Dell PowerVault NX3200 用户手册 管制型号: E14S Series 管制类型: E14S001
注、小心和警告 备注: “注”表示可以帮助您更好地使用计算机的重要信息。 小心: “小心”表示可能会损坏硬件或导致数据丢失,并说明如何避免此类问题。 警告: “警告”表示可能会造成财产损失、人身伤害甚至死亡。 © 2012 Dell Inc. 本文中涉及的商标:Dell™、Dell 徽标、Dell Precision™、OptiPlex™、Latitude™、PowerEdge™、PowerVault™、PowerConnect™、 OpenManage™、EqualLogic™、Compellent™、KACE™、FlexAddress™、Force10™ 和 Vostro™ 是 Dell Inc. 的商标。Intel®、Pentium®、 Xeon®、Core® 和 Celeron® 是 Intel Corporation 在美国和其他国家/地区的注册商标。AMD® 是 Advanced Micro Devices, Inc. 的 注册商标,AMD Opteron™、AMD Phenom™ 和 AMD Sempron™ 是 Advanced Micro Devices, Inc.
目录 注、小心和警告...........................................................................................................................2 章 1. 关于系统...............................................................................................................................9 前面板部件和指示灯..............................................................................................................................................9 诊断指示灯.................................................................................
UEFI Boot Menu(UEFI 引导菜单)...............................................................................................................30 嵌入式系统管理....................................................................................................................................................30 iDRAC 设置公用程序.............................................................................................................................................31 进入 iDRAC 设置公用程序............................................
卸下电缆固定支架.........................................................................................................................................53 安装电缆固定支架.........................................................................................................................................54 扩充卡和扩充卡提升板........................................................................................................................................54 扩展卡安装原则............................................................
安装硬盘驱动器背板.....................................................................................................................................83 卸下硬盘驱动器背板(背面).....................................................................................................................84 安装硬盘驱动器背板(背面).....................................................................................................................85 控制面板.................................................................................................
章 6. 跳线和连接器..................................................................................................................105 系统板跳线设置..................................................................................................................................................105 系统板连接器......................................................................................................................................................106 禁用已忘记的密码..........................................................
1 关于系统 前面板部件和指示灯 图 1: 前面板部件和指示灯 项目 指示灯、按钮或连接器 图标 说明 1 诊断指示灯 诊断指示灯亮起以显示错误状态。 2 系统识别按钮 前面板和背面板上的识别按钮可用于定位机架中的特 定系统。当按下其中一个按钮时,后面板上的系统状 态指示灯将闪烁,直至再次按下其中一个按钮为止。 按下可切换系统 ID 的开和关。 如果系统在 POST 过程中停止响应,按住系统 ID 按钮 五秒以上,可进入 BIOS 进程模式。 要重设 iDRAC(如果未在 F2 iDRAC 设置中禁用),请 按住该按钮超过 15 秒。 3 通电指示灯、电源按钮 通电指示灯在系统开机时亮起。电源按钮控制到系统 的电源设备输出。 备注: 对于兼容 ACPI 的操作系统,使用电源按钮 关闭系统可以在系统电源关闭前执行正常有序的 关机操作。 4 NMI 按钮 用于在运行某些操作系统时对软件和设备驱动程序错 误进行故障排除。可以用回形针的末端按压此按钮。 只有获得合格支持人员指导,或者操作系统说明文件 中有相关指示,才可使用此按钮。 5 硬盘驱动器 最多十二个 3.
项目 指示灯、按钮或连接器 8 信息标签 图标 说明 滑出式标签面板让您可以根据需要记录系统信息,如 Service Tag(服务标签)、NIC、MAC 地址等。 诊断指示灯 系统前面板上的诊断指示灯在系统启动时显示错误状态。 备注: 当系统关闭时诊断指示灯不亮。要启动系统,将系统连接至正常工作的电源并按下电源按钮。 下节描述系统状态和与这些指示灯关联的可能的更正措施: 运行状况指示灯 状态 更正措施 如果系统打开并且运行状况良好,指示灯将呈稳定 蓝色亮起。 无需采取措施。 如果系统打开或处于待机状态,指示灯将呈琥珀色 闪烁,表示存在任何错误(例如,风扇或硬盘驱动 器故障) 请参阅“系统事件日志”或系统消息查看此特 定问题。 无效的内存配置可能导致系统启动时停机,并 且无任何视频输出。请参阅获得帮助。 硬盘驱动器指示灯 状态 更正措施 如果硬盘驱动器遇到 错误,指示灯将呈琥 珀色闪烁。 请参阅“系统事件日志”确定有错误的硬盘驱动器。运行相应的联机诊断检 测程序。重新启动系统并运行嵌入式诊断程序 (ePSA)。如果在 RAID 阵列中 配置硬盘驱动器,则重新启动系统并进入主机适配器
温度指示灯 状态 更正措施 请参见获得帮助。 内存指示灯 状态 更正措施 如果发生内存错误,指示灯将 呈琥珀色闪烁。 请参阅系统事件日志或系统消息查看故障内存的位置。重新安装内 存设备。如果问题仍然存在,请参阅获得帮助。 PCIe 指示灯 状态 更正措施 如果 PCIe 卡遇到错误,指示灯将 呈琥珀色闪烁。 重新启动系统。更新 PCIe 卡所需的任何驱动程序。重新安装插 卡。如果问题仍然存在,请参阅获得帮助。 硬盘驱动器指示灯显示方式 图 2: 硬盘驱动器指示灯 1. 硬盘驱动器活动指示灯(绿色) 2.
驱动器状态指示灯显示方式(仅适用于 RAID) 状态 备注: 在系统开机之后所有硬盘驱动器都初始化之前, 驱动器状态指示灯会一直保持熄灭。此时,驱动器不 能进行插入或卸下操作。 呈绿色闪烁,呈琥珀色闪烁,然后熄灭 预测的驱动器故障 每秒呈琥珀色闪烁四次 驱动器故障 呈绿色缓慢闪烁 正在重建驱动器 呈绿色稳定亮起 驱动器联机 呈绿色闪烁三秒钟,呈琥珀色闪烁三秒钟,然后 熄灭六秒钟 已中止重建 背面板部件和指示灯 图 3: 背面板部件和指示灯 项目 指示灯、按钮或连接器 1 系统识别按钮 图标 说明 前面板和背面板上的识别按钮可用于定位机架中的特 定系统。当按下其中一个按钮时,后面板上的系统状 态指示灯将闪烁,直至再次按下其中一个按钮为止。 按下可切换系统 ID 的开和关。 如果系统在 POST 过程中停止响应,按住系统 ID 按钮 五秒以上,可进入 BIOS 进程模式。 要重设 iDRAC(如果未在 F2 iDRAC 设置中禁用),请 按住该按钮并保持 15 秒以上。 2 系统识别连接器 通过可选电缆固定臂连接可选系统状态指示灯部件。 3 iDRAC7 Enter
项目 指示灯、按钮或连接器 8 以太网连接器(4 个) 图标 说明 四个集成的 10/100/1000 Mbps NIC 连接器 或 四个集成连接器包括: • • 9 全高 PCIe 扩展卡插槽(3 个) 10 电源设备 (PSU1) 交流 11 电源设备 (PSU2) 或 两个 10/100/1000 Mbps NIC 连接器 两个 100 Mbps/1 Gbps/10 Gbps SFP+/10 GbE T 连 接器 用于连接多达三个全高 PCI Express 扩展卡。 直流 495 W、750 W 或 1100 W 1100 W(若可用) 12 硬盘驱动器(2 个)(背 面) 最多两个可热插拔的 2.5 英寸硬盘驱动器。 13 vFlash 介质卡插槽 允许您插入 vFlash 介质卡。 NIC 指示灯代码 图 4: NIC 指示灯 1. 链路指示灯 2.
图 5: 交流电源设备状态指示灯 1. 交流电源设备状态指示灯/手柄 图 6: 直流电源设备状态指示灯 1.
电源指示灯 状态 显示方式 小心: 不支持配合使用交流和直流电源设备,并且这种混合会触发不匹配情况。 绿色闪烁 在热添加电源设备时,这表示电源设备与其它电源设备(在效率、功能组、运行状况和支持的 电压方面)不匹配。请使用与其它已安装电源设备容量匹配的电源设备来更换指示灯闪烁的电 源设备。 可能需要的其它信息 警告: 请参阅您的系统随附的安全和管制信息。保修信息可能包含在此说明文件中,也可能作为单独的说 明文件提供。 • • • • 入门指南提供系统设置和技术规格的概览。本说明文件可在 support.dell.com/manuals 上在线查看。 机架解决方案附带的机架说明文件,介绍了如何将系统安装到机架中(如果需要)。 系统随附的任何介质提供了用于配置和管理系统的说明文件和工具,包括与操作系统、系统管理软 件、系统更新软件以及随系统购买的系统组件相关的文件和工具。 有关本说明文件中所用缩略语或缩写词的全称,请参阅 support.dell.com/manuals 上的“词汇表”。 备注: 请定期访问 support.dell.
使用系统设置程序和引导管理器 2 借助系统设置程序可以管理系统硬件和指定 BIOS 级选项。 在启动期间可以使用下列击键访问系统功能: 击键 说明 进入系统设置程序。 进入将打开 Dell Lifecycle Controller 2 (LC2) 的系统服务。Dell LC2 使用图形用户界面支持系统管理功能, 如操作系统部署、硬件诊断、平台更新以及平台配置。准确的 LC2 功能组由购买的 iDRAC 许可证决 定。有关详情,请参阅 Dell LC2 说明文件。 进入 BIOS 引导管理器或统一可扩展固件接口 (UEFI) 引导管理器,具体视系统的引导配置而定。 启动预引导执行环境 (PXE) 引导。 通过系统设置程序,您可以: • 在添加或删除硬件后更改 NVRAM 设置 • 查看系统硬件配置 • 启用或禁用集成设备 • 设置性能和电源管理阈值 • 管理系统安全 可使用以下工具访问系统设置程序: • 标准图形浏览器,默认启用 • 文本浏览器,使用 Console Redirection(控制台重定向)启用 要启用 Consol
备注: 操作系统必须与 UEFI 兼容才能从 UEFI 引导模式安装。DOS 和 32 位操作系统不支持 UEFI,只能通过 BIOS 引导模式进行安装。 备注: 有关支持的操作系统的最新信息,请访问 dell.com/ossupport。 进入系统设置程序 1. 打开或重新启动系统。 2.
菜单项 说明 Device Settings(设备设置) 此选项用于查看和配置设备设置。 System BIOS(系统 BIOS)屏幕 备注: 系统设置的选项会基于系统配置发生变化。 备注: 在以下几节中,系统设置的默认设置将在各自选项下列出(如果有)。 菜单项 说明 System Information(系统信息) 显示有关系统的信息,如系统型号名称、BIOS 版本、服务标签等。 Memory Settings(内存设置) 显示与所安装内存有关的信息和选项。 Processor Settings(处理器设 置) 显示与处理器有关的信息和选项,如速度、高速缓存大小等。 Boot Settings(引导设置) 显示各选项以指定引导模式(BIOS 或 UEFI)。可让您修改 UEFI 和 BIOS 引 导设置。 Integrated Devices(集成设备) 显示各选项以启用或禁用集成设备控制器和端口,以及指定相关的功能和 选项。 Serial Communication(串行通 信) 显示各选项以启用或禁用串行端口以及指定相关功能和选项。 System Profile Se
Memory Settings(内存设置)屏幕 菜单项 说明 System Memory Size(系统 内存大小) 显示系统中安装的内存容量。 System Memory Type(系统 内存类型) 显示系统中安装的内存类型。 System Memory Speed(系统 显示系统内存速度。 内存速度) System Memory Voltage(系 统内存电压) 显示系统内存速度。 Video Memory(视频内存) 显示视频内存容量。 System Memory Testing(系 统内存检测) 指定系统内存检测是否在系统引导期间运行。选项包括 Enabled(已启用)和 Disabled(已禁用)。默认情况下,System Memory Testing(系统内存检测)选 项设置为 Disabled(已禁用)。 Memory Operating Mode(内 指定内存运行模式。取决于系统内存配置的可用选项为 Optimizer Mode(优化 存运行模式) 器模式)、Advanced ECC Mode(高级 ECC 模式)、Mirror Mode(镜像模 式)、Spare Mo
菜单项 说明 Alternate RTID (Requestor Transaction ID) Setting(备用 RTID [请求程序交易 ID] 设 置) 允许您对远程插槽分配多个 RTID,以便改进插槽间的高速缓存性能,或使 NUMA 在正常模式下操作。默认情况下,Alternate RTID (Requestor Transaction ID) Setting(备用 RTID [请求程序交易 ID] 设置)设置为 Disabled(已禁用)。 Virtualization Technology(虚 拟化技术) 允许您启用或禁用为虚拟化提供的其它硬件功能。默认情况下,Virtualization Technology(虚拟化技术)选项设置为 Enabled(已启用)。 Adjacent Cache Line Prefetch (相邻的高速缓存行预先访 存) 允许您最优化系统需要顺序内存访问高利用率的应用程序。默认情况下, Adjacent Cache Line Prefetch(相邻的高速缓存行预先访存)选项设置为 Enabled(已启用)。可对需要随机内存访问高利用率的应用程序禁用此
SATA Settings(SATA 设置)屏幕 菜单项 说明 Embedded SATA(嵌入 式 SATA) 允许将嵌入式 SATA 设置为 Off(关)、ATA、AHCI 或 RAID 模式。默认情况下, Embedded SATA(嵌入式 SATA)设置为 AHCI Mode(AHCI 模式)。 Port A(端口 A) Auto(自动)为连接至 SATA 端口 A 的设备启用 BIOS 支持。默认情况下,端口 A 设 置为 Auto(自动)。 Port B(端口 B) Auto(自动)为连接至 SATA 端口 B 的设备启用 BIOS 支持。默认情况下,端口 B 设 置为 Auto(自动)。 Port C(端口 C) Auto(自动)为连接至 SATA 端口 C 的设备启用 BIOS 支持。默认情况下,端口 C 设 置为 Auto(自动)。 Port D(端口 D) Auto(自动)为连接至 SATA 端口 D 的设备启用 BIOS 支持。默认情况下,端口 D 设 置为 Auto(自动)。 Port E(端口 E) Auto(自动)为连接至 SATA 端口 E 的设备启用
Integrated Devices(集成设备)屏幕 菜单项 说明 Integrated RAID Controller(集成 RAID 控制器) 允许您启用或禁用集成 RAID 控制器。默认情况下,Integrated RAID Controller(集成 RAID 控制器)选项设置为 Enabled(已启用)。 User Accessible USB Ports(用户可访问的 USB 端口) 允许您启用或禁用用户可访问的 USB 端口。选择 Only Back Ports On(仅启用后面的 端口)可禁用前面的 USB 端口,选择 All Ports Off(关闭所有端口)将禁用前面和后 面的 USB 端口。默认情况下,User Accessible USB Ports(用户可访问的 USB 端口) 选项设置为 All Ports On(打开所有端口)。 Internal USB Port(内部 USB 端口) 允许您启用或禁用内部 USB 端口。默认情况下,Internal USB Port(内部 USB 端 口)选项设置为 On(开)。 Internal SD Card Port (内
Serial Communications(串行通信)屏幕 菜单项 说明 Serial Communication (串行通信) 可让您在 BIOS 中选择串行通信设备(串行设备 1 和串行设备 2)。也可以启用 BIOS 控制台重定向,并可指定使用的端口地址。默认情况下,Serial Communication(串 行通信)选项设置为 On without Console Redirection(开,未启用控制台重定向)。 Serial Port Address(串 行端口地址) 允许您设置串行设备的端口地址。默认情况下,Serial Port Address(串行端口地 址)选项设置为 Serial Device 1=COM2, Serial Device 2=COM1(串行设备 1=COM2,串 行设备 2=COM1)。 备注: 只能将串行设备 2 用于 LAN 上串行 (SOL)。要使用通过 SOL 的控制台重定 向,请为控制台重定向和串行设备配置相同的端口地址。 External Serial Connector 可让您将外部串行连接器与串行设备 1、串行设备 2 或远程访问设备关联。默
菜单项 说明 C1E 允许您在处理器处于闲置状态时启用或禁用处理器切换至最低性能状态。默认情况 下,C1E 选项设置为 Enabled(已启用)。 C States(C 状态) 允许您启用或禁用处理器在所有可用电源状态下运行。默认情况下,C States(C 状 态)选项设置为 Enabled(已启用)。 显示器/Mwait 可让您启用处理器中的 Monitor/Mwait(显示器/Mwait)说明。默认情况下,Monitor/ Mwait(显示器/Mwait)选项针对所有系统配置文件设置为 Enabled(启用),Custom (自定义)除外。 备注: 此选项仅可在禁用 Custom(自定义)模式下的 C States(C 状态)选项时才 禁用。 备注: 当 C States(C 状态)在 Custom(自定义)模式下启用时,更改 Monitor/ Mwait(显示器/Mwait)设置不会影响系统功率/性能。 Memory Patrol Scrub (内存轮巡检查) 允许您设置内存轮巡检查频率。默认情况下,Memory Patrol Scrub(内存轮巡检查) 选项设置为 Standard
菜单项 说明 TPM Clear(TPM 清 除) 小心: 清除 TPM 会导致 TPM 中的所有密钥丢失。丢失 TPM 密钥可能对引导至操作 系统产生影响。 允许您清除 TPM 的所有内容。默认情况下,TPM Clear(TPM 清除)选项设置为 No (无)。 Intel TXT 允许您启用或禁用 Intel Trusted Execution Technology(Intel 受信任的执行技术)。要启 用 Intel TXT,必须启用 Virtualization Technology(虚拟化技术),并且必须启用 TPM Security(TPM 安全保护)的 Pre-boot measurements(预引导测量)。默认情况下, Intel TXT 选项设置为 Off(关闭)。 BIOS Update Control (BIOS 更新控制) 允许您使用基于 DOS 或 UEFI shell 的 快擦写公用程序更新 BIOS。对于不需要本地 BIOS 更新的环境,建议将此字段设置为 Disabled(禁用)。默认情况下,BIOS Update Control(BIOS 更新控制)选项设置为
菜单项 说明 In-System Characterization(系统 此字段用于启用或禁用 In-System Characterization(系统内特性)。默认情 内特性) 况下,In-System Characterization(系统内特性)设置为 Enabled(已启 用)。 系统密码和设置密码功能 可创建系统密码和设置密码来保护您的系统安全。要启用系统密码和设置密码创建,密码跳线必须设置为已启 用。有关密码跳线设置的详情,请参阅“系统板跳线设置”。 系统密码 必须输入此密码才能登录系统。 设置密码 必须输入此密码才能访问并更改系统的 BIOS 或 UEFI 设置。 小心: 密码功能为系统中的数据提供了基本的安全保护。 小心: 只要系统在运行且无人值守,任何人均可访问系统上存储的数据。 备注: 您的系统出厂时已禁用系统密码和设置密码功能。 设定系统密码和/或设置密码 备注: 密码跳线用于启用或禁用系统密码和设置密码功能。有关密码跳线设置的详情,请参阅“系统板跳 线设置”。 仅当密码跳线设置已启用且 Password Status(密码状态)为 Unlocked(已解除锁定)时,才
6. 重新输入先前输入的系统密码,然后单击 OK(确定)。 7. 选择 Setup Password(设置密码),输入系统密码,然后按 或 。 将出现一则信息,提示您重新输入设置密码。 8. 重新输入先前输入的设置密码,然后单击 OK(确定)。 9. 按 键可返回到系统 BIOS 屏幕。再按一次 键,将出现提示您保存更改的信息。 备注: 重新引导系统之后,密码保护才能生效。 删除或更改现有系统密码和/或设置密码 确保在尝试删除或更改现有系统密码和/或设置密码之前 Password(密码)跳线设置为 Enabled(已启用)并且 Password Status(密码状态)为 Unlocked(已解除锁定)。如果 Password Status(密码状态)为 Locked(已锁 定),则不能删除或更改现有系统密码和/或设置密码。 删除或更改现有系统和/或设置密码: 1. 要进入系统设置程序,开机或重新引导后立即按 。 2.
在已启用设置密码的情况下进行操作 如果将 Setup Password(设置密码)设置为 Enabled(已启用),则必须输入正确的设置密码才能修改大部分 的系统设置选项。 如果您尝试输入三次密码,但均不正确,系统会显示以下信息 Invalid Password! Number of unsuccessful password attempts: System Halted! Must power down.
键 说明 显示系统设置程序的帮助文件。 备注: 对于大多数选项,您所做的任何更改都将被记录下来,但要等到重新启动系统后才能生效。 Boot Manager(引导管理器)屏幕 菜单项 说明 Continue Normal Boot(持续 系统尝试从引导顺序中的第一项开始引导至设备。如果引导尝试失败,系统将 正常引导) 继续从引导顺序中的下一项进行引导,直到引导成功或者找不到引导选项为 止。 BIOS Boot Menu(BIOS 引导 显示可用 BIOS 引导选项(标有星号)的列表。选择想要使用的引导选项并按 菜单) Enter 键。 UEFI Boot Menu(UEFI 引导 菜单) 显示可用 UEFI 引导选项(标有星号)的列表。选择想要使用的引导选项并按 Enter 键。UEFI Boot Menu(UEFI 引导菜单)可让您 Add Boot Option(添加引导选 项)、Delete Boot Option(删除引导选项)或 Boot From File(从文件引导)。 Driver Health Menu(驱动程 显示系统上安装的驱动程序列表及其运行状况。 序运行状况
iDRAC 设置公用程序 iDRAC 设置公用程序是使用 UEFI 设置和配置 iDRAC 参数的接口。可使用 iDRAC 设置公用程序启用或禁用各种 iDRAC 参数。 备注: 访问 iDRAC 设置公用程序上的某些功能需要升级 iDRAC7 Enterprise 许可证。 有关使用 iDRAC 的详情,请参阅 support.dell.com/manuals 上软件 → 系统管理 → Dell 远程访问控制器下的 iDRAC7 用户指南。 进入 iDRAC 设置公用程序 1. 开启或重新启动受管系统。 2. 开机自测 (POST) 期间按 。 3.
安装系统组件 3 建议工具 要执行本节中的步骤,可能需要使用以下工具: • 系统键锁的钥匙 • 2 号梅花槽螺丝刀 • T10 和 T15 Torx 螺丝刀 • 接地腕带 制作直流电源设备 (PSU) 的电缆(如果可用)需要以下工具: • AMP 90871-1 手动压接工具或同类产品 • 可以除去尺寸为 10 AWG 的绝缘的实芯或绞合铜电线的绝缘层的剥线钳 备注: 使用 alpha 电线部件号 3080 或同类产品(65/30 绞合)。 前挡板(可选) 卸下前挡板 1. 打开挡板左端的钥匙锁。 2. 提起钥匙锁旁的释放闩锁。 3. 旋转挡板的左端,使其脱离前面板。 4.
1. 2. 3. 4. 释放闩锁 钥匙锁 前挡板 锁定挂钩 安装前挡板 1. 用挂钩将挡板右端和机箱连在一起。 2. 将挡板未固定的一端安装到系统上。 3. 使用锁扣固定挡板。 打开与合上系统护盖 警告: 每当您需要抬起系统时,请让他人协助您。为避免伤害,请勿试图一个人抬起系统。 警告: 系统处于运行状态时打开或卸下系统护盖会使您有触电的风险。 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 不要操作没有护盖的系统超过五分钟。 打开系统护盖 备注: 拆装系统内部组件时,建议始终使用防静电垫和防静电腕带。 1. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 2. 逆时针旋转闩锁释放锁,直至解除锁定的位置。 3. 向上提起系统顶部的闩锁并向后滑动护盖。 4.
图 8: 打开与合上系统护盖 1. 系统护盖 2. 闩锁 3. 闩锁释放锁 合上系统护盖 1. 向上提起系统护盖上的闩锁。 2. 将护盖置于机箱顶部稍稍往后的位置,使其错开机箱挂钩并平躺在机箱上。 3. 向下推闩锁以使护盖合上。 4. 将闩锁释放锁顺时针旋转,以固定机盖。 5.
图 9: 系统内部 1. 2. 3. 4. 5. 6. 7. 8. 冷却风扇部件 电缆固定支架 冷却导流罩 硬盘驱动器背板(背面) vFlash 介质插槽 硬盘驱动器(背面)(2 个) 扩展卡提升板 3 网络子卡 9. 10. 11. 12. 13. 14. 扩展卡提升板 2 扩展卡提升板 1 处理器 1 的散热器 处理器 2 的散热片 DIMM 冷却风扇(6 个) 冷却导流罩 卸下冷却导流罩 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 绝对不要在冷却罩被移除的情况下操作系统。系统有可能会迅速过热,造成系统关闭和数据丢失。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3.
4. 手握触点,将导流罩提起,使其脱离系统。 图 10: 卸下和安装冷却导流罩 1. 冷却导流罩 2. 支持全长 PCIe 卡 安装冷却导流罩 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 若要在机箱中正确安装冷却导流罩,请确保系统内的电缆沿机箱壁布设并使用电缆固定支架固定。 1. 将冷却导流罩上的卡舌对准机箱上的固定插槽。 2. 将冷却导流罩向下放到机箱中,直到它稳固就位。 3. 如果适用,请更换全长 PCIe 卡。 4. 合上系统护盖。 5.
• 每个通道填充的 DIMM 数目 • DIMM 操作电压 • 所选的系统配置文件(例如,Performance Optimized [性能优化]、Custom [自定义] 或 Dense Configuration Optimized [密集配置优化]) • 最大受支持的处理器 DIMM 频率 系统包含 24 个内存插槽,分为两组(每组 12 个),每个处理器一组。每组的 12 个插槽分入四个通道。在每个 通道中,第一个插槽的释放拉杆标为白色,第二个插槽的标为黑色,第三个插槽的标为绿色。 备注: 插槽 A1 至 A12 中的 DIMM 分配给处理器 1,插槽 B1 至 B12 中的 DIMM 分配给处理器 2。 图 11: 内存插槽位置 内存通道按如下方式组织: 处理器 1 38 通道 0:插槽 A1、A5 和 A9
通道 1:插槽 A2、A6 和 A10 通道 2:插槽 A3、A7 和 A11 通道 3:插槽 A4、A8 和 A12 处理器 2 通道 0:插槽 B1、B5 和 B9 通道 1:插槽 B2、B6 和 B10 通道 2:插槽 B3、B7 和 B11 通道 3:插槽 B4、B8 和 B12 下表显示支持配置的内存数和操作频率。 DIMM 类型 填充的 DIMM 数/ 通道 操作频率 (MT/s) 1.5 V 最大 DIMM 列数/通道 1.
• 按以下顺序按最高列数填充插槽 — 首先填充具有白色释放拉杆的插槽,再填充具有黑色释放拉杆的插 槽,最后填充具有绿色释放拉杆的插槽。例如,如果要混用四列和双列 DIMM,则填充具有白色释放卡 舌的插槽中的四列 DIMM,再填充具有黑色释放卡舌的插槽中的双列 DIMM。 • 在双处理器配置中,每个处理器的内存配置应该相同。例如,如果填充处理器 1 的插槽 A1,则填充处 理器 2 的插槽 B1,以此类推。 • 如果遵循其它内存安装规则,则不同大小的内存模块可以混用(例如,2 GB 和 4 GB 内存模块可以混 用)。 • 每个处理器一次填充四个 DIMM(每个通道一个 DIMM)以最大化性能。 • 如果安装不同速度的内存模块,它们将以最低或较低安装内存模块速度运行(具体取决于系统 DIMM 配置)。 模式特定原则 每个处理器均分配有四个内存通道。所选的内存模式将决定允许的配置。 备注: 如果支持 RAS 功能,基于 x4 和 x8 DRAM 的 DIMM 可以混用。但是,必须遵循特定 RAS 功能的所有 原则。基于 X4 DRAM 的 DIMM 在内存优化(独立通道)模式下保留单设备数据校
• 所有内存模块在大小、速度和技术上必须相同。 • 带有白色释放卡舌的内存插槽中安装的 DIMM 必须相同,类似规则适用于带黑色和绿色释放卡舌的插 槽。这可确保相同 DIMM 以匹配对安装 - 例如,A1 与 A2、A3 与 A4、A5 与 A6 等。 内存配置示例 下表显示符合本节中所述的相应内存原则的一个和两个处理器配置的内存配置示例。 备注: 不支持 16 GB 四列 RDIMM。 备注: 下表中的 1R、2R 和 4R 分别表示单列、双列和四列 DIMM。 表.
DIMM 大小 DIMM 数量 (以 GB 为单 位) 系统容量(以 GB 为单位) DIMM 列、组织和频率 DIMM 插槽数 备注: 16 GB DIMM 必须安装在编 号为 A1、A2、A3、A4、A5、 A6、A7 和 A8 的插槽中,8 GB DIMM 必须安装在插槽 A9 和 A11 中。 384 32 12 LRDIMM,x4,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A12 表.
系统容量 DIMM 大小(以 DIMM 数量 (以 GB 为单 GB 为单位) 位) DIMM 列、组织和频率 DIMM 插槽数 备注: 16 GB DIMM 必须安装在 编号为 A1、A2、A3、A4、 B1、B2、B3 和 B4 的插槽中, 8 GB DIMM 必须安装在插槽 A5、A6、B5 和 B6 中。 8 24 2R,x4,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A12 B1、B2、B3、B4、B5、B6、B7、 B8、B9、B10、B11、B12 16 12 2R,x4,1333 MT/s, 2R,x4,1600 MT/s A1、A2、A3、A4、A5、A6 B1、B2、B3、B4、B5、B6 256 16 16 2R,x4,1333 MT/s, 2R,x4,1600 MT/s, A1、A2、A3、A4、A5、A6、A7、 A8 B1、B2、B3、B4、B5、B6、B7、 B8 384 16 24 2R,x4,1333 MT/s A1、A2、A3、A4、A5、A6、A7、 A8、A9、A10、A11、A1
小心: 仅抓住内存模块卡的两边,确保不要触碰内存模块中间。 5. 向下并向外按压插槽两端的弹出卡舌,直至内存模块从插槽中弹出。 图 12: 卸下和安装内存模块 1. 内存模块 2. 内存模块插槽弹出卡舌(2 个) 3. 定位卡锁 6. 在空内存模块插槽中安装内存模块挡片,确保系统充分冷却。 7. 安装冷却导流罩。 8. 合上系统护盖。 9. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 安装内存模块 警告: 在系统关机后一定时间内,内存模块会很烫手。请让它冷却下来后再进行操作。仅抓住内存模块的 两边,避免接触内存模块上的其它组件。 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 为保证系统散热正常,对于任何空置的内存槽,都要安装内存模块填充件。只在您需要在这些内存 槽中安装内存模块时才卸下这些填充件。 1.
备注: 保留卸下的内存模块挡片以备将来使用。 小心: 仅抓住内存模块卡的两边,确保不要触碰内存模块中间。 6. 将内存模块的边缘连接器与内存模块插槽的定位卡锁对准,并将内存模块插入插槽。 备注: 内存模块插槽有定位卡锁,使内存模块只能从一个方向安装到插槽中。 7. 使用大拇指向下按压内存模块,直至插槽拉杆闩锁锁定到位。 8. 如果内存模块已在插槽中正确就位,则内存模块插槽上的拉杆应与已安装内存模块的其它插槽上的拉杆对 准。 重复此过程的步骤 4 至步骤 7 以安装其余的内存模块。 9. 装回冷却导流罩。 10. 合上系统护盖。 11. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 12. 按 进入系统设置程序并检查内存设置。 系统应该已经更改了该值,以反映新安装的内存。 13. 如果值不正确,则可能有一个或多个内存模块未正确安装。请重复此过程的步骤 4 到步骤 7,检查以确保 内存模块已在其插槽中稳固就位。 14.
向外推拉硬盘驱动器挡片,直至其脱离硬盘驱动器插槽。 图 13: 卸下和安装 2.5 英寸硬盘驱动器挡片(背面) 1. 硬盘驱动器挡片(背面) 安装 2.5 英寸硬盘驱动器挡片(背面) 将硬盘驱动器挡片插入硬盘驱动器插槽,直至其卡入到位。 卸下 3.5 英寸硬盘驱动器挡片 小心: 为了维持正常的系统冷却,所有闲置的硬盘驱动器插槽必须安装驱动器挡片。 1. 如果已安装前挡板,请将其卸下。 2. 握住硬盘驱动器挡片前部,按下释放按钮并向外滑动挡片,直至其脱离驱动器插槽。 图 14: 卸下和安装 3.5 英寸硬盘驱动器挡片 1. 硬盘驱动器挡片 2.
安装 3.5 英寸硬盘驱动器挡片 1. 如果已安装前挡板,请将其卸下。 2. 将硬盘驱动器挡片插入硬盘驱动器插槽,直至释放按钮卡入到位。 3. 如果有,请安装前挡板。 卸下热置换硬盘驱动器 小心: 为了防止数据丢失,请确保操作系统支持热交换驱动器安装。请参照操作系统随附的说明文件。 1. 通过管理软件准备要卸下的硬盘驱动器。等待硬盘驱动器托盘上的指示灯发出信号,表示可以安全地卸下 硬盘驱动器。有关详情,请参阅存储控制器的说明文件。 如果硬盘驱动器在线上,绿色活动/故障指示灯会在驱动器关闭时闪烁。当硬盘驱动器指示灯熄灭时,此 时可以卸下硬盘驱动器。 2. 按下释放按钮以打开硬盘驱动器托盘释放手柄。 3. 向外滑动硬盘驱动器托盘,直至其脱离硬盘驱动器插槽。 小心: 为了维持正常的系统冷却,所有闲置的硬盘驱动器插槽必须安装硬盘驱动器挡片。 4. 将硬盘驱动器挡片插入空硬盘驱动器插槽中。 图 15: 卸下和安装热置换硬盘驱动器 1. 释放按钮 2. 硬盘驱动器 3.
小心: 只能使用经检测和认证可用于硬盘驱动器背板的硬盘驱动器。 小心: 不支持在相同的 RAID 卷中混合使用 SAS 和 SATA 硬盘驱动器。 小心: 安装硬盘驱动器时,确保相邻的硬盘驱动器已安全安装。插入硬盘驱动器托盘,尝试锁定已部分安 装托盘旁边的手柄可能损坏部分安装的托盘保护弹簧并使其无法使用。 小心: 为了防止数据丢失,请确保操作系统支持热交换驱动器安装。请参照操作系统随附的说明文件。 小心: 在安装了替换的热置换硬盘驱动器,并且系统开机之后,硬盘驱动器会自动开始重建。必须确保替 换的硬盘驱动器是空白的或包含您想覆盖的数据。替换的硬盘驱动器安装之后,上面的数据会立即丢 失。 1. 如果已在硬盘驱动器插槽中安装硬盘驱动器挡片,请将其卸下。 2. 在硬盘驱动器托盘中安装硬盘驱动器。 3. 按下硬盘驱动器托盘正面的释放按钮,打开硬盘驱动器手柄。 4. 将硬盘驱动器托盘插入硬盘驱动器插槽,直到托盘与背板连接。 5.
图 16: 卸下和安装冷却风扇 1. 2. 3. 4. 冷却风扇部件 风扇释放卡舌 冷却风扇(6 个) 冷却风扇连接器(6 个) 安装冷却风扇 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 打开系统护盖。 2. 将冷却风扇基座上的插头与系统板上的连接器对齐。 3. 将冷却风扇滑入固定插槽,直至卡舌卡入到位。 4. 合上系统护盖。 卸下冷却风扇部件 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 向上旋转蓝色释放拉杆,从机箱解除对冷却风扇部件的锁定。 4.
图 17: 卸下和安装冷却风扇部件 1. 2. 3. 4. 5. 冷却风扇部件 冷却风扇(6 个) 蓝色释放拉杆(2 个) 导向销(2 个) 冷却风扇连接器(6 个) 安装冷却风扇部件 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 确保在安装冷却风扇部件前已正确安装电缆并使用电缆固定支架进行固定。错误安装电缆可能会损 坏电缆。 1. 将冷却风扇部件插槽与机箱上的导向销对齐。 2. 将冷却风扇部件滑入机箱。 3. 向下旋转蓝色释放拉杆直至其稳定就位,将冷却风扇部件卡入机箱。 4. 合上系统护盖。 5.
要从 USB 闪存盘引导,必须为 USB 闪存盘配置一个引导映像,然后在系统设置程序的引导顺序中指定 USB 闪 存盘。 备注: 要查找系统板上的内部 USB 连接器 (J_USB_INT),请参阅“系统板连接器”。 更换内部 USB 闪存盘 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 在系统板上找到 USB 连接器/USB 闪存盘。 要找到 USB 连接器 (J_USB_INT),请参阅“系统板连接器”。 4. 如果已安装 USB 闪存盘,则将其卸下。 5. 将 USB 闪存盘插入到 USB 连接器中。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并开启系统和所有连接的外围设备。 8.
1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下全长 PCIe 卡(如果已安装)。 4. 按下释放卡舌和触点,使 PCIe 卡固定器从机箱上松开。 5. 从机箱中取出 PCIe 卡固定器。 备注: 为确保正常的系统冷却,必须装回 PCIe 卡固定器。 图 19: 卸下和安装 PCIe 卡固定器 1. PCIe 卡固定器 2. 释放卡舌 安装 PCIe 卡固定器 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 请勿使用未安装 PCIe 卡固定器的系统。必须安装 PCIe 卡固定器才能确保正常的系统冷却。 1. 关闭系统和所有连接的外围设备,并断开系统与其电源插座的连接。 2. 打开系统护盖。 3. 将 PCIe 卡袋与机箱上的凸点对齐,将其往下按直至稳固就位。 4. 如果有,请装回全长 PCIe 卡。 5.
打开和关闭 PCIe 卡固定器闩锁 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 要打开 PCIe 卡固定器闩锁,请按压卡舌。 4. 要关闭 PCIe 卡固定器闩锁,请逆时针旋转该闩锁直到其锁定。 备注: 在安装全长 PCIe 卡之前,必须先关闭 PCIe 卡固定器闩锁。安装该全长 PCIe 卡时,打开 PCIe 卡固定 器闩锁。在卸下该全长 PCIe 卡之前必须先关闭 PCIe 卡固定器闩锁。 图 20: 打开和关闭 PCIe 卡固定器闩锁 1. PCIe 卡固定器 2. 卡舌 3. PCIe 卡固定器闩锁 5. 合上系统护盖。 6.
6. 将电缆固定支架从相箱中取出。 图 21: 卸下和安装电缆固定支架 1. 定位插销(2 个) 2. 卡舌 3. 电缆固定支架 安装电缆固定支架 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与其电源插座的连接。 2. 打开系统护盖。 3. 使用定位插销作为导轨,沿相箱壁滑动电缆固定支架,直至卡舌卡入到位。 4. 将所有电缆连接到电缆固定支架中。 5. 安装冷却导流罩。 6. 合上系统护盖。 7.
表. 3: 支持的扩展卡 提升板 PCIe 插槽 处理器连接 高度 长度 链路宽度 插槽宽度 1 1 处理器 2 薄型 半长 x8 x16 1 2 处理器 2 薄型 半长 x8 x16 1 3 处理器 2 薄型 半长 x8 x16 2 4 处理器 2 标准高度 全长 x16 x16 2 5 处理器 1 标准高度 全长 x8 x16 3(备用) 6 处理器 1 标准高度 全长 x16 x16 备注: 要使用提升板上的 PCIe 插槽 1 至 4,必须安装两个处理器。 备注: 扩展卡插槽不能热插拔。 下表提供安装扩展卡的指南,以确保冷却和机械装置装配正确。必须按照所示的插槽优先级,首先安装具有最 高优先级的扩展卡。必须按照插卡优先级和插槽优先级顺序安装所有其它扩展卡。 表.
3. 断开所有与扩充卡相连的电缆。 4. 从插槽中提出扩充卡闩锁。 5. 抓住扩充卡的边缘,小心地将其从扩充卡连接器中卸下。 6. 如果您永久性地卸除扩充卡,请在闲置的扩充槽开口处安装金属填充支架并合上扩充卡闩锁。 备注: 您必须在空置的扩展槽中安装一个填充架以使系统符合联邦通讯委员会 (FCC) 认证。这些填充架也 能将灰尘挡在系统以外,同时有助于系统内的正确通风散热。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 图 22: 卸下和安装扩充卡 1. 2. 3. 4. 5.
将扩充卡安装到扩充卡提升板 2 或 3 中 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 打开扩充卡的包装并准备安装。 有关说明,请参阅扩充卡附带的说明文件。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4. 提起扩充卡闩锁,卸下填充挡片。 5. 握住卡的边缘,调整卡的位置,使扩充卡上的连接器与提升板上的扩充卡连接器对齐。 6. 将卡式边缘连接器稳固地插入扩充卡连接器,直至扩充卡完全就位。 7. 装回扩充卡闩锁。 8. 要安装全长插卡,请使用冷却导流罩上的支撑。 9. 如果适用,用电缆连接至扩充卡。 备注: 在提升板 2 或提升板 3(默认)上安装 GPU 卡时,将 GPU 卡电源电缆连接至提升板上的电源连接 器。 10. 合上系统护盖。 11. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 12.
图 23: 卸下和安装扩充卡提升板 1 1. 2. 3. 4. 扩充卡提升板 1 固定框架 扩充卡连接器 扩充卡 扩充卡闩锁(2 个) 将扩充卡安装到扩充卡提升板 1 中 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 仅在安装两个处理器时才可使用扩充卡提升板 1。 1. 打开扩充卡的包装并准备安装。 有关说明,请参阅扩充卡附带的说明文件。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4. 卸下扩充卡提升板。 5. 按卡舌 A 并逆时针旋转闩锁。 6. 按卡舌 B 并向下旋转闩锁。 7. 握住卡的边缘,调整卡的位置,从而使卡式边缘连接器对准扩充卡连接器。 8. 将卡式边缘连接器稳固地插入扩充卡连接器,直至插卡完全就位。 9. 关闭扩充卡闩锁。 10.
11. 安装扩充卡提升板。 12. 合上系统护盖。 13. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 14. 按照插卡说明文件中的说明,安装插卡所需的任何设备驱动程序。 卸下扩充卡提升板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 仅在安装两个处理器时才可使用扩充卡提升板 1。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 手握触点,将扩充卡提升板从系统板上的提升板连接器上提起。 图 24: 卸下和安装扩充卡提升板 1 1. 2. 3. 4. 扩充卡提升板 1 固定框架 扩充卡提升板 1 提升板导向器-背面(右) 提升板导向器-背面(左) 5. 扩充卡提升板 1 连接器 6.
图 25: 识别扩充卡提升板 1 上的连接器 1. 扩充卡插槽 1 2. 扩充卡插槽 2 3. 扩充卡插槽 3 图 26: 卸下和安装扩充卡提升板 2 1. 2. 3. 4. 5.
图 27: 识别扩充卡提升板 2 上的连接器 1. 2. 3. 4. 机箱防盗开关 扩充卡插槽 4 扩充卡插槽 5 电源连接器(用于 GPU 卡) 图 28: 卸下和安装扩充卡提升板 3 1. 2. 3. 4. 5.
图 29: 识别扩充卡提升板 3 上的连接器 1. 扩充卡插槽 6 2. 扩充卡插槽 7 3. 电源连接器(用于 GPU 卡) 4. 卸下或安装提升板上的扩充卡(如果适用)。 5. 装回扩充卡提升板。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 安装扩充卡提升板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 请重新将扩充卡安装到扩充卡提升板中(如果适用)。 2. 将扩充卡提升板对准连接器和系统板上的提升板导梢。 3. 放下扩充卡提升板,直至扩充卡提升板在连接器中完全就位。 4. 合上系统护盖。 5. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 6.
图 30: 卸下和安装 SD vFlash 卡 1. SD vFlash 卡 2. SD vFlash 卡插槽 3. 要安装 SD vFlash 卡,将带标签的一面朝上,将 SD 卡的触针一端插入模块上的卡插槽中。 备注: 为确保正确插入卡,插槽设置了键锁。 4. 将卡往里按,使其完全进入插槽并锁定。 卸下 vFlash 介质单元 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 拧下用于将 vFlash 介质单元固定到机箱的螺钉。 4. 从 vFlash 介质单元和背板上拔下电缆。 5. 朝机箱正面滑动 vFlash 介质单元,将其从系统中提出。 6. 合上系统护盖。 7.
图 31: 卸下和安装 vFlash 介质单元 1. 2. 3. 4. 电缆 螺钉 vFlash 介质单元 定位器 安装 vFlash 介质单元 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有已连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 朝机箱背面滑入并对齐 vFlash 介质单元。 4. 将电缆连接至 vFlash 介质单元。 5. 装回用于将 vFlash 介质单元固定到机箱的螺钉。 6. 合上系统护盖。 7.
卸下内部双 SD 模块 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下扩充卡提升板 3 和提升板中安装的所有插卡。 4. 找到系统板上 J_IDSDM 连接器上安装的内部双 SD 模块。 5. 如果有,请卸下 SD 插卡。 6. 抓住卡舌,拉动双 SD 模块将其从系统板上卸下。 7. 更换扩充卡提升板 3 并更换提升板中的插卡(如果有)。 8. 合上系统护盖。 9. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 图 32: 卸下和安装内部双 SD 模块 1. 2. 3. 4.
5. 系统板上的连接器 安装内部双 SD 模块 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下扩充卡提升板固定框架 3 和提升板中安装的所有插卡。 4. 在系统板上找到 J_IDSDM 连接器。 5. 将系统板上的连接器和双 SD 模块对齐。 6. 抓住卡舌,推拉双 SD 模块,直至其在系统板上稳固就位。 7. 更换扩充卡提升板 1 并更换提升板中的插卡(如果有)。 8. 合上系统护盖。 9.
备注: 为确保正确插入卡,插槽设置了键锁。 5. 将卡按入卡插槽,锁定到位。 6. 更换扩充卡提升板 3 并更换提升板中的插卡(如果有)。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 集成存储控制器卡 您系统的系统板上具有集成控制器卡专用的扩充卡插槽,该集成控制器卡为您系统的内部硬盘驱动器提供集成 存储子系统。控制器支持 SAS 和 SATA 硬盘驱动器,还可让您在系统附带的存储控制器版本支持的 RAID 配置 中设置硬盘驱动器。 卸下集成存储控制器卡 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下冷却导流罩。 4. 卸下扩充卡提升板 1。 5. 向下推插卡边缘的两个释放拉杆,使插卡与连接器脱离。 6.
图 33: 卸下和安装集成的存储控制器卡 1. 2. 3. 4. 系统板上的存储连接器 存储控制器卡 存储控制器卡固定器 释放拉杆(2 个) 安装集成存储控制器卡 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 卸下冷却导流罩。 4. 卸下扩充卡提升板 1。 5. 将插卡的一端与系统板上的卡固定器对齐。 6. 将插卡的另一端往下放入系统板上的存储控制器卡固定器。 7. 将卡往下按,直到它完全就位。 当插卡完全就位后,释放拉杆会卡住插卡边缘。 8. 更换扩充卡提升板 1。 9. 装回冷却导流罩。 10. 合上系统护盖。 11.
网络子卡 卸下网络子卡 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 请卸下扩充卡提升板 2 上的扩充卡(如果已安装)。 4. 使用 2 号梅花槽螺丝刀,松开将网络子卡固定至系统板的两颗固定螺钉。 5. 抓住网络子卡触点任一侧的边缘,将其提起以从系统板上的连接器上卸下。 6. 滑动网络子卡使其脱离系统背面,直至 NIC 连接器脱离背面板中的插槽。 7. 将网络子卡从机箱中取出。 图 34: 卸下和安装网络子卡 1. 2. 3. 4. 固定螺钉插槽(2 个) 系统板上的连接器 固定螺钉(2 个) 触点 5. 网络子卡 6.
1. 调整插卡的角度,使 RJ-45 连接器能够插入背面板中的插槽。 2. 将在插卡的后端的固定螺钉与系统板上的固定螺钉插槽对齐。 3. 按压插卡上的触点,直至插卡连接器在系统板连接器上稳固就位。 4. 使用 2 号梅花槽螺丝刀,拧紧这两颗固定螺钉以将网络子卡固定至系统板。 5. 将扩充卡安装到扩充卡提升板 2 中(如果适用)。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 处理器 请使用以下步骤进行: • 安装其它处理器 • 更换处理器 备注: 为确保系统充分冷却,您必须在所有空的处理器插座中安装处理器挡片和散热片挡片。 卸下处理器 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 在升级系统之前,请先从 support.dell.
图 35: 卸下和安装处理器散热器 1. 2. 3. 4. 散热器 固定插座(2 个) 固定螺钉(2 颗) 处理器 小心: 留在插座中的处理器承受着强大的压力。请注意,如果抓得不紧,释放拉杆可能会突然弹起。 8. 9.
图 36: 处理器护盖打开与合上拉杆的顺序 1. 2. 3. 4. 5. 闭锁符号 处理器插座释放拉杆 处理器 处理器插座释放拉杆 开锁符号 10. 向上转动处理器护盖直至其不影响处理器的取出。 小心: 插座插针属易碎品,可能会永久损坏。从插座中卸下处理器时,请注意不要弯曲插座上的插针。 11.
图 37: 卸下和安装处理器 1. 2. 3. 4. 5. 处理器插座释放拉杆 插针 1 指示符 处理器插座释放拉杆 处理器护盖 处理器 6. ZIF 插座 7. 插座卡锁(4 个) 8. 处理器凹口(4 个) 备注: 卸下处理器后,将其放在防静电的容器中以供重新使用、退回或临时存放。请勿触摸处理器的底 部。只能触摸处理器的侧边缘。 安装处理器 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 如果要安装单处理器,则必须在插座 CPU1 中安装。 1. 在升级系统之前,请先从 support.dell.com 下载最新的系统 BIOS 版本,按照下载的压缩文件中的说明在系 统上安装更新。 备注: 您可以使用 Lifecycle Controller(生命周期控制器)更新系统 BIOS。 2.
警告: 在系统关机后一定时间内,散热器和处理器都会很烫手。请让它们冷却下来后再进行操作。 5. 小心: 除非要移除处理器,否则绝对不要将散热片从处理器上移开。散热片是维持正常散热状态所必不可 少的。 卸下散热片/散热片挡片和处理器/处理器挡片(若适用)。 备注: 卸下散热片挡片或处理器挡片的步骤与卸下散热片或处理器的步骤相似。 6. 打开新处理器的包装。 7. 将处理器与 ZIF 插座中的插座卡锁对准。 小心: 处理器放置错位将永久破坏系统面板或者处理器本身。请留意不要弯曲底座内的管脚。 小心: 请勿用力安装处理器。当处理器位置对正时,应当轻松地放入底座。 8. 当处理器插座上的释放拉杆处于打开位置时,利用插座上插针 1 位置向导作为参考,对准处理器的插针 1 并在插座中轻轻放置处理器。 9. 合上处理器护盖。 10. 11. 转动锁定图标旁边的插座释放拉杆 直到它锁定入位。 同样,转动解锁图标旁边的插座释放拉杆 直到它锁定入位。 12. 使用干净、不起毛的软布擦去散热片上的导热油脂。 小心: 使用过多导热膏会导致多余的油膏溢出,接触并污染处理器底座。 13.
如果两个电源设备都处于活动状态比冗余电源设备处于休眠状态的效率更高,则活动电源设备也可激活处于休 眠状态的电源设备。如果活动电源设备上的负载超过 50%,则电源设备默认为唤醒两个电源设备,如果负载低 于 20%,则默认为使冗余电源设备进入休眠状态。 可使用 iDRAC 设置配置热备用功能。有关 iDRAC 设置的详情,请参阅 support.dell.com/manuals 上的《iDRAC7 用 户指南》。 卸下交流电源设备 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 系统正常运行时需要一个电源设备。在电源冗余系统中,每次只在电源开启的系统中卸下并更换一 个电源设备。 备注: 如果可选的电缆管理臂妨碍您卸下电源设备,则可能必须打开闩锁并将其提起。有关电缆管理臂的 详情,请参阅系统的机架说明文件。 1. 断开电源电缆与电源及要卸下的电源设备的连接,从紧固带卸下电缆。 2.
备注: 最大输出功率(以瓦特为单位)在电源设备标签上标示。 2. 卸下电源设备挡片(如果适用)。 3. 将新电源设备滑入机箱,直至电源设备完全就位,释放闩锁卡入到位。 4.
安装和连接安全接地线 警告: 对于使用 -(48-60) V 直流电源设备的设备,必须由合格的电工执行与直流电源连接相关的所有工作并 安全接地。请不要尝试亲自连接至直流电源或安装地线。所有电气布线必须遵从适用的当地或国家/地区 规范和惯例。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的所有安全说 明。 1. 剥除绿色/黄色线一端的绝缘层,露出约 4.5 毫米(0.175 英寸)的铜线。 2. 使用卷边工具(Tyco Electronics 58433-3 或类似工具)在绿色/黄色线(安全接地线)上卷起环形舌端子 (Jeeson Terminals Inc. R5-4SA 或类似端子)。 3. 使用锁紧垫圈配备的 #6-32 螺母,将安全接地线连接到系统背面的接地柱。 图 39: 安装和连接安全接地线 1. 2. 3. 4. 5.
警告: 连接直流电源线时颠倒极性会永久性地损坏电源设备或系统。 2. 将铜线端插入配套的连接器中,然后使用 2 号梅花槽螺丝刀拧紧配套连接器顶部的固定螺钉。 警告: 为防止电源设备受到静电放电的损坏,在将配套连接器插入电源设备前,必须用橡胶盖覆盖固定螺 钉。 3. 顺时针方向转动橡胶盖以将其安装到固定螺钉上。 4. 将配套连接器插入电源设备。 图 40: 安装直流输入电源线 1. 2. 3. 4. 直流电源插槽 橡胶盖 固定螺钉(2 颗) 直流电源连接器 5. –48 V 线 6. RTN 线 7.
图 41: 卸下和安装直流电源设备 1. 2. 3. 4. 5. 连接器 电源设备 电源设备状态指示灯 释放闩锁 电源设备手柄 安装直流电源设备 警告: 对于使用 -(48-60) V 直流电源设备的设备,必须由合格的电工执行与直流电源连接相关的所有工作并 安全接地。请不要尝试亲自连接至直流电源或安装地线。所有电气布线必须遵从适用的当地或国家/地区 规范和惯例。未经 Dell 授权的维修所造成的损坏不在保修范围内。请阅读并遵循产品附带的所有安全说 明。 1. 验证两个电源设备是否属于同一种类型且是否拥有相同的最大输出功率。 备注: 最大输出功率(以瓦特为单位)在电源设备标签上标示。 2. 卸下电源设备挡片(如果适用)。 3. 将新电源设备滑入机箱,直至电源设备完全就位且释放闩锁卡入到位。 备注: 如果打开了电缆管理臂的闩锁,请将其重新锁定。有关电缆管理臂的详情,请参阅系统的机架说明 文件。 4. 连接安全接地线。 5. 在电源设备中安装直流电源连接器。 小心: 在连接电源线时,使用紧固带将线缆固定至电源设备手柄。 6.
卸下电源设备挡片 小心: 为确保系统充分冷却,必须在非冗余配置中的第二个电源设备托架上安装电源设备挡片。只有在您 安装第二个电源设备时才卸下电源设备挡片。 如果要安装第二个电源设备,将电源设备挡片往外拉,使其离开托架。 图 42: 卸下和安装电源设备挡片 1. 电源设备挡片 安装电源设备挡片 备注: 仅将电源设备挡片安装在第二个电源设备托架中。 要安装电源设备挡片,请将挡片与电源设备托架对齐,并将其插入机箱,直至卡入到位。 系统电池 更换系统电池 警告: 如果新电池安装不正确,可能会有爆炸的危险。请仅使用相同类型或制造商推荐的类型更换电池。 请参阅安全信息以了解更多内容。 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 2. 打开系统护盖。 3. 卸下冷却导流罩。 4.
小心: 为避免损坏电池连接器,在安装或卸下电池时必须牢固地支撑住连接器。 5. 要卸下电池,通过稳固地向下按连接器的正极端来支撑电池连接器。 图 43: 更换系统电池 1. 电池连接器的正极端 2. 系统电池 3. 电池连接器的负极端 6. 从连接器负极端的固定卡舌中取出电池。 7. 要安装新的系统电池,通过稳固地向下按电池连接器的正极端来支撑电池连接器。 8. 拿住电池并使其“+”面朝上,将其滑入连接器正极端的固定卡舌下。 9. 竖直向下将电池按入连接器,直至其卡入到位。 10. 安装冷却导流罩。 11. 合上系统护盖。 12. 将系统重新连接至电源插座,并打开系统,包括所有连接的外围设备 13. 进入系统设置程序,以确认电池是否可以正常运行。 14. 在系统设置程序的 Time(时间)和 Date(日期)字段中输入正确的时间和日期。 15. 退出系统设置程序。 硬盘驱动器背板 您的系统支持 3.5 英寸(x12) SAS/SATA 背板和 2.
4. 小心: 您必须记下每个硬盘驱动器的编号并在卸下它们之前为其贴上临时标签,以便将其装回到原来的位 置。 卸下冷却导流罩。 5. 卸下冷却风扇部件。 6. 卸下所有硬盘驱动器。 7. 从背板断开 SAS/SATA/SSD 数据、信号和电源电缆的连接。 8. 按释放卡舌并向上滑动背板。 图 44: 卸下和安装 3.5 英寸 (x12) SAS/SATA 背板 1. 2. 3. 4. 5. 6. 7. 82 释放卡舌(2 个) 直通 I2C 电缆 左控制面板电缆 I2C 电缆 电源电缆 A USB 电缆 SAS 电缆(3 根) 8. 9. 10. 11. 12.
图 45: 布线图—3.5 英寸 (x12) SAS/SATA 背板 1. 2. 3. 4. 5. 电缆固定支架 系统板 集成存储控制器卡 系统板上的 SAS 连接器 SAS 背板 安装硬盘驱动器背板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 使用机箱基座的挂钩作为导向器以对齐硬盘驱动器背板。 2. 向下滑动硬盘驱动器背板,直至释放卡舌卡入到位。 3. 从背板断开 SAS/SATA/SSD 数据、信号和电源电缆的连接。 4. 装回冷却风扇部件。 5. 装回冷却导流罩。 6. 将硬盘驱动器安装在其原始位置。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 9.
卸下硬盘驱动器背板(背面) 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 小心: 为了防止损坏驱动器和背板,您必须先从系统中卸下硬盘驱动器,然后再卸下背板。 小心: 您必须记下每个硬盘驱动器的编号并在卸下它们之前为其贴上临时标签,以便将其装回到原来的位 置。 3. 卸下两个硬盘驱动器。 4. 断开背板上所有电缆的连接。 5. 提起释放销并将背板滑出机箱。 6. 提起背板,将其从机箱中取出。 图 46: 卸下和安装可选 2.5 英寸 (x2) 硬盘驱动器背板(背面) 1. 直通 I2C 电缆 2. I2C 电缆 84 3. 边带电缆 4.
5. SAS/SATA 连接器(2 个) 6. SAS 电缆 7. 释放销 图 47: 布线图—可选 2.5 英寸 (x2) 硬盘驱动器背板(背面) 1. 2. 3. 4. PCIe 卡固定器 硬盘驱动器背板(背面) 系统板 集成存储控制器卡 5. 系统板上的 SAS 连接器 6. 电缆固定支架 7. x12 硬盘驱动器背板 安装硬盘驱动器背板(背面) 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 将背板上的槽口与机箱上的槽口对齐。 4.
5. 松开释放销,将背板锁定到机箱上。 6. 重新接上所有连接至背板的电缆。 7. 将两个硬盘驱动器安装在其原始位置。 8. 合上系统护盖。 9. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 控制面板 卸下控制面板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 小心: 拔下控制面板电缆时,请勿用力过度,以免损坏连接器。 4. 通过拉动推拉卡舌断开控制面板电缆与背板的连接。 5. 卸下将 I/O 面板固定到机箱的三颗 Torx 螺钉。 6. 折叠靠近连接器的推拉卡舌。 7. 当您将连接器和推拉卡舌穿过机箱上的通道时,拉出控制面板电缆。 图 48: 卸下和安装控制面板 1. Torx 螺钉(3 颗) 86 2.
3. 推拉卡舌 4. 连接器 5. 硬盘驱动器背板 6. 机箱 安装控制面板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4. 围绕电缆折叠标签。 5. 折叠靠近连接器的推拉卡舌,并将连接器和推拉卡舌导入通道中。 6. 推拉电缆直至其完全通过该通道。 7. 拧紧这三颗 Torx 螺钉以将控制面板固定到机箱上。 备注: 您必须正确布置电缆以免其被夹住或卷曲。 8. 通过推拉连接器中心将电缆连接器连接到背板上。 9. 合上系统护盖。 10. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 11.
图 49: 卸下和安装 I/O 面板 1. 2. 3. 4. 5. I/O 面板电缆 硬盘驱动器背板 Torx 螺钉(3 颗) I/O 面板 机箱 安装 I/O 面板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果已安装前挡板,请将其卸下。 2. 关闭系统,包括所有已连接的外围设备,并断开系统与电源插座和外围设备的连接。 3. 打开系统护盖。 4. 围绕电缆折叠标签。 5. 推拉电缆直至其完全通过该通道。 小心: 要防止损坏 I/O 电缆,从硬盘驱动器背板上的连接器拔下或安装 I/O 电缆之前必须释放锁定卡舌。 6. 如果已锁定,顺时针旋转 I/O 电缆连接器上的锁定卡舌 90 度以释放锁。 7. 将 I/O 面板电缆连接至硬盘驱动器背板上的连接器。 8. 逆顺时针旋转 I/O 电缆连接器上的锁定卡舌 90 度以固定锁。 9.
11. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 12. 请安装前挡板(如果适用)。 系统板 卸下系统板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 小心: 如果使用带加密密钥的受信任的程序模块 (TPM),则会在程序或系统设置过程中提示您创建恢复密 钥。确保创建并安全存储此恢复密钥。如果更换此系统板,则必须在重新启动系统或程序时提供此恢复 密钥,然后才能访问硬盘驱动器上的加密数据。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 如果已安装前挡板,请将其卸下。 3. 打开系统护盖。 4.
a. 小型 SAS 电缆连接器 b. 金属卡舌 6. c. 系统板上的连接器 断开所有电缆与系统板的连接。 小心: 从机箱中卸下系统板时,请小心不要损坏系统识别按钮。 小心: 请勿通过抓住内存模块、处理器或其它组件来拿出系统板组件。 7. 抓住系统板固定器,提起蓝色的释放销,并将系统板滑向系统正面。 图 50: 卸下和安装系统板 1. 2. 3. 4. 系统板 系统板固定器 释放销 支撑架(仅在某些系统中有) 警告: 在系统关机后一定时间内,散热器和处理器都会很烫手。请让它们冷却下来后再进行操作。 8. 卸下散热器/散热器挡片和处理器/处理器挡片。 9. 卸下内存模块和内存模块挡板。 10. 卸下网络子卡。 安装系统板 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 打开新系统板部件的包装。 2.
a) 散热器/散热器挡片和处理器/处理器挡片 b) 内存模块和内存模块挡板 c) 网络子卡 小心: 请勿通过抓住内存模块、处理器或其它组件来拿出系统板组件。 小心: 将系统板放入机箱时,请小心不要损坏系统识别按钮。 3. 抓住触点,将系统板向下放入机箱。 4. 将系统板推向机箱后侧,直至系统板卡入到位。 5. 装回以下部件: a) b) c) d) e) f) g) h) i) 6. 电缆固定支架 PCIe 卡固定器 集成存储控制器卡 内部 USB 钥匙(如果已安装) 内部双 SD 模块 所有扩充卡提升板 冷却风扇部件 冷却导流罩 电源设备 将所有电缆重新连接至系统板。 备注: 确保系统内部的电缆均沿机箱壁布线,并使用电缆固定支架固定。 7. 合上系统护盖。 8. 将系统重新连接至电源插座,并打开系统和所有连接的外围设备。 9. 导入新的或现有的 iDRAC Enterprise 许可证。有关详情,请参阅 support.dell.
系统故障排除 4 安全第一 —— 为您和您的系统着想 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 系统启动失败故障排除 如果在通过 UEFI 引导管理器安装操作系统后将系统引导至 BIOS 引导模式,系统会挂起。反之亦然。您必须引 导至安装操作系统时所用的相同引导模式。 对于所有其他启动问题,请注意屏幕上显示的系统消息。 外部连接故障排除 对任何外部设备进行故障排除之前,请确保所有外部电缆均已牢固地连接至系统上的外部连接器。 视频子系统故障排除 1. 检查显示器与系统和电源的连接。 2. 检查系统到显示器之间的视频接口布线。 3. 运行相应的诊断检测程序。 如果检测程序运行成功,则问题与视频硬件无关。 如果检测程序运行失败,请参阅“获得帮助”。 USB 设备故障排除 按照以下步骤对 USB 键盘/鼠标进行故障排除。对于其它 USB 设备,请转至步骤 7。 1.
9. 重新连接,每次打开一个 USB 设备的电源。 10. 如果某个设备导致了相同的问题,请关闭该设备的电源,使用已知正常的电缆更换 USB 电缆,然后再打 开该设备的电源。 如果所有故障排除措施均失败,请参阅“获得帮助”。 串行 I/O 设备故障排除 1. 2. 关闭系统和所有已连接至串行端口的外围设备。 将串行接口电缆更换为可正常工作的电缆,并打开系统和串行设备。 如果问题得以解决,请使用已知正常的电缆更换接口电缆。 3. 关闭系统和串行设备,将该设备更换为同类设备。 4. 打开系统和串行设备。 如果问题仍然存在,请参阅“获得帮助”。 NIC 故障排除 1. 运行相应的诊断检测程序。有关可用的诊断检测程序,请参阅“使用系统诊断程序”。 2. 重新启动系统,并检查与 NIC 控制器相关的任何系统信息。 3.
– 扩充卡提升板(如果存在) – 扩充卡 – 电源设备 – 冷却风扇部件(如果有) – 冷却风扇 – 处理器和散热片 – 内存模块 4. 使系统彻底干燥至少 24 小时。 5. 重新安装您在步骤 3 中卸下的组件。 6. 合上系统护盖。 7. 打开系统和已连接的外围设备。 如果系统未正常启动,请参阅“获得帮助”。 8. 如果系统正常启动,请关闭系统并重新安装所有卸下的扩充卡。 9. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 如果检测程序运行失败,请参阅“获得帮助”。 受损系统故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3.
系统电池故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 如果长期(几个星期或几个月)关闭系统电源,则 NVRAM 可能会丢失系统配置信息。这种情况是 由有故障的电池引起的。 1. 在系统设置程序中重新输入时间和日期。 2. 关闭系统并断开系统与电源插座的连接,然后至少等待一小时。 3. 将系统重新连接至电源插座,并打开系统。 4.
1. 打开系统护盖。 2. 重置风扇或风扇的电源电缆。 3. 如果风扇运行正常,则关闭系统。 如果问题仍然存在,请参阅“获得帮助”。 系统内存故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 如果系统可以操作,请运行相应的诊断检测程序。有关可用的诊断测试程序,请参阅“使用系统诊断程 序”。 如果诊断程序指示出现故障,请按照诊断程序提供的更正措施进行操作。 2. 如果系统无法操作,请关闭系统和连接的外围设备,并且拔下系统的电源线。等待至少 10 秒钟,然后将 系统重新连接到电源。 打开系统和连接的外围设备,并留意屏幕上的信息。 3. 如果显示错误信息,指示特定内存模块有故障,请转至步骤 12。 4. 进入系统设置程序并检查系统内存设置。必要时对内存设置进行任何更改。 如果内存设置符合所安装的内存,但仍指示存在问题,请转至步骤 12。 5.
3. 打开系统护盖。 4. 找到 USB 闪存盘并予以重置。 5. 合上系统护盖。 6. 打开系统和连接的外围设备,并检查 USB 闪存盘是否运行正常。 7. 如果问题未解决,请重复步骤 2 和步骤 3。 8. 插入已知能正常工作的其它 USB 闪存盘。 9. 合上系统护盖。 如果问题仍未解决,请参阅“获得帮助”。 SD 卡故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 某些 SD 卡的卡上具有物理写保护开关。如果打开此写保护开关,则 SD 卡无法写入。 1. 进入系统设置程序,确保已启用 Internal SD Card Port(内部 SD 卡端口)。 2. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 3.
4. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 5. 打开系统护盖。 6. 卸下前挡板。 7. 确保接口电缆已牢固地连接至光盘驱动器和控制器。 8. 确保电源电缆已正确连接至驱动器。 9. 合上系统护盖。 如果问题仍未解决,请参阅获得帮助。 磁带备份装置故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 尝试使用其它盒式磁带。 2. 确保已正确安装和配置磁带备份装置的设备驱动程序。有关设备驱动程序的详情,请参阅您的磁带驱动器 说明文件。 3. 按照磁带备份软件说明文件中的说明重新安装磁带备份软件。 4. 确保磁带驱动器的接口电缆完全连接至控制器卡上的外部端口。 5. 检查控制器卡是否正确安装: a) b) c) d) e) 6.
4. 重新启动系统并进入系统设置程序。 5. 验证控制器是否已启用,以及系统设置程序中是否显示该驱动器。 如果问题仍然存在,请尝试进行扩充卡故障排除或参阅“获得帮助”。 存储控制器故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 备注: 对 SAS 或 PERC 控制器进行故障排除时,另请参阅操作系统和控制器的说明文件。 1. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 2. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 3. 打开系统护盖。 4. 验证已安装的扩展卡是否符合扩展卡安装原则。 5. 确保每个扩展卡都已在其连接器中稳固就位。 6. 合上系统护盖。 7. 将系统重新连接至电源插座,并打开系统和连接的外围设备。 8. 如果问题仍未解决,请关闭系统和连接的外围设备,然后断开系统与电源插座的连接。 9. 打开系统护盖。 10. 卸下系统中安装的所有扩展卡。 11.
6. 如果问题仍未解决,请关闭系统和连接的外围设备,然后断开系统与电源插座的连接。 7. 打开系统护盖。 8. 卸下系统中安装的所有扩充卡。 9. 合上系统护盖。 10. 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 如果检测程序运行失败,请参阅“获得帮助”。 11. 对于在步骤 8 中卸下的每个扩充卡,执行以下步骤: a) b) c) d) e) 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 打开系统护盖。 重新安装其中一个扩充卡。 合上系统护盖。 运行相应的诊断检测程序。有关详情,请参阅“使用系统诊断程序”。 如果仍然指示存在问题,请参阅“获得帮助”。 处理器故障排除 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 运行相应的诊断检测程序。有关可用的诊断检测程序,请参阅“使用系统诊断程序”。 2. 关闭系统和连接的外围设备,并断开系统与电源插座的连接。 3.
使用系统诊断程序 5 如果您的系统出现问题,请在致电 Dell 寻求技术帮助之前运行系统诊断程序。运行系统诊断程序旨在检测系统 的硬件,它不需要其它设备,也不会丢失数据。如果您无法自行解决问题,维修和支持人员可以使用诊断程序 的检测结果帮助您解决问题。 Dell Online Diagnostics Dell Online Diagnostics 是一组独立的诊断程序或检测模块套件,允许在生产环境的系统上运行诊断测试,并帮 助最大程度地延长系统正常工作的时间。Online Diagnostics 使您可以对硬盘驱动器、物理内存、网络接口卡 (NIC) 等机箱和存储组件运行诊断测试。可以使用图形用户界面 (GUI) 或命令行界面 (CLI) 对 Online Diagnostics 在 系统上查找到的硬件运行诊断测试。有关使用诊断程序的信息,请参阅 Dell Online PowerEdge Diagnostics 用户 指南,在软件 → 可维护性工具下,位于 support.dell.
系统诊断程序控制 菜单 说明 Configuration(配置) 显示所有检测到的设备的配置和状态信息。 Results(结果) 显示执行的所有检测的结果。 System Health(系统运行状况) 提供系统性能的当前概况。 Event Log(事件日志) 显示系统上运行的所有检测的结果的时间戳日志。如果至少记录一个事件描 述,则显示此选项。 有关嵌入式系统诊断程序的信息,请参阅 support.dell.
6 跳线和连接器 系统板跳线设置 有关重设密码跳线以禁用密码的信息,请参阅“禁用已忘记的密码”。 表.
系统板连接器 图 51: 系统板跳线和连接器 项目 连接器 说明 1 J_PS2 PSU 2 电源连接器 2 J_SATA_CD 光盘驱动器 SATA 连接器 3 J_SATA_TBU 磁带备份装置 SATA 连接器 4 J_BP0 光盘驱动器电源连接器 5 J_TBU 磁带备份装置电源连接器 6 J_PS1 PSU 1 电源连接器 7 J_IDSDM 内部双 SD 模块连接器 8 J_NDC 网络子卡连接器 9 J_RISER_3A 提升板 3 连接器 10 J_RISER_3B 提升板 3 连接器 106
项目 连接器 说明 11 J_USB USB 连接器 12 J_VIDEO_REAR 视频连接器 13 J_COM1 串行连接器 14 J_IDRAC_RJ45 iDRAC7 连接器 15 J_CYC 系统识别连接器 16 CYC_ID 系统识别按钮 17 J_RISER_2A 提升板 2 连接器 18 J_RISER_1A 提升板 1 连接器 19 J_RISER_2B 提升板 2 连接器 20 J_RISER_1B 提升板 1 连接器 21 J_STORAGE 集成的存储控制器卡连接器 22 J_SASX8 小型 SAS 连接器 23 J_USB_INT 内部 USB 连接器 24 J_SAS_PCH 用于软件 RAID 的 SAS 连接器 25 BAT 电池连接器 26 CPU2 处理器插槽 2 27 B10、B6、B2、B9、B5、B1 内存模块插槽 28 J_BP3 背板电源连接器 29 J_BP_SIG3 背板信号连接器 3 30 J_FAN2U_6 冷却风扇连接器 31
项目 连接器 说明 43 J_FP_USB 前面板 USB 连接器 44 J_BP_SIG1 背板信号连接器 1 45 J_BP_SIG0 背板信号连接器 0 禁用已忘记的密码 系统的软件安全保护功能包括系统密码和设置密码功能。密码跳线可以启用或禁用这些密码功能,也可以清除 当前使用的任何密码。 小心: 多数维修只能由经过认证的维修技术人员进行。您只能根据产品说明文件的授权,或者在联机或电 话服务和支持小组指导下,进行故障排除和简单的维修。未经 Dell 授权的维修所造成的损坏不在保修范 围内。请阅读并遵循产品附带的安全说明。 1. 关闭系统和所有连接的外围设备,并断开系统与电源插座的连接。 2. 打开系统护盖。 3. 将系统板跳线上的跳线从插针 4 和 6 移到插针 2 和 4。 4. 合上系统护盖。 当跳线设置在插针 2 和 4 上时,现有密码将在系统引导前不会被禁用(清除)。但在设定新的系统和/或设 置密码前,您必须将跳线移回插针 4 和 6。 5.
7 技术规格 处理器 处理器类型 • • 一个 Intel Xeon 处理器 E5-2609 或 E5-2630 产品 系列 或两个 Intel Xeon 处理器 E5-2400 产品系列 扩展总线 总线类型 PCI Express 第 3 代 使用提升卡的扩展槽: 提升板 1 (插槽 1)一个半高、薄型 x8 链路 (插槽 2)一个半高、薄型 x8 链路 (插槽 3)一个半高、薄型 x8 链路 提升板 2 (插槽 4)一个全高、全长 x16 链路 备注: 要使用插槽 1 至 4,必须安装两个处理器。 (插槽 5)一个全高、全长 x8 链路 提升板 3 (插槽 6)一个全高、全长 x16 链路 内存 体系结构 800 MT/s、1066 MT/s、1333 MT/s 或 1600 MT/s DDR3 已 注册、非缓冲或负载减少的错误纠正代码 (ECC) DIMM 支持高级 ECC 或内存优化操作 内存模块插槽 24 个 240 针插槽 内存模块容量 LRDIMM 32 GB 四列 RDIMM 2 GB、4 GB、8 GB 或 32 GB 单列、双列或四列 16 GB 单列
内存 LRDIMM 最大 768 GB RDIMM 最大 512 GB UDIMM 高达 64 GB 驱动器 硬盘驱动器 十二加二硬盘驱动器系统 硬盘驱动器插槽 0 至 11 和 12 至 13 中多达十二个 3.5 英 寸、内部、可热插拔 SAS、SATA、SATA SSD 或近线 SAS 驱动器,以及两个 2.5 英寸背部可访问的 SAS、近 线 SAS 或 SSD 硬盘驱动器。 连接器 背面 NIC 四个 10/100/1000 Mbps 或两个 10/100/1000 Mbps 以及 两个 100 Mbps/1 Gbps/10 Gbps 串行 9 针、DTE、16550 兼容 USB 两个 4 针 USB 2.0 兼容 视频 15 针 VGA 外部 vFlash 卡 一个闪存卡插槽,带有 iDRAC7 Enterprise 卡连接器 备注: 只有当您的系统上已安装 iDRAC7 Enterprise 许可证时才可使用此卡插槽。 前端 USB 一个 4 针、USB 2.0 兼容 视频 15 针 VGA 内部 USB 一个 4 针、USB 2.
环境参数 备注: 有关特定系统配置的环境测量值的其它信息,请参阅 dell.
环境参数 存储温度 112 -40°C 至 65°C(-40°F 至 149°F),最大温度变化梯度 为每小时 20°C。
8 系统消息 LCD 信息 备注: 仅在您的系统具有 LCD 显示屏时可用。 LCD 信息由简短的文字信息组成,指代系统事件日志 (SEL) 中记录的事件。有关 SEL 和配置系统管理设置的信 息,请参阅系统管理软件说明文件。 备注: 如果系统无法引导,按下系统 ID 按钮至少 5 秒钟,直至 LCD 上显示错误代码。记下该代码,然后参 阅“系统错误消息”。 查看 LCD 信息 如果发生系统错误,LCD 屏幕将变为琥珀色。请按 Select(选择)按钮,查看错误信息或状态信息列表。使用 向左和向右按钮突出显示错误编号,然后按 Select(选择)按钮查看该错误。 删除 LCD 信息 对于与传感器有关的故障,例如温度、电压、风扇等,当传感器恢复至正常状态时,LCD 信息将被自动删除。 对于其它故障,必须采取措施才能将信息从显示器中删除: • 清除 SEL — 您可以远程执行该任务,但是系统的事件历史记录将丢失。 • 关闭电源再打开 — 关闭系统电源并断开其与电源插座的连接;等待大约 10 秒钟,重新连接电源电缆, 然后重新启动系统。 系统错误消息 显示器中出现的系统消息,通知您系统可能出现的问题
错误代码 消息信息 详细信息 操作 系统板 电流超出适宜范围。 1. 审查系统电源策略。 2. 检查系统日志确认电源相关故障。 3. 审查系统配置更改。 4. 如果问题仍然存在,请参阅“获得帮助”。 AMP0303 消息 The system board current is greater than the upper critical threshold.(系统板 电流高于上限临界阈值。) LCD 消息 System board current is outside of range.(系统板 电流超出范围。) 详细信息 系统板 电流超出适宜范围。 操作 1. 审查系统电源策略。 2. 检查系统日志确认电源相关故障。 3. 审查系统配置更改。 4. 如果问题仍然存在,请参阅“获得帮助”。 ASR0000 ASR0001 ASR0002 ASR0003 BAT0002 114 消息 The watchdog timer expired.
错误代码 消息信息 BAT0017 CPU0000 CPU0001 CPU0005 CPU0010 CPU0023 CPU0204 消息 The battery has failed.(电池 失效。) LCD 消息 The battery has failed. Check battery.(电池 失效。检查电池。) 详细信息 电池 可能出现缺失、故障因为温度问题导致无法充电。 操作 检查系统风扇。如果问题仍然存在,请参阅“获得帮助”。 消息 CPU has an internal error (IERR).(CPU 出现内部错误 (IERR)。) LCD 消息 CPU has an internal error (IERR).
错误代码 消息信息 操作 1. 关闭系统并断开输入电源一分钟。 2. 确保处理器安装正确。 3. 重新提供输入电源并打开系统。 4. 如果问题仍然存在,请参阅“获得帮助”。 CPU0700 消息 CPU initialization error detected.(CPU 初始化错误。) LCD 消息 CPU initialization error detected. Power cycle system.(检测到 CPU 初始化错误。系统电源关闭然后打开。) 详细信息 系统 BIOS 无法初始化处理器。 操作 1. 关闭系统并断开输入电源一分钟。 2. 确保处理器安装正确。 3. 重新提供输入电源并打开系统。 4. 如果问题仍然存在,请参阅“获得帮助”。 CPU0701 消息 CPU protocol error detected.(检测到 CPU 协议错误。) LCD 消息 CPU protocol error detected.
错误代码 消息信息 LCD 消息 CPU bus initialization error detected. Power cycle system.(检测到 CPU 总线初始化错 误。系统电源关闭然后打开。) 详细信息 系统事件日志和操作系统日志也许会表明异常出现在处理器之外。 操作 1. 检查系统和操作系统日志以排查异常。如果未发现异常,则继续。 2. 关闭系统并断开输入电源一分钟。 3. 确保处理器安装正确。 4. 重新提供输入电源并打开系统。 5. 如果问题仍然存在,请参阅“获得帮助”。 CPU0704 消息 CPU machine check error detected.(检测到 CPU 机器检查错 误。) LCD 消息 CPU machine check error detected. Power cycle system.(检测到 CPU 机器检查错误。系统电源关闭然后打开。) 详细信息 系统事件日志和操作系统日志也许会表明异常出现在处理器之外。 操作 1.
错误代码 消息信息 HWC1001 HWC2003 HWC2005 MEM0000 消息 The is absent.( 缺失。) LCD 消息 The is absent. Check hardware.( 缺失。检查硬件。) 详细信息 缺失的设备可能是正常运行所必需。系统功能可能降级。 操作 重新安装或重新连接硬件。 消息 The storage cable is not connected, or is improperly connected.(未连接存储设 备 电缆,或连接不正确。) LCD 消息 Storage cable or interconnect failure. Check connection.
错误代码 消息信息 MEM0701 MEM0702 MEM1205 MEM1208 MEM8000 PCI1302 消息 Correctable memory error rate exceeded for .( 的可纠正内存错误 比率超限。) 详细信息 内存可能无法操作。这是未来可能发生的不可纠正错误的早期迹象。 操作 重新安装内存模块。如果问题仍然存在,请参阅“获得帮助”。 消息 Correctable memory error rate exceeded for .( 的可纠正内存错误 比率超限。) LCD 消息 Correctable memory error rate exceeded for . Re-seat memory.
错误代码 消息信息 PCI1304 PCI1308 PCI1320 消息 An I/O channel check error was detected.(检测到 I/O 通道检查错误。) LCD 消息 I/O channel check error detected. Power cycle system.(检测到 I/O 通道检查错误。系统 电源关闭然后打开。) 操作 关闭并打开输入电源,更新组件驱动程序,如果设备可卸下,则重新安装设备。 消息 A PCI parity error was detected on a component at bus devicefunction .(总线 设备 功能 上的组件检测到 PCI 奇偶校验错 误。) LCD 消息 PCI parity error on bus device function . Power cycle system.
错误代码 消息信息 PDR0001 PDR1016 PST0128 PST0129 PSU0001 PSU0002 操作 关闭并打开输入电源,更新组件驱动程序,如果设备可卸下,则重新安装设备。 消息 Fault detected on drive .(驱动器 上检测到故障。) LCD 消息 Fault detected on drive . Check drive.(驱动器 上检测到故障。检查 驱动器。) 详细信息 控制器在磁盘上检测到故障,并已使磁盘脱机。 操作 卸下然后重新安装有故障的磁盘。如果故障依然存在,请参阅“获得帮助”。 消息 Drive is removed from disk drive bay .(驱动器 从磁盘驱动器 托架 上卸下。) LCD 消息 Drive removed from disk drive bay . Check drive.
错误代码 消息信息 PSU0003 PSU0006 PSU0016 操作 卸下电源设备并在下次定期服务时重新安装。如果问题仍然存在,请参阅“获得帮 助”。 消息 The power input for power supply is lost.(电源设备 的电源输入丢 失。) LCD 消息 Power input for PSU is lost. Check PSU cables.(PSU 的电源输入缺 失。检查 PSU 电缆。) 详细信息 电源设备安装正确,但输入源未连接或未起作用。 操作 验证输入源连接到设备。验证输入源符合电源设备的操作要求。 消息 Power supply type mismatch.(电源设备 的类型不匹配。) LCD 消息 Power supply is incorrectly configured. Check PSU.
错误代码 消息信息 PSU0034 LCD 消息 PSU temperature outside of range. Check PSU.(PSU 温度超出范 围。请检查 PSU。) 详细信息 系统性能可能降级。 操作 检查系统运行环境,包括通风和进气孔温度。查看温度和热组件故障的日志。 消息 An under voltage fault detected on power supply .(在电源设备 上检 测到电压过低故障。) LCD 消息 An under voltage fault detected on PSU . Check power source.(在 PSU 上检测到电压过低故障。请检查电源。) 详细信息 此故障可能是系统中的电缆或子系统组件发生电力问题而导致。 操作 1. 卸下并重新安装电源设备。 2. 检查系统中的线缆和子系统组件以排查损坏。 3.
错误代码 消息信息 PSU1201 PSU1204 LCD 消息 PSU wattage mismatch; PSU = watts(PSU 功率不匹配;PSU = 瓦特 ) 详细信息 电源设备的输入类型和额定功率应当相同。 操作 安装匹配的电源设备, 并查阅此手册中的适当配置。 消息 Power supply redundancy is lost.(电源设备冗余缺失。) 详细信息 电源设备尝试在降级状态下运行。系统性能和电源冗余可能降级或缺失。 操作 检查输入电源。重新安装电源设备。如果问题依然存在,请参阅“获得帮助”。 消息 The power supplies are not redundant. Insufficient resources to maintain normal operations.(电源设备并非冗余。维持正常运行的资源不足。) LCD 消息 PSU redundancy degraded. Check PSU cables.
错误代码 消息信息 RFM1014 RFM1201 RFM2001 RFM2002 RFM2004 RFM2006 操作 重置闪存介质。如果问题仍然存在,请参阅“获得帮助”。 消息 Removable Flash Media is write protected.(可移动的闪存介质 为写保 护状态。) LCD 消息 Removable Flash Media is write protected. Check SD Card.(可移动的闪存介质 为写保护状态,检查 SD 卡。) 详细信息 该卡被 SD 卡上的物理闩锁进行了写保护。写保护状态的卡无法使用。 操作 如果是意外导致,卸下介质并禁用写保护。 消息 Internal Dual SD Module redundancy is lost.(内部双 SD 模块冗余缺失。) LCD 消息 Internal Dual SD Module redundancy is lost. Check SD Card.
错误代码 消息信息 SEC0031 SEC0033 SEL0006 SEL0008 SEL0012 SEL1204 TMP0118 消息 The chassis is open while the power is on.(电源开启状态下机箱打开。) LCD 消息 Intrusion detected. Check chassis cover.(检测到侵入。检查机箱盖。) 详细信息 机箱打开。系统性能可能降级,安全性可能无法保证。 操作 关闭机箱。检查系统日志。 消息 The chassis is open while the power is off.(电源关闭状态下机箱打开。) LCD 消息 Intrusion detected. Check chassis cover.(检测到侵入。检查机箱盖。) 详细信息 电源关闭状态下机箱打开。系统安全性可能已被破坏。 操作 关闭机箱并验证硬件资源。检查系统日志。 消息 All event logging is disabled.
错误代码 消息信息 TMP0119 消息 The system inlet temperature is less than the lower critical threshold.(系统进气孔温度低 于下限临界阈值。) LCD 消息 System inlet temperature is outside of range.(系统进气孔温度超出范围。) 详细信息 环境气温过低。 TMP0120 操作 检查系统运行环境。 消息 The system inlet temperature is greater than the upper warning threshold.(系统进气孔温 度高于上限警告阈值。) LCD 消息 System inlet temperature is outside of range.
诊断程序信息 如果在系统上运行诊断检测程序,则系统诊断公用程序可能会发出相关信息。有关系统诊断程序的详情,请参 阅“使用系统诊断程序”。 警报信息 系统管理软件可以为系统生成警报信息。警报信息包括针对驱动器、温度、风扇和电源状况的信息、状态、警 告和故障信息。有关详情,请参阅系统管理软件说明文件。 128
获得帮助 9 与 Dell 联络 备注: 如果没有可用的 Internet 连接,您可以在购货发票、装箱单、帐单或 Dell 产品目录上查找联络信 息。 Dell 提供了几种联机以及电话支持和服务选项。可用性会因国家和地区以及产品的不同而有所差异,某些服务 可能在您所在的区域不可用。有关销售、技术支持或客户服务问题,请与 Dell 联络: 1. 访问 support.dell.com。 2. 选择您的支持类别。 3. 如果您不是美国客户,请在 support.dell.com 页面底部选择国家代码,或者选择全部以查看更多选择。 4.