Dell EMC PowerVault MD 34XX/38XX-ReiheSpeicher-Arrays Administratorhandbuch September 2018 Rev.
Hinweise, Vorsichtshinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, mit denen Sie Ihr Produkt besser einsetzen können. VORSICHT: Ein VORSICHTSHINWEIS warnt vor möglichen Beschädigungen der Hardware oder vor Datenverlust und zeigt, wie diese vermieden werden können. WARNUNG: Mit WARNUNG wird auf eine potenziell gefährliche Situation hingewiesen, die zu Sachschäden, Verletzungen oder zum Tod führen kann. © 2012 - 2018 Dell Inc. oder Ihre Tochtergesellschaften.
Inhaltsverzeichnis Kapitel 1: Einführung......................................................................................................................12 Dell EMC PowerVault Modular Disk Storage Manager................................................................................................... 12 Benutzeroberfläche..............................................................................................................................................................
Host-Typen.....................................................................................................................................................................24 Erweiterte Funktionen........................................................................................................................................................ 25 Typen unterstützter Snapshot-Funktionen...............................................................................................................
Ändern der iSCSI-Ziel-Authentifizierung.......................................................................................................................... 48 Eingeben gegenseitiger Authentifizierungberechtigungen............................................................................................ 49 Einrichten von CHAP-Geheimschlüsseln..........................................................................................................................
Status schlanker virtueller Laufwerke.........................................................................................................................70 Vergleich – Typen von virtuellen Laufwerken und Kopierdienste........................................................................... 70 Rollback der schlanken virtuellen Laufwerke............................................................................................................. 70 Initialisieren eines schlanken virtuellen Laufwerks....
Automatisches Verwalten des nicht konfigurierten Speicherplatzes in Laufwerkspools........................................... 97 Lokalisieren physikalischer Laufwerke in einem Laufwerkspool.................................................................................... 98 Umbenennen eines Laufwerkspools................................................................................................................................. 98 Konfigurieren von Warnbenachrichtigungen für einen Laufwerkspool.......
Einschränkungen für ein Snapshot-Rollback............................................................................................................. 117 Starten eines Snapshot-Rollbacks..............................................................................................................................118 Wiederaufnehmen eines Snapshot-Abbild-Rollbacks...............................................................................................118 Abbrechen eines Snapshot-Abbild-Rollbacks........
Lese-/Schreibberechtigungen des virtuellen Laufwerks.............................................................................................. 146 Einschränkungen bei virtuellen Laufwerkskopien.......................................................................................................... 146 Erstellen einer virtuellen Laufwerkskopie........................................................................................................................
Replizierte Remote-Paare und Replikations-Repositorys............................................................................................. 162 Typen der Remote-Replikation.........................................................................................................................................163 Unterschiede zwischen Remote-Replikationsfunktionen.......................................................................................
Anzeigen der physikalischen Zuweisungen.....................................................................................................................185 Wiederherstellen eines nicht reagierenden Speicher-Arrays........................................................................................185 Lokalisieren eines physikalischen Laufwerks.................................................................................................................. 186 Lokalisieren eines Erweiterungsgehäuses..
1 Einführung VORSICHT: Bevor Sie die in diesem Dokument aufgeführten Vorgehensweisen durchführen, sollten Sie die wichtigen Sicherheitsinformationen im Dokument „Informationen zu Sicherheit, Umweltschutz und Vorschriften“ lesen.
ANMERKUNG: Die Symbolleiste ist nur im EMW verfügbar. • • Die Registerkarten unter der Symbolleiste – Mit den Registerkarten werden die Aufgaben, die Sie auf einem Speicher-Array ausführen können, in Gruppen unterteilt. Die Statusleiste unter den Registerkarten – Die Statusleiste zeigt Statusmitteilungen und -symbole im Zusammenhang mit dem Speicher-Array an. ANMERKUNG: Standardmäßig werden die Symbolleiste und die Statusleiste nicht angezeigt.
Array-Management-Fenster (AMW) Sie können das AMW ausgehend vom EMW öffnen. Das AMW bietet Verwaltungsfunktionen für ein einzelnes Speicher-Array. Es können mehrere AMWs gleichzeitig geöffnet sein, um unterschiedliche Speicher-Arrays zu verwalten. Im AMW können Sie: • • • • • • • • • Speicher-Array-Optionen auswählen – Zum Beispiel ein Speicher-Array umbenennen, ein Kennwort ändern oder eine Mediensuche im Hintergrund aktivieren.
Dell EMC PowerVault Modular Disk Configuration Utility ANMERKUNG: Dell EMC PowerVault Modular Disk Configuration Utility (MDCU) wird nur auf MD-Series-SpeicherArrays unterstützt, die das iSCSI-Protokoll verwenden. MDCU ist ein iSCSI-Konfigurationsassistent, der in Verbindung mit dem MD Storage Manager die Konfiguration von iSCSI-Verbindungen vereinfacht. Die MDSM-Software befindet sich auf dem MD Series Ressourcen-Datenträger.
2 Informationen zum MD Series-Speicher-Array In diesem Kapitel werden die Speicher-Array-Konzepte erläutert, die für die Konfiguration und den Betrieb von Dell MD Series-SpeicherArrays hilfreich sind.
Status physikalischer Festplatten Die folgende Tabelle beschreibt die verschiedenen Zustände der physikalischen Laufwerke, die vom Speicher-Array erkannt und im MD Storage Manager unter der Registerkarte „Hardware“ (Hardware) oder im Speicher-Array -Profil auf der Registerkarte Summary (Zusammenfassung) gemeldet werden. Tabelle 1.
Tabelle 2. Zustände virtueller RAID-Controller-Laufwerke Zustand Beschreibung Optimal Das virtuelle Laufwerk enthält physikalische Laufwerke, die online sind. Herabgesetzt Das virtuelle Laufwerk mit einem redundanten RAID-Level enthält ein physikalisches Laufwerk, auf das nicht zugegriffen werden kann. Das System kann zwar immer noch ordnungsgemäß funktionieren, die Leistung ist jedoch möglicherweise beeinträchtigt und weitere Laufwerksausfälle könnten zu einem Datenverlust führen.
Einschränkungen für die maximale Anzahl unterstützter physikalischer Laufwerke Obwohl die mit Erweiterungsfunktions-Kit gelieferten PowerVault MD Series-Speicher-Arrays bis zu 180 physikalische Laufwerke unterstützen können, werden RAID 0- und RAID 10-Konfigurationen mit mehr als 120 physikalischen Laufwerken nicht unterstützt. MD Storage Manager erzwingt beim Einstellen einer RAID 0- oder RAID 10-Konfiguration keine Beschränkung auf 120 physikalische Laufwerke.
RAID-10 VORSICHT: Versuchen Sie nicht, virtuelle Laufwerksgruppen zu erstellen, die die Beschränkung auf 120 physikalischen Laufwerken in einer RAID 10-Konfiguration überschreiten, selbst wenn die Erweiterungsfunktion auf Ihrem SpeicherArray aktiviert ist. Die Überschreitung der maximalen Anzahl von 120 physikalischen Laufwerken kann zur Instabilität des Speicher-Arrays führen. RAID 10 ist eine Kombination aus RAID 0 und RAID 1 und verwendet Laufwerk-Striping auf replizierten Laufwerken.
Medienprüfung Eine weitere vom Speicher-Array durchgeführte Hintergrundaufgabe ist die Medienprüfung aller konfigurierten physikalischen Laufwerke in einer Laufwerksgruppe. Das Speicher-Array nutzt den Lesevorgang für die Überprüfung auf dem in virtuellen Laufwerken konfigurierten Speicherplatz und dem für die Metadaten reservierten Speicherplatz. Zykluszeit Der Arbeitsgang Medienprüfung läuft nur auf ausgewählten Laufwerksgruppen, unabhängig von anderen Laufwerksgruppen.
• • Wenn die E/A-Aktivität die Segmentgröße übersteigt, können Sie diese erhöhen, um die Anzahl der für eine einzelne E/A erforderlichen Laufwerke zu reduzieren. Durch die Verwendung eines einzelnen physikalischen Laufwerks für eine einzelne Anforderung werden Laufwerke für andere Anforderungen frei, besonders wenn mehrere Benutzer auf eine Datenbank oder eine Speicherumgebung zugreifen. Wenn Sie das virtuelle Laufwerk in einer Einzelbenutzerumgebung mit einem hohen Aufkommen an E/A verwenden (z.B.
• • • • • Kapazitätserweiterung von virtuellen Laufwerken RAID-Level-Migration Segmentgrößen-Migration Erweiterung einer virtuellen Laufwerksgruppe Defragmentierung einer Laufwerksgruppe Die Priorität jedes dieser Vorgänge kann geändert werden, um den Leistungsanforderungen der Umgebung, in der die Vorgänge auszuführen sind, zu entsprechen. ANMERKUNG: Das Einstellen einer hohen Prioritätsstufe hat Auswirkungen auf die Leistung des Speicher-Arrays.
• • • Laufwerks warten, bis die eingesetzten physikalischen Laufwerke im MD Storage Manager angezeigt werden oder 30 Sekunden verstrichen sind (je nachdem, was zuerst eintritt). ANMERKUNG: Ohne die Wartezeit zwischen den Einsetzvorgängen kann das Speicher-Array instabil und zeitweise nicht mehr verwaltet werden.
Erweiterte Funktionen Das RAID-Gehäuse unterstützt mehrere erweiterte Funktionen: • • Virtuelle Snapshot-Laufwerke Virtuelle Laufwerkskopie ANMERKUNG: Die oben aufgeführten Premium-Funktionen müssen separat aktiviert werden. Wenn Sie diese Funktionen erworben haben, wird eine Aktivierungskarte geliefert, die Anweisungen für die Aktivierung dieser Funktionalität enthält.
Daten auf dem Ziel überschrieben. Als virtuelles Ziellaufwerk kann ein virtuelles Standardlaufwerk oder das virtuelle Quelllaufwerk eines ausgefallenen oder deaktivierten virtuellen Snapshot-Laufwerks verwendet werden. ANMERKUNG: Die Kapazität des virtuellen Ziellaufwerks muss gleich groß oder größer als die Kapazität des virtuellen Quelllaufwerks sein. Wenn Sie den Laufwerkskopiervorgang starten, müssen Sie die Rate, mit der die Kopie abgeschlossen wird, festlegen.
Besitzer können auch zu einem späteren Zeitpunkt noch geändert werden, um die Arbeitsbelastung nach der tatsächlichen Verwendung auszugleichen. Wenn der Besitz des virtuellen Laufwerks nicht manuell ausgeglichen wird, ist es möglich, dass ein Controller den Großteil der Arbeit zu erledigen hat, während der andere Controller inaktiv ist. Beschränken Sie die Anzahl der virtuellen Laufwerke in einer Laufwerksgruppe.
Tabelle 3. Eigenschaften der verschiedenen Arten der Leistungsüberwachung Leistungsüberwac hungstyp Abfrageintervall Dauer der Anzeige Maximale Anzahl der angezeigten Objekte Fähigkeit zum Speichern von Daten Starten und Anhalten der Überwachung Echtzeit als Grafik 5 Sekunden 5-MinutenGleitfenster 5 Nein Startet automatisch, wenn AMW-Fenster geöffnet wird. Hält automatisch an, wenn AMW-Fenster geschlossen wird.
Tabelle 4. Bedeutung von Leistungsdaten (fortgesetzt) Leistungsdaten Bedeutung für die Leistungsanpassung Möglicherweise stellen Sie eine Disparität bei der Gesamt-E/AArbeitslast der RAID-Controller-Module fest. So ist beispielsweise die Arbeitslast eines RAID-Controller-Moduls sehr hoch oder steigt mit der Zeit, während die eines anderen geringer oder stabiler ist.
Tabelle 4. Bedeutung von Leistungsdaten (fortgesetzt) Leistungsdaten Bedeutung für die Leistungsanpassung Informationen zum Lese/Schreib-Cache und zur Leistung finden Sie in der Liste der verwandten Themen am Ende dieses Themas.
Tabelle 4. Bedeutung von Leistungsdaten (fortgesetzt) Leistungsdaten Bedeutung für die Leistungsanpassung der Cache-Treffer-Prozentsatz für eine sequenzielle E/AArbeitslast erhöht werden. Anzeigen von grafischen Echtzeitdaten des Leistungsmonitors Sie können grafische Echtzeit-Leistungsdaten als einzelnes Diagramm oder als Dashboard mit sechs Diagrammen auf einem Bildschirm anzeigen. Ein Echtzeit-Leistungsmonitor-Diagramm zeichnet während der Zeit eine einzige Leistungsmetrik für bis zu fünf Objekte.
Das Dashboard auf der Registerkarte „Leistung“ wird mit dem neuen Portlet aktualisiert. 6. Um das Dialogfeld zu schließen, klicken Sie auf Abbrechen. Festlegen von Leistungskennzahlen Sie können die folgenden Leistungsdaten erfassen: • • Gesamt-E/A-Vorgänge – Gesamt-E/A-Vorgänge, die seit Beginn der Abrufsitzung von diesem Objekt durchgeführt wurden.
• • Klicken Sie auf die Registerkarte Leistung, und klicken Sie dann auf den Link Echtzeit-Text-Leistungsmonitor starten. Wählen Sie Überwachung > Funktionszustand > Leistung überwachen > Echtzeit-Leistungsmonitor > Text anzeigen aus. Das Dialogfeld Echtzeit-Text-Leistungsmonitor anzeigen wird angezeigt. 2. Um Objekte für die Überwachung und das Abfrageintervall auszuwählen, klicken Sie auf die Schaltfläche Einstellungen.
10. Wählen Sie einen Speicherort aus, geben Sie einen Dateinamen ein, und klicken Sie dann auf Speichern. Sie können die Datei entweder als Textdatei mit der Standarderweiterung .perf speichern, die Sie mit einem Texteditor öffnen können, oder als Datei mit kommagetrennten Werten mit der Standarderweiterung .csv, die Sie mit einer beliebigen Tabellenkalkulationsanwendung öffnen können. 11. Um das Dialogfeld zu schließen, klicken Sie auf Abbrechen. Starten und Anhalten des Hintergrund-Leistungsmonitors 1.
Metrikwert in Tausend (K), beginnend mit 100 K, angezeigt, bis die Anzahl 9999 K erreicht. Anschließend wird der Wert in Millionen (M) angezeigt. Für Mengen, die größer als 9999 K, jedoch kleiner als 100 M sind, wird der Wert in Zehntel (z. B. 12,3 M) angezeigt. 1. Klicken Sie im Array-Management-Fenster (AMW) auf die Registerkarte Leistung. 2. Klicken Sie auf den Link Hintergrund-Leistungsmonitor starten.
Sie können immer nur eine Metrik gleichzeitig auswählen. 6. Wählen Sie in der Liste Objekt(e) auswählen die Objekte aus, für die Sie Hintergrund-Leistungsdaten anzeigen möchten. Sie können bis zu fünf Objekte zur Überwachung in einem einzigen Diagramm auswählen. Verwenden Sie „STRG + Klick“ bzw. „Umschalttaste + Klick“, um mehrere Objekte auszuwählen. Jedes Objekt wird als separate Linie im Diagramm angezeigt. Das Diagramm zeigt alle Datenpunkte der gespeicherten Datei.
3 Erkennen und Verwalten des Speicher-Arrays Ein Speicher-Array lässt sich auf zwei Weisen verwalten: • • Bandexterne Verwaltung Bandinterne Verwaltung Das Enterprise Management Window (EMW) ist die erste Seite, die beim Öffnen des Modular Disk Storage Manager (MDSM) geladen wird, und ermöglicht Ihnen die Ermittlung, Verbindung und Verwaltung von MD3-Speicherarrays über bandinterne und bandexterne Konnektivität. Die Speichernamen sind Arrays, die ermittelt wurden.
ANMERKUNG: Manche Betriebssysteme können nur als Speicherverwaltungsstationen verwendet werden. Beziehen Sie sich für weitere Informationen zum von Ihnen verwendeten Betriebssystem siehe MD PowerVault Support-Matrix unter Dell.com/support/manuals. Virtuelles Zugriffslaufwerk Jedes RAID-Controller-Modul in einem MD Series -Speicher-Array hält ein bestimmtes virtuelles Laufwerk vor, das als virtuelles Zugriffslaufwerk bezeichnet wird.
• • Out-of-band management (Bandexterne Verwaltung) – Geben Sie den DNS/Netzwerk-Namen, eine IPv4-Adresse oder eine IPv6-Adresse für das RAID Controller Module (RAID-Controller-Modul) im Speicher-Array ein. In-band management (Bandinterne Verwaltung) – Geben Sie einen Namen oder einen DNS/Netzwerk-Namen, eine IPv4Adresse oder eine IPv6-Adresse für den Host (Host) ein, durch welche das Specher-Array mit dem Netzwerk verbunden ist.
Die LED-Anzeigen der physikalischen Laufwerke im Speicher-Array blinken. 2. Nachdem das Speicher-Array gefunden wurde, klicken Sie auf OK. Das Aufblinken der LEDs wird gestoppt. 3. Wenn das Aufblinken der LED-Anzeigen nicht endet, wählen Sie Hardware (Hardware) > Blink (Blinken) > Stop All Indications (Alle Anzeigen stoppen) aus. Benennen oder Umbenennen von Speicher-Arrays Sie können einem Speicher-Array einen Namen geben, es umbenennen und mit Kommentaren versehen, um seine Identifikation zu erleichtern.
Richtlinien für Kennwörter • • • Verwenden Sie für das Speicher-Array sichere Kennwörter. Ein Kennwort sollte für Sie leicht zu merken sein, aber schwer für andere herauszufinden. Verwenden Sie beispielsweise Ziffern oder Sonderzeichen anstelle von Buchstaben, etwa 1 für den Buchstaben I oder das Zeichen @ für den Buchstaben a. Um erhöhten Schutz zu gewährleisten, benötigen Sie ein langes Kennwort mit mindestens 15 alphanumerischen Zeichen. Die maximale Länge für Kennwörter beträgt 30 Zeichen.
Das Dialogfeld Aktivierung erweiterter Funktionen bestätigen wird angezeigt. 4. Klicken Sie auf Ja. Die erforderliche Erweiterungsfunktion wird auf Ihrem Speicher-Array aktiviert. 5. Klicken Sie auf Schließen. Anzeigen der Failover-Benachrichtigung Die Failover-Benachrichtigungsverzögerung für ein Speicher-Array ist einstellbar.
3. Klicken Sie auf OK. 4. Wenn ein Kennwort für das entsprechende Speicher-Array festgelegt wurde, wird das Dialogfeld Kennwort eingeben angezeigt. Geben Sie das aktuelle Kennwort für das Speicher-Array ein. 5. Klicken Sie auf OK. Konfigurieren von Warnbenachrichtigungen MD Storage Manager kann Alarme senden für jeden Zustand im Speicherarray, der einen Eingriff erfordert.
4. Wählen Sie die Registerkarte E-Mail, um die E-Mail-Benachrichtigungsziele zu konfigurieren. • • • • Hinzufügen einer E-Mail-Adresse—Geben Sie im Bereich E-Mail-Adresse die E-Mail-Adresse ein und klicken Sie auf Hinzufügen. Ersetzen einer E-Mail-Adresse—Wählen Sie im Bereich Konfigurierte E-Mail-Adressen die zu ersetzende E-Mail-Adresse aus, geben Sie unter E-Mail-Adresse die Ersatz-E-Mail-Adresse ein und klicken Sie auf Ersetzen.
3. Informationen zum Konfigurieren einer SNMP-Warnung von der Ereignisüberwachung finden Sie unter Erstellen von SNMPWarnbenachrichtigungen von der Ereignisüberwachung. 4. Informationen zum Konfigurieren einer SNMP-Warnung vom Speicher-Array finden Sie unter Erstellen von SNMPWarnbenachrichtigungen vom Speicher-Array.
Dienst ausgeführt wird. Das Trap-Ziel muss mindestens die Netzwerkverwaltungsstation sein. Berücksichtigen Sie die folgenden Richtlinien, wenn Sie SNMP-Warnbenachrichtigungen konfigurieren: • • Host-Ziele für SNMP-Traps müssen einen SNMP-Dienst ausführen, damit die Trap-Informationen verarbeitet werden können. Globale Einstellungen sind für die SNMP-Trap-Nachrichten nicht erforderlich.
Nach dem Installieren eines neuen Akkumoduls startet automatisch ein Lernzyklus. Die Lernzyklen für die Akkus in beiden RAID-ControllerModulen in Duplexsystemen finden gleichzeitig statt. Lernzyklen laufen automatisch in regelmäßigen Zeitabständen jeweils zur selben Zeit und am selben Wochentag ab. Der Zeitabstand zwischen den einzelnen Zyklen wird in Wochen angegeben. Verwenden Sie zum Festlegen des Zeitabstands die folgenden Richtlinien: • • • • Sie können den Standardzeitabstand verwenden.
4 Verwenden von iSCSI ANMERKUNG: Die folgenden Abschnitte werden nur auf MD-xx0i-Speicher-Arrays unterstützt, die iSCSI-Protokoll verwenden.
Eingeben gegenseitiger Authentifizierungberechtigungen Die gegenseitige Authentifizierung – auch als Zwei-Wege-Authentifizierung bezeichnet – ermöglicht einem Client bzw. Benutzer, sich gegenüber einem Host-System auszuweisen, während das Host-System sich zugleich gegenüber dem Benutzer authentifiziert. Die Authentifizierung wird so durchgeführt, dass jede Seite Sicherheit über die Identität der jeweils anderen Seite erhält. So fügen Sie gegenseitige Authentifizierungsberechtigungen hinzu: 1.
Tabelle 6. Zulässige Zeichen zur Verwendung in CHAP-Geheimschlüsseln (fortgesetzt) Zulässige Zeichen zur Verwendung in CHAP-Geheimschlüsseln \ ] ^ _ a b c d e f g h I j k l m n o P q r s t u v W x y z { | } ~ Ändern der iSCSI-Zielidentifikation Der Name des iSCSI-Ziels kann nicht geändert werden. Sie können ihn jedoch mit einer Aliasbezeichnung verknüpfen, um die Identifikation zu erleichtern.
Konfigurieren der iSCSI-Host-Ports Die Standardmethode zum Konfigurieren der iSCSI-Host-Ports für IPv4-Adressierung ist DHCP. Verwenden Sie stets diese Methode, wenn Ihr Netzwerk über DHCP-Server verfügt. Es ist ratsam, den iSCSI-Ports statische DHCP-Adressen zuzuweisen, um stetige Konnektivität zu gewährleisten. Für Ipv6-Adressierung ist die Standardmethode statuslose Autokonfigurierung. Verwenden Sie stets diese Methode für IPv6. So konfigurieren Sie die iSCSI-Host-Ports: 1.
Stellung Beschreibung ANMERKUNG: Für weitere Informationen über die Erstellung und Konfiguration des VLANs mit dem MD Support Manager, klicken Sie im AMW auf die Registerkarte Unterstützung und anschließend auf Online-Hilfe anzeigen. Ethernet-Priorität Die Netzwerkpriorität kann in Stufen – von der niedrigsten bis zur höchsten – vergeben werden. Für die Zuordnungen sind die Netzwerkverwalter zuständig.
Das Fenster iSCSI-Statistik anzeigen wird angezeigt. 2. Wählen Sie die iSCSI-Statistikart aus, die Sie im Bereich iSCSI-Statistikart anzeigen möchten. Sie haben die Auswahl zwischen: • Ethernet MAC-Statistik • Ethernet TCP/IP-Statistik • Ziel (Protokoll)-Statistik • Statistik für lokalen Initiator (Protokoll) 3. Wählen Sie im Bereich Optionen Folgendes aus: • • Rohstatistik – Zum Anzeigen der Rohstatistik. Die Rohstatistik umfasst sämtliche seit dem Start der Controller gesammelten statistischen Daten.
5 Ereignisüberwachung Der Dell EMC PowerVault Modular Disk Storage Manager beinhaltet eine Ereignisüberwachung. Die Ereignisüberwachung wird fortlaufend im Hintergrund ausgeführt und überwacht die Aktivität auf den verwalteten Speicher-Arrays. Wenn die Ereignisüberwachung ein kritisches Problem erkennt, kann sie einen Host oder ein Remote-System per E-Mail, SNMP-Trapmeldungen (Simple Network Management Protocol) oder beidem benachrichtigen.
Um die Ereignisüberwachung zu deaktivieren, starten Sie die Terminal-Emulationsanwendung (console ox xterm). Geben Sie an der Eingabeaufforderung SMmonitor stop ein und drücken Sie die Eingabetaste. Nachdem das Programm beendet wurde, wird die folgende Meldung angezeigt: Stopping Monitor process. (Überwachung wird beendet).
6 Informationen zum Host Themen: • • • • • • • Konfigurieren des Hostzugriffs Verwenden der Registerkarte „Host-Zuordnungen“ Entfernen des Host-Zugriffs Verwalten von Host-Gruppen Erstellen einer Host-Gruppe E/A-Datenpfadschutz Verwalten von Host-Port-Kennungen Konfigurieren des Hostzugriffs Dell EMC PowerVault Modular Disk Storage Manager (MD Storage Manager) setzt sich aus mehreren Modulen zusammen.
Verwenden der Registerkarte „HostZuordnungen“ In der Registerkarte Host-Zuordnungen können Sie: • • Hosts oder Host-Gruppen definieren Zuordnungen zu den ausgewählten Host-Gruppen hinzufügen Definieren eines Hosts Sie können den Assistenten zum Definieren von Hosts im AMW benutzen, um einen Host für ein Speicher-Array zu definieren. Es können entweder eine bekannte nicht zugewiesene Host-Port-Kennung oder eine neue Host-Port-Kennung hinzugefügt werden.
Entfernen des Host-Zugriffs So entfernen Sie einen Host-Zugriff: 1. Wählen Sie im AMW die Registerkarte Host-Zuordnungen. 2. Wählen Sie den Hostknoten in der Struktur auf der linken Seite. 3. Führen Sie einen der folgenden Vorgänge durch: • • Wählen Sie im Menü Host-Zuordnungen > Host > Entfernen. Klicken Sie mit der rechten Maustaste auf den Host-Knoten und wählen Sie Entfernen aus dem Popup-Menü aus. Das Dialogfeld Bestätigung entfernen wird angezeigt. 4. Geben Sie yes ein. 5. Klicken Sie auf OK.
Verschieben eines Hosts in eine andere Host-Gruppe Um einen Host zu einer anderen Host-Gruppe zu verschieben: 1. Wählen Sie im AMW die Registerkarte Host-Zuordnungen aus und wählen Sie in der Strukturansicht den Host-Knoten aus. 2. Führen Sie einen der folgenden Vorgänge durch: • • Wählen Sie im Menü Host-Zuordnungen > Host > Verschieben. Klicken Sie mit der rechten Maustaste auf den Host-Knoten und wählen Sie Verschieben aus dem Popup-Menü aus. Das Dialogfenster Host verschieben erscheint. 3.
Um den Host-Kontext-Agenten auf Linux zu starten oder anzuhalten, geben Sie bei der Eingabeaufforderung die folgenden Befehle ein: SMagent start SMagent stop Der SMagent muss nach folgenden Änderungen angehalten und neu gestartet werden: • • Versetzen eines Controllers in den Offline-Status oder Austausch eines Controllers Host-zu-Array-Verbindungen von einem Linux-Host-Server entfernen bzw. diesem zuordnen. Um den Host-Kontext-Agenten auf Windows zu starten oder anzuhalten: 1.
• Wählen Sie in der Menüleiste Host-Zuordnungen > Host-Port-Kennungen verwalten aus. Das Dialogfeld Host-Port-Kennungen verwalten wird angezeigt. 3. So verwalten Sie die Host-Port-Kennungen in der Liste Host-Port-Kennungen anzeigen, die folgenden zugewiesen sind: 4. 5. 6. 7. • Wählen Sie den Host aus der Liste der dem Speicher-Array zugewiesenen Hosts aus. • Wählen Sie Alle Hosts in der Liste der dem Speicher-Array zugewiesenen Hosts aus.
7 Laufwerksgruppen, virtuelle Standardlaufwerke und schlanke virtuelle Laufwerke Themen: • • • • • • • • • • • • • • Erstellen von Laufwerksgruppen und virtuellen Laufwerken Schlanke, virtuelle Laufwerke Auswählen eines geeigneten physikalischen Laufwerkstyps Sicherheit für physikalische Laufwerke mit selbstverschlüsselndem Laufwerk Konfigurieren physikalischer Laufwerke als Hot-Spares Sicherheit für physikalische Laufwerke Gehäuseausfallschutz Schubladenausfallschutz Host-Zuweisung an virtuelle Laufwerke
Eine Laufwerksgruppe sollte entsprechend der verknüpften Aufgaben und Unteraufgaben organisiert werden. Wenn Sie beispielsweise eine Laufwerksgruppe für die Buchhaltungsabteilung erstellen, können Sie virtuelle Laufwerke erstellen, die den verschiedenen Arten von Buchhaltung entsprechen, die in der Abteilung durchgeführt werden: Debitoren, Kreditoren, interne Rechnungen usw.
ANMERKUNG: Um mehrere physikalische Laufwerke in einem Vorgang auszuwählen, halten Sie die Taste oder gedrückt und wählen Sie weitere physikalische Laufwerke aus. c. Klicken Sie auf Kapazität berechnen, um die Kapazität der neuen Laufwerksgruppe anzuzeigen. d. Klicken Sie auf Finish (Fertigstellen).
5. Wählen Sie in der Liste Zuweisung an Host einen entsprechenden Host oder wählen Sie Später zuweisen aus. 6. Im Bereich Datenservice (DS)-Attribute haben Sie die Wahl zwischen: • • Datensicherheit (DA) auf dem neuen virtuellen Laufwerk aktivieren SSD-Cache verwenden 7. Wählen Sie in der Liste E/A-Merkmale des virtuellen Laufwerks den entsprechenden Typ der E/A-Merkmale des virtuellen Laufwerks.
Ändern der Cache-Einstellungen virtueller Laufwerke Sie können die Cache-Einstellungen für ein einzelnes virtuelles Laufwerk oder für mehrere virtuelle Laufwerke eines Speicher-Arrays festlegen.
Ändern der Segmentgröße eines virtuellen Laufwerks Sie können die Segmentgröße auf einem ausgewählten virtuellen Laufwerk ändern. Während dieses Vorgangs wird die E/A-Leistung beeinträchtigt, Ihre Daten stehen jedoch weiterhin zur Verfügung. Beachten Sie diese Richtlinien für das weitere Vorgehen beim Ändern der Segmentgröße: • • • Dieser Vorgang kann nicht abgebrochen werden, nachdem er gestartet wurde. Starten Sie diesen Vorgang nicht, wenn sich die Laufwerksgruppe nicht im Status „Optimal“ befindet.
4. Wählen Sie eine der folgenden Optionen: • • Schreib-Cache mit Datenreplizierung aktivieren – Wählen Sie diese Option zur Replizierung von zwischengespeicherten Daten über zwei redundante RAID-Controller-Module der gleichen Cache-Größe hinweg. Schreib-Cache ohne Akkus aktivieren – Wählen Sie diese Option aus, um zuzulassen, dass das Schreib-Caching sogar dann fortgesetzt wird, wenn die Akkus des RAID-Controller-Moduls vollständig entladen wurden, nicht vollständig aufgeladen, oder nicht vorhanden sind.
Ändern der Kapazität eines bestehenden schlanken virtuellen Laufwerks Falls die Menge des vom Host für Lese-/Schreibvorgänge verwendeten Speicherraums (manchmal als konsumierte Kapazität bezeichnet) die Menge der physischen, einem virtuellen Standardlaufwerk zugeordneten Kapazität überschreitet, kann das Speicher-Array zusätzliche Schreibanforderungen erst dann wieder annehmen, wenn die physische Kapazität erhöht wird.
Status schlanker virtueller Laufwerke Im folgenden werden die Zustände des virtuellen Laufwerks aufgeführt wie im MD Speicher-Manager angezeigt: • • Optimal — Das virtuelle Laufwerk funktioniert normal. Voll — Die physische Kapazität eines schlanken virtuellen Laufwerks ist voll, und es können nicht mehr als zwei HostSchreibanforderungen verarbeitet werden.
Initialisieren eines schlanken virtuellen Laufwerks VORSICHT: Möglicher Verlust von Daten – Durch das Initialisieren eines schlanken virtuellen Laufwerks werden alle Daten vom virtuellen Laufwerk gelöscht. Wenn sie Fragen haben, kontaktieren Sie den technischen Support vor Durchführung dieses Verfahrens. Ein schlankes virtuelles Laufwerk wird bei der Erstellung automatisch initialisiert.
1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie das schlanke virtuelle Laufwerk aus, das Sie initialisieren möchten. Schlanke virtuelle Laufwerke sind unter dem Laufwerkspool-Knoten aufgelistet. 3. Wählen Sie Speicher > Virtuelles Laufwerk > Erweitert > Initialisieren aus. Das Fenster Virtuelles Ziellaufwerk auswählen wird angezeigt. 4. Wählen Sie Anderes Repository verwenden. 5.
ANMERKUNG: Sie können schlanke virtuelle Laufwerke nur von Laufwerkspools erstellen, nicht jedoch von Laufwerksgruppen. 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie das schlanke virtuelle Laufwerk aus, das Sie initialisieren möchten. Schlanke virtuelle Laufwerke sind unter dem Laufwerkspool-Knoten aufgelistet. 3. Wählen Sie Speicher > Virtuelles Laufwerk > Erweitert > Initialisieren aus. Das Fenster Virtuelles Ziellaufwerk auswählen wird angezeigt. 4.
Verwenden der Zuordnungsaufhebung für ein schlankes virtuelles Laufwerk In Version 8.25 wurde das Feature für schlanke Speicherzuweisung (Thin Provisioning erweitert, um den UNMAP-Befehl, über die Kommandozeile zu unterstützen. Alle virtuelle Laufwerke mit schlanker Speicherzuweisung, die für einen Speicher-Array vor einer Aktualisierung auf Version 8.25 konfiguriert wurden, sind nach der Aktualisierung weiterhin verfügbar und unterstützen den Befehl UNMAP.
gemeinsam genutzte Sicherheitsschlüssel stellt den Lese- und Schreibzugriff auf die physikalischen Laufwerke bereit, während der Verschlüsselungsschlüssel auf jedem physikalischen Laufwerk zur Verschlüsselung der Daten verwendet wird. Ein sicherheitsfähiges physikalisches Laufwerk arbeitet wie jedes andere physikalische Laufwerk auch, bis es sicherheitsaktiviert wird.
• Alle von Ihnen auf der Registerkarte Hardware (Hardware) ausgewählten Laufwerke sind sicherheitsfähige physikalische Laufwerke. Sie können sicherheitsaktivierte physikalische Laufwerke löschen, sodass Sie die physikalischen Laufwerke in einer anderen Laufwerksgruppe oder in einem anderen Speicher-Array wiederverwenden können. Wenn Sie sicherheitsaktivierte physikalische Laufwerke löschen, dann stellen Sie sicher, dass die Daten nicht gelesen werden können.
• • • • • zwischen acht und 32 Buchstaben enthalten. mindestens einen Großbuchstaben enthalten. mindestens einen Kleinbuchstaben enthalten. mindestens eine Zahl enthalten. mindestens ein nicht-alphanumerisches Zeichen enthalten, z.B. < > @ + Das von Ihnen eingegebene Kennwort wird maskiert. ANMERKUNG: Schlüssel erstellen ist aktiv, nur wenn das Passwort den zuvor wewähnten Kriterien entspricht. 9.
• • • Es muss mindestens einen Kleinbuchstaben enthalten. Es muss mindestens eine Zahl enthalten. Sie muss mindestens ein nicht-alphanumerisches Zeichen enthalten, z. B. < > @ +. Das von Ihnen eingegebene Kennwort wird maskiert. 6. Geben Sie in Kennwort bestätigen erneut exakt die gleiche Zeichenkette ein, die Sie in Kennwort eingegeben haben. Notieren Sie sich das von Ihnen eingegebene Kennwort und die Sicherheitsschlüsselkennung, die ihr zugeordnet ist.
geschrieben werden können. Um die physikalischen Laufwerke zu entsperren, müssen Sie den Sicherheitsschlüssel des ursprünglichen Speicher-Arrays bereitstellen. Der Sicherheitsschlüssel des neuen Speicher-Arrays ist unterschiedlich und kann die physikalischen Laufwerke nicht entsperren. Sie müssen den Sicherheitsschlüssel durch eine Sicherheitsschlüsseldatei bereitstellen, die auf dem ursprünglichen Speicher-Array gespeichert wurde.
• • • • View/change current hot spare coverage (Aktuelle Hot-Spare-Abdeckung anzeigen/ändern) – für das Überprüfen der HotSpare-Abdeckung und für das Zuweisen bzw. Aufheben der Zuordnung von physikalischen Hot-Spare-Laufwerken, falls notwendig. Siehe Schritt 5.
Schutz für physikalische Hot-Spare-Laufwerke Sie können physikalische Hot-Spare-Laufwerke als zusätzlichen Schutz Ihrer Daten vor in Laufwerksgruppen der RAID-Level 1 oder RAIDLevel 5 auftretenden physikalischen Laufwerksfehlern verwenden. Steht bei Ausfall eines physikalischen Laufwerks ein physikalisches HotSpare-Laufwerk zur Verfügung, verwendet das RAID-Controller-Modul Konsistenzdaten, um die Daten des ausgefallenen physikalischen Laufwerks zu rekonstruieren.
Wenn der Strom aus- und wieder eingeschaltet wird, werden die Sicherheitsfunktionen bei allen physikalischen Laufwerken mit aktivierter Sicherheit in einen Status mit gesperrter Sicherheit versetzt. In diesem Status sind die Daten unzugänglich, bis der richtige Sicherheitsschlüssel durch einen Controller bereitgestellt wird.
Schubladenausfallschutz In Erweiterungsgehäusen, die schubladenbasierte physikalische Laufwerke enthalten, kann ein Schubladenausfall den Zugriff auf Daten auf den virtuellen Laufwerke einer Datenträgergruppe verhindern. Der Schutz vor Schubladenausfall für eine Datenträgergruppe basiert auf dem Standort der physikalischen Laufwerke, die die Datenträgergruppe ausmachen.
• • • Jeder Host hat einen eigenen LUN-Adressierungsraum. MD Storage Manager erlaubt es, dass die gleiche LUN von verschiedenen Hosts oder Host-Gruppen verwendet wird, um auf virtuelle Laufwerke eines Speicher-Arrays zuzugreifen. Alle Betriebssysteme haben nicht die gleiche Anzahl der verfügbaren LUNs. Sie können die Zuordnungen in der Registerkarte Zuordnungen im AMW-Fenster definieren. Siehe Das Verwenden der Registerkarte „Host-Zuordnungen“.
Ändern und Entfernen der Zuordnung eines Hosts an ein virtuelles Laufwerk Aus verschiedenen Gründen kann es notwendig sein, die Host-Zuordnung an ein virtuelles Laufwerk zu ändern oder zu entfernen – etwa bei einer falschen Zuordnung oder einer Neukonfiguration des Speicher-Arrays. Das Ändern oder Entfernen der Host-Zuordnung an ein virtuelles Laufwerk gilt für Hosts und Host-Gruppen.
1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus und wählen Sie ein virtuelles Laufwerk aus. 2. Wählen Sie im Menü den entsprechenden RAID-Controller-Modul-Steckplatz Speicher > Virtuelles Laufwerk > Ändern > Besitz/ Bevorzugter Pfad. 3. Klicken Sie auf Ja, um die Auswahl zu bestätigen. Entfernen von Host-Zuordnungen an virtuelle Laufwerke Um Host-Zuordnungen an virtuelle Laufwerke zu entfernen: 1. Wählen Sie im AMW die Registerkarte Host-Zuordnungen. 2.
• Wenn in der Laufwerksgruppe, die auf den neuen RAID-Level konvertiert werden soll nicht genügend Speicherpatz zur Verfügung steht, wird eine Fehlermeldung angezeigt und der Vorgang wird nicht fortgeführt. Falls Sie nicht zugeordnete physikalische Laufwerke haben, verwenden Sie die Option Storage (Speicher) > Disk Group (Laufwerksgruppe) > Add Physical Disks (Capacity) (Physikalische Laufwerke (Kapazität) hinzufügen), um der Laufwerksgruppe zusätzlichen Speicherplatz hinzuzufügen.
wobei mapth_x das Gerät ist, das Sie löschen möchten. 4. Löschen Sie die im Zusammenhang mit diesem Gerät stehenden Pfade mithilfe des folgenden Befehls: # echo 1 > /sys/block/sd_x/device/delete wobei sd_x den SD-Knoten (Laufwerksgerät) darstellt, der über den multipath-Befehl ausgegeben wird. Wiederholen Sie diesen Befehl für alle Pfade, die sich auf dieses Gerät beziehen. Beispiel: #echo 1 > /sys/block/sdf/device/delete #echo 1 > /sys/block/sde/device/delete 5.
auferlegte Grenze beschränkt. Wird ein bestimmter Host mit einem nicht eingeschränkten Host-Typ Teil einer spezifischen Speicherpartition, können Sie die Zuordnung in eine höhere LUN ändern. Speicherpartitionierung Eine Speicherpartition ist eine logische Einheit aus einem oder mehreren virtuellen Laufwerken, auf die entweder von einem einzelnen Host oder gemeinsam von den Hosts einer Host-Gruppe zugegriffen wird.
1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie eine Laufwerksgruppe aus. 3. Wählen Sie in der Menüleiste Storage (Speicher) > Disk Group (Laufwerksgruppe) > Add Physical Disks (Capacity) (Physikalische Laufwerke (Kapazität) hinzufügen). Alternativ dazu können Sie mit der rechten Maustaste auf die Laufwerksgruppe klicken und im Popup-Menü Add Physical Disks (Capacity) (Physikalische Laufwerke (Kapazität) hinzufügen) auswählen.
ANMERKUNG: Sie können auch die Befehlszeilenoberfläche (CLI) auf Windows- und Linux-Hosts verwenden, um die Kapazität eines virtuellen Laufwerks zu erhöhen. Weitere Informationen dazu finden Sie im Handbuch zur Befehlszeilenoberfläche für Dell EMC PowerVault-Speicherarrays der MD 34XX/38XX-Reihe.
1. Speichen Sie die Speicher-Array-Konfiguration 2. Stoppen Sie alle Datenübertragungen und unmounten oder trennen Sie die auf den virtuellen Laufwerken der Laufwerksgruppe vorhandenen Dateisysteme. 3. Sichern Sie die auf den virtuellen Laufwerken in der Laufwerksgruppe gespeicherten Daten. 4. Bestimmen Sie den physikalischen Standort der Laufwerksgruppe und kennzeichnen Sie die physikalischen Laufwerk mit entsprechenden Beschriftungen. 5. Schalten Sie die Laufwerksgruppe offline. 6.
Medienüberprüfung in Speicher-Arrays Bei der Medienüberprüfung handelt es sich um einen lang andauernden Vorgang, bei dem virtuelle Laufwerke daraufhin untersucht werden, ob auf die Daten zugegriffen werden kann. Dabei werden Medienfehler gefunden, bevor die normale Lese- und Schreibaktivität unterbrochen wird und Fehler im Ereignisprotokoll aufgeführt werden. ANMERKUNG: Sie können auf einem aus SSDs (Solid State Disks) gebildeten virtuellen Laufwerk keine Medienüberprüfungen im Hintergrund aktivieren.
3. Wählen Sie Mediensuche vorübergehend aufheben aus. ANMERKUNG: Dies wird auf alle virtuellen Laufwerke der Laufwerksgruppe angewendet. 4. Klicken Sie auf OK.
8 Laufwerkspools und virtuelle Laufwerke von Laufwerkspools Das Laufwerkspooling ermöglicht Ihnen die wahllose Verteilung von Daten von jedem virtuellen Laufwerk über einen Satz von physikalischen Laufwerke hinweg. Das Laufwerkspooling stellt den RAID-Schutz und konsistente Leistung über einen Satz physikalischer Laufwerke hinweg bereit, die logisch im Speicher-Array zusammengruppiert sind.
Unterschied zwischen Laufwerksgruppen und Laufwerkspools Ebenso wie bei einer Laufwerksgruppe können Sie ein oder mehrere virtuelle Laufwerke in einem Laufwerkpool erstellen. Ein Laufwerkpool unterscheidet sich jedoch von einer Laufwerksgruppe darin, wie die Daten über die physischen Laufwerke verteilt werden, aus denen der Laufwerkpool besteht. Die Dynamic Disk Pool (DDP)-Funktion verteilt Daten und Reservekapazität auf dynamische Weise und schützt Informationen über einen Pool von Laufwerken hinweg.
ANMERKUNG: Sie können SED-fähige und nicht-SED-fähige physikalische Laufwerke zusammen verwenden. Die Verschlüsselungfunktion der SED-fähigen physikalischen Laufwerke steht jedoch in diesem Fall nicht zur Verfügung, da die entsprechenden physikalischen Laufwerksattribute nicht übereinstimmen. Auf Grundlage des von Ihnen ausgewählten physikalischen Laufwerkstyps und Sicherheitstyps werden in der Tabelle Laufwerkspool-Kandidaten eine oder mehrere Laufwerkspool-Konfigurationen angezeigt. 6.
schließen, und wählen Sie im AMW Storage Array (Speicher-Array) > Disk Pool (Laufwerkspool) > Add Physical disks (Capacity) (Physikalische Laufwerke (Kapazität) hinzufügen). Wenn einem Speicher-Array zusätzliche physikalische Laufwerke hinzugefügt werden, während das Dialogfeld Automatic Configuration (Automatische Konfiguration) geöffnet ist, können Sie auf Update (Aktualisieren) klicken, um zusätzliche physikalische Laufwerke zu erkennen.
Konfigurieren von Warnbenachrichtigungen für einen Laufwerkspool Sie können den MD Storage Manager so konfigurieren, dass Warnbenachrichtigungen gesendet werden, wenn der unkonfigurierte (freie) Speicherplatz eines Laufwerkspools einen bestimmten Prozentwert erreicht. Die Benachrichtigungseinstellungen können nach dem Erstellen eines Laufwerkspools geändert werden. So konfigurieren Sie Warnbenachrichtigungen für einen Laufwerkspool: 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2.
5. Klicken Sie auf Hinzufügen. Konfigurieren des vorgehaltenen Speicherplatzes eines Laufwerkspools Der vorgehaltene Speicherplatz in einem Laufwerkspool ist für die Datenwiederherstellung bei Ausfall physikalischer Laufwerke reserviert. So konfigurieren Sie den vorgehaltenen Speicherplatz in einem Laufwerkspool: 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie den Laufwerkspool aus. 3. Wählen Sie im Menü Speicher > Laufwerkspool > Ändern > Einstellungen.
Ändern der RAID-Controller-Modul-Besitzrechte einer Laufwerksgruppe Sie können die RAID-Controller-Modul-Besitzrechte eines Laufwerkspools ändern und festlegen, welches RAID-Controller-Modul Besitzer der virtuellen Laufwerke im Laufwerkspool ist. Wenn Sie die RAID-Controller-Modul-Besitzrechte auf Laufwerkspool-Ebene ändern, führt dies dazu, dass jedes virtuelle Laufwerk in diesem Laufwerkspool auf das andere RAID-Controller-Modul übertragen wird und einen neuen E/A-Pfad verwendet.
• • Das virtuelle Laufwerk wird in der Tabelle „Virtuelles Laufwerk“ ausgewählt. VORSICHT: Möglicher Verlust des Datenzugriffs – Es liegt ein schwerwiegender Konsistenzfehler vor, der einen dauerhaften Datenverlust zur Folge haben könnte. Der Status der Konsistenzprüfung wird in der Spalte Zugeordneter Status angezeigt. Löschen eines Laufwerkspools Verwenden Sie die Option Delete (Löschen), um einen Laufwerkspool und alle virtuellen Laufwerke im Laufwerkspool zu löschen.
des Speicher-Arrays. Der Fensterbereich „Eigenschaften“ zeigt detaillierte Informationen über die in der Strukturansicht ausgewählte Komponente an. 2. Führen Sie eine dieser Aktionen durch, um die einer Komponente zugeordneten physikalischen Komponenten anzuzeigen: • • • Klicken Sie mit der rechten Maustaste auf eine Komponente und wählen Sie Zugewiesene physikalische Komponenten anzeigen.
Ändern der Kapazität eines bestehenden schlanken virtuellen Laufwerks Falls die Menge des vom Host für Lese-/Schreibvorgänge verwendeten Speicherraums (manchmal als konsumierte Kapazität bezeichnet) die Menge der physischen, einem virtuellen Standardlaufwerk zugeordneten Kapazität überschreitet, kann das Speicher-Array zusätzliche Schreibanforderungen erst dann wieder annehmen, wenn die physische Kapazität erhöht wird.
11. Geben Sie im Feld Preferred capacity (Bevorzugte Kapazität) die anfängliche physikalische Kapazität des virtuellen Laufwerks ein, und legen Sie mithilfe der Liste Units (Einheiten) fest, welche Speicherplatzeinheiten (MB, GB oder TB) verwendet werden sollen. ANMERKUNG: Die physikalische Kapazität ist der physikalische Speicherplatz eines Laufwerks, der aktuell für Schreibanfragen reserviert ist. Die physikalische Kapazität muss mindestens 4 GB betragen und ist auf maximal 256 GB beschränkt.
9 Verwenden von SSD-Cache Die SSD-Cache-Funktion verwendet physikalische Solid-State-Laufwerke (SSDs), um die Nur-Lesen-Leistung in Ihrem Speicher-Array zu verbessern. Physikalische SSD-Laufwerke sind logisch gruppiert, um einen sekundären Cache bereitzustellen, der zusammen mit dem dem primären Cache im RAID-Controller-Modul-Speicher verwendet werden soll.
• • • Dateisystem Datenbank Webserver Es stehen Ihnen auch folgende Optionen zur Verfügung: • • • Die Kapazität des SSD-Cache von einer Liste möglicher Kandidaten, die aus verschiedenen Zählungen von physischen SSDLaufwerken besteht.
• • Klicken Sie mit der rechten Maustaste auf den SSD-Cache und wählen Sie Zugewiesene physikalische Komponenten anzeigen. Klicken Sie in der Tabellenansicht für den SSD-Cache auf Zugewiesene physikalische Komponenten anzeigen. Das Fenster Zugewiesene physikalische Komponenten anzeigen wird angezeigt. 3. Um einen physikalischen Laufwerkstyp anzuzeigen, wählen Sie einen Laufwerkstyp von Physikalischer Laufwerkstyp und klicken Sie auf Anzeigen. Um den Abschnitt auszublenden, klicken Sie auf ausblenden. 4.
2. Wählen Sie in der Strukturansicht den SSD-Cache aus dem Sie physikalische Laufwerke entfernen möchten. 3. Führen Sie eine der folgenden Aktionen aus: • • Klicken Sie in der Menüleiste auf Speicher > SSD-Cache > Physikalische Laufwerke (Speicherplatz) entfernen. Klicken Sie mit der rechten Maustaste auf SSD-Cache und wählen Sie Physikalische Laufwerke (Speicherplatz) entfernen aus. Das Fenster Physikalische Laufwerke (Speicherplatz) entfernen wird angezeigt. 4.
Das Fenster Löschen des SSD-Cache bestätigen wird angezeigt. 3. Geben Sie zur Bestätigung yes ein und klicken Sie auf Delete (Löschen). Verwenden des Leistungsmodellierungstools Das SSD-Cache-Leistungsmodellierungstool unterstützt Sie dabei, die Leistungssteigerung der SSD-Cache-Kapazität zu bestimmen, wenn Sie das Leistungsmodellierungstool mit einer Auslastung ausführen, die der Last unter tatsächlichen Arbeitsbedingungen entspricht.
10 Erweiterungsfunktion – Virtuelles SnapshotLaufwerk Die folgenden Premiumfunktionen für virtuelle Laufwerk-Snapshots werden auf dem MD-Speicherarray unterstützt: • Virtuelle Snapshot-Laufwerke, die mehrere zeitgerechte (PiT) Gruppen verwenden Ein Snapshot-Abbild ist ein logisches Abbild des Inhalts eines zugehörigen virtuellen Basislaufwerks, das zu einem bestimmten Zeitpunkt erstellt wurde und das oft als Wiederherstellungspunkt bekannt ist.
• • Ein Read-Only (schreibgeschütztes) virtuelles Snapshot-Laufwerk gewährt der Host-Anwendung Lesezugriff auf eine Kopie der im Snapshot-Abbild enthaltenen Daten. Der Host kann jedoch keine Änderungen am Snapshot-Abbild vornehmen. Ein schreibgeschütztes (Read-Only) virtuelles Snapshot-Laufwerk erfordert ein zugehöriges Repository.
• • • • • Snapshot-Abbilder können für eine Konsistenzgruppe erstellt werden, um konsistente Snapshot-Abbilder zwischen allen virtuellen Mitgliedslaufwerken zu erstellen. Rollbacks können für Konsistenzgruppen durchgeführt werden. Ein virtuelles Laufwerk kann zu mehreren Konsistenzgruppen gehören. Nur virtuelle Standardlaufwerke und schlanke virtuelle Laufwerke können in einer Konsistenzgruppe aufgenommen werden.
Erstellen von Snapshot-Abbildern Ein Snapshot-Abbild ist ein zu einem bestimmten Zeitpunkt erstelltes logisches Bild des Inhalts eines zugeordneten virtuellen Basislaufwerks. Mit Snapshot-Abbildern können Sie viel schneller mehrfache Kopien von Produktionsdaten auf Ihrem Speicher-Array erstellen. Snapshot-Abbilder erfassen Änderungen an der Datenquelle ab dem Erstellungszeitpunkt des jeweiligen Snapshot-Abbilds.
Verwenden Sie die Methode Manual (Manuell) nur dann, wenn Sie mit den Themen der Konsistenz und der optimalen Konfiguration physikalischer Laufwerke völlig vertraut sind.
Einrichten eines Zeitplans für Snapshot-Abbilder Der MD-Storage-Manager ermöglicht Ihnen, Zeitpläne zum regelmäßigen Erstellen von Snapshot-Abbildern für die Dateiwiederherstellung und Datensicherung einzurichten. Sie können einen Zeitplan für eine vorhandene Snapshot-Gruppe oder Konsistenzgruppe oder bereits beim Erstellen einer Snapshot-Gruppe oder Konsistenzgruppe einrichten.
So bearbeiten Sie einen Zeitplan: 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie die Snapshot-Gruppe oder die Konsistenzgruppe aus, deren Zeitplan Sie bearbeiten möchten. 3. Führen Sie eine der folgenden Aktionen aus: • • Kopierdienste > Snapshot-Gruppe > Snapshot-Abbild-Zeitplan bearbeiten. Kopierdienste > Konsistenzgruppen-Snapshot-Abbild > Zeitplan erstellen/bearbeiten. Das Fenster Snapshot-Abbild-Zeitplan bearbeiten wird angezeigt. 4.
ANMERKUNG: Sie können auch mithilfe der Befehlszeile von mehreren Snapshot-Abbildern gleichzeitig einen RollbackVorgang starten, einen Rollback-Vorgang abbrechen, einen Rollback-Vorgang wieder aufnehmen, die Priorität eines Rollback-Vorgangs ändern und den Fortschritt eines Rollback-Vorgangs anzeigen. Starten eines Snapshot-Rollbacks 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2.
• • Den Inhalt des virtuellen Basislaufwerks reinitialisieren. Einen neuen Rollback-Vorgang ausführen, um das virtuelle Basislaufwerk wiederherzustellen (entweder mithilfe des gleichen Snapshot-Abbilds, das in der Option Rollback abbrechen verwendet wurde, oder mithilfe eines anderen Snapshot-Abbilds, zur Ausführung eines neuen Rollback-Vorgangs).
• Wählen Sie eine Konsistenzgruppe eines virtuellen Basislaufwerks oder eines virtuellen Mitgliedslaufwerks einer Konsistenzgruppe aus, und wählen Sie dann Copy Services (Kopierdienste) > Consistency Group Snapshot Image (Snapshot-Abbild einer Konsistenzgruppe > Rollback (Rollback) > Change Priority (Priorität ändern) aus. Das Fenster Rollback-Priorität ändern wird angezeigt. 3. Legen Sie im Bereich „Rollback-Priorität“ mithilfe des Schiebereglers eine Priorität für den Rollback-Vorgang fest.
• • In der Navigationsstruktur wird die Snapshot-Gruppe mit ihren Eigenschaften unter dem virtuellen Laufwerksknoten für das zugeordnete virtuelle Basislaufwerk angezeigt. Wenn Create the first Snapshot Image Now (Erstes Snapshot-Abbild jetzt erstellen) aktiviert war, legt das System eine Kopie des zugeordneten virtuellen Basislaufwerks an, woraufhin das Dialogfeld Snapshot Image Successfully Created (SnapshotAbbild erfolgreich erstellt) angezeigt wird.
b. Klicken Sie auf OK. 8. Wählen Sie Erweiterte Optionen anzeigen aus, und übernehmen oder ändern Sie dann je nach Bedarf die folgenden Standardeinstellungen: 9. Klicken Sie auf Finish (Fertigstellen). Ändern der Einstellungen einer Snapshot-Gruppe Verwenden Sie die Option Einstellungen für Snapshot-Gruppe ändern, um die beim Erstellen der Snapshot-Gruppe konfigurierten Einstellungen für das automatische Löschen und für das Snapshot-Gruppen-Repository zu ändern.
So löschen Sie die Snapshot-Gruppe: 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie die Snapshot-Gruppe aus, die Sie löschen möchten, und wählen Sie dann die Menüfolge Kopierdienste > SnapshotGruppe > Löschen aus. Das Fenster Löschen bestätigen wird angezeigt. 3. Wählen Sie Alle diesem Objekt zugeordneten Repositorys löschen? aus, wenn Sie das der Snapshot-Gruppe zugeordnete Repository löschen möchten. 4.
Erstellen einer Konsistenzgruppe Eine Konsistenzgruppe besteht aus simultanen Snapshots mehrerer virtueller Laufwerke, wodurch konsistente Kopien einer Gruppe von virtuellen Laufwerken gewährleistet werden. Jedes virtuelle Laufwerk, das zu einer Konsistenzgruppe gehört, wird als virtuelles Mitgliedslaufwerk bezeichnet. Wenn Sie ein virtuelles Laufwerk zu einer Konsistenzgruppe hinzufügen, erstellt das System automatisch eine neue Snapshot-Gruppe, die diesem virtuellen Mitgliedslaufwerk entspricht.
Manuelles erstellen eines Konsistenzgruppen-Repositorys Während der Erstellung einer Konsistenzgruppe wird ein Konsistenzgruppen-Repository erstellt, in dem die Daten aller in der Gruppe vorhandenen Snapshot-Abbilder gespeichert werden. Ein Konsistenzgruppen-Repository wird eingangs mit einem einzigen virtuellen Repository-Laufwerk erstellt. Jedes virtuelle Laufwerk, das zu einer Konsistenzgruppe gehört, wird als virtuelles Mitgliedslaufwerk bezeichnet.
Umbenennen einer Konsistenzgruppe Verwenden Sie die Option Konsistenzgruppe umbenennen, um den Namen der Konsistenzgruppe zu ändern, wenn der aktuelle Name keine Bedeutung mehr trägt oder ungeeignet ist. Beachten Sie beim Benennen einer Konsistenzgruppe die folgenden Richtlinien: • • • • • Ein Name kann aus Buchstaben, Zahlen und den Sonderzeichen Unterstrich (_), Bindestrich (-) und Raute (#) bestehen. Wenn Sie irgendwelche anderen Zeichen wählen, wird eine Fehlermeldung angezeigt.
2. Wählen Sie im Konsistenzgruppen-Kategorieknoten die Konsistenzgruppe aus, die Sie ändern möchten, und wählen Sie dann Kopierdienste > Konsistenzgruppe > Einstellungen ändern aus. Das Fenster Konsistenzgruppeneinstellungen ändern wird angezeigt. 3. Ändern Sie die Konsistenzgruppeneinstellungen wie erforderlich. 4. Klicken Sie auf OK, um die Änderungen an der Konsistenzgruppe zu übernehmen.
Entfernen eines virtuellen Mitgliedslaufwerks von einer Konsistenzgruppe Mithilfe der Option Virtuelle Mitgliedslaufwerke entfernen können Sie ein virtuelles Mitgliedslaufwerk aus einer vorhandenen Konsistenzgruppe entfernen. Wenn Sie ein virtuelles Mitgliedslaufwerk von einer Konsistenzgruppe entfernen, löscht das System automatisch die diesem virtuellen Mitgliedslaufwerk zugeordnete Snapshot-Gruppe.
• Wenn Sie ein virtuelles Snapshot-Laufwerk für ein Snapshot-Abbild erstellen, und dieser Vorgang verbleibt im Status „Ausstehend“, so liegen dem folgende Bedingungen zugrunde: ○ Das virtuelle Basislaufwerk, das dieses Snapshot-Abbild enthält, ist Mitglied einer asynchronen Remote-Replikationsgruppe. ○ Für das virtuelle Basislaufwerk läuft derzeit eine Synchronisierung. Die Erstellung des Snapshot-Abbilds erfolgt nach Abschluss der Synchronisierung. Erstellen eines virtuellen Snapshot-Laufwerks 1.
• • • • • Jeder Host hat seinen eigenen Adressbereich für die logische Gerätenummer (LUN) und lässt zu, dass unterschiedliche HostGruppen oder Hosts mit derselben LUN auf virtuelle Snapshot-Laufwerke in einem Speicher-Array zugreifen. Für jedes virtuelle Snapshot-Laufwerk im Speicher-Array kann eine Zuordnung definiert werden. Zuordnungen werden von den Controllern im Speicher-Array gemeinsam genutzt.
Ändern der Einstellungen eines virtuellen SnapshotLaufwerks Verwenden Sie die Option Einstellungen für virtuelles Snapshot-Laufwerk ändern, um die beim Erstellen des virtuelles SnapshotLaufwerks konfigurierten Repository-Einstellungen zu ändern.
• Kopierdienste > Virtuelles Snapshot-Laufwerk einer Konsistenzgruppe > Deaktivieren. Das Fenster Deaktivieren des virtuellen Konsistenzgruppen-Snapshot-Laufwerks bestätigen wird angezeigt. 3. Geben Sie in das Textfeld yes ein und klicken Sie anschließend auf Disable (Deaktivieren), um das virtuelle Snapshot-Laufwerk zu deaktivieren.
Umbenennen eines virtuellen Snapshot-Laufwerks oder eines virtuellen Snapshot-Laufwerks einer Konsistenzgruppe Verwenden Sie die Option Virtuelles Snapshot-Laufwerk umbenennen, um den Namen eines virtuellen Snapshot-Laufwerks oder eines virtuellen Snapshot-Laufwerks einer Konsistenzgruppe zu ändern, wenn der aktuelle Name keine Bedeutung mehr trägt oder ungeeignet ist. Beachten Sie beim Benennen einer Konsistenzgruppe die folgenden Richtlinien: • • • Beschränken Sie den Namen auf 30 Zeichen.
• Das virtuelle Basislaufwerk, das dieses Snapshot-Abbild enthält, ist Mitglied einer asynchronen RemoteReplikationsgruppe. • Für das virtuelle Basislaufwerk findet eine Synchronisierung statt. Die Erstellung des Snapshot-Abbilds erfolgt nach Abschluss der Synchronisierung. So erstellen Sie ein virtuelles Snapshot-Laufwerk einer Konsistenzgruppe: 1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2.
• Wählen Sie Schreibgeschützt aus, um der Host-Anwendung LESEZUGRIFF auf eine Kopie der im Snapshot-Abbild enthaltenen Daten zu gewähren, wobei die Host-Anwendung in diesem Fall keine Änderungen am Snapshot-Abbild vornehmen kann. Ein schreibgeschütztes virtuelles Snapshot-Laufwerk hat kein zugehöriges Repository. 7. Wählen Sie jedes virtuelle Mitgliedslaufwerk in der Konsistenzgruppe aus, für das Sie ein virtuelles Snapshot-Laufwerk erstellen möchten.
3. Wählen Sie Manuell aus und klicken Sie auf Weiter, um die Einstellungen des Repository-Kandidaten für die Konsistenzgruppe zu definieren. Das Fenster Einstellungen für Repository eines virtuellen Snapshot-Laufwerks von Konsistenzgruppe - Manuell wird angezeigt. 4. Legen Sie auf Grundlage eines Prozentsatzes des virtuellen Basislaufwerks oder anhand der bevorzugten Kapazität fest, wie die Repository-Kandidaten für jedes virtuelle Mitgliedslaufwerk in der Konsistenzgruppe gefiltert werden sollen.
• • • • Das dem virtuellen Snapshot-Laufwerk oder dem virtuellen Snapshot-Laufwerk einer Konsistenzgruppe zugeordnete Repository (sofern das virtuelle Laufwerk mit Lese-/Schreibzugriff gekennzeichnet ist) bleibt beibehalten. Host-Zuordnungen und Host-Zugriff bleiben beibehalten (alle Lese-/Schreibanfragen schlagen fehl). Die Zuordnung des virtuellen Snapshot-Laufwerks oder des virtuellen Snapshot-Laufwerks einer Konsistenzgruppe zum aktuellen Snapshot-Abbild wird entfernt.
• Kopierdienste > Virtuelles Snapshot-Laufwerk > Wieder erstellen. Das Fenster Wiedererstellung des virtuellen Snapshot-Laufwerks bestätigen wird angezeigt. • Kopierdienste > Virtuelles Snapshot-Laufwerk einer Konsistenzgruppe > Wieder erstellen. Das Fenster Wiedererstellung des virtuellen Snapshot-Laufwerks bestätigen wird angezeigt. 3.
5. Wählen Sie entweder Mit Konsistenzprüfung oder Ohne Konsistenzprüfung aus und Klicken sie auf OK. Eine Konsistenzprüfung durchsucht die Blocks eines virtuellen RAID-Level-5-Laufwerks oder eines virtuellen RAID-Level-6-Laufwerks und überprüft die Konsistenzinformationen jedes Blocks. Eine Konsistenzprüfung vergleicht Datenblöcke auf replizierten physikalischen Laufwerken mit dem RAID-Level 1. Virtuelle Laufwerke mit dem RAID-Level 0 haben keine Datenkonsistenz.
Wird ein virtuelles Snapshot-Laufwerk oder ein virtuelles Snapshot-Laufwerk einer Konsistenzgruppe gelöscht, so führt das System die folgenden Schritte durch: • • Alle virtuellen Snapshot-Mitgliedslaufwerke werden gelöscht (für ein virtuelles Snapshot-Laufwerk einer Konsistenzgruppe). Alle entsprechenden Host-Zuordnungen werden gelöscht.
• • Physikalischer Laufwerkstyp – Eine Übereinstimmung liegt vor, wenn sich das virtuelle Basislaufwerk und das virtuelle RepositoryLaufwerk in einer Laufwerksgruppe oder einem Laufwerkspool mit identischen Attributen für den physikalischen Laufwerkstyp befinden. Sie können die Repository-Kapazität für ein schreibgeschütztes (read-only) virtuelles Snapshot-Laufwerk nicht erhöhen oder verringern, da für dieses kein Repository zugeordnet ist.
• • • Das allgemeine Repository enthält nur ein virtuelles Repository-Mitgliedslaufwerk. Wenn eines oder mehrere Snapshotabbilder vorhanden sind, die dem allgemeinen Repository zugewiesen sind. Wenn ein virtuelles Snapshot-Laufwerk oder ein virtuelles Mitgliedslaufwerk einer Konsistenzgruppe ausgeschaltet ist. Es gelten die folgenden Richtlinien: • • • • Sie können virtuelle Repository-Mitgliedslaufwerke nur in umgekehrter Reihenfolge, in der sie zugefügt wurden, entfernen.
1. Wählen Sie im AMW die Registerkarte Speicher- und Kopierdienste aus. 2. Wählen Sie das Speicherobjekt aus, das Sie reaktivieren möchten, und wählen Sie dann (je nach ausgewähltem Speicherobjekt) eine der nachstehenden Menüfolgen: • Copy Services (Kopierdienste) > Snapshot Group (Snapshot-Gruppe) > Advanced (Erweitert) > Revive (Reaktivieren).
11 Erweiterungsfunktion – virtuelle Laufwerkskopie ANMERKUNG: Eine virtuelle Laufwerkskopie überschreibt Daten auf dem virtuellen Ziellaufwerk. Bevor Sie eine virtuelle Laufwerkskopie starten, sollten Sie sicherstellen, dass Sie die Daten nicht mehr benötigen oder die Daten auf dem virtuellen Ziellaufwerk sichern.
• • • • • • • • • • • Einschränkungen bei virtuellen Laufwerkskopien Erstellen einer virtuellen Laufwerkskopie Bevorzugte Besitzrechte für RAID-Controller-Module Ausgefallenes RAID-Controller-Modul Kopienverwaltung Kopieren des virtuellen Laufwerks Leistung des Speicher-Arrays während der virtuellen Laufwerkskopie Festlegen der Kopierpriorität Anhalten einer virtuellen Laufwerkskopie Erneutes Kopieren eines virtuellen Laufwerks Entfernen von Kopienpaaren Typen virtueller Laufwerkskopien Sie können virtuel
Erstellen einer virtuellen Laufwerkskopie für ein MSCS-freigegebenes Laufwerk Zum Erstellen einer virtuellen Laufwerkskopie für ein Microsoft Cluster Server (MSCS)-freigegebenes Laufwerk, erstellen Sie einen Snapshot des virtuellen Laufwerks und verwenden dann das virtuelle Snapshot-Laufwerk als Quelllaufwerk für die virtuelle Laufwerkskopie.
Erstellen einer virtuellen Laufwerkskopie VORSICHT: Möglicher Datenverlust – Virtuelle Quelllaufwerke, die an einer virtuellen Laufwerkskopie beteiligt sind, stehen nur für Lese-E/A-Vorgänge zur Verfügung, während eine virtuelle Laufwerkskopie den Status „Wird durchgeführt“ oder „Ausstehend“ aufweist. Schreibanforderungen sind nach Abschluss der virtuellen Laufwerkskopie zulässig.
Änderungsvorgang auf einem virtuellen Quell- oder Ziellaufwerk ausgeführt wird, nachdem eine virtuelle Laufwerkskopie erstellt wurde, muss der Änderungsvorgang abgeschlossen sein, bevor die virtuelle Laufwerkskopie starten kann. Wenn eine virtuelle Laufwerkskopie den Status „Wird durchgeführt“ aufweist, werden keine Änderungsvorgänge durchgeführt.
Kopieren des virtuellen Laufwerks Sie können eine virtuelle Laufwerkskopie mithilfe des Assistenten für das Erstellen von Kopien erstellen. Eine virtuelle Laufwerkskopie versetzt das virtuelle Ziellaufwerk für Hosts automatisch in den Status „Schreibgeschützt“. Sie können dieses Attribut aktiviert lassen, um die Daten auf them virtuellen Ziellaufwerk zu erhalten.
Festlegen der Kopierpriorität Sie können die Kopienverwaltung verwenden, um die Rate, mit der eine virtuelle Laufwerkskopie abgeschlossen wird, für ein ausgewähltes Kopierpaar auswählen. Sie können die Kopierpriorität für ein Kopierpaar zu jedem der folgenden Zeitpunkte ändern: • • • Bevor die virtuelle Laufwerkskopie beginnt Während die virtuelle Laufwerkskopie den Status Wird durchgeführt aufweist Wenn Sie eine virtuelle Laufwerkskopie neu erstellen So setzen Sie die Kopierpriorität: 1.
Vorbereiten von Host-Servern zum erneuten Kopieren eines virtuellen Laufwerks ANMERKUNG: Bevor Sie eine Kopie eines virtuellen Quelllaufwerks erstellen, müssen Sie die gesamte Datenzugriffs (E/A)-Aktivität anhalten oder die Datenübertragung zum virtuellen Quelllaufwerk (und gegebenenfalls zum virtuellen Ziellaufwerk) aussetzen, um sicherzustellen, dass Sie eine genaues Abbild des virtuellen Quelllaufwerks zu dem gegebenen Zeitpunkt erfassen.
6. Legen Sie die Kopierpriorität fest. Es gibt fünf Kopierprioritätsstufen: niedrigste, niedrige, mittlere, hohe und höchste. Wenn die Kopierpriorität auf die niedrigste Stufe gesetzt ist, wird die E/A-Aktivität priorisiert wodurch der Vorgang der virtuellen Laufwerkskopie länger dauert. Wenn die Kopierpriorität auf die höchste Prioritätsstufe gesetzt ist, wird die virtuelle Laufwerkskopie priorisiert, was sich jedoch auf die E/AAktivität für das Speicher-Array auswirken könnte.
12 Device Mapper Multipath für Linux Themen: • • • • • • • Übersicht Mit Device Mapper Multipath-Geräten (DMMP) Schritte zur Konfiguration von Device Mapper Standardverfahren zum Neustarten eines Linux-Host-Servers Wichtige Informationen zu speziellen Partitionen Einschränkungen und bekannte Probleme Fehlerbehebung Übersicht Das MD Series-Speicher-Array verwendet das als Device Mapper (DM) bekannte Software-Framework des Linux-Betriebssystems, um so eine Multipath-Unterstützung auf Linux-Host-Servern zu e
2. Führen Sie einen Neustart durch, wenn Sie vom Installationsprogramm dazu aufgefordert werden – Das Installationsprogramm fordert am Ende der Installation zu einem notwendigen Neustart auf. 3. Konfigurieren mit MDCU – Nach dem Neustart des Host-Servers startet MDCU automatisch und befindet sich danach auf dem Desktop. Mit diesem Dienstprogramm können Sie neue und vorhandene MD Series-Speicher-Arrays in Ihrem Netzwerk schnell und einfach konfigurieren.
Führen Sie den folgenden Befehl aus, um eine Liste aller Multipath-Geräte anzuzeigen: # multipath –ll Die Ausgabe muss dem folgenden Beispiel ähnlich sein, in dem die Ausgabe für ein zugeordnetes virtuelles Laufwerk angezeigt wird: mpath1 (3600a0b80005ab177000017544a8d6b92) dm-0 DELL, MD3xxxx[size=5.0G][features=3 queue_if_no_path pg_init_retries 50][hwhandler=1 rdac][rw]\_ round-robin 0 [prio=6][active] \_ 5:0:0:0 sdc 8:32 [active][ready]\_ round-robin 0 [prio=1][enabled] \_ 4:0:0:0 sdb 8:16 [active][ghost
Wenn der Befehl erfolgreich ausgeführt wurde, wird keine Ausgabe angezeigt. Zum Überprüfen der erfolgreichen Ausführung und zum Anzeigen der exakten Partitionsbezeichnung, können Sie die foglenden Befehle verwenden, um die vollständigen zugewiesenen Partitionsnamen anzuzeigen.
ANMERKUNG: Das Startlaufwerk des Betriebssystems weist unter Umständen einen Eintrag in Bezug auf die Tabelle von Device Mapper Multipath auf. Hierauf hat der Befehl multipath –F keine Auswirkung. 4. Melden Sie sich von allen iSCSI-Sitzungen vom Host-Server zum Speicher-Array ab: # iscsiadm –m node --logout Wichtige Informationen zu speziellen Partitionen Wenn Device Mapper mit den MD Series-Speicher-Arrays verwendet wird, sind alle physikalischen Laufwerke einem Laufwerksgeräteknoten zugeordnet.
• • • • • • E/A kann hängen, wenn der Host-Server oder das Speicher-Array neu gestartet wird, während E/A aktiv ist. Alle E/A zu dem Speicher-Array sollten vor dem Herunterfahren oder Neu starten des Host-Servers oder Speicher-Arrays angehalten werden. Bei einem MD Series-Speicher-Array findet nach der Wiederherstellung eines ausgefallenen Pfades nicht automatisch ein Failback statt, da der Treiber die Geräte ohne einen erzwungenen erneuten Suchlauf nicht automatisch erkennen kann.
13 Konfigurieren von Asymmetric Logical Unit Access Falls Ihr RAID-Speicher-Array der MD Serie asymmetrischen logischen Laufwerkspoolszugriff (Asymmetric Logical Unit Access, ALUA) unterstützt, ermöglicht der aktive-aktive Durchsatz, dass die E/A von einem RAID-Controller-Modul auf ein virtuelles Laufwerk übergeht, die nicht dem RAID-Controller gehört.
Manuelles Hinzufügen einer SATP-Regel in ESXi 5.x So fügen Sie die SATP-Regel in ESXi 5.x manuell hinzu: 1. Führen Sie den folgenden Befehl aus: # esxcli storage nmp satp rule add –s VMW_SATP_ALUA –V DELL –M array_PID -c tpgs_on Wo, array_PID ist Ihre Speicher-Array Modell/Produkt-ID. Um die entsprechende array_PID für Ihr Speicher-Array auszuwählen, siehe die folgende Tabelle. Tabelle 17.
So stellen Sie eine Round-Robin-Richtlinie für den Lastenausgleich auf dem ESXi-basierten Host-Server ein: 1. Führen Sie für ESXi 5.x den folgenden Befehl aus: # esxcli storage nmp satp set --default-psp VMW_PSP_RR --satp VMW_SATP_ALUA/VMW_SATP_LSI 2. Starten Sei den ESX-basierten Host-Server neu.
14 Erweiterungsfunktion – Remote-Replikation Die folgenden Typen von Remote-Replikation werden auf dem MD-Speicherarray unterstrützt: • • Remote-Replikation – Asynchrone Standard-Replikation unter Verwendung von Momentaufnahmen, um den Resychronisierungsvorgang zwischen dem lokalen und Remote-Standort als Stapel zu verarbeiten. Dieser Replikationstyp wird auf sowohl Fibre Channel- als auch iSCSI-Speicherarrays (nicht zwischen) unterstützt.
• Statistik für jedes Replikationspaar. Das Replikation-Repository wird normalerweise automatisch erstellt, wenn Sie ein repliziertes Paar erstellen. Sie können das Repository jedoch auch manuell erstellen.
Anforderungen und Einschränkungen der RemoteReplikation Um die Erweiterungsfunktion „Standard-Remote-Replikation“ zu verwenden, müssen Sie Folgendes aufweisen: • • • • • • • Zwei Speicher-Arrays mit Schreibzugriff, und die beiden Speicher-Arrays müssen über genügend Speicherplatz verfügen, um die Daten zwischen ihnen zu replizieren. Jeder Speicher muss über eine Dual-Controller-Fibre Channel- oder iSCSI-Konfiguration (Einzel-Controller-Konfigurationen werden nicht unterstützt) verfügen.
ANMERKUNG: Führen Sie die folgenden Aktivierungsschritte zuerst auf dem lokalen Speicher-Array durch, und wiederholen Sie sie dann auf dem Remote-Speicher-Array. 1. Klicken Sie im AMW des lokalen Speicher-Arrays auf die Registerkarte Speicher- und Kopierdienste. 2. Wählen Sie Kopierdienste > Remote-Replikation > Aktivieren. 3. Falls die Erweiterungsfunktionen "Remote-Replikation" sowie "Remote-Replikation (Legacy)" auf Ihrem Speicher-Array unterstützt werden, wählen Sie Remote-Replikation aus. 4.
Zweck einer Remote-Replikationsgruppe Bei der Erstellung einer Remote-Replikationsgruppe können alle virtuellen Replikationslaufwerkspaare in der Gruppe als eine einzelne verwaltet werden. Zum Beispiel: alle replizierten virtuellen Laufwerkspaare in einer Gruppe können diesen Einstellungen zur Datensynchronisierung primäre und sekundäre Rollen und Schreibmodi teilen.
Replikationskonfiguration enthalten beide dieser virtuellen Festplatten identische Kopien derselben Daten. Das replizierte Paar ist in der Remote-Replikationsgruppe enthalten, wodurch ermöglicht wird, dass sie zur selben Zeit wie alle anderen replizierten Paare innerhalb derselben Remote-Replikationsgruppe synchronisiert werden. Auf der E/A-Ebene werden Schreibvorgänge zuerst auf dem primären virtuellen Laufwerk und dann auf dem sekundären virtuellen Laufwerk durchgeführt.
ANMERKUNG: Das Replikations-Repository wird normalerweise während der Erstellung des virtuellen Laufwerkspaars automatisch erstellt. Die manuelle Repository-Erstellung wird nur für fortgeschrittene Speicheradministratoren empfohlen, die über eingehende Kenntnisse hinsichtlich der Konsistenz und der optimalen Konfiguration physikalischer Laufwerke verfügen. Die Methode „Automatisch“ wird empfohlen. 6. Klicken Sie auf OK, wenn eine Meldung angezeigt wird, dass das Paar erfolgreich erstellt wurde.
15 Downloads von Verwaltungs-Firmware Themen: • • • • • • • Herunterladen von Paketen für RAID-Controller und NVSRAM Herunterladen von Firmware für RAID-Controller und NVSRAM Herunterladen von NVSRAM-Firmware (ausschließlich) Herunterladen von Firmware für physikalische Laufwerke Herunterladen von EMM-Firmware für Erweiterungsmodule der MD1200-Reihe SMART: Self-Monitoring Analysis and Reporting Technology (Selbstüberwachende Analyse- und Berichterstellungstechnologie) Datenträgerfehler und nicht lesbare Se
ANMERKUNG: Die Bereiche RAID-Controller-Modul-Firmware und „NVSRAM“ führen jeweils die aktuelle Firmware und die aktuellen NVSRAM-Versionen auf. 3. Klicken Sie zum Lokalisieren des Verzeichnisses, in dem die herunterzuladende Datei liegt, neben dem Textfeld Ausgewählte RAIDController-Modul Firmwaredatei auf Datei auswählen. 4. Wählen Sie im Bereich Dateiauswahl die herunterzuladende Datei aus.
ANMERKUNG: Wenn Speicher-Arrays das spätere Herunterladen der Dateien und Aktivieren der Firmware und des NVSRAM nicht unterstützen, wird das Kontrollkästchen Dateien übertragen, aber nicht aktivieren (später aktivieren) deaktiviert. 17. Klicken Sie auf OK. Das Dialogfeld Confirm Download (Download bestätigen) wird angezeigt. 18. Klicken Sie auf Ja.
ANMERKUNG: Wenn Sie ein Speicher-Array auswählen, das nicht aktualisiert werden kann, wird die Schaltfläche „NVSRAM“ deaktiviert. Das Dialogfeld NVSRAM herunterladen wird angezeigt. Es werden die aktuellen Firmware-Versionen und die NVSRAM-Versionen der ausgewählten Speicher-Arrays angezeigt.
1. Wählen Sie im AMW Aktualisieren > Firmware für physikalische Laufwerke. Das Dialogfeld Herunterladevorgang der Firmware für physikalische Laufwerke - Einführung wird angezeigt. 2. Klicken Sie auf Weiter. Das Dialogfenster Firmware für physikalisches Laufwerk herunterladen - Paket hinzufügen wird angezeigt. 3. Klicken Sie im Bereich Selected Packages (Ausgewählte Pakete) auf Add (Hinzufügen). Navigieren Sie zum Speicherort des Paketes und klicken Sie auf OK.
7. Überwachen Sie den Status des Fortschritts und der Vollständigkeit des Herunterladevorgangs auf die Erweiterungsgehäuse. Der Fortschritt und Status jedes Erweiterungsgehäuses, das an dem Herunterladevorgang teilnimmt, wird in der Statusspalte der „Gehäuse auswählen“-Tabelle angezeigt. ANMERKUNG: Jeder Firmware-Herunterladevorgang kann bis zu seinem Abschluss einige Minuten in Anspruch nehmen. 8.
16 Firmwarebestandsliste Ein Speicher-Array besteht aus vielen Komponenten, zu denen RAID-Controller-Module, physikalische Laufwerke und Gehäuseverwaltungsmodule (EMM) gehören können. Jede dieser Komponenten enthält Firmware. Einige Firmware-Versionen sind von anderen Firmware-Versionen abhängig. Informationen zu allen Firmware-Versionen im Speicher-Array finden Sie in der FirmwareBestandsliste.
17 Systemschnittstellen Themen: • • Virtual Disk Service (VDS) Volume Shadow-Copy Service (VSS) Virtual Disk Service (VDS) Der Microsoft Virtual Disk Service (VDS) ist eine Komponente des Windows-Betriebssystems. Die VDS-Komponente nutzt bestimmte Software-Module von Drittanbietern, sogenannte Provider, um Speicherressourcen, wie etwa MD Series Dense-Speicher-Arrays, aufzurufen und zu konfigurieren.
ANMERKUNG: Da die Einstellungen in der grafischen Benutzeroberfläche (GUI) Array-spezifisch und nicht Hostspezifisch sind, werden Sie bei der VSS-Registrierung während des Windows-Setup von der GUI aufgefordert, den Namen des Arrays bereitzustellen. VSS-Hardware-Anbieter Tipps für Speicherverwaltung: • • • Die Anzahl der virtuellen Snapshotlaufwerken, die mithilfe eines einzelnen Snapshot-Satzes erstellt werden können, hängt von der E/A-Belastung auf den RAID-Controller-Modulen ab.
18 Speicher-Array-Software Themen: • • • • • • • • • • • • • • • • Startvorgang Gerätezustand Ablaufverfolgungspuffer Erfassen von Daten zu physikalischen Laufwerken Ereignisprotokoll Recovery Guru Speicher-Array-Profil Anzeigen der physikalischen Zuweisungen Wiederherstellen eines nicht reagierenden Speicher-Arrays Lokalisieren eines physikalischen Laufwerks Lokalisieren eines Erweiterungsgehäuses Aufzeichnen von Zustandsinformationen Dienstprogramm SMrepassist Nicht identifizierte Geräte Wiederherstellen
Aus den in der Tabellenansicht des EMW angezeigten Statussymbolen geht der ausführliche Status aller Komponenten hervor, aus denen das Speicher-Array besteht. Die Option „Recovery Guru“ bietet außerdem eine ausführliche Erläuterung der Betriebszustände und führt die erforderlichen Schritte auf, um den Status „Aufmerksamkeit erforderlich“ zu beheben. Weitere Informationen finden Sie im Recovery Guru.
Tabelle 19. Zusätzliche Statussymbole und Beschreibungen (fortgesetzt) Status Symbol Beschreibung Benachrichtigung eingerichtet Sie können in der Strukturansicht Benachrichtigungen für beliebige Knoten einrichten. Durch das Einrichten einer Benachrichtigung auf einer übergeordneten Knotenebene, z. B. auf einer Host-Ebene, werden auch Benachrichtigungen für alle untergeordneten Knoten eingerichtet.
Tabelle 19. Zusätzliche Statussymbole und Beschreibungen (fortgesetzt) Status Symbol Speicher-Array hinzufügen fehlerhaft Beschreibung Wird nur angezeigt, wenn ein Fehler auftritt. In der Strukturansicht können Symbole als Zeichenkette angezeigt werden, um mehr Informationen übermitteln zu können.
• Um das Dialogfeld zu schließen, klicken Sie auf Abbrechen. Erfassen von Daten zu physikalischen Laufwerken Verwenden Sie die Option Daten des physikalischen Laufwerks sammeln, um Protokolldaten von allen physikalischen Laufwerken in Ihrem Speicher-Array zu sammeln. Protokollabfragedaten bestehen aus statistischen Informationen, die auf jedem der physikalischen Laufwerke in Ihrem Speicher-Array aufbewahrt werden.
2. Wählen Sie auf der Registerkarte Speicher-Arrays ein oder mehrere Speicher-Arrays aus. 3. Führen Sie eine der folgenden Aktionen aus: • Wenn Sie einen Zeitplan zur Supportdatensammlung unterbrechen möchten, klicken Sie auf die Schaltfläche Aufheben und klicken Sie anschließend auf Ja. • Wenn Sie einen Zeitplan zur Supportdatensammlung neu starten möchten, klicken Sie auf die Schaltfläche Wieder aufnehmen und klicken Sie anschließend auf Ja. 4. Klicken Sie auf OK.
Recovery Guru Recovery Guru ist eine Komponente von MD Storage Manager, mit der sich kritische Ereignisse im Speicher-Array diagnostizieren und schrittweise beheben lassen. Um den Recovery-Guru im AMW anzuzeigen, führen Sie einen der folgenden Schritte durch: • • Wählen Sie Monitor > Funktionszustand > Funktionszustand (Recovery Guru) anzeigen. Klicken Sie in der Registerkarte Zusammenfassung auf den Link Speicher-Array erfordert Aufmerksamkeit.
ANMERKUNG: Die Datei wird als ASCII-Textdatei gespeichert. f. Klicken Sie auf Save (Speichern). 6. Um das Speicher-Array-Profil zu schließen, klicken Sie auf Schließen.
13. 14. 15. 16. 17. 18. • ping • ping Wenn die Überprüfung erfolgreich war, gehen Sie zu Schritt 14, ansonsten zu Schritt 15. Entfernen Sie den Host, der den Status „Reagiert nicht“ aufweist, aus dem Enterprise Management-Fenster (EMW), und wählen Sie die Option Speicher-Array hinzufügen aus, um den Host wieder hinzuzufügen. Sollte der Host nicht den Status „Optimal“ aufweisen, fahren Sie mit Schritt 16 fort.
Die LED-Aktivierung ist vom Typ des vorhandenen Erweiterungsgehäuses abhängig. • • Wenn Sie ein Erweiterungsgehäuse mit einer weißen LED haben, führt der Vorgang „Erweiterungsgehäuse blinken" dazu, dass die weiße LED am Erweiterungsgehäuse aufleuchtet. Die LED blinkt nicht. Wenn Sie irgendeinen anderen Erweiterungsgehäusetyp haben, führt dieser Vorgang dazu, dass die entsprechende LED an allen physikalischen Laufwerken im Erweiterungsgehäuse blinkt. Um ein Erweiterungsgehäuse zu lokalisieren: 1.
Navigieren Sie von einem Eingabeaufforderung-Fenster auf einem Windows-Host-Server zu C:\Program Files\Dell\MD Storage Manager\util und führen Sie den folgenden Befehl aus: SMrepassist -f wobei der Parameter -f alle speicherresidenten Daten des durch (Dateisystemkennung) spezifizierten Dateisystems löscht.
e. Vergewissern Sie sich ggf., dass die Host-Bus-Adapter im Host installiert sind. f. Überprüfen Sie alle externen Kabel und Switches, um sicherzugehen, dass keine sichtbaren Schäden vorhanden sind und alle Verbindungen fest sitzen. g. Falls Sie das RAID-Controller-Modul kürzlich ausgetauscht oder hinzugefügt haben, starten Sie die Host-Kontext-Agent-Software neu, damit der neue Controller gefunden wird. Falls ein Problem besteht, nehmen Sie die erforderlichen Änderungen am Host vor. 4.
Starten der SMagent-Software unter Linux Um die Host-Kontext-Agent-Software unter Linux zu starten oder neu zu starten, geben Sie in der Eingabeaufforderung den folgenden Befehl ein: SMagent start Die SMagent-Software wird nun initialisiert. Dies kann einige Zeit dauern. Der Cursor wird währenddessen angezeigt, aber das Terminalfenster reagiert nicht. Beim Start des Programms wird folgende Meldung angezeigt: SMagent started.
19 Wie Sie Hilfe bekommen Themen: • Kontaktaufnahme mit Dell EMC Kontaktaufnahme mit Dell EMC ANMERKUNG: Wenn Sie nicht über eine aktive Internetverbindung verfügen, können Sie Kontaktinformationen auch auf Ihrer Auftragsbestätigung, dem Lieferschein, der Rechnung oder im Dell-Produktkatalog finden. Dell stellt verschiedene onlinebasierte und telefonische Support- und Serviceoptionen bereit.