1 En la barra de herramientas de la AMW, seleccione Matriz de almacenamiento→ Funciones Premium.
Cambio de la configuración de caché en la matriz de almacenamiento 1 En la AMW, seleccione Matriz de almacenamiento→ Cambiar→ Configuración de caché. Aparecerá la ventana Cambiar configuración de caché. 2 Seleccione o especifique el porcentaje de datos no grabados en la caché para desencadenar un vaciado de la caché en Iniciar vaciado. 3 Seleccione o especifique el porcentaje de datos no grabados en la caché para detener un vaciado de la caché en curso en Detener vaciado.
Cómo cambiar el orden de gabinetes en el panel Físico Puede cambiar el orden de los módulos de la controladora RAID y los gabinetes de expansión en el panel Físico para que coincida con la configuración de hardware de la matriz de almacenamiento. El panel Físico que se muestra inicialmente es una vista predeterminada que puede no coincidir con su matriz de almacenamiento. El cambio de orden de gabinetes permanece en vigor hasta que se modifique de nuevo.
4 Haga clic en Aceptar. Aparecerá el cuadro de diálogo Configurar alertas. Para configurar alertas de correo electrónico, ver “Configuración de alertas de correo electrónico” en la página 90. Para configurar alertas de SNMP, ver “Configuración de alertas SNMP” en la página 93. Para configurar notificaciones de alerta para una única matriz de almacenamiento: 1 En la EMW, seleccione la ficha Dispositivos.
Se producen estos resultados, dependiendo de la selección: • Si ha seleccionado todas las matrices de almacenamiento, aparecerá el cuadro de diálogo Configurar alertas. • Si ha seleccionado una matriz de almacenamiento individual, aparecerá el cuadro de diálogo Seleccionar matriz de almacenamiento. Seleccione la matriz de almacenamiento para la que desea recibir alertas de correo electrónico y haga clic en Aceptar. Aparecerá el cuadro de diálogo Configurar alertas.
• Reemplazar una dirección de correo electrónico: en el área Direcciones de correo electrónico configuradas, seleccione la dirección de correo electrónico que vaya a reemplazar, escriba la dirección de correo electrónico de reemplazo en Dirección de correo electrónico y haga clic en Reemplazar. • Eliminar una dirección de correo electrónico: en el área Direcciones de correo electrónico configuradas, seleccione la dirección de correo electrónico y haga clic en Eliminar.
10 Haga clic en Aceptar. Aparece un icono de alerta junto a cada nodo de la vista Árbol donde se haya establecido una alerta. Para asegurarse de que el correo electrónico se envía correctamente: • Debe proporcionar un nombre de servidor de correo SMTP y una dirección de remitente de correo electrónico para que las direcciones de correo electrónico funcionen. • Las direcciones de correo electrónico que haya configurado previamente aparecerán en el área Direcciones de correo electrónico configuradas.
Se producen estos resultados, dependiendo de la selección: • • Si ha seleccionado todas las matrices de almacenamiento, aparecerá el cuadro de diálogo Configurar alertas. Si ha seleccionado una matriz de almacenamiento individual, aparecerá el cuadro de diálogo Seleccionar matriz de almacenamiento. Seleccione la matriz de almacenamiento para la que desea recibir notificaciones de alertas y haga clic en Aceptar. Aparecerá el cuadro de diálogo Configurar alertas.
Siga estas pautas para alertas SNMP: • Las direcciones SNMP que haya configurado previamente aparecerán en el área Direcciones SNMP configuradas. • El Nombre de comunidad SNMP viene determinado por el administrador del sistema y se configura dentro de una aplicación de administración como, por ejemplo, Dell Management Console. Dispone de más información sobre Dell Management Console en dell.com. • Puede configurar varias direcciones SNMP antes de hacer clic en Aceptar.
Para cambiar la configuración de batería, siga estos pasos: 1 En la AMW, seleccione Matriz de almacenamiento→ Cambiar→ Configuración de batería. Aparecerá el cuadro de diálogo Configuración de batería. 2 En Ubicación de la batería, seleccione una batería. 3 Compruebe estos detalles sobre la batería: • Estado de la batería • Vida útil de la batería • Días hasta la sustitución Para obtener más información, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager.
Configuración: Event Monitor Dell PowerVault Modular Disk Storage Manager (MDSM) incluye un Event Monitor. Event Monitor se ejecuta de forma continua en segundo plano y supervisa la actividad de las matrices de almacenamiento administradas. Si Event Monitor detecta algún problema crítico, puede notificarlo a un host o a un sistema remoto a través del correo electrónico, de mensajes de captura del Protocolo simple de administración de red (SNMP), o de ambos sistemas.
Cómo habilitar o deshabilitar Event Monitor Puede habilitar o deshabilitar Event Monitor en cualquier momento. Desactive Event Monitor si no desea que el sistema envíe notificaciones de alerta. Si está ejecutando Event Monitor en varios sistemas, al desactivarlo en todos los sistemas excepto en uno evitará que se envíen mensajes duplicados. NOTA: es recomendable que configure Event Monitor para que se inicie de forma predeterminada en una estación de administración que se ejecute las 24 horas del día.
Configuración: Acerca del host Configuración del acceso de host El software Modular Disk Storage Manager (MDSM) de Dell PowerVault se compone de varios módulos. Uno de estos módulos es el agente de contexto de host. El agente de host se instala como parte de la instalación de MDSM y se ejecuta continuamente en segundo plano.
La topología de host se puede volver a configurar. El usuario puede realizar las siguientes tareas: • Crear un host y asignarle un alias o etiqueta de usuario. • Agregar o asociar un nuevo identificador de puerto de host a un host particular. • Cambiar el alias o la etiqueta de usuario del identificador de puerto de host. • Mover o asociar un identificador de puerto de host con un host diferente. • Sustituir un identificador de puerto de host por un nuevo identificador de puerto de host.
Para definir un host: 1 En la AMW, seleccione la ficha Asignaciones y seleccione la matriz de almacenamiento correspondiente. 2 Realice una de las siguientes acciones: • Seleccione Asignaciones→ Definir→ Host. • Seleccione la ficha Configuracióny haga clic en Definir hosts manualmente. • Seleccione la ficha Asignaciones.
7 En tipo de Host, seleccione el sistema operativo adecuado para el host. Aparecerá la ventana Pregunta de grupo de host. 8 En esta ventana, puede seleccionar: • Sí: este host comparte acceso a los mismos discos virtuales con otros hosts. • No: este host NO comparte acceso a los mismos discos virtuales con otros hosts. 9 Haga clic en Siguiente. Si selecciona Sí, aparecerá la ventana Especificar grupo de hosts. Si selecciona No, ver paso 11.
Administración de grupos de hosts Un grupo de hosts es una entidad lógica formada por dos o más hosts que comparten el acceso a determinados discos virtuales de la matriz de almacenamiento. Los grupos de hosts se crean con MDSM. Todos los hosts de un grupo deben tener el mismo tipo de host (sistema operativo).
Cómo agregar un host a un grupo de hosts Puede agregar un host a un grupo de hosts existente o a un nuevo grupo de hosts mediante el Asistente para definir host. Para obtener más información, consulte “Definición de un host” en la página 100. También puede mover un host a un grupo de hosts diferente. Para obtener más información, consulte “Cómo mover un host a un grupo de hosts diferente” en la página 104.
Eliminación de un grupo de hosts 1 En la AMW, seleccione la ficha Asignaciones, seleccione el nodo del host en el panel Topología. 2 Realice una de estas acciones: • Seleccione Asignaciones→ Quitar. • Haga clic con el botón derecho del mouse en el nodo del host y seleccione Quitar en el menú emergente. Aparece el cuadro de diálogo Quitar. 3 Haga clic en Sí. El grupo de hosts seleccionado se quita.
Deberá detener y reiniciar el agente de host para ver los cambios realizados en la topología de host si: • Se conecta una nueva matriz de almacenamiento al servidor host. • Se añade un host mientras se encienden los módulos de controladora RAID. Linux Para iniciar o detener el agente de contexto de host, introduzca el comando siguiente en el indicador: SMagent start SMagent stop Detiene y luego reinicia SMagent después de: • Desconectar o sustituir una controladora.
NOTA: consulte la Guía de implementación para obtener más información sobre configuraciones de cables en dell.com/support/manuals. NOTA: para obtener la máxima redundancia, debe seleccionar todas las conexiones de host a la matriz cuando defina manualmente la topología de host. Por ejemplo, en un host pueden aparecer dos conexiones de host al configurar manualmente el acceso de host.
Administración de identificadores de puerto de host Puede administrar los identificadores de puerto de host que se agregan a la matriz de almacenamiento. Puede: • Agregar: agregar o asociar un nuevo identificador de puerto de host a un host particular. • Editar: cambiar el alias o la etiqueta de usuario del identificador de puerto de host. Puede mover (asociar) el identificador de puerto de host a un nuevo host.
3 Si agrega un nuevo identificador de puerto de host, vaya al paso 4. Si administra un identificador de puerto de host existente, vaya al paso 8. 4 Haga clic en Agregar. Aparece el cuadro de diálogo Agregar identificador de puerto de host. 5 Seleccione el método para agregar un identificador de puerto de host al host.
• Para quitar el identificador de puerto de host: seleccione el identificador de puerto de host correspondiente y haga clic en Editar. Aparece el cuadro de diálogo Quitar identificador de puerto de host; escriba sí y haga clic en Aceptar. Para obtener más información, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager.
Configuración: Grupos de discos y discos virtuales Creación de grupos de discos y discos virtuales Los grupos de discos se crean en la capacidad no configurado de una matriz de almacenamiento, mientras que los discos virtuales se crean en la capacidad libre de un grupo de discos. El número máximo de discos físicos admitido en un grupo de discos es 30. Los hosts conectados a la matriz de almacenamiento leen y graban datos en los discos virtuales.
Al crear un disco virtual, tenga en cuenta los usos de dicho disco virtual y seleccione una capacidad apropiada para esos usos. Por ejemplo, si un grupo de discos tiene un disco virtual que almacena archivos multimedia (que suelen ser grandes) y otro disco virtual que almacena archivos de texto (que suelen ser pequeños), el disco virtual de archivos multimedia requerirá más capacidad que el disco virtual de archivos de texto. Un grupo de discos debe organizarse según las tareas y subtareas relacionadas.
• Para crear un grupo de discos seguro: en la ficha Físico, seleccione uno o más discos físicos con función de seguridad no asignados del mismo tipo y seleccione Grupo de discos→ Crear. De manera alternativa, puede hacer clic con el botón derecho del mouse en los discos físicos con función de seguridad no asignados y seleccionar Crear grupo de discos en el menú emergente. Aparecerá la ventana Introducción (Crear grupo de discos). 2 Haga clic en Siguiente.
11 En la tabla Discos físicos no seleccionados, seleccione los discos físicos adecuados y haga clic en Agregar. NOTA: para seleccionar varios discos físicos a la vez, mantenga presionada la tecla o y seleccione discos físicos adicionales. 12 Para ver la capacidad del nuevo grupo de discos, haga clic en Calcular capacidad. 13 Haga clic en Terminar.
Creación de discos virtuales Tenga en cuenta estas importantes pautas a la hora de crear un disco virtual: • Muchos hosts pueden tener 256 números de unidad lógica (LUN) asignados por partición de almacenamiento, pero el número varía en función del sistema operativo. • Después de crear uno o más discos virtuales y de realizar una asignación, debe registrar el disco virtual con el sistema operativo.
• Para crear un disco virtual a partir de discos físicos no asignados de la matriz de almacenamiento: en la ficha Físico, seleccione uno o más discos físicos no asignados del mismo tipo y seleccione Disco virtual→ Crear. De manera alternativa, puede hacer clic con el botón derecho del mouse en los discos físicos no asignados y seleccionar Crear disco virtual en el menú emergente.
• Multimedia • Personalizar NOTA: si selecciona Personalizar, debe seleccionar un tamaño de segmento adecuado. 8 Seleccione la Propiedad del módulo de la controladora RAID preferida adecuada y haga clic en Siguiente. Aparecerá la ventana Especifique la asignación del disco virtual-paraLUN. 9 En la ventana Especifique la asignación del disco virtual-para-LUN, puede seleccionar: • Asignación predeterminada. • El Tipo de host adecuado. • Asignar después usando Vista asignaciones.
4 Seleccione uno o más discos virtuales. Para seleccionar discos virtuales no adyacentes, presione y haga clic. Para seleccionar discos virtuales adyacentes, presione y haga clic. Para seleccionar todos los discos virtuales disponibles, haga clic en Seleccionar todo. Mueva la barra deslizante Seleccione prioridad de modificación a la prioridad deseada. 5 Haga clic en Aceptar. Un mensaje le pedirá que confirme el cambio en la prioridad de modificación de disco virtual. 6 Haga clic en Sí.
Para cambiar la configuración de caché de disco virtual: 1 En la AMW, seleccione la ficha Lógico y seleccione un disco virtual. 2 En la barra de herramientas, seleccione Disco virtual→ Cambiar→ Configuración de caché. Aparecerá la ventana Cambiar configuración de caché. 3 Seleccione uno o más discos virtuales. Para seleccionar discos virtuales no adyacentes, presione y haga clic. Para seleccionar discos virtuales adyacentes, presione y haga clic.
NOTA: cuando la opción de baterías de módulo de la controladora RAID opcionales está habilitada, no aparece Habilitar la caché de escritura. La opción Habilitar la caché de escritura sin baterías sigue estando disponible pero no está seleccionada de forma predeterminada. NOTA: la caché se vacía automáticamente después de haber deshabilitado la casilla de verificación Habilitar la caché de escritura. 5 Haga clic en Aceptar.
La cantidad de tiempo que tarda una operación de cambio de tamaño de segmento depende de: • La carga de E/S del host • La prioridad de modificación del disco virtual • El número de discos físicos en el grupo de discos • El número de puertos de disco físico • La energía de procesamiento de los módulos de la controladora RAID de la matriz de almacenamiento Si desea que esta operación finalice más rápido, puede cambiar la prioridad de modificación, aunque esto podría disminuir el rendimiento de E/S.
NOTA: el valor de captura previa de lectura de caché dinámica se puede cambiar más tarde seleccionando Disco virtual→ Cambiar→ Configuración de caché. Puede cambiar el tamaño de segmento más tarde seleccionando Disco virtual→ Cambiar→ Tamaño de segmento. Los tipos de característica de E/S mostrados a continuación sólo están presentes durante el proceso de creación de disco virtual.
Con la aparición de diferentes tecnologías de disco físico, ahora es posible mezclar discos físicos con diferentes tipos de soporte y diferentes tipos de interfaces dentro de una única matriz de almacenamiento.
Puede ver el estado de disco de autocifrado de cualquier disco físico de la matriz de almacenamiento en el cuadro de diálogo Propiedades del disco físico. La información de estado muestra si el disco físico: • Es con función de seguridad • Es seguro: tiene la seguridad habilitada o deshabilitada • Es de lectura/escritura accesible: la seguridad está bloqueada o desbloqueada Puede ver el estado de disco de autocifrado de cualquier grupo de discos de la matriz de almacenamiento.
NOTA: si no ha creado una clave de seguridad para la matriz de almacenamiento, la opción Crear clave de seguridad estará activa. Si ha creado una clave de seguridad para la matriz de almacenamiento, la opción Crear clave de seguridad estará inactiva con una marca de verificación a la izquierda. Las opciones Cambiar clave de seguridad, Guardar clave de seguridad y Validar clave de seguridad estarán activas ahora. La opción Discos físicos seguros aparecerá en el menú Grupo de discos.
La contraseña de la matriz de almacenamiento protege a ésta de operaciones potencialmente destructivas de usuarios no autorizados. La contraseña de la matriz de almacenamiento es independiente del disco de autocifrado y no debe confundirse con la frase de paso utilizada para proteger copias de una clave de seguridad. Es recomendable que defina una contraseña para la matriz de almacenamiento.
4 En Frase de paso, introduzca una cadena para la frase de paso. La frase de paso deberá: • tener entre 8 y 32 caracteres de largo. • contener al menos una letra en mayúscula. • contener al menos una letra en minúscula. • contener al menos un número. • contener al menos un carácter no alfanumérico, por ejemplo, < > @ +. La frase de paso que introduzca estará enmascarada. NOTA: la opción Crear clave se activa solo si la frase de paso cumple con los criterios anteriormente mencionados.
Cambio de la clave de seguridad Al cambiar una clave de seguridad, el sistema genera una nueva clave de seguridad. La nueva clave sustituye a la anterior. No podrá ver ni leer la clave. Sin embargo, una copia de la clave de seguridad debe guardarse en algún otro medio de almacenamiento para copia de seguridad en caso de fallo del sistema o para transferirla a otra matriz de almacenamiento. Una frase de paso suministrada cifrará y descifrará la clave de seguridad para el almacenamiento en otro soporte.
5 En Frase de paso, introduzca una cadena para la frase de paso. La frase de paso deberá: • tener entre 8 y 32 caracteres de largo. • contener al menos una letra en mayúscula. • contener al menos una letra en minúscula. • contener al menos un número. • contener al menos un carácter no alfanumérico, por ejemplo, < > @ +. La frase de paso que introduzca estará enmascarada. 6 En Confirmar frase de paso, vuelva a introducir la cadena exacta que haya introducido en Frase de paso.
2 Edite la ruta predeterminada agregando un nombre de archivo al final de la ruta o haga clic en Examinar, vaya a la carpeta requerida e introduzca el nombre del archivo. 3 En Frase de paso, introduzca una cadena para la frase de paso. La frase de paso deberá: • tener entre 8 y 32 caracteres de largo. • contener al menos una letra en mayúscula. • contener al menos una letra en minúscula. • contener al menos un número. • contener al menos un carácter no alfanumérico, por ejemplo, < > @ +.
Los datos solo se pueden leer desde un disco físico con la seguridad habilitada si un módulo de la controladora RAID de la matriz de almacenamiento proporciona la clave de seguridad adecuada. Al mover los discos físicos con la seguridad habilitada de una matriz de almacenamiento a otra, también es necesario importar la clave de seguridad adecuada a la nueva matriz de almacenamiento. De lo contrario, no será posible acceder a los datos de los discos físicos con la seguridad habilitada que se movieron.
Antes de completar esta opción, asegúrese de que el disco físico que ha seleccionado sea el disco físico correcto. No puede recuperar ningún dato que esté actualmente en el disco físico. Después de completar el procedimiento de borrado seguro, el disco físico estará disponible para ser utilizado en otro grupo de discos o en otra matriz de almacenamiento.
PRECAUCIÓN: si un disco físico de repuesto dinámico no tiene estado Óptimo, siga los procedimientos del Recovery Guru para corregir el problema antes de intentar desasignar el disco físico. No puede asignar un disco físico de repuesto dinámico si está en uso (asumiendo las funciones de un disco físico fallido). Para asignar o desasignar discos físicos de repuesto dinámico: 1 En la AMW, seleccione la ficha Físico. 2 Seleccione uno o más discos físicos.
8 Seleccione los discos físicos correspondientes en el área Discos físicos no asignados, como repuestos dinámicos para el disco seleccionado, y haga clic en Aceptar. 9 Para desasignar repuestos dinámicos, en la ventana Cobertura de repuesto dinámico, seleccione los discos físicos en el área Discos físicos de repuesto dinámico. 10 Revise la información sobre la cobertura de repuesto dinámico en el área Detalles. 11 Haga clic en Desasignar. Un mensaje le indicará que confirme la operación.
Operación de repuesto dinámico Cuando falla un disco físico, el disco virtual se regenera automáticamente utilizando un repuesto dinámico disponible. Cuando hay instalado un disco físico de sustitución, se copian los datos del repuesto dinámico en el disco físico de sustitución. Esta función se denomina copia de respaldo.
Si selecciona un disco físico con función de seguridad como repuesto dinámico para un grupo de discos no seguro, aparecerá un cuadro de diálogo indicándole que se está utilizando un disco físico con función de seguridad como repuesto dinámico para un grupo de discos no seguro. La disponibilidad de protección ante pérdida del gabinete de un grupo de disco depende de la ubicación de los discos físicos que componen el grupo de discos.
Tabla 9-2. Criterios para la protección ante pérdida del gabinete Nivel de RAID Criterios para la protección ante pérdida del gabinete Nivel 5 de Asegúrese de que todos los discos físicos del grupo de discos se RAID o nivel encuentren en gabinetes de expansión diferentes. 6 de RAID Como el nivel 5 de RAID requiere un mínimo de 3 discos físicos, la protección ante pérdida del gabinete no se podrá conseguir si la matriz de almacenamiento tiene menos de 3 gabinetes de expansión.
Asignación de host a disco virtual Una vez creados los discos virtuales, deberá asignarlos a los hosts conectados a la matriz. Pautas para configurar la asignación de host a disco virtual: • Cada disco virtual de la matriz de almacenamiento sólo se puede asignar a un host o a un grupo de hosts. • Las controladoras de la matriz de almacenamiento comparten las asignaciones de host a disco virtual. • Un host o grupo de hosts debe utilizar un LUN exclusivo para acceder a un disco virtual.
Para crear asignaciones de host a disco virtual: 1 En la ventana AMW, seleccione la ficha Asignaciones. 2 En el panel Topología seleccione: • Grupo predeterminado • Nodo con asignaciones no definidas • Asignación definida individual • Grupo de hosts • Host 3 En la barra de herramientas, seleccione Asignaciones→ Definir→ Asignación adicional. Aparece la ventana Definir asignación adicional. 4 En Grupo de hosts o host, seleccione el grupo de hosts o host adecuado.
Modificación y eliminación de una asignación de host a disco virtual Puede modificar o quitar una asignación de host a disco virtual por diversos motivos, como una asignación incorrecta o la reconfiguración de la matriz de almacenamiento. La modificación o eliminación de una asignación de host a disco virtual se aplica tanto a los hosts como a los grupos de hosts.
7 Si configura un host de Linux, ejecute la utilidad rescan_dm_devs en el host y vuelva a montar el disco virtual si es necesario. Esta utilidad se instala en el host como parte del proceso de instalación de MDSM. 8 Reinicie las aplicaciones de host. Cómo cambiar la propiedad de la controladora del disco virtual Si el host tiene una única ruta de datos a la matriz de almacenamiento MD, el disco virtual debe ser propiedad de la controladora a la que está conectado el host.
Cómo quitar la asignación de host a disco virtual 1 En la AMW, seleccione la ficha Asignación. 2 Seleccione un disco virtual en el panel Asignaciones definidas. 3 Realice una de estas acciones: • Seleccione Asignaciones→ Quitar. • Haga clic con el botón derecho del mouse en el disco virtual y seleccione Quitar asignación en el menú emergente. 4 Haga clic en Sí para quitar la asignación.
Para cambiar la propiedad del módulo de la controladora RAID de un grupo de discos: 1 En la AMW, seleccione la ficha Lógico y seleccione un grupo de discos. 2 Seleccione Grupo de discos→ Cambiar→ Propiedad/ruta de acceso preferido. 3 Seleccione la ranura del módulo de la controladora RAID adecuada y haga clic en Sí para confirmar la selección.
Para cambiar el nivel de RAID de un grupo de discos: 1 En la AMW, seleccione la ficha Lógico y seleccione un grupo de discos. 2 Seleccione Grupo de discos→ Cambiar→ Nivel de RAID. 3 Seleccione el nivel de RAID adecuado y haga clic en Sí para confirmar la selección. Se iniciará la operación de nivel de RAID.
3 Vacíe la asignación de dispositivo multirruta utilizando el siguiente comando: # multipath -f /dev/mapper/mapth_x donde mapth_x es el dispositivo que desea eliminar. 4 Elimine las rutas relacionadas con este dispositivo utilizando el siguiente comando: # echo 1 > /sys/block/sd_x/device/delete donde sd_x es el nodo SD (dispositivo de disco) devuelto por el comando multirruta. Repita este comando para todas las rutas relacionadas con este dispositivo.
Asignaciones restringidas Muchos host pueden asignar hasta 256 números de unidad lógica (LUNs) (de 0 a 255) por partición de almacenamiento. Sin embargo, el número máximo de asignaciones difiere debido a las variables del sistema operativo, los problemas del controlador de migración tras error y los problemas de datos potenciales. Los hosts que aparecen en la Tabla 9-3 tienen estas restricciones de asignación.
• Si existe un host con un tipo de host restringido que forma parte de una partición de almacenamiento específica, todos los host de la partición de almacenamiento estarán limitados al número máximo de LUNs permitido por el tipo de host restringido. • No podrá mover un host con un tipo de host restringido a una partición de almacenamiento que ya tenga LUNs asignados que sean mayores de lo permitido por el tipo de host restringido.
Durante una copia de disco virtual, el mismo módulo de la controladora RAID debe poseer tanto el disco virtual de origen como el disco virtual de destino. A veces, los dos discos virtuales no tienen el mismo módulo de la controladora RAID preferido al iniciarse la copia de disco virtual. Por tanto, la propiedad del disco virtual de destino se transfiere automáticamente al módulo de la controladora RAID preferido del disco virtual de origen.
NOTA: el disco virtual podría no utilizar la nueva ruta de acceso de E/S hasta que el controlador multirruta vuelva a configurar y reconozca la nueva ruta de acceso. Esta acción suele tardar menos de cinco minutos. 3 Para cambiar la propiedad del módulo de la controladora RAID de un grupo virtual, realice estos pasos: a Seleccione la ficha Lógico. b Seleccione el grupo de discos. c Seleccione Grupo de discos→ Cambiar→ Propiedad/ruta de acceso preferido.
• Si no tiene suficiente capacidad en el grupo de discos para pasar al nuevo nivel de RAID, aparecerá un mensaje de error y la operación no continuará. Si tiene discos físicos no asignados, utilice la opción Grupo de discos→ Agregar capacidad libre (Discos físicos) para agregar capacidad adicional al grupo de discos. A continuación, vuelva a intentar la operación. Para cambiar el nivel de RAID de un grupo de discos: 1 Seleccione la ficha Lógico. 2 Seleccione el grupo de discos.
Se necesitan varias particiones de almacenamiento si: • Hosts concretos deben acceder a discos virtuales concretos de la matriz de almacenamiento. • Hosts con diferentes sistemas operativos están conectados a la misma matriz de almacenamiento. En este caso, se creará una partición de almacenamiento para cada tipo de host. Puede utilizar el Asistente de Particionamiento de almacenamiento para definir una única partición de almacenamiento.
Expansión de grupo de discos y discos virtuales Para añadir capacidad libre a un grupo de discos, hay que añadir capacidad no configurada de la matriz al grupo de discos. Puede acceder a los datos de los grupos de discos, discos virtuales y discos físicos durante todo el proceso de modificación. La capacidad libre adicional puede utilizarse para llevar a cabo una expansión de disco virtual en un disco virtual de repositorio estándar o de instantánea.
Expansión del disco virtual La expansión de discos virtuales es una operación de modificación dinámica que aumenta la capacidad de los discos virtuales estándar. NOTA: los discos virtuales de repositorio de instantánea se pueden expandir desde la CLI o desde MDSM. Todos los demás tipos de discos virtuales sólo pueden expandirse desde la CLI. Si recibe un aviso de que el disco virtual de repositorio de instantánea está llenándose, puede expandirlo desde MDSM.
Migración de grupo de discos La migración de grupo de discos le permite exportar un grupo de discos para poder importarlo en una matriz de almacenamiento diferente. También puede exportar un grupo de discos para poder almacenar datos fuera de línea. NOTA: durante el proceso de exportación (antes de importar el grupo de discos) no tendrá acceso a los datos del grupo de discos exportado. NOTA: antes de trasladar o importar el grupo de discos, debe exportarlo.
4 Localice el grupo de discos y etiquete los discos físicos. 5 Ponga el grupo de discos fuera de línea. 6 Obtenga módulos de disco físico vacíos o discos físicos nuevos. En la matriz de almacenamiento de destino: 1 Compruebe que la matriz de almacenamiento de destino tenga ranuras para discos físicos disponibles. 2 Asegúrese de que la matriz de almacenamiento de destino sea compatible con los discos físicos que va a importar.
4 Confirme que desea continuar con el proceso de importación. NOTA: algunos valores no se pueden importar durante el proceso de importar grupo de discos.
Los errores detectados por la exploración de soportes pueden ser: • Error de soporte no recuperado: los datos no se han podido leer en un primer intento ni en intentos posteriores. Para los discos virtuales con protección de redundancia, se reconstruyen los datos, se vuelven a escribir en el disco físico, se verifican y se notifica el error al registro de eventos.
5 Para deshabilitar las exploraciones de soportes en un disco virtual individual, seleccione el disco virtual en el área Seleccione discos virtuales a explorar y anule la selección de Explorar los discos virtuales seleccionados. 6 Para deshabilitar las exploraciones de soportes en un disco virtual individual, seleccione el disco virtual en el área Seleccione discos virtuales a explorar y seleccione Explorar los discos virtuales seleccionados.
Configuración: función Premium: discos virtuales de instantánea NOTA: si ha solicitado esta función, habrá recibido una tarjeta de Activación de función Premium en la misma caja que incluía la matriz de almacenamiento Dell PowerVault MD. Siga las instrucciones de la tarjeta para obtener un archivo de clave y activar la función. NOTA: la función de instantánea le permite que estén presentes al mismo tiempo hasta 16 instantáneas por LUN y 256 por matriz.
Una vez que se ha creado el disco virtual de repositorio de instantánea, se reanudan las peticiones de escritura de E/S en el disco virtual de origen. Antes de modificar un bloque de datos en el disco virtual de origen, se copia el contenido del bloque que va a modificarse en el disco virtual de repositorio de instantánea por cuestiones de seguridad.
Motivos más frecuentes para programar un disco virtual de instantánea Programar un disco virtual de instantánea puede tener muchas utilidades en un entorno de almacenamiento de datos. Los usos más comunes de un programador de instantáneas son: • Copias de seguridad de datos • Recuperación rápida en caso de pérdida de datos Una copia de seguridad de datos programada puede proteger contra la pérdida de datos de forma regular.
Pautas para la creación de programaciones de instantáneas Al crear programaciones de disco virtual de instantánea se aplican determinadas pautas: • Las operaciones de instantánea de disco virtual programadas no se llevarán a cabo si: – Se ha asignado el disco virtual de instantánea – La matriz de almacenamiento se encuentra fuera de línea o apagada – El disco virtual de instantánea funciona como un disco virtual de origen durante una operación de copia de disco virtual – Hay una operación de copia p
Para obtener más información sobre cómo programar discos virtuales de instantánea, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager y la Guía de CLI. Creación de un disco virtual de instantánea mediante la ruta de acceso sencilla Puede elegir la ruta de acceso sencilla para crear un disco virtual de instantánea si el grupo de discos del disco virtual de origen tiene la cantidad de espacio libre necesaria.
• Programación: crea el disco virtual de instantánea en un momento determinado o según un intervalo regular. Si no se especifica una programación, la operación de instantánea se inicia inmediatamente. Este parámetro se puede utilizar también para aplicar una programación a un disco virtual de instantánea existente.
NOTA: para obtener más información sobre cómo asignar el disco virtual de instantánea al nodo secundario, consulte Dell PowerVault MD3600f and MD3620f Storage Arrays With Microsoft Windows Server Failover Clusters (Matrices de almacenamiento Dell PowerVault MD3600 y MD3620 con clúster de migración tras error Microsoft Windows Server) en dell.com/support/manuals. NOTA: puede crear instantáneas simultáneas de un disco virtual de origen en el grupo de discos de origen y en otro grupo de discos.
Antes de crear un disco virtual de instantánea, el servidor host debe encontrarse en el estado correcto. Para garantizar que el servidor host está preparado adecuadamente para crear un disco virtual de instantánea, puede utilizar una aplicación con este fin o bien realizar los pasos siguientes: 1 Detenga toda la actividad de E/S del origen. 2 En la AMW, seleccione la ficha Lógico y seleccione un disco virtual de origen válido. 3 Seleccione Disco virtual→ Instantánea→ Crear.
10 Haga clic en Aceptar. Después de crear uno o varios discos virtuales de instantánea, monte el disco virtual de origen y reinicie la aplicación de host utilizando dicho disco virtual de origen. 11 En la AMW, seleccione la ficha Asignaciones, realice las asignaciones entre el disco virtual de origen y el host que accede al disco virtual de instantánea. NOTA: en algunos casos, se pueden producir conflictos al asignar el mismo host a un disco virtual de origen y a su disco virtual de instantánea asociado.
• • • • • • • 168 Nombre del disco virtual de repositorio de instantánea: nombre especificado por el usuario que ayuda a asociar el disco virtual de repositorio de instantánea con su disco virtual de repositorio de instantánea y su disco virtual de origen correspondientes. Asignación de capacidad: este parámetro le permite elegir dónde crear el disco virtual de repositorio de instantánea.
Preparación de los servidores host para crear la instantánea mediante la ruta de acceso avanzada NOTA: antes de utilizar la función Premium de discos virtuales de instantánea en una configuración en clúster de Microsoft Windows, debe asignar primero el disco virtual de instantánea al nodo del clúster propietario del disco virtual de origen. Con esto se garantiza que los nodos del clúster reconozcan correctamente el disco virtual de instantánea.
Recuerde las siguientes directrices antes de crear un disco virtual de instantánea: • Los siguientes tipos de discos virtuales no son discos virtuales de origen válidos: – Discos virtuales de repositorio de instantáneas – Discos virtuales de instantánea – Discos virtuales de repositorio de replicación – Discos virtuales de destino que participan en una copia de disco virtual. NOTA: la copia de disco virtual es una función avanzada (Premium).
3 Elimine las letras de unidad del disco virtual de origen en Windows o desmonte las unidades virtuales en Linux para garantizar una copia estable de la unidad para la instantánea. Si esto no se realiza, se indicará que la operación de instantánea ha finalizado correctamente pero los datos de la instantánea no se habrán actualizado correctamente.
4 Haga clic con el botón derecho del mouse en el disco virtual de origen y seleccione Crear disco virtual de instantánea en el menú emergente. Aparecerá el cuadro de diálogo Asistente para crear disco virtual de instantánea - Introducción. 5 Seleccione Avanzado y haga clic en Siguiente. Aparecerá la ventana Especifique nombres. 6 Introduzca el Nombre del disco virtual de instantánea y el Nombre del disco virtual de repositorio de instantánea y haga clic en Siguiente. Aparecerá la ventana Asignar capacidad.
12 Haga clic en Terminar. Aparece la ventana Finalizado. 13 Haga clic en Aceptar. 14 En la ficha Asignaciones, realice las asignaciones entre el disco virtual de instantánea y el host que accede al disco virtual de instantánea. 15 Para registrar el disco virtual de instantánea con el sistema operativo de host, ejecute la utilidad hot_add basada en host. 16 Para asociar la asignación entre el nombre de matriz de almacenamiento y el nombre de disco virtual, ejecute la utilidad SMdevices basada en host.
• • • • Tanto si utiliza el número de secuencia proporcionado por el software que rellena (de forma predeterminada) el campo Nombre del disco virtual de instantánea o Nombre del disco virtual de repositorio de instantánea, el siguiente nombre predeterminado para un disco virtual de instantánea o un disco virtual de repositorio de instantánea seguirá utilizando el número de secuencia determinado por el software.
No es posible aumentar la capacidad de almacenamiento de un disco virtual de repositorio de instantánea si dicho disco cumple una de las condiciones siguientes: • El disco virtual está utilizando una o varias unidades de repuesto dinámico. • El disco virtual se encuentra en un estado diferente de Óptimo. • Cualquier disco virtual del grupo de discos está en un estado de modificación. • La controladora propietaria de este disco virtual está actualmente añadiendo capacidad a otro disco virtual.
4 Para aumentar la capacidad del disco virtual de repositorio de instantánea, utilice uno de los siguientes métodos: • Utilice la capacidad libre en el grupo de discos del disco virtual de repositorio de instantánea; vaya al paso 5. • Agregue capacidad no configurada, o discos físicos al grupo de discos del disco virtual de repositorio de instantáneas; vaya al paso 7. 5 En Aumentar capacidad mediante, introduzca o seleccione la capacidad adecuada. 6 Haga clic en Aceptar. Se actualizará la ficha Lógico.
10 Haga clic en Agregar. Se cerrará la ventana Agregar discos físicos. 11 Compruebe el área Discos físicos a agregar [gabinete, ranura] para asegurarse de que se hayan agregado los discos físicos correctos. 12 Acepte la capacidad final, o introduzca o seleccione la capacidad adecuada en el campo Aumentar capacidad mediante. 13 Haga clic en Aceptar. Se actualizará la ficha Lógico. El disco virtual de repositorio de instantánea que haya aumentado su capacidad mostrará un estado de Operación en curso.
• Desea maximizar el rendimiento de la matriz de almacenamiento deteniendo la actividad de copia con escritura en el disco virtual de repositorio de instantánea. NOTA: si no pretende volver a crear el disco virtual de instantánea más adelante, en el panel Lógico, seleccione el disco virtual de instantánea y seleccione Disco virtual→ Eliminar para quitarlo. El disco virtual de repositorio de instantánea asociado también se quitará.
Para preparar el servidor host y el disco virtual: 1 Detenga toda la actividad de E/S en el disco virtual de origen y en el disco virtual de instantánea (si está montado). 2 Vacíe la caché del disco virtual de origen y del disco virtual de instantánea (si está montado) mediante el sistema Windows. Cuando el host se lo pida, escriba: SMrepassist -f y presione . Para obtener más información, consulte “Utilidad SMrepassist” en la página 314.
NOTA: si no se siguen estas instrucciones adicionales es posible que cree discos virtuales de instantánea inutilizables. Para obtener más información, consulte los temas de la ayuda en línea de PowerVault Modular Disk Storage Manager. • Para utilizar esta opción, el disco virtual de instantánea debe estar en estado Óptimo o en estado Deshabilitado. • Cuando utilice esta opción, se utilizan los parámetros de nombre de instantánea y el disco virtual de repositorio de instantánea configurados previamente.
Puede establecer una prioridad para la operación de reversión. Con una prioridad más alta se asignan más recursos de sistema a la operación de reversión y esto afecta al rendimiento general del sistema. Reglas y pautas para realizar una reversión de instantánea Las siguientes reglas y pautas se aplican a la realización de una reversión de instantánea: • Revertir un disco virtual de base para un disco virtual de instantánea no afecta al contenido de los discos virtuales de instantánea.
Opciones de la línea de comandos De forma opcional, también puede utilizar le interfaz de línea de comandos (CLI) para iniciar, cancelar, reanudar o modificar la prioridad de una reversión de instantánea. Para obtener más información, consulte la Guía de CLI. Protección contra una reversión de instantánea fallida Para proteger los datos del disco virtual base, es recomendable que cree un nuevo disco virtual a partir del disco virtual básico antes de iniciar una operación de reversión.
3 En el área Seleccionar prioridad de reversión, utilice la barra deslizante para definir la prioridad de reversión. NOTA: si se establece la prioridad con una velocidad baja, la actividad de escritura de datos habitual pasa a ser de prioridad alta y la operación de reversión tarda más en completarse. Si se establece la prioridad con una velocidad alta, la operación de reversión pasa a ser de prioridad alta y se reduce la actividad de escritura de datos.
Cancelación de una reversión de instantánea AVISO: Riesgo de pérdida de datos: si cancela una instantánea mientras esté en curso, el disco virtual básico puede quedar inutilizable y el disco virtual de instantánea presenta un estado de error en el software MD Storage Management. Por lo tanto, no cancele una reversión de instantánea a menos que existan opciones de recuperación fiables para restaurar el contenido del disco virtual básico. 1 En la ventana administración de matrices, seleccione la ficha Lógico.
Configuración: Función Premium Copia de disco virtual NOTA: una copia de disco virtual sobrescribe los datos del disco virtual de destino. Antes de iniciar una copia de disco virtual, asegúrese de que ya no necesita los datos o haga una copia de seguridad de los datos del disco virtual de destino. NOTA: si ha solicitado esta función, habrá recibido una tarjeta de activación de función Premium en la misma caja que incluía la matriz de almacenamiento Dell PowerVault MD.
Las razones para utilizar una copia de disco virtual son las siguientes: • Copia de datos para un mejor acceso: a medida que cambian los requisitos de almacenamiento para un disco virtual, puede utilizar una copia de disco virtual para copiar los datos en un disco virtual de un grupo de discos que utilice unidades con una capacidad mayor dentro de la misma matriz de almacenamiento.
Copia fuera de línea Una copia fuera de línea lee datos desde el disco virtual de origen y los copia en un disco virtual de destino, mientras se suspenden todas las actualizaciones para el disco virtual de origen cuando la copia está en curso. En una copia de disco virtual fuera de línea, la relación se produce entre un disco virtual de origen y un disco virtual de destino.
Antes de modificar un bloque de datos en el disco virtual de origen, se copia el contenido del bloque que va a modificarse en el disco virtual de repositorio de instantánea. Dado que en el disco virtual de repositorio de instantánea se almacenan copias de los datos originales en dichos bloques de datos, los cambios efectuados posteriormente en esos bloques de datos sólo se escribirán en el disco virtual de origen.
Permisos de lectura/escritura de disco virtual Una vez finalizada la copia de disco virtual, el disco virtual de destino pasa a ser automáticamente de sólo lectura para los hosts. El disco virtual de destino rechaza las peticiones de lectura y escritura mientras la operación de copia de disco virtual tiene el estado Pendiente o En curso o si la operación falla antes de que se complete la copia.
Restricciones de copia de disco virtual Antes de realizar cualquier tarea de copia de disco virtual, debe conocer y respetar las restricciones que se mencionan en esta sección. Las restricciones se aplican al disco virtual de origen, al disco virtual de destino y a la matriz de almacenamiento. • Mientras una copia de disco virtual tenga el estado En curso, Pendiente o Ha fallado, el disco virtual de origen sólo está disponible para la actividad de E/S de lectura.
Creación de una copia de disco virtual Los discos virtuales de origen que estén participando en una copia de disco virtual estarán disponibles para actividad de E/S de lectura sólo mientras una copia de disco virtual tenga un estado En curso o Pendiente. Se permiten solicitudes de escritura después de finalizada la copia de disco virtual.
Una copia de disco virtual sobrescribe los datos del disco virtual de destino y automáticamente convierte el disco virtual de destino en uno de sólo lectura para los hosts. Si hay 16 copias de disco virtual con el estado En curso, cualquier copia de disco virtual posterior tendrá un estado Pendiente, hasta que una de las 16 copias de disco virtual finalice.
• Un error en la matriz de almacenamiento que afecte al disco virtual de origen o al disco virtual de destino. Cuando la copia de disco virtual falla, se registra un evento crítico en el Registro de eventos y aparece un icono Requiere atención en la AMW. Mientras una copia de disco virtual tenga este estado, el host tendrá acceso de sólo lectura al disco virtual de origen.
Administrador de copias Después de crear una copia de disco virtual mediante el Asistente para crear copia, puede supervisar la copia de disco virtual a través del Administrador de copias. En el Administrador de copias, un disco virtual se puede volver a copiar, detener o quitar. También puede modificar los atributos como, por ejemplo, la prioridad de copia y el atributo Sólo lectura del disco virtual de destino. Puede ver el estado de una copia de disco virtual en el Administrador de copias.
3 En la AMW, seleccione la ficha Lógico y seleccione el disco virtual de origen. 4 Seleccione Disco virtual→ Crear copia. Aparecerá la ventana Seleccionar el disco virtual de origen y Tipo de copia. 5 En el área Seleccionar el disco virtual de origen, seleccione el disco virtual correspondiente. 6 En el área Seleccionar Tipo de copia, seleccione Fuera de línea o Tipo de copia en línea.
• Configuración del disco virtual: número de unidades en los grupos de discos virtuales • Tipo de disco virtual: es posible que los discos virtuales de instantánea tarden más tiempo en copiarse que los discos virtuales estándar Durante una copia de disco virtual, los recursos de la matriz de almacenamiento se desvían del procesamiento de la actividad de E/S para completar una copia de disco virtual. Esto afecta al rendimiento global de la matriz de almacenamiento.
Cómo detener una copia de disco virtual Puede detener una operación de copia de disco virtual que tenga el estado En curso, Pendiente o de Ha fallado. Al detener una copia de disco virtual con el estado Ha fallado, se borra el estado Requiere atención que se muestra para la matriz de almacenamiento. Tenga en cuenta estas pautas a la hora de detener una copia de disco virtual: • Para utilizar esta opción, seleccione sólo un par de copia en el Administrador de copias.
Preparación de los servidores host para una nueva copia de un disco virtual NOTA: antes de crear una nueva copia de un disco virtual de origen, detenga toda la actividad de acceso a datos (E/S) o suspenda la transferencia de datos al disco virtual de origen (y, si procede, al disco de destino) para asegurarse de poder capturar una imagen puntual en un momento preciso del disco virtual de origen.
Cómo volver a copiar un disco virtual Puede utilizar el Administrador de copias para crear una nueva copia de disco virtual para un disco virtual de origen y un disco virtual de destino seleccionados. Utilice esta opción cuando haya detenido una copia de disco virtual y desee iniciarla de nuevo o cuando una copia de disco virtual haya fallado o haya finalizado. La copia de disco virtual se vuelve a iniciar desde el principio.
Quitar los pares de copia Puede quitar una o más copias de disco virtual mediante el Administrador de copias. La información relacionada con copias de disco virtual del disco virtual de origen y el disco virtual de destino se quita del cuadro de diálogo Propiedades del disco virtual y de los cuadros de diálogo de Perfil de matriz de almacenamiento. Al quitar una copia de disco virtual de la matriz de almacenamiento, el atributo Sólo lectura del disco virtual de destino también se quita.
Configuración: Función Premium Actualización a un nivel de alto rendimiento La función Premium Nivel de alto rendimiento de una matriz serie MD3600f aumenta el rendimiento del sistema más allá del de una matriz serie MD3600f que funcione en un nivel de rendimiento estándar. Si se solicita esta función, se incluirá una tarjeta de activación de función Premium en la caja con la matriz de almacenamiento.
Configuración: Función Premium - Actualización a un nivel de alto rendimiento
Configuración: Función Premium Replicación remota La función Premium Replicación remota habilita la replicación de datos en tiempo real entre dos matrices de almacenamiento en ubicaciones separadas. Gracias a la replicación remota, se pueden crear hasta 16 pares de disco virtual replicados en una matriz de almacenamiento. Un par de disco virtual replicado se crea a partir de dos discos virtuales estándar, que son ambos estructuras lógicas de almacenamiento de datos creadas en una matriz de almacenamiento.
Para obtener más información sobre la configuración del entorno de conmutador, ver “Configuraciones requeridas para la agrupación por zonas de conmutación” en la página 208. Activación de la replicación remota NOTA: si ha solicitado la función Replicación remota, habrá recibido una tarjeta de activación de función Premium en la caja de envío de la matriz de almacenamiento Dell PowerVault MD. Para instalar y habilitar esta función, siga las instrucciones de la tarjeta.
Discos virtuales de repositorio de replicación La utilización de la función Premium Replicación remota en la matriz de almacenamiento requiere la creación de dos discos virtuales de repositorio de replicación en uno de los grupos de disco en la matriz de almacenamiento.
Pares de disco virtual primario y secundario Después de la activación de la función Replicación remota y de la configuración de la red Fabric de FC, se crearán los pares de replicación de disco virtual individual. Se pueden establecer hasta 16 pares de replicación de disco virtual. Cada par consiste de un disco virtual primario (en línea) y de un disco virtual secundario (fuera de línea) que poseen capacidad idéntica.
Disco virtual de instantánea y Copia de disco virtual son funciones Premium que deben encontrarse habilitadas y activadas en la matriz de almacenamiento primaria. Particionamiento de almacenamiento con replicación remota El particionamiento de almacenamiento permite a los hosts compartir el acceso a los discos virtuales de una matriz de almacenamiento.
PRECAUCIÓN: si se inicia una inversión de función primaria/secundaria mientras esté en curso una copia de disco virtual, la copia de disco virtual fallará y no podrá reiniciar. • Cree un disco virtual de instantánea del disco virtual secundario y, a continuación, realice una copia de disco virtual del disco virtual de instantánea. Expansión de disco virtual con replicación remota La expansión de disco virtual (VDE) aumentará la capacidad de un disco virtual ya existente.
NOTA: no agrupe por zonas el puerto de enlace ascendente (E_port) que conecta (en cascada) los conmutadores dentro de una red Fabric. Las configuraciones de agrupación por zonas de conmutación se configuran normalmente usando el software de administración de conmutadores proporcionado por el proveedor de conmutadores Fibre Channel. Este software se incluye con el propio conmutador o se puede descargar del sitio web del proveedor.
Configuración y administración de la replicación remota Prerrequisitos Antes de configurar la replicación remota entre dos matrices de almacenamiento, asegúrese de que: • Se active la función Premium Replicación remota. • La matriz de almacenamiento local contenga dos discos virtuales de repositorio de replicación (creados durante la activación). • La matriz de almacenamiento local contenga el disco virtual primario que se replicará.
Activación de la función Premium de replicación remota y creación de discos virtuales de replicación Para activar la función Replicación remota y crear los dos discos virtuales de repositorio de replicación necesarios, puede: • Activar la función, y, a continuación, crear los dos discos virtuales de replicación a partir de la capacidad total sin configurar en la matriz de almacenamiento, o • Activar la función, y, a continuación, crear los dos discos virtuales de replicación a partir de la capacidad sin
• Si ha seleccionado la opción Manual, aparecerán una tabla Discos físicos no seleccionados cumplimentada, una tabla Discos físicos seleccionados vacía y una lista desplegable de niveles de RAID disponibles. 5 En la lista desplegable Seleccione el nivel de RAID, seleccione el nivel de RAID para el grupo de discos. La tabla Seleccionar capacidad muestra los discos virtuales disponibles para el nivel de RAID.
3 Haga clic en Terminar. Aparecerá el mensaje Finalizada (Activación de la replicación remota). 4 Haga clic en Aceptar. La función Premium Replicación remota ya está activada. El panel Lógico muestra los dos discos virtuales de repositorio de replicación como parte del grupo de discos. Creación de una replicación remota Antes de crear una replicación remota, asegúrese de que se cumplan todos los prerrequisitos. Ver “Prerrequisitos” en la página 210 para obtener más información.
Selección de disco virtual secundario PRECAUCIÓN: la creación de un par de disco virtual inicia un proceso entre los discos virtuales primario y secundario que sobrescribe todos los datos existentes en el disco virtual secundario y configura el disco con la opción Solo lectura.
• En el modo asíncrono, el módulo de la controladora RAID en la matriz de almacenamiento primaria devuelve un mensaje de finalización de E/S a la matriz de almacenamiento de host antes de que los datos se hayan copiado correctamente en la matriz de almacenamiento secundaria.
Para configurar la prioridad y el método de sincronización: 1 En el asistente Seleccionar configuración de sincronización (Crear replicación remota), seleccione la prioridad de sincronización en la barra deslizante. 2 Seleccione una resincronización Manual o Automática. • Resincronización automática: la resincronización comienza inmediatamente después de restablecerse la comunicación entre los discos duros virtuales replicados.
• En la matriz de almacenamiento local, el panel Propiedades muestra el estado de replicación como Sincronizando y la barra de progreso de sincronización muestra el tiempo calculado hasta la finalización.
PRECAUCIÓN: para evitar una posible pérdida de datos, verifique que los discos virtuales no estén en uso, o que se haya instalado una unidad multirruta en el host. Si cambia la propiedad/ruta de acceso preferido del módulo de la controladora RAID mientras una aplicación esté usando uno de los discos virtuales, se interrumpirá la actividad de E/S y podrían producirse errores de E/S.
• Para guardar la información, haga clic en Guardar como y, a continuación, vaya al paso 6. 6 En la zona Selección de sección de la ventana Guardar perfil seleccione cada sección que desea guardar. 7 Para guardar el archivo: • Guarde el archivo en el directorio predeterminado, o • Guarde el archivo en otro directorio seleccionándolo en la lista desplegable Buscar en. 8 En el campo Nombre de archivo, introduzca un nombre para el archivo y haga clic en Guardar. El archivo se guardará como un archivo .
3 Seleccione Ver elementos lógicos asociados.
Iconos de estado del disco virtual En la ficha Dispositivos en la EMW, los siguientes iconos representan el estado de cada disco virtual: Cambio del modo de escritura y de la pertenencia al grupo de coherencia Tabla 13-1.
El modo de escritura de una replicación remota se selecciona en el momento de su creación. No obstante, puede cambiar más tarde el modo de escritura en una replicación remota, además de cambiar la pertenencia del disco virtual secundario a un grupo de coherencia de escritura. Para obtener más información sobre los modos de escritura y los grupos de coherencia de escritura, vaya al tema de ayuda Configuración del modo de escritura para la creación de una replicación remota en línea.
• El disco virtual secundario será coherente con la escritura o no coherente con la escritura. • El método de resincronización será Manual o Automático. Resincronización de discos virtuales Hay dos métodos de resincronización para las replicaciones remotas: • Resincronización manual; ver “Resincronización manual de los discos virtuales” en la página 227. • Resincronización automática; ver “Resincronización automática de los discos virtuales” en la página 227.
3 El propietario de módulo de la controladora RAID escribe los datos para el disco virtual primario. 4 El propietario de módulo de la controladora RAID inicia una operación de transferencia de datos al disco virtual secundario en la matriz de almacenamiento secundaria. La comunicación entre los discos virtuales primario y secundario puede suspenderse o dejar de estar sincronizada.
Cambio de la prioridad y el método de sincronización La prioridad de sincronización define cuánto tiempo y los recursos de procesamiento que se asignan a la sincronización del disco virtual primario y del secundario de una replicación remota en lo relacionado con el rendimiento del sistema. Aumentar la prioridad de sincronización de una replicación remota puede degradar el rendimiento del sistema. Las prioridades de sincronización se pueden reconfigurar en cualquier momento.
6 Haga clic en Aceptar. Aparecerá el mensaje de confirmación Cambiar configuración de sincronización. 7 En el mensaje de confirmación Cambiar configuración de sincronización, haga clic en Sí. La barra de progreso Cambiar prioridad de la sincronización mostrará el progreso de la resincronización. 8 Haga clic en Aceptar. Discos virtuales no sincronizados La comunicación entre los discos virtuales primario y secundario puede suspenderse o dejar de estar sincronizada.
Resincronización automática de los discos virtuales Cuando se selecciona la opción de resincronización automática, el módulo de la controladora RAID que posee el disco virtual primario comienza de inmediato a resincronizar los datos en el par de replicación remota después de que se restaure la comunicación. NOTA: cuando se escoge la resincronización automática, podría tener lugar una pérdida de datos si se interrumpe una resincronización en curso.
PRECAUCIÓN: podría darse una pérdida potencial de acceso a los datos si invierte las funciones entre el disco virtual secundario y el primario mientras esté en curso una copia de disco virtual. La inversión de funciones podría tener éxito, pero la copia de disco virtual fallará y no se podrá reiniciar. • No podrá realizar una copia de disco virtual en un disco virtual secundario en una replicación remota de disco virtual.
Suspensión de una replicación remota 1 En la AMW de la matriz de almacenamiento que contiene el disco virtual primario, seleccione la ficha Lógico. 2 En la ficha Lógico haga clic con el botón derecho del mouse en el disco virtual primario de un par replicado y, a continuación, seleccione la opción Suspender replicación. Se mostrará el cuadro de diálogo Suspender par replicado. La tabla Pares replicados muestra todos los pares replicados en las matrices de almacenamiento locales y en las remotas.
5 En el cuadro de texto Confirmación, escriba Sí. Se reanudará la replicación de disco virtual remoto. Los paneles Propiedades en la AMW para la matriz de almacenamiento local y la matriz de almacenamiento remoto muestran el estado de replicación como Sincronizado para los discos virtuales primario y secundario.
Prueba de comunicación entre los discos virtuales primario y secundario Cuando una resincronización es manual o durante una situación de recuperación tras un desastre, es recomendable comprobar la comunicación entre el disco virtual primario y el disco virtual secundario en una replicación remota. Para obtener más información sobre la sincronización y la resincronización en replicaciones de disco virtual remoto, consulte los siguientes temas: • “Discos virtuales sincronizados normalmente” en la página 223.
Eliminación de un disco virtual primario PRECAUCIÓN: dependiendo de qué funciones Premium estén habilitadas en la matriz de almacenamiento, la eliminación de un disco virtual primario puede eliminar todos los discos virtuales asociados, resultando en una posible pérdida de datos en esos discos virtuales. NOTA: no puede eliminar un disco virtual primario mientras se esté sincronizando.
Eliminación de un disco virtual primario en un par replicado de una matriz de almacenamiento 1 Detenga toda la actividad de E/S para el disco virtual primario y desmonte cualquier sistema de archivos en el disco virtual primario. 2 En la AMW de la matriz de almacenamiento que contiene el disco virtual primario, seleccione la ficha Lógico. 3 En el panel Lógico haga clic con el botón derecho del mouse en el disco virtual primario y, a continuación, seleccione Eliminar.
4 Seleccione uno o más discos virtuales que borrar y luego haga clic en Eliminar. Se mostrará el mensaje Confirme la eliminación de los discos virtuales. 5 En el cuadro de texto Confirmación, introduzca Sí. A continuación, haga clic en Aceptar. Se mostrará la barra de progreso Eliminar discos virtuales. 6 Cuando se complete la eliminación, haga clic en Aceptar. Se quitará la relación de replicación y se destruirá la replicación de disco virtual remoto.
Para quitar la replicación remota de una matriz de almacenamiento: 1 En la AMW de la matriz de almacenamiento que contiene el disco virtual primario, seleccione la ficha Lógico. 2 En la ficha Lógico haga clic con el botón derecho del mouse en el disco virtual primario de un par replicado y, a continuación, seleccione la opción Quitar relación de replicación. Se mostrará el cuadro de diálogo Quitar relación de replicación.
2 Haga clic en Sí. La función Premium Replicación remota se desactivará y los dos discos virtuales de repositorio de replicación se eliminarán de la matriz de almacenamiento. Deshabilitación de la función Premium de replicación remota Antes de deshabilitar la función Premium Replicación remota, se deben quitar todas las replicaciones de discos virtuales remotas de la matriz de almacenamiento. Ver “Deshabilitación de la función Premium de replicación remota” en la página 236.
Configuración: Multirruta de Device Mapper para Linux Descripción general La matriz de almacenamiento serie MD3600f utiliza una infraestructura de software del sistema operativo Linux, conocida como Device Mapper (DM), que permite funciones multirruta en servidores host de Linux. La función multirruta de DM se proporciona a través de una combinación de controladores y utilidades.
• Identifica un nuevo LU en multirruta y configura automáticamente un nuevo nodo multirruta • Proporciona persistencia de nombres de dispositivo para los dispositivos DM bajo /dev/mapper/ Uso de dispositivos multirruta DM NOTA: si se utilizan o modifican nodos distintos de los nodos de dispositivo multirruta podrían producirse problemas en el sistema de archivos o la matriz, incluida la pérdida de comunicación con la matriz o daños en el sistema de archivos.
3 Asigne las matrices recién creadas al servidor host. NOTA: las matrices configuradas con MDCU se agregan automáticamente a la lista de dispositivos de la Ventana de Administración Enterprise (EMW) de PowerVault Modular Disk Storage Manager. Pasos de configuración de Device Mapper Para realizar la configuración multirruta de DM y poner a disposición del servidor host de Linux el almacenamiento disponible: 1 Busque los discos virtuales. Ver “Búsqueda de discos virtuales recién agregados” en la página 239.
Visualización de la topología de dispositivo multirruta mediante el comando multipath El comando multipath agrega los discos virtuales recientemente explorados y asignados a las tablas de Device Mapper y crea entradas para ellos en el directorio /dev/mapper del servidor host. Estos dispositivos son los mismos que los otros dispositivos de bloque del host.
\_ 4:0:0:22 sdx 65:112 [active][ready] \_ round-robin 0 [prio=1][enabled] \_ 6:0:0:22 sdcl 69:144 [active][ghost donde: mpathb es el nombre del dispositivo virtual creado por Device Mapper. Se encuentra en el directorio /dev/mapper.
Si es correcto, el comando no mostrará ninguna salida. Para verificar si es correcto y ver los nombres exactos de partición, el usuario puede utilizar estos comandos para ver los nombres de partición completos asignados.
Listo para usar Los discos virtuales recientemente creados en la matriz serie MD3600f están ahora configurados y listos para utilizar. Los futuros reinicios buscarán automáticamente dispositivos multirruta junto con sus particiones. Desactivar la unidad local en el controlador multirruta Si los controladores multirruta están conectados con las redes de área local (SANs), puede ser útil excluir o desactivar determinados dispositivos en el archivo /etc/multipath.conf.
Información importante acerca de particiones especiales Cuando se utiliza Device Mapper con la matriz serie MD3600f, todos los discos físicos se asignan a un nodo de dispositivo de disco. Esto incluye un tipo de dispositivo especial utilizado para la administración en banda de la matriz serie MD3600f, conocido como el Disco de acceso o Dispositivo universal xport. PRECAUCIÓN: determinados comandos, como por ejemplo, lsscsi, muestran una o más instancias de dispositivos Universal Xport.
Tabla 14-1. Comandos de Device Mapper Comando Descripciones rescan_dm_devs Secuencia de comandos proporcionada por Dell. Fuerza una reexploración del bus SCSI del host y agrega dispositivos multirruta cuando sea necesario. Para su uso cuando: • Los LUNs se asignan de forma dinámica a los hosts. • Se agregan nuevos destinos al host. • Es necesaria la conmutación por recuperación de la matriz de almacenamiento.
• La conmutación por recuperación puede ser lenta cuando el sistema host esté experimentando una E/S pesada. El problema se agrava si el servidor host también experimenta una utilización de procesador muy alta. • El servicio multirruta de Device Mapper puede ser lento cuando el sistema host experimenta una E/S pesada. El problema se agrava si el servidor host también experimenta una utilización del procesador muy alta. • Si el disco raíz no está en la lista negra del archivo multipath.
Pregunta Respuesta Quité un LUN, pero la El dispositivo multirruta sigue ahí después de quitar asignación multirruta sigue ahí. los LUNs. Ejecute multipath –f para quitar la asignación multirruta. Por ejemplo, si los dispositivos relacionados con /dev/dm-1 se eliminan, deberá ejecutar multipath –f /dev/dm-1 para quitar /dev/dm-1 de la tabla de asignaciones de DM.
Configuración: Multirruta de Device Mapper para Linux
Administración: Descargas de firmware Descarga de los paquetes de la controladora RAID y de la NVSRAM Existe un número de versión para cada archivo de firmware. El número de versión indica si el firmware es una versión principal o una versión secundaria. Puede utilizar la Ventana de Administración Enterprise (EMW) para descargar y activar tanto las versiones de firmware principales como las versiones de firmware secundarias.
Descarga del firmware de la controladora RAID y de la NVSRAM NOTA: las E/S en la matriz pueden continuar mientras se actualiza el firmware de la controladora RAID y de la NVSRAM. NOTA: Dell recomienda actualizar el firmware y la NVSRAM durante los periodos de mantenimiento cuando no se utilice la matriz para operaciones de E/S. NOTA: el gabinete RAID debe contener como mínimo dos unidades de disco para actualizar el firmware de la controladora.
5 Si desea descargar un archivo NVSRAM con el firmware, seleccione Transferir el archivo NVSRAM con el firmware del módulo de la controladora RAID y haga clic en Seleccionar archivo junto a Archivo NVSRAM seleccionado. 6 Para transferir los archivos al módulo de la controladora RAID sin activarlos, haga clic en Transferir archivos pero no activarlos (activarlos después). 7 Haga clic en Transferir.
11 Haga clic en Firmware en el área Descargar. Si selecciona una matriz de almacenamiento que no se puede actualizar, el botón Firmware estará deshabilitado. Aparece el cuadro de diálogo Descargar firmware. Aparecen la versión de firmware y la versión de NVSRAM actuales de las matrices de almacenamiento seleccionadas.
18 Haga clic en Sí. La descarga se inicia y aparece un indicador de progreso en la columna Estado de la ventana Actualizar firmware del módulo de la controladora RAID. Descarga únicamente firmware de NVSRAM También puede utilizar la interfaz de línea de comandos (CLI) para descargar y activar NVSRAM en varias matrices de almacenamiento. Para obtener más información, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager.
5 Haga clic en Transferir. NOTA: si el archivo seleccionado no es válido o no es compatible con la configuración de la matriz de almacenamiento actual, aparecerá el cuadro de diálogo Error de selección de archivo. Haga clic en Aceptar para cerrarlo y elija un archivo NVSRAM compatible. 6 Haga clic en Sí en el cuadro de diálogo Confirmar descarga. Se iniciará la descarga. 7 Realice una de estas acciones: • Seleccione Herramientas→ Actualizar firmware del módulo de la controladora RAID.
NOTA: si selecciona las matrices de almacenamiento con tipos de módulo de la controladora RAID diferentes que no se pueden actualizar con el mismo archivo NVSRAM y hace clic en NVSRAM, aparecerá el cuadro de diálogo Módulos de la controladora RAID incompatibles. Haga clic en Aceptar para cerrar el cuadro de diálogo y seleccione las matrices de almacenamiento con tipos de módulo de la controladora RAID similares.
PRECAUCIÓN: riesgo de errores de aplicación: descargar el firmware podría causar errores de aplicación. Al descargar firmware, tenga en cuenta estas importantes pautas para evitar el riesgo de errores de aplicación: • Una descarga incorrecta del firmware puede provocar daños en los discos físicos o pérdida de datos. Realice las descargas únicamente bajo la supervisión de su representante de soporte técnico. • Detenga toda E/S a la matriz de almacenamiento antes de la descarga.
6 Escriba sí y haga clic en Aceptar. La ventana Descarga del firmware de disco físico - Progreso muestra el progreso de la descarga del firmware de disco físico. 7 Una vez completada la descarga de firmware, haga clic en Cerrar. Para obtener más información, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager.
2 En el área Seleccionar gabinetes, seleccione los gabinetes de expansión en los que desee descargar firmware o seleccione Seleccionar todo para seleccionar todos los gabinetes de expansión de la matriz de almacenamiento. Cada gabinete de expansión seleccionado debe tener la misma Id. de producto. 3 Haga clic en Seleccionar archivo. Aparece el cuadro de diálogo Seleccionar el archivo de firmware de la tarjeta de entorno (EMM). 4 Seleccione el archivo para descargar y haga clic en Aceptar.
Tecnología de supervisión automática, análisis y generación de informes (SMART) Tecnología de supervisión automática, análisis y generación de informes (SMART) supervisa el rendimiento interno de todos los componentes de disco físico para detectar errores que indiquen el potencial de fallo en disco físico. SMART utiliza esta información para notificar si el fallo es inminente, de modo que un disco físico se pueda sustituir antes de que se produzca el fallo.
Administración: Descargas de firmware
Administración: Instalación de componentes de matriz Herramientas recomendadas Para llevar a cabo los procedimientos descritos en esta sección, necesitará los elementos siguientes: • Llave para la cerradura del sistema • Destornillador Phillips del n.
Bisel anterior (opcional) Extracción del bisel anterior 1 Desbloquee el bisel anterior mediante la llave del sistema (si está bloqueado). 2 Levante el seguro de liberación situado junto a la cerradura. 3 Gire el extremo izquierdo del bisel para extraerlo del panel anterior. 4 Desenganche el extremo derecho del bisel y tire del bisel para extraerlo del sistema. Ilustración 16-1.
Unidades de disco duro SEGURIDAD: Modelos AMT, E03J y E04J Los modelos AMT, E03J y E04J deben instalarse únicamente en lugares de acceso limitado según se define en cl 1.2.7.3 de CEI 60950-1:2005. Dependiendo de su configuración, la matriz puede llegar a admitir hasta 24 unidades de disco duro SAS de 2,5 pulgadas o hasta 12 unidades de disco duro SAS de 3,5 pulgadas en compartimentos de unidad internos.
Ilustración 16-3. Extracción e instalación de una unidad de disco duro de relleno de 2,5 pulgadas (solo MD3620f). 1 1 2 Unidad de disco duro de relleno 2 Lengüeta de liberación Instalación de una unidad de disco duro de relleno 1 Extraiga el bisel anterior, si está instalado. Ver “Extracción del bisel anterior” en la página 262. 2 Inserte la unidad de disco duro de relleno en el compartimiento para unidades hasta que esté completamente asentada.
2 Desde el software Modular Disk Storage Manager (MDSM), prepare la unidad para su extracción. Espere hasta que los indicadores de la unidad de disco duro del portaunidades indiquen que puede extraerse la unidad de forma segura. Para obtener información sobre cómo extraer unidades de intercambio directo, consulte la documentación de la controladora. Si la unidad está en línea, el indicador verde de actividad/fallo parpadea conforme se apaga la unidad.
Instalación de una unidad de disco duro PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
Extracción de una unidad de disco duro de un portaunidades de disco duro Extraiga los tornillos de los rieles deslizantes del portaunidades de disco duro y extraiga la unidad de disco duro del portaunidades. Ver Ilustración 16-5 para PowerVault MD3600f y Ilustración 16-6 para PowerVault MD3620f. Ilustración 16-5.
Ilustración 16-6.
Instalación de una unidad de disco duro en un portaunidades de disco duro 1 Inserte la unidad de disco duro en el portaunidades de disco duro con el extremo del conector de la unidad hacia atrás. Ver Ilustración 16-5. 2 Alinee los orificios para tornillos de la unidad de disco duro con el conjunto de la parte posterior de orificios del portaunidades de disco duro.
5 Conecte todos los cables de alimentación a la matriz. 6 Encienda la matriz y el servidor host. Ilustración 16-7.
Extracción de un módulo de la controladora RAID PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
Ilustración 16-8. Extracción e instalación de un módulo de controladora RAID 3 2 1 1 Módulo de la controladora RAID 3 Palanca de liberación 2 Lengüeta de liberación Instalación de un módulo de la controladora RAID AVISO: los cables de fibra óptica son frágiles. Si tuerce, retuerce, dobla o pinza los cables de fibra óptica puede causar daños en los cables, disminuir el rendimiento o perder datos. Para evitar daños, no retuerza, doble, pince ni pise los cables.
3 Conecte todos los cables al módulo de la controladora RAID. Si hay transceptores SFP y cables de fibra óptica, vuelva a instalarlos en los puertos correctos. 4 Si procede, actualice el firmware para el módulo de la controladora RAID. Para obtener información sobre el firmware más reciente, vaya a dell.com/support. Apertura del módulo de la controladora RAID PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados.
Ilustración 16-9. 1 1 Tornillos (2) 3 Hendidura Apertura y cierre del módulo de la controladora RAID 2 3 2 Módulo de la controladora RAID Cierre del módulo de la controladora RAID PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados.
Unidad de la batería de reserva del módulo de la controladora RAID Extracción de la unidad de la batería de reserva del módulo de la controladora RAID PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica.
Ilustración 16-10. Extracción e instalación de la unidad de la batería de reserva del módulo de la controladora RAID 1 2 1 Unidad de la batería de reserva 2 tornillo Instalación de la unidad de la batería de reserva del módulo de la controladora RAID PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados.
Módulo de suministro de energía/ventilador de enfriamiento NOTA: la matriz de almacenamiento incluye dos módulos integrados de suministro de energía/ventilador de enfriamiento de intercambio directo. La matriz admite dos módulos de suministro de energía/ventilador de enfriamiento de intercambio directo. Aunque haya una matriz que pueda funcionar temporalmente con un módulo, ambos módulos deben estar presentes para refrigerar correctamente el sistema.
Ilustración 16-11. Extracción e instalación del módulo de suministro de energía/ventilador de enfriamiento 1 2 3 1 Lengüeta de liberación 3 Asa del suministro de energía 2 Suministro de energía Instalación de un módulo de suministro de energía/ventilador de enfriamiento PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados.
2 Conecte el cable de alimentación al suministro de energía/ventilador de enfriamiento y enchufe el cable a la toma de corriente. 3 Sujete el cable de alimentación utilizando la tira. Ver Ilustración 16-12. Ilustración 16-12. Fijación del cable de alimentación 1 1 Tira de sujeción PRECAUCIÓN: cuando conecte el cable de alimentación, fíjelo con la tira de velcro.
3 Extraiga las unidades de disco duro de: – las ranuras 0 a 2 en PowerVault MD3600f – las ranuras 0 a 5 en PowerVault MD3620f Ver “Extracción de una unidad de disco duro” en la página 264. NOTA: marque cada unidad de disco duro con su posición de ranura según las vaya extrayendo. 4 Deslice el panel de control hasta sacarlo del chasis después de: – Empujar la lengüeta de liberación hacia la parte anterior de la matriz en PowerVault MD3600f. Ver Ilustración 16-13.
Ilustración 16-14. MD3620f Extracción e instalación del panel de control de PowerVault 1 2 1 Pata de liberación 2 Panel de control Instalación del panel de control 1 Alinee el panel de control con la ranura de la matriz. 2 Deslice el panel de control en la matriz hasta que: – La lengüeta de liberación quede colocada en PowerVault MD3600f. Ver Ilustración 16-13. – La pata de liberación quede colocada en PowerVault MD3620f. Ver Ilustración 16-14.
Plano posterior PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado. Lea y siga las instrucciones de seguridad entregadas con el producto.
Ilustración 16-15.
Ilustración 16-16. Extracción e instalación del plano posterior de PowerVault MD3600f 1 2 3 1 Tornillos (5) 3 Tornillo cautivo Ilustración 16-17.
Instalación del plano posterior 1 Alinee los orificios del plano posterior con los orificios de la matriz. 2 Apriete el tornillo cautivo que fija el plano posterior al chasis. Ver Ilustración 16-16 para PowerVault MD3600f o Ilustración 16-17 para PowerVault MD3620f. 3 Vuelva a colocar los tornillos que fijan el plano posterior al chasis. Ver Ilustración 16-16 para PowerVault MD3600f o Ilustración 16-17 para PowerVault MD3620f.
Administración: Instalación de componentes de matriz
Administración: Inventario de firmware Una matriz de almacenamiento está compuesta de diversos componentes, que pueden incluir módulos de la controladora RAID, discos físicos y módulos de administración de gabinetes (EMMs). Cada uno de estos componentes contiene firmware. Algunas versiones de firmware dependen de otras versiones de firmware. Para conseguir información acerca de todas las versiones de firmware de la matriz de almacenamiento, vea el inventario de firmware.
3 En Especificar nombre de archivo, introduzca un nombre para el archivo que vaya a guardar. También puede especificar otro disco físico y directorio si desea guardar el archivo en una ubicación distinta de la predeterminada. NOTA: el sufijo *.txt se agregará al nombre de archivo automáticamente si no especifica un sufijo para el nombre de archivo. 4 Haga clic en Guardar. Un archivo de texto ASCII que contiene el inventario de firmware se guardará en el directorio especificado.
Administración: Interfaces deI sistema Servicios de Microsoft Servicio de disco virtual El Servicio de disco virtual (VDS) de Microsoft es un componente del sistema operativo Windows. El componente VDS utiliza módulos de software específicos de terceros, denominados proveedores, para acceder y configurar recursos de almacenamiento de terceros como, por ejemplo, matrices de almacenamiento MD3600f.
El proveedor de hardware VSS utiliza el nombre del disco virtual de origen como prefijo para los nombres del disco virtual de repositorio y de instantánea. Los nombres de instantánea y de repositorio resultantes serán demasiado largos si el nombre del disco virtual de origen supera los 16 caracteres. VSS se conecta al servicio y lo utiliza para coordinar la creación de discos virtuales de instantánea en la matriz de almacenamiento.
• Los discos virtuales que se utilizan como discos virtuales de origen para instantáneas VSS deben tener nombres que no superen los 16 caracteres. El proveedor de hardware VSS utiliza el nombre del disco virtual de origen como prefijo para los nombres del disco virtual de repositorio y de instantánea. Los nombres de instantánea y de repositorio resultantes serán demasiado largos si el nombre del disco virtual de origen supera los 16 caracteres. NOTA: un volumen es otro término para disco virtual.
Administración: Interfaces deI sistema
Solución de problemas: software de la matriz de almacenamiento Rutina de inicio Observe y escuche durante la rutina de inicio de la matriz las indicaciones descritas en la Tabla 19-1. Para obtener una descripción de los indicadores del panel anterior y posterior, ver “Planificación: Acerca de la matriz de almacenamiento” en la página 25. Tabla 19-1. Indicaciones de la rutina de inicio Si observa/escucha Acción Mensajes de alerta Consulte la documentación de administración de almacenamiento.
Para iniciar la AMW, realice una de estas acciones: • En la ficha Dispositivos, en la vista Árbol o en la vista Tabla, haga doble clic en una matriz de almacenamiento. De manera alternativa, puede hacer clic con el botón derecho del mouse en una matriz de almacenamiento y seleccionar Administrar matriz de almacenamiento en el menú emergente. • En la ficha Configuración, seleccione Administrar una matriz de almacenamiento.
Tabla 19-2. Icono de estado Estado Icono Descripción No es compatible El nodo no es actualmente compatible con esta versión de MDSM. Software no compatible La matriz de almacenamiento está ejecutando un nivel de software que ya no es compatible con MDSM. En la vista Tabla, cada matriz de almacenamiento administrada aparece una vez, independientemente del número de archivos adjuntos que tenga en la vista Árbol.
Tabla 19-3. Iconos de estado adicionales Estado Icono Descripción Alertas no compatibles con un estado Requiere actualización No se admite la configuración de una alerta en una matriz de almacenamiento con el estado Requiere actualización. En este caso, la matriz de almacenamiento muestra tanto un estado Requiere actualización como un icono Alertas no compatibles en la vista Árbol. El icono Alertas no compatibles indica que la matriz de almacenamiento no se puede supervisar.
Tabla 19-3. Iconos de estado adicionales Estado Icono Agregando una matriz de almacenamiento Descripción El icono Contactando con la matriz de almacenamiento aparece en la vista Árbol y la vista Tabla hasta que se conozca el estado actual de cada matriz de almacenamiento administrada. El icono Contactando con la matriz de almacenamiento aparece en la barra de estado de la EMW y la barra de estado de la AMW y la información sobre herramientas muestra Contactando con la matriz de almacenamiento.
Para generar el informe de datos de soporte: 1 En la AMW, realice una de estas acciones: • Seleccione Avanzado→ Solución de problemas→ Datos de soporte→ Recopilar. • Seleccione la ficha Soporte y haga clic en Obtener información de soporte. Aparecerá la ventana Recopilar todos los datos de soporte. 2 Introduzca un nombre para el archivo de datos de soporte en Especificar nombre de archivo o haga clic en Examinar para navegar a un archivo previamente guardado para sobrescribir un archivo existente.
Para recopilar automáticamente los datos de paquete de soporte: 1 En la AMW, seleccione Avanzado→ Solución de problemas→ Datos de soporte→ Configuración automática. 2 Seleccione Recopilar automáticamente datos de soporte para eventos críticos. 3 Para cambiar la ubicación del paquete de soporte guardado, haga clic en Cambiar. Aparecerá la ventana Cambiar ubicación de carpeta; navegue hasta la carpeta correspondiente y haga clic en Aceptar.
3 Haga clic en Inicio. La recopilación de datos de disco físico se completa y se guarda en la ubicación que haya introducido. 4 Haga clic en Aceptar. Registro de eventos Puede utilizar el Visor del Registro de eventos para ver una lista detallada de los eventos que se producen en una matriz de almacenamiento. El registro de eventos se almacena en áreas reservadas de los discos de la matriz de almacenamiento.
3 Para guardar el registro de eventos, haga clic en Guardar como. Aparece el cuadro de diálogo Guardar eventos. 4 Vaya a la carpeta correspondiente, introduzca el nombre de archivo y haga clic en Guardar. 5 Para borrar todas las entradas del registro de eventos, haga clic en Borrar todo. 6 Para salir del registro de eventos, haga clic en Cerrar. Para obtener más información, consulte los temas de la Ayuda en línea de PowerVault Modular Disk Storage Manager.
Perfil de la matriz de almacenamiento El perfil de la matriz de almacenamiento proporciona una descripción de todos los componentes y propiedades de la matriz de almacenamiento. El perfil de la matriz de almacenamiento también ofrece la opción de guardar la información del perfil en un archivo de texto. También puede utilizar el perfil de la matriz de almacenamiento como ayuda durante la recuperación o como visión general de la configuración actual de la matriz de almacenamiento.
4 Para buscar el perfil de matriz de almacenamiento: a Haga clic en . b Escriba el término que desea buscar en el cuadro de texto Buscar. Si el término se encuentra en la ficha actual, se resaltará en la información del perfil de la matriz de almacenamiento. NOTA: la búsqueda se limita a la ficha actual. Si desea buscar el término en otras fichas, seleccione la ficha y vuelva a hacer clic en el botón Buscar. c Vuelva a hacer clic en el botón Buscar para buscar más apariciones del término.
Cómo ver las asociaciones lógicas Puede utilizar la opción Elementos lógicos asociados para ver las asociaciones lógicas entre diferentes discos virtuales de una matriz de almacenamiento. Para ver las asociaciones de discos virtuales de origen, discos virtuales de instantánea y discos virtuales de repositorio de instantánea: 1 En la AMW, seleccione la ficha Lógico o el panel Topología de la ficha Asignaciones. 2 Seleccione Ver→ Elementos lógicos asociados.
Aparece el cuadro de diálogo Ver componentes físicos asociados con un triángulo verde junto a los componentes físicos asociados con el nodo seleccionado. 3 Para cerrar el cuadro de diálogo Ver componentes físicos asociados, haga clic en Cerrar. Búsqueda de nodos Puede utilizar la opción Buscar para buscar un determinado nodo en las fichas Lógico, Físico o Asignaciones de la AMW.
6 Para buscar todos los nodos basados en su capacidad de disco virtual, realice estos pasos: a Seleccione Encontrar todos los discos virtuales con capacidad. b Escriba la capacidad en el cuadro GB. c Especifique que la capacidad coincidente sea menor, igual o mayor que la capacidad introducida en el cuadro GB. d Ver paso 8.
La opción Ir a sólo está disponible si la función Premium Instantánea o la función Premium Copia de disco virtual está habilitada o si existen actualmente discos virtuales de instantánea o copias de disco virtual en la matriz de almacenamiento. No se puede acceder a la opción Ir a desde la ficha Asignaciones de la Ventana Administración de matrices. 1 En la ficha Lógico de la AMW, seleccione uno de estos discos virtuales y vaya al paso indicado: • Disco virtual de instantánea; vaya al paso 2.
Recuperación de una condición de matriz de almacenamiento que no responde Una matriz de almacenamiento puede tener un estado No responde por diversas razones. Utilice el procedimiento de este tema para determinar una posible causa y solución. MDSM puede tardar hasta 5 minutos en detectar que una matriz de almacenamiento ha dejado de responder o vuelve a responder de nuevo.
8 Quite la matriz de almacenamiento con el estado No responde de la EMW, y seleccione Agregar matriz de almacenamiento para agregar de nuevo la matriz de almacenamiento. 9 Si la matriz de almacenamiento no vuelve al estado Óptimo, compruebe los cables Ethernet para asegurarse de que no haya daños visibles y de que están conectados de forma segura. 10 Asegúrese de que se hayan realizado las tareas de configuración de red adecuadas.
19 Si recientemente ha sustituido o agregado el módulo de la controladora RAID, reinicie el software de agente de contexto de host para que se reconozca el nuevo módulo de la controladora RAID. 20 Si el problema sigue existiendo, realice las modificaciones de host adecuadas, consulte con otros administradores para ver si se ha realizado una actualización de firmware en el módulo de la controladora RAID desde otra estación de administración de almacenamiento.
Ubicación de un disco físico Puede utilizar la opción Localizar disco físico para localizar físicamente e identificar uno o varios discos físicos en un gabinete de expansión activando los LEDs de disco físico. Para localizar el disco físico: 1 Seleccione la ficha Físico. 2 Seleccione los discos físicos que desee localizar. 3 Seleccione Disco físico→ Hacer parpadear→ Disco físico. Los LEDs de los discos físicos seleccionados parpadearán. 4 Cuando haya localizado los discos físicos, haga clic en Aceptar.
• Si tiene otros tipos de gabinetes de expansión, esta operación hará que parpadeen los LEDs correspondientes de todos los discos físicos del gabinete de expansión. Para localizar el gabinete de expansión: 1 Seleccione la ficha Físico. 2 Seleccione un disco físico del gabinete de expansión que desee localizar. 3 Seleccione Disco físico→ Hacer parpadear→ Gabinete de expansión. El LED o los LEDs del gabinete de expansión o los discos físicos se enciende o encienden.
Potencial de causar que una matriz no responda: la opción Captura del estado puede hacer que una matriz de almacenamiento deje de responder tanto al host como a la estación de administración de almacenamiento. Utilice esta opción sólo bajo la supervisión de un representante del servicio de asistencia técnica. 1 En la AMW, seleccione Avanzado→ Solución de problemas→ Capturar información de estado. 2 Lea esta información en el cuadro de diálogo Confirmar captura del estado, y escriba sí para continuar.
Utilidad SMrepassist SMrepassist (asistencia de replicación) es una utilidad basada en host para plataformas Windows. Esta utilidad se instala con MDSM. Utilice esta utilidad antes y después de crear una copia de disco virtual en un sistema operativo Windows, para asegurarse de que se han vaciado todos los datos residentes en la memoria para los sistemas de archivos del disco virtual de destino y que el controlador reconoce las firmas y las particiones del sistema de archivos.
NOTA: antes de iniciar cualquier procedimiento de recuperación, asegúrese de que el software de agente de contexto de host esté instalado y se está ejecutando. Si se inicia el host antes de conectarlo a la matriz de almacenamiento, el software de agente de contexto de host no será capaz de encontrar la matriz de almacenamiento. Si es así, asegúrese de que no haya ninguna conexión floja y reinicie el software de agente de host.
b Asegúrese de que la red pueda acceder al host mediante la ejecución del comando ping con la sintaxis siguiente: ping . Si la red puede acceder al host, continúe con el paso c. Si la red no puede acceder al host, vaya al paso d. c Elimine de MDSM el host cuyo estado indica que no responde y vuelva a agregarlo. Si el host vuelve al estado Óptimo, habrá finalizado este procedimiento. d Compruebe que el host reciba alimentación y que esté operativo.
c Examine todos los cables Ethernet para asegurarse de que no se han producido daños y que no hay ninguna conexión floja. d Asegúrese de que se hayan realizado las tareas de configuración de red aplicables (por ejemplo, que se hayan asignado las direcciones IP a cada controladora). 5 Asegúrese de que el firmware de la controladora sea compatible con MDSM en su estación de administración. Si se actualizó el firmware de la controladora, es posible que MDSM no tenga acceso a la matriz de almacenamiento.
Inicio o reinicio del software de Agente de contexto de host El módulo de software del agente de contexto de host es el componente de software que reside en el servidor o la estación de administración que se comunica con las matrices de almacenamiento serie MD3600f. El software SMagent se inicia automáticamente tras reiniciar el host. Windows Para reiniciar el software SMagent en Windows: 1 Haga clic en Inicio→ Configuración→ Panel de control→ Herramientas administrativas→ Servicios.
Copyright (C) 2009-2010 Dell, Inc. All rights reserved.
Solución de problemas: software de la matriz de almacenamiento
Solución de problemas: La matriz Seguridad para el usuario y la matriz PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
Solución de problemas de un transceptor SFP PRECAUCIÓN: cuando se encuentre trabajando con dispositivos sensibles a la estática, tome las precauciones necesarias para no dañar el producto por electricidad estática. NOTA: antes de seguir con esta sección, consulte el apartado “Working with SFP Modules” (Funcionamiento de módulos SFP) y “Fiber Optic Cables” (Cables de fibra óptica) en la Dell PowerVault MD3600f Deployment Guide (Guía de implementación de Dell PowerVault MD3600f) en dell.com/support.
• Si al menos un LED de velocidad FCIN está encendido para un determinado puerto, el transceptor SFP funcionará. Los LEDs de velocidad FCIN indican una velocidad de canal de 2 Gbps, 4 Gbps o 8 Gbps (ver “Indicaciones de enlace/velocidad de LED de canal de host” en la página 38). Asegúrese de que la velocidad indicada por los LEDs es la esperada.
En función del estado del LED, realice una de estas acciones: • Al menos uno de los LEDs FCIN de cada puerto está encendido. Ver paso 11. • Ambos LEDs FCIN de un gabinete del módulo de la controladora RAID de la matriz de almacenamiento MD de un determinado puerto están apagados. • Asegúrese de que la instalación del transceptor SFP se haya realizado correctamente. Vuelva a instalar el transceptor SFP si fuera necesario.
Solución de problemas del módulo de suministro de energía/ventilador de enfriamiento PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
2 Vuelva a colocar el suministro de energía; para ello, extráigalo y vuelva a instalarlo. Ver “Componentes del suministro de energía y del ventilador de enfriamiento” en la página 32. NOTA: después de instalar un suministro de energía, espere unos segundos hasta que la matriz lo reconozca y determine si funciona correctamente. Si el problema no se resuelve, ver “Obtención de ayuda” en la página 335.
Solución de problemas de los módulos de administración del gabinete de expansión PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
c Encienda los gabinetes de expansión y, a continuación, la matriz de almacenamiento y espere hasta que el sistema se haya reiniciado totalmente. d Encienda el servidor. e Compruebe el LED de estado de enlace. Si el LED de estado del enlace no está en verde, reemplace los cables. Si el problema no se resuelve, ver “Obtención de ayuda” en la página 335.
e Vuelva a instalar el módulo de la controladora RAID y espere 30 segundos. Ver “Instalación de un módulo de la controladora RAID” en la página 272. f Compruebe el LED de estado del módulo de la controladora RAID. g Vuelva a colocar el módulo de la controladora RAID h Encienda el servidor host. Si el problema no se resuelve, ver “Obtención de ayuda” en la página 335.
1 Compruebe el perfil de matriz de almacenamiento para asegurarse de que esté instalada la versión más actual del firmware. Para obtener más información, ver Matriz de compatibilidad en dell.com/support/manuals. 2 Quite la unidad de disco duro del sistema. Ver “Extracción de una unidad de disco duro” en la página 264. NOTA: debe asegurarse de haber comprobado los indicadores de la unidad de disco duro antes de quitar la unidad de disco duro defectuosa del sistema.
7 Compruebe los LEDs de todos los puertos cableados. Vuelva a colocar los cables de fibra óptica de los puertos en los que ambos LEDs estén apagados. Si el problema no se resuelve, ver “Obtención de ayuda” en la página 335. 8 Reinicie el servidor host. NOTA: debe apagar el servidor host antes de volver a colocar los cables en la matriz de almacenamiento o el gabinete de expansión. Si el problema no se resuelve, ver “Obtención de ayuda” en la página 335.
Solución de problemas de una matriz dañada PRECAUCIÓN: muchas de las reparaciones sólo pueden realizarlas los técnicos de servicio autorizados. El usuario debe llevar a cabo únicamente las tareas de solución de problemas y las reparaciones sencillas autorizadas en la documentación del producto o indicadas por el personal de servicio y asistencia en línea o telefónica. La garantía no cubre los daños ocasionados por reparaciones que Dell no haya autorizado.
Solución de problemas de módulos de la controladora RAID Condiciones Determinados eventos pueden hacer que falle y/o se apague un módulo de la controladora RAID. Los errores de PCI o de memoria ECC irrecuperables, o las condiciones físicas críticas pueden producir bloqueos. Si la matriz de almacenamiento RAID está configurada para acceso redundante y duplicación de caché, la controladora superviviente normalmente podrá recuperarse sin pérdida de datos ni necesidad de apagarse.
Errores de PCI El firmware de la matriz de almacenamiento puede detectar y sólo recuperarse de errores PCI cuando los módulos de la controladora RAID están configurados para redundancia. Si un disco virtual utiliza duplicación de caché, migrará tras error a su módulo de la controladora RAID par, que iniciará un vaciado de la caché sucia.
Obtención de ayuda Ubicación de la etiqueta de servicio de su sistema Su sistema está identificado por un Código de servicio rápido exclusivo y un número de Etiqueta de servicio. El Código de servicio rápido y la Etiqueta de servicio se encuentran en la parte anterior del sistema tirando de la etiqueta de información. Dell utiliza esta información para enrutar las llamadas de asistencia al personal adecuado.
Comentarios sobre la documentación Si tiene comentarios acerca de esta documentación, escriba a documentation_feedback@dell.com. De forma alternativa, haga clic en el enlace Feedback (Comentarios) en cualquiera de las páginas de documentación Dell, rellene el formulario y haga clic en Submit (Enviar) para enviar sus comentarios.
Índice A Administración de grupos de hosts, 103 Administración de identificadores de puerto de host, 108 Administrador de copias, 194 Asignación de host a disco virtual, 138 Asignaciones de host a disco virtual crear, 138, 142 modificar y quitar, 140 Asignaciones restringidas, 146 asistencia ponerse en contacto con Dell, 335 nivel de RAID de un grupo de discos, 143, 149 prioridad de modificación de disco virtual, 117 propiedad de la controladora del disco virtual, 141 propiedad de módulo de la controladora
Cómo iniciar o detener el Agente de contexto de host, 105 Cómo ponerse en contacto con Dell, 335 Componentes del suministro de energía y del ventilador de enfriamiento, 32 Componentes no exportables, 154 Configuración de batería, 95 Configuración de notificaciones de alerta SNMP, 93 Configurar acceso de host, 99 discos físicos de repuesto dinámico, 132 Contenido de la caja, 22 Copia de disco virtual objetivo, 63 origen, 63 D Descargas de firmware, 249 Disco virtual comprobación de coherencia, 53 copia fal
Discos físicos, discos virtuales y grupos de discos, 45 Discos virtuales de instantánea deshabilitar, 177 volver a crear, 179 Discos virtuales y grupos de discos, 48 E Elección de un tipo de disco físico adecuado, 122 Eliminación del acceso de host, 102 Equilibrio de carga, 66 Errores de soporte y sectores ilegibles, 259 Estados de disco virtual, 48 Estados de los discos físicos, 46 Event Monitor, 97 habilitar o deshabilitar, 98 Linux, 98 Windows, 98 Expansión de grupo de discos y discos virtuales, 152 Exp
EMM de relleno, 270 panel de control MD1200, 281 plano posterior, 285 unidad de disco duro, 266 Funciones e indicadores panel anterior, 26 G Grupo de discos crear, 112 expansión, 152 exportación, 154 exportar, 154 importar, 155 migración, 154 ubicar, 114 Grupo de hosts crear, 103 desplazamiento de un host, 104 eliminación de un grupo de host, 105 eliminación de un host, 104 Grupos de discos y discos virtuales crear, 111 instalar bisel anterior, 262 módulo de suministro de energía/ventilador de refrigerac
servicio de instantáneas de volumen, 289 Migración de disco virtual e itinerancia de disco itinerancia de disco, 60 migración de disco, 58 Módulo de la controladora RAID fallido, 193 Multirruta controladoras y rutas de acceso preferidas y alternativas, 65 P Panel de control extraer, 279 instalar, 281 Particionamiento de almacenamiento, 150 Patrones de los indicadores de la unidad de disco duro, 30 Plano posterior extraer, 282 Planos posteriores instalar, 285 N números de teléfono, 335 ponerse en contacto
R copia de disco virtual, 62 RAID, 49 cambiar nivel de grupo de discos, 149 RAID 0, 49 RAID 1, 50 RAID 10, 51 RAID 5, 51 RAID 6, 51 Uso, 50 Replicación remota acceso de host, 203 activación, 204, 211 administración, 210 creación, 213 discos virtuales, 205 Repuesto dinámico funcionamiento, 135 protección de la unidad, 135 repuestos dinámicos globales, 134 Repuesto dinámico y regeneración, 134 Ruta de acceso avanzada, 167 Ruta de acceso sencilla, 163 S Seguridad, 21 seguridad, 321 Seguridad de disco físico
conexiones externas, 324 enfriamiento, 326 error de inicio, 321 gabinete dañado, 332 gabinete mojado, 331 módulo de suministro de energía/ventilador de enfriamiento, 325 pérdida de comunicación, 321 unidades de disco duro, 329 Solución de problemas.
Índice