Dell EMC PowerVault MD 34XX/38XX 시리즈 스토리지 어레이 관리자 가이드 September 2018 개정 A06
참고, 주의 및 경고 노트: 참고"는 제품을 보다 효율적으로 사용하는 데 도움이 되는 중요 정보를 제공합니다. 주의: 주의사항은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: 경고는 재산 손실, 신체적 상해 또는 사망 위험이 있음을 알려줍니다. © 2012 - 2018Dell Inc. 또는 그 자회사. 저작권 본사 소유. Dell, EMC 및 기타 상표는 Dell Inc. 또는 자회사의 상표입니다. 기타 상표는 각 소유자의 상 표일 수 있습니다.
목차 장 1: 소개.......................................................................................................................................12 Dell EMC PowerVault Modular Disk Storage Manager................................................................................................... 12 UI............................................................................................................................................................................................ 12 엔터프라이즈 관리 창........
호스트 유형................................................................................................................................................................... 23 고급 기능............................................................................................................................................................................. 24 지원되는 스냅샷 기능 유형........................................................................................................................................
iSCSI 타겟 인증 변경..........................................................................................................................................................44 상호 인증 권한 입력...........................................................................................................................................................44 CHAP 암호 생성.................................................................................................................................................................
씬 가상 디스크 상태.....................................................................................................................................................64 비교 - 가상 디스크 및 복사 서비스 유형..................................................................................................................64 씬 가상 디스크의 롤백.................................................................................................................................................64 씬 가상 디스크 초기화.....................................
디스크 풀에서 물리적 디스크 찾기.................................................................................................................................87 디스크 풀 이름 변경...........................................................................................................................................................87 디스크 풀의 알림 구성...................................................................................................................................................... 88 할당 해제된 물리적 디스크를 디스크 풀에 추가..
스냅샷 롤백 시작........................................................................................................................................................ 105 스냅샷 이미지 롤백 재개...........................................................................................................................................105 스냅샷 이미지 롤백 취소...........................................................................................................................................106 스냅샷 롤백의 진행률 보기....................
가상 디스크 복사 실패............................................................................................................................................... 130 기본 RAID 컨트롤러 모듈 소유권...................................................................................................................................130 장애가 발생한 RAID 컨트롤러 모듈.............................................................................................................................. 130 복사 관리자.........................................
원격 복제 Premium 기능 활성화.................................................................................................................................... 145 원격 복제 비활성화.......................................................................................................................................................... 145 원격 복제 그룹...................................................................................................................................................................
호스트 컨텍스트 에이전트 소프트웨어 시작 또는 다시 재시작.............................................................................. 167 Windows에서 SMagent 소프트웨어 시작............................................................................................................... 167 Linux에서 SMagent 소프트웨어 시작...................................................................................................................... 167 장 19: 도움말 보기................................................................................................
1 소개 주의: 본 안내서에 설명된 절차를 수행하기 전에 중요한 안전 정보에 대해서는 안전성, 환경, 규제 정보 문서를 참조하십시오. 다음과 같은 MD Series 시스템은 최신 버전의 Dell PowerVault Modular Disk Manager(MDSM)에서 지원됩니다.
노트: 기본적으로 도구 모음 및 상태 표시줄은 표시되지 않습니다. 도구 모음 또는 상태 표시줄을 보려면 View(보기) > Toolbar(도구 모음) 또는 View(보기) > Status Bar(상태 표시줄)를 선택합니다. 엔터프라이즈 관리 창 EMW는 스토리지 어레이를 위한 수준 높은 관리 기능을 제공합니다. MD 스토리지 관리자를 시작하면 EMW가 표시됩니다. EMW에 는 다음과 같은 탭이 있습니다. • • Devices(장치) 탭 — 검색된 스토리지 어레이에 관한 정보를 제공합니다. Setup(설정) 탭 — 스토리지 어레이를 추가하고 경고를 구성하는 과정을 안내하는 초기 설정 작업을 제공합니다. Devices(장치) 탭에 왼쪽에는 검색된 스토리지 어레이, 식별되지 않은 스토리지 어레이, 스토리지 어레이의 상태 조건을 보여주는 Tree(트리) 뷰가 있습니다. 검색된 스토리지 어레이는 MD 스토리지 관리자에서 관리합니다.
• • • • RAID 컨트롤러 모듈 및 물리 디스크와 같은 하드웨어 구성요소에 관한 프로파일 정보를 봅니다. 가상 디스크 소유권을 변경하거나 RAID 컨트롤러 모듈을 온라인 또는 오프라인으로 전환하는 등 RAID 컨트롤러 모듈을 관리합니 다. 핫스페어를 할당하거나 물리 디스크를 찾는 등 물리 디스크를 관리합니다. 스토리지 어레이 성능을 모니터링합니다. AMW를 실행하려면 다음을 수행합니다. 1. EMW에서, Devices(장치) 탭에 있는 관련 스토리지 어레이를 마우스 오른쪽 단추로 클릭합니다. 선택한 스토리지의 컨텍스트 메뉴가 표시됩니다. 2. 컨텍스트 메뉴에서 Manage Storage Array(스토리지 어레이 관리)를 선택합니다. 선택한 스토리지 어레이의 AMW가 표시됩니다. 노트: 다음을 수행하여 AMW를 실행할 수도 있습니다. • EMW의 Devices(장치) 탭에 표시된 스토리지 어레이를 두 번 클릭합니다.
• • • • • • Dell EMC PowerVault MD3460/MD3860i/MD3860f 스토리지 어레이 소유자 매뉴얼 - 시스템 기능에 대한 정보를 제공하고 시스템 의 문제를 해결하는 방법 및 시스템 구성 요소를 설치하거나 교체하는 방법에 대해 설명합니다. 랙 설치 지침 — 시스템을 랙에 설치하는 방법을 설명합니다. 또한 이 설명서는 랙 솔루션과 함께 제공됩니다. Dell EMC PowerVault MD 시리즈 스토리지 어레이 관리자 가이드 - MDSM GUI를 사용한 시스템 구성 및 관리에 대한 정보를 제공 합니다. Dell EMC PowerVault MD 34XX/38XX 시리즈 스토리지 어레이 CLI 가이드 - MDSM CLI를 사용한 시스템 구성 및 관리에 대한 정 보를 제공합니다. Dell EMC PowerVault MD3460/MD3860i/MD3860f 스토리지 어레이 구축 가이드 - SAN 아키텍처에서 스토리지 시스템 배포에 대 한 정보를 제공합니다.
2 MD 시리즈 스토리지 어레이 정보 이 장에서는 Dell MD Series 스토리지 어레이를 구성하고 작동하는 데 유용한 스토리지 어레이 개념에 대해 설명합니다. 주제: • • • • • • • • • • • • • 물리적 디스크, 가상 디스크 및 디스크 그룹 디스크 풀 씬 가상 디스크 RAID 레벨 세그먼트 크기 가상 디스크 작업 디스크 그룹 작업 RAID 백그라운드 작업 우선 순위 가상 디스크 마이그레이션 및 디스크 로밍 고급 기능 다중 경로 소프트웨어 부하 분산 시스템 성능 모니터링 물리적 디스크, 가상 디스크 및 디스크 그룹 스토리지 어레이의 물리 디스크는 데이터를 위한 실제 스토리지 용량을 제공합니다. 스토리지 어레이에 데이터를 작성하려면 실제 스토리지 용량을 디스크 그룹 및 가상 디스크라고 하는 논리 구성요소에 구성해야 합니다. 디스크 그룹은 여러 가상 디스크가 생성되는 실제 디스크 세트입니다. 디스크 그룹 하나에서 지원되는 실제 디스크의 최대 개수는 다 음과 같습니다.
표 1. 물리적 디스크 상태 상태 모드 설명 Optimal(최적) Assigned(할당됨) 표시된 슬롯에 있는 물리 디스크가 디스크 그룹의 일부분으로 구성됩니다. Optimal(최적) Unassigned(할당되지 않음) 표시된 슬롯에 있는 물리 디스크가 사용되지 않았으며 구성에 사용 가능합니다. Optimal(최적) Hot Spare Standby(핫스페어 대기 중) 표시된 슬롯에 있는 물리 디스크가 핫스페어로 구성됩니다. Optimal(최적) Hot Spare in use(핫스페어 사용 중) 표시된 슬롯에 있는 물리 디스크가 디스크 그룹에서 핫스페어 로 사용되고 있습니다.
표 2. RAID 컨트롤러 가상 디스크 상태 (계속) 상태 설명 Offline(오프라인) 하나 이상의 구성원 디스크가 있는 가상 디스크가 액세스할 수 없는 상태입니다(장애 발생, 누락 또는 오프라인). 가상 디스크의 데이터 에 더 이상 액세스할 수 없습니다. Force Online(강제 온라인 설정) 스토리지 어레이가 가상 디스크를 Offline(오프라인) 상태에서 Optimal(최적) 상태로 강제 전환합니다. 일부 멤버 물리적 디스크를 사용할 수 없는 경우, 스토리지 어레이는 가상 디스크를 Degraded(성능 저하) 상태로 강제 전환합니다. 가상 디스크를 지원 할 수 있는 물리적 디스크 수가 충분한 경우에만 스토리지 어레이가 가상 디스크를 Online(온라인) 상태로 강제 전환할 수 있습니다. 디스크 풀 디스크 풀링을 사용하면 각 가상 디스크에서 물리 디스크 집합으로 데이터를 무작위로 분산시킬 수 있습니다.
RAID 0 주의: 스토리지 배열에 프리미엄 기능이 활성화되어 있더라도 RAID 0 구성에서 120개의 물리 디스크를 초과하는 가상 디스크 그 룹을 생성하지 마십시오. 물리 디스크가 120개를 초과하면 스토리지 배열이 불안정해질 수 있습니다. RAID 0은 디스크 스트라이핑을 사용하여 높은 데이터 처리량을 제공합니다. 특히 데이터 일관성이 필요하지 않은 환경에서 대규모 파일에 사용할 때 유용합니다. RAID 0은 데이터를 세그먼트로 나누고, 각 세그먼트를 별도의 물리 디스크에 작성합니다. 여러 물리 디 스크에 I/O 로드를 분산함으로써 I/O 성능을 현저히 향상시킵니다. RAID 0은 모든 RAID 레벨 중에서 최고의 성능을 제공하지만 데이 터 일관성은 부족합니다. RAID 0 구성에서는 물리 디스크 하나에 장애가 발생할 경우 모든 데이터가 유실될 수 있으므로 중요하지 않 은 데이터에만 이 옵션을 사용하십시오.
가상 디스크 작업 가상 디스크 초기화 모든 가상 디스크는 초기화해야 합니다. 초기화는 백그라운드에서 자동으로 수행되지만 Change Copy Priority(복사 우선 순위 변경) 옵션을 업데이트하여 수정할 수 있습니다. 이 변경은 초기화가 완료될 때까지 어레이의 성능에 영향을 줄 수 있습니다. 최대 4개의 가 상 디스크를 각각의 RAID 컨트롤러 모듈에서 동시에 초기화할 수 있습니다. 스토리지 어레이는 가상 디스크가 생성되어 정합성을 설정할 때 백그라운드 초기화를 실행하여 가상 디스크에 대해 전체 호스트 서 버 액세스를 허용합니다. 백그라운드 초기화는 RAID 0 가상 디스크에서 실행되지 않습니다. 백그라운드 초기화 속도는 MD Storage Manager가 제어합니다. 백그라운드 초기화 속도를 변경하려면 기존의 모든 백그라운드 초기화를 중지해야 합니다. 속도 변경은 백그 라운드 초기화가 자동으로 재시작될 때 구현됩니다.
디스크 그룹 작업 RAID 레벨 마이그레이션 사용자의 요구사항에 따라 RAID 레벨 간에 마이그레이션할 수 있습니다. 예를 들어, 스트라이프 세트(RAID 0)를 RAID 5 세트로 변환 하여 해당 세트에 내결함 특징을 추가할 수 있습니다. MD 스토리지 관리자는 사용자가 적절한 RAID 레벨을 선택할 수 있도록 RAID 특 성에 대한 정보를 제공합니다. 시스템이 실행되고 있는 동안 다시 부팅하지 않고도 RAID 레벨 마이그레이션을 수행할 수 있으므로 데 이터 가용성을 유지할 수 있습니다. 세그먼트 크기 마이그레이션 세그먼트 크기는 스토리지 배열이 다음 물리 디스크에 데이터를 작성하기 전에 가상 디스크의 물리 디스크에 작성하는 데이터의 양 (KB)을 나타냅니다. 세그먼트 크기에 유효한 값은 8 KB, 16 KB, 32 KB, 64 KB, 128 KB 및 256 KB입니다. 동적 세그먼트 크기 마이그레이션을 통해 지정된 가상 디스크의 세그먼트 크기가 변경될 수 있습니다.
기존 디스크 그룹 프로세스에서 중복 RAID 컨트롤러 모듈에 장애가 발생하는 경우, 장애가 발생한 컨트롤러의 프로세스는 피어 컨트 롤러로 이전됩니다. 피어 컨트롤러에 활성 상태의 디스크 그룹 프로세스가 있을 경우 이전된 프로세스는 일시 중지됨 상태가 됩니다. 일시 중지된 프로세스는 피어 컨트롤러의 활성 프로세스가 완료되거나 중지되면 재개됩니다. 노트: 기존의 활성 프로세스가 없는 컨트롤러에서 디스크 그룹을 시작하려고 시도하면, 디스크 그룹의 첫 번째 가상 디스크가 다 른 컨트롤러의 소유이고 다른 컨트롤러에 활성 프로세스가 있는 경우 시작 시도에 실패합니다. RAID 백그라운드 작업 우선 순위 스토리지 배열은 다음과 같은 RAID 작업에 대한 일반적인 구성 가능한 우선순위를 지원합니다.
노트: 대상 스토리지 어레이에 기존 실제 디스크가 포함되어 있을 때 마이그레이션하는 디스크 그룹 및 가상 디스크가 올바르게 인식되도록 하려면, 핫 가상 디스크 마이그레이션을 사용합니다. 가상 디스크 마이그레이션을 시도할 때 다음과 같은 권장사항을 따르십시오. • • • • 마이그레이션을 위해 대상 어레이로 물리적 디스크 이동 - 핫 가상 디스크 마이그레이션을 수행하는 동안 물리적 디스크를 대상 스토리지 어레이에 삽입한 경우, 다음 물리적 디스크를 삽입하기 전에 삽입된 물리적 디스크가 MD Storage Manager에 표시될 때 까지 기다리거나 30초간 기다립니다(먼저 발생한 순서로). 노트: 물리 디스크 삽입 절차에 간격이 없는 경우, 스토리지 배열은 불안정한 상태가 될 수 있고 관리성 손실이 일시적으로 발 생될 수 있습니다.
고급 기능 RAID 인클로저는 몇 가지 고급 기능을 지원합니다. • • 가상 디스크 스냅샷 가상 디스크 복사 노트: 위에 나열된 프리미엄 기능은 별도로 활성화해야 합니다. 이러한 기능을 구매하면 기능 활성화에 대한 지침이 포함된 활성 화 카드가 함께 배송됩니다. 지원되는 스냅샷 기능 유형 다음 유형의 가상 디스크 스냅샷 프리미엄 기능이 MD 스토리지 어레이에서 지원됩니다. • 다중 시점(PiT: point-in-time) 그룹을 사용하는 스냅샷 가상 디스크 — 이 기능은 스냅샷 그룹, 스냅샷 이미지 및 일관성 그룹도 지 원합니다. 자세한 내용은 프리미엄 기능--스냅샷 가상 디스크를 참조하십시오. 스냅샷 가상 디스크, 스냅샷 이미지 및 스냅샷 그룹 스냅샷 이미지는 특정 시점(poin-in-time)에 생성된 연결된 기본 가상 디스크의 콘텐츠에 대한 논리 이미지입니다.
가상 디스크 복구 Edit host server-to-virtual disk mappings(호스트 서버-가상 디스크 매핑 편집) 기능을 사용하여 백업 가상 디스크에서 데이터를 복구 할 수 있습니다. 이 기능을 사용하면 호스트 서버에서 원래 소스 가상 디스크의 매핑을 해제한 다음 백업 가상 디스크를 동일한 호스 트 서버에 매핑할 수 있습니다. 소스 가상 디스크에 대한 액세스를 제공하는 데 사용된 LUN을 기록해 두십시오. 대상(백업) 가상 디스크의 호스트 서버-가상 디스크 매핑을 정의할 때 이 정보가 필요합니다. 또한 가상 디스크 복구 절차를 시작하기 전에 소스 가상 디스크에 대한 모든 I/O 활동을 중지 해야 합니다. 다중 경로 소프트웨어 호스트 서버에 상주하는 다중 경로 소프트웨어(장애 조치 드라이버라고도 함)는 호스트 서버와 스토리지 어레이 간에 중복 데이터 경 로를 관리할 수 있도록 하는 소프트웨어입니다.
모듈의 모든 경로를 I/O 활동에 대해 동등하게 처리합니다. 보조 RAID 컨트롤러 모듈의 경로는 소유권이 변경될 때까지 무시됩니 다. 기본적으로 라운드 로빈 정책에 대해 데이터 경로가 동일하다고 가정합니다. 혼합 호스트가 지원되는 경우, 데이터 경로마다 대역폭 또는 데이터 전송 속도가 다를 수 있습니다. Least queue depth with subset(서브셋에 최소 큐 깊이) - 서브셋에 최소 큐 깊이 정책은 최소 I/O 또는 최소 요청 정책이라고도 합 니다. 이 정책은 최소 미해결 I/O 요청이 큐에 대기중인 데이터 경로에 다음 I/O 요청을 전달합니다. 이 정책의 경우, I/O 요청은 단 순히 큐에서 명령에 해당합니다. 명령의 유형 또는 명령과 관련된 블록의 수는 고려되지 않습니다. 서브셋에 최소 큐 깊이 정책은 규모가 큰 블록 요청과 규모가 작은 블록 요청을 동등하게 처리합니다. 선택된 데이터 경로는 가상 디스크를 소유하는 RAID 컨트 롤러 모듈의 경로 그룹에 있는 경로 중 하나입니다.
• • • 백그라운드 모니터링 프로세스가 7일 동안 데이터를 샘플링하고 저장합니다. 이 기간 동안 모니터링되는 객체가 변경되면 해당 객체에는 전체 7일에 걸쳐 완벽한 데이터 지점 세트가 포함되지 않습니다. 예를 들어 가상 디스크 세트가 생성됨, 삭제됨, 매핑됨, 매핑 해제됨으로 변경되거나, 물리적 디스크가 추가, 제거되거나 실패할 수 있습니다. 성능 데이터는 I/O 호스트가 표시되는(매핑된) 가상 디스크, 스냅샷 그룹 저장소 가상 디스크 및 일관성 그룹 저장소 가상 디스크 에 대해서만 수집되고 표시됩니다. 복제 저장소 가상 디스크의 데이터는 수집되지 않습니다. RAID 컨트롤러 모듈 또는 스토리지 어레이의 보고된 값은 모든 가상 디스크의 보고된 값의 합계보다 클 수 있습니다. RAID 컨트롤 러 모듈 또는 스토리지 어레이의 보고된 값에는 호스트 I/O 및 스토리지 어레이의 내부 I/O(메타데이터 읽기 및 쓰기) 둘 다 포함 되며 가상 디스크의 보고된 값에는 호스트 I/O만 포함됩니다.
표 4. 성능 데이터 의미 (계속) 성능 데이터 성능 조정에 대한 의미 캐시 적중률이 높을수록 I/O 속도도 높아집니다. 쓰기 캐싱이 활 성화되면 비활성화 상태에 비해 I/O 속도가 높아집니다. 개별 가 상 디스크에 쓰기 캐싱을 활성화할지 결정할 때는 현재 IOPS와 최대 IOPS를 확인하십시오. 임의 I/O 패턴이 아닌 순차 I/O 패턴 의 속도가 높습니다. I/O 패턴과 관계없이, 쓰기 캐싱을 활성화하 면 I/O 속도를 최대화하고 응용프로그램 응답 시간을 단축시킬 수 있습니다. 읽기/쓰기 캐싱 및 성능에 대한 자세한 내용은 이 항목 마지막 부분에 나열된 관련 항목을 참조하십시오. MB/초 IO/초를 참조하십시오. I/O 대기 시간, 밀리초 대기 시간은 특정 실제 디스크 및 특정 가상 디스크의 I/O 활동을 모니터링할 때 유용하며 병목 현상이 있는 실제 디스크를 식별하 는 데 도움이 됩니다. 실제 디스크의 유형과 속도는 대기 시간에 영향을 줍니다.
1. 대시보드를 보려면 어레이 관리 창(AMW)에서 Performance(성능) 탭을 클릭합니다. 6개의 그래프를 보여주는 Performance(성능) 탭이 열립니다. 2. 단일 성능 그래프를 보려면 어레이 관리 창(AMW)에서 Monitor(모니터) > Health(상태) > Monitor Performance(성능 모니터) > Real-time performance monitor(실시간 성능 모니터) > View graphical(그래픽 보기)을 선택합니다. View Real-time Graphical Performance Monitor(실시간 그래픽 성능 모니터 보기) 대화상자가 열립니다. 3. Select metric(메트릭 선택) 드롭다운 목록에서, 확인할 성능 데이터를 선택합니다. 메트릭을 하나만 선택할 수 있습니다. 4. Select an object(s)(개체 선택) 목록에서, 성능 데이터를 볼 개체를 선택합니다. 하나의 그래프에서 모니터링할 개체를 최대 5개 선택할 수 있습니다.
사용 가능한 메트릭에는 현재 값, 최소 값, 최대 값, 평균 값이 있습니다. 현재 값은 가장 최근에 수집된 데이터 지점입니다. 최소, 최대, 평균 값은 성능 모니터링 시작을 기준으로 결정됩니다. 실시간 성능 모니터링의 경우, 어레이 관리 창(AMW)이 열리는 시점이 시작 시점입니다. 배경 성능 모니터링의 경우, 배경 성능 모니터링이 시작되는 시점이 시작 시점입니다. 스토리지 어레이 수준에서 성능 지표는 RAID 컨트롤러 모듈의 지표 합계입니다. RAID 컨트롤러 모듈 및 디스크 그룹의 지표는 디스크 그룹/소유 RAID 컨트롤러 모듈 수준에서 각 가상 디스크에 대해 검색된 데이터를 집계하여 계산됩니다. RAID 컨트롤러 모듈 또는 스 토리지 어레이의 보고된 값은 모든 가상 디스크의 보고된 값의 합계보다 클 수 있습니다.
• • Click the Performance(성능) 탭을 클릭하고 Launch real-time textual performance monitor(실시간 텍스트 성능 모니터 실행) 링크를 클릭합니다. Monitor(모니터) > Health(상태) > Monitor Performance(성능 모니터) > Real-time performance monitor(실시간 성능 모 니터) > View textual(텍스트 보기)을 선택합니다. View Real-time Textual Performance Monitor(실시간 텍스트 성능 모니터 보기) 대화상자가 표시됩니다. 2. 모니터링할 개체와 샘플링 간격을 선택하려면 Settings(설정) 단추를 클릭합니다. Settings(설정) 단추는 실시간 텍스트 성능 모니터가 시작되지 않았을 때만 사용할 수 있습니다. Performance Summary Settings(성능 요약 설정) 대화 상자가 표시됩니다. 3.
현재 백그라운드 성능 모니터 세션에 대한 정보 보기 이 작업을 수행하기 전에 배경 성능 모니터링이 진행 중인지 확인하십시오. View Current Background Performance Monitor(현재 배경 성능 모니터 보기) 대화상자에서 Stop(중지) 링크 옆에 In Progress(진행 중) 아이콘이 있으면 배경 성능 모니터링이 진행 중 인 것입니다. 1. 어레이 관리 창(AMW)에서 Performance(성능) 탭을 클릭합니다. 2. Launch background performance monitor(배경 성능 모니터 실행) 링크를 클릭합니다. View Current Background Performance Monitor(현재 배경 성능 모니터 보기) 대화상자가 나타납니다. 3. 포인터를 Stop(중지) 링크 위에 올려 놓습니다. 배경 성능 모니터링이 시작된 시간, 배경 성능 모니터링이 진행된 기간, 샘플링 간격을 보여주는 툴팁이 나타납니다.
99,999를 초과하면 1,000,000(백만) 단위로 표시됩니다. 9,999,000보다 크고 100,000,000보다 작은 값(예: 12,300,000=12.3)은 소수점 으로 표시됩니다. 1. 어레이 관리 창(AMW)에서 Performance(성능) 탭을 클릭합니다. 2. Launch background performance monitor(배경 성능 모니터 실행) 링크를 클릭합니다. View Current Background Performance Monitor(현재 배경 성능 모니터 보기) 대화상자가 나타납니다. 3. Launch saved background performance monitor(저장된 배경 성능 모니터 실행) 링크를 클릭합니다. Load Background Performance(배경 성능 불러오기) 대화상자가 나타납니다. 4. 열려는 .csv 파일을 찾아 Open(열기)을 클릭합니다.
3 스토리지 어레이 검색 및 관리 다음 두 가지 방법으로 스토리지 어레이를 관리할 수 있습니다. • • 대역 외 관리 대역 내 관리 EMW(Enterprise Management Window)는 MDSM(Modular Disk Storage Manager)을 열 때 로드되는 첫 번째 페이지입니다. 이 페이지 에서 인밴드(In-Band) 및 아웃오브밴드(Out-of-Band) 연결을 통해 MD3 스토리지 어레이를 검색 및 관리하고 어레이에 연결할 수 있 습니다. 들여쓰기된 스토리지 이름은 검색된 어레이이며 사용자는 운영자가 선택한 어레이를 관리할 수 있습니다. 주제: • • • • • • • 대역 외 관리 대역 내 관리 스토리지 어레이 스토리지 어레이 설정 알림 구성 배터리 설정 스토리지 어레이 RAID 컨트롤러 모듈 클럭 설정 대역 외 관리 대역외 관리 방법에서, 데이터는 명령 및 이벤트와 별도로 처리됩니다.
액세스 가상 디스크 MD Series 스토리지 어레이의 각 RAID 컨트롤러 모듈은 액세스 가상 디스크라고 하는 특수 가상 디스크를 유지 관리합니다. 호스트에이전트 소프트웨어는 액세스 가상 디스크를 사용하여 대역 내 관리형 스토리지 어레이에서 스토리지 관리 스테이션과 RAID 컨트 롤러 모듈 간의 관리 요청 및 이벤트 정보를 전달합니다. 액세스 가상 디스크는 응용 프로그램 데이터 스토리지에 사용할 수 없으며 전체 가상 디스크, 가상 디스크 그룹 또는 가상 디스크 쌍을 삭제하지 않고는 제거할 수 없습니다. 기본 LUN은 31입니다. 스토리지 어레이 스토리지 어레이를 MD 스토리지 관리자에 추가해야 스토리지 어레이가 최적화되도록 설정할 수 있습니다. 노트: EMW에서만 스토리지 어레이를 추가할 수 있습니다. 다음과 같은 작업을 수행할 수 있습니다. • • 스토리지 어레이를 자동으로 검색합니다. 스토리지 어레이를 수동으로 추가합니다.
• • AMW에서, Setup(설정) 탭을 선택하고 Rename Storage Arrays(스토리지 배열 이름 변경)를 선택합니다. EMW에서, 배열에 해당하는 아이콘을 마우스 오른쪽 단추로 클릭한 다음 Rename(이름 변경)을 선택합니다. 스토리지 어레이 설정 초기 설정 작업 목록이 AMW의 Setup(설정) 탭에 표시됩니다. Initial Setup Tasks(초기 설정 작업) 영역에 설명된 작업을 사용하여 기본 단계를 완료합니다. Initial Setup Tasks(초기 설정 작업) 목록을 사용하여 초기에 스토리지 배열을 설정하고 다음과 같은 작업을 수행합니다. • • • • • • • 스토리지 배열 찾기 — 시스템 식별 표시등을 켜서 네트워크에 있는 스토리지 배열의 실제 위치를 찾습니다. 스토리지 배열에 새 이름 부여 - 각 스토리지 배열을 식별하는 고유한 이름을 사용합니다. 스토리지 배열 암호 설정 - 암호를 사용하여 무단 액세스로부터 스토리지 배열이 보호되도록 구성합니다.
• EMW의 Devices(장치) 탭 Tree(트리) 뷰에서, 원하는 배열 아이콘을 마우스 오른쪽 단추로 클릭하고 Rename(이름 변경)을 선택합니다. Rename Storage Array(스토리지 배열 이름 변경) 대화상자가 표시됩니다. 2. 스토리지 배열의 새 이름을 입력합니다. 노트: 임의의 이름이나 나중에 의미가 상실되는 이름은 사용하지 마십시오. 3. 확인을 클릭합니다. 스토리지 배열의 이름 변경 결과에 대해 경고하는 메시지가 표시됩니다. 4. Yes(예)를 클릭합니다. 새 스토리지 배열 이름이 EMW에 표시됩니다. 5. 추가 스토리지 배열의 이름을 지정하거나 변경하려면 1단계 - 4단계를 반복하십시오. 암호 설정 암호를 사용하여 각 스토리지 배열을 구성함으로써 무단 액세스로부터 보호할 수 있습니다. MD 스토리지 관리자는 가상 디스크가 생 성되거나 삭제되는 경우와 같이 스토리지 배열 구성을 변경하려는 시도가 있을 때 암호를 입력하라는 메시지를 표시합니다.
노트: 설명의 문자 수는 60자를 초과하지 않아야 합니다. 4. 확인을 클릭합니다. 이 옵션을 사용하면 Table(표) 뷰에서 설명이 업데이트되고 사용자의 로컬 스토리지 관리 스테이션 파일 시스템에 저장됩니다. 이 설명은 다른 스토리지 관리 스테이션을 사용하는 관리자에게는 표시되지 않습니다. 스토리지 어레이 제거 특정 스토리지 관리 스테이션에서 스토리지 배열을 더 이상 관리하지 않으려는 경우, 관리형 배열 목록에서 스토리지 배열을 제거할 수 있습니다. 스토리지 배열을 제거해도 스토리지 배열이나 해당 데이터에는 영향을 주지 않습니다. 스토리지 배열을 제거하면 EMW 의 Devices(장치) 탭에 표시되는 스토리지 배열 목록에서만 스토리지 배열이 제거됩니다. 스토리지 배열을 제거하려면 다음을 수행합니다. 1. EMW에서, Devices(장치) 탭을 선택하고 적절한 관리형 스토리지 배열을 선택합니다. 2. Edit(편집) > Remove(제거) > Storage Array(스토리지 배열)를 선택합니다.
1. AMW에서, Storage Array(스토리지 어레이) > Change(변경) > Cache Settings(캐시 설정)를 선택합니다. Change Cache Settings(캐시 설정 변경) 창이 표시됩니다 2. Start demand cache flushing(요청 시 캐시 플러시 시작)에서, 캐시 플러시가 시작되도록 캐시에 기록되지 않은 데이터의 백분 율을 선택하거나 입력합니다. 3. 적절한 Cache block size(캐시 블록 크기)를 선택합니다. 파일-시스템 또는 데이터베이스-응용프로그램에 사용하려면 크기가 작은 캐시를 선택하는 것이 좋습니다. 크기가 큰 캐시는 멀 티미디어와 같은 순차적 I/O를 생성하는 응용프로그램용으로 적합합니다. 4. 선택한 스토리지 어레이에 암호를 설정한 경우 Enter Password(암호 입력) 대화상자가 표시됩니다. 스토리지 어레이의 현재 암 호를 입력하고 OK(확인)를 클릭합니다.
이메일 알림 구성 1. EMW에서 다음 작업 중 하나를 수행하여 Configure Alerts(경고 구성) 대화상자를 엽니다. • Devices(장치) 탭에서, 노드를 선택한 다음 메뉴 표시줄에서 Edit(편집) > Configure Alerts(경고 구성)를 선택합니다. 3단계 로 이동합니다. 노트: 이 옵션을 사용하면 호스트에 연결된 모든 스토리지 어레이에 대해 경고를 설정할 수 있습니다. • Setup(설정)에서, Configure Alerts(경고 구성)를 선택합니다. 2단계로 이동합니다. 2. 다음 라디오 단추 중 하나를 선택하여 경고 레벨을 지정합니다. • All storage arrays(모든 스토리지 배열) — 모든 스토리지 배열에서 발생하는 이벤트에 대한 전자 우편 경고를 보내려면 이 옵션을 선택합니다. • An individual storage array(개별 스토리지 배열) — 지정된 스토리지 배열에서만 발생하는 이벤트에 대한 전자 우편 경고를 보내려면 이 옵션을 선택합니다.
• • • • 작업할 전자 우편 주소에 대해 SMTP 메일 서버 이름과 전자 우편 보내는 사람 주소를 입력합니다. 이전에 구성한 전자 우편 주소가 Configured e-mail addresses(구성된 전자 우편 주소) 영역에 나타나는지 확인합니다. 정규화된 전자 우편 주소를 사용합니다(예: name@mycompany.com). OK(확인)를 클릭하기 전에 여러 개의 전자 우편 주소를 구성합니다. SNMP 알림 구성 다음에서 시작되는 SNMP 경고를 구성할 수 있습니다. • • 스토리지 어레이 이벤트 모니터 1. EMW에서 다음 작업 중 하나를 수행하여 Configure Alerts(경고 구성) 대화상자를 엽니다. • Devices(장치) 탭에서, 노드를 선택한 다음 메뉴 표시줄에서 Edit(편집) > Configure Alerts(경고 구성)를 선택합니다. 3단계 로 이동합니다. 노트: 이 옵션을 사용하면 호스트에 연결된 모든 스토리지 어레이에 대해 경고를 설정할 수 있습니다.
이전에 구성한 SNMP 주소가 Configured SNMP addresses(구성된 SNMP 주소) 영역에 나타납니다. 3. Community Name(커뮤니티 이름) 텍스트 상자에 커뮤니티 이름을 입력합니다. 최대 20자의 커뮤니티 이름을 사용할 수 있습니다. 4. Trap destination(트랩 대상) 텍스트 상자에 트랩 대상을 입력하고 Add(추가)를 클릭합니다. 호스트 이름, IPv4 주소 또는 IPv6 주소를 입력할 수 있습니다. 5. (선택사항) SNMP 경고가 올바르게 구성되었는지 확인하기 위해 테스트 메시지를 보낼 수 있습니다. Configured SNMP addresses(구성된 SNMP 주소) 영역에서 테스트할 SNMP 대상을 선택하고 Test(테스트)를 클릭합니다. 테스트 메시지가 SNMP 주소로 전송됩니다. 확인 결과 및 오류가 표시된 대화상자가 나타납니다. 커뮤니티 이름을 선택하지 않으 면 Test(테스트) 단추를 사용할 수 없습니다. 6. 확인을 클릭합니다.
No(아니오) – Configured SNMP addresses(구성된 SNMP 주소) 표의 Send Authentication Failure Trap(인증 장애 트랩 보내 기) 열에 해당하는 확인란을 선택 취소합니다. 8. (선택사항) SNMP 경고가 올바르게 구성되었는지 확인하기 위해 테스트 메시지를 보낼 수 있습니다. Configured SNMP addresses(구성된 SNMP 주소) 영역에서 테스트할 SNMP 대상을 선택하고 Test(테스트)를 클릭합니다. 확인 결과 및 오류가 표시 된 대화상자가 나타납니다. 커뮤니티 이름을 선택하지 않으면 Test(테스트) 단추를 사용할 수 없습니다. 9. 확인을 클릭합니다. 경고가 설정된 Tree(트리) 뷰에서 각 노드 옆에 경고 아이콘이 표시됩니다. • 배터리 설정 스마트 BBU(Battery Backup Unit)는 런사이클을 수행할 수 있습니다. 스마트 BBU 모듈에는 배터리, 배터리 잔량 게이지, 배터리 충전 기가 포함되어 있습니다.
4 iSCSI 사용 노트: 다음 섹션에서는 iSCSI 프로토콜을 사용하는 MDxx0i 스토리지 어레이와만 관련이 있습니다. 주제: iSCSI 타겟 인증 변경 상호 인증 권한 입력 CHAP 암호 생성 iSCSI 타겟 ID 변경 iSCSI 타겟 검색 설정 변경 iSCSI 호스트 포트 구성 고급 iSCSI 호스트 포트 설정 iSCSI 세션 보기 또는 종료 iSCSI 통계 보기 및 기준 통계 설정 호스트 토폴로지 편집, 제거 또는 이름 바꾸기 • • • • • • • • • • iSCSI 타겟 인증 변경 iSCSI 대상 인증을 변경하려면 다음을 수행합니다. 1. AMW에서 Setup(설정) 탭을 선택합니다. 2. Manage iSCSI Settings(iSCSI 설정 관리)를 선택합니다. Manage iSCSI Settings(iSCSI 설정 관리) 창이 표시되고 Target Authentication(대상 인증) 탭이 기본적으로 선택됩니다. 3. 인증 설정을 변경하려면 다음과 같이 선택합니다.
3. Remote Initiator Configuration(원격 초기자 구성) 탭을 선택합니다. 4. Select an Initiator(초기자 선택) 영역에서 초기자를 선택합니다. 초기자 세부사항이 표시됩니다. 5. CHAP Secret(CHAP 암호)를 클릭하여 표시되는 대화상자에 초기자 CHAP 권한을 입력합니다. 6. 확인을 클릭합니다. 7. Manage iSCSI Settings(iSCSI 설정 관리) 창에서 OK(확인)를 클릭합니다. CHAP 암호 생성 인증 방법을 설정할 때 CHAP 암호를 생성할 수 있도록 선택할 수 있습니다. CHAP 암호는 초기자 및 대상에서 인식하는 암호입니다. 상호 인증 방법으로 스토리지 배열을 구성하는 경우, 호스트 서버 iSCSI 초기자에 정의된 것과 동일한 CHAP 암호를 입력해야 하고 대 상 스토리지 배열에 연결되는 모든 iSCSI 초기자에 구성해야 하는 대상(스토리지 배열)에 CHAP 암호를 정의해야 합니다.
노트: 별칭에 최대 30자를 입력할 수 있습니다. 별칭에는 문자, 숫자와 특수 문자인 밑줄(_), 빼기 기호(-), 파운드 부호(#)를 사용할 수 있습니다. 다른 특수 문자는 사용할 수 없습니다. 노트: Red Hat Enterprise Linux 5 및 SUSE Linux Enterprise Server 10 SP 1에서 사용되는 Open iSCSI는 대상 별칭 사용 을 지원하지 않습니다. iSCSI 타겟 검색 설정 변경 iSCSI 대상 검색 설정을 변경하려면 다음을 수행합니다. 1. AMW에서 Setup(설정) 탭을 선택합니다. 2. Manage iSCSI Settings(iSCSI 설정 관리)를 선택합니다. Manage iSCSI Settings(iSCSI 설정 관리) 창이 표시됩니다. 3. Target Discovery(대상 검색) 탭을 선택합니다. 4. Use iSNS(iSNS 사용)를 선택하여 iSCSI 대상 검색을 활성화합니다. 5.
• 설정을 수동으로 구성하려면 Specify configuration(구성 지정) 옵션을 선택합니다. 노트: 자동 구성 방법을 선택하면 IPv4 설정용 DHCP가 사용되어 자동으로 구성을 가져옵니다. IPv6 설정과 마찬가지로 하 위 네트워크에 있는 MAC 주소 및 IPv6 라우터를 기반으로 구성을 자동으로 가져옵니다. 8. Advanced IPv4 Settings(고급 IPv4 설정) 및 Advanced IPv6 Settings(고급 IPV6 설정)를 클릭하여 가상 근거리 통신망(VLAN) 지원 및 이더넷 우선 순위를 구성할 수 있습니다. 9. Advanced Port Settings(고급 포트 설정)를 클릭하여 TCP listening port settings(TCP 수신 대기 포트 설정) 및 Jumbo frame(점보 프레임) 설정을 구성할 수 있습니다. 10.
a. 종료할 세션을 선택한 다음, End Session(세션 종료)을 클릭합니다. End Session confirmation(세션 종료 확인) 창이 표시됩니다. b. Yes(예)를 클릭하여 iSCSI 세션 종료를 확인합니다. 노트: 세션을 종료하면 해당 연결이 호스트와 스토리지 어레이 사이의 링크가 종료되며, 스토리지 어레이의 데이터를 더 이 상 사용할 수 없습니다. 노트: MD 스토리지 관리자를 사용하여 세션을 수동으로 종료하면 iSCSI 초기자 소프트웨어는 스토리지 어레이와의 종료된 연결을 재설정하려고 자동으로 시도합니다. 이로 인해 오류 메시지가 표시됩니다. iSCSI 통계 보기 및 기준 통계 설정 iSCSI 통계를 보고 기준 통계를 설정하려면 다음을 수행합니다. 1. AMW 메뉴 표시줄에서 Monitor(모니터) > Health(상태) > iSCSI Statistics(iSCSI 통계)를 선택합니다. View iSCSI Statistics(iSCSI 통계 보기) 창이 표시됩니다. 2.
호스트, 호스트 그룹, 호스트 토폴로지에 관한 자세한 내용을 보려면 호스트 정보를 참조하십시오.
5 이벤트 모니터 이벤트 모니터 기능은 Dell EMC PowerVault Modular Disk Storage Manager에 제공됩니다. 이벤트 모니터는 백그라운드에서 지속적으 로 실행되어 관리형 스토리지 어레이에서 작동을 모니터링합니다. 이벤트 모니터가 위험 수준의 문제점을 감지하면 이메일, SNMP(Simple Network Management Protocol) 트랩 메시지 또는 둘 다 사용하여 호스트나 원격 시스템에 알릴 수 있습니다. 이벤트 알림을 시기 적절하고 지속적으로 수신하려면 24시간 가동되는 관리 스테이션에 이벤트 모니터를 활성화합니다. 여러 시스템 에 이벤트 모니터를 활성화하거나 이벤트 모니터와 MD 스토리지 관리자를 조합하여 활성 상태로 유지하면 중복 이벤트가 발생할 수 있지만, 어레이에 다중 장애가 발생한 것은 아닙니다. 이벤트 모니터는 EMW(Enterprise Management Window)와 독립적으로 실행되는 배경 작업입니다.
6 호스트 정보 주제: • • • • • • • 호스트 액세스 구성 호스트 매핑 탭 사용 호스트 액세스 제거 호스트 그룹 관리 호스트 그룹 생성 I/O 데이터 경로 보호 호스트 포트 식별자 관리 호스트 액세스 구성 Dell EMC PowerVault Modular Disk Storage Manager(MD Storage Manager)는 여러 개의 모듈로 구성되어 있습니다. 이러한 모듈 중 하 나는 호스트 컨텍스트 에이전트로, MD 스토리지 관리자 설치 중에 설치되며 백그라운드에서 계속 실행됩니다. 호스트 컨텍스트 에이전트가 호스트에서 실행 중이면 해당 호스트와 이 호스트에서 스토리지 어레이로 연결된 호스트 포트는 MD 스 토리지 관리자에서 자동으로 검색됩니다. 호스트 포트는 어레이 관리 창(AMW)의 Host Mappings(호스트 매핑) 탭에 표시됩니다. 호 스트는 Host Mappings(호스트 매핑) 탭의 Default Host Group(기본 호스트 그룹)에서 수동으로 추가해야 합니다.
• 선택된 호스트 그룹에 매핑을 추가합니다. 호스트 정의 AMW에서 Define Host Wizard(호스트 정의 마법사)를 사용하여 스토리지 배열의 호스트를 정의할 수 있습니다. 알려진 관련이 없는 호스트 포트 식별자 또는 새 호스트 포트 식별자를 추가할 수 있습니다. 사용자 레이블은 호스트 포트 식별자를 추가하기 전에 지정해야 합니다. Add(추가) 단추는 입력이 발생될 때까지 비활성 상태입니 다. 호스트를 정의하려면 다음을 수행합니다. 1. AMW에서, Host Mappings(호스트 매핑) 탭을 선택합니다. 2. 다음 중 하나를 수행합니다. • • • 메뉴 표시줄에서 Host Mappings(호스트 매핑) > Define(정의) > Host(호스트)를 선택합니다. Setup(설정) 탭을 선택하고 Manually Define Hosts(수동으로 호스트 정의)를 클릭합니다. Host Mappings(호스트 매핑) 탭을 선택합니다.
• 호스트 노드를 마우스 오른쪽 단추로 클릭하고 팝업 메뉴에서 Remove(제거)를 선택합니다. Remove confirmation(제거 확인) 대화상자가 표시됩니다. 4. yes를 입력합니다. 5. 확인을 클릭합니다. 호스트 그룹 관리 호스트 그룹은 스토리지 배열의 특정 가상 디스크에 대한 액세스를 공유하는 둘 이상의 호스트로 구성된 논리 엔터티입니다. MD 스 토리지 관리자를 사용하여 호스트 그룹을 생성할 수 있습니다. 단일 호스트 그룹에 있는 모든 호스트의 유형(운영 체제)은 동일해야 합니다. 또한 호스트 그룹에 있는 모든 호스트에 클러스터링 소 프트웨어 등과 같은 특수 소프트웨어가 있어야 가상 디스크 공유 및 접근성을 관리할 수 있습니다. 호스트가 클러스터에 속해 있으면, 클러스터의 모든 호스트가 스토리지 배열에 연결되어야 하며 클러스터의 모든 호스트를 호스트 그룹에 추가해야 합니다. 호스트 그룹 생성 호스트 그룹을 생성하려면 다음 단계를 따르십시오. 1.
호스트 그룹에서 호스트를 이동하여 기본 그룹 아래에 추가할 수도 있습니다. Move Host Confirmation(호스트 이동 확인) 대화상자가 표시됩니다. 4. Yes(예)를 클릭합니다. 호스트가 다음과 같은 매핑과 함께 선택된 호스트 그룹으로 이동됩니다. • • • 호스트는 할당된 특정 가상 디스크 매핑을 보유합니다. 호스트는 이동되는 호스트 그룹에 할당된 가상 디스크 매핑을 상속합니다. 호스트가 이동되기 전에 속한 원래 호스트 그룹에 할당된 가상 디스크 매핑이 유실됩니다. 호스트 그룹 제거 호스트 그룹을 제거하려면 다음을 수행합니다. 1. AMW에서, Host Mappings(호스트 매핑) 탭을 선택하고 개체 트리에서 호스트 그룹을 선택합니다. 2. 다음 작업 중 하나를 수행합니다. • • 메뉴 표시줄에서 Host Mappings(호스트 매핑) > Host Group(호스트 그룹) > Remove(제거)를 선택합니다.
• Start(시작) > Administrative Tools(관리 도구) > Services(서비스)를 클릭합니다. 2. 서비스 목록에서 Modular Disk Storage Manager Agent(모듈러 디스크 스토리지 관리자 에이전트)를 선택합니다. 3. 호스트 컨텍스트 에이전트가 실행 중인 경우 Action(작업) > Stop(중지)을 클릭하고 약 5초 정도 기다립니다. 4. Action(작업) > Start(시작)를 클릭합니다. I/O 데이터 경로 보호 호스트에 여러 개의 호스트-배열 연결을 사용할 수 있습니다. 스토리지 배열의 호스트 액세스를 구성할 때는 배열에 대한 모든 연결 을 선택해야 합니다. 노트: 케이블 연결 구성에 대한 자세한 내용은 배포 안내서를 참조하십시오. 노트: 호스트 구성에 대한 자세한 내용은 호스트 정보를 참조하십시오.
9. Associated with host(호스트와 연관됨)에서, 적절한 호스트를 선택합니다. 새로 추가된 호스트 포트 식별자가 Host port identifier information(호스트 포트 식별자 정보) 영역에 추가됩니다. 10. Host port identifier information(호스트 포트 식별자 정보) 영역에 있는 호스트 포트 식별자 목록에서 관리할 호스트 포트 식별 자를 선택합니다. 11. 선택된 호스트 포트 식별자에 대해 다음 작업 중 하나를 수행합니다. • • • 56 호스트 포트 식별자 편집 - 적절한 호스트 포트 식별자를 선택하고 편집을 클릭하면 호스트 포트 식별자 편집 대화상자가 표 시됩니다. 사용자 레이블 및 호스트와 연관됨을 업데이트하고 저장을 클릭합니다. 호스트 포트 식별자 교체 - 적절한 호스트 포트 식별자를 선택하고 교체를 클릭하면 호스트 포트 식별자 교체 대화상자가 표 시됩니다.
7 디스크 그룹, 표준 가상 디스크 및 씬 가상 디스크 주제: • • • • • • • • • • • • • • 디스크 그룹 및 가상 디스크 생성 씬 가상 디스크 적절한 물리적 디스크 유형 선택 자체 암호화 디스크 기능을 이용한 물리적 디스크 보안 핫 스페어 물리적 디스크 구성 물리적 디스크 보안 인클로저 손실 방지 드로어 손실 보호 호스트-가상 디스크 매핑 제한된 매핑 스토리지 파티셔닝 디스크 그룹 및 가상 디스크 확장 디스크 그룹 마이그레이션 스토리지 어레이 미디어 검색 디스크 그룹 및 가상 디스크 생성 디스크 그룹은 스토리지 어레이의 구성되지 않은 용량에 생성되며, 가상 디스크는 디스크 그룹의 사용 가능한 용량에 생성됩니다. 하 나의 디스크 그룹에서 지원되는 최대 물리 디스크 수는 120개(프리미엄 기능이 활성화된 경우에는 180개), 입니다. 스토리지 어레이 에 연결된 호스트는 가상 디스크에 데이터를 쓰고 읽습니다.
디스크 그룹 생성 노트: 스토리지 어레이에 대한 디스크 그룹을 생성하지 않은 경우, AMW 실행 시, Disk Pool Automatic Configuration(디스크 풀 자동 구성) 마법사가 표시됩니다. 디스크 풀에서 스토리지 공간을 생성하는 방법에 대한 자세한 내용은 디스크 풀을 참조하십 시오. 노트: 씬 프로비저닝된 가상 디스크는 디스크 풀에서 생성할 수 있습니다. 디스크 풀을 사용하지 않을 경우 표준 가상 디스크만 생성할 수 있습니다. 자세한 내용은 씬 가상 디스크를 참조하십시오. Automatic(자동) 구성 또는 Manual(수동) 구성을 사용하여 디스크 그룹을 생성할 수 있습니다. 디스크 그룹을 생성하려면 다음을 수행합니다. 1. Create Disk Group Wizard(디스크 그룹 생성 마법사)를 시작하려면 다음 작업 중 하나를 수행합니다.
2. 디스크 그룹을 마우스 오른쪽 단추로 클릭하고 팝업 메뉴에서 Blink(깜박임)를 선택합니다. 선택한 디스크 그룹의 LED가 깜박거립니다. 3. 디스크 그룹을 찾은 다음 OK(확인)를 클릭합니다. LED 깜박임이 중지됩니다. 4. 디스크 그룹의 LED 깜박임이 중지되지 않으면 AMW의 도구 모음에서 Hardware(하드웨어) > Blink(깜박임) > Stop All Indications(모든 표시등 중지)를 선택합니다. LED가 더 이상 깜박거리지 않으면 확인 메시지가 표시됩니다. 5. 확인을 클릭합니다. 표준 가상 디스크 생성 표준 가상 디스크를 생성할 때 다음 주요 지침을 숙지하십시오. • • • • 대부분의 호스트가 스토리지 파티션당 매핑된 256개의 LUN(논리 단위 번호)을 보유할 수 있지만 이 번호는 운영 체제에 따라 다 릅니다. 하나 이상의 가상 디스크를 생성하고 매핑을 할당한 후에는 가상 디스크를 운영 체제에 등록해야 합니다.
10. Finish(마침)를 클릭합니다. 가상 디스크가 생성됩니다. 노트: 다른 가상 디스크를 생성할지 묻는 메시지가 표시됩니다. Yes(예)를 클릭하여 계속 진행하거나 No(아니요)를 클릭합 니다. 노트: 씬 가상 디스크는 디스크 풀에서 지원됩니다. 자세한 내용은 씬 가상 디스크를 참조하십시오. 가상 디스크의 수정 우선 순위 변경 스토리지 배열의 단일 가상 디스크 또는 다중 가상 디스크에 대한 수정 우선순위 설정을 지정할 수 있습니다. 가상 디스크의 수정 우선순위의 변경에 대한 지침: • • 둘 이상의 가상 디스크를 선택하는 경우, 수정 우선순위는 가장 낮음으로 기본 설정됩니다. 현재 우선순위는 단일 가상 디스크를 선택하는 경우에만 표시됩니다. 이 옵션을 사용하여 수정 우선순위를 변경하면 선택된 가상 디스크에 대한 우선순위가 수정됩니다. 가상 디스크의 수정 우선순위를 변경하려면 다음을 수행합니다. 1.
• ○ Enable write caching with replication(복제로 쓰기 캐싱 활성화) — 캐시 크기가 동일한 2개의 중복 RAID 컨트롤러 모듈 에서 캐시된 데이터를 복제합니다. Enable dynamic cache read prefetch(동적 캐시 읽기 프리패치 활성화) 주의: 데이터 손실 가능성 - Enable write caching without batteries(배터리 없이 쓰기 캐싱 활성화) 옵션을 선택하면 배터 리가 완전히 방전된 경우 또는 완전히 충전되지 않은 경우에도 계속해서 쓰기 캐싱을 수행할 수 있습니다. 일반적으로, 쓰기 캐싱은 배터리가 충전될 때까지 RAID 컨트롤러 모듈에서 일시적으로 꺼집니다. 이 옵션을 선택하고 보호를 위한 범용 전원 공급 장치를 사용하지 않는 경우 데이터가 유실될 수 있습니다.
I/O 유형 변경 스토리지 배열 구성의 일부로 정의하는 가상 디스크에 대해 가상 디스크 I/O 특징을 지정할 수 있습니다. 시스템에서 가상 디스크의 예상 I/O 특징은 적용 가능한 기본 가상 디스크 세그먼트 및 동적 캐시 읽기 프리패치 설정을 나타내는 데 사용됩니다. 노트: 동적 캐시 읽기 프리페치 설정은 메뉴 표시줄에서 Storage(스토리지) > Virtual Disk(가상 디스크) > Change(변경) > Cache Settings(캐시 설정)를 선택하여 나중에 변경할 수 있습니다. 메뉴 표시줄에서 Storage(스토리지) > Virtual Disk(가상 디스크) > Change(변경) > Segment Size(세그먼트 크기)를 선택하여 변경할 수 있습니다. 아래의 I/O 특징 유형은 가상 디스크 생성 과정 중에만 제시됩니다.
씬 프로비저닝을 사용하면 가상 용량은 크지만 실제 용량은 상대적으로 작은 가상 디스크를 생성할 수 있습니다. 이렇게 하면 응용 프 로그램 요구 사항이 달라짐에 따라 용량을 늘릴 수 있기 때문에 데이터 처리량에 영향을 주지 않고 스토리지 활용도와 효율이 향상된 다는 이점이 있습니다. 실제 용량의 지정된 비율에 도달했을 때 MD 스토리지 관리자가 경고를 생성하도록 활용도 경고 임계값을 설 정할 수도 있습니다. 기존 씬 가상 디스크에서 용량 변경 읽기/쓰기 작업을 위해 호스트가 사용한 공간(경우에 따라 소비된 용량이라고 함)이 표준 가상 디스크에 할당된 실제 공간을 초과할 경우 실제 용량이 늘어날 때까지 스토리지 어레이가 추가적인 쓰기 요청을 수용할 수 없습니다. 그러나 씬 가상 디스크에서 MD 스토 리지 관리자는 씬 가상 디스크의 실제 용량을 자동으로 확장할 수 있습니다.
씬 가상 디스크 상태 다음은 MD 스토리지 관리자에 표시되는 가상 디스크 상태입니다. Optimal(최적) — 가상 디스크가 정상적으로 작동합니다. Full(전체) — 씬 가상 디스크의 실제 용량이 꽉 찼거나 더 이상 호스트 쓰기 요청을 처리할 수 없습니다. Over Threshold(임계값 초과) — 씬 가상 디스크의 실제 용량이 지정된 Warning Threshold(경고 임계값) 비율에 도달했거나 이 를 초과합니다. 스토리지 어레이 상태가 Needs Attention(주의 요구)으로 표시됩니다. Failed(실패) — 가상 디스크가 실패했으며 읽기 또는 쓰기 작업에 더 이상 사용할 수 없습니다. 스토리지 어레이 상태가 Needs Attention(주의 요구)으로 표시됩니다. • • • • 비교 - 가상 디스크 및 복사 서비스 유형 복사 서비스의 가용성은 작업 중인 가상 디스크의 유형에 따라 다릅니다. 표 9.
• • • 동일한 실제 용량 유지 — 동일한 실제 용량을 유지하면 가상 디스크가 현재 저장소 가상 디스크를 유지할 수 있으므로 초기화 시 간이 절약됩니다. 실제 용량 변경 — 실제 용량을 변경하면 새 저장소 가상 디스크가 생성되고 선택적으로 저장소 확장 정책 및 경고 임계값을 변경 할 수 있습니다. 저장소를 다른 디스크 풀로 이동합니다. 씬 가상 디스크를 초기화하면 가상 디스크에서 모든 데이터가 지워집니다. 그러나 호스트 매핑, 가상 용량. 저장소 확장 정책 및 보안 설정은 보존됩니다. 초기화는 또한 블록 색인을 지우기 때문에 쓰지 않은 블록이 0으로 채워진 것처럼 인식됩니다. 초기화 후에는 씬 가상 디스크가 완전히 빈 것으로 나타납니다. 다음 유형의 가상 디스크는 초기화할 수 없습니다.
노트: 모든 용량을 표준 가상 디스크로 할당하지 마십시오. 스토리지 용량을 복사 서비스(스냅샷 이미지, 스냅샷 가상 디스 크, 가상 디스크 복사 및 원격 복제)를 위해 유지해야 합니다. 노트: 지정한 용량에 상관없이 디스크 풀의 용량은 4GB 증분으로 할당됩니다. 4GB의 배수가 아닌 용량은 할당은 되지만 사 용할 수 없습니다. 전체 용량을 사용할 수 있도록 하려면 용량을 4GB 증분으로 지정하십시오. 사용할 수 없는 용량이 존재할 경우 다시 용량을 확보하는 유일한 방법은 가상 디스크의 용량을 늘리는 것입니다. 이전 단계에서 입력한 값을 기준으로 Disk pool physical capacity candidates(디스크 풀 실제 용량 후보) 표가 일치하는 저장소 로 채워집니다. 9. 표에서 저장소를 선택합니다. 기존 저장소는 목록 맨 위에 있습니다. 노트: 기존 저장소를 다시 사용하면 새로 생성할 때 발생하는 초기화 프로세스를 피할 수 있다는 이점이 있습니다. 10.
노트: 기존 저장소를 다시 사용하면 새로 생성할 때 발생하는 초기화 프로세스를 피할 수 있다는 이점이 있습니다. 10. 저장소 확장 정책이나 경고 임계값을 변경하려면 View advanced repository settings(고급 저장소 설정 보기)를 클릭합니다. • • Repository expansion policy(저장소 확장 정책) - Automatic(자동) 또는 Manual(수동)을 선택합니다. 소비한 용량이 실제 용량에 근접하면 실제 용량을 확장할 수 있습니다. MD Storage Manager는 실제 용량을 자동으로 확장하거나 사용자가 수동으 로 확장할 수 있습니다. Automatic(자동)을 선택할 경우 최대 확장 용량을 설정할 수도 있습니다. 최대 확장 용량을 사용하면 가상 디스크의 자동 늘리기를 가상 용량 미만으로 제한할 수 있습니다. 최대 확장 용량의 값은 4GB의 배수여야 합니다.
자체 암호화 디스크 또는 보안 가능 물리 디스크는 쓰기 작업 중 데이터를 암호화하고 읽기 작업 중 데이터를 복호화합니다. 보안 가능 물리적 디스크에서 보안 디스크 그룹을 생성할 수 있습니다. 보안 가능 물리적 디스크에서 보안 디스크 그룹을 생성하면, 해당 디스크 그룹에 있는 물리적 디스크에 보안이 활성화됩니다. 보안 가능 물리적 디스크의 보안이 활성화되면 물리적 디스크에는 RAID 컨트롤러 모듈에서 제공하는 올바른 보안 키가 있어야 데이터를 읽거나 쓸 수 있습니다. 스토리지 어레이의 모든 물리적 디스크 와 RAID 컨트롤러 모듈은 보안 키를 공유합니다. 보안 키를 공유하면 물리적 디스크에 읽기 및 쓰기 액세스 권한이 부여되며, 각 물리 적 디스크의 물리적 디스크 암호화 키는 데이터를 암호화하는 데 사용됩니다. 보안 가능 물리적 디스크는 보안이 활성화되기 전까지 다른 물리적 디스크와 마찬가지로 작동됩니다. 전원이 꺼졌다가 다시 켜질 때마다, 보안이 활성화된 모든 물리적 디스크는 보안 잠금 상태가 됩니다.
다른 디스크 그룹 또는 다른 스토리지 어레이에서 물리적 디스크를 재사용할 수 있도록 보안이 활성화된 물리적 디스크를 지울 수 있 습니다. 보안이 활성화된 물리적 디스크를 지우면 데이터를 읽을 수 없습니다. Physical Disk type(물리적 디스크 유형) 창에서 선택한 모든 물리적 디스크가 보안이 활성화된 상태이고, 선택된 물리적 디스크가 디스크 그룹에 속하지 않을 경우 Secure Erase(보안 지우 기) 옵션이 Hardware(하드웨어) 메뉴에 표시됩니다. 스토리지 배열 암호는 인증되지 않은 사용자가 잠재적으로 파괴적인 작업을 수행하지 못하도록 방지합니다. 스토리지 배열 암호는 자체 암호화 디스크와 관계가 없으며 보안 키 복사본을 보호하는 데 사용되는 패스프레이즈(pass phrase)와 혼동하지 않아야 합니다. 하지만 스토리지 배열 암호를 설정하는 것이 바람직합니다. 보안 키 생성 사용자가 보안 키를 만들면 배열이 보안 키를 생성하여 안전하게 저장합니다.
9. Confirm pass phrase(패스프레이즈 확인) 대화상자에서, Pass phrase(패스프레이즈) 대화상자에 입력한 정확한 문자열을 다시 입력합니다. 입력한 패스프레이즈 및 연관된 보안 키 식별자를 기록해 두십시오. 나중에 보안 작업을 수행할 때 이 정보가 필요합니다. 10. Create Key(키 생성)를 클릭합니다. 11. Invalid Text Entry(무효한 텍스트 입력) 대화상자가 표시되면 다음을 선택합니다. • • Yes(예) — 입력한 문자열에 오류가 있습니다. Invalid Text Entry(무효한 텍스트 입력) 대화상자가 표시됩니다. 대화상자의 오류 메시지를 읽고 OK(확인)를 클릭합니다. 6단계로 이동합니다. No(아니오) — 입력한 문자열에 오류가 없습니다. 12단계로 이동합니다. 12. Create Security Key Complete(보안 키 생성 완료) 대화상자에서 보안 키 식별자 및 파일 이름을 기록해두고 OK(확인)를 클릭 합니다.
보안 키 저장 보안 키가 처음 생성되고 보안 키가 변경될 때마다 외부에 저장 가능한 보안 키 복사본을 저장할 수 있습니다. 저장 가능한 복사본은 언제든지 추가적으로 생성할 수 있습니다. 보안 키의 새 복사본을 저장하려면 패스프레이즈(pass phrase)를 제공해야 합니다. 사용자 가 선택하는 패스프레이즈는 보안 키가 생성되거나 마지막으로 변경될 때 사용된 패스프레이즈와 동일하지 않아도 됩니다. 패스프레 이즈는 저장하려고 하는 보안 키의 특정 복사본에 적용됩니다. 스토리지 배열의 보안 키를 저장하려면 다음을 수행합니다. 1. AMW 도구 모음에서 Storage Array(스토리지 배열) > Security(보안) > Physical Disk Security(물리 디스크 보안) > Save Key(키 저장)를 선택합니다. Save Security Key File - Enter Pass Phrase(보안 키 파일 저장 - 패스프레이즈 입력) 창이 표시됩니다. 2.
보안 지우기 절차를 완료한 후에는 다른 디스크 그룹 또는 다른 스토리지 배열에서 해당 물리 디스크를 사용할 수 있습니다. 보안 지 우기 절차에 대한 자세한 내용은 도움말 항목을 참조하십시오. 핫 스페어 물리적 디스크 구성 핫스페어 물리 디스크 구성에 대한 지침: 주의: 핫 스페어 물리적 디스크의 상태가 Optimal(최적)이 아닐 경우, Recovery Guru(복구 안내) 절차에 따라 문제를 수정한 후 에 물리적 디스크를 할당 해제하십시오. 사용 중인 핫 스페어 물리적 디스크는 할당할 수 없습니다(장애가 발생한 물리적 디스크 를 대신함) • • • • • • Optimal(최적) 상태의 할당 해제된 물리 디스크만 핫스페어 물리 디스크로 사용할 수 있습니다. Optimal(최적) 또는 Standby(대기) 상태의 핫스페어 물리 디스크만 할당 해제할 수 있습니다. In Use(사용 중) 상태의 핫스페어 물리 디스크는 할당 해제할 수 없습니다.
핫 스페어 및 재구축 데이터를 보호하는 중요한 방법 중 하나는 스토리지 배열의 사용 가능한 물리 디스크를 핫스페어로 할당하는 것입니다. 핫스페어는 또 다른 수준의 내결함성을 스토리지 배열에 추가합니다. 핫스페어는 디스크에 장애가 발생할 경우 즉시 사용할 수 있는 유휴, 전원 켜짐, 대기 상태의 물리 디스크입니다. 중복 가상 디스크에 물리 디스크 장애가 있는 인클로저에 핫스페어가 정의되어 있으면, RAID 컨트롤러 모듈은 저하된 가상 디스크의 재구축을 자동으로 시작합니다. 핫스페어가 정의되어 있지 않으면 교체 물리 디스크가 스토리지 배열에 삽입될 때 RAID 컨트롤러 모듈이 재구축 프로세 스를 시작합니다. 전역 핫 스페어 MD Series 스토리지 어레이는 전역 핫스페어를 지원합니다. 전역 핫스페어는 핫스페어의 용량이 메타데이터를 포함하여 대체하는 실 제 디스크에 구성된 용량의 크기와 동일하거나 큰 경우에 중복 RAID 레벨의 가상 디스크에서 장애가 발생한 실제 디스크를 대체할 수 있습니다.
노트: 디스크 풀 또는 디스크 그룹에 보안이 활성화되어 있는 경우, 보안을 제거하는 유일한 방법은 디스크 풀 또는 디스크 그룹 을 삭제하는 것입니다. 디스크 풀 또는 디스크 그룹을 삭제하면 가상 디스크에 포함된 모든 데이터가 삭제됩니다. 스토리지 배열의 컨트롤러에는 보안 키가 있습니다. 보안 물리 디스크는 올바른 보안 키가 있는 컨트롤러를 통해서만 데이터에 대한 액세스를 제공합니다. 보안 가능 물리 디스크에서 보안 디스크 풀 또는 디스크 그룹을 생성하면, 해당 디스크 풀 또는 디스크 그룹에 있는 물리 디스크에 보안이 활성화됩니다. 보안 가능 물리적 디스크의 보안이 활성화되면 물리적 디스크에는 컨트롤러에서 제공하는 올바른 보안 키가 있어야 데이터를 읽거나 쓸 수 있습니다. 스토리지 어레이의 모든 물리적 디스크와 컨트롤러는 보안 키를 공유합니다. 또한 SED 물리적 디스크와 FIPS 물리적 디스크가 모두 있으면, 이 디스크도 보안 키를 공유합니다.
드로어 손실 보호 서랍 기반 물리 디스크가 포함된 확장 인클로저에서, 서랍 장애로 인해 디스크 그룹에 있는 가상 디스크의 데이터에 액세스하지 못할 수 있습니다. 디스크 그룹의 드로어 손실 보호는 디스크 그룹을 구성하는 물리적 디스크의 위치를 기준으로 합니다. 단일 드로어에 장애가 발생하 는 경우, 드로어 손실 보호 구성에 따라 디스크 그룹에 있는 가상 디스크의 데이터는 액세스 가능한 상태로 유지됩니다. 드로어에 장 애가 발생하고 디스크 그룹이 보호되는 경우에는 디스크 그룹이 Degraded(성능 저하) 상태로 변경되고 데이터는 액세스 가능한 상태 로 유지됩니다. 표 12. 각 RAID 레벨에 대한 드로어 손실 보호 요구 사항 RAID 레벨 서랍 손실 보호 요구사항 RAID 레벨 6 RAID 레벨 6의 경우 최소 5개의 물리적 디스크가 필요합니다.
호스트-가상 디스크 매핑 생성 매핑 정의에 대한 지침: • • • 대역외 스토리지 배열에는 액세스 가상 디스크 매핑이 필요하지 않습니다. 대역외 연결을 사용하여 스토리지 배열을 관리하고 액 세스 가상 디스크 매핑이 기본 그룹에 할당되어 있는 경우, 액세스 가상 디스크 매핑은 기본 그룹에서 생성된 모든 호스트에 할당 됩니다. 대부분의 호스트는 스토리지 파티션 당 매핑된 256개의 LUN을 보유합니다. 이 LUN은 0 - 255로 번호가 지정됩니다. 사용 중인 운 영 체제에서 LUN의 개수가 127개로 제한되고 사용자가 127개 이상의 LUN에 가상 디스크를 매핑하려고 시도하면 호스트가 액세 스하지 못합니다. 호스트 그룹 또는 호스트의 초기 매핑은 추가 매핑을 정의하기 전에 Storage Partitioning Wizard(스토리지 파티셔닝 마법사)를 사 용하여 생성해야 합니다. 스토리지 파티셔닝을 참조하십시오. 호스트-가상 디스크 매핑을 생성하려면 다음을 수행합니다. 1.
드롭다운 목록에 선택한 가상 디스크와 연관된 현재 사용 가능한 LUN만 표시됩니다. 5. 확인을 클릭합니다. 노트: 이 가상 디스크와 연관된 호스트 응용프로그램을 중지하고, 해당되는 경우 운영 체제에서 가상 디스크를 제거합니다. 6. Change Mapping(매핑 변경) 대화상자에서, Yes(예)를 클릭하여 변경사항을 확인합니다. 매핑의 유효성이 검사된 후 저장됩니다. Defined Mappings(정의된 매핑) 창이 업데이트되어 새 매핑을 반영합니다. 개체 트리도 업데이트되어 호스트 그룹 또는 호스트의 모든 이동을 반영합니다. 7. 스토리지 배열에 암호가 설정되어 있으면 Enter Password(암호 입력) 대화상자가 표시됩니다. 스토리지 배열의 현재 암호를 입 력하고 OK(확인)를 클릭합니다. 8. Linux 호스트를 구성하는 경우, 호스트에 있는 rescan_dm_devs 유틸리티를 실행하고 필요한 경우 가상 디스크를 제거합니다.
2. 메뉴 표시줄에서 Storage(스토리지) > Disk Group(디스크 그룹) > Change(변경) > Ownership/Preferred Path(소유권/기본 경로)를 선택합니다. 3. 적절한 RAID 컨트롤러 모듈 슬롯을 선택하고 Yes(예)를 클릭하여 선택을 확인합니다. 주의: 데이터 액세스 손실 가능성 - 디스크 그룹 레벨에서 소유권을 변경하면 해당 디스크 그룹에 있는 모든 가상 디스크가 다 른 RAID 컨트롤러 모듈로 전송되고 새 I/O 경로를 사용하게 됩니다. 모든 가상 디스크를 새 경로를 설정하지 않으려면 가상 디스크 레벨에서 소유권을 변경하십시오. 디스크 그룹의 소유권이 변경됩니다. 디스크 그룹의 I/O가 이 I/O 경로를 통해 이동됩니다. 노트: 다중경로 드라이브가 새 경로를 재구성하여 인식해야 디스크 그룹이 새 I/O 경로를 사용합니다. 이 작업은 일반적으로 5분 미만이 소요됩니다.
노트: 매핑에서 삭제할 가상 디스크가 표시됩니다. 예를 들어, 다음과 같은 정보가 표시됩니다. mpath6 (3600a0b80000fb6e50000000e487b02f5) dm-10 DELL, MD32xx [size=1.6T][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac] \_ round-robin 0 [prio=6][active] \_ 1:0:0:2 sdf 8:80 [active][ready] \_ round-robin 0 [prio=1][enabled] \_ 0:0:0:2 sde 8:64 [active][ghost] 이 예에서 mpath6 장치에는 다음 두 경로가 포함되어 있습니다. -- /dev/sdf at Host 1, Channel 0, Target 0, LUN 2 --/dev/sde at Host 0, Channel 0, Target 0, LUN 2 3. 다음 명령을 사용하여 다중 경로 디바이스 매핑을 플러시합니다.
표 13. 운영 체제의 LUN 최대값 운영체제 LUN 최대값 Windows Server 2003 및 Windows Server 2008 255 Linux 255 LUN 매핑 제한사항이 있는 호스트 유형 작업에 대한 지침: • • • • • • 제한된 호스트 유형에 의해 발생된 한도를 초과하는 매핑이 스토리지 파티션에 이미 존재하는 경우, 호스트 어댑터 포트를 제한 된 호스트 유형으로 변경할 수 없습니다 최대 256개(0 - 255개)의 LUN에 액세스할 수 있는 기본 그룹이 있고 제한된 호스트 유형이 기본 그룹에 추가된다고 가정해 보겠 습니다. 이 경우, 제한된 호스트 유형과 연관된 호스트는 기본 그룹에서 해당 한도 범위 내의 LUN이 있는 가상 디스크에 액세스할 수 있습니다. 예를 들어 기본 그룹에 있는 2개의 가상 디스크가 각각 254개의 LUN과 255개의 LUN에 매핑되어 있을 경우, 제한된 호스트 유형과 연관된 호스트는 이러한 2개의 가상 디스크에 액세스할 수 없습니다.
스토리지 파티셔닝 토폴로지는 AMW에서 Host Mappings(호스트 매핑) 탭의 개체 트리에 노드로 표시되는 기본 그룹, 호스트 그룹, 호스트 및 호스트 포트와 같은 요소 모음입니다. 자세한 내용은 호스트 매핑 탭 사용을 참조하십시오. 스토리지 파티셔닝 토폴로지가 정의되지 있지 않은 경우, Host Mappings(호스트 매핑) 탭을 선택할 때마다 정보 대화상자가 표시됩 니다. 실제 스토리지 파티션을 정의하기 전에 스토리지 파티셔닝 토폴로지를 정의해야 합니다. 디스크 그룹 및 가상 디스크 확장 배열의 구성되지 않은 용량을 디스크 그룹에 추가하여 디스크 그룹에 사용 가능한 용량을 추가할 수 있습니다. 전체 수정 과정 중에 디스크 그룹, 가상 디스크, 물리 디스크에서 데이터에 액세스할 수 있습니다. 추가적인 사용 가능한 공간을 사용하여 표준 또는 스냅 샷 저장소 가상 디스크에서 가상 디스크 확장을 수행할 수 있습니다. 디스크 그룹 확장 디스크 그룹에 사용 가능한 용량을 추가하려면 다음을 수행합니다.
5. Increase Virtual Disk Capacity(가상 디스크 용량 증가) 창에서 필요한 메모리 볼륨을 입력하여 가상 디스크의 용량을 증가시킵 니다. 디스크를 더 추가해야 하는 경우 Add Physical Disks(물리적 디스크 추가)를 선택합니다. 디스크 그룹 확장 지침에 대한 자세한 내용은 디스크 그룹 확장 페이지 81을 참조하십시오. 6. 확인을 클릭합니다. 이 작업을 시작한 후에는 취소할 수 없으며 완료하는 데 다소 시간이 소요될 수 있습니다. 그러나 가상 디스크는 액세스 가능한 상 태로 유지됩니다. 노트: Windows 및 Linux 호스트에서 CLI(Command Line Interface)를 사용하여 가상 디스크의 용량을 증가시킬 수도 있습니 다. 자세한 정보는 Dell EMC PowerVault MD 34XX/38XX 시리즈 스토리지 어레이 CLI 안내서를 참조하십시오.
2. 3. 4. 5. 6. 모든 I/O를 중지하고 디스크 그룹의 가상 디스크에 있는 파일 시스템을 분리합니다. 디스크 그룹의 가상 디스크에 있는 데이터를 백업합니다. 디스크 그룹의 위치를 찾아 물리 디스크를 분류합니다. 디스크 그룹을 오프라인으로 전환합니다. 비어 있는 물리 디스크 모듈이나 새 물리 디스크를 확보합니다. 대상 스토리지 배열에서 다음과 같은 사항을 확인합니다. • • • • 대상 스토리지 배열에 사용 가능한 물리 디스크 슬롯이 있는지 확인합니다. 대상 스토리지 배열이 사용자가 가져올 물리 디스크를 지원하는지 여부를 확인합니다. 대상 스토리지 배열이 새 가상 디스크를 지원할 수 있는지 확인합니다. 최신 펌웨어 버전이 RAID 컨트롤러 모듈에 설치되어 있는지 확인합니다. 디스크 그룹 가져오기 디스크 그룹 가져오기 작업을 수행하면 가져온 디스크 그룹이 대상 스토리지 배열에 추가됩니다. 디스크 그룹 가져오기 작업을 완료 하면 모든 물리 디스크의 상태가 Optimal(최적)이 됩니다.
• • • • 복구되지 않은 매체 오류 - 이 오류는 첫 번째 시도 또는 이후의 시도에서 데이터를 읽을 수 없는 경우에 발생합니다. 일관성 보호 가 있는 가상 디스크의 경우 데이터가 재건되고 물리 디스크에 다시 작성된 후 확인되며, 이벤트 로그에 오류가 보고됩니다. 일관 성 보호가 없는 가상 디스크의 경우(RAID 1, RAID 5, RAID 6 가상 디스크) 오류가 정정되지 않지만 이벤트 로그에 보고됩니다. 복구된 매체 오류 - 이 오류는 첫 번째 시도에서는 물리 디스크가 데이터를 읽을 수 없었지만 이후의 시도에서는 읽을 수 있는 경 우에 발생합니다. 데이터가 물리 디스크에 다시 작성되어 확인되고 이벤트 로그에 오류가 보고됩니다. 일관성 불일치 오류 — 가상 디스크에서 발견된 처음 10개의 일관성 불일치가 이벤트 로그에 보고됩니다. 수정 불가능 오류 — 데이터를 읽을 수 없고 데이터 재생성에 일관성 또는 일관성 정보를 사용할 수 없는 경우에 발생하는 오류입 니다.
8 디스크 풀 및 디스크 풀 가상 디스크 디스크 풀링을 통해 물리 디스크 집합에서 임의로 각 가상 디스크의 데이터를 분산시킬 수 있습니다. 디스크 풀링 기능을 사용하면 스 토리지 어레이에서 논리적으로 그룹화된 물리 디스크 집합에서 RAID를 보호하고 일관적인 성능을 유지할 수 있습니다. 디스크 풀을 구성하는 최대 물리 디스크 수에는 제한이 없지만 각 디스크 풀에는 최소 11개의 물리 디스크가 있어야 합니다. 또한 디스크 풀에는 각 스토리지 어레이의 최대 한도를 초과하는 물리 디스크가 포함될 수 없습니다. 각 디스크 풀의 물리 디스크에 대한 필수 조건은 다음과 같습니다. • • SAS 또는 선형 SAS여야 합니다. 물리 디스크 속도(RPM)가 동일해야 합니다. 노트: 최대 물리 디스크 속도는 표준 SAS의 경우 15,000rpm이고 3.5" 선형 SAS의 경우 7,200rpm입니다. 노트: 디스크 풀에서 물리 디스크의 용량이 동일해야 합니다.
디스크 풀 제한 사항 주의: 디스크 풀로 구성된 스토리지 배열의 RAID 컨트롤러 모듈 펌웨어 버전을 디스크 풀이 지원되지 않는 펌웨어 버전으로 다 운그레이드하는 경우, 가상 디스크가 유실되고 물리 디스크는 디스크 풀과 연관되지 않은 것으로 처리됩니다. • • • • • • 디스크 풀의 모든 물리 디스크 매체 유형은 동일해야 합니다. 솔리드 스테이트 디스크(SSD)는 지원되지 않습니다. 디스크 풀에서 가상 디스크의 세그먼트 크기를 변경할 수 없습니다. 스토리지 배열에서 디스크 풀을 내보내거나 다른 스토리지 배열에 디스크 풀을 가져올 수 없습니다. 디스크 풀의 RAID 레벨을 변경할 수 없습니다. MD 스토리지 관리자가 자동으로 디스크 풀을 RAID 레벨 6로 구성합니다. 디스크 풀의 모든 물리 디스크 유형은 동일해야 합니다. 자체 암호화 디스크(SED)로 디스크 풀을 보호할 수 있지만, 물리 디스크 특성이 일치해야 합니다.
디스크 풀에서 구성되지 않은 용량 자동으로 관리 MD 스토리지 관리자는 스토리지 배열에서 구성되지 않은 용량을 감지할 수 있습니다. 구성되지 않은 용량이 감지되면, MD 스토리지 관리자는 하나 이상의 디스크 풀을 생성하거나 기존 디스크 풀에 구성되지 않은 용량을 추가하라는 메시지를 표시합니다. 기본적으 로, 다음과 같은 조건 중 하나가 충족되면 Automatic Configuration(자동 구성) 대화상자가 표시됩니다. • • AMW가 열려 있어 스토리지 어레이를 관리할 수 있고, 디스크 풀이 스토리지 어레이에 없으며, 디스크 풀을 생성할 유사한 물리적 디스크가 부족한 경우 하나 이상의 디스크 풀이 있는 스토리지 배열에 새 물리 디스크가 추가된 경우. 사용 가능하며 적합한 물리 디스크가 부족할 경우, 기존 디스크 풀과 다른 물리 디스크 유형의 디스크 풀을 생성할 수 있습니다.
• • • • • 디스크 풀 이름에 문자, 숫자, 특수 문자인 밑줄(_), 하이픈(-), 파운드 부호(#)를 사용할 수 있습니다. 다른 문자를 사용하면 오류 메시지와 함께 다른 이름을 선택하라는 메시지가 표시됩니다. 디스크 풀 이름은 최대 30자입니다. 쉽게 알아보고 기억할 수 있는 고유하고 의미 있는 이름을 사용합니다. 임의의 이름이나 나중에 의미가 쉽게 상실되는 이름은 사용하지 마십시오. 이미 사용 중인 디스크 풀 이름을 선택하면 오류 메시지와 함께 다른 이름을 선택하라는 메시지가 표시됩니다. 디스크 풀의 경고 알림을 구성하려면 다음을 수행합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 디스크 풀을 선택합니다. 3. 메뉴 표시줄에서 Storage(스토리지) > Disk Pool(디스크 풀) > Rename(이름 변경)을 선택합니다. 또는 디스크 풀을 마우스 오 른쪽 단추로 클릭하고 Rename(이름 변경)을 선택합니다.
노트: RAID 컨트롤러 모듈 펌웨어는 할당되지 않은 물리 디스크 옵션을 Select physical disks for addition(추가할 물리 디스크 선택) 영역 맨 위에 나열된 최상의 옵션과 함께 정렬합니다. 4. Select physical disks for addition(추가할 물리 디스크 선택) 영역에서 하나 이상의 물리 디스크를 선택합니다. 디스크 풀에 추가되는 총 사용 가능한 용량이 Total usable capacity selected(선택한 총 사용 가능한 용량) 필드에 표시됩니다. 5. 추가를 클릭합니다. 디스크 풀의 보존 용량 구성 디스크 풀의 보존 용량은 물리 디스크에 장애가 발생하는 경우 데이터 재건 작업에 사용됩니다. 디스크 풀의 보존 용량을 구성하려면 다음을 수행합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 디스크 풀을 선택합니다. 3.
디스크 풀의 RAID 컨트롤러 모듈 소유권 변경 디스크 풀의 RAID 컨트롤러 모듈 소유권을 변경하여 RAID 컨트롤러 모듈이 디스크 풀에 있는 모든 가상 디스크를 소유하도록 지정할 수 있습니다. 디스크 풀 레벨에서 RAID 컨트롤러 모듈 소유권을 변경하면 해당 디스크 풀에 있는 각 가상 디스크가 다른 RAID 컨트롤러 모듈로 이 전되고 새 I/O 경로를 사용합니다. 각 가상 디스크가 새 경로를 사용하지 않도록 하려면 RAID 컨트롤러 모듈 소유권을 디스크 풀 레벨 이 아닌 가상 디스크 레벨에서 변경하십시오. 주의: 데이터 액세스 유실 가능성 - 응용프로그램이 디스크 풀의 가상 디스크에 액세스하고 있는 동안 RAID 컨트롤러 모듈 소유 권을 변경하면 I/O 오류가 발생할 수 있습니다. 응용프로그램이 가상 디스크에 액세스하고 있지 않은지 확인하고 호스트에 다중 경로 드라이버가 설치되어 있는지 확인한 후 이 절차를 수행하십시오. 디스크 풀의 RAID 컨트롤러 모듈 소유권을 변경하려면 다음을 수행합니다. 1.
디스크 풀 삭제 Delete(삭제) 옵션을 사용하여 디스크 풀과 디스크 풀에 있는 모든 가상 디스크를 삭제합니다. 디스크 풀이 삭제되면 해당 디스크 풀 과 연관된 물리적 디스크가 Unassigned(할당 해제됨) 상태로 변경됩니다. 이 경우, 스토리지 어레이에 구성되지 않은 용량이 추가로 생성되며 이 용량을 스토리지에 맞게 재구성할 수 있습니다. 주의: 데이터 액세스 유실 가능성 - 디스크 풀을 삭제하면 디스크 풀에 있는 가상 디스크의 모든 데이터가 손실됩니다. 이 작업을 수행하기 전에 디스크 풀에 있는 모든 가상 디스크의 데이터를 백업하고, 모든 입력/출력(I/O)을 중지하고, 가상 디스크에서 모 든 파일 시스템을 마운트 해제하십시오. 디스크 풀을 삭제하기 전에 다음 지침을 숙지하십시오. • 스냅샷 저장소 가상 디스크가 포함된 디스크 풀을 삭제하는 경우, 연관된 스냅샷 가상 디스크를 삭제하기 전에 기본 가상 디스크 를 삭제해야 합니다.
주의: 데이터 액세스 유실 가능성 - 디스크 풀에 보안이 설정되면, 보안을 제거해야만 디스크 풀을 삭제할 수 있습니다. 디스크 풀을 삭제하면 디스크 풀을 구성하고 있는 가상 디스크의 모든 데이터가 삭제됩니다. 전원을 껐다가 다시 켤 때마다 보안 활성화된 모든 물리적 디스크가 Security Locked(보안 잠금) 상태로 변경됩니다. 이 경우, RAID 컨 트롤러 모듈이 올바른 보안 키를 제공해야 데이터에 액세스할 수 있습니다. Disk Pool Properties(디스크 풀 속성) 대화상자에서 스 토리지 어레이의 모든 디스크 풀의 Physical Disk Security(물리적 디스크 보안) 상태를 볼 수 있습니다. 다음과 같은 상태 정보가 보고 됩니다. 보안 가능 보안 • • 표 14. 디스크 풀의 보안 속성 상태 보안 가능 - 예 보안 가능 - 아니오 보안 - 예 디스크 풀이 모든 SED 물리 디스크로 구성되며 Secure(보안) 상태입니다. 적용되지 않음.
최소 가상 용량은 32MB입니다. 6. Virtual disk name(가상 디스크 이름) 상자에 가상 디스크의 이름을 입력합니다. 7. 가상 디스크에 호스트를 매핑하려면 Map later(나중에 매핑)를 선택합니다. 가상 디스크에는 LUN이 할당되지 않으며 사용자가 Host Mappings(호스트 매핑) 탭으로 이동하고 특정 호스트와 LUN을 이 가상 디스크에 할당할 때까지 호스트에서 액세스할 수 없습니다. 8. 플래시 SSD 캐시를 사용하려면 Use flash SSD cache(플래시 SSD 캐시 사용)를 선택합니다. 플래시 SSD 캐시는 가상 디스크의 읽기 성능을 일반적인 하드 드라이브보다 한층 더 높이기 위해 SSD(Solid State Drive)에서 사용 자 선택 가상 디스크의 읽기 전용 캐싱을 제공합니다. 하드 드라이브에서 고성능 SSD로 투명하게 이어지는 이 데이터 복사 프로 세스는 애플리케이션 I/O 성능과 응답 시간을 개선합니다.
9 SSD 캐시 사용 SSD 캐시 기능은 SSD(Solid State Disk) 물리적 디스크를 활용하여 스토리지 어레이의 읽기 전용 성능을 개선합니다. SSD 물리적 디 스크는 RAID 컨트롤러 모듈 메모리에서 기본 캐시와 함께 사용하기 위한 보조 캐시를 제공하도록 논리적으로 그룹화됩니다. SSD 캐시를 사용하면 애플리케이션 처리량이 늘어나고, 응답 시간이 개선되며 다양한 워크로드, 특히 높은 IOP 워크로드에서 지속적 으로 향상된 성능을 제공합니다.
다음 옵션도 선택할 수 있습니다. • • • 다양한 개수의 SSD 물리 디스크로 구성된 가능한 후보 목록에서 SSD 캐시의 용량 현재 호스트에 매핑된 자격 있는 모든 가상 디스크에서 SSD 캐시를 활성화할지 여부 기존 가상 디스크에서 SSD 캐시를 사용할지 여부 또는 새 가상 디스크를 생성할 시기 SSD 캐시 제한 사항 다음 제한 사항은 SSD 캐시 기능을 사용할 때 적용됩니다. • • • • • • • SSD 캐시는 스냅샷 가상 디스크에서 지원되지 않습니다. SSD 캐시가 활성화되거나 비활성화된 기본 가상 디스크를 가져오거나 내보낼 경우 캐시된 데이터는 가져오거나 내보내지 않습 니다. 스토리지 어레이에서 사용 가능한 최대 SSD 캐시 용량은 RAID 컨트롤러 모듈의 기본 캐시 용량에 따라 다릅니다. 먼저 SSD 캐시를 삭제하지 않고 SSD 캐시의 마지막 물리 디스크를 제거할 수 없습니다. 스토리지 어레이당 하나의 SSD 캐시만 지원됩니다.
SSD 캐시에서 물리적 디스크 찾기 Blink(깜박임) 옵션을 사용하여 SSD 캐시에서 물리 디스크를 찾을 수 있습니다. SSD 캐시에서 물리 디스크를 찾으려면 다음 단계를 따르십시오. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 트리 보기에서 SSD 캐시를 선택하고 다음 중 하나를 수행합니다. • • 메뉴 표시줄에서 Storage(스토리지) > SSD Cache(SSD 캐시) > Blink(깜박임)를 선택합니다. SSD 캐시를 마우스 오른쪽 단추로 클릭하고 Blink(깜박임)를 선택합니다. SSD 캐시를 구성하는 물리 디스크의 LED가 깜박입니다. 3. 물리 디스크를 찾은 후에 OK(확인)를 클릭합니다. LED 깜박임이 중지됩니다. 4. 디스크 그룹의 LED 깜박임이 중지되지 않으면 AMW의 도구 모음에서 Hardware(하드웨어) > Blink(깜박임) > Stop All Indications(모든 표시등 중지)를 선택합니다.
• • 메뉴 표시줄에서 Storage(스토리지) > SSD Cache(SSD 캐시) > Resume(재개)을 선택합니다. SSD 캐시를 마우스 오른쪽 단추로 클릭하고 Resume(재개)을 선택합니다. SSD 캐시의 표 보기에 Status(상태)가 Optimal(최적)로 표시됩니다. SSD 캐시에서 I/O 유형 변경 SSD 캐시에서 I/O 유형을 변경하려면 다음 단계를 따르십시오. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 다음 중 하나를 수행합니다. • • 메뉴 표시줄에서 Storage(스토리지) > SSD Cache(SSD 캐시) > Change I/O Type(I/O 유형 변경)을 선택하고 적절한 I/O 유형을 선택합니다. SSD 캐시를 마우스 오른쪽 단추로 클릭하고 Change I/O Type(I/O 유형 변경)을 선택하고 적절한 I/O 유형을 선택합니다.
• 응답 시간 • 캐시 적중 % 6. Start(시작)를 클릭하여 성능 모델링 도구를 실행합니다. 노트: 캐시 용량과 워크로드에 따라 캐시를 완전히 채우는 데 10-20시간 정도 걸릴 수 있습니다. 몇 분 정도 실행한 후에도 유 효한 정보가 제공되지만 가장 정확한 예측을 위해서는 몇 시간 정도 시간이 지나야 합니다. 노트: 성능 모델링 도구가 실행 중인 동안에 진행률 표시줄이 창의 기본 영역에 표시됩니다. 창을 닫거나 최소화해도 성능 모 델링이 계속해서 실행됩니다. MD 스토리지 관리자를 닫아도 성능 모델링 세션이 계속해서 실행됩니다. 노트: 상승 시간이 시작되는 시점에서는 SSD 캐시가 활성화되지 않았을 때보다 성능이 떨어질 수 있습니다. 7. 성능 모델링 세션의 결과를 저장하려면 Save As(다른 이름으로 저장)를 클릭하고 데이터를 .csv 파일로 저장합니다.
10 Premium 기능 - 스냅샷 가상 디스크 다음 가상 디스크 스냅샷 프리미엄 기능이 MD 스토리지 어레이에서 지원됩니다. • 다중 시점(PiT: point-in-time) 그룹을 사용하는 스냅샷 가상 디스크 스냅샷 이미지는 특정 시점(poin-in-time)(복원 지점이라고 함)에 생성된 연결된 기본 가상 디스크의 콘텐츠에 대한 논리 이미지입니 다. 스냅샷 이미지가 기본 가상 디스크에서 데이터를 저장하는 데 사용되기 때문에 이러한 유형의 이미지는 호스트로 직접 읽거나 쓸 수 없습니다. 호스트가 스냅샷 이미지에 있는 데이터의 복사본에 액세스할 수 있도록 허용하려면 스냅샷 가상 디스크를 생성해야 합 니다. 이 스냅샷 가상 디스크에는 호스트 응용 프로그램에서 참조된 스냅샷 이미지에 영향을 주지 않고 수정한 이후의 내용을 저장하 기 위해 사용되는 고유한 저장소가 포함됩니다.
스냅샷 그룹 및 정합성 보장 그룹 스냅샷 가상 디스크 프리미엄 기능은 다음 유형의 스냅샷 그룹을 지원합니다. • • 스냅샷 그룹 — 스냅샷 그룹은 연결된 단일 기본 가상 디스크의 시점(point-in-time)의 모음입니다. 일관성 그룹 — 일관성 그룹은 하나의 엔터티로 관리할 수 있는 가상 디스크의 그룹입니다. 일관성 그룹에서 수행하는 작업은 그 룹의 모든 가상 디스크에서 동시에 수행됩니다. 스냅샷 그룹 스냅샷 그룹의 목적은 성능에 영향을 주지 않고 지정된 기본 가상 디스크에서 스냅샷 이미지의 순서를 생성하는 것입니다. 향후 특정 시간이나 정기적으로 스냅샷 이미지를 자동 생성하도록 스냅샷 그룹에 대한 일정을 설정할 수 있습니다. 스냅샷 그룹을 생성할 때 다음 규칙이 적용됩니다. • • • • • 스냅샷 그룹은 스냅샷 이미지를 사용하거나 사용하지 않고 생성할 수 있습니다. 각 스냅샷 이미지는 스냅샷 그룹 하나의 구성원만 될 수 있습니다.
정합성 보장 그룹 저장소 일관성 그룹은 여러 가상 디스크의 동시 스냅샷으로 구성됩니다. 일관성 그룹에 포함되는 각 가상 디스크를 구성원 가상 디스크라고 합니다. 일관성 그룹에 가상 디스크를 추가하면 시스템에서 이 구성원 가상 디스크에 해당하는 새 스냅샷 그룹을 자동으로 생성합니 다. 그룹의 모든 스냅샷 이미지에 대한 데이터를 저장하기 위해서는 일관성 그룹의 각 구성원 가상 디스크에 대해 일관성 그룹 저장소 를 생성해야 합니다. 일관성 그룹 스냅샷 이미지는 여러 개의 스냅샷 가상 디스크로 구성됩니다. 목적은 동시에 각 구성원 가상 디스크를 위해 작성한 스냅 샷 이미지에 대해 호스트 액세스를 제공하는 것입니다. 일관성 그룹 스냅샷 이미지는 호스트에 직접 읽기 또는 쓰기 액세스가 불가능 합니다. 기본 가상 디스크에서 캡처한 데이터를 저장하는 용도로만 사용됩니다. 일관성 그룹 스냅샷 가상 디스크는 읽기 전용 또는 읽 기-쓰기로 지정할 수 있습니다.
스냅샷 그룹이 기본 가상 디스크에 있거나 기본 가상 디스크에 이미 최대 개수의 스냅샷 그룹이 있는 경우, 기본적으로 An Existing Snapshot Group(기존 스냅샷 그룹) 라디오 버튼이 선택됩니다. 3단계로 이동합니다. • 기본 가상 디스크에 스냅샷 그룹이 포함되어 있으면 There are no existing snapshot groups on this base virtual disk. Use the option below to create a new snapshot group 메시지가 표시됩니다. 계속하려면 기본 가상 디스크에서 스냅샷 그룹을 생성해야 합니다. 4단계로 이동합니다. 3. 기존 스냅샷 그룹에서 스냅샷 이미지를 생성하려면 다음을 수행합니다. • a. 기존 스냅샷 그룹 표에서 스냅샷 그룹을 선택합니다. 노트: 스냅샷 이미지의 최대 한도에 도달하지 않은 스냅샷 그룹을 선택해야 합니다. b.
• 순서 번호 및 생성 타임스탬프가 같은 여러 스냅샷 이미지 정합성 보장 그룹에서 스냅샷 이미지가 삭제되면 시스템에서 다음 작업을 수행합니다. • • • • 스토리지 어레이에서 스냅샷 이미지를 삭제합니다. 일관성 그룹 안에서 다시 사용하기 위한 저장소의 예비 공간을 해제합니다. 하나 이상의 삭제된 스냅샷 이미지와 연결된 멤버 가상 디스크를 Stopped(중지됨) 상태로 이동합니다. 하나 이상의 삭제된 스냅샷 이미지와 연결된 멤버 스냅샷 가상 디스크를 비활성화합니다. 스냅샷 이미지를 삭제하려면 다음을 수행합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 스냅샷 그룹이나 일관성 그룹에서 삭제하려는 스냅샷 이미지를 선택한 후 다음 메뉴 경로 중 하나를 선택하여 스냅샷 이미지를 삭제합니다.
4. 스냅샷 그룹에 대한 일정을 생성하는 경우 Create the First Snapshot Image Now(첫 번째 스냅샷 이미지 지금 생성)를 선택하 여 연결된 기본 가상 디스크의 복사본을 일정이 생성될 때 동시에 생성합니다. 5. 일관성 그룹에 대한 일정을 생성하는 경우 Enable snapshot image scheduling(스냅샷 이미지 일정 설정 활성화)을 클릭하여 그 룹에 대해 일정이 설정된 스냅샷 이미지 생성을 활성화합니다. 6. Finish(마침)를 클릭하여 선택한 스냅샷 그룹 또는 일관성 그룹에 대한 일정을 생성합니다. 시스템에서 다음을 수행합니다. • • 스냅샷 그룹 및 일관성 그룹에 대한 일정을 생성하고 스냅샷 그룹 또는 일관성 그룹에 대한 Properties(속성) 창을 업데이트 합니다. Create the First Snapshot Image Now(첫 번째 스냅샷 이미지 지금 생성)를 선택한 경우 시스템이 연결된 기본 가상 디스크 의 복사본을 작성합니다.
• • • • ○ 롤백 작업에 참여 중은 기본 가상 디스크의 새 스냅샷 이미지 생성 ○ 연결된 스냅샷 그룹의 저장소 전체 정책 변경 스토리지 어레이에서 이 작업이 진행 중인 동안에는 롤백 작업을 시작할 수 없습니다. ○ 디스크 그룹의 용량 확장 ○ 가상 디스크의 용량을 늘리기 위한 VDE(가상 디스크 확장) ○ 디스크 그룹을 다른 RAID 수준으로 마이그레이션 ○ 가상 디스크의 세그먼트 크기 변경 기본 가상 디스크가 가상 디스크 복사에 참여 중인 경우에는 롤백 작업을 시작할 수 없습니다. 기본 가싱 디스크가 원격 복제에서 보조 가상 디스크인 경우 롤백 작업을 시작할 수 없습니다. 그러나 기본 가상 디스크가 원격 복 제의 기본 가상 디스크인 경우에는 롤백 작업을 시작할 수 있습니다. 또한 기본 가상 디스크가 롤백 작업에 참여 중인 경우에는 원 격 복제에서 역할 바꾸기를 수행할 수 없습니다. 연결된 스냅샷 저장소 가상 디스크에서 사용된 용량에 인식 불가능한 섹터가 있으면 롤백 작업이 실패합니다.
스냅샷 이미지 롤백 취소 롤백 작업을 시작한 후에 취소하려면 Cancel Rollback(롤백 취소) 옵션을 사용합니다. 진행 중인 활성 롤백(현재 데이터 복사 중), 보 류 중인 롤백(리소스가 시작되기를 기다리는 보류 대기열에 있음) 또는 오류로 인해 일시 중지된 롤백을 취소할 수 있습니다. 진행 중 인 롤백 작업을 취소하면 기본 가상 디스크가 사용할 수 없는 상태로 되돌아가고 MD 스토리지 관리자에 실패한 것으로 나타납니다. 따라서 기본 가상 디스크의 콘텐츠를 복원하기 위한 복구 옵션이 존재할 경우에만 롤백 작업 취소를 고려하십시오. 롤백 작업을 취소한 후에 다음 작업 중 하나를 수행해야 합니다. • • 기본 가상 디스크의 콘텐츠를 다시 초기화합니다. 새 롤백 작업을 수행하여 기본 가상 디스크를 복원합니다(Cancel Rollback(롤백 취소) 작업에서 사용한 것과 같은 스냅샷 이미지 또는 새 롤백 작업을 수행하기 위한 다른 스냅샷 이미지 사용).
• 기본 가상 디스크 또는 정합성 보장 그룹의 멤버 가상 디스크의 정합성 보장 그룹을 선택한 후 Copy Services(복사 서비스) > Snapshot Image(스냅샷 이미지) > Rollback(롤백) > Change Priority(우선 순위 변경)를 선택합니다. Change Rollback Priority(롤백 우선 순위 변경) 창이 표시됩니다. 3. Rollback priority(롤백 우선 순위) 영역에서 슬라이드 바를 사용하여 롤백 작업의 우선 순위를 설정합니다. 일관성 그룹 스냅샷 이미지의 우선 순위를 변경하는 경우 우선 순위 설정이 선택한 일관성 그룹의 모든 구성원 가상 디스크에 적 용됩니다. 4. Change(변경)를 클릭하여 변경 내용을 롤백 우선 순위에 적용합니다. 스냅샷 그룹 생성 스냅샷 그룹은 연결된 단일 기본 가상 디스크의 시점(point-in-time) 이미지의 순서입니다. 스냅샷 그룹은 저장소를 사용하여 그룹에 포함된 모든 스냅샷 이미지에 대한 데이터를 저장합니다.
로 생성합니다. 그룹에 포함된 모든 스냅샷 이미지에 대해 데이터를 저장하려면 일관성 그룹의 모든 구성원 가상 디스크마다 하나의 일관성 그룹 저장소를 생성해야 합니다. Manual(수동) 방법은 고급으로 간주되며 물리 디스크 증복성, 프로비저닝 및 최적의 물리 디스크 구성을 이해하는 사용자만이 이 방 법을 사용해야 합니다. 일관성 그룹의 이름을 지정할 때 다음 지침을 숙지하십시오. • • • 일관성 그룹 저장소에는 구성에 따라 최소 필수 용량이 있습니다. 저장소에 대해 용량 요구 사항을 정의할 경우 이 디스크 그룹이나 디스크 풀에 있는 기타 가상 디스크에 대해 적용될 수 있는 향후 요구 사항에 유의하십시오. 데이터 스토리지 요구 사항을 충족하기 위한 충분한 용량이 있는지 확인하되 스토리지 어레이에 있는 모든 스토리지를 빠르게 소모할 수 있으므로 과도하게 할당해서는 안 됩니다. 저장소 후보 목록에는 기존 및 새 저장소 가상 디스크가 모두 포함될 수 있습니다.
1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 스냅샷 그룹 범주 노드에서 변경하려는 스냅샷 그룹을 선택한 후 Copy Services(복사 서비스) > Snapshot Group(스냅샷 그룹) > Change Settings(설정 변경)를 선택합니다. Change Snapshot Group Settings(스냅샷 그룹 설정 변경) 창이 표시됩니다. 3. 필요에 따라 스냅샷 그룹 설정을 변경합니다. 4. OK(확인)를 클릭하여 스냅샷 그룹에 변경 내용을 적용합니다. 스냅샷 그룹 이름 바꾸기 스냅샷 그룹의 현재 이름이 더 이상 의미가 없거나 적용 가능하지 않을 경우 이름을 변경하려면 Rename Snapshot Group(스냅샷 그 룹 이름 바꾸기) 옵션을 사용합니다. 스냅샷 그룹의 이름을 지정할 때 다음 지침을 숙지하십시오.
3. 읽기-쓰기 스냅샷 가상 디스크에 대해 저장소를 생성할 방법을 선택합니다. 다음 중 하나를 수행합니다. 기본 용량 설정으로 스냅샷 가상 디스크 저장소를 생성하려면 Automatic(자동)을 선택합니다. 권장되는 옵션입니다. 스냅샷 가상 디스크 저장소에 대한 속성을 정의하려면 Manual(수동)을 선택합니다. 스냅샷 가상 디스크 저장소에 대해 사용 자 지정 가능한 모든 설정을 지정하려는 경우 이 옵션을 사용합니다. Manual(수동) 방법은 고급으로 간주되며 물리 디스크 일 관성과 최적의 물리 디스크 구성을 이해하는 사용자만이 이 방법을 사용해야 합니다. 4. Convert(변환)를 클릭하여 읽기 전용 스냅샷 가상 디스크를 읽기-쓰기로 변환합니다. 스냅샷 가상 디스크 또는 일관성 그룹 구성원의 스냅샷 가상 디스크 표가 Mode(모드) 열 아래에 읽기-쓰기로 표시되고 Repository(저장소) 열이 채워집니다.
• Add members later(나중에 구성원 추가)를 선택한 후 Finish(마침)를 클릭하여 구성원 가상 디스크 없이 일관성 그룹을 생성 합니다. 6단계로 이동합니다. Eligible virtual disks(자격 있는 가상 디스크) 표에는 일관성 그룹에서 사용할 수 있는 가상 디스크만 표시됩니다. 일관성 그룹의 구성원이 되기 위해서는 가상 디스크가 Failed(실패) 상태에 있을 수 없으며 포함된 가상 디스크가 연결된 스냅샷 그룹에 허용되는 최대 개수보다 작아야 합니다. 5. 일관성 그룹의 각 구성원에 대해 저장소를 생성할 방법을 선택합니다. 기본 용량 설정으로 저장소를 생성하려면 Automatic(자동)을 선택하고 Finish(마침)를 클릭합니다. 이 옵션이 권장됩니다. Manual(수동)을 선택하고 Next(다음)를 클릭하여 저장소의 용량 설정을 정의한 후 Finish(마침)를 클릭하여 일관성 그룹 생 성 프로세스를 계속합니다.
b. 확인을 클릭합니다. 8. View advanced options(고급 옵션 보기)를 선택한 후 다음 기본 설정을 적절하게 수락하거나 변경합니다. 9. Finish(마침)를 클릭합니다. 정합성 보장 그룹 이름 바꾸기 일관성 그룹의 현재 이름이 더 이상 의미가 없거나 적용 가능하지 않을 경우 이름을 변경하려면 Rename Consistency Group(일관성 그룹 이름 바꾸기) 옵션을 사용합니다. 일관성 그룹의 이름을 지정할 때 다음 지침을 숙지하십시오. • • • • • 이름에 문자, 숫자, 특수 문자인 밑줄(_), 하이픈(-), 파운드 부호(#)를 사용할 수 있습니다. 다른 문자를 사용하면 오류 메시지와 함께 다른 이름을 선택하라는 메시지가 표시됩니다. 이름은 30자로 제한합니다. 이름의 앞뒤에 붙은 공백은 모두 삭제됩니다. 쉽게 알아보고 기억할 수 있는 고유하고 의미 있는 이름을 사용합니다. 임의의 이름이나 나중에 빠르게 의미가 사라질 수 있는 이름은 피합니다.
• Reject writes to base virtual disk(기본 가상 디스크에 대한 쓰기 거부) — 저장소가 정의된 최대 비율에 도달하면 시스템이 저 장소 액세스를 트리거한 기본 가상 디스크에 대한 I/O 쓰기 요청을 거부합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 일관성 그룹 범주 노드에서 변경하려는 일관성 그룹을 선택한 후 Copy Services(복사 서비스) > Snapshot Group(스냅샷 그룹) > Change Settings(설정 변경)를 선택합니다. Change Consistency Group Settings(일관성 그룹 설정 변경) 창이 표시됩니다. 3. 필요에 따라 일관성 그룹 설정을 변경합니다. 4. OK(확인)를 클릭하여 일관성 그룹에 변경 내용을 적용합니다.
2. 다음 중 하나를 수행합니다. 정합성 보장 그룹에서 제거하려는 기본 가상 디스크를 선택한 후 Storage(스토리지) > Virtual disk(가상 디스크) > Remove From Consistency Group(정합성 보장 그룹에서 제거)을 선택합니다. • 구성원 가상 디스크를 추가할 일관성 그룹을 선택한 후 Copy Services(복사 서비스) > Consistency Group(일관성 그룹) > Remove Member Virtual Disks(구성원 가상 디스크 제거)를 선택합니다. 3. 여러 일관성 그룹의 구성원인 기본 가상 디스크를 선택하거나 구성원 가상 디스크를 제거할 일관성 그룹을 선택한 경우 다음 중 하나를 수행합니다. • • Consistency groups(일관성 그룹) 표에서 기본 가상 디스크를 제거하려는 하나 의상의 일관성 그룹을 선택한 후 Remove(제 거)를 클릭합니다.
• 새 스냅샷 이미지(기존 스냅샷 그룹에 있음)를 선택한 후 기존 스냅샷 그룹 표에서 스냅샷 그룹을 선택한 후 Next(다음)를 클 릭합니다. Snapshot Virtual Disk Settings(스냅샷 가상 디스크 설정) 창이 표시됩니다. 4. Snapshot virtual disk name(스냅샷 가상 디스크 이름) 필드에 이 스냅샷 이미지에 대해 선택한 가상 디스크를 가장 적절하게 설 명하는 고유한 이름(최대 30자)을 입력합니다(예: AccountingData). 기본적으로 스냅샷 가상 디스크 이름은 이름 입력란에 [base-virtual disk-name] - SV + sequence-number와 같이 표시됩니다. 이 예에서 SV(스냅샷 가상 디스크)는 추가된 접미사이고 순서-번호는 기본 가상 디스크에 상대적인 스냅샷 가상 디스크의 시간 순서상의 번호입니다.
• • • 스냅샷 그룹 저장소에는 구성에 따라 최소 필수 용량이 있습니다. 저장소에 대한 용량 요구 사항을 정의할 때 이 디스크 그룹이나 디스크 풀의 다른 가상 디스크에 대해 적용될 수 있는 향후 요구 사항을 유의하십시오. 시스템의 스토리지를 차지하는 용량을 너무 많이 할당하지 않고 데이터 스토리지 요구 사항을 만족할 수 있도록 충분한 용량이 있는지 확인합니다. 저장소 후보의 목록에는 기존 및 새 저장소 가상 디스크가 모두 포함될 수 있습니다. 기존 저장소 가상 디스크는 목록 맨 위에 있 습니다. 기존 저장소 가상 디스크를 다시 사용하면 새로 생성할 때 발생하는 초기화 프로세스를 피할 수 있다는 이점이 있습니다. 스냅샷 가상 디스크 저장소를 생성하려면 다음 단계를 따르십시오. 1. Snapshot Virtual Disk Settings(스냅샷 가상 디스크 설정) 창에서 Manual(수동)을 선택하고 Next(다음)를 클릭하여 스냅샷 가 상 디스크 저장소에 대한 속성을 정의합니다.
• • 스냅샷 가상 디스크 또는 현재 스냅샷 이미지와 일관성 그룹 스냅샷 가상 디스크의 연결을 제거합니다. 일관성 그룹 스냅샷 가상 디스크의 경우 각 구성원의 스냅샷 가상 디스크를 비활성화합니다. 노트: 스냅샷 가상 디스크 또는 정합성 보장 그룹의 스냅샷 가상 디스크가 완료되었고 나중에 다시 생성하지 않으려면 가상 디스 크를 비활성화하는 대신 삭제해야 합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 비활성화하려는 스냅샷 가상 디스크 또는 일관성 그룹 스냅샷 가상 디스크를 선택한 후 다음 중 하나를 선택합니다. Copy Services(복사 서비스) > Snapshot Virtual disk(스냅샷 가상 디스크) > Disable(비활성화) Confirm Disable Snapshot Virtual Disk(스냅샷 가상 디스크 비활성화 확인) 창이 표시됩니다.
일관성 그룹의 이름을 지정할 때 다음 지침을 숙지하십시오. • • • 이름은 30자로 제한합니다. 이름의 앞뒤에 붙은 공백은 모두 삭제됩니다. 쉽게 알아보고 기억할 수 있는 고유하고 의미 있는 이름을 사용합니다. 임의의 이름이나 나중에 빠르게 의미가 사라질 수 있는 이름은 피합니다. 노트: 스냅샷 가상 디스크 또는 일관성 그룹 스냅샷 가상 디스크의 이름을 다른 가상 데스크에서 이미 사용 중인 이름으로 바꾸려 하면 오류 메시지가 표시되며 다른 이름을 선택하라는 메시지가 표시됩니다. 스냅샷 가상 디스크 또는 일관성 그룹 스냅샷 가상 디스크의 이름을 바꾸려면 다음 단계를 따르십시오. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 비활성화하려는 스냅샷 가상 디스크 또는 일관성 그룹 스냅샷 가상 디스크를 선택한 후 다음 중 하나를 선택합니다.
기본적으로 정합성 보장 그룹 스냅샷 가상 디스크 이름은 이름 입력란에 [consistency-group-name] - SV + sequencenumber와 같이 표시됩니다. 여기서 SV(스냅샷 가상 디스크)는 추가된 접미사이고 순서-번호는 정합성 보장 그룹에 상대적인 스 냅샷 가상 디스크의 시간 순서상의 번호입니다. 예를 들어, “Accounting”이라는 일관성 그룹에 대한 첫 번째 스냅샷 가상 디스크를 생성할 경우 스냅샷 가상 디스크의 기본 이름은 “Accounting_SV_01”입니다. “Accounting”을 기반으로 생성한 다음 스냅샷 가상 디스크의 기본 이름은 “Accounting_SV_02”입니 다. 30자 한도가 있습니다. 이 한도에 도달한 후에는 텍스트 상자에 더 이상 입력할 수 없습니다. 일관성 그룹 이름이 30자이면 그룹에 대한 기본 이름이 접미사 “SV” 및 순서 문자열을 추가할 수 있도록 충분하게 잘린 기본 가상 디스크 이름을 사용합니다. 5.
• • 저장소에 대해 용량 요구 사항을 정의할 경우 이 디스크 그룹이나 디스크 풀에 있는 기타 가상 디스크에 대해 적용될 수 있는 향후 요구 사항에 유의하십시오. 데이터 스토리지 요구 사항을 충족하기 위한 충분한 용량이 있는지 확인하되 스토리지 어레이에 있는 모든 스토리지를 빠르게 소모할 수 있으므로 과도하게 할당해서는 안 됩니다. 저장소 후보 목록에는 기존 및 새 저장소 가상 디스크가 모두 포함될 수 있습니다. 기존 저장소 가상 디스크는 일관성 그룹 스냅샷 가상 디스크를 삭제할 경우에 기본적으로 스토리지 어레이에 남아 있습니다. 기존 저장소 가상 디스크는 목록 맨 위에 놓입니다. 기존 저장소 가상 디스크를 다시 사용하면 새로 생성할 경우에 발생하는 초기화 프로세스를 피할 수 있다는 이점이 있습니다. 일관성 그룹 스냅샷 가상 디스크 저장소를 생성하려면 다음 단계를 따르십시오. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2.
• • • 호스트 매핑 및 액세스를 유지합니다. 읽기-쓰기 요청은 실패합니다. 스냅샷 가상 디스크 또는 현재 스냅샷 이미지와 일관성 그룹 스냅샷 가상 디스크의 연결을 제거합니다. 일관성 그룹 스냅샷 가상 디스크의 경우 각 구성원의 스냅샷 가상 디스크를 비활성화합니다. 노트: 스냅샷 가상 디스크 또는 정합성 보장 그룹의 스냅샷 가상 디스크가 완료되었고 나중에 다시 생성하지 않으려면 가상 디스 크를 비활성화하는 대신 삭제해야 합니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 비활성화하려는 스냅샷 가상 디스크 또는 일관성 그룹 스냅샷 가상 디스크를 선택한 후 다음 중 하나를 선택합니다. Copy Services(복사 서비스) > Snapshot Virtual disk(스냅샷 가상 디스크) > Disable(비활성화) Confirm Disable Snapshot Virtual Disk(스냅샷 가상 디스크 비활성화 확인) 창이 표시됩니다.
• • • • 스냅샷 그룹 스냅샷 가상 디스크 일관성 그룹 구성원 가상 디스크 복제된 쌍 노트: 이 옵션을 사용하여 수정 우선 순위를 변경하면 선택한 전체 저장소의 우선 순위만 수정됩니다. 설정은 전체 저장소 내에 포함된 모든 개별 저장소 가상 디스크에 적용됩니다. 수정 우선 순위를 변경하려면 다음 단계를 따르십시오. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 수정 우선 순위를 변경하려는 스토리지 개체를 선택합니다. 3. 선택한 스토리지 객체를 마우스 오른쪽 버튼으로 클릭하고 Overall Repository(전체 저장소) > Change Modification Priority(수정 우선 순위 변경)를 선택합니다. Change Disk Pool Settings(디스크 풀 설정 변경) 창이 표시됩니다. 4.
• 복제된 쌍 다음 지침이 적용됩니다. • • • Pre-Read Consistency Check(미리 읽기 일관성 검사) 설정을 변경하면 선택한 전체 저장소에 대해서만 설정이 수정됩니다. Pre-Read Consistency Check(미리 읽기 일관성 검사) 설정은 전체 저장소 내에 포함된 모든 개별 저장소 가상 디스크에 적용됩 니다. 미리 읽기로 구성된 전체 저장소 가상 디스크가 일관성 정보를 유지 관리하지 않는 RAID 수준으로 마이그레이션되면 전체 저장소 가상 디스크의 메타데이터에 미리 읽기가 활성화된 것으로 계속해서 표시됩니다. 그러나 해당 저장소 가상 디스크에 대한 읽기는 일관성 미리 읽기를 무시합니다. 가상 디스크가 이후에 일관성을 지원하는 RAID 수준으로 다시 마이그레이션되면 옵션을 다시 사 용할 수 있게 됩니다. 일관성 그룹 스냅샷 가상 디스크를 생성하려면 다음 단계를 따르십시오. 1.
• • 하나 이상의 기존 저장소 가상 디스크 추가 디스크 그룹이나 디스크 풀에서 사용할 수 있는 여유 용량을 사용하여 저장소 가상 디스크 생성 노트: 디스크 그룹이나 디스크 풀에 여유 용량이 존재하지 않으면 사용되지 않은 물리 디스크 형태로 구성되지 않은 용량을 디스크 그룹이나 디스크 풀에 추가할 수 있습니다. 다음 조건 중 하나가 존재할 경우에는 전체 저장소의 스토리지 용량을 늘릴 수 없습니다.
전체 저장소의 용량 줄이기 전체 저장소에는 여러 저장소 가상 디스크가 포함될 수 있습니다. 다음 스토리지 개체에 대한 기존 전체 저장소의 스토리지 용량을 줄이려면 Decrease Capacity(용량 줄이기) 옵션을 사용합니다. • • • • • 스냅샷 그룹 스냅샷 가상 디스크 일관성 그룹 구성원 가상 디스크 일관성 그룹 구성원 스냅샷 가상 디스크 복제된 쌍 가상 디스크 다음 조건 중 하나가 존재할 경우에는 전체 저장소의 스토리지 용량을 줄일 수 없습니다. • • • 전체 저장소에 하나의 저장소 구성원 가상 디스크만 포함되어 있는 경우 전체 저장소와 연결된 스냅샷 이미지가 하나 이상 있는 경우 스냅샷 가상 디스크 또는 일관성 그룹 구성원 스냅샷 가상 디스크가 비활성화되어 있는 경우 다음 지침이 적용됩니다. • • • • 저장소 구성원 가상 디스크는 추가한 순서의 반대 순서로만 제거할 수 있습니다. 전체 저장소에는 최소 하나의 저장소 구성원 가상 디스크가 있어야 합니다.
노트: 디스크 그룹이나 디스크 풀에 여유 용량이 존재하지 않으면 사용되지 않은 물리 디스크 형태로 구성되지 않은 용량을 디스크 그룹이나 디스크 풀에 추가할 수 있습니다. 주의: 오류가 여전히 발생하는 경우에 Revive(복구) 옵션을 사용하면 데이터 손상 또는 데이터 손실이 발생할 수 있으며 스 토리지 객체가 Failed(실패) 상태로 돌아갑니다. 1. AMW에서 Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택합니다. 2. 복구하려는 스토리지 객체를 선택한 후 선택한 스토리지 객체에 따라 다음 메뉴 경로 중 하나를 선택합니다.
11 Premium 기능 - 가상 디스크 복사 노트: 가상 디스크 복사는 대상 가상 디스크의 데이터를 덮어씁니다. 가상 디스크 복사를 시작하기 전에 데이터가 더 이상 필요 없는지 확인하거나 대상 가상 디스크의 데이터를 백업하십시오. 노트: 이 기능을 주문하면 Dell PowerVault MD Series 스토리지 어레이와 동일한 포장 상자에 프리미엄 기능 활성화 카드가 배 송됩니다. 카드의 지침에 따라 키 파일을 확보하여 기능을 활성화할 수 있습니다. 노트: 가상 디스크 복사를 생성하는 기본적인 방법은 스냅샷 가상 디스크에서 복사하는 것입니다. 이 방법을 사용하면 스냅샷을 가상 디스크 복사 작업의 원본으로 사용하고 스냅샷 작업에 사용된 원래 가상 디스크를 읽기/쓰기 작업에 사용할 수 있습니다. 가상 디스크 복사를 생성하는 경우 같은 스토리지 어레이에 원본 가상 디스크와 대상 가상 디스크로 구성된 복사 쌍을 만듭니다. 원본 가상 디스크는 복사하려는 데이터를 포함하는 가상 디스크입니다.
가상 디스크 복사 유형 오프라인 또는 온라인 가상 디스크 복사를 수행할 수 있습니다. 두 유형의 가상 디스크 복사 작업 중에는 데이터 무결성을 유지하기 위해 대상 가상 디스크의 모든 I/O이 일시 중지됩니다. 가상 디스크 복사가 완료되면 대상 가상 디스크는 호스트에 대해 자동으로 읽 기 전용이 됩니다. 오프라인 복사 오프라인 복사는 복사가 진행 중일 때 소스 가상 디스크의 모든 업데이트를 일시 중지하고, 소스 가상 디스크의 데이터를 읽고 이를 대상 가상 디스크에 복사합니다. 오프라인 가상 디스크 복사에서, 복사 관계는 소스 가상 디스크와 대상 가상 디스크 간에 있습니다. 오프라인 복사에 참여하는 소스 가상 디스크는 가상 디스크 복사가 In Progress(진행 중) 또는 Pending(보류 중) 상태로 표시되어 있는 동안에 읽기 요청에 사용할 수 있습니다. 쓰기 요청은 오프라인 복사가 완료된 후에만 허용됩니다.
가상 디스크 복사 제한 사항 가상 디스크 복사 작업을 수행하기 전에 이 섹션에 설명된 제한 사항을 이해하고 준수해야 합니다. 이러한 제한 사항은 원본 가상 디 스크, 대상 가상 디스크 및 스토리지 어레이에 적용됩니다. • • • • • • • 가상 디스크 복사가 In Progress(진행 중), Pending(보류 중) 또는 Failed(실패) 상태일 때 원본 가상 디스크는 읽기 I/O 작업에만 사 용할 수 있습니다. 가상 디스크 복사가 완료되면 원본 가상 디스크의 읽기 및 쓰기 I/O 작업이 허용됩니다. 한 번에 하나의 가상 디스크 복사에 대해서만 가상 디스크를 대상 가상 디스크로 선택할 수 있습니다. 가상 디스크에 대한 가상 디스크 복사를 원본 가상 디스크와 동일한 호스트에 장착할 수는 없습니다. Windows에서는 가상 디스크 복사본에 물리 디스크 문자를 할당할 수 없습니다. Failed(실패) 상태의 가상 디스크는 원본 가상 디스크 또는 대상 가상 디스크로 사용할 수 없습니다.
시작하기 전에 대상 가상 디스크와 연관된 스냅샷 가상 디스크가 있을 경우 가상 디스크 복사에 실패합니다. 스냅샷 가상 디스크의 소스 가상 디스크 를 선택하는 경우, 소스 가상 디스크와 연관된 모든 스냅샷 가상 디스크를 비활성화해야 대상 가상 디스크로 선택할 수 있습니다. 그 렇지 않으면 소스 가상 디스크를 대상 가상 디스크로 사용할 수 없습니다. 가상 디스크 복사는 대상 가상 디스크의 데이터를 덮어쓰며 대상 가상 디스크를 호스트에 대해 읽기 전용으로 만듭니다. In Progress(진행 중) 상태의 가상 디스크 복사가 8개 있는 경우, 이후의 모든 가상 디스크 복사의 상태는 Pending(보류 중)이 되며 이 러한 상태는 8개의 가상 디스크 복사 중 1개가 완료될 때까지 유지됩니다.
복사 관리자 복사 생성 마법사를 사용하여 가상 디스크 복사를 생성한 후, 복사 관리자를 통해 가상 디스크 복사를 모니터링할 수 있습니다. 복사 관리자에서 가상 디스크 복사를 재복사, 중지 또는 제거합니다. 또한 복사 우선순위 및 대상 가상 복사의 Read-Only 특성과 같은 특성 을 수정할 수 있습니다. 복사 관리자에서 가상 디스크 복사의 상태를 볼 수 있습니다. 가상 디스크 복사에 포함되는 가상 디스크를 결 정하려는 경우 복사 관리자 또는 스토리지 배열 프로파일을 사용할 수 있습니다. 가상 디스크 복사 Create Copy Wizard(복사 생성 마법사)를 사용하여 가상 디스크 복사를 생성할 수 있습니다. 가상 디스크 복사가 수행되면 호스트에 대해 대상 가상 디스크가 자동으로 읽기 전용이 됩니다. 대상 가상 디스크의 데이터를 보존하려면 이 특성을 활성 상태로 유지해야 합 니다.
복사 우선 순위 설정 Copy Manager(복사 관리자)를 사용하여 선택된 복사 쌍에 대해 가상 디스크 복사가 완료되는 순위를 선택할 수 있습니다. 다음과 같 은 시점에서 복사 쌍의 복사 우선순위를 변경할 수 있습니다. • • • 가상 디스크 복사가 시작되기 전 가상 디스크 복사가 In Progress(진행 중) 상태일 때 가상 디스크 복사를 재생성할 때 복사 우선순위를 설정하려면 다음을 수행합니다. 1. AMW에서, Storage & Copy Services(스토리지 및 복사 서비스) 탭을 선택하고 Copy Services(복사 서비스) > Virtual Disk Copy(가상 디스크 복사) > Manage Copies(복사 관리)를 선택합니다. Copy Manager(복사 관리자) 창이 표시됩니다. 2. 표에서, 1개 이상의 복사 쌍을 선택합니다. 3. Change(변경) > Copy Priority(복사 우선순위)를 선택합니다.
노트: Windows에서 관련 가상 디스크의 물리적 디스크 문자를 제거하거나 Linux에서 가상 물리적 디스크를 마운트 해제하면 가 상 디스크 복사에서 안정적으로 물리적 디스크 복사를 수행할 수 있습니다. 기존 복사 쌍에 사용되는 새 가상 디스크 복사를 생성하기 전에, 호스트 서버 및 다시 복사할 관련 가상 디스크가 올바른 상태에 있어 야 합니다. 다음 단계를 수행하여 호스트 서버 및 가상 디스크를 준비합니다. 1. 소스 및 대상 가상 디스크에 대한 모든 I/O 활동을 중지합니다. 2. Windows 시스템에서 소스 및 타겟 가상 디스크(마운트된 경우)의 캐시를 플러시합니다. 호스트에 프롬프트가 표시되면 SMrepassist -f 를 입력하고 키를 누릅니다. 자세한 내용은 SMrepassist 유틸리티를 참조하십시오. 3.
복사 쌍을 제거하려면 다음을 수행합니다. 1. AMW에서 Copy Services(복사 서비스) > Virtual Disk Copy(가상 디스크 복사) > Manage Copies(복사 관리)를 선택합니다. Copy Manager(복사 관리자) 창이 표시됩니다. 2. 표에서, 1개 이상의 복사 쌍을 선택합니다. 3. Copy(복사) > Remove Copy Pairs(복사 쌍 제거)를 선택합니다. Remove Copy Pairs(복사 쌍 제거) 대화상자가 표시됩니다. 4. Yes(예)를 클릭합니다.
12 Linux용 디바이스 매퍼 다중 경로 주제: • • • • • • • 개요 DMMP(Device Mapper Multipathing) 장치 사용 디바이스 매퍼 구성 단계 Linux 호스트 서버 재부팅 Best Practice 특수 파티션에 관한 중요 정보 제한 사항 및 알려진 문제 문제 해결 개요 MD Series 스토리지 어레이에서는 장치 매퍼(DM)라고 하는 Linux 운영 체제 소프트웨어 프레임워크를 사용하여 Linux 호스트 서버에 서 다중 경로 기능을 활성화합니다. DM 다중 경로 기능은 물리 디스크와 유틸리티의 조합으로 제공됩니다. 이 장에서는 이러한 유틸 리티를 사용하여 Linux 시스템에서 MD Series 스토리지 어레이를 활성화하는 과정에 대해 설명합니다.
4. MD 스토리지 관리자를 사용하여 가상 디스크 생성 및 매핑 - MDCU를 사용하여 어레이를 구성한 후에는 MD 스토리지 관리자를 실행하여 가상 디스크를 생성하고 매핑합니다. MD Storage Manager 사용 MD 스토리지 관리자를 사용하여 다음을 수행할 수 있습니다. 호스트 서버를 MD Series 스토리지 어레이에 매핑합니다. 가상 디스크를 생성합니다. 새로 생성한 어레이를 호스트 서버에 매핑합니다. • • • 노트: MDCU를 사용하여 구성된 모든 어레이는 EMW의 장치 목록에 자동으로 추가됩니다. 디바이스 매퍼 구성 단계 DM 다중경로 구성을 완료하고 스토리지를 Linux 호스트 서버에서 사용 가능하게 하려면 다음을 수행합니다. 1. 가상 디스크를 검색합니다. 새로 추가된 가상 디스크 검색을 참조하십시오. 2. 다중경로 장치 토폴로지를 표시합니다. 다중경로 명령을 사용하여 다중경로 장치 토폴로지 표시를 참조하십시오. 3. 다중경로 장치 노드에 파티션을 생성합니다.
의미는 다음과 같습니다. mpath1은 디바이스 매퍼에서 생성한 가상 디바이스의 이름으로, /dev/mapper 디렉토리에 있습니다. DELL은 디바이스의 공급업체입니다. MD3xxxx는 디바이스의 모델입니다. Sdc는 디바이스에 대한 독자적인 RAID의 물리적 경로입니다. Sdb는 디바이스에 대한 비독자적인 RAID의 물리적 경로입니다. 다음은 SLES 출력의 예입니다. mpathb(360080e500017b2f80000c6ca4a1d4ab8) dm-21 DELL,MD3xxxx[size=1.0G][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac][rw]\_ round-robin 0 [prio=6][active] \_ 4:0:0:22 sdx 65:112 [active][ready]\_ round-robin 0 [prio=1][enabled] \_ 6:0:0:22 sdcl 69:144 [active][ghost] 의미는 다음과 같습니다.
노트: 다중경로 지정이 가능한 장치에 파티션을 생성한 후 파일 시스템 생성, 원시 I/O 및 파일 시스템 I/O를 포함한 모든 I/O 작 업은 다중경로 지정 장치 노드가 아닌 파티션 노드를 통해 수행되어야 합니다. 디바이스 매퍼 파티션에 파일 시스템 생성 새로 생성된 디바이스 매퍼 파티션에 파일 시스템을 생성하려면 표준 mkfs 명령을 사용합니다. 예를 들어, 다음과 같습니다. # mkfs –t /dev/mapper/ 여기서, 는 파일 시스템이 생성되는 파티션입니다. 디바이스 매퍼 파티션 마운트 아래 제시된 바와 같이 장치 매퍼 파티션을 장착하려면 표준 mount 명령을 사용합니다. # mount /dev/mapper/ 사용 준비 현재 MD Series 스토리지 어레이에 새로 생성된 가상 디스크가 설정되어 사용할 수 있습니다.
표 15. 유용한 디바이스 매퍼 명령 (계속) 명령 multipath –ll multipath multipath –f multipath –F rescan_dm_devs 설명 사용 가능한 모든 정보를 사용하여 현재 다중 경로 토폴로지를 표시합니다(sysfs, device mapper, path checkers 등). 간소화된 출력을 사용하여 다중 경로 디바이스를 다시 집계합니다. 지정된 다중 경로 장치에 대해 장치 매퍼를 플러시합니다. 기본 물리 디스크가 삭제되거 나 매핑 해제되는 경우에 사용됩니다. 사용되지 않은 모든 다중 경로 장치 맵을 플러시합니다. Dell EMC에서 제공하는 스크립트입니다. 호스트 SCSI 버스를 강제로 재검색하고, 필요에 따라 다중 경로 디바이스를 집계합니다. 다음과 같은 경우에 이 명령을 사용합니다.
표 16. 문제 해결 (계속) 질문 응답 multipath –ll 명령으로 장치가 표시되지 않는 이 먼저 디바이스가 검색되는지 확인합니다. #cat /proc/scsi/scsi 명령을 실 유는 무엇입니까? 행하면 이미 검색된 모든 디바이스가 표시됩니다. multipath.conf 명령을 실행하 면 올바른 설정으로 업데이트되었는지 확인할 수 있습니다. 그런 다음, multipath 명령, multipath –ll 명령을 차례로 실행하면 새 디바이스가 표 시됩니다. 새로 매핑된 LUN이 다중 경로 디바이스 노드에 디렉토리에서 rescan_dm_devs를 실행하십시오. 이렇게 하면 디바이스가 표시 할당되지 않는 이유는 무엇입니까? 됩니다. LUN을 제거했지만 다중경로 매핑이 여전히 존 재합니다. LUN을 제거한 후에도 다중 경로 지정 디바이스는 여전히 존재합니다. 다중 경로 지정 매핑을 제거하려면 multipath –f 명령을 실행하십시오.
13 비대칭 논리 장치 액세스 구성 MD 시리즈 RAID 스토리지 배열에서 비대칭 논리 장치 액세스(ALUA)를 지원하는 경우, 활성-활성 처리량을 통해 RAID 컨트롤러 모듈 에서 RAID 컨트롤러가 소유하지 않은 가상 디스크로 I/O가 통과될 수 있습니다. ALUA 기능이 없을 경우, 특정 가상 디스크에 대상 지 정된 데이터 요청을 독자적 RAID 컨트롤러 모듈에 보내려면 호스트 다중경로 드라이버가 필요합니다. RAID 컨트롤러 모듈이 가상 디 스크를 소유하지 않은 경우 해당 요청을 거부합니다.
표 17. 다양한 스토리지 어레이의 어레이 PID 스토리지 어레이 array_PID MD3400 MD34xx MD3420 MD34xx MD3800i MD38xxi MD3820i MD38xxi MD3800f MD38xxf MD3820f MD38xxf MD3460 MD34xx MD3860i MD38xxi MD3860f MD38xxf 2. ESX 기반 호스트 서버를 다시 부팅합니다. VMware ESXi에서 ALUA 확인 설정한 SATP 클레임 규칙이 VMware ESXi에서 추가되었는지 확인하려면 ESXi 5.x에 다음 명령을 실행하십시오. # esxcli storage nmp satp rule list –s VMW_SATP_ALUA VMW_SATP_ALUA에 대한 클레임 규칙에 tpgs_on 플래그가 지정된 VID/PID = Dell/array_PID가 표시되는지 확인합니다. 호스트 서버가 MD 스토리지 어레이에 ALUA를 사용 중인지 확인 ESXi 5.
14 Premium 기능 - 원격 복제 다음 유형의 원격 복제가 MD 스토리지 어레이에서 지원됩니다. • • 원격 복제 — 시점(point-in-time) 이미지를 사용하여 로컬 및 원격 사이트 간 재동기화를 처리하기 위한 표준 비동기식 복제입니 다. 이러한 유형의 복제는 파이버 채널 및 iSCSI 스토리지 어레이 모두에서 지원되지만 이 둘 사이에서는 지원되지 않습니다. 원격 복제(레거시) — 로컬 및 원격 사이트 데이터를 실시간으로 동기화하는 동기식(또는 전체 쓰기) 복제입니다. 이러한 유형의 복제는 파이버 채널 스토리지 어레이에서만 지원됩니다.
원격 복제 기능 간 차이 (동기식) 원격 복제(레거시) 기능과 비교해 표준(비동기식 쓰기) 원격 복제 프리미엄 기능은 시점(point-in-time) 스냅샷 이미지를 사 용하여 원본 가상 디스크의 상태를 캡처하고 마지막 시점(point-in-time) 이미지 이후에 변경된 데이터만 작성합니다. 표준 원격 복제의 경우 원격 스토리지 어레이가 로컬 스토리지 어레이와 완벽하게 동기화되지 않습니다. 그 결과 원격 스토리지 어레 이에서 급격한 총체적 손실이 발생할 경우 일부 트랜잭션이 손실될 수 있습니다. 동기식 원격 복제(레거시)의 경우 원본 가상 디스크에 대한 모든 데이터 쓰기가 원격 가상 디스크로 복제됩니다. 이 절차는 프로덕션 데이터의 동일한 실시간 원격 가상 디스크를 만듭니다. 그 밖의 차이로 다음이 포함됩니다. • • • 필요한 저장소 가상 디스크의 개수 - 표준 원격 복제에서는 복제된 각 쌍(원격 가상 디스크에서 로컬 가상 디스크로)에 대해 저장 소 가상 디스크를 생성해야 합니다.
• • • 기본 가상 디스크는 가상 디스크 복사에서 원본 가상 디스크 또는 대상 가상 디스크가 될 수 있습니다. 보조 가상 디스크는 복사가 완료된 후에 역할 바꾸기가 시작되지 않은 이상 원본 가상 디스크가 될 수 없습니다. Copy in Progress(복사 진행 중) 상태 중에 역할 바꾸기가 시작되면 복사가 실패하고 다시 시작할 수 없습니다. 가상 디스크는 하나의 복제 관계에만 포함될 수 있습니다. 복사 요청에 참여 중인 가상 디스크는 복제된 보조 가상 디스크가 될 수 없습니다. 원격 복제 설정 MD 스토리지 관리자를 사용하여 로컬 및 원격 스토리지 어레이 사이에 원격 복제 설정은 다음으로 구성됩니다.
원격 복제 그룹 원격 복제 프리미엄 기능을 로컬 및 원격 스토리지 어레이에서 성공적으로 활성화한 후에 로컬 스토리지 어레이에서 원격 복제 그룹 을 생성할 수 있습니다. 이 그룹에는 복제된 가상 디스크 쌍이 최소 하나 포함됩니다. 이 중 하나는 로컬 스토리지에, 다른 하나는 원격 스토리지 어레이에 있 습니다. 이 디스크는 두 스토리지 어레이 사이에 일관적인 백업을 제공하기 위해 데이터 동기화 설정을 공유하는 기본 및 보조 디스크 역할을 합니다. 복제된 다중 쌍은 원격 복제 그룹에 상주할 수 있지만 각 쌍은 하나의 원격 복제 그룹의 구성원만 될 수 있습니다. 자세 한 내용은 원격 복제 그룹 요구 사항 및 지침을 참조하십시오. 원격 복제 그룹의 목적 원격 복제 그룹을 생성하면 그룹의 모든 복제 가상 디스크 쌍을 하나로 관리할 수 있습니다. 예를 들어, 그룹의 복제된 모든 가상 디스 크 쌍이 동일한 데이터 동기화 설정, 기본 및 보조 역할, 쓰기 모드를 공유할 수 있습니다.
복제된 쌍은 2개의 가상 디스크로 구성됩니다. 이 중 하나는 로컬 스토리지 어레이의 기본 가상 디스크 역할을 하고 다른 하나는 원격 스토리지 어레이의 보조 가상 디스크 역할을 합니다. 성공적인 원격 복제 구성에서 이 두 가상 디스크에는 모두 같은 데이터의 동일한 복사본이 포함됩니다. 복제된 쌍은 원격 복제 그룹에 포함되어 같은 원격 복제 그룹 안에서 다른 복제된 쌍과 동시에 동기화할 수 있 습니다. I/O 수준에서 모든 쓰기 작업은 기본 가상 디스크에 대해 먼저 수행된 후 보조 가상 디스크에 대해 수행됩니다. 복제된 쌍에서 가상 디스크를 선택하기 위한 가이드라인 복제된 쌍을 생성하는 첫 번째 단계는 로컬 스토리지 어레이의 원격 복제 그룹에 가상 디스크를 추가하여 복제된 쌍을 생성하는 것입 니다. 그러면 이 가상 디스크가 복제된 원격 쌍에서 기본 가상 디스크가 됩니다. 원격 스토리지 어레이의 가상 디스크가 동일한 원격 복제 그룹에 추가되면 복제된 쌍 생성 프로세스가 완료됩니다.
2. Copy Services(복사 서비스) > Remote Replication(원격 복제) > Remote Replication(원격 복제) > Replication Group(복제 그룹) > Complete Replication Pair(복제 쌍 완료)를 선택합니다. Complete Remote Replicated Pair(복제된 원격 쌍 완료) 창이 표시됩니다. 3. 다음 중 하나를 수행합니다. • • Automatic(자동)을 선택하고 표에서 기존 디스크 풀 또는 디스크 그룹을 선택한 후 Finish(마침)를 클릭하여 기본 보조 가상 디스크 선택 및 저장소 설정으로 복제된 쌍 생성 프로세스를 자동으로 완료합니다. Manual(수동)을 선택한 후 Next(다음)를 클릭하여 기존 가상 디스크를 보조 가상 디스크로 선택하고 복제된 원격 쌍의 원격 측면에 대한 저장소 매개 변수를 정의합니다. 복제된 원격 쌍이 생성됩니다. 다음과 같은 상황이 발생합니다.
15 관리 펌웨어 다운로드 주제: • • • • • • • RAID 컨트롤러 및 NVSRAM 패키지 다운로드 RAID 컨트롤러 및 NVSRAM 펌웨어 모두 다운로드 NVSRAM 펌웨어만 다운로드 물리적 디스크 펌웨어 다운로드 MD3060e 시리즈 확장 모듈 EMM 펌웨어 다운로드 자가 모니터링 분석 및 보고 기술(Self-Monitoring Analysis and Reporting Technology; SMART). 미디어 오류 및 판독 불가능한 섹터 RAID 컨트롤러 및 NVSRAM 패키지 다운로드 각 펌웨어 파일에는 버전 번호가 있습니다. 버전 번호는 펌웨어가 주 버전인지, 부 버전인지를 나타냅니다. 엔터프라이즈 관리 창 (EMW)을 사용하여 주 버전의 펌웨어와 부 버전의 펌웨어 모두 다운로드하여 활성화할 수 있습니다. 배열 관리 창(AMW)을 사용하면 부 버전의 펌웨어만 다운로드하여 활성화할 수 있습니다. 노트: 펌웨어 버전은 aa.bb.cc.dd 형식으로 표시됩니다.
5. 펌웨어와 함께 NVSRAM 파일을 다운로드하려는 경우 다음을 수행합니다. a. Transfer NVSRAM file with RAID controller module firmware(RAID 컨트롤러 모듈 펌웨어와 함께 NVSRAM 파일 전송)를 선택합니다. b. Select File(파일 선택)을 클릭합니다. 6. 파일을 활성화하지 않고 RAID 컨트롤러 모듈에 전송하려면, Transfer files but don't activate them (activate later)(파일을 전 송하되 활성화지 않음(나중에 활성화))을 클릭합니다. 7. Transfer(전송)를 클릭합니다. 다음 지침을 숙지합니다. • • Transfer(전송) 단추가 비활성화된 경우, NVSRAM 파일을 선택하거나 Transfer NVSRAM file with RAID controller module firmware(RAID 컨트롤러 모듈 펌웨어와 함께 NVSRAM 파일 전송)를 선택 취소해야 합니다.
NVSRAM 펌웨어만 다운로드 또한, 몇 개의 스토리지 배열에 NVSRAM을 다운로드하고 활성화하기 위해 명령 행 인터페이스(CLI)를 사용할 수 있습니다. NVSRAM 펌웨어만 다운로드하려면 다음을 수행합니다. 1. NVSRAM 펌웨어 다운로드 위치: • • EMW — 7단계로 이동합니다. AMW — 2단계로 이동합니다. 2. AMW에서,Upgrade(업그레이드) > RAID Controller Module NVSRAM(RAID 컨트롤러 모듈 NVSRAM)을 선택하거나 또는 키 Support(지원) 탭을 선택하고 Download Firmware(펌웨어 다운로드)를 클릭합니다. Select download task(다운로드 작업 선 택)에서, Download RAID controller module NVSRAM(RAID 컨트롤러 모듈 NVSRAM 다운로드)을 선택하고 OK(확인)를 클릭 합니다. 오류 메시지가 표시되면 OK(확인)를 클릭하여 닫고 호환 가능한 파일을 선택합니다. 3.
Confirm Download(다운로드 확인) 대화상자가 표시됩니다. 14. Yes(예)를 클릭합니다. 다운로드가 시작되고 Upgrade RAID Controller Module Firmware(RAID 컨트롤러 모듈 펌웨어 업그레이드) 창의 Status(상태) 열에 진행률이 표시됩니다. 물리적 디스크 펌웨어 다운로드 주의: 물리 디스크 펌웨어를 업데이트하는 경우, 데이터 손실을 방지하기 위해 배열에 대한 모든 I/O 활동을 중지해야 합니다. 물리 디스크 펌웨어는 물리 디스크의 다양한 기능을 제어합니다. 디스크 배열 컨트롤러(DAC)는 이 유형의 펌웨어를 사용합니다. 물 리 디스크 펌웨어는 DACstore라고 하는 물리 디스크 영역에 시스템 구성 정보를 저장합니다. DACstore 및 물리 디스크 펌웨어를 통해 물리 디스크를 보다 쉽게 재구성하고 마이그레이션할 수 있습니다. 물리 디스크 펌웨어의 기능은 다음과 같습니다.
주의: 데이터 액세스 유실의 위험성 또는 스토리지 어레이 손상의 위험성 - 확장 인클로저 EMM 펌웨어를 올바르지 않게 다운로 드하면 데이터가 유실되거나 스토리지 어레이가 손상될 수 있습니다. 기술 지원 담당자의 안내에 따라서만 다운로드를 수행하십 시오. 주의: 확장 인클로저 EMM 사용 불가능의 위험성 - 확장 인클로저 EMM 펌웨어를 다운로드하는 동안에는 스토리지 어레이의 구 성을 변경하지 마십시오. 구성을 변경하면 펌웨어 다운로드에 실패하고 선택한 확장 인클로저가 사용 불가능하게 됩니다. 1. AMW에서 Upgrade(업그레이드) > EMM Firmware(EMM 펌웨어)를 선택합니다. Download Environmental (EMM) Card Firmware(환경 (EMM) 카드 펌웨어 다운로드) 대화상자가 표시됩니다. 2.
16 펌웨어 인벤토리 스토리지 배열은 RAID 컨트롤러 모듈, 물리 디스크 및 인클로저 관리 모듈(EMM)을 비롯한 많은 구성요소로 이루어져 있습니다. 이러 한 각 구성요소에는 펌웨어가 포함되어 있습니다. 일부 버전의 펌웨어는 다른 버전의 펌웨어에 종속됩니다. 스토리지 배열에 있는 모 든 펌웨어 버전에 대한 정보를 캡처하려면 펌웨어 인벤토리를 확인합니다. 펌웨어 인벤토리에 특정 스토리지 배열에 대한 정보가 포함되어 있지 않은 경우, 해당 스토리지 배열에서 펌웨어 인벤토리 서비스를 사용할 수 없습니다. 펌웨어 인벤토리를 텍스트 파일에 저장할 수도 있습니다. 그런 다음 이 파일을 기술 지원 담당자에게 분석을 위해 보낼 수 있습니다. 기술 지원 담당자가 펌웨어 불일치를 검색할 수 있습니다. 주제: 펌웨어 인벤토리 보기 • 펌웨어 인벤토리 보기 1. 다음 작업 중 하나를 수행하여 단일 스토리지 배열 또는 모든 스토리지 배열에 대한 펌웨어 정보를 확인합니다.
17 시스템 인터페이스 주제: • • 가상 디스크 서비스 볼륨 섀도 복사본 서비스 가상 디스크 서비스 Microsoft VDS(Virtual Disk Service)는 Windows 운영 체제의 구성 요소입니다. VDS 구성 요소는 제공자라고 하는 타사 공급업체별 소 프트웨어 모듈을 사용하여, MD 시리즈 스토리지 어레이 등과 같은 타사 스토리지 리소스에 액세스하여 구성합니다. VDS 구성 요소 는 디스크 및 기타 스토리지 하드웨어를 관리할 수 있는 단일 인터페이스를 제공하는 API(애플리케이션 프로그래밍 인터페이스) 세 트를 제공합니다. MD 시리즈 VDS Provider를 사용하면 디스크 관리자를 비롯한 Windows 툴을 통해 스토리지 어레이 가상 디스크에 액세스하여 구성할 수 있습니다. MD 시리즈 스토리지 어레이용 VDS Provider는 MD 시리즈 리소스 DVD에서 볼 수 있습니다. VDS에 대한 자세한 정보는 Microsoft.com을 참조하십시오.
• • MD 스토리지 관리자에 생성된 스냅샷 가상 디스크는 차등 스냅샷입니다. Plex 스냅샷은 지원되지 않습니다. VSS 스냅샷의 원본 가상 디스크로 사용될 가상 디스크의 이름은 16자를 넘지 않아야 합니다. VSS 하드웨어 제공자는 기본 가상 디스크 이름을 스냅샷 및 저장소 가상 디스크 이름의 접두사로 사용합니다. 원본 가상 디스크 이름이 16자를 초과하면 결과로 나 타나는 스냅샷 및 저장소 이름이 너무 길어집니다. 노트: 볼륨은 가상 디스크의 다른 명칭입니다. VDS 및 VSS에 대한 자세한 정보는 Microsoft.com을 참조하십시오.
18 스토리지 어레이 소프트웨어 주제: • • • • • • • • • • • • • • • • 시작 루틴 디바이스 상태 조건 추적 버퍼 물리적 디스크 데이터 취합 이벤트 로그 복구 안내 스토리지 어레이 프로파일 실제 연결 보기 응답하지 않는 스토리지 어레이 상태에서 복구 물리적 디스크 찾기 확장 엔클로저 찾기 상태 정보 캡처 SMrepassist 유틸리티 식별되지 않은 디바이스 식별되지 않은 스토리지 어레이 복구 호스트 컨텍스트 에이전트 소프트웨어 시작 또는 다시 재시작 시작 루틴 어레이의 시작 루틴이 진행되는 동안 아래 표에 설명된 사항을 육안으로 검사하고 직접 들어보십시오. 전면 패널과 후면 패널 표시등 에 대한 설명은 스토리지 배열 정보를 참조하십시오. 보기/듣기 내용: 조치 경보 메시지 스토리지 관리 설명서를 참조하십시오. 물리 디스크에 액세 도움말 얻기를 참조하십시오.
표 18. 상태 아이콘 및 설명 상태 아이콘 설명 Optimal(최적) 관리형 스토리지 배열에서 각 구성요소가 올바른 작동 조건에 있습니다. Needs Attention(주의 필 요) 관리형 스토리지 배열에 사용자 개입이 필요한 문제가 있습니다. Unresponsive(무응답) 스토리지 관리 스테이션이 스토리지 배열 또는 스토리지 배열에 있는 하나 의 RAID 컨트롤러 모듈 또는 두 RAID 컨트롤러 모듈과 통신할 수 없습니다. Fixing Status(수정 상태) Needs Attention(주의 사항) 상태가 정정되었고 관리형 스토리지 어레이가 Optimal(최적) 상태로 전환 중입니다. Unsupported(지원되지 않 음) 해당 노드가 이 버전의 MD Storage Manager에서 지원되지 않습니다. Software Unsupported(지 원되지 않는 소프트웨어) 스토리지 배열이 더 이상 MD 스토리지 관리자에서 지원되지 않는 소프트 웨어 레벨을 실행 중입니다.
표 19. 추가 상태 아이콘 및 설명 (계속) 상태 아이콘 설명 서 알림을 설정하고 인밴드(In-Band) 스토 리지 어레이 하위 노드의 상태가 Needs Upgrade(업그레이드 필요)일 경우, 트리 보기의 상위 노드 옆에 Alert Disables(알 림 비활성화) 상태 아이콘이 표시됩니다. Adding a Storage Array(스토리지 배열 추 가) Contacting Storage Array(스토리지 어 레이 연결) 아이콘이 각각의 관리형 스토 리지 어레이의 상태가 확인될 때까지 트리 보기와 표 보기에 나타납니다. Contacting Storage Array(스토리지 어 레이 연결) 아이콘이 EMW Status Bar(EMW 상태 표시줄)과 AMW Status Bar(AMW 상태 표시줄)에 나타나며 툴 설 명에 Contacting Storage arrays(스토리지 어레이 연결)가 표시됩니다. 각 스토리지 어레이에 연결되면, 해당 상 태가 확보되어 트리 보기와 표 보기에 표 시됩니다.
• 각 RAID 컨트롤러 모듈에 대한 수집 상태가 Failed(실패)일 경우, 장애의 원인이 표시되며 장애가 발생한 RAID 컨트롤러 모듈의 트 레이스 파일이 없습니다. 추적 버퍼 검색 트레이스 버퍼를 검색하려면 다음을 수행합니다. 1. AMW에서 Monitor(모니터) > Health(상태) > Retrieve Trace Buffers(트레이스 버퍼 검색)를 선택합니다. Retrieve Trace Buffers(트레이스 버퍼 검색) 대화상자가 표시됩니다. 2. RAID 컨트롤러 모듈 0, RAID 컨트롤러 모듈 1 또는 둘 다 선택합니다. 확인란 오른쪽에 있는 RAID 컨트롤러 모듈 상태 메시지가 RAID 컨트롤러 모듈이 오프라인 상태임을 나타내면, 확인란이 비활성 화됩니다. 3. Trace buffers(트레이스 버퍼) 목록에서, 관련 옵션을 선택합니다. 4.
4. 원하는 설정을 선택하고 OK(확인)를 클릭합니다. Schedule Support Data Collection(지원 데이터 수집 일정 설정) 대화상자가 표시됩니다. Storage arrays(스토리지 어레이) 표 가 일정 변경사항으로 업데이트됩니다. 5. 수집된 지원 데이터 파일을 저장할 위치를 선택합니다. • • 기본 위치를 사용하려면 Use default location(기본 위치 사용)을 선택합니다. 다른 위치를 선택하려면 Use alternate location(대체 위치 사용)을 선택한 다음 Browse(찾아보기) 단추를 클릭하여 원하는 디렉터리를 선택합니다. 노트: 파일 이름은 수정할 수 없습니다. 6. 확인을 클릭합니다. 지원 데이터 취합 일정 일시 중지 또는 재개 지원 데이터 수집 일정 일시 중지 기능은 예정된 작업을 일시적으로 비활성화합니다. 지원 데이터 수집 일정을 일시 중지하면, 일정의 타이머는 계속 진행되지만 예정된 지원 데이터 수집은 발생하지 않습니다.
이벤트 로그 보기 노트: 이 옵션은 기술 지원 담당자의 안내에 따라서만 사용하십시오. 이벤트 로그를 보려면 다음을 수행합니다. 1. AMW에서 Monitor(모니터) > Reports(보고서) > Event Log(이벤트 로그)를 선택합니다. 이벤트 로그가 표시됩니다. 기본적으로 요약 뷰가 표시됩니다. 2. 선택한 각 로그 항목의 세부사항을 보려면 View details(세부사항 보기)를 선택합니다. 로그 항목에 대한 자세한 정보가 포함된 Detail(세부사항) 창이 이벤트 로그에 추가됩니다. 한 번에 하나의 로그 항목에 대한 세부 사항을 볼 수 있습니다. 3. 이벤트 로그를 저장하려면 Save As(다른 이름으로 저장)를 클릭합니다. Save Events(이벤트 저장) 대화상자가 표시됩니다. 관련 폴더를 탐색하고 관련된 파일 이름을 입력하고 Save(저장)를 클릭합니 다. 4. 이벤트 로그에서 모든 로그 항목을 지우려면 Clear All(모두 지우기)을 클릭합니다. 5.
조건이 현재 탭에 있는 경우, 해당 조건이 스토리지 배열 프로파일 정보에서 강조 표시됩니다. 노트: 검색은 현재 탭으로만 제한됩니다. 다른 탭에서 조건을 검색하려면 탭을 선택하고 Find(찾기) 단추를 다시 클릭합 니다. c. 조건의 추가적인 발생 항목을 검색하려면 Find(찾기) 단추를 다시 클릭합니다. 5. 스토리지 배열 프로파일을 저장하려면 다음 단계를 수행합니다. a. Save As(다른 이름으로 저장)를 클릭합니다. b. 스토리지 배열 프로파일의 모든 섹션을 저장하려면 All sections(모든 섹션)를 선택합니다. c. 스토리지 배열 프로파일의 특정 섹션에 있는 정보를 저장하려면, Select sections(섹션 선택)를 선택하고 저장할 섹션에 해당 되는 확인란을 선택합니다. d. 적절한 디렉터리를 선택합니다. e. File Name(파일 이름)에서, 선택한 항목의 파일 이름을 입력합니다. 파일을 여는 특정 소프트웨어 응용프로그램과 파일을 연 관시키려면 파일 확장명(예: .
10. 적절한 네트워크 구성 작업을 수행했는지 확인합니다. 예를 들어, 각 RAID 컨트롤러 모듈에 IP 주소를 할당했는지 확인합니다. 11. 케이블 또는 네트워크 접근성에 문제가 있으면 20단계를 참조하고, 그렇지 않으면 12단계를 참조하십시오. 12. 인밴드(In-Band) 관리형 스토리지 어레이의 경우, 호스트 연결 가능성을 할 수 있도록 ping 명령을 사용하여 네트워크를 통해 호 스트에 액세스하도록 합니다. 다음 명령 중 하나를 입력하고 키를 누릅니다. 13. 14. 15. 16. 17. 18. • ping • ping 확인에 성공하면 14단계를 참조하고, 그렇지 않으면 15단계를 참조하십시오. EMW에서 Unresponsive(무응답) 상태의 호스트를 제거하고 Add Storage Array(스토리지 배열 추가)를 선택하여 호스트를 다시 추가합니다.
• • 흰색 LED가 있는 확장 인클로저를 사용하는 경우, Blink Expansion Enclosure(확장 인클로저 깜박임) 작업을 수행하면 확장 인클로 저의 흰색 LED가 켜지며 LED는 깜박이지 않습니다. 다른 유형의 확장 인클로저를 사용하는 경우, 이 작업을 수행하면 확장 인클로저에 있는 모든 물리 디스크의 해당 LED가 깜박거 립니다. 확장 인클로저를 찾으려면 다음을 수행합니다. 1. Hardware(하드웨어) 탭을 선택합니다. 2. 검색할 확장 인클로저에서 물리 디스크를 선택합니다. 3. Hardware(하드웨어) > Blink(깜박임) > Expansion Enclosure(확장 인클로저)를 선택합니다. 확장 인클로저 또는 물리 디스크에 있는 LED가 켜집니다. 4. 확장 인클로저를 찾았으면 OK(확인)를 클릭합니다. LED 깜박임이 중지됩니다(확장 인클로저에 파란색 LED가 있는 경우, 파란색 LED가 꺼짐).
노트: Windows에서 장착 지점 경로는 물리 디스크 문자입니다. 유틸리티에서 다음을 구분할 수 없으면 명령줄에 오류 메시지가 표시됩니다. • • 소스 가상 디스크와 스냅샷 가상 디스크(예: 스냅샷 가상 디스크가 제거된 경우). 표준 가상 디스크와 가상 디스크 복사본(예: 가상 디스크 복사가 제거된 경우). 식별되지 않은 디바이스 MD 스토리지 관리자가 새 스토리지 배열에 액세스할 수 없는 경우 식별되지 않은 노드 또는 장치 오류가 발생합니다. 이 오류의 원인 으로는 네트워크 연결 문제, 스토리지 배열 꺼짐 또는 스토리지 배열 없음 등이 있습니다. 노트: 복구 절차를 시작하기 전에, 호스트 컨텍스트 에이전트 소프트웨어가 설치되어 작동되고 있는지 확인합니다. 호스트가 스 토리지 배열에 연결되기 전에 호스트를 시작하면 호스트 컨텍스트 에이전트 소프트웨어가 스토리지 배열을 찾을 수 없습니다. 이 경우, 연결이 제대로 설정되어 있는지 확인하고 호스트 컨텍스트 에이전트 소프트웨어를 다시 시작하십시오.
여전히 문제가 있을 경우 도움말 얻기를 참조하십시오. 6. 하나 이상의 컨트롤러에 대한 네트워크 트래픽이 너무 많은지 확인합니다. 이 경우, MD 스토리지 관리자는 스토리지 배열에 있는 컨트롤러와의 통신을 정기적으로 재설정하려고 시도하므로 문제가 자동으로 해결됩니다. 스토리지 배열이 무응답 상태이고 이후 에 스토리지 배열과의 연결 시도에 성공할 경우 스토리지 배열이 응답 상태가 됩니다. 7. 대역외 스토리지 배열의 경우, 스토리지 배열에 다른 스토리지 관리 스테이션에서의 관리 작업이 수행되고 있는지 확인합니다. 수행되고 있는 관리 작업의 유형 및 이와 함께 수행되는 관리 세션의 수에 따라 컨트롤러에 대한 TCP/IP 연결 수가 설정됩니다. 최대 TCP/IP 연결 수가 설정되면 컨트롤러 응답이 중지됩니다. 이 경우, 일부 TCP/IP 연결이 완료되면 컨트롤러가 다른 연결 시도 에 대해 응답 상태가 되므로 문제가 자동으로 해결됩니다. 8.
19 도움말 보기 주제: Dell EMC에 문의하기 • Dell EMC에 문의하기 노트: 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에서 연락처 정보를 찾 을 수 있습니다. Dell은 다양한 온라인/전화 기반의 지원 및 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell에 문의하려면 1. 2. 3. 4. Dell.com/support로 이동합니다. 지원 카테고리를 선택합니다. 페이지 맨 아래에 있는 Choose a Country/Region(국가/지역 선택) 드롭다운 메뉴에서 국가 또는 지역을 확인합니다. 필요한 서비스 또는 지원 링크를 선택하십시오.