Dell PowerVault NX3300 소유자 매뉴얼 규정 모델: E16S Series 규정 유형: E16S001
주, 주의 및 경고 노트: "주"는 컴퓨터를 보다 효율적으로 사용하는 데 도움을 주는 중요 정보를 제공합니다. 주의: "주의"는 하드웨어 손상이나 데이터 손실의 가능성을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 경고: "경고"는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 알려줍니다. © 2012 Dell Inc. 본 설명서에 사용된 상표인 Dell™, Dell 로고, Dell Precision™ , OptiPlex™, Latitude™, PowerEdge™, PowerVault™, PowerConnect™, OpenManage™, EqualLogic™, Compellent™, KACE™, FlexAddress™, Force10™ 및 Vostro™는 Dell Inc.의 상표입니다. Intel®, Pentium®, Xeon®, Core® 및 Celeron®은 미국 및 다른 국가에서 Intel Corporation 의 등록 상표입니다.
목차 주, 주의 및 경고............................................................................................................................2 장 1: 시스템 정보..........................................................................................................................9 전면 패널 구조 및 표시등......................................................................................................................................9 LCD 패널 구조...............................................................................
활성화된 설정 암호를 사용하여 시스템 작동............................................................................................31 UEFI 부팅 관리자 시작..........................................................................................................................................32 부팅 관리자 탐색 키 사용..............................................................................................................................32 부팅 관리자 화면.......................................................................................
확장 카드 및 확장 카드 라이저...........................................................................................................................54 확장 카드 설치 지침.......................................................................................................................................54 확장 카드 분리................................................................................................................................................55 확장 카드 설치.........................................................
VGA 모듈................................................................................................................................................................83 VGA 모듈 분리.................................................................................................................................................83 VGA 모듈 설치.................................................................................................................................................84 시스템 보드.......................
장 7: 기술 사양..........................................................................................................................105 장 8: 시스템 메시지.................................................................................................................109 LCD 메시지...........................................................................................................................................................109 LCD 메시지 보기.......................................................................
1 시스템 정보 전면 패널 구조 및 표시등 그림 1 . 전면 패널 구조 및 표시등 항목 표시등, 단추 또는 커넥터 1 전원 켜짐 표시등, 전원 단 추 아이콘 설명 시스템 전원이 켜지면 전원 켜짐 표시등에 불이 켜집 니다. 전원 단추가 시스템에 대한 전원 공급 장치 출력 을 제어합니다. 노트: ACPI 를 지원하는 운영 체제에서 전원 단추를 사용하여 시스템을 끄면 시스템에 대한 전원 공급 이 끊어지기 전에 점진적 종료가 수행됩니다. 2 NMI 단추 특정 운영 체제를 실행할 때 소프트웨어 및 장치 드라 이버 오류에 대한 문제를 해결하는 데 사용됩니다. 종 이 클립 끝을 사용하여 이 단추를 누를 수 있습니다. 공인된 기술 지원 직원이 지시하거나 운영 체제 설명 서에 명시된 경우에만 이 단추를 사용합니다. 3 시스템 ID 단추 전면 및 후면 패널의 식별 단추를 사용하여 랙 내에서 특정 시스템을 찾을 수 있습니다.
항목 표시등, 단추 또는 커넥터 아이콘 설명 노트: DVD 장치는 데이터 전용입니다. 6 vFlash 매체 카드 슬롯 vFlash 매체 카드를 삽입할 수 있습니다. 7 LCD 메뉴 단추 제어판의 LCD 메뉴를 이동할 수 있습니다. 8 LCD 패널 시스템 ID, 상태 정보 및 시스템 오류 메시지를 표시합 니다. 시스템이 정상적으로 작동하는 동안 LCD 에 파 란색 불이 켜집니다. 시스템에 주의가 필요한 경우에 는 LCD 에 호박색 불이 켜지고 LCD 패널에 오류 코드가 표시된 후 설명 텍스트가 표시됩니다. 노트: 시스템이 AC 전원에 연결되어 있고 오류가 감지되면 시스템 전원이 켜져 있는지에 관계없이 LCD 에 황색 불이 켜집니다. 9 정보 태그 서비스 태그, NIC, MAC 주소 등의 시스템 정보를 필요 에 따라 기록할 수 있는 슬라이드형 레이블 패널입니 다. 10 비디오 커넥터 시스템에 VGA 디스플레이를 연결할 수 있습니다. 11 하드 드라이브 2.
항목 단추 설명 1 Left(왼쪽) 뒤쪽으로 커서를 한 단계 이동합니 다. 2 Select(선택) 커서에 의해 강조 표시된 메뉴 항목 을 선택합니다. 3 Right(오른쪽) 앞쪽으로 커서를 한 단계 이동합니 다. 메시지를 스크롤하는 동안 다음을 수행할 수 있습니다. • • • • 한 번 누르면 스크롤 속도가 증가합니다. 한 번 더 누르면 스크롤이 중 지됩니다. 다시 한 번 더 누르면 기본 스크롤 속도로 돌아갑니다. 다시 누르면 이 과정이 반복 됩니다. 홈 화면 홈 화면에 시스템에 대해 사용자가 구성할 수 있는 정보가 표시됩니다. 이 화면은 상태 메시지 또는 오류가 없는 상태로 시스템이 정상적으로 작동하는 동안 표시됩니다. 시스템이 대기 모드인 경우 오류 메시지가 없는 상태로 작업을 5 분 동안 수행하지 않으면 LCD 후광이 꺼집니다. 홈 화면을 보려면 세 개의 탐색 단추(선택, 왼쪽 또는 오 른쪽) 중 하나를 누릅니다.
View(보기) 메뉴 노트: View(보기) 메뉴에서 옵션을 선택하는 경우 다음 작업으로 진행하기 전에 옵션을 확인해야 합니다. 옵션 설명 iDRAC IP iDRAC7 에 대한 IPv4 또는 IPv6 주소를 표시합니다. 주소에는 DNS(주요 및 보조), 게이트웨이, IP 및 서 브넷이 포함됩니다(IPv6 에는 서브넷이 포함되지 않음). MAC iDRAC, iSCSI 또는 네트워크 장치에 대한 MAC 주소를 표시합니다. 이름 시스템의 호스트, 모델 또는 사용자 문자열의 이름을 표시합니다. 번호 시스템의 자산 태그 또는 서비스 태그를 표시합니다. 전원 시스템의 전력 출력을 BTU/시간 또는 와트 단위로 표시합니다. Setup(설치) 메뉴의 Set home(홈 설정) 하위 메뉴에서 표시 형식을 구성할 수 있습니다. 온도 시스템의 온도를 섭씨 또는 화씨 단위로 표시합니다. Setup(설치) 메뉴의 Set home(홈 설정) 하위 메뉴 에서 표시 형식을 구성할 수 있습니다.
메모리 표시등 상태 수정 조치 메모리 오류가 발생하면 이 표시등이 호박색으로 깜박 입니다. 오류가 있는 메모리의 위치를 확인하려면 시스템 이벤트 로그 또는 시스 템 메시지를 참조하십시오. 메모리 장치를 다시 설치하십시오. 문제가 계 속되면 도움말 얻기를 참조하십시오. 하드 드라이브 표시등 패턴 그림 3 . 하드 드라이브 표시등 1. 하드 드라이브 작동 표시등(녹색) 2. 하드 드라이브 상태 표시등(녹색 및 황색) 노트: 하드 드라이브가 고급 호스트 컨트롤러 인터페이스(AHCI) 모드에 있는 경우 오른쪽의 상태 표시등은 작동하지 않고 꺼져 있는 상태로 유지됩니다. 드라이브 상태 표시등 패턴(RAID 에만 해당) 상태 녹색으로 초당 2 번 깜박임 드라이브 식별 또는 분리 준비 상태 꺼짐 드라이브 삽입 또는 분리 대기 상태 노트: 시스템 전원이 켜진 후 모든 하드 드라이브가 초기화 될 때까지 드라이브 상태 표시등이 꺼진 상태로 유지됩니다.
후면 패널 구조 및 표시등 그림 4 . 후면 패널 구조 및 표시등 항목 표시등, 단추 또는 커넥터 1 시스템 ID 단추 아이콘 설명 전면 및 후면 패널의 식별 단추를 사용하여 랙 내에서 특정 시스템을 찾을 수 있습니다. 이러한 단추 중 하나 를 누르면 단추 중 하나를 다시 누를 때까지 전면에 있 는 LCD 패널과 후면에 있는 상태 표시등이 깜박입니다. 시스템 ID 를 설정 및 해제로 전환하려면 누릅니다. 게 시하는 동안 시스템의 응답이 중지되면 시스템 ID 단 추를 5 초 이상 누른 상태로 유지하여 BIOS 진행 모드 를 시작합니다. F2 iDRAC 설정에서 iDRAC 가 비활성화되지 않은 경우 iDRAC 를 재설정하려면 15 초 이상 누릅니다. 2 시스템 ID 커넥터 선택적 케이블 관리 암을 통해 선택적 시스템 상태 표 시등 조립품을 연결할 수 있습니다. 3 iDRAC7 엔터프라이즈 포 트 전용 관리 포트입니다. 4 직렬 커넥터 시스템에 직렬 장치를 연결할 수 있습니다.
항목 표시등, 단추 또는 커넥터 아이콘 설명 10 전원 공급 장치(PSU1) AC 11 전원 공급 장치(PSU2) 또는 DC 495W, 750W 또는 1100W 1100W(사용 가능한 경우) NIC 표시등 코드 그림 5 . NIC 표시등 1. 연결 표시등 2. 작동 표시등 표시등 표시등 코드 링크 및 작동 표시등이 꺼짐 NIC 가 네트워크에 연결되어 있지 않습니다. 링크 표시등이 녹색임 NIC 가 최대 포트 속도(1Gbps 또는 10Gbps)로 유효한 네트워크에 연결되어 있 습니다. 링크 표시등이 황색임 NIC 가 최대 포트 속도보다 낮은 속도로 유효한 네트워크에 연결되어 있습니 다. 작동 표시등이 녹색으로 점멸됨 네트워크 데이터를 전송하거나 수신하는 중입니다.
1. AC 전원 공급 장치 상태 표시등/핸들 그림 7 . DC 전원 공급 장치 상태 표시등 1. DC 전원 공급 장치 상태 표시등 전원 표 시등 패 턴 상태 꺼짐 전원이 연결되어 있지 않습니다. 녹색 전원 공급 장치에 유효한 전원이 연결되어 있으며 해당 전원 공급 장치가 작동 중인 경우 핸들/LED 표시등이 녹색으로 켜집니다. 황색 점 멸 전원 공급 장치에 문제가 있음을 나타냅니다. 주의: 전원 공급 장치 수정하는 경우 표시등이 점멸 상태인 전원 공급 장치만 교체하십시오. 쌍 을 맞추기 위해 다른 쪽 전원 공급 장치를 바꾸면 오류가 발생하여 시스템이 예기치 않게 종료될 수 있습니다. 고출력 구성에서 저출력 구성으로 또는 이와 반대로 변경하려면 시스템의 전원을 꺼야 합니다. 주의: AC 전원 공급 장치에서는 220V 와 110V 입력 전압을 모두 지원합니다. 동일한 두 전원 공급 장치에서 서로 다른 입력 전압을 수신하면 서로 다른 전력량(와트)을 출력하고 불일치가 발생할 수 있습니다.
• 사용 설명서에 시스템 설정 개요 및 기술 사양이 제공되어 있습니다. 이 설명서는 support.dell.com/ manuals 에서 온라인으로 사용할 수 있습니다. • 랙 솔루션과 함께 제공되는 랙 설명서에는 필요한 경우 시스템을 랙에 설치하는 방법이 설명되어 있습니 다. • 운영 체제, 시스템 관리 소프트웨어, 시스템 업데이트 및 시스템과 함께 구입한 시스템 구성요소와 관련 된 설명서 및 도구를 비롯하여 시스템을 구성 및 관리하는 데 필요한 설명서 및 도구를 제공하는 모든 매 체가 시스템과 함께 제공됩니다. • 이 표에서 사용된 약어 및 머리글자의 전체 이름은 용어집(support.dell.com/manuals)을 참조하십시오. 노트: 새로운 업데이트가 없는지 support.dell.com/manuals 에서 항상 확인하십시오. 업데이트에는 최신 정 보가 수록되어 있으므로 다른 문서를 읽기 전에 반드시 먼저 참조하시기 바랍니다.
2 시스템 설정 및 부팅 관리자 사용 시스템 설정을 통해 시스템 하드웨어를 관리하고 BIOS 레벨 옵션을 지정할 수 있습니다. 시작하는 동안 시스템 기능에 액세스하려면 다음 키를 입력합니다. 키입력 설명 시스템 설정을 시작합니다. 시스템 서비스를 시작하여 Dell Lifecycle Controller 2(LC2)를 엽니다. Dell LC2 는 그래픽 사용자 인터페이 스를 사용하여 운영 체제 배포, 하드웨어 진단, 플랫폼 업데이트 및 플랫폼 구성과 같은 시스템 관리 기 능을 지원합니다. 정확한 LC2 기능 집합은 구입하는 iDRAC 라이센스에 따라 다릅니다. 자세한 내용은 Dell LC2 설명서를 참조하십시오. 시스템의 부팅 구성에 따라 BIOS 부팅 관리자 또는 UEFI(Unified Extensible Firmware Interface) 부팅 관리 자를 시작합니다. PXE(Preboot eXecution Environment) 부팅을 시작합니다.
를 계속해서 설치합니다. 설치 후 설치한 운영 체제에 액세스하려면 동일한 부팅 모드(BIOS 또는 UEFI)에서 시스 템을 부팅해야 합니다. 다른 부팅 모드에서 운영 체제를 부팅하려고 시도하면 시스템이 시작 시 중단됩니다. 노트: UEFI 부팅 모드에서 운영 체제를 설치하려면 운영 체제가 UEFI 와 호환되어야 합니다. DOS 및 32 비트 운영 체제는 UEFI 를 지원하지 않으며 BIOS 부팅 모드에서만 설치될 수 있습니다. 노트: 지원되는 운영 체제에 대한 최신 정보를 보려면 dell.com/ossupport 로 이동하십시오. 시스템 설정 시작 1. 시스템을 켜거나 재시작합니다. 2. 다음과 같은 메시지가 나타나면 즉시 키를 누릅니다. = System Setup( = 시스템 설정) 키를 누르기 전에 운영 체제가 로드되기 시작하면 시스템이 부팅을 완료하게 한 다음 시스템을 재시작 하고 다시 시도합니다.
시스템 설정 Main(기본) 화면 노트: BIOS 또는 UEFI 설정을 기본 설정값으로 재지정하려면 를 누릅니다. 메뉴 항목 설명 System BIOS(시스템 BIOS) 이 옵션은 BIOS 설정을 확인하고 구성하는 데 사용됩니다. iDRAC Settings(iDRAC 설정) 이 옵션은 iDRAC 설정을 확인하고 구성하는 데 사용됩니다. Device Settings(장치 설정) 이 옵션은 장치 설정을 확인하고 구성하는 데 사용됩니다. System BIOS(시스템 BIOS) 화면 노트: 시스템 설정의 옵션은 시스템 구성에 따라 변경됩니다. 노트: 시스템 설정 기본값은 다음 항목에서 각 해당 옵션 아래에 표시됩니다. 메뉴 항목 설명 System Information(시스템 정보) 시스템 모델 이름, BIOS 버전, 서비스 태그 등의 시스템에 대한 정보를 표시합 니다. Memory Settings(메모리 설정) 설치된 메모리와 관련된 정보 및 옵션을 표시합니다.
메뉴 항목 설명 System BIOS Version(시스템 BIOS 버전) 시스템에 설치된 BIOS 버전을 표시합니다. System Service Tag(시스템 서비스 태그) 시스템 서비스 태그를 표시합니다. System Manufacturer(시스템 제조업체) 시스템 제조업체 이름을 표시합니다. System Manufacturer Contact Information(시스템 제조업체 연락 시스템 제조업체의 연락처 정보를 표시합니다. 처 정보) Memory Settings(메모리 설정) 화면 메뉴 항목 설명 System Memory Size(시스템 메모리 크기) 시스템에 설치된 메모리 크기를 표시합니다. System Memory Type(시스템 메모리 종류) 시스템에 설치된 메모리 종류를 표시합니다. System Memory Speed(시스템 시스템 메모리 속도를 표시합니다.
Processor Settings(프로세서 설정) 화면 메뉴 항목 설명 Logical Processor(논리 프로 논리 프로세서를 활성화하거나 비활성화하고 논리 프로세서의 개수를 표시합니 세서) 다. Logical Processor(논리 프로세서) 옵션이 Enabled(활성화)로 설정된 경우, BIOS 는 모든 논리 프로세서를 표시합니다. 이 옵션이 Disabled(비활성화)로 설정되어 있으면 BIOS 는 논리 프로세서를 코어당 1 개만 표시합니다. 기본적으로 Logical Processor(논리 프로세서) 옵션은 Enabled(활성화)로 설정됩니다. QPI Speed(QPI 속도) QuickPath Interconnect 데이터 속도 설정값을 지정합니다. 기본적으로 QPI Speed(QPI 속도) 옵션은 Maximum data rate(최대 데이터 속도)로 설정됩니다. 노트: QPI Speed(QPI 속도) 옵션은 두 프로세서가 모두 설치된 경우에만 표시 됩니다.
설명 메뉴 항목 노트: Processor Bus Speed(프로세서 버스 속도) 옵션은 두 프로세서가 모두 설 치되어 있는 경우에만 표시됩니다. 프로세서 1 노트: 시스템에 설치된 각 프로세서에 대해 다음 설정이 표시됩니다. Family-Model-Stepping(제품 군-모델-스테핑) Intel 에서 정의한 대로 프로세서의 제품군, 모델 및 스테핑을 표시합니다. Brand(브랜드) 프로세서에서 보고되는 브랜드 이름을 표시합니다. Level 2 Cache(수준 2 캐시) 전체 L2 캐시를 표시합니다. Level 3 Cache(수준 3 캐시) 전체 L3 캐시를 표시합니다. Number of Cores(코어 수) 프로세서당 코어 수를 표시합니다. SATA Settings(SATA 설정) 화면 메뉴 항목 설명 Embedded SATA(내장형 SATA) 내장형 SATA 를 Off(끄기), ATA, AHCI 또는 RAID 모드로 설정할 수 있습니다.
메뉴 항목 설명 기본적으로 Boot Sequence Retry(부팅 순서 재시도) 옵션은 Disabled(비활성화)로 설정 됩니다. BIOS Boot Settings(BIOS 부팅 설 정) BIOS 부팅 옵션을 활성화하거나 비활성화할 수 있습니다. 노트: 이 옵션은 부팅 모드가 BIOS 인 경우에만 활성화됩니다. UEFI Boot Settings(UEFI UEFI 부팅 옵션을 활성화하거나 비활성화할 수 있습니다. 부팅 설정) 노트: 이 옵션은 부팅 모드가 UEFI 인 경우에만 활성화됩니다. One-Time Boot(원타임 부팅) 선택한 장치에서의 원타임 부팅을 활성화하거나 비활성화할 수 있습니다. Integrated Devices(내장형 장치) 화면 메뉴 항목 설명 Integrated RAID 내장형 RAID 컨트롤러를 활성화하거나 비활성화합니다.
메뉴 항목 설명 Embedded Video Embedded Video Controller(내장형 비디오 컨트롤러)를 활성화하거나 비활성화합니 Controller(내장형 비디오 다. 기본적으로 내장형 비디오 컨트롤러는 Enabled(활성화)로 설정됩니다. 컨트롤러) SR-IOV Global Enable(SRIOV 글로벌 활성화) SR-IOV(Single Root I/O Virtualization) 장치의 BIOS 구성을 활성화하거나 비활성화합니 다. 기본적으로 SR-IOV Global Enable(SR-IOV 글로벌 활성화) 옵션은 Disabled(비활성 화)로 설정됩니다. Slot Disablement(슬롯 비 활성화) 시스템에서 사용 가능한 PCIe 슬롯을 활성화하거나 비활성화할 수 있습니다. Slot Disablement(슬롯 비활성화) 기능은 지정된 슬롯에 설치된 PCIe 카드의 구성을 제어 합니다.
System Profile Settings(시스템 프로필 설정) 화면 메뉴 항목 설명 System Profile(시스템 프 시스템 프로필을 설정합니다. System Profile(시스템 프로필) 옵션을 Custom(사용자 로필) 정의) 이외의 다른 모드로 설정하는 경우, BIOS 가 자동으로 나머지 옵션을 설정합니 다. 모드가 Custom(사용자 정의)으로 설정된 경우에만 사용자가 나머지 옵션을 변경 할 수 있습니다. 기본적으로 System Profile(시스템 프로필) 옵션은 Performance Per Watt Optimized (DAPC)(와트당 성능 최적화(DAPC))로 설정됩니다. DAPC 는 Dell Active Power Controller 의 약자입니다. 노트: 다음 매개 변수는 System Profile(시스템 프로필)이 Custom(사용자 정의)으로 설정된 경우에만 사용할 수 있습니다. CPU Power Management(CPU 전원 관리) CPU 전원 관리를 설정합니다.
System Security(시스템 보안) 화면 메뉴 항목 설명 Intel AES-NI Intel AES-NI 옵션은 고급 암호화 표준 명령 집합을 사용해 암호화 및 암호 해독을 수행 하여 응용프로그램의 속도를 향상하며 기본적으로 Enabled(활성화)로 설정됩니다. System Password(시스 시스템 암호를 설정할 수 있습니다. 기본적으로 이 옵션은 Enabled(활성화)로 설정되 템 암호) 며, 시스템에 암호 점퍼가 설치되어 있지 않은 경우 읽기 전용입니다. Setup Password(설정 암호) 설정 암호를 설정합니다. 시스템에 암호 점퍼가 설치되지 않은 경우 이 옵션은 읽기 전 용입니다. Password Status(암호 상태) 시스템 암호를 잠급니다. 기본적으로 Password Status(암호 상태) 옵션은 Unlocked(잠 금 해제)로 설정됩니다. TPM Security(TPM 보 안) TPM(Trusted Platform Module)의 보고 모드를 제어합니다.
설명 메뉴 항목 AC Power Recovery 시스템에 AC 전원이 복원된 후 시스템에서 전원 켜기의 스태거를 지원하는 방법을 설 Delay(AC 전원 복구 지 정할 수 있습니다. 기본적으로 AC Power Recovery Delay(AC 전원 복구 지연) 옵션은 연) Immediate(즉시)로 설정됩니다. User Defined Delay(사 용자 정의 지연)(60 초 ~ 240 초) AC Power Recovery Delay(AC 전원 복구 지연)에 User Defined(사용자 정의) 옵션이 선택 되어 있는 경우 User Defined Delay(사용자 정의 지연)를 설정할 수 있습니다. Miscellaneous Settings(기타 설정) 메뉴 항목 설명 System Time(시스템 시간) 시스템의 시간을 설정합니다. System Date(시스템 날짜) 시스템의 날짜를 설정합니다.
시스템 및/또는 설정 암호 지정 노트: 암호 점퍼는 시스템 암호 및 설정 암호 기능을 활성화하거나 비활성화합니다. 암호 점퍼 설정에 대한 자세한 내용은 '시스템 보드 점퍼 설정'을 참조하십시오. 암호 점퍼 설정이 활성화되어 있고 Password Status(암호 상태)가 Unlocked(잠금 해제)인 경우에만 새 System Password(시스템 암호) 및/또는 Setup Password(설정 암호)를 지정하거나 기존 System Password(시스템 암호) 및/ 또는 Setup Password(설정 암호)를 변경할 수 있습니다. Password Status(암호 상태)가 Locked(잠금)이면 시스템 암호 및/또는 설정 암호를 변경할 수 없습니다. 암호 점퍼 설정이 비활성화되어 있고 기존 시스템 암호 및 설정 암호가 삭제된 경우, 시스템에 로그온하기 위해 시스템 암호를 제공하지 않아도 됩니다. 새 시스템 암호 및/또는 설정 암호를 지정하려면 다음과 같이 합니다. 1.
System BIOS(시스템 BIOS) 화면이 표시됩니다. 3. System BIOS(시스템 BIOS) 화면에서 System Security(시스템 보안)를 선택하고 키를 누릅니다. System Security(시스템 보안) 화면이 표시됩니다. 4. System Security(시스템 보안) 화면에서 Password Status(암호 상태)가 Unlocked(잠금 해제)인지 확인합니다. 5. System Password(시스템 암호)를 선택하고 기존 시스템 암호를 변경하거나 삭제한 후, 또는 키를 누릅니다. 6. Setup Password(설정 암호)를 선택하고 기존 설정 암호를 변경하거나 삭제한 후, 또는 키를 누 릅니다. 노트: 시스템 및/또는 설정 암호를 변경하면 새 암호를 다시 입력하라는 메시지가 표시됩니다. 시스템 및/또 는 설정 암호를 삭제하면 삭제할지 여부를 확인하라는 메시지가 표시됩니다. 7.
노트: 시스템 암호가 무단으로 변경되지 않도록 방지하려면 Setup Password(설정 암호) 옵션과 Password Status(암호 상태) 옵션을 함께 사용할 수 있습니다. UEFI 부팅 관리자 시작 노트: UEFI 부팅 모드에서 운영 체제를 설치하려면 해당 운영 체제가 64 비트 UEFI 호환 운영 체제(예: Microsoft Windows Server 2008 x64 버전)여야 합니다. DOS 및 32 비트 운영 체제는 BIOS 부팅 모드에서만 설 치할 수 있습니다. 이 부팅 관리자를 사용하면 다음 작업을 수행할 수 있습니다. • 부팅 옵션 추가, 삭제 및 정렬 • 재부팅 없이 시스템 설정 및 BIOS 수준 부팅 옵션에 액세스 이 부팅 관리자를 시작하려면 다음을 수행하십시오. 1. 시스템을 켜거나 재시작합니다. 2. 다음과 같은 메시지가 나타나면 키를 누릅니다.
메뉴 항목 설명 BIOS Boot Menu(BIOS 부 사용 가능한 BIOS 부팅 옵션(별표로 표시됨)의 목록을 표시합니다. 사용할 부팅 옵션 팅) 메뉴 을 선택하고 키를 누릅니다. UEFI Boot Menu(UEFI 부 팅) 메뉴 사용 가능한 UEFI 부팅 옵션(별표로 표시됨)의 목록을 표시합니다. 사용할 부팅 옵션 을 선택하고 키를 누릅니다. UEFI 부팅 메뉴를 통해 Add Boot Option(부팅 옵션 추가), Delete Boot Option(부팅 옵션 삭제) 또는 Boot From File(파일에서 부팅)을 선택 할 수 있습니다. Driver Health Menu(드라 시스템에 설치된 드라이버의 목록 및 해당 드라이버의 상태를 표시합니다. 이버 상태) 메뉴 Launch System Setup(시 스템 설정 시작) 시스템 설정에 액세스할 수 있습니다.
iDRAC 설정 유틸리티 시작 1. 관리되는 시스템을 켜거나 재시작합니다. 2. POST(Power-On Self-Test) 중에 키를 누릅니다. 3. System Setup Main Menu(시스템 설정 기본 메뉴) 페이지에서 iDRAC Settings(iDRAC 설정)를 클릭합니다. iDRAC Settings(iDRAC 설정) 화면이 표시됩니다.
3 시스템 구성요소 설치 권장 도구 이 섹션의 절차를 수행하려면 다음 품목이 필요할 수 있습니다. • 시스템 키 잠금 장치의 키 • #1 및 #2 십자 드라이버 • T10 및 T15 Torx 드라이버 • 접지에 연결된 손목 접지대 DC 전원 공급 장치(PSU)의 케이블을 조립하려면 다음 도구가 필요합니다(사용 가능한 경우). • 10 AWG 크기의 솔리드 또는 꼬인 절연 구리선으로부터 절연체를 제거할 수 있는 와이어 스트리퍼 펜치 • AMP 90871-1 압착기 또는 이와 동등한 공구 노트: 알파 와이어 부품 번호 3080 또는 이와 동등한 부품을 사용합니다(65/30 스트랜딩). 전면 베젤(선택사양) 전면 베젤 분리 1. 베젤의 왼쪽 끝에 있는 키 잠금 장치의 잠금을 해제합니다. 2. 키 잠금 장치 옆에 있는 분리 래치를 들어 올립니다. 3. 베젤의 왼쪽 끝을 회전하여 전면 패널에서 분리합니다. 4.
1. 2. 3. 4. 분리 래치 키 잠금 장치 전면 베젤 잠금 고리 전면 베젤 장착 1. 베젤의 오른쪽 끝을 섀시에 겁니다. 2. 베젤의 자유 단을 시스템에 맞춥니다. 3. 키 잠금 장치를 사용하여 베젤을 고정합니다. 시스템 열기 및 닫기 경고: 시스템을 들어 올려야 할 경우에는 다른 사람의 도움을 받으십시오. 부상을 피하려면 혼자 힘으로 시 스템을 들어 올리지 마십시오. 경고: 시스템이 켜져 있는 상태에서 시스템 덮개를 열거나 분리하면 감전의 위험에 노출될 수 있습니다. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 9 . 시스템 열기 및 닫기 1. 시스템 덮개 2. 래치 3. 분리 래치 잠금 장치 시스템 닫기 1. 덮개에 있는 래치를 들어 올립니다. 2. 덮개로 섀시를 덮은 다음 뒤로 살짝 밀어 덮개가 섀시 고리에 걸린 상태로 섀시 위에 평평하게 놓이도록 합 니다. 3. 래치를 아래로 눌러 덮개를 닫힘 위치로 움직입니다. 4. 분리 래치 잠금 장치를 시계 방향으로 돌려 덮개를 고정합니다. 5. 시스템을 콘센트에 다시 연결하고 시스템 및 연결된 주변 장치의 전원을 모두 켭니다. 시스템 내부 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 10 . 시스템 내부 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 제어판 조립품 케이블 보호 클립 냉각 팬(7 개) 케이블 보호 브래킷 냉각 덮개 전원 공급 장치(2 개) 섀시 침입 스위치 라이저 카드 3 네트워크 도터 카드 라이저 카드 2 11. 12. 13. 14. 15. 16. 17. 18. 내장형 저장소 컨트롤러 카드 네트워크 도터 카드 냉각 덮개 DIMM(24 개) 프로세서 2 방열판 하드 드라이브 후면판 콘솔 하드 드라이브(4 개) 광학 드라이브 냉각 덮개 냉각 덮개 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
그림 11 . 냉각 덮개 분리 및 설치 1. 냉각 덮개 냉각 덮개 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 섀시에 냉각 덮개를 올바르게 장착하려면 시스템 내의 케이블이 섀시 벽을 따라 배선되어 있고 케이 블 보호 브래킷을 사용하여 고정되어 있는지 확인합니다. 1. 냉각 덮개의 탭을 섀시의 고정 슬롯에 맞춥니다. 2. 단단히 고정될 때까지 냉각 덮개를 섀시 쪽으로 내립니다. 3. 해당하는 경우 전체 길이 PCIe 카드를 교체합니다. 4. 시스템을 닫습니다. 5. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다.
시스템에는 24 개의 메모리 소켓이 12 개씩 두 세트(프로세서당 한 세트)로 분할되어 포함되어 있습니다. 12 개 소 켓을 포함하는 각 세트는 4 개의 채널로 구성됩니다. 각 채널에서 첫 번째 소켓의 분리 레버는 흰색으로 표시되 고, 두 번째 소켓의 분리 레버는 검정색으로 표시되고, 세 번째 소켓의 분리 레버는 녹색으로 표시됩니다. 노트: A1-A12 소켓의 DIMM 은 프로세서 1 에 할당되고 B1-B12 소켓의 DIMM 은 프로세서 2 에 할당됩니다. 그림 12 . 메모리 소켓 위치 메모리 채널은 다음과 같이 구성됩니다.
채널 1: 슬롯 B2, B6 및 B10 채널 2: 슬롯 B3, B7 및 B11 채널 3: 슬롯 B4, B8 및 B12 다음 표는 지원되는 구성의 메모리 장착 및 작동 주파수를 보여 줍니다. DIMM 유형 장착되는 DIMM/ 채널 최대 DIMM 랭크/채널 작동 주파수(MT/s) 1.5V 1.
• • 성능을 극대화하려면 프로세서당 4 개의 DIMM(채널당 1 개의 DIMM)을 동시에 장착합니다. 각각 다른 속도를 가진 메모리 모듈이 설치되면 설치된 메모리 모듈 중 가장 느린 모듈의 속도로 작동하 거나 시스템 DIMM 구성에 따라 더 느린 속도로 작동하게 됩니다. 모드별 지침 4 개의 메모리 채널이 각 프로세서에 할당됩니다. 허용되는 구성은 선택한 메모리 모드에 따라 다릅니다. 노트: x4 및 x8 DRAM 기반 DIMM 은 혼합되어 RAS 기능에 대한 지원을 제공할 수 있습니다. 그러나 특정 RAS 기능에 대한 모든 지침이 준수되어야 합니다. x4 DRAM 기반 DIMM 은 메모리 최적화(독립 채널) 모드에서 SDDC(Single Device Data Correction)를 유지합니다. x8 DRAM 기반 DIMM 의 경우 SDDC 가 지원되도록 하려 면 고급 ECC 모드가 필요합니다. 다음 항목에서는 각 모드별로 추가적인 슬롯 채우기 지침을 제공합니다.
메모리 구성 예 다음 표는 이 섹션에 설명되어 있는 해당 메모리 지침을 준수하는 하나 및 두 개의 프로세서 구성에 대한 샘플 메 모리 구성을 보여줍니다. 노트: 16GB 4 중 랭크 RDIMM 은 지원되지 않습니다. 노트: 다음 표에서 1R, 2R 및 4R 은 각각 싱글, 이중 및 4 중 랭크 DIMM 을 나타냅니다. 표 1.
시스템 용량 (GB) DIMM 크기 (GB) DIMM 개수 DIMM 랭크, 조직 및 빈도 DIMM 슬롯 채우기 384 32 12 LRDIMM, x4, 1333MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12 표 2.
시스템 용량 (GB) DIMM 크기(GB) DIMM 개수 DIMM 랭크, 조직 및 빈 도 DIMM 슬롯 채우기 256 16 16 2R, x4, 1333MT/s, 2R, x4, 1600MT/s, A1, A2, A3, A4, A5, A6, A7, A8 B1, B2, B3, B4, B5, B6, B7, B8 384 16 24 2R, x4, 1333MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12 B1, B2, B3, B4, B5, B6, B7, B8, B9, B10, B11, B12 32 12 4R, x4, 1333MT/s A1, A2, A3, A4, A5, A6 B1, B2, B3, B4, B5, B6 512 32 16 4R, x4, 1066MT/s 4R, x4, 1333MT/s A1, A2, A3, A4, A5, A6, A7, A8 B1, B2, B3, B4, B5, B6, B7, B8 768 32 24 LRDI
그림 13 . 메모리 모듈 분리 및 설치 1. 메모리 모듈 2. 메모리 모듈 소켓 배출기(2 개) 3. 맞춤 키 6. 시스템이 올바르게 냉각되도록 빈 메모리 모듈 소켓에 메모리 모듈 보호물을 설치합니다. 7. 냉각 덮개를 설치합니다. 8. 시스템을 닫습니다. 9. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 메모리 모듈 설치 경고: 메모리 모듈은 시스템 전원을 끈 후에도 얼마 동안 뜨거울 수 있습니다. 메모리 모듈을 다루기 전에 냉각될 때까지 기다리십시오. 메모리 모듈을 다룰 때에는 카드 모서리를 잡고 메모리 모듈의 구성 요소를 만지지 않도록 하십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다.
노트: 나중에 사용할 수 있도록 분리된 메모리 모듈 보호물을 보관합니다. 주의: 메모리 모듈의 중간 부분을 건드리지 않도록 주의하면서 메모리 모듈의 양쪽 카드 모서리만 잡으십 시오. 6. 메모리 모듈의 에지 커넥터를 메모리 모듈 소켓의 맞춤 키에 맞추고 메모리 모듈을 소켓에 삽입합니다. 노트: 메모리 모듈 소켓에는 메모리 모듈을 한 방향으로만 소켓에 설치하도록 하는 맞춤 키가 있습니다. 7. 소켓 레버가 잠금 위치에 걸릴 때까지 엄지 손가락으로 메모리 모듈을 누릅니다. 메모리 모듈이 소켓에 올바르게 장착된 경우 메모리 모듈 소켓의 레버가 메모리 모듈이 설치된 다른 소켓의 레버와 맞춰집니다. 8. 나머지 메모리 모듈을 설치하려면 이 절차의 4-7 단계를 반복합니다. 9. 냉각 덮개를 다시 장착합니다. 10. 시스템을 닫습니다. 11. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 12.
그림 14 . 2.5 인치 하드 드라이브 보호물 분리 및 설치 1. 하드 드라이브 보호물 2. 분리 단추 2.5 인치 하드 드라이브 보호물 설치 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 2. 분리 단추가 제자리에 고정될 때까지 하드 드라이브를 하드 드라이브 슬롯에 삽입합니다. 3. 해당하는 경우 전면 베젤을 설치합니다. 핫 스왑 하드 드라이브 분리 주의: 데이터 손실을 막으려면, 운영 체제가 핫스왑 드라이브 설치를 지원해야 합니다. 운영 체제와 함께 제 공된 설명서를 참조하십시오. 1. 관리 소프트웨어에서 하드 드라이브의 분리를 준비합니다. 하드 드라이브 캐리어의 표시등이 하드 드라이 브를 안전하게 분리할 수 있음을 나타낼 때까지 기다립니다. 자세한 내용은 저장소 컨트롤러의 설명서를 참 조하십시오. 하드 드라이브가 온라인 상태인 경우 드라이브가 꺼진 상태와 같이 녹색 작동/오류 표시등이 점멸됩니다. 하드 드라이브 표시등이 꺼지면 하드 드라이브를 제거할 수 있습니다. 2.
그림 15 . 핫 스왑 하드 드라이브 분리 및 설치 1. 분리 단추 2. 하드 드라이브 3. 하드 드라이브 캐리어 핸들 핫 스왑 하드 드라이브 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 하드 드라이브 후면판에서 사용할 수 있도록 검사 및 승인된 하드 드라이브만 사용하십시오. 주의: 동일한 RAID 볼륨에 SAS 와 SATA 하드 드라이브를 결합하여 사용할 수 없습니다. 주의: 하드 드라이브를 설치할 때 인접 드라이브가 완전히 설치되어 있는지 확인합니다.
하드 드라이브 캐리어에서 하드 드라이브 분리 1. 하드 드라이브 캐리어의 슬라이드 레일에서 나사를 분리합니다. 2. 하드 드라이브 캐리어에서 하드 드라이브를 들어냅니다. 그림 16 . 하드 드라이브 캐리어에서 하드 드라이브 분리 및 설치 1. 하드 드라이브 캐리어 2. 하드 드라이브 3. 나사(4 개) 하드 드라이브 캐리어에 하드 드라이브 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 하드 드라이브 커넥터의 끝이 뒤쪽에 놓이도록 하드 드라이브를 하드 드라이브 캐리어에 삽입합니다. 2.
광학 드라이브 광학 드라이브 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 절차는 8 하드 드라이브 시스템에만 적용됩니다. 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 2. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 3. 시스템을 엽니다. 4. 드라이브의 후면에서 전원/데이터 케이블을 분리합니다. 시스템 보드와 드라이브에서 분리할 때 시스템의 옆에 전원/데이터 케이블을 배선합니다. 케이블이 조이거 나 구겨지지 않도록 케이블을 교체할 때 적절하게 배선해야 합니다. 5.
광학 드라이브 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 절차는 8 하드 드라이브 시스템에만 적용됩니다. 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 2. 시스템 및 장착된 모든 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 3. 시스템을 엽니다. 4. 광학 드라이브를 섀시 전면의 광학 드라이브 슬롯에 맞춥니다. 5. 래치가 제자리에 걸릴 때까지 광학 드라이브를 밀어 넣습니다. 6. 광학 드라이브 및 시스템 보드에 전원/데이터 케이블을 연결합니다. 노트: 케이블이 조이거나 구겨지지 않도록 케이블을 시스템 옆에 제대로 배선해야 합니다.
그림 18 . 냉각 팬 분리 및 설치 1. 냉각 팬 조립품 2. 냉각 팬(7 개) 3. 냉각 팬 커넥터(7 개) 냉각 팬 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템을 엽니다. 2. 냉각 팬의 밑 부분에 있는 플러그를 시스템 보드의 커넥터에 맞춥니다. 3. 탭이 제자리에 고정될 때까지 냉각 팬을 고정 슬롯으로 밀어 넣습니다. 4. 시스템을 닫습니다. 내부 USB 메모리 키(선택사양) 시스템 내부에 설치된 선택적 USB 메모리 키를 부팅 장치, 보안 키 또는 대용량 저장 장치로 사용할 수 있습니다.
내부 USB 키 교체 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 2. 시스템을 엽니다. 3. 시스템 보드에서 USB 커넥터/USB 키를 찾습니다. USB 커넥터(J_USB_INT)를 찾으려면 시스템 보드 커넥터를 참조하십시오. 4. USB 키가 설치되어 있으면 USB 키를 분리합니다. 5. USB 커넥터에 USB 키를 삽입합니다. 6. 시스템을 닫습니다. 7. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 8.
표 3. 지원되는 확장 카드 라이저 PCIe 슬롯 프로세서 연결 높이 길이 링크 폭 슬롯 폭 2 1 프로세서 1 로우 프로파일 절반 길이 x8 x16 프로세서 2 로우 프로파일 절반 길이 x16 x16 프로세서 1 전체 높이 3/4 길이 x16 x16 3 2 주의: 10GbE 네트워크 도터 카드가 설치되어 있는 경우 GPU 카드를 설치할 수 없습니다. 노트: 라이저 3 의 PCIe 확장 카드 슬롯(슬롯 2)에 대해 3/4 길이 GPU 카드만 지원됩니다. 노트: 라이저 2 에 있는 하나의 슬롯에만 확장 카드를 설치할 수 있습니다. 노트: 라이저 2 슬롯에서 x16 링크를 사용하려면 두 프로세서를 모두 설치해야 합니다. 다음 표에서는 냉각 및 기계적 설치가 올바르게 수행되도록 확장 카드를 설치하는 지침을 제공합니다. 표시된 슬롯 우선 순위를 사용하여 우선 순위가 가장 높은 확장 카드를 먼저 설치해야 합니다.
노트: 시스템의 미국 연방 통신위원회(FCC) 인증을 유지하려면 필러 브래킷을 빈 확장 슬롯에 설치해야 합 니다. 브래킷은 또한 시스템 안으로 먼지 및 이물질이 들어오는 것을 막고 시스템 내부의 적절한 냉각 및 공 기 흐름을 도와줍니다. 7. 시스템을 닫습니다. 8. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 그림 20 . 확장 카드 분리 및 설치 1. 확장 카드 2. 확장 카드 커넥터 3. 확장 카드 래치 확장 카드 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 확장 카드의 포장을 풀고 설치를 준비합니다.
10. 시스템을 닫습니다. 11. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 12. 카드 설명서에 설명된 대로 카드에 필요한 모든 장치 드라이버를 설치합니다. 확장 카드 라이저 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 두 프로세서가 모두 설치되어 있는 경우에만 라이저 2 슬롯에서 확장 카드 라이저 1 및 x16 링크를 사 용할 수 있습니다. 1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 2. 시스템을 엽니다. 3.
그림 22 . 확장 카드 라이저 3 분리 및 설치 1. 커넥터 2. 확장 카드 라이저 3 4. 해당하는 경우 라이저에 확장 카드를 설치하거나 분리합니다. 5. 확장 카드 라이저를 교체합니다. 6. 시스템을 닫습니다. 7. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 확장 카드 라이저 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 해당하는 경우 확장 카드를 확장 카드 라이저에 다시 설치합니다. 2. 확장 카드 라이저를 시스템 보드의 커넥터와 라이저 가이드 핀에 맞춥니다. 3.
SD vFlash 카드 교체 노트: 이 절차는 8 하드 드라이브 시스템에만 적용됩니다. 1. 시스템에서 vFlash 미디어 슬롯을 찾습니다. 2. 설치된 SD vFlash 카드를 분리하려면 카드를 안쪽으로 밀어 분리합니다. 3. 카드 슬롯에서 카드를 당겨 빼냅니다. 그림 23 . SD vFlash 카드 분리 및 설치 1. SD vFlash 카드 2. SD vFlash 카드 슬롯 4. SD vFlash 카드를 설치하려면 레이블이 위로 향한 상태로 모듈의 카드 슬롯에 SD 카드의 접촉 핀 끝을 삽입 합니다. 노트: 슬롯은 카드를 올바르게 삽입할 수 있도록 설계되어 있습니다. 5. 카드를 슬롯 안쪽으로 눌러 고정합니다. 내부 이중 SD 모듈 노트: 시스템 설치 프로그램의 Integrated Devices(내장형 장치) 화면에서 Redundancy(중복성) 옵션이 Mirror Mode(미러 모드)로 설정된 경우 SD 카드 간에 정보가 복제됩니다.
7. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 그림 24 . 내부 이중 SD 모듈 분리 및 설치 1. 2. 3. 4. 5. 파란색 당김 탭 SD 카드 1 SD 카드 2 이중 SD 모듈 시스템 보드의 커넥터 내부 이중 SD 모듈 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 2. 시스템을 엽니다. 3. 시스템 보드에서 J_RIPS 커넥터를 찾습니다. 4. 시스템 보드의 커넥터와 이중 SD 모듈을 맞춥니다. 5.
7. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 내부 SD 카드 내부 SD 카드 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 2. 시스템을 엽니다. 3. 후면판 확장 보드 또는 내부 이중 SD 모듈에서 SD 카드 슬롯을 찾은 다음 카드를 안쪽으로 눌러 슬롯에서 분 리하고 카드를 분리합니다. 4. 시스템을 닫습니다. 5. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다.
내장형 저장소 컨트롤러 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 모든 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 2. 시스템을 엽니다. 3. 카드의 모서리에 있는 두 개의 탭을 아래로 누르고 추출기에서 카드를 들어 올립니다. 4. 시스템 보드의 저장소 컨트롤러 카드 홀더에서 카드의 다른 쪽 끝이 분리되도록 카드의 각도를 맞춥니다. 5. 시스템을 닫습니다. 고정 격리 애자에서 카드가 분리되면 카드 아래의 커넥터가 시스템 보드 커넥터에서 분리됩니다. 1. 시스템 보드의 저장소 커넥터 2. 저장소 컨트롤러 카드 3.
내장형 저장소 컨트롤러 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 모든 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 2. 시스템을 엽니다. 3. 카드의 한쪽 끝을 시스템 보드의 카드 홀더에 맞춥니다. 4. 카드의 다른 쪽 끝을 아래로 내리고 카드에 있는 구멍을 시스템 보드에 있는 추출기의 위치 기둥과 맞춥니 다. 5. 완전히 장착될 때까지 모서리에서 카드를 아래로 누릅니다. 카드가 완전히 장착되면 플라스틱 고정 격리 애자 탭이 홀더의 모서리에 끼워집니다. 6. 시스템을 닫습니다. 7.
그림 25 . 네트워크 도터 카드 분리 및 설치 1. 2. 3. 4. 조임 나사 소켓(2 개) 시스템 보드의 커넥터 조임 나사(2 개) 접촉점 5. 네트워크 도터 카드 6. RJ-45 커넥터의 후면 패널 슬롯 네트워크 도터 카드 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 10Gb 네트워크 도터 카드를 설치하는 경우 시스템에 네트워크 도터 카드 냉각 덮개가 설치되어 있는 지 확인합니다. 1. 후면 패널의 슬롯을 통과하여 RJ-45 커넥터가 맞춰지도록 카드의 각도를 맞춥니다. 2.
• 프로세서 장착 노트: 적절한 시스템 냉각 상태를 유지하려면 빈 프로세서 소켓에 프로세서 보호물 및 방열판 보호물을 설 치해야 합니다. 프로세서 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템을 업그레이드하기 전에 support.dell.com 에서 최신 버전의 시스템 BIOS 를 다운로드한 다음 압축된 다운로드 파일에 포함된 지침에 따라 시스템에 업데이트를 설치합니다. 노트: Lifecycle Controller 를 사용하여 시스템 BIOS 를 업데이트할 수 있습니다. 2. 시스템 및 장착된 주변 장치를 모두 끄고 콘센트에서 시스템을 분리합니다.
그림 26 . 방열판 분리 및 설치 1. 2. 3. 4. 방열판 고정 소켓(2 개) 고정 나사(2 개) 프로세서 주의: 강한 힘으로 프로세서를 해당 소켓에 고정해야 합니다. 단단히 잡지 않으면 분리 레버가 갑자기 튕겨 나올 수 있습니다. 8. 9. 66 잠금 해제 아이콘 근처에 있는 프로세서 소켓 분리 레버 위에 엄지 손가락을 올려놓습니다. 래로 누르고 탭 아래에서 떼어 내어 잠금 위치에서 분리합니다. 레버를 아 마찬가지로, 잠금 아이콘 근처에 있는 프로세서 소켓 분리 레버 위에 엄지 손가락을 올려놓습니다. 레 버를 아래로 누르고 탭 아래에서 떼어 내어 잠금 위치에서 분리합니다. 레버를 위쪽으로 90 도 회전합니다.
그림 27 . 프로세서 실드 레버 열기 및 닫기 시퀀스 1. 2. 3. 4. 5. 폐쇄-잠금 기호 프로세서 소켓 분리 레버 프로세서 프로세서 소켓 분리 레버 개방-잠금 기호 10. 프로세서 실드를 위로 돌려 꺼냅니다. 주의: 소켓 핀은 부러지기 쉽고 영구적으로 손상될 수 있습니다. 프로세서를 소켓에서 분리하는 경우, 소켓 의 핀이 구부러지지 않게 주의하십시오. 11. 프로세서를 소켓에서 들어 꺼내고 분리 레버를 위로 올린 상태로 두어 소켓에 새 프로세서를 설치할 수 있 도록 준비합니다. 노트: 프로세서를 영구적으로 분리하는 경우 프로세서 보호물과 방열판 보호물을 빈 소켓에 설치하여 적절 한 시스템 냉각 상태를 유지해야 합니다. 노트: 프로세서 보호물/방열판 보호물을 설치하는 방법은 프로세서/방열판을 설치하는 경우와 동일합니 다.
그림 28 . 프로세서 분리 및 설치 1. 2. 3. 4. 5. 프로세서 소켓 분리 레버 핀 1 표시등 프로세서 소켓 분리 레버 프로세서 실드 프로세서 6. ZIF 소켓 7. 소켓 키(4 개) 8. 프로세서의 노치(4 개) 노트: 프로세서를 분리한 후 재사용, 반환 또는 임시 저장을 위해 정전기 방지 컨테이너에 보관합니다. 프로 세서의 아래쪽을 건드리지 마십시오. 프로세서의 측면 모서리만 잡으십시오. 프로세서 소켓 2 에서 프로세 서를 분리하는 경우 비어 있는 소켓에 방열판 보호물을 설치해야 합니다. 프로세서 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오.
4. 냉각 덮개를 분리합니다. 경고: 방열판과 프로세서는 시스템 전원을 끈 후에도 얼마 동안 뜨거울 수 있습니다. 방열판과 프로세서를 다루기 전에 냉각될 때까지 기다리십시오. 주의: 프로세서를 제거할 의도가 아니라면 프로세서에서 방열판을 제거하지 마십시오. 방열판은 적절한 열 상태를 유지하는데 필요합니다. 5. 방열판/방열판 보호물 및 프로세서/프로세서 방열판을 분리합니다(해당되는 경우). 노트: 방열판 보호물 또는 프로세서 보호물을 분리하는 절차는 방열판 또는 프로세서를 분리하는 절차와 유사합니다. 6. 새 프로세서의 포장을 풉니다. 7. 프로세서를 ZIF 소켓의 소켓 키에 맞춥니다. 주의: 프로세서를 잘못 위치시키면 시스템 보드 또는 프로세서에 영구적인 손상을 입힐 수 있습니다. 소켓 의 핀이 구부러지지 않도록 주의하십시오. 주의: 프로세서를 장착하는데 너무 많은 힘을 가하지 마십시오. 프로세서가 올바르게 위치하면 소켓에 쉽 게 장착됩니다. 8.
주의: 1100W AC 또는 DC PSU 를 설치하는 경우 두 PSU 를 모두 설치해야 합니다. 시스템에서는 1100W AC 또 는 DC PSU 를 모두 지원합니다. 핫 스페어 기능 시스템은 전원 공급 장치 중복과 관련된 전력 오버헤드를 크게 줄여 주는 핫 스페어 기능을 지원합니다. 핫 스페어 기능이 활성화되어 있으면 중복되는 전원 공급 장치가 슬립 상태로 전환됩니다. 활성 전원 공급 장치 가 부하의 100%를 지원하므로 보다 효율적으로 작동하게 됩니다. 중복되는 전원 공급 장치는 슬립 상태에 있는 동안 활성 전원 공급 장치의 출력 전압을 모니터링합니다. 활성 전원 공급 장치의 출력 전압이 떨어지면 슬립 상 태에 있는 중복되는 전원 공급 장치가 활성 출력 상태로 되돌아갑니다. 중복되는 전원 공급 장치를 슬립 상태에 두는 것보다 두 전원 공급 장치 모두 활성 상태에 있는 것이 더 효율적이 면 활성 전원 공급 장치가 슬립 상태의 전원 공급 장치를 활성화할 수도 있습니다.
1. 2. 3. 4. 커넥터 전원 공급 장치 분리 래치 전원 공급 장치 핸들 AC 전원 공급 장치 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 두 전원 공급 장치의 유형과 최대 출력 전력이 동일한지 확인합니다. 노트: 최대 출력 전력(와트 단위로 표기)은 전원 공급 장치 레이블에 표시되어 있습니다. 2. 해당하는 경우 전원 공급 장치 보호물을 분리합니다. 3. 분리 래치가 제자리에 장착되어 전원 공급 장치가 완전히 고정될 때까지 새 전원 공급 장치를 섀시에 밀어 넣습니다. 노트: 케이블 관리대의 래치를 벗긴 경우 다시 래치를 고정합니다.
키트 내용물 • Dell 부품 번호 6RYJ9 단자대 또는 이와 동등한 부품(1 개) • 잠금 와셔가 장착된 #6-32 너트(1 개) 필요한 도구 10 AWG 크기의 단선 또는 연선 절연 구리선으로부터 절연체를 제거할 수 있는 와이어 스트리퍼 펜치 노트: 알파 와이어 부품 번호 3080 또는 이와 동등한 부품 사용(65/30 연선) 필요한 와이어 • UL 10 AWG, 최대 2m(연선) 검정색 와이어 1 개 [–(48–60)V DC] • UL 10 AWG, 최대 2m(연선) 빨간색 와이어 1 개 (V DC 리턴) • UL 10 AWG, 최대 2m 녹색/노란색, 노란색 줄이 있는 녹색, 연선 와이어(안전 접지) 안전 접지선 조립 및 연결 경고: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격이 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오.
1. 2. 3. 4. 5. 안전 접지선 접지 기둥 잠금 와셔 스프링 와셔 #6-32 너트 DC 입력 전선 조립 경고: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격이 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모 든 전기 배선은 해당 로컬 또는 국가 코드와 규칙을 준수해야 합니다. Dell 의 승인을 받지 않은 서비스 작업 으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 구리선이 약 13mm(0.5 인치) 노출되도록 DC 전선 끝에 있는 피복을 벗겨 냅니다. 경고: DC 전선을 연결할 때 극성을 서로 바꾸면 전원 공급 장치 또는 시스템이 영구적으로 손상될 수 있습니 다. 2. 구리선의 양쪽 끝을 메이팅 커넥터에 삽입하고 #2 십자 드라이버를 사용하여 메이팅 커넥터의 상단에 있는 조임 나사를 조입니다.
DC 전원 공급 장치 분리 경고: -48 ~ 60V DC 전원 공급 장치를 사용하는 장비의 경우 자격이 있는 전기 기사가 DC 전원 및 안전 접지에 대한 모든 연결을 수행해야 합니다. 직접 DC 전원에 연결하거나 접지를 설치하도록 시도하지 마십시오. 모 든 전기 배선은 해당 로컬 또는 국가 코드와 규칙을 준수해야 합니다. Dell 의 승인을 받지 않은 서비스 작업 으로 인한 손상에 대해서는 보상을 받을 수 없습니다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 시스템이 정상적으로 작동하려면 하나의 전원 공급 장치가 필요합니다. 중복 시스템의 전원이 켜져 있는 경우 전원이 켜져 있는 시스템에서 전원 공급 장치를 한 번에 하나만 분리하고 교체합니다. 노트: 전원 공급 장치를 분리하는 데 방해가 되는 경우 선택적 케이블 관리 암을 풀고 들어 올려야 할 수도 있습니다. 케이블 관리 암에 대한 자세한 내용은 시스템의 랙 설명서를 참조하십시오. 1.
노트: 최대 출력 전원(와트 단위로 표기)은 전원 공급 장치 레이블에 표시되어 있습니다. 2. 해당하는 경우 전원 공급 장치 보호물을 분리합니다. 3. 분리 래치가 제자리에 장착되어 전원 공급 장치가 완전히 고정될 때까지 새 전원 공급 장치를 섀시에 밀어 넣습니다. 노트: 케이블 관리 암의 래치를 분리한 경우 래치를 다시 장착합니다. 케이블 관리 암에 대한 자세한 내용은 시스템의 랙 설명서를 참조하십시오. 4. 안전 접지선을 연결합니다. 5. 전원 공급 장치에 DC 전원 커넥터를 설치합니다. 주의: 전선을 연결할 때 안전 끈을 사용하여 전원 공급 장치 핸들에 전선을 고정합니다. 6. DC 전원에 전선을 연결합니다. 노트: 새 전원 공급 장치를 설치, 핫 스왑 또는 핫 애드하는 경우 시스템이 전원 공급 장치를 인식하고 상태 를 확인할 때까지 몇 초 동안 기다리십시오. 전원 공급 장치가 올바르게 작동할 경우 전원 공급 장치 상태 표시등이 녹색으로 켜집니다.
시스템 배터리 시스템 배터리 교체 경고: 새 배터리를 잘못 설치하면 폭발할 수 있습니다. 배터리를 교체할 때에는 제조업체가 권장하는 것과 동일하거나 동등한 종류의 배터리 만을 사용하십시오. 추가 정보는 안전 정보를 참조하십시오. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 2. 시스템을 엽니다. 3. 접촉점을 누르고 시스템 배터리 덮개를 들어 올려 네트워크 도터 카드 냉각 덮개에서 분리합니다. 그림 34 . 시스템 배터리 분리 1. 시스템 배터리 덮개 2.
그림 35 . 시스템 배터리 교체 1. 배터리 커넥터의 양극 쪽 2. 시스템 배터리 3. 배터리 커넥터의 음극 쪽 6. 새 시스템 배터리를 설치하려면 "+"가 위로 향하게 배터리를 잡고 커넥터 양극 쪽의 고정 탭 아래로 밉니다. 7. 배터리가 제자리에 끼워질 때까지 똑바로 커넥터 안으로 누릅니다. 8. 시스템 배터리 덮개의 뒷면을 네트워크 도터 카드 냉각 덮개에 있는 노치에 맞추고 시스템 배터리 덮개가 제자리에 끼워질 때까지 노치 쪽으로 아래로 누릅니다. 9. 시스템을 닫습니다. 10. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 11. 시스템 설치 프로그램을 시작하여 배터리가 올바르게 작동하는지 확인합니다. 12. 시스템 설정의 Time(시간) 및 Date(날짜) 필드에 정확한 시간 및 날짜를 입력합니다. 13. 시스템 설치 프로그램을 종료합니다. 하드 드라이브 후면판 시스템은 2.5 인치 (x4) SAS/SATA 후면판을 지원합니다.
5. 후면판에서 SAS/SATA/SSD 데이터 케이블 및 전원 케이블을 분리합니다. 6. 해당하는 경우 광 드라이브에서 전원/데이터 케이블을 분리합니다. 7. 화살표 방향으로 파란색 분리 탭을 누르고 후면판을 위로 들어 올립니다. 8. 후면판에 있는 고정 슬롯이 섀시에 있는 탭에서 분리될 때까지 시스템에서 후면판을 당겨 빼냅니다. 그림 36 . 2.5 인치 (x4) 하드 드라이브 후면판 분리 및 설치 1. 2. 3. 4. 5.
그림 37 . 케이블 연결 다이어그램 - 2.5 인치 (x4) 시스템 1. 2. 3. 4. 5. 케이블 고정 브래킷 시스템 보드 내장형 저장소 컨트롤러 카드 시스템 보드의 SAS 커넥터 SAS 후면판 하드 드라이브 후면판 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 파란색 탭을 잡은 상태로 하드 드라이브 후면판에 있는 슬롯을 섀시에 있는 탭에 맞춥니다. 2. 분리 탭이 제자리에 끼워질 때까지 하드 드라이브 후면판을 아래로 밉니다. 3.
9. 해당하는 경우 전면 베젤을 설치합니다. 제어판 조립품 제어판 보드 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 2. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 3. 시스템을 엽니다. 주의: 디스플레이 모듈 커넥터는 ZIF(zero insertion force) 커넥터입니다. 제거 및 삽입을 수행하기 전에 커넥 터의 잠금 탭이 분리되어 있는지 확인합니다. 삽입한 후 잠금 탭을 연결해야 합니다. 4. 제어판 보드에서 제어판 및 디스플레이 모듈 케이블을 분리합니다.
제어판 보드 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 제어판 보드의 나사 구멍을 섀시의 고정 격리 애자에 맞춥니다. 2. #2 십자 드라이버를 사용하여 제어판 보드를 섀시에 고정하는 두 개의 나사를 교체합니다. 주의: 디스플레이 모듈 커넥터는 ZIF(zero insertion force) 커넥터입니다. 제거 및 삽입을 수행하기 전에 커넥 터의 잠금 탭이 분리되어 있는지 확인합니다. 삽입한 후 잠금 탭을 연결해야 합니다. 3. 제어판 보드에 제어판 및 디스플레이 모듈 케이블을 연결합니다. 4. 필요한 경우 섀시 벽을 따라 전원/데이터 케이블을 배선합니다.
그림 39 . 제어판 분리 및 설치 1. 콘솔 2. 섀시 전면 벽의 노치 3. 디스플레이 모듈 ZIF 커넥터 4. 디스플레이 모듈 케이블 5. 나사 제어판 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 제어판의 왼쪽을 섀시로 밀어 제어판의 왼쪽 탭을 섀시 벽의 슬롯에 맞추고 왼쪽 상단 탭을 섀시 상단의 슬 롯에 맞춥니다. 2. 디스플레이 모듈 케이블을 입구를 관통하여 섀시 쪽으로 당깁니다. 3. 오른쪽 상단 탭이 섀시의 상단에 맞춰지고 패널이 제자리에 끼워질 때까지 제어판의 오른쪽을 밉니다. 4.
VGA 모듈 VGA 모듈 분리 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 이 절차는 8 하드 드라이브 시스템에만 적용됩니다. 1. 설치되어 있는 경우 전면 베젤을 분리합니다. 2. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트 및 주변 장치에서 분리합니다. 3. 시스템을 엽니다. 주의: 디스플레이 모듈 커넥터는 ZIF(zero insertion force) 커넥터입니다. 제거 및 삽입을 수행하기 전에 커넥 터의 잠금 탭이 분리되어 있는지 확인합니다. 삽입한 후 잠금 탭을 연결해야 합니다. 4. 제어판 보드에서 디스플레이 모듈 케이블을 분리합니다. 5.
VGA 모듈 설치 노트: 이 절차는 8 하드 드라이브 시스템에만 적용됩니다. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. VGA 모듈을 섀시로 밀고 VGA 모듈의 나사 구멍을 섀시의 나사 구멍에 맞춥니다. 2. #2 십자 드라이버를 사용하여 섀시에 VGA 모듈을 고정하는 섀시의 맨 아래에 있는 나사를 교체합니다. 3. 제어판을 교체합니다. 4. VGA 모듈 케이블을 VGA 모듈에 연결합니다. 주의: 디스플레이 모듈 커넥터는 ZIF(zero insertion force) 커넥터입니다. 제거 및 삽입을 수행하기 전에 커넥 터의 잠금 탭이 분리되어 있는지 확인합니다.
g) h) i) j) k) l) 모든 확장 카드 및 내장형 저장소 컨트롤러 카드 네트워크 도터 카드 내부 이중 SD 모듈 내부 USB 키(설치된 경우) 핫 스왑 하드 드라이브 하드 드라이브 후면판 주의: 미니 SAS 케이블 및 커넥터가 손상되지 않도록 하려면 시스템 보드에서 미니 SAS 케이블을 분리할 때 올바른 절차를 따르십시오. 5. 시스템 보드에서 미니 SAS 케이블을 분리합니다. a) 미니 SAS 케이블 커넥터를 밀어 시스템 보드의 (J_SASX8) 커넥터 쪽으로 더 멀리 밀어냅니다. b) 미니 SAS 케이블 커넥터에 있는 금속 탭을 누른 상태로 유지합니다. c) 미니 SAS 케이블을 당겨 시스템 보드의 커넥터에서 빼냅니다. a. 미니 SAS 케이블 커넥터 b. 금속 탭 6. c. 시스템 보드의 커넥터 시스템 보드에서 다른 모든 케이블을 분리합니다. 주의: 섀시에서 시스템 보드를 분리하는 동안 시스템 식별 단추가 손상되지 않도록 주의하십시오. 7.
그림 41 . 시스템 보드 분리 및 설치 1. 시스템 보드 2. 시스템 보드 홀더 3. 분리 핀 시스템 보드 설치 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 새 시스템 보드 조립품의 포장을 풉니다. 주의: 메모리 모듈, 프로세서 또는 그 밖의 구성요소를 잡고 시스템 보드 조립품을 들어 올리지 마십시오. 주의: 시스템 보드를 섀시에 배치하는 동안 시스템 식별 단추가 손상되지 않도록 주의하십시오. 2. 접촉점을 잡고 시스템 보드를 섀시 쪽으로 아래로 내립니다. 3. 보드가 제자리에 고정될 때까지 섀시 후면 방향으로 시스템 보드를 밉니다. 4.
l) 냉각 덮개 5. 시스템 보드 조립품, SAS 후면판, 제어판 보드 및 광학 드라이브(해당하는 경우)에 케이블을 연결합니다. 6. 섀시 벽을 따라 전원/데이터 케이블을 배선합니다. 7. 시스템을 닫습니다. 8. 해당하는 경우 전면 베젤을 설치합니다. 9. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 10. 신규 또는 기존 iDRAC Enterprise 라이센스를 가져옵니다. 자세한 내용은 iDRAC7 사용 설명서 (support.dell.com/manuals)를 참조하십시오.
4 시스템 문제 해결 안전 제일 - 사용자 및 시스템 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 시스템 시작 오류 문제 해결 UEFI 부팅 관리자에서 운영 체제를 설치한 후 시스템을 BIOS 부팅 모드로 부팅하면 시스템이 중지됩니다. 그 반 대의 경우에도 마찬가지입니다. 운영 체제를 설치한 동일한 부팅 모드로 부팅해야 합니다. 기타 모든 시작 문제는 화면에 표시되는 시스템 메시지를 참고하십시오. 외부 연결 문제 해결 외부 장치의 문제를 해결하기 전에 모든 외부 케이블이 시스템의 외부 커넥터에 안전하게 연결되어 있는지 확인 하십시오. 비디오 하위 시스템 문제 해결 1.
8. 시스템을 다시 시작하고 키보드가 작동하는 경우 시스템 설치 프로그램을 시작합니다. Integrated Devices(내장형 장치) 화면의 System Setup(시스템 설치) 옵션에서 모든 USB 포트가 활성화되어 있는지 확인 합니다. 키보드가 작동하지 않는 경우 원격 액세스를 사용할 수도 있습니다. 시스템에 액세스할 수 없는 경우 시스 템 내의 NVRAM_CLR 점퍼를 재설정하고 BIOS 를 기본 설정으로 복원합니다. 9. 각 USB 장치를 한 번에 하나씩 다시 연결하고 전원을 켭니다. 10. 장치에 동일한 문제가 발생하면 해당 장치의 전원을 끄고 USB 케이블을 상태가 양호한 케이블로 교체한 후 장치의 전원을 켭니다. 문제를 해결할 수 없는 경우 도움말 얻기를 참조하십시오. 직렬 I/O 장치 문제 해결 1. 2. 시스템 및 직렬 포트에 연결된 모든 주변 장치를 끕니다. 직렬 인터페이스 케이블을 올바르게 작동하는 케이블로 교체하고 시스템 및 직렬 장치를 켭니다.
1. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 2. 시스템을 엽니다. 3. 시스템에서 다음 구성부품을 분해합니다. – 하드 드라이브 – 하드 드라이브 후면판 – USB 메모리 키 – 냉각 덮개 – 확장 카드 라이저(있는 경우) – 확장 카드 – 전원 공급 장치 – 냉각 팬 어셈블리(있는 경우) – 냉각 팬 – 프로세서 및 방열판 4. – 메모리 모듈 최소한 하루 이상 시스템을 건조시킵니다. 5. 3 단계에서 분리한 구성부품을 다시 설치합니다. 6. 시스템을 닫습니다. 7. 시스템 및 장착된 주변 장치의 전원을 켭니다. 8. 시스템이 올바르게 시작되면 시스템을 종료하고 분리한 모든 확장 카드를 다시 설치합니다. 9. 적절한 진단 검사를 실행합니다. 자세한 내용은 '시스템 진단 프로그램 사용'을 참조하십시오. 시스템이 제대로 시작되지 않으면 도움말 얻기를 참조하십시오. 검사가 실패하면 도움말 얻기를 참조하십시오.
5. 시스템을 닫습니다. 6. 적절한 진단 검사를 실행합니다. 자세한 내용은 '시스템 진단 프로그램 사용'을 참조하십시오. 검사가 실패하면 도움말 얻기를 참조하십시오. 시스템 배터리 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 노트: 장기간(몇 주 또는 몇 달) 시스템을 사용하지 않을 경우 NVRAM 의 시스템 구성 정보가 손실될 수 있습 니다. 이 문제는 배터리에 결함이 있는 경우 발생합니다. 1. 시스템 설치 프로그램을 통해 시간 및 날짜를 다시 입력합니다. 2. 시스템을 끄고 최소 한 시간 동안 콘센트에서 시스템을 분리한 상태로 둡니다. 3.
• 냉각 팬이 분리되었거나 오류가 발생했습니다. • 확장 카드 설치 지침을 따르지 않았습니다. 냉각 팬 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템을 엽니다. 2. 팬 또는 팬의 전원 케이블을 다시 장착합니다. 3. 팬이 올바르게 작동하면 시스템을 닫습니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 시스템 메모리 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다.
14. 시스템을 닫습니다. 15. 시스템이 부팅할 때 표시되는 오류 메시지 및 시스템 전면의 진단 표시등을 확인합니다. 16. 계속해서 메모리 문제가 나타나면 설치된 각 메모리 모듈에 대해 12 단계에서 15 단계를 반복하십시오. 모든 메모리 모듈을 검사한 후에도 문제가 지속되면 도움말 얻기를 참조하십시오. 내부 USB 키 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 설치 프로그램을 시작하고 Integrated Devices(내장형 장치) 화면에서 USB 키 포트가 활성화되어 있 는지 확인합니다. 2.
7. 새 SD 카드를 SD 카드 슬롯 2 에 삽입합니다. 8. 시스템을 닫습니다. 9. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 모두 켭니다. 10. 시스템 설치 프로그램을 시작하고 Internal SD Card Port(내부 SD 카드 포트) 및 Internal SD Card Redundancy(내부 SD 카드 중복성) 모드가 활성화되어 있는지 확인합니다. 11. SD 카드가 올바로 작동하는지 확인합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 광학 드라이브 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1.
문제를 해결할 수 없는 경우 도움말 얻기를 참조하십시오. 하드 드라이브 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 주의: 이 문제 해결 절차를 수행하면 하드 드라이브에 저장된 데이터가 삭제될 수 있습니다. 계속하기 전에 하드 드라이브에 있는 모든 파일을 백업하십시오. 1. 적절한 진단 검사를 실행합니다. 자세한 내용은 '시스템 진단 프로그램 사용'을 참조하십시오. 진단 검사 결과에 따라 필요한 경우 다음 단계를 수행합니다. 2. 시스템에 RAID 컨트롤러가 있고 하드 드라이브가 RAID 배열로 구성되어 있는 경우 다음 단계를 수행하십시 오.
12. 시스템을 콘센트에 다시 연결하고 시스템 및 장착된 주변 장치를 켭니다. 13. 적절한 진단 검사를 실행합니다. 자세한 내용은 시스템 진단 프로그램 사용을 참조하십시오. 검사에 실패 한 경우 도움말 얻기를 참조하십시오. 14. 10 단계에서 분리한 각 확장 카드에 대해 다음 단계를 수행합니다. a. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. b. 시스템을 엽니다. c. 확장 카드 중 하나를 다시 설치합니다. d. 시스템을 닫습니다. e. 적절한 진단 검사를 실행합니다. 자세한 내용은 '시스템 진단 프로그램 사용'을 참조하십시오. 검사가 실패하면 도움말 얻기를 참조하십시오. 확장 카드 문제 해결 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다.
1. 적절한 진단 검사를 실행합니다. 수행 가능한 진단 검사에 대해서는 시스템 진단 프로그램 사용을 참조하십 시오. 2. 시스템 및 장착된 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 3. 시스템을 엽니다. 4. 프로세서 및 방열판이 올바르게 설치되어 있는지 확인합니다. 5. 시스템을 닫습니다. 6. 적절한 진단 검사를 실행합니다. 자세한 내용은 시스템 진단 프로그램 사용을 참조하십시오. 문제가 계속해서 나타나면 도움말 얻기를 참조하십시오.
5 시스템 진단 프로그램 사용 시스템에 문제가 발생하면 기술 지원에 문의하기 전에 시스템 진단 프로그램을 실행합니다. 진단 프로그램은 추 가 장비 없이 또는 데이터를 유실할 위험 없이 시스템 하드웨어를 검사하기 위해 실행됩니다. 자체적으로 문제 를 해결할 수 없는 경우에는 서비스 및 지원 담당 직원이 진단 검사 결과를 사용하여 문제 해결을 지원할 수 있습 니다. Dell Online Diagnostics Dell Online Diagnostics 는 진단 프로그램 또는 검사 모듈로 구성된 독립형 제품군이며 사용자는 이 제품군을 사 용하여 프로덕션 환경에서 시스템에 대한 진단 검사를 실행하고, 시스템의 최대 가동 시간을 확보할 수 있습니 다. Online Diagnostics 를 사용하면 섀시 및 저장 구성부품(예: 하드 드라이브, 실제 메모리 및 NIC(네트워크 인터 페이스 카드))에 대해 진단 검사를 실행할 수 있습니다.
1. 시스템 부팅 시 키를 누릅니다. 2. 위쪽 및 아래쪽 화살표 키를 사용하여 System Utilities(시스템 유틸리티) → Launch Dell Diagnostics(Dell 진단 프로그램 시작)을 선택합니다. ePSA Pre-boot System Assessment(향상된 사전 부팅 시스템 평가) 창이 표시되고, 시스템에서 감지된 모든 장치가 이 창에 나열됩니다. 진단 프로그램은 감지된 모든 장치에 대해 검사를 실행하기 시작합니다. System Diagnostic Controls(시스템 진단 제어) 메뉴 설명 Configuration(구성) 감지된 모든 장치의 구성 및 상태 정보를 표시합니다. Results(결과) 실행된 모든 검사의 결과를 표시합니다. System Health(시스템 상태) 시스템 상태에 대한 현 시점의 개요를 제공합니다. Event Log(이벤트 로그) 시스템에서 실행된 모든 테스트의 결과를 타임스탬프와 함께 보여 주는 로그를 표 시합니다.
6 점퍼 및 커넥터 시스템 보드 점퍼 설정 암호 점퍼를 재설정하여 암호를 비활성화하는 방법에 대한 자세한 내용은 '잊은 암호 비활성화'를 참조하십시 오. 표 5. 시스템 보드 점퍼 설정 점퍼 PWRD_EN 설정 설명 (기본값) 암호 기능이 활성화됩니다(핀 4–6). 암호 기능이 비활성화됩니다(핀 2-4). iDRAC 로컬 액세 스의 잠금이 다음 AC 전원 주기에서 해제됩니다. NVRAM_CLR (기본값) 시스템 부팅 시 구성 설정이 유지됩니다(핀 1-3). 다음 시스템 부팅 시 구성 설정이 지워집니다(핀 3-5).
시스템 보드 커넥터 그림 42 .
항목 커넥터 설명 11 J_VIDEO_REAR 비디오 커넥터 12 J_COM1 직렬 커넥터 13 J_IDRAC_RJ45 iDRAC7 커넥터 14 J_CYC 시스템 식별 커넥터 15 CYC_ID 시스템 식별 단추 16 J_RISER_2A 라이저 2 커넥터 17 J_RISER_1A 라이저 1 커넥터 18 접촉점 시스템 보드를 보관하기 위한 접촉점 19 J_RISER_2B 라이저 2 커넥터 20 J_RISER_1B 라이저 1 커넥터 21 J_STORAGE 저장소 컨트롤러 카드 커넥터 22 J_SASX8 SATA 커넥터 23 J_USB_INT 내부 USB 커넥터 24 BAT 배터리 커넥터 25 CPU2 프로세서 소켓 2 26 B1, B5, B9, B2, B6, B10 메모리 모듈 소켓 27 J_FAN2U_7 냉각 팬 커넥터 28 J_FAN2U_6 냉각 팬 커넥터 29 J_FAN2U_5 냉각 팬 커넥터 30
잊은 암호 비활성화 시스템의 소프트웨어 보안 기능에는 시스템 암호 및 설정 암호가 포함됩니다. 암호 점퍼를 사용하면 이러한 암 호 기능을 활성화하거나 비활성화하고 현재 사용 중인 암호를 지울 수 있습니다. 주의: 대부분의 컴퓨터 관련 수리는 인증받은 서비스 기술자가 수행해야 합니다. 문제 해결이나 간단한 수 리에 한해 제품 문서에 승인된 대로 또는 온라인/전화 서비스 및 지원팀이 안내하는 대로 사용자가 직접 처 리할 수 있습니다. Dell 의 승인을 받지 않은 서비스 작업으로 인한 손상에 대해서는 보상을 받을 수 없습니 다. 제품과 함께 제공된 안전 지침을 읽고 따르십시오. 1. 시스템 및 장착된 모든 주변 장치를 끄고 시스템을 콘센트에서 분리합니다. 2. 시스템을 엽니다. 3. 시스템 보드 점퍼의 점퍼를 핀 4 및 6 에서 핀 2 및 4 로 이동합니다. 4. 시스템을 닫습니다. 점퍼가 핀 2 및 4 에 있는 상태에서 시스템을 부팅할 때까지 기존 암호가 비활성화되거나 지워지지 않습니 다.
7 기술 사양 프로세서 프로세서 종류 Intel Xeon 프로세서 E5-2600 제품군 1 개 또는 2 개 확장 버스 버스 유형 PCI Express Generation 3 라이저 카드를 사용하는 확장 슬롯: 라이저 1 (슬롯 1) 절반 높이, 절반 길이 x8 링크 1 개 (슬롯 2) 절반 높이, 절반 길이 x16 링크 1 개 라이저 2 (슬롯 1) 절반 높이, 절반 길이 x8 링크 1 개 또는 절반 높이, 절반 길이 x16 링크 1 개 노트: 라이저 1 에서 슬롯을 사용하고 라이저 2 에 서 x16 링크를 사용하려면 두 프로세서를 모두 설 치해야 합니다.
메모리 UDIMM 최대 128GB 드라이브 하드 드라이브 최대 4 개의 2.5 인치 내장형 핫 스왑 가능 SAS, SATA 또는 Nearline SAS 하드 드라이브 노트: 4 하드 드라이브 시스템에서는 소프트웨어 RAID 를 지원합니다. 소프트웨어 RAID 에 대한 자 세한 내용은 support.dell.com/manuals 에서 Dell PowerEdge RAID 컨트롤러(PERC) 설명서를 참조하 십시오. 광학 드라이브 SATA DVD-ROM 드라이브 또는 DVD+/-RW 드라이브 1 개(선택 사양) 노트: DVD 장치는 데이터 전용입니다. 커넥터 후면 NIC 10/100/1000Mbps 4 개, 10/100/1000Mbps 2 개 및 100Mbps/1Gbps/10Gbps 2 개 직렬 9 핀, DTE, 16550 호환 USB 4 핀 2 개, USB 2.0 호환 비디오 15 핀 VGA 전면 USB 4 핀 2 개, USB 2.
비디오 비디오 종류 통합 Matrox G200 비디오 메모리 16MB 공유 환경적 특성 노트: 특정 시스템 구성을 위한 환경 측정에 대한 추가 정보는 dell.com/environmental_datasheets 를 참조하 십시오. 표준 작동 온도 연속 작동: 10% - 80% 상대 습도(RH)에서 10°C - 35°C, 최 대 이슬점은 26°C 입니다. 900m 이상인 경우 최대 허용 건구 온도는 1°C/300m(1°F/550ft)로 감소됩니다. 보관 온도 –40°C ~ 65°C(–40°F ~ 149°F), 시간당 최고 20°C 의 온도 변화 기준 확대된 작동 온도 노트: 확대된 온도 범위에서 작동하는 경우 시스템 성능에 영향을 줄 수 있습니다. 노트: 확대된 온도 범위에서 작동하는 경우 주위 온도 경고가 LCD 및 시스템 이벤트 로그에 보고될 수 있습니다.
8 시스템 메시지 LCD 메시지 노트: 시스템에 LCD 디스플레이가 있는 경우에만 사용할 수 있습니다. LCD 메시지는 SEL(시스템 이벤트 로그)에 기록된 이벤트를 참조하는 간단한 텍스트 메시지로 구성되어 있습니 다. SEL 및 시스템 관리 설정 구성에 대한 자세한 내용은 시스템 관리 소프트웨어 설명서를 참조하십시오. 노트: 시스템이 부팅되지 않는 경우 LCD 에 오류 코드가 표시될 때까지 시스템 ID 단추를 5 초 이상 누르십 시오. 코드를 기록하고 시스템 오류 메시지를 참조하십시오. LCD 메시지 보기 시스템 오류가 발생하면 LCD 화면이 황색으로 바뀝니다. 오류 또는 상태 메시지의 목록을 보려면 Select(선택) 단 추를 누르십시오. 왼쪽 및 오른쪽 단추를 사용하여 오류 번호를 강조 표시하고 Select(선택) 단추를 눌러 오류를 확인합니다. LCD 메시지 제거 센서와 관련된 오류(예: 온도, 전압, 팬 등)일 경우 센서가 정상 상태로 회복되면 LCD 메시지는 자동으로 제거됩 니다.
오류 코드 메시지 정보 AMP0302 메시지 The system board current is greater than the upper warning threshold(시스템 보 드 의 전류가 경고 임계값 상한보다 높습니다). 상세 정 보 시스템 보드 의 전류가 최적 범위를 벗어납니다. 작업 1. 시스템 전원 정책을 검토합니다. 2. 시스템 로그에서 전원 관련 오류를 점검합니다. 3. 시스템 구성 변경 사항을 검토합니다. 4. 문제가 계속되면 도움말 얻기를 참조하십시오. AMP0303 메시지 The system board current is greater than the upper critical threshold(시스템 보 드 의 전류가 중대 임계값 상한보다 높습니다). LCD 메시지 System board current is outside of range(시스템 보드 의 전류가 범위 를 벗어납니다).
오류 코드 메시지 정보 ASR0003 BAT0002 BAT0017 CPU0000 CPU0001 CPU0005 메시지 The watchdog timer power cycled the system(Watchdog 타이머가 시스템 전원을 껐다가 켰습니다). 상세 정 보 운영 체제 또는 응용프로그램이 타임 아웃 기간 내에 통신하지 못했습니다. 시스템 전 원이 꺼졌다가 켜졌습니다. 작업 운영 체제, 응용프로그램, 하드웨어 및 시스템 이벤트 로그에서 예외 이벤트가 있는지 확인합니다. 메시지 The system board battery has failed(시스템 보드 전지에 오류가 발생했습니다). LCD 메시지 The system board battery has failed. Check battery(시스템 보드 전지에 오류가 발생했 습니다. 전지를 점검하십시오). 상세 정보 시스템 보드 전지가 없거나 불량입니다. 작업 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 CPU0010 CPU0023 CPU0204 LCD 메시지 CPU configuration is unsupported. Check CPU or BIOS revision(CPU 구성이 지원되지 않습니다. CPU 또는 BIOS 버전을 확인하십시오). 상세 정보 시스템이 부팅하지 못하거나 성능이 저하된 상태로 실행될 수 있습니다. 작업 기술 사양을 검토하여 지원되는 프로세서 유형을 확인하십시오. 메시지 CPU is throttled(CPU 사용률이 조절되고 있습니다). 상세 정보 온도 또는 전원 상태로 인해 CPU 사용률이 조절되고 있습니다. 작업 시스템 로그를 검토하여 전원 또는 온도 예외가 있는지 확인합니다. 메시지 CPU is absent(CPU 이(가) 없습니다). LCD 메시지 CPU is absent.
오류 코드 메시지 정보 CPU0701 메시지 CPU protocol error detected(CPU 프로토콜 오류가 감지되었습니 다). LCD 메시 지 CPU protocol error detected. Power cycle system(CPU 프로토콜 오 류가 감지되었습니다. 시스템 전원을 껐다가 켜십시오). 상세 정 보 시스템 이벤트 로그 및 운영 체제 로그에서는 예외가 프로세서 외부에 있다고 기록될 수 있습니다. 작업 1. 시스템 및 운영 체제 로그에서 예외를 확인합니다. 예외가 발견되지 않으면 다 음을 계속하십시오. 2. 시스템을 끄고 입력 전원을 1 분 동안 분리합니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 입력 전원을 다시 연결하고 시스템을 켭니다. 5. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 CPU0704 메시지 CPU machine check error detected(CPU 시스템 검사 오류가 감지되 었습니다). LCD 메시 지 CPU machine check error detected. Power cycle system(CPU 시스템 검사 오류가 감지되었습니다. 시스템 전원을 껐다가 켜십시오). 상세 정 보 시스템 이벤트 로그 및 운영 체제 로그에서는 예외가 프로세서 외부에 있다고 기록될 수 있습니다. 작업 1. 시스템 및 운영 체제 로그에서 예외를 확인합니다. 예외가 발견되지 않으면 다 음을 계속하십시오. 2. 시스템을 끄고 입력 전원을 1 분 동안 분리합니다. 3. 프로세서가 올바르게 장착되었는지 확인합니다. 4. 입력 전원을 다시 연결하고 시스템을 켭니다. 5. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 HWC2003 HWC2005 MEM0000 MEM0001 MEM0007 메시지 The storage cable is not connected, or is improperly connected.(스토리지 케이블이 연결되어 있지 않거나 잘못 연결되어 있습니다.) LCD 메시지 Storage cable or interconnect failure. Check connection.(스토리지 케 이블 또는 상호 연결에 오류가 있습니다. 연결을 확인하십시오.) 상세 정보 올바르게 작동하려면 케이블이 필요할 수 있습니다. 시스템 기능이 저하될 수도 있 습니다. 작업 케이블이 있는지 확인하고 다시 설치하거나 다시 연결합니다. 메시지 The system board cable is not connected, or is improperly connected.
오류 코드 메시지 정보 MEM0701 MEM0702 MEM1205 MEM1208 MEM8000 116 메시지 Correctable memory error rate exceeded for (수정 가능한 메모리 오류 비율이 에 대해 초과되었습니다). 상세 정 보 메모리가 작동하지 않을 수 있습니다. 이 메시지는 복구할 수 없는 오류가 향후에 발 생할 수 있음을 미리 알려 줍니다. 작업 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Correctable memory error rate exceeded for (수정 가능한 메모리 오류 비율 이 에 대해 초과되었습니다). LCD 메시 지 Correctable memory error rate exceeded for .
오류 코드 메시지 정보 작업 PCI1302 PCI1304 PCI1308 PCI1320 PCI1342 시스템 로그를 검토하여 메모리 예외가 있는지 확인합니다. 위치에 메모 리를 다시 설치하십시오. 메시지 A bus time-out was detected on a component at bus device function . (버스 장치 기능 에 있는 구성부품에서 버스 시간 초과가 감지되 었습니다.) 상세 정 보 시스템 성능이 저하될 수 있습니다. 장치가 트랜잭션에 응답하지 못했습니다. 작업 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있 으면 해당 장치를 다시 설치하십시오. 메시지 An I/O channel check error was detected(I/O 채널 검사 오류가 감지되었습니다).
오류 코드 메시지 정보 PCI1348 PCI1360 PDR0001 PDR1016 PST0128 118 상세 정 보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있습니다. 작업 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다. 장치를 분리할 수 있 으면 해당 장치를 다시 설치하십시오. 메시지 A PCI parity error was detected on a component at slot (슬롯 에 있는 구성부품에서 PCI 패리티 오류가 감지되었습니다). LCD 메시 지 PCI parity error on slot . Re-seat PCI card(슬롯 에서 PCI 패리티 오 류가 감지되었습니다. PCI 카드를 다시 장착하십시오). 상세 정보 시스템 성능이 저하되거나 시스템이 작동하지 못하게 될 수 있습니다. 작업 입력 전원을 껐다가 켜고 구성부품 드라이버를 업데이트합니다.
오류 코드 메시지 정보 PST0129 PSU0001 PSU0002 PSU0003 PSU0006 LCD 메시지 No memory is detected. Inspect memory devices(메모리가 감지되지 않습니다. 메모리 장치를 검사하십시오). 상세 정보 시스템 BIOS 가 시스템에서 메모리를 감지하지 못했습니다. 작업 메모리 모듈을 다시 장착합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Memory is detected, but is not configurable(메모리가 감지되었으나 구성할 수 없습니 다). LCD 메시지 Memory is detected, but is not configurable. Check memory devices(메모리가 감지되었 으나 구성할 수 없습니다. 메모리 장치를 점검하십시오). 상세 정보 시스템 BIOS 가 메모리를 감지했지만 시스템 작동을 위해 메모리를 구성할 수 없었 습니다.
오류 코드 메시지 정보 PSU0016 LCD 메시지 Power supply is incorrectly configured. Check PSU(전원 공급 장치 이(가) 잘못 구성되어 있습니다. PSU 를 점검하십시오). 상세 정보 전원 공급 장치 간에 입력 유형 및 전원 정격이 동일해야 합니다. 작업 일치하는 전원 공급 장치를 설치하고 본 설명서에 기술된 올바른 구성을 검토하십 시오. 메시지 Power supply is absent(전원 공급 장치 이(가) 없습니다). LCD 메시지 PSU is absent. Check PSU(PSU 이(가) 없습니다. PSU 를 점검하십 시오). 상세 정보 전원 공급 장치가 제거되었거나 오류가 발생했습니다. 작업 1. 전원 공급 장치를 분리하고 다시 설치하십시오. 2. 케이블 및 시스템의 하위 시스템 구성부품이 손상되지 않았는지 확인하십시 오. 3.
오류 코드 메시지 정보 PSU0034 메시지 An under voltage fault detected on power supply .(전원 공급 장치 에 서 저전압 오류가 감지되었습니다.) LCD 메시 지 An under voltage fault detected on PSU . Check power source.(PSU 에서 저전압 오류가 감지되었습니다. 전원을 확인하십시오.) 상세 정보 이 오류는 케이블 또는 시스템의 하위 시스템 구성요소에 대한 전기 문제로 인해 발 생할 수 있습니다. 작업 1. 전원 공급 장치를 분리하고 다시 설치하십시오. 2. 케이블 및 시스템의 하위 시스템 구성부품이 손상되지 않았는지 확인하십시 오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. PSU0035 PSU0036 메시지 An over voltage fault detected on power supply .
오류 코드 메시지 정보 PSU1201 PSU1204 PWR1004 PWR1005 PWR1006 122 LCD 메시지 PSU wattage mismatch; PSU = watts(PSU 와트 불일치가 발생했습 니다. PSU 가 와트입니다.) 상세 정보 전원 공급 장치 간에 입력 유형 및 전원 정격이 동일해야 합니다. 작업 일치하는 전원 공급 장치를 설치하고 이 매뉴얼에서 적절한 구성을 검토합니다. 메시지 Power supply redundancy is lost(전원 공급 장치 중복성이 손실되었습니다). 상세 정 보 전원 공급 장치가 성능이 저하된 상태에서 작동하려고 시도합니다. 시스템 성능 및 전 원 중복성이 저하되거나 손실될 수 있습니다. 작업 입력 전원을 점검합니다. 전원 공급 장치를 다시 설치합니다. 문제가 계속되면 도움말 얻기를 참조하십시오.
오류 코드 메시지 정보 RFM1008 RFM1014 RFM1201 RFM2001 RFM2002 작업 시스템 구성을 검토하고 전원 공급 장치를 업그레이드하거나 시스템 전력 소비량 을 줄이십시오. 메시지 Failure detected on Removable Flash Media (이동식 플래시 미디어 에 서 오류가 감지되었습니다). LCD 메시지 Removable Flash Media failed. Check SD Card(이동식 플래시 미디어 에서 오류가 발생했습니다. SD 카드를 점검하십시오). 상세 정보 SD 카드 읽기 또는 쓰기 중에 오류가 보고되었습니다. 작업 플래시 미디어를 다시 장착합니다. 문제가 계속되면 도움말 얻기를 참조하십시오. 메시지 Removable Flash Media is write protected(이동식 플래시 미디어 이 (가) 쓰기 방지되어 있습니다).
오류 코드 메시지 정보 RFM2004 RFM2006 SEC0031 SEC0033 SEL0006 SEL0008 SEL0012 124 메시지 Failure detected on Internal Dual SD Module (내부 이중 SD 모듈 에서 오류가 감지되었습니다). LCD 메시지 Internal Dual SD Module failed. Check SD Card(내부 이중 SD 모듈 에 오류가 발생했습니다. SD 카드를 점검하십시오). 상세 정보 SD 카드 모듈이 설치되어 있지만 잘못 구성되거나 초기화되지 못했습니다. 작업 SD 모듈을 다시 설치하고 SD 카드를 분리한 후 다시 설치하십시오. 메시지 Internal Dual SD Module is write protected(내부 이중 SD 모듈 이(가) 쓰 기 방지되어 있습니다). 상세 정보 모듈이 쓰기 방지되어 있습니다.
오류 코드 메시지 정보 SEL1204 TMP0118 TMP0119 TMP0120 TMP0121 상세 정 보 시스템 이벤트 로그가 초기화되지 못하면 플랫폼 상태 및 오류 이벤트가 캡처되지 않 습니다. 일부 관리 소프트웨어는 플랫폼 예외를 보고하지 않습니다. 작업 관리 컨트롤러 또는 iDRAC 를 재부팅합니다. 시스템 입력 전원을 껐다가 켜십시오. 문 제가 계속되면 지원 부서에 연락하십시오. 메시지 An unknown system hardware failure detected(알 수 없는 시스템 하드웨어 오류가 감 지되었습니다). LCD 메시 지 Unknown system hardware failure(알 수 없는 시스템 하드웨어 오류입니다). 상세 정보 시스템 이벤트 로그를 초기화하지 못한 경우 플랫폼 상태 및 오류 이벤트가 캡처되 지 않습니다. 일부 관리 소프트웨어는 플랫폼 예외를 보고하지 않습니다. 작업 지원되는 최소 구성으로 시스템을 다시 구성합니다.
오류 코드 메시지 정보 VLT0204 메시지 The system board voltage is outside of the allowable range(시스템 보드 의 전압이 허용 범위를 벗어납니다). LCD 메시 지 System board voltage is outside of range(시스템 보드 전압이 범위를 벗어납니다). 상세 정보 시스템 하드웨어가 과전압 또는 저전압 상태를 감지했습니다. 전압 예외가 연속으로 여러 개 발생하는 경우, 비상 모드에서 시스템 전원이 꺼질 수 있습니다. 작업 1. 시스템 로그를 검토하여 전원 공급 장치 예외가 있는지 확인합니다. 2. 시스템을 최소 구성으로 재구성하고 시스템 케이블을 점검한 후 다시 설치하십 시오. 3. 문제가 계속되면 도움말 얻기를 참조하십시오. 경고 메시지 경고 메시지는 발생 가능한 문제를 경고하고 시스템이 작업을 계속하기 전에 사용자가 응답하도록 요청합니다.
9 지원 받기 Dell 에 문의하기 노트: 인터넷 연결을 사용할 수 없는 경우에는 제품 구매서, 포장 명세서, 청구서 또는 Dell 제품 카탈로그에 서 연락처 정보를 찾을 수 있습니다. Dell 은 다양한 온라인/전화 기반의 지원 및 서비스 옵션을 제공합니다. 제공 여부는 국가/지역 및 제품에 따라 다 르며 일부 서비스는 소재 지역에 제공되지 않을 수 있습니다. 판매, 기술 지원 또는 고객 서비스 문제에 대해 Dell 에 문의하려면 1. support.dell.com 을 참조하십시오. 2. 지원 카테고리를 선택합니다. 3. 미국 거주 고객이 아닌 경우, support.dell.com 페이지 하단에서 국가 코드를 선택하거나 모두를 선택하여 더 많은 옵션을 표시할 수 있습니다. 4. 필요한 서비스 또는 지원 링크를 선택하십시오.