Precision 3930 Rack Zoom card Installation Guide Regulatory Model: D24M Regulatory Type: D24M003
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Before you begin............................................................................................................................................ 4 Safety instructions............................................................................................................................................................. 4 Before working inside your computer........................................................................................................................
1 Before you begin Safety instructions Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
Safety precautions The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions. Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or reassembly: • • • • • • Turn off the system and all attached peripherals. Disconnect the system and all attached peripherals from AC power. Disconnect all network cables, telephone, and telecommunications lines from the system.
• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads. • When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static electricity from your body.
Transporting sensitive components When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport. Lifting equipment Adhere to the following guidelines when lifting heavy weight equipment: CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device. 1 Get a firm balanced footing.
2 Installing the Dell ultraspeed drive duo card 1 Follow the procedure in Before working inside your computer. NOTE: System sounds an alarm for 4 seconds and shut down if top cover is removed while the system is running. The system will not power on if the top cover is removed. 2 To remove the cover: a b c 3 Rotate lock on latch with a Phillips screw driver to release the lock [1]. Pull the latch to release the top cover [2]. Lift the top cover away [3].
4 Holding the blue contact points remove the raiser1 module from the system. 5 Pull the release tab [1] to open the riser1 slot and lift out the riser2 blank from the slot.
6 Install the Zoom card: 10 a Press the release latch on the Zoom card cover [1] and lift the cover open [2]. Remove the one (M2x2.5) screw [3]. b Insert the SSD card into the slot on the module [1], Replace the one (M2x2.5) screw [2] that secures the SSD card and close the module cover [3].
c Slide the zoom card into the riser 1 slot 2 [1]. Close the riser 2 module release latch [2]. 7 Holding the blue contact points align the module with the alignment pins on the chassis and insert the riser1 module into the slot. 8 Install the cover: a Align the top cover tabs with the slots on the system chassis [1] and slide it into the slot. b NOTE: Ensure that all internal cables are routed correctly and connected before securing the top cover.
9 Follow the procedure in After working inside your computer.
3 Getting help Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Go to Dell.com/support. 2 Select your support category.